advertisement
Cooking & Holding Oven
M a n u a l C o n t r o l
Model:
500-TH-II
750-TH-II
1000-TH-II
1000-TH-II
750-TH-II
500-TH-II
• INSTALLATION
• OPERATION
• MAINTENANCE
W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800 • 800.558.8744
USA
/
CANADA
FAX: 262.251.7067 • 800.329.8744
U
.
S
.
A
.
ONLY www.alto-shaam.com
p r i n t e d i n u
.
s
.
a
. MN-29455 • 04/11
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Procedures and Precautions . . . . . . . . . . . . . . . . . 2
Installation
Installation Requirements . . . . . . . . . . . . . . . . . . . . . . 3
Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . 3
Dimension Drawings, weights & capacities . . . . . . . . 4-5
Options and Accessories . . . . . . . . . . . . . . . . . . . . . . . 6
Stacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Restraint Requirements - Mobile Equipment . . . . . . . . 8
Drip Tray Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . 10
Operating Instructions
User Safety Information . . . . . . . . . . . . . . . . . . . . . . . 11
Before Initial Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . 12
General Holding Guidelines . . . . . . . . . . . . . . . . . . . . 13
Care and Cleaning
Cleaning and Preventative Maintenance . . . . . . . . . . 14
Protecting Stainless Steel Surfaces . . . . . . . . . . . . . . 14
Cleaning Agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning Materials . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Equipment Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Clean Daily . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Clean the Door Vents . . . . . . . . . . . . . . . . . . . . . . . . 15
Check Overall Condition of Oven . . . . . . . . . . . . . . . . 15
Sanitation
Sanitation/Food Safety . . . . . . . . . . . . . . . . . . . . . . . 16
Internal Food Product Temperatures . . . . . . . . . . . . . 16
Service
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Exterior Service View . . . . . . . . . . . . . . . . . . . . . . . . 18
Exterior Service Parts List . . . . . . . . . . . . . . . . . . . . 19
Electrical Component Service View . . . . . . . . . . . . . . 20
Cable Heating Service Kits . . . . . . . . . . . . . . . . . . . . 20
Electrical Component Parts List . . . . . . . . . . . . . . . . . 21
Wire Diagrams
500-TH-II, 120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
500-TH-II, 208-240V, 230V . . . . . . . . . . . . . . . . . . . . 23
750-TH-II, 1000-TH-II, 120V . . . . . . . . . . . . . . . . . . . 24
750-TH-II, 1000-TH-II, 208-240V, 230V . . . . . . . . . . . 25
Warranty
Transportation Damage and Claims . . . . . . Back Cover
Limited Warranty . . . . . . . . . . . . . . . . . . . . . Back Cover
D E L I V E R Y
This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier.
See Transportation Damage and Claims section located in this manual.
This appliance, complete with unattached items and accessories, may have been delivered in one or more packages. Check to ensure that all standard items and options have been received with each model as ordered.
Save all the information and instructions packed with the appliance. Complete and return the warranty card to the factory as soon as possible to ensure prompt service in the event of a warranty parts and labor claim.
This manual must be read and understood by all people using or installing the equipment model. Contact the Alto-Shaam Tech Team Service
Department if you have any questions concerning installation, operation, or maintenance.
NOTE: All claims for warranty must include the full model number and serial number of the unit.
U N P A C K I N G
1. Carefully remove the appliance from the carton or crate.
NOTE: Do not discard the carton and other packaging material until you have inspected the unit for hidden damage and tested it for proper operation.
®
®
2. Read all instructions in this manual carefully before initiating the installation of this appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the appliance and is to be provided to the owner or manager of the business or to the person responsible for training operators. Additional manuals are available from the Alto-Shaam
Tech Team Service Department.
3. Remove all protective plastic film, packaging materials, and accessories from the appliance before connecting electrical power. Store any accessories in a convenient place for future use.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 1
SAFETY PROCEDURES
AND PRECAUTIONS
Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols may be used throughout this manual.
D A N G E R
Used to indicate the presence of a hazard that WILL cause severe personal injury, death, or substantial property damage if the warning included with this symbol is ignored.
W A R N I N G
Used to indicate the presence of a hazard that CAN cause personal injury, possible death, or major property damage if the warning included with this symbol is ignored.
C A U T I O N
Used to indicate the presence of a hazard that can or will cause minor or moderate personal injury or property damage if the warning included with this symbol is ignored.
C A U T I O N
Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored.
N O T E :
Used to notify personnel of installation, operation, or maintenance information that is important but not hazard related.
1. This appliance is intended to cook, hold or process foods for the purpose of human consumption. No other use for this appliance is authorized or recommended.
2. This appliance is intended for use in commercial establishments where all operators are familiar with the purpose, limitations, and associated hazards of this appliance. Operating instructions and warnings must be read and understood by all operators and users.
3. Any troubleshooting guides, component views, and parts lists included in this manual are for general reference only and are intended for use by qualified technical personnel.
4. This manual should be considered a permanent part of this appliance. This manual and all supplied instructions, diagrams, schematics, parts lists, notices, and labels must remain with the appliance if the item is sold or moved to another location.
N O T E
For equipment delivered for use in any location regulated by the following directive:
DO NOT DISPOSE OF ELECTRICAL
OR ELECTRONIC EQUIPMENT WITH
OTHER MUNICIPAL WASTE.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 2
I N S T A L L A T I O N
D A N G E R
IMPROPER INSTALLATION,
ALTERATION, ADJUSTMENT,
SERVICE, OR MAINTENANCE COULD
RESULT IN SEVERE INJURY, DEATH,
OR CAUSE PROPERTY DAMAGE.
READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.
C A U T I O N
TO PREVENT PERSONAL INJURY,
USE CAUTION WHEN MOVING OR
LEVELING THIS APPLIANCE.
C A U T I O N
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN
IN OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
D A N G E R
DO NOT store or use gasoline or other fl ammable vapors or liquids in the vicinity of this or any other appliance.
The Alto-Shaam cook and hold oven must be installed in a location that will permit the oven to function for its intended purpose and to allow adequate clearance for ventilation, proper cleaning, and maintenance access.
®
S I T E I N S T A L L A T I O N
Emissions testing conducted by Underwriters
Laboratories, Inc.
®
was found to be in compliance with the applicable requirements of NFPA96: 2004
Edition, Par. 4.1.1.2. U.L emissions sampling of grease laden vapor resulted in a total of 0.55 milligrams per cubic meter with no visible smoke and is considered representative of all oven models in the line. Based on these results, hood installation and/or outside venting should not be a requirement in most areas. Verify local codes for locations where more restrictive codes are applicable.
1. The oven must be installed on a stable and level surface.
2. DO NOT install this oven in any area where it may be affected by any adverse conditions such as steam, grease, dripping water, high temperatures, etc.
3. DO NOT store or use any flammable liquids or allow flammable vapors in the vicinity of this oven or any other appliance.
4. This appliance must be kept free and clear of any combustible materials.
5. This appliance must be kept free and clear of any obstructions blocking access for maintenance or service.
MINIMUM CLEARANCE REQUIREMENTS
back left side right side top combustible surfaces
3" (76mm)
1" (25mm)
1" (25mm)
2" (51mm)
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 3 non
combustible surfaces
3" (76mm)
1" (25mm)
1" (25mm)
2" (51mm)
S I T E I N S T A L L A T I O N
500-TH-II
I N S T A L L A T I O N
750-TH-II
21" (532mm) 28-9/16" (726mm)
Electrical
Connection
Shown with optional bumper
Pass-Through
Option
Electrical
Connection
Shown with optional bumper
Pass-Through
Option
19-1/8" (486mm)
18-1/8" (460mm)
29" (736mm)
14-1/2"
(367mm)
26-3/4" (678mm)
25-3/4" (653mm)
34" (864mm)
31-1/2" (799mm)
17" (432mm)
WEIGHT
MODEL
500-TH-II
750-TH-II
Electrical
Connection
Pass-Through
Option
16" (406mm)
19" (483mm)
21-7/8"
(556mm)
26-1/2" (672mm)
*31-13/16" (807mm) - with optional 2-1/2" casters
*35-3/16" (894mm) - with optional 5" casters
*33-3/4" (857mm) - with optional 6" legs
NET
100 lb (45 kg) est .
194 lb (264 kg)
Electrical
Connection
Pass-Through
Option
23-5/8" (600mm)
27-1/8" (688mm)
*32-1/2" (826mm) - with optional 2-1/2" casters
*35-1/4" (894mm) - with optional 5" casters
*33-3/4" (857mm) - with optional 6" legs
24-1/8" (612mm)
SHIP
150 lb (68 kg)
264 lb (120 kg)
PRODUCT\PAN CAPACITY ( eacH comparTmenT )
500-TH-II
40 lb (18kg) maximum voluMe MaxiMuM : 30 quarts (38 liters )
750-TH-II
100 lb (45kg) maximum voluMe MaxiMuM
: 75 quarts
(95 liters
)
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 4
S I T E I N S T A L L A T I O N
1000-TH/II
I N S T A L L A T I O N
25-1/16" (636mm)
Electrical
Connection
Shown with optional bumper
23-5/8" (600mm)
22-5/8" (574mm)
34" (864mm)
31-1/2" (799mm)
17" (432mm)
Electrical
Connection
Pass-Through
Option
20-1/2"
(521mm)
23-1/2" (597mm)
26-15/16" (683mm)
*38-5/8" (981mm) - with optional 2-1/2" casters
*42" (1067mm) - with optional 5" casters
*41-7/8" (1063mm) - with optional 6" legs
WEIGHT
MODEL
1000-TH/II
NET
200 lb (91 kg)
SHIP
275 lb (125 kg)
PRODUCT\PAN CAPACITY ( eacH comparTmenT )
120 lb (54kg) maximum voluMe MaxiMuM : 60 quarts (76 liters )
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 5
OPTIONS AND ACCESSORIES
Bumper, Full Perimeter
(
Not available with
2-1/2 (64mm casters
)
Carving Holder, steaMship priMe rib
( cafeteria
) rouNd
Casters - 2 rigid
, 2 swivel w
/ brake
5" (127mm)
3-1/2" (89mm)
2-1/2" (64mm)
Door with Window right left
haNd
haNd
Door Lock with Key
Drip Pan staNdard with draiN 1-7/16" (37mm) staNdard with draiN 1-11/16" (43mm) staNdard with draiN 1-7/8" (48mm) without draiN , 1-7/16" (37mm) without draiN , 1-7/8" (48mm) extra deep , 4" (102mm)
Legs, 6" (152mm), Stemmed ( set of four
)
Pan Grid, Wire - 18" x
26" paN iNsert
Security Panel w/ Key Lock
Shelf, Stainless Steel flat wire
, reach
iN flat wire
, pass
through rib rack
Stacking Hardware
500-TH-II
5011161
HL-2635
4459
5004862 standard
5008022
5010830
5010829
LK-22567
14813
—
—
11898
—
—
5011149
—
5006787
SH-2326
—
—
5004864
I N S T A L L A T I O N
750-TH-II
5010371
HL-2635
4459
5004862 standard
5008022
5010948
5010949
LK-22567
—
14831
—
—
11906
—
5011149
PN-2115
5004750
SH-2324
SH-2327
SH-2743
5004864
1000-TH-II
5009767
HL-2635
4459
5004862 standard
5008022
5010082
5010076
LK-22567
—
—
5005616
—
11906
15929
5011149
PN-2115
5005776
SH-2325
SH-2346
SH-29474
5004864
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 6
I N S T A L L A T I O N
S I T E I N S T A L L A T I O N
STACKING INSTRUCTIONS
1) If the two appliances were shipped together from the factory, the top unit will have the casters already removed. A stacking kit will be included with the shipment.
If casters need to be removed: lay the unit on its back, and remove the set screw on each caster. Pull the casters out of the unit.
2) While appliance is laid on its back, insert one stacking post in each of the four corners of the upper unit. Secure the stacking posts using one screw and two fl at washers that come with the stacking kit.
Note: The fl ange on the stacking posts must face the outside of the unit.
3) Remove the four top mounting screws from the lower unit. Place the upper appliance, which has the stacking posts installed, on top of the bottom unit. Center the top unit from front to back.
Re-install the four screws through the fl ange of the four stacking posts.
TOP
MOUNTING
SCREWS
STACKING
POSTS
CASTER SET SCREW
TOP
MOUNTING
SCREWS
Stacking Configurations
1000-TH-II with 1000-TH-II, 1000-SK-II, 1000-SK/III or 1000-S
500-TH-II with 500-TH-II, 500-TH/III or 500-S
,
750-TH-II with 750-TH-II, 750-TH/III, 750-S, 767-SK or 767-SK/III,
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 7
I N S T A L L A T I O N
S I T E I N S T A L L A T I O N
A number of adjustments are associated with initial installation and start-up. It is important that these adjustments be conducted by a qualified service technician. Installation and start-up adjustments are the responsibility of the dealer or user. These adjustments include but are not limited to thermostat calibration, door adjustment, leveling, electrical hook-up and installation of optional casters or legs.
RESTRAINT REQUIREMENTS
—MOBILE EQUIPMENT
W A R N I N G
RISK OF ELECTRIC SHOCK.
Appliance must be secured to building structure.
LEVELING
Level the oven from side-to-side and front-to-back with the use of a spirit level. For ovens installed with casters, it is important that the installation surface be level due to the probability of frequent oven repositioning.
We recommend checking the level of the oven periodically to make certain the floor has not shifted nor the oven moved.
NOTE: Failure to properly level this oven can cause improper function and will result in the uneven baking with products consisting of semi-liquid batter.
Any appliance that is not furnished with a power supply cord but that includes a set of casters must be installed with a tether. Adequate means must be provided to limit the movement of this appliance without depending on or transmitting stress to the electrical conduit. The following requirements apply:
1. Casters must be a maximum height of 6" (152mm).
2. Two of the casters must be the locking type.
3. Such mobile appliances or appliances on mobile stands must be installed with the use of a flexible connector secured to the building structure.
A mounting connector for a restraining device is located on the upper back flange of the appliance.
A flexible connector is not supplied by nor is it available from the factory.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 8
I N S T A L L A T I O N
S I T E I N S T A L L A T I O N
DRIP TRAY INSTALLATION INSTRUCTIONS
d b c a
Item Description
1 Double-Sided Tape
2
3
4
Drip Tray Holder
Drip Tray
Qty
1
1
8-32 x 1/4” Phil Screw 3
1
1. Poke holes through double-sided tape
2. Remove backing on double-sided tape
3. Put screws c
5. Place drip tray d in drip tray holder b a
.
a .
which is attached to the back of drip tray holder through holes and attach drip tray holder b to unit .
4. Optional - apply a line of food-grade silicone caulk along top edge of drip tray holder b .
b to seal .
D A N G E R
ENSURE POWER SOURCE
MATCHES VOLTAGE STAMPED
ON APPLIANCE NAMEPLATE.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 9
I N S T A L L A T I O N
E L E C T R I C A L C O N N E C T I O N
The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes.
Plug the unit into a properly grounded receptacle
ONLY, positioning the unit so that the plug is easily accessible in case of an emergency. Arcing will occur when connecting or disconnecting the unit unless all controls are in the “ off
” position.
Proper receptacle or outlet configuration or permanent wiring for this unit must be installed by a licensed electrician in accordance with applicable local electrical codes.
750- and 1000-TH-II models at 208-240V are dual rated units with a conversion switch mounted under an access cover on the rear of the oven, near the power cord.
With the voltage conversion switch in the 200-208V
(UPPER) position, the oven will function properly with a source voltage of between 200 and 208.
With the voltage conversion switch in the 220-240V
(LOWER) position, the unit will function properly with a source voltage of between 220 and 240.
NOTE: ALL 208-240V units are shipped from the factory with the voltage conversion switch in the 220-240 position.
All 125V rated units will function properly with a source voltage of between 100 and 125, 60 Hz.
The 125V rated units are provided with a cord and plug [NEMA #5-20P]. Have a licensed electrician install the proper outlet configuration as required for the unit in accordance with applicable, local electrical codes. This will assure a safe and troublefree installation.
For CE approved units: To prevent an electrical shock hazard between the appliance and other appliances or metal parts in close vicinity, an equalization-bonding stud is provided. An equalization bonding lead must be connected to this stud and the other appliances / metal parts to provide sufficient protection against potential difference. The terminal is marked with the following symbol.
NOTE: CE approved appliances must be connected to an electrical circuit that is protected by an external GFCI outlet.
Ensure that the voltage conversion switch position and the available power source match.
ELECTRICAL - 500-TH-II voltage phase cycle
/ hz amps
kW
120 1 60 16 1.9
208-240 ( agcy ) 1 at 208 1 at 240 1
60 12.5 3.0
60 10.6 2.2
60 12.2 2.9
230 1 50 12 2.8
ELECTRICAL - 750-TH-II voltage phase cycle / hz amps kW
120 1 60 14.2 1.7
208-240 ( agcy ) at 208 at 240
1
1
1
230 1
60
60
60
50
14.4 3.0
14.6 3.0
11.2 2.7
10.4 2.4
ELECTRICAL - 1000-TH-II voltage phase cycle
/ hz amps
kW
120
208-240 ( agcy ) 1 at 208 1 at 240 1
230 1
1 60
60
60
60
50
16.0 1.9
14.4 3.0
14.4 3.0
11.1 2.7
10.4 2.4
D A N G E R cord
& plug
NeMa 5-20 p
20a - 125v plug no cord or plug cee 7/7
220-230v plug cord & plug
NeMa 5-20 p
20a - 125v plug no cord or plug cee 7/7
220-230v plug cord
& plug
NeMa 5-20 p
20a - 125v plug no cord or plug cee 7/7
220-230v plug
Wire diagrams are located inside the bonnet of the unit .
To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the current edition of the National Electrical Code ANSI/
NFPA No. 70. In Canada, all electrical connections are to be made in accordance with CSA C22.1, Canadian
Electrical Code Part 1 or local codes.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 10
O P E R A T I N G I N S T R U C T I O N S
U S E R S A F E T Y I N F O R M A T I O N
C A U T I O N
METAL PARTS OF THIS EQUIPMENT
BECOME EXTREMELY HOT WHEN
IN OPERATION. TO AVOID BURNS,
ALWAYS USE HAND PROTECTION
WHEN OPERATING THIS APPLIANCE.
The Alto-Shaam cook and hold oven is intended for use in commercial establishments by qualified operating personnel where all operators are familiar with the purpose, limitations, and associated hazards of this appliance. Operating instructions and warnings must be read and understood by all operators and users.
S T A R T - U P O P E R A T I O N
BEFORE INITIAL USE:
Interior oven surfaces must be heated to remove surface oils and the accompanying odor produced during the first use of the oven.
1. Wipe all wire shelves, side racks and the full oven interior with a clean, damp cloth. Install the oven side racks, oven shelves, and external drip tray. Shelves are installed with the curved edge toward the back of the oven. Insert the drip pan on the interior bottom surface of the oven.
2. Close the oven doors, press the power switch to the on position, and set the thermostat to
300°F (149°C).
3. Allow the oven to cycle for approximately
2 hours or until no odor is detected.
PREHEATING:
Always preheat the oven for a minimum of 20 minutes before cooking product. Follow the operating instructions indicated on the next page of this manual.
D A N G E R
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
D A N G E R
APPLIANCES WITH NO CORD
PROVIDED BY FACTORY MUST
BE EQUIPPED WITH A CORD OF
SUFFICIENT LENGTH TO PERMIT
THE APPLIANCE TO BE MOVED
FOR CLEANING.
ELECTRICAL CONNECTIONS MUST
BE MADE BY A QUALIFIED SERVICE
TECHNICIAN IN ACCORDANCE WITH
APPLICABLE ELECTRICAL CODES.
D A N G E R
LOCK-OUT OR POST
BREAKER PANEL UNTIL
SERVICE WORK HAS
BEEN COMPLETED.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 11
O P E R A T I N G I N S T R U C T I O N S
Control will display 0°F or 0°C.
2.
Set the holding temperature.
• Rotate the hold knob to the desired holding temperature.
The set temperature will appear in the Digital Display
140
.
F and the temperature display button will illuminate.
4. Set timer.
• Press Up or Down arrows when cook knob is set to begin cooking.
• Press Up or Down arrows to adjust the time while cooking.
•
Note:
Hold timer button for 3 seconds
• The holding indicator light will illuminate while in hold mode.
• Holding temperature range:
60° to 205°F (16 to 96°C)
3. Set the cooking temperature.
• Rotate the cook knob to the desired temperature.
The set temperature will appear in the Digital Display 250.F
and the temperature display button will illuminate.
• The cooking indicator light will illuminate while in cook mode.
• Cooking temperature range:
200° to 325°F (94 to 160°C)
• Note: Cooking mode not active unless timer is running.
shows .
5. PREHEAT oven for 30 minutes before loading food.
The heat indicator light will illuminate and will remain lit as long as the oven is calling for heat.
6.
Load the oven with food and adjust cooking timer as needed.
Notes:
• When the oven temperature reaches the set temperature, the heat indicator light will turn off.
• Press and hold the Temperature Display Button for 3 seconds at any time to display the Actual oven temperature 190.F .
Heat
Indicator Light
Digital
Display
Holding
Indicator Light
Cooking
Indicator Light o o
I I
On/Off
Power Switch
Up/Down
Arrow Keys
Time Key
Hold Knob
Temperature
Display Button
Cook Knob
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 12
O P E R A T I N G I N S T R U C T I O N S
General Holding Guideline
Chefs, cooks and other specialized food service personnel employ varied methods of cooking. Proper holding temperatures for a specific food product must be based on the moisture content of the product, product density, volume, and proper serving temperatures. Safe holding temperatures must also be correlated with palatability in determining the length of holding time for a specific product.
Halo Heat maintains the maximum amount of product moisture content without the addition of water, water vapor, or steam. Maintaining maximum natural product moisture preserves the natural flavor of the product and provides a more genuine taste. In addition to product moisture retention, the gentle properties of Halo Heat maintain a consistent temperature throughout the cabinet without the necessity of a heat distribution fan, thereby preventing further moisture loss due to evaporation or dehydration.
When product is removed from a high temperature cooking environment for immediate transfer into equipment with the lower temperature required for hot food holding, condensation can form on the outside of the product and on the inside of plastic containers used in self-service applications.
Allowing the product to release the initial steam and heat produced by high temperature cooking can alleviate this condition. To preserve the safety and quality of freshly cooked foods, however, a maximum of 1 to 2 minutes must be the only time period allowed for the initial heat to be released from the product.
Most Halo Heat Holding Equipment is provided with a thermostat control between 60° and 200°F
(16° to 93°C). If the unit is equipped with vents, close the vents for moist holding and open the vents for crisp holding.
H O L D I N G T E M P E R A T U R E R A N G E
MEAT
BEEF ROAST — Rare
BEEF ROAST — Med/Well Done
BEEF BRISKET
CORN BEEF
PASTRAMI
PRIME RIB — Rare
STEAKS — Broiled/Fried
RIBS — Beef or Pork
VEAL
HAM
PORK
LAMB
POULTRY
CHICKEN — Fried/Baked
DUCK
TURKEY
GENERAL
FISH/SEAFOOD
FISH — Baked/Fried
LOBSTER
SHRIMP — Fried
BAKED GOODS
BREADS/ROLLS
FAHRENHEIT
130°F
155°F
160° — 175°F
160° — 175°F
160° — 175°F
130°F
140° — 160°F
160°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
120° — 140°F 49° — 60°C
MISCELLANEOUS
CASSEROLES
DOUGH — Proofing
EGGS —Fried
FROZEN ENTREES
HORS D'OEUVRES
PASTA
PIZZA
POTATOES
PLATED MEALS
SAUCES
SOUP
VEGETABLES
160° — 175°F
80° — 100°F
150° — 160°F
160° — 175°F
160° — 180°F
160° — 180°F
160° — 180°F
180°F
140° — 165°F
140° — 200°F
140° — 200°F
160° — 175°F
71° — 79°C
27° — 38°C
66° — 71°C
71° — 79°C
71° — 82°C
71° — 82°C
71° — 82°C
82°C
60°— 74°C
60° — 93°C
60° — 93°C
71° — 79°C
THE HOLDING TEMPERATURES LISTED ARE SUGGESTED GUIDELINES ONLY
.
ALL
FOOD HOLDING SHOULD BE BASED ON INTERNAL PRODUCT TEMPERATURES
.
ALWAYS FOLLOW LOCAL HEALTH
(
HYGIENE
)
REGULATIONS FOR ALL INTERNAL
TEMPERATURE REQUIREMENTS
.
CELSIUS
54°C
68°C
71° — 79°C
71° — 79°C
71° — 79°C
54°C
60° — 71°C
71°C
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 13
C A R E A N D C L E A N I N G
C L E A N I N G A N D P R E V E N T I V E M A I N T E N A N C E
PROTECTING STAINLESS STEEL SURFACES
It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, or inappropriate chemicals can completely destroy the protective surface layer of stainless steel. Abrasive pads, steel wool, or metal implements will abrade surfaces causing damage to this protective coating and will eventually result in areas of corrosion.
Even water, particularly hard water that contains high to moderate concentrations of chloride, will cause oxidation and pitting that result in rust and corrosion. In addition, many acidic foods spilled and left to remain on metal surfaces are contributing factors that will corrode surfaces.
Proper cleaning agents, materials, and methods are vital to maintaining the appearance and life of this appliance. Spilled foods should be removed and the area wiped as soon as possible but at the very least, a minimum of once a day.
Always thoroughly rinse surfaces after using a cleaning agent and wipe standing water as quickly as possible after rinsing.
CLEANING AGENTS
Use non-abrasive cleaning products designed for use on stainless steel surfaces. Cleaning agents must be chloride-free compounds and must not contain quaternary salts. Never use hydrochloric acid (muriatic acid) on stainless steel surfaces.
Always use the proper cleaning agent at the manufacturer's recommended strength.
Contact your local cleaning supplier for product recommendations.
CLEANING MATERIALS
The cleaning function can usually be accomplished with the proper cleaning agent and a soft, clean cloth. When more aggressive methods must be employed, use a non-abrasive scouring pad on difficult areas and make certain to scrub with the visible grain of surface metal to avoid surface scratches. Never use wire brushes, metal scouring pads, or scrapers to remove food residue.
C A U T I O N
N
O
SCRAPER
S
N
O
W
IRE
BRUS
H
E
S
N
O
ST
EEL PA
D
S
TO PROTECT STAINLESS STEEL
SURFACES, COMPLETELY AVOID
THE USE OF ABRASIVE CLEANING
COMPOUNDS, CHLORIDE BASED
CLEANERS, OR CLEANERS
CONTAINING QUATERNARY SALTS.
NEVER USE HYDROCHLORIC ACID
(MURIATIC ACID) ON STAINLESS
STEEL. NEVER USE WIRE
BRUSHES, METAL SCOURING
PADS OR SCRAPERS.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 14
C A R E A N D C L E A N I N G
EQUIPMENT CARE
Under normal circumstances, this oven should provide you with long and trouble free service. There is no preventative maintenance required, however, the following Equipment
Care Guide will maximize the potential life and trouble free operation of this oven.
The cleanliness and appearance of this equipment will contribute considerably to operating efficiency and savory, appetizing food. Good equipment that is kept clean works better and lasts longer.
CLEAN DAILY
1. Disconnect unit from power source, and let cool.
2. Remove all detachable items such as wire shelves, side racks, and drip pans. Clean these items separately.
3. Wipe the interior metal surfaces of the oven with a paper towel to remove loose food debris.
4. Clean the interior metal surfaces of the cabinet with a damp clean cloth or sponge and any good commercial detergent.
NOTE: Avoid the use of abrasive cleaning compounds, chloride based cleaners, or cleaners containing quaternary salts. Never use hydrochloric acid
(muriatic acid) on stainless steel.
5. Spray heavily soiled areas with a water soluble degreaser and let stand for 10 minutes, then remove soil with a plastic scouring pad.
6. Wipe control panel, door vents, door handles, and door gaskets thoroughly since these areas harbor food debris.
7. Rinse surfaces by wiping with sponge and clean warm water.
8. Remove excess water with sponge and wipe dry with a clean cloth or air dry. Leave doors open until interior is completely dry. Replace side racks and shelves.
9. Wipe door gaskets and control panel dry with a clean, soft cloth.
10. Interior can be wiped with a sanitizing solution after cleaning and rinsing. This solution must be approved for use on stainless steel food contact surfaces.
11. To help maintain the protective film coating on polished stainless steel, clean the exterior of the cabinet with a cleaner recommended for stainless steel surfaces. Spray the cleaning agent on a clean cloth and wipe with the grain of the stainless steel.
12. Clean any glass with a window cleaner.
Always follow appropriate state or local health
(hygiene) regulations regarding all applicable cleaning and sanitation requirements for equipment.
CLEAN THE DOOR VENTS
Door vents need to be inspected and cleaned as required.
CHECK OVERALL CONDITION OF
OVEN ONCE A MONTH
Check the oven once a month for physical damage and loose screws. Correct any problems before they begin to interfere with the operation of the oven.
DO NOT USE OVEN IF CONTROLS ARE NOT
PROPERLY FUNCTIONING
Refer to the Trouble Shooting Guide located in this manual or call an authorized service technician.
D A N G E R
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
D A N G E R
AT NO TIME SHOULD THE INTERIOR
OR EXTERIOR BE STEAM CLEANED,
HOSED DOWN, OR FLOODED WITH
WATER OR LIQUID SOLUTION OF
ANY KIND. DO NOT USE WATER JET
TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 15
S A N I T A T I O N
Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor. Cleanliness, top operating efficiency, and appearance of equipment contribute considerably to savory, appetizing foods.
Good equipment that is kept clean, works better and lasts longer.
The most accurate method of measuring safe temperatures of both hot and cold foods is by internal product temperature. A quality thermometer is an effective tool for this purpose, and should be routinely used on all products that require holding at a specific temperature.
Most food imparts its own particular aroma and many foods also absorb existing odors.
Unfortunately, during this absorption there is no distinction between GOOD and BAD odors.
The majority of objectionable flavors and odors troubling food service operations are caused by bacteria growth. Sourness, rancidity, mustiness, stale or other OFF flavors are usually the result of germ activity.
The easiest way to insure full, natural food flavor is through comprehensive cleanliness. This means good control of both visible soil (dirt) and invisible soil (germs). A thorough approach to sanitation will provide essential cleanliness. It will assure an attractive appearance of equipment, along with maximum efficiency and utility. More importantly, a good sanitation program provides one of the key elements in the prevention of food-borne illnesses.
A controlled holding environment for prepared foods is just one of the important factors involved in the prevention of food-borne illnesses.
Temperature monitoring and control during receiving, storage, preparation, and the service of foods are of equal importance.
A comprehensive sanitation program should focus on the training of staff in basic sanitation procedures. This includes personal hygiene, proper handling of raw foods, cooking to a safe internal product temperature, and the routine monitoring of internal temperatures from receiving through service.
Most food-borne illnesses can be prevented through proper temperature control and a comprehensive program of sanitation. Both these factors are important to build quality service as the foundation of customer satisfaction. Safe food handling practices to prevent food-borne illness is of critical importance to the health and safety of your customers.
HACCP, an acronym for Hazard Analysis (at)
Critical Control Points, is a quality control program of operating procedures to assure food integrity, quality, and safety. Taking steps necessary to augment food safety practices is both cost effective and relatively simple. While HACCP guidelines go far beyond the scope of this manual, additional information is available by contacting:
CENTER FOR FOOD SAFETY AND APPLIED
NUTRITION FOOD AND DRUG ADMINISTRATION
1-888-SAFEFOOD
INTERNAL FOOD PRODUCT TEMPERATURES
H OT FOOD S
DANGER ZONE 40° TO 140°F (4° TO 60°C)
CRITICAL ZONE
SAFE ZONE
DANGER ZONE
SAFE ZONE
DANGER ZONE
CRITICAL ZONE
SAFE ZONE
70° TO 120°F
140° TO 165°F
COLD FOOD S
ABOVE 40°F
36° TO 40°F
FROZEN FOOD S
ABOVE 32°F
0° TO 32°F
0°F or below
(21° TO 49°C)
(60° TO 74°C)
(ABOVE 4°C)
(2° TO 4°C)
(ABOVE 0°C)
(-18° TO 0°C)
(-18°C or below)
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 16
S E R V I C E
T R O U B L E S H O O T I N G C H E C K L I S T
Error
Code Description Possible Cause
E-10
E-11
E-20
Product probe is shorted
Oven will cook in time only
E-21
Product probe is open
Oven will cook in time only
E-30 Under temperature
E-31
E-50
E-51
E-60
E-61
E-78
E-79
E-80
E-81
E-82
E-83
E-85
E-86
E-87
Cavity air sensor shorted
Cavity air sensor open
Over temperature
Temp. measurement error
Temp. measurement error
Real time clock error
Real time clock error
Voltage low
Voltage high
EEPROM Error
EEPROM Error
EEPROM Error
EEPROM Error
EEPROM Error
EEPROM Error
EEPROM Error
Cavity air sensor reading < 5°F. Verify sensor integrity.
See sensor test instructions below.
Cavity air sensor reading > 517°F. Verify sensor integrity.
See sensor test instructions below.
Product probe reading < 5°F. Verify sensor integrity.
See sensor test instructions below.
Product Probe reading > 517°F. Verify sensor integrity.
See sensor test instructions below.
Unit has not reached set-point for more than 90 minutes.
Unit has been higher than 25°F above the maximum cavity set-point for more than 2 minutes. Note: Holding Cabinets with this error code are more than 145°F higher than the maximum set-point.
Contact factory.
Contact factory.
Data set to factory default. Ensure that date and time are correct if applicable.
Contact factory.
Voltage below 90 VAC on a 125 VAC unit, or below 190 VAC on a
208-240 VAC unit. Correct voltage.
Voltage over 130 VAC on a 125 VAC unit, or over 250 VAC on a
208-240 VAC unit. Correct voltage.
Ensure that all temperatures and times are properly set.
Contact factory if problem persists.
Contact factory.
Contact factory.
Contact factory.
All timers, if previously on, are now off. Possible bad EEPROM.
Stored HACCP memory corrupted. HACCP Address reset to 1. Possible bad
EEPROM. Contact factory if problem persists.
Stored offsets corrupted. Offsets reset to 0. Control may need a recalibration.
Possible bad EEPROM. Contact factory if problem persists.
E-88
E-90
EEPROM Error
Button stuck
All timer set-points are reset to 1 minute. Timers, if previously on, are now off. Possible bad EEPROM.
A button has been held down for >60 seconds. Adjust control. Error will reset when the problem has been resolved.
E-dS
E-dT
E-dU
Datakey error
Datakey error
Datakey unplugged
Datakey digital signature incompatible. Cycle power, and install compatible
Datakey if error persists.
Datakey incompatible with control. Install compatible Datakey.
Install Datakey and cycle power to control to clear error.
Note: If in doubt, always cycle the power to the control and contact factory if the problem persists.
To test probe and air sensor:
Tes t probe and air sensor by placing sensor in ice water bath and using an ohmmeter set on the ohm scale. The reading should be 100 ohms resistance. If it is more than 2 ohms higher or lower, sensor needs to be replaced .
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 17
S E R V I C E
S E R V I C E V I E W
EXTERIOR VIEW -
750-TH-II SHOWN
A
9
7
13
18
11
28
29
2
10
15
8
7
24
19
22 1
12
16
26
24
20
23 17
4
6
Part numbers and drawings are subject to change without notice .
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 18
S E R V I C E
S E R V I C E V I E W - E X T E R I O R
EXTERIOR PARTS LIST A
ITEM
6
7
4
5*
1
2
3*
10
11
8
9
12
13
14*
15
27
28
29
23
24
25*
26*
19
20
21*
22
16
17
18
* noT sHown
DESCRIPTION
SHIM, HANDLE
DRIP PAN WELD
NON-PRODUCT PROBE SEAL
CASTER SPACER
SENSOR GUARD
BOTTOM PANEL
PANEL, SIDE
BACK PANEL
TOP COVER
INSULATION
DRIP TRAY KIT
- DRIP TRAY HOLDER
- DRIP TRAY
DOOR ASSEMBLY, RH
DOOR ASSEMBLY, LH
BONNET ASSEMBLY, SPOT
BLOCK, CONTROL SENSOR
CORDSET, 120V
CORDSET, 230V
CASTER, 3-1/2" RIGID
CASTER, 3-1/2" SWIVEL W/ BRAKE
GASKET, BONNET
HANDLE, OFFSET MAG . LATCH
HINGE
PROBE, OVEN TEMP .
SCREW, 3/4" PAN HD
SCREW,10-32 X 3/4",NF PHIL
SCREW,10-32X1-1/2",NF, PHIL
SCREW, 6-32 X 1/2", NC PHIL, FLAT
SCREW,1/4-20 X 1/2", NC SLOT RND
SCREW, 8-32 X 1/4" PHIL
SHELF, STAINLESS STEEL
SIDE RACK, CHROME
MODEL > 500-TH-II 750-TH-II 1000-TH-II
2
4
6
10
1
2
1
1
28
3
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
12
1
1
1
1
5010947
5012403
BK-27878
CD-3397
CD-3922
CS-25674
CS-25675
GS-23622
HD-27080
HG-22338
PR-34494
SC-2071
SC-2072
SC-2073
SC-2239
SC-2332
SC-2459
SH-2324
SR-28405
13947
14831
1006871
1007145
1008272
1010394
1010395
1010957
1011671
IN-22364
5010391
1010584
1010585
5010946
PART NO.
QTY PART NO.
QTY PART NO.
QTY
5010829
5012452
BK-27878
CD-3397
CD-3922
CS-25674
CS-25675
GS-23622
HD-27080
HG-22338
PR-34494
SC-2071
SC-2072
SC-2073
SC-2239
SC-2332
SC-2459
SH-2326
SR-28403
13947
14813
1006871
1007145
1008272
1010774
1010799
1010801
1011676
IN-22364
5010736
101782
1010783
5010828
2
4
6
10
1
2
1
1
30
3
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
12
1
1
1
1
5010071
5008982
BK-27878
CD-3397
CD-3922
CS-25674
CS-25675
GS-23622
HD-27080
HG-22338
PR-34494
SC-2071
SC-2072
SC-2073
SC-2239
SC-2332
SC-2459
SH-2325
SR-2266
13947
5005616
1006871
1007145
1008272
1009941
1010575
1010574
1011668
IN-22364
5009716
1010188
1010189
5010081
2
4
6
10
1
2
1
1
30
3
4
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
12
1
1
1
1
D A N G E R
LOCK-OUT OR POST
BREAKER PANEL UNTIL
SERVICE WORK HAS
BEEN COMPLETED.
D A N G E R
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 19
S E R V I C E
ELECTRONIC COMPONENTS
208-240V SHOWN
B
4
10
33
12
17
27
35
21
14
3
11
25
36
1 31
20
29
28
24
23
21
26
32
19
22
15
18
Part numbers and drawings are subject to change without notice .
CABLE HEATING SERVICE KITS
No. 4880
500, 750, 1000-TH-II, 120V
500-TH-II, 208-240V includes:
CB-3045 . . . .Cable Heating Element . . . . 134 feet
CR-3226 . . . .Ring Connector . . . . . . . . . . . . . . . 4
IN-3488 . . . .Insulation Corner . . . . . . . . . . .1 foot
BU-3105 . . . .Shoulder Bushing . . . . . . . . . . . . . . 4
BU-3106 . . . .Cup Bushing . . . . . . . . . . . . . . . . . 4
ST-2439 . . . .Stud . . . . . . . . . . . . . . . . . . . . . . . . 4
NU-2215 . . .Hex Nut . . . . . . . . . . . . . . . . . . . . . 8
SL-3063 . . . .Insulating Sleeve . . . . . . . . . . . . . . 4
TA-3540 . . . .Electrical Tape . . . . . . . . . . . . . 1 roll
No. 4881
750,1000-TH-II, 208-240V includes:
CB-3045 .......Cable Heating Element . . . . 210 feet
CR-3226 .......Ring Connector . . . . . . . . . . . . . . 12
IN-3488 ........Insulation Corner . . . . . . . . . . .1 foot
BU-3105 .......Shoulder Bushing . . . . . . . . . . . . . 12
BU-3106 .......Cup Bushing . . . . . . . . . . . . . . . . 12
ST-2439 ........Stud . . . . . . . . . . . . . . . . . . . . . . . 12
NU-2215 ......Hex Nut . . . . . . . . . . . . . . . . . . . . 24
SL-3063 ........Insulating Sleeve . . . . . . . . . . . . . 12
TA-3540 .......Electrical Tape . . . . . . . . . . . . . 1 roll
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 20
8
7
5
2
31
S E R V I C E
ELECTRONIC COMPONENTS PARTS LIST B
MODEL >
ITEM DESCRIPTION
11
12
13*
9*
10
7
8
5
6*
3
4
1
2
14
15
16*
17
30
31
32
33
26
27
28
29
34
35
21
22
23
24
25
18
19
20
SWITCH COVER
ACCESS COVER
FAN TUNNEL COVER
BONNET SPOT ASSEMBLY
T-BLOCK
BRACKET, TETHER (208-240V ONLY)
1/2" HOLE BUSHING
7/8" SNAP BUSHING
BUSHING, STRAIN RELIEF (120V, 230V)
1 1/8" SNAP BUSHING
CABLE, WIRE HARNESS
CONTROL
CORDSET, 230V
CORDSET, 120V
CONNECTOR
CONNECTOR-5 CONDUCTOR
CONNECTOR #16 FERRUL (230V ONLY)
FAN, 3" BOX, 230V
FAN, 3” BOX, 120V
1/2" SELF ADHESIVE GASKET
KNOB, THERMOSTAT
NUT, 10-32, NF HEX MS, #18-8 S/S
M4-0 .7 HEX NUT 18-8
CONTROL PANEL OVERLAY
PLUG, 3/8" HOLE
PLUG, 13/16" HOLE
10-32 X 1/4" PAN HD GROUND SCREW
SCREWS, M4-0 .7X6MM PHIL
8-32 X 2 SLOT PAN HEAD 18-8 S .S .
6-32 X 1-1/4" ROUND HD
SCREW, 10-32 X 1/2", NF PHIL, FLAT
8-32 X 1/2" PHIL SCR EW
8-32 X 1/4" PHIL SCREW
SWITCH, RKR, 20AMP, 250V
20A, TOGGLE SWITCH
THERMOSTAT, COOK
WASHER, SPLIT LOCK
36
* noT sHown
STAR LOCK WASHER
D A N G E R
LOCK-OUT OR POST
BREAKER PANEL UNTIL
SERVICE WORK HAS
BEEN COMPLETED.
500-TH-II 750-TH-II 1000-TH-II
2
4
2
2
2
2
4
1
1
3
4
1
1
3
1
2
2
1
2
1
1
1
2
7
1
1
1
1
1
8
1
1
1
1
1
1
1
1
CR-34559
CR-34646
CR-34828
FA-34524
FA-3974
GS-2019
KN-26568
NU-2215
NU-22286
PE-29360
PG-25574
PG-3589
SC-2190
SC-22271
SC-23154
SC-2365
SC-23670
11133
1009990
1011565
5012403
BK-3019
BT-26884
BU-3006
BU-3007
BU-3964
BU-3378
CB-34945
CC-34488
CD-3922
CD-3397
SC-2425
SC-2459
SW-34769
SW-3528
TT-34910
WS-22300
WS-2467
PART NO.
QTY PART NO.
QTY PART NO.
QTY
CR-34559
CR-34646
CR-34828
FA-34524
FA-3974
GS-2019
KN-26568
NU-2215
NU-22286
PE-29362
PG-25574
PG-3589
SC-2190
SC-22271
SC-23154
SC-2365
SC-23670
11133
1009990
1011565
5012452
BK-3019
BT-26884
BU-3006
BU-3007
BU-3964
BU-3378
CB-34945
CC-34488
CD-3922
CD-3397
SC-2425
SC-2459
SW-34769
SW-3528
TT-34910
WS-22300
WS-2467
2
4
2
2
2
2
4
1
1
3
4
1
1
3
1
2
2
1
2
1
1
1
2
7
1
1
1
1
1
8
1
1
1
1
1
1
1
1
CR-34559
CR-34646
CR-34828
FA-34524
FA-3974
GS-2019
KN-26568
NU-2215
NU-22286
PE-28685
PG-25574
PG-3589
SC-2190
SC-22271
SC-23154
SC-2365
SC-23670
11133
1009990
1011565
5008982
BK-3019
BT-26884
BU-3006
BU-3007
BU-3964
BU-3378
CB-34945
CC-34488
CD-3922
CD-3397
SC-2425
SC-2459
SW-34769
SW-3528
TT-34910
WS-22300
WS-2467
2
4
2
2
2
2
4
1
1
3
4
1
1
3
1
2
2
1
2
1
1
1
2
7
1
1
1
1
1
8
1
1
1
1
1
1
1
1
D A N G E R
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 21
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 22
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 23
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 24
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 25
TRANSPORTATION DAMAGE and CLAIMS
All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee.
Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in the truck or immediately after it is moved to the receiving area.
Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have made a proper count and inspection of all merchandise received.
3. Note all damage to packages directly on the carrier’s delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on the delivery receipt:
Driver refuses to allow inspection of containers for visible damage.
6. Telephone the carrier’s office immediately upon finding damage, and request an inspection. Mail a written confirmation of the time, date, and the person called.
7. Save any packages and packing material for further inspection by the carrier.
8. Promptly file a written claim with the carrier and attach copies of all supporting paperwork.
We will continue our policy of assisting our customers in collecting claims which have been properly filed and actively pursued.
We cannot, however, file any damage claims for you, assume the responsibility of any claims, or accept deductions in payment for such claims.
LIMITED WARRANTY
Alto-Shaam, Inc. warrants to the original purchaser only that any original part that is found to be defective in material or workmanship will, at
Alto-Shaam's option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
The parts warranty period is as follows:
For the refrigeration compressor on Alto-Shaam Quickchillers ™ , five (5) years from the date of installation.
For the heating element on Halo Heat ® cook/hold ovens, as long as the original purchaser owns the oven.
For all other parts, one (1) year from the date of installation or fifteen (15) months from the shipping date, whichever occurs first.
The labor warranty period is one (1) year from the date of installation or fifteen (15) months from the shipping date, whichever occurs first.
Alto-Shaam will bear normal labor charges performed during standard business hours, excluding overtime, holiday rates or any additional fees.
To be valid, a warranty claim must be asserted during the applicable warranty period. This warranty is not transferable.
THIS WARRANTY DOES NOT APPLY TO:
1. Calibration.
2. Replacement of light bulbs, door gaskets, and/or the replacement of glass due to damage of any kind.
3. Equipment damage caused by accident, shipping, improper installation or alteration.
4. Equipment used under conditions of abuse, misuse, carelessness or abnormal conditions, including but not limited to, equipment subjected to harsh or inappropriate chemicals, including but not limited to, compounds containing chloride or quaternary salts, poor water quality, or equipment with missing or altered serial numbers.
5. Damage incurred as a direct result of poor water quality, inadequate maintenance of steam generators and/or surfaces affected by water quality. Water quality and required maintenance of steam generating equipment is the responsibility of the owner/operator.
6. Damage caused by use of any cleaning agent other than Alto-Shaam's Combitherm chlorine or other harmful chemicals. Use of Alto-Shaam's Combitherm ®
® Cleaner, including but not limited to damage due to
Cleaner on Combitherm ® ovens is highly recommended.
7. Any losses or damage resulting from malfunction, including loss of product or consequential or incidental damages of any kind.
8. Equipment modified in any manner from original model, substitution of parts other than factory authorized parts, removal of any parts including legs, or addition of any parts.
This warranty is exclusive and is in lieu of all other warranties, express or implied, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall Alto-Shaam be liable for loss of use, loss of revenue or profit, or loss of product, or for any indirect, special, incidental, or consequential damages. No person except an officer of Alto-Shaam, Inc. is authorized to modify this warranty or to incur on behalf of Alto-Shaam any other obligation or liability in connection with Alto-Shaam equipment.
Effective 09/10
RECORD THE MODEL AND SERIAL NUMBER OF THE APPLIANCE FOR EASY REFERENCE.
ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER IN ANY CONTACT WITH ALTO-SHAAM REGARDING THIS APPLIANCE.
Model: ______________________________________________ Date Installed: ______________________________________________________
Voltage: ______________________________________________ Purchased From: ___________________________________________
Serial Number: _____________________________________________________________________________________________________________
W 1 6 4 N 9 2 2 1 W a t e r S t r e e t
●
P . O . B o x 4 5 0
●
M e n o m o n e e F a l l s , W i s c o n s i n 5 3 0 5 2 - 0 4 5 0
●
U . S . A .
PHONE: 262.251.3800 • 800.558-8744
USA
/
CANADA
FAX: 262.251.7067 • 800.329.8744
U
.
S
.
A
.
ONLY www.alto-shaam.com
TH-II serIes
•
InsTallaTIon
/ operaTIon
/ servIce manual
- pg
. 26 P R I N T E D I N U .
S .
A .
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Delivery
- 3 Unpacking
- 4 Safety Procedures and Precautions
- 5 Installation Requirements
- 5 Clearance Requirements
- 6 Dimension Drawings, weights & capacities
- 8 Options and Accessories
- 9 Stacking Instructions
- 10 Leveling
- 10 Restraint Requirements - Mobile Equipment
- 11 Drip Tray Installation
- 12 Electrical Specifications
- 13 User Safety Information
- 13 Before Initial Use
- 14 Operating Instructions
- 15 General Holding Guidelines
- 16 Cleaning and Preventative Maintenance
- 16 Protecting Stainless Steel Surfaces
- 16 Cleaning Agents
- 16 Cleaning Materials
- 17 Equipment Care
- 17 Clean Daily
- 17 Clean the Door Vents
- 17 Check Overall Condition of Oven
- 18 Sanitation/Food Safety
- 18 Internal Food Product Temperatures
- 19 Trouble Shooting
- 20 Exterior Service View
- 21 Exterior Service Parts List
- 22 Electrical Component Service View
- 22 Cable Heating Service Kits
- 23 Electrical Component Parts List
- 24 500-TH-II, 120V
- 25 500-TH-II, 208-240V, 230V
- 26 750-TH-II, 1000-TH-II, 120V
- 27 750-TH-II, 1000-TH-II, 208-240V, 230V