Avlite FAA L-864 AV-OL-FL864-12-R, AV-OL-FL864-UM-R Obstruction Light Installation & Service Manual
Below you will find brief information for FAA L-864 AV-OL-FL864-12-R, FAA L-864 AV-OL-FL864-UM-R. FAA L-864 AV-OL-FL864-12-R and FAA L-864 AV-OL-FL864-UM-R are medium intensity LED obstruction lights certified to the FAA L-864 Medium Intensity Obstruction Lighting advisory circular 150/5345-43. They can be used to mark obstacles such as telecommunication and utility towers, wind turbines, cranes, buildings and other tall structures.
PDF
Download
Document
Advertisement
Advertisement
AV-OL-FL864-12-R & AV-OL-FL864-UM-R FAA L-864 Medium Intensity Obstruction Light Universal DC & Universal AC Models Installation & Service Manual Version 1.3 Version No. 1.0 1.1 1.2 1.3 Description Manual launch Spec table update Warranty update Update installation & wiring Date March 2015 March 2015 March 2015 June 2015 Approved W. Evans J. Dore W. Evans W. Evans FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Table of Contents Introduction........................................................................................................ Page 4 Technology......................................................................................................... Page 4 AV-OL-FL864-12-R & AV-OL-FL864-UM-R Models.......................................... Page 5 Safety Information............................................................................................. Page 8 Unpacking, installation, wiring & setup.......................................................... Page 9 Unpacking............................................................................................... Page 9 Installation & Wiring................................................................................. Page 9 Operation & Setup................................................................................. Page 12 Intensity Setting.................................................................. Page 12 Alarm Relay Output............................................................ Page 12 Momentary Button operation.............................................. Page 12 RS232 and RS422/485 Communication (optional)............ Page 13 Optional IR Remote Control..............................................................Page 14 Avlite IR Controller / Universal Remote Compatibility................Page 14 IR Controller Functions...............................................................Page 15 Test Mode / Configure................................................................. Page 15 Normal Operation........................................................................ Page 15 Read............................................................................................ Page 15 Operational Mode........................................................................ Page 16 Battery Status.............................................................................. Page 16 Error/Acknowledge Indication...................................................... Page 16 Optional GPS Synchronisation...................................................................... Page 17 Optional GSM Monitoring & Control.............................................................. Page 18 Maintenance & Servicing................................................................................ Page 19 Trouble Shooting............................................................................................. Page 19 Lantern Status................................................................................................. Page 20 Certifications & Compliance.......................................................................... Page 21 Avlite Light Warranty....................................................................................... Page 22 Latest products and information available at www.avlite.com 3 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Introduction Congratulations! By choosing to purchase an Avlite light, you have become the owner of one of the most advanced LED obstruction lights in the world. Avlite Systems draws on more than 25 years experience in the design and manufacture of navigation aids, and particular care has been taken to ensure your light gives years of trouble free service. As a commitment to producing the highest quality products for our customers, Avlite has been independently certified as complying with the requirements of ISO 