Select the screen resolution from the drop-down menu based on your TV/monitor’s resolution.
Resolution
System Resolution: 1024 * 768/60HZ
Check this box if you wish to see this wizard again after you reboot your system.
Wizard
Start wizard when device starts?
We strongly recommend that you change the default
Admin password ‘12345’ for better security protection.
Wizard
Admin Password
New Admin Password
New Password
*****
Select the applicable time zone, date/time format, and time.
Wizard
Time Zone
Date Format
System Format
System Time
(GMT-08:00)
MM-DD-YYYY
09-29-2014
18:14:37
We recommend checking ‘Enable DHCP’ even if your DVR is not connected to the internet, this will automatically get the DVR
IP address.
Wizard
NIC Type
Enable DHCP
IPv4 Address
10M/100M Self-adaptive
192.0.0.64
The wizard will show additional network information, click ‘Next’ to proceed.
Wizard
Server Port 8000
HTTP Port 80
RTSP Port 8554
To initialize the hard drive click the ‘Init’ box otherwise the
DVR will NOT record.
Wizard
Capacity Status Property Type
1 R/W Local
Free Space
464GB
If you wish to add an IP camera click ‘Search’ otherwise, click ‘Next’ to proceed.
Wizard
IP Address Amount Model
1 192.168.1.36
1 LV-PC902
Choose continuous or motion detection recording from the listed options. Check the ‘Start Recording’ box to initialize recording. the wizard.
Wizard
Start Recording
Continuous
Motion Detetction
1 DVRPowerAdapter
What is in the box?
NVRPowerAdapter Netowrk Video Recorder
HD Wireless IP Cameras(optional)
Pre-made Cat5e Cables
Pre-made Cat5e Cables
Mouse
Quick Start Guide
Warranty Card
Security S ckers
1 1
2
5
6
3
4
1 Power LED Indicates if the NVR is powered on
2 LAN Connect cameras or a network switch
3 WAN
4 USB Port
5 HDMI Port
Connects to your modem or ISP
Connects to HDTV or monitor
6 AC Power Connects to the Power Supply
Troubleshooting
Problem
NVR does not detect the wireless camera
No display/
No signal/
Invalid format
No picture/
No video
Cannot log in
Camera picture is not clear
Night vision is not working
NVR is not recording
2.
3.
•
1.
4.
•
1.
2.
3.
•
1.
2.
3.
Solution
Method 1. Reset the Camera:
Unplug all the cables from the camera
Press and hold the RESET button on the back of the camera
Continue holding down RESET button while connecting the power adapter
to the camera. Hold for 15 seconds, then release the RESET button.
Wait for the IP camera to show up in the NVR
Method 2. Manually add wireless camera
Reset the camera (Follow Method 1)
Connect a Camera to a yellow LAN port on the NVR using the provided Cat5e cable. The camera will show up in the NVR in 2 -3 minutes.
Remove the cat5e cable and the wireless connection will be established automatically in 30 seconds.
Method 3. Configure using Mobile Device:
Reset the camera
Download and install the Laview Net App from the App store on your mobile device.
Click Menu=> Device => => Wifi Configuration and follow the given instruction to complete the setup process
• Make sure the HDMI cable is properly connected to both the NVR and
TV/monitor
NOTE: A laptop cannot be used as a screen
•
•
•
•
Make sure your TV/monitor is on the correct video input (e.g. HDMI1,
HDMI2,etc.)
Try switching to another 1080p TV/monitor and adjust the output resolution in the NVR menu
Check that the power LED light is on
Make sure the camera is properly connected to the LAN port on the NVR or network switch.
Make sure the camera is connected to a 12VDC power supply
If you do not remember your old password, please submit a ticket to us at www.laviewusa.com/contact
•
•
•
Make sure the camera is not placed behind a window or there is no interference or a strong light source in front of the camera
• In NVR menu > Record > Parameter > Resolution, set the sub stream resolution to CIF for all channels
• Move the camera to a different location and/or direction
NOTE: The live view(Sub stream) resolution is NOT the actual image quality recorded(Main stream); Connection of excessive length (over 300ft) of cat5e cable will drop the camera image quality; Working at extreme weather condition (Below -22F or above 140F) will drop the image quality and damage the camera
•
•
The infrared activates automatically when the environment is dark enough.
You can check that the camera infrared bulbs are working properly as they turn light red in dark environments
Check that the hard drive status is normal and is initialized under the Main
Menu > HDD > General
Wireless IP NVR System
QUICK START GUIDE
Remote Viewing
View footage on your mobile devices with our app. You can either scan the provided QR code below or search Laview Net in the app store. Then scan the QR code located on the NVR for device P2P info
LaView NET SCAN ME and hard drive capacity.
Questions?
Call us at: 626-898-4988
Open suppo
(M-F from 9am - 6pm PST) rt ticket： www.laviewusa.com/contact
Complete user manual can be viewed via included CD disc or can be downloaded at: www.laviewusa.com/support.
www.laviewusa.com
We recommend testing all the cameras and cables prior to installation.
Step 1.
Set up the NVR
a. USB mouse
Connect
c. Power adapter
to the NVR and follow the startup wizard on screen.
a.
HDTV
1080p b.
LAN 1
LAN 2
LAN 3
WAN
HDMI
POWER c.
QUICK START GUIDE
Step 2.
Connect the Camera
LaView wireless cameras will pair with the wireless
NVR automatically when the cameras and the NVR are both powered up. It may take 2 - 5 minutes for the NVR to detect the wireless cameras automatically.
Step 3.
Connect to Network
Connect the NVR WAN port to a Modem or a router via an Ethernet cable to enable the remote viewing and adding remote cameras.
NOTE: The NVR will still work as a standalone video recorder / router, if you do not have internet connection you can skip this step.
(Optional)
Camera configuration menu is located at: NVR main menu => Camera => Camera
See troubleshooting section if the NVR does not detect the cameras automatically.
Optional:
You can also add wireless and standard IP cameras by connecting an Ethernet cable from the cameras to NVR LAN port. It may take
2-3 minutes for the NVR to detect the cameras.
