TVLogic LVM-095W-N2, SRM-095W-N Operation Manual

PDF Download

Document

Multi Format Broadcast

LCD Monitor

Operation Manual_v3.3

LVM-095W-N2

SRM-095W-N

Contents

1. Caution

...........................................................................

2. Main Features

...................................................................

3. Controls & Functions

...........................................................

4. Menu Tree & Adjustment

5. Menu Operations

......................................................

...............................................................

[1] Picture

........................................................................

[2] Color

[3] Marker

..........................................................................

........................................................................

[4] GPI/UMD

....................................................................

[5] Waveform

[6] Audio

....................................................................

..........................................................................

[7] Display & Set

................................................................

6. Button Functions

7. Other Functions

...............................................................

................................................................

8. Product Speci

cations

........................................................

9. Optional Accessories

.........................................................

16

18

21

12

13

14

22

25

27

35

37

04

06

07

11

12 FCC (Federal Communications Commission)

This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential to correct the interference at his own expense

CAUTION: Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packing indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequence for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.

Multi Format LCD Monitor 3

1. Caution

• Always use set voltage. (DC 12~24V)

• When using a DC Adapter other than the

one supplied by the manufacturer, please

be advised that the adapter with

DC 12V/3A ~ 6A can be compatible with

Removing covers can expose you to high

voltage and other dangerous conditions.

Request a qualifi ed service person to perform

servicing.

understood before the product is operated.

These safety and operating instructions must

be kept in a safe place for future reference.

instructions must be observed closely.

by the manufacturer. Use of inadequate

attachments can result in accidents.

source specifi ed on the specifi cation label.

used in your home, consult your dealer or local

power company. For units designed to operate

on batteries or another power source, refer to

the operating instructions.

the power cord from the DC outlet, and request

a qualifi ed service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or

when objects have fallen into the product.

c. When the product has been exposed to rain

or water.

d. When the product does not operate properly

as described in the operating instructions.

Do not touch the controls other than those

described in the operating instructions.

Improper adjustment of controls not described

in the instructions can cause damage,

which often requires extensive adjustment

work by a qualifi ed technician.

e. When the product has been dropped or

damaged.

f. When the product displays an abnormal

condition. Any noticeable abnormality in the

product indicates that the product needs

servicing.

to prevent people from stepping on them or

objects from resting on them. Check the cords

at the plugs and product.

parts, make sure that the service person uses

replacement parts specifi ed by the manufacturer,

or those with the same characteristics and

performance as the original parts. Use of

unauthorized parts can result in fi re, electric

shock and/or other danger.

of the standard adapter provided by the

manufacturer, please check the proper load

capacity (or current capacity) and use an

adapter with stable voltage.

request the service technician to perform safety

checks to ensure that the product is in proper

operating condition.

Overloading can cause or electric shock.

vents or openings. High voltage in the

product, and inserting an object can cause

electric shock and/or short internal parts. For

the same reason, do not spill water or liquid on

the product.

4 Multi Format LCD Monitor

1. Caution

be sure to install the product according to the

method recommended by the manufacturer.

before cleaning the product. Use a damp cloth

to clean the product. Do not use liquid cleaners

or aerosol cleaners.

you do not use the product for considerably

long time.

cabinet are designed for ventilation. Do not

cover or block these vents and openings since

and/or shorten the life of the product. Do not

place the product on a bed, sofa, rug or other

similar surface, since they can block ventilation

openings. This product is not designed for

built-in installation; do not place the product

in an enclosed place such as a bookcase or rack,

unless proper ventilation is provided or the

manufacturer’s instructions are followed.

bathtub, washbasin, kitchen sink and laundry

tub, swimming pool and in a wet basement.

Sunlight.

stand, tripod or table. Placing the product on an

unstable base can cause the product to fall,

resulting in serious personal injuries as well as

damage to the product. Use only a cart, stand,

tripod, bracket or table recommended by the

manufacturer or sold with the product. When

mounting the product on a wall, be sure to

follow the manufacturer’s instruction. Use only

the mounting hardware recommended by the

manufacturer.

the inside of the product may be overheated

due to the heat from other devices nearby and

the decrease of air circulation, which could

damage to the monitor. To prevent the damage,

please have enough space for the monitors

and use a fan to avoid overheating and

maintain the operating temperature. (Refer to

the specifi cation of the product).

glass. Therefore, it can break when the product

is dropped or applied with impact. Be careful

not to be injured by broken glass pieces in case

the LCD panel breaks.

must be moved with the utmost care.

fl oor surface can cause the product to fall from

the cart.

such as radiators, heaters, stoves and other heat

generating products (including amplifi ers).

manufacturered with high precision technology

and has more than two million pixels or more

than six million sub-pixels to reproduce the

high resolution images. But, some of the pixels

in the LCD screen may be stuck to show either

always on (red, green, blue) or always off (black

or dark). TVLogic guarantees more than 99.999%

of the sub-pixels are operating normally and

less than 0.001% of the sub-pixels may be

defective. Some sub-pixels may spontaneously

become defective after long period of time,

but this is not a malfunction of the monitor.

Evaluation of the pixel defect is recommended

to be performed in a dim condition with

the illuminance of more than 100 lux, and the

viewing distance should be more 30cm from

the screen.

Multi Format LCD Monitor 5

2. Main Features

LVM-095W-N2 / SRM-095W-N Monitors contain the following features:

• Compatible with various SDI signals

formats

- This product is compatible with various SDI

signals - 480i, 576i, 720p, 1035i, 1080i, 1080p,

1080psf

• All-in-one type system

- Slim and all-in-one type monitor that

supports various functions that requires no

other accessories.

• Wide Screen / 24Bit RGB FHD Panel

• Waveform/Vector Scope/Audio Level

- Waveform & Vector Scope

- Embedded Audio Level Meter

• Audio In/Out

- Internal Speaker(Embedded audio & External

Audio Input)

- Stereo Audio Out through phone Jack &

External Audio Input

• Knob Control

- Easy to adjust user confi guration using the

control knob on the front of the monitor.

• BLUE ONLY/MONO Function

• H/V delay Function

• Markers & Safety Areas

- Center Marker, Safety Area Marker, Aspect

Marker, Display Size(Scan)

• Pixel To Pixel Function

- Used to display the original image resolution

without scaling.

• External control function

- This product can be controlled by using

parallel switch, RS-422 and Network simply

with cable connection without additional

peripheral equipment attached to the unit.

• RS422/UMD feature support

- This product supports protocols provided by

TVLogic or a TSL protocol.

• Power

- Basically, the product is powered by a

normal DC source.

- The product can be battery-powered.

* LVM-095W-N2 / SRM-095W-N : DC12V/24V

* When using a DC Adapter other than the one

supplied by the manufacturer, please be

advised that the adapter with DC 12V/3A ~ 6A

can be compatible with the monitor.

• Additional features

- Loop Through (SDI), VESA Mounting Standard,

OSD user interface and Rack Mountable.

- LVM-095W-N2 : 400cd/ m 2

Luminance, 750 : 1

Contrast

- SRM-095W-N : 800cd/ m 2

Luminance, 750 : 1

Contrast

6 Multi Format LCD Monitor

3. Controls & Functions

LVM-095W-N2 / SRM-095W-N : FRONT

CHROMA

BRIGHT

APERTURE

SOURCE

SDI

SPEAKER-LEFT

SCAN

ASPECT

MARKER

H/V DELAY

BLUE/MONO

W-FORM/VECTOR

LVM-095W-N2 / SRM-095W-N : REAR

TALLY

SDI-IN A/B

SDI-OUT

RS-422 IN

RS-422 OUT

AUDIO IN

AUDIO OUT

HDMI

POWER

ENTER

DOWN

CONTRAST

VOLUME

SPEAKER-RIGHT

TALLY

REMOTE

USB

DC IN

Multi Format LCD Monitor 7

3. Controls & Functions

LVM-095W-N2 / SRM-095W-N : FRONT

• [SDI] Button/Lamp

- Used to select SDI-A/B input.

• [SOURCE] Button/Lamp

- Used to select Composite input or HDMI input.

• [SCAN] Button/Lamp

- Used to change the scan mode.

- Press the button to activate through the scan

modes: [ZEROSCAN] -> [OVERSCAN] -> [PIXEL

TO PIXEL] -> [USER ASPECT] -> [ZEROSCAN]

* PIXEL TO PIXEL mode is not available in

graphic mode.

* [USER ASPECT]: User can adjust width and

height of the display.

* Check “7. Other Functions [1] User Aspect” for

more information.

• [ASPECT] Button/Lamp

- Used to change the various display ratio.

Activates in order of [16:9] – [4:3] – [2.35:1] -

[1.85:1] – [15:9] – [16:10] – [AUTO] – [16:9].

• [MARKER] Button/Lamp

- Used to activate/deactivate the Marker. The

type of marker at work can be selected on the

main menu.

• [HVDELAY] Button/Lamp

- Used to check horizontal sync and vertical

sync simultaneously by moving the display

left, right, up and down.

- In this mode, the brightness of the image

automatically increase for easy verifi cation of

synchronized signals.

• [BLUE]/[MONO] Button/Lamp

- Activates in the order of [Off ]-[Blue Only]-

[Mono]-[Off ]

- Press the button to remove red and green

from the input signal and display the screen

only under a blue signal. Press the button

again to activate mono mode.

• [Waveform/VECTOR] Button/Lamp

- Used to activate/deactivate the Waveform.

- The type of Waveform at work can be selected

on the main menu.

• [F1][F2][F3] Button/Lamp

- Used to activate the [F1]~[F3] function.

* Check “7. Other Functions [1] User Aspect” for

more information.

8 Multi Format LCD Monitor

3. Controls & Functions

LVM-095W-N2 / SRM-095W-N : FRONT

• [MENU] Button

- Used to activate the OSD menu.

- When the OSD menu is activated, press this

button to exit from the menu.

• [UP] / [DOWN] Button

- Used to move within the menu when the OSD

menu is activated and is also used to increase

or decrease the value of selected feature.

• [ENTER] Button

- Used to select the feature of main menu and

the sub menus.

• [POWER] Switch

- Used to turn the power on and off . If the signal

is normal, Green LED light is indicates. If the

signal is unsupported or disconnected, LED

light fl ashes in Yellow.

• [STANDBY] lamp

- Used to indicate the power supply status.

The lamp is RED during power supply and

GREEN during system is in operation. In case

of power cut and sudden shut off of the

power, our monitor keep previous setup

stage.

• [TALLY] Lamp

- Tally lamp that can be toggled in green or red

using the REMOTE(RJ-45) port or RS-422 serial

communication.

• [APERTURE] Knob

- Used to adjust the picture sharpness.

- The value is selectable between -12 ~ 12.

• [BRIGHT] Knob

- Used to adjust the degree of brightness.

- The value is selectable between -100 ~ 100.

• [CHROMA] Knob

- Used to adjust the saturation of the image.

- The value is selectable between -50 ~ 50.

• [CONTRAST] Knob

- Used to adjust the contrast.

- The value is selectable between -100 ~ 100.

• [VOLUME] Knob

- Used to adjust the volume for internal speaker

and external output.

- The value is selectable between 0 ~ 30.

Multi Format LCD Monitor 9

3. Controls & Functions

LVM-095W-N2 / SRM-095W-N : REAR

• TALLY(LAMP)

- Interlocks with front tally lamp.

• SDI-A (BNC)

- HD/SD SDI signal input.

• SDI-B / CVBS (BNC)

- HD/SD SDI signal or CVBS signal input

• AUDIO IN (Phone jack)

- Internal speakers stereo audio input terminal.

• AUDIO OUT (phone jack)

- Built in audio disembedder and internal

speakers stereo audio output.

• USB

- This terminal is used to upgrade the fi rmware

or color calibration made by TVLogic.

• REMOTE (RJ-45)

- Provides connection to control equipment for

external monitor control.

- Features can be changed in the REMOTE

section of OSD menu.

• DC IN (XLR, 4 pins)

- DC power input terminal for DC 12V/24V.

* When using a DC Adapter other than the one

supplied by the manufacturer, please be

advised that the adapter with DC 12V/3A ~ 6A

can be compatible with the monitor.

DC IN socket

1: GND

4: +12V/

+24V

* When using a DC Adapter other than the one

supplied by the manufacturer, please be

advised that the adapter with DC 12V/3A ~ 6A

can be compatible with the monitor.

< Warning >

When using the product make sure to ground, whenever possible, before connecting the input signal cable in order to prevent any possible damage to the product or connected devices. The damage may include signal noise, malfunction of main board or display panel.

And the connected devices such as camera or video source player may also be infl uenced through signal cable. Please check if the AC power source and the power extender or power distributor is grounded.

10 Multi Format LCD Monitor

4. Menu Tree & Adjustment

[1] Menu Tree

• OSD(On-Screen Display) Menu helps you

use various functions.

• This Picture is the menu structure for

LVM-095W-N2 / SRM-095W-N

[3] Menu Control Sequence

• Menu Control sequence follows the order

below:

1. Press the MENU button to activate the OSD

menu.

2. Move to a desired menu with the UP/DOWN

button.

3. Press the ENTER button to select a menu

and move to a sub-menu with the UP/DOWN

button.

4. Press the ENTER button to select the desired

sub-menu. (The selected sub-menu will be

highlighted)

5. Press the ENTER button or the MENU button

to save the new value after adjusting the

value with the UP/DOWN button.

6. Press the MENU button to return to the

previous menu and if there is no previous

menu, the OSD menu will be removed from

the screen.

[2] Menu Control

• User may control various functions using

the MENU, UP, DOWN, ENTER buttons on

the bottom front of the monitor.

Multi Format LCD Monitor 11

5. Menu Operations

[1] Picture

• NTSC Setup

- This function is not supported since the

LVM-095W-N2 / SRM-095W-N doesn’t

support Analog input signal.

• Knob Lock

- Locks the Knob control Knob(Aperture,

Bright, Chroma, Contrast, Volume).

• Brightness

- Used to set the brightness(=off set) level from

-100 to 100.

* Brightness can be adjusted by using [BRIGHT]

control knob on the front of the monitor.

• Contrast

- Used to set the contrast(gain) level from -100

to 100.

* Contrast can be adjusted by using [CONTRAST]

control knob on the front of the monitor.

• Chroma

- Used to set the saturation level from -50 to 50.

* Chroma can be adjusted by using [CHROMA]

control knob on the front of the monitor.

• Phase

- This function is not supported since the

LVM-095W-N2 / SWM-095W doesn’t support

Analog input signal.

• Aperture

- Used to set the sharpness level from -12 to 12.

* Aperture can be adjusted by using [Aperture]

control knob on the front of the monitor.

12 Multi Format LCD Monitor

5. Menu Operations

[2] Color

• Color Temp.

- Used to select the among preset color

temperatures or adjust the customized color

temperature of the monitor.

- Preset color temperatures are 5600K, 6500K,

9300K and User1/2/3.

- In User 1/2/3 modes, user can defi ne custom

RGB GAIN, BIAS (=Off set) and ColorCopy

values.

• Gain Red

- Used to set Red Gain(or Picture, Contrast) level

from -256 to 255.

* Only available in User 1/2/3 mode.

• Gain Green

- Used to set Green Gain(or Picture, Contrast)

level from -256 to 255.

* Only available in User 1/2/3 mode.

• Gain Blue

- Used to set Blue Gain(or Picture, Contrast)

level from -256 to 255.

* Only available in User 1/2/3 mode.

• Bias Red

- Used to set Red Bias(or Off set, mainly aff ects

on Black level) from -100 to 100.

* Only available in User 1/2/3 mode.

• Bias Green

- Used to set Green Bias(or Off set, mainly aff ects

on Black level) from -100 to 100.

* Only available in User 1/2/3 mode.

• Bias Blue

- Used to set Blue Bias(or Off set, mainly aff ects

on Black level) from -100 to 100.

* Only available in User 1/2/3 mode.

• Color Copy

- Used to copy the R/G/B Gain value of pre-

stored color temperature settings.

- In User mode, fi nd and select the color

temperature and press the Enter button to

copy and apply the Gain value to Gain Red,

Gain Green, Gain Blue.

* Only available in User 1/2/3 mode.

• Temperature Adaptive Color

- [On] : Used to measure and compensate

the color temperature shift caused by panel

temperature variation.

- [Off ] : Used to apply preset color temperature

setting regardless of the panel temaperature.

• Gamma

- Used to change the Gamma Curve between

2.2 and 2.4.

Multi Format LCD Monitor 13

5. Menu Operations

[3] Marker

• Fit Marker

- Used to activate or inactivate the Fit Marker

function.

- When the Marker type is selected in the

Marker menu, a border line of the Safety Area

will be displayed inside the Marker. Images

below show the diff erence between Fit

Marker On and Off .

• Marker

- Used to activate the Marker function.

- Available marker types are Off , 16:9, 4:3, 4:3

ON AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 &

4:3 and User.

* This function operates only after activating

the Marker function by pressing the MARKER

button on the front of the monitor.

• Center Marker

- Displays the Center Marker on the screen.

* This function operates only after activating

the Marker function by pressing the MARKER

button on the front of the monitor.

• Safety Area

- Used to select to display and control the size

and availability of the Safety Area.

- Available sizes are 80%, 85%, 88%, 90%, 93%,

100%, EBU ACTION 16:9, EBU GRAPHIC 16:9,

EBU ACTION 14:9, EBU GRAPHIC 14:9, EBU

ACTION 4:3 and EBU GRAPHIC 4:3.

* This function operates only after activating

the Marker function by pressing the MARKER

button on the front of the monitor.

MARKER : 4:3

SAFETY AREA : 90%

FIT MARKER : OFF

MARKER : 4:3

SAFETY AREA : 90%

FIT MARKER : ON

• Marker Mat

- Used to set the darkness level outside of the

Marker area from Off (transparent) to

7(Black).

- The bigger the value, the darker the color.

• Marker Color

- Used to set the color of the Marker lines.

Available colors are White, Gray, Black, Red,

Green and Blue.

• Thickness

- Used to set the thickness of the Makrer lines.

- Thickness level is from 1 to 7 by the pixel unit.

14 Multi Format LCD Monitor

5. Menu Operations

[3] Marker

• User Marker H1

- Used to set the position of the fi rst horizontal

marker line.

- Displayed when Marker menu is set to User.

• User Marker H2

- Used to set the position of the second

horizontal marker line.

- Displayed when Marker menu is set to User.

• User Marker V1

- Used to set the position of the fi rst vertical

marker line.

- Displayed when Marker menu is set to User.

• User Marker V1

- Used to set the position of the second vertical

marker line.

- Displayed when Marker menu is set to User.

Multi Format LCD Monitor 15

5. Menu Operations

[4] GPI / UMD

• This item activates/ deactivates the

- The user may connect an RJ-45 jack to the

REMOTE terminal on the rear of the unit and

designate a function for each pin.

PIN 1 : HDMI Channel

PIN 2 : SDI-A Channel

PIN 3 : SDI-B Channel

PIN 4 : Tally R

PIN 5 : Tally G

PIN 6 : Blue Only

PIN 7 is POWER ON/OFF use only, PIN 8 is GND.

- The selectable values are as follows :

REMOTE (RJ-45)

1 8

1: Pin1

2: Pin2

3: Pin3

4: Pin4

5: Pin5

6: Pin6

7: Pin7

8: GND

- The selectable values are as follows :

Classifi cation

Settable Values

1~6

None,

HDMI CHANNEL,

SDI-A CHANNEL,

SDI-B CHANNEL

TALLY RED,

TALLY GREEN

BLUE ONLY

UNDERSCAN

ASPECT

HVDELAY

16:9 MARKER,

15:9 MARKER,

14:9 MARKER

13:9 MARKER,

4:3 MARKER,

4:3 ON AIR MARKER

1.85:1 MARKER,

2.35:1 MARKER,

1.85:1 & 4:3 MARKER

CENTER MARKER

SAFETY AREA 80%,

SAFETY AREA 88%,

SAFETY AREA 90%

SAFETY AREA 93%,

SAFETY AREA 100%

16 Multi Format LCD Monitor

5. Menu Operations

[4] GPI / UMD

• Monitor ID

- Sets the ID of each monitor for the TVLogic

control protocol or DYNAMIC UMD using RS-

422 communication.

- Available values are between 0 ~ 125.

• UMD Display

- This item sets UMD, ANC and DYNAMIC UMD.

* UMD : Displays user customized characters on

screen.

* ANC: Displays characters embedded in SDI

signal.

* D-UMD(TVL S8C) : Displays incoming data of

8 characters and tally signal from TVLogic

remote control program.

* D-UMD(TVL S16C) : Displays incoming data

of 16 characters and tally signal from TVLogic

remote control program.

* D-UMD(TVL D8C) : Displays incoming data

of two pairs of 8 character strings and tally

signals from TVLogic remote control program.

* D-UMD(TSL S8C) : Displays incoming data of 8

characters and tally signal from TSL protocol.

* D-UMD(TSL S16C) : Displays incoming data of

16 characters and tally signal from TSL protocol

(V3.1).

* D-UMD(TSL D8C) : Displays incoming data

of two pairs of 8 character strings and tally

signals from TSL protocol.

• UMD Character

- Customizes the characters for Under Monitor

Display.

- Alphabets, numbers and special symbols are

available.

- Maximum of 5 characters can be used.

• UMD Character Color

- Used to set the character color of UMD.

- Available colors are White, Red, Green,

Blue, Yellow, Cyan and Magenta.

- This function is activated when the [D-UMD

tally type] is in the [Default], [User color], [BG.

Color], [User tally] and [User BG] modes.

• UMD BG. Trans

- Used to set the transparency of the UMD

background.

- Available values are [Opaque], [50%], [85%]

and [100%].

• UMD Size

- This function adjusts the size of UMD font and

UMD background.

- Available modes are Small and Large.

Multi Format LCD Monitor 17

5. Menu Operations

[4] GPI / UMD [5] Waveform

• D-UMD Tally Type

- Tally type confi guration setting in D-UMD(D-

8C), UMD Display.

- Confi guration values are Default, User

Color, Character, BG. Color, User Tally,

User Char and User BG.

* Default : Existing TV Logic operating system (VRT)

* User Color : User confi guration settings on

each Tally color type.

- Tally1 Color ~ Tally4 Color are activated

when USER COLOR is selected.

* Character : Tally displays with the character

color. Activates the same as Default model.

* BG. Color : Tally is displayed as the

background of character. Activate the same as

Default mode.

* User Tally : The bit0 & bit 1 of TSL Protocol

Control Byte receives the input signal and

displays Tally by user’s set (Off , White, Red,

Green, Blue, Yellow Cyan, Magenta)

* User Char : This function activates in the

same way as User Tally and Tally is displays

by the Character color.

* USER BG. : This function activates in the same

way as User Tally and Tally is displays in the

background of the character.

• Tally1 ~ Tally4 Color

- Used to set the color of each Tally 1, Tally

2, Tally 3 and Tally 4.

- Available colors are Red, Green and Yellow.

• B0:0 B1:0 ~ B0:1 B0:1

- The Byte0, Byte1 of TSL Protocol Control Byte

sets the color of the input conditions.

- Available colors are Off , White, Red, Green,

Blue, Yellow, Cyan and Magenta.

• Press [W-FORM/VECTOR] Button to

activate the Waveform.

• Waveform/Vector

- This function sets the Waveform and

Vectorscope. Available options are diff erent

according to the Input signal.

- Activates in the order:

- YCbCr: Off - Waveform - VectorScope -

Waveform Wide - Waveform YCbCr - Wave_

Vector - Vector_YCbCr - Full Waveform(Y) -

Full VectorScope.

- RGB : Off - RGB.

• Waveform Intensity

- Controls the brightness of the Waveform/

Vector display.

- Available values are between 1 ~ 63. The

higher the number the brighter the waveform

will be.

• Waveform Trans.

- Controls the transparency level of the

Waveform/Vector.

- Available values are OPAQUE and TRANS.

* If the main OSD overlaps with the Waveform/

Vector when the option us set to OPAQUE, it

will automatically display it as transparent

and change back to opaque when the main

OSD disappears.

• Waveform Size

- Controls the size of Waveform/Vector

- Available modes are Normal and Large.

18 Multi Format LCD Monitor

5. Menu Operations

[5] Waveform

• Line Select Enable

- Used to select specifi c Vertical Line for

Waveform/Vectorscope.

- It is available when LINE Waveform is

activated.

- To activate this feature, press the [W-FORM/

VECTOR] Button, then use the [UP]/[DOWN]

Button to select a desired vertical line.

- Control range varies according to the

resolution of the input SDI signal.

* 576i : Min. 1, Max. 625

* 480i : Min. 1, Max. 525

* 720p : Min. 1, Max. 750

* 1080i : Min. 1, Max. 1125

* 1080p : Min. 1, Max. 1125

• Luma(Y’) Zone Check

- Displays the Luma(Y’) level of the input image

in colors.

- May select between [Color Pattern] or [Zebra

Pattern].

- Each pixel’s Y’ analized and changed to a certain

color or zebra pattern according to the Index on

the right side of the screen.

- When a pixel’s Y’ level is under 0%(16), the color /

diagonal line will be colored Green.

- When the pixel’s Y’ level is over 100%(235), the

color / diagonal line will be colored Red.

- When the Y’ level of a pixel is between 0~100%,

the pixel is displayed with Gray, except for

selected Luma Zone.

- In the [Color Pattern] mode, a 5% zone of the

selected Y’ level will be colored Pink(5%) and

±10% will be colored Yellow(-10% from Pink) and

Cyan(+10% from Pink).

- In the [Zebra Pattern] mode, ± 5% of the selected

Y’ Level will be displayed with diagonal lines.

• Luma(Y’) Zone Adjust

- Used to set the Y’ level to be colored Yellow,

Pink and Cyan in [Color Pattern] mode, or to

set Y’ level zone to be displayed with diagonal

lines in [Zebra Pattern] mode.

- Available values are 0 ~ 100%.

* See section “7. Other Functions -> [5] Luma(Y’)

Zone Check” for more information.

Multi Format LCD Monitor 19

5. Menu Operations

[5] Waveform

• Range Error

- Used to set whether or not to activate Y MAX,

Y MIN, C MAX, C MIN, Y PICTURE BLINK and C

PICTURE BLINK functions.

- The values of Y MAX, Y MIN, C MAX, C MIN are

indicated in Waveform/Vectorscope.

- If [Y PICTURE BLINK] or [C PICTURE BLINK] is

enabled, the section of image that exceeds

the selected values of Y MAX, Y MIN, C MAX

and C MIN shall blink.

* In the case of RGB input, Range Error is not

supported.

* See section “7. Other Functions -> [7] Range

Error” for more information.

• Y Max

- Used to set the maximum luma(Y’) level from

0 to 255.

- Pixels with values exceeding the max Y’ level

will blink in the screen, and display in red on

the Waveform.

• Y Min

- Used to set the minimum luma(Y’) level from

0 to 255.

- Pixels with values exceeding the min Y’ level

will blink in the screen, and display in red on

the Waveform.

• C Max

- Used to set the maximum chroma(C’) level

from 0 to 255.

- Pixels with values exceeding the min C’ level

will blink in the screen, and display in red on

the Waveform.

• C Min

- Used to set the minimum chroma(C’) level

from 0 to 255.

- Pixels with values exceeding the min C’ level

will blink in the screen, and display in red on

the Waveform.

• Y Picture Blink

- Used to set whether or not to blink pixels for

values exceeding Y MAX and Y MIN.

• C Picture Blink

- Used to set whether or not to blink pixels for

values exceeding C MAX and C MIN.

20 Multi Format LCD Monitor

5. Menu Operations

[6] Audio

• Volume

- Used to control the output volume of the

internal speakers or [AUDIO OUT] on the back

of the monitor.

- Control range is from 0 to 30.

• Em. Audio Left

- Used to set embedded audio channel for left

audio out of internal speaker or [AUDIO OUT]

terminal on the back of the monitor.

- Available values are between CH1~CH16 and

Ext..

* In the HDMI mode, Left is set to CH1.

• Em. Audio Right

- Used to set embedded audio channel for right

audio out of internal speaker or [AUDIO OUT]

terminal on the back of the monitor.

- Available values are between CH1~CH16 and

Ext..

* In the HDMI mode, Right is set to CH2.

• Level Meter

- Used to set the Level Meter for the embedded

audio.

- Available options are OFF,16 CH(HOR.) and 16

CH(VER.)

* 16 CH(HOR.) : Displays 8 channels on top

left and 8 channels on top right of the screen

horizontally.

* 16 CH(VER.) : Displays 8 channels on center

left and 8 channels on top right of the screen

vertically.

* In the HDMI mode, only 2 channels may be

displayed.

• Level Meter Display

- Used to set the display method for audio level

meter.

- Available modes are Group and Pair.

* In the HDMI mode, the mode is set to Pair.

• Level Meter Reference

- Display the default audio level meter value.

- Available options are -18dB and -20dB.

- Audio level meter within selected value turns

to green and exceeded audio level is displayed

in yellow.

- Audio level exceeding -4dB is displayed in red.

• Level Meter Size

- Used to control the size of the audio level

meters.

- Available options are NORMAL and LARGE.

• Peak Decay Time

- Sets the reduction time for the max value

indication of audio signals.

- Control range is from 0 to 100. Bigger number

means a longer display time for max value.

Multi Format LCD Monitor 21

5. Menu Operations

[7] Display & Set

• System Default

- Used to initialize OSD values to factory default.

• Eco Saving

- Automatically save power consumption if

there is no signal. When signal is fed,

brightness of the monitor will be set as setting

value.

• Back Light

- Used to indicate the backlight level.

- In the case of System Default, the value returns

to factory default(after color calibration).

- Available values are from 0 to 50.

• Internal Pattern

- Generates ColorBar and Grayscale Pattern

internally.

- Selectable range for Gray Pattern is from 0%

to 100% with 5% increment.

* See section “7. Other Function -> [10] Internal

Pattern” for more information.

• H/V Flip

- Allows the displayed image to be fl ipped

horizontally or vertically.

- This feature provides fl exible mounting

options for camera operators.

- Activates in the order : [Off ] – [H Flip] – [V Flip]

– [H/V Flip].

* This function is not supported when the

HDMI input signal’s resolution is over 1920 x

1080 50p.

• 3G Format

- Used to select 3G-SDI A/B input format

among Normal Mode (Auto : A422

10Bit_YCbCr. 50/60p), A 444 10/12Bit_YCbCr,

A 444 10/12Bit_RGB, A 422 12Bit_YCbCr, B

444 10/12Bit_YCbCr, B 444 10/12Bit_RGB, B

422 12Bit_YCbCr, B 422 10Bit_YCbCr 50/60p.

- In NORMAL MODE, the signal is automatically

detected when Payload signal is contained.

* In the HDMI mode, this function is not

supported.

• Firmware Version

- Displays current fi rmware version.

• Serial Number

- Displays Serieal Number.

22 Multi Format LCD Monitor

5. Menu Operations

[7] Display & Set

• Zoom

- Used to magnify the image up to 90% on a

pixel basis and display on full screen.

* See section “7. Other Functions -> [4] Zoom”

for more information.

• Zoom H/V Scroll

- Activated when [Zoom] mode is selected.

- Used to move the enlarged image to the left/

right or Up/Down by controlling with the

Knob.

• DSLR Camera Sel.

- Select the DSLR camera to be used with LVM-

095W-N2. Available models are [CANON

5D/7D], [SONY A77] and [NIKON D7000].

* DSLR cameras’ screen size and aspect ratio of

Live / Record / Playback modes vary

depending to their manufacturer.

• DSLR Camera Scale (HDMI Format Only)).

- This is a special function for CANON/ NIKON/

SONY DSLR cameras.

- Used to scale the image with diff erent

resolution as to the operation mode(Live

View/ Record/ PlayBack) of the camera to fi ll

the full screen.

* See section “7. Other Functions [8] DSLR

Scale” for more information.

• Closed Caption

- This item selects Closed Caption.

- Available modes are OFF, 708, 608(LINE21) and

608(ANC).

* 608 : CEA-608-B, 708 : CEA-708-C standard

display only.

• TimeCode Enable

- Used to set the time code among Off , VITC

and LTC.

• Focus Assist

- Focus Assist helps the shooters to easily fi nd

out the exact area in the picture that is in

focus, simply by adding colors on the

boundaries of the subject in the picture.

- Activates in the order of [Off ] - [Mono On] –

[Color On].

* (Mono) On : The boundary of the area with

good focus is colored with the designated

color, while the rest of the areas(pixels)

receive only Y’(Luma) signals and become

black & white image.

* (Color) On : Only the boundary of the area

with good focus is displayed with the

designated color.

* See section “7. Other Functions [6] Focus

Assist” for more information.

• Focus Assist Color

- Used to select a color for Focus Assist among

red, green and blue.

- This feature is available only when the Focus

Assist mode is activated.

• Focus Assist Level

- Used to set the edge diff erence value

between the edges in an image.

- Available values are from 0 to 100. Larger

value means more sophisticated detail

detection.

- Designated color is displayed when the

diff erence of the edges exceeds the

previously set value.

- This feature is available only when the Focus

Assist mode is activated.

Multi Format LCD Monitor 23

5. Menu Operations

[7] Display & Set

• KeyLed Indication

- Used to control the Key Lamp on the front of

the monitor.

- If the button with LED is pressed with the

KEY LED Off , LED comes on but turns off after

3 seconds later.

• S/W upgrade

- Used to upgrade the fi rmware using USB

(Thumb drive).

* See section “7. Other Functions -> [11]

Firmware Upgrade” for more information.

• S/W upgrade start

- Used to start S/W upgrade. If USB drive is

detected, the fi rmware upgrade becomes

activated.

* See section “7. Other Functions -> [11]

Firmware Upgrade” for more information.

24 Multi Format LCD Monitor

6. Button Functions

[1] SDI Input Button

• LVM-095W-N2 / SRM-095W-N unit is

capable of processing dual SDI Input

signal.

1. Press the[SDI] button on the front of the

monitor and activate the OSD menu as

shown on the below.

2. Input resolution displays on the bottom of

the OSD screen.

3. Press the [SDI] button again to remove the

OSD menu from display.

* If no image displays after selecting the

desired input mode, check and make sure that

your connection is not lose or disconnected.

[2] SOURCE Button

• LVM-095W-N2 / SRM-095W-N unit is

capable of processing Single HDMI and

CVBS Input signal.

1. Press the [SOURCE] button on the front of the

monitor and activate the OSD menu as

shown on the below.

2. Input resolution displays on the bottom of

the OSD screen.

3. Select HDMI or COMPOSITE by pushing Key

button.

* If no image displays after selecting the

desired input mode, check and make sure that

your connection is not lose or disconnected.

Multi Format LCD Monitor 25

6. Button Functions

[3] SCAN Button

• LVM-095W-N2 / SRM-095W-N supports

various scan modes.

1. Press [SCAN] button continuously to activate

various scan modes: OVER SCAN -> Pixel to

Pixel -> User Aspect -> ZERO SCAN

2. The following represents the diff erent types

of scan mode. When a scan mode is

selected, display skips the next mode if its

required condition is not met.

- OVER SCAN : Zooms in/out of the image

to 96% of its original size without changing

the aspect ratio of.

- ZERO SCAN : Zooms in/out of the image

without changing the aspect ratio.

- Pixel to Pixel : 1:1 pixel mapping of original

image. This feature is available only when

the size of the original image is bigger than

the screen size.

[5] Function Key Set Button

• Used to make a quick setting of the

1. Press the function button(F1~F3) on the

front of the monitor for more than 2 seconds

and activate the OSD menu as follows.

2. Move to a desired function with the[UP/

DOWN] button and press the [ENTER]

button to select.

3. Once the function is set, press the Function

button(F1~F3) to activate the function.

[4] ASPECT Button

• LVM-095W-N2 / SRM-095W-N supports

various aspect ratio.

1. Press [ASPECT] button on the front of the

monitor to activate various aspect ratio.

2. Press [ASPECT] button continuously to

activate various aspect ratio: 4:3 -> 2.35:1 ->

1.85:1 -> 15:9 -> 16:10 -> AUTO -> 16:9

26 Multi Format LCD Monitor

7. Other Functions

[1] User Aspect

• Used to adjust the Width /Height display

ratio.

1. Press the [Aspect] button on the front of the

monitor to activate the [USER ASPECT] mode.

2. After the activation, press the [ENTER] button

to begin controlling. Adjust the ratio using

the [UP]/[DOWN] button.

- Adjust the ratio using the [UP]/[DOWN]

button.

- Control range for width : Min. 0~ Max. 1920.

- Control range for height : Min. 0~ Max. 1080.

- The size-adjusted picture always stays in the

center of the screen.

- The size can be adjustable with 2 increment

and decrement.

Multi Format LCD Monitor 27

7. Other Functions

[2] Waveform / Vectorscope

• Waveform Y

- Displays the Luma(Y’) component of the input

signal into waveform.

• Vectorscope

- Displays the color components ‘B-Y’ and

‘R-Y’of the input signals onto the X-Y axis.

- Two diff erent types of Vetorscopes are

displayed according to SD or HD input signals.

- 100% and 75% scales are indicated on the

Vetorscope.

• Waveform Cb, Cr

- Displays the Cb, Cr components of the input

signal into waveform.

100%

75%

• The Waveform/ Vectorscope function can

be used only when the input signal is YUV.

• In the case of RGB input, Waveform RGB is

supported.

• Available modes in the YUV signal:

- Waveform Y

- Vectorscope

- Waveform Wide

- Waveform Y Cb Cr

- Wave_Vector

- Vector_YCbCr

- Full Waveform(Y)

- Full Vectorscope

28 Multi Format LCD Monitor

7. Other Functions

[3] Line Select

(Waveform/Vectorscope)

[4] Zoom

• Used to select specifi c Vertical Line for

Waveform / Vector.

- It is available when the Line Waveform is

activated.

- To activate this feature, go to [Waveform]-

[Waveform/Vector]-[Line Waveform]-

[Select Line Position] and use the [UP]/

[DOWN] button to select a vertical line.

- Selected line is indicated in White on the

screen.

- Control range varies according to the

resolution of the input SDI signal.

* PAL : 0~625

* NTSC : 0~525

* 720p : 0~750

* 1080 i/p : 0~1125

- Control range for HDMI signal varies according

to the output resolution of the signal.

• Used to magnify the input signal from 0%

• Supports Zoom Width Scroll / Zoom

Height Scroll function.

• Zooms IN/OUT focused on the scrolled

area.

- Selected line is indicated on the screen.

Multi Format LCD Monitor 29

7. Other Functions

[5] Luma(Y’) Zone Check

• Color Pattern Type.

- Displays the Luma(Y’) level of the input image

in colors.

- Y’ ≥ 100% : Pixels with higher Y’ level than 100

turn red.

- Y’ ≤ 0% : Pixels with lower Y’ level than 0 turn

green.

- Pixels with Y’ levels designated by the user

are displayed in following colors - yellow,

pink, cyan.

- Factory Default Y’ (Border line between

pink and yellow) level is 75% and pink color

is assigned to pixels with Y’ level from 70% to

75%.

- Yellow color is assigned to pixels with Y’ level

from 75% to 85%, and Cyan from 60% to 70%.

This function is designed for a better

performance in setting the exposure of

lighting when shooting with vDSLR cameras.

• Zebra Pattern Type

- Displays the pixels with designated Luma(Y’)

levels with zebra pattern.

- Y’ ≥ 100%: Pixels with Y’ level over 100% turn

into red diagonal stripes.

- Y’ ≤ 0% : Pixels with Y’ level under 0% turn into

green diagonal stripes.

- User defi ned Y’ levels are displayed as black

diagonal stripes.

- Factory Default Y’ level is 70% and the pixels

with Y’ level from 65% to 75% is displayed with

zebra pattern.

- Pixels with 10% of Y’ level is displayed as black

diagonal stripes.

30 Multi Format LCD Monitor

7. Other Functions

[6] Focus Assist [7] Range Error

• Focus Assist function assigns a color to

the pixels on the boundaries of the image

to inform the user to achieve the

- With this function, user can easily diff erentiate

the focused area from out-focused area

especially when shooting with a shallow

depth of fi eld.

- Available types are [Mono] and [Color] types.

* [Mono] : Background image is mono type.

[Color] : Background image is original color

type.

• Pixels with Y’ or C’ levels exceeding the

designated levels of Y MAX, Y MIN, C MAX

and C MIN shall blink.

- Analyzes the input signal’s Luma(Y’) and

chroma information(C’) and if the

input signal exceeds the designated

minimum value and maximum value, the

pixel shall blink. This function is to help the

user to easily fi nd out any unwanted levels of

signals and for a better exposure setting.

* In the case of RGB input, Range Error is not

supported.

Multi Format LCD Monitor 31

7. Other Functions

[8] DSLR Scale

• This function is designed for some

DSLR cameras(Canon 5D, 550D, SONY A77

and Nikon D7000) that output

diff erent resolution from the operation

mode (preview, recording, playback).

• Select the Camera model in the [Display/

Vide]- [DSLR Camera Sel.] menu.

• CANON

- In StandBy mode of Canon 5D Mark II, 1080i

of HD resolution is indicated. However, the

real output resolution is 1620x1080, so a blank

area is displayed on the screen because the

16:9 aspect ratio is not realized.

- In this case, use the DSLR SCALE function to

enlarge the 1620x1080 image and display full

screen. In Recording mode of CANON 5D

Mark II, the output resolution is SD(480p).

- Although it is SD, the real output resolution is

640x390 not 720x480.

- DSLR SCALE function scales the 640×390

image to 1280x800(panel resolution) and

displays it full screen.

※ Note

1. When you compare the circle chart or the camera shooting chart with DSLR connected monitor(HDMI) and HDMI to SDI Conversion connected monitor, The function of Live/

Rec 16:9 mode should be selected to compare circle and it is equal to its actual ratio. If the circle is compared in Live/Rec Full mode, the output of the circle is deformed.

2. Both LVM-095W-N2 / SRM-095W-N

connected DSLR and LVM-095W-N2 / SRM-

095W-N connected HDMI to SDI Conversion

should be compared to cirlce in Zeroscan

mode. It is deformed if user selects in

Overscan and Underscan mode.

• SONY

- In StandBy/Record mode of SONY, actual

resolution of the output signal from HDMI

terminal is 1440x1080, failing to display 16:9

aspect ratio and making marginal blank area.

Activating DSLR SCALE function will scale the

1440x1080 raster image to fi ll the full screen.

• NIKON

- In StandBy/Record mode of NIKON, actual

resolution of the output signal from HDMI

terminal is 952x634, failing to display 16:9

aspect ratio and making marginal blank area.

Activating DSLR SCALE function will scale the

952x634 raster image to fi ll the full screen.

32 Multi Format LCD Monitor

7. Other Functions

[9] HDMI To SDI Conversion-Out [10] Internal Pattern

• Video source from ‘HDMI input’ terminal

can be output through ‘SDI throughout’

terminal.

※ Note: HDSLR camera manufacturers usually specify the resolution and frame rate for the recording. The signal format that is output through the HDMI terminal of cameras may diff er from maker to maker. The signal format for HDMI output and playback function of

Canon HDSLRs is 59.94i. And even though 60i or 60p is specifi ed in the specifi cation of the cameras, the actual recording or HDMI output format would be 59.94i or 59.94p.

- SDI Input formats are output as below :

Input (HDMI) Output(SDI)

480 59.94i/p

576 50i/p

480i(59.94)(SMPTE-125M)

576i(50) (ITU-R BT656)

• Displays internally generated test

patterns.

- The pattern consists of ColorBar and

Pluge+Grayscale Patterns. Full screen

colors of various gray levels(0~100%) are also

embedded.

- In HDMI Color format, RGB mode is not

available.

Multi Format LCD Monitor 33

7. Other Functions

[11] Firmware Upgrade

• USB memory stick(Thumb drive) that has

F/W is necessary.

• Select Display&Set menu

- Connect USB memory stick to USB slot in

front of the monitor.

- Set [S/W upgrade] as [On].

- If USB memory stick is connected correctly,

[S/W upgrade start] is activated.

* if the item is not activated, please disconnect

and connect the USB memory stick again.

After 5 sec. do the same procedure.

- The monitor searchs USB memory stick. - Select [Yes] in [S/W upgrade start] and

proceed the fi rmware update.

* During the update, the monitor screen is off ,

and nothing functions.

* After the update, TVLogic logo shows up on

the screen, and the monitor initializes.

* Update can take 10~20min. depending on

fi rmware kind.

34 Multi Format LCD Monitor

8. Product Speci fi cations

LCD

Input Connector

Output

Input Signal

Size

Resolution

Pixel Pitch

Color Depth

Viewing Angle

Luminance of white

Contrast Ratio

Display Area

1 X HDMI

1 X BNC

3G-SDI

HD-SDI

SD-SDI

HDMI

LVM-095W-N2

9”

1920 x 1080 (16:9)

0.1035 x 0. 1035 mm

16.7M (Dithered 8bit)

H : 176 degrees / V : 176 degrees

400 cd/ m 2 (Center)

750 : 1

198.72(H) X 111.78(V) mm

HDMI Input

SDI A Channel Input

SDI B Channel Input, CVBS Channel Input (shared)

SDI Channel Output (Active Loop Through)

2.970Gbps

1.485Gbps

270Mbps

1080p (23.98/24/25/30/50/59.94/60)/1080i(50/59.94/60)/720p(50/60)

480i(60)/480p(60)/576i(50)/576p(50) 640x480/720x400/800x600/1024x768/

1280x768/1280x1024/1366x768

1080p (60/59.94/50/30/29.97/25/24/23.98/30sF/29.97sF/25sF/24sF/23.98sF) SMPTE-425M-A/B

SDI Input Signal

Formats

SMPTE-274M

SMPTE-296M

SMPTE-260M

SMPTE-125M

ITU-R BT.656

2K Format

1080p (30/29.97/25/24/24sF/23.98/23.98sF/ 50/59.94/60 )

1080i (60/59.94/50)

720p (60/59.94/50)

1035i (60/59.94)

480i (59.94)

576i (50)

2048 x 1080p (24/24sF/23.98/23.98sF)

Embedded Audio / Analog Stereo (Phone Jack) Audio In

Audio Out

Power

Power Consumption (Approx.)

Operating Temperature

Storage Temperature

Analog Stereo (Phone Jack), Internal speaker (Stereo)

DC 12/24V (XLR-4pin (male) connector)

24 Watts(DC)/Max 2A

0 ℃ to 40 ℃ (32 ℉ to 104 ℉)

-30 °C to 50 °C (-22 °F to 122 °F )

Main Body Dimensions (mm/inch) 223 X 175 X 60 (8.78 X 6.89 X 2.36)

Main Body Dimensions with stand (mm/inch) 260 X 194.2 X 90 (10.24 X 7.65 X 3.54)

Box Dimensions (mm/inch)

Weight

Basic Accessories

Optional Accessories

330 X 250 X 180 (12.99 X 13.78 X 7.09)

2.1kg / 4.63 lbs

DC Power adapter, AC Power Cord, Camera Mount, Handle, Stand

Acylic Protector, Rack Mountable Kit, HDMI Bracket, Camera Mount

Ball Head, Sun-Hood, Carrying Bag With Hood

* The specifi cation above may be changed without notice.

* When using a DC Adapter other than the one supplied by the manufacturer, please be advised that

the adapter with DC 12V/3A ~ 6A can be compatible with the monitor.

Multi Format LCD Monitor 35

8. Product Speci fi cations

SRM-095W-N

LCD

Input Connector

Output

Input Signal

Size

Resolution

Pixel Pitch

Color Depth

Viewing Angle

Luminance of white

Contrast Ratio

Display Area

1 X HDMI

1 X BNC

3G-SDI

HD-SDI

SD-SDI

HDMI

SMPTE-425M-A/B

SMPTE-274M

SDI Input Signal

Formats

SMPTE-296M

SMPTE-260M

SMPTE-125M

ITU-R BT.656

2K Format

Audio In

Audio Out

Power

Power Consumption (Approx.)

Operating Temperature

Storage Temperature

Main Body Dimensions (mm/inch)

9”

1920 x 1080 (16:9)

0.1035 x 0. 1035 mm

16.7M (True 8bit)

H : 176 degrees / V : 176 degrees

800 cd/ m 2 (Center)

750 : 1

198.72(H) X 111.78(V) mm

HDMI Input

SDI A Channel Input

SDI B Channel Input CVBS Channel Input (shared)

SDI Channel Output (Active Loop Through)

2.970Gbps

1.485Gbps

270Mbps

1080p (23.98/24/25/30/50/59.94/60)/1080i(50/59.94/60)/720p(50/60)

480i(60)/480p(60)/576i(50)/576p(50) 640x480/720x400/800x600/1024x768/

1280x768/1280x1024/1366x768

1080p (60/59.94/50/30/29.97/25/24/23.98/30sF/29.97sF/25sF/24sF/23.98sF)

1080p (30/29.97/25/24/24sF/23.98/23.98sF/ 50/59.94/60 )

1080i (60/59.94/50)

720p (60/59.94/50)

1035i (60/59.94)

480i (59.94)

576i (50)

2048 x 1080p (24/24sF/23.98/23.98sF)

Embedded Audio / Analog Stereo (Phone Jack)

Analog Stereo (Phone Jack), Internal speaker (Stereo)

DC 12/24V (XLR-4pin (male) connector)

32 Watts(DC)/Max 2.8A

0 ℃ to 40 ℃ (32 ℉ to 104 ℉)

-30 °C to 50 °C (-22 °F to 122 °F )

223 X 175 X 60 (8.78 X 6.89 X 2.36)

Main Body Dimensions with stand (mm/inch) 260 X 194.2 X 90 (10.24 X 7.65 X 3.54)

Box Dimensions (mm/inch) 330 X 250 X 180 (12.99 X 13.78 X 7.09)

Weight

Basic Accessories

2.1kg / 4.63 lbs

DC Power adapter, AC Power Cord, Camera Mount, Handle, Stand

Optional Accessories

Acylic Protector, Rack Mountable Kit, HDMI Bracket, Camera Mount

Ball Head, Sun-Hood, Carrying Bag With Hood

* The specifi cation above may be changed without notice.

* When using a DC Adapter other than the one supplied by the manufacturer, please be advised that

the adapter with DC 12V/3A ~ 6A can be compatible with the monitor.

36 Multi Format LCD Monitor

9. Optional Accessories

Acrylic Protector

9”

Rack-Mountable Kit

9”

HDMI Bracket

9”

Camera Mount Ball Head

9”

Sun Hood

9”

Carryng Bag with Hood

7”

9”

Multi Format LCD Monitor 37

MEMO

38 Multi Format LCD Monitor

FOR MORE INFORMATION PLEASE VISIT : http://www.tvlogic.tv

12F, ACE HIGH-END TOWER 8, 84, Gasan digital 1-ro, Geumcheon-gu, Seoul, 08590, KOREA

TEL : +82-70-8668-6611, FAX : 82-2-6123-3201, E-mail : [email protected]

Hello! I am an AI chatbot specifically trained to assist you with the TVLogic LVM-095W-N2 SRM-095W-N Operation Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated

Multi Format Broadcast

LCD Monitor

1. Caution

2. Main Features

3. Controls & Functions

4. Menu Tree & Adjustment

5. Menu Operations

[1] Picture

[2] Color

[3] Marker

[4] GPI/UMD

[5] Waveform

[6] Audio

[7] Display & Set

6. Button Functions

7. Other Functions

8. Product Speci

cations

9. Optional Accessories

16

18

21

12

13

14

22

25

27

35

37

04

06

07

11

12

FCC (Federal Communications Commission)

Disposal of Old Electrical & Electronic Equipment

LVM-095W-N2 / SRM-095W-N Monitors contain the following features:

LVM-095W-N2 / SRM-095W-N : FRONT

LVM-095W-N2 / SRM-095W-N : REAR

LVM-095W-N2 / SRM-095W-N : FRONT

LVM-095W-N2 / SRM-095W-N : FRONT

LVM-095W-N2 / SRM-095W-N : REAR

[1] Menu Tree

[3] Menu Control Sequence

[2] Menu Control

[1] Picture

[2] Color

[3] Marker

[3] Marker

[4] GPI / UMD

Menu

Classifi cation

Settable Values

[4] GPI / UMD

[4] GPI / UMD [5] Waveform

[5] Waveform

[5] Waveform

[6] Audio

[7] Display & Set

[7] Display & Set

[7] Display & Set

[1] SDI Input Button

[2] SOURCE Button

[3] SCAN Button

[5] Function Key Set Button

[4] ASPECT Button

[1] User Aspect

[2] Waveform / Vectorscope

[3] Line Select

[4] Zoom

[5] Luma(Y’) Zone Check

[6] Focus Assist [7] Range Error

[8] DSLR Scale

[9] HDMI To SDI Conversion-Out [10] Internal Pattern

[11] Firmware Upgrade

LVM-095W-N2

SRM-095W-N

FOR MORE INFORMATION PLEASE VISIT : http://www.tvlogic.tv

Related