9001:2008 quality management system. By taking a few moments to browse through this booklet, you will become familiar with the versatility of your light, and be able to maximise its operating function. Please remember to complete the Avlite warranty registration card accompanying your light. Technology Avlite Systems is a world-class solar lighting systems manufacturer with a proven reputation for rapid, innovative, and agile technology solutions designed specifically for defense, government, civil and humanitarian aid operations in the most remote, toughest environments. Electronics Avlite employs leading in-house electronic engineers in the design and development of software and related circuitry. All individual electronic components are sourced directly by Avlite procurement staff ensuring that only the highest quality components are used in our products. LED Technology All Avlite lights use the latest advancements in LED (Light Emitting Diode) technology as a light source. The major advantage of LED’s over traditional light sources is well established in that they typically have an operational life in excess of 100,000 hours, resulting in substantial savings to maintenance and servicing costs. Precision Construction Commitment to investing in the design and construction of injection-moulded parts including optic lenses, light bases and a range of other components ensures that all Avlite products are of a consistent and superior quality. Optical Performance Avlite manufactures a range of aviation LED lenses moulded from multi-cavity dies. The company has superior in-house lens manufacturing capabilities to support outstanding optical performance. Award-winning, Patented Technology Several United States and Australian patent registrations are held on Avlite’s range of innovative designs, with other regional patents pending in Canada, United Kingdom and Europe. Latest products and information available at www.avlite.com 4 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models AV-OL-FL864-12-R & AV-OL-FL864-UM-R Medium Intensity Obstruction Light This Avlite medium intensity LED obstruction light is certified to the FAA L-864 Medium Intensity Obstruction Lighting advisory circular 150/5345-43. The light is used to mark obstacles such as telecommunication and utility towers, wind turbines, cranes, buildings and other tall structures. Avlite’s LED obstruction lights offer an ultra bright, energy efficient and cost effective lighting solution. The light fixture is available in two configurations, universal DC (12–48VDC) or universal AC (110–240VAC). The light fixture incorporates internal diagnostic checking and an alarm contact for remote monitoring. The alarm relay is energised in normal operation and is released if there is an LED or power fault. Latest products and information available at www.avlite.com 5 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Impact modified UV-stabilised acrylic lens Multiple LED Optic Automatic night operation 7-stage powder coated aluminium base 104 (4.09”) 151 (5.94”) 200mm bolt pattern for ease of installation 230 (9.06”) PCD 200 (7.87”) 6 Places Latest products and information available at www.avlite.com 6 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models SPECIFICATIONS•* 12–48 VDC 110–240VAC AV-OL-FL864-12-R AV-OL-FL864-UM-R Red as standard. Other colors available on request 2000cd ± 25% 360 3o 0.5s ON, 2.5s OFF – 16.6% duty cycle Red as standard. Other colors available on request 2000cd ± 25% 360 3o 0.5s ON, 2.5s OFF – 16.6% duty cycle 12 – 48 VDC 6W 36W Integrated -40 to 80°C 110 – 240VAC 50/60Hz Pmax: 6W, Smax: 8VA Pmax: 36W, Smax 48VA Integrated -40 to 80°C 7-stage powder-coated aluminium Impact modified UV stabilized acrylic 171 / 6¾ Multi LED Optic 200mm bolt pattern 151 / 6 230 / 9 5.5 / 12¼ Up to 12 years 7-stage powder-coated aluminium Impact modified UV stabilized acrylic 171 / 6¾ Multi LED Optic 200mm bolt pattern 151 / 6 230 / 9 5.8 / 12¾ Up to 12 years 0 to 100%, MIL-STD-810F 22kg per square inch Up to 240kph 0 to 100%, MIL-STD-810F 22kg per square inch Up to 240kph EN61000-6-3:1997. EN61000-6-1:1997 ISO9001:2008 IP67 EN61000-6-3:1997. EN61000-6-1:1997 ISO9001:2008 IP67 AVLITE® is a registered trademark of Avlite Systems 4 year warranty AVLITE® is a registered trademark of Avlite Systems 4 year warranty • Variety of solar/battery configurations • GSM Cell-Phone Monitoring • GPS Synchronisation • RS422/485 communications port • GSM Cell-Phone Monitoring • GPS Synchronisation • RS422/485 communications port Light Characteristics Available colors Effective Intensity (cd)† Horizontal Output (degrees) Vertical Divergence (degrees) Available Flash Characteristics Electrical Characteristics Operating Voltage Power (Average Flashing) Power (Peak) Circuit Protection Temperature Range Physical Characteristics • Specifications subject to change or variation without notice * Subject to standard terms and conditions † Intensity setting subject to solar availability Body Material Lens Material Lens Diameter (mm/inches) Lens Design Mounting Height (mm/inches) Width (mm/inches) Mass (kg/lbs) Product Life Expectancy Environmental Factors Humidity Icing Wind Speed Certifications CE Quality Assurance Waterproof Intellectual Property Trademarks Warranty * Options Available Latest products and information available at www.avlite.com 7 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Safety Information • Install the light in compliance with the effective local electrical code(s). • Mains power should always be disconnected when work is being done in close proximity to electrical fittings, and electrical work should only be done by a licensed electrician. • Operate the light only within the indicated electrical ratings and product usage instructions. • To ensure that the light and peripheral equipment function safely and correctly, use cable in compliance with the effective local electrical code. • Do not stare at the LED or shine the LED into your eyes or those of another person. • Do dispose of the product according to the local laws and regulations for your region, for example, at a recycling center that accepts electronic devices. Latest products and information available at www.avlite.com 8 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Unpacking, Installation, Wiring & Setup Unpacking Unpack all hardware and inspect for damage. If there is any damage, please contact your Avlite Office. Retain original packing material for possible future use in shipping. Installation & wiring Before proceding with installation or service, make sure the following conditions are met: • Ensure the tower or mast is grounded (NO RF HAZARD) • Check the mast lighting circuit is not faulty • Ensure power lines are not ‘live’ (NO ELECTRICAL HAZARD) • Avoid touching live circuits! • Avoid touching any component or any part of the circuitry while the unit is operating. Do not changecomponents or make adjustments inside the unit with power on. • In AC installations, where upstream circuit breakers are utilized, use a 30A Type C breaker. NOTE: The obstruction light is manufactured with an input power cable of length defined at the time of order. One end of the input power cable is pre-terminated at the light fixture. Connect the provided input power cable to the corresponding power source in accordance with figure 1 for AC installations and figure 2 for DC installations. Latest products and information available at www.avlite.com 9 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models AC Wiring Configuration AC WIRING CONFIGURATION External: Active/Live Neutral Earth Active/Live (L1) Australia/ Europe/ UK USA/ Canada Brown Black Australia/ Europe/ USA/ Canada White Blue UK Green/Yellow Green Brown Black Neutral (L2) Blue White Earth Green/Yellow Green Cable: 3-core Internal: FL864 AC Wiring Diagram LED driver LED DC Wiring Configuration Positive uP Negative Brown Blue Light in normal operation AC/DC POWER 1 2 3 RS232 ALARM 4 5 6 7 8 9 RS422 IO-1 10 11 12 13 14 15 16 17 18 19 Cable: 2-core Momentary Button Figure 1. Latest products and information available at www.avlite.com 10 NO. CONNECTOR SIGNAL 1 POWER L1 2 POWER L2 3 POWER GND 4 ALARM COMM 5 ALARM NO 6 ALARM NC 7 RS232 GND 8 RS232 RxD 9 RS232 TxD 10 RS422 GND 11 RS422 -VE (Rx) 12 RS422 +VE (Rx) 13 RS422 -VE (Tx) 14 RS422 +VE (Tx) 15 IO-1 3V3 16 IO-1 OUT-1 17 IO-1 0V 18 IO-1 IN-1 19 IO-1 0V FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models DC Wiring Configuration DC WIRING CONFIGURATION Positive Brown Blue External: Negative Positive (+VDC) Brown Negative (-VDC) Blue Cable: 2-core Internal: FL864 DC Wiring Diagram LED driver LED uP Light in normal operation DC/DC POWER 1 2 3 RS232 ALARM 4 5 6 7 8 9 RS422 IO-1 10 11 12 13 14 15 16 17 18 19 Momentary Button Figure 2. Latest products and information available at www.avlite.com 11 NO. CONNECTOR SIGNAL 1 POWER +VBatt(+VDC) 2 POWER -VBatt(-VDC) 3 POWER UNUSED 4 ALARM COMM 5 ALARM NO 6 ALARM NC 7 RS232 GND 8 RS232 RxD 9 RS232 TxD 10 RS422 GND 11 RS422 -VE (Rx) 12 RS422 +VE (Rx) 13 RS422 -VE (Tx) 14 RS422 +VE (Tx) 15 IO-1 3V3 16 IO-1 OUT-1 17 IO-1 0V 18 IO-1 IN-1 19 IO-1 0V FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Operation & Setup When powered up, the light will constantly check day/night status using its internal ambient light sensor. The ambient light sensor averages its measurement for 30 seconds. FAA: By default the lights turn ON when the ambient light decreases to not less than 35 footcandles (367.7 lux) and turn OFF when the ambient light increases to not more than 60 footcandles (645.8 lux). These limits can be factory adjusted, if required. INTENSITY SETTING The fixture will be supplied with a FAA compliant optic. The obstruction light will be pre-set to the intensity setting required to produce a FAA compliant photometric profile. The intensity is pre-set in the factory and does not need to be set by the user. ALARM RELAY OUTPUT In normal operation the relay is energised • Terminal contacts COMM and NC of the relay are electrically closed • Terminal contacts COMM and NO of the relay are electrically open Whenever the LED is not lit due to a power failure and/or a LED failure the relay will not be energised. • Terminal contacts COMM and NO of the relay are electrically closed • Terminal contacts COMM and NC of the relay are electrically open The alarm relay comes configured as follows: • Relay normal operation (default, as described above) The following alarm relay configurations are available as a special order. These must be specified at the time of order: • Relay inverse operation (inverse functionality of the normal operation, used to conserve power) • Relay disable (in case the relay is not required, used to conserve power) NOTE: The alarm relay is intended for low voltage (SELV) connection only. NOT FOR MAINS CONNECTION MOMENTARY BUTTON OPERATION The AV-OL-FL864 light is fitted with an external momentary button for manual light operation. The momentary button is incorporated for maintenace, testing and emergency use, this button allows the user to cycle between ‘forced on’ and ‘forced off’ mode irrespective of the current ambient light conditions. A momenary button mode change remains active for 4 minutes and then the light reverts to the factory default operation of ‘dust-till-dawn’. To use the momentary button: 1. Hold down the push button for 3 seconds (the light will be forced on again). 2. Press the momentary button again and the light will be forced off. 3. Additional button presses will cycle between these two modes. Latest products and information available at www.avlite.com 12 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models RS232 AND RS422/485 COMMUNICATION (OPTIONAL) The Obstruction Light offers a RS232 and a R2422/485 interface. RS232 Typical 3 pin TxD, RxD and GND arrangement RS422/485 Typical 4 pin arrangement with Termination selection and Duplex/Simplex selection For location details please refer to Figure 1 & 2. Duplex SW3 Termination SW4 S1 S2 S1 S2 OFF OFF Simplex operation OFF OFF No termination ON ON Duplex operation ON ON 120 Ohm termination Please contact Avlite for further details. Latest products and information available at www.avlite.com 13 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Optional IR Remote Control The IR remote is used to communicate with Avlite lighting products that have an IR sensor fitted. The remote control is used for the following functions: Test / Configure • Operational Mode: dusk-to-dawn, standby or always-on. • Ambient Light Thresholds: read the current light thresholds, configure new ambient light thresholds. • Perform a battery health check. On receiving a valid key signal from the IR Remote, the light will flash once. The user should wait until the light responds to each keypress before pressing another key. If there is no response to the keypress after 3 seconds, it has not been detected by the light and the key can be pressed again. If an invalid key is detected, the light will flash quickly 5 times. In this case, the command will have to be restarted. T/C 1 2 3 4 5 6 7 8 9 Read Lux R 0 L Flash Code Intensity Battery Status FC I B Avlite IR Controller / Universal Remote Compatibility If you lose your Avlite IR Controller, the following Universal Remote Controller has been tested for compatibility: RCA Type RCR312WR programmed for Phillips TV Type Code 10054 Avlite Key Universal Remote Key T Power 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 0 R Channel+ L Mute FC Volume+ I Volume- B ChannelLatest products and information available at www.avlite.com 14 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models IR Controller Functions Test Mode / Configure T/C 1 Pressing the T/C button for up to 5 seconds places the light in Test Mode. The light will flash once in response to the T/C button being pressed and then turn off. 2 3 4 5 6 7 8 T/C 9 R 1 L 02 T/C Normal Operation 3 FC 4 The light will return to normal operation once it has not detected a valid key press for 30 seconds. The light will flash once to indicate it is returning to normal operation. B 1I 2 3 5 6 T/C T/C T/C T/C Read Pressing the Read 6 4 5 7 8 9 1 2value. 3followed3by one of the configuration keys shall cause the light to flash the 1 2 3 1 configured 2 T/C 3 1 2 Example Key Sequences: 7 8 9 R L 0 4 5 6 4 5 6 1 2 3 4 5 6 4 5 6 R L The light flashes the current battery status. 0 FC I B T/C 7 8 9 7 8 9 4 5 6 7 8 9 7 8 9 The flashes the sunset level in Lux, followed by a 2 second gap, followed FC I B 1 2 3light R 0 R 0 7 8LL T/C 9L by the R 0 R L sunrise level. Levels are in the range of 1 to 9. 0 4 5 6 BLI T/C FC B 1 2 3 The light flashes the Operational Mode. Modes are as follows: RII 0 FC FC BI FC B 1 flash = Always-On 2 flashes = Standby 7 8 9 4 5 6 FC I 1B 2 3 flashes 3 = Dusk-to-Dawn R L 0 7 48 59 6 FC I B R 70 8L 9 FC RI 0B L FC I B Latest products and information available at www.avlite.com 15 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Operational Mode The light has three modes of operation: Always on, Standby Mode and Dusk-to-Dawn mode. These modes can be selected either via the IR remote control or via the GSM module (if fitted). In Always On mode, the daylight sensor is disabled and the lantern will remain ON. In Standby mode, the lantern is turned off and the daylight sensor is disabled. This mode does not affect the operation of the GSM module. In Dusk-to-Dawn, the daylight sensor is enabled. T/C 2 5 8 0 I 1 4 B L 3 L B 6 L B 9 1 T/C Always on mode 2 T/C Standby mode 3 T/C Dusk-to-Dawn mode Battery L Status (12V system only) T/C B 2 T/C 3 This function reads the battery status. The response from the light is: 1 5 2 6 3 4 flashes = High Voltage 3 flashes = Good Voltage 2 flashes = Low Voltage 4 5 6 8 9 T/C 7 Key 8L 9 R 0 1 Example 2 3 sequence: RI L 0 FC B T/C 4 5 6 2B Indication 3 FC 1I 7 Error/Acknowledge 8 T/C 9 If the key sequence is invalid, or an out of bounds value is attempted to be set, the light flashes 5 times 4 (The command 5 6 then needs to be sent from the start.) for 1 second. 1 2L sequence: 3 (Set the intensity level to 5 – undefined.) R Example 0 key 7 8 9 5B T/C 6 FC 4I R L 0 The 1 5 times 7light flashes 8 92 for 31 second. When a key sequence has been entered successfully the light will respond acknowledgement with a 1 FC I B second flash. R L 04 5 6 7 1 flashes = Cutoff Voltage or below FC 7I Latest products and information available at www.avlite.com B 8 9 16 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Optional GPS Synchronisation Avlite has utilized the latest advancements in GPS technology to develop an internal synchronisation system that can be incorporated into the lights. Using overhead satellites, multiple obstruction lights set to the same flash pattern will flash in unison. No additional power supplies, aerials or control systems are required, and with its microprocessorbased system, the GPS option is specifically designed to provide maximum reliability and performance over a wide range of environmental conditions. OPERATING PRINCIPLE Each light operates independently and requires no operator intervention. A minimum of 4 satellites need to be in view for the built-in GPS receiver to collect time data. At dusk, the light sensor will turn the light on. If time data is available the light will come on synchronised to every other light with the same selected flash code. Synchronisation is achieved using an internal algorithm based on the highly accurate time base and time data received from the satellites. The satellite data is provided from a number of earth stations using atomic clocks as the time base. Continuous self-checking ensures that the light will continue to run in synchronisation. LIGHT ACTIVATION At power-up the microprocessor checks that the internal GPS module is programmed correctly and is able to provide valid time base and time data. Once outside with a clear view of the sky, valid data should become available within 20 