Connection SLI 2.2, SLI 4.2 Owner's Manual

Add to my manuals
16 Pages

advertisement

Connection SLI 2.2, SLI 4.2 Owner's Manual | Manualzz

OWNER’S MANUAL

SLI 2.2 - SLI 4.2

connection.eu

Manuale SLI 2/ SLI 4_2019.indd 1 22/05/19 15:19

Manuale SLI 2/ SLI 4_2019.indd 2 22/05/19 15:19

WARNING

• Before you start your installation, make sure you carefully read and understand all instructions.

Disregarding them might cause accidental harms or damage your devices.

• The vehicle electric system must have 12 VDC voltage with negative to ground. Make sure

your car has it in order to avoid any damages to your amplifier and to the vehicle.

• Install the device in the vehicle parts where temperature is between 0° C (32° F) and 55° C (131° F).

• Make sure the location you chose for the components does not affect the correct functioning

of the vehicle mechanical and electric devices.

• Do not run the cables or install the device next to electronic gearcases.

• Always wear protective eyewear when using tools that may generate splinters.

• When installation is over, and before plugging the main power supply fuse, check the system

wiring and make sure all connections were done in the right way.

• Safety must be at the first place while driving. Listening volume must never cover noise coming from

the outside and from the vehicle, in order for you to be able to promptly face emergency situation.

• Always insulate the connection between the SLI and the OEM headunit / OEM amplifier to

avoid damage them.

• Always insulate the connection between the SLI and the +12V power supply system (battery).

• Always fuse +12 V SLI cable (RED) with 1A fuse to avoid any damage to the vehicle electrical

system and or event of fire.

Elettromedia will not be liable for the direct or indirect damages due to a wrong use or a wrong connection of the device.

Manuale SLI 2/ SLI 4_2019.indd 3

3

22/05/19 15:19

PACKAGING CONTENTS

SLI 2.2

SLI 4.2

x 4 x 4

4

Manuale SLI 2/ SLI 4_2019.indd 4 22/05/19 15:19

INSTALLATION - FIXING - SIZE

SLI 2.2 SLI 4.2

CLICK

Manuale SLI 2/ SLI 4_2019.indd 5

W

H

D

SLI 2.2

SLI 4.2

W H D

61

(2.4)

82

(3.2)

28

(1.1)

61

(2.4)

102

(4)

28

(1.1) mm

(in.) mm

(in.)

5

22/05/19 15:19

CONNECTIONS

SLI 2.2

UNIVERSAL SPEAKERS

SIMULATOR circuit, simulates the load of the OEM speakers on the 4 Front + Rear input channels, for a complete compatibility with OEM

Headunit / OEM Amplifier.

SLI 2.2 CABLE OUTPUT VIEW

(Red) +12V

(Blue) REM OUT

(Purple) IN RR+

(Green) IN RL+

(Grey) IN FR+

(White) IN FL+

NC

NC

(Grey) OUT FR+

(White) OUT FL+

GND (Black)

NC

IN RR- (Purple/Black)

IN RL- (Green/Black)

IN FR- (Grey/Black)

IN FL- (White/Black)

NC

NC

OUT FR- (Grey/Black)

OUT FL- (White/Black)

+12V

GND

Rem Out

RCA

Front Left

Out

RCA

Front Right

Out

IN RR+

IN RR-

IN RL+

IN RL-

IN FR+

IN FR-

IN FL+

IN FL-

Rear

Right

Rear

Left

Front

Right

Front

Left

* Conversion not operated for Rear input channels on SLI2.2, only USS and ART function is active on these inputs.

6

Manuale SLI 2/ SLI 4_2019.indd 6 22/05/19 15:19

CONNECTIONS

SLI 4.2

UNIVERSAL SPEAKERS

SIMULATOR circuit, simulates the load of the OEM speakers on the 4 Front + Rear input channels, for a complete compatibility with OEM

Headunit / OEM Amplifier.

SLI 4.2 CABLE OUTPUT VIEW

(Red) +12V

(Blue) REM OUT

(Purple) IN RR+

(Green) IN RL+

(Grey) IN FR+

(White) IN FL+

(Purple) OUT RR+

(Green) OUT RL+

(Grey) OUT FR+

(White) OUT FL+

GND (Black)

NC

IN RR- (Purple/Black)

IN RL- (Green/Black)

IN FR- (Grey/Black)

IN FL- (White/Black)

OUT RR- (Purple/Black)

OUT RL- (Green/Black)

OUT FR- (Grey/Black)

OUT FL- (White/Black)

Out

RCA

Rear Left

RCA

Front Left

Out

RCA

Front Right

Out

RCA

Rear Right

Out

IN RR+

IN RR-

IN RL+

IN RL-

IN FR+

IN FR-

IN FL+

IN FL-

+12V

GND

Rem Out

Rear

Right

Rear

Left

Front

Right

Front

Left

Manuale SLI 2/ SLI 4_2019.indd 7

7

22/05/19 15:19

CONNECTIONS: SLI 2.2 with OEM Headunit (without ART ™ function)

OFF

ON

High Power

(OEM AMP)

Low Power

(OEM SOURCE)

OEM Headunit

+ Batt

IN (high level)

Remote

OUT (low level)

DSR: DOUBLE STEP-DOWN RATIO, allows correct level interfacing with OEM Headunit or OEM Amplifier by switch selection.

8

Manuale SLI 2/ SLI 4_2019.indd 8 22/05/19 15:19

CONNECTIONS: SLI 2.2 with OEM Headunit (with ART ™ function)

ART TM FUNCTION

OFF

ON

High Power

(OEM AMP)

Low Power

(OEM SOURCE)

OEM Headunit

+ Batt

IN (high level)

+ Batt

Remote

OUT (low level)

RED

+12 V

GND

Black

REM OUT

Blue

*

DSR: DOUBLE STEP-DOWN RATIO, allows correct level interfacing with OEM Headunit or OEM Amplifier by switch selection.

ART™: AUTOMATIC REMOTE TURN-ON/OFF function, generates a 12 V remote output when the OEM Headunit / Amplifier is turned ON/OFF

(available only when SLI is powered).

Conversion not operated for Rear input channels on SLI2.2, only USS and ART function is active on these inputs.

** In countries where the legislation on electromagnetic compatibility is not mandatory under ECE / UN Regulation no. 10/5.

Manuale SLI 2/ SLI 4_2019.indd 9

9

22/05/19 15:19

CONNECTIONS: SLI 4.2 with OEM Headunit (without ART ™ function)

OFF

ON

High Power

(OEM AMP)

Low Power

(OEM SOURCE)

OEM Headunit

+ Batt

Front Rear

IN (high level)

Remote

OUT (low level)

Front

Rear

DSR: DOUBLE STEP-DOWN RATIO, allows correct level interfacing with OEM Headunit or OEM Amplifier by switch selection.

10

Manuale SLI 2/ SLI 4_2019.indd 10 22/05/19 15:19

CONNECTIONS: SLI 4.2 with OEM Headunit (with ART ™ function)

ART TM FUNCTION

OFF

ON

High Power

(OEM AMP)

Low Power

(OEM SOURCE)

OEM Headunit

+ Batt

Front

+ Batt

Rear

IN (high level)

Remote

OUT (low level)

Front

Rear

**

DSR: DOUBLE STEP-DOWN RATIO, allows correct level interfacing with OEM Headunit or OEM Amplifier by switch selection.

ART™: AUTOMATIC REMOTE TURN-ON/OFF function, generates a 12 V remote output when the OEM Headunit / Amplifier is turned ON/OFF

(available only when SLI is powered).

In countries where the legislation on electromagnetic compatibility is not mandatory under ECE / UN Regulation no. 10/5.

RED

+12 V

GND

Black

REM OUT

Blue

11

Manuale SLI 2/ SLI 4_2019.indd 11 22/05/19 15:19

CONNECTIONS: SLI 2.2 with OEM Amplifier (with ART ™ function)

ART TM FUNCTION

OFF

ON

High Power

(OEM AMP)

Low Power

(OEM SOURCE)

OEM

AMPLIFIER

+ Batt

IN

(high level)

Remote

OUT (low level)

RED

+12 V

GND

Black

REM OUT

Blue

12

*

DSR: DOUBLE STEP-DOWN RATIO, allows correct level interfacing with OEM Headunit or OEM Amplifier by switch selection.

ART™: AUTOMATIC REMOTE TURN-ON/OFF function, generates a 12 V remote output when the OEM Headunit / Amplifier is turned ON/OFF

(available only when SLI is powered).

Conversion not operated for Rear input channels on SLI2.2, only USS and ART function is active on these inputs.

** In countries where the legislation on electromagnetic compatibility is not mandatory under ECE / UN Regulation no. 10/5.

Manuale SLI 2/ SLI 4_2019.indd 12 22/05/19 15:19

CONNECTIONS: SLI 4.2 with OEM Amplifier (with ART ™ function)

ART TM FUNCTION

OFF

ON

High Power

(OEM AMP)

Low Power

(OEM SOURCE)

OEM

AMPLIFIER

+ Batt

Rear

Front

IN (high level)

OUT (low level)

Remote

Front

Rear

**

DSR: DOUBLE STEP-DOWN RATIO, allows correct level interfacing with OEM Headunit or OEM Amplifier by switch selection.

ART™: AUTOMATIC REMOTE TURN-ON/OFF function, generates a 12 V remote output when the OEM Headunit / Amplifier is turned ON/OFF

(available only when SLI is powered).

In countries where the legislation on electromagnetic compatibility is not mandatory under ECE / UN Regulation no. 10/5.

RED

+12 V

GND

Black

REM OUT

Blue

Manuale SLI 2/ SLI 4_2019.indd 13

13

22/05/19 15:19

TECHNICAL SPECIFICATIONS

Input / Output Channels

Maximum Input Power

Nominal Conversion Ratio

Input Impedance **

Output Impedance

Distortion

(THD+N@25W rms input , Lo-Power)

Frequency Response (-3dB)

Remote Out ***

(Only when LSI is Powered)

Weight (kg. / lb.) including cable

SLI 2.2

4*/2

SLI 4.2

4/4

50W@4Ω (Lo-Power) / 150W@4Ω (Hi-Power)

4:1 Lo-Power / 8:1 Hi-Power

200 Ω

400 Ω

0,15% 100 Hz,

0,07% 1 kHz,

0,07% 10 kHz

15 ÷ 40 kHz

12 VDC - 100mA max @ 13 VDC input

0,16 (0.36) 0,25 (0.55)

* Conversion not operated for Rear input channels on SLI2.2, only USS and ART function is active on these inputs.

*** In countries where the legislation on electromagnetic compatibility is not mandatory under ECE / UN Regulation no. 10/5.

14

Manuale SLI 2/ SLI 4_2019.indd 14 22/05/19 15:19

Manuale SLI 2/ SLI 4_2019.indd 15 22/05/19 15:19

WARRANTY

The products are guaranteed according to the laws in force.

Possible damaged products must be sent back, with authorization, to

CONNECTION dealer to be repaired or replaced.

Products damaged by incorrect use/installation are not covered by warranty.

INFO

In Italy: [email protected]

Abroad: [email protected]

16

CONNECTION PART OF ELETTROMEDIA

62018 Potenza Picena (MC) Italy - T +39 0733 870 870 - F +39 0733 870 880 - www.elettromedia.it

Manuale SLI 2/ SLI 4_2019.indd 16 22/05/19 15:19

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement