09/2009
Einbauanweisung
Installation instructions
Notice de montage
Istruzioni di montaggio
Instrucciones de montaje
Montagehandleiding
Monteringsvejledning
Monteringsanvisning
Monteringshåndbok
Asennusohje
Instrukcja monta ż u
Návod k instalaci
Beépítési utasítás
Инструкция по монтажу
Telestart T91 / T100 HTM
Improper installation or repair of Webasto heating and cooling systems can cause fire or the leakage of deadly carbon monoxide leading to serious injury or death.
To install and repair Webasto heating and cooling systems you need to have completed a Webasto training course and have the appropriate technical documentation, special tools and special equipment.
NEVER try to install or repair Webasto heating or cooling systems if you have not completed a Webasto training course, you do not have the necessary technical skills and you do not have the technical documentation, tools and equipment available to ensure that you can complete the installation and repair work properly.
ALWAYS carefully follow Webasto installation and repair instructions and heed all WARNINGS.
Webasto rejects any liability for problems and damage caused by the system being installed by untrained personnel.
Inhalt
Einbauanweisung .......................................................1
Allgemein .................................................................1
Zertifizierung ............................................................1
Schalteingang für analoge Anbindung der
Bedienelemente .....................................................2
Vorwahluhr .........................................................2
Taster ..................................................................2
Umstellung Schalteingang von „Vorwahluhr“ auf „Taster“ ...................................................2
Umstellung Schalteingang von „Taster“ auf „Vorwahluhr“ ..........................................2
Lieferumfänge .............................................................3
Lieferumfang T91 ................................................3
Lieferumfang T100 HTM ......................................3
D-Netz Telefonkit (Option) ...................................3
Einbau ..........................................................................4
Einbau Telestart-Empfänger .................................4
Einbau Antenne ...................................................4
Einbau D-Netz Telefonkit (Option) ........................5
Einbau ESVT-Adapter
(am Beispiel Thermo Top C) ............................5
Telestart T91 / T100 HTM Nachrüstung .....................6
In Verbindung mit bestehender oder neu zu verbauender Vorwahluhr .................................6
In Verbindung mit Taster ..........................................7
Telestart T80 mit Vorwahluhr vorhanden ..................7
Option Lüften bei analoger Anbindung .....................8
Sommer-/Winterschalter vorhanden
(Option Lüften aktivieren) ...............................8
Sommer-/Winterschalter vorhanden
(Option Lüften deaktivieren) ...........................8
Sommer-/Winterschalter neu installieren
(Option Lüften aktivieren) ...............................8
Einbau Temperatursensor
(nur bei T100 HTM) .............................................9
Grundeinstellungen der Komfortstufe .......................9
Technische Daten ......................................................10
Anlagen ....................................................................11
Content
Installation Instructions ........................................... 15
General information ............................................... 15
Certification ........................................................... 15
Switching input for analogue connection of heater controls ................................................................. 16
Digital timer ...................................................... 16
Pushbutton switch ............................................. 16
Changeover of switching input from
"digital timer" to "pushbutton switch" ........ 16
Changeover of switching input from
"pushbutton switch" to "digital timer" ........ 16
Scope of delivery ...................................................... 17
Scope of delivery for T91 ................................... 17
Scope of delivery for T100 HTM ........................ 17
D network telephone kit (option) ....................... 17
Installation ................................................................ 18
Installation of Telestart receiver ......................... 18
Installation of aerial ........................................... 18
Installation of D network telephone kit (option) . 19
Installation of ESVT adapter
(using example of Thermo Top C) ................. 19
Telestart T91/T100 HTM retrofit .............................. 20
In conjunction with existing or new digital timer to be installed ................................................... 20
In conjunction with pushbutton .............................. 21
Telestart T80 with digital timer installed .................. 21
Ventilation option with analogue connection .......... 22
Summer/winter switch installed
(activate ventilation option) .......................... 22
Summer/winter switch installed
(deactivate ventilation option) ...................... 22
Install new summer/winter switch
(activate ventilation option) .......................... 22
Temperature sensor installation
(only with T100 HTM) ........................................ 23
Default settings of comfort level ............................. 23
Technical data .......................................................... 24
Appendices ............................................................... 25
Telestart T91 / T100 HTM
Index
Notice de montage ................................................... 29
Informations générales ........................................... 29
Certification ........................................................... 29
Entrée de couplage pour la connexion analogique des éléments de commande ............................... 30
Horloge de programmation ............................... 30
Bouton-poussoir ................................................ 30
Passage de l'entrée de couplage de « horloge de programmation » à « bouton-poussoir » ...... 30
Passage de l'entrée de couplage de « bouton-poussoir » à «horloge de programmation ............ 30
Compositions de la fourniture ................................ 31
Composition de la fourniture T91 ...................... 31
Composition de la fourniture T100 HTM ........... 31
Kit téléphone réseau D (en option) .................... 31
Montage .................................................................... 32
Montage du récepteur Telestart ........................ 32
Montage de l'antenne ....................................... 32
Montage du kit téléphone réseau D (en option) 33
Montage de l'adaptateur ESVT
(à l'exemple du Thermo Top C) .................... 33
Telestart T91/T100 HTM de deuxième monte ........ 34
En combinaison avec une horloge de programmation déjà existante ou devant encore être montée .... 34
En combinaison avec le bouton-poussoir ................ 35
Telestart T80 avec horloge de programmation déjà existant ...................................................... 35
Option ventilation en cas de connexion analogique 36
Interrupteur été/hiver déjà existant
(activation de l'option ventilation) ................ 36
Interrupteur été/hiver déjà existant
(désactivation de l'option ventilation) ........... 36
Interrupteur été/hiver devant encore être installé
(activation de l'option ventilation) ................ 36
Montage du capteur de température
(uniquement sur le T100 HTM) .......................... 37
Réglages de base du niveau de confort .................. 37
Caractéristiques techniques .................................... 38
Annexes ................................................................... 39
I
Installation Instructions
General information
The Webasto heaters of the Thermo Top series can be retrofitted with the Webasto
Telestart T91 and T100 HTM.
The D network telephone kit (option) enables the Telestart receiver to be connected to any existing D network aerial.
Certification
The CE mark is visible when the battery compartment cover is open.
The e1 mark is located on the Telestart receiver.
Telestart T91 / T100 HTM
15
Telestart T91 / T100 HTM
Switching input for analogue connection of heater controls
In addition to the Telestart, a digital timer or a pushbutton switch can be installed.
Digital timer
Caution:
The digital timer and the pushbutton switch transmit differing signals to the Telestart receiver!
The signal input must be adapted to the appropriate heater control!
By default, the signal input of the Telestart receiver is tuned to the digital timer!
The included ESVT adapter must be adapted to the existing installation situation (heater controls and heaters) accordingly by "pinning it in".
See Kapitel "Appendices".
When the heater is activated (by pressing the instant heat button or by the start of a preset heater operating time) the Telestart receives a continuous plus signal from the digital timer during the entire operating time.
Upon deactivation of the heater (by pressing the instant heat button or when the end of the operating time preset on the digital timer is reached), the positive signal is cut off and the heater is switched off.
Pushbutton switch
Upon switching on or off using the pushbutton switch, the Telestart receiver receives a short plus signal.
For the Telestart to be able to recognise this signal, the switching input needs to be set to
"pushbutton switch".
The heater does not switch on if the switching input is not changed over to "pushbutton switch". Instead, it enters the postoperation stage and then switches off.
Changeover of switching input from "digital timer" to "pushbutton switch"
- Remove fuse 1A (black) from the heater's fuse holder (voltage interruption).
- Wait at least 5 seconds
- Install fuse in heater's fuse holder and briefly actuate the pushbutton switch
1x within 5 seconds
- Changeover is terminated
Changeover of switching input from "pushbutton switch" to
"digital timer"
- Remove fuse 1A (black) from the heater's fuse holder (voltage interruption).
- Wait at least 5 seconds
- Install fuse in heater's fuse holder and briefly actuate the instant heat button on the digital timer within 5 seconds
(display back lighting is illuminated)
- After 10 seconds briefly actuate the instant heat button (display back lighting is extinguished)
- Changeover is terminated
16
Telestart T91 / T100 HTM
Scope of delivery
Scope of delivery for T91
1 2 3
4
Scope of delivery for T100 HTM
1 2 3
4
D network telephone kit (option)
1 2
6
5
7
6
5
1 T91 transmitter
2 3 V battery
3 Mounting bracket
4 T91/T100 HTM receiver
5 ESVT adapter
6 Aerial
1 T100 HTM transmitter
2 6 V battery
3 Mounting bracket
4 T91/T100 HTM receiver
5 ESVT adapter
6 Aerial
7 Temperature sensor
1 Duplexer GSM/Telestart
2 HF-adapter cable (190 mm)
17
Telestart T91 / T100 HTM
Installation
The installation of the Telestart T91/T100
HTM may only be performed by an authorised Webasto dealer.
Installation of Telestart receiver
Caution:
The Telestart receiver must be installed in the interior of the vehicle!
The preferred installation position is with the plug-in connectors pointing downward, with a maximum permissible deviation from the perpendicular of <45° in either direction.
Mounting bracket
Receiver
- Secure the mounting bracket using sheet-metal screws
- Fit receiver into the mounting bracket
Installation of aerial
Note:
Preferably, the aerial should be installed in the interior of the vehicle, at the top in the centre of the windshield or the rear window.
If installed in other locations, the range is likely to be diminished.
For an optimal reception, a distance of
20 +/- 5 mm from the windshield edge is to be maintained (see Fig.).
Depending on the installation location of the aerial, the cable is routed either under the vehicle roof trim and then to the right or left to the strut or directly downward under the instrument panel. max. 300
Note:
If there is insufficient space available, the aerial may be installed up to 150 mm off-centre.
- Clean windshield using grease-dissolving cleaner (e.g. methylated spirits)
- Peel off protective film from aerial and fix aerial into place
Note:
Do not shorten aerial cable nor bend it sharply.
Smallest winding diameter is 50 mm.
Aerial
Receiver
- Route aerial cable to the receiver and connect it to the receiver - Define the installation location of the receiver in the interior of the vehicle
(preferably near the digital timer in the case of retrofits)
18
Additional installation location
Installation of D network telephone kit (option)
Connect duplexer GSM/Telestart into the existing D network aerial feeder line.
Receiver
Installation of ESVT adapter
(using example of Thermo Top C)
Receiver
Telestart T91 / T100 HTM
- Route 4-pin connector of digital timer of heater wiring harness into vehicle interior
- Connect ESVT adapter to 4-pin connector of digital timer
- Connect ESVT adapter to Telestart receiver
- Connect ESVT adapter to temperature sensor (only with Telestart T100 HTM)
GSM duplexer
Adapter line
- Connect existing D network aerial feeder line to the input of the GSM duplexer
- Connect adapter line (length:190 mm) to the Telestart output of the GSM duplexer and to the Telestart receiver
- Connect the telephone line to the telephone output of the GSM duplexer
ESVT adapter
Connector of
Digital timer
Temperature sensor
(only with
T100 HTM)
Pinning in cables on ESVT adapter: see
- Appendice 1 for analogue control
- Appendice 3 for W-bus control
19
Telestart T91 / T100 HTM
Telestart T91/T100 HTM retrofit
In conjunction with existing or new digital timer to be installed
Receiver
Pinning in cables on ESVT adapter: see
- Appendice 1 for analogue control
- Appendice 3 for W-bus control
25A
15A
1A
Connector of
Digital timer
1
2
3
Digital timer
ESVT adapter
- Connect ESVT adapter to 4-pin connector of digital timer
- Connect ESVT adapter to Telestart receiver
- Connect ESVT adapter to temperature sensor (only with T100 HTM)
- Connect ESVT adapter to digital timer
Note:
Do not pull at the cables!
- Disconnect 4-pole connector from digital timer
Connector of
Digital timer
Temperature sensor
(only with
T100 HTM)
1
2
3
Digital timer
20
In conjunction with pushbutton
Receiver
ESVT adapter
Temperature sensor
(only with
T100 HTM)
Digital timer connector
Pushbutton
Switch
- Connect ESVT adapter to 4-pin connector of digital timer
- Connect ESVT adapter to Telestart receiver
- Connect ESVT adapter to temperature sensor (only with Telestart T100 HTM)
- Drill hole (16 mm dia.) in location agreed upon with customer.
- Install pushbutton switch
Note:
When inserting the contacts into the receptacle housing of the pushbutton switch, ensure that the colour coding matches that of the ESVT adapter.
- Insert contacts into receptacle housing of the pushbutton switch
- Connect the ESVT adapter to the connector on the pushbutton switch.
Caution:
The default setting of the signal input must be changed from digital timer to pushbutton switch. See page 16.
Telestart T91 / T100 HTM
Telestart T80 with digital timer installed
- Remove Telestart T80 receiver
- Install Telestart T91/T100 HTM receiver as described in installation instructions
Note:
The bracket of the T80 can be used to install the T91/T100 HTM receiver.
- Remove Y-adapter and replace with ESVT adapter
Pinning in cables on ESVT adapter: see
- Appendice 1 for analogue control
- Appendice 3 for W-bus control
Pinning in cables on ESVT adapter: see
- Appendice 2 for analogue control
- Appendice 4 for W-bus control
21
Telestart T91 / T100 HTM
Ventilation option with analogue connection
1
1
ESVT adapter
Summer/winter switch installed
(activate ventilation option)
- Remove the existing Y-cable and/or the existing ESV adapter
- Connect the ESVT adapter as described in these installation instructions
- The summer/winter switch (2) remains mounted
- The heating or ventilation function is determined by the summer/winter switch, independent of the setting on the transmitter or digital timer vi br
2
Summer/winter switch installed
(deactivate ventilation option)
- Remove the existing Y-cable and/or the existing ESV adapter
- Connect the ESVT adapter as described in these installation instructions
- Disconnect the brown (br) and violet
(vi) connection cable from the summer/ winter switch (2).
- Insulate and tie back the cable ends
- The summer/winter switch is now inoperative and can be removed if desired. The ventilation function has now been deactivated
Install new summer/winter switch (activate ventilation option)
- Expose the brown (br) and violet (vi) connection cable from the heater wiring harness (1).
- Mount and connect the summer/winter switch (2) at the desired installation location
- The heating or ventilation function is determined by the summer/winter switch, independent of the setting on the transmitter or digital timer
22
Temperature sensor installation (only with T100 HTM)
The supplied temperature sensor should be arranged in the vehicle so it takes a representative measurement of the temperature inside the vehicle.
The temperature sensor should be fitted:
- Where it is not exposed to direct sunlight
- Where it is not close to the vehicle heating nozzles
T100 HTM temperature sensor
- Define the installation location of the temperature sensor inside the vehicle
(check how much cable is available)
- Attach the temperature sensor with a
3.5 mm self-tapping screw (max. torque 1 Nm)
Telestart T91 / T100 HTM
Default settings of comfort level
Teach-in the Telestart T100 HTM as described in the operating and servicing manual.
We recommend the default settings in accordance with Table 1 depending on the vehicle type and the heater used.
Note:
These settings can be optimised to suit the customer's individual comfort requirements.
Table 1 Default settings of comfort level
Max. heat flow of heater 4 kW 5 kW
Compact car
Mid-size car, mini van, sedan
Full-size car, van, SUV
C3
C4
-
C2
C3
C4
5 kW
(with circulation pump cycling)
C1
C2
C3
23
Telestart T91 / T100 HTM
Technical data
Transmitter
Size L/W/H [mm]
Weight [g]
Transmitter power [mW]
Transmitter frequency [MHz]
Battery [V]
Display
Operating/storage temperature
(without batteries) [ºC]
Receiver
Current consumption [mA]
Size L/W/H [mm]
Receiver sensitivity [dBm]
Aerial connection
Connectors
Operating/storage temperature [ºC]
System
Standard functions
No. of transmitters
Range [m]
Telestart T91 approx. 54 x 32 x 16
16
25
868,3
3 (recommended: DL 1/3N Duracell battery)
Multicolour LED
0 to +50/-40 to +85
Telestart T100 HTM approx. 70 x 37 x 18
45
25
868,3
6 (recommended: PX28L Duracell battery)
LCD display
0 to +50/-20 to +70
< 1 (bias current) approx. 85 x 65 x 16
-110
FAKRA aerial connector, Coding I
MQS 6-pin socket housing, Tyco 1-1241370-3
-40 to +85 (also applies to temperature sensor)
ON, OFF, heating, ventilation (only with W-bus control), HTM (only with Telestart T100 HTM) up to 4 transmitters can be programmed typical: 600 optimal: 1,000 in the open and from an elevated location, hold transmitter vertically
24
Telestart T91 / T100 HTM
Appendices
Telestart
Digital timer
View of cable side
View of cable side
T-sensor optional for HTM not equipped: ge, sw
Heater
View of cable side br ge: brown yellow gr: rt: grey red sw: black not equipped: ge
Appendice 1 Heater with analogue control; Telestart without additional heater control or with
1533 or 1530 digital timer
25
Telestart T91 / T100 HTM
Telestart
1 6
1 rt
2 ge
3 sw
4 gr
5 ---
6 b r
Pushbutton Switch
4
1
3
2
View of cable side
1 sw
2 gr
3 rt
4 b r not equipped: ge
Heater br ge: gr: brown yellow grey rt: red sw: black
View of cable side
-sw rt b r not equipped: ge
Appendice 2 Heater with analogue control; Telestart additional pushbutton
View of cable side
2 1
3 4
T-sensor optional for HTM
3
4
1
2 ge
--rt b r
26
Telestart T91 / T100 HTM
Telestart
1 6
1 rt
2 ge
3 sw
4 gr
5 ---
6 b r
Digital timer
4
1
3
2
View of cable side
1 ge
2 --
3 rt
4 b r not equipped: gr, sw
View of cable side
2 1
3 4
T-sensor optional for HTM
3
4
1
2 rt b r ge
---
Heater br ge: gr: brown yellow grey rt: red sw: black
View of cable side ge
-rt b r not equipped: sw
Appendice 3 Heater with W-bus control; Telestart without additional heater control or with 1533 digital timer
27
Telestart T91 / T100 HTM
Telestart
1 6
1 rt
2 ge
3 sw
4 gr
5 ---
6 b r
Pushbutton Switch
4
1
3
2
View of cable side
1 sw
2 gr
3 rt
4 b r not equipped: ge
Heater br ge: gr: brown yellow grey rt: red sw: black
View of cable side ge
-rt b r not equipped: sw
Appendice 4 Heater with W-bus control; Telestart additional pushbutton
View of cable side
2 1
3 4
T-sensor optional for HTM
1
2
3
4 ge
--rt b r
28
Im Fall einer mehrsprachigen Version ist Deutsch verbindlich.
In multilingual versions the German language is binding.
Dans le cas d'une version rédigée en plusieurs langues, l'allemand est alors la langue qui fait foi.
Nel caso di una versione plurilingue il tedesco è vincolante.
Este manual esta traducido en varios idiomas, le informamos que sólo la versión en alemán será vinculante.
Bij een meertalige versie is de Duitse versie bindend.
I tilfælde af en flersproget udgave er den tyske version gældende.
Om det förekommer en flerspråkig version är den tyska bindande.
Hvis det finnes en flerspråklig versjon, er det den tyske som har forrang.
Useampikielisten versioiden yhteydessä saksankielinen on sitova.
W przypadku wersji kilkuj ę zy č znej wi ążą cy jest tekst w j ę zyku niemieckim.
V p ř ípad ě vícejazycné verze je závazná n ě m č ina.
Többnyelv ű változat esetén a német nyelv ű t is kötelez ő en tartalmaznia kell.
Для изданий на нескольких языках обязательным является немецкий вариант .
Webasto AG
Postfach 80
D - 82131 Stockdorf
Germany
National:
Hotline: 01805 93 22 78
( € 0,14 aus dem deutschen
Festnetz)
Hotmail: [email protected]
www.webasto.de
International: www.webasto.com
http://dealers.webasto.com
