Section-5 Air Brakes - Pennsylvania Department of Transportation

Section-5 Air Brakes - Pennsylvania Department of Transportation
Commercial Driver’s License Manual
SECTION 5
aIR bRaKes
tHIs sectIon Is foR dRIveRs WHo dRIve
veHIcles WItH aIR bRaKes
Section-5 Air Brakes
sectIon 5 - aIR bRaKes
Commercial Driver’s License Manual
this section covers
•
•
•
•
air brake system Parts
dual air brake systems
Inspecting air brakes
Using air brakes
this section tells you about air brakes. If you want to drive a truck or bus with air brakes, or pull a trailer with air brakes,
you need to read this section. If you want to pull a trailer with air brakes, you also need to read Section 6, combination
vehicles. You will need the air brake restriction removed from your license if your vehicle needs a cdL and is air brake
equipped.
Air brakes use compressed air to make the brakes work. Air brakes are a good and safe way of stopping large and heavy
vehicles, but the brakes must be well maintained and used properly.
Air brakes are really three different braking systems, service brake, parking brake, and emergency brake:
• the service brake system applies and releases the brakes when you use the brake pedal during normal driving.
• the parking brake system applies and releases the parking brakes when you use the parking brake control.
• the emergency brake system uses parts of the service and parking brake systems to stop the vehicle in a brake
system failure.
the parts of these systems are discussed in greater detail below.
5.1 – aIR bRaKe sYstem PaRts
there are many parts to an air brake system. You should know about the parts discussed here.
5.1.1 – Air Compressor
the air compressor pumps air into the air storage tanks (reservoirs). the air compressor is connected to the engine
through gears or a v-belt. the compressor may be air cooled or may be cooled by the engine cooling system. It may have
its own oil supply or be lubricated by engine oil. If the compressor has its own oil supply, check the oil level before driving.
5.1.2 – Air Compressor Governor
the governor controls when the air compressor will pump air into the air storage tanks. When air tank pressure rises to
the "cut-out" level (around 125 pounds per-square-inch or "psi"), the governor stops the compressor from pumping air.
When the tank pressure falls to the "cut-in" pressure (around 100 psi), the governor allows the compressor to start
pumping again.
5.1.3 – Air Storage Tanks
Air storage tanks are used to hold compressed air. the number and size of air tanks varies among vehicles. the tanks will
hold enough air to allow the brakes to be used several times, even if the compressor stops working.
5.1.4 – Air Tank Drains
compressed air usually has some water and some compressor oil in it, which is bad for the air brake system. For
example, the water can freeze in cold weather and cause brake failure. the water and oil tend to collect in the bottom
of the air tank. Be sure that you drain the air tanks completely. Each air tank is equipped with a drain valve in the bottom.
there are two types:
• manually operated by turning a quarter turn or by pulling a cable. You must drain the tanks yourself at the end
of each day of driving. See Figure 5.1.
• Automatic--the water and oil are automatically expelled. these tanks may be equipped for manual draining as well.
Automatic air tanks are available with electric heating devices. these help prevent freezing of the automatic drain
in cold weather
Section-5 Air Brakes
5-1
5.1.5 – Alcohol Evaporator
Some air brake systems have an alcohol evaporator
to put alcohol into the air system. this helps to reduce
the risk of ice in air brake valves and other parts
during cold weather. Ice inside the system can make
the brakes fail.
Commercial Driver’s License Manual
figure 5.1
check the alcohol container and fill up as necessary,
every day during cold weather. daily air tank drainage
is still needed to get rid of water and oil. (unless the
system has automatic drain valves.)
5.1.6 – Safety Valve
A safety relief valve is installed in the first tank the air
compressor pumps air to. the safety valve protects
the tank and the rest of the system from too much
pressure. the valve is usually set to open at 150 psi.
If the safety valve releases air, something is wrong.
Have the fault fixed by a mechanic.
5.1.7 – The Brake Pedal
You put on the brakes by pushing down the brake pedal. (It is also called the foot valve or treadle valve.) Pushing the
pedal down harder applies more air pressure. Letting up on the brake pedal reduces the air pressure and releases the
brakes. releasing the brakes lets some compressed air go out of the system, so the air pressure in the tanks is reduced.
It must be made up by the air compressor. Pressing and releasing the pedal unnecessarily can let air out faster than the
compressor can replace it. If the pressure gets too low, the brakes will not work.
5.1.8 – Foundation Brakes
Foundation brakes are used at each wheel. the most
common type is the s-cam drum brake. the parts of
the brake are discussed below.
brake drums, shoes, and linings. Brake drums
are located on each end of the vehicle’s axles. the
wheels are bolted to the drums. the braking
mechanism is inside the drum. to stop, the brake
shoes and linings are pushed against the inside of the
drum. this causes friction, which slows the vehicle
(and creates heat). the heat a drum can take without
damage depends on how hard and how long the
brakes are used. too much heat can make the brakes
stop working.
figure 5.2
s-cam brakes. When you push the brake pedal, air
is let into each brake chamber. Air pressure pushes
the rod out, moving the slack adjuster, (an adjustable
device used to compensate for brake shoe wear) thus
twisting the brake camshaft. this turns the s-cam
(so called because it is shaped like the letter "S"). the
s-cam forces the brake shoes away from one another
and presses them against the inside of the brake
drum. When you release the brake pedal, the s-cam
rotates back and a spring pulls the brake shoes away
from the drum, letting the wheels roll freely again.
See Figure 5.2.
Wedge brakes. In this type of brake, the brake chamber push rod pushes a wedge directly between the ends of two
brake shoes. this shoves them apart and against the inside of the brake drum. Wedge brakes may have a single brake
chamber, or two brake chambers, pushing wedges in at both ends of the brake shoes. Wedge type brakes may be
self-adjusting or may require manual adjustment.
5-2
Section-5 Air Brakes
Commercial Driver’s License Manual
disc brakes. In air-operated disc brakes, air pressure acts on a brake chamber and slack adjuster, like s-cam brakes. But
instead of the s-cam, a "power screw" is used. the pressure of the brake chamber on the slack adjuster turns the power
screw. the power screw clamps the disc or rotor between the brake lining pads of a caliper, similar to a large c-clamp.
Wedge brakes and disc brakes are less common than s-cam brakes.
5.1.9 – Supply Pressure Gauges
All vehicles with air brakes have a pressure gauge connected to the air tank. If the vehicle has a dual air brake system,
there will be a gauge for each half of the system. (or a single gauge with two needles.) dual systems will be discussed
later. these gauges tell you how much pressure is in the air tanks.
5.1.10 – Application Pressure Gauge
this gauge shows how much air pressure you are applying to the brakes. (this gauge is not on all vehicles.) Increasing
application pressure to hold the same speed means the brakes are fading. You should slow down and use a lower gear.
the need for increased pressure can also be caused by brakes out of adjustment, air leaks, or mechanical problems.
5.1.11 – Low Air Pressure Warning
A low air pressure warning signal is required on vehicles with air brakes. A warning signal you can see must come on
before the air pressure in the tanks falls below 60 psi. (or one half the compressor governor cutout pressure on older
vehicles.) the warning is usually a red light. A buzzer may also come on.
Another type of warning is the "wig wag." this device drops a mechanical arm into your view when the pressure in the
system drops below 60 psi. An automatic wig wag will rise out of your view when the pressure in the system goes above
60 psi. the manual reset type must be placed in the "out of view" position manually. It will not stay in place until the
pressure in the system is above 60 psi.
on large buses it is common for the low pressure warning devices to signal at 80-85 psi.
5.1.12 – Stop Light Switch
drivers behind you must be warned when you put your brakes on. the air brake system does this with an electric switch
that works by air pressure. the switch turns on the brake lights when you put on the air brakes.
5.1.13 – Front Brake Limiting Valve
Some older vehicles (made before 1975) have a front brake limiting valve and a control in the cab. the control is usually
marked "normal" and "slippery." When you put the control in the "slippery" position, the limiting valve cuts the "normal" air
pressure to the front brakes by half. Limiting valves were used to reduce the chance of the front wheels skidding on
slippery surfaces. However, they actually reduce the stopping power of the vehicle. Front wheel braking is good under all
conditions. tests have shown front wheel skids from braking are not likely even on ice. make sure the control is in the
"normal" position to have normal stopping power.
many vehicles have automatic front wheel limiting valves. they reduce the air to the front brakes except when the brakes
are put on very hard (60 psi or more application pressure). these valves cannot be controlled by the driver.
5.1.14 – Spring Brakes
All trucks, truck tractors, and buses must be equipped with emergency brakes and parking brakes. they must be held on
by mechanical force (because air pressure can eventually leak away). Spring brakes are usually used to meet these needs.
When driving, powerful springs are held back by air pressure. If the air pressure is removed, the springs put on the brakes.
A parking brake control in the cab allows the driver to let the air out of the spring brakes. this lets the springs put the brakes
on. A leak in the air brake system, which causes all the air to be lost, will also cause the springs to put on the brakes.
tractor and straight truck spring brakes will come fully on when air pressure drops to range of 40 to 20 psi. do not wait for
the brakes to come on automatically. When the low air pressure warning light and buzzer first come on, bring the vehicle
to a safe stop right away, while you can still control the brakes.
the braking power of spring brakes depends on the brakes being in adjustment. If the brakes are not adjusted properly,
neither the regular brakes nor the emergency/parking brakes will work right.
Section-5 Air Brakes
5-3
5.1.15 – Parking Brake Controls
Commercial Driver’s License Manual
In newer vehicles with air brakes, you put on the parking brakes using a diamond-shaped, yellow, push-pull control knob.
You pull the knob out to put the parking brakes (spring brakes) on, and push it in to release them. on older vehicles, the
parking brakes may be controlled by a lever. use the parking brakes whenever you park.
caution. never push the brake pedal down when the spring brakes are on. If you do, the brakes could be damaged by
the combined forces of the springs and the air pressure. many brake systems are designed so this will not happen. But
not all systems are set up that way, and those that are may not always work. It is much better to develop the habit of not
pushing the brake pedal down when the spring brakes are on.
modulating control valves. In some vehicles a control handle on the dash board may be used to apply the spring
brakes gradually. this is called a modulating valve. It is spring-loaded so you have a feel for the braking action. the more
you move the control lever, the harder the spring brakes come on. they work this way so you can control the spring
brakes if the service brakes fail. When parking a vehicle with a modulating control valve, move the lever as far as it will go
and hold it in place with the locking device.
dual Parking control valves. When main air pressure is lost, the spring brakes come on. Some vehicles, such as buses,
have a separate air tank which can be used to release the spring brakes. this is so you can move the vehicle for a short
distance or in the case of an emergency. one of the valves is a push-pull type and is used to put on the spring brakes for
parking. the other valve is spring loaded in the "out" position. When you push the control in, air from the separate air tank
releases the spring brakes so you can move. When you release the button, the spring brakes come on again. there is
only enough air in the separate tank to do this a few times. therefore, plan carefully when moving. otherwise, you may be
stopped in a dangerous location when the separate air supply runs out. See Figure 5.3.
5.1.16 – Antilock Braking Systems (ABS)
truck tractors with air brakes built on or after march 1, 1997, and other air brakes vehicles, (trucks, buses, trailers, and
converter dollies) built on or after march 1, 1998, are required to be equipped with antilock brakes. many commercial
vehicles built before these dates have been voluntarily equipped with ABS. check the certification label for the date of
manufacture to determine if your vehicle is equipped with ABS.
ABS is a computerized system that keeps your wheels from locking
up during hard brake applications. vehicles with ABS have yellow
malfunction lamps to tell you if something is not working.
tractors, trucks, and buses will have yellow ABS malfunction lamps on
the instrument panel.
figure 5.3
trailers will have yellow ABS malfunction lamps on the left side, either on
the front or rear corner. dollies manufactured on or after march 1, 1998
are required to have a lamp on the left side.
on newer vehicles, the malfunction lamp comes on at start-up for a bulb
check, and then goes out quickly. on older systems, the lamp could stay
on until you are driving over five mph.
If the lamp stays on after the bulb check, or goes on once you are under
way, you may have lost ABS control at one or more wheels.
In the case of towed units manufactured before it was required by the
department of transportation, it may be difficult to tell if the unit is
equipped with ABS. Look under the vehicle for the electronic control
unit (Ecu) and wheel speed sensor wires coming from the back of the
brakes.
ABS is an addition to your normal brakes. It does not decrease or
increase your normal braking capability. ABS only activates when wheels
are about to lock up.
ABS does not necessarily shorten your stopping distance, but it does help
you keep the vehicle under control during hard braking.
5-4
Section-5 Air Brakes
Commercial Driver’s License Manual
figure 5.4
1.
2.
3.
4.
5.
6.
subsection 5.1
test Your Knowledge
Why must air tanks be drained?
What is a supply pressure gauge used for?
All vehicles with air brakes must have a low air pressure warning signal. true or False?
What are spring brakes?
Front wheel brakes are good under all conditions. true or False?
How do you know if your vehicle is equipped with antilock brakes?
these questions may be on your test. If you cannot answer them all, re-read subsection 5.1.
Section-5 Air Brakes
5-5
5.2 – dUal aIR bRaKe
Commercial Driver’s License Manual
most heavy-duty vehicles use dual air brake systems for safety. A dual air brake system has two separate air brake
systems, which use a single set of brake controls. Each system has its own air tanks, hoses, lines, etc. one system
typically operates the regular brakes on the rear axle or axles. the other system operates the regular brakes on the front
axle (and possibly one rear axle). Both systems supply air to the trailer (if there is one). the first system is called the
"primary" system. the other is called the "secondary" system. See Figure 5.4.
Before driving a vehicle with a dual air system, allow time for the air compressor to build up a minimum of 100 psi
pressure in both the primary and secondary systems. Watch the primary and secondary air pressure gauges (or needles,
if the system has two needles in one gauge). Pay attention to the low air pressure warning light and buzzer. the warning
light and buzzer should shut off when air pressure in both systems rises to a value set by the manufacturer. this value
must be greater than 60 psi.
the warning light and buzzer should come on before the air pressure drops below 60 psi in either system. If this happens
while driving, you should stop right away and safely park the vehicle. If one air system is very low on pressure, either the
front or the rear brakes will not be operating fully. this means it will take you longer to stop. Bring the vehicle to a safe
stop, and have the air brakes system fixed.
5.3 – InsPectInG aIR bRaKe sYstems
You should use the basic seven-step inspection procedure described in Section 2 to inspect your vehicle. there are more
things to inspect on a vehicle with air brakes than one without them. these things are discussed below, in the order they
fit into the seven-step method.
5.3.1 – During Step 2 Engine Compartment Checks
check Air compressor drive Belt (if compressor is belt-driven). If the air compressor is belt-driven, check the condition
and tightness of the belt. It should be in good condition.
5.3.2 – During Step 5 Walkaround Inspection
check Slack Adjusters on S-cam Brakes. Park on level ground and chock the wheels to prevent the vehicle from moving.
release the parking brakes so you can move the slack adjusters. use gloves and pull hard on each slack adjuster that
you can reach. If a slack adjuster moves more than about one inch where the push rod attaches to it, it probably needs
adjustment. Adjust it or have it adjusted. vehicles with too much brake slack can be very hard to stop. out-of-adjustment
brakes are the most common problem found in roadside inspections. Be safe. check the slack adjusters.
All vehicles built since 1994 have automatic slack adjustors. Even though automatic slack adjustors adjust themselves
during full brake applications, they must be checked.
Automatic adjusters should not have to be manually adjusted except when performing maintenance on the brakes and
during installation of the slack adjusters. In a vehicle equipped with automatic adjusters, when the pushrod stroke
exceeds the legal brake adjustment limit, it is an indication that a mechanical problem exists in the adjuster itself, a
problem with the related foundation brake components, or that the adjuster was improperly installed.
the manual adjustment of an automatic adjuster to bring a brake pushrod stroke within legal limits is generally masking
a mechanical problem and is not fixing it. Further, routine adjustment of most automatic adjusters will likely result in
premature wear of the adjuster itself. It is recommended that when brakes equipped with automatic adjusters are found
to be out of adjustment, the driver take the vehicle to a repair facility as soon as possible to have the problem corrected.
the manual adjustment of automatic slack adjusters is dangerous because it may give the driver a false sense of security
regarding the effectiveness of the braking system.
the manual adjustment of an automatic adjuster should only be used as a temporary measure to correct the adjustment
in an emergency situation as it is likely the brake will soon be back out of adjustment since this procedure usually does
not fix the underlying adjustment problem.
(note: Automatic slack adjusters are made by different manufacturers and do not all operate the same. therefore, the
specific manufacturer’s Service manual should be consulted prior to troubleshooting a brake adjustment problem).
5-6
Section-5 Air Brakes
Commercial Driver’s License Manual
check brake drums (or discs), linings, and Hoses. Brake drums (or discs) must not have cracks longer than one half
the width of the friction area. Linings (friction material) must not be loose or soaked with oil or grease. they must not be
dangerously thin. mechanical parts must be in place, not broken or missing. check the air hoses connected to the brake
chambers to make sure they are not cut or worn due to rubbing.
5.3.3 – Step 7 Final Air Brake Check
do the following checks instead of the hydraulic brake check shown in
Section 2, Step 7: check Brake System.
test air leakage Rate. With a fully-charged air system (typically 125
psi), turn off the engine, release the parking brake, and time the air pressure drop. the loss rate should be less than two psi in one minute for
single vehicles and less than three psi in one minute for combination vehicles. then apply 90 psi or more with the brake pedal. After the initial
pressure drop, if the air pressure falls more than three psi in one minute
for single vehicles (more than four psi for combination
vehicles), the air loss rate is too much. check for air leaks and fix before
driving the vehicle. otherwise, you could lose your brakes while driving.
figure 5.5
test low Pressure Warning signal. Shut the engine off when you have
enough air pressure so that the low pressure warning signal is not on.
turn the electrical power on and step on and off the brake pedal to
reduce air tank pressure. the low air pressure warning signal must come
on before the pressure drops to less than 60 psi in the air tank (or tank
with the lowest air pressure, in dual air systems). See Figure 5.5.
If the warning signal does not work, you could lose air pressure and you
would not know it. this could cause sudden emergency braking in a
single-circuit air system. In dual systems the stopping distance will be
increased. only limited braking can be done before the spring brakes
come on.
check that spring brakes come on automatically. Park on level
ground, chock the wheels, release the parking brakes when you have
enough air pressure to do it, and shut the engine off. continue to fan off
the air pressure by stepping on and off the brake pedal to reduce tank
pressure. the tractor protection valve and parking brake valve should
close (pop out) on a tractor-trailer combination vehicle and the parking
brake valve should close (pop out) on other combination and single vehicle types when the air pressure falls to the manufacturer’s specification (40 – 20 psi). this will cause the spring brakes to
come on.
check Rate of air Pressure buildup. When the engine is at operating rpms, the pressure should build from 85 to 100
psi within 45 seconds in dual air systems. (If the vehicle has larger than minimum air tanks, the buildup time can be longer
and still be safe. check the manufacturer’s specifications.) In single air systems (pre-1975), typical requirements are
pressure buildup from 50 to 90 psi within 3 minutes with the engine at an idle speed of 600-900 rpms.
If air pressure does not build up fast enough, your pressure may drop too low during driving, requiring an emergency stop.
do not drive until you get the problem fixed.
check air compressor Governor cut-in and cut-out Pressures. Pumping by the air compressor should start at about
100 psi and stop at about 125 psi. (check manufacturer’s specifications.) run the engine at a fast idle. the air governor
should cut-out the air compressor at about the manufacturer’s specified pressure. the air pressure shown by your
gauge(s) will stop rising. With the engine idling, step on and off the brake to reduce the air tank pressure. the compressor
should cut-in at about the manufacturer’s specified cut-in pressure. the pressure should begin to rise.
If the air governor does not work as described above, it may need to be fixed. A governor that does not work properly may
not keep enough air pressure for safe driving.
test Parking brake. Stop the vehicle, put the parking brake on, and gently pull against it in a low gear to test that the
parking brake will hold.
Section-5 Air Brakes
5-7
Commercial Driver’s License Manual
test service brakes. Wait for normal air pressure, release the parking brake, move the vehicle forward slowly (about five
mph), and apply the brakes firmly using the brake pedal. note any vehicle "pulling" to one side, unusual feel, or delayed
stopping action.
this test may show you problems, which you otherwise would not know about until you needed the brakes on the road.
1.
2.
3.
4.
5.
6.
subsections 5.2 and 5.3
test Your Knowledge
What is a dual air brake system?
What are the slack adjusters?
How can you check slack adjusters?
How can you test the low pressure warning signal?
How can you check that the spring brakes come on automatically?
What are the maximum leakage rates?
these questions may be on your test. If you cannot answer them all, re-read subsections 5.2 and 5.3.
5.4 – UsInG aIR bRaKes
5.4.1 – Normal Stops
Push the brake pedal down. control the pressure so the vehicle comes to a smooth, safe stop. If you have a manual
transmission, do not push the clutch in until the engine rpm is down close to idle. When stopped, select a starting gear.
5.4.2 – Braking with Antilock Brakes
When you brake hard on slippery surfaces in a vehicle without ABS, your wheels may lock up. When your steering wheels
lock up, you lose steering control. When your other wheels lock up, you may skid, jackknife, or even spin the vehicle.
ABS helps you avoid wheel lock up. the computer senses impending lockup, reduces the braking pressure to a safe
level, and you maintain control.
You may or may not be able to stop faster with ABS, but you should be able to steer around an obstacle while braking,
and avoid skids caused by over braking.
Having ABS on only the tractor, only the trailer, or even on only one axle, still gives you more control over the vehicle
during braking. Brake normally.
When only the tractor has ABS, you should be able to maintain steering control, and there is less chance of jackknifing.
But, keep your eye on the trailer and let up on the brakes (if you can safely do so) if it begins to swing out.
When only the trailer has ABS, the trailer is less likely to swing out, but if you lose steering control or start a tractor
jackknife, let up on the brakes (if you can safely do so) until you gain control.
When you drive a tractor-trailer combination with ABS, you should brake as you always have. In other words:
•
•
•
use only the braking force necessary to stop safely and stay in control.
Brake the same way, regardless of whether you have ABS on the tractor, the trailer, or both.
As you slow down, monitor your tractor and trailer and back off the brakes (if it is safe to do so) to stay in control.
there is only one exception to this procedure, if you always drive a straight truck or combination with working ABS on all
axles, in an emergency stop, you can fully apply the brakes.
Without ABS, you still have normal brake functions. drive and brake as you always have.
remember, if your ABS malfunctions, you still have regular brakes. drive normally, but get the system serviced soon.
5-8
Section-5 Air Brakes
Commercial Driver’s License Manual
5.4.3 – Emergency Stops
If somebody suddenly pulls out in front of you, your natural response is to hit the brakes. this is a good response if there
is enough distance to stop, and you use the brakes correctly.
You should brake in a way that will keep your vehicle in a straight line and allow you to turn if it becomes necessary. You
can use the "controlled braking" method or the "stab braking" method.
controlled braking. With this method, you apply the brakes as hard as you can without locking the wheels. Keep
steering wheel movements very small while doing this. If you need to make a larger steering adjustment or if the wheels
lock, release the brakes. re-apply the brakes as soon as you can.
stab braking.
• Apply the brakes as hard as you can.
• release brakes when wheels lock up.
• As soon as the wheels start rolling, apply the brakes fully again. (It can take up to one second for the wheels to
start rolling after you release the brakes. If you re-apply the brakes before the wheels start rolling, the vehicle
will not straighten out.)
note: If you drive a vehicle with anti-lock brakes, you should read and follow the directions found in the
owner’s manual for stopping quickly.
5.4.4 – Stopping Distance
Stopping distance was described in Section 2 under
"Speed and Stopping distance." With air brakes
there is an added delay--“Brake Lag”. this is the time
required for the brakes to work after the brake pedal
is pushed. With hydraulic brakes (used on cars and
light/medium trucks), the brakes work instantly.
However, with air brakes, it takes a little time (one
half second or more) for the air to flow through the
lines to the brakes. thus, the total stopping distance
for vehicles with air brake systems is made up of four
different factors.
figure 5.6
Perception distance + reaction distance + Brake
Lag distance + Braking distance = total Stopping
distance
the air brake lag distance at 55 mph on dry
pavement adds about 32 feet. So at 55 mph for
an average driver under good traction and brake
conditions, the total stopping distance is more than
300 feet. See Figure 5.6.
5.4.5 – Brake Fading or Failure
Brakes are designed so brake shoes or pads rub
against the brake drum or disks to slow the vehicle.
Braking creates heat, but brakes are designed to
take a lot of heat. However, brakes can fade or fail from excessive heat caused by using them too much and not relying
on the engine braking effect.
Excessive use of the service brakes results in overheating and leads to brake fade. Brake fade results from excessive
heat causing chemical changes in the brake lining, which reduce friction, and also causing expansion of the brake drums.
As the overheated drums expand, the brake shoes and linings have to move farther to contact the drums, and the force of
this contact is reduced. continued overuse may increase brake fade until the vehicle cannot be slowed down or stopped.
Brake fade is also affected by adjustment. to safely control a vehicle, every brake must do its share of the work. Brakes
out of adjustment will stop doing their share before those that are in adjustment. the other brakes can then overheat and
fade, and there will not be enough braking available to control the vehicle(s). Brakes can get out of adjustment quickly,
especially when they are hot. therefore, check brake adjustment often.
Section-5 Air Brakes
5-9
5.4.6 – Proper Braking Technique (SNUB Braking)
Commercial Driver’s License Manual
Remember. the use of brakes on a long and/or steep downgrade is only a supplement to the braking effect of the engine.
once the vehicle is in the proper low gear, the following is the proper braking technique:
1. Apply the brakes just hard enough to feel a definite slowdown.
2. When your speed has been reduced to approximately five mph below your "safe" speed, release the brakes.
(this brake application should last for about three seconds.)
3. When your speed has increased to your "safe" speed, repeat steps 1 and 2.
For example, if your "safe" speed is 40 mph, you would not apply the brakes until your speed reaches 40 mph. You now
apply the brakes hard enough to gradually reduce your speed to 35 mph and then release the brakes. repeat this as
often as necessary until you have reached the end of the downgrade.
5.4.7 – Low Air Pressure
If the low air pressure warning comes on, stop and safely park your vehicle as soon as possible. there might be an air
leak in the system. controlled braking is possible only while enough air remains in the air tanks. the spring brakes will
come on when the air pressure drops into the range of 20 to 45 psi. A heavily loaded vehicle will take a long distance to
stop because the spring brakes do not work on all axles. Lightly loaded vehicles or vehicles on slippery roads may skid
out of control when the spring brakes come on. It is much safer to stop while there is enough air in the tanks to use the foot
brakes.
5.4.8 – Parking Brakes
Any time you park, use the parking brakes, except as noted below. Pull the parking brake control knob out to apply the
parking brakes, push it in to release. the control will be a yellow, diamond-shaped knob labeled "parking brakes" on
newer vehicles. on older vehicles, it may be a round blue knob or some other shape (including a lever that swings from
side to side or up and down).
do not use the parking brakes if the brakes are very hot (from just having come down a steep grade), or if the brakes are
very wet in freezing temperatures. If they are used while they are very hot, they can be damaged by the heat. If they are
used in freezing temperatures when the brakes are very wet, they can freeze so the vehicle cannot move. use wheel
chocks on a level surface to hold the vehicle. Let hot brakes cool before using the parking brakes. If the brakes are wet,
use the brakes lightly while driving in a low gear to heat and dry them.
If your vehicle does not have automatic air tank drains, drain your air tanks at the end of each working day to remove
moisture and oil. otherwise, the brakes could fail.
never leave your vehicle unattended without applying the parking brakes or chocking the wheels. Your vehicle
might roll away and cause injury and damage.
5 - 10
Section-5 Air Brakes
Commercial Driver’s License Manual
1.
2.
3.
4.
5.
6.
7.
subsection 5.4
test Your Knowledge
Why should you be in the proper gear before starting down a hill?
What factors can cause brakes to fade or fail?
the use of brakes on a long, steep downgrade is only a supplement to the braking effect of the engine. true or False?
If you are away from your vehicle only a short time, you do not need to use the parking brake. true or False?
How often should you drain air tanks?
How do you brake when you drive a tractor-trailer combination with ABS?
You still have normal brake functions if your ABS is not working. true or False?
these questions may be on your test. If you cannot answer them all, re-read subsection 5.4.
Section-5 Air Brakes
5 - 11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement