Mercedes Benz G-class (W463)

Mercedes Benz G-class (W463)
Mercedes Benz G-class
INSTALLATION MANUAL
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD FRONT BUMPER FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
FRONT BUMPER
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
PARTS
FRONT BUMPER
FRONT GRILLE
MESHES FOR FRONT BUMPER
MESH FOR FRONT GRILLE
LED LAMP KIT
RUBBER MOLDING
BOLTS (M6 x 12)
RUBBER WASHERS
QUANTITIES
1
1
1 SET
1
1 SET
1 SET
14
6
Use caulking glue
to fill the gap
between the product
and the body.
FRONT BUMPER & FRONT GRILLE
【BEFORE PAINTING】
1) Remove OEM front bumper according to the Mercedes-Benz service manual.
※Use the bracket (sold separately) to fix OEM intercooler to the body only for Turbo Model.
2) Relocate all the necessary OEM parts and WALD Front Grille to WALD Front Bumper.
※ Adjust the details of WALD Front Bumper to fit the body by rasps or sandpapers.
3) Paint WALD Front Bumper and Front Grille according to the picture.
【AFTER PAINTING】
4) Install the attached meshes to WALD Front Bumper and Front Grille with caulking glue.
5) Fix the attached LED lamps and WALD Front Grille to WALD Front Bumper.
※ Adjust optical axis, and make sure the LED lamps are fine to work before the installation.
6) Temporarily fix the attached rubber moldings to WALD Front Bumper.
7) Check all the balance of the location and fitting,then tighten all the OEM and attached bolts.
8) Cut the pins on the back of OEM front grille emblem,
and use the caulking glue to fix it on WALD Front Grille.
※ Leave it till completely fixed.
■HOW TO FIX OEM INTERCOOLER TO THE BODY (Step 1)
INTERCOOLER
OEM PLASTIC NUT
BRACKET
OEM BOLTS
OEM NUT
BRACKET (SOLD SEPARATELY)
■WALD SHOWCAR IS PAINTED LIKE THE PICTURE (STEP 3)
Make clear coating for the carbon parts
of WALD Front Bumper.
ATTACHED MESH
OEM BOLTS
※Fix OEM bolts with the OEM fixture.
ATTACHED
RUBBER MOLDING
ATTACHED BOLTS (M6 x 12) & RUBBER WASHERS
※Fix WALD Over Fender and Front Bumper together.
■HOW TO INSTALL THE ATTACHED MESHES
(STEP 4)
Use pins and caulking glue to install
the attached meshes to WALD Front Bumper
from the rear.
※Paint the inside of the ducts and pins in black.
OEM BOLTS
※Fix OEM bolts through the attached brackets
on WALD Front Bumper.
MATTE BLACK
ATTENTION
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
WALD. INTERNATIONAL
WALD FRONT GRILLE
※Use the attached bolts (M6 x 12)
OEM EMBLEM
※Cut the pins on the back. to fix from the rear of WALD Front Bumper.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
ATTACHED LED LAMP
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
Recommend to paint protective coating
on the back side of WALD Over Fender.
2013/04
INSTALLATION MANUAL
Mercedes Benz G-class
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD REAR BUMPER FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
REAR BUMPER
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
PARTS
REAR BUMPER
MESHES
RUBBER MOLDING
BOLTS (M6 x 12)
NUTS (M8)
RUBBER WASHERS
QUANTITIES
1
1 SET
1 SET
6
4
6
Use caulking glue
to fill the gap
between the product
and the body.
REAR BUMPER
【BEFORE PAINTING】
1) Remove OEM rear bumper according to the Mercedes-Benz service manual.
2) Replace OEM brackets to WALD Rear Bumper.
3) Temporarily fix WALD Rear Bumper to the body with all the necessary parts.
※ Adjust the details of WALD Rear Bumper to fit the body by rasps or sandpapers.
4) Cut OEM mud-guard according to the shape of WALD Rear Bumper.
5) Paint WALD Rear Bumper according to the picture.
■HOW TO INSTALL OEM BRACKET (STEP 2)
Replace OEM brackets from OEM Rear Bumper,
and fix them on WALD Rear Bumper with OEM bolts
and attached Nuts (M8).
【AFTER PAINTING】
6) Use caulking glue to fix the attached meshes from the rear.
7) Fix OEM mud-guard to WALD Rear Bumper.
※ Use caulking glue if the OEM tapping screws are not available.
8) Temporarily install WALD Rear Bumper to the body.
9) Check all the details of the fitment, then tighten all the OEM bolts and the attached bolts.
Recommend to paint protective coating
on the back side of WALD Over Fender.
OEM BRACKET
■HOW TO INSTALL
OEM MUD-GUARD (STEP 4)
ATTACHED BOLTS (M6 x 12) &
RUBBER WASHERS
※Fix WALD Over Fender and
Rear Bumper together.
Cut the part according to
WALD Rear Bumper.
OEM MUD-GUARD
OEM BOLT
ATTACHED NUT (M8)
Cut here
(About 8 cm)
ATTACHED RUBBER MOLDING
■WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 5)
Make clear coating for the carbon parts
of WALD Front Bumper.
■HOW TO INSTALL THE
ATTACHED MESHES (STEP 6)
Use pins and caulking glue to install the
attached meshes to WALD Rear Bumper
from the rear.
※Paint the inside of the ducts and pins in black.
MATTE BLACK
OEM BOLT
※Fix OEM bolts through the
replaced brackets on
WALD Rear Bumper.
ATTACHED MESH
ATTENTION
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
OEM REAR FOG LAMP
(Replace from OEM Rear Bumper)
LICENSE PLATE LIGHT
(Replace from OEM Rear Bumper)
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
OEM BACK-UP LIGHT
(Replace from OEM Rear Bumper)
2013/04
Mercedes Benz G-class
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD HEAD LIGHT COVER FOR MERCEDES-BENZ W463 G-CLASS.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
PARTS
HEAD LIGHT COVER
LED LAMP
REAR BUMPER
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
QUANTITIES
1 SET
1 SET
Use caulking glue
to fill the gap
between the product
and the body.
HEAD LIGHT COVER
【AFTER PAINTING】
6)Completely degrease the installation positions
for WALD Exhaust Trim.
7)Use caulking glue to fix WALD Exhaust Trim
on WALD Rear Bumper.
8)Leave them till completely fixed.
9)Install WALD Rear Bumper to the body.
※WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 5)
= WIRING DIAGRAM =
■ HOW TO INSTALL THE
ATTACHED LED LAMPS (STEP 2, 7)
[ AS DAYLIGHT ]
(Inside of WALD Head Light Cover)
LED LAMP
RELAY
BOX
RED
IGNITION
BLACK
GROUNDING WIRE
BLUE
POSITION LAMP
CAR SIDE
【BEFORE PAINTING】
1)Remove OEM head light cover according
to the Mercedes-Benz service manual.
2)Temporarily install the attached LED lamps according
to the guide-wall on WALD Head Light Cover.
※Adjust the details of WALD Head Light Cover to fit the
attached LED lamps by rasps or sandpapers.
3)Temporarily install WALD Head Light Cover to the body.
※Adjust the details of WALD Head Light Cover to fit
the body by rasps or sandpapers.
4)Prepare to connect the LED lamps.
※Insulate any spare harness.
5)Paint WALD Head Light Cover according to the picture.
※Insulate OEM fog lamp harness.
ATTACHED LED LAMP
LED LAMP GUIDE-WALL
※ Use heat resistant caulking glue
to fix the attached LED lamps.
OEM HEAD LIGHT WASHER
(Face of lens)
Fix the attached LED lamps according to the picture.
Make clear coating for the carbon parts
of WALD Front Bumper.
MATTE BLACK
ATTENTION
OEM TAPPING SCREWS
ATTACHED LED LAMP
※MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK. DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
2013/04
Mercedes Benz G-class
INSTALLATION MANUAL
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD BONNET FOR MERCEDES-BENZ W463 G-CLASS.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
LED LAMP
LED LAMP
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
PARTS
QUANTITIES
1 SET
Use caulking glue
to fill the gap
between the product
and the body.
LED LAMP KIT
【BEFORE PAINTING】
1)Temporarily fix the attached LED lamps according
to the guide-line wallls on WALD Front Bumper.
※Adjust the details of WALD Front Bumper to fit the
attached LED lamps by rasps or sandpapers.
= WIRING DIAGRAM =
■HOW TO INSTALL THE ATTACHED
LED LAMPS (STEP 1, 3)
LED LAMP
2)Prepare to connect the attached LED lamps.
※Insulate any spare harness.
[ AS FOG LAMP ]
ATTACHED BOLTS (M5 x 15)
RELAY
BOX
3)Paint WALD Bonnet according to the picture.
5)Use caulking glue to fix the attached LED lamps
after checking the angle and location.
6)Leave them till completely fixed.
LED
GUIDE-LINE
ATTACHMENT WALL
LED LAMP
LED LAMP
(Face of the lens)
ATTACHED BOLTS (M5 x 15)
※ WALD SHOWCAR IS PAINTED LIKE THE PICTURE
(STEP 4)
The LED attachment of WALD Show Car
is painted in Matte Black.
Make clear coating for the
carbon parts of WALD Front Bumper.
ATTENTION
Even for Carbon Products,
WALD Show Car is painted
in Matte Black for these parts.
FOG LAMP
⊕
BLACK
FOG LAMP
⊖
BLUE
NOT CONNECTING
[ AS DAYLIGHT ]
※ Use heat resistant caulking glue
to fix the attached LED lamps.
7)Install WALD Front Bumper to the body
after connecting the harness.
RED
RELAY
BOX
RED
IGNITION
BLACK
GROUNDING WIRE
BLUE
POSITION LAMP
CAR SIDE
【AFTER PAINTING】
4)Completely degrease the installation positions,
then put the atached LED lamps according
to the guide-line walls on WALD Front Bumper.
LED LAMP
※Insulate OEM fog lamp harness.
Fix the attached LED lamps
according to the picture.
■ Please purchase relay harness with remote controller kit
to turn on the daylights or fog lamps separately.
※REMOVE THE BATTERY BEFORE ALL THE WIRING WORKS.
※MAKE SURE OEM FOG LAMPS ARE FINE TO WORK BEFORE THE INSTALLATION.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
LED LAMP KIT
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
2013/04
INSTALLATION MANUAL
Mercedes Benz G-class
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD BONNET FOR MERCEDES-BENZ W463 G-CLASS.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
PARTS
BONNET
BOLTS (M6 x 12)
NUTS (M8)
BONNET
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
QUANTITIES
1
2
1
Use caulking glue
to fill the gap
between the product
and the body.
BONNET
【BEFORE PAINTING】
1)Remove OEM bonnet according to the Mercedes-Benz
service manual.
2)Temporarily install WALD Bonnet to the body after
pre-fixing all the necessary parts.
※Adjust the details of WALD Bonnet to fit the body
by rasps or sandpapers.
■HOW TO REPLACE OEM WASHER PANEL
(STEP 2)
Replace OEM washer panel to WALD Bonnet.
Use OEM Clips to fix on WALD Bonnet
3)Paint WALD Bonnet according to the picture.
HINGES (Replace from OEM bonnet)
BONNET RELEASE LEVER
(Replace from OEM bonnet)
RUBBER CUSHIONS
(Replace from OEM bonnet)
OEM BONNET GRILLE
【AFTER PAINTING】
4)Fix all the necessary parts to WALD Bonnet,
then install to the body.
OEM LEAF SPRINGS
ATTACHED BOLTS
(M6 x 12)
5)Tighten OEM bolts, attached bolts and nuts after
checking the balance.
ATTACHED NUT
(M8)
※WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 3)
Make clear coating for the carbon
parts of WALD Front Bumper.
OEM BOLTS
OEM BOLTS
OEM BONNET INSULATION
Use heat-resistant glue to fix
on OEM bonnet.
MATTE BLACK
ATTENTION
※MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
2013/04
INSTALLATION MANUAL
Mercedes Benz G-class
(W463)
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD OVER FENDER AND REAR DOOR PANEL FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
OVER FENDER
REAR DOOR PANEL
PARTS
QUANTITIES
OVER FENDER
INNER PANELS
MESHES
REAR DOOR PANELS
FENDER PANELS
1 SET
1 SET
1 SET
1 SET
1 SET
Use caulking glue
to fill the gap
between the product
and the body.
OVER FENDER & REAR DOOR PANEL
【BEFORE PAINTING】
1) Remove OEM over fender according to the Mercedes-Benz service manual.
2) Temporarily install WALD Over Fender to the body.
※ See how to process on WALD Rear Over Fender when installing WALD Door Panel
according to the picture.
3) Mark the installation positions for OEM tapping screws on the attached inner panels
to fix on WALD Rear Over Fenders.
4) Make holes on the attached inner panels according to the marked positions.
5) Paint WALD Over Fenders according to the picture.
■HOW TO INSTALL THE
ATTACHED INNER PANELS (STEP 2)
Use OEM tapping screws to connect
the attached inner panels with
OEM inner liners.
※Adjust the shape and
location based on OEM inner liners.
ATTACHED INNER PANE
【AFTER PAINTING】
6) Use caulking glue to fix the attached meshes from the rear.
7) Fix the attached inner panels on WALD Rear Over Fenders.
8) Install WALD Over Fenders to the body and tighten OEM bolts and tapping screws.
■WALD SHOWCAR IS PAINTED
LIKE THE PICTURE (STEP 5)
WALD REAR OVER FENDER
OEM
OVER FENDER
MOLDING
Use OEM tapping screws for
WALD Front and Rear
Over Fenders.
ATTACHED MESH
Make clear coating for the carbon parts
of WALD Front Bumper.
WALD DOOR PANEL & FENDER PANEL
■HOW TO INSTALL THE
ATTACHED MESHES (STEP 6)
Use pins and caulking glue to install the
attached meshes to
WALD Rear Bumper from the rear.
※Paint the inside of the ducts and pins in black.
OEM NUTS
■HOW TO PROCESS WALD REAR OVER FENDER (STEP 2)
OEM
OVER FENDER
MOLDING
Need to cut WALD Rear Over Fender and
OEM Door Molding when installing
WALD Rear Door Panels.
MATTE BLACK
Cut here.
OEM BOLTS
ATTENTION
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
WALD. INTERNATIONAL
Be careful to adjust the location and
balance based on a car.
Recommend to paint protective coating on the back side of WALD Over Fender.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
2013/04
INSTALLATION MANUAL
Mercedes Benz G-class
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD FRONT BUMPER FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
ATTENTION
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
【BEFORE PAINTING】
1)Temporarily install WALD Roof Spoiler and Rear Gate Spoiler to the body.
※Check all the details of the fitment, then use masking
tape to mark the installation position.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
ROOF SPOILER
REAR GATE SPOILER
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
PARTS
ROOF SPOILER
TAPPING SCREWS (M5 x 10)
REAR GATE SPOILER
QUANTITIES
1
4
1
Use caulking glue
to fill the gap
between the product
and the body.
Scuff and degrease the surface of
WALD Roof Spoiler and the body before installing.
2)Mark the installation positions on the body according to the picture,
then remove WALD Rear Gate Spoiler and Roof Spoiler.
3)Make holes on the rear gate from the rear to insert the attached tapping screws.
※Use touch up paint to make corrosion treatment on holes.
4)Remove WALD Roof Spoiler and Rear Gate Spoiler, then make holes on them.
【AFTER PAINTING】
5)Use caulking glue to install WALD Rear Gate Spoiler
and Roof Spoiler to the body after completely degreasing the installation positions.
6)Fix the attached tapping screws from the rear gate
to install WALD Roof Spoiler.
7)Check all the details of the fitment, then fix the
attached tapping screws.
■HOW TO MAKE HOLES (STEP 3)
Taking off the cover inside of the rear gate,
then make holes.
※Insulate the holes for the purpose of
waterproof and anti-rust.
ATTACHED LED LAMP
OPENING
ATTENTION
(Inside of WALD Roof Spoiler)
※MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ADJUST ALL THE DETAILS OF WALD PRODUCTS TO FIT ON THE BODY.
WALD. INTERNATIONAL
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
2013/04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement