cover page for test report

cover page for test report
Issue Date:
2005-08-06
Page 1 of 1
Report Reference #
E137006-A6-CB-1
COVER PAGE FOR TEST REPORT
Test Item Description:
Model/Type Reference:
Rating(s):
Standards:
Applicant Name and
Address:
Factory Location(s):
DIN-Rail Switch Mode Power Supply
QS10.XXZ.ZZ, where XX represents the output voltage and can be 12 to 15 or
24 to 28 or 48 to 56 or DNET, Z can be any number.
Model QS10.XXZ.ZZ:
Input: 100-240Vac, 50-60Hz, 1.2-2.8A; 110-300Vdc, 0.9-2.4A;
Output:
where XX can be 12-15: Output: 12-15V, 15-13.5A
where XX can be 24-28: Output: 24-28V, 10-9A, 252W;
where XX can be 48-56: Output: 48-56V, 5.0-4.3A, 240W;
where XX can be DNET: Output: 24-24.5V, 8A
IEC 60950-1:2001, First Edition
PULS ELEKTRONISCHE STROMVERSORGUNGEN
GMBH
ARABELLASTR 15
81925 MUNICH GERMANY
PULS EP K.S.
UL. ALFONSE MUCHY 5473
430 01 CHOMUTOV, CZECH REPUBLIC
This Report includes the following parts, in addition to this cover page:
1. Specific Technical Criteria
2. Clause Verdicts
3. Critical Components
4. Test Results
5. Enclosures
a. National Differences
b. Photographs
c. Diagrams
d. Schematics + PWB
e. Licenses
All applicable tests according to the above standard(s) have been carried out.
Test results are valid only for the tested equipment.
This Test Report can be reproduced only in whole.
Amendments and corrections can be reproduced only with the original CB Test Report.
Written permission from UL International Demko A/S is required if the test report is copied in part.
Copyright © 2002UL International Demko A/S
Issue Date:
2005-08-06
Page 1 of 58
Report Reference #
E137006-A6-CB-1
TEST REPORT
IEC 60950-1, First Edition
Information technology equipment - Safety Part 1: General Requirements
Report Reference No .....................: E137006-A6-CB-1
Tested by (+ signature).....................: Thomas Weißbach
Authorized by (+ signature)...............: Michaela Zielke
Supervised by (+ signature )
Paul Zawatson
Date of issue .....................................: 2005-08-06
CB Testing Laboratory ...................: UL International Demko A/S
Address .............................................: Lyskaer 8, 2730, Herlev, Denmark
Testing location/procedure ...............: CBTL [ ]
SMT [x]
TMP [ ]
WMT [ ]
Address .............................................: PULS ELEKTRONIK, GMBH, Niederwaldstraße 3, D-09123
Chemnitz, Germany
Applicant's name ...........................: PULS ELEKTRONISCHE STROMVERSORGUNGEN
GMBH
Address ............................................: ARABELLASTR 15
81925 MUNICH GERMANY
Test specification:
Standard ..........................................: IEC 60950-1:2001, First Edition
Test procedure
:
CB Scheme
Non-standard test method ...............: N/A
Test Report Form No. .......................: IEC60950__1A
TRF originator ..................................: SGS Fimko Ltd
Master TRF ......................................: dated 2002-03
Copyright © 2003 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the
IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for
and will not assume liability for damages resulting from the reader's interpretation of the reproduced material
due to its placement and context.
Test item description .......................: DIN-Rail Switch Mode Power Supply
Trade Mark .......................................: None
Model/Type reference
:
QS10.XXZ.ZZ, where XX represents the output voltage and can be
12 to 15 or 24 to 28 or 48 to 56 or DNET, Z can be any number.
Manufacturer ....................................: PULS ELEKTRONIK, GMBH, Niederwaldstraße 3, D-09123
Chemnitz, Germany
Rating ...............................................: Input:
100-240Vac, 50-60Hz, 1.2-2.8A; 110-300Vdc, 0.9-2.4A;
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 2 of 58
Report Reference #
E137006-A6-CB-1
Output:
where XX can be 12-15: Output: 12-15V, 15-13.5A
where XX can be 24-28: Output: 24-28V, 10-9A, 252W;
where XX can be 48-56: Output: 48-56V, 5.0-4.3A, 240W;
where XX can be DNET: Output: 24-24.5V, 8A
Marking Plate - Refer to Enclosure titled Miscellaneous for copy.
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 3 of 58
Report Reference #
E137006-A6-CB-1
Particulars: test item vs. test requirements
Equipment mobility :
for building-in
Operating condition :
continuous
Mains supply tolerance (%)
:
+-15%
Tested for IT power systems
:
Yes
IT testing, phase-phase voltage (V)
:
240
Class of equipment :
Mass of equipment (kg)
Class I (earthed)
:
Protection against ingress of water
0.9kg
:
IP X0
Possible test case verdicts:
- test case does not apply to the test object
:
- test object does meet the requirement :
- test object does not meet the requirement
N/A
P(Pass)
:
F(Fail)
General remarks:
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by a NCB in accordance with IECEE 02.
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 4 of 58
Report Reference #
E137006-A6-CB-1
General Product Information:
Report Summary
All applicable tests according to the referenced standard(s) have been carried out.
Product Description
The product is a Switch Mode Power Supply for DIN-Rail mounting.
Model Differences
Models are technical identical, except for the differences outlined below:
Number: QS10.XXZ.ZZ, where XX can be 24-28;
Trafo: TE-339.590.00
Output capacitor (C13, C14): 3900µ/35V
Output capacitor (C501): 580µ/35V oder 680µ/35V
Inductor (L501, L502): LB-192.540.00
Rectifier (V15): MOSFET 60V/0R0052
Overvoltage Protection: Primary only
QS10.241-70 is identical to basic model QS10.XXZ.ZZ except different terminals
Number: QS10.DNET;
Trafo: TE-339.590.00
Output capacitor (C13, C14): 3900µ/35V
Output capacitor (C501): 580µ/35V oder 680µ/35V
Inductor (L501, L502): LB-192.540.00
Rectifier (V15): MOSFET 60V/0R0052
Overvoltage Protection: Primary only
Number: QS10.XXZ.ZZ, where XX can be 48-56;
Trafo: TE-339.590.05
Output capacitor (C13, C14): 1500µ/63V
Output capacitor (C501): 330µ/63V
Inductor (L501, L502): LB-192.550.00
Rectifier (V15): Diode 10A/150V
Overvoltage Protection: Opto (U4) and (N103)
Number: QS10.XXZ.ZZ, where XX can be 12–15;
Trafo: TE-339.590.02
Output circuit (Rectifier, Output capacitor)
Output power reduction
Additional Information
The load conditions have been as follows:
Condition A: 24Vdc, 10.0A;
Condition B: 28Vdc, 9.0A;
Condition C: 48Vdc, 5.0A;
Condition D: 48Vdc, 4.3A;
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 5 of 58
Report Reference #
E137006-A6-CB-1
12V-15V model:
Condition A: 12 Vdc, 15A;
Condition B: 15 Vdc, 13.5A
Technical Considerations
The product was submitted and tested for use at the maximum ambient temperature (Tma) permitted by the
manufacturer’s specification of: 60°C. 12V model up to 70°C with 75% rated load
The means of connection to the mains supply is: Permanently connected (field wired)
The product is intended for use on the following power systems: TT, TN, IT, DC mains supply
Models: AN-339.100.00 and AN-399.100.05 have been tested with a power boost of 360W for 4sec at a duty
cycle of 0.044.
The normal mouting orientation is: Input downwards, output upwards. Other mounting orientations have been
measured at a lower output current of 60%. Refer to heating test table for details.
Engineering Conditions of Acceptability
When installed in an end-product, consideration must be given to the following:
The following Production-Line tests are conducted for this product: Electric Strength, Earthing Continuity
The end-product Electric Strength Test is to be based upon a maximum working voltage of: Primary-SELV:
209Vrms, 482Vpk; Primary-Earthed Metal: 300Vrms, 354Vpk;
The following secondary output circuits are SELV: All outputs.
The following secondary output circuits are at hazardous energy levels: Power Output.
The power supply terminals and/or connectors are: Suitable for field wiring
The maximum investigated branch circuit rating is: 20 A (15A Europe)
The investigated Pollution Degree is: 2
Proper bonding to the end-product main protective earthing termination is: Required, at housing earthing bolt.
An investigation of the protective bonding terminals has: Not been conducted
The following magnetic devices (e.g. transformers or inductor) are provided with an OBJY2 insulation system
with the indicated rating greater than Class A (105°C): T1 (Class F)
The following end-product enclosures are required: Fire, Electrical
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 6 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
1
GENERAL
Pass
1.5
Components
Pass
1.5.1
General
Pass
Comply with IEC 60950 or relevant component
standard
Pass
1.5.2
Evaluation and testing of components
Pass
1.5.3
Thermal controls
N/A
1.5.4
Transformers
1.5.5
Interconnecting cables
1.5.6
Capacitors in primary circuits:
1.5.7
Double insulation or reinforced insulation bridged
by components
N/A
1.5.7.1
General
N/A
1.5.7.2
Bridging capacitors
N/A
1.5.7.3
Bridging resistors
N/A
1.5.7.4
Accessible parts
N/A
1.5.8
Components in equipment for IT power systems
1.6
Power interface
Pass
1.6.1
AC power distribution systems
Pass
1.6.2
Input current
Pass
1.6.3
Voltage limit of hand-held equipment
N/A
1.6.4
Neutral conductor
Pass
TRF No.: IEC60950__1A
Result - Remark
T1
Verdict
Pass
N/A
X-Caps: C505, C1, C40;
Y-Caps: C506-C508;
Capacitors rated min. 300Vac.
UL International Demko A/S
Pass
Pass
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 7 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
1.7
Marking and instructions
Pass
1.7.1
Power rating
Pass
Rated voltage(s) or voltage range(s) (V):
Refer to Cover Page.
Verdict
Pass
Symbol for nature of supply, for o.k. Only:
N/A
Rated frequency or rated frequency range (Hz).... : Refer to Cover Page.
Pass
Rated current (mA or A) ........................................ : Refer to Cover Page.
Pass
Manufacturer's name or trademark or identification PULS GmbH
mark....................................................................... :
Pass
Type/model or type reference ............................... : Refer to Cover Page.
Pass
Symbol for Class II equipment only....................... :
N/A
Other symbols ....................................................... :
N/A
Certification marks................................................. : UL/c-UL-Recognition
Pass
1.7.2
Safety instructions
N/A
1.7.3
Short duty cycles
N/A
1.7.4
Supply voltage adjustment .................................... : Autoranging
N/A
1.7.5
Power outlets on the equipment............................ :
N/A
1.7.6
Fuse identification.................................................. : F501: Cross-Reference to
Service Manual. See LOCC for
ratings.
Pass
1.7.7
Wiring terminals
Pass
1.7.7.1
Protective earthing and bonding terminals ............ : The earth terminal is marked
with the standard earth symbol
(60417-2-IEC-5019) near the
terminal.
Protective earthing to be
evaluated in the end product.
Pass
1.7.7.2
Terminal for a.c. mains supply conductors
Pass
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
N/A
1.7.8.1
Identification, location and marking ....................... :
N/A
1.7.8.2
Colours .................................................................. :
N/A
1.7.8.3
Symbols according to IEC 60417 .......................... :
N/A
1.7.8.4
Markings using figures........................................... :
N/A
TRF No.: IEC60950__1A
Marked "L" and "N".
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 8 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.7.9
Isolation of multiple power sources ....................... :
N/A
1.7.10
IT power distribution systems
N/A
1.7.11
Thermostats and other regulating devices
N/A
1.7.12
Language............................................................... :
1.7.13
Durability
1.7.14
Removable parts
N/A
1.7.15
Replaceable batteries
N/A
Unit is for building-in. However
markings have been evaluated
for durability.
N/A
Language............................................................... :
-
1.7.16
Operator access with a tool ................................... :
N/A
1.7.17
Equipment for restricted access locations............. :
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 9 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2
PROTECTION FROM HAZARDS
Pass
2.1
Protection from electric shock and energy hazards
Pass
2.1.1
Protection in operator access areas
2.1.1.1
Access to energized parts
N/A
Test by inspection.................................................. :
N/A
Test with test finger ............................................... :
N/A
Test with test pin.................................................... :
N/A
Test with test probe ............................................... :
N/A
2.1.1.2
Battery compartments ........................................... :
N/A
2.1.1.3
Access to ELV wiring
N/A
To be considered in end-use
application.
Working voltage (V); minimum distance (mm)
through insulation .................................................. :
Verdict
N/A
-
2.1.1.4
Access to hazardous voltage circuit wiring
N/A
2.1.1.5
Energy hazards ..................................................... : Power output is considered
hazardous energy. To be
considered in end-use
application.
N/A
2.1.1.6
Manual controls
N/A
2.1.1.7
Discharge of capacitors in equipment
Pass
Time-constant (s); measured voltage (V) .............. : Time constant less than 1
second.
-
2.1.2
Protection in service access areas
N/A
2.1.3
Protection in restricted access locations
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 10 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
2.2
SELV circuits
Pass
2.2.1
General requirements
Pass
2.2.2
Voltages under normal conditions (V) ................... : All accessible voltages are
less than 42.4 Vp or 60 V dc
and are classified as SELV.
Pass
2.2.3
Voltages under fault conditions (V) ....................... : Under fault conditions voltages
never exceed 71V peak and
120Vdc and do not exceed
42.4V peak or 60V dc for more
than 0.2 sec.
Pass
2.2.3.1
Separation by double insulation or reinforced
insulation (method 1)
Pass
2.2.3.2
Separation by earthed screen (method 2)
N/A
2.2.3.3
Protection by earthing of the SELV circuit (method
3)
N/A
2.2.4
Connection of SELV circuits to other circuits ........ : The SELV circuits are not
connected to other circuits
other than protective earth.
Pass
2.3
TNV circuits
N/A
2.3.1
Limits
N/A
2.3.2
2.3.3
Result - Remark
Type of TNV circuits .............................................. :
-
Separation from other circuits and from accessible
parts
N/A
Insulation employed............................................... :
-
Separation from hazardous voltages
Insulation employed............................................... :
2.3.4
Connection of TNV circuits to other circuits
Insulation employed............................................... :
2.3.5
Verdict
Test for operating voltages generated externally
TRF No.: IEC60950__1A
UL International Demko A/S
N/A
N/A
N/A
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 11 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.4
Limited current circuits
N/A
2.4.1
General requirements
N/A
2.4.2
Limit values
N/A
Frequency (Hz)...................................................... :
-
Measured current (mA).......................................... :
-
Measured voltage (V) ............................................ :
-
Measured capacitance (mF).................................. :
-
2.4.3
Connection of limited current circuits to other
circuits
N/A
2.5
Limited power sources
N/A
Inherently limited output
N/A
Impedance limited output
N/A
Overcurrent protective device limited output
N/A
Regulating network limited output under normal
operating and single fault condition
N/A
Regulating network limited output under normal
operating conditions and overcurrent protective
device limited output under single fault condition
N/A
Output voltage (V), output current (A), apparent
power (VA):............................................................ :
-
Current rating of overcurrent protective device (A) :
-
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 12 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.6
Provisions for earthing and bonding
2.6.1
Protective earthing
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
Pass
2.6.3.1
General
2.6.3.2
Size of protective earthing conductors
Pass
Unit is for building-in.
Equipment shall be properly
bonded over earthing bolt at
chassis.
N/A
Pass
N/A
Rated current (A), cross-sectional area (mm2),
AWG ...................................................................... :
2.6.3.3
Verdict
-
Size of protective bonding conductors
N/A
Rated current (A), cross-sectional area (mm2),
AWG ...................................................................... :
-
2.6.3.4
Resistance (Ohm) of earthing conductors and their 1 mOhm, test done with 40A
terminations, test current (A) ................................. : for 2min from PE input terminal
to screw at housing;
Additionally 30A, 2min test
was conducted for PE trace
over L503 with max. resistance
of 0.05Ohm.
Pass
2.6.3.5
Colour of insulation................................................ : No wiring used.
N/A
2.6.4
Terminals
Pass
2.6.4.1
General
Pass
2.6.4.2
Protective earthing and bonding terminals
Pass
Rated current (A), type and nominal thread
M4 used at housing.
diameter (mm) ....................................................... :
-
2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
Pass
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
Pass
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 13 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.6.5.6
Corrosion resistance
Pass
2.6.5.7
Screws for protective bonding
Pass
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
Pass
2.7.1
Basic requirements
Pass
DC Fuse test conducted.
Instructions when protection relies on building
installation
Verdict
N/A
2.7.2
Faults not covered in 5.3
2.7.3
Short-circuit backup protection
Pass
2.7.4
Number and location of protective devices ........... : F501 located in phase.
Pass
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ................................ :
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ................................................ :
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
TRF No.: IEC60950__1A
Exception not used.
UL International Demko A/S
N/A
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 14 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
2.9
Electrical insulation
Pass
2.9.1
Properties of insulating materials
Pass
2.9.2
Humidity conditioning
2.9.3
Result - Remark
96h
Verdict
Pass
Humidity (%) .......................................................... : 94
-
Temperature (°C)................................................... : 29
-
Grade of insulation
TRF No.: IEC60950__1A
Pass
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 15 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.10
Clearances, creepage distances and distances through insulation
Pass
2.10.1
General
Pass
2.10.2
Determination of working voltage
Pass
2.10.3
Clearances
Pass
2.10.3.1
General
Pass
2.10.3.2
Clearances in primary circuit
Pass
2.10.3.3
Clearances in secondary circuits
Pass
2.10.3.4
Measurement of transient voltage levels
N/A
2.10.4
Creepage distances
Pass
CTI tests ................................................................ :
Verdict
-
2.10.5
Solid insulation
Pass
2.10.5.1
Minimum distance through insulation
N/A
2.10.5.2
Thin sheet material
Pass
2.10.5.3
Number of layers (pcs) .......................................... : min. 3 layer
-
Electric strength test .............................................. : 3000Vac / one layer
-
Printed boards
Pass
Distance through insulation
Pass
Electric strength test for thin sheet insulating
material .................................................................. :
-
Number of layers (pcs) .......................................... :
N/A
Wound components
N/A
Number of layers (pcs) .......................................... :
N/A
Two wires in contact inside wound component;
angle between 45° and 90° ................................... :
N/A
2.10.6
Coated printed boards
N/A
2.10.6.1
General
N/A
2.10.6.2
Sample preparation and preliminary inspection
N/A
2.10.6.3
Thermal cycling
N/A
2.10.6.4
Thermal ageing (°C) .............................................. :
N/A
2.10.6.5
Electric strength test .............................................. :
-
2.10.6.6
Abrasion resistance test
2.10.5.4
TRF No.: IEC60950__1A
N/A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 16 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
2.10.7
2.10.8
Requirement + Test
Result - Remark
Verdict
Electric strength test .............................................. :
-
Enclosed and sealed parts .................................... :
N/A
Temperature T1=T2 = Tma - Tamb +10K (°C)...... :
N/A
Spacings filled by insulating compound ................ :
N/A
Electric strength test .............................................. :
-
2.10.9
Component external terminations
Pass
2.10.10
Insulation with varying dimensions
N/A
3
WIRING, CONNECTIONS AND SUPPLY
Pass
3.1
General
Pass
3.1.1
Current rating and overcurrent protection
3.1.2
Protection against mechanical damage
3.1.3
Securing of internal wiring
3.1.4
Insulation of conductors
N/A
3.1.5
Beads and ceramic insulators
N/A
3.1.6
Screws for electrical contact pressure
N/A
3.1.7
Insulating materials in electrical connections
N/A
3.1.8
Self-tapping and spaced thread screws
3.1.9
Termination of conductors
N/A
10 N pull test
N/A
Sleeving on wiring
N/A
3.1.10
TRF No.: IEC60950__1A
To be considered in end-use
product.
N/A
N/A
Only PWB connections.
Min. 2 threads provided.
UL International Demko A/S
N/A
Pass
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 17 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
3.2
Connection to an a.c. mains supply or a d.c. mains supply
N/A
3.2.1
Means of connection
N/A
3.2.1.1
Connection to an a.c. mains supply
N/A
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
N/A
Number of conductors, diameter (mm) of cable and
conduits ................................................................. :
Verdict
-
3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A
Type....................................................................... :
-
Rated current (A), cross-sectional area (mm²),
AWG ...................................................................... :
-
3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ........................... :
-
Longitudinal displacement (mm) ........................... :
-
3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
3.2.9
D (mm); test mass (g)............................................ :
-
Radius of curvature of cord (mm).......................... :
-
Supply wiring space
TRF No.: IEC60950__1A
N/A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 18 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
Rated current (A), cord/cable type, cross-sectional
area (mm²) ............................................................. :
3.3.5
Wiring terminal sizes
Verdict
N/A
Rated current (A), type and nominal thread
diameter (mm) ....................................................... :
-
3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
N/A
3.4.1
General requirement
N/A
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Single-phase equipment and d.c. equipment
N/A
3.4.7
Three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 19 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
3.5
Interconnection of equipment
N/A
3.5.1
General requirements
N/A
3.5.2
Types of interconnection circuits ........................... :
N/A
3.5.3
ELV circuits as interconnection circuits
N/A
4
PHYSICAL REQUIREMENTS
Pass
4.1
Stability
N/A
Angle of 10°
N/A
Test: force (N)........................................................ :
N/A
4.2
Mechanical strength
Pass
4.2.1
General
Pass
4.2.2
Steady force test, 10 N
No terminations or
components in question.
N/A
4.2.3
Steady force test, 30 N
Tested by inspection.
Pass
4.2.4
Steady force test, 250 N
N/A
4.2.5
Impact test
N/A
Fall test
N/A
Swing test
N/A
4.2.6
Drop test
N/A
4.2.7
Stress relief test
N/A
4.2.8
Cathode ray tubes
N/A
Picture tube separately certified ............................ :
N/A
4.2.9
High pressure lamps
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ....... :
N/A
TRF No.: IEC60950__1A
Result - Remark
UL International Demko A/S
Verdict
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 20 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
4.3
Design and construction
Pass
4.3.1
Edges and corners
Pass
4.3.2
Handles and manual controls; force (N)................ :
N/A
4.3.3
Adjustable controls
4.3.4
Securing of parts
N/A
4.3.5
Connection of plugs and sockets
N/A
4.3.6
Direct plug-in equipment
N/A
Dimensions (mm) of mains plug for direct plug-in . :
N/A
Torque and pull test of mains plug for direct plug-in;
torque (Nm); pull (N).............................................. :
N/A
4.3.7
Heating elements in earthed equipment
N/A
4.3.8
Batteries
N/A
4.3.9
Oil and grease
N/A
4.3.10
Dust, powders, liquids and gases
N/A
4.3.11
Containers for liquids or gases
N/A
4.3.12
Flammable liquids.................................................. :
N/A
Quantity of liquid (l)................................................ :
N/A
Flash point (°C)...................................................... :
N/A
4.3.13
Radiation; type of radiation
N/A
4.3.13.1
General
Pass
4.3.13.2
Ionizing radiation
N/A
4.3.13.3
Result - Remark
No user adjustable controls.
Verdict
N/A
Measured radiation (pA/kg) ................................... :
-
Measured high-voltage (kV) .................................. :
-
Measured focus voltage (kV)................................. :
-
CRT markings........................................................ :
-
Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification .......................................................... :
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation ....... :
N/A
4.3.13.5
Laser (including LEDs)
TRF No.: IEC60950__1A
Only indication LED's
provided.
UL International Demko A/S
Pass
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 21 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Laser class ............................................................ :
-
4.3.13.6
Other types ............................................................ :
N/A
4.4
Protection against hazardous moving parts
N/A
4.4.1
General
N/A
4.4.2
Protection in operator access areas
N/A
4.4.3
Protection in restricted access locations
N/A
4.4.4
Protection in service access areas
N/A
4.5
Thermal requirements
Pass
4.5.1
Maximum temperatures
Pass
Normal load condition per Annex L ....................... : Rated load used for continious
testing.
N/A
4.5.2
Resistance to abnormal heat
Pass
4.6
Openings in enclosures
N/A
4.6.1
Top and side openings
N/A
Dimensions (mm) .................................................. :
4.6.2
Bottoms of fire enclosures
Construction of the bottom .................................... :
N/A
-
4.6.3
Doors or covers in fire enclosures
N/A
4.6.4
Openings in transportable equipment
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature (°C)/time (weeks) ......... :
TRF No.: IEC60950__1A
UL International Demko A/S
-
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 22 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
4.7
Resistance to fire
Pass
4.7.1
Reducing the risk of ignition and spread of flame
Pass
Method 1, selection and application of components
wiring and materials
Pass
Method 2, application of all of simulated fault
condition tests
N/A
4.7.2
Conditions for a fire enclosure
N/A
4.7.2.1
Parts requiring a fire enclosure
Pass
4.7.2.2
Parts not requiring a fire enclosure
N/A
4.7.3
Materials
Pass
4.7.3.1
General
Pass
4.7.3.2
Materials for fire enclosures
N/A
4.7.3.3
Materials for components and other parts outside
fire enclosures
N/A
4.7.3.4
Materials for components and other parts inside fire
enclosures
Pass
4.7.3.5
Materials for air filter assemblies
N/A
4.7.3.6
Materials used in high-voltage components
N/A
TRF No.: IEC60950__1A
Result - Remark
UL International Demko A/S
Verdict
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 23 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
Pass
5.1
Touch current and protective conductor current
Pass
5.1.1
General
Pass
5.1.2
Equipment under test (EUT)
Pass
5.1.3
Test circuit
Pass
5.1.4
Application of measuring instrument
Pass
5.1.5
Test procedure
Pass
5.1.6
Test measurements
Pass
Test voltage (V) ..................................................... : 276Vac, 50Hz; IT: Phase-ToPhase: 276Vac, 50Hz;
-
Measured touch current (mA)................................ : max. 0.3mA; IT: max. 0.76mA;
-
Max. allowed touch current (mA)........................... : 3.5mA
-
Measured protective conductor current (mA) ........ : N/A
-
Max. allowed protective conductor current (mA) ... : N/A
-
5.1.7
Equipment with touch current exceeding 3.5 mA .. :
N/A
5.1.8
Touch currents to and from telecommunication
networks and cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network and a cable distribution
system
N/A
Test voltage (V) ..................................................... :
-
Measured touch current (mA)................................ :
-
Max. allowed touch current (mA)........................... :
-
5.1.8.2
Summation of touch currents from
telecommunication networks ................................. :
N/A
5.2
Electric strength
Pass
5.2.1
General
Pass
5.2.2
Test procedure
Pass
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 24 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5.3
Abnormal operating and fault conditions
Pass
5.3.1
Protection against overload and abnormal
operation
Pass
5.3.2
Motors
N/A
5.3.3
Transformers
Pass
5.3.4
Functional insulation.............................................. : Functional insulation complies
with the requirements (a), (b),
or (c).
Pass
5.3.5
Electromechanical components
N/A
5.3.6
Simulation of faults
Pass
5.3.7
Unattended equipment
N/A
5.3.8
Compliance criteria for abnormal operating and
fault conditions
Pass
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
Test voltage (V) ..................................................... :
-
Current in the test circuit (mA)............................... :
-
6.1.2.2
Exclusions ............................................................. :
N/A
6.2
Protection of equipment users from overvoltages on telecommunication
networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 25 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
6.3
Protection of the telecommunication wiring system from overheating
Verdict
N/A
Max. output current (A).......................................... :
-
Current limiting method ......................................... :
-
7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
Protection of cable distribution system service persons, and users of other
equipment connected to the system, from hazardous voltages in the equipment
N/A
7.2
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.3
Insulation between primary circuits and cable
distribution systems
N/A
7.3.1
General
N/A
7.3.2
Voltage surge test
N/A
7.3.3
Impulse test
N/A
A
Annex A, TESTS FOR RESISTANCE TO HEAT AND FIRE
N/A
A.1
Flammability test for fire enclosures of movable equipment having a total mass
exceeding 18 kg, and of stationary equipment (see 4.7.3.2)
N/A
A.1.1
Samples................................................................. :
-
Wall thickness (mm) .............................................. :
-
A.1.2
Conditioning of samples; temperature (°C) ........... :
N/A
A.1.3
Mounting of samples ............................................. :
N/A
A.1.4
Test flame
N/A
A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s) ..................................... :
-
Sample 2 burning time (s) ..................................... :
-
Sample 3 burning time (s) ..................................... :
-
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 26 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A.2
Flammability test for fire enclosures of movable equipment having a total
mass not exceeding 18 kg, and for material and components located inside
fire enclosures (see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material.................................................. :
-
Wall thickness (mm) .............................................. :
-
N/A
A.2.2
Conditioning of samples
N/A
A.2.3
Mounting of samples
N/A
A.2.4
Test flame
N/A
A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s) ..................................... :
-
Sample 2 burning time (s) ..................................... :
-
Sample 3 burning time (s) ..................................... :
-
Alternative test acc. to IEC 60695-2-2, cl. 4, 8
N/A
Sample 1 burning time (s) ..................................... :
-
Sample 2 burning time (s) ..................................... :
-
Sample 3 burning time (s) ..................................... :
-
A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 27 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
B
Annex B, MOTOR TESTS UNDER ABNORMAL CONDITIONS(see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Position .................................................................. :
-
Manufacturer ......................................................... :
-
Type....................................................................... :
-
Rated values.......................................................... :
-
B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days)............................................... :
-
Electric strength test: test voltage (V).................... :
-
B.6
Running overload test for d.c. motors in secondary
circuits
N/A
B.7
Locked-rotor overload test for d.c. motors in secondary circuits
N/A
B.7.1
Test procedure
N/A
B.7.2
Alternative test procedure; test time (h) ................ :
N/A
B.7.3
Electric strength test
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V) ............................................ :
TRF No.: IEC60950__1A
UL International Demko A/S
-
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 28 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
C
Annex C, TRANSFORMERS (see 1.5.4 and 5.3.3)
Verdict
Pass
Position .................................................................. : T1
-
Manufacturer ......................................................... : PULS
-
Type....................................................................... : TE-339.590.00 and TE339.590.05;
-
Rated values.......................................................... : Refer to Enclosures
-
Method of protection.............................................. : Inherently protected
-
C.1
Overload test
C.2
Insulation
Pass
(see appended table 5.2)
Pass
Protection from displacement of windings............. : Windings suitable secured by
tape and/or margin spacer.
Pass
D
Annex D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
Pass
D.1
Measuring instrument
Pass
D.2
Alternative measuring instrument
N/A
E
Annex E, TEMPERATURE RISE OF A WINDING
Pass
F
Annex F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10)
Pass
TRF No.: IEC60950__1A
D.1 circuit used.
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 29 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
G
Annex G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply
N/A
G.2.2
DC mains supply
N/A
G.3
Determination of telecommunication network
transient voltage (V) : ............................................ :
N/A
G.4
Determination of required withstand voltage (V) ... :
N/A
G.5
Measurement of transient levels (V)...................... :
N/A
G.6
Determination of minimum clearances .................. :
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
Annex J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
Pass
Metal used ............................................................. : Aluminium/Zinc alloy.
-
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V).......... :
N/A
K.3
Thermostat endurance test; operating voltage (V) :
N/A
K.4
Temperature limiter endurance; operating voltage
(V) .......................................................................... :
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
TRF No.: IEC60950__1A
UL International Demko A/S
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 30 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
L
Annex L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.1)
N/A
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
N/A
M
Annex M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz)...................................................... :
-
M.3.1.2
Voltage (V)............................................................. :
-
M.3.1.3
Cadence; time (s), voltage (V)............................... :
-
M.3.1.4
Single fault current (mA)........................................ :
-
M.3.2
Tripping device and monitoring voltage................. :
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V) ........................................... :
N/A
N
Annex N, IMPULSE TEST GENERATORS (see 2.10.3.4, 6.2.2.1, 7.3.2 and
clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
TRF No.: IEC60950__1A
Result - Remark
UL International Demko A/S
Verdict
TRF originator: SGS FIMKO
Issue Date:
2005-08-06
Page 31 of 58
Report Reference #
E137006-A6-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
P
Annex P, NORMATIVE REFERENCES
Pass
Q
Annex Q, BIBLIOGRAPHY
Pass
R
Annex R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
Annex S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
Annex T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER (see
1.1.2)
N/A
............................................................................... :
U
-
Annex U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
............................................................................... :
TRF No.: IEC60950__1A
UL International Demko A/S
Verdict
N/A
-
TRF originator: SGS FIMKO
This is an extract of the CB-Scheme report with the most important information.
If a complete copy of the report is required, please contact your PULS sales representative.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement