Century 400 NINJA Warrior NWCU2350N Operating Instructions Manual

Century 400 NINJA Warrior NWCU2350N is an electric powered carpet extractor intended for commercial use. It applies a cleaning solution to the carpet and then vacuums the soiled water back into the recovery tank. With its powerful 500 PSI pump, it ensures deep cleaning of carpets, removing dirt, stains, and allergens effectively.

PDF

Document

500 PSI

Operating instructions (ENG)

MODELS:

NWCU2250N

10070620

NWCU2250H

10070680

NWCU2350N

10070690

86322410-V

11/07/14

Read these instructions before using the machine.

Machine Data Log / Overview

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

OVERVIEW

The Ninja Warrior is an electric powered carpet extractor intended for commercial use. This appliance applies a cleaning solution to the carpet and then vacuums the soiled water back into the recovery tank.

Warranty Registration

Thank you for purchasing a C400 product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product.

To register you product go to : www.century400.com/support/warranty/register.php

For customer assistance:

1-800-776-2436

86322410 NINJA WARRIOR 500 PSI

Machine Data Log / Overview. . . . . . . . . . . . . . . . . .2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3

How to Use This Manual . . . . . . . . . . . . . . . . . . . . . .4

Safety

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5

HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . .6

Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . .8

Operations

Technical Specifications . . . . . . . . . . . . . . . . . . . . . .9

Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . .11

Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Pre-Run Inspection . . . . . . . . . . . . . . . . . . . . . . . . .12

Equipment Set-up . . . . . . . . . . . . . . . . . . . . . . . . . .12

Heater Operation . . . . . . . . . . . . . . . . . . . . . . . . . .12

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

PARTS

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Control Panel with Heat . . . . . . . . . . . . . . . . . . . . 22

Electrical with 2 Stage Vacuum . . . . . . . . . . . . . . 24

Electrical with Heat / 3 Stage Vacuum . . . . . . . . . 26

Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Pump with Heat. . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Vacuum, 2-Stage / 3-Stage. . . . . . . . . . . . . . . . . . 42

Wiring - 2 Stage Vacuum . . . . . . . . . . . . . . . . . . . 44

Wiring - 3 Stage Vacuum . . . . . . . . . . . . . . . . . . . 46

Wiring with Heat . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Suggested Spare Parts. . . . . . . . . . . . . . . . . . . . . 50

Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Maintenance

Periodic Maintenance . . . . . . . . . . . . . . . . . . . . . . .14

Daily/Regular Maintenance. . . . . . . . . . . . . . . . . . .14

Vacuum Motor Replacement . . . . . . . . . . . . . . . . .15

Solution Pump Replacement . . . . . . . . . . . . . . . . .16

Pressure Regulator . . . . . . . . . . . . . . . . . . . . . . . . .17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .18

86322410 NINJA WARRIOR 500 PSI 3

How to Use This Manual

This manual contains the following sections:

• How to Use This Manual

• Safety

• Operations

• Maintenance

• Parts List

The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.

Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the

MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

The model and serial number of your machine is located approximately where shown.

Serial Number

Tag

The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death.

The OPERATIONS section is to familiarize the operator with the operation and function of the machine.

The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order:

• Maintenance

• Lubrication

• Vacuum Motor Replacement

• Solution Pump Replacement

• Troubleshooting

The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:

• REF – column refers to the reference number on the parts illustration.

• PART NO.

– column lists the part number for the part.

• PRV NO. – reference number.

• QTY – column lists the quantity of the part used in that area of the machine.

• DESCRIPTION – column is a brief description of the part.

• SERIAL NO. FROM – If this column has an (*) and a Reference number, see the SERIAL

NUMBERS page in the back of your manual. If column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.

• NOTES – column for information not noted by the other columns.

NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.

NOTE: The manual part number is located on the lower left corner of the front cover.

4 86322410 NINJA WARRIOR 500 PSI

Safety

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

This machine is for commercial use.

To reduce the risk of fire, electric shock, or injury:

Connect to a properly grounded outlet . See Grounding Instructions.

Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service.

Use only indoors. Do not use outdoors or expose to rain.

Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.

Use only as described in this manual. Use only manufacturer's recommended components and attachments.

Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the machine. If the machine is not working properly , has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.

Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp edges or corners.

Do not run machine over cord. Keep cord away from heated surfaces.

Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.

Do not handle the electrical plug or machine with wet hands.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

This machine is intended for cleaning carpet only.

Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

This machine is not suitable for picking up health endangering dust.

Turn off all controls before unplugging.

Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

SAVE THESE INSTRUCTIONS

86322410 NINJA WARRIOR 500 PSI 5

Safety

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words WARNING and CAUTION and FOR SAFETY .

The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine.

Use only manufacturer approved replacement parts.

6 86322410 NINJA WARRIOR 500 PSI

Safety

Safety Labels

NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them.

Label Warning

86244300

PRV # 500955

WARNING!

FOR YOUR PROTECTION USE A

GROUND FAULT CIRCUIT INTERRUPTER

Label Circuit Interrupter

86200570

PRV # 170-41

86322410 NINJA WARRIOR 500 PSI 7

Safety

Grounding Instructions

THIS PRODUCT IS FOR COMMERCIAL

USE ONLY.

ELECTRICAL:

In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.

EXTENSION CORDS:

If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.

GROUNDING INSTRUCTIONS:

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in "Fig.

A". A temporary adaptor that looks like the adaptor in

"Fig. C" may be used to connect this plug to a 2-pole receptacle as shown in "Fig. B", if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adaptor is used, it must be held in place by a metal screw.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

8 86322410 NINJA WARRIOR 500 PSI

Technical Specifications

MODEL

ALL

10070620

10070680

10070690

Electrical

Solution Pump

Solution Capacity

Recovery Capacity

Height

Length

Width

Vacuum Motor

Weight- Empty

Weight-Full Solution

Power cord

Vacuum Motor

Weight- Empty

Weight-Full Solution

Power cord

Heater

Vacuum Motor

Weight- Empty

Weight-Full Solution

Power cord

ITEM

Width

115 Volt, 60 hz, 15A

500 psi

13 Gal

11 Gal

43 inches

30 inches

22 inches

Dual 2 Stage

127 lbs

232 lbs

1 X 25 feet

Dual 2 Stage

134 lbs

239 lbs

2 X 25 feet

1850 watts

Dual 3 Stage

129 lbs

234 lbs

2 X 25 feet

MEASURE

Length

Operations

Height

86322410 NINJA WARRIOR 500 PSI 9

Operations

Controls

3 4 5 6

1. Vacuum Accessory Tool Hook-up

2. Solution Pump Switch

3. Vacuum 1 Switch

4. Vacuum 2 Switch

5. Heater Switch with On Light (Units w/Heat Only)

6. Pressure Gauge

9 8 7

7. Adjustable Pressure Relief Valve

8. Heater Temperature Light (Units w/Heat Only)

9. Breaker for Vacuum 2

10. Breaker for Vacuum 1

11. Solution Accessory Tool Hook-up

10 86322410 NINJA WARRIOR 500 PSI

Operations

Machine Operation

Care must be exercised in the use of all chemicals.

Chemicals are poisonous and can pose a health risk.

Read and follow manufacturers instructions regarding dangers and correct usages.

Only use chemicals approved for use with this machine. Use of non-compatible chemicals may cause machine damage and will not be covered under the warranty. Carefully read ingredients on manufacturer’s label before using any product in this machine.

Do not let pump run dry.

The internal parts of the pump used in the machine are suitable for use with most carpet cleaning chemicals.

But they are susceptible to chemical attack from some cleaning substances, such as hydrocarbon solvents and chlorinated bleaches. These non-compatible materials are not of the type used for carpet cleaning.

Chemicals

Suitable Chemicals

• Alkalis

• Detergents

• Hydroxides

• Soaps

• Vinegar

Non-Compatible

• Aldehydes

• Aromatics Hydrocarbons

• SP Butyls

• Carbon Tetrachloride

• Clorox*

• Chlorinated Bleaches

• Chlorinated Hydrocarbons

• Lysol*

• Methyl Ethel Ketone (MEK)

• Perchorethylene (perc)

• Phenolics

• Trichlorethylene

• D-Limonene

Do not let pump run unattended.

*Registered Trademark

86322410 NINJA WARRIOR 500 PSI 11

Operations

Pre-Run Inspection

1. Check all fittings and connectors for proper assembly.

2. Check all hoses for leaks. Repair or replace any damaged hoses.

3. Check power cord(s) for any damage. If damaged, replace.

Equipment Set-up

1. Plug power cord from machine into properly grounded wall outlet.

2. Turn vacuum motor switch on and off to make sure there is electrical power at machine.

3. Using a clean container, fill the solution tank with clean hot water. Do not use water over 130°F. Mix in a non-foaming cleaning concentrate for use in hot water extraction machines, following the manufacture's instructions printed on container.

4. Connect priming hose to solution fitting on machine. Turn on pump and run for 30 seconds or until a steady flow of water is coming out of priming hose. Turn off pump and disconnect priming hose.

5. Connect vacuum hose to machine. Slide the swivel cuff over the outlet on the tank.

6. Connect the hose to your machine and wand. Pull back the knurled collar on the quick disconnect coupler and push onto the connection on the chassis. To avoid leaks, check to be that a positive connection was made.

NOTE: When using a powder cleaner, pre-mix with hot water in a clean container before adding to the solution tank.

7. Turn pump and vacuum switch(es) to the on position.

Heater Operation

NOTE: Units with Heat Only

The solution fittings on the machine will become extremely hot during operation. Allow sufficient time to cool, or run solution through the machine with the heater turned off before disconnecting or performing any maintenance on the heater.

Plug the two power cords into separate grounded circuits. The heater draws 15 amps of current.

Turn the solution pump ON . Fully prime the solution system before turning heater on.

Turn the heater switch on. The red light on the heater switch will be on when the heater switch is on. The red heater temperature light will be on when the heater is active and will turn off when the heater reaches maximum temperature.

On initial start-up the heater will take a few minutes to reach operating temperature.

When turning the pump and heater OFF , make certain that you turn the heater off FIRST .

12 86322410 NINJA WARRIOR 500 PSI

Cleaning

Always use defoamer if foaming occurs. Foam will suspend large particles that may damage vacuum(s) as well as allow liquid into the vacuum motor(s) without activating the float shutoff.

1. Prior to cleaning, make certain that the nozzle is functioning properly.

a. To check, hold the wand about one foot above the surface to be cleaned and open the wand valve. A full spray should be observed from the nozzle.

b. If the nozzle is not showing a full spray pattern, adjust nozzle for proper pattern, clean, or replace nozzle.

2. Normally, chemical is applied on the push stroke of the wand when cleaning. Vacuuming is done on the pull stroke. For heavily soiled carpets the wand may be used in a scrubbing manner, applying chemical in both the push and pull stroke.

3. When cleaning, keep the working opening (wand mouth) flat on the surface being cleaned. Keep the wand moving when the valve is open.

4. The shutoff float inside the vacuum tank will impede the vacuum flow when the vacuum tank is full. When this occurs, empty the vacuum tank by opening the dump valve and dispose of the waste in a proper manner.

5. Once the vacuum tank has been emptied, you may once again proceed with cleaning

Operations

86322410 NINJA WARRIOR 500 PSI 13

Maintenance

Periodic Maintenance

Twice a month, flush a white vinegar solution (one quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the machine. This will prevent build-up of alkaline residue in the system.

Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum or solution pressure loss. The electrical cable must be well insulated and cable connector screw kept tight. If the cable insulation is broken or frayed, repair or replace immediately. Don't take chances with electrical fire or shock.

Daily/Regular Maintenance

Before making any repairs or adjustments to the machine, disconnect the power cords from the electrical source.

1. Empty unused cleaning solution from the solution tank.

2. Inspect and clean filter screen in solution tank.

3. Flush pumping system with 1 to 2 gallons of clean water.

4. After each use, rinse tank with fresh water. Periodically inspect the recovery tank and decontaminate if necessary, using a Hospital Grade Virucide or a

10-1 bleach to water solution. Waste water should be disposed of properly.

Do not allow machine to freeze.

SERVICE SCHEDULE

Check machine for cord damage

Check recovery dome and gasket for damage and cleanliness

Check hoses for wear, blockages, or damage

Check handles, switches, and knobs for damage

Run one gallon of water through solution system

Clean out recovery tank and check float valve to make sure it moves freely

Clean out solution tank and remove and clean vacuum intake screen

Clean outside of all tanks and check for damage

Run vac motor for at least one minute to allow motor to dry

Store with dome off tank to allow the tank to dry

Check all gaskets for wear and leakage

Check pump pressure; observe spray pattern and check with gauge if necessary

Check and clean solution screen

Check cables for fraying

Check overall performance of machine

Check vac motor carbon brushes

DAILY WEEKLY QUARTERLY

14 86322410 NINJA WARRIOR 500 PSI

Only qualified maintenance personnel are to perform the following repairs.

Vacuum Motor Replacement

1. Turn off all switches and unplug machine.

2. Remove hardware under front of machine to access component compartment.

3. Remove vacuum motor cover and disconnect motor wires.

4. Remove the vacuum motor.

5. Reverse process to install vacuum motor.

Maintenance

Vacuum Motor Carbon Brushes Replacement

End Cap

Carbon

Brushes

WARNING: The green ground wire must be attached for safe operation. See wiring diagram.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

8 [9.5mm]

Periodically check the length of the carbon brushes.

Replace both carbon brushes when either is less than

3/8" (9.5mm) long.

86322410 NINJA WARRIOR 500 PSI 15

Maintenance

Solution Pump Replacement

Only qualified maintenance personnel are to perform the following repairs.

Pump Replacement Kits

500 psi

Cam & Bearing Kit

86201040

PRV NO. 250-73C

Plunger & Seals Kit

86201080

PRV NO. 250-75A

16 86322410 NINJA WARRIOR 500 PSI

Valve & O-Rings Kit

(both sides)

86201030

PRV NO. 250-73B

Maintenance

Only qualified maintenance personnel are to perform the following repairs.

Pressure Regulator

For best results with the pressure regulator, we recommend that you clean and lubricate the piston and u-cup with Superlube lubricant monthly or when pressure drop seems excessive.

1. Turn unit off before lubricating.

2. Remove cap, spring and spring retainer plate.

3. With fingertips remove piston and u-cup.

4. Wipe piston and u-cup clean of any film or scale.

5. Lubricate the piston and u-cup with Superlube.

6. Reassemble regulator.

7. With pump ON, re-adjust pressure regulator for normal operation.

Lubricate U-Cup with Superlube Monthly.

REBUILD KIT

8.619-924.0

(GREEN 500 PSI)

86322410 NINJA WARRIOR 500 PSI 17

Maintenance

Troubleshooting

PROBLEM

Loss of Power

Electrical shock

Vac motor speed varies or doesn't run

Loss of vacuum

Pump runs no solution

Pump runs, loss of pressure

Pump will not run

Solution hose fitting hard to connect

Carpet not getting clean

Carpet too wet

Carpet browning

Solution not flowing properly

CAUSE

Unit not plugged in

Dead electrical circuit

Faulty power cord

Receptacle not grounded

Internal wiring problem

SOLUTION

Connect unit to 3 prong grounded outlet.

Check building circuit breaker or fuse box.

Replace

Contact an electrician to check building's wiring

Have a trained service technician check machine's wiring

Vacuum circuit breaker tripped

Faulty vacuum motor

Faulty switch

Loose vacuum dome

Crack in dome of poor joint

Check valves in pump head for particles or cuts in seals

Faulty switch

Loose wiring

Corrosion on fittings.

Severe soil conditions

Over saturation

Reset Breaker

Replace

Center and seal dome over tank

Replace or repair using acrylic plastic cement only

Lint or dirt clogging vacuum screen

Loose cuffs on vacuum hose

Vac motor seals leaking

Floor tool vac chamber clogged

With power off clean screen

Tighten cuffs turning counterclockwise

Replace

Wash out with hose. Pick lint out with a wire

Replace Vacuum hose damaged

Recovery tank full / Float ball stuck in the up position

Pump inlet screen plugged

Pump not primed

Turn off power, drain recovery tank.

Clean inlet screen

Prime pump with priming hose

Internal or external solution line damaged and leaking

Replace

Internal pump components wearing out Replace, see pump kit components

Take piston from BPR and lubricate with Superlube. If problem still exists change BPR kit

Replace

Repair or replace

Clean with steel wool. Soak in acetic acid (white vinegar). Lubricate lightly with silicone base lubricant.

Make several passes at right angles to each other. Use a pre-spray.

Adjust solution pressure to lower settings. Make several passes without spray

Leaving carpet too wet

Too much chemical

Solution hose connection

Faulty pump

Faulty floor tool valve / Nozzle

Faulty pump switch

Check for loss of vac pressure

Check label for correct solution concentration

Check for positive connection

Repair or replace

Repair

18 86322410 NINJA WARRIOR 500 PSI

PARTS

86322410 NINJA WARRIOR 500 PSI

Control Panel

20 86322410 NINJA WARRIOR 500 PSI

Control Panel

REF PART NO.

PRV NO.

QTY DESCRIPTION

86180350 12-800035 1 ELL, 1/4FP X 1/4T BR

86202230 390-09A 2 WASHER 9/16 S/S USS THICK

86002370

86002450

20035

22015

CLAMP, 7/16 DIA NYLON UL

COUPLER, 1/4 QD

86197390

86005700

86276820

86007140

31021

57104

70740

72130

ELBOW, 1/4NPT 45D STREET

NUT, 10-32 HEX W/STAR

SCR, 10-32 X 1/2 PTHMS BLK NP

SWITCH, SPST 2-POSITION ROCKER

9 86008900

10 86005720

11 86323500

12 86313020

13 86313030

14 86318320

15 86323310

80845

57106

BOOT, SEAL PUSH BUTTON 7/16”

NUT8-32 W/STAR WASHER PLTD

PANEL, CONTROL, 500

GASKET, .125 T X .25 W X 15.6”

GASKET, .125 T X .25 W X 7.2”

BREAKER, 13A, 250VAC, 32VDC

GAUGE, 0-600 PSI

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 21

Control Panel with Heat

22 86322410 NINJA WARRIOR 500 PSI

Control Panel with Heat

REF PART NO.

PRV NO.

QTY DESCRIPTION

86180350 12-800035 1 ELL, 1/4FP X 1/4T BR

86202230 390-09A 2 WASHER 9/16 S/S USS THICK

86002370

86002450

20035

22015

CLAMP, 7/16 DIA NYLON ULS

COUPLER, 1/4 QD

86197390

86005700

86276820

86007140

31021

57104

70740

72130

ELBOW, 1/4NPT 45D STREET

NUT, 10-32 HEX W/STAR

SCR, 10-32 X 1/2 PTHMS BLK NP

SWITCH, SPST 2-POSITION ROCKER

9 86008900

10 86311840

11 86313020

12 86313030

13 86318320

14 86323310

15 86318780

16 86317850

17 86233480

18 86005720

80845

57106

BOOT, SEAL PUSH BUTTON 7/16”

PANEL, CONTROL, 500 HEAT

GASKET, .125 T X .25 W X 15.6”

GASKET, .125 T X .25 W X 7.2”

BREAKER, 13A, 250VAC, 32VDC

GAUGE, 0-600 PSI

LIGHT ASM, HEATER, 120V

SWITCH, LIGHTED 2-POS ROCKER

CLIP, NEON LAMP

NUT8-32 W/STAR WASHER PLTD

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 23

Electrical with 2 Stage Vacuum

24 86322410 NINJA WARRIOR 500 PSI

Electrical with 2 Stage Vacuum

REF PART NO.

PRV NO.

QTY

1 86201510

2 86005670

3 86005700

4 86273830

5 86006850

6 86256200

7 86255900

8 86010630

9 86316460

10 86316540

11 86316700

12 86318620

13 86319090

14 86364350

15 86317580

16 86005810

17 86323330

18 86198460

19 86006590

57245

390-26

57040

57104

70020

70393

73200

73538

87013

20008

70088

DESCRIPTION

2 SPACER NYLON 1/4ID X 1/2 OD

1 NUT, 1/2 NPT CONDUIT

3 NUT, 10-32 W/STAR WASHER PLTD

2 SCR, 1/4-20 X 1/2 HHCS SS

2 SET SCR, 1/4-20 X 1.25L

1 STRAIN RELEIF, 1/2 NPT FLEX

2 STANDOFF, 6-32 X 5/8 HEX NYL

2 WASHER, 1/4 X 5/8 FLAT SS

1 BRKT, ELECTRICAL

1 CONNECTOR, 5 POS, PUSH WIRE

1 BRKT, CORD STRAIN RELIEF

1 CORD ASM, 14/3 SJT X 25' BLK

1 FUSE HOLDER, PANEL MNT

1 FUSE, 7A 1/4" X 1 1/4"

1 BRKT, CORD, BLANK

2 NUT, 1/4-20 NYLOCK

2 WASHER, 1/4" ID X 1.0D FLAT BLK

1 CLAMP, 5/8 NYLON UL/CSA

1 SCREW, 10-32 X 1/2 PPHMS SS NP

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 25

Electrical with Heat / 3 Stage Vacuum

26 86322410 NINJA WARRIOR 500 PSI

Electrical with Heat / 3 Stage Vacuum

REF PART NO. PRV NO. QTY DESCRIPTION

1 86201510 390-26 2 SPACER NYLON 1/4ID X 1/2 OD

2 86005670 57040 2 NUT, 1/2 NPT CONDUIT

3 86005700 57104

4 86273830 70020

NUT, 10-32 W/STAR WASHER PLTD

SCR, 1/4-20 X 1/2 HHCS SS

5 86006850 70393

6 86256200 73200

7 86255900 73538

8 86010630 87013

9 86316460 -

SET SCR, 1/4-20 X 1.25L

STRAIN RELEIF, 1/2 NPT FLEX

STANDOFF, 6-32 X 5/8 HEX NYL

WASHER, 1/4 X 5/8 FLAT SS

BRKT, ELECTRICAL

10 86316540

11 86316700

12 86318620

13 86319090

2 CONNECTOR, 5 POS, PUSH WIRE

2 BRKT, CORD STRAIN RELIEF

2 CORD ASM, 14/3 SJT X 25' BLK

2 FUSE HOLDER, PANEL MNT

SERIAL NO.

FROM

NOTES

1 REQ. FOR 3-STAGE

VACUUM MACHINES

1 REQ. FOR 3-STAGE

VACUUM MACHINES

MACHINES WITH

HEAT ONLY

14 86319100 -

15 86364350 -

16 86005810 57245

17 86323330 -

18 86198460 20008

19 86006590 70088

1 FUSE, 1/4" X 1 1/4", 15A

1 FUSE, 7A 1/4" X 1 1/4"

2 NUT, 1/4-20 NYLOCK

2 WASHER, 1/4" ID X 1.0D FLAT BLK

1 CLAMP, 5/8 NYLON UL/CSA

1 SCREW, 10-32 X 1/2 PPHMS SS NP

86322410 NINJA WARRIOR 500 PSI 27

Frame

28 86322410 NINJA WARRIOR 500 PSI

Frame

REF PART NO.

PRV NO.

QTY

86199430

86001660

86005810

86276080

86010630

86005700

86010730

86300070

9 86309790

10 86312830

11 86277500

040-03

41236

57245

70595

87013

57104

87088

70853

DESCRIPTION

2 CASTER, SWIVEL 4" 250# CPCTY

2 HUBCAP, 5/8 SHAFT

8 NUT, 1/4-20 HEX NYLOCK SS

1 SCR, 10-32 X 1” PPHMS GRN

8 WASHER, 1/4 X 5/8 FLAT SS

2 NUT, 10-32 HEX W/STAR

4 WASHER, 5/8 X 1-3/16 FLAT SS

2 HUBCAP, 9.75" WHEEL

2 WHEEL, 12" X 2.25”

1 FRAME, 5/8" AXLE, DUAL VAC

8 SCR,1/4-20 X 5/8 CARR SS

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 29

Heater

13 15

TO CONSOLE SOLUTION

FROM PUMP

86322410 NINJA WARRIOR 500 PSI

Heater

REF PART NO.

PRV NO.

QTY

86200260 151-50C

86197360 31016

86005810

86273830

57245

70020

86233410

86010630

86318310

86318410

81270

87013

9 86318750

10 86006180

66095

11 86199980 130-14

12 86201790 130-14C

13 86200870 300-06A

14 86010650 87018

15 86266020 76029L

16 86266130 76044L

17 86317510

18 86317730 -

19 86326680 -

20 86202220 390-01

DESCRIPTION

1 HOSE,PULSE 47.0 1/4MPTX1/4MPT

2 ELBOW, 1/4 NPT STREET

1 NUT, 1/4-20 HEX NYLOCK SS

2 SCR, 1/4-20 X 1/2 HHCS SS

2 CLAMP, 3/4 DIA CUSHION .406 DIA

3 WASHER, 1/4 X 5/8 FLAT SS

2 CLAMP, 3.25 WORM GEAR SS

1 BRKT, HEATER MOUNT

1 HEATER ASM, 1850W, 120V

1 PLUG, 1/8 MPT HEX BRASS

1 CARTRIDGE HEATER, 5/8" X 10"

1 THERMOSTAT RESET 302

7 SCR, 6 X 3/16, PHSMS, B

3 WASHER, #10 X 9/16 FLAT

1 TERM, 14GA. .25 FEMALE

1 TERM, 14GA. MALE COUPLER FI

1 THERMOSTAT W/VERT SPADE

1 INSULATION, HEATER

1 HEATER CART. CASE WELDED

4 WASHER #5 SS .135ID X .312 OD

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 31

Labels

32 86322410 NINJA WARRIOR 500 PSI

Labels

REF PART NO.

PRV NO.

QTY

1 86318260

2 86318270

3A 86318280

3B 86318290

DESCRIPTION

1 LABEL, NINJA, WARRIOR, LH

1 LABEL, NINJA, WARRIOR, RH

1 LABEL, NINJA, WARRIOR, W/ HEAT

1 LABEL, NINJA, WARRIOR, W/O HEAT

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 33

Pump

TO PRESSURE GAUGE

TO SOLUTION TANK

FROM SOLUTION TANK

86322410 NINJA WARRIOR 500 PSI

Pump

REF PART NO.

PRV NO.

QTY DESCRIPTION

86190520 11-800224 2 PLUG, 3/8 SOCHD BR

86200260 151-50C 2 HOSE,PULSE 47.0 1/4MPT X 1/4MPT

OPEN

86197270

OPEN

04008

OPEN

ADPTR, 1/4MPT X 1/4FPT BR

86197290

86233150

86197360

86197420

14076

20042

31016

31026

BUSHING, 3/8 MPT X 1/4 FPT HEX

CLAMP, 3/8 WORM GEAR

ELBOW, 1/4 NPT STREET

ELBOW, 3/8NPT STREET

9 86282320

10 86240500

11 86270960

12 86274750

13 86197760

14 86233410

15 86010630

16 86317550

39710

40095

57080

70270

78308

81270

87013

HOSE, 1/2ID WIRE BOUND X 26”

HOSEBARB, 3/8MPT X 3/8HOSE 90

NUT, 1/4-20 CAPTIVE

SCR, 1/4-20 X 3/4 HHCS PLTD

TEE, 1/4 STREET

CLAMP, 3/4 DIA CUSHION .406 DIA

WASHER, 1/4 X 5/8 FLAT SS

HOSEBARB, 3/8 MPT X 1/2 90 BR

17 86364370

18 86318990

19 86321290

20 86321470

21 86317590

22 86270850

23 86321660

24 86355740

25 86005710

26 86365240

57026

57105

1 MOTOR, M58 500PSI 120/230V

1 PUMP, SERIES 207V

1 BPR, 500PSI

1 HOSE, 3/8ID WIRE BOUND X 26"

1 HOSE, 10” 1/4JIC X 1/8MPT SS

3 NUT, 8-32 HEX NYLOCK

1 ELBOW, 1/4 MPT X 1/8 FPT

1 BRKT, P/P BPR

1 NUT, 1/4-20 HEX W/STAR WASHER

1 HARNESS, 500PSI PUMP

SERIAL NO.

FROM

*(1)

NOTES

***

* SEE SERIAL NUMBER PAGE

** CALL MANUFACTURER FOR SERIAL NUMBER

*** FOR SERIAL NUMBERS PRIOR TO *(1), USE MOTOR UPGRADE KIT 98411760

86322410 NINJA WARRIOR 500 PSI 35

Pump with Heat

TO HEATER

TO PRESSURE GAUGE

TO SOLUTION TANK

FROM SOLUTION TANK

86322410 NINJA WARRIOR 500 PSI

Pump with Heat

REF PART NO.

PRV NO.

QTY DESCRIPTION

86190520 11-800224 2 PLUG, 3/8 SOCHD BR

86364360 1 HOSE, PULSE 19.5” 1/4MPT X 1/4MPT

OPEN

86197270

OPEN

04008

OPEN

ADPTR, 1/4MPT X 1/4FPT BR

86197290

86233150

86197360

86197420

14076

20042

31016

31026

BUSHING, 3/8 MPT X 1/4 FPT HEX

CLAMP, 3/8 WORM GEAR

ELBOW, 1/4 NPT STREET

ELBOW, 3/8NPT STREET

9 86282320

10 86240500

11 86270960

12 86274750

13 86197760

14 86314700

15 86010630

16 86317550

39710

40095

57080

70270

78308

87013

HOSE, 1/2ID WIRE BOUND X 26”

HOSEBARB, 3/8MPT X 3/8HOSE 90

NUT, 1/4-20 CAPTIVE

SCR, 1/4-20 X 3/4 HHCS PLTD

TEE, 1/4 STREET

CLAMP, CABLE,1-3/4 "P"CUSHION

WASHER, 1/4 X 5/8 FLAT SS

HOSEBARB, 3/8 MPT X 1/2 90 BR

17 86364370

18 86318990

19 86321290

20 86321470

21 86317590

22 86270850

23 86200260

24 86355740

25 86321660

26 OPEN

86006790

86365240

57026

70351

MOTOR, M58 500PSI 120/230V

PUMP, SERIES 207V

BPR, 500PSI

HOSE, 3/8ID WIRE BOUND X 26"

HOSE, 10” 1/4JIC X 1/8MPT SS

NUT, 8-32 HEX NYLOCK

HOSE, PULSE 47.0 1/4MPTX1/4MPT

BRKT, P/P BPR

ELBOW, 1/4 MPT X 1/8 FPT

OPEN

SCREW, 10-32 X .375 SLTDHWH STL

BLKOX

1 HARNESS, 500PSI PUMP

SERIAL NO.

FROM

*(1)

NOTES

***

* SEE SERIAL NUMBER PAGE

** CALL MANUFACTURER FOR SERIAL NUMBER

*** FOR SERIAL NUMBERS PRIOR TO *(1), USE MOTOR UPGRADE KIT 98411760

86322410 NINJA WARRIOR 500 PSI 37

Recovery

10 12

38 86322410 NINJA WARRIOR 500 PSI

Recovery

REF PART NO.

PRV NO.

QTY DESCRIPTION

86161460 15-808123 1 DUMP VALVE, 1 1/2

86002620 260-64A 1 ACCESS, COVER CLEAR 6" W/RIM

86197820

86004000

31002

35255

ELBOW, 1.5 FPT X FS PVC

GASKET, TANK LID

86197040

86273740

86273750

86275800

57264

70010

70011

70546

NUT, 5/16-18 HEX ACORN PLTD

SCR, 1/4-20 X 1.50 HHCS SS

SCR, 1/4-20 X 5/8 HHCS SS

SCR, 8 X 3/4 PFHT/S BLK ZINC

9 86010630

10 86010670

11 86323330

12 86011020

87013

87029

89202

13 86001350 140390

14 86311510 -

15 86312360

16 86313040

17 86316710

18 86317230

19 86317720

20 86320790

21 86233120

20019

WASHER, 1/4 X 5/8 FLAT SS

WASHER, 5/16 X 3/4 SS

WASHER, 1/4 ID X 1.0 OD FLAT BLK

WHEEL, 3" DIA. CUSHION RUBBER

BUSHING, SPANNER .435 X 1.10

ADAPTER, FLOAT 30 DEG, 2

TANK, RECOVERY, TRIMMED

SCRN, FLOAT, SHTOFF, 2

BRKT, CORD, MOUNT

HOSEBARB,1.5MPT X 1.5 W/FLNG

SCR, 5/16-18 X 2.50 BSHCS SS

PIPE ASM, 2", VACUUM

CLAMP, 2.75" WORM GEAR

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 39

Solution

40 86322410 NINJA WARRIOR 500 PSI

Solution

REF PART NO.

PRV NO.

QTY DESCRIPTION

1 86173640 11-800437 2 ADPT,3/8 BLKHD

2 86233150 20042 2 CLAMP, 3/8 WORM GEAR

3 86238460

4 86317550

36259

HOOK, STRAP

HOSEBARB, 3/8 MPT X 1/2 90 BR

5 86001550

6 86273740

7 86273830

8 86005810

40043

70010

70020

57245

HOSEBARB, 3/8 MPT X 3/8 HOSE 90°

SCR, 1/4-20 X 1.50 HHCS SS

SCR, 1/4-20 X 1/2 HHCS SS

NUT, 1/4-20 HEX NYLOCK SS

9 86324210

10 86276160

11 86007970

12 86233410

13 86010670

14 86010630

15 86323330

16 86311990

70604

73864

81270

87029

87013

SCR, 1/4-20 X 5/8 BHCS BLK

SCR, 10-32 X 5/8 PPHMS BLK

STRAINER, 3/8 IN. NPT 60 MESH

CLAMP, 3/4 DIA CUSHION .406 DIA

WASHER, 5/16 X 3/4 SS

WASHER, 1/4 X 5/8 FLAT SS

WASHER, 1/4 ID X 1.0 OD FLAT BLK

HINGE, 9.5" LG X .074 THK

17 86312000

18 86312010

19 86312350

20 86297620

21 86317560

22 86318790

23 86242130

24 86324030

48100

1 LID, SOLUTION, COVER

1 LID, SOLUTION, HINGE BRKT

1 TANK, SOL, TRIM

2 STRAP, HAND TOOL

1 SPACER, .50 ODX .28 ID X 1.0L

2 WASHER, 1.032ID X 1.5OD X .062THK

2 KNOB, 1/4 HEX PRESS-LOC WING

2 PLATE, MOUNTING, SOLUTION

SERIAL NO.

FROM

NOTES

COMPLETE

86322410 NINJA WARRIOR 500 PSI 41

Vacuum, 2-Stage / 3-Stage

13A

13B

11A

11B

86322410 NINJA WARRIOR 500 PSI

Vacuum, 2-Stage / 3-Stage

REF PART NO. PRV NO.

QTY DESCRIPTION

1 86005810

2 86274090

3 86233430

4 86010630

5 86278990

6 86311520

7 86312990

8A 86314710

57245

70092

81431

87013

87017

8 NUT, 1/4-20 HEX NYLOCK SS

5 SCR, 10-32 X 1.5 PPHMS

2 CLAMP, 2.50 WORM GEAR

16 WASHER, 1/4 X 5/8 FLAT SS

8 WASHER, #8 X 3/8 FLAT

1 MANIFOLD, VACUUM, DUAL

1 GASKET, VAC MANIFOLD, DUAL

8 SCR, 1/4-20 X 5.50 HHCS PLT

8B 86277840 00-000167 8 SCR, 1/4-20 X 6.5 HHCS PLT

9 86317630 8 SCR, #8 X 3/4" PPHSMS TYPE AB

10 86318300

11A 86318760

HOSE, VAC, 2.0 ID X 18.5"L

VAC ASM, 2-STAGE, 120V

11B 86318770 -

86135320 140687

12 86312080

13A 86312220

VAC ASM, 3-STAGE, 120V

SP BRUSHES SET (120V VAC)

COVER, VAC MOTOR

BASE, VAC MOTOR, 2-STAGE

13B 86312120

86319020

86319030

2 BASE, VAC MOTOR, 3-STAGE

VAC HOUSING, 2-STAGE

VAC HOUSING, 3-STAGE

SERIAL NO.

FROM

NOTES

2-STAGE

3-STAGE

INCLUDES 12, 13A

INCLUDES 12, 13B

86322410 NINJA WARRIOR 500 PSI 43

Wiring - 2 Stage Vacuum

-VACUUM

SWITCH

-PANEL

-VACUUM

SWITCH

-PUMP

SWITCH

-POWER

CORD

BLK

-FUSE

7AMP

GRY-WHT

GRN

WHT

BLK

-TERMINAL

BLOCK

BLK-WHT

-CB

13AMP

-CB

13AMP

BLU/1 BLU-BLK/2 GRY/3

GRN

WHT

WHT FROM PUMP

-VACUUM

MOTOR

GRN

WHT/7

-VACUUM

MOTOR

WHT/8 WHT

BLK

-PUMP

MOTOR

GRN GRN

44 86322410 NINJA WARRIOR 500 PSI

REF PART NO.

PRV NO.

QTY

1 98407900 1

DESCRIPTION

HARNESS KIT, SINGLE CORD

Wiring - 2 Stage Vacuum

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 45

Wiring - 3 Stage Vacuum

-POWER

CORD

-POWER

CORD

-VACUUM

SWITCH

-PANEL

-VACUUM

SWITCH

-PUMP

SWITCH

MOTOR MOTOR MOTOR

46 86322410 NINJA WARRIOR 500 PSI

REF PART NO.

PRV NO.

QTY

1 98407910 1

DESCRIPTION

HARNESS KIT, DUAL CORD

Wiring - 3 Stage Vacuum

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 47

Wiring with Heat

-FUSE

7AMP

BLK

WHT

48 86322410 NINJA WARRIOR 500 PSI

REF PART NO.

PRV NO.

QTY

1 98407920 1

DESCRIPTION

HARNESS KIT, HEATED

Wiring with Heat

SERIAL NO.

FROM

NOTES

86322410 NINJA WARRIOR 500 PSI 49

Suggested Spare Parts

PART NO.

PRV NO.

DESCRIPTION

86199240 250-33A BPR REPAIR KIT PUMPTEC

86317510 THERMOSTAT W/ VERT SPADE

86201790 130-14C THERMOSTAT RESET 302

86135320 140687 BRUSH SET, 120V VAC

86199430 040-03 CASTER SWIVEL 4” 250# CAPACITY

86002620 260-64A ACCESS COVER CLEAR 6” W/RIM

86364350

86319100

FUSE, 7A 1/4" X 1 1/4"

FUSE, 1/4” X 1-1/4”, 15A

86318760

86318770

86007140

86317850

VAC ASSY 2-STG, 120V

VAC ASSY 3-STG, 120V

72130 SWITCH, SPST 2-POSITION ROCKER

SWITCH, LIGHTED 2-POSITION ROCKER

86309790

86001660

WHEEL, 12” X 2.25”

41236 HUBCAP, 5/8” SHAFT

86007970 73864 STRAINER 3/8” NPT 60 MESH

86201040 250-73C CAM & BEARING KIT

86201080 250-75A PLUNGER & SEALS KIT

86201030 250-73B VALVE & O RINGS KIT

86324290

86006350

86357300

67029

PRIMING HOSE

RECTIFIER, BRIDGE

TERMINAL STRIP, 12 POST IDEAL

SERIAL NO.

FROM

NOTES

(HEATED MODELS)

(2-STG MODELS)

(3-STG MODELS)

(HEATED MODELS)

CUT TO FIT

50 86322410 NINJA WARRIOR 500 PSI

REF.

NO.

1.007-062.0 - 10070620000086

1.007-068.0 - 10070680001708

1.007-069.0 - 10070690000137

MODEL: SERIAL #

Serial Numbers

86322410 NINJA WARRIOR 500 PSI 51

Notes:

52 86322410 NINJA WARRIOR 500 PSI

New Machine Warranty

Limited Warranty

CENTURY 400

warrants new machines against defects in material and workmanship under normal use and service to the original purchaser. Any statutory implied warranties, including any warranty of merchantability or fitness for a particular purpose, are expressly limited to the duration of this written warranty. CENTURY 400 will not be liable for any other damages, including but not limited to indirect or special consequential damages arising out of or in connection with the furnishing, performance, use or inability to use the machine. This remedy shall be the exclusive remedy of the buyer. The warranty period is subject to the conditions stated below.

Warranty: Ten Years Polyethylene (PE) Housings, 1 Year Parts,

Subject to conditions outlined below, CENTURY 400 warrants rotationally molded PE housings on all of its machines to be free from defects in material and workmanship, under normal use and service for ten (10) years to the original owner.

Under this warranty we guarantee the performance of non-polyethylene parts and components to be free from defects for up to one (1) year to the original end user. Parts replaced or repaired under this warranty are guaranteed for the remainder of the original warranty period. (See table below)

Service labor charges are covered for up to ninety (90) days from the date of purchase through authorized Windsor service provider.

No travel coverage is extended for cord-electric models. See table below for each general product model warranty coverage.

Non-PE Parts Service Labor Travel

Ninja, Sensei, Spot Plus,

Hurricane and Turbo Mist

10 years 1 year 90 days None

Polishers / Elec. Burnishers - 3 years 90 days None

All others

UPV12 Upright Vacuum

5 years

Vacuum motor, belts – 2 years

1 year

All other parts 1 year

90 days

None

Product exceptions and Exclusions:

• Extractor brush motors, pump motors. ALL PC boards and electronics, ALL Vacuum motors (Except UPV12). ALL pumps carry a one (1) year parts warranty.

• Improper use of chemicals voids warranty and Century 400’s liability. Defoamer is to be used in recovery tank of all Century 400 machines. Dry cleaning solvents cannot be used in any Century 400 equipment, if used fire and/or pump damage could result.

White vinegar should be pumped through the machine once each week to prevent mineral sealing.

Normal wear items and accessories including, but not limited to, carbon brushes, castors, clutches, cords, filters, finishes, gaskets, hoses light bulbs, rectifiers, switches, squeegees, bearings, pulleys, relays, actuating cables, wheels, tires, quick disconnects, o-rings, seals, diaphragms, thermostats, and brass fittings will be warranted for manufacturing defects for 90-days from the purchase date for parts only.

90 day unlimited warranty :

Any equipment that fails due to a manufacturing defect within the first 90 days from date of purchase will have an unlimited warranty, which includes parts, standard freight, and labor. Labor or freight will not be covered after 90 days from the date of purchase.

The warranty commences on the purchase date by the original end user from an authorized Century 400 agent, subject to proof of purchase. The machine Registration Card must be completed and returned immediately at the time of purchase. If proof of purchase cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Century 400 distributor. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period.

Century 400

, reserves the right to change its warranty policy without notice – 86039960-B PRV NO 98868 10/17/08

Century 400 Inc

. ● 1351 W. Stanford Ave., Englewood, CO 80110 ● (303) 762-1800 ● 800-444-7654 ● FAX (303) 865-2794

1 of 2

New Machine Warranty

90 Day Warranty Extension Available

Upon receipt of the Machine Registration Card, Century 400 will extend by 90 days, from the date of purchase, all items included under the one-year provision. This applies only to one-year items and does not include 90-day wear items.

This Warranty Shall Not Apply To:

Any product that has been subject to abuse, misuse, neglect or unauthorized alteration (including the use of incompatible or corrosive chemicals or overloading of capacity).

Damage caused by exposure to freezing temperatures.

Products that have experienced shipping or freight damage.

Repairs necessary to correct any failure due to improper pre-delivery service and inspection by the selling dealer.

Time for cleaning units in preparation for repair.

Any repairs resulting from poor initial service work or improper diagnosis.

Any design alterations performed by an organization not authorized or specified by CENTURY 400.

High-pressure washing.

Damage due to electrical components exposed to moisture.

If difficulty develops during the warranty period, contact the authorized CENTURY 400 agent from whom the product was purchased.

CENTURY 400 may elect to require the return of components to validate a claim. Any defective part to be returned must be shipped freight prepaid to an authorized CENTURY 400 Distributor/Service Center or to the CENTURY 400 factory.

Use of Parts Not Approved By Century 400 Will Void All Warranties

This warranty is valid only for all products sold after October 17, 2008. A product sold before that date shall be covered by the limited warranty in effect at the date of sale to the original purchaser.

Century 400

, reserves the right to change its warranty policy without notice – 86039960-B PRV NO 98868 10/17/08

Century 400 Inc

. ● 1351 W. Stanford Ave., Englewood, CO 80110 ● (303) 762-1800 ● 800-444-7654 ● FAX (303) 865-2794

2 of 2

Hello! I am an AI chatbot specifically trained to assist you with the Century 400 NINJA Warrior NWCU2350N Operating Instructions Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.