Product datasheet

Product datasheet
specification
HP
Oscilloscopes
I n f i n i i u m Probes and Accessories
Tools to get your job done faster
• Probes
• Accessories
• Input devices
1
The HP 1160 Family of
Miniature Passive Probes
Rugged, general purpose
probes for HP Infiniium
Oscilloscopes
Before we developed the
HP 1160 family of miniature
probes, we conducted intensive
market research. We used
focus groups, surveys, and
interviews to ask engineers
about their frustrations with
probing. We heard that probes
often slip off the test point
being probed and short to
adjacent leads. We heard that a
variety of ground accessories
are needed to connect to
HP 1160 probes and accessories
different points. And we were
told that reliability is always a
concern. We used this feedback
Reliability
to guide our development team as we built
The HP 1160 family probes are built and tested
the HP 1160 family of miniature probes.
for high reliability. The cable has a Kevlar®
strengthener for added pull strength. The
No-slip browser
general purpose retractable hook tip has a
We developed a new
durable music wire hook. And probe tips are
browser with a crown
replaceable.
point that digs in to
solder, and won't slip.
Miniature size
Install the browser over
To miniaturize the probe, unscrew the handle
the probe tip, and probe
and pull it back on the cable. The miniature
about the board while
probe has a narrow, sharp tip that is excellent
debugging your circuit.
for probing SMD.
The pogo pin allows hand
movement without losing
AutoProbe Interface Compatible
Browser
crown point
contact.
The HP 1160 family probes are compatible with
the AutoProbe Interface, which completely
A variety of grounding accessories
configures the HP Infiniium Oscilloscope for
The HP 1160 family probes come with an
the probe. The snap-on BNC connector makes
alligator lead for general purpose probing,
it easy to attach the probe to the scope.
4 spring grounds for high frequency
measurements, a socketed ground lead and
SMD clips for probing 50 mil SMD. Also
included is a dual lead adapter so that both the
probe tip and ground can be connected to SMD
devices. For connection to 0.5mm- 0.8mm
devices order the optional HP 10467-687010
0.5mm IC clips.
2
HP 1160 Family
Selection Guide
Model
Number
Type of Probe
System
Division
Bandwidth
Ratio
(scope +probe)
Input R
Input C
Scope
Input R
Compensation Length
Range
HP 1160A
High Impedance,
Passive
500 MHz
10:1
10 MΩ
9 pF
1 MΩ
6 - 9 pF
1.5 m
HP 1161A
High ImpeSce,
Passive
500 MHz
10:1
10 MΩ
10 pF
1 MΩ
12 - 14 pF
1.5 m
HP 1162A
High Impedance,
Passive
25 MHz
1:1
1 MΩ
50 pF + scope 1 MΩ
capacitance
n/a
1.5 m
HP 1163A
500 Ω Resistive Divider 1.5 GHz
10:1
with HP 54845A
500 Ω
1.5 pF
50 Ω
n/a
1.5 m
HP 1164A
Passive
High Impedance,
10 MΩ
10 pF
1Ω
6 - 9 pF
2.0 m
500 MHz
10:1
Compatibility
Scope
HP 54810A
HP 54815A
HP 54820A
HP 54825A
HP 54845A
Ordering Information
Probe
HP 1160A, 1162A, 1163A, 1164A
HP 1160A, 1162A, 1163A, 1164A
HP 1160A, 1162A, 1163A, 1164A
HP 1160A, 1162A, 1163A, 1164A
HP 1161A, 1162A, 1163A
Characteristics
Approximate Propagation Delay
Maximum Input Voltage
Safety
Pull Strength (BNC to barrel)
Net Weight
6.7 ns
300 V (dc + peak ac), CAT II
Meets IEC1010-2-31
≥ 12 lb static pull
2.6 oz
Environmental Characteristics
Temperature (Operating)
Humidity(Operating)
Altitude(Operating)
Shock
HP 1160A 10:1, 10 MΩ, 1.5 m,
miniature passive probe
HP 1161A 10:1, 10 MΩ, 1.5 m,
miniature passive probe
HP 1162A 1:1, 1.5 m,
miniature passive probe
HP 1163A 10:1, 500 Ω, low C, 1.5 m,
miniature passive probe
HP 1164A 10:1, 10 MΩ, 2 m, miniature passive probe
Each HP 1160 family probe includes: 1 probe assembly,
1 general-purpose retractable hook tip, 1 browser,
2 barrel insulators, 4 spring grounds, 1 alligator ground lead,
1 socketed ground lead, 1 dual lead adapter, 2 SMD grabbers,
1 spare browser pogo pin,1 spare probe tip, and 1 screw driver,
1 users’ reference and a three-year warranty.
0° C to +55° C
Up to 95% relative humidity
at 40° C
Up to 4,600 meters (15,000 ft.)
50 g (400 g tip only)
Available Accessories
HP 10467-68701 0.5 mm IC clips for connection to
SMD with lead spacings of .5mm (.020") to .8mm (.032")
Replacement Parts
HP 5063-2135 General purpose retractable hook tip, Qty 2
HP 5063-2140 Alligator ground lead, Qty 2
HP 5063-2120 Socketed ground lead, Qty 1
HP 5063-2115 Browser, Qty 1
HP 5063-2147 Dual lead adapter, Qty 1
HP 5063-2149 SMD clips, Qty 5
HP 01160-68701 Accessory kit (includes 4 spring grounds,
4 browser pogo pins, 4 barrel insulators, 1 screw driver)
HP 5063-2136 HP 1160A probe tip, Qty 5
HP 5063-2137 HP 1161A probe tip, Qty 5
HP 5063-2138 HP 1162A probe tip, Qty 5
HP 5063-2139 HP 1163A probe tip, Qty 5
3
The HP 1170 Family of Low Mass Passive Probes
and Fine-Pitch Probing Kits
Small, easy-to-connect
probes for HP Infiniium
Oscilloscopes
As ICs and components
continue to shrink in size,
probing has become
increasingly difficult.
Developed for easy
connection to fine-pitch ICs,
surface mount components
and dense circuit boards, the
HP 1170 family of low mass
passive probes makes the job
of probing and connecting
less frustrating. With an
exceptionally small, light
probe tip (<1 gram), these
passive probes provide the
same high-performance and
reliability you've come to expect from HP's
high-performance passive probes. Add an ultrathin, flexible cable, and the HP 1170 probes are
not only easy to connect, they stay put on the
test point.
Easy to connect, Easy to hold
You'd think a probe this small would be hard to
hold, but the HP 1170-family of probes plug in
to a browser accessory that makes them as
easy to hold as a conventional probe. This
patented browser concept utilizes a crown
point pogo pin that digs in to solder and
absorbs small hand movement, so doesn't slip.
When used in conjunction with the HP Wedge,
the HP 1170 probes provide a reliable handsfree solution for probing 0.5-mm and 0.65-mm
IC packages and the probe tip also connect
directly to board headers.
Low capacitive loading
Typical passive probes feature a 10:1 division
ratio and a tip capacitance of approximately
10 pF or more. In sharp contrast, the
HP 1172A and 1173A's 20:1 division ratio
provides a low tip capacitance of less than 5 pF
making these passive probes much better
suited for the fast rise times of today's ICs.
Complements your
standard passive probe
The HP 1170 probes' low mass and
size, combined with the flexibility provided
by the no-slip browser and the HP Wedge
(see page 12)make it the ideal supplement to
your standard passive probe. And that can
really ease fine pitch frustrations. The
HP 1170 family of probes include IC clips,
miniature socketed leads and a complete
selection of probing and grounding accessories.
Fine-Pitch Probing Kits
A complete solution, a bargain price!
The HP fine-pitch probing kits take the
1170-family of probes and add the most useful
fine-pitch probing accessories to give you a
versatile and complete probing solution.
Each kit include 2 HP 1170-family probes and
its’ accessories, 2 of the 0.5 mm HP Wedge
probe adapters, 4 of our 0.5 mm IC clips and
10 standard IC clips. All for a price
substantially less than the individual parts.
4
HP 1170 Family
Selection Guide
Model
Number
Type of Probe
System
Division
Bandwidth
Ratio
(scope +probe)
Input R
Input C
Scope
Input R
Compensation Length
Range
HP 1170A
High Impedance,
Passive
500 MHz
10:1
10 MΩ
9pF
1M
6 - 9 pF
1.5 m
HP 1171A
High Impedance,
Passive
500 MHz
10:1
10 MΩ
10 pF
1M
12 - 14 pF
1.4 m
HP 1172A
High Impedance,
Passive
500 MHz
20:1
10 MΩ
< 5 pF
1M
6 - 9 pF
1.3 m
HP 1173A
High Impedance,
Passive
500 MHz
20:1
10 MΩ
< 5 pF
1M
12 - 14 pF
1.2 m
Compatibility
Scope
HP 54810A
HP 54815A
HP 54820A
HP 54825A
HP 54845A
Ordering Information
Probe
HP 1170A, HP 1172A
HP 1170A, HP 1172A
HP 1170A, HP 1172A
HP 1170A, HP 1172A
HP 1171A, HP 1173A
Characteristics
Approximate Propagation Delay
Maximum Input Voltage
Safety
Pull Strength (BNC to probe tipl)
Net Weight
Probe Tip Weight
7 ns, 6.5, 6.0, 5.5
40V (dc + peak ac), CAT I
Meets IEC1010-2-31
≤ 12 lb static pull
2.6 oz
< 1 gram
Environmental Characteristics
Temperature (Operating)
Humidity (Operating)
Altitude (Operating)
Shock
0° C to +55° C
Up to 95% relative humidity
at 40° C
Up to 4,600 meters
(15,000 ft.)
50 g (400 g tip only)
Low Mass Passive Probes
HP 1170A 10:1, 10 MΩ , 1.5 m,
low mass passive probe
HP 1171A 10:1, 10 MΩ , 1.4 m,
low mass passive probe
HP 1172A 20:1, 10 MΩ , 1.3 m,
low mass passive probe
HP 1173A 20:1, 10 MΩ , 1.2 m,
low mass passive probe
Each HP 1170A family probe includes: 1 probe assembly,
1 browser, 2 probe pins, 2 pogo pins, 2 IC clips, 1 screwdriver,
1 alligator ground, 1 socketed ground, 1 walking stick ground,
1 ground extender and a user's guide.
Fine Pitch Probing Kits
HP E2652A Fine-Pitch Probing Kit for
HP 54810/15/20/25A
HP E2653A Fine-Pitch Probing Kit for HP 54845A
Each kit includes. 2 HP 1172A (E2652A) or
HP 1173A (E2653A) low mass probes and their accessories,
2 x 0.5 mm HP Wedge Probe Adapters,
4 x 0.5 mm IC clips, 10 x std IC clips.
Fine Pitch IC Probing Accessories
HP E2613B HP Wedge probe adapter, .5mm,
3-signal, Qty 2
HP E2614A HP Wedge probe adapter, .5mm,
8-signal, Qty 1
HP E2615B HP Wedge probe adapter, .65mm,
3-signal, Qty 2
HP E2616A HP Wedge probe adapter, .65mm,
8-signal, Qty 1
HP10467-68701 0.5mm IC clips for
surface SMT parts with leg spacing of
.5mm (.020") to .8mm (0.32 "), Qty 4
Other Accessories
HP E9638A Probe tip to BNC (m) adapter
Replacement Parts
HP E2642A Accessory replacement kit
5
HP 1152A 2.5 GHz Active Probe
for HP Infiniium Oscilloscopes
Nonintrusive, reliable
probing provides faithful
reproduction of signals
The HP 1152A’s bandwidth, superior
accuracy, and reliability make it an
ideal companion for the HP 54845A
1.5 GHz bandwidth oscilloscope.
Nonintrusive
The low input capacitance of the
active probe eliminates distortion
caused by excessive loading.
As frequency increases, probe tip
capacitance decreases the
impedance of the probe by
HP 1152A probe and accessories
Xc = 1/(2π fC), resulting in
measurement error, depending on
Compare Active and Passive Probe Performance
the source impedance of the output device.
The HP 1152A’s low tip capacitance becomes a
See how the HP 1152A active probe compares
distinct advantage as frequency increases.
to a 50 Ω coaxial cable and an HP 1161A
passive probe when probing a 1 ns edge.
The higher bandwidth and nonintrusiveness of
the active probe result in faithful reproduction
of the signal.
See how well the HP 1152A reproduces this
600 ps edge - even with no ground lead attached.
50 Ω cable
HP 1152A probe
HP 1161A probe
Faithful Reproduction of high frequency edges…
even with no ground lead
50 Ω cable
HP 1152A probe
HP 1152A probe with no ground lead
6
Faithful reproduction
Characteristics
• 2.5-GHz bandwidth
Bandwidth (-3dB)*
System Bandwidth with HP 54845A
with HP 54810A/15A/20A/25A
Risetime (10% to 90%)
• 140-ps rise time
• 1% long-term flatness
• ±0.5% dc gain accuracy
The HP 1152A active probe offers digital
designers 2.5 GHz of bandwidth for extending
measurement response, along with 140-ps rise
time for accurate measurement of fast signals.
Adding 1% long-term flatness, and ±0.5% dc
gain accuracy, results in a clearer
representation of the input signal than ever
before possible.
Superior reliability
• 200-Vac max input tolerance
• ±12-kV ESD tolerance
• Pliable, replaceable probe tips
• ±5-V dc + peak ac
The HP 1152A’s microcircuits are protected by
their ability to withstand damage from highinput voltage, ESD pulses, and shock to the
probe tips. The HP 1152A’s probe tips are rigid
enough for probing, yet pliable enough to bend
if dropped, protecting the microcircuits from
damage. In addition, the probe tips are easy
and inexpensive to replace. You’ll appreciate
the reliability and ruggedness of the HP 1152A.
AutoProbe Interface Compatible
The HP 1152A is compatible with the
AutoProbe Interface which completely
configures the HP Infiniium Oscilloscope for
the probe. The interface recognizes the probe,
and automatically sets up the proper power,
50-Ω impedance and offset range.
Attenuation Factor*
dc Input Resistance*
dc Gain Accuracy*
(with 50 ± 0.1 Ω load)
Input Capacitance
Flatness
(with input edge ≥170 ps)
< 3 ns from rising edge
> 3 ns from rising edge
Dynamic Range
(< 1.5% gain compression)
dc Offset Accuracy
Offset Adjustment Range
Offset Gain
RMS Output Noise
(dc to 2.5 GHz with
input loaded in 50 Ω)
Propagation Delay
Maximum Input Voltage
ESD Tolerance (150 Ω/150 pF)
Power Requirements
from AutoProbe Interface
Net Weight
Safety
>2.5 GHz
1.3 GHz
500 MHz
<140 ps calculated from tr =
(0.35/bandwidth)
10:1
100 kΩ±1%
±0.5%
0.6 pF (typical)
±6%
±1%
±5 V dc + peak ac
±1% of offset ±1 mV
±20 V at the probe tip
4.6 V/mA
< 300 µV
7.5 ns (approximately)
±40 V (dc + peak ac (< 20 MHz)),
CAT I
±12 kV
+12 V @ 5 mA max
-12 V @ 95 mV max
+4 V @ 90 mA max
4.9 oz
Meets IEC1010-2-31
Environmental Characteristics
Temperature (Operating)
Humidity (Operating)
0° C to +55° C
Up to 95% relative humidity
at 40° C
* Denotes specified parameters. All others are characteristics.
Ordering Information
HP 1152A Active Probe
Each HP 1152A includes:
1 walking stick ground (HP 5960-2491),
5 single-contact sockets (HP 1251-5185), 1, 2-inch ground wire,
attachable to walking stick (HP 01650-82103), 1, 4-inch alligator
ground wire, attachable to probe tip ground (HP 01123-61302),
1 standard replacement tip (HP 54701-26101), 2 sharp probe
tips (HP 5081-7734), 1 200-Ω signal lead (HP 54701-81301),
1 User and Service Guide, and a one-year warranty.
7
HP 1153A 200 MHz Differential
Probe for HP Infiniium Oscilloscopes
High-bandwidth probing for
differential signals
• Dc to 200-MHz bandwidth
• AutoProbe Interface compatible
• ±200 V (dc + peak ac) maximum
allowable input without
attenuators
• 3000:1 CMRR at 1 MHz
• Low frequency reject
• Superior tolerance to ESD
• Low dc thermal drift
• Rugged construction
HP 1153A probe and accessories
• Easy-to-attach, snap-on BNC
The HP 1153A is a 1:1 FET
differential probe with 200 MHz
bandwidth and 3000:1 CMRR
(Common Mode Rejection Ratio)
at 1 MHz. The probe has an input
resistance of 1 MΩ and low input
capacitance of 7 pF to minimize
circuit loading.
DC/Lf Reject
Typical:
DC/Lf Reject
Minimum:
10000:1
5000:1
2000:1
1000:1
10:1 attenuator
100:1 attenuator
AutoProbe Interface Compatible
The HP 1153A is compatible with
AC Coupler
the HP AutoProbe Interface
which completely configures the
HP Infiniium Oscilloscope for the
probe. The probe interface recognizes the
probe and automatically sets up the proper
power, coupling modes, 50 Ω impedance and
offset range.
100:1
10:1
3:1
1:1
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
10 MHz
100 MHz
Low dc Thermal Drift
The probe’s dual-path amplifier design provides
superior dc stability by reducing dc drift to less
than 50 µV dc per °C.
Reliability
Attenuators, ac Coupling
The HP 1153A is designed for reliability
through use of over-voltage protection circuitry
which decreases the probe’s susceptibility to
damage from electrostatic discharge and other
accidental exposure to excessive voltage.
Two attenuators, 10:1 and 100:1, are provided
to expand the dynamic range of the inputs up
to ±30 V. It also comes with an ac coupling
adapter for those cases where input dc voltage
level prevents you from using low frequency
reject.
We also designed the HP 1153A to be rugged.
We paid special attention to isolating critical
parts from shock. With a shell molded of tough
ABS-polycarbonate, the HP 1153A is built for
long life and dependability.
Low Frequency Reject
Lf reject, like ac coupling, blocks the dc
component in a signal without degrading lowfrequency CMRR, which occurs when you use
blocking capacitors to accomplish ac coupling
(see the graph above).
8
Environmental Characteristics
Characteristics
Bandwidth (-3dB)*
System Bandwidth HP 54800 Family
Risetime
(0.35/bandwidth)
dc Gain Accuracy*
(with 50 ± 0.1 Ω load)
dc Attenuator Accuracy
Linear Differential Input Range
dc Offset
dc to 200 MHz1
200 MHz
1.75 ns calculated from tr =
2%
2%
±0.3 V (1:1) ; ±3.0 V (10:1)
±30 V (100:1)
±18 V (1:1); ±180 V (10:1)
±500 V (100:1)
Common Mode Operating Range
dc: ±18 V (1:1); ±180 V (10:1)
±500 V (100:1)
dc to 30 Hz: linearly decreased to
30 Hz value.
30 Hz to 200 MHz: ±0.5 V (1:1); ±5 V (10:1);
±50 V (100:1)
(voltages are peak voltage)
Maximum Allowable Input Voltage* 200 V (dc + peak ac) CAT I, 1:1
500 V (dc + peak ac) CAT I,
with attenuators common or
differential modes
Input Coupling
dc, lf reject, and ac.
Ac coupling is provided via an
adapter that attaches to the
probe. Lf reject response (-3dB)
is selectable independent of
attenuators at 1.7 Hz (LFR1)
and 0.14 Hz (LFR2)
CMRR*
See graph on previous page
ac Coupling
15 Hz (1:1); 1.5 Hz (10:1)
Low-Frequency Response (-3dB)
w/ac coupling adapter and input 1.5 Hz (100:1)
coupling set to dc
dc Thermal Drift
≤ 50 µV dc/°C
Input RC
R
C
1:1 1 MΩ
7 pF
10:1 9 MΩ
3.5 pF
100:1 10 MΩ 2.0 pF
Output Termination Impedance
50 Ω
Power Requirements from the
+12 V @ 33 mA max
AutoProbe Interface
-12 V @ 16 mA max
+6 V @ 80 mA max
-6 V @ 130 mA max
Safety
Meets IEC 1010-2-31
Temperature Operating
Non-operating
Humidity
Operating
Non-operating
Altitude
Operating
Non-operating
0° C to +55° C
-40° C to +70° C
95% relative humidity at 40° C
90% relative humidity at 65° C
up to 4,600 m (15,000 ft)
up to 15,300 m (50,000 ft)
* Denotes specified parameters. All others are characteristics.
1 For maximum signal fidelity, above 100 MHz, limit probe output into
50 Ω to ≤ 300 mV peak to peak.
Ordering Information
HP 1153A Differential Probe
Each HP 1153A includes: 2 voltage attenuators, 10:1 and 100:1,
ac coupling adapter, 5 probe leads, 2 probe clips, Operating and
Service Manual, calibration adapter, ground lead, and one-year
warranty.
Accessories
HP 5959-9335 Long (5.5”) test lead, Qty. 5
HP 5090-4356 SMD clips, Qty. 20
HP 10467-68701 0.5 mm IC clips for surface
SMT parts with leg spacing of 0.5mm (.020”)
to 0.8mm (.032”), Qty. 4
9
The HP 1155A
Low Mass Active Probe
• Small and light probe tip
(< 1 gram)
• < 2pF input capacitance
and 1 MOhm impedance
• 750 MHz bandwidth
• 2 channels
• Autoprobe interface
Small, low mass probe tip
for surface mount devices
Talk about big performance in a
small package! The two-channel
HP 1155A low-mass active probe
for HP Infiniium oscilloscopes
combines a probe tip that weighs
less than 1 gram with the superior performance
of an active probe. It's a powerful combination
ideal for attaching to fine-pitch ICs and probing
surface mount components.
More power to you
The 1155A probe couples high band width
(750 MHz), low input capacitance (2 pF), and
high resistance (1 MΩ). It's a combination
superior to passive divider probes with higher
input capacitance, because it provides minimal
circuit loading at high and low frequencies.
Includes the HP Wedge.
Provides hands-free probing.
The HP 1155A comes complete with the
HP Wedge Probe Adapter for hands-free
probing of 0.5 mm ICs. The HP Wedge
provides accurate, mechanically noninvasive
and reliable electrical contact with little chance
of shorting. It's easy to insert and it stays put.
Typical Input Impedance vs. Frequency
1M
100k
HP 1155 A
10k
HP 1160A
1k
100
10k
100k
1M
10M
Frequency (Hz)
100M
1G
10
Characteristics
Bandwidth (-3dB)
System Bandwidth with
HP 54800 Family
Risetime
Attenuation Factor
dc Input Resistance
Input Capacitance
Flatness
Input Dynamic Range
Maximum Input Voltage
Ordering Information
dc to ≥ 750 MHz
750 MHz
≤ 470 ps
10:1 ± 3%
1 MΩ ± 2%
2 pF (typical)
Less than ± 10% for first 6ns,
± 4% from 6ns to 20 µs,
± 1.5% thereafter
0 to 6.0 V
±40 V (dc + peak ac), CAT I
Environmental Characteristics
Temperature (Operating)
Humidity (Operating)
0° C to +55° C
Up to 95% relative humidity
at 40° C
* Denotes specified parameters. All others are characteristics.
Fine Pitch IC Probing Accessories
HP 1155A Low mass, 2-channel active probe.
Each HP 1155A includes: 4 probe pins, 5 SMT clips,
2 flexible leads, 2 spacing ground adapters,
2 red and black SMT leads, 1 BNC-to-probe tip adapters,
2 0.5 mm HP Wedge Probe adapters
HP E2613B HP Wedge probe adapter,
.5mm, 3-signal, Qty 2.
HP E2614A HP Wedge probe adapter,
.5mm, 8-signal, Qty 1
HP E2615B HP Wedge probe adapter,
.65mm, 3-signal, Qty 2
HP E2616A HP Wedge probe adapter,
.65mm, 8-signal, Qty 1
HP10467-68701 0.5mm IC clips for
surface SMT parts with leg spacing of .5mm
(.020") to .8mm (0.32 "), Qty 4
Other Accessories
HP E9638A Probe tip to BNC (m) adapter
11
HP Wedge Probe Adapter
• Easy connection to
surface mount IC’s
• Safe, with no chance of
shorting
• Mechanically noninvasive contact
• Three and eight signal
versions
• Supports 0.5mm and
0.65 mm TQFP and
PQFP packages
Make the inaccessible
accessible with this
non-invasive, problem-free
probing solution
Making the inaccessible accessible
If you've ever tried to probe a surface mount
component, you've probably experienced one
or more of the following frustrating situations:
Accidentally shorting IC pins together;
electrical and/or mechanical problems with
soldering small wires onto leads; and/or holding
multiple probes and trying to use your scope at
the same time. The HP Wedge Probe Adapter
provides a solution to these frustrations.
The HP Wedge easily attaches to HP Infiniium
probes. It connects directly to the HP 1155A
and the HP 1170A-family of low mass probes
and the dual lead adapter provided with the
HP 1160A-family of miniature passive probes.
Problem-free probing
Characteristics
There's no need to worry about accidentally
shorting IC pins together on a delicate
component –or worse yet on an irreplaceable
prototype. The Wedge is easy to insert and it
stays put. There's no need to solder small wires
onto leads. The Wedge is mechanically noninvasive, so you won't damage the legs of the
IC. Instead, you'll have easy access to hard-toreach components. And that makes testing
them hassle-free.
Operating Voltage
Operating Current
Capacitance Between Contacts
Self-Inductance
Contact Resistance
Electrical reliability
The HP Wedge makes two contact points with
each leg of the IC. This redundant physical
connection increases the electrical reliability of
the connection. In the HP Wedge’s low
capacitance and inductance provides superior
performance to many other alternatives.
For more information on how the HP Wedge
Probe Adapter works with your HP Infiniium
scope, please refer to application note
5966-4179.
<40 V dc + peak ac
0.5 A maximum
2 pF (typical)
15 nH (typical)
<0.1 Ohm
Ordering Information
HP Wedge Probe Adapter
HP E2613B 0.5 mm, 3 signal, qty 2
HP E2614A 0.5 mm 8 signal, qty 1
HP E2615B 0.65 mm, 3 signal, qty 2
HP E2616A 0.65 mm, 8 signal, qty 1
Each HP Wedge includes: 1 user's guide and 1 magnifying lens
Accessories
The HP 1160-family of oscilloscope probes come with a dual
lead adapter. Additional adapters can be ordered. Use the
HP 5063-2147 dual lead adapter for HP 116x probe family
12
0.5 mm IC clips
General Purpose BNC Adapters and Feedthrough Terminations
HP 10467-68701
0.5 mm IC Clips
• Smallest IC clips in the
industry to date
• Probe PQFP and SOIC SMT
packages from 0.5 mm to
0.8 mm (0.020" to 0.032")
lead pitch
• Thin clip body allows many
IC clips to be mounted
side-by-side
The 0.5 mm IC clips easily
attaches to HP Infiniium probes.
They connect directly to the
HP 1155A and the HP 1170Afamily of low mass probes and the dual lead
adapter provided with the HP 1160A-family of
miniature passive probes.
HP 10467-68701 Characteristics
Length
Tip diameter
Pin diameter
31.75 mm (1.25 in.)
.75 mm (.029 in.)
.75 mm (.029 in.)
Ordering Information
HP 10467-68701 0.5 mm IC clips, pkg of 4
BNC Adapters and
Feedthrough terminations
Not all BNC adapters and feedthrough
terminations are the same and making a bad
choice can have a big impact on your
measurement. That’s why HP adapters and
connectors are the choice of many
professionals the world over who demand
excellence in their measurement set up.
Feedthrough terminations
HP 10100C BNC (m) to BNC (f) 50 Ohm high performance
feedthrough
HP 11094B BNC (m) to BNC (f) 75 Ohm feedthrough
BNC to BNC adapters (50 Ohm)
HP E9620A BNC (m) to BNC (f) Ohm right angle
HP E9622A BNC (f) to BNC (f) Ohm
HP E9624A BNC (m) to BNC (m) Ohm
HP E9625A Tee BNC (m) (f) (f)
BNC to BNC adapters (75 Ohm)
Impedance
Typical BNC Connector Impedance
75Ω
50Ω
100kHz
HP E9628A BNC (f) to BNC (f)
HP E9629A BNC (m) to BNC (m)
Between series adapters (50 Ohm)
1 Mhz
10 MHz 100 MHz 750 MHz
Frequency
Accuracy: 1 MHz to 100 MHz:
100 MHz to 300 MHz:
300 MHz to 500 MHz:
50Ω/75Ω ± 1%
50Ω/75Ω ± 3%
50Ω/75Ω ± 5%
HP E9621A Type N (f) to BNC (m)
HP E9623A Type N (m) to BNC (m)
HP E9635A Type N (m) to BNC (f)
HP E9631A SMA (m) to BNC (f)
HP E9632A SMA (f) to BNC (m)
HP E9633A SMA (m) to BNC (m)
HP E9634A SMA (f) (gold plated) to BNC (m)
HP E9636A SMC (m) to BNC (m)
HP E9626A SMC (f) to BNC (f)
HP E9627A Banana (f) to BNC (m)
HP E9637A BNC (f) to dual banana (m)
13
Input devices for
HP Infiniium Oscilloscopes
HP E2611A Clip-on Trackball
If you don't have the benchspace for a
standard mouse, a clip-on trackball is available
for HP Infiniium. The trackball clips into holes
on the instrument. The driver for the clip-on
trackball is pre-installed.
HP E2610A Keyboard
The E2610A is a small keyboard for use with
HP Infiniium Oscilloscopes. The keyboard
makes file naming easier if you are archiving
waveforms or instrument setups. You'll
appreciate the small size of this keyboard for
use on your bench or on an oscilloscope cart.
HP E2612A Touchpad
The E2612A Touchpad has a touch surface that
gives you complete control of your scope with
just the tip of your finger. The driver for the
Touchpad is pre-installed.
Ordering Information
HP E2611A Clip-on Trackball
HP E2610A Keyboard
HP E2612A Touchpad
14
Rack or Pack Your
HP Infiniium Oscilloscopes.
HP E2609A Rackmount Kit
The rackmount kit provides a support shelf
and hardware for mounting Infiniium into EIA
standard [19-in (487-mm)] rack cabinets.
When installed, the instrument occupies 5
vertical increments [8.75 in (222 mm)].
HP 1182B Testmobile
The 1182A is a testmobile for use with
HP Infiniium Oscilloscopes. Large, easy-tomaneuver wheels let you move your scope with
ease from place to place. Supports monitor and
printer with sliding drawer for accessories.
HP 2609A Rackmount Kit
HP 1184A Testmobile
Made tough for years of sturdy performance,
the HP 1184A Testmobile features large wheels
that get you where you want to go in no time with no tipping. Includes bottom drawer for
accessories, slide-out mouse tray for right- or
left-handed operation, and support for monitor
and printer.
Ordering Information
Rackmount Kit
HP E2609A Rackmount Kit
Each kit includes: a support shelf, 2 rackmount rails,
1 Touchpad (E2612A), 2 brackets, hardware,
and a user's reference.
Rackmount Accessories
1494-0015 Rackmount slide kit
Testmobile
HP 1182B Testmobile
HP 1184A Testmobile
Testmobile Accessories
HP 1184A Testmobile
HP E2617A Transit Case
The HP E2617A Infiniium Oscilloscope Transit
Case is one heavy-duty, hard cover carrying
case. Ideal for transporting oscilloscopes away
from the lab, it's constructed from rugged
A.B.S. with rubber-grip, steel handles and steel
latches. Pull-out handles and smooth-rolling
wheels make moving your instrument easy.
The case can also be padlocked (not included).
HP 35181H Printer/Plotter stand
HP 35181K Work surface (550 x 305 mm)
HP 35181E Antistatic Mat for 35181D
HP 35181J 89 mm (3.5 in) high Storage Drawer,
Support shelf
HP 35181M 133 mm (5.25 in) high Storage Drawer,
Support shelf
HP 92199B Power Strip (U.S.) (5 receptacles)
HP 92199E Power Strip (IEC 320)(4 receptacles)
International use of 92199E requires one or more of
the cable assemblies below:
HP 8120-1575 Cable, 762 mm (30 in)
HP 8120-2191 Cable, 1.5 m (60 in) with
right angle plug
HP 5181-8707 IEC-320 Male Power Cable Adapter
Transit Case
HP E2617A Infiniium Transit Case
15
Other Probes Compatible
with HP Infiniium Oscilloscopes
HP 1144A 800-MHz Active Probe
Request Technical Data Sheet 5091-7935
(requires HP 1142A power supply)
HP 01144-61604 probe power extender
(required when using more than 2 HP 1144A active probes)
$ 42.00 ea.
HP 1145A 2-channel, 750-MHz Active Probe for SMD
Request Technical Data Sheet 5962-8537
(requires HP 1142A power supply)
HP 1146A Oscilloscope AC/DC Current Probe
Request Technical Data Sheet 5965-5689
HP 1137A 1000:1 High-Voltage Probe
Request Technical Data Sheet 5952-2410
For more information about HP Infiniium Probes and
Accessories, HP Infiniium Communication Mask Testing
option, HP Infiniium oscilloscopes, or other Hewlett-Packard
Test and Measurement products, and for a current sales office
listing, visit our web site at
http://www.hp.com/info/infiniium21.
You can also contact one of the following centers and ask for
a test and measurement sales representative.
United States:
Hewlett-Packard Company
Test and Measurement Call Center
P.O. Box 4026
Englewood, Colorado 80155-4026
1 800 452 4844
Canada:
Hewlett-Packard Canada Ltd.
5150 Spectrum Way
Mississauga, Ontario
L4W 5G1
(905) 206 4725
Europe:
Hewlett-Packard
European Marketing Centre
P.O. Box 999
1180 AZ Amstelveen
The Netherlands
(31 20) 547 9900
Japan:
Hewlett-Packard Japan Ltd.
Measurement Assistance Center
9-1, Takakura-Cho,
Hachioji-Shi,
Tokyo 192, Japan
Tel: (81) 426 56 7832
Fax: (81) 426 56 7840
Latin America:
Hewlett-Packard
Latin American Region Headquarters
5200 Blue Lagoon Drive
9th Floor
Miami, Florida 33126
U.S.A.
Tel: (305) 267-4245
(305) 267-4220
Fax: (305) 267-4288
Australia/New Zealand:
Hewlett-Packard Australia Ltd.
31-41 Joseph Street
Blackburn, Victoria 3130
Australia
1 800 629 485
Asia Pacific:
Hewlett-Packard Asia Pacific Ltd.
17-21/F Shell Tower, Times Square,
1 Matheson Street, Causeway Bay,
Hong Kong
Tel: (852) 2599 7777
Fax: (852) 2506 9285
Data subject to change.
Windows is a registered trademark of
Microsoft Corporation.
© Hewlett-Packard Company 1999
Printed in the U.S.A. 2/99
5968-3832 EN
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement