QC Series 210 Manual 51-3880

QC Series 210 Manual 51-3880
51-3880, 11/08
QC Series
210 Series
Hydraulic Windrow Sweepers
for Skid Loaders
Sweepster Serial Number____________________
Manual Number: 51-3880
Release Date: November 3, 2008
Serial Number 0733001 and Up
800-456-7100 www.paladinbrands.com Sweepster 2800 N. Zeeb Rd., Dexter, MI 48130 United States of America
51-3880, 11/08
51-3880, 11/08
Table of Contents
Section 1 ... Installation.................................................... 5-13
Section 2 ... Operation and Maintenance...................... 15-23
Section 3 ... Service......................................................... 25-30
Section 4 ... Parts............................................................ 31-43
Section 5 ... Options........................................................ 45-54
Section 6 ... Appendix..................................................... 54-61
51-3880, 11/08
51-3880, 11/08
Installation Manual
QC Series Angle Brooms
Table of Contents
Introduction................................................................ 6
Safety Information.................................................7-13
General Safety Information.....................................7-8
Safety Signs & Labels......................................... 10-11
Product Information Section..................................... 12
Installation/Storage.................................................. 13
51-3880, 11/08
SAFETY SECTION
INTRODUCTION
Introduction
Contacting SWEEPSTER
Importance of this Manual
If you have any questions about information in this manual or
need to order parts, please call, write, fax or e-mail
SWEEPSTER.
Read this manual before attempting to operate
the equipment.
This operator’s manual should be regarded as part of the
sweeper. Suppliers of both new and secondhand sweepers are
advised to keep documentation indicating that this manual was
provided with the sweeper.
The manual contains information regarding installation,
operation and maintenance required for this sweeper and
optional equipment. It also includes detailed parts lists.
Purpose of Sweeper
This sweeper is designed solely for use in construction cleanup,
road maintenance, grounds maintenance and similar
operations. Use in any other way is considered contrary to the
intended use. Compliance with and strict adherence to
operation, service and repair conditions, as specified by the
manufacturer, are also essential elements of the intended use.
SWEEPSTER
2800 North Zeeb Road
Dexter, Michigan 48130
Phone: (734) 996-9116 - (800) 456-7100
FAX: (734) 996-9014
e-mail: [email protected]
For help with installation, operation or maintenance
procedures, contact our Technical Service Department. Direct
product questions and parts orders to our Sales Department.
When ordering parts or accessories, be prepared to give the
following information:
•Sweeper model, serial number and date of
purchase
•Prime mover, make and model
•Part number, description and quantity
This sweeper should be operated, serviced and repaired only
by persons who are familiar with its characteristics and
acquainted with relevant safety procedures.
Terms Used in Manual
Accident prevention regulations, all other generally
recognized safety regulations and all road traffic regulations
must be observed at all times.
Right-hand, left-hand, front and rear are determined from the
operator’s perspective (either the operator’s seat or standing
behind a walk-behind unit), facing forward in the normal
operating position.
Any modifications made to this sweeper may relieve the
manufacturer of liability for any resulting damage or injury.
Prime mover refers to the tractor, truck, loader or tow vehicle
that the sweeper is mounted on or towed by.
Safety Alert Symbol
Optional Equipment
This safety alert symbol indicates important safety messages in this manual. When you see this symbol, be
alert to the possibility of injury. Carefully read the message that
follows and inform other operators.
Installation instructions for optional equipment, if applicable,
appear in the Service Manual Section.
Specifications & Features
Due to continuous product improvement, specifications and
features may change without notice.
Warranty
To validate the warranty for this unit, fill out the warranty card or
warranty pages located at the back of this manual. Then, send
this information to SWEEPSTER.
51-3880, 11/08
Safety Information
Read this manual
Read all safety information in this manual. All
operators must read and understand the entire
contents of this manual before sweeping.
General safety practices are listed on Safety
Information pages and specific safety
information is located throughout this manual.
Hazard Definitions
Four hazard classifications are used in this manual. They are
DANGER - Indicates an imminently hazardous
situation which, if not avoided, will result
in death or serious injury.
WARNING - Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION - Indicates a potentially hazardous
situation which, if not avoided, may result
in minor or moderate injury.
NOTICE -
Used for instructions when machine damage
may be involved.
Operation
CAUTION - A sweeper is a demanding machine.
Only fully trained operators or trainee
operators under the close supervision of
a fully trained person should use this
machine.
Before operating sweeper:
•Learn sweeper and prime mover controls in an off-road
location.
•Be sure that you are in a safe area, away from traffic or
other hazards.
•Check all hardware holding the sweeper to the prime
mover, making sure it is tight.
•Replace any damaged or fatigued hardware with
properly rated fasteners. See Maintenance Section
•Make sure all hydraulic hardware and hydraulic fittings
are tight.
•Replace any damaged or fatigued fittings or hoses.
SAFETY SECTION
GENERAL SAFETY INFORMATION
•Check prime mover tire pressure before sweeping.
•Check tire ratings to be sure they match the prime
mover load. Weigh the sweeper end of the prime
mover, if necessary, to insure proper tire rating.
•Remove from the sweeping area all property that
could be damaged by flying debris.
•Be sure all persons not operating the sweeper are
clear of the sweeper discharge area.
• Always wear proper apparel such as a long-sleeved
shirt buttoned at the cuffs; safety glasses, goggles
or a face shield; ear protection; and a dust mask.
While operating sweeper:
•When operating sweeper, adhere to all government
rules, local laws and other professional guidelines for
your sweeping application.
WARNING - Never raise the sweeper more than a few
feet off the ground. The sweeper can tip
back or the prime mover can tip over
causing death or serious injury,
• Before leaving the operator’s area for any reason, lower
the sweeper to the ground. Stop the prime mover
engine, set the parking brake and remove the key from
the ignition.
• Minimize flying debris - use the slowest rotating speed
that will do the job. See Operation Section: Operating
Tips
• Keep hands, feet, hair and loose clothing away from all
moving parts.
• Leave the brush hood (shield) and all other shields and
safety equipment in place when operating the sweeper
and prime mover.
• Be aware of the extra weight and width a sweeper adds.
Reduce travel speed accordingly. See Product
Information Section: Operating the Sweeper.
• When sweeping on rough terrain, reduce speed to avoid
“bouncing” the sweeper. Loss of steering can result.
• Never sweep toward people, buildings, vehicles or other
objects that can be damaged by flying debris.
• Only operate the sweeper while you are in the operating
position. The safety restraint must be fastened while
you operate the prime mover. Only operate the controls
while the engine is running. Protective glasses must be
worn while you operate the prime mover and while you
operate the sweeper.
• While you operate the sweeper slowly in an open area,
check for proper operation of all controls and all
protective devices. Note any needed repairs during
operation of the sweeper. Report any needed repairs.
51-3880, 11/08
SAFETY SECTION
GENERAL SAFETY INFORMATION
Service & Repair - General
CAUTION - Do not modify the sweeper in any way.
Personal injury could result. If you have
questions, contact your dealer or
SWEEPSTER.
Repair or adjust the sweeper in a safe area, away from
traffic and other hazards.
Before adjusting or servicing - lower the sweeper to the
ground, set parking brake, shut down the prime mover
and remove the key from the ignition.
When working on or around the sweeper, safely secure it
from falling or shifting.
Service & Repair - Hydraulic Safety
Stop the prime mover engine and release hydraulic pressure
before servicing or adjusting sweeper hydraulic systems.
WARNING - Escaping hydraulic fluid can have
enough pressure to penetrate the skin,
causing serious personal injury.
Check lines, tubes and hoses carefully. Do not use your
hand to check for leaks. Use a board or cardboard to check
for leaks. Tighten all connections to the recommended
torque. See Appendix.
Do not bend high pressure lines. Do not strike high pressure
lines, Do not install bent lines, bent tubes, or kinked hoses.
Do not install damaged lines, damaged tubes, or damaged
hoses.
Repair loose lines, loose tubes, and loose hoses. Repair
damaged lines, damaged tubes, and damaged hoses.
Leaks can cause fires. See your SWEEPSTER dealer
for repair or replacement parts.
Replace the parts if any of the following conditions are
present:
•The end fittings are damaged or leaking.
•The outer covering is chafed or cut.
•The reinforcing wire layer is exposed.
•The outer covering is ballooning locally.
•The hose is kinked or crushed.
•The hoses have been pulled or stretched.
Make sure that all clamps, guards, and shields are installed
correctly.
51-3880, 11/08
Notes
10
51-3880, 11/08
SAFETY SECTION
SAFETY SIGNS & LABELS
Safety Signs and Labels
There are several specific safety signs on this sweeper. The
exact location of the hazards and the description of the
hazards are reviewed in this section.
Placement or Replacement of Safety Signs
Instructions
1. Clean the area of application with nonflammable solvent,
and then wash the same area with soap and water.
2. Allow the surface to fully dry.
3. Remove the backing from the safety sign, exposing the
adhesive surface.
4. Apply the safety sign to the position shown in the diagram
above and smooth out any bubbles.
• Keep all safety signs clean and legible.
• Replace all missing, illegible, or damaged safety signs.
• Replacement parts, for parts with safety signs attached,
must also have safety signs attached.
• Safety signs are available, free of charge, from your dealer
or from SWEEPSTER.
7
6
5
4
7
2
3
4
Item
2.
3.
4.
5.
6.
7.
50-0634
50-0643
50-0721
50-0722
50-0724
50-0726
Part Qty
1
2
2
1
1
2
Description
Label, Serial Number
Label, Tie Down Point
Label, Warning, Crush Hazard
Label, Warning, Misuse Hazard
Label, Warning, High Pressure Fluid Hazard
Label, Warning, Flying Objects & Entanglement
51-3880, 11/08
11
SAFETY SECTION
SAFETY SIGNS AND LABELS
Safety Signs and Labels
2.
50-0634
3. 50-0643
4. 6. 50-0721
5.
50-0722
7.
50-0726
50-0724
12
51-3880, 11/08
OPERATION SECTION
PRODUCT SPECIFICATIONS
Product Information
Section
QC Brush Head
Approximate Weight
with SAE J2513
Mounting
Specifications and Model
Views
Maximum Width at 0° Articulation
Maximum Length at 0°
Articulation
Maximum Width at 0°
Articulation
Maximum Length at 0° Articulation
Maximum Length at
Full Articulation
Maximum Width at
Full Articulation
Sweeping Width at 0º
Articulation
Sweeping Width at Full
Articulation
Maximum Width at Full Articulation
Single Motor
Dual Motor
793 lbs
829 lbs
5 Ft
852 lbs
890 lbs
6 Ft
915 lbs
953 lbs
7 Ft
982 lbs
1022 lbs
8 Ft
71 inches with SAE J2513
Mounting
70.5 inches
5 Ft
82.5 inches
6 Ft
94.5 inches
7 Ft
106.5 inches
8 Ft
79.5 inches
5 Ft
82.5 inches
6 Ft
85.5 inches
7 Ft
88.5 inches
8 Ft
72 inches
5 Ft
82 inches
6 Ft
93 inches
7 Ft
103 inches
8 Ft
60 inches
5 Ft
72 inches
6 Ft
84 inches
7 Ft
96 inches
8 Ft
54 inches
5 Ft
64 inches
6 Ft
75 inches
7 Ft
85 inches
8 Ft
Maximum Length at Full Articulation
51-3880, 11/08
13
INSTALLATION SECTION
INSTALLING/REMOVING SWEEPER & STORAGE
Sweeper Installation
(Broom to Prime Mover)
WARNING - Improper attachment of sweeper could
result in injury or death. Do not operate
this machine until you have positive
indication that the attachment is securely
mounted.
1. Position the broom on a level surface.
Removing the Sweeper
WARNING - Serious injury or death may result from
disengaging the sweeper when the
sweeper is in an unstable position or
carrying a load. Place the sweeper in a
stable position before disengaging.
NOTICE - Hoses for the sweepers must be removed before
the quick attach is disengaged. Pulling the
sweeper with the hoses could result in damage
to the prime mover or the sweeper.
2. Enter the prime mover.
3.
Fasten the safety restraints.
1. Lower the broom to the ground.
4.
Start the engine.
5.
Disengage the parking brake.
2. Engage the parking brake and shut down the prime
mover. Be sure to relieve pressure to the auxiliary
hydraulic lines.
6. Align the attachment mechanism with the mounting on the
broom, attach to the prime mover. Follow the attaching
procedure in the prime mover owners manual.
3. Unfasten safety restraints and exit prime mover.
7. Engage the parking brake and shut down the prime
mover. Be sure to relieve pressure to the auxiliary
hydraulic lines.
5. Disconnect the broom hydraulic lines from the prime
mover. Connect quick couplers together to keep clean.
8. Unfasten safety restraints and exit the prime mover.
9. Lock jack stands in stowed position. (if available)
10.
Ensure that the hydraulic quick couplers are clean.
Connect hydraulic lines for the broom to the
prime mover. Twist the collar of the quick couplers
one quarter of a turn in order to secure the hydraulic
connections.
11. While the loader arms are lowered, visually inspect the
attachment mechanism to ensure that it is securely
mounted.
12. Enter prime mover, fasten safety restraints and start the
prime mover.
13. Carefully raise the loader and cycle the rollback/dump
cylinders to check clearances, that limiting stops make
proper contact and verify that all mounting procedures
have been successfully completed. Contact SWEEPSTER
for instructions if the limiting stops do not contact properly.
4. Lock jack stands in lowered position. (if available)
6. Disengage attachment locking mechanism.
(mechanical type)
7. Enter prime mover, fasten safety restraints and start the
prime mover.
8. Disengage attachment mechanism. (hydraulic type)
9. Disengage the parking brake, and back away from the
broom.
Storage
NOTICE -
Do not store the sweeper with weight on the
brush. Weight will deform the bristles,
destroying the sweeping effectiveness. To
avoid this problem, place the sweeper on
blocks or use storage stands.
Do not store polypropylene brushes in direct
sunlight. The material can deteriorate and
crumble before the bristles are worn out.
Keep polypropylene brush material away from
intense heat or flame.
14
51-3880, 11/08
Notes
51-3880, 11/08
Operation and
Maintenance Manual
QC Series Angle Brooms
Table of Contents
Operation..............................................................16-18
Operation .........................................................................16
Leveling Sweeper.........................................................17-18
Maintenance.........................................................19-23
Brush Pattern Adjustment..................................................19
Maintenance Schedule......................................................20
Maintenance Record..........................................................21
Replacing Brush Sections..................................................22
Lubrication Points............................................................. 23
15
16
51-3880, 11/08
OPERATION SECTION
SWEEPING/OPERATING TIPS
Before Each Use
4. Engage the brush and then lower it to the ground.
Perform daily maintenance as indicated in Maintenance
Schedule.
5. Increase prime mover engine rpm to sweeping speed.
Run the prime mover and sweeper at a slow idle. Check for
hydraulic leaks or other problems and make corrections, if
necessary, before using the sweeper. See “Hydraulic
inspection guideline” .
WARNING - Avoid serious injury. Check for large
objects that could harm the operator or
others if thrown by the sweeper. Remove
these items before operating.
During Use
Directing Debris
Carry the sweeper low to the ground so that the operator has
good visibility and stability. Avoid any sudden movements.
Avoid excessive downward pressure on the brush sections to
prevent
excessive wear. A two to four inch wide pattern is sufficient for
most
applications. Ensure that the adjustment bolts are equally
adjusted in order to prevent an uneven wear pattern. To adjust
brush pattern see “Adjusting Brush Pattern”.
Direct debris by angling the brush head in that direction.
Observe wind direction. Sweeping with the wind makes
sweeping more effective and helps keep debris off the
operator.
The terms swing and angle are used interchangeably.
Manual Angle
1. Remove the quick release pin from the swing plate.
2. Position the brush head at the desired angle, aligning
holes in the swing plate and mounting frame.
3. Re-insert the quick release pin.
Hydraulic Angle
1. Start the prime mover.
2. Position the brush head at the desired angle by using
6. Travel forward at 5 mph (8 kph) or less.
NOTICE -
Avoid sweeper damage. Reduce travel speed to
avoid hitting immovable objects.
Operating Tips
NOTICE-
Avoid sweeper damage. Do not ram into piles.
Use an appropriate attachment for this type
of job.
Brush, Engine & Travel Speeds
Vary brush, engine and travel speeds to match sweeping
conditions.
Large Areas
When sweeping a large area, such as a parking lot, make a
path down the middle and sweep to both sides. This reduces the
amount of debris that the sweeper must sweep to one side.
Snow
Fast brush speeds and slow travel speeds are needed to sweep
snow effectively. Start at 3/4 throttle and the lowest gear of the
prime mover. For wet and/or deep snow, increase to almost full
throttle. This helps keep snow from packing up inside the brush
hood.
In deep snow you may need to make multiple passes to get
down to a clean surface.
To keep snow from blowing back onto a swept area, always
sweep so the wind is at your back.
Dirt & Gravel
To keep dust at a minimum, use the optional dust suppression
kit or plan sweeping for days when it is overcast and humid or
after it has rained. Also, sweep so the wind blows at your back.
Low brush speeds and moderate travel speeds work best for
cleaning debris from hard surfaces. Brush speeds that are too
fast tend to raise dust because of the aggressive sweeper
action.
Sweeping
To sweep gravel, use just enough brush speed to “roll” the
gravel, not throw it.
To sweep:
Heavy Debris
1. Manual angle only - Swing the brush head assembly
the direction that you want to direct debris.
Travel slowly - 2-3 mph. (3-5 kph)
2. Start the prime mover at idle and raise the brush.
3. Hydraulic angle only - Swing the brush head assembly
the direction that you want to direct debris.
Sweep a path less than the full width of the sweeper.
Increase engine speed if debris becomes very heavy.
51-3880, 11/08
17
MAINTENANCE SECTION
LEVELING THE SWEEPER
Leveling
Level the sweeper for even brush wear and effective use.
CAUTION - Avoid injury. Before adjusting the sweeper,
always turn off the sweeper and the prime
mover engine and remove the key.
1. Move the sweeper to a flat, paved surface.
2. Lower the brush head assembly so the brush is 2 inches
(51 mm) above the ground.
3.
Engage the parking brake and shut down the prime
mover. Be sure to relieve pressure to the auxiliary
hydraulic lines.
4.
Unfasten safety restraints and exit prime mover.
figure 1
5. Check if the swing assembly is level by using a bubble
level. To make corrections:
Adjust tilt cylinders. If the front of the swing assembly is
high, extend tilt cylinders. If low, retract cylinders.
6.
Position the brush head assembly straight ahead. On
each side, measure from the brush frame to the ground
(figure 1). If measurements are not equal:
Loosen hardware that attaches the swing assembly to
the brush head assembly; lower the high side of the
brush head until both sides are an equal distance above
the ground. Tighten the hardware. (figure 2)
figure 2
18
51-3880, 11/08
MAINTENANCE SECTION
LEVELING THE SWEEPER
High
High
Low
Low
Low
figure 3
High
Low
figure 5
Low
High
High
Low
High
High
figure 4
7. Measure to see if the brush head assembly is level when
angled. First, angle the brush head to the right. Measure
as in step 4. Then, angle the brush head to the left.
Measure again. If measurements are equal, the
sweeper is level. If not, proceed with this step.
Low
Low
High
figure 6
To correct leveling problems shown in:
• figure 3, extend tilt cylinders.
• figure 4, retract tilt cylinders.
• figure 5, loosen hardware that attaches the swing
assembly to the brush head assembly; lower the
left-hand side of the brush head until both sides are an
equal distance above the ground. Tighten the
hardware.
• figure 6, loosen hardware that attaches the swing
assembly to the brush head assembly; lower the righthand side of the brush head until both sides are an
equal distance above the ground. Tighten the
hardware.
51-3880, 11/08
19
MAINTENANCE SECTION
BRUSH PATTERN/SPRING CHAIN/TRANSPORT CHAIN
Setting Brush Pattern
A properly adjusted brush offers the best sweeper
performance. To check the brush pattern:
1. Move the sweeper to a dusty, flat surface.
2. Set the prime mover’s parking brake and leave the engine
running.
3. Start the sweeper at a slow speed: lower it so the bristle
tips touch the ground. Run the sweeper in a stationary
position for 10 seconds.
4.
Swept Area
Raise the sweeper and back away; switch off the engine
and remove the key. The brush pattern left in the dust
should be 2-4 inches (51-102 mm) wide, running the
length of the brush. (Compare the swept area with
figure 7.)
2-4 in.
(51-102 mm)
5. Adjust the brush pattern as necessary according to
instructions found in adjusting the Spring-Chain
Assembly.
Figure 7
Adjusting Spring-Chain Assembly
The transport chain supports the weight of the brush head
assembly during transport between work sites and during
adjustment of the spring-chain assemblies.
The spring-chain assembly allows the brush head to pivot up
and down.
To adjust the brush pattern:
1. Lower the sweeper.
2. Tighten the transport chain and lower the sweeper so the
transport chain supports weight.
3. Move the spring chain forward in the swing assembly
chain holder to lower the brush head or backward in the
holder to raise it.
Tightening Transport Chain
To adjust the transport chain:
1.
Extend tilt cylinders.
2.
Tighten the transport chain.
3.
Retract tilt cylinders.
20
51-3880, 11/08
MAINTENANCE SECTION
MAINTENANCE SCHEDULE
Maintenance Schedule
Procedure
Brush head assembly - Level
Brush pattern - Check (See Pattern Adj. Section)
Cylinders - Retract rods
- Grease threaded and ball ends to
prevent rust
Filter, air, prime mover - Clean
Fittings/hoses, hydraulic - Check for leaks/tighten
Check for damage
Fittings, zerk - Grease. (See lubrication points)
Oil, hydraulic - Check Level
Hardware - Check for tightness
Before
Each Use
After
Each Use
100
Hours
500
Hours
See Prime
Mover
Manual
51-3880, 11/08
21
MAINTENANCE SECTION
MAINTENANCE RECORDS
Maintenance Record
Use this log to record maintenance performed on the sweeper.
Date
Maintenance
Procedure Performed
Performed
By
Comments
22
51-3880, 11/08
MAINTENANCE SECTION
REPLACING BRUSH SECTIONS
Replacing Brush Sections
1. Remove motor mount screws. Retain hardware for
reinstallation. Remove motor mount.
2. Remove bearing mounting plate screws from side. Retain
hardware for reinstallation.
3. Remove core from brush head assembly.
4. Remove one half of bearing mount plate from bearing.
5. Remove retaining plate from core assembly.
6. Remove old sections.
7. Install new sections by doing the following:
a. Slide the first section onto the core with the drive pins
on each side of a tube. Make sure that the drive pins
angle up. (figure 1)
figure 1
b. Install a second section with drive pins rotated 180°
from those on the first section. ( figure 2)
c. Continue installing sections, rotating each section 180°
until the core is full.
8. Reattach the section retainer and bearing mounting plate
with previously removed hardware.
9. Lay core on ground. Lower frame over core.
10. Reattach bearing mounting plate with previously removed
hardware.
11. Reattach motor mount with hardware removed in first step.
figure 2
51-3880, 11/08
23
MAINTENANCE SECTION
LUBRICATION POINTS
Lubrication Points
The following grease fittings should be greased before each
use. See figure for locations.
1. Core bearing (1 fitting - single motor only)
2. Brush Head Pivot (2 fitting)
Not Shown:
Hydraulic Angle Cylinder (1 fitting)
1
2
24
51-3880, 11/08
Notes
51-3880, 11/08
25
Service Manual
QC Series Angle Brooms
Table of Contents
Troubleshooting .................................................26-30
Brush Head........................................................................26
Spring-Chain......................................................................27
Lift & Swing........................................................................27
Hydraulic System...............................................................28
Hydraulic Hose Routing.....................................................29
Wiring Harness..................................................................30
26
51-3880, 11/08
SERVICE SECTION
TROUBLESHOOTING
Brush Head
Problem
Possible Cause
Possible Solution
Brush rotates in wrong direction
Hoses installed incorrectly
Switch hoses at brush head tubes
Brush slows or stops when sweeping
Brush pattern too wide
Adjust brush pattern to 2-4 inches
(51-101mm) wide: see Maintenance:
Adjusting Brush Pattern
Travel speed too fast
Travel no more than 5 mph (8 kph)
while sweeping (2-3 mph
recommended)
Trying to sweep too much
material at once
Make several passes with sweeper
Relief pressure set too low
Set relief pressure to 2000 psi
(138.0 bars)
Filter plugging
Change or clean hydraulic oil filter
Brush head assembly “bounces”
during sweeping
Travel speed too fast and/or
brush speed too slow
Find correct combination of ground
and brush speeds: do not travel at
more than 5 mph (8 kph)
Brush wears into cone shape
Sweeper is not level
Level sweeper before each use: see
Maintenance: Leveling
Tires on prime mover at different Check tire sizes and rating: make
pressures or are different sizes corrections as necessary
Brush wears very quickly
Brush pattern too wide
Adjust brush pattern to 2-4 inches
(51-101mm) wide: see Maintenance:
Setting Brush Pattern
51-3880, 11/08
27
SERVICE SECTION
TROUBLESHOOTING
Spring-Chain Assemblies
Problem
Springs on spring-chain
assemblies stretching
Possible Cause
Possible Solution
Transport chain too loose when
traveling between job sites
Adjust according to Adjustment:
Transport Chain
Travel speeds too fast when
sweeping
Do not travel at speeds over
5 mph (8 kph).
Hydraulic Cylinders - Lift & Swing
Problem
Hydraulic cylinder neither extends
nor retracts
Hydraulic cylinder only extends or
only retracts
Hydraulic cylinder extends or
retracts too quickly
Possible Cause
Possible Solution
Manual valve - Control rods not
connected or are binding
Check control rod linkage; make
sure all parts are connected and
are not binding; fix if necessary
Electric valve - No power from
controls because wires are broken
or disconnected
Reconnect wires if disconnected;
replace wires if broken
Electric valve - No power from
controls because switch is broken
Replace switch
Both types of valves - Hydraulic oil
level too low
Fill tank to 2-3 inches (51-76mm)
from top of tank with ISO VG-46 oil
Both types of valves - Hoses or
fittings loose or disconnected
Tighten hoses and fittings
Both types of valves - Restriction
in hoses
Remove bends in hoses, remove
obstructions inside hoses
Electric valve - Set screw in flow
divider on manifold out of
adjustment
Loosen jam nut and then turn set
screw in until it stops; turn set
screw out 1 1/2 turns; tighten jam
nut
Electric valve - Dirt or debris in
spools
Contact Sweepster Technical
Service
Manual valve - Flow too high
because restrictor fitting missing
from cylinder
Reinstall restrictor fitting on barrel
end of cylinder
Manual valve - Flow too high
even though restrictor fitting is
installed
Contact Sweepster for smaller
orifice fitting
28
51-3880, 11/08
SERVICE SECTION
TROUBLESHOOTING
Hydraulic System
Problem
Possible Cause
Hydraulic system overheats
Hydraulic motor seals leak
Possible Solution
Hydraulic oil level too low
Add hydraulic oil to tank until
it comes to 2 inches (51mm)
from top
Restriction in hoses
Remove bends in hoses;
remove obstructions inside
hoses / Replace Hose
Host pump flow rate exceeds
maximum rate of broom
Contact host manufacturer
for proper flow control method
Back pressure exceeds
1000 psi
Contact Sweepster
Motor is failing
High number of hours on
motor; Contact dealer to
rebuild or replace
Hydraulic Schematic
A
B
P
T
P
Pressure
T
Tank
51-3880, 11/08
29
SERVICE SECTION
MOTOR PORTS
Hydraulic Hose Routings
TANK
PRESSURE
TANK
PRESSURE
PRESSURE
TANK
TANK
PRESSURE
TANK
PRESSURE
Manual Angle: Connect pressure line to female quick
disconnect. Connect return line to male quick disconnect.
Hydraulic Angle: Connect pressure line to female quick
disconnect . Connect return line from brush motor(s) to “P” port
on manifold. Connect “T” port on manifold to male quick
disconnect.
Note:
Quick Disconnect Set-Up
Your broom comes equipped with standard ISO 16028 hydraulic quick disconnects (QD’s). They are factory installed using the
broom female QD as the detended pressure line. If your skid steer loader male QD is not the detended pressure line you will need
to swap the positions of the broom QD’s.
APPLICATION
TO
TO
APPLICATION
FROM
ARNESS
TO
PPLICATION
APPLICATION
TO
IDENTIFICATION
FROM
F
E
B
C
D
A
G
H
F
E
C
D
A
PLUG - A, D, E, GG & BH
H
VIEW "A-A"
IDENTIFICATION
A
A
+
A
A
1.0
D
C
B
1.0
A
TO
APPLICATION
F
G
H
D
C
B
A
H
G
F
E
A
B
C
D
C
B
Qty Description
TO
APPLICATION
Item Part
E
B
C
D
A
F
H
G
1. 07-3152 1 Circuit Breaker
2. 07-0868 1 Switch
3. 07-1824 1 Rubber Boot
CONTROL OUT
A
A
1.0
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
PLUG - A, D, E, G & H
FROM
LAF444 WIRE HARNESS
D
IDENTIFICATION
E
B
C
A
F
H
G
D
FROM
TO
APPLICATION
LAF441 WIRE HARNESS
A
A
1.0
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
PLUG - A, D, E, G & H
BATTERY
+
POSITIVE
A
F
A
E
E
B
C
D
A
F
H
G
PLUG - A, D, E, G & H
C
B
A
A
1.0
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
CONTROL OUT
A,D,E,G,H PLUG
D
A
F
H
E
G
B
A
A
A
A,D,E,G,H PLUG
B
G
H
A,D,E,G,H PLUG
IDENTIFICATION
CONTROL OUT
A
1.0
BATTERY
NEGATIVE-
APPLICATION
C
A,D,E,G,H PLUG
H
D
A
A
F
2
A
F
E
A
E
G
TO
B
B
E
G
CONTROL OUT
IDENTIFICATION
FROM
C
B
A
A,D,E,G,H PLUG
A,D,E,G,H PLUG
H
TO
APPLICATION
BATTERY
NEGATIVE
1.0
BATTERY
+
BATTERY
POSITIVE
NEGATIVE-
TO
POSITIVE
APPLICATION
FROM
B
D
A
CONTROL FOUT
C
H
G
CONTROL OUT
PLUG - A, D, E, G & H
CONTROL OUT
BATTERY
NEGATIVE-
BATTERY
+
POSITIVE
VIEW "A-A"
FROM
LAF441 WIRE HARNESS
IDENTIFICATION
APPLICATION
TO
D
A
CATION
FROM
F
H
E
G
A
TO
APPLICATION
TO
Wiring Harness
LAF441 WIRE HARNESS LAF441 WIRE HARNESS
OM
IRE HARNESS
1 WIRE
HARNESS
APPLICATION
SERVICE SECTION
TROUBLESHOOTING
E
PLUG - A, D, E, G & H
WIRE HARNESS
PLUG - A, D, E, G & H
F444 WIRE HARNESS
VIEW
"A-A"
LAF444 WIRE HARNESS VIEW "A-A"
LAF444 WIRE
HARNESS
BATTERY
TION
E HARNESS
51-3880, 11/08
30
1
3
B
B
B
A
B
A
B
51-3880, 11/08
31
Parts Manual
QC Series Angle Brooms
Table of Contents
Parts Lists......................................................................32-43
Brush Head Frames...........................................................32
Core Assemblies................................................................33
Shaft Assembly..................................................................34
Motor Bucket Assembly.....................................................35
Hydraulics-Dual Motor..................................................36-38
Hydraulics-Single Motor................................................39-40
Brush Head Stand.............................................................41
Brush Frame Labels..........................................................42
Quick Attach.......................................................................43
21059MH-XXXX 5 FT
21059MM-XXXX 5 FT
21060MH-XXXX 5 FT
21060MM-XXXX 5 FT
21061MH-XXXX 5 FT
21061MM-XXXX 5 FT
QC, 32”, Single 18 ci, Hydraulic Angle Broom
QC, 32”, Single 18 ci, Manual Angle Broom
QC, 32”, Single 24 ci, Hydraulic Angle Broom
QC, 32”, Single 24 ci, Manual Angle Broom
QC, 32”, Dual, 18 ci, Hydraulic Angle Broom
QC, 32”, Dual, 18 ci, Manual Angle Broom
21071MH-XXXX 6 FT
21071MM-XXXX 6 FT
21072MH-XXXX 6 FT
21072MM-XXXX 6 FT
21073MH-XXXX 6 FT
21073MM-XXXX 6 FT
QC, 32”, Single 18 ci, Hydraulic Angle Broom
QC, 32”, Single 18 ci, Manual Angle Broom
QC, 32”, Single 24 ci, Hydraulic Angle Broom
QC, 32”, Single 24 ci, Manual Angle Broom
QC, 32”, Dual 18 ci, Hydraulic Angle Broom
QC, 32”, Dual 18 ci, Manual Angle Broom
21083MH-XXXX 7 FT
21083MM-XXXX 7 FT
21084MH-XXXX 7 FT
21084MM-XXXX 7 FT
21085MH-XXXX 7 FT
21085MM-XXXX 7 FT
QC, 32”, Single 18 ci, Hydraulic Angle Broom
QC, 32”, Single 18 ci, Manual Angle Broom
QC, 32”, Single 24 ci, Hydraulic Angle Broom
QC, 32”, Single 24 ci, Manual Angle Broom
QC, 32”, Dual 18 ci, Hydraulic Angle Broom
QC, 32”, Dual 18 ci, Manual Angle Broom
21096MH-XXXX 8 FT
21096MM-XXXX 8 FT
21097MH-XXXX 8 FT
21097MM-XXXX 8 FT
QC, 32”, Single
QC, 32”, Single
QC, 32”, Dual
QC, 32”, Dual
24 ci, Hydraulic Angle Broom
24 ci, Manual Angle Broom
18 ci, Hydraulic Angle Broom
18 ci, Manual Angle Broom
32
51-3880, 11/08
PARTS SECTION
BRUSH HEAD FRAME
Brush Head Frames











Item Part
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Qty Description
07-0249 1
07-2952 18
07-3311 1
07-3617 27
07-3842 4
07-4927 6
07-6056 8
13-10004 2
13-12617 1
13-16417 1
13-13278 1
13-13279 1
13-12857 1
13-13280 1
13-13594 1
13-13047 1
13-13048 1
13-16416 1
13-13281 1
13-13282 1
13-13049 1
13-13283 1
13-13595 1


Chain, 1/4 x 22
Screw, HFH, CL10.9, M6-1 x 20
Link, Quick, 5/16
Nut, Insert, M6 x 1
Ring, Snap
Washer, Fender, CL8.8, M6
Nut, Flange, M10-1.5
Pin, Pivot, Left Arm, QA
Plate, Mounting, Brush Head, Pivot
Weld, Brush Frame, 4 Ft
Weld, Brush Frame, 5 Ft
Weld, Brush Frame, 6 Ft
Weld, Brush Frame, 7 Ft
Weld, Brush Frame, 8 Ft
Weld, Brush Frame, 9 Ft
Sheet, Hood, Side, Left
Sheet, Hood, Side, Right
Sheet, Hood, 4 Ft
Sheet, Hood, 5 Ft
Sheet, Hood, 6 Ft
Sheet, Hood, 7 Ft
Sheet, Hood, 8 Ft
Sheet, Hood, 9 Ft


51-3880, 11/08
33
PARTS SECTION
CORE ASSEMBLIES
Core Assemblies
5
1
3
2
4
Item Part
1.
2.
3.
4.
5.
Qty Description
01-1201 1
01-1085 1
01-0930 1
01-0931 1
01-0933 1
01-1148 1
01-1200 1
01-0272C1
01-0020C1
01-0079C1
01-0080C1
01-0530C 1
07-2952 4
07-3617 4
13-13166 1
13-16418 1
13-13284 1
13-13285 1
13-12899 1
13-13286 1
13-13596 1
Section, Set, 32, 10, Mixed, Convoluted ( 4 Ft )
Section, Set, 32, 10, Mixed, Convoluted ( 5 Ft )
Section, Set, 32, 10, Mixed, Convoluted ( 6 Ft )
Section, Set, 32, 10, Mixed, Convoluted ( 7 Ft )
Section, Set, 32, 10, Mixed, Convoluted ( 8 Ft )
Section, Set, 32, 10, Mixed, Convoluted ( 9 Ft )
Section, Set, 32, Poly, Convoluted ( 4 Ft )
Section, Set, 32, Poly, Convoluted ( 5 Ft )
Section, Set, 32, Poly, Convoluted ( 6 Ft )
Section, Set, 32, Poly, Convoluted ( 7 Ft )
Section, Set, 32, Poly, Convoluted ( 8 Ft )
Section, Set, 32, Poly, Convoluted ( 9 Ft )
Screw, HFH, CL10.9, M6-11 x 20
Nut, Insert, M6 x 1
Plate, Ring, Core, End, QC
Weld, Core, 4 Ft, Hex Drive
Weld, Core, 5 Ft, Hex Drive
Weld, Core, 6 Ft, Hex Drive
Weld, Core, 7 Ft, Hex Drive
Weld, Core, 8 Ft, Hex Drive
Weld, Core, 9 Ft, Hex Drive
34
51-3880, 11/08
PARTS SECTION
SHAFT ASSEMBLY
Shaft Assembly
3
10
4
5
11
4
2
5
1
8
3
Item Part
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Qty Description
07-2495 4
07-3738 1
07-3745 8
07-3747 14
07-3748 10
07-3777 1
07-4514 4
08-0067 1
13-11903 1
13-12941 2
13-12974 1
Screw, HHC, CL8.8, M10-1.5 x 35mm
Washer, Lock, Split, Medium, M8
Washer, Flat, CL8.8, M10
Washer, Lock, Split, Medium, M10
Screw, HHC, CL10.9, M10-1.5 x 25mm
Screw, HHC, CL10.9, M8-1.25 x 20mm
Nut, Hex, CL10, M10-1.5
Bearing, 1 1/4, 4 Bolt
Washer, .34 x 1.8 x 10Ga
Plate, Shaft, Brush Frame, Mounting
Weld, Shaft, Hex Drive
4
7
9
6
51-3880, 11/08
35
PARTS SECTION
MOTOR BUCKET ASSEMBLIES
Motor Bucket Assemblies










Item
Part
Qty Description
1. 03-4682 1 Motor, Hydraulic, White, 17.9 Cu In, with Check Valve, Right (Dual Motor)
03-4634 1 Motor, Hydraulic, White, 17.9 Cu In, with Check Valve, Left (Single or Dual Motor)
03-4425 1 Motor, Hydraulic, White, 24.9 Cu In, with Check Valve, Left (Single Motor)
2. 07-3745 4 Washer, Flat, CL8.8, M10
3. 07-3747 10 Washer, Lock, Split, Medium, M10
4. 07-3748 4 Screw, HHC, CL10.9, M10-1.5 x 25mm
5. 07-3749 6 Screw, HHC, CL10.9, M10-1.5 x 30mm
6. 07-4610 2 Nut, Hex, Lock, CL10.9, M12-1.75
7. 07-6178 2 Screw, Socket Head, M12-1.75 x 35mm
8. 13-12946 1 Weld, Motor Bucket
9. 13-15206 1 Hub, Hex, 2 1/2 x 1 1/4, Tapered Bore x 3.75
10. 13-16225 1 Plate, Receiver, Hex, 2.50
Replacement Parts for 03-4682, 03-4634, and 03-4425 Motors :
03-3081 Seal Kit
07-4657 Key
07-4568 Shaft Nut
03-5543 Shaft Motor

36
51-3880, 11/08
PARTS SECTION
HYDRAULIC ASSEMBLIES
Hydraulic Assemblies - Dual Motor
7
6
3
2
9
5
8
Item Part
Qty
1. 03-1939
2. 03-5160
3. 03-5161
03-5162
03-5163
03-5164
4. 03-5165
03-5166
03-5167
03-5168
5. 07-3740
6. 07-4604
7. 07-4942 8. 07-5287
9. 13-15094
10. RHW8614
11. RHW8616
4
2
2
2
2
2
2
2
2
2
1
4
4
3
1
3
3
Description
Fitting, 10MB-10MF
Tee, 12MF-12MF-12MF, Bulkhead
Hose, .50 x 68, 10FF-12FF45, 3.5K (5 ft)
Hose, .50 x 75, 10FF-12FF45, 3.5K (6 ft)
Hose, .50 x 80, 10FF-12FF45, 3.5K (7 ft)
Hose, .50 x 86, 10FF-12FF45, 3.5K (8 ft)
Hose, .50 x 32, 10FF-12FF, 3.5K (5 ft)
Hose, .50 x 38, 10FF-12FF, 3.5K (6 ft)
Hose, .50 x 44, 10FF-12FF, 3.5K (7 ft)
Hose, .50 x 50, 10FF-12FF, 3.5K (8 ft)
Screw, HHC, CL10.9, M8-1.25 x 30mm
Nut, Hex, Lock, CL10.9, M8-1.25
Washer, Fender, 1 1/2 x 5/16
Screw, HHC, CL10.9, M8-1.25 x 65mm
Bracket, Mounting, Bulkhead Tees
Cover Plate
Hose Cradle
10
11
1
4
51-3880, 11/08
37
PARTS SECTION
HYDRAULIC ASSEMBLIES
Hydraulic Assemblies - Dual Motor
Manual Angle
2
1
7
3
8
5
6
9
4
Item Part Qty
Description
1.
2.
3.
4.
5.
6.
7.
8.
9.
Hose, .63 x 140, 12FF-12MB, 2.75K, HS
Screw, HHC, Gr8, 5/16-18 x 2 1/2
Screw, HHC, CL10.9, M8-1.25 x 30mm
Nut, Hex, Lock, CL10.9, M8-1.25
Washer, Fender, 1 1/2 x 5/16
Weld, Plate
Cover, Plate
Hose, Cradle
Hose, Spring
03-5169
07-1784
07-3740
07-4604
07-4942
RHW8613
RHW8614
RHW8616
RHW8618
2
1
1
1
2
1
1
1
1
5
38
51-3880, 11/08
PARTS SECTION
HYDRAULIC ASSEMBLIES
Hydraulic Assemblies - Dual Motor
Hydraulic Angle
11
20
rn
tu
Re
9
21
12
6
re
su
s
re
7
P
16
19
14
22
4
8d
8c
8
18
13
10
8a
5
2
Item Part
1.
2.
3.
4.
5.
6.
7.
8.
8a
8b
8c
8d
03-2291
03-2352
03-2396
03-4700
03-4887
03-5169
03-5173
03-5215
03-5280
07-7150
07-7151
07-7152
07-7153
07-7134
Qty Description
4
2
1
1
1
1
1
1
1
1
1
1
2
2
Fitting, 6MF-6MB, 6F5OLO-S
Hose, .38 x 32, 6FF-6FF90, 4.75K
Elbow, 90, 10MF-12MB
Elbow, 45, 10MF-12MB
Cylinder, 2.50 x 1.38 x 7.50, 3.5K
Hose, .63 x 140, 12FF-12MB, 2.75K, HS
Hose, .63 x 60, 10FF-12FF, 3.625K
Manifold, Swing, 12 Volt
Manifold, Swing, 24 Volt
Valve, Cartridge, Pressure Comp
Valve, Cartridge, Relief
Valve, Cartridge, Directional
Coil, 12 Volt
Coil, 24 Volt
Replacement Part for 03-4887 Cylinder :
03-4888 Seal Kit
03-5035 Cylinder Rod
3
1
Item Part
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
17
8b
8
16
Qty Description
03-5385
07-0206
07-1784
07-3740
07-4604
07-4622
07-4942
07-7131
13-11248
LAF9441
RHW8613
RHW8614
RHW8616
RHW8618
1
2
1
1
1
2
2
2
2
1
1
1
1
1
Hose, .63 x 80, 10FF-10MB, 3K, HS
Pin, Cotter, Gr2, 3/16 x 2
Screw, HHC, Gr8, 5/16-18 x 2 1/2
Screw, HHC, CL10.9, M8-1.25 x 30mm
Nut, Hex, Lock, CL10.9, M8-1.25
Nut, Hex, Lock, CL10.9, M10-1.5
Washer, Fender, 1 1/2 x 5/16
Screw, HHC, CL10.9, M10-1.5 x 160mm
Bushing, 1 x .406 x 1
Wire, Assembly, 9 ft
Weld, Plate
Cover, Plate
Hose, Cradle
Hose, Spring
51-3880, 11/08
39
PARTS SECTION
HYDRAULIC ASSEMBLIES
Hydraulic Assembly - Single Motor
Manual Angle
5
11
2
1
13
4
6
6
10
8
3
7
12
Item Part
8
7
11
9
Qty Description
1. 03-1939
2. 03-4804
3. 03-5153
4. 03-5154
5. 07-1784
6. 07-3740
7. 07-4604
8. 07-4942
9. 07-5287
10. RHW8613
11. RHW8614
12. RHW8616
13. RHW8618
2
2
2
2
1
3
5
8
2
1
3
3
1
Fitting, 10MB-10MF
Fitting, 10MF-10MF, UN
Hose, .50 x 80, 10FF-12MB, 3.5K, HS
Hose, .50 x 112, 10FF- 10FF, 3.5K
Screw, HHC, 5/16-18 x 2 1/2
Screw, HHC, CL10.9, M8-1.25 x 30mm
Nut, Hex, Lock, CL10.9, M8-1.25
Washer, Fender, 1 1/2 x 5/16
Screw, HHC, CL10.9, M8-1.25 x 65mm
Weld, Plate
Cover, Plate
Hose, Cradle
Hose, Spring
40
51-3880, 11/08
PARTS SECTION
HYDRAULIC ASSEMBLIES
Hydraulic Assembly - Single Motor
Hydraulic Angle
n
tur
Re
Pr
e
ur
s
es
9c
9d
9a
Item
1.
2.
3.
4.
5.
6.
7.
8.
9.
9a
9b
9c
9d
10.
11.
12.
Part
03-1939
03-2291
03-2352
03-2396
03-4700
03-4887
03-5153
03-5154
03-5215
03-5280
07-7150
07-7151
07-7152
07-7153
07-7134
03-5383
07-0206
07-1784
Qty Description
Item
2
4
2
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
13. 07-3740
3 Screw, HHC, CL10.9, M8-1.25 x 30mm
14. 07-4604
5 Nut, Hex, Lock, CL10.9, M8-1.25
15. 07-4622
2 Nut, Hex, Lock, CL10.9, M10-1.5
16. 07-4942
8 Washer, Fender, 1 1/2 x 5/16
17. 07-5287
2 Screw, HHC, CL10.9, M8-1.25 x 65mm
18. 07-7131
2 Screw, HHC, CL10.9, M10-1.5 x 160mm
19. 13-11248 2 Bushing, 1 x .406 x 1
20. LAF9441 1 Wire, Assembly, 9ft
21. RHW8613 1 Weld, Plate
22. RHW8614 3 Cover, Plate
23. RHW9616 3 Hose, Cradle
24. RHW9618 1 Hose, Spring
Replacement Part for 03-4887 Cylinder :
03-4888 Seal Kit
03-5035 Cylinder Rod
Fitting, 10MB-10MF
Fitting, 6MF-6MB, 6F5OLO-S
Hose, .38 x 32, 6FF-6FF90, 4.75K
Elbow, 90, 10MF-12MB
Elbow, 45, 10MF-12MB
Cylinder, 2.50 x 1.38 x 7.50, 3.5K Ball
Hose, .50 x 80, 10FF-12MB, 3.5K, HS
Hose, .50 x 112, 10FF-10FF, 3.5K
Manifold, Swing, 12 Volt
Manifold, Swing, 24 Volt
Valve, Cartridge, Pressure, Comp
Valve, Cartridge, Relief
Valve, Cartridge, Directional
Coil, 12 Volt
Coil, 24 Volt
Hose, .50 x 195, 10FF-12MB, 3K, HS
Pin, Cotter, Gr2, 3/16 x 2
Screw, HHC, Gr8, 5/16-18 x 2 1/2
Part
9b
Qty Description
51-3880, 11/08
41
PARTS SECTION
BRUSH HEAD STANDS
Brush Head Stands




Item Part
1.
2.
3.
4.
Qty Description
07-0260
07-0699
07-4748
13-13226
2
2
2
2
Pin, Clevis, Gr2, 3/8 x 2 3/4
Pin, Cotter, Gr2, 1/8 x 1 1/4
Pin, Lock, 3/8 x 2, Grip, Square, 2.50AL
Weld, Stand, Brush Head
42
51-3880, 11/08
PARTS SECTION
BRUSH HEAD LABELS
Brush Head Labels
7
6
5
1
7
4
2
3
4
Item Part
1.
2.
3.
4.
5.
6.
7.
50-0252
50-0634
50-0643
50-0721
50-0722
50-0724
50-0726
Qty Description
1
1
2
2
1
1
2
Label, Logo, Large, White
Label, Serial Number
Label, Tie Down Point
Label, Warning, Crush Hazard
Label, Warning, Misuse Hazard
Label, Warning, High Pressure Fluid Hazard
Label, Warning, Flying Objects & Entanglement
51-3880, 11/08
43
PARTS SECTION
QUICK ATTACH
Quick Attach












Item Part
1. 07-0119
2. 07-1294
3. 07-1558
4. 07-1872
5. 07-2855
6. 07-3120
7. 07-5294
8. 07-6451
9. 07-6903
10. 11-9080
11.



Qty Description
3 Bolt, Carriage, Gr5, 5/8-11 x 1 3/4
4 Nut, Hex, Gr8, 5/8-11
1 Chain, 1/4, 18 Links
4 Washer, Lock, Split, Medium, 5/8
1 Screw, HHC, Gr8, 5/8-11 x 2 1/2
3 Washer, Flat, Gr8, 5/8
1Link, Quick, 5/16, Wide Jaw
1 Spring, Tension, 325#/in
1 Pin, Quick Release, 1 x 3
1 Weld, Swing, Plate
1 Weld, Frame, Mounting (Contact Sweepster with seial number and model
number of unit for correct part)
12. 13-4657 1 Bushing, 1 x 5/8 x .562
13. 50-0635 1 Label, Plate, Part Number/Date
44
51-3880, 11/08
Notes
51-3880, 11/08
45
Options Section
QC Series Angle Brooms
Table of Contents
Options.................................................................46-53
Hood Kits............................................................46-47
Hydraulic Angle........................................................ 48
Dust Suppression Systems.................................49-50
Sight Indicator Kits................................................... 51
Manual to Hydraulic Conversion Kits..................52-53
46
51-3880, 11/08
OPTION SECTION
HOOD KITS
180° Hood Kits with Drape
Factory Installed
28-9787 5 Ft
28-9788 6 Ft
28-9789 7 Ft
28-9790 8 Ft
28-9797 9 Ft
RETAINER STRAP COMBINATIONS
13-15648-2
5 FT
13-15648-3
6 FT
10
7 FT
2
8 FT
9
3
9 FT
1
6
4
1
1
2
5
2
1
11
*See chart for correct
3
4
8
combination.
7
12
6
Item
1.
2.
3.
4.
5.
6.
Part
Qty Description
07-3522 17
07-3617 8
07-3739 12
07-3739 13
07-3739 14
07-3739
15
07-3739
16
07-4942
9
07-7115
12
07-7115 13
07-7115 14
07-7115 15
07-7115 16
13-15648-2 4
13-15648-2 3
13-15648-2 2
13-15648-2 5
13-15648-2 4
Screw, HFH, CL10.9, M6-1 x 20
Nut, Insert, Hex, M6 x 1
Screw, HHC, CL10.9, M8-1.25 x 25mm (5ft)
Screw, HHC, CL10.9, M8-1.25 x 25mm (6ft)
Screw, HHC, CL10.9, M8-1.25 x 25mm (7ft)
Screw, HHC, CL10.9, M8-1.25 x 25mm (8ft)
Screw, HHC, CL10.9, M8-1.25 x 25mm (9ft)
Washer, Fender, 5/16 x 1
Nut, Insert, M8-1.25 (5ft)
Nut, Insert, M8-1.25 (6ft)
Nut, Insert, M8-1.25 (7ft)
Nut, Insert, M8-1.25 (8ft)
Nut, Insert, M8-1.25 (9ft)
Plate, Retainer, Flap, 2 Ft (5ft)
Plate, Retainer, Flap, 2 Ft (6ft)
Plate, Retainer, Flap, 2 Ft (7ft)
Plate, Retainer, Flap, 2 Ft (8ft)
Plate, Retainer, Flap, 2 Ft (9ft)
6
Item
7.
8.
9.
10.
11.
12.
Part
13-15648-3
13-15648-3
13-15648-3
13-15648-3
13-15648-3
13-16045
13-16046
13-16047-5
13-16047-6
13-16047-7
13-16047-8
13-16047-9
13-16199-5 13-16199-6 13-16199-7 13-16199-8 13-16199-9 13-16200 Qty Description
0
1
2
0
1
1
1
1
1
1
1
1
1
1
1
1
1
4
Plate, Retainer, Flap, 3 Ft (5ft)
Plate, Retainer, Flap, 3 Ft (6ft)
Plate, Retainer, Flap, 3 Ft (7ft)
Plate, Retainer, Flap, 3 Ft (8ft)
Plate, Retainer, Flap, 3 Ft (9ft)
Sheet, Hood, Extension, Side, Left
Sheet, Hood, Extension, Side, Right
Sheet, Hood, Extension, 5 Ft
Sheet, Hood, Extension, 6 Ft
Sheet, Hood, Extension, 7 Ft
Sheet, Hood, Extension, 8 Ft
Sheet, Hood, Extension, 9 FT
Flap, Deflector, 180° Hood 5 Ft
Flap, Deflector, 180° Hood 6 Ft
Flap, Deflector, 180° Hood 7 Ft
Flap, Deflector, 180° Hood 8 Ft
Flap, Deflector, 180° Hood 9 Ft
Plate, Spring, 180°, Hood, Flap
51-3880, 11/08
47
OPTION SECTION
HOOD KITS
Field Installed
28-9722 5 Ft
28-9723 6 Ft
28-9724 7 Ft
28-9725 8 Ft
28-9748 9 Ft
180° Hood Kits
Factory Installed
28-9783 5 Ft
28-9784 6 Ft
28-9785 7 Ft
28-9786 8 Ft
28-9796 9 Ft
2
5
3
1
6
4
5
1
2
6
3
Item Part
Qty
Description
1.
2.
3.
4.
5.
6.
3
15
6
1
1
1
1
1
1
1
Washer, Fender, 5/16 x 1 1/2
Screw, HFH, CL10.9, M6-1 x 20
Nut, Insert, Hex, M6 x 1
Sheet, Hood, Extension, Side, Left
Sheet, Hood, Extension, Side, Right
Sheet, Hood, Extension 5 Ft
Sheet,
4 Hood, Extension 6 Ft
Sheet, Hood, Extension 7 Ft
Sheet, Hood, Extension 8 Ft
Sheet, Hood, Extension 9 Ft
07-4942
07-3522
07-3617
13-16045
13-16046
13-16047-5
13-16047-6
13-16047-7
1
13-16047-8
13-16047-9
48
51-3880, 11/08
OPTION SECTION
HYDRAULIC ANGLE
Hydraulic Angle - Field Installed
11-4297 & 11-4298
3
6
5
1
Item Part
1.
2.
3.
4.
5.
6.
03-2092
03-2155
03-2158
03-2159
03-2345
03-4887
07-0206
2
Qty Description
1
2
2
2
1
1
2
Elbow, 90, 6MF-6MB, 6C50L0-S
Hose, .25 x 72, 6FF-6FF, 3.25K (11-4298)
Hose, .25 x 144, 6FF-6FF, 3.25K (11-4297)
Fitting, 6MF-4MP, 6FL0-S
Fitting, Orifice, .078, Elbow, 90°, HP, 9/16MOR, 3/8MFS
Cylinder, 2.50 x 1.38 x 7.50, 3.5K Ball-Cross Tube
Pin, Cotter, 3/16 x 2
Replacement Part for 03-4887 Cylinder :
03-4888 Seal Kit
03-5035 Cylinder Rod
4
5
21
17
51-3880, 11/08
12
15
49
9
19
2
11
1
OPTIONS SECTION
SPRINKLER SYSTEM
3
20
Dust Suppression System
18
4
14
8
7
Field Installed
28-9919 12 Volt
28-10116 24 Volt
16
10
Direct Nozzle Mount
16
11
Factory Installed
28-10114 12 Volt
28-10115 24 Volt
13
NOTE 1: MOUNT SPRINKLER KIT IN THIS
POSITION WHEN USING 180 DEGREE
HOOD OR DIRT DEFLECTOR OPTION.
5
23
21
17
Replacement Parts for 03-1326 and 03-2558 :
07-6565 Fan Shroud
07-6566 Grommet Set (Qty 4)
07-6567 Motor Base Plate
24
22
6
12
19 15
9
21
19
Replacement Parts for LAF8316 :
07-7492 Switch
07-3152 Circuit Breaker
07-1824 Rubber Boot
2
11
1
3
20
22
18
4
14
8
7
16
10
20
16
11
18
13
17
Item Part
Qty
Description
1. 03-0457 1
Barb, 6, 6MP, Nylon
2. 03-1226 1
Barb, 10, 8MP
3. 03-1326 1
Pump, Flojet, Water, 2.1 gpm, 12 volt
03-2558 1
Pump, Flojet, Water, 2.9 gpm, 24 volt
4. 03-3537 2
O-Ring, #8, Face Seal
5. 07-0140 4
Washer, Lock, Gr2, #10
6. 07-0141 4
Nut, Hex, Gr2, 10-24
7. 07-0413
2
Nozzle, Cap, Nylon,
NOTE 1: MOUNT SPRINKLER KIT IN THIS
POSITION
WHEN USING
180 DEGREE Tip, Brass
8. 07-0414HOOD
2
Nozzle,
OR DIRT DEFLECTOR
OPTION.
9. 07-0532 1
Strainer, Hypro, Water
10. 07-0547 1
Clamp, Spring, 7/8 Hose
11. 07-0549 6
Clamp, Spring, 5/8 Hose
12. 07-1430 8
Washer, Flat, #10
13. 07-3869 1
Fitting, Barb, Tee, Nylon, 3/8
14. 07-4804 1
Grommet, Rubber, 1-1/4 x 7/8 x 1/16
15. 07-4831 4
Screw, BHC, 10-24UNC, 2B x 3/4
Item Part
Qty
Description
16.
17.
18.
19.
20.
21.
22.
23.
2 1.25ft 1.5ft 1.75ft 2ft 2.5ft 1.25ft 1.5ft 1.75ft 2ft
2.5ft
20ft 1
1 1 1 Nozzle, Elbow, without Clamp
Hose, Clear, Vinyl, 3/8, 5 ft
Hose, Clear, Vinyl, 3/8, 6 ft
Hose, Clear, Vinyl, 3/8, 7 ft
Hose, Clear, Vinyl, 3/8, 8 ft
Hose, Clear, Vinyl, 3/8, 9 ft
Hose, Clear, Vinyl, 3/8, 5 ft
Hose, Clear, Vinyl, 3/8, 6 ft
Hose, Clear, Vinyl, 3/8, 7 ft
Hose, Clear, Vinyl, 3/8, 8 ft
Hose, Clear, Vinyl, 3/8, 9 ft
Hose, Clear, Vinyl, 3/8
Valve, Shut-Off, 1/2, Nylon
Fitting, Nipple, 1/2, Nylon
Fitting, Nipple, 1/2 x 3/8, Nylon
Wire, Harness, with Box
07-4862
07-5127
07-5127
07-5127
07-5127
07-5127
07-5127
07-5127
07-5127
07-5127
07-5127
07-5127
07-6862
07-6863
07-6864
LAF8316
50
51-3880, 11/08
OPTIONS SECTION
SPRINKLER SYSTEM
Dust Suppression System
Spray Bar Nozzle Mount
12 Volt 24 Volt
11-4190 (5 Ft [1.3m]) 11-4379 (8/9 Ft [2.0m])
11-4045 (6 Ft [1.5m])
11-4171 (7 Ft [1.8m])
11-4062 (8 Ft [2.0m])
11-4262 (9 Ft [2.7m])
Replacement Parts for 03-1326 and 03-2558 :
07-6565 Fan Shroud
07-6566 Grommet Set (Qty 4)
07-6567 Motor Base Plate
Item Part
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Qty
03-0076 1
03-0457 1
03-0819 2
03-1326 1
03-2558 1
03-1709 2
07-0343 1
07-0411 3
07-0411 5
07-0412 2
07-0413 5
07-0413 7
07-0414 4
07-0414 6
07-0417 1
07-0532 1
07-0547 2
07-0549 10
07-0549 14
07-0867 4
07-0917 20ft
07-0929 1
Description
Nipple, 6MP-6MP, BP, Close
Barb, 6, 6MP, Nylon
Fitting, 6FP-8MP
Pump, Flojet, Water, 2.1 gpm, 12 volt
Pump, Flojet, Water, 2.9 gpm, 24 volt
Barb, 10, 6MP, Nylon
Switch, Toggle, 2 Position
Nozzle, Tee, with Clamp (5/6/7)
Nozzle, Tee, with Clamp (8)
Nozzle, Elbow, with Clamp
Nozzle, Cap, Nylon, (5/6/7)
Nozzle, Cap, Nylon, (8)
Nozzle, Tip, Brass (5/6/7)
Nozzle, Tip, Brass (8)
Fitting, Barb, Brass, 3/8
Strainer, Hypro, Water
Clamp, Spring, 7/8 Hose
Clamp, Spring, 5/8 Hose (5/6/7)
Clamp, Spring, 5/8 Hose (8)
Terminal, Butt
Wire, Bulk, Cord, 16 Gauge
Terminal, Ring, 3/8, 16-14
Item Part
Qty
18. 07-1716 4
19. 07-1718 4
20. 07-3279 4
21. 07-3638 4
22. 07-3654 4
23. 07-4032 4
24. 07-4038 4
25. 07-4039 4
26. 07-4673 2
28. 09-0028 7ft
09-0028 10ft
29. 09-0056 23.75ft
09-0056 25ft
09-0056 26.25ft
09-0056 27.5ft
09-0056 28.75ft
32. 13-2164 1
11-6684 1
13-2812 1
33. 13-10076 2
Description
Bolt, Carriage, 3/8-16 x 1
Washer, Lock, Split, 3/8
Washer, Flat, 3/8
Screw, Cap, 1/4-20 x 1 1/4
Nut, Hex, 3/8-16
Washer, Flat, 1/4
Washer, Lock, Split, 1/4
Nut, Hex, 1/4-20
U-Bolt, Standard, 1/4-20 x 1
Hose, Heater, 5/8(5/6/7)
Hose, Heater, 5/8 (8/9)
Hose, Heater, 3/8 (5)
Hose, Heater, 3/8 (6)
Hose, Heater, 3/8 (7)
Hose, Heater, 3/8 (8)
Hose, Heater, 3/8 (9)
Tube, RD, 7/8 x 16 Gauge x 60 (5)
Tube, RD, 7/8 x 16 Gauge x 72 (6/7)
Tube, RD, 7/8 x 16 Gauge x 92.37 (8/9)
Plate, Mounting, Sprinkler Bar
51-3880, 11/08
51
OPTIONS SECTION
SIGHT INDICATOR KITS
Sight Indicators
Kit: 28-9965
2
Item Part
1.
2.
3.
4.
5.
Qty
07-3279 2
07-4036 2
07-6597 4
13-14857 2
13-9567 2
Description
Washer, Flat, Gr8, 3/8
Nut, Hex, Nylock, 3/8-16
Screw, HFH, CL10.9, M6-1 x 30
Weld, Sight Indicator
Ball, 2 1/8, Red, with Hole
1
5
4
3
Kit: 11-5897
52
51-3880, 11/08
OPTIONS SECTION
CONVERSION KIT
Manual to Hydraulic
Single Motor
Kit: 28-10133
Return from Brush Head
3
8
10
4 6
11
Return to Skid Steer
7
5
1
9
2
Item Part
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Qty Description
03-2291 4
03-2352 2
03-2396 1
03-4700 1
03-4887 1
03-5215 1
07-0206 2
07-4622 2
07-7131 2
13-11248 2
LAF9441 1
Fitting, 6MF-6MB, 6F50L0-S
Hose, .38 x 32, 6FF-6FF90, 4.75K
Elbow, 90, 10MF-12MP
Elbow, 45, 10MF-12MB
Cylinder, 2.50 x 1.38 x7.50, 3.5K Ball-Cross Tube
Manifold, Swing, with Relief, 12 Volt
Pin, Cotter, Gr2, 3/16 x 2
Nut, Hex, Lock, CL10.9, M10-1.5
Screw, HHC, CL10.9, M10-1.5 x 160mm
Bushing, 1 x .406 x 1
Wire, Assembly, 9 Ft
Replacement Parts for 03-4887 :
03-4888 Seal Kit
03-5035 Cylinder Rod
Replacement Parts for 03-5215 :
07-7150 Valve, Cartridge, Pressure, Comp
07-7151 Valve, Cartridge, Relief
07-7152 Valve, Cartridge, Directional
07-7153 Coil, 12 Volt
51-3880, 11/08
53
OPTIONS SECTION
CONVERSION KIT
Manual to Hydraulic
Dual Motor
8
rn
tu
Re
id
Sk
r
ee
St
hH
ea
d
6
to
Kit: 28-10134
Br
us
10
Re
tur
nf
ro
m
4
13
9
5
2
Item
1.
2.
3.
4.
5.
6.
7.
8.
9
10.
11.
12.
13.
Part
03-2291 4
03-2352 2
03-2396 1
03-4700 1
03-4887 1
03-5173 1
03-5215 1
03-5385 1
07-0206 2
07-4622 2
07-7131 2
13-11248 2
LAF9441 1
3
QtyDescription
Fitting, 6MF-6MB, 6F50L0-S
Hose, .38 x 32, 6FF-6FF90, 4.75K
Elbow, 90, 10MF-12MB
Elbow, 45, 10MF-12MB
Cylinder, 2.50 x 1.38 x 7.50, 3.5K Ball-Cross Tube
Hose, .63 x 60, 10FF-12FF, 3.625K
Manifold, Swing, with Relief, 12 Volt
Hose, .63 x 80, 10FF-10MB, 3K, HS
Pin, Cotter, Gr2, 3/16 x 2
Nut, Hex, Lock, CL10.9, M10-1.5
Screw, HHC, CL10.9, M10-1.5 x 160mm
Bushing, 1 x .406 x 1
Wire, Assembly, 9 Ft
Replacement Parts for 03-4887 :
03-4888 Seal Kit
03-5035 Cylinder Rod
Replacement Parts for 03-5215 :
07-7150 Valve, Cartridge, Pressure, Comp
07-7151 Valve, Cartridge, Relief
07-7152 Valve, Cartridge, Directional
07-7153 Coil, 12 Volt
1
12
7
11
54
51-3880, 11/08
Appendix
QC Series Angle Brooms
Table of Contents
Bolt Torque Specifications........................................ 55
Hydraulic Fittings Torque Specifications.............56-57
Glossary..............................................................58-59
Warranty Information...........................................60-61
51-3880, 11/08
55
APPENDIX
TORQUE SPECS.
NOTE - Nylock nuts are utilized when greater resistance to vibrating loose is required, and greater operating temperatures are
not a factor. In addition, like lock nuts, nylock nuts have a safety feature that if the bolt does vibrate loose, the nut will
remain on the screw. Install nylock nuts to the standard torque shown above.
56
51-3880, 11/08
APPENDIX
TORQUE SPECS
Hydraulic Torque Specifications
Face Seal: Assembly, Tube to Fitting
Note - Face seal fittings have the most reliable sealing method and therefore, should be used
whenever possible.
Installation
1. Make sure threads and sealing surfaces are free of burrs, nicks, scratches, or any foreign materials.
2. Install proper SAE o-ring to end of fitting if not already installed. Ensure o-ring is fully seated and retained properly.
3. Lubricate o-ring with a light coating of clean hydraulic oil.
4. Position tube and nut squarely on face seal of fitting and tighten nut finger tight.
Torque Values:
SAE Dash Size
-4 -6 Tube Side
Thread Size
In-lbs
Ft-lbs
9/16 - 18
220 ± 10
18 ± 1
320 ± 25
27 ± 2
11/16 - 16
-8
13/16 - 16
480 ± 25
40 ± 2
-10
1- 14
750 ± 35
63 ± 3
-12
1 3/16 - 12
1080 ± 45
90 ± 4
-16
1 7/16 - 12
1440 ± 90
120 ± 8
-20
1 11/6 - 12
1680 ± 90
140 ± 8
-24
2 - 12
1980 ± 100
165 ± 8
NOTE - ft-lb may be converted to NewMeters by multiplying by 1.35582.
NOTE - in-lbs may be converted to Newton Meters by multiplying by 0.11298.
51-3880, 11/08
57
APPENDIX
TORQUE SPECS.
Hydraulic Torque Specifications
Straight Thread O-ring Fitting: Assembly, Fitting to Port
NOTE - Straight thread o-ring fittings are utilized to adapt hydraulic systems to
motors, pumps, cylinders, and valves.
Installation (Adjustable Fitting)
1. Make sure threads and sealing surfaces are free of burrs, nicks, scratches, or any foreign materials.
2. Install proper SAE o-ring on port end of fitting if not already installed. Ensure o-ring is fully seated and retained properly.
3. Lubricate o-ring with a light coating of clean hydraulic oil.
4. Back off nut as far as possible and push washer up as far as possible. (Figure 4 & 5)
5. Screw fitting into port. Hand tighten fitting until backup washer contacts face of port. (Figure 6)
6. To position the fitting, unscrew to desired position, but not more than one full turn.
7. Hold fitting in position with wrench. Using appropriate torquing device, tighten nut to given torque rating from the table in
section. (Figure 7)
Torque Values
Figures 4, 5, 6 and 7
Fitting
Size
SAE Port
Thread Size
-4
7/16 - 20
190 ± 10
16 ± 1
-6
9/16 - 18
420 ± 15
35 ± 1
-8
3/4 - 14
720 ± 25
60 ± 2
-10
7/8 - 14
1260 ± 50
105 ± 5
-12
1 1/16 - 12
1680 ± 75
140 ± 6
-16
1 5/16 - 12
2520 ± 100
210 ± 8
-20
1 5/8 - 12
3100 ± 150
260 ± 12
-24
1 7/8 - 12
3800 ± 150
315 ± 12
In-Lbs
Ft-Lbs
NOTE - ft-lb may be converted to NewMeters by multiplying by 1.35582.
NOTE - in-lbs may be converted to Newton Meters by multiplying by 0.11298.
58
51-3880, 11/08
APPENDIX
GLOSSARY
angle or angle assembly - portion of the sweeper that allows
the brush head assembly to angle.
manual angle kit - means of swinging the brush head
assembly mechanically.
BP - black pipe.
mid pump unit - sweeper in which the pump is mounted on
the mid PTO.
brush head assembly - assembly that includes the core,
hood, and brush frame.
brush pattern - area of dirt removed from sweeping surface;
with a properly adjusted sweeper; the pattern is the same
width for the entire length.
castellated - having battlements like a castle.
caution - indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
core - weldment that holds brush sections.
danger - indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
F - female.
mounting assembly - portion of the sweeper that attaches to
the prime mover; designed specifically for each prime mover.
NPT - national pipe thread.
note - indicates supplementary information.
OR - o-ring.
psi - pounds per square inch.
PTO - power take off; shaft on the prime mover used to drive
attachments.
plate swing - swing assembly that includes a half-moon
plate.
FS - face seal.
power pack - auxiliary hydraulic package used when prime
mover hydraulics do not have enough flow available.
front - side that is in front when facing the normal forward
direction of travel of the machine.
prime mover - refers to the tractor, truck, loader or other
vehicle to which a sweeper is attached.
gpm - gallons per minute.
qty - quantity.
HP - high pressure.
quick change core - core designed in a way that allows
brush sections to be changed without removing hoses from
motors.
hood - brush shield.
hydraulic angle kit - means of swinging an assembly
hydraulically.
important - used for instructions when machine damage
may be involved.
in. - inches.
kph - kilometers per hour.
lb - pounds.
left-hand - side that is on the left when facing the normal
forward direction of travel of the machine.
lift cylinder - means of raising the brush head assembly
hydraulically.
lps - liters per second.
M - male.
mm - millimeters.
mph - miles per hour.
rpm - revolutions per minute.
rear - side that is in rear when facing the normal forward
direction of travel of the machine.
rear pump unit - sweeper in which the pump is mounted on
a rear PTO.
retainer - removable plate or set of plates that keeps
sections on the core.
right-handed - side that is on the right when facing the
normal forward direction of travel of the machine.
section - single brush wafer.
section set - replacement brush wafers.
sprinkler system - system that sprays water ahead of the
sweeper used to reduce dust.
sprinkler tank - assembly that includes the water reservoir
and mounting used in a sprinkler system.
stands - devices designed to keep the components off the
ground when the sweeper is dismounted.
51-3880, 11/08
59
APPENDIX
GLOSSARY
swing or swing assembly - portion of the sweeper that
allows the brush head assembly to angle.
swing cylinder - means of angling the brush head assembly
hydraulically.
tank assembly, hydraulic - assembly that includes the
hydraulic reservoir, filter and fittings; may also incorporate
valves.
warning - indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
weld - weldment.
windrow - pile of debris.
zerk - grease fitting.
60
51-3880, 11/08
APPENDIX
WARRANTY INFORMATION
Warranty Registration Form & Delivery Inspection Report
IMPORTANT! Warranty Void if card is not returned within 10 days.
All Applicable sections must be filled in.
This section to be filled out and signed by Dealer at time of delivery.
Customer’s Name
Address
City
Phone
State
Zip
Dealer’s Name
Address
City
State
Zip
CHECK ONE:
Loader / Tractor Model
Delivery Date
Brand & Model #
Serial #
Agricultural Use
Construction Use
Landscape Use
O ther
Dealer Inspection (check items applicable)
All Decals Installed (see operator's manual)
Review Operating & Safety Instructions
Hydraulic Fittings Tight & Free of Leaks
Guards & Covers in Place & Secure
Fastners Tight
Does Product Function Properly
I have thoroughly instructed the buyer on the above described equipment. This review included: The Operator’s Manual
content, equipment care, adjustments, safe operation and applicable warranty policy.
Dealer Rep. Signature:
Date:
This section to be completed and signed by the Owner
QUALITY ASSURANCE RATING
1=Excellent
2=Good
3=Average
4=unsatisfactory
Question
Quality of Product: Appearance
Construction
Quality of Service
Value (Priced Fairly)
Does it perform as claimed
Paladin Light Construction
Local Dealer
5=poor
The above described equipment and Operator’s Manual have been received by me and I have been thoroughly instructed as
to care, adjustments, safe operation and applicable warranty policy.
Owner’s Signature:
Date:
NOTE! Make one copy each for the dealer’s and owner’s records. Fax or mail to the appropriate Paladin Light
Construction Division.
Bradco McMillen The Major
PO Box 266 Delhi IA 52223
Fax 563.922.2700
Warranty Form 0706-1
FFC
100 East Lee Rd Lee IL 60530
Fax 815.824.2620
www.paladinbrands.com
Sweepster Harley
2800 North Zeeb Rd Dexter MI 48130
Fax 734.996.9014
51-3880, 11/08
61
APPENDIX
WARRANTY INFORMATION
SWEEPSTER ATTACHMENTS LLC
Limited 12 Month Warranty
Thank you for purchasing a Sweepster Attachments, LLC. product. Warranty protection is
valid only when this Warranty Registration is completed and signed by the customer and
dealer, and mailed to Sweepster Attachments,LLC. I hearby acknowledge that I have received
a copy of the owners Limited Warranty and I accept the terms therein.
For a period of 12 months from the date of delivery of product to the original user, Sweepster
Attachments, LLC. warrants each product to be free from manufacturing defects, subject to the
limitations contained in this policy.
This warranty does not apply to defect caused, in whole or in part, by unreasonable use while
in the possession of the user, including, but not limited to: failure to properly set up product;
failure to provide reasonable and necessary maintenance; normal wear; routine tune ups or
adjustments; improper handling or accidents; operation at speed or load conditions contrary
to published specification; improper or insufficient lubrication; improper storage. This
warranty is also not a guarantee that performance of each product will meet the expectations
of the purchaser.
Sweepster Attachments, LLC. shall not be liable for consequential damages of any kind,
including, but not limited to: consequential labor costs or transportation charges in connection with the
replacement or repair of defective parts; lost time or expense which may have accrued
because of said defects. In no event shall Sweepster Attachments, LLC.’s total liability
hereunder exceed the product purchase price.
Sweepster Attachments, LLC. makes no warranty with respect to trade accessories or any
component or accessory of the product which was not manufactured by Sweepster Attachments, LLC. including any purchased components of any kind. These are subject to the
warranties of their respective manufacturers. The warranty will be considered void if the
product or any part of the product is modified or repaired in any way not expressly authorized
by Sweepster Attachments, LLC. or if closed components are disassembled prior to return.
Closed components include, but are not limited to: gearboxes, hydraulic pumps, motors,
cylinders, and actuators.
Our obligation under the warranty is expressly limited, at our option, to the replacement or
repair at Sweepster Attachments, LLC or at a service facility designated by us, or such part or
parts as inspection shall disclose to have been defective. We are not responsible for unauthorized repairs or replacements. Any implied or statutory warranties, including any warranty
of merchantability or fitness for a particular purpose, are expressly limited to the duration of
this written warranty. We make no other express or implied warranty, nor is anyone authorized to make any on our behalf. This warranty cannot be extended, broadened, or changed
except in writing by an authorized officer of Sweepster Attachments, LLC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement