AKO H 260/4 Installation And Operating Instructions

Add to My manuals
4 Pages

advertisement

AKO H 260/4 Installation And Operating Instructions | Manualzz

H 260/4

Installation and

Operating Instructions

Fan Heater

03/15/B Bestell-Nr. / Order no. / No de commande: INAEF12WRG Issue1

H 260/4

1. Information for the user

Dear customer, read all information contained in this manual carefully.

Keep these instructions in a safe place and pass them on to any new owner.

ATTENTION!

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision!

ATTENTION!

Children of less than 3 years should be kept away unless continuously supervised!

ATTENTION!

Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved!

ATTENTION!

Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance!

ATTENTION!

Some parts of this product can become very hot and cause burns! Particular attention has to be given where children and vulnerable people are present!

ATTENTION!

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard!

ATTENTION!

The heater must not be located above or below a socket outlet!

ATTENTION!

In order to avoid overheating, do not cover the heater!

ATTENTION!

The heater carries the warning symbol indicating that it must not be covered!!

To ensure safe operation, the heater may only be installed and connected in accordance with these installation and operating instructions.

The installation of this heater must be carried out by a competent electrician in accordance with the current safety regulations.

The heater may only be used for heating room air in enclosed spaces.

Repairs to the appliance, or any other interventions, may only be performed by qualified persons or the after-sales customer service.

In the event of any defect or during extended periods of non-use, the heater must be disconnected from the power supply. Deactivate or remove fuse.

Do not use the appliance in areas where flammable gases or liquids are stored or used.

ATTENTION!

Do not place the power supply cord over the heater!

ATTENTION!

If the appliance is switched on automatically while unattended, potential hazards may exist, e.g. appliances that have been covered or obstructed in your absence may pose a risk of fire!

ATTENTION!

Install the device such that it is not possible for someone in the bath or shower to touch the control element!

ATTENTION!

In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer or connected to a circuit that is regularly switched on and off by the utility.

www.dimplex.de/en H_260_4_gb · 03/15/B EN-5

H 260/4

2. Technical data

Heat output

Supply voltage

Degree of protection

Safety class

2000 W

1/N/PE~, 230 V, 50 Hz

IP24

I (with protective conductor)

Dimensions (W x H x D) 300 x 405 x 120 mm

Weight 3,25 kg

19

0

308

3. Installation

The heater must only be installed and operated on a vertical wall as shown.

Installation below a wall socket is not permissible.

The device plug must be accessible after installation.

It is not permissible to install the device in protection zones as defined in the relevant standards.

In addition, a minimum clearance of 750 mm between inflammable objects e.g. curtains, towels or heat-sensitive plastics, and the front of the unit must be maintained.

The device is mounted to the wall with 3 screws. The enclosed plastic bag contains screws and dowels.

Observe the minimum clearances! Dimensions in mm.

250 300 280

405

250

3.1 Mounting Instruction

 Unlock the wall bracket (A) and remove from the device.

Drill mounting holes for the wall bracket and insert the dowels.

Align the wall bracket and firmly screw it onto the wall.

Hang the device on the wall mount.

Pivot down the heater and push into place (B).

B

A

4. Electrical Connection

The voltage marked on the type plate must correspond to the supply voltage (A.C supply only).

5. Heating operation

5.1 All Models

The room temperature is regulated using the adjustable thermostat (A). If the rotary knob is set to the lowest setting i.e. to the extreme left (see figure), the thermostat switches the heater on at an ambient temperature of approx. 5°C.

A

ATTENTION!

Rooms can become overheated if left unattended whilst being heated; this depends on the size of the room, its heating requirements and the setting of the thermostat. Persons who are not able to vacate the room if the temperature becomes too high can thus be placed in danger.

5.2 Models with 60-minute timer

Turn the timer knob (B) in a clockwise direction. Set the desired time period (up to 60 minutes).

During the time set, the device runs at its full output of

2000 W. The thermostat is deactivated. When the set time has expired, the device switches to a lower

(1000 W) heating level, which is controlled by the thermostat.

B

The set time can be changed or reversed at any time using the timer knob (B).

EN-6 H_260_4_gb · 03/15/B www.dimplex.de/en

H 260/4

5.3 Models with 24-hour timer

The operating hours of the heater can be set in a day program (24 hours) using the timer.

For automatic operation, slide the switch (C) to the right into "clock" position.

Setting the time:

Turn timer (D) clockwise until the marking matches up to the current time.

Heater ON: Slide segments outwards.

Heater OFF: Slide segments inwards.

Each segment represents a switch-on or switch-off time of 20 minutes. In order, for example, to set a switch-on time of one hour, 3 segments are slid outwards.

The timer can be programmed for several ON/

OFF phases of different lengths. The thermostat provides a uniform room temperature during the switch-on time.

Outside of the switching time, no heating operation - and thus no frost protection - takes place.

E

D

C

Manual OFF Timer

Operation via the timer can be deactivated at any time by switching to "Manual" or "0" (OFF).

The timer only runs when the device is connected to the power supply.

6. Protection Against Overheating

If the permissible temperature is exceeded, the heater switches off automatically. If this occurs, pull the mains plug out and leave the device unplugged for a few minutes, so that the temperature limiter can switch back again.

Then remove the cause, e.g. when the air grid is blocked or covered. When the device has cooled sufficiently, it can be started up again.

7. Faults

If the heater does not give off heat, check the following points:

Has the thermostat been set to the desired temperature?

Has the overheat protection been triggered? See chapter 6!

Is the fuse in the fuse box switched on?

Models with 24-hour timer: Set the slide switch and segments correctly - see Chapter 5.3.

If the fault cannot be corrected, please contact a specialist electrical service center or else your nearest after-sales service.

To process your order, please state the production number (E No.) and manufacturing date (FD) of the device. This information is listed on the type plate.

The device must only be repaired or manipulated by a skilled electrician or the after-sales service.

8. Cleaning

To clean the device, first disconnect it from the mains and allow it to cool down. Clean the outside of the unit using a soft, damp cloth. Do not use scouring powder or furniture polish as this may damage the surface.

Dust which gathers inside the device can be removed from the outside using a vacuum cleaner.

9. Warranty

Please contact your local dealer for information on customer service and warranty conditions.

10. Note on Disposal

Do not dispose of the unit with general household waste. The device must be taken to a local waste disposal plant.

Glen Dimplex Deutschland GmbH

Am Goldenen Feld 18

D-95326 Kulmbach

Subject to modifications www.dimplex.de/en

Phone: +49 9221 709-564

Fax: +49 9221 709-589

E-Mail: [email protected]

www.dimplex.de/en

H_260_4_gb · 03/15/B EN-7

advertisement

Related manuals

Download PDF

advertisement