MONOGRAM ZIC360NPLH 36″ BUILT-IN BOTTOM-FREEZER REFRIGERATOR Installation Guide

Add to My manuals
17 Pages

advertisement

MONOGRAM ZIC360NPLH 36″ BUILT-IN BOTTOM-FREEZER REFRIGERATOR Installation Guide | Manualzz

MONOGRAM 36" BUILT-IN

BOTTOM-FREEZER REFRIGERATOR

ZIC360NPLH

FLUSH INSET INSTALLATION

Allows the refrigerator to be installed flush with adjacent cabinetry

CUSTOM APPEARANCE

Allows personalization with cabinet-compatible panels and custom handles

UPFRONT ELECTRONIC CONTROLS

WITH DIGITAL READOUT

Allows precise temperature settings and are positioned for maximum ease of use

HUMIDITY CONTROLLED VEGETABLE

COMPARTMENTS AND SEALED SNACK PANS

Help maintain freshness and help preserve foods longer

ADJUSTABLE, SPILL PROOF GLASS SHELVES

Make it easy to customize storage to handle foods and containers of various sizes

2 SEALED DELI PANS WITH FULL

EXTENSION SLIDES

SIX ADJUSTABLE DOOR BINS

Offer added storage flexibility

GE WATER™ FILTRATION SYSTEM

Delivers clean, great tasting ice

For questions about your appliance, please call 1-800-626-2000.

PAGE 1 OF 17 Product Specification Revised 8/21

SECTION 1

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

SECTION 2

FLUSH INSET INSTALLATION

REQUIRES ADDITIONAL TRIM KIT ZKFN

For questions about your appliance, please call 1-800-626-2000.

PAGE 2 OF 17 Product Specification Revised 8/21

OVERALL DIMENSIONS STANDARD INSTALLATION

36"

(91.5)

25 1/4"

(64.1)

23 5/8"

(60.0)

* 84"

(213.4)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

Shipping Weight

36" (91.4 cm)

84" (213.4 cm)

25 1/4" (64.1 cm)

36 1/2" (92.7 cm)

35 1/2" (90.2cm)

83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

24" (61 cm)

1/4" OD copper tubing or

GE SmartConnect kit

640 lb (290 kg)

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

For questions about your appliance, please call 1-800-626-2000.

FRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

35"

(88.9)

Case width

** Allow

25"

door swing

(63.5) min

clearance for 130˚

SIDE VIEW

TOP VIEW

** 4 9/16"

(11.6) min

clearance to a wall

for 90˚ door swing

** Dimensions based on custom handle height of 2 9/16" (6.5) .

ZIC360NXLH

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

PAGE 3 OF 17 Product Specification Revised 8/21

STANDARD INSTALLATION

24"

(61)

7/16"

(1.1)

Trim overlap

TOP VIEW

35 1/2"

(90.2)

A

ELEC.

*84 +- .500

(212.1-214.6)

*Trim will overlap additional 7/16"

B

ANTI-TIP BRACKET

W

SIDE VIEW FRONT VIEW

Use two additional hole locations at end of brackets

81 1/2"

(207.0)

STANDARD INSTALLATION

ZIC360NHLH_RH

Bracket mounted into vertical wall studs centered within the cutout

Ensure holes selected are centered on the studs

Wall

Studs

75"

From floor to bottom of electrical area

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

STANDARD INSTALLATION

HELPFUL TIPS

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.

• In installation opening, measure

81-1/2" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.

For questions about your appliance, please call 1-800-626-2000.

PAGE 4 OF 17 Product Specification Revised 8/21

ZIC360NXRH

STANDARD 1/4" FRAMED PANEL DIMENSIONS

SINGLE INSTALLATION

A

Grille Panel B

PANEL ASSEMBLY CROSS SECTION

Door

Trim

Optional ZKLN kit handle

1/4" Framed Panel

Fresh

Food

Panel

C

Freezer Drawer Panel D

PANEL DIMENSIONS

1/4" Framed Panel

A B C D

33 7/8" 8 7/8" 46 1/16" 21 7/8"

STANDARD INSTALLATION

HELPFUL TIPS

Trimmed refrigerators are designed to be customized with decorative panels.

Field-installed custom door and grille panels are required.

1/4" FRAMED PANELS:

For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panel – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs.

STANDARD 3/4" OVERLAY PANEL DIMENSIONS

SINGLE INSTALLATION

PANEL ASSEMBLY CROSS SECTION

A

Grille Panel B

Door

3/4" Overlay Panel

Optional ZKLN kit handle

Trim

1/4" Backer Panel

.10" Spacer Panel

Fresh

Food

Panel

C

Freezer Drawer Panel D

PANEL DIMENSIONS

1/4" Backer Panel

A B C D

33 7/8" 8 7/8" 46 1/16" 21 7/8"

.10" Spacer Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"

3/4" Overlay Panel 34 1/8" 9" 46 5/16" 22"

3/4" OVERLAY PANELS:

The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws.

Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panel – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs.

DOOR HANDLES:

Door handle not included. Custom handles supplied by your cabinet maker may be used.

Optional visor handle kit ZKLN available.

For questions about your appliance, please call 1-800-626-2000.

PAGE 5 OF 17 Product Specification Revised 8/21

CUSTOM SIDE PANELS

F

24"

(61.0)

1 7/8"

(4.8)

*3"- 4"

(7.6 - 10.2)

*Depending on installation height

2 9/16"

(6.5)

*84"

*Depending on installation height

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

STANDARD INSTALLATION

HELPFUL TIPS

F Side panels must be used whenever the sides of the refrigerator will be exposed. The

1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips.

Order the side panels from the cabinet manufacturer.

For questions about your appliance, please call 1-800-626-2000.

PAGE 6 OF 17 Product Specification Revised 8/21

DUAL INSTALLATIONS

A

ELEC.

71 1/2"

(181.6)

Finished Width

24 3/16"

(61.4)

ELEC.

*84 +- .500

(212.1-214.6)

Finished Opening

75"

(190.5 )

From floor to bottom of electrical area

24"

(60.9)

Min. Cutout Depth

STANDARD INSTALLATION

HELPFUL TIPS

A A separate 115V, 60Hz,

15- or 20-amp power supply is recommended for each product.

Additional cutout width may be required when side panels are used.

25" min

FRONT VIEW

25" min

STANDARD 1/4" FRAMED PANEL

DIMENSIONS DUAL INSTALLATION

A

130˚

Door swing

B

E

Fresh

Food

Panel

E

Fresh

Food

Panel

C

PANEL ASSEMBLY

CROSS SECTION

Door

Door

Freezer Drawer Panel Freezer Drawer Panel D

10"

(25.4)

WATER

SIDE VIEW

Trim

Trim

PANEL DIMENSIONS

1/4" Framed Panel

A B C D E

69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"

ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH

ZICS360NXLH_ZICS360NXRH

For questions about your appliance, please call 1-800-626-2000.

PAGE 7 OF 17

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed custom door and grille panels are required.

1/4" FRAMED PANELS:

For 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panel – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 25 lbs.

Order ZKBFN720NII unification kit for an integrated appearance on

2 custom panel models installed sideby-side.

Product Specification Revised 8/21

STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION

E

Fresh

Food

Panel

A

PANEL DIMENSIONS

Grille Panel

6"

E

Fresh

Food

Panel

71 1/2"

(181.6)

Finished Width

B

C

24 3/16"

(61.4)

ELEC.

6"

D

(15.2)

1/4"

Backer

Panel

.10"

Spacer

Panel

3/4"

Overlay

Panel

A 69 7/8" 68 1/2" 70 1/8"

B 8 7/8" 7 5/8" 9"

C 46 1/16" 44 11/16" 46 5/16"

D 21 7/8" 20 1/2" (60.9)

Min. Cutout Depth

22"

E 33 7/8" 32 1/2" 34 1/8"

.25" + .10" + .75" = 1.10" Total Panel

Thickness

(212.1-214.6)

PANEL ASSEMBLY

CROSS SECTION Door

3/4" Overlay Panel

Optional ZKLN kit handle

Trim

75"

From floor

.10" Spacer Panel area

DUAL PRODUCT CLEARANCES

23 7/8" min**

To wall

10"

(25.4)

WATER

FRONT VIEW SIDE VIEW

23 7/8" min**

To wall

** Dimensions based on custom

height of 2 9/16” (6.5)

STANDARD INSTALLATION

HELPFUL TIPS

3/4" OVERLAY PANELS:

The decorative panels slide into the trim. The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels. Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE : Left-to-right offset is not always equal to top-to-bottom offset.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panel – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 25 lbs.

Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

DOOR HANDLES:

Door handles not included. Custom handles supplied by your cabinet maker may be used.

Optional visor handle kit ZKLN available.

A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required.

130˚

Door swing

A

130˚

Door swing

For questions about your appliance, please call 1-800-626-2000.

PAGE 8 OF 17

ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH

ZICS360NXLH_ZICS360NXRH

Product Specification Revised 8/21

OVERALL DIMENSIONS

AFTER PANEL INSTALL

38"

(96.5)

FLUSH INSET

INSTALLATION

26" (66.0)

20 5/8"

(52.4)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

38" (96.5 cm)†

84 1/2" (214.6 cm)†

25 15/16" (65.9 cm)†

38 3/4" (98.4 cm)

39" (99.1 cm)

85" (215.9 cm)

26 3/16" (66.5 cm)

1/4" OD copper tubing or

GE SmartConnect kit

Shipping Weight 640 lb (290 kg)

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

For questions about your appliance, please call 1-800-626-2000.

FRONT VIEW

*4"

* Shipping height. Use leveling legs and wheels for maximum 1" height

adjustment from shipping height. Nominal installation height is 84”

SIDE VIEW

35"

(88.9)

Case width

** Allow

15"

door swing

(38.1) min

clearance for 115˚

TOP VIEW

** 4 9/16"

(11.6) min clearance to a wall for 90˚ door swing

** Dimensions based on custom handle height of 2 9/16" (6.5) .

ZIC360NHLH

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

PAGE 9 OF 17 Product Specification Revised 8/21

FLUSH INSET INSTALLATION 3/4" PANELS

FLUSH INSET KIT ZKFN REQUIRED

26 3/16"

(66.5)

Flush inset depth

20 15/16"

(53.2)

Depth to cleat

5 1/4"

(13.3)

TOP VIEW

Case

Finished cleats

Case Trim

Door

3/4" Panel

3/4"

(1.9)

Width of side cleats

39"

(99.1) Flush inset width

37 1/2"

(95.3)

Width between cleats

ELEC.

10"

(25.4)

6"

(15.2)

24 3/16"

(61.4)

1/2"

(1.3)

A

Finished cleats

84"

(213.4) height to cleat

75 1/2"

From floor of electrical area

B

7"

(17.8)

7"

(17.8)

SIDE VIEW

W

FRONT VIEW

ANTI-TIP BRACKET

For questions about your

81 1/2"

(207.0)

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET appliance, please call 1-800-626-2000.

FLUSH INSTALLATION

ZIC360NHLH_RH

Use two additional hole locations at end of brackets

Bracket mounted into vertical wall studs centered within the cutout

Ensure holes selected are centered on the studs

Wall

Studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

PAGE 10 OF 17

FLUSH INSET INSTALLATION

HELPFUL TIPS

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.

• In installation opening, measure 82" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center

32-1/2" of installation opening to ensure

2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.

WARNING:

Door Trim Pinch Point Hazard

Improper installation can lead to a finger pinch point hazard between the side door trim and the cabinets when operating the door, especially with children. To minimize this risk you must follow the installation instructions for cabinet dimensions, trim assembly and door stop angle.

Product Specification Revised 8/21

ZIC360NXRH

FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION

A

Grille Panel

Fresh

Food

Panel

B

C

Freezer Drawer Panel D

PANEL DIMENSIONS

A B C D

38" 10 11/16" 46 9/16" 22 7/16"

3/4" RAISED DOOR PANEL ROUTING

11/32"

1/4"

DETAIL TOP

3/4"

1/4" 7/16"

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

TOP

Back

Back Front

1/4"

DETAIL BOTTOM

LEFT

SIDE

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

2-1/16"

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

For questions about your appliance, please call 1-800-626-2000.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL RIGHT

SIDE

ROUTER DEPTH 1/4"

3/32"

1/4"

2-1/16"

RIGHT

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

PAGE 11 OF 17

FLUSH INSET INSTALLATION

HELPFUL TIPS

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create

“picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

NOTE: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of 4" wide.

DOOR HANDLES

Door handles not included. Custom handles supplied by your cabinet maker may be used.

Order ZKBFN720NII unification kit for an integrated appearance on

2 custom panel models installed side-by-side.

Product Specification Revised 8/21

3/4" RAISED GRILL PANEL ROUTING

DETAIL TOP

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

1-11/16"

Back

TOP

Back Front

3/16"

DETAIL BOTTOM

LEFT

SIDE

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

2-1/16"

Front

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL RIGHT

SIDE

ROUTER DEPTH 1/4"

3/32"

1/4"

2-1/16"

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

RIGHT

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

FLUSH INSET INSTALLATION

HELPFUL TIPS

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or

3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required.

The router depth is 1/4" all the way around the panel’s backs.

Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

NOTE: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of

4" wide.

DOOR HANDLES

Door handles not included. Custom handles supplied by your cabinet maker may be used.

Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

3/4" RAISED DRAWER PANEL ROUTING

11/32"

1/4"

DETAIL TOP

3/4"

1/4" 7/16"

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

Back

TOP

Back Front

1/4"

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL BOTTOM

DETAIL

LEFT SIDE

ROUTER DEPTH 1/4"

2 1/16"

Front

LEFT

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

For questions about your appliance, please call 1-800-626-2000.

DETAIL RIGHT

SIDE

ROUTER DEPTH 1/4"

2 1/16"

RIGHT

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

PAGE 12 OF 17 Product Specification Revised 8/21

FLUSH INSET INSTALLATION 1/2" PANELS

FLUSH INSET KIT ZKFN REQUIRED

26 3/16"

(66.5)

Flush inset depth

20 13/16"

(52.9)

Depth to cleat

5 3/8"

(13.7)

TOP VIEW

Case

Finished cleats

Case Trim

Door

1/2" Panel

3/4"

(1.9)

Width of side cleats

39"

(99.1) Flush inset width

37 1/2"

(95.3)

Width between cleats

ELEC.

10"

(25.4)

24 3/16"

(61.4)

1/2"

(1.3)

A

Finished cleats

85"

(215.9)

84"

(213.4) height to cleat

75 1/2"

From floor to bottom of electrical area

B

7"

(17.8)

7"

(17.8)

SIDE VIEW

W

FRONT VIEW

ANTI-TIP BRACKET

FLUSH INSTALLATION

ZIC360NHLH_RH locations at end of brackets

Bracket mounted into vertical wall studs centered within the cutout

Ensure holes selected are centered on the studs

Wall

Studs

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

For questions about your appliance, please call 1-800-626-2000.

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

PAGE 13 OF 17

FLUSH INSET INSTALLATION

HELPFUL TIPS

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward.

Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the anti-tip system you must use the product installation instructions.

The information below applies to all installation constructions:

• A wall bracket, bolts and toggles will be supplied with the unit.

• The bolts will be used to attach bracket to wall in 4 locations. Two of the locations must penetrate the center of the wall studs.

• The toggles are used for stability in drywall and when metal studs are encountered. Lag bolts are used in wood studs.

• In installation opening, measure

82" from floor and draw a horizontal line.

• Locate and mark the wall studs on horizontal line. Verify at least two studs have their centerlines within the center 32-1/2" of installation opening to ensure 2 wall studs are penetrated.

• The bracket will be centered left to right in opening with bottom of bracket on the horizontal line.

• When unit is placed in opening, the bracket tabs will align with openings in back of the unit. The unit will be secured to the bracket using supplied “L” bolts.

See Installation Instructions for detailed instructions.

Product Specification Revised 8/21

ZIC360NXRH

FLUSH INSET 1/2" PANEL DIMENSIONS

A

Grille Panel B

Fresh

Food

Panel

C

PANEL DIMENSIONS

1/4" Backer Panel

.10" Space Panel

1/2" Overlay Panel

A B C D

33 7/8" 8 7/8" 46 1/16" 21 7/8"

32 1/2" 7 5/8" 44 11/16" 20 1/2"

38" 10 11/16" 46 9/16" 22 7/16"

Freezer Drawer Panel D

FLUSH INSET INSTALLATION

HELPFUL TIPS

The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.

ASSEMBLE THE PANELS WITH

GLUE AND SCREWS:

• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the chart for locating the backer panel to the overlay panel.

Secure the overlay panel to the backer panel with glue and screws.

Screws must be countersunk into the backer panel

Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

NOTE: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of

4" wide.

1/2" OVERLAY PANEL ROUTING DIMENSIONS

C

Hinge Side

Door Panel Back

A

C

Grille Back

D

B

Backer with

Overlay Panel

Assembly

C

Freezer Drawer

A

D

B

A

D

B

Door

Overlay

Panel

1/4"

Backer

Panel

.10"

Spacer

For questions about your appliance, please call 1-800-626-2000.

PANEL DIMENSIONS

Fresh Food Panel

A

2 1/16"

Freezer Panel 2 1/16"

Grille Panel 2 1/16"

B

2 1/16"

2 1/16"

C

5/16"

5/16"

2 1/16" 1 11/16"

D

3/16"

3/16"

3/16"

PAGE 14 OF 17 Product Specification Revised 8/21

3/4" OR 1/2" DUAL INSTALLATIONS

4 5/16"

(10.9)

ELEC.

A

75"

(190.5)

Finished Width

ELEC.

24 3/16"

(61.4)

85"

(215.9)

Finished

Opening

75 1/2"

From floor of electrical area

26 3/16"

(66.5)

Min. Cutout Depth

15"

(38.1) min

FRONT VIEW

15"

(38.1) min

FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION

A

Grille Panel B

Fresh

Food

Panel

E

Fresh

Food

Panel

C

W

SIDE VIEW

Freezer Drawer Panel Freezer Drawer Panel D

PANEL DIMENSIONS

1/4" Backer Panel

.10" Space Panel

1/2" Overlay Panel

A B C D E

69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"

68 1/2"

ZIC360NHLH_ZIC360NHRH

32 1/2"

74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"

For questions about your appliance, please call 1-800-626-2000.

PAGE 15 OF 17

FLUSH INSET INSTALLATION

HELPFUL TIPS

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

A A separate 115V, 60Hz, 15- or 20-amp power supply is recommended for each product.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Unified grille panel – 25 lbs

DOOR HANDLES

Door handles not included. Custom handles supplied by your cabinet maker may be used.

Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

The 1/2" overlay panel must be secured to a .10" spacer panel and a

1/4" thick backer panel, which slides into the trim.

ASSEMBLE THE PANELS WITH

GLUE AND SCREWS:

• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the panels with glue.

• Refer to the chart for locating the backer panel to the overlay panel.

Secure the overlay panel to the backer panel with glue and screws.

Screws must be countersunk into the backer panel

Product Specification Revised 8/21

FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION

A

Grille Panel B

PANEL DIMENSIONS

A B C D E

74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"

Fresh

Food

Panel

E

Fresh

Food

Panel

C

Freezer Drawer Panel Freezer Drawer Panel D

3/4" RAISED DOOR AND DRAWER PANEL ROUTING -

(SEE PAGE 11 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)

11/32"

1/4"

DETAIL TOP

3/4"

1/4" 7/16"

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

TOP

FLUSH INSET INSTALLATION

HELPFUL TIPS

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door, drawer and grille panels are required. For 3/4" raised panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame’ routing allowing the panels to slide into the attached door, drawer and grille trims.

MAXIMUM TOTAL PANEL

WEIGHT:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Unified grille panel – 25 lbs

DOOR HANDLES

Door handles not included. Custom handles supplied by your cabinet maker may be used.

Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

Back

Back Front

3/16"

DETAIL BOTTOM

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL HINGE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

Front

HINGE

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

For questions about your appliance, please call 1-800-626-2000.

3/16"

DETAIL HANDLE

SIDE

HANDLE

SIDE

PAGE 16 OF 17

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Product Specification Revised 8/21

85"

Finished

Opening

ELEC.

75"

(190.5)

Finished Width

24 3/16"

(61.4)

ELEC.

75 1/2"

26 3/16"

(66.5)

Min. Cutout Depth

3/4" OR 1/2" DUAL PRODUCT CLEARANCES

FRONT VIEW

16 7/8"

(42.9) min**

16 7/8"

(42.9) min**

** Dimensions based on custom

handle height of 2 9/16”

W

SIDE VIEW

FLUSH INSET INSTALLATION

HELPFUL TIPS

A In a side-by-side installation of a left-and-right-hand door swing product, 1" clearance between the units is required.

Order ZKBFN720NII unification kit for an integrated appearance on 2 custom panel models installed side-by-side.

115˚

Door swing

115˚

Door swing

A

ZIC360NHLH_ZIC360NHRH

For questions about your appliance, please call 1-800-626-2000.

PAGE 17 OF 17 Product Specification Revised 8/21

advertisement

Key Features

  • Customizable appearance with cabinet-compatible panels and custom handles
  • Adjustable, spill-proof glass shelves for flexible storage
  • Upfront electronic controls with digital readout for precise temperature setting
  • Six adjustable door bins for added storage flexibility
  • GE Water™ Filtration System for clean, great-tasting ice and water
  • Humidity-controlled vegetable compartments and sealed snack pans for maintaining freshness

Related manuals

Frequently Answers and Questions

Does the refrigerator have a water dispenser?
No, the Monogram ZIC360NPLH does not have a water dispenser.
Can I install the refrigerator flush with my cabinets?
Yes, the Monogram ZIC360NPLH can be installed flush with adjacent cabinetry using the optional flush inset installation kit (ZKFN).
What is the capacity of the refrigerator?
The capacity of the Monogram ZIC360NPLH is not specified in the provided document.
Does the refrigerator come with a warranty?
This document does not provide information about the warranty for the Monogram ZIC360NPLH.
What are the dimensions of the refrigerator?
The overall dimensions of the Monogram ZIC360NPLH are 36" (91.4 cm) wide, 84" (213.4 cm) high, and 25 1/4" (64.1 cm) deep.
Download PDF

advertisement