3xLogic VX-VT-20, VX-VT-36 Hardware And Installation Manual
Advertisement
Advertisement
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
VISIX V-Series All-in-One Cameras - Gen I
Hardware and Installation Manual
2018-3
10385 Westmoor Drive, Suite 210, Westminster, CO 80021 | www.3xlogic.com | (877) 3XLOGIC 1
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
This manual applies to the following camera models. Please use the below links or the Table of Contents to locate the section of this manual that pertains to your particular All-in-One camera model:
Camera Type
Exterior Bullet Camera
Exterior Bullet Camera w/Remote Focus
Exterior Dome Camera
Model
VX-2A-B-RIWDZ (New), VX-2A-B-IWD (DC)
VX-2VA-B-RIWD (New), VX-2A-B-RIWD (DC)
VX-2AD3B-IWD (New), VX-2AD3-IWD (DC)
Interior Mini Dome Camera
VERA 20°, 36° or 50° Field-of-Vision Thermal Bullet
Camera
Interior Pinhole Camera
VX-2A-IMD-X
VX-VT-20, VX-VT-36, VX-VT-58 (New)
VX-2V28-PIN
Please use the links above or the Table of Contents to locate the section of this manual that pertains to your particular All-in-One camera model.
Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer.
This manual may contain technical inaccuracies or printing errors. The content is subject to change without notice. The manual will be amended if there are any hardware updates or changes.
Disclaimer Statement
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s
Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
”
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 2
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information, see: www.recyclethis.info
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 3
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
WARNING : Serious injury or death may be caused if any of these warnings are neglected.
CAUTION : Injury or equipment damage may be caused if any of these cautions are neglected.
WARNINGS:
Please adopt a power adapter which can meet the safety extra low voltage (SELV) standard when possible, and source with 12 VDC or 24 VAC (depending on models) according to the
IEC60950-1 and Limited Power Source standard. Before applying power to the camera, check the power source to ensure that it is within the specifications
If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture unless it is an exterior/weatherproof model. Please do not install the camera in a place exposed to direct sunlight. Do not operate the camera in environments beyond the specified temperature. Refer to your specific camera model’s section of this m anual for environmental conditions and limitations.
This installation should be made by a qualified service person and should conform to all the local codes.
Please install blackout equipment into the power supply circuit to prevent footage and data loss .
Please make sure that the ceiling can support more than 50(N) Newtons of gravity if the camera is fixed to the ceiling.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 4
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
CAUTIONS:
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal damage to the camera.
The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface of the sensor not be exposed to the laser beam.
Do not place the camera in extremely hot, cold temperatures (the operating temperature should be between -30°C ~ 60°C, or 40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp environment, and do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
Keep the camera away from water and any liquid.
While shipping, the camera should be packed in its original packing.
Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type.
NOTE: For cameras that support IR, you are required to pay attention to the following precautions to prevent IR reflection.
► Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. (only applies to certain models).
►
►
Make certain the installation location does not have reflective surfaces of objects too close to the camera. The IR light from the camera may reflect back into the lens causing reflection. (only applies to certain models).
The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly (only applies to certain models).
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 5
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Table of Contents
1 VISIX V-SERIES ALL-IN-ONE CAMERAS ............................................................................................ 8
1.1
I NTRODUCTION ................................................................................................................................. 8
2 VX-2A-B-RIWDZ / VX-2VA-B-RIWD - 2MP EXTERIOR BULLET CAMERA ........................................... 9
2.1
VX-2A-B-RIWDZ/ VX-2-VA-B-RIWD S PECIFICATIONS Q UICK S UMMARY ............................................... 9
2.2
P ACKAGE C ONTENTS ........................................................................................................................ 10
2.3
P ART N AMES .................................................................................................................................. 11
2.4
I NSTALLATION ................................................................................................................................. 12
2.4.1
Installing the Camera – Installation without Bracket ......................................................... 12
2.4.2
Adjusting angle of the camera ............................................................................................ 14
2.4.3
Adjusting Zoom and Focus (VX-2A-B-IWD Model Only) ...................................................... 14
2.5
C ONNECTIONS ................................................................................................................................ 15
2.6
F ULL C AMERA S PECIFICATIONS ........................................................................................................... 17
2.7
C AMERA D IMENSIONS ...................................................................................................................... 19
3 VX-2AD3B-IWD / VX-2AD3-IWD - 2 MP EXTERIOR DOME CAMERA .............................................. 20
3.1
VX-2AD3B-IWD S PECIFICATIONS Q UICK S UMMARY ........................................................................... 20
3.2
P ACKAGE C ONTENTS ........................................................................................................................ 21
3.3
P ART N AMES .................................................................................................................................. 22
3.4
I NSTALLATION ................................................................................................................................. 23
3.4.1
Installing the Camera – Installation without Bracket ......................................................... 23
3.4.2
Reattachment of Dome Cover – Alignment ........................................................................ 25
3.4.3
Adjusting angle of the camera ............................................................................................ 25
3.4.4
Connections ........................................................................................................................ 26
3.5
F ULL C AMERA S PECIFICATIONS ........................................................................................................... 27
3.6
C AMERA D IMENSIONS ...................................................................................................................... 29
3.7
C OMPATIBLE A CCESSORY I NSTALLATION (M OUNTS ) ............................................................................... 30
3.7.1
Wall Mount- VX-2AD-WM ................................................................................................. 30
3.7.2
Ceiling Mount- VX-2AD-CM ............................................................................................... 32
3.7.3
Pendant Mount Cap - VX-2AD-PMCB ................................................................................. 34
3.7.4
Gang Box Mount – VX-2AD-GB ........................................................................................... 35
4 VX-2A-IMD-X - 2 MP INTERIOR MINI DOME CAMERA ................................................................... 37
4.1
VX-2A-IMD-X S PECIFICATIONS Q UICK S UMMARY .............................................................................. 37
4.2
P ACKAGE C ONTENTS ........................................................................................................................ 38
4.3
P ART N AMES .................................................................................................................................. 39
4.4
I NSTALLATION ................................................................................................................................. 40
4.4.1
Installing the Camera – Installing without Bracket ............................................................ 40
4.4.2
Adjusting angle of The camera ........................................................................................... 42
4.5
C ONNECTIONS ................................................................................................................................ 42
4.6
F ULL C AMERA S PECIFICATIONS ........................................................................................................... 43
4.7
C AMERA D IMENSIONS ...................................................................................................................... 45
4.8
C OMPATIBLE A CCESSORY I NSTALLATION (M OUNTS ) ............................................................................... 46
4.8.1
Wall Mount - VX-2AIMD-WM ............................................................................................. 46
4.8.2
Location of the Holes for M3x6L Bolts ................................................................................ 48
4.8.3
Ceiling Mount - VX-2AD-CM ............................................................................................... 49
4.8.4
Pendant Mount Cap - VX-2AD-PMC .................................................................................... 51
5 VX-VT-20, VX-VT-36, VX-VT-58 – VERA 20°, 36°, 58° THERMAL BULLET CAMERA .......................... 53
5.1
VX-VT-20, VX-VT-36, VX-VT-58 S PECIFICATIONS – Q UICK S UMMARY .................................................. 53
5.2
P ACKAGE C ONTENTS ........................................................................................................................ 54
5.3
P ART N AMES .................................................................................................................................. 55
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 6
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5.4
I NSTALLATION ................................................................................................................................. 56
5.4.1
Installing The camera – installation without bracket ......................................................... 56
5.4.2
Adjusting angle of The camera ........................................................................................... 58
5.5
C ONNECTIONS ................................................................................................................................ 59
5.6
F ULL C AMERA S PECIFICATIONS ........................................................................................................... 61
5.7
C AMERA D IMENSIONS ...................................................................................................................... 62
6 VX-2V28-PIN – IP PINHOLE CAMERA ............................................................................................ 63
6.1
VX-2V28-PIN S PECIFICATIONS — Q UICK S UMMARY ............................................................................ 63
6.2
P ACKAGE C ONTENTS ........................................................................................................................ 64
6.3
P ART N AMES .................................................................................................................................. 65
6.3.1
Main Unit: ........................................................................................................................... 65
6.3.2
Camera Unit with Conjoined Accessories............................................................................ 66
6.4
I NSTALLATION ................................................................................................................................. 67
6.4.1
Camera Unit Installation ..................................................................................................... 67
6.4.2
Inconspicuous Installation .................................................................................................. 67
6.4.4
Surface Installation for Fixed Angle .................................................................................... 69
6.4.5
Surface Installation for Pan/Tilit Adjustment ..................................................................... 70
6.4.6
MAIN UNIT INSTALLATION .................................................................................................. 71
6.5
C ABLE C ONNECTION ......................................................................................................................... 73
6.5.1
DI/Do Terminal Connector .................................................................................................. 73
6.5.2
Camera Connector .............................................................................................................. 74
6.5.3
LAN Connector .................................................................................................................... 75
6.5.4
Power Connector ................................................................................................................ 75
6.6
C AMERA D IMENSIONS ...................................................................................................................... 76
6.7
F ULL C AMERA S PECIFICATIONS ........................................................................................................... 77
7 POWER OVER ETHERNET SPECIFICATIONS .................................................................................... 79
7.1
P OWER C OMPARISON ...................................................................................................................... 79
8 REVISION HISTORY ....................................................................................................................... 80
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 7
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
1 VISIX V-Series All-in-One Cameras
1.1
Introduction
VISIX V-Series All-in-One, edge-based IP cameras are powerful, full-featured, VMS and advanced analytic capable. VISIX V-Series cameras provide a complete surveillance solution for the small and medium sized businesses and for unique single-point applications.
Several models exist to best suit any number of environments. Hardware installation details for each model are contained within. Use the Table of Contents to locate the Section pertaining to your particular camera model.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 8
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2 VX-2A-B-RIWDZ / VX-2VA-B-RIWD - 2MP
Exterior Bullet Camera
The VX-2A-B-RIWDZ (previous model: VX-2A-B-IWD) and VX-2VA-B-RIWD (previous model: VX-2A-B-
RIWD) are fully functional indoor/outdoor IP cameras with advanced analytics capabilities. These cameras can be connected to a DVR or act as a standalone recording device. The exterior bullet camera line offers high-definition video at full 1920 x 1080 resolution for both indoor and outdoor video surveillance applications which require superior clarity and detail.
The wealth of features includes; dual-streaming of either H.264 or MJPEG compression; wide dynamic range; Micro SD card slot for local recording; IP66 weather resistant construction; varifocal lens; and IR illumination. The RIWD model also features remote one-click auto focus.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to configure a detection rule. These advanced analytics allow for object classification, direction, people counting, dwell times, and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a stand-alone device recording video to the onboard memory card. This makes the camera compatible with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.
2.1
VX-2A-B-RIWDZ/ VX-2-VA-B-RIWD Specifications- Quick
Summary
Component
Camera
Feature Description
SONY EXMOR 1/2.9” 1080p CMOS Image Sensor
True Day / Night
DC Auto Iris Lens
WDR
Embedded IR Illuminator
Weather Proof (IP66)
Remote Zoom/Focus Control (One Click AF) - ** VX-2-VA-B-RIWD
Only**
Video
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC),
MJPEG(Motion JPEG)
Max 30fps in 1080p
Text Overlay
Analog Video Output
Network 10/100 Base-T Ethernet
Integration
General
Video Contents Analysis
(VCA)
ONVIF compliant (Profile S)
Micro SD/SDHC Card Slot x1
Power over Ethernet (PoE)
VCA Presence Standard
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 9
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.2
Package Contents
Please unpack the package carefully and handle the equipment with care. The package contains:
Camera DC Power Adaptor
Universal Plugs Screws(M4x30) and Plastic Anchors
Quick Installation Guide
Silicon Waterproof Band
Hex Wrench(3mm)
Video Output Cable
Installation Template
NOTE: The contents above are subject to change without prior notice.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 10
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.3
Part Names
❶
❷
❺
❻
❹
❸
❼
❽
❿
❾
* Models herein and their appearance are subject to change without any prior notice.
1).
Sunshield: Position the sunshield to prevent direct sunshine.
2).
Video-Out Cable Socket: Socket for the video output cable included in the package (CVBS: 1.0Vp-p /
75Ω BNC)
3).
PAL/NTSC button: Pressing the PAL/NTSC button each time changes the mode as follows: No video output -> PAL-> NTSC
4).
Reset button: Use the button to restart the device or to reset it to Factory Default. Refer to the
3xLOGIC VISIX All-in-One Camera User Manual for more details on restarting/resetting to factory default.
5).
Focus Puller: Use the puller to manually determine correct focus of the camera. Refer to Adjusting
Zoom and Focus for more details.
6).
Zoom Puller: Use the puller to manually determine appropriate field of view of the camera. Refer to
Adjusting Zoom and Focus for more details.
7).
microSD memory card slot: The camera supports up to 32GB. A card with Class 4 and higher is recommended for HD recordings.
8).
Terminal Connector: Connector for cable connection of digital input/output. Refer to Section 2.5:
Connections for more details.
9).
Power Adaptor Connector: Use DC12V for the power supply.
10).
LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 11
Installation template
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.4
Installation
2.4.1
INSTALLING THE CAMERA – INSTALLATION WITHOUT BRACKET
Installation Template
6702 V1.0
NOTE: Installation template ’ s image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package separately.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 12
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Steps:
1).
Place the installation template included in the package on the desired installation surface.
2).
Drill three holes in correct positions based on the template paper, and insert the anchor blocks into the holes.
3).
Attach the silicon waterproof band included in the package to the camera ’ s mounting surface by aligning it with the three alignment holes.
4).
Connect the required cables including a power cable and a LAN cable (or PoE connection) to the device. See
Section 2.5: Connections for a diagram of the correct connections.
5).
Place the camera body to match the three alignment holes with the three anchor blocks, and hold the camera against the surface where the camera will be mounted.
6).
Tighten the anchor blocks with the screws.
7).
Adjust the heading direction of the camera. Refer to
Adjusting Angle of the Camera for more details.
8).
Adjust zoom and focus of the camera. Refer to Adjusting
Zoom and Focus for more details.
9).
Attach the lens cover on the main body by rotating it clockwise
CAUTION: Sealing gaps is recommended as gaps may appear after the camera installation. Gaps may cause problems such as moisture, water leakage, and etc., which negatively affects the operation of the camera if gaps remain unsealed.
CAUTION: To prevent products from damage, place the camera on a stable and non-vibrating surface. If the stability is in doubt, consult safety personnel for reinforcements, and then proceed with the installation.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 13
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.4.2
ADJUSTING ANGLE OF THE CAMERA
Adjust the camera to the desired angle by unscrewing the joints referring to the following pictures.
Adjust the joint to install the camera on the wall.
Tilting adjustment
Steps:
1).
Insert the video output cable (included in the package) to the video output cable socket, and connect it to an analogue video test monitor to check if the camera angle has been set as intended. If the angle is appropriate, disconnect the camera from the analogue monitor, and then remove the video output cable from the camera.
2.4.3
ADJUSTING ZOOM AND FOCUS (VX-2A-B-
IWD MODEL ONLY)
Steps:
1).
Unscrew the zoom puller and the focus puller counter-clockwise.
2).
Adjust the zoom and the focus of the lens.
3).
Tighten the zoom puller and the focus puller again by turning it clockwise after the zoom and the focus are properly adjusted.
Panning adjustment
Video output cable socket
Zoom Puller
Focus Puller
Reset
PAL/NTSC
CAUTION: Manual adjustment of Zoom and Focus is only possible on the VX-2VA-B-IWD model version. Zoom and Focus controls can be configured digitally from the camera’s web interface for VX -2VA-B-RIWD models. See the VISIX V-Series All-in-One Camera User
Manual for more details on adjusting lens settings from the camera’s web interface .
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 14
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.5
Connections
GREEN : DI
WHITE : DI COM
ORANGE : DO
YELLOW : DO COM
❶
❷
LAN cable
(not included)
❸
❹
DC 12V
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 15
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
1).
Sensor (DI) connection: Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor as the following figures. Settings can be done through the camera ’ s webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA.
CAUTION: Do not exceed the maximum input voltage or relay rate.
Internal +3.3V Internal
DI
Output of
Sensor
+ - DI
Output of
Sensor
+ -
COM
COM - +
Relay Type
2).
Alarm (DO) Connection: Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
CAUTION: Do not exceed the maximum relay rating.
Internal
DO
Device
Voltage Type
COM
Relay Type
3).
LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable
(RJ45. to connect the device to a hub or a router in the network. Refer to Section 6: Power over
Ethernet Specifications to for further detail.
4).
Power Connection: The camera can be powered from either 12VDC or PoE. If the camera is powered via PoE, refer to Section 6: Power over Ethernet Specifications for further detail.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 16
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.6
Full Camera Specifications
Camera Module
CMOS
Image Sensor
Effective Pixels
SONY EXMOR 1/2.9
1920x1080
”
Scanning system Progressive scanning
1080p CMOS
Electrical
Resolution 1920 x 1080
Min. Illumination Color: 0.7 lux, BW: 0 lux (IR LED On)
AGC Control Auto
Lens 3.0(w) – 9.0mm(t), F1.5(w) – F2.5(t), Optical 3x
Removable IR Cut Filter Day & Night
Wide Dynamic
Range
Digital WDR
IR Illuminator
IR LED
IR Working
Distance
Video
High Power IR LED x 12 (850nm)
Max. 30m (98ft)
Compression
Format
Number of
Streams
H.264 and MJPEG Selectable per Stream
Dual Stream, Configurable
Resolution
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
Compression FPS 30fps@1080p
Motion Detection Built-in
Burnt-in Text
(Digital)
Time stamp and text caption overlay
Analogue Output NTSC/PAL
Audio
Input/output
Compression
Format
-
-
Function
Digital
Input/Output
RS-485
Network
Power over
Ethernet (PoE)
1/1 channel
Not supported
10/100 Base-T
Supported
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 17
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Function
Protocol
SD Slot
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB -
II), IGMP, ICMP, SSLv2/v3, TLSv1
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
Electrical Characteristics
Power Source
Power
Consumption
Video Output
Audio Input
Audio Output
D/I
D/O
DC 12V / PoE
Max. 6W @ DC 12V
1 Vp-p, 75
, Composite
-
-
Max 50mA@5VDC, TTL level 1.5V threshold
Max 50mA@24VDC
On-state resistance: 50
(max continuous)
Environment Condition
Operating
Temperature
Operating
Humidity
[DC12V] -20°C ~ 50°C (-4°F ~ 122°F)
[PoE] -20°C ~ 50°C (-4°F ~ 122°F)
Up to 85% RH
Mechanical Condition
Material
Color
Aluminum Die-Casting
Ivory
Dimension 83.5mm X 86mm X 287 mm
Weight (Approx.) 860g (1.90lbs)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 18
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2.7
Camera Dimensions
3.39 in. (86 mm)
9.41 in. (239 mm)
11.02 in. (280 mm)
11.30 in. (287 mm)
2.68 in.
(68 mm)
3 x
.197 in. (5mm)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 19
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3 VX-2AD3B-IWD / VX-2AD3-IWD - 2 MP Exterior
Dome Camera
The VX-2AD3B-IWD (previous model: VX-2AD3-IWD) is a fully functional indoor/outdoor IP camera with advanced analytics capabilities. These cameras can be connected to a DVR or act as a standalone recording device.
The exterior dome offers high-definition video at full 1920 x 1080 resolution for both indoor and outdoor video surveillance applications which require superior clarity and detail. Its many features include; dual-streaming of either H.264 or MJPEG compression; wide dynamic range; Micro SD card slot for local recording; IP66 weather resistant construction and IR illumination.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to configure a detection rule. These advanced analytics allow for object classification, direction, people counting, dwell times, and occupancy counts.
When enabled, the embedded VIGIL Server software allows the camera to be run as a stand-alone device recording video to the onboard memory card. This makes the camera compatible with the existing 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or set it up on your mobile device or tablet using our easy to use QR code quick setup.
3.1
VX-2AD3B-IWD Specifications- Quick Summary
Component Feature Description
Camera
1/2.9” 1080p CMOS Image Sensor
True Day/Night
WDR
Embedded IR Illuminator
Video
Network
Integration
General
Video Contents
Analysis (VCA)
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion
JPEG)
Max 30fps in 1080p
Text Overlay
10/100 Base-T Ethernet
ONVIF compliant (Profile S)
Micro SD/SDHC Card Slot x1
Power over Ethernet (PoE)
VCA Presence Standard
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 20
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.2
Package Contents
Please unpack the package carefully and handle the equipment with care. The package contains:
Camera
Camera
Screw(M4x35) & Plastic Anchors
Cable
Camera
Cable
Camera
Camera
Torx Wrench
Camera
Torx Wrench
Camera
Camera
Torx Wrench
O-ring &
Waterproof Bracket
Cable
Cable
Quick Installation Guide
Cable Screw &
Torx (T20) Wrench
Cable
O-ring &
Waterproof Bracket
Screw &
Plastic Anchor-3pcs
Cable
Torx Wrench
Torx Wrench
O-ring &
Waterproof Bracket
Waterproof Bracket
Screw &
Cable
O-ring & Waterproof Bracket
Torx Wrench
O-ring &
Installation Template
Waterproof Bracket
Bottom Pad
Quick Installation Guide
Bottom Pad
Installation Template
O-ring &
Quick Installation Guide
Waterproof Bracket
Installation Template
Installation Template
Bottom Pad
Screw &
Plastic Anchor-3pcs
Waterproof Bracket
Screw &
Plastic Anchor-3pcs
Adaptor & AC Plug
Adaptor & AC Plug
Bottom Pad
O-ring &
Waterproof Bracket
Screw &
Plastic Anchor-3pcs
Quick Installation Guide
Installation Template
Quick Installation Guide
Screw &
Plastic Anchor-3pcs
Installation Template
Adaptor & AC Plug
Quick Installation Guide
NOTE: The contents above are subject to change without prior notice. Installation Template
Bottom Pad
Quick Installation Guide
Installation Template
Bottom Pad
Quick Installation Guide
Installation Template
Adaptor & AC Plug
Adaptor & AC Plug
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 21
Adaptor & AC Plug
Adaptor & AC Plug
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.3
Part Names
❶
❷
Ambient Light Sensor
Ambient Light Sensor
❸
❹
Reset Button
Reset Button
❺
❻
* Models herein and their appearance are subject to change without any prior notice.
1) Safety Wire: The dome cover is attached to the camera body with this safety wire to prevent the dome cover from being dropped.
2) Ambient Light Sensor: Used to detect the level or the intensity of light for the IR operation. The sensor should not be blocked by any object.
3) MicroSD/SDHC Card Slot: Up to 32GB supported. Class 4 and higher recommended for HD recordings.
4) Reset Button: Use the button to restart the device or to reset it to Factory Default. Refer to the
3xLOGIC VISIX All-in-One Camera User Manual for more details on restarting/resetting to factory default.
5) RJ-45: Connect an RJ-45 LAN cable for 10/100 Base-T Ethernet (PoE supported).
6) DC Power Jack: Connect the provided DC12V adaptor for the power supply unless it is PoE powered.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 22
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.4
Installation
3.4.1
INSTALLING THE CAMERA
–
INSTALLATION WITHOUT BRACKET
Installation Template
4.92 in.
(125 mm)
M o unting tem p la te
.255 in. (6.5 mm)
CAUTION: Installation template ’ s image size scale in this installation guide is not 1:1. The correct-size template paper can be found inside the product packaging.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 23
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Steps:
1).
Place the installation template included in the package on the desired installation surface.
2).
Drill two holes for the plastic anchors and a big hole for the cable lines based on the template paper, and insert the plastic anchors into the drilled holes.
3).
Attach the provided bottom pad to the bottom of the camera body for the prevention of water permeation.
4).
Detach the dome cover from the camera body by loosening the three screws with the provided T20 Torx wrench.
5).
Make the screws (M4x35) ready for the installation: Insert the provided waterproof bracket and the O-ring into the screw in a row by placing the head of the bracket beneath the screw head by reference to the squared image on the left.
6).
Take the camera to the ceiling, and connect the necessary cables including a LAN and power cable (or PoE cable) dropped from the ceiling to the corresponding connectors on the camera.
7).
Align the screw holes on both sides of the camera body and the installation surface, insert the screws prepared at the step 5 into the screw holes on the camera body, and tighten them into the plastic anchors on the ceiling with a screw driver.
8).
Adjust the angle of the camera. Refer to Adjusting Angle of the Camera for more details.
9).
Reattach the dome cover to the camera body by aligning the screws on the dome cover with the alignment holes on the camera body. Refer to the caution below for the alignment method.
10).
Once properly aligned, tighten the screws into the camera body with the provided Torx wrench for the firm attachment of the dome cover. Then, remove the protection film from the dome cover.
Bottom
Pad
Torx Bolt
(M4 x 20)
O-Ring
Waterproof Bracket
Screw
(M4x35)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 24
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.4.2
REATTACHMENT OF DOME COVER
–
ALIGNMENT
The screw hole where the cable line passes has a block next to it due to the cables underneath. Thus, the part shaped differently from the other two screw hole parts shall be aligned with the corresponding part of the dome cover, which is also shaped differently from the other two parts.
Refer to the image on the right for the clarification.
CAUTION: Do not forcefully pull or shake the dome cover as it is linked to the camera body with a safety wire.
CAUTION: To prevent products from damage, install the camera on stable and non-vibrating surfaces. If
Reset Button the stability of a mount surface is in doubt, consult the safety personnel for reinforcements, and then proceed with the installation.
3.4.3
ADJUSTING ANGLE OF THE CAMERA
Adjust the angle of the camera by manually moving the corresponding parts by reference to the directions below.
Gimbal Bracket
Tilt Stopper Screw
Inner Liner
Camera Gimbal
Gimbal Bracket
A. To pan, rotate the gimbal bracket horizontally.
B. To tilt, tilt the camera gimbal by vertically adjusting it.
C. For the horizontal rotation of the lens, rotate the inner liner clockwise or counter-clockwise with the inner liner.
CAUTION: Refrain from continuous rotation of the camera gimbal or the inner liner to a single direction as they are attached to the IR-LED cable inside.
CAUTION: Be careful not to make the ambient light sensor hidden by the dome cover when adjusting the camera angle. The ambient light sensor shall be uncovered for its normal operation.
NOTE: Tighten the tilt stopper screw after the angle adjustment is completed.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 25
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.4.4
CONNECTIONS
Camera
DC Power
❷
Cable
RJ-45
❶
LAN cable
Power Adaptor
1).
LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable
(RJ45 to connect the device to a hub or a router in the network. Refer to Section 6: Power over
Ethernet Specifications for further detail.
Power Connection: The camera can be powered from either 12VDC or PoE. If the camera is powered via
PoE, refer to Section 6: Power over Ethernet Specifications for further detail.
Screw &
Plastic Anchor-3pcs
Bottom Pad
Quick Installation Guide
Installation Template
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC
Adaptor & AC Plug
26
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.5
Full Camera Specifications
Camera Module
CMOS
Image Sensor
Effective Pixels
1/2.9
” 1080p CMOS
1920x1080
Scanning system Progressive scanning
Electrical
Resolution 1920 x 1080
Min. Illumination Color: 0.5 lux, BW: 0 lux (IR LED On)
AGC Control
Lens
Day & Night
Wide Dynamic
Range
Video
Compression
Format
Number of
Streams
Resolution
Auto
4.0mm, F1.8
True Day & Night
Digital WDR
H.264 Baseline, Main, High profile(MPEG-4 Part 10/ AVC),
MJPEG(Motion JPEG)
Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
Compression FPS 30fps@1080p
Motion Detection Built-in
Burnt-in Text
(Digital)
Video stream overlay text
Audio
Input/output
Compression
Format
-
-
Function
Digital
Input/Output
RS-485
-
-
Network 10/100 Base-T
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 27
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Function
Power over
Ethernet (PoE)
Supported
Protocol
SD Slot
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB-
II), IGMP, ICMP, SSLv2/v3, TLSv1
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
Electrical Characteristics
DC 12V / PoE IEEE802.3af (Class 0) Power Source
Power
Consumption
Video Output
Audio Input
Audio Output
D/I
D/O
Max. 5.4 W @ DC 12V
-
-
-
-
-
Environment Condition
Operating
Temperature
Operating
Humidity
-20 ˚C ~ 5 0˚C (
Up to 85% RH
-4 ˚F ~ 1 22 ˚F)
Mechanical Condition
Material Aluminum Die-Casting (Vandal Resistance)
Color
Dimension
Ivory
Housing: 125 (Ø) x 74.5 (H) mm
Dome: 65(Ø) mm
Weight (Approx.) 455g (1lb)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 28
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.6
Camera Dimensions
2.56 in. (65 mm)
4.92 in. (125 mm)
1.35 in. (34.3 mm)
M o unting tem p la te
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 29
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.7
Compatible Accessory Installation (Mounts)
The following are the various combinations of the compatible accessories to mount this camera model.
Model Names & Combinations:
VX-2AD-WM + VX-2AD-PMC
VX-2AD-CM + VX-2AD-PMC
VX-2AD-GB
Refer to the corresponding accessory model ’ s installation guide for the instructions.
Model Image
VX-2AD-WM VX-2AD-CM VX-2AD-PMC VX-2AD-GB
3.7.1
WALL MOUNT- VX-2AD-WM
Contents
C
D
B
A
A - A - A : IP N 3202H D
B - B : IP N 352H D & IP X 5502H D
C - C : IP N 3402H D
D - D - D : IP N 2103H D & IP N 3102H D & IP N 3502H D
B
D
A C
A
D
D
Wall Mount Bracket x 1
Installation
M5 Tapping Screw x 4 Plastic Anchor x 4
Steps:
1).
Cover the wall mount bracket with the waterproof gasket like the image on the left.
C
A
C C
B B
A - A : IP N 352H D & IP X 5502H D
B - B - B : IP N 3202H D
D
Waterproof Gasket x 1
A
B
Wall Mount Bracket
W
NPT 1-1/4 ”
Waterproof Gasket
W
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 30
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Drill the four holes on the installation surface based on the screw holes on the wall mount bracket, and insert the plastic anchors into the holes. Then, insert the tapping screws through the screw holes on the wall mount bracket into the anchor blocks to tighten the bracket into the wall
Attach an Additional Bracket
Attach an additional bracket at the bottom of VX-2AD-WM by referencing to the bracket ’ s installation section, Pendant Mount Cap - VX-2AD-PMC .
Waterproof Gasket
W
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 31
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.7.2
CEILING MOUNT- VX-2AD-CM
Contents
Ceiling Mount Bracket x 1
Installation
M5 Tapping Screw x 4 Plastic Anchor x 4 Waterproof Gasket x 1
Steps:
1).
Cover the ceiling mount bracket with the waterproof gasket like the squared image on the left.
2).
Drill the four holes on the installation surface based on the screw holes on the ceiling mount bracket, and insert the plastic anchors into the holes. Then, insert the tapping screws through the screw holes on the ceiling mount bracket into the anchor blocks to tighten the bracket into the ceiling.
Waterproof
Gasket
Wall Mount
Bracket
NPT 1-1/4 ”
Plastic Anchor
Ceiling Mount
Bracket
Tapping Screw
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 32
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Attach an Additional Bracket
3). Attach an additional pendant bracket at the bottom of VX-2AD-CM by referencing to the bracket ’ s installation section,
Pendant Mount Cap - VX-2AD-PMC.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 33
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.7.3
PENDANT MOUNT CAP - VX-2AD-PMCB
Contents
C
D
B
A
A
D
B
A
D
C
A - A - A : IP N 3202H D
B - B : IP N 352H D & IP X 5502H D
C - C : IP N 3402H D
VX-2AD-PMCB
(M4 x 22 bolt & O-Ring & Waterproof Bracket) x 2
(M4 x 12 bolt & O-Ring) x 4
C
D
B
A
A
D
B
D
A C
A - A - A : IP N 3202H D
B - B : IP N 352H D & IP X 5502H D
C - C : IP N 3402H D
D - D - D : IP N 2103H D & IP N 3102H D & IP N 3502H D
A
B
D
C
D
A C
B
A
D
Installation
Steps:
A - A - A : IP N 3202H D
B - B : IP N 352H D & IP X 5502H D
C - C : IP N 3402H D
D - D - D : IP N 2103H D & IP N 3102H D & IP N 3502H D
1).
Install your camera at the bottom of VX-2AD-PMCB with the corresponding bolts by reference to the screw hole below.
VX-2AD-CM
Screw Holes Guide for Camera
VX-2AD-PMCB
The image below shows the bottom of VX-2AD-CM with the screw holes specific to the VX-2AD3B-IWD camera model (labelled as B ). Refer to the screw hole information below to attach the VX-2AD3B-IWD camera to the VX-2AD-CM mount.
C
D
B
A
B
D
A C
A - A - A : IP N 3202H D
C - C : IP N 3402H D
D - D - D : IP N 2103H D & IP N 3102H D & IP N 3502H D
A
D
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 34
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
3.7.4
GANG BOX MOUNT
–
VX-2AD-GB
Contents
D
C
B
A
B
C
A
B
C
D
A - A : IP N 352H D & IP X 5502H D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
D - D : IP N 3402H D
(M4 x 22 bolt & O-Ring & Waterproof Bracket) x 2
D
C
B
A
D
C
B
B
C
A
A
B
C
D
A - A : IP N 352H D & IP X 5502H D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
D - D : IP N 3402H D
M4 x 20 bolt x 4
VX-2AD-GB
Installation
The images below show how to attach VX-2AD-GB to gang boxes of four different types.
Refer to the screw hole information to attach VX-2AD-GB to your gang box.
Single Gang Box
C
B B
D D
A - A : IP N 352H D & IP X 5502H D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
D - D : IP N 3402H D
A
B
C
B
A
C
D
D
D
A - A : IP N 352H D & IP X 5502H D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
D - D : IP N 3402H D
C
B
A
B
C
C
< VX-2AD-GB attached to a single gang box >
A
C
B
D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
D - D : IP N 3402H D
A
B
C
A
D
A - A : IP N 352H D & IP X 5502H D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
B
C
< VX-2AD-GB attached to a double gang box >
C
< VX-2AD-GB attached to a 3.5
” octo gang box > < VX-2AD-GB attached to a 70mm octo gang box >
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 35
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Screw Holes Guide for Camera
The image below shows the bottom of VX-2AD-GB with the screw holes specific to the VX-2AD3B-IWD camera model (labelled as A ). Refer to the screw hole information below to attach the VX-2AD3B-IWD camera to the VX-2AD-GB mount.
D
C
B
A
B
C
A
B
C
D
B - B - B : IP N 3202H D
C - C - C : IP N 2103H D & IP N 3102H D & IP N 3502H D
D - D : IP N 3402H D
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 36
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4 VX-2A-IMD-X - 2 MP Interior Mini Dome Camera
The VX-2A-IMD-X is a fully functional indoor IP camera with advanced analytics capabilities. These cameras can be connected to a DVR or act as a standalone recording device.
The interior mini dome offers high-definition video at full 1920 x 1080 resolution for indoor video surveillance applications which require superior clarity and detail. Its many features include; dualstreaming of either H.264 or MJPEG compression; Micro SD card slot for local recording; and an unobtrusive dome design.
The embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to configure a detection rule. These advanced analytics allow for object classification, direction, people counting, dwell times, and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a stand-alone device recording video to the onboard memory card. This makes the camera compatible with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud applications. Simple plug and play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.
4.1
VX-2A-IMD-X Specifications - Quick Summary
Component Feature Description
Camera
1/2.7
” 1080p CMOS Image Sensor
Digital Day/Night
WDR
Vandal Proof (IK09)
Video
Network
Integration
General
Video Contents
Analysis (VCA)
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion
JPEG)
Max 30fps in 1080p
Text Overlay
10/100 Base-T Ethernet
ONVIF compliant (Profile S)
Micro SD/SDHC Card Slot x1
Power over Ethernet (PoE)
VCA Presence Standard
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 37
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.2
Package Contents
Please unpack the package carefully and handle the equipment with care.
The package contains:
Camera Screws(M4x20) and anchor blocks
Quick Installation Guide Torx Wrench(T-10)
White Plug Installation Template
NOTE: The contents above are subject to change without prior notice.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 38
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.3
Part Names
❸
❷
❶
* Models herein and their appearance are subject to change without any prior notice.
1).
LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
Reset button: Use the button to restart the device or to reset it to Factory Default. Refer to the 3xLOGIC
VISIX All-in-One Camera User Manual for more details on restarting/resetting to factory default. microSD/SDHC card slot: Supports up to 32GB. Recommend Class 4 and higher for HD recordings.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 39
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.4
Installation
4.4.1
INSTALLING THE CAMERA
–
INSTALLING WITHOUT BRACKET
Installation Template
2 x
.236 in. (6 mm)
CAUTION: Installation template ’ s image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package separately.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 40
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Steps:
1).
Place the installation template included in the package on the desired installation surface.
2).
Drill two holes in the correct positions based on the paper mounting template, insert the plastic anchors into the holes, and tighten them into the holes.
3).
Loosen the two bolts on the dome cover with the provided torx wrench (T-10) to open the dome cover.
4).
Connect necessary cables including a LAN cable and a power cable to the camera.
5).
Place the camera body to match the alignment holes with the provided plastic anchors, and hold the camera against the surface where the camera will be mounted.
6).
Tighten the plastic anchors with the provided screws (M4x20).
7).
Once you can see the video on the camera, adjust the angle of the camera. Refer to
Adjusting Angle of the Camera for more details.
8).
Place the dome cover on the camera's main body to close the dome cover. Dome cover has two alignment holes that match the camera body’s alignment holes.
9).
Once properly placed, tighten the bolts with the provided torx wrench (T-10).
10).
As the last step, insert the white plugs into the screw holes on the dome to keep the dome cover neatly.
CAUTION: To prevent products from damage, place the camera on stable and non-vibrating surfaces If the stability is in doubt, consult safety personnel for reinforcements, and then proceed with the installation.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 41
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.4.2
ADJUSTING ANGLE OF THE CAMERA
Adjust the angle of the camera by manually moving the corresponding parts following the directions below.
A. To tilt, tilt the lens by vertically adjusting the camera gimbal.
4.5
Connections
❷
Connection Status LEDs
B. To pan, rotate the lower body of the camera gimbal.
C. Rotate the lens with upper lens shell
❶
LAN Connection
1).
LAN Connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable
(RJ45. to connect the device to a hub or a router in the network. Refer to Section 7: Power over
Ethernet Specfications for further detail.
Connection Status Indicators: Two LEDs are located near the SD card slot, and you can check the connecting status by observing the LED on the right side.
Solid red – The device is in the process of booting.
Blinking green – Booting is completed
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 42
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.6
Full Camera Specifications
Camera Module
CMOS
Image Sensor 1/2.7
” 1080p CMOS
Effective Pixels 1920x1080
Scanning system Progressive scanning
Electrical
Resolution 1920 x 1080
Min. Illumination Color: 1.0Lux B/W : 0.001 Lux (DSS ON)
AGC Control Auto
Lens 2.0mm, F2.0
Digital Day & Night Day & Night
Wide Dynamic
Range
Digital WDR
Video
Compression
Format
Number of
Streams
H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC),
MJPEG (Motion JPEG)
Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality
Resolution
Burnt-in Text
(Digital)
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
Compression FPS 30fps@1080p
Motion Detection Built-in
Video stream overlay text
Audio
Input/output
Compression
Format
-
-
Function
Digital
Input/Output
RS-485
Network
Power over
Ethernet (PoE)
-
-
10/100 Base-T
Supported
Protocol
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB -
II), IGMP, ICMP, SSLv2/v3, TLSv1
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 43
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Function
SD Slot
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
Electrical Characteristics
Power Source
Power
Consumption
Video Output
Audio Input
D/I
D/O
Audio Output
PoE IEEE802.3af (Class 2)
2.4W @ PoE
-
-
-
-
-
Environment Condition
Operating
Temperature
Operating
Humidity
Operating Range
PoE : 0 ˚C ~ 4 0 ˚C (32˚F ~ 1 04 ˚F)
Up to 85% RH
Mechanical Condition
Material
Color
Aluminum Die-Casting (Vandal Resistance)
Ivory
Dimension
Housing: 105.5 (Ø) x 55.5(H) mm
Dome : 27.5(Ø) mm
Weight (Approx.) 270g (0.6lb)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 44
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.7
Camera Dimensions
R 1.08 in.
(27.5 mm)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 45
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.8
Compatible Accessory Installation (Mounts)
The compatible accessories to mount this camera model are as follows.
Model Names & Combinations
VX-2AIMD-CM
VX-2AIMD-WM
VX-2AIMD-CM + VX-2AIMD-PMC
VX-2AIMD-GB
The installation instructions for each bracket are contained within the proceeding sections of this manual.
Model Image
VX-2AIMD-CM VX-2AIMD-CM
VX-2AIMD-PMC VX-2AIDM-GB
4.8.1
WALL MOUNT - VX-2AIMD-WM
W M B - 3202/C M B - 3202
W M B - 3202/C M B - 3202 p o le m o unt adapter.
Contents
C heck the letter o f the alp hab et assigned to each adapter and tighten the screw s in the co rresp o nd ing ho les to assem ble the adapter.
A
B
A
W M B - 3202/C M B - 3202
This g uid e illustrates ho w to assem b le the corner m ount adapter and
A p o le m o unt adapter.
W M B - 3202/C M B - 3202
This guid e illustrates ho w to assem ble the co rner m ount adapter and p ole m o unt ad ap ter.
C heck the letter of the alp habet assigned to each adapter and tighten the screw s in the corresp onding holes to assem b le the adapter.
A
B
A - A - A (M 3TA P )
A
B - B (M 3TA P )
IP N 302H D
A
B
A
B
A
B
A
A - A - A (M 3TA P )
M O D E L : IP N 3202H D
B - B (M 3TA P )
M O D E L : IP N 302H D
B
A - A - A (M 3TA P )
M O D E L : IP N 3202H D
B - B (M 3TA P )
M O D E L : IP N 302H D
A
A - A - A (M 3TA P )
M O D E L : IP N 3202H D
B - B (M 3TA P )
M O D E L : IP N 302H D
Wall Mount Bracket
Plastic Anchor 3ea
M3x6L BOLT 4ea
A
B
Tapping Screw 3ea
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 46
W M B - 3202/C M B - 3202
This guid e illustrates ho w to assem ble the co rner m ount adapter and p ole m o unt ad ap ter.
C heck the letter of the alp habet assigned to each adapter and tighten the screw s in the corresp onding holes to assem b le the adapter.
A - A - A (M 3TA P )
IP N 3202H D
B - B (M 3TA P )
IP N 302H D
A
B
A
A
B
W M B - 3202/C M B - 3202
This guid e illustrates ho w to assem ble the co rner m ount adapter and p ole m o unt ad ap ter.
C heck the letter of the alp habet assigned to each adapter and tighten the screw s in the corresp onding holes to assem b le the adapter.
A - A - A (M 3TA P )
IP N 3202H D
B - B (M 3TA P )
IP N 302H D
A
B
A
A
B
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Installation
Steps:
1).
Drill three small holes for plastic anchor and one hole for cabling work on the ceiling based on the holes of the bracket. Refer to Location of the Holes for M3x6L Bolts on the next page to identify the holes information.
2).
Insert the plastic anchors (3ea) to the drilled three holes.
3).
Fix the bracket on the wall by tightening the tapping screws (3ea) into the plastic anchors.
4).
Detach the dome cover from the camera by loosening the bolts with the hex wrench included in the camera package.
5).
Fix the camera at the bottom of the bracket with the M3x6L bolts. Ensure that the necessary cables are properly connected to the camera.
6).
For the last parts of the installation, refer to the steps 7 to 10 in Section 4.4: Installing the
Camera - Installation without Bracket of this manual.
Tapping Screw
Plastic Anchor
Wall Mounting Bracket
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 47
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
The image below shows which spots the camera should be attached to on the wall mount bracket (VX-
2AIMD-CM).
p ole m o unt ad ap ter.
M3x6L bolts in the holes to attach the camera.
the screw s in the corresp onding holes to assem b le the adapter.
A - A - A (M 3TA P )
IP N 3202H D
B - B (M 3TA P )
IP N 302H D
A
B
A
A
B
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 48
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.8.3
CEILING MOUNT - VX-2AD-CM
Contents
Plastic Anchor 3ea Tapping Screw 3ea
Ceiling Mount Bracket Installation Template 1ea
Installation
Steps:
1).
Drill three holes for the plastic anchors based on the installation template as well as the hole for the cable dropped from the ceiling. Then, route the LAN cable through the bracket ’ s pipe.
Ceiling Mount Bracket
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 49
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
2).
Insert the three anchor blocks into the holes on the ceiling.
3).
Fix the bracket to the ceiling by inserting the tapping screws into the anchor blocks and tightening them for the firm attachment.
4).
This ceiling mount bracket normally requires a pendant mount cap to attach the camera. Refer to the installation method in
Pendant Mount Cap
on the next page.
Plastic Anchor
Tapping Screw
Ceiling Mount Bracket
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 50
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4.8.4
PENDANT MOUNT CAP - VX-2AD-PMC
Contents
Pendant Mount Cap
M5x6L Hex Socket Set Screw 1EA
(pre-installed)
3ea
2.5mm Hex Wrench 1EA
M4x8L Hex Wrench Bolt 2EA
Installation
Ceiling Mount Bracket
(Model No: VX-2AD-PMC)
Set Screw
Hex Wrench
Pendant Mount Cap
Steps:
1).
Rotate the pendant mount cap counterclockwise on the thread at the bottom of the ceiling mount bracket, and tighten the set screw (installed on the pendant mount cap) with the hex wrench included in the bracket package for the firm attachment of the pendant mount cap.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 51
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Biscuit Camera
M4x8L Hex Wrench Bolt
Hex Wrench
5).
Connect your LAN (or PoE) cable from the ceiling pipe to the LAN connector on the camera, and insert the camera into the pendant mount cap. Then, fix the camera to the pendant mount cap by inserting the bolts (M4x8L) to the alignment holes on the pendant mount cap and tightening them with the hex wrench included in the camera package.
6).
For the last part of the installation, refer to steps 7 to 10 in Section 4.4:
Installing the Camera
– Installation without Bracket
in this manual.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 52
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5 VX-VT-20, VX-VT-36, VX-VT-58 – VERA 20°, 36°,
58° Thermal Bullet Camera
The VERA indoor/outdoor thermal bullet gives you the advantage to see where you couldn’t before.
When using high-contrast thermal imaging the results are a dramatic reduction in false alarms. Our thermal camera stands out from the pack with verification and detection in an all-in-one device. Easy setup and integration using our QR code makes this a perfect camera for any application.
The exterior thermal camera is not affected by changes in lighting, low contrast scenes or inclement weather. There is no illumination required.
The VERA Thermal line includes three models with a 20, 36 or 58 degree field of vision. The VERA camera’s embedded analytics use algorithms that automatically self-adjust, allowing the user to concentrate on the detection rules. This greatly simplifies the analytic process, requiring only a few mouse clicks to configure a detection rule. These advanced analytics, coupled with thermal technology allow for object classification, direction, people counting, dwell times, video alarm verification, retail traffic flow, queue management and occupancy counts.
When enabled, the embedded VIGIL Server software from 3xLOGIC allows the camera to be run as a stand-alone device recording video to the onboard memory card. This makes the camera compatible with the 3xLOGIC software suite including VIGIL Client, VIGIL VCM, VIGIL Mobile and VIGIL Cloud applications. Simple plug-and-play installation allows for access using a standard web browser, VIGIL
Client, or your mobile device or tablet using our easy to use QR code quick setup.
5.1
VX-VT-20, VX-VT-36, VX-VT-58 Specifications
–
Quick
Summary
Component Feature Description
17 ㎛ vanadium oxide microbolometer technology
Camera
206x156 array size / various resolutions via scale-up
20, 36 or 50 degree field-of-view (depending on model)
Streaming
Video
Audio
Dual streaming supported
Burnt-in text (OSD) supported
Unicast/Multicast supported
H.264 and MJPEG(Motion JPEG)
Max 9fps in all resolutions
Text Overlay
Video Motion Detection Supported
Two-way audio streaming
Audio compression: G.711 µLaw
Sensor/Alarm 1 Digital Input / 2 Digital Outputs
Network
RTSP/HTTP Protocols supported
10/100 Base-T Ethernet
Integration ONVIF compliant (Profile S)
General
Video Contents
Analysis (VCA)
Micro SD/SDHC Card Embedded
Power over Ethernet (PoE)
VCA Presence Standard
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 53
Torx Wrench
Screw &
Plastic Anchor-3pcs
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5.2
Package Contents
Please unpack the package carefully and handle the equipment with care. The package contains:
Camera
WALL CUSHION
Quick Installation Guide
DC Power Adaptor & Universal Plugs Installation Template
Torx Wrench
WALL CUSHION
Adaptor & AC Plug
Screws (M4x30) & Plastic Anchors Wall Cushion
Torx Wrench
CABEL CORE
Screw &
Plastic Anchor-3pcs
Screw &
Plastic Anchor-3pcs
Torx Wrench
WALL CUSHION
Quick Start Guide
Plastic Anchor-3pcs
WALL CUSHION
Installation Template
Quick Installation Guide
Installation Template
CABEL CORE
Torx Wrench
Ferrite Core
Quick Installation Guide
Installation Template
WALL CUSHION
Z C A T1518- 0730 Z C A T2132- 1130
NOTE: The contents above are subject to change without prior notice.
Adaptor & AC Plug
Adaptor & AC Plug
CABEL CORE
CABEL CORE WALL CUSHION Quick Installation Guide
Installation Template
Adaptor & AC Plug
CABEL CORE
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 54
Torx Wrench
WALL CUSHION
Adaptor & AC Plug
Screw &
Plastic Anchor-3pcs
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Quick Installation Guide
CABEL CORE
Installation Template
5.3
Part Names
❶
Sunshield
BLACK
BROWN
RED
ORANGE
YELLOW
GREEN
BLUE
VIOLET
GRAY
AUD IN
AUD GND
AUD OUT
DI
DI COM
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM
❸
❹
Power adaptor
connector
LAN connector
❷
Audio|Sensor|Alarm connection cables
1).
Sunshield: It prevents direct sunlight.
2).
Audio|Sensor|Alarm connection cables: Cables to connect audio input(microphone), audio output(speaker), digital input(sensor), and digital output(alarm). Refer to Section 5.5: Connections for more information.
3).
LAN connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported).
4).
Power adaptor connector: Connect the provided DC12V adaptor for power supply.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 55
Torx Wrench
Screw &
Plastic Anchor-3pcs
WALL CUSHION Quick Installation Guide
Installation Template
Adaptor & AC Plug
CABEL CORE
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5.4
Installation
5.4.1
INSTALLING THE CAMERA
–
INSTALLATION WITHOUT BRACKET
Installation Template
Ø2.72 in. (69 mm)
3 - Ø0.26 in. (6.5 mm)
CAUTION: Installation template ’ s image size scale in this installation guide is not 1:1. The correct-size template paper can be found inside the package separately.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 56
Torx Wrench
WALL CUSHION
Adaptor & AC Plug
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Quick Installation Guide
CABEL CORE
Screw &
Plastic Anchor-3pcs
Steps:
1).
Drill three holes on the installation surface based on the provided installation template.
2).
Insert the plastic anchors into the holes.
3).
Install the provided ferrite core on the cable by referring to the NOTE: below.
4).
Attach the provided wall cushion to the bottom of the camera ’ s pan/tilt bracket.
5).
Fix the camera to the installation surface. a.
Align the screw holes of the camera ’ s pan/tilt bracket and the plastic anchors. b.
Insert the provided screws(M4X35) into the plastic anchors through the screw holes of the camera ’ s pan/tilt bracket. c.
Tighten the screws firmly into the plastic anchors.
6).
Connect all the necessary cables by referring to Section 5.5: Connections for more information.
7).
Adjust the angle by referring to
Adjust Angle of the Camera
.
NOTE: Installing the ferrite core to a LAN cable is highly recommended to reduce high frequency noise level. Please follow the instructions below:
Steps:
1).
Open the ferrite core by lifting the clip.
2).
Make one loop with the cable through the ferrite core.
3).
Close the ferrite core to hold the cable loop into its place.
ETHERNET
WIRE
CAUTION: Sealing gaps is recommended as gaps may appear after the camera installation. Gaps may cause problems such as moisture, water leakage and etc., which negatively affect the operation of the camera if gaps remain unsealed.
CAUTION: To prevent products from damage, place the camera on a stable and non-vibrating surface. If the stability is in doubt, consult safety personnel for reinforcements, and then proceed with the installation.
RESET
MICRO
SD DO
C 1 C
DI
1
DC12V
ETHERNET
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 57
C
DO
1 C
DI
1
DC12V
ETHERNET
RESET
MICRO
SD
Torx Wrench
Screw &
Plastic Anchor-3pcs
WALL CUSHION Quick Installation Guide
Installation Template
Adaptor & AC Plug
CABEL CORE
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5.4.2
ADJUSTING ANGLE OF THE CAMERA
❶
❷
Steps:
1).
Loosen the set screw located on the right side of the camera ’ s bracket by using the provided
Torx (T20 M4x23) wrench. Once the set screw is loosened, you can move the tilting joint and the panning joint of the camera respectively.
2).
Adjust the angle by moving the tilting joint and the panning joint.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 58
Torx Wrench
WALL CUSHION
Adaptor & AC Plug
Reset
Quick Installation Guide
CABEL CORE
Screw &
Plastic Anchor-3pcs
S
W
1
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
S
W
2
Installation Template
5
S
W
S
W
6
S
W
4
S
W
3
5.5
Connections
❶ AUDIO
BLACK
BROWN
RED
AUD IN
AUD GND
AUD OUT
❷ SENSOR
ORANGE
YELLOW
DI
DI COM
❺ Power adaptor
❹ LAN connector
❸
ALARM 1
ALARM 2
GREEN
BLUE
VILOET
GRAY
DO1(N.O)
DO1 COM
DO2(N.C)
DO2 COM
SW1 SW2
N / A
SW3
N / A
1).
Audio connection: The camera provides a mono audio input and output. Due to low audio output
SW5 SW6
Microphone In: Max 2Vp-p, 20K
Ω
(90dB)
Headphone Out: 60mW, 16
Ω
(95dB)
VIDEO
Out
DO DI
C 1 C
Amp Speaker
1
AUDIO
Out In ETHERNET MICRO SD
Mic
2).
Sensor (DI) connection : Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor as the following figures. Settings can be done through the camera ’ s webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
CAUTION: Do not exceed the maximum input voltage or relay rate.
DC12V
+
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 59
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Internal +3.3V
DI
Output of
Sensor
+ -
Internal
DI
COM
Relay Type
3).
Alarm (DO1 | DO2) connection: Only the relay type is supported.
COM
Voltage Type
Output of
Sensor
+ -
- +
Digital Output 1
Relay Rating: Max 30VDC 1A
Normally Open (N.O) at power off
Digital Output 2
Relay Rating: Max 30VDC 1A
Normally Closed (N.C) at power off
CAUTION: Do not exceed the maximum relay rating.
4).
LAN connection: This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable
(RJ45) to connect the device to a hub or a router in the network. Refer to Section 7: Power over
Ethernet Specifications for more information.
5).
Power Connection: The camera can be powered by either 12VDC or PoE. If the camera is powered via PoE, you do not need to connect the power adaptor. For more information about PoE, refer to
Section 7: Power over Ethernet Specifications for more information.
NOTES:
Temperature criterion for the heater operation: 0 ˚C ( 32 ˚F)
Lowest temperature to guarantee the heater operation during the device operation: -40 ˚C ( -40 ˚F)
Lowest temperature to boot up the device when the device is powered on:
0 ˚C ( 32 ˚F)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 60
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5.6
Full Camera Specifications
Camera Module
Array Size
Detection Type
Sensor pixel size
Spectral Response
Lens
Sensitivity
Video
Compression Format
Number of Streams
Resolution
4:3 Mode
16:9 Mode
Frame Rate
Motion Detection
Burnt-in Text (Digital)
Analogue Output
Audio
Input/output
Compression Format
Function
Digital Input/output
RS-485
Network
Power over Ethernet
(PoE)
206x156
Uncooled vanadium oxide microbolometer
12um
7.8 ~ 14
4mm, F1.2 (FOV:36 o ), 6.8mm F1.2(FOV:20 o ), N/A FOV:58 o ),
Less than 100mK
H.264 and MJPEG Selectable per Stream
Dual Stream, Configurable
QVGA(320x240), VGA(640x480), NTSC(720x480), PAL(720x576), SVGA(800x600)
320x180, 480x270, 640x360, 800x450, 960x540, 1120x630, 1280x720
Max. 9FPS in all resolutions
Built-in
Time stamp and text caption overlay
-
1/1 channel
G.711
1/2 channel
-
10/100 Base-T
Supported
Protocol
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv2c/v3(MIB -II),
IGMP, ICMP, SSLv2/v3, TLSv1, SRTP, RTMP
Storage 1 x microSDHC card embedded
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 61
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
5.7
Camera Dimensions
2.40 in. (61 mm)
8.17 in. (207.5 mm)
2.28 in.
(58 mm)
2.72 in.
(69 mm)
7.5 in. (190.5 mm)
6.75 in. (171.5 mm)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 62
Torx Wrench
Screw &
Plastic Anchor-3pcs
WALL CUSHION Quick Installation Guide
Installation Template
Adaptor & AC Plug
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6 VX-2V28-PIN – IP Pinhole Camera
6.1
VX-2V28-PIN Specifications
—
Quick Summary
Component Feature Description
Camera
1/3 ” 1080p CMOS Image Sensor
Digital Day/Night
WDR
Video
H.264 Baseline, Main, High profile (MPEG-4 Part 10/AVC), MJPEG (Motion
JPEG)
Max 30fps in 1080p
Text Overlay
Network 10/100 Base-T Ethernet
Integration
Software Development Kit (SDK) available
ONVIF Compliant (Profile S & Profile G)
NOTE: ONVIF Profile G is supported from FW V1.8.0 or higher.
General
Micro SD/SDHC Card Embedded
Power over Ethernet (PoE)
Video Contents
Analysis (VCA)
VCA Presence Standard
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 63
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.2
Package Contents
Please unpack the package carefully and handle the equipment with care. The package contains:
Camera Unit Main Unit Universal Plugs Power Adaptor (DC12V)
Double-Sided Tape for
Pinhole Cover
Pinhole Cover Rotate Ring Surface Mount Bracket
Pan/Tilt Bracket Tapping Screw
(TP1 M3x20) x 2EA
Screw
(TP2 M3x6(Ni)) x
2EA
Anchor Block
(M4x25) x 5EA)
Tapping Screw
TS1 (M4x25) x 5EA
Cable Clamp x 3EA Ferrite Core Tapping Screw
(TP1 M4x20) x 3EA
4 Pin Terminal Block
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 64
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.3
Part Names
6.3.1
MAIN UNIT:
❹
❺
❻
❼
❶
❷
❸
* Model herein and its appearance are subject to change without any prior notice.
1).
Terminal Connector: Connector for cable connection for digital input / output. Refer to Section 6.5:
Cable Connection for more details.
2).
Camera Connector: Connector for camera unit
3).
microSD/SDHC card slot: The camera supports up to 32GB. Class 4 and higher SD card is recommended for HD recordings.
4).
Reset button: This button will restart or reset to factory default settings.
5).
LAN Connector: RJ45 LAN connector for 10/100 Base-T Ethernet (PoE supported)
6).
Power Adaptor Connector: DC 12V power supply connection
7).
Slide Plate: Built-in mounting bracket for main unit
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 65
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.3.2
CAMERA UNIT WITH CONJOINED ACCESSORIES
❶
❸
❹
❺
❷
* Model herein and its appearance are subject to change without any prior notice.
1).
Camera
2).
Camera DIN connector: Connector to be inserted to the camera connector in the main unit
3).
Pinhole Cover : Bracket to be installed behind a wall or ceiling to hold the camera inside
4).
Surface Mount Bracket: Bracket to be installed on a wall or ceiling to hold the camera inside
5).
Pan/Tilt Bracket: Bracket to be installed on a wall or ceiling for the camera ’ s angle adjustment. It shall be combined with the rotate ring and the surface mount bracket for the complete installation.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 66
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.4
Installation
6.4.1
CAMERA UNIT INSTALLATION
There are three different ways to install the camera unit:
Inconspicuously behind the wall or ceiling by using the pinhole cover
Mounted and fixed on the wall or ceiling by using the surface mount bracket
Mounted and fixed on the wall or ceiling by using the pan/tilt bracket to enable the camera ’ s angle adjustment
6.4.2
INCONSPICUOUS INSTALLATION
Steps:
1).
Drill a hole (diameter: 3mm) on a desired spot where the camera lens will be located.
2).
Peel off one side of the double-sided tape, and attach it to the flat surface of the pinhole cover by aligning the grooves on the tape with the screw holes on the pinhole cover. tape groove
(Behind the wall or above the ceiling)
Screw hole
3).
Peel off the other side of the tape, and stick the taped surface to the installation surface after aligning the hole on the pinhole cover with the drilled hole on the installation surface and facing the top screw hole upward.
4).
Fasten the pinhole cover by using the tapping screws (M3x20) appropriate for the material of the installation surface.
5).
Place the camera inside the pinhole cover by routing the camera ’ s cable through the cable holder on the pinhole cover, and tighten the top screw head to fix the camera.
(Behind the wall or above the ceiling)
Screw head cable holder cable holder
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 67
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6).
Use the cable clamp optionally if you want to fix the camera ’ s cable to a desired spot with a tapping screw
(M4x20).
(Behind the wall or above the ceiling) cable clamp
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 68
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.4.4
SURFACE INSTALLATION FOR FIXED
ANGLE
Steps:
1).
Place the camera on a desired installation surface.
2).
Cover the camera with the surface mount bracket by routing the camera ’ s cable into the cable holder on the bracket. Then, fasten the bracket using the tapping screws (M3x20) and anchor blocks appropriate for the material of the installation surface.
3).
Use the cable clamp optionally if you want to fix the camera ’ s cable to a desired spot with a tapping screw (M4x20). cable clamp
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 69
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.4.5
SURFACE INSTALLATION FOR PAN/TILIT
ADJUSTMENT
Steps:
1).
Drill a hole on a desired installation surface, and insert an anchor block into the hole.
2).
Fix the pan/tilt bracket by inserting the tapping screw
(M4x25) to be passed through the screw hole on the bracket and tightening it into the anchor block.
3).
Insert the rotate ring into the bracket by pressing it into the bracket ’ s mount ring
4).
Place the camera unit on the pan/tilt bracket.
5).
Place the surface mount bracket on top of the camera, fix the bracket by inserting the tapping screws (M3x6) into the screw holes on the bracket by aligning the screw holes with the holes on the rotate ring on the pan/tilt bracket, and tighten the screws
6).
Use the cable clamp optionally if you want to fix the camera ’ s cable to a desired spot with a tapping screw
(M4x20). rotate ring mount ring cable clamp
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 70
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.4.6
MAIN UNIT INSTALLATION
The main unit can be mounted on the installation surface by the built-in slide plates.
Steps:
1).
Pull out both slide plates at the bottom of the main unit.
2).
Place the main unit on the installation surface by facing the bottom of the main unit toward the installation surface, and mark the drilling spots based on the alignment holes on the slide plates.
3).
Drill the marked spots with a screw driver.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 71
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
4).
Insert the anchor blocks to the drilled holes, and tighten them into the installation surface.
5).
Place the main unit in the same way as in Step 2 and insert the tapping screws to be passed through the alignment holes on the main unit.
6).
Tighten the screws into the anchor blocks to fix the main unit to the installation surface.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 72
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.5
Cable Connection
C
❶
DO DI
1 C DO
❸
❹
❷
6.5.1
DI/DO TERMINAL CONNECTOR
1).
Connect external input/output devices (e.g. alarm device) optionally if they are necessary. Refer to the reference below for the appropriate connection.
DO (Alarm): It is used for connecting an external device such as relays and LEDs.
Refer to the table below for electrical wiring information:
DO
C
1
Function
Ground
Output
Specifications
0 to 24 VDC
Max load: 50mA
Internal
Device
DO
COM
Relay Type
Then, the connected device can be activated via its webpage.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 73
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
DI Sensor: It is used for connecting a device such as a PIR and a door/window sensor.
Refer to the table below for electrical wiring information:
DO
C
1
Function
Ground
Input
Specifications
0 to 5 VDC
Max load: 50mA
Internal +3.3V
DI
Output of
Sensor
+ -
Internal
DI
Output of
Sensor
+ -
COM
Relay Type
Then, the connected device can be activated via its webpage.
C
D
O
1
❶
C
DI
D
1
Voltage Type
COM - +
❸
❹
❷
6.5.2
CAMERA CONNECTOR
2).
Connect the camera unit to the main unit by inserting the camera ’ s DIN connector to the camera ’ s connector on the main unit by placing the arrow mark to be shown upward like the image below.
❷
NOTE: Please make sure that the camera unit needs to be connected to the main unit prior to the power connection. Otherwise, the camera may fail to show image.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 74
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.5.3
LAN CONNECTOR
❸
3).
Connect the main unit to the network using an Ethernet cable (RJ45). Then, install the ferrite core on the Ethernet cable. Refer to the explanations below for the ferrite core installation.
NOTE: In case you intend to turn on the device by using the LAN cable, a PoE switch should be available in your network. For more information about PoE, refer to Section 7: Power over Ethernet
Specifications for more information.
NOTE: Installing the provided ferrite core is highly recommended to reduce high frequency electrical noise level. Here below are the instructions to install the ferrite core on the Ethernet cable.
Steps:
1).
Open the ferrite core by lifting the clip.
2).
Make one loop with the cable through the ferrite core. (See the enlarged image above.)
Close the ferrite core to hold the cable loop in the ferrite core ’ s chamber.
6.5.4
POWER CONNECTOR
4).
Connect a DC12V power adaptor to the power connector on the main unit. If the camera is powered on via PoE, a power adaptor is not necessary to be connected to the main unit.
NOTE: Please make sure that the camera unit needs to be connected to the main unit prior to the power connection. Otherwise, the camera may fail to show image.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 75
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.6
Camera Dimensions
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 76
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
6.7
Full Camera Specifications
Camera Module
CMOS
Image Sensor
Effective Pixels
1/3 ” 1080p CMOS
1920x1080
Scanning system Progressive scanning
Electrical
Resolution 1920 x 1080
Min. Illumination Color: 1.4 Lux / B/W : 0.01 Lux (DSS ON)
AGC Control Auto
Lens 2.8mm, F2.4
Day & Night
Wide Dynamic
Range
Digital Day & Night
Digital WDR
Video
Compression
Format
H.264 Baseline, Main, High profile (MPEG-4 Part 10/ AVC), MJPEG (Motion JPEG)
Number of
Streams
Resolution
Dual Stream, Configurable streams in H.264, MJPEG
H.264: Controllable frame rate, bandwidth(VBR/CBR)
MJPEG: Controllable frame rate, JPEG quality
1920x1080, 1280x720, 1120x630, 960x540, 800x450, 640x360, 480x270,
320x180
Compression FPS 30fps@1080p
Motion Detection Built-in
Burnt-in Text
(Digital)
Video stream overlay text
Audio
Input/output
Compression
Format
Function
Digital
Input/Output
-
-
1/1 channel
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 77
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
Function
RS-485
Network
Power over
Ethernet (PoE)
-
10/100 Base-T
Supported
Protocol
SD Slot
QoS Layer 3 DiffServ, TCP/IP, UDP/IP, HTTP, HTTPS, FTP, RTSP, RTCP, RTP/UDP,
RTP/TCP, mDNS, UPnP™, SMTP, DHCP, DNS, DynDNS, NTP, SNMPv1/v2c/v3(MIB-
II), IGMP, ICMP, SSLv2/v3, TLSv1, SRTP, RTMP
1 x microSD memory card slot
(SD/SDHC up to 32 GB supported)
※ Card not included
(Class 4 and higher recommended for HD recordings)
Electrical Characteristics
Power Source
Power
Consumption
Video Output
DC 12V (Class 2, LPS) / PoE IEEE802.3af (Class 0)
6W @ DC12V
-
Audio Input -
Audio Output -
D/I
D/O
Max 50mA@5VDC, TTL level 1.5V threshold
Max 50mA@24VDC
On-state resistance:50 Ω (max continuous)
Environment Condition
Operating
Temperature
Operating
Humidity
Operating Range
[DC12V] [PoE]: -10 ˚C ~ 50 ˚C ( 14 ˚F ~ 1 22 ˚F)
Up to 85% RH
Mechanical Condition
Material
Color
Dimension
Weight (Approx.)
Polycarbonate
Main Unit: White
Camera Unit: Black
28.1(Ø) x 25 mm
Main Unit: 225g (0.50lbs)
Camera Unit: 250g (0.55lbs)
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 78
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
7 Power over Ethernet Specifications
The Power over Ethernet (PoE) is designed to extract power from a conventional twisted pair Category 5
Ethernet cable, conforming to the IEEE 802.3af Power-over-Ethernet (PoE) standard.
IEEE 802.3af allows for two power options for Category 5 cables.
The IEEE 802.3af-2003 standard allows up to 15.4 W of power the device. However, 12.95W is the available power, as some power gets lost in the cable. The updated IEEE 802.3at-2009 (PoE+) standard allows up to 25.5 W (Max 34.2 W) of power the device.
PoE has advantages over conventional power in such places where AC powers cannot be reached or is expensive to wire.
7.1
Power Comparison
Property 802.3af 802.3at
Available Power
Max. Power by PSE
12.95 W
15.40 W
25.50 W
34.20 W
Max. Current 350 mA 600 mA
Supported Cable Category 3 or higher Category 5 or higher
NOTE: For proper activation of PoE, the Category 5 cable must be shorter than 100m and conform the
PoE standard.
NOTE: When it is connected with non PSE, the power adaptor should be connected.
NOTE: Connecting both PSE and power adaptor does not do any harm to the product. Disconnecting PSE or power adaptor from device does not reboot the device as long as either one is connected to the device.
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 79
Hardware and Installation Manual | VISIX V-Series All-in-One Cameras – Gen I
8 Revision History
Man # Date (mm/dd/yyyy) Comments
11-2015-1
01-2016-22
11-2017-10
06-2018-20
07-2018-31
11/19/2015
01/22/2016
11/10/2017
06/20/2018
07/31/2018
Styled
Finalized first draft
Revised for VIGIL v10
-Added VX-VT-58, VX-2A-B-RIWD
Added VX-2A-B-RIWDZ
Added VX-2AD3B-IWD
12000 Pecos Street, Suite 290, Westminster, CO 80234 | www.3xlogic.com | (877) 3XLOGIC 80

Public link updated
The public link to your chat has been updated.
Advertisement