minutes. DAYLIGHT OPERATION During daylight hours the microprocessor is in idle mode to reduce power consumption. Time data continues to be updated once per second. The microprocessor will automatically exit the idle mode as soon as dark conditions are detected. DARK OPERATION When dark conditions are detected the light: • Checks for valid time data and is turned on after a delay based on the current time and the length of the selected flash code; • If valid time data is not detected the light will turn on after approximately 10 seconds. This light will not be synchronised. • If the light turns on unsynchronised it will continually check for valid time data. Once valid data is found the light will automatically synchronise. Note: Lights will not synchronise if different flash codes are selected. GPS POWER DEMAND The GPS synchronisation feature has been designed to function with a very low power demand. Typically the total 24hr current used by the GPS module is 36mAh. This is approximately equivalent to 8 minutes of solar charging. Latest products and information available at www.avlite.com 17 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Optional GSM Monitoring & Control The Avlite obstruction light is available with GSM Cell-Phone Monitoring, enabling operators to remotely monitor the status of their installation. The system can also be configured to send out SMS text messages or e-mail alerts to designated operators should alarm conditions be triggered, such as low voltage or light failure. Please contact Avlite for operational information for GSM Monitoring & Control. Latest products and information available at www.avlite.com 18 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Maintenance & Servicing Designed to be maintenance free the Obstruction Lights requires minimal attention, though the following maintenance and servicing information is provided to help ensure the life of your Avlite product. • Occasional cleaning of the dome lens may be required using a cloth and warm soapy water. Trouble Shooting Problem Remedy Light will not activate. • Ensure proper connectivity with power supply • Ensure that the power supply has the right polarity and voltage range • Cover the light sensor to force the light ON Latest products and information available at www.avlite.com 19 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Lantern Status The AV-OL-IMB-12/UM lanterns are fitted with two status LEDs and provide the operator with an indication of the lantern status. There is one red and one yellow status LED. The red status LED is used to indicate the health of the Lantern’s power system. The yellow status LED is used to indicate the operational status of the lantern. These indicator LED’s can be viewed at the base of the lens. Red Status LED Lantern Status Lantern Condition Steady Flat Battery cut off is in effect OFF Battery voltage is less than 10.0V Slow High Voltage ON Battery voltage is above 13.5V Off Optimal Voltage ON Battery Voltage is between 12.5V – 13.5V 1 Quick OK Voltage ON Battery Voltage is between 12.0V – 12.5V 2 Quick Low Voltage ON Battery Voltage is between 11.5V – 12.0V 3 Quick Poor Voltage ON Battery Voltage is between 10.0V – 11.5V 4 Quick Flat Voltage ON Battery voltage is less than 10.0V Once the Flat Battery cutoff condition is in effect, the lantern will not turn back on until it sees day light and the battery voltage is above 12.5V for at least one minute. Yellow Status LED Lantern Status Off Daylight, Standby OFF Lantern is in Daylight and in Dusk till Dawn mode or in Standby Mode Quick Flashing Day to night transition OFF Light is activating and will turn on after detecting 30 seconds of continuous darkness. 2 Quick Flashes Night Operation, Not Synchronized ON Lantern is in Normal operating condition. It is not connected to any GPS synchronisation 1 Quick Flashes every 2s Night Operation, Sync in Progress ON Lantern is ‘re-syncing’ with GPS. The lantern re-sync’s with the GPS every 15 minutes. Slow Flashing Night Operation, Synchronized ON Normal operating condition. Lantern is synchronised to GPS-enabled lanterns 2 Quick flashes Night Operation, Synchronized ON Lantern is a Hard Wire Synchronisation Slave. 0.15s on, 0.15s off every 2s 1.5s on, 1.5s off every 11s Lantern Condition If the lantern is not fitted with GPS Synchronisation Option, then the following conditions are not possible: 1 Quick Flash, and Slow Flashing. The LEDs are located on the side of the lantern. Latest products and information available at www.avlite.com 20 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Certification Certified to: FAA AC NO: 150/5345-43 L-864 FAA Engineering Brief No. 67 Latest products and information available at www.avlite.com 21 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Avlite Light Warranty V1.2 Activating the Warranty Upon purchase, the Avlite Systems warranty must be activated for recognition of future claims. To do this you need to register on-line. Please complete the Online Registration Form at: www.avlite.com Avlite Systems will repair or replace your lantern in the event of electronic failure for a period of up to three years from the date of purchase. Avlite Systems will repair or replace any ancillary or accessory products in the event of failure for a period of up to one year from the date of purchase, as per the terms & conditions below. The unit must be returned to Avlite freight prepaid. Warranty Terms 1. Avlite Systems warrants that any Avlite aviation products fitted with telemetry equipment including but not limited to AIS, GSM, GPS or RF (“Telemetry Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of twelve (12) months from the date of purchase by the original purchaser. 2. Avlite Systems warrants that any rotationally-moulded products (“Roto-Moulded Products”) and accessory products (“Accessory Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of twelve (12) months from the date of purchase by the original purchaser. 3. Avlite Systems warrants that any Avlite aviation products other than the Telemetry Products, RotoMoulded Products and Accessory Products (“Avlite Products”) will be free from defective materials and workmanship under normal and intended use, subject to the conditions hereinafter set forth, for a period of four (4) years from the date of purchase by the original purchaser. 4. Avlite Systems will repair or replace, at Avlite’s sole discretion, any Telemetry Products, RotoMoulded Products, Accessory Products or Avlite Products found to be defective in material and workmanship in the relevant warranty period so long as the Warranty Conditions (set out below) are satisfied. 5. If any Telemetry Products or Avlite Products are fitted with a rechargeable battery, Avlite Systems warrants the battery will be free from defect for a period of one (1) year when used within original manufacturer’s specifications and instructions. Warranty Conditions This Warranty is subject to the following conditions and limitations; 1. The warranty is applicable to lanterns manufactured from 1/1/2009. 2. The warranty is void and inapplicable if: a. the product has been used or handled other than in accordance with the instructions in the owner’s manual and any other information or instructions provided to the customer by Avlite; b. the product has been deliberately abused, or misused, damaged by accident or neglect or in being transported; or c. the defect is due to the product being repaired or tampered with by anyone other than Avlite or authorised Avlite repair personnel. 3. The customer must give Avlite Systems notice of any defect with the product within 30 days of the customer becoming aware of the defect. 4. Rechargeable batteries have a limited number of charge cycles and may eventually need to be replaced. Typical battery replacement period is 3-4 years. Long term exposure to high temperatures will shorten the battery life. Batteries used or stored in a manner inconsistent with the manufacturer’s specifications and instructions shall not be covered by this warranty. 5. No modifications to the original specifications determined by Avlite shall be made without written approval of Avlite Systems. 6. Avlite lights can be fitted with 3rd party power supplies and accessories but are covered by the 3rd Latest products and information available at www.avlite.com 22 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models party warranty terms and conditions. 7. The product must be packed and returned to Avlite Systems by the customer at his or her sole expense. Avlite Systems will pay return freight of its choice. A returned product must be accompanied by a written description of the defect and a photocopy of the original purchase receipt. This receipt must clearly list model and serial number, the date of purchase, the name and address of the purchaser and authorised dealer and the price paid by the purchaser. On receipt of the product, Avlite Systems will assess the product and advise the customer as to whether the claimed defect is covered by this warranty. 8. Avlite Systems reserves the right to modify the design of any product without obligation to purchasers of previously manufactured products and to change the prices or specifications of any product without notice or obligation to any person. 9. Input voltage shall not exceed those recommended for the product. 10. Warranty does not cover damage caused by the incorrect replacement of battery in solar lantern models. 11. This warranty does not cover any damage or defect caused to any product as a result of water flooding or any other acts of nature. 12. There are no representations or warranties of any kind by Avlite or any other person who is an agent, employee, or other representative or affiliate of Avlite, express or implied, with respect to condition of performance of any product, their merchantability, or fitness for a particular purpose, or with respect to any other matter relating to any products. Limitation of Liability To the extent permitted by acts and regulations applicable in the country of manufacture, the liability of Avlite Systems under this Warranty will be, at the option of Avlite Systems, limited to either the replacement or repair of any defective product covered by this Warranty. Avlite Systems will not be liable to Buyer for consequential damages resulting from any defect or deficiencies in accepted items. Limited to Original Purchaser This Warranty is for the sole benefit of the original purchaser of the covered product and shall not extend to any subsequent purchaser of the product. Miscellaneous Apart from the specific warranties provided under this warranty, all other express or implied warranties relating to the above product is hereby excluded to the fullest extent allowable under law. The warranty does not extend to any lost profits, loss of good will or any indirect, incidental or consequential costs or damages or losses incurred by the purchaser as a result of any defect with the covered product. Warrantor Avlite Systems has authorised distribution in many countries of the world. In each country, the authorised importing distributor has accepted the responsibility for warranty of products sold by distributor. Warranty service should normally be obtained from the importing distributor from whom you purchased your product. In the event of service required beyond the capability of the importer, Avlite Systems will fulfil the conditions of the warranty. Such product must be returned at the owner’s expense to the Avlite Systems factory, together with a photocopy of the bill of sale for that product, a detailed description of the problem, and any information necessary for return shipment. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. Sealite products are subject to certain Australian and worldwide patent applications. Latest products and information available at www.avlite.com 23 FAA L-864 Medium Intensity Obstruction Light Universal AC & Universal DC Models Other Avlite Products Available Solar Aviation Lighting Helipad Lighting Obstruction Lighting Airfield Markers & Accessories Typical Applications • Temporary & permanent airfield lighting • Remote, emergency & defence airfield lighting • Barricade, hazard & perimeter lighting • Helipad lighting • Obstruction lighting Portable Airfield Lighting System For a complete list of product compliances including ICAO & FAA, please contact Avlite today Head Office Avlite Systems 11 Industrial Drive Somerville, Vic 3912 Australia Tel: +61 (0)3 5977 6128 Fax: +61 (0)3 5977 6124 Email: [email protected] Internet: www.avlite.com A subsidiary of Sealite Pty Ltd www.sealite.com Latest products and information available at www.avlite.com 24 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- FAA L-864 certified
- Medium Intensity LED obstruction lights
- Universal DC & Universal AC models
- Internal diagnostic checking
- Alarm contact for remote monitoring
- Optional IR remote control
- Optional GPS Synchronisation
- Optional GSM Monitoring & Control
- Up to 12 years product life Expectancy
Frequently asked questions
The AV-OL-FL864-12-R model operates on a 12-48 VDC power supply.
The AV-OL-FL864-UM-R model operates on a 110-240VAC power supply.
Both models have a product life expectancy of up to 12 years.
Red is standard. Other colors are available on request.
Options available include: variety of solar/battery configurations, GSM Cell-Phone Monitoring, GPS Synchronisation, RS422/485 communications port.