Bestway Flowclear 58367E Owner's Manual
Bestway Flowclear 58367E is a sand filter with a filter diameter of 437mm that provides effective pool water filtration with a filter area of 1.61ft2 (0.150m2 ). It has a maximum operating pressure of 1.58Bar ( 23PSI) and a working pressure of <0.56Mpa ( 8PSI). The filter can handle water temperatures up to 40℃ and requires approximately 35kg of #20 silica sand with a size of 0.45-0.85mm (not included). The sand filter features a 6-function control valve for filter, rinse, circulate, backwash, closed, and drain functions, and has a pressure gauge for monitoring system pressure.
Advertisement
Advertisement
#58367E
110-120V~60Hz, 3.5A
4006936
TO THE STORE
For FAQ, Manuals, Videos Or www.bestway-service.com
FLOWCLEAR
TM
Sand Filter
OWNER’S MANUAL
Email: [email protected]
www.bestway-global.com
www.bestway-service.com
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书 ) JS-YF-2015-B-06507/ 封面
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
2
S-S-004040
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING -
TO REDUCE THE RISK OF INJURY, do not permit children to use this product unless they are closely supervised at all times.
WARNING -
RISK OF ELECTRIC SHOCK - Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of the plug is needed, use only identical replacement parts.
WARNING -
The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a qualified service representative before using.
CAUTION -
To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
WARNING -
To reduce the risk of electric shock, replace damaged cord immediately.
WARNING -
To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION:
This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
•THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
•
CAUTION:
TO ENSURE CONTINUED PROTECTION AGAINST SHOCK HAZARD, USE ONLY IDENTICAL
•
REPLACEMENT PARTS WHEN SERVICING.
WARNING:
POOLS.
RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A GROUNDING TYPE RECEPTACLE.
• CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED
•
CAUTION:
CONNECT ONLY TO GROUNDING TYPE RECEPTACLE PROTECTED BY A CLASS A GROUND
FAULT CIRCUIT INTERRUPTER.
•
CAUTION:
FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC SHOCK THIS UNIT IS TO BE
MOUNTED TO THE BASE IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
•
WARNING -
RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using - Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated - When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
3
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING -
TO REDUCE THE RISK OF INJURY, do not permit children to use this product unless they are closely supervised at all times.
WARNING -
RISK OF ELECTRIC SHOCK - Connect only to a grounding type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of the plug is needed, use only identical replacement parts.
WARNING -
The unit is provided with a ground-fault circuit-interrupter (GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this pump. Disconnect the pump and have the problem corrected by a qualified service representative before using.
CAUTION -
To reduce the risk of electric shock the pool must be installed no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.
WARNING -
To reduce the risk of electric shock, replace damaged cord immediately.
WARNING -
To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly located outlet.
CAUTION:
This pump is for use with storable pools only. Do not use with permanently-installed pools. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify Bestway at the customer service address listed on this manual for any damaged or missing parts at the time of purchase.
•THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
•
CAUTION:
TO ENSURE CONTINUED PROTECTION AGAINST SHOCK HAZARD, USE ONLY IDENTICAL
•
REPLACEMENT PARTS WHEN SERVICING.
WARNING:
POOLS.
RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A GROUNDING TYPE RECEPTACLE.
• CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO NOT USE WITH PERMANENTLY-INSTALLED
•
CAUTION:
CONNECT ONLY TO GROUNDING TYPE RECEPTACLE PROTECTED BY A CLASS A GROUND
FAULT CIRCUIT INTERRUPTER.
•
CAUTION:
FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC SHOCK THIS UNIT IS TO BE
MOUNTED TO THE BASE IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS.
•
WARNING -
RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using - Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated - When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
5
PARTS REFERENCE OVERVIEW
Before asse bling the sand filter, take a few inutes to be o e fa iliar with all the sand filter parts
6
8
7
10
1
2
3
4
9 12
15
12
13
14
11
18
19
16
17
12
26
21
22
REF NO
1
2
11
12
1
14
15
16
17
18
19
20
21
22
4
5
6
7
8
9
10
26
DESCRPITION
Control Valve
Pressure Gauge
Flange Cla p
Hub Cover
Tank
Hub
Pollution Cartridge
Drain Washer
Drain Valve Cap
Tank Base
Garden Hose Adaptor
Washer
Port D Cap
Piping
O-ring
Strainer Cover
Strainer
Filter Cartridge
Seal Ring
Pu p
Adaptor
Hose Cla ps
Hose( 8
Adapter Nut
QTY
SPARE
PART NO
P61204
P611 8
P61205
P61209
P6121
P61206
P61211
P6581
P6580
P61212
P6614
P6029
P6540
P6560
P61214
P6561
P6562
P61210
P656
P61208US
P6916
P6124
P6517
P6615
2
4
2
1
1
1
1
1
1
1
1
8
1
1
1
1
1
1
1
5
2
1
1
1
20
22 27 22
12
22 27 22
29
24
Optional Parts
12
22
24
Washer
Hose Clamps
Debris Screen
Debris Screen
25
27
28
29
T-Joint
Hose (Φ32mm)
O-Ring
GFCI
1
1
2
1
1
2
2
1
P6029
P6124
P6680
P61318
P61408
P6019
P6005
P6783
P6680 P61318
28 25 28
4 7
SPECIFICATIONS
Filter Diameter
Effective Filter Area:
Max. Operating Pressure:
Working sand filter pressure:
Max. Water Temperature:
Sand:
Sand Size:
Sand Capacity:
437mm
1.61ft
2 (0.150m
2 )
1.58Bar(23PSI)
<0.56Mpa( 8PSI)
40 ℃
Not included
#20 silica sand,0.45-0.85mm
Approximately 35kg
6
4
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
CONTROL VALVE OVERVIEW
WARNING:
To prevent equipment damage and possible
A injury, always switch off sand filter before changing the Control Valve function. Changing valve positions while the pump is running can damage the Control Valve, which may cause personal injury or property damage.
How to Use the Control Valve:
Press down on the Control Valve handle and rotate to desired function.
C
CONTROL VALVE FUNCTIONS
D
The Control valve is used to select 6 different filter functions: Filter, Rinse, Circulate, Backwash, Closed and Drain.
Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool.
Circulate: This function circulates pool water bypassing the sand filter; use this function if the filter is broken to collect debris in the Debris Screens.
Backwash: This function is used to clean the sand bed; water is pumped down through the Collector Hub, upwards through the sand bed, and deposited out of Port D.
Rinse: This function for initial startup, cleaning, and sand bed leveling after Backwash; water is pumped downwards through the sand bed, up through the
Collector Hub and deposited out of the valve Port D.
Drain: This function drains water from the pool; another filter bypass setting, water is pumped and deposited out of Port D, instead of returning it to the pool.
Closed: This function stops water flowing between the sand filter and the pool.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф 3.2cm)
1. Connect the Adaptors (21) to the Hose .
2. Place the loose Hose Clamps (22) in the end of Hose
with Adaptor (21).
1 in h<
21
>1/2 in
A
>1/2 in
B
22
P61318 P6680
3. Attach the Hoses to the corresponding letters on the pool.
4. Attach the Hoses to the sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position; ensure the corresponding letters on both the pool and the sand filter match (A to A, B to B).
5. Remove the Stopper Plugs from the pool’s inlet and outlet valves and insert with the Debris Screens (24).
6. With the Hoses and Debris Screens (24) in position, tighten the Hose Clamps (22).
GARDEN HOSE ADAPTOR FUNCTIONS
1
2
5
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
3
S-S-004040
1. Assemble the garden hose adaptor.
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor .
NOTE:
1. Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
GFCI Test
A.
To test the GFCI plug, insert it into a grounding type
receptacle.
B. Press the “RESET” button; the indicator turns red.
NOTE:
If the indicator light is not on, the test has failed.
C.
Press the “TEST” button. The indicator turns off.
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales
Service.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground
or a certain pedestal made of wood or concrete before use to prevent the sand filter
from accidentally falling. Fully assembled sand filter will exceed 35kg. The mounting holes should be 8mm in diameter and
spaced 86mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE:
Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one 35kg bag should suffic If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the
Skimmer on the Hub.
NOTE:
SAND NOT INCLUDED.
1. Place the tank base in the right place, aligning the position hole.
2. Place the tank onto the right place of tank base.
3 .Place the filter cover(4).
4. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. #20 Silica sand 0.45-0.85mm, approximately 35 kg.
5. Pull out the filter cover (4).
6. Lower the control valve over the tank slowly,and ensure the bypass pipe protruding underneath the control valve fits securely into the hub (6).
7. Make sure Port C on the Control Valve is align Port C on the Pump. Attach the Top Flange Clamp (3) and screw into position.
8. Attach the Piping (14) to Pump Port C and to Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping (14).
Section II: Hose Configuration for Backwashing and Rinsing
NOTE:
Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water, make certain all of the pool’s Debris Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E).
If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A (see Fig.A-1)
1. Attach one end of the hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect both ends of hoses (Φ32mm) to the pool valves marked “B”, place the loose Hose Clamps (P6124) on the end of
Hoses. Connect both free ends of hoses (Φ32mm) to the T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose (23) to the T-joint (25), screw the threaded locking ring into position.
4. Remove the Stopper Plugs from the pool’ s outlet valves (marked “B”) and insert with the Debris Screens. With the Hoses and Debris Screens in position, tighten the Hose Clamps.
Method B (see Fig.B-1)
1. Attach one Hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded locking ring into position.
3. Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Screw the other Hose (23) to Port D and place the opposite end in drain area.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION:
DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device, and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
NOTE:
It is imperative to check that the hydraulic connectors are not obturated.
NOTE:
Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1.Detach the Hose (23) from Port D.
2.Attach the Hose (23 )to the Control Valve’s Port A ; screw the threaded locking ring into position.
3.Connect the other end of Hose (23) to the pool’s Inlet A.
4.Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE:
To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE:
The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.56Bar (8.0PSI) when it is running.
Sand Filter Maintenance
CAUTION:
You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure Gauge is 0.56Bar (8.0PSI) or higher, or water flow to the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section II and Section III:
Backwash and Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used.
Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE:
The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING:
DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф 3.2cm)
1. Connect the Adaptors (21) to the Hose .
2. Place the loose Hose Clamps (22) in the end of Hose
with Adaptor (21).
3. Attach the Hoses to the corresponding letters on the pool.
4. Attach the Hoses to the sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position; ensure the corresponding letters on both the pool and the sand filter match (A to A, B to B).
5. Remove the Stopper Plugs from the pool’s inlet and outlet valves and insert with the Debris Screens (24).
6. With the Hoses and Debris Screens (24) in position, tighten the Hose Clamps (22).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor.
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor .
NOTE:
1. Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
GFCI Test
A.
To test the GFCI plug, insert it into a grounding type
receptacle.
B. Press the “RESET” button; the indicator turns red.
NOTE:
If the indicator light is not on, the test has failed.
C.
Press the “TEST” button. The indicator turns off.
A
RESET
TEST
B
RESET
TEST
C
RESET
TEST
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales
Service.
D
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
86mm
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground
or a certain pedestal made of wood or concrete before use to prevent the sand filter
Ф8mm
from accidentally falling. Fully assembled sand filter will exceed 35kg. The mounting holes should be 8mm in diameter and
spaced 86mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE:
Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one 35kg bag should suffic If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the
Skimmer on the Hub.
NOTE:
SAND NOT INCLUDED.
1. Place the tank base in the right place, aligning the position hole.
2. Place the tank onto the right place of tank base.
3 .Place the filter cover(4).
4. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. #20 Silica sand 0.45-0.85mm, approximately 35 kg.
San d
4
20
MAX
MIN
4
10
MAX
MIN
1 2 3 4
6
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
5. Pull out the filter cover (4).
6. Lower the control valve over the tank slowly,and ensure the bypass pipe protruding underneath the control valve fits securely into the hub (6).
7. Make sure Port C on the Control Valve is align Port C on the Pump. Attach the Top Flange Clamp (3) and screw into position.
8. Attach the Piping (14) to Pump Port C and to Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping (14).
Section II: Hose Configuration for Backwashing and Rinsing
NOTE:
Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water, make certain all of the pool’s Debris Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E).
If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A (see Fig.A-1)
1. Attach one end of the hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect both ends of hoses (Φ32mm) to the pool valves marked “B”, place the loose Hose Clamps (P6124) on the end of
Hoses. Connect both free ends of hoses (Φ32mm) to the T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose (23) to the T-joint (25), screw the threaded locking ring into position.
4. Remove the Stopper Plugs from the pool’ s outlet valves (marked “B”) and insert with the Debris Screens. With the Hoses and Debris Screens in position, tighten the Hose Clamps.
Method B (see Fig.B-1)
1. Attach one Hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded locking ring into position.
3. Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Screw the other Hose (23) to Port D and place the opposite end in drain area.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION:
DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device, and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
NOTE:
It is imperative to check that the hydraulic connectors are not obturated.
NOTE:
Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1.Detach the Hose (23) from Port D.
2.Attach the Hose (23 )to the Control Valve’s Port A ; screw the threaded locking ring into position.
3.Connect the other end of Hose (23) to the pool’s Inlet A.
4.Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE:
To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE:
The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.56Bar (8.0PSI) when it is running.
Sand Filter Maintenance
CAUTION:
You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure Gauge is 0.56Bar (8.0PSI) or higher, or water flow to the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section II and Section III:
Backwash and Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used.
Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE:
The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING:
DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф 3.2cm)
1. Connect the Adaptors (21) to the Hose .
2. Place the loose Hose Clamps (22) in the end of Hose
with Adaptor (21).
3. Attach the Hoses to the corresponding letters on the pool.
4. Attach the Hoses to the sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position; ensure the corresponding letters on both the pool and the sand filter match (A to A, B to B).
5. Remove the Stopper Plugs from the pool’s inlet and outlet valves and insert with the Debris Screens (24).
6. With the Hoses and Debris Screens (24) in position, tighten the Hose Clamps (22).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor.
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor .
NOTE:
1. Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
GFCI Test
A.
To test the GFCI plug, insert it into a grounding type
receptacle.
B. Press the “RESET” button; the indicator turns red.
NOTE:
If the indicator light is not on, the test has failed.
C.
Press the “TEST” button. The indicator turns off.
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales
Service.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground
or a certain pedestal made of wood or concrete before use to prevent the sand filter
from accidentally falling. Fully assembled sand filter will exceed 35kg. The mounting holes should be 8mm in diameter and
spaced 86mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE:
Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one 35kg bag should suffic If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the
Skimmer on the Hub.
NOTE:
SAND NOT INCLUDED.
1. Place the tank base in the right place, aligning the position hole.
2. Place the tank onto the right place of tank base.
3 .Place the filter cover(4).
4. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. #20 Silica sand 0.45-0.85mm, approximately 35 kg.
5. Pull out the filter cover (4).
6. Lower the control valve over the tank slowly,and ensure the bypass pipe protruding underneath the control valve fits securely into the hub (6).
7. Make sure Port C on the Control Valve is align Port C on the Pump. Attach the Top Flange Clamp (3) and screw into position.
8. Attach the Piping (14) to Pump Port C and to Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping (14).
C
4 14
6
3
C
5 6 7 8
Section II: Hose Configuration for Backwashing and Rinsing
NOTE:
Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water, make certain all of the pool’s Debris Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E).
If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A (see Fig.A-1)
1. Attach one end of the hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect both ends of hoses (Φ32mm) to the pool valves marked “B”, place the loose Hose Clamps (P6124) on the end of
Hoses. Connect both free ends of hoses (Φ32mm) to the T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose (23) to the T-joint (25), screw the threaded locking ring into position.
4. Remove the Stopper Plugs from the pool’ s outlet valves (marked “B”) and insert with the Debris Screens. With the Hoses and Debris Screens in position, tighten the Hose Clamps.
Method B (see Fig.B-1)
1. Attach one Hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded locking ring into position.
3. Open the connection valve.
Water level
B B >1.2 inch
>1/2 in B
P6124
A Liner
25
P61408
P6680
A
B
D
D
Fig.E
Fig.A-1
23 (1m)
Fig.
B-1
23
B
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Screw the other Hose (23) to Port D and place the opposite end in drain area.
B
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION:
DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device, and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
7
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
NOTE:
It is imperative to check that the hydraulic connectors are not obturated.
NOTE:
Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1.Detach the Hose (23) from Port D.
2.Attach the Hose (23 )to the Control Valve’s Port A ; screw the threaded locking ring into position.
3.Connect the other end of Hose (23) to the pool’s Inlet A.
4.Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE:
To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE:
The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.56Bar (8.0PSI) when it is running.
Sand Filter Maintenance
CAUTION:
You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure Gauge is 0.56Bar (8.0PSI) or higher, or water flow to the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section II and Section III:
Backwash and Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used.
Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE:
The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING:
DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф 3.2cm)
1. Connect the Adaptors (21) to the Hose .
2. Place the loose Hose Clamps (22) in the end of Hose
with Adaptor (21).
3. Attach the Hoses to the corresponding letters on the pool.
4. Attach the Hoses to the sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position; ensure the corresponding letters on both the pool and the sand filter match (A to A, B to B).
5. Remove the Stopper Plugs from the pool’s inlet and outlet valves and insert with the Debris Screens (24).
6. With the Hoses and Debris Screens (24) in position, tighten the Hose Clamps (22).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor.
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor .
NOTE:
1. Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
GFCI Test
A.
To test the GFCI plug, insert it into a grounding type
receptacle.
B. Press the “RESET” button; the indicator turns red.
NOTE:
If the indicator light is not on, the test has failed.
C.
Press the “TEST” button. The indicator turns off.
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales
Service.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground
or a certain pedestal made of wood or concrete before use to prevent the sand filter
from accidentally falling. Fully assembled sand filter will exceed 35kg. The mounting holes should be 8mm in diameter and
spaced 86mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE:
Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one 35kg bag should suffic If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the
Skimmer on the Hub.
NOTE:
SAND NOT INCLUDED.
1. Place the tank base in the right place, aligning the position hole.
2. Place the tank onto the right place of tank base.
3 .Place the filter cover(4).
4. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. #20 Silica sand 0.45-0.85mm, approximately 35 kg.
5. Pull out the filter cover (4).
6. Lower the control valve over the tank slowly,and ensure the bypass pipe protruding underneath the control valve fits securely into the hub (6).
7. Make sure Port C on the Control Valve is align Port C on the Pump. Attach the Top Flange Clamp (3) and screw into position.
8. Attach the Piping (14) to Pump Port C and to Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping (14).
Section II: Hose Configuration for Backwashing and Rinsing
NOTE:
Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water, make certain all of the pool’s Debris Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E).
If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A (see Fig.A-1)
1. Attach one end of the hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect both ends of hoses (Φ32mm) to the pool valves marked “B”, place the loose Hose Clamps (P6124) on the end of
Hoses. Connect both free ends of hoses (Φ32mm) to the T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose (23) to the T-joint (25), screw the threaded locking ring into position.
4. Remove the Stopper Plugs from the pool’ s outlet valves (marked “B”) and insert with the Debris Screens. With the Hoses and Debris Screens in position, tighten the Hose Clamps.
Method B (see Fig.B-1)
1. Attach one Hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded locking ring into position.
3. Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Screw the other Hose (23) to Port D and place the opposite end in drain area.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION:
DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device, and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
NOTE:
It is imperative to check that the hydraulic connectors are not obturated.
NOTE:
Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1.Detach the Hose (23) from Port D.
2.Attach the Hose (23 )to the Control Valve’s Port A ; screw the threaded locking ring into position.
3.Connect the other end of Hose (23) to the pool’s Inlet A.
4.Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Water level
B B
>1.2 inch
A
23(1.5m)
A
B
Liner
A
23
B
23 (1m)
Fig.A-2
B
23
Fig.B-2
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE:
To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE:
The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.56Bar (8.0PSI) when it is running.
Sand Filter Maintenance
CAUTION:
You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure Gauge is 0.56Bar (8.0PSI) or higher, or water flow to the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section II and Section III:
Backwash and Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used.
Do not clean the sand too frequently.
4
0.
0. 6
10
0. 8
15
5
0
0 psi bar
1
23
20
1.
6
1.
2
4
0.
0. 6
10
0. 8
15
5
0
0 psi bar
1
23
20
1.
6
1.
2
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
8
S-S-004040
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE:
The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING:
DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water where it will cause flooding or damage.
• When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
HOSE ADAPTOR FUNCTIONS
Pool with Valves (Ф 3.2cm)
1. Connect the Adaptors (21) to the Hose .
2. Place the loose Hose Clamps (22) in the end of Hose
with Adaptor (21).
3. Attach the Hoses to the corresponding letters on the pool.
4. Attach the Hoses to the sand filter by pressing the hose fitting on the pump port. Screw the threaded locking rings into position; ensure the corresponding letters on both the pool and the sand filter match (A to A, B to B).
5. Remove the Stopper Plugs from the pool’s inlet and outlet valves and insert with the Debris Screens (24).
6. With the Hoses and Debris Screens (24) in position, tighten the Hose Clamps (22).
GARDEN HOSE ADAPTOR FUNCTIONS
1. Assemble the garden hose adaptor.
2. Screw the garden hose adaptor onto port D of the sand filter.
3. Attach garden hose to the garden hose adaptor .
NOTE:
1. Garden hose adaptor can be used for draining your pool and can only be assembled to port D of the sand filter.
2. Always switch off and unplug the sand filter before assembling the garden hose adaptor, and set the control valve to Closed position.
3. Ensure the washer is in position before assembling the garden hose adaptor.
GFCI Test
A.
To test the GFCI plug, insert it into a grounding type
receptacle.
B. Press the “RESET” button; the indicator turns red.
NOTE:
If the indicator light is not on, the test has failed.
C.
Press the “TEST” button. The indicator turns off.
NOTE:
If the indicator light is not off, the test has failed.
D. Press the “RESET” button, the indicator light turns red, and the sand filter is ready for use.
WARNING:
RISK OF ELECTRIC SHOCK. THE GFCI MUST BE TESTED BEFORE EACH USE.
WARNING:
DO NOT USE THE PUMP IF THE ABOVE TEST FAILS. Please contact your local Bestway Aftersales
Service.
Section I: Assembly (You will need a Phillips screwdriver).
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. EN60335-2-41 TEST standard requires the sand filter to be vertically fixed on ground
or a certain pedestal made of wood or concrete before use to prevent the sand filter
from accidentally falling. Fully assembled sand filter will exceed 35kg. The mounting holes should be 8mm in diameter and
spaced 86mm apart. Use two bolts and nuts with a maximum of 8mm in diameter to fasten the sand filter to the pedestal.
Load pool-grade filter sand.
NOTE:
Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85mm, approximately one 35kg bag should suffic If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may damaged, there by voiding the warranty.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the
Skimmer on the Hub.
NOTE:
SAND NOT INCLUDED.
1. Place the tank base in the right place, aligning the position hole.
2. Place the tank onto the right place of tank base.
3 .Place the filter cover(4).
4. Slowly add the sand so the weight of the sand does not damage the Skimmer on the Hub, until it reaches between the marked “MAX” and “MIN”. #20 Silica sand 0.45-0.85mm, approximately 35 kg.
5. Pull out the filter cover (4).
6. Lower the control valve over the tank slowly,and ensure the bypass pipe protruding underneath the control valve fits securely into the hub (6).
7. Make sure Port C on the Control Valve is align Port C on the Pump. Attach the Top Flange Clamp (3) and screw into position.
8. Attach the Piping (14) to Pump Port C and to Control Valve Port C, screw the threaded locking rings into position. Make sure the Washer is properly positioned on both ends of the Piping (14).
Section II: Hose Configuration for Backwashing and Rinsing
NOTE:
Ensure the Control Valve is set to the Closed function.
Your pool should be filled with water, make certain all of the pool’s Debris Screens (24) are fully submerged in water.
Please check if your product includes a T-Joint (25) (see Fig. E).
If yes, assemble your sand filter referring to method A; if no, assemble your sand filter referring to method B.
Method A (see Fig.A-1)
1. Attach one end of the hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Connect both ends of hoses (Φ32mm) to the pool valves marked “B”, place the loose Hose Clamps (P6124) on the end of
Hoses. Connect both free ends of hoses (Φ32mm) to the T-joint (P61408) by tightening the Hose Clamps.
3. Screw the other end of the hose (23) to the T-joint (25), screw the threaded locking ring into position.
4. Remove the Stopper Plugs from the pool’ s outlet valves (marked “B”) and insert with the Debris Screens. With the Hoses and Debris Screens in position, tighten the Hose Clamps.
Method B (see Fig.B-1)
1. Attach one Hose (23) to the sand filter’s Port B; screw the threaded locking ring into position.
2. Screw the other end of the Hose (23) to Port B connection valve; screw the threaded locking ring into position.
3. Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Screw the other Hose (23) to Port D and place the opposite end in drain area.
Section III: Backwash and Rinsing
Backwash and Rinsing must be preformed to prepare the pump for its first use and to wash the sand.
CAUTION:
DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Insert the plug into a residual current device, and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water.
IMPORTANT:
This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water levels near the pool’s Inlet and Outlet valves.
DO NOT DRY RUN THE SAND FILTER.
Section IV: Complete Sand Filter Installation
Connect the Second Hose
NOTE:
It is imperative to check that the hydraulic connectors are not obturated.
NOTE:
Ensure the Control Valve is set to the Closed function.
Assemble your product referring to Fig. A-2 if there is a T-joint (Fig. E), and referring to B-2 if not. The assembly methods are the same.
1.Detach the Hose (23) from Port D.
2.Attach the Hose (23 )to the Control Valve’s Port A ; screw the threaded locking ring into position.
3.Connect the other end of Hose (23) to the pool’s Inlet A.
4.Open the connection valve.
NOTE:
You can refer to pool manual for connection valve’s installation instructions.
Section V: Sand Filter Operation
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE:
To prevent the risk of electrical shock dry any excess water from yourself and the sand filter.
2. Switch on the sand filter to run it.
NOTE:
The sand filter has now started its filtering cycle. Check that water is returning to the pool and take note of the filter pressure on Pressure Gauge. Generally, the recommended sand filter pressure is less than 0.56Bar (8.0PSI) when it is running.
Sand Filter Maintenance
CAUTION:
You must ensure the sand filter is switched off and unplugged before any maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will increase. When the Pressure Gauge is 0.56Bar (8.0PSI) or higher, or water flow to the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in Section II and Section III:
Backwash and Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for precision measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how often the pool is used.
Do not clean the sand too frequently.
Cleaning the Strainer
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE:
The Strainer must be emptied and cleaned periodically.
A dirty or blocked strainer will reduce the performance of the sand filter.
Lowering or Draining Pool Water
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING:
DO NOT DRY RUN THE SAND FILTER.
Winterizing
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter as previously outlined in Section II and Section III.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
TROUBLESHOOTING
Problems
Sand Filter does not operate
Probable Causes
- GFCI broken
Sand is flowing to the pool
- Sand is too small
- Move the control valve from the backwash to the
filter function without stopping the sand filter
- The level of the sand is too high
- The skimmer is broken
Solutions
- Contact your local Bestway Aftersales Service point to get instructions
- Recommend 0.45mm to 0.85mm #20 silica sand
- Stop the sand filter every time set the control valve
- Check if the level of the sand is between the marked “MAX” and “ MIN” on the
collector hub
- Replace the skimmer
No water flow
Excessive filter pressure
- Stopper plugs are not removed
- Air was not released
- The control valve is set to Closed
- The strainer is blocked
- Sand filter broken
- Dirty filter
- Calcified sand bed
- Insufficient backwashing
- The pressure gauge is broken
- Remove the stopper plugs and insert the debris screens
- Release the air
- Set to filter function
- Clean the strainer
- Call for service
- Backwash
- Inspect sand and change if necessary
- Backwash until water runs clear
- Replace the pressure gauge
Control Valve leaks from the port D
- Control Valve is set between two functions
- The gasket is broken
- Set to one function
- Replace the gasket
Connectors leak
- Washer of the connectors not in place
- Washer of the connectors broken
- O-ring on the hose connection is broken
- Loose Hoses
- Reposition the washer
- Replace the washer
- Replace the o-ring
- Tighten them
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
9
S-S-004040
Limited BESTWAY
®
Manufacturer’s Warranty
The product you have purchased comes with a limited warranty. Bestway ® stands behind our quality guarantee and assures, through a replacement warranty, your product will be free from manufacturer’s defects that result in leaks. If a Manufacturer defect is found within:360 days for the motor pumps from the original date of purchase for 30 days for hoses, fitting and accessories included in the package from the original data of purchase.
To enact a warranty claim, this form must be completed and supplied with a copy of your purchase receipt to your local Bestway After Sales Center.
Please contact your local Bestway After Sales Center before sending any documents, they will provide full instructions of what is needed for your claim.
Bestway ® is not responsible for economic loss due to water or chemical costs and Bestway ® will not replace any products deemed to have been damaged due to negligence or having been used outside of the owner’s manual guidelines.
Bestway’s warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within the user manual, this
parties. The product must be stored and handled in accordance with the warranty applies only to products which have not been modified by any 3 rd technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of incorrect voltage, excessive heat exposure, improper installation, improper wiring or testing, or improper storage.
Replacements and repairs don’t extend the duration of the warranty. The date to be considered as the start of the warranty is only the one shown in the original receipt/purchase invoice.
Please copy the Batch Number located on the body of the sand filter.
YY/M
M/DD
Batch
Number
Batch
Number
Batch
Number
Batch Number:
TO: BESTWAY ® SERVICE DEPARTMENT DATE:
Date of purchase receipt:
Customer Code Number:
FAX/E-MAIL/TEL: Please refer to your country according to the information you find on the back cover or on our website: www.bestway-service.com
Please provide your address details in full. Note: Incomplete address details will result in delayed shipments.
Bestway reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
REQUIRED INFORMATION -- PLEASE WRITE THE DELIVERY ADDRESS
Name: Address:
Country:
Telephone:
Retailer:
City:
Fax:
Please Clearly Write Your Item Code:
Zip code:
Mobile:
E-mail:
Item Code
Batch
Number
SAND FILTER MODEL #XXXXXX
SAND FILTER WITH OZONATOR MODEL #XXXXXX
All drawings for illustration purpose only. Not to scale.
Description of problem
Water leaking
Stopped working
Item is incomplete, Which part is missing – Please put the code you find on the instruction manual
Others, please describe
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
Bestway reserves the right to request photographic evidence of defective parts, or to require the sending of the item for additional testing.
In order to best assist you, we request all information you provide is complete.
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE WWW.BESTWAY-SERVICE.COM.
VIDEOS ARE ALSO AVAILABLE ON OUR BESTWAY CHANNEL ON YOU TUBE: http://youtube.com/user/BestwayService.
10
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
11
S-S-004040
Authorized Service Centers
Albania
Phone: (+355) 682003429
Fax: (+386) 056621203
E-mail: [email protected]
Argentina
Phone: (+54) 1159843871
E-mail: [email protected]
Australia
Phone: (+61) 290371388
Fax: (+61) 297379423
E-mail: [email protected]
Austria
Phone: (+43) 720882434
Fax: (+43) 720882435
E-mail: [email protected]
Belgium
Phone: 0 800 20 132
Fax: (+32) 026104411
E-mail: [email protected]
Bosnia
Phone: (+387) 039670935
Fax: (+386) 056621203
E-mail: [email protected]
Brasil
Phone: 0800 001 8400
E-mail: [email protected]
Bulgaria
Phone: (+359) 879012892
Fax: (+359) 29250232
E-mail: [email protected]
Canada
Phone: 1 855 838 3888
Fax: 1 480 838 1888
E-mail: [email protected]
Chile
Phone: (+56) 2232036438
E-mail: [email protected]
Colombia
Phone: (+57) 13441717
E-mail: [email protected]
Croatia
Phone: (+385) 0997930168
Fax: (+386) 056621203
E-mail: [email protected]
Cyprus
Phone: (+357) 22 426803
(+357) 22 423824
Fax: (+357) 22 495137
E-mail: [email protected]
Czech Republic
Phone: (+420) 0387020573
E-mail: [email protected]
Denmark
Phone: (+45) 33321019
Fax: (+45) 33321036
E-mail: [email protected]
Finland
Phone: (+358) 504104403
E-mail: [email protected]
France
Phone: 0892707709 (0,34 TTC/MINUTE)
Fax: (+33) 0489069991
E-mail: [email protected]
Germany
Phone: (+49) 6946001281
Fax: (+49) 6946001282
E-mail: [email protected]
Greece
Phone: 00.800.391.275.300
Fax: (+39) 0291390361
E-mail: [email protected]
Hungary
Phone: (+36) 0640204624
E-mail: [email protected]
Iceland
Phone: (+46) 8 506 691 90
Fax: (+46) 506 690 99
E-mail: [email protected]
Ireland
Phone: 8006120457
Fax: (+44) 01626835736
E-mail: [email protected]
Italy
Phone: (+39) 0236265839
Fax: (+39) 0291390361
E-mail: [email protected]
Macedonia
Phone: (+389) 032386235
Fax: (+386) 056621203
E-mail: [email protected]
Malta
Phone: (+356) 27438201/21499101
Fax: (+356) 21496206
E-mail: [email protected]
Mexico
Phone: (+52) 5541693920
Fax: (+52) 8183463416
E-mail: [email protected]
Moldova
Phone: (+373) 68535552
E-mail: [email protected]
Netherlands
Phone: 8002378929
Fax: (+31) 887878969
E-mail: [email protected]
New Zealand
Phone: 0800 142 101
E-mail: [email protected]
Norway
Phone: (+47) 22650122
Fax: (+47) 22721127
E-mail: [email protected]
Peru
Phone: (+51) 17089795
E-mail: [email protected]
Poland
Phone: (+48) 327505320 / 322326040
Fax: (+48) 327505330
E-mail: [email protected]
Portugal
Phone: (+351) 707506692
Fax: (+34) 902602705
E-mail: [email protected]
Romania
Phone: (+40) 212525354 / 213362858
Fax: (+40) 212525353 / 213362854
E-mail: [email protected]
Russia ( Россия )
Phone: +7 (495) 978-90-88
E-mail: [email protected]
Serbia and Montenegro
Phone: (+381) 0656644962
(+386) 056621206
Fax: (+386) 056621203
E-mail: [email protected]
Slovak Republic
Phone: (+421) 0415078833
Fax: (+421) 0415078808
E-mail: [email protected]
Slovenia
Phone: (+386) 056621206
Fax: (+386) 056621203
E-mail: [email protected]
South Africa
Phone: (+27)-21-5771401
Toll-Free ： 0800 224 881
Fax: (+27)-21-5774400
E-mail: [email protected]
Spain
Phone: (+34) 902351045
Fax: (+34) 902602705
E-mail: [email protected]
Sweden
Phone: (+46) 8 506 691 90
Fax: (+46) 506 690 99
E-mail: [email protected]
Switzerland
Phone: (+41)(0)719290000
Fax: (+41)(0)719290090
E-mail: [email protected]
Turkey
Phone: (+90) 02126444600
Fax: (+90) 02125550224
E-mail: [email protected] [email protected]
Ukraine
Phone: (+38) 0577597227
(+38) 0677033206
E-mail: [email protected]
United Kingdom
Phone: 08455760116
Fax: (+44) 01626835736
E-mail: [email protected]
USA
Phone: 1 855 838 3888
Fax: 1 480 838 1888
E-mail: [email protected]
S-S-004040
S-S-004040/21.0x28.5cm (#58367E 2000gal 美国规砂滤器说明书) JS-YF-2015-B-06507
Advertisement