2008 WaveRunner FX SHO FX Cruiser SHO OWNER`S

2008 WaveRunner FX SHO FX Cruiser SHO OWNER`S
2008 WaveRunner
FX SHO
FX Cruiser SHO
OWNER’S/OPERATOR’S MANUAL
U.S.A. Edition
READ THIS MANUAL
CAREFULLY BEFORE OPERATION!
LIT-18626-07-87
F1W-F8199-10
UF1W10E0.book Page 1 Monday, November 26, 2007 3:57 PM
UF1W10E0.book Page 1 Monday, November 26, 2007 3:57 PM
Important manual information
EJU30180
To the owner/operator
Thank you for choosing a Yamaha watercraft.
This owner’s/operator’s manual contains information you will need for proper operation,
maintenance, and care. A thorough understanding of these simple instructions will help
you to obtain maximum enjoyment from your
new Yamaha. If you have any questions
about the operation or maintenance of your
watercraft, please consult a Yamaha dealer.
Because Yamaha has a policy of continuing
product improvement, this product may not be
exactly as described in this owner’s/operator’s manual. Specifications are subject to
change without notice.
This manual should be considered a permanent part of this watercraft and should remain
with it even if the watercraft is subsequently
sold.
In this manual, information of particular importance is distinguished in the following ways:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
EWJ00070
WARNING
Failure to follow WARNING instructions
could result in severe injury or death to the
machine operator, passengers, a bystander, or a person inspecting or repairing the
watercraft.
ECJ00090
CAUTION:
A CAUTION indicates special precautions
that must be taken to avoid damage to the
watercraft.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
EJU30220
WaveRunner FX SHO/FX Cruiser SHO
OWNER’S/OPERATOR’S MANUAL
©2007 by Yamaha Motor Corporation,
USA
1st Edition, November 2007
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in USA
P/N LIT-18626-07-87
UF1W10E0.book Page 1 Monday, November 26, 2007 3:57 PM
Table of contents
General and important labels........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Hull Identification Number (HIN) ........ 1
Engine serial number ........................ 1
Emission control information .......... 2
Approval label of emission control
certificate ........................................ 2
Manufactured date label .................... 3
Star labels ......................................... 3
Important labels .............................. 5
Warning labels ................................... 6
Other labels ....................................... 8
Safety information........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 13
Recommended equipment ........... 15
Hazard information ....................... 16
Watercraft characteristics ............. 16
Water-skiing ................................. 18
Rules of the Road ........................ 20
To get more boating safety
information ................................ 24
Enjoy your watercraft
responsibly ................................ 25
Features and functions................... 26
Location of main components ...... 26
Operation of controls and other
functions .................................... 30
Seats ...............................................
Hood ................................................
Fuel tank filler cap ...........................
Remote control transmitter ..............
Engine stop switch ..........................
Engine shut-off switch .....................
Start switch ......................................
Right handlebar switches ................
Throttle lever ...................................
30
31
31
32
33
33
34
34
34
Cooling water pilot outlets ...............
Steering system ...............................
Tilt lever ...........................................
Shift lever ........................................
Quick Shift Trim System (QSTS)
selector ........................................
Handgrip ..........................................
Reboarding step ..............................
Bow eye ...........................................
Stern eyes .......................................
Pull-up cleats
(for FX Cruiser SHO) ...................
Yamaha Engine Management
System (YEMS) ...........................
Yamaha Security System ................
No-wake mode ................................
Cruise assist ....................................
Multifunction information center ......
Storage compartments ....................
34
35
36
36
37
39
39
39
40
40
40
40
42
44
45
55
Operation ......................................... 59
Fuel and oil .................................. 59
Gasoline .......................................... 59
Engine oil ......................................... 60
Filling the fuel tank .......................... 60
Pre-operation checks ................... 61
Pre-operation check list ................... 61
Pre-operation check points .............. 63
Operation ..................................... 71
Engine break-in ...............................
Launching the watercraft .................
Starting the engine ..........................
Stopping the engine ........................
Leaving the watercraft .....................
71
72
72
74
74
Operating your watercraft ............ 74
Getting to know your watercraft .......
Learning to operate your
watercraft .....................................
Riding with passengers ...................
Starting the watercraft .....................
Boarding and starting in
deep water ...................................
Capsized watercraft .........................
Turning the watercraft .....................
74
74
75
76
77
80
81
UF1W10E0.book Page 2 Monday, November 26, 2007 3:57 PM
Table of contents
Stopping the watercraft ...................
Beaching the watercraft ...................
Docking the watercraft .....................
Reverse on waterways ....................
Rough water operation ....................
82
83
83
83
83
Post-operation care ...................... 84
Transporting ................................. 85
Maintenance and care..................... 86
Storage ......................................... 86
Flushing the cooling system ............
Lubrication .......................................
Fuel system .....................................
Battery .............................................
Cleaning the watercraft ...................
86
87
87
87
88
Maintenance and adjustments ..... 89
Owner’s/operator’s manual and
tool kit ........................................... 89
Periodic maintenance chart ............. 91
Checking the fuel system ................ 93
Engine oil and oil filter ..................... 93
Air filter element .............................. 94
Checking the jet thrust nozzle
angle ............................................ 94
Checking the shift cable .................. 94
Checking and adjusting the throttle
cable ............................................ 95
Cleaning and adjusting the spark
plugs ............................................ 96
Lubrication points ............................ 98
Checking the battery ....................... 99
Fuel injection system ..................... 101
Specifications ................................ 102
Specifications .............................. 102
Trouble recovery ........................... 103
Troubleshooting ......................... 103
Troubleshooting chart .................... 103
Emergency procedures .............. 106
Cleaning the jet intake and
impeller ...................................... 106
Jumping the battery ....................... 107
Replacing the fuses ....................... 108
Towing the watercraft .................... 109
Submerged watercraft ................... 109
Consumer information ................. 110
Limited warranty ......................... 110
YAMAHA EXTENDED SERVICE
(Y.E.S.) ................................... 112
UF1W10E0.book Page 1 Monday, November 26, 2007 3:57 PM
General and important labels
EJU30260
EJU30300
Identification numbers
Record the Primary Identification (PRI-ID)
number, Hull Identification Number (HIN), and
engine serial number in the spaces provided
for assistance when ordering spare parts from
a Yamaha dealer. Also record and keep these
ID numbers in a separate place in case your
watercraft is stolen.
Hull Identification Number (HIN)
The HIN is stamped on a plate attached to the
aft deck.
EJU30281
Primary Identification (PRI-ID) number
The PRI-ID number is stamped on a plate attached inside the engine compartment.
MODEL:
FX1800-G (FX SHO)
FX1800A-G (FX Cruiser SHO)
1
1
1 Hull Identification Number (HIN) location
EJU30310
Engine serial number
The engine serial number is stamped on a
plate attached to the engine unit.
1
1 Primary Identification (PRI-ID) number location
1 Engine serial number location
1
UF1W10E0.book Page 2 Monday, November 26, 2007 3:57 PM
General and important labels
EJU30350
Emission control information
This engine conforms to 2008 U.S. Environmental Protection Agency (EPA) and/or California Air Resources Board (CARB)
regulations for marine SI engines.
This engine is certified to operate on regular
unleaded gasoline.
EJU30400
Approval label of emission control
certificate
This label is attached to the top of the cylinder
head and to the inside of the engine compartment.
1
1 Emission control information label location
1
1 Emission control information label location
2
UF1W10E0.book Page 3 Monday, November 26, 2007 3:57 PM
General and important labels
EJU30430
Manufactured date label
This label is attached to the top of the cylinder
head.
One Star - Low Emission
The one-star label identifies engines that
meet the Air Resources Board’s Personal
Watercraft and Outboard marine engine 2001
exhaust emission standards. Engines meeting these standards have 75% lower emissions than conventional carbureted twostroke engines. These engines are equivalent
to the U.S. EPA’s 2006 standards for marine
engines.
1
1 Manufactured date label location
EJU30440
Star labels
This watercraft is labeled with a California Air
Resources Board (CARB) star label. See below for a description of your particular label.
Two Stars - Very Low Emission
The two-star label identifies engines that meet
the Air Resources Board’s Personal Watercraft and Outboard marine engine 2004 exhaust emission standards. Engines meeting
these standards have 20% lower emissions
than One Star-Low Emission engines.
1
1 Star label location
3
Three Stars - Ultra Low Emission
The three-star label identifies engines that
meet the Air Resources Board’s Personal
Watercraft and Outboard marine engine 2008
UF1W10E0.book Page 4 Monday, November 26, 2007 3:57 PM
General and important labels
exhaust emission standards or the Sterndrive
and Inboard marine engine 2003-2008 exhaust emission standards. Engines meeting
these standards have 65% lower emissions
than One Star-Low Emission engines.
Four Stars - Super Ultra Low Emission
The four-star label identifies engines that
meet the Air Resources Board’s Sterndrive
and Inboard marine engine 2009 exhaust
emission standards. Personal Watercraft and
Outboard marine engines may also comply
with these standards. Engines meeting these
standards have 90% lower emissions than
One Star-Low Emission engines.
4
UF1W10E0.book Page 5 Monday, November 26, 2007 3:57 PM
General and important labels
EJU30450
Important labels
9
1
3
5
4
11
10
8
2
13
7
5
12
6
UF1W10E0.book Page 6 Monday, November 26, 2007 3:57 PM
General and important labels
EJU35910
Warning labels
1
F1W
-U 4 1
B 1 -0
0
2
6
UF1W10E0.book Page 7 Monday, November 26, 2007 3:57 PM
General and important labels
7
UF1W10E0.book Page 8 Monday, November 26, 2007 3:57 PM
General and important labels
EJU35923
Other labels
8
UF1W10E0.book Page 9 Monday, November 26, 2007 3:57 PM
General and important labels
The following label indicates the correct direction to upright a capsized watercraft.
9
UF1W10E0.book Page 10 Monday, November 26, 2007 3:57 PM
Safety information
EJU30670
The safe use and operation of this watercraft is dependent upon the use of proper
riding techniques, as well as upon the
common sense, good judgment, and expertise of the operator. Every operator
should know the following requirements
before riding the watercraft.
● Before operating the watercraft, read this
owner’s/operator’s manual, the Riding
Practice Guide, the Riding Instruction card,
and all warning and caution labels on the
watercraft. Also, watch the Basic Orientation Video provided with your watercraft.
These materials should give you an understanding of the watercraft and its operation.
● Never allow anyone to operate this watercraft until they too have read this owner’s/operator’s manual, the Riding Practice
Guide, the Riding Instruction card, and all
warning and caution labels, and, if possible,
watched the Basic Orientation Video.
Showing them the video may help reinforce
the information contained in these materials.
EJU30730
Limitations on who may
operate the watercraft
●
●
Yamaha recommends a minimum operator
age of 16 years old.
Adults must supervise use by minors.
Know the operator age and training requirements for your state. A boating safety
course is recommended and may be required in your state. You can find local rules
by contacting the United States Coast
Guard (USCG), the National Association of
State Boating Law Administrators, or your
local Power Squadron.
This watercraft is designed to carry the operator and up to 2 passengers. Never exceed the maximum load limit or allow more
than 3 persons (or 2 persons if a water-skier
is being pulled) to ride the watercraft at any
time.
Maximum load:
240 kg (530 lb)
Load is the total weight of cargo, operator, and passengers.
●
Do not operate the watercraft with any passengers on board until you have considerable practice and experience riding alone.
Operating the watercraft with passengers
requires more skill. Take the time to become accustomed to the handling charac-
10
UF1W10E0.book Page 11 Monday, November 26, 2007 3:57 PM
Safety information
teristics of the watercraft before trying any
difficult maneuvers.
EJU30760
Cruising limitations
●
Scan constantly for people, objects, and
other watercraft. Be alert for conditions that
limit your visibility or block your vision of
others.
●
Operate defensively at safe speeds and
keep a safe distance away from people, objects, and other watercraft.
Do not follow directly behind watercraft or
other boats.
Do not go near others to spray or splash
them with water.
Avoid sharp turns or other maneuvers that
make it hard for others to avoid you or understand where you are going.
Avoid areas with submerged objects or
shallow water.
Take early action to avoid collisions. Remember, watercraft and other boats do not
have brakes.
Do not release the throttle lever when trying
to steer away from objects—you need throttle to steer. Always check throttle and steering controls before starting the watercraft.
Ride within your limits and avoid aggressive
maneuvers to reduce the risk of loss of control, ejection, and collision.
This is a high performance boat—not a toy.
Sharp turns or jumping wakes or waves can
increase the risk of back/spinal injury (paralysis), facial injuries, and broken legs, an-
●
●
●
●
●
●
●
●
11
UF1W10E0.book Page 12 Monday, November 26, 2007 3:57 PM
Safety information
●
●
●
●
kles, and other bones. Do not jump wakes
or waves.
Do not operate the watercraft in rough water, bad weather, or when visibility is poor;
this may lead to an accident causing injury
or death. Be alert to the possibility of adverse weather. Take note of weather forecasts and the prevailing weather conditions
before setting out on your watercraft.
As with any water sport, you should not operate your watercraft without someone else
nearby. If you operate further than swimming distance from shore, you should be
accompanied by another boat or watercraft,
but make sure you stay a safe distance
away. It’s good, common sense!
Never operate in water that is less than 60
cm (2 ft) deep, otherwise you increase your
chance of hitting a submerged object,
which could result in injury.
with another boat, which could result in severe injury or death.
●
Follow navigation rules, and state/provincial and local laws that apply to watercraft.
This watercraft is not equipped with lighting
required for night operation. Do not operate
the watercraft after sunset or before dawn,
otherwise you increase the risk of colliding
12
UF1W10E0.book Page 13 Monday, November 26, 2007 3:57 PM
Safety information
EJU30811
Operation requirements
●
●
All riders must wear a U.S. Coast Guard
(USCG) approved personal flotation device
(PFD) that is suitable for personal watercraft use.
Wear protective clothing. Severe internal
injuries can occur if water is forced into
body cavities as a result of falling into the
water or being near the jet thrust nozzle.
Normal swimwear does not adequately protect against forceful water entry into the rectum or vagina. All riders must wear a
wetsuit bottom or clothing that provides
equivalent protection. Such clothing includes thick, tightly woven, sturdy and
snug-fitting apparel such as denim, but
does not include spandex or similar fabrics,
like those used in bicycle shorts.
1 USCG approved PFD
2 Wetsuit bottom
●
●
Eye protection is recommended to keep
wind, water, and glare from the sun out of
your eyes while you operate your watercraft. Restraining straps for eyewear are
made which are designed to float should
your eyewear fall in the water.
Footwear and gloves are recommended.
Helmets meeting Snell or DOT standards
are required for IJSBA-sanctioned races.
You must decide whether to wear a helmet
while you ride for recreation. You should
13
know that a helmet could help protect you in
certain kinds of accidents and that it could
injure you in others.
A helmet is designed to provide some head
protection. Although helmets cannot protect
against all foreseeable impacts, a helmet
might reduce your injuries in a collision with
a boat or other obstacle.
A helmet may have potential safety hazards, as well. Falling into the water could
risk the chance of the helmet catching water, commonly known as “bucketing”, and
the resulting strain on your neck could
cause choking, severe and permanent neck
injuries, or death. A helmet could also increase the risk of an accident if it reduces
your vision or hearing, or if it distracts you or
increases your fatigue.
How should you decide if a helmet’s potential safety benefits outweigh its potential
risks for you? Consider your particular
riding conditions. Consider factors such as
your riding environment and your riding
style and ability. Also consider the likelihood of traffic congestion, and the water
surface conditions.
If you decide to wear a helmet based upon
your riding circumstances, choose one
carefully. Look for a helmet designed for
personal watercraft use, if possible. Consider a helmet meeting Snell or DOT standards. If you will be engaging in closedcourse competition, follow the helmet requirements of the sanctioning organization.
UF1W10E0.book Page 14 Monday, November 26, 2007 3:57 PM
Safety information
●
NEVER operate the watercraft after consuming alcohol or taking other drugs.
●
●
●
●
●
●
For reasons of safety and proper care of the
watercraft, always perform the pre-operation checks listed on page 61 before operating the watercraft.
The operator and passengers should always keep their feet on the floor of the footwell when the watercraft is in motion. Lifting
your feet increases the chances of losing
your balance, or hitting objects outside the
watercraft with your feet. Do not give a ride
to children if their feet cannot reach the floor
of the footwell.
The passengers should hold on firmly, either to the person in front of them or to the
handgrip provided.
●
●
●
●
Never allow a passenger to ride in front of
the operator.
Always consult your doctor on whether it is
safe for you to ride this watercraft if you are
pregnant or in poor health.
Do not attempt to modify this watercraft!
Modifications to your watercraft may reduce
safety and reliability, and render the watercraft unsafe or illegal for use.
Attach the engine shut-off cord to your left
wrist and keep it free from the handlebars
so that the engine stops if you, the operator,
fall off. After riding, remove the engine shutoff cord from the watercraft to avoid accidental starting or unauthorized use by children or others.
Scan carefully for swimmers and stay away
from swimming areas. Swimmers are hard
to see and you could accidentally hit someone in the water.
Avoid being hit by another boat! You should
always take the responsibility to watch for
traffic; other boaters may not be watching
for you. If they do not see you, or if you maneuver more quickly than other boaters expect, you risk a collision.
Maintain a safe distance from other boats
and watercraft, and also watch for ski ropes
or fishing lines. Obey the “Rules of the
Road” and be sure to check behind you before making a turn. (See “Rules of the
Road” on page 20.)
14
UF1W10E0.book Page 15 Monday, November 26, 2007 3:57 PM
Safety information
●
According to the USCG, boats under 6.1 m
(20 ft) in length like your watercraft MUST
carry a fire extinguisher of a B-1 classification, with a capacity of two pounds or more
when navigating in waters under USCG jurisdiction. In addition, most state and local
boating laws also require that the fire extinguisher be approved by the USCG.
15
EJU30830
Recommended equipment
The following items should be carried on
board your watercraft:
● Sound-signaling device
You should carry a whistle or other soundsignaling device that can be used to signal
other boats. See “Rules of the Road” for
more information.
● Visual distress signals
It is recommended that a U.S. Coast Guard
approved pyrotechnic device be stored in a
waterproof container on your watercraft. A
mirror can also be used as an emergency
signal. Contact a Yamaha dealer or the
U.S. Coast Guard for more information.
● Watch
A watch is helpful so you will know how long
you have been operating the watercraft.
● Towline
A towline can be used to tow a disabled watercraft in an emergency.
UF1W10E0.book Page 16 Monday, November 26, 2007 3:57 PM
Safety information
EJU36850
EJU30920
Hazard information
●
●
Never start the engine or let it run for any
length of time in an enclosed area. Exhaust
fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of
consciousness and death within a short
time. Always operate the watercraft in an
open area.
Do not touch the hot muffler or engine during or immediately after engine operation;
they can cause serious burns.
Watercraft characteristics
●
●
●
Jet thrust turns the watercraft. Releasing
the throttle lever completely produces only
minimum thrust. If you are traveling at
speeds above trolling, you will have rapidly
decreasing ability to steer without throttle.
This model is equipped with the Yamaha
Engine Management System (YEMS) that
includes an off-throttle steering (OTS) system. It will activate at planing speeds should
you attempt to steer the watercraft after releasing the throttle lever. The OTS system
assists in turning by continuing to supply
some thrust while the watercraft is decelerating, but you can turn more sharply if you
apply throttle while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar
input until you apply throttle again or you
reach trolling speed.
Practice turning in an open area without obstacles until you have a good feel for this
maneuver.
This watercraft is water-jet propelled. The
jet pump is directly connected to the engine.
This means that jet thrust will produce some
movement whenever the engine is running.
There is no “neutral” position. You are in either “forward” or “reverse”, depending upon
the shift lever position.
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or impact the handlebars.
This could increase the risk of back/spinal
injury (paralysis), facial injuries, and broken
legs, ankles, and other bones. You could
also damage the shift mechanism.
16
UF1W10E0.book Page 17 Monday, November 26, 2007 3:57 PM
Safety information
●
●
●
Reverse can be used to slow down or stop
during slow-speed maneuvering, such as
when docking. Once the engine is idling,
shift into reverse and gradually increase engine speed. Make sure that there are no obstacles or people behind you before shifting
into reverse.
Keep away from the intake grate while the
engine is on. Items such as long hair, loose
clothing, or PFD straps can become entangled in moving parts, resulting in severe injury or drowning.
Never insert any object into the jet thrust
nozzle while the engine is running. Severe
injury or death could result from coming in
contact with the rotating parts of the jet
pump.
1 Intake grate
2 Jet thrust nozzle
●
Stop the engine and remove the clip from
the engine shut-off switch before removing
17
any debris or weeds, which may have collected around the jet intake.
2
1
1 Clip
2 Engine shut-off switch
UF1W10E0.book Page 18 Monday, November 26, 2007 3:57 PM
Safety information
EJU30940
Water-skiing
You can use the watercraft for water-skiing if
it has the seating capacity to carry the operator, a rearward-facing spotter, and the waterskier when he or she is not skiing.
The watercraft must also have a cleat designed to pull a ski rope; do not attach the
rope to any other location.
is required by law. Let the skier direct the
operator’s control of speed and direction
with hand signals.
The spotter should sit astride the rear of the
seat and hold onto the handgrip with both
feet firmly on the floor of the footwell for
proper balance while facing to the rear to
1
1 Cleat
It is the watercraft operator’s responsibility to
be alert to the safety of the water-skier and
others. Know and follow all state and local water-skiing regulations in effect for the waters in
which you will be operating.
The operator should be comfortable carrying
passengers before attempting to pull a skier.
The following are some important considerations for minimizing risks while water-skiing.
● The skier should wear an approved PFD,
preferably a brightly colored one so boat
operators can see the skier.
● The skier should wear protective clothing.
Severe internal injuries can occur if water is
forced into body cavities as a result of falling
into the water. Normal swimwear does not
adequately protect against forceful water
entry into the rectum or vagina. The skier
should wear a wetsuit bottom or clothing
that provides equivalent protection.
● A second person should be on board as a
spotter to watch the skier; in most states it
18
UF1W10E0.book Page 19 Monday, November 26, 2007 3:57 PM
Safety information
watch the skier’s hand signals and condition.
●
1 Handgrip
FX SHO
●
●
1 Handgrip
FX Cruiser SHO
1
1 Handgrip
●
●
Your control while pulling a water-skier is
affected by the skier’s ability, as well as water and weather conditions.
When preparing to pull a skier, operate the
watercraft at the slowest possible speed
19
until the watercraft is well away from the skier and slack in the ski rope is taken up.
Make sure that the rope is not looped
around anything.
After checking that the skier is ready and
that there is no traffic or other obstacles, apply enough throttle to raise the skier.
Make smooth, wide turns. The watercraft is
capable of very sharp turns, which could exceed the abilities of the skier. Keep the skier
at least 50 m (150 ft), about twice the distance of a standard ski rope, from any potential hazard.
Be alert to the hazard of the ski rope handle
snapping back at the watercraft when the
skier falls or is unable to get up on the skis.
Towing heavy or bulky objects other than
skiers, such as another boat or watercraft,
can cause loss of steering control and create a hazardous condition. If you must tow
another boat in an emergency situation, operate slowly and cautiously.
UF1W10E0.book Page 20 Monday, November 26, 2007 3:57 PM
Safety information
EJU30960
Rules of the Road
Your Yamaha watercraft is legally considered a powerboat. Operation of the watercraft must be in accordance with the rules
and regulations governing the waterway
on which it is used.
Just as there are rules that apply when you
are driving on streets and highways, there are
waterway rules that apply when you are operating your watercraft. These rules are used internationally, and are also enforced by the
United States Coast Guard and local agencies. You should be aware of these rules, and
follow them whenever you encounter another
vessel on the water.
Several sets of rules prevail according to geographic location, but are all basically the same
as the International Rules of the Road. The
rules presented here in this owner’s/operator’s manual are condensed, and have been
provided for your convenience only. Consult
your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a complete set
of rules governing the waters in which you will
be operating your watercraft.
Steering and sailing rules
Whenever two vessels on the water meet one
another, one vessel has the right-of-way; it is
called the “stand-on” vessel. The vessel that
does not have the right-of-way is called the
“give-way” or “burdened” vessel. These rules
determine which vessel has the right-of-way,
and what each vessel should do.
Stand-on vessel
The vessel with the right-of-way has the duty
to continue its course and speed, except to
avoid an immediate collision. When you maintain your direction and speed, the other vessel
will be able to determine how best to avoid
you.
Give-way vessel
The vessel which does not have the right-ofway has the duty to take positive and timely
action to stay out of the way of the stand-on
vessel. Normally, you should not cross in front
of the vessel with the right-of-way. You should
slow down or change directions briefly and
pass behind the other vessel. You should always move in such a way that the operator of
the other vessel can see what you are doing.
The General Prudential Rule regarding the
right-of-way is that if a collision appears unavoidable, neither boat has the right-of-way.
Both boats must avoid the collision.
In other words, follow the standard rules except when a collision will occur unless both
vessels try to avoid each other. If that is the
case, both vessels become give-way vessels.
Rules when encountering vessels
There are three main situations that you may
encounter with other vessels which could lead
to a collision unless the Steering Rules are followed:
Meeting: you are approaching another vessel
head-on
Crossing: you are traveling across another
vessel’s path
Overtaking: you are passing or being passed
by another vessel
In the following illustration, your watercraft is
in the center. You should give the right-of-way
to any vessels shown in the white area (you
are the give-way vessel). Any vessels in the
shaded area must yield to you (they are the
20
UF1W10E0.book Page 21 Monday, November 26, 2007 3:57 PM
Safety information
give-way vessels). Both you and the meeting
vessel must alter course to avoid each other.
provided the other vessel gives you the rightof-way as it should.
Meeting
If you are meeting another power-driven vessel head on, and are close enough to run the
risk of collision, neither of you has the right-ofway! Both of you should alter course to avoid
an accident. You should keep the other vessel
on your port (left) side. This rule does not apply if both of you will clear one another if you
continue on your set course and speed.
Overtaking
If you are passing another vessel, you are the
give-way vessel. This means that the other
vessel is expected to maintain its course and
speed. You must stay out of its way until you
are clear of it. Likewise, if another vessel is
passing you, you should maintain your speed
and direction so that the other vessel can
steer itself around you.
Other special situations
There are three other rules you should be
aware of when riding your watercraft around
other vessels.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a powerdriven vessel is preparing to go around a
bend that may obstruct the view of other water
vessels, the operator should sound a prolonged blast of four to six seconds on the
whistle. If another vessel is around the bend,
it too should sound the whistle. Even if no reply is heard, however, the vessel should still
proceed around the bend with caution. If you
navigate such waters with your watercraft,
you will need to carry a portable air horn,
available from local marine supply stores.
Crossing
When two power-driven vessels are crossing
each other’s path close enough to run the risk
of collision, the vessel which has the other on
the starboard (right) side must keep out of the
way of the other. If the other vessel is on your
starboard (right) side, you must keep out of its
way; you are the give-way vessel. If the other
vessel is on your port (left) side, remember
that you should maintain course and direction,
21
UF1W10E0.book Page 22 Monday, November 26, 2007 3:57 PM
Safety information
Fishing vessel right-of-way
All vessels fishing with nets, lines, or trawls
are considered to be “fishing vessels” under
the International Rules. Vessels with trolling
lines are not considered fishing vessels. Fishing vessels have the right-of-way regardless
of position. Fishing vessels cannot, however,
impede the passage of other vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the
right-of-way. The exceptions to this are:
(1) When the sailing vessel is overtaking the
power-driven vessel, the power-driven
vessel has the right-of-way.
(2) Sailing vessels should keep clear of any
fishing vessel.
(3) In a narrow channel, a sailing vessel
should not hamper the safe passage of a
power-driven vessel that can navigate
only in such a channel.
Reading buoys and other markers
The waters of the United States are marked
for safe navigation by the lateral system of
buoyage. Simply put, buoys and markers
have an arrangement of shapes, colors, numbers, and lights to show which side of the
buoy a boater should pass on when navigating in a particular direction. The markings on
these buoys are oriented from the perspective
of being entered from seaward (the boater is
going towards the harbor). Red buoys are
passed on your starboard (right) side when
proceeding from open water into the harbor,
and black buoys are to your port (left) side. An
easy way to remember the meaning of the
colors is the phrase “red right returning”.
When navigating out of the harbor, your position with respect to the buoys should be reversed; red buoys should be to port and black
buoys to starboard.
Many bodies of water used by boaters are entirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
This system uses buoys and signs with distinctive shapes and colors to show regulatory
or advisory information. These markers are
white with black letters and orange borders.
22
UF1W10E0.book Page 23 Monday, November 26, 2007 3:57 PM
Safety information
They signify speed zones, restricted areas,
danger areas, and general information.
Remember, markings may vary by geographic location. Always consult local boating authorities before riding your watercraft in
unfamiliar waters.
23
UF1W10E0.book Page 24 Monday, November 26, 2007 3:57 PM
Safety information
EJU30980
To get more boating safety
information
The Online Boating Safety Course:
http://www.boatus.com/onlinecourse/
Be informed about boating safety. Additional
publications and information can be obtained
from many organizations, including the following.
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Affairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647
Other sources
You can find local rules by contacting the National Association of State Boating Law Administrators, or your local Power Squadron.
Watercraft Education and Training
The Online Boating Safety Course, available
through the watercraft section of the yamahamotor.com website, is a free, 50 question
learning course available to the public. Upon
successful completion of 80 percent or better,
the user can request a certificate of completion by mail or can download one immediately. The Online Boating Safety Course,
provided by the Boat/US Foundation, is approved by the National Association of State
Boating Law Administrators (NASBLA) and
recognized by the United States Coast
Guard. This course meets the education requirement for those states that recognize nonproctored, NASBLA-approved courses.
Yamaha is the watercraft industry’s leading
manufacturer to build awareness and support
for boating education. In 1997, Yamaha
launched its GET W.E.T. (Watercraft Education and Training) initiative and has since
reached out to over one million Americans
promoting the benefits of boating education.
24
UF1W10E0.book Page 25 Monday, November 26, 2007 3:57 PM
Safety information
EJU30990
Enjoy your watercraft
responsibly
You share the areas you enjoy when riding
your watercraft with others and with nature.
So your enjoyment includes a responsibility to
treat these other people, and the lands, waters, and wildlife with respect and courtesy.
Whenever and wherever you ride, think of
yourself as the guest of those around you. Remember, for example, that the sound of your
watercraft may be music to you, but it could be
just noise to others. And the exciting splash of
your wake can make waves others won’t enjoy.
Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife areas,
and keep a respectful distance from fishermen, other boats, swimmers, and populated
beaches. When travel in areas like these is
unavoidable, ride slowly and obey all laws.
Proper maintenance is necessary to ensure
that the exhaust emission and sound levels of
your watercraft will continue to be within regulated limits. You have the responsibility to
make sure that the recommended maintenance in this owner’s/operator’s manual is
carried out.
Remember, pollution can be harmful to the
environment. Do not refuel or add oil where a
spill could cause damage to nature. Remove
your watercraft from the water and move it
away from the shoreline before refueling. And
keep your surroundings pleasant for the people and wildlife that share the waterways:
don’t litter!
When you ride responsibly, with respect and
courtesy for others, you help ensure that our
waterways stay open for the enjoyment of a
variety of recreational opportunities.
25
UF1W10E0.book Page 26 Monday, November 26, 2007 3:57 PM
Features and functions
EJU31010
Location of main components
Front view
11
1
2
3
10
4
6
5
7
8
9
1
2
3
4
5
6
7
8
Handlebars
Rear seat
Front seat
Footwell
Sponsons
Gunwale
Pull-up cleat (for FX Cruiser SHO)
Cooling water pilot outlet
9 Bow eye
10 Hood
11 Fuel tank filler cap
26
UF1W10E0.book Page 27 Monday, November 26, 2007 3:57 PM
Features and functions
Rear view
12
11
10
9
8
3
7
6
5
4
1
2
1
2
3
4
5
6
7
8
9
10
11
12
27
Intake grate
Speed sensor
Stern eyes
Stern drain plugs
Reverse gate
Ride plate
Jet thrust nozzle
Reboarding step
Boarding platform
Electric bilge pilot outlet
Cleat
Handgrip
UF1W10E0.book Page 28 Monday, November 26, 2007 3:57 PM
Features and functions
Control system
4
3
10
5
11
2
12
1
9
8
7
6
16 15
14
13
17
20
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Remote control transmitter
Watertight compartment
Start switch
Engine shut-off switch
Clip
Engine stop switch
Engine shut-off cord (lanyard)
Quick Shift Trim System (QSTS) selector
QSTS selector lock lever
Multifunction information center
Beverage holder
Rearview mirrors
Throttle lever
Shift lever
Tilt lever
Glove compartment
17
18
19
20
Up switch (for cruise assist)
Down switch (for cruise assist)
“SET” switch (for cruise assist)
“NO-WAKE MODE” switch
28
UF1W10E0.book Page 29 Monday, November 26, 2007 3:57 PM
Features and functions
Engine compartment
5
2
1
3
4
6
9
7
8
10
1
2
3
4
5
6
7
8
9
10
29
Engine cover
Air filter case
Water separator
Fuel tank
Battery
Flushing hose connector
Electrical box
Engine oil filler cap
Spark plug cap
Dipstick
UF1W10E0.book Page 30 Monday, November 26, 2007 3:57 PM
Features and functions
EJU31021
Operation of controls and other
functions
EJU31040
Seats
To install the rear seat:
Insert the projections on the front of the seat
into the stays on the deck, and then push the
rear of the seat down to lock it in place.
To remove the rear seat:
Pull the rear seat latch up, and then pull the
seat off.
1 Seat latch
To remove the front seat:
(1) Remove the rear seat.
(2) Pull the front seat latch up, and then pull
the seat off.
1 Seat latch
30
UF1W10E0.book Page 31 Monday, November 26, 2007 3:57 PM
Features and functions
To install the front seat:
(1) Insert the projections on the front of the
seat into the stays on the deck, and then
push the rear of the seat down to lock it in
place.
EJU36681
Hood
To open the hood, pull the visor up, and then
lift up the hood.
1
1 Visor
To close the hood, push down on the center
of the hood until it latches securely.
(2) Install the rear seat.
NOTE:
Make sure that the seats are securely installed before operating the watercraft.
NOTE:
Make sure that the hood is securely closed
before operating the watercraft.
EJU36690
Fuel tank filler cap
The fuel tank filler cap is located under the
hood.
To remove the fuel tank filler cap, open the
hood, and then turn the cap counterclockwise.
31
UF1W10E0.book Page 32 Monday, November 26, 2007 3:57 PM
Features and functions
(See page 31 for hood opening and closing
procedures.)
●
1
●
1 Fuel tank filler cap
NOTE:
Make sure that the fuel tank filler cap and the
hood are securely closed before operating the
watercraft.
●
●
EJU34843
Remote control transmitter
The Yamaha Security System and low-RPM
mode settings are selected using the remote
control transmitter. (See “Yamaha Security
System” on page 40 for information on using
the remote control transmitter.)
●
●
Store the remote control transmitter
carefully so it will not be lost. When operating the watercraft, use the transmitter
holder
in
the
watertight
compartment. If you accidentally lose
your remote control transmitter, contact
a Yamaha dealer.
While the remote control transmitter has
been designed for use in wet environments, it should not be operated underwater or submerged for an extended
length of time. If it gets wet, dry it with a
soft, dry cloth.
Keep the remote control transmitter
away from high temperatures and do not
place it in direct sunlight.
Do not drop the remote control transmitter, subject it to strong shocks, or place
any heavy items on it.
Use a soft, dry cloth to clean the transmitter. Do not use detergent, alcohol, or
other chemicals.
If the remote control transmitter needs a
new battery or is not operating properly,
contact a Yamaha dealer. Do not attempt
to replace the battery yourself.
1
ECJ00750
CAUTION:
The Yamaha Security System and lowRPM mode settings can only be selected
using the remote control transmitter. Observe the following precautions to protect
your remote control transmitter:
1 Transmitter holder
NOTE:
●
While the engine is running, input from the
remote control transmitter is not received.
32
UF1W10E0.book Page 33 Monday, November 26, 2007 3:57 PM
Features and functions
●
Refer to local hazardous waste regulations
when disposing of transmitter batteries.
switch, such as if the operator falls off the watercraft.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
3
1
2
ECJ00030
CAUTION:
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to operate the remote control transmitter.
1 Clip
2 Engine shut-off cord
3 Engine shut-off switch
EWJ00010
WARNING
●
EJU31150
Engine stop switch
Push the engine stop switch (red button) to
stop the engine normally.
●
1
1 Engine stop switch
EJU31160
Engine shut-off switch
Insert the clip, on the end of the engine shutoff cord, under the engine shut-off switch
(black button). The engine will stop automatically when the clip is removed from the
33
Always attach the engine shut-off cord
to your left wrist and the clip to the engine shut-off switch BEFORE starting
the engine.
To prevent accidental starting of the engine or unauthorized use by children or
others, always remove the clip from the
engine shut-off switch when the engine
is not running.
UF1W10E0.book Page 34 Monday, November 26, 2007 3:57 PM
Features and functions
EJU36280
EJU36710
Start switch
“SET” switch
Push this switch to activate the cruise assist.
(See page 44 for more information.)
Push the start switch (green button) to start
the engine.
EJU36720
1
Up and down switches
Push these switches to increase or decrease
the engine speed while the cruise assist is operating. (See page 44 for more information.)
EJU36730
“NO-WAKE MODE” switch
Push this switch to activate or deactivate the
no-wake mode. (See page 42 for more information.)
EJU31210
Throttle lever
1 Start switch
Squeeze the throttle lever to increase engine
speed.
NOTE:
The engine will not start when the lock mode
of the Yamaha Security System has been selected, the clip is removed from the engine
shut-off switch, or the throttle lever is
squeezed. (See page 41 for Yamaha Security
System lock and unlock mode selection procedures.)
1
EJU36700
Right handlebar switches
1
1 Throttle lever
Release the throttle lever to decrease engine
speed or to return it to the idle position.
EJU36740
Cooling water pilot outlets
2
3
This watercraft is equipped with cooling water
pilot outlets on the port (left) and starboard
(right) sides of the watercraft.
4
1
2
3
4
Up switch
Down switch
“SET” switch
“NO-WAKE MODE” switch
34
UF1W10E0.book Page 35 Monday, November 26, 2007 3:57 PM
Features and functions
When the engine is running, cooling water is
circulated in the engine, and then it is discharged from the pilot outlets.
To check for proper operation of the cooling
system, check that water is being discharged
from the port (left) pilot outlets. If water is not
being discharged from these outlets, cooling
water may not be circulating in the engine.
When this occurs, stop the engine and check
for the cause. (See pages 51 and 106 for
more information.)
NOTE:
●
●
If the cooling water passages are dry, it will
take about 60 seconds for the water to
reach the outlets after the engine is started.
Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.
35
EJU31260
Steering system
Your watercraft can be steered by turning the
handlebars in the direction you wish to travel.
1 Handlebar
2 Jet thrust nozzle
When the handlebars are turned, the angle of
the jet thrust nozzle is changed, and the direction of the watercraft is changed accordingly.
Since the strength of the jet thrust determines
the speed and degree of a turn, throttle must
always be applied when attempting a turn, except at trolling speed.
This model is equipped with the Yamaha Engine Management System (YEMS) that includes an off-throttle steering (OTS) system.
It will activate at planing speeds should you
attempt to steer the watercraft after releasing
the throttle lever. The OTS system assists in
turning by continuing to supply some thrust
while the watercraft is decelerating, but you
can turn more sharply if you apply throttle
while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
UF1W10E0.book Page 36 Monday, November 26, 2007 3:57 PM
Features and functions
Once the engine slows down, the watercraft
will no longer turn in response to handlebar input until you apply throttle again or you reach
trolling speed.
EJU31290
otherwise the handlebars may suddenly
change position, which may lead to an
accident.
EJU36750
Shift lever
Tilt lever
The tilt lever is located in front of the glove
compartment and is used to adjust the tilt of
the handlebars.
The shift lever is located on the starboard
(right) side of the watercraft and is used to
control the reverse gate, which allows the watercraft to move in reverse or forward.
1
1
3 2
1 Tilt lever
To adjust the tilt, pull the tilt lever up, and then
move the handlebars up or down to the desired position.
1 Shift lever
2 Forward position
3 Reverse position
When the shift lever is in the reverse position,
the watercraft can be launched from a trailer,
or backed up out of tight spots where you cannot turn around easily.
To shift into reverse:
(1) Release the throttle lever and let the engine speed return to idle.
(2) Pull the shift lever toward you until it
stops.
EWJ00030
WARNING
EWJ00040
WARNING
●
●
Never touch the tilt lever during operation, otherwise the handlebars may suddenly change position, which may lead
to an accident.
Make sure that the tilt lever returns to its
original position and that the handlebars
are locked in place after adjusting them,
●
●
Make sure that the throttle lever is completely released and that the engine is at
idle before shifting into reverse.
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.
36
UF1W10E0.book Page 37 Monday, November 26, 2007 3:57 PM
Features and functions
●
●
●
Use reverse for slow-speed maneuvering only.
Make sure that there are no obstacles or
people behind you before shifting into
reverse.
Do not touch the reverse gate while the
shift lever is being operated, otherwise
you could be pinched.
EJU31311
Quick Shift Trim System (QSTS)
selector
The QSTS selector is located at the left handlebar grip and is used to adjust the trim angle
of the watercraft.
NOTE:
This model is equipped with a function which
limits the engine speed in reverse.
To shift into forward:
(1) Release the throttle lever and let the engine speed return to idle.
(2) Push the shift lever away from you until it
stops.
1 Quick Shift Trim System (QSTS) selector
2 QSTS selector lock lever
Operating the QSTS selector changes the angle of the jet thrust nozzle vertically. This
changes the trim angle of the watercraft.
37
UF1W10E0.book Page 38 Monday, November 26, 2007 3:57 PM
Features and functions
There are 5 positions: 2 bow-down positions
(a) and (b), neutral “N”, and 2 bow-up positions (c) and (d).
To enhance particular types of performance,
select bow down or bow up.
EJU31330
To change the trim angle:
(1) Reduce engine speed to less than 3000
r/min.
(2) Squeeze the QSTS selector lock lever,
and then turn the QSTS selector to the
desired position.
(3) Release the lock lever to lock the QSTS
selector.
ECJ00011
CAUTION:
Do not turn the QSTS selector while operating the watercraft at an engine speed of
3000 r/min or more, otherwise damage
could occur to the QSTS.
The neutral “N” position will provide good performance for most operating conditions.
Bow down
Turn the QSTS selector to (a) or (b) and the
bow will go down while the watercraft is on
plane.
Bow down puts more of the bow in the water.
This gives the watercraft more “hook”, which
enhances turning performance. This position
will also help the watercraft get up on plane
more quickly.
At higher speeds, however, the watercraft will
have a greater tendency to “bow steer” and
follow waves and wakes in the water. Fuel
economy and maximum speed are also reduced.
EJU31340
Bow up
Turn the QSTS selector to (c) or (d) and the
bow will go up while the watercraft is on plane.
Bow up puts less of the bow in the water.
There is less water resistance, so straight-
38
UF1W10E0.book Page 39 Monday, November 26, 2007 3:57 PM
Features and functions
ahead acceleration when on plane and top
speed are enhanced.
In some conditions, however, the watercraft
may tend to “porpoise” (hop in the water). If
the watercraft is porpoising, select neutral or
bow down.
EJU34861
Reboarding step
The reboarding step provides a handhold and
footstep for boarding the watercraft.
1
EJU31360
Handgrip
The handgrip provides a handhold for boarding the watercraft and for a spotter when facing rearward.
FX SHO
1 Reboarding step
EWJ01210
WARNING
Do not use the reboarding step to lift the
watercraft. The watercraft could fall, which
could result in severe injury.
ECJ00741
1 Handgrip
CAUTION:
FX Cruiser SHO
1
Use the reboarding step only to board the
watercraft in the water. Do not use the reboarding step as a footstep when the watercraft is on land, or for any other
purpose. The watercraft can be damaged.
EJU34870
Bow eye
The bow eye is located at the bow of the watercraft.
1 Handgrip
EWJ00020
WARNING
Do not use the handgrip to lift the watercraft. The watercraft could fall, which
could result in severe injury.
39
UF1W10E0.book Page 40 Monday, November 26, 2007 3:57 PM
Features and functions
The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or
towing it in an emergency.
To use a pull-up cleat, pull it up.
1
1 Pull-up cleat
EWJ00820
1 Bow eye
EJU34880
Stern eyes
The stern eyes are located at the stern of the
watercraft.
The stern eyes are used to attach a rope to
the watercraft when transporting or mooring it.
WARNING
Do not use the pull-up cleats to lift the watercraft. The watercraft could fall, which
could result in severe injury.
EJU31370
Yamaha Engine Management System
(YEMS)
This model is equipped with an integrated,
computerized management system that controls and adjusts ignition timing, fuel injection,
engine diagnostics, and the off-throttle steering (OTS) system.
EJU36760
Yamaha Security System
1
1 Stern eye
EJU34890
Pull-up cleats (for FX Cruiser SHO)
The pull-up cleats are used to attach a rope to
the watercraft when mooring it.
The Yamaha Security System functions to
help prevent unauthorized use or theft of the
watercraft. The engine cannot be started if the
security system is in the lock mode. The engine can only be started in the unlock mode.
The lock and unlock modes of the security
system are selected using the remote control
transmitter that is included with this watercraft.
NOTE:
Since the watercraft is programmed to recognize the internal code from this transmitter
only, the security system setting can only be
changed with this transmitter. If you lose the
remote control transmitter or if it does not op-
40
UF1W10E0.book Page 41 Monday, November 26, 2007 3:57 PM
Features and functions
erate properly, contact a Yamaha dealer.
(See page 32 for operation of the remote control transmitter.)
1 Remote control transmitter
Depending on the selected Yamaha Security
System setting, the “UNLOCK” indicator light
will come on or go off.
1 Lock button
2 Unlock button
EJU36770
Yamaha Security System settings
The Yamaha Security System settings are selected by pressing the lock or unlock button
on the remote control transmitter briefly.
1 “UNLOCK” indicator light
NOTE:
The lock and unlock modes of this system can
only be selected while the engine is stopped.
LOCK
When the lock button on the remote control
transmitter is pressed briefly, the beeper
sounds once and the “UNLOCK” indicator
light goes off. This indicates the lock mode is
selected and the engine cannot be started.
UNLOCK
When the unlock button on the remote control
transmitter is pressed briefly, the beeper
sounds two or three times and the “UNLOCK”
indicator light comes on. This indicates the
41
UF1W10E0.book Page 42 Monday, November 26, 2007 3:57 PM
Features and functions
unlock mode is selected and the engine can
be started.
NOTE:
The beeper sounds two times for the normal
mode or three times for the low-RPM mode.
(See the items in “Selecting the operation
mode” for operation mode information.)
Number of
beeps
Yamaha Security
System mode
Engine
can be
started
Lock
NO
Unlock
(normal mode)
YES
Unlock
(low-RPM mode)
YES
Low-RPM mode
Maximum engine speed (r/min) in this mode is
limited to approximately 70% of the maximum
engine speed in the normal mode.
If the beeper sounds three times, the lowRPM mode is activated and the “L-MODE” indicator light comes on.
EJU36780
Selecting the operation mode
There are two operation modes in the unlock
mode of the Yamaha Security System: the
normal mode and the low-RPM mode. The
normal mode and low-RPM mode can only be
selected when the engine is stopped in the
unlock mode. Press the unlock button on the
remote control transmitter for more than 4
seconds to switch between the normal mode
and the low-RPM mode.
Normal mode
The watercraft can be ridden normally in this
mode.
If the beeper sounds two times, the normal
mode is activated.
1 “L-MODE” indicator light
NOTE:
If neither the start switch nor the remote control transmitter is operated within 25 seconds
after the unlock button is pressed to select the
unlock mode, the multifunction information
center will turn off and enter a standby state.
If the multifunction information center is in the
standby state, start the engine to return the
display and the indicator lights to their state
before the center turned off.
EJU37011
No-wake mode
The no-wake mode is a function that maintains the engine speed at a fixed setting for
operating the watercraft at low speeds. This
function can be used only for forward operation of the watercraft.
Activating and deactivating the no-wake
mode
Activation of the no-wake mode will be confirmed by the beeper and the digital speedometer display.
42
UF1W10E0.book Page 43 Monday, November 26, 2007 3:57 PM
Features and functions
Number
of beeps
Digital
No-wake mode operspeedomeation
ter display
Activated
Starts
flashing
Deactivated
Stops
flashing
vated, the beeper sounds three times
quickly and “5” (when miles are selected)
or “8” (when kilometers are selected)
starts flashing in the digital speedometer
display. Keep the throttle lever in the idle
position when the no-wake mode is activated.
NOTE:
NOTE:
The beeps and the flashing digital speedometer display also indicate the activation of the
cruise assist. (See page 44 for more information.)
The digital speedometer display flashes continually while the no-wake mode is activated.
To activate the no-wake mode:
NOTE:
The no-wake mode cannot be activated immediately after starting the engine. After starting the engine, wait for 5 seconds or more
before activating the mode.
(1) Release the throttle lever.
(2) Check that the shift lever is in the forward
position.
1
1 “NO-WAKE MODE” switch
1
2
1 Shift lever
2 Forward position
NOTE:
The no-wake mode cannot be activated when
the shift lever is in the reverse position.
(3) Push and hold the “NO-WAKE MODE”
switch. When the no-wake mode is acti-
43
To deactivate the no-wake mode:
Perform one of the following procedures. The
beeper sounds two times quickly and the digital speedometer display stops flashing when
the no-wake mode is deactivated.
● Push the “NO-WAKE MODE” switch.
● Squeeze the throttle lever.
UF1W10E0.book Page 44 Monday, November 26, 2007 3:57 PM
Features and functions
NOTE:
The no-wake mode is also deactivated when
the engine is stopped.
EJU37021
Cruise assist
The cruise assist is a function for maintaining
a desired engine speed within a fixed range
while operating the watercraft.
Activating and deactivating the cruise assist
Activation of the cruise assist will be confirmed by the beeper and the digital speedometer display.
Number
of beeps
Digital
Cruise assist operaspeedometion
ter display
Activated
Starts
flashing
Deactivated
Stops
flashing
Engine speed increases or decreases
Continues
flashing
switch. When the cruise assist is activated, the beeper sounds three times quickly and the digital speedometer display
starts flashing. To keep the cruise assist
activated, be sure to keep the throttle lever squeezed further than the position at
which the cruise assist was set; releasing
the throttle lever will deactivate the cruise
assist.
NOTE:
The digital speedometer display flashes continually while the cruise assist is activated.
Make sure that the beeper has sounded and
the digital speedometer display is flashing before squeezing the throttle lever to the full
throttle position. If the speedometer display is
not flashing, the cruise assist is not activated
NOTE:
The beeps and the flashing digital speedometer display also indicate the activation of the
no-wake mode. (See page 42 for more information.)
To activate the cruise assist:
(1) Operate the throttle lever until the desired
engine speed is reached.
NOTE:
●
●
The cruise assist can only be set between
engine speeds of approximately 3000 r/min
and approximately 7000 r/min.
The cruise assist cannot be activated in the
low-RPM mode. (See the items in 42 for operation mode information.)
(2) Once the engine speed reaches the desired cruise assist setting, push the “SET”
44
UF1W10E0.book Page 45 Monday, November 26, 2007 3:57 PM
Features and functions
and the engine will respond normally to the
throttle.
1
2
3
beeper will sound one time quickly and the
engine speed will change. However, the adjustment is limited to a maximum of five increments above or below the initial cruise assist
setting.
To deactivate the cruise assist:
Relax your grip on the throttle lever. The
beeper sounds two times quickly and the digital speedometer display stops flashing when
the cruise assist is deactivated.
1 Up switch
2 Down switch
3 “SET” switch
NOTE:
The cruise assist is also deactivated when the
engine is stopped.
EJU34902
Multifunction information center
The multifunction information center is
equipped with the following three main com-
NOTE:
Once the cruise assist is activated, the engine
speed can be increased by pushing the up
switch or decreased by pushing the down
switch. Each time a switch is pushed, the
45
UF1W10E0.book Page 46 Monday, November 26, 2007 3:57 PM
Features and functions
ponents for help and convenience in operating the watercraft.
1 Analog speedometer/tachometer and indicator lights
2 Left multifunction display and operation buttons
3 Right multifunction display and operation
buttons (for FX Cruiser SHO)
ECJ00072
CAUTION:
Do not run the engine for more than 15
seconds without supplying water or over
4000 r/min when checking the operation of
the meter on land, otherwise the engine
could overheat.
NOTE:
●
●
When the multifunction information center
starts operating, the analog speedometer/tachometer makes one sweep, all displays light up for 2 seconds, and then the
meter starts to operate normally.
The multifunction information center will
continue to operate for 25 seconds after the
engine stops.
EJU34930
Analog speedometer/tachometer and indicator lights
This watercraft is equipped with the following
meter and indicator lights.
1
2
3
4
5
6
Analog speedometer/tachometer
“SPEED” indicator light
“WARNING” indicator light
“RPM” indicator light
“UNLOCK” indicator light
“L-MODE” indicator light
EJU36790
Analog speedometer/tachometer
The analog speedometer/tachometer can be
used as a speedometer or a tachometer.
To switch between the speedometer and the
tachometer functions, push the “Speed/RPM”
button for at least 1 second when the multifunction information center is operating.
The “SPEED” indicator light comes on when
the analog speedometer is selected. The
46
UF1W10E0.book Page 47 Monday, November 26, 2007 3:57 PM
Features and functions
“RPM” indicator light comes on when the analog tachometer is selected.
1 “Speed/RPM” button
2 “SPEED” indicator light
3 “RPM” indicator light
NOTE:
The “SPEED” indicator light blinks three
times, then comes on, if miles are selected as
the display units when the analog speedometer/tachometer is switched to the speedometer function.
Analog speedometer
The analog speedometer shows the watercraft speed against water.
The large inner numbers on the meter show
the watercraft speed in miles per hour (mph)
and the small outer numbers show the speed
in kilometers per hour (km/h) when the speedometer function is selected.
Analog tachometer
The analog tachometer shows the engine
speed.
The large inner numbers on the meter show
the engine speed (× 100 r/min) when the tachometer function is selected.
EJU36800
“SPEED” indicator light
The “SPEED” indicator light comes on when
the analog speedometer is selected.
1 “SPEED” indicator light
The “SPEED” indicator light blinks three times
in the following instances:
● The analog speedometer/tachometer is
switched to the speedometer function when
miles are selected as the display units.
● The display units of the multifunction information center are switched to miles from kilometers.
● Miles are selected as the display units when
the multifunction information center starts
operating.
EJU34960
“RPM” indicator light
The “RPM” indicator light comes on when the
analog tachometer is selected.
1 “RPM” indicator light
47
UF1W10E0.book Page 48 Monday, November 26, 2007 3:57 PM
Features and functions
EJU34980
EJU35010
“WARNING” indicator light
The “WARNING” indicator light blinks or
comes on, together with a warning indicator,
when a malfunction has occurred.
“L-MODE” indicator light
The “L-MODE” indicator light comes on when
the low-RPM mode is selected. (See page 42
for more information.)
1 “WARNING” indicator light
1 “L-MODE” indicator light
EJU34990
EJU35021
“UNLOCK” indicator light
The “UNLOCK” indicator light comes on when
the unlock mode of the Yamaha Security System is selected. The watercraft can be ridden
normally when this light is on. (See page 41
for more information.)
Left multifunction display and operation
buttons
The left multifunction display is equipped with
the following functions.
1 “UNLOCK” indicator light
1
2
3
4
5
6
7
Fuel level meter
Fuel level warning indicator
Hour meter/voltmeter
Digital speedometer
Oil pressure warning indicator
Check engine warning indicator
Engine overheat warning indicator
48
UF1W10E0.book Page 49 Monday, November 26, 2007 3:57 PM
Features and functions
The following operation buttons are on the left
side of the multifunction information center.
1 “Speed/RPM” button
2 “Volt/Hour” button
●
Kilometers are selected as the display units
at the Yamaha factory.
1 “Volt/Hour” button
EJU37080
Digital speedometer
The digital speedometer shows the watercraft
speed against water.
1 “SPEED” indicator light
EJU31511
1 Digital speedometer
NOTE:
●
●
To switch the speedometer display between kilometers and miles, push the
“Volt/Hour” button for at least 1 second,
within 10 seconds after the multifunction information center starts operating.
The “SPEED” indicator light blinks three
times if miles are selected as the display
units when the multifunction information
center starts operating, or if the display
units are switched to miles.
49
Fuel level meter
The fuel level meter is provided for convenient
fuel level checking while riding.
UF1W10E0.book Page 50 Monday, November 26, 2007 3:57 PM
Features and functions
The fuel level meter has eight segments
which show the amount of fuel remaining in
the fuel tank.
1 Fuel level meter
NOTE:
The fuel level is most accurate when the watercraft is sitting level on a trailer or in the water.
EJU35060
Hour meter/voltmeter
NOTE:
To switch the display between the hour meter
and the voltmeter, push the “Volt/Hour” button
for at least 1 second after the meter is displayed for more than 10 seconds.
1 Hour meter/voltmeter
2 “Volt/Hour” button
Hour meter
The hour meter is provided to make it easy to
follow the maintenance schedule.
The meter shows the hours of engine operation that have elapsed since the watercraft
was new.
Voltmeter
The voltmeter is provided to display the voltage of the battery.
When the battery voltage is normal, the voltmeter displays approximately 12 volts.
If the battery voltage is less than 8.0 volts,
“LO” is displayed on the voltmeter and if the
voltage is above 18.1 volts, “HI” is displayed
on the voltmeter. If “HI” or “LO” is displayed,
return to shore and, if necessary, have a
Yamaha dealer check the charging system
and the battery.
EJU36810
Fuel level warning indicator
If the fuel remaining in the fuel tank drops to
about 18 L (4.8 US gal, 4.0 Imp.gal), the lowest two fuel level segments, the fuel level
warning indicator, and the “WARNING” indicator light begin to blink. The buzzer also
starts sounding intermittently.
If this occurs, refill the fuel tank as soon as
possible.
The warning signals will be cleared when the
engine is restarted after the fuel tank is refilled.
NOTE:
Press any button on the multifunction information center to stop the buzzer.
50
UF1W10E0.book Page 51 Monday, November 26, 2007 3:57 PM
Features and functions
EJU35122
Oil pressure warning indicator
If the oil pressure does not rise to specification, the “WARNING” indicator light and the oil
pressure warning indicator begin to blink, and
the buzzer sounds intermittently. At the same
time, the engine speed is limited to help prevent damage.
If this occurs, reduce the engine speed, return
to shore, and then check the engine oil level.
(See page 63 for engine oil level checking
procedures.) If the oil level is low, add enough
engine oil to raise it to the proper level. If the
oil level is sufficient, have a Yamaha dealer
check the watercraft.
sounds, the engine speed is limited to help
prevent damage.
If this occurs, immediately reduce the engine
speed, return to shore, and then check for water discharge at the port (left) cooling water pilot outlets while the engine is running. If there
is no discharge of water, shut the engine off,
and then check the intake grate and impeller
for clogging.
NOTE:
Press any button on the multifunction information center to stop the buzzer.
EJU36820
Engine overheat warning indicator
This model is equipped with an engine overheat warning system.
If the engine starts to overheat, the “WARNING” indicator light and the engine overheat
warning indicator blink, and then come on.
The buzzer also begins to sound intermittently, and then it sounds continuously. After the
light and indicator start to blink and the buzzer
51
EWJ00050
WARNING
Before attempting to remove weeds or debris from the intake grate or impeller, shut
the engine off and remove the clip from the
engine shut-off switch. Severe injury or
UF1W10E0.book Page 52 Monday, November 26, 2007 3:57 PM
Features and functions
death could result from coming in contact
with the rotating parts of the jet pump.
check engine warning indicator begin to blink,
and the buzzer sounds intermittently.
If this occurs, reduce the engine speed, return
to shore, and have a Yamaha dealer check
the engine.
NOTE:
Press any button on the multifunction information center to stop the buzzer.
EJU35033
ECJ00040
CAUTION:
If you cannot locate and correct the cause
of the overheating, consult a Yamaha dealer. Continuing to operate at higher speeds
could result in severe engine damage.
NOTE:
Press any button on the multifunction information center to stop the buzzer.
Right multifunction display and operation
buttons (for FX Cruiser SHO)
The right multifunction display shows the following information.
● Compass
● Average speed
● Tripmeter
● Trip timer
● Fuel consumption per hour
● Fuel consumption per kilometer/mile
● Water temperature
● Air temperature
EJU35131
Check engine warning indicator
If a sensor malfunction or a short circuit is detected, the “WARNING” indicator light and the
52
UF1W10E0.book Page 53 Monday, November 26, 2007 3:57 PM
Features and functions
The following operation buttons are on the
right side of the multifunction information center.
1 “Mode/Reset” button
2 “Start/Stop” button
To switch the display mode, push the
“Mode/Reset” button for less than 1 second.
The display mode changes in the following order.
Compass → Average speed → Tripmeter →
Trip timer → Fuel consumption per hour →
Fuel consumption per kilometer/mile → Water
temperature → Air temperature
ating, or if the display units are switched to
miles/gallons/degrees Fahrenheit.
1 “Volt/Hour” button
2 “SPEED” indicator light
Compass
This display shows the current direction of the
watercraft using the 8 major compass points.
NOTE:
●
●
To switch the display units between kilometers/liters/degrees Celsius and miles/gallons/degrees
Fahrenheit,
push
the
“Volt/Hour” button for at least 1 second,
within 10 seconds after the multifunction information center starts operating.
The “SPEED” indicator light blinks three
times if miles/gallons/degrees Fahrenheit
are selected as the display units when the
multifunction information center starts oper-
53
NOTE:
The accuracy of the compass varies depending on the operating conditions. Use this function as a reference only.
UF1W10E0.book Page 54 Monday, November 26, 2007 3:57 PM
Features and functions
Average speed
This display shows the average speed in
miles per hour “AV MPH” or kilometers per
hour “AV KMH” since it was reset.
Fuel consumption per hour
This display shows the current fuel consumption in gallons per hour “G/HR” or liters per
hour “L/HR”.
Tripmeter
This display shows the distance traveled in
miles “MILES” or kilometers “KM” since it was
reset.
Fuel consumption per kilometer/mile
This display shows the current fuel consumption in gallons per mile “G/MILE” or liters per
kilometer “L/KM”.
Trip timer
This display shows the hours of operation
“TRIPTM” since it was reset.
NOTE:
The actual fuel consumption varies depending on the operating conditions. Use this function as a reference only.
54
UF1W10E0.book Page 55 Monday, November 26, 2007 3:57 PM
Features and functions
Water temperature
This display shows the ambient water temperature “L TEMP” (lake temperature).
Air temperature
This display shows the ambient air temperature “E TEMP” (environmental temperature).
surements are stopped. The beeper sounds
twice.
1 “Mode/Reset” button
2 “Start/Stop” button
NOTE:
●
●
The displays can be reset only when the
measurements are stopped.
The measurements are not saved if the engine is stopped. The displays are reset automatically when they go off 25 seconds
after the engine stops.
EJU35141
Storage compartments
Average speed/Tripmeter/Trip timer
modes
Average speed, distance traveled, and trip
time are recorded once measurements have
started, regardless of the current display.
To start the measurements, push the
“Start/Stop” button for less than 1 second.
The beeper sounds once.
To stop the measurements, push the
“Start/Stop” button for less than 1 second.
The beeper sounds once. To restart the measurements, push the “Start/Stop” button for
less than 1 second. The beeper sounds once.
To reset the displays, push the “Mode/Reset”
button for at least 2 seconds while the mea-
55
A front storage compartment, glove compartment, seat storage compartment, watertight
compartment, and beverage holder are provided.
NOTE:
●
●
Make sure that the storage compartments
are closed securely before operating the
watercraft.
The front storage compartment, glove compartment, and seat storage compartment
are not designed to be watertight. If you carry objects that must be kept dry, such as the
manuals, put them in a waterproof bag or
the watertight compartment.
UF1W10E0.book Page 56 Monday, November 26, 2007 3:57 PM
Features and functions
EJU36831
Front storage compartment
The front storage compartment is located at
the bow.
To open the front storage compartment, pull
the visor up, and then lift up the hood.
To close the front storage compartment, push
down on the center of the hood until it latches
securely.
1
NOTE:
Make sure that the front storage compartment
is securely closed before operating the watercraft.
1 Visor
EJU35161
Glove compartment
The glove compartment is located in front of
the seat.
1
1 Front storage compartment
Front storage compartment:
Capacity:
66.0 L (17.4 US gal) (14.5 Imp.gal)
Load limit:
5.0 kg (11 lb)
56
UF1W10E0.book Page 57 Monday, November 26, 2007 3:57 PM
Features and functions
To open the glove compartment, turn the
glove compartment knob, and then lift up the
lid.
To open the seat storage compartment, remove the rear seat. (See page 30 for rear seat
removal and installation procedures.)
1
1 Glove compartment knob
1
1 Seat storage compartment
1 Glove compartment
Glove compartment:
Capacity:
5.9 L (1.6 US gal) (1.3 Imp.gal)
Load limit:
1.0 kg (2 lb)
To close the glove compartment, lower the lid,
and then turn the glove compartment knob to
lock the lid in place.
EJU31760
Seat storage compartment
The seat storage compartment is located under the rear seat.
57
Seat storage compartment:
Capacity:
15.0 L (4.0 US gal) (3.3 Imp.gal)
Load limit:
9.0 kg (20 lb)
UF1W10E0.book Page 58 Monday, November 26, 2007 3:57 PM
Features and functions
EJU35170
Beverage holder
The beverage holder is located on the starboard (right) side of the watercraft.
1
NOTE:
Make sure that the watertight compartment
cap is closed securely before operating the
watercraft.
1 Beverage holder
NOTE:
Do not place beverages in the beverage holder when operating the watercraft.
EJU35183
Watertight compartment
The watertight compartment is located on the
port (left) side of the watercraft.
To open the watertight compartment, turn the
cap counterclockwise.
1
2
1 Watertight compartment cap
2 Watertight compartment
Watertight compartment:
Capacity:
2.7 L (0.7 US gal, 0.6 Imp.gal)
Load limit:
1.0 kg (2.2 lb)
58
UF1W10E0.book Page 59 Monday, November 26, 2007 3:57 PM
Operation
EJU31820
Fuel and oil
This watercraft is equipped with a 4-stroke engine. Conventional 2-stroke engine oil cannot
be used.
The engine utilizes an electronic fuel injection
system to deliver the optimal air-fuel ratio required by the engine. By ensuring the optimal
combustion conditions, this system is able to
increase startability and improve fuel economy.
EJU31842
Gasoline
EWJ00281
WARNING
GASOLINE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE!
● Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.
● Stop the engine before refueling.
● Refuel in a well-ventilated area with the
watercraft in a horizontal position.
● Do not stand or sit on the watercraft
while refueling.
● Take care not to spill gasoline. If gasoline spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.
● Avoid overfilling the fuel tank. Stop filling when the fuel level reaches approximately 50 mm (2 in) from the top of the
fuel tank. Fuel expands as it warms up
and could overflow if the fuel tank has
been overfilled. If temporarily leaving
the watercraft with a full fuel tank, do not
leave it in direct sunlight. Leave it in a
well-ventilated area with the watercraft
in a horizontal position.
● Tighten the fuel tank filler cap securely
after refueling.
59
●
●
If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical
attention.
If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
ECJ00310
CAUTION:
Use only fresh gasoline that has been
stored in clean containers.
Recommended gasoline:
Regular unleaded gasoline with a minimum octane rating of
86 (Pump octane number) = (R +
M)/2
90 (Research octane number)
EJU31860
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets the minimum octane ratings.
Gasohol containing methanol is not recommended by Yamaha because it can cause
fuel system damage and engine performance
problems.
UF1W10E0.book Page 60 Monday, November 26, 2007 3:57 PM
Operation
EJU35613
Engine oil
Use a combination of the recommended SAE
and API engine oil classifications.
ly 50 mm (2 in) from the top of the fuel
tank as indicated in the illustration.
ECJ00280
CAUTION:
Use only 4-stroke engine oil.
EJU36860
Filling the fuel tank
ECJ00290
CAUTION:
Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.
(1) Remove the seats, and check the fuel
level. (See page 30 for seat removal and
installation procedures.)
(2) Open the hood. (See page 31 for hood
opening and closing procedures.)
(3) Remove the fuel tank filler cap, and then
slowly add fuel to the fuel tank. Stop filling
when the fuel level reaches approximate-
1
1 Approximately 50 mm (2 in) from top of the
fuel tank
(4) Install the fuel tank filler cap, and then
close the hood and install the seats.
Fuel tank capacity:
70 L (18.5 US gal) (15.4 Imp.gal)
60
UF1W10E0.book Page 61 Monday, November 26, 2007 3:57 PM
Operation
EJU31980
Pre-operation checks
EJU31990
Pre-operation check list
Before operating this watercraft, perform the checks in the following check list. See the accompanying text in this chapter for details on how to perform the checks.
EWJ00410
WARNING
If any item in the pre-operation check list is not working properly, have it inspected and
repaired before operating the watercraft, otherwise an accident could occur.
ITEM
ROUTINE
PAGE
Engine compartment
Remove the seats to ventilate the engine compartment. Check for fuel vapors and loose electrical connections.
63
Bilge
Check for water and fuel and drain if necessary.
65
Stern drain plugs
Check for proper installation.
66
Throttle lever
Check that the throttle lever springs back smoothly.
67
Steering system
Check for proper operation.
Check that the handlebars are locked in place.
67
Shift lever and reverse gate
Check for proper operation.
68
QSTS
Check for proper operation.
69
Fuel and oil
Check the fuel and oil levels and replenish if necessary.
Check the hoses and tanks for leakage.
Water separator
Check for water and drain if necessary.
64
Battery
Check the electrolyte level and battery condition.
66
Hood
Check that the hood is securely closed.
31
Front and rear seats
Check that the seats are securely installed.
30
Hull and deck
Check the hull and deck for cracks and other damage.
63
Jet intake
Check for debris and remove if necessary.
69
Fire extinguisher
Check the condition and replace if necessary.
67
Engine shut-off cord
Check the condition and replace if frayed or broken.
70
Switches
Check the start switch, engine stop switch, and engine shut-off switch for proper operation.
70
Cooling water pilot outlet
Check that water is discharged while the engine is
running and the watercraft is in the water.
70
Multifunction information
center
Check for warning indications and proper operation.
71
BEFORE LAUNCH OR OPERATION
63, 63
AFTER LAUNCH
61
UF1W10E0.book Page 62 Monday, November 26, 2007 3:57 PM
Operation
NOTE:
Pre-operation checks should be made each time the watercraft is used. These checks can be
completed in a short time. It is worth the time spent to ensure safety and reliability.
62
UF1W10E0.book Page 63 Monday, November 26, 2007 3:57 PM
Operation
EJU32280
Pre-operation check points
EJU32330
Engine compartment
Ventilate the engine compartment before
each use.
To ventilate the engine compartment, remove
the seats. (See page 30 for seat removal and
installation procedures.) Leave the engine
compartment open for a few minutes to allow
any fuel vapors to escape.
While the engine compartment is open, check
for loose electrical connections.
page 31 for hood opening and closing
procedures.)
(2) Remove the seats. (See page 30 for seat
removal and installation procedures.)
(3) Check the fuel level in the fuel tank and
replenish if necessary. (See page 60 for
filling procedures.)
(4) Install the fuel tank filler cap, and then
close the hood and install the seats.
EJU36881
Engine oil level
Check the engine oil level before each use.
ECJ01000
CAUTION:
●
●
EWJ00460
WARNING
Failure to ventilate the engine compartment could result in a fire or explosion. Do
not start the engine if there is a fuel leak or
a loose electrical connection.
EJU32350
Hull and deck
Check the hull and deck for cracks and other
damage. If any damage is found, have a
Yamaha dealer repair the watercraft.
EJU36870
Fuel level
Check the fuel system for leakage, cracks,
and malfunctions before each use. (See page
93 for check points and correct procedures.)
(1) Open the hood and remove the fuel tank
filler cap to release any pressure that
might have built up in the fuel tank. (See
63
Make sure that the engine has enough
oil, but do not overfill it. If there is too little oil, the engine can be damaged. If
there is too much oil, the air filter can become saturated with oil, permanently
damaging the filter and reducing engine
performance. Follow the checking procedure carefully.
Make sure that debris and water do not
enter the oil filler hole. Debris and water
in the engine oil can cause serious engine damage.
To check the engine oil level:
(1) Place the watercraft in a precisely level
position on land with the engine stopped.
NOTE:
If the engine was running, allow the engine oil
to settle by waiting 5 minutes or more before
checking the oil level.
(2) Remove the seats. (See page 30 for seat
removal and installation procedures.)
(3) Remove the dipstick, wipe it clean, and
then insert it back into the dipstick tube
completely. Remove the dipstick again
and check that the engine oil level is be-
UF1W10E0.book Page 64 Monday, November 26, 2007 3:57 PM
Operation
tween the minimum and maximum level
marks.
(5) Remove the engine oil filler cap.
1
1
1 Engine oil filler cap
1 Dipstick
2
(6) Pour engine oil into the filler hole. Wait
approximately 5 minutes until the engine
oil settles.
1
1 Maximum level mark
2 Minimum level mark
(4) If the engine oil level is below the minimum level mark, perform steps 5–7 to
add enough oil so that the oil level is between the minimum and maximum level
marks on the dipstick. If the engine oil level is significantly above the maximum level mark, have a Yamaha dealer service
the watercraft.
NOTE:
The difference between the minimum and
maximum level marks on the dipstick is equal
to approximately 1 liter of engine oil.
(7) Repeat steps 3–6 until the engine oil is at
the proper level.
(8) Install the engine oil filler cap, and then
install the seats.
EJU32420
Water separator
Check the water separator for water. The water separator retains any water that may have
entered through the fuel tank breather hose if
64
UF1W10E0.book Page 65 Monday, November 26, 2007 3:57 PM
Operation
the watercraft was capsized. Normally, the
water separator is empty.
the water is discharged from the electric bilge
pilot outlet at the stern.
1
2
1
1 Water separator
2 Drain screw
If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to install the drain screw after draining the water
separator.
EJU32450
Bilge
Check the bilge for moisture and fuel residue.
This watercraft is equipped with a conventional jet vacuum bilge draining system and an
electric bilge draining system. The electric
bilge draining system is operated when the
engine is running. When excess water reaches the water inlet of the electric bilge pump,
1 Electric bilge pilot outlet
A small quantity of water will remain in the
bilge and should be drained manually. To
drain any residual water, beach the watercraft
and perform the following procedure.
ECJ00350
CAUTION:
If starting the engine after the watercraft
has capsized, do not operate the engine at
full throttle when water is being discharged from the electric bilge pilot outlet
at the stern. Excessive water in the bilge
can splash into the engine, which can result in severe damage.
To drain water from the bilge:
(1) Remove the stern drain plugs.
(2) Raise the bow of the watercraft until the
water drains.
(3) After the water has drained, wipe the
bilge with dry rags to make sure that it is
thoroughly dry.
(4) Install the stern drain plugs.
ECJ00360
CAUTION:
●
65
Before installing the stern drain plugs,
clean the drain plug threads to remove
any foreign materials, such as dirt or
sand. Otherwise, the stern drain plugs
UF1W10E0.book Page 66 Monday, November 26, 2007 3:57 PM
Operation
●
could be damaged, allowing water to enter the engine compartment.
Make sure that the stern drain plugs are
tightened securely before launching the
watercraft. Otherwise, water may flood
the engine compartment and cause the
watercraft to submerge.
place it if it is not in good condition. (See page
99 for battery recharging procedures.)
Also, check that the battery leads are tightened securely and that there is no corrosion
on the battery terminals. Check that the
breather hose is securely connected to the
battery and that it is not pinched.
EJU32471
Stern drain plugs
Check the stern drain plugs for proper installation.
1
2
3
1 Positive (+) battery terminal: Red lead
2 Negative (–) battery terminal: Black lead
3 Breather hose
1
EWJ00450
WARNING
1 Stern drain plugs
ECJ00360
●
CAUTION:
●
●
Before installing the stern drain plugs,
clean the drain plug threads to remove
any foreign materials, such as dirt or
sand. Otherwise, the stern drain plugs
could be damaged, allowing water to enter the engine compartment.
Make sure that the stern drain plugs are
tightened securely before launching the
watercraft. Otherwise, water may flood
the engine compartment and cause the
watercraft to submerge.
●
The battery must always be fully
charged and in good condition. Loss of
battery power may leave you stranded.
Never operate the watercraft if the battery does not have sufficient power to
start the engine or if it shows any other
signs of decreased power.
Be sure to connect the breather hose to
the battery. Fire or explosion could result if the breather hose is damaged, obstructed, or not connected properly.
Make sure that the battery is securely held in
place.
EJU32481
Battery
Check the battery electrolyte level and check
that the battery has sufficient power to start
the engine easily. Recharge the battery or re-
66
UF1W10E0.book Page 67 Monday, November 26, 2007 3:57 PM
Operation
EJU32570
Fire extinguisher
Check that there is a full fire extinguisher on
board.
contact a Yamaha dealer or a fire extinguisher dealer to obtain one meeting the
proper specifications.
Fire extinguisher:
Classification:
B-1
Capacity:
2 lb or more
EJU32590
The fire extinguisher container is located in
the seat storage compartment.
To open the fire extinguisher container, turn
the cap counterclockwise.
Throttle lever
Check the throttle lever for proper operation.
Squeeze and release the throttle lever several
times to make sure that there is no hesitation
in its travel. It should be smooth over the complete range and spring back to the idle position when released.
EWJ00490
1 Fire extinguisher container
2 Fire extinguisher container cap
To close the fire extinguisher container, insert
the fire extinguisher into the container, and
then install the cap and tighten it securely.
NOTE:
●
●
To check the fire extinguisher, see the instructions supplied by the fire extinguisher
manufacturer. Always keep the fire extinguisher in the fire extinguisher container.
Always carry a fire extinguisher on board. A
fire extinguisher is not standard equipment
with this watercraft. If you do not have one,
67
WARNING
Before starting the engine, always check
the operation of the throttle lever.
EJU32610
Steering system
Check the handlebars for looseness.
Turn the handlebars as far as possible to the
right and left to make sure that operation is
smooth and unrestricted throughout the
whole range. Also, make sure that the jet
thrust nozzle moves as the handlebars are
UF1W10E0.book Page 68 Monday, November 26, 2007 3:57 PM
Operation
turned, and that there is no free play between
the handlebars and the jet thrust nozzle.
Also, make sure that the reverse gate goes up
completely when the shift lever is pushed
down.
Check that the handlebars are locked in
place. (See “Tilt lever” on page 36 for more information.)
EWJ00030
WARNING
EJU36580
Shift lever and reverse gate
Check the shift lever and reverse gate for
proper operation.
Make sure that the reverse gate goes down
completely when the shift lever is pulled up.
●
●
●
●
●
Make sure that the throttle lever is completely released and that the engine is at
idle before shifting into reverse.
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.
Use reverse for slow-speed maneuvering only.
Make sure that there are no obstacles or
people behind you before shifting into
reverse.
Do not touch the reverse gate while the
shift lever is being operated, otherwise
you could be pinched.
68
UF1W10E0.book Page 69 Monday, November 26, 2007 3:57 PM
Operation
shifted from neutral to bow up or bow
down.
EJU32641
Quick Shift Trim System (QSTS)
Operate the QSTS selector lock lever and the
QSTS selector several times to check that
they operate properly.
(1) Squeeze the QSTS selector lock lever
and check that it returns smoothly to its
original position when released.
(2) Check that the QSTS selector turns
smoothly when the lever is squeezed and
check that the selector locks in place at
each position when the lever is released.
If the mechanism does not work properly,
have a Yamaha dealer service it.
EJU32650
(3) Check that the angle of the jet thrust nozzle changes when the QSTS selector is
Jet intake
Carefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the jet intake is clogged,
cavitation could occur, reducing jet thrust, and
possibly damaging the jet pump.
In some cases, the engine may overheat because of lack of cooling water, and damage to
the engine could result. Cooling water is fed to
the engine by the jet pump. (See page 106 for
jet intake cleaning procedures.)
EWJ00470
WARNING
●
69
Keep away from the intake grate while
the engine is on. Items such as long hair,
loose clothing, or PFD straps can be-
UF1W10E0.book Page 70 Monday, November 26, 2007 3:57 PM
Operation
●
come entangled in moving parts, resulting in severe injury or drowning.
Stop the engine and remove the clip
from the engine shut-off switch before
removing any debris or weeds, which
may have collected around the jet intake.
EJU32670
Switches
ECJ00410
CAUTION:
Do not run the engine for more than 15
seconds when checking the switches on
land without supplying water, otherwise
the engine could overheat.
Check the start switch, the engine stop
switch, and the engine shut-off switch for
proper operation.
Push the start switch to start the engine. As
soon as the engine starts running, push the
engine stop switch to verify that the engine
stops immediately. Restart the engine, and
then pull the engine shut-off cord to remove
the clip from the engine shut-off switch to verify that the engine stops immediately. (See
pages 33 to 34 for information on proper operation of the start switch, the engine stop
switch, and the engine shut-off switch.)
3
1
5
EJU32660
Engine shut-off cord
Check that the engine shut-off cord is not
frayed or broken. If the cord is damaged, replace it; never try to repair it or tie it together.
4
2
1
2
3
4
5
Start switch
Engine stop switch
Engine shut-off switch
Clip
Engine shut-off cord
EJU36890
Cooling water pilot outlets
Check that water comes out from the port
(left) cooling water pilot outlets while the en-
70
UF1W10E0.book Page 71 Monday, November 26, 2007 3:57 PM
Operation
gine is running and the watercraft is in the water. (See page 34 for more information.)
EJU32740
Operation
EWJ00510
WARNING
Before operating your watercraft, become
familiar with all of the controls. Consult a
Yamaha dealer about any control or function that you do not fully understand. Failure to understand how the controls work
could cause an accident or prevent you
from avoiding an accident.
ECJ00460
EJU32710
Multifunction information center
Check the multifunction information center for
proper operation. (See page 45 for information on proper operation of the multifunction
information center.)
CAUTION:
Make sure that the stern drain plugs are
tightened securely before launching the
watercraft.
EJU36660
Engine break-in
The engine break-in period is essential to allow the various components of the engine to
wear and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer component
life.
ECJ00440
CAUTION:
Be sure to check the engine oil level before operating the watercraft for the first
time. (See page 63 for engine oil checking
procedures.)
71
UF1W10E0.book Page 72 Monday, November 26, 2007 3:57 PM
Operation
(1) Launch the watercraft and start the engine. (See page 72 for engine starting
procedures.)
(2) For the first 5 minutes, run the engine at
trolling speed only. For the 30 minutes of
operation after that, keep the engine
speed below 5000 r/min. For the 1 hour of
operation after that, keep the engine
speed below 6000 r/min.
(3) Proceed with normal operation.
(1) If the lock mode of the Yamaha Security
System is selected, use the remote control transmitter to select the unlock mode.
(See page 41 for Yamaha Security System lock and unlock mode selection procedures.)
(2) Launch the watercraft in water free from
weeds and debris and at least 60 cm (2 ft)
deep.
ECJ00430
CAUTION:
Failure to follow the engine break-in procedure could result in reduced engine life
or even severe engine damage.
EJU32801
Launching the watercraft
When launching the watercraft, make sure
that there are no obstacles behind you.
Use the remote control transmitter to select
the unlock mode. (See page 41 for Yamaha
Security System lock and unlock mode selection procedures.)
After the watercraft is in the water, start the
engine. Shift into reverse and move the watercraft back slowly. If there are waves, someone should make sure that the watercraft is
not pushed into the trailer before backing
away.
EJU36340
Starting the engine
EWJ00560
WARNING
EWJ00570
WARNING
Never operate in water that is less than 60
cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged object, which could result in injury.
ECJ00470
CAUTION:
Never operate in water that is less than 60
cm (2 ft) deep, otherwise pebbles or sand
could be sucked into the jet intake, causing impeller damage and engine overheating.
Never start the engine or let it run for any
length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a
colorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.
72
UF1W10E0.book Page 73 Monday, November 26, 2007 3:57 PM
Operation
(3) Attach the engine shut-off cord to your left
wrist, and then attach the clip to the engine shut-off switch.
1
(4) Push the start switch (green button), and
then release it as soon as the engine
starts to run.
2
3
1 Clip
2 Engine shut-off switch
3 Engine shut-off cord
NOTE:
The engine will not start if the throttle lever is
squeezed.
EWJ00580
WARNING
Check that the engine shut-off cord is not
frayed or broken, and keep it free from the
handlebars so that the engine stops if the
operator falls off. The engine shut-off cord
may not pull free if wrapped around the
handlebars when the operator falls off, allowing the watercraft to continue to run
and cause an accident.
NOTE:
It is not possible to start the engine with the
clip removed from the engine shut-off switch.
73
ECJ00480
CAUTION:
●
●
Never push the start switch while the engine is running.
Do not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not start
in 5 seconds, release the start switch,
wait 15 seconds, and then try again.
UF1W10E0.book Page 74 Monday, November 26, 2007 3:57 PM
Operation
EJU32860
Stopping the engine
To stop the engine, release the throttle lever,
and then push the engine stop switch (red
button).
EWJ00600
WARNING
You need throttle to steer. Shutting the engine off can cause you to hit an obstacle
you are attempting to avoid. A collision
could result in severe injury or death.
EJU32881
Leaving the watercraft
If leaving the watercraft, select the lock mode
of the Yamaha Security System and remove
the engine shut-off cord to reduce the chance
of accidental starting or unauthorized use by
children or others. (See page 41 for Yamaha
Security System lock and unlock mode selection procedures.)
EJU32900
Operating your watercraft
EJU32951
Getting to know your watercraft
Operating your watercraft requires skills acquired through practice over a period of time.
Take the time to learn the basic techniques
well before attempting more difficult maneuvers.
Operating your new watercraft can be a very
enjoyable activity, providing you with hours of
pleasure. However, it is essential to familiarize yourself with the operation of the watercraft to achieve the skill level necessary to
enjoy riding safely.
Before operating this watercraft, read this
owner’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all
warning and caution labels on the watercraft.
Pay particular attention to the safety information on page 10. Also, watch the Basic Orientation Video provided with your watercraft.
These materials should give you an understanding of the watercraft and its operation.
Remember: This watercraft is designed to
carry the operator and up to 2 passengers.
Never exceed the maximum load limit or allow
more than 3 persons (or 2 persons if a waterskier is being pulled) to ride the watercraft at
any time.
Maximum load:
240 kg (530 lb)
Load is the total weight of cargo, operator, and passengers.
EJU32990
Learning to operate your watercraft
Before operating the watercraft, always perform the pre-operation checks listed on page
61. The short time spent checking the watercraft will reward you with added safety and reliability.
74
UF1W10E0.book Page 75 Monday, November 26, 2007 3:57 PM
Operation
Check state and local laws before operating
your watercraft.
Operate defensively at safe speeds and keep
a safe distance away from people, objects,
and other watercraft. Select a wide area to
learn in, where there is good visibility and light
boat traffic.
fabrics, like those used in bicycle shorts. A full
wetsuit can also protect against hypothermia
(subnormal body temperature) and abrasions.
Footwear and gloves are recommended.
Eye protection is recommended to keep wind,
water, and glare from the sun out of your eyes
while you operate your watercraft. Restraining
straps for eyewear are made which are designed to float should your eyewear fall in the
water.
You should grip the handlebars firmly and
keep both feet on the floor of the footwell. Do
not attempt to ride with passengers until your
operating skills are fully developed.
EJU33050
Riding with passengers
Use the buddy system—operate with someone nearby. Scan constantly for people, objects, and other watercraft. Be alert for
conditions that limit your visibility or block your
vision of others.
Attach the engine shut-off cord to your left
wrist and keep it free from the handlebars so
that the engine stops if you, the operator, fall
off.
Wear a personal flotation device (PFD). All
riders must wear a U.S. Coast Guard approved PFD that is suitable for personal watercraft use.
Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into the water or
being near the jet thrust nozzle. Normal swimwear does not adequately protect against
forceful water entry into the rectum and vagina. All riders must wear a wetsuit bottom or
clothing that provides equivalent protection.
Such clothing includes thick, tightly woven,
sturdy and snug-fitting apparel such as denim, but does not include spandex or similar
75
When 2 or 3 persons (including the operator)
are on board, the watercraft handles differently, and is not as easy to maneuver, so operating it requires a higher degree of skill. Before
attempting to operate the watercraft with passengers on board, the operator must practice
operating the watercraft alone enough to be
able to acquire the necessary skills.
The passengers must always wear a U.S.
Coast Guard approved PFD and a wetsuit
bottom or equivalent.
EWJ00540
WARNING
Do not apply throttle when anyone is at the
rear of the watercraft. Turn the engine off
or keep it at idle. Water and/or debris exiting the jet thrust nozzle can cause severe
injury. Passengers should not attempt to
board the watercraft if the operator is applying throttle.
Do not give a ride to children whose feet cannot reach the floor of the footwell. The passengers should hold on firmly, either to the
person in front of them or to the handgrip pro-
UF1W10E0.book Page 76 Monday, November 26, 2007 3:57 PM
Operation
vided, and keep their feet on the floor of the
footwell. Never allow a passenger to ride in
front of the operator.
●
Practice reboarding in shallow water before riding in deep water.
EWJ00550
WARNING
When passengers are on board, make
sure that they are holding on firmly and
have their feet on the floor of the footwell
before you start to accelerate.
When pulling a water-skier, the spotter should
face to the rear while holding the handgrip
with both hands. The spotter should always sit
astride the seat with both feet placed firmly on
the floor of the footwell for proper balance.
Follow state laws regarding water-skiing,
such as those for skier-down flags, rearwardfacing spotter, and other requirements.
EJU33091
Boarding and starting in shallow water
(1) Launch the watercraft in water free from
weeds and debris and at least 60 cm (2 ft)
deep.
EJU33080
Starting the watercraft
EWJ00710
WARNING
●
●
●
●
Scan constantly for people, objects, and
other watercraft. Be alert for conditions
that limit your visibility or block your vision of others.
Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft.
Do not follow directly behind watercraft
or other boats. Do not go near others to
spray or splash them with water. Avoid
sharp turns or other maneuvers that
make it hard for others to avoid you or
understand where you are going. Avoid
areas with submerged objects or shallow water.
Take early action to avoid collisions. Remember, watercraft and other boats do
not have brakes. Do not release the
throttle lever when trying to steer away
from objects—you need throttle to steer.
EWJ00570
WARNING
Never operate in water that is less than 60
cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged object, which could result in injury.
ECJ00470
CAUTION:
Never operate in water that is less than 60
cm (2 ft) deep, otherwise pebbles or sand
could be sucked into the jet intake, causing impeller damage and engine overheating.
76
UF1W10E0.book Page 77 Monday, November 26, 2007 3:57 PM
Operation
(2) Board the watercraft from the side or the
rear.
(3) Attach the engine shut-off cord to your left
wrist, and then attach the clip to the engine shut-off switch.
(4) Grip the handlebars with both hands,
place both feet on the floor of the footwell,
start the engine, and then look in all directions before starting off.
EJU36350
Boarding alone
(1) Swim to the rear of the watercraft and
place both hands on the boarding platform, pull yourself up, and then grasp the
handgrip with one hand.
EJU33110
Boarding and starting from a dock
(1) Board the watercraft from the side.
(2) Attach the engine shut-off cord to your left
wrist, and then attach the clip to the engine shut-off switch.
(3) Push the watercraft away from the dock,
grip the handlebars with both hands,
place both feet on the floor of the footwell,
start the engine, and then look in all directions before starting off.
EJU36080
Boarding and starting in deep water
EWJ01110
WARNING
●
●
The operator and passengers should
practice boarding in shallow water before riding in deep water. Boarding in
deep water requires more skill.
The fatigue and exposure that could result after unsuccessful attempts to get
back on the watercraft may increase the
risk of injuries and drowning.
77
(2) Pull yourself up to a kneeling position on
the platform, and then move to the seat
and sit astride.
(3) Attach the engine shut-off cord to your left
wrist, and then attach the clip to the engine shut-off switch.
(4) Grip the handlebars with both hands,
place both feet on the floor of the footwell,
UF1W10E0.book Page 78 Monday, November 26, 2007 3:57 PM
Operation
start the engine, and then look in all directions before starting off.
NOTE:
This watercraft is equipped with a reboarding
step, which you can lower to make reboarding
easier. The step returns automatically to the
up position after you have boarded.
(1) Climb on board as noted in the previous
section, and sit astride the seat.
(2) Attach the engine shut-off cord to your left
wrist, and then attach the clip to the engine shut-off switch.
(3) Have the passengers move to the rear of
the watercraft.
EWJ00610
WARNING
Before starting off, make sure that there
are no boats, swimmers, or obstacles
around you.
EJU33162
Boarding with passengers
EWJ00660
WARNING
Severe internal injuries can occur if water
is forced into body cavities as a result of
being near the jet thrust nozzle. Do not apply throttle until the passengers are seated
with their feet on the floor of the footwell
and are securely holding on to the person
in front of them or to the handgrip provided.
(4) Have a passenger board and sit astride
the seat. If a second passenger is boarding, have him or her follow the same procedure.
78
UF1W10E0.book Page 79 Monday, November 26, 2007 3:57 PM
Operation
NOTE:
When a passenger is boarding, both the passengers and the operator should try to balance the watercraft.
tion, and then move to the seat and sit
astride to balance the watercraft.
(5) Check that the passengers have their
feet on the floor of the footwell and are
securely holding on to the person in front
of them or to the handgrip provided. Never allow a passenger to ride in front of the
operator.
(6) Start the engine, look in all directions, and
then accelerate to planing speed.
EWJ00610
WARNING
Before starting off, make sure that there
are no boats, swimmers, or obstacles
around you.
NOTE:
The heavier the total weight of the operator
and passengers, the more difficult it will be to
balance the watercraft. Do not operate the
watercraft when the total weight exceeds 240
kg (530 lb) including any cargo. If it is difficult
to balance the watercraft at a standstill, proceed as follows:
(1) While the passengers are steadying the
watercraft, pull yourself up onto the
boarding platform into a kneeling posi-
79
(2) Have a passenger pull him or herself up
onto the boarding platform into a kneeling
position, then move to the seat and sit
astride to balance the watercraft.
(3) Attach the engine shut-off cord to your left
wrist, and then attach the clip to the engine shut-off switch.
(4) Start the engine and keep it at idle.
(5) Have the second passenger pull him or
herself up onto the boarding platform into
a kneeling position, then crawl onto the
seat as the watercraft accelerates.
UF1W10E0.book Page 80 Monday, November 26, 2007 3:57 PM
Operation
(6) Gradually increase the speed to balance
the watercraft.
ride plate while pushing down on the gunwale with your right hand or foot.
EJU33230
Capsized watercraft
If the watercraft capsizes, turn it over immediately.
Be sure to carefully follow the procedures below to prevent injury, or damage to the watercraft.
EWJ00670
WARNING
IMPROPER UPRIGHTING CAN CAUSE INJURY:
● Be sure to shut the engine off by pulling
on the engine shut-off cord to remove
the clip from the engine shut-off switch.
● Do not put your hands in the intake
grate.
NOTE:
If the port (left) side of the capsized watercraft
is tilting up, push down on the gunwale so that
the port (left) side is down before turning the
watercraft clockwise.
ECJ00540
ECJ00530
CAUTION:
If the watercraft capsizes, release the
throttle lever immediately. Oil could flow
into the air filter case and the engine could
be damaged.
(1) Remove the clip from the engine shut-off
switch.
(2) Swim to the rear of the watercraft. Pull the
watercraft over with your left hand on the
CAUTION:
Do not turn the watercraft over counterclockwise, otherwise water can enter the
engine, which can result in severe damage.
(3) Start the engine and operate the watercraft to discharge any water remaining in
the engine compartment. (If the engine
does not start, see “Towing the watercraft” on page 109 or “Submerged watercraft” on page 109.)
80
UF1W10E0.book Page 81 Monday, November 26, 2007 3:57 PM
Operation
ECJ00550
CAUTION:
B. Less throttle produces lower thrust, so
the watercraft will turn more gradually.
Do not operate the engine at full throttle
for at least 1 minute after the engine has
been restarted. Excessive water in the
bilge can splash into the engine, which
can result in severe damage.
NOTE:
To efficiently discharge water from the engine
compartment, operate the watercraft as
straight as possible and above planing speed
for at least 2 minutes.
EJU33250
Turning the watercraft
Steering control depends on the combination
of handlebar position and the amount of throttle.
Water sucked in through the intake grate is
pressurized by the impeller in the jet pump. As
the pressurized water is expelled from the
pump through the jet thrust nozzle, it creates
thrust to move and steer the watercraft. The
higher the engine speed, the more thrust produced.
The amount of jet thrust, in addition to the position of the handlebars, determines how
sharply you turn.
A. More throttle produces higher thrust, so
the watercraft will turn more sharply.
81
C. Releasing the throttle lever completely
produces only minimum thrust. If you are
traveling at speeds above trolling, you will
have rapidly decreasing ability to steer
without throttle. You may still have some
turning ability immediately after releasing
the throttle lever, but once the engine
slows down, the watercraft will no longer
respond to handlebar input until you apply throttle again or you reach trolling
speed.
At trolling speed, the watercraft can be
turned gradually by handlebar position
alone using just the amount of thrust
available at idle.
UF1W10E0.book Page 82 Monday, November 26, 2007 3:57 PM
Operation
D. If the engine is stopped while riding, there
is no thrust. The watercraft will go straight
even though the handlebars are turned.
You need throttle to steer.
EWJ00770
WARNING
●
●
Do not release the throttle lever when
trying to steer away from objects—you
need throttle to steer. A collision could
result in severe injury or death.
When operating at higher speeds, make
gradual turns or slow down before turning. Sharp high-speed turns may cause
the watercraft to slide sideways or spin,
throwing the operator and passengers
overboard, which could cause an injury.
This model is equipped with the Yamaha Engine Management System (YEMS) that includes an off-throttle steering (OTS) system.
It will activate at planing speeds should you
attempt to steer the watercraft after releasing
the throttle lever (see condition C above).
The OTS system assists in turning by continuing to supply some thrust while the watercraft
is decelerating, but you can turn more sharply
if you apply throttle while turning the handlebars. The OTS system does not function below planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar in-
put until you apply throttle again or you reach
trolling speed.
EJU33290
Stopping the watercraft
The watercraft is not equipped with a separate braking system. It is stopped by water resistance when the throttle lever is released.
From full speed, the watercraft comes to a
complete stop in approximately 100 m (330 ft)
after the throttle lever is released or the engine is stopped, although this distance will
vary depending on many factors, including
gross weight, water surface conditions, and
wind direction. The watercraft slows down as
soon as the throttle lever is released, but will
coast for a distance before fully stopping. If
you are not sure you can stop in time before
hitting an obstacle, apply throttle and turn in
another direction.
EWJ00740
WARNING
●
●
●
●
Allow adequate stopping distance.
Take early action to avoid collisions. Remember, watercraft and other boats do
not have brakes.
Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft to give you
time to stop.
Do not shut the engine off when slowing
down in case you need engine power to
82
UF1W10E0.book Page 83 Monday, November 26, 2007 3:57 PM
Operation
●
steer away from a boat or other obstacle
that comes into your path.
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.
Once the engine is idling, shift into reverse
and gradually increase engine speed. Make
sure that there are no obstacles or people behind you before shifting into reverse.
EJU35960
Beaching the watercraft
(1) Make sure that there are no boats, swimmers, or obstacles near the beach. Release the throttle lever about 100 m (330
ft) before you reach the intended beaching area.
(2) Approach the beach slowly and stop the
engine before reaching land.
Remember, you need throttle to steer.
(3) Get off the watercraft and pull it up on the
beach.
ECJ00490
CAUTION:
Small pebbles, sand, seaweed, and other
debris can be sucked into the jet intake
and impair or damage the impeller. Always
stop the engine and get off the watercraft
before beaching it.
EJU36060
Docking the watercraft
(1) Make sure that there are no boats, swimmers, or obstacles near the watercraft.
Reduce speed about 100 m (330 ft) away
from the dock.
(2) Slowly approach the dock and stop the
engine just before coming alongside it.
EJU36670
Reverse on waterways
Reverse can be used for slow-speed maneuvering when it is necessary to back up out of
tight spots where you cannot turn around. Reverse can be used to slow down or stop only
during slow-speed maneuvering, such as
when docking.
83
NOTE:
This model is equipped with a function which
limits the engine speed in reverse.
EJU33350
Rough water operation
The force of landing after jumping can cause
a strong impact on both the watercraft and the
operator and passengers. It is possible for the
operator to hit his or her chest or jaw on the
watercraft or handlebars and be injured. The
passengers could also impact the watercraft
and be injured.
Do not operate the watercraft with your chin
right above the handlebars. In addition, the
operator and passengers should keep their
feet on the floor of the footwell.
Operating in rough water or jumping waves
can also crack the watercraft hull and deck,
and damage internal parts. Avoid operating in
rough water or bad weather conditions.
UF1W10E0.book Page 84 Monday, November 26, 2007 3:57 PM
Operation
EJU37140
Post-operation care
To keep your watercraft in top shape, always
take it out of the water after using it and perform the following procedures. Leaving the
watercraft in the water for extended periods
will accelerate the rate of normal deterioration
of the jet unit components and hull finish. Marine organisms and corrosion are some of the
conditions that can adversely affect the life of
many watercraft components.
(1) Remove the watercraft from the water.
(2) Wash down the hull, handlebars, and jet
unit with fresh water.
(3) Remove the seat and check the engine
compartment for water. To drain excess
water, remove the stern drain plugs, and
then raise the bow of the watercraft
enough to allow the water in the bilge to
drain out.
(5) Flush the cooling system to prevent it
from clogging with salt, sand, or dirt. (See
page 86 for flushing procedures.)
(6) Drain residual water from the exhaust
system by alternately squeezing and releasing the throttle lever for 10 to 15 seconds while the engine is running.
ECJ00561
CAUTION:
Do not run the engine for more than 15
seconds without supplying water, otherwise the engine could overheat.
(7) Rinse the engine and engine compartment with a small amount of water.
ECJ00570
CAUTION:
Do not use high-pressure water when rinsing the engine or engine compartment as
severe engine damage could result.
(8) Wipe the engine and engine compartment dry with a clean cloth (repeat step 3,
if necessary).
(9) Wipe the hull, handlebars, and jet unit dry
with a clean cloth.
(10) Spray a rust inhibitor, such as Yamaha
Silicone Protectant and Lubricant, on metallic parts to minimize corrosion.
(11) Allow the engine compartment to air dry
completely before installing the seat.
NOTE:
This watercraft is equipped with a jet vacuum
bilge draining system and an electric bilge
draining system that remove water from the
engine compartment while you are underway.
However, some residual water will remain.
(See page 65 for bilge draining procedures.)
(4) Place the watercraft in a horizontal position.
84
UF1W10E0.book Page 85 Monday, November 26, 2007 3:57 PM
Operation
EJU33461
Transporting
When transporting the watercraft on a trailer,
secure the tie downs to the trailer through the
bow eye and stern eyes.
ECJ00641
CAUTION:
●
●
●
Do not attach ropes or tie downs to any
part of the watercraft other than the bow
eye and stern eyes to secure the watercraft to the trailer. Otherwise, the watercraft may be damaged.
Do not route ropes or tie downs over the
seat, as they may leave permanent
marks on the seat’s surface. Also, wrap
the ropes or tie downs with towels or
rags where they touch the body of the
watercraft to avoid scratches or damage.
Before putting the watercraft on the trailer or transporting it, be sure to put the
shift lever in the forward position, otherwise the reverse gate may hit an obstacle, which may cause damage.
85
UF1W10E0.book Page 86 Monday, November 26, 2007 3:57 PM
Maintenance and care
EJU33490
Storage
EWJ00330
adapter into the flushing hose connector
and turn it until it is securely connected.
WARNING
Always place the watercraft upright in a
horizontal position when storing it, otherwise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
Storage for long periods of time, such as winter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
2
3
1
1 Flushing hose connector cap
2 Garden hose adapter
3 Flushing hose connector
Flushing the cooling system
(4) Connect the garden hose adapter to a
water tap using a garden hose.
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
NOTE:
EJU33532
ECJ00121
CAUTION:
●
●
Do not supply water to the cooling water
passages when the engine is not running. The water could flow back through
the muffler into the crankcase, causing
severe engine damage.
Do not run the engine for more than 15
seconds without supplying water or
over 4000 r/min on land, otherwise the
engine could overheat.
(1) Place the watercraft in a horizontal position.
(2) Remove the rear seat and seat storage
compartment. (See page 30 for seat removal and installation procedures.)
(3) Remove the flushing hose connector
cap, and then insert the garden hose
A garden hose is not included and must be
purchased separately.
(5) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the jet thrust nozzle.
(6) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps.
(7) Turn the water supply off, and then force
the remaining water out of the cooling
86
UF1W10E0.book Page 87 Monday, November 26, 2007 3:57 PM
Maintenance and care
water passages by alternately squeezing
and releasing the throttle lever for 10 to
15 seconds.
(8) Stop the engine.
(9) Remove the garden hose adapter and install the flushing hose connector cap.
●
EJU36901
Lubrication
EWJ00260
WARNING
Do not spray flammable rust inhibitor
products on engine surfaces while the engine is hot. The sprayed substance or propellants could catch fire.
(1) Lubricate all cables such as the throttle
and steering cables.
●
●
NOTE:
Use a Yamaha Power Cable Luber and
Yamaha Lube-Zall to pressure-lubricate the
cables and purge out any moisture between
the inner and outer cables.
(2) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
98.
EJU33661
Fuel system
EWJ00281
WARNING
GASOLINE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE!
● Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.
● Stop the engine before refueling.
● Refuel in a well-ventilated area with the
watercraft in a horizontal position.
● Do not stand or sit on the watercraft
while refueling.
● Take care not to spill gasoline. If gasoline spills, wipe it up immediately with
87
●
dry rags. Always properly dispose of
gasoline-soaked rags.
Avoid overfilling the fuel tank. Stop filling when the fuel level reaches approximately 50 mm (2 in) from the top of the
fuel tank. Fuel expands as it warms up
and could overflow if the fuel tank has
been overfilled. If temporarily leaving
the watercraft with a full fuel tank, do not
leave it in direct sunlight. Leave it in a
well-ventilated area with the watercraft
in a horizontal position.
Tighten the fuel tank filler cap securely
after refueling.
If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical
attention.
If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
Top off the fuel tank with fresh gasoline and
add one ounce of Yamaha Fuel Stabilizer and
Conditioner per each gallon of fuel.
EJU33680
Battery
If the watercraft will not be used for more than
a month, remove the battery from the watercraft and store it in a cool, dry place.
(1) Disconnect the negative (–) battery lead
first, then the positive (+) battery lead and
breather hose, and then remove the battery from the watercraft.
(2) Clean the battery casing using fresh water.
(3) If the battery terminals are dirty or corroded, clean them with a wire brush.
(4) Fully charge the battery.
(5) Apply Yamaha Marine Grease or
Yamaha Grease A to the battery termi-
UF1W10E0.book Page 88 Monday, November 26, 2007 3:57 PM
Maintenance and care
nals, and then store the battery in a cool,
dry place.
(6) Check the battery at least once every 2
months and fully charge it if necessary.
ECJ00100
CAUTION:
(4) Wax the hull with a non-abrasive wax
such as Yamaha Silicone Wax.
(5) Wipe all vinyl and rubber components,
such as the seat and engine compartment seals, with a vinyl protectant such
as Yamaha Protectant.
Always keep the battery charged. Storing
a discharged battery can cause permanent
battery damage.
To check the condition of the battery, check
the specific gravity of the electrolyte or measure the voltage at both battery terminals.
Charge the battery if the voltage is less than
12 volts.
Specific gravity (for reference):
1.28 at 20 °C (68 °F)
It is recommended to have a Yamaha dealer
check the specific gravity and charge the battery. If you maintain the battery yourself, be
sure to read and follow the instructions provided with the battery tester and charger you
use.
EJU33740
Cleaning the watercraft
Clean the watercraft before storing it for a long
period.
(1) Wash down the hull, handlebars, and jet
unit with fresh water.
(2) Rinse the engine and bilge area with
fresh water. Drain all of the water and
wipe up any remaining moisture with
clean, dry rags.
ECJ00110
CAUTION:
Do not use high-pressure water when rinsing the engine and bilge area as severe engine damage could result.
(3) Spray the engine’s exterior with a rust inhibitor and lubricant such as Yamaha Silicone Protectant and Lubricant.
88
UF1W10E0.book Page 89 Monday, November 26, 2007 3:57 PM
Maintenance and care
EJU33751
Maintenance and adjustments
Periodic inspection, adjustment, and lubrication will keep your watercraft in the safest and
most efficient condition possible. Safety is an
obligation of the watercraft owner. Proper
maintenance must be carried out to keep the
exhaust emission and sound levels within the
regulated limits. The most important points of
watercraft inspection, adjustment, and lubrication are explained on the following pages.
See a Yamaha dealer for genuine Yamaha replacement parts and optional accessories designed for your watercraft.
Remember, failures that are the result of the
installation of parts or accessories which are
not qualitatively equivalent to genuine
Yamaha parts are not covered by the limited
warranty.
Maintenance, replacement, or repair of the
emission control devices and system may
be performed by any marine SI engine repair establishment or individual. Warranty
repair, however, must be performed at an
authorized Yamaha marine dealership.
use. Consult a Yamaha dealer before attempting any modifications.
NOTE:
A service manual is available for purchase
through a Yamaha dealer for owners who
have the mechanical skills, tools, and other
equipment necessary to perform maintenance not covered by this owner’s/operator’s
manual.
EJU33800
Owner’s/operator’s manual and tool
kit
It is advisable to always carry the owner’s/operator’s manual and tool kit with you whenever you use the watercraft. For your
convenience, a storage compartment is provided on the watercraft for the manual and
tool kit.
EWJ00310
WARNING
●
●
Be sure to shut the engine off when you
perform maintenance unless otherwise
specified, otherwise an accident or injury could result from unexpected operation, moving parts, or electric shock. If
the owner is not familiar with watercraft
servicing, this work should be done by a
Yamaha dealer. Improperly serviced
components could fail or stop operating
correctly, which could result in an accident.
Modifications to this watercraft not approved by Yamaha may cause loss of
performance or excessive noise and exhaust emissions, or render it unsafe for
89
1 Storage compartment
NOTE:
To protect these materials from water damage, it would be a good idea to put them in a
waterproof bag. If your owner’s/operator’s
manual is damaged, order a replacement
from a Yamaha dealer.
The service information included in this manual is intended to provide you, the owner, with
the necessary information for completing your
own preventive maintenance and minor re-
UF1W10E0.book Page 90 Monday, November 26, 2007 3:57 PM
Maintenance and care
pairs. The tools provided in the tool kit are sufficient for this purpose, except that a torque
wrench may also be necessary to tighten nuts
and bolts.
1
2
3
4
5
6
7
Tool bag
Screwdriver
16 mm box wrench
10/12 mm box wrench
Pliers
Open-end wrench
Garden hose adapter
90
UF1W10E0.book Page 91 Monday, November 26, 2007 3:57 PM
Maintenance and care
EJU37060
Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, maintenance
may need to be performed more frequently depending on your operating conditions.
This “ ” mark indicates maintenance that you may do yourself.
This “ ” mark indicates work to be done by a Yamaha dealer.
Initial
Item
Operation
10
hours
50
hours
Thereafter every
100
hours
100
hours
200
hours
Page
6
12
12
24
months months months months
Spark plugs
Check, clean, adjust
96
Lubrication points
Lubricate
98
Internal engine
components
Lubricate
QSTS cables
Lubricate
—
Intermediate housing
Lubricate
98
Fuel system
Check
93
Fuel tank
Check, clean
93
Trolling speed
Check, adjust
101
*2
50 hours or 12 months
—
Throttle shaft
Check
Cooling water passages
Flush
Water inlet strainer
Check, clean
—
Bilge strainer
Clean
—
Electric bilge
pump strainer
Check, clean
—
Impeller
Check
—
Jet thrust nozzle
angle
Check, adjust
94
Steering master
Check
—
QSTS mechanism
Check, adjust
—
Shift cable and reverse gate
Check, adjust
94
Throttle cable
Check, adjust
95
Stern drain plugs
Check, replace
66
91
—
*1
86
UF1W10E0.book Page 92 Monday, November 26, 2007 3:57 PM
Maintenance and care
Initial
Item
Operation
10
hours
50
hours
Thereafter every
100
hours
100
hours
200
hours
Page
6
12
12
24
months months months months
Battery
Check, charge
99
Rubber coupling
Check
—
Engine mount
Check
—
Nuts and bolts
Check
—
Air filter element
Check
94
Engine oil
Replace
Oil filter
Replace
93
Valve clearance
Check, adjust
—
50 hours or 12 months
93
*1 This operation should be performed after every use.
*2 This operation should be performed before long-term storage.
92
UF1W10E0.book Page 93 Monday, November 26, 2007 3:57 PM
Maintenance and care
EJU34210
EJU36940
Checking the fuel system
Engine oil and oil filter
EWJ00380
EWJ00340
WARNING
Gasoline is highly flammable and explosive. Failure to check for and repair any
fuel leakage could result in a fire or explosion. A fire or explosion can cause severe
injury or death. Shut the engine off. Do not
smoke. Avoid spilling gasoline.
Fuel in the fuel lines is pressurized.
Fuel can spray out and cause injury or a
fire hazard if a fuel line is disconnected.
Do not run the engine with a fuel line disconnected.
Check the fuel system for leaks, cracks, and
malfunctions. If any problem is found, consult
a Yamaha dealer.
Check:
● Fuel tank filler cap and seal for damage.
● Fuel in fuel tank for water and dirt.
● Fuel tank for damage, cracks, and leakage.
● Fuel hoses and joints for damage, cracks,
and leakage.
● Air bleeding passages for leakage.
EJU34230
Fuel tank
Check the fuel tank for leakage and for water
in the tank. If water is found in the fuel system,
or if the fuel tank needs to be cleaned, have a
Yamaha dealer service the watercraft.
1
1 Fuel tank
93
WARNING
Engine oil is extremely hot immediately after the engine is turned off. Coming in contact with or getting any engine oil on your
clothes could result in burns.
ECJ00990
CAUTION:
●
●
Do not run the engine with too much or
not enough oil in the oil tank. Oil could
spray out and the engine could be damaged.
Be sure to change the engine oil after
the first 10 hours of operation, and every
50 hours thereafter or at the start of a
new season, otherwise the engine will
wear quickly.
The oil filter should be replaced every
year or every 100 hours of operation.
Have a Yamaha dealer replace the oil filter if necessary.
It is recommended to have a Yamaha dealer
change the engine oil. However, if you choose
to change the oil on your own, refer to the service manual for this watercraft.
NOTE:
Dispose of used oil according to local regulations.
UF1W10E0.book Page 94 Monday, November 26, 2007 3:57 PM
Maintenance and care
Recommended engine oil:
SAE 10W-30, 10W-40, 20W-40, 20W50
Oil grade:
API SE,SF,SG,SH,SJ,SL
Oil quantity:
With oil filter replacement:
3.1 L (3.28 US qt) (2.73 Imp.qt)
Without oil filter replacement:
3.0 L (3.17 US qt) (2.64 Imp.qt)
Total amount:
4.3 L (4.55 US qt) (3.78 Imp.qt)
Difference of A and B:
Maximum 5 mm (0.20 in)
ECJ00190
CAUTION:
If oil is leaking or the oil pressure warning
indicator comes on when the engine is
running, immediately shut the engine off
and have a Yamaha dealer check the watercraft. Continuing to operate the engine
under such conditions could cause severe
engine damage.
EJU34310
Air filter element
Have a Yamaha dealer check and clean or replace the air filter element every 12 months or
every 100 hours of operation.
If the steering is stiff or misadjusted, have a
Yamaha dealer service it.
EJU34321
EJU36590
Checking the jet thrust nozzle angle
Check the handlebars and jet thrust nozzle for
smooth operation.
Turn the handlebars as far as possible to the
right and left and check that the difference of
distances A and B between the jet thrust nozzle and the nozzle is within specification.
Checking the shift cable
Place the shift lever in the reverse position.
Make sure that the reverse gate makes contact with the stopper.
1 Stopper
94
UF1W10E0.book Page 95 Monday, November 26, 2007 3:57 PM
Maintenance and care
If the reverse gate does not make contact with
the stopper, have a Yamaha dealer service it.
EJU37030
Checking and adjusting the throttle
cable
Face the handlebars straight ahead, and then
check that the throttle cable moves back to
the set position smoothly and that the throttle
lever free play is within specification.
Squeeze and release the throttle lever. If the
throttle lever does not return smoothly, have a
Yamaha dealer service it.
If the specified throttle lever free play cannot
be obtained as described below, have a
Yamaha dealer make the adjustment.
FX SHO
(1) Remove the eight screws, and then remove the front handlebar cover.
(3) Make sure that the handlebars are facing
straight ahead, and then adjust the free
play by turning the adjuster.
1
2
3
4
Rubber cover
Locknut
Adjuster
Throttle lever free play
Throttle lever free play:
2.0–5.0 mm (0.08–0.20 in)
1 Front handlebar cover
(2) Slide the rubber cover away from the adjuster, and then loosen the locknut.
(4) Hold the adjuster with one wrench while
tightening the locknut with another
wrench. Slide the rubber cover to its original position.
(5) Install the front handlebar cover, and then
install the eight screws.
FX Cruiser SHO
(1) Remove the ten screws, and then remove the front and rear handlebar covers.
1 Front handlebar cover
2 Rear handlebar cover
95
UF1W10E0.book Page 96 Monday, November 26, 2007 3:57 PM
Maintenance and care
(2) Slide the rubber cover away from the adjuster, and then loosen the locknut.
(3) Make sure that the handlebars are facing
straight ahead, and then adjust the free
play by turning the adjuster.
1
2
3
4
(5) Install the front and rear handlebar covers as shown in the illustration, and then
install the ten screws.
Rubber cover
Locknut
Adjuster
Throttle lever free play
Throttle lever free play:
2.0–5.0 mm (0.08–0.20 in)
(4) Hold the adjuster with one wrench while
tightening the locknut with another
wrench. Slide the rubber cover to its original position.
EJU37040
Cleaning and adjusting the spark
plugs
The spark plug is an important engine component and is easy to inspect. The condition of
the spark plug can indicate something about
the condition of the engine. For example, if
one spark plug has a distinctly different color,
the engine could require servicing. Do not attempt to diagnose any problems yourself.
Have a Yamaha dealer service the watercraft.
Remove and inspect the spark plugs periodically; heat and deposits will cause the spark
plugs to slowly break down and erode. If electrode erosion becomes excessive, or if carbon
and other deposits are excessive, replace the
spark plug with the specified plug.
Specified spark plug:
LFR6A
96
UF1W10E0.book Page 97 Monday, November 26, 2007 3:57 PM
Maintenance and care
To remove a spark plug:
(1) Remove the seats. (See page 30 for seat
removal and installation procedures.)
(2) Remove the engine cover screws, and
then remove the engine cover.
2
coil coupler could be damaged. The spark
plug cap may be difficult to remove because the rubber seal on the end of the
cap fits tightly. To remove the spark plug
cap, simply twist it back and forth while
pulling it up; to install it, twist it back and
forth while pushing it down.
(4) Remove the spark plug.
Measure the spark plug gap with a wire
thickness gauge. Replace the spark plug
or adjust the gap to specification if necessary.
1
1 Engine cover screw
2 Engine cover
(3) Remove the spark plug cap bolts, and
then remove the spark plug cap.
NOTE:
If removing the spark plug cap nearest the
stern, remove the plastic tie that is securing
the wiring harness before removing the cap.
1 Spark plug gap
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
1
To install a spark plug:
(1) Clean the gasket surface.
(2) Wipe any dirt from the threads of the
spark plug.
(3) Install the spark plug, and then tighten it
to the specified torque.
2
3
1 Spark plug cap bolt
2 Spark plug cap
3 Plastic tie
ECJ00210
CAUTION:
Do not use any tools to remove or install
the spark plug cap, otherwise the ignition
97
Spark plug tightening torque:
24.5 Nm (18.1 ft-lb) (2.50 kgf-m)
NOTE:
If a torque wrench is not available when you
are installing a spark plug, a good estimate of
the correct torque is 1/4 turn to 1/2 turn past
finger tight using the spark plug wrench in-
UF1W10E0.book Page 98 Monday, November 26, 2007 3:57 PM
Maintenance and care
ble free play. (See page 95 for adjustment
procedures.)
cluded in the tool kit. Have the spark plug adjusted to the correct torque with a torque
wrench as soon as possible.
(4) Install the spark plug cap, and then install
the spark plug cap bolts and tighten them
to the specified torque.
NOTE:
●
●
Wipe off any water on the spark plug or inside the spark plug cap before installing the
cap. Push the spark plug cap down until it is
securely installed.
If the spark plug cap nearest the stern was
removed, secure the wiring harness by installing the plastic tie after installing the cap.
1 Adjuster
●
Steering cable (handlebar end)
●
Steering cable (jet thrust nozzle end)
QSTS rod (jet thrust nozzle end)
Spark plug cap bolt tightening torque:
7.6 Nm (5.6 ft-lb) (0.77 kgf-m)
EWJ00350
WARNING
Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks to
escape, which could result in a fire or explosion.
●
(5) Install the engine cover and engine cover
screws, and then install the seats.
EJU36970
Lubrication points
To keep moving parts sliding or rotating
smoothly, coat them with water-resistant
grease.
Recommended water-resistant grease:
Yamaha Marine Grease/Yamaha
Grease A
●
Throttle cable (handlebar end)
Loosen the adjuster and disconnect the
outer cable from the bracket. Spray a rust
inhibitor into the outer cable. Connect the
outer cable, and then adjust the throttle ca-
98
UF1W10E0.book Page 99 Monday, November 26, 2007 3:57 PM
Maintenance and care
●
Shift cable (shift lever end)
●
Shift cable (reverse gate end)
Grease quantity:
Initial 10 hours or 1 month:
33.0–35.0 cm³ (1.12–1.18 US oz)
(1.16–1.23 Imp.oz)
Every 100 hours or 12 months:
6.0–8.0 cm³ (0.20–0.27 US oz)
(0.21–0.28 Imp.oz)
1
1 Grease nipple
EJU34451
Checking the battery
●
Intermediate housing
Fill the intermediate housing with water-resistant grease through the grease nipple
using a grease gun.
99
Check the level of the battery electrolyte and
make sure that the negative (–) and positive
(+) battery leads are tightened securely.
EWJ00790
WARNING
Battery electrolyte is poisonous and dangerous, causing severe burns, etc. Electrolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
egg, or vegetable oil. Call a physician immediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an enclosed space, make sure that it is well ven-
UF1W10E0.book Page 100 Monday, November 26, 2007 3:57 PM
Maintenance and care
tilated. Always shield your eyes when
working near batteries.
KEEP OUT OF THE REACH OF CHILDREN.
ECJ00230
CAUTION:
●
●
Be careful not to place the battery on its
side.
Be sure to remove the battery from the
battery compartment when adding electrolyte or charging the battery.
To remove the battery:
Disconnect the negative (–) battery lead first,
then the positive (+) battery lead and breather
hose, and then remove the battery from the
watercraft.
To replenish the battery:
(1) Make sure that the electrolyte level is between the maximum and minimum level
marks.
To recharge the battery:
ECJ00250
CAUTION:
Do not attempt to charge a battery hastily.
Battery life could be shortened.
It is recommended to have a Yamaha dealer
charge the battery. If you charge the battery
yourself, be sure to read and follow the instructions provided with the battery tester and
charger you use.
To install the battery:
(1) Place the battery in the battery compartment and connect the battery leads to the
battery terminals.
(2) Connect the breather hose to the battery.
(3) Secure the battery in place.
1
2
3
1 Positive (+) battery terminal: Red lead
2 Negative (–) battery terminal: Black lead
3 Breather hose
EWJ00400
1 Maximum level mark
2 Minimum level mark
(2) If the electrolyte level is low, add distilled
water to raise it to the specified level.
ECJ00240
CAUTION:
Normal tap water contains minerals that
are harmful to a battery. Use only distilled
water for replenishing the battery.
WARNING
Be sure to connect the breather hose to
the battery. Fire or explosion could result
if the breather hose is damaged, obstructed, or not connected properly.
ECJ00260
CAUTION:
After installation, make sure that the battery leads are properly connected to the
battery terminals.
100
UF1W10E0.book Page 101 Monday, November 26, 2007 3:57 PM
Maintenance and care
EJU34490
Fuel injection system
The fuel injection system was set at the
Yamaha factory. If the fuel injection system
needs to be adjusted, have a Yamaha dealer
service the watercraft.
ECJ00220
CAUTION:
Do not attempt to adjust the fuel injection
system. If the settings are disturbed by
someone who does not have the necessary technical knowledge, poor engine
performance and damage may result.
EJU34500
Checking the trolling speed
(1) Place the watercraft in the water.
(2) Start the engine and warm it up. Use the
tachometer in the multifunction information center to check the trolling speed.
Trolling speed:
1250 ±100 r/min
If the trolling speed is out of specification,
have a Yamaha dealer service the watercraft.
101
UF1W10E0.book Page 102 Monday, November 26, 2007 3:57 PM
Specifications
EJU34542
Specifications
Watercraft capacity:
Maximum people on board:
3 person
Maximum load capacity:
240 kg (530 lb)
Dimensions:
Length:
3370 mm (132.7 in)
Width:
1230 mm (48.4 in)
Height:
FX SHO 1160 mm (45.7 in)
FX Cruiser SHO 1240 mm (48.8 in)
Dry weight:
FX SHO 376 kg (829 lb)
FX Cruiser SHO 381 kg (840 lb)
Performance:
Maximum fuel consumption:
71.3 L/h (18.8 US gal/h) (15.7 Imp.gal/h)
Cruising range at full throttle:
0.98 hour
Trolling speed:
1250 ±100 r/min
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Number of cylinders:
4
Engine displacement:
1812 cm³
Bore & stroke:
86.0 × 78.0 mm (3.39 × 3.07 in)
Compression ratio:
8.6 : 1
Valve clearance-intake (cold):
0.14–0.23 mm (0.0055–0.0091 in)
Valve clearance-exhaust (cold):
0.28–0.37 mm (0.0110–0.0146 in)
Lubrication system:
Wet sump
Cooling system:
Water
Starting system:
Electric
Ignition system:
T.C.I.
Spark plug:
LFR6A
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Battery capacity:
12 V, 19.0 Ah
Charging system:
Flywheel magneto
Drive unit:
Propulsion system:
Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation:
Counterclockwise
Jet thrust nozzle angle:
24.0+24.0 °
Jet thrust nozzle trim angle:
-10, -5, 0, 5, 10 °
Fuel and oil:
Recommended fuel:
Regular unleaded gasoline
Minimum octane rating (PON):
86
Minimum octane rating (RON):
90
Recommended engine oil type SAE:
SAE 10W-30, 10W-40, 20W-40, 20W-50
Recommended engine oil grade API:
API SE,SF,SG,SH,SJ,SL
Fuel tank total capacity:
70 L (18.5 US gal) (15.4 Imp.gal)
Engine oil quantity with oil filter replacement:
3.1 L (3.28 US qt) (2.73 Imp.qt)
Engine oil quantity without oil filter replacement:
3.0 L (3.17 US qt) (2.64 Imp.qt)
Engine oil total quantity:
4.3 L (4.55 US qt) (3.78 Imp.qt)
102
UF1W10E0.book Page 103 Monday, November 26, 2007 3:57 PM
Trouble recovery
EJU34560
Troubleshooting
If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.
EJU36981
Troubleshooting chart
TROUBLE
Engine does not
start (Starter motor
does not turn over)
POSSIBLE CAUSE
Lock mode selected
Select unlock mode
Engine shutoff switch
Clip not in place
Install clip
Fuse
Burned out
Replace fuse and
check wiring
108
Run down
Recharge
99
Poor terminal connections
Tighten as required
Starter motor
41
33
99
Terminal corroded
Clean
87
Faulty
Have serviced by
Yamaha dealer
—
Throttle lever
Squeezed
Release
34
Fuel
Empty
Refill as soon as possible
60
Stale or contaminated
Have serviced by
Yamaha dealer
93
Water or dirt present
Have serviced by
Yamaha dealer
93
96
Fuel tank
Spark plug
Fouled or defective
Clean or replace
Spark plug
cap
Not connected or
loose
Connect properly
Connected to wrong
cylinder
Connect properly
Fuel pump faulty
Have serviced by
Yamaha dealer
Fuel injection system
103
PAGE
Yamaha Security System
Battery
Engine does not
start (Starter motor
turns over)
REMEDY
96
96
—
UF1W10E0.book Page 104 Monday, November 26, 2007 3:57 PM
Trouble recovery
TROUBLE
Engine runs irregularly or stalls
POSSIBLE CAUSE
REMEDY
PAGE
Empty
Refill as soon as possible
60
Stale or contaminated
Have serviced by
Yamaha dealer
93
Water or dirt present
Have serviced by
Yamaha dealer
93
96
Fuel
Fuel tank
Spark plug
Fouled or defective
Replace
Incorrect heat range
Replace
96
Gap incorrect
Adjust
96
Loose
Connect properly
96
Cracked, torn, or
damaged
Have serviced by
Yamaha dealer
—
Electrical wiring
Loose connection
Have serviced by
Yamaha dealer
—
Fuel injection system
Faulty or clogged injectors
Have serviced by
Yamaha dealer
—
Fuel level
Empty
Refill as soon as possible
60
Oil pressure
warning
Oil pressure dropped
Have serviced by
Yamaha dealer
51
Engine overheated
Jet intake clogged
Clean
Check engine
warning
Faulty sensors
Have serviced by
Yamaha dealer
Spark plug
cap
Warning light or indicator blinks
106
52
104
UF1W10E0.book Page 105 Monday, November 26, 2007 3:57 PM
Trouble recovery
TROUBLE
Watercraft slow or
loses power
POSSIBLE CAUSE
Shift lever
Yamaha Security System
Cavitation
Push lever forward
until it stops
Low-RPM mode selected
Select normal mode
PAGE
36
42
Jet intake clogged
Clean
106
Impeller damaged or
worn
Have serviced by
Yamaha dealer
106
Engine overheat warning
Engine speed reduction control activated
Clean jet intake and
cool engine
51
Oil pressure
warning
Engine speed reduction control activated
Add oil
Spark plug
105
REMEDY
Not completely shifted into forward position
51
Fouled or defective
Replace
Incorrect heat range
Replace
96
96
Gap incorrect
Adjust
96
Spark plug
cap
Loose
Connect properly
Electrical wiring
Loose connection
Have serviced by
Yamaha dealer
—
Fuel
Stale or contaminated
Have serviced by
Yamaha dealer
93
Air filter
Clogged
Have serviced by
Yamaha dealer
94
Oil buildup
Have serviced by
Yamaha dealer
94
96
UF1W10E0.book Page 106 Monday, November 26, 2007 3:57 PM
Trouble recovery
EJU34620
Emergency procedures
EJU34630
contact with the rotating parts of the jet
pump.
Cleaning the jet intake and impeller
If weeds or debris get caught in the jet intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine speed
rises. If this condition is allowed to continue,
the engine will overheat and may seize. If
there is any sign that the jet intake or impeller
is clogged with weeds or debris, return to
shore and check the intake and impeller. Always stop the engine before beaching the watercraft.
EWJ00780
WARNING
Before attempting to remove weeds or debris from the jet intake or impeller area,
shut the engine off and remove the clip
from the engine shut-off switch. Severe injury or death could result from coming in
ECJ00650
CAUTION:
If weeds or debris get caught in the jet intake, do not operate the watercraft above
trolling speed until they have been removed.
(1) Turn the watercraft on its side as shown.
106
UF1W10E0.book Page 107 Monday, November 26, 2007 3:57 PM
Trouble recovery
ECJ00660
CAUTION:
●
●
●
Place a suitable clean cloth or carpeting
underneath the watercraft to protect it
from abrasions and scratches.
Always turn the watercraft over onto its
port (left) side.
When turning the watercraft on its side,
support the bow so that the handlebars
are not bent or damaged.
(2) Remove any weeds or debris from
around the drive shaft, impeller, jet pump
housing, and jet thrust nozzle.
If debris is difficult to remove, consult a
Yamaha dealer.
ECJ00670
CAUTION:
Always avoid operating your watercraft in
areas where weed growth is thick. If traveling in weeded areas is unavoidable, operate the engine alternately at partial throttle
and full throttle. Weeds tend to accumulate more at a steady speed and at trolling
speed. If weeds clog the jet intake or impeller area and cause cavitation, follow the
cleaning procedure above.
egg, or vegetable oil. Call a physician immediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an enclosed space, make sure that it is well ventilated. Always shield your eyes when
working near batteries.
KEEP OUT OF THE REACH OF CHILDREN.
EJU34661
Connecting the jumper cables
(1) Connect the positive (+) jumper cable to
the positive (+) battery terminals of both
batteries.
(2) Connect one end of the negative (–)
jumper cable to the negative (–) battery
terminal of the booster battery.
(3) Connect the other end of the negative (–)
jumper cable to an engine hanger.
2
3
1
EJU34640
Jumping the battery
If the watercraft battery has run down, the engine can be started using a 12-volt booster
battery and jumper cables.
EWJ00790
WARNING
Battery electrolyte is poisonous and dangerous, causing severe burns, etc. Electrolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
107
4
1
2
3
4
Positive (+) jumper cable
Negative (–) jumper cable
Booster battery
Engine hanger
ECJ00680
CAUTION:
Do not connect the end of the negative (–)
jumper cable to the negative (–) battery
terminal of the watercraft battery! Make
sure that all connections are secure and
UF1W10E0.book Page 108 Monday, November 26, 2007 3:57 PM
Trouble recovery
correct before attempting to start the engine. Any wrong connection could damage the electrical system.
(4) Replace the blown fuse with the spare
fuse of the correct amperage by using the
fuse puller on the reverse side of the cap.
(4) Start the engine, and then disconnect the
jumper cables by reversing the steps
above.
1
3
ECJ00480
CAUTION:
●
●
Never push the start switch while the engine is running.
Do not operate the start switch for more
than 5 seconds, otherwise the battery
will be discharged and the engine will
not start. Also, the starter motor could
be damaged. If the engine does not start
in 5 seconds, release the start switch,
wait 15 seconds, and then try again.
4
2
1
2
3
4
Electrical box
Cap
Fuse
Spare fuse
EJU36990
Replacing the fuses
The fuses are located in the electrical box.
To replace a fuse:
(1) Remove the seats. (See page 30 for seat
removal and installation procedures.)
(2) Remove the electrical box cover.
1
1 Fuse puller
1 Electrical box cover
(3) Remove the cap on the electrical box.
Fuse amperage:
Battery fuse:
30 A
Main relay drive fuse:
10 A
Electronic throttle valve fuse:
10 A
Security system fuse:
3A
Main fuse:
20 A
108
UF1W10E0.book Page 109 Monday, November 26, 2007 3:57 PM
Trouble recovery
EWJ00800
EWJ00810
WARNING
Do not use fuses of higher amperage than
recommended. Substitution with a fuse
that has an improper rating can cause extensive electrical system damage and possible fire.
(5) Install the cap.
(6) Install the electrical box cover.
(7) Install the seats.
EJU34710
Towing the watercraft
If the watercraft becomes inoperative in the
water, it can be towed to shore.
If the watercraft must be towed in an emergency using a towline, the operator should
ride the watercraft, holding onto the handlebars.
ECJ00720
CAUTION:
●
●
●
Tow the watercraft at 5 mph (8 km/h) or
less, otherwise water could enter the engine through the exhaust passages or
through the air intake and flood the engine compartment if it is towed too fast.
Tow the watercraft using the bow eye
only.
The bow must be kept up out of the water during towing to prevent water from
entering the engine compartment.
WARNING
●
●
●
The watercraft should only be towed in
an emergency.
The towline should be long enough so
that the watercraft will not collide with
the towing boat when slowing down. A
good rule of thumb is a towline that is
three times the combined length of the
towing boat and the watercraft.
The operator of the towing boat must
keep speed to a minimum and avoid traffic or obstacles which could be a hazard
to the rider on the watercraft.
EJU37000
Submerged watercraft
If the watercraft is submerged or flooded with
water, follow the procedure below and consult
a Yamaha dealer as soon as possible. Failure
to do so could result in serious engine damage!
In an emergency:
(1) Beach the watercraft and remove the
stern drain plugs to drain the water from
the engine compartment. (See page 65
for more information.)
Remove the storage compartment drain
plugs to drain the water from each storage compartment.
(2) Install the stern drain plugs.
(3) Have the watercraft inspected by a
Yamaha dealer as soon as possible.
ECJ00790
CAUTION:
Be sure to have a Yamaha dealer inspect
the watercraft. Otherwise, serious engine
damage could result.
1 Bow eye
109
UF1W10E0.book Page 110 Monday, November 26, 2007 3:57 PM
Consumer information
EJU34780
Limited warranty
YAMAHA MOTOR CORPORATION, U.S.A.
WATERCRAFT LIMITED WARRANTY
Yamaha Motor Corporation is proud of its heritage and reputation for producing products with high standards of quality and workmanship. Product excellence provides the cornerstone for our commitment to customer satisfaction. The Yamaha Watercraft Limited Warranty is your assurance of this commitment.
This warranty provides you with protection against the expense of repairs for your watercraft that are required as a result of defects in
materials or workmanship. When maintained and utilized in the prescribed manner, you can count on your Yamaha watercraft to provide reliable service.
This warranty provides you with specific coverage and notes your responsibilities in maintaining and operating your watercraft.
Please take the time to read and become familiar with this warranty.
PERIOD OF WARRANTY. Any new Yamaha watercraft purchased for pleasure use from an authorized Yamaha dealer in the United
States, will be warranted against defects in material or workmanship for a period of one (1) year from date of purchase, subject to
exclusions noted herein. Any Yamaha Watercraft purchased and utilized for commercial applications will be warranted for a period of
ninety [90] days from the date of purchase, subject to exclusions noted herein. Replacement parts used in warranty repairs will be warranted for the balance of the applicable warranty period.
The warranty described here applies to watercrafts purchased and registered for use in the United States only. For warranty provisions
outside the United States, contact the particular country’s local Yamaha distributor.
OBTAINING REPAIRS UNDER WARRANTY. During the period of warranty, any authorized Yamaha dealer will, free of charge, repair
or replace, at Yamaha’s option, any parts adjudged defective by Yamaha due to faulty workmanship or material from the factory. All
parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.
CUSTOMER’S RESPONSIBILITY. Under the terms of this warranty, the customer will be responsible for ensuring that the watercraft is
properly operated, maintained, and stored as specified in the applicable Owner’s/Operator’s Manual.
The owner of the watercraft shall give notice to an authorized Yamaha dealer of any and all apparent defects within ten [10] days of discovery and make the watercraft available at that time for inspection and repairs at the dealer’s place of business.
GENERAL EXCLUSIONS FROM WARRANTY. This warranty will not cover the repair of damage if the damage is a result of abuse or
neglect of the product. Examples of abuse and neglect include, but are not limited to:
1. Racing or competition use, modification of original parts abnormal strain.
2. Lack of proper maintenance and off season storage as described in the Owner’s/Operator’s Manual, installation of parts or accessories that are not equivalent in design and quality to genuine Yamaha parts.
3. Use of lubricants, oils, and fuel/oil mixtures that are not suitable for watercraft motor use.
4. Damage as a result of accidents, collisions, contact with foreign materials, or submersion.
5. Growth of marine organisms on motor or hull surfaces.
6. Normal deterioration.
7. Gel coat stress cracks.
SPECIFIC PARTS EXCLUDED FROM WARRANTY.
Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not
covered by warranty. Charges for transporting the watercraft to and from an authorized Yamaha dealer are excluded from warranty coverage.
TRANSFER OF WARRANTY. Transfer of the warranty from the original purchaser to any subsequent purchaser is possible by having
the watercraft inspected by an authorized Yamaha dealer and requesting the dealer to submit a change of registration to Yamaha Motor
Corporation. U.S.A. within ten [10] days of the transfer.
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS
STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS
WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS
OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE EXCLUSION MAY NOT APPLY TO YOU.
110
UF1W10E0.book Page 111 Monday, November 26, 2007 3:57 PM
Consumer information
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE.
YAMAHA MOTOR CORPORATION, U.S.A.
Post Office Box 6555
Cypress, California 90630
WARRANTY QUESTIONS AND ANSWERS
Q. What costs are my responsibility during the warranty period?
A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages.
Q. What are some examples of “abnormal” strain, neglect, or abuse?
A. These terms are general and overlap each other in areas. Specific examples include:
Running the watercraft out of oil, operating the machine with a broken or damaged part which causes another part to fail, and so
on. If you have any specific questions on operation or maintenance, please contact your Yamaha dealer for advice.
Q. Does the warranty cover incidental costs such as transportation due to a failure?
A. No. The warranty is limited to repair of the watercraft itself.
Q. May I perform any or all of the recommended maintenance shown in the Owner’s/Operator’s Manual instead of having the dealer do
them?
A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s/Operator’s and Service Manual. We do recommend, however, that items requiring special or equipment be done by a Yamaha dealer.
Q. Will the warranty be void or cancelled if I do not operate or maintain my new watercraft exactly as specified in the Owner’s/Operator’s Manual?
A. No. The warranty on a new watercraft cannot be “voided” or “cancelled”. However, if a particular failure is caused by operation
or maintenance other than as shown in the Owner’s/Operator’s Manual, that failure may not be covered under warranty.
Q. What responsibility does my dealer have under this warranty?
A. Each Yamaha dealer is expected to:
1. Completely set up each new watercraft before sale.
2.
Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at
any later date. In addition, each Yamaha dealer is held responsible for his setup, service and warranty repair work.
Q. Is the warranty transferable to second owners?
A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an
authorized Yamaha dealer for the policy to remain effective.
CUSTOMER SERVICE
If your watercraft requires warranty service, you must take it to any authorized Yamaha dealer within the continental United States. Be
sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regarding warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the
best position to help you. If you are still not satisfied and require additional assistance, please write:
YAMAHA MOTOR CORPORATION U.S.A.
CUSTOMER RELATIONS DEPARTMENT
P.O. Box 6555
Cypress, California 90630
CHANGE OF ADDRESS
The federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibility
of a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by
the selling dealer at the time of your purchase.
If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing
your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new
mailing address.
Mail to:
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
Attention: Warranty Department
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.
111
UF1W10E0.book Page 112 Monday, November 26, 2007 3:57 PM
Consumer information
EJU34800
YAMAHA EXTENDED SERVICE (Y.E.S.)
Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended
Service (Y.E.S.).
•
Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner
satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.
•
Y.E.S. is flexible. You choose the plan that is right for you: 12 months, 24 months, 36 months, or
(on four-stroke models) 48 months beyond your warranty period.
•
Y.E.S. is designed and administered by the same Yamaha people who handle your warranty—
and it shows in the comprehensive coverage benefits. There are no mileage limitations. Coverage is not limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers
manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to
see how comforting uninterrupted factory-backed protection can be.
•
You do not have to pay anything for covered repairs. There is no deductible to pay, and repairs
are not “pro-rated.” You do not have any “out-of-pocket” expenses for covered repairs.
•
In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost.
TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses you
incur because your Yamaha needs covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as
covered repairs during your entire Y.E.S. plan period.
•
Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.
•
Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your
Yamaha much more valuable!
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while
your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha
dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha
Extended Service.
We urge you to act now. You will get the excellent benefits of TRIP coverage right away, and you
will rest easy knowing you will have strong factory-backed protection even after your Yamaha
Limited Warranty expires.
A special note:
If visiting your dealer is not convenient, contact Yamaha with your Primary ID number (your Owner’s
Manual shows you where to find this number). We will be happy to help you get the Y.E.S. coverage
you need.
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD
(1-866-937-3983)
112
UF1W10E0.book Page 1 Monday, November 26, 2007 3:57 PM
Index
A
Air filter element ....................................... 94
Analog speedometer/tachometer ............. 46
Analog speedometer/tachometer and
indicator lights....................................... 46
Approval label of emission control
certificate ................................................ 2
B
Battery................................................ 66, 87
Battery, checking...................................... 99
Battery, jumping ..................................... 107
Beaching the watercraft ........................... 83
Beverage holder....................................... 58
Bilge ......................................................... 65
Boarding alone ......................................... 77
Boarding and starting from a dock ........... 77
Boarding and starting in deep water ........ 77
Boarding and starting in shallow water .... 76
Boarding with passengers........................ 78
Bow down................................................. 38
Bow eye ................................................... 39
Bow up ..................................................... 38
C
Capsized watercraft ................................. 80
Check engine warning indicator ............... 52
Cleaning the watercraft ............................ 88
Cooling water pilot outlets .................. 34, 70
Cruise assist............................................. 44
Cruising limitations ................................... 11
D
Digital speedometer ................................. 49
Docking the watercraft ............................. 83
E
Emergency procedures .......................... 106
Emission control information ...................... 2
Engine break-in ........................................ 71
Engine compartment ................................ 63
Engine oil ................................................. 60
Engine oil and oil filter .............................. 93
Engine oil level ......................................... 63
Engine overheat warning indicator........... 51
Engine serial number ................................. 1
Engine shut-off cord ................................. 70
Engine shut-off switch .............................. 33
Engine stop switch ................................... 33
Enjoy your watercraft responsibly ............ 25
F
Fire extinguisher....................................... 67
Flushing the cooling system ..................... 86
Front storage compartment ...................... 56
Fuel and oil............................................... 59
Fuel injection system.............................. 101
Fuel level .................................................. 63
Fuel level meter........................................ 49
Fuel level warning indicator...................... 50
Fuel system .............................................. 87
Fuel system, checking.............................. 93
Fuel tank .................................................. 93
Fuel tank filler cap .................................... 31
Fuel tank, filling ........................................ 60
Fuses, replacing ..................................... 108
G
Gasohol .................................................... 59
Gasoline ................................................... 59
Getting to know your watercraft ............... 74
Glove compartment .................................. 56
H
Handgrip................................................... 39
Hazard information ................................... 16
Hood......................................................... 31
Hour meter/voltmeter ............................... 50
Hull and deck ........................................... 63
Hull Identification Number (HIN)................. 1
I
Identification numbers ................................ 1
Important labels.......................................... 5
J
Jet intake .................................................. 69
Jet intake and impeller, cleaning ............ 106
Jet thrust nozzle angle, checking ............. 94
Jumper cables, connecting .................... 107
L
Labels, other .............................................. 8
Labels, warning .......................................... 6
Launching the watercraft .......................... 72
Learning to operate your watercraft ......... 74
Leaving the watercraft .............................. 74
Left multifunction display and
operation buttons .................................. 48
UF1W10E0.book Page 2 Monday, November 26, 2007 3:57 PM
Index
Limitations on who may operate
the watercraft ........................................ 10
Limited warranty..................................... 110
“L-MODE” indicator light........................... 48
Lubrication................................................ 87
Lubrication points ..................................... 98
M
Main components, location of .................. 26
Maintenance and adjustments ................. 89
Manufactured date label............................. 3
Multifunction information center ......... 45, 71
N
No-wake mode ......................................... 42
“NO-WAKE MODE” switch....................... 34
O
Oil pressure warning indicator.................. 51
Operating your watercraft......................... 74
Operation ................................................. 71
Operation of controls and
other functions ...................................... 30
Operation requirements ........................... 13
Owner’s/operator’s manual and tool kit.... 89
P
Periodic maintenance chart...................... 91
Post-operation care.................................. 84
Pre-operation check list............................ 61
Pre-operation check points ...................... 63
Pre-operation checks ............................... 61
Primary Identification (PRI-ID) number ...... 1
Pull-up cleats (for FX Cruiser SHO) ......... 40
Q
Quick Shift Trim System (QSTS) ............. 69
Quick Shift Trim System (QSTS)
selector ................................................. 37
R
Reboarding step....................................... 39
Recommended equipment ....................... 15
Remote control transmitter....................... 32
Reverse on waterways............................. 83
Riding with passengers ............................ 75
Right multifunction display and
operation buttons
(for FX Cruiser SHO) ............................ 52
Rough water operation............................. 83
“RPM” indicator light................................. 47
Rules of the Road .................................... 20
S
Seat storage compartment ....................... 57
Seats ........................................................ 30
Selecting the operation mode .................. 42
“SET” switch ............................................. 34
Shift cable, checking ................................ 94
Shift lever ................................................. 36
Shift lever and reverse gate ..................... 68
Spark plugs, cleaning and adjusting ........ 96
“SPEED” indicator light ............................ 47
Star labels .................................................. 3
Start switch............................................... 34
Starting the engine ................................... 72
Starting the watercraft .............................. 76
Steering system ................................. 35, 67
Stern drain plugs ...................................... 66
Stern eyes ................................................ 40
Stopping the engine ................................. 74
Stopping the watercraft ............................ 82
Storage..................................................... 86
Storage compartments ............................. 55
Submerged watercraft ............................ 109
Switches ................................................... 70
Switches, right handlebar ......................... 34
T
Throttle cable, checking and adjusting ..... 95
Throttle lever ...................................... 34, 67
Tilt lever.................................................... 36
To get more boating safety information.... 24
Towing the watercraft ............................. 109
Transporting ............................................. 85
Trolling speed, checking ........................ 101
Troubleshooting ..................................... 103
Troubleshooting chart ............................ 103
Turning the watercraft .............................. 81
U
“UNLOCK” indicator light.......................... 48
Up and down switches ............................. 34
W
“WARNING” indicator light ....................... 48
Water separator ....................................... 64
Watercraft characteristics......................... 16
Water-skiing ............................................. 18
Watertight compartment ........................... 58
UF1W10E0.book Page 3 Monday, November 26, 2007 3:57 PM
Index
Y
Yamaha Engine Management
System (YEMS) .................................... 40
YAMAHA EXTENDED SERVICE
(Y.E.S.) ............................................... 112
Yamaha Security System......................... 40
Yamaha Security System settings ........... 41
UF1W10E0.book Page 4 Monday, November 26, 2007 3:57 PM
YAMAHA MOTOR CORPORATION, USA
Printed in USA
January 2008–4.0 × 1 CR
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement