Exterior/Interior trim
2004 LEGACY SERVICE MANUAL
QUICK REFERENCE INDEX
BODY SECTION
This service manual has been prepared
to provide SUBARU service personnel
with the necessary information and data
for the correct maintenance and repair
of SUBARU vehicles.
This manual includes the procedures
for maintenance, disassembling, reassembling, inspection and adjustment of
components and diagnostics for guidance of experienced mechanics.
Please peruse and utilize this manual
fully to ensure complete repair work for
satisfying our customers by keeping
their vehicle in optimum condition.
When replacement of parts during
repair work is needed, be sure to use
SUBARU genuine parts.
All information, illustration and specifications contained in this manual are
based on the latest product information
available at the time of publication
approval.
FUJI HEAVY INDUSTRIES LTD.
HVAC SYSTEM
(HEATER, VENTILATOR AND A/C)
AC
HVAC SYSTEM (AUTO A/C)
(DIAGNOSTICS)
AC(diag)
AIRBAG SYSTEM
AB
AIRBAG SYSTEM (DIAGNOSTICS)
AB(diag)
SEAT BELT SYSTEM
SB
LIGHTING SYSTEM
LI
WIPER AND WASHER SYSTEMS
WW
ENTERTAINMENT
ET
COMMUNICATION SYSTEM
COM
GLASS/WINDOWS/MIRRORS
GW
BODY STRUCTURE
BS
INSTRUMENTATION/DRIVER INFO
IDI
SEATS
SE
SECURITY AND LOCKS
SL
SUNROOF/T-TOP/CONVERTIBLE TOP
(SUNROOF)
SR
EXTERIOR/INTERIOR TRIM
EI
EXTERIOR BODY PANELS
EB
G2320GE7
2003 LEGACY SERVICE MANUAL
QUICK REFERENCE INDEX
BODY SECTION
CRUISE CONTROL SYSTEM
CC
CRUISE CONTROL SYSTEM
(DIAGNOSTICS)
CC(diag)
IMMOBILIZER (DIAGNOSTICS)
IM(diag)
LAN SYSTEM (DIAGNOSTICS)
LAN(diag)
G2320GE7
EXTERIOR/INTERIOR TRIM
EI
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
Page
General Description ....................................................................................2
Front Grille ................................................................................................24
Front Hood Grille.......................................................................................25
Front Under Cover ....................................................................................26
Floor Under Protector................................................................................27
Fuel Tank Protector...................................................................................28
Mud Guard ................................................................................................29
Front Bumper ............................................................................................30
Rear Bumper.............................................................................................37
Cowl Panel ................................................................................................39
Roof Spoiler ..............................................................................................40
Side Sill Spoiler .........................................................................................41
Side Protector ...........................................................................................42
Side Garnish .............................................................................................44
Rear Quarter Protector..............................................................................45
Roof Molding .............................................................................................46
Roof Rail ...................................................................................................47
Door Trim ..................................................................................................48
Instrument Panel Lower Cover..................................................................50
Glove Box..................................................................................................51
Console Box..............................................................................................53
Center Console .........................................................................................54
Instrument Panel Assembly ......................................................................56
Lower Inner Trim .......................................................................................60
Upper Inner Trim .......................................................................................62
Rear Quarter Trim .....................................................................................63
Sun Visor...................................................................................................65
Assist Grip.................................................................................................66
Roof Trim ..................................................................................................67
Rear Gate Trim .........................................................................................69
Rear Shelf Trim .........................................................................................70
Trunk Room Trim ......................................................................................71
Floor Mat ...................................................................................................73
Luggage Floor Box....................................................................................74
Trunk Lid Garnish......................................................................................75
Rear Gate Garnish ....................................................................................76
Heat Shield Cover .....................................................................................77
Ornament ..................................................................................................78
General Description
EXTERIOR/INTERIOR TRIM
1. General Description
A: COMPONENT
1. FRONT GRILLE
(3)
(1)
(2)
EI-00627
(1)
Front grille
(2)
Front grille emblem
(3)
Front grille clip
2. UNDER COVER
T
EI-00681
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 14 (1.42, 10.3)
EI-2
General Description
EXTERIOR/INTERIOR TRIM
3. UNDER PROTECTOR
(2)
(3)
(4)
(4)
(1)
EI-00799
(1)
(2)
Floor under protector
Fuel tank protector RH
(3)
Fuel tank protector LH
EI-3
(4)
Plastic nut
General Description
EXTERIOR/INTERIOR TRIM
4. FRONT HOOD GRILLE
(1)
(2)
(3)
EI-00707
(1)
Front hood grille
(2)
Grille duct upper
EI-4
(3)
Grille duct lower
General Description
EXTERIOR/INTERIOR TRIM
5. FRONT BUMPER
T2
T2
(9)
T2
(7)
(10)
(11)
T2
T2
(14)
(12)
(8)
(1)
(13)
T1
(5)
(2)
(6)
(4)
(3)
EI-00795
(1)
(2)
(3)
(4)
(5)
(6)
Bumper face
Towing hook cover
Fog light cover
Lower side bracket
Upper bracket
Side bracket
(7)
(8)
(9)
(10)
(11)
(12)
Energy absorber foam upper
Energy absorber foam lower
Main beam reinforcement
Main beam bracket
Bracket support
Energy absorber side
EI-5
(13)
(14)
Lower center bracket
Radiator guide
Tightening torque: N⋅m (kgf-m, ft-lb)
T1: 7.5 (0.77, 5.5)
T2: 33 (3.4, 24)
General Description
EXTERIOR/INTERIOR TRIM
6. REAR BUMPER (SEDAN MODEL)
(3)
(8)
T
T
(9)
(4)
(1)
(6)
(2)
(7)
(5)
EI-00796
(1)
(2)
(3)
(4)
Bumper face
Exhaust end cover
Beam upper rear
Bracket corner
(5)
(6)
(7)
(8)
Lower bracket
Bumper side support upper
Bumper side support lower
Beam main reinforcement
EI-6
(9)
Bumper beam bracket
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 33 (3.4, 24)
General Description
EXTERIOR/INTERIOR TRIM
7. REAR BUMPER (WAGON MODEL)
(3)
(8)
T
T
(9)
(1)
(4)
(6)
(2)
(7)
(5)
EI-00797
(1)
(2)
(3)
(4)
Bumper face
Exhaust end cover
Beam upper rear
Bracket corner
(5)
(6)
(7)
(8)
Lower bracket
Bumper side support upper
Bumper side support lower
Beam main reinforcement
EI-7
(9)
Bumper beam bracket
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 33 (3.4, 24)
General Description
EXTERIOR/INTERIOR TRIM
8. MUD GUARD
(2)
(1)
EI-00835
(1)
Front mud guard
(2)
Rear mud guard
9. COWL PANEL
(4)
(3)
(1)
(2)
(4)
(3)
(1)
(2)
Cowl panel
Weather strip
(3)
Cover cowl panel
EI-8
(4)
Cowl side panel
EI-00832
General Description
EXTERIOR/INTERIOR TRIM
10.ROOF SPOILER
(1)
T
(3)
T
(2)
T
EI-00833
(1)
(2)
Roof spoiler
High-mounted stop light
(3)
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 4.5 (0.46, 3.32)
Washer nozzle
11.SIDE SILL SPOILER
(3)
(1)
(2)
EI-00733
(1)
Side sill spoiler
(2)
Double-sided tape
EI-9
(3)
Air flap side sill end
General Description
EXTERIOR/INTERIOR TRIM
12.ROOF MOLDING
T
(1)
(3)
T
(2)
T
(4)
T
(2)
(4)
T
(3)
T
EI-00752
(1)
(2)
Roof molding
Roof carrier attachment
(3)
(4)
Clip
Roof carrier attachment bracket
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 4.5 (0.46, 3.32)
13.SIDE PROTECTOR
(2)
(1)
EI-00829
(1)
Front door protector
(2)
Rear door protector
EI-10
General Description
EXTERIOR/INTERIOR TRIM
14.SIDE GARNISH
(4)
(3)
(1)
(2)
EI-00800
(1)
(2)
Front fender garnish
Front door garnish
(3)
Rear door garnish
(4)
Rear quarter garnish
15.TRUNK LID GARNISH
EI-00806
EI-11
General Description
EXTERIOR/INTERIOR TRIM
16.REAR GATE GARNISH
(6)
(1)
(2)
(4)
(3)
(5)
EI-00807
(1)
(2)
Rear gate garnish
Ornament
(3)
(4)
License plate light
Rear fog light or back-up light
EI-12
(5)
(6)
Back-up light or rear fog light
License plate light bracket
General Description
EXTERIOR/INTERIOR TRIM
17.DOOR TRIM
(4)
(3)
(9)
(6)
(5)
(12)
(7)
(4)
(5)
(6)
(8)
(3)
(2)
(7)
(8)
(9)
(1)
(10)
(11)
EI-00714
(1)
(2)
(3)
(4)
Front door trim
Gusset cover
Upper weather strip
Inner remote cover
(5)
(6)
(7)
(8)
Door grip
Door grip bracket upper
Door grip frame
Door grip bracket lower
EI-13
(9)
(10)
(11)
(12)
Power window switch
Step light cover
Speaker cover
Rear door trim
General Description
EXTERIOR/INTERIOR TRIM
18.CONSOLE BOX
(8)
(6)
(10)
(9)
(1)
(2)
(7)
(3)
(11)
(12)
A
A
(13)
(4)
(5)
EI-00812
(1)
(2)
(3)
(4)
(5)
Upper lid
Console cover
Seat heater switch
Front cup holder
Console box outer
(6)
(7)
(8)
(9)
(10)
Rear lid
Rear cup holder
Ash tray
Lid hinge
Parking brake lever boot
EI-14
(11)
(12)
Console pocket
Front accessory power supply
socket
(13)
Console box harness
General Description
EXTERIOR/INTERIOR TRIM
19.INSTRUMENT PANEL
T
(2)
(9)
T
(1)
T
(3)
T
(10)
(11)
(13)
(7)
(4)
(14)
(12)
(6)
(15)
(8)
(5)
EI-00813
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Steering support beam bracket
Steering support beam
Instrument panel pad & frame
ASSY
Instrument panel side cover
Glove box lower cover
Console side panel RH
Console side panel LH
(8)
(9)
Console side garnish
Instrument panel lower cover
upper
(10)
Instrument panel lower cover
under
(11)
(12)
Ash tray holder
Front accessory power supply
socket
EI-15
(13)
(14)
(15)
Console front panel (AT model)
Console front panel (MT model)
Shift lever boot
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 25 (25.5, 18.4)
General Description
EXTERIOR/INTERIOR TRIM
(1)
(2)
(4)
(3)
(8)
(9)
(10)
(6)
(12)
(11)
(5)
(7)
(14)
(13)
EI-00814
(1)
(2)
(3)
(4)
(5)
Air vent side duct
Air vent center duct
Instrument panel pad & frame
Air vent defroster grille
Air vent side grille
(6)
Navigation unit bracket (Model
with navigation system)
(7)
(8)
(9)
Glove box panel
Center console frame
Air vent center grille
EI-16
(10)
(11)
(12)
(13)
(14)
Audio bracket (LH)
Audio bracket (RH)
Center panel
Glove box
Glove box lid
General Description
EXTERIOR/INTERIOR TRIM
20.INNER TRIM (SEDAN MODEL)
(21)
(20)
(18)
(19)
(17)
(13)
(16)
(15)
(5)
(10)
(22)
(14)
(11)
(1)
(8)
(6)
(9)
(12)
(23)
(24)
(3)
(7)
(2)
(4)
(11)
EI-00715
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
Front pillar upper trim
Front pillar lower trim
Front outside scuff plate
Front inside scuff plate
Center pillar upper trim
Center pillar lower trim
Seat belt lower anchor bolt cover
Rear outside scuff plate
Rear inside scuff plate
Seat belt shoulder anchor adjuster
button
(11)
Bolt cover (Model with curtain airbag)
(20)
Curtain airbag guide center
(Model with curtain airbag)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
Center pillar inner protector lower
Center pillar inner protector upper
Front pillar inner protector lower
Front pillar inner protector upper
Roof side inner protector front
Roof side inner protector center
Roof side inner protector rear
Curtain airbag guide front (Model
with curtain airbag)
(21)
Curtain airbag guide rear (Model
with curtain airbag)
(22)
(23)
Rear quarter trim
Rear quarter trim front (Model with
curtain airbag)
(24)
Rear quarter trim rear (Model with
curtain airbag)
EI-17
General Description
EXTERIOR/INTERIOR TRIM
21.INNER TRIM (WAGON MODEL)
(21)
(20)
(18)
(19)
(17)
(23)
(16)
(22)
(13)
(15)
(5)
(24)
(14)
(10)
(11)
(11)
(1)
(8)
(6)
(12)
(9)
(3)
(7)
(2)
(4)
EI-00716
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
Front pillar upper trim
Front pillar lower trim
Front outside scuff plate
Front inside scuff plate
Center pillar upper trim
Center pillar lower trim
Seat belt lower anchor bolt cover
Rear outside scuff plate
Rear inside scuff plate
Seat belt shoulder anchor adjuster
button
(11)
Bolt cover (Model with curtain airbag)
(19)
Curtain airbag guide front (Model
with curtain airbag)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
Center pillar inner protector lower
Center pillar inner protector upper
Front pillar inner protector lower
Front pillar inner protector upper
Roof side inner protector front
Roof side inner protector center
Roof side inner protector rear
(20)
Curtain airbag guide center
(Model with curtain airbag)
(21)
Curtain airbag guide rear (Model
with curtain airbag)
(22)
(23)
(24)
Rear quarter front pillar trim
Rear quarter rear pillar trim
Rear quarter lower trim
EI-18
General Description
EXTERIOR/INTERIOR TRIM
22.REAR GATE TRIM
(1)
(2)
(3)
EI-00808
(1)
Rear gate panel upper trim
(2)
Rear gate panel pillar trim
(3)
Rear gate panel lower trim
23.ROOF TRIM (SEDAN MODEL)
EI-00755
EI-19
General Description
EXTERIOR/INTERIOR TRIM
24.ROOF TRIM (WAGON MODEL)
EI-00756
25.TRUNK ROOM TRIM
(5)
(1)
(4)
(2)
(6)
(3)
EI-00722
(1)
(2)
Trunk lid trim
Trunk lid arm cover
(3)
(4)
Trunk room mat
Trunk side trim
EI-20
(5)
(6)
Combination light cover
Trunk room end cover
General Description
EXTERIOR/INTERIOR TRIM
26.LUGGAGE FLOOR MAT
(5)
(7)
(4)
(2)
(6)
(1)
(3)
EI-00757
(1)
(2)
(3)
Front floor mat
Floor box (RH)
Floor box (LH)
(4)
(5)
(6)
Center floor mat
Side floor mat (RH)
Side floor mat (LH)
EI-21
(7)
Luggage floor end cover
General Description
EXTERIOR/INTERIOR TRIM
27.ROOM INNER PARTS
(4)
(1)
(2)
T
T
T
T
(3)
T
T
(3)
E
E
T
T
E
EI-00789
(1)
(2)
Room mirror
Sun visor
(3)
(4)
Tightening torque: N⋅m (kgf-m, ft-lb)
T: 7.4 (0.75, 5.46)
Assist grip
Coat hook (Wagon model)
28.HEAT SHIELD COVER
(5)
(6)
(3)
(1)
(4)
(2)
EI-00798
(1)
Front heat shield cover (5AT
model)
(3)
Center heat shield cover (Turbo
model)
(2)
Front heat shield cover (4AT
model and MT model)
(4)
Center heat shield cover (Nonturbo model)
EI-22
(5)
(6)
Rear heat shield cover RH
Rear heat shield cover LH
General Description
EXTERIOR/INTERIOR TRIM
B: PREPARATION TOOL
TOOL NAME
Clip remover
Clip clamp pliers
REMARKS
Used for removal of trim.
Used for removal of various clips and clamps.
EI-23
Front Grille
EXTERIOR/INTERIOR TRIM
2. Front Grille
A: REMOVAL
1) Open the hood.
2) Remove the push clips (A) and front grille clips
(B) from each side of front grille.
(B)
(B)
(A)
(A)
EI-00551
3) Remove the clips on the back side of front grille.
4) Pull lower side of the front grille forward, remove
hooks (A), and then remove the front grille from vehicle body.
(A)
EI-00552
B: INSTALLATION
Install in the reverse order of removal.
EI-24
Front Hood Grille
EXTERIOR/INTERIOR TRIM
3. Front Hood Grille
2) Insert the hooks (B) of the front hood duct into
holes (A) of the front hood.
A: REMOVAL
1) Open the front hood.
2) Remove the front hood insulator. <Ref. to EB13, FRONT HOOD INSULATOR, REMOVAL,
Front Hood.>
3) Remove the screws (A) and clip (B), and remove
the front hood duct.
(A)
(B)
(B)
EI-00634
3) Install the front hood duct with the screws (A)
and clip (B).
(B)
(A)
(A)
EI-00632
4) Loosen the nuts (A), remove the clip (B), and
then remove the front hood grille.
(A)
(A)
EI-00632
(A)
(B)
(A)
EI-00633
B: INSTALLATION
1) Fit the clip (B) of front hood grille, and install the
front hood grille using nuts (A).
(A)
(B)
(A)
EI-00633
Tightening torque:
4.5 N⋅m (0.46 kgf-m, 3.32 ft-lb)
EI-25
Front Under Cover
EXTERIOR/INTERIOR TRIM
4. Front Under Cover
A: REMOVAL
1) Lift-up the vehicle.
2) Remove the clips (A), (C) and bolts (B) in front
fender, and then remove the front under cover.
• Large type (Turbo model)
(C)
(A)
(A)
(B)
EI-00735
• Large type (DOHC non-turbo model)
(A)
(A)
(B)
EI-00635
• Small type (SOHC non-turbo model)
(A)
(A)
(A)
(B)
(A)
EI-00636
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
14 N⋅m (1.42 kgf-m, 10.3 ft-lb)
EI-26
Floor Under Protector
EXTERIOR/INTERIOR TRIM
5. Floor Under Protector
A: REMOVAL
1) Lift-up the vehicle.
NOTE:
Plate type lift can not be used.
2) Remove the push turn clips (A) and bolts (B),
and remove the floor under protector.
(A)
(A)
(B)
(A)
(A)
(B)
(A)
(A)
(A)
(B)
(A)
(A)
(A)
EI-00637
B: INSTALLATION
Install in the reverse order of removal.
EI-27
Fuel Tank Protector
EXTERIOR/INTERIOR TRIM
6. Fuel Tank Protector
A: REMOVAL
1) Lift-up the vehicle.
2) Remove the bolts (A) and plastic nuts (B), and
then remove the fuel tank protector.
(A)
(A)
(B)
(B)
(A)
(B)
(A)
(B)
(A)
(A)
EI-00638
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Bolt
17.5 N⋅m (1.78 kgf-m, 12.9 ft-lb)
EI-28
Mud Guard
EXTERIOR/INTERIOR TRIM
7. Mud Guard
A: REMOVAL
1. FRONT MUD GUARD
1) Jack-up the vehicle.
2) Remove the front wheels.
3) Loosen the screws and clips to remove mud
guard.
EI-00639
2. REAR MUD GUARD
1) Jack-up the vehicle.
2) Remove the rear wheels.
3) Loosen the screws and clips to remove mud
guard.
EI-00640
B: INSTALLATION
1. FRONT MUD GUARD
Install in the reverse order of removal.
2. REAR MUD GUARD
Install in the reverse order of removal.
EI-29
Front Bumper
EXTERIOR/INTERIOR TRIM
8. Front Bumper
2. FRONT BUMPER BEAM ASSEMBLY
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the front grille. <Ref. to EI-24, REMOVAL, Front Grille.>
3) Remove the front bumper face. <Ref. to EI-30,
FRONT BUMPER FACE, REMOVAL, Front
Bumper.>
4) Remove the energy absorber foam from bumper
beam.
1. FRONT BUMPER FACE
1) Disconnect the ground cable from battery.
2) Remove the front grille. <Ref. to EI-24, REMOVAL, Front Grille.>
3) Turn over the front mud guard, and remove the
clips connecting the fender and bumper.
EI-00575
5) Remove the bolts, and remove the bumper
beam assembly from vehicle body.
EI-00572
4) Remove the clips at the lower side of bumper.
EI-00576
NOTE:
After all bolts are removed, raise the whole bumper
beam a little to remove it from vehicle body.
6) Remove the bolts and nuts, and disassemble the
bumper beam.
EI-00573
5) Disconnect the fog light connector. (Model with
fog light)
6) Remove the bumper from vehicle body.
7) Remove the fog light from bumper face. <Ref. to
LI-21, REMOVAL, Front Fog Light Assembly.>
EI-30
EI-00577
Front Bumper
EXTERIOR/INTERIOR TRIM
7) Remove the clips, and remove the radiator
guide.
EI-00801
8) Remove the bolts and clips, and remove the
bumper lower center bracket.
EI-00578
B: INSTALLATION
1. FRONT BUMPER FACE
1) Install in the reverse order of removal.
2) Fit the slider (A) to the guide plate (B) securely.
(B)
(A)
EI-00571
2. FRONT BUMPER BEAM ASSEMBLY
Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Description”. <Ref. to EI-5, FRONT BUMPER, COMPONENT, General Description.>
EI-31
Front Bumper
EXTERIOR/INTERIOR TRIM
C: REPAIR
1. COATING METHOD FOR PP BUMPER
Process
No.
Process name
Job contents
(1)
1
Bumper installation
Place the bumper on a paint worktable as
required. Use the paint worktable conforming
to inner shape of bumper when possible.
(2)
2
Masking
4
Degreasing, cleaning
Primer paint
5
Drying
6
Top coat paint (I)
7
Drying
8
Top coat paint (II)
9
Drying
10
11
Inspection
Masking removal
3
EI-00234
(1) Bumper
(2) Set bumper section
Mask specified part (black base) with masking tape. Use masking tape for PP (example,
Nichiban No. 533, etc.).
Clean all parts to be painted with white gasoline, normal alcohol, etc. to remove dirt, oil, fat, etc.
Apply primer to all parts to be painted, using spray gun. Use primer (clear).
Dry at normal temperature [10 — 15 min. at 20°C (68°F)].
In half-dried condition, PP primer paint is dissolved by solvent, e.g. thinner, etc.
Therefore, if dust or dirt must be removed, use ordinary alcohol, etc.
Non-colored
Metallic paint
Use section (block) paint for top coat.
Use section (block) paint for top coat.
• Paint to be used (for each color):
• Paint to be used (for each color):
Metallic paint
Solid paint
Hardener PB
Hardener PB
Thinner T-306
Thinner T-301
• Mixing ratio:
• Mixing ratio:
Main agent vs. hardener = 10:1
Main agent vs. hardener = 4:1
• Viscosity: 10 — 13 sec./20°C (68°F)
• Viscosity: 10 — 13 sec./20°C (68°F)
• Film thickness: 15 — 20 µ
• Film thickness: 35 — 45 µ
• Spraying pressure: 245 — 343 kPa
• Spraying pressure: 245 — 343 kPa
(2.5 — 3.5 kg/cm2, 36 — 50 psi)
(2.5 — 3.5 kg/cm2, 36 — 50 psi)
Dry at normal temperature [more than 10 min.
Not required.
at 20°C (68°F)].
In half-dried condition, avoid dust, dirt.
Apply a clear coat to parts with top coat paint
(I), three times, at 5 — 7 minutes intervals.
• Paint to be used:
Metallic paint
Hardener PB
Thinner T-301
Not required.
• Mixing ratio:
Clear coat vs. hardener = 6:1
• Viscosity: 14 — 16 sec./20°C (68°F)
• Film thickness: 25 — 30 µ
• Spraying pressure: 245 — 343 kPa
(2.5 — 3.5 kg/cm2, 36 — 50 psi)
60°C (140°F), 60 min. or 80°C (176°F), 30 min.
If higher than 80°C (176°F), PP may be deformed. Keep maximum temperature at 80°C (176°F).
Paint check.
Remove masking tape applied in process No. 2.
EI-32
Front Bumper
EXTERIOR/INTERIOR TRIM
2. REPAIR INSTRUCTIONS FOR COLORED PP BUMPER
NOTE:
All PP bumpers are provided with a grained surface, and if the surface is damaged, it cannot normally be restored to its former condition. Damages limited to the shallow scratches that cause only a change in the luster
of the base material or coating, can be almost fully restored. Before repairing a damaged area, explain this
point to the customer and obtain an understanding about the matter. Repair methods are outlined below,
based on a classification of the extent of damage.
1) Minor damage causing only a change in the lustre of the bumper due to a light touch
Almost restorable.
Process
No.
1
2
3
Process name
Cleaning
Sanding
Finish
Job contents
Clean the area to be repaired using water.
Grind the repairing area with #500 sand paper in a “feathering” motion.
Resin section
Coated section
Repeatedly apply wax to the affected area
using a soft cloth (such as flannel). RecomPerform either the same process as for the
mended wax: NITTO KASEI Soft 99 TIRE
resin section or process No. 18 and subseWAX BLACK, or equivalent.
quent in the “3)” section, depending on the
Polish the waxed area with a clean cloth after 5 degree and nature of damage.
to 10 minutes.
2) Deep damage caused by scratching with fences, etc.
A dent cannot be repaired but a whitened or swelled part can be removed.
Process
No.
1
Process name
3
Cleaning
Removal of damaged area
Sanding
4
Finish
2
Job contents
Clean damaged area with water.
Cut off protruding area, if any, due to collision, using a putty knife.
Grind the affected area with #100 to #500 sand paper.
Resin section
Coated section
Perform Process No. 12 and subsequent operSame as Process No. 3 in the “1)” section.
ations in the “3)” section.
EI-33
Front Bumper
EXTERIOR/INTERIOR TRIM
3) Deep damage such as a break or hole that requires filling
Much of the peripheral grained surface must be sacrificed for repair. The degree of restoration is not really
worth the expense. (The surface, however, will become almost flush with adjacent areas.)
Recommended repair kit: PP Part Repair Kit (NRM)
Process
No.
1
2
Process name
Bumper removal
Removal of parts
Job contents
Remove the bumper as required.
Remove the parts built into bumper as required.
(1)
3
Bumper placement
Place the bumper on a paint worktable as
required.
It is recommended to use the paint worktable
conforming to internal shape of bumper.
(2)
4
Surface preparation
EI-00234
(1) Bumper
(2) Set bumper section
Remove dust, oil, etc. from areas to be repaired and surrounding areas, using a suitable solvent
(NRM No. 900 Precleno, white gasoline, or alcohol, etc.).
(3)
(1)
5
6
7
Cutting
Sanding (I)
Cleaning
If nature of damage are cracks or holes, cut a
guide slit of 20 to 30 mm (0.79 to 1.18 in) in
length along the crack or hole up to the
bumper’s base surface. Then, bevel or “veeout” the affected area using a knife or grinder.
(4)
(2)
EI-00235
(1) Paint surface
(2) PP base surface
(3) 20 — 30 mm (0.79 — 1.18 in)
(4) 3 mm (0.12 in)
Grind beveled surface with sand paper (#40 to #60) to smooth finish.
Clean the sanded surface with the same solvent as used in Process No. 4.
Grind the side just opposite the beveled area with sand paper (#40 to #60) and clean using a solvent.
Temporarily spot-weld the side, using a PP welding rod and heater gun.
(1)
8
Temporary welding
(2)
(3)
(1) Welded point (Use heater gun and PP welding rod)
(2) PP base surface
(3) Beveled section
NOTE:
• Do not melt welding rod until it flows out. This results in reduced strength.
• Leave the welded spot unattended until it cools completely.
EI-34
EI-00236
Front Bumper
EXTERIOR/INTERIOR TRIM
Process
No.
Process name
Job contents
Using a heater gun and PP welding rod, weld the beveled spot while melting the rod and damaged area.
(2)
(2)
9
Welding
(3)
(1)
EI-00237
(1) Welding rod
(2) Melt hatched area
(3) Section
NOTE:
• Melt the sections indicated by hatched area.
• Do not melt the welding rod until it flows out, in order to provide strength.
• Always keep the heater gun 1 to 2 cm (0.4 to 0.8 in) away from the welding spot.
• Leave the welded spot unattended until it cools completely.
Remove excess part of weld with a putty knife. If a drill or disc wheel is used instead of the knife,
operate it at a rate lower than 1,500 rpm and grind the excess part little by little. A higher rpm will
cause the PP substrate to melt from the heat.
10
Sanding (II)
EI-00042
11
Masking
12
Cleaning/ degreasing
13
Primer coating
14
Leave unattended
15
Primer surfacer
coating
Sand the welded spot smooth with #240 sand paper.
Mask the black substrate section using masking tape.
Recommended masking tape: Nichiban No. 533 or equivalent
Completely clean the entire coated area, using solvent similar to that used in Process No. 4.
Apply a coat of primer to the repaired surface and its surrounding areas. Mask these areas, if
necessary.
Recommended primer: Mp/ 364 PP Primer
NOTE:
Be sure to apply coat of primer at a spraying pressure of 245 — 343 kPa (2.5 — 3.5 kg/cm2, 36
— 50 psi) with a spray gun.
Leave the repaired area unattended at 20°C (68°F) for 10 to 15 minutes until primer is half-dry.
NOTE:
If dirt or dust comes in contact with the coated area, wipe it off with a cloth with alcohol. (Do not
use thinner since the coated area tends to melt.)
Apply a coat of primer surfacer to the repaired area two or three times at an interval of 3 to 5 minutes.
Recommended surfacer:
• UPS 300 Flex Primer
• No. 303 UPS 300 Exclusive hardener
• NPS 725 Exclusive Reducer (thinner)
• Mixing ratio:
2 : 1 (UPS 300 : No. 303)
• Viscosity: 12 — 14 sec./20°C (68°F)
• Coating film thickness: 40 — 50 µ
EI-35
Front Bumper
EXTERIOR/INTERIOR TRIM
Process
No.
16
17
18
19
20
21
22
23
24
25
26
Process name
Drying
Sanding (III)
Cleaning/ degreasing
Job contents
Allow the coated surface to dry for 20 minutes at 20°C (68°F) [or 30 minutes at 60°C (140°F)].
Sand the coated surface and its surrounding areas using #400 sand paper and water.
Same as Process No. 12.
Non-colored
Use a “block” coating method.
• Recommended paint:
Suncryl (SC)
No. 307 Flex Hardener
SC Reducer (thinner)
• Mixing ratio:
Suncryl (SC) vs. No. 307 Flex Hardener = 3 : 1
• Viscosity: 11 — 13 sec./20°C (68°F)
• Coating film thickness: 40 — 50 µ
• Spraying pressure: 245 — 343 kPa
(2.5 — 3.5 kg/cm2, 36 — 50 psi)
Metallic paint
Use a “block” coating method.
• Recommended paint:
Suncryl (SC)
No. 307 Flex Hardener
SC Reducer (thinner)
Top coat (I)
• Mixing ratio:
Suncryl (SC) vs. No. 307 Flex Hardener = 3 : 1
• Viscosity: 11 — 13 sec./20°C (68°F)
• Coating film thickness: 20 — 30 µ
• Spraying pressure: 245 — 343 kPa
(2.5 — 3.5 kg/cm2, 36 — 50 psi)
Leave unattended at 20°C (68°F) for at least 10
minutes until the topcoated area is half-dry.
Leave unattended
Not required.
NOTE:
Be careful to keep dust or dirt from coming in
contact with the affected area.
Apply a clear coat three times at an interval of 3
to 5 minutes.
• Recommended paint:
SC710 Overlay Clear
No. 307 Flex Hardener
SC Reducer (thinner)
Top coat (II)
Not required.
• Mixing ratio:
Suncryl (SC) vs. No. 307 Flex Hardener = 3 : 1
• Viscosity: 10 — 13 sec./20°C (68°F)
• Coating film thickness: 20 — 30 µ
• Spraying pressure: 245 — 343 kPa
(2.5 — 3.5 kg/cm2, 36 — 50 psi)
Allow the coated surface to dry for 2 hours at 20°C (68°F) or 30 minutes at 60°C (140°F).
Drying
NOTE:
Do not allow the temperature to exceed 80°C (176°F) since this will deform the PP substrate.
Inspection
Carefully check the condition of the repaired area.
Masking removal
Remove the masking tape applied in Process No. 11 and 13.
Parts installation
Install parts on the bumper in reverse order of removal.
Bumper installation Install the bumper.
EI-36
Rear Bumper
EXTERIOR/INTERIOR TRIM
9. Rear Bumper
• Sedan model: trunk side trim
A: REMOVAL
1. REAR BUMPER FACE
1) Disconnect the ground cable from battery.
2) Remove the rear combination light assembly.
<Ref. to LI-25, REMOVAL, Rear Combination Light
Assembly.>
3) Remove the two clips.
EI-00583
• Wagon model: rear quarter lower trim
EI-00579
4) Turn over the mud guard, and remove the bolt
(A) inside wheel house, and the clips (B) on the
lower side of bumper.
NOTE:
For model with McIntosh Audio, remove the woofer
cover.
(A)
(B)
EI-00584
EI-00580
5) Remove the clips on the lower side of rear
bumper.
EI-00585
7) Remove the rear bumper from vehicle body.
EI-00581
6) Remove the service hole cover, and remove the
bolt.
EI-00802
NOTE:
• Do not pull with a excessive force. Otherwise the
bracket installation area may be damaged.
• Remove from the end in order.
EI-37
Rear Bumper
EXTERIOR/INTERIOR TRIM
2. REAR BUMPER BRACKET
1) Remove the rear bumper face from vehicle
body.
2) Remove the rear bumper bracket corner from
vehicle body. (both sides)
3) Remove the nuts, and remove the beam main
reinforcement from vehicle body.
EI-00803
4) Remove the nuts, and remove the bumper beam
bracket and beam upper rear from vehicle body.
EI-00587
3) Remove the lower brackets from vehicle body.
• Sedan model: 2 places
EI-00804
B: INSTALLATION
1. REAR BUMPER FACE
EI-00641
1) Install the beam upper rear to vehicle body.
2) Install the bumper face to vehicle body.
• Wagon model: 4 places
NOTE:
If the bumper face is easily come off the beam upper rear, adjust the hook area of the bracket side.
3) Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Description”.
<Ref. to EI-6, REAR BUMPER (SEDAN MODEL), COMPONENT, General Description.>
EI-00588
3. REAR BUMPER BEAM ASSEMBLY
2. REAR BUMPER BRACKET
1) Disconnect the ground cable from battery.
2) Remove the rear bumper face. <Ref. to EI-37,
REAR BUMPER FACE, REMOVAL, Rear
Bumper.>
Install in the reverse order of removal.
3. REAR BUMPER BEAM ASSEMBLY
Install in the reverse order of removal.
C: REPAIR
Refer to the description for front bumper repair.
<Ref. to EI-30, REMOVAL, Front Bumper.>
EI-38
Cowl Panel
EXTERIOR/INTERIOR TRIM
10.Cowl Panel
5) Remove the cowl panel side and clip (A).
A: REMOVAL
(A)
1) Open the hood.
2) Remove the wiper arm. <Ref. to WW-17, REMOVAL, Front Wiper Arm.>
3) Remove the weather strip clip, and remove the
weather strip.
EI-00790
6) Remove the clips (A), and remove the cowl panel.
EI-00642
NOTE:
If the weather strip clip is removed with excessive
force, the weather strip may be damaged. Be sure
to use a clip remover to remove.
:(A)
B: INSTALLATION
Install in the reverse order of removal.
EB-00141
4) Remove the clip, and remove the cover cowl
panel.
EI-00643
EI-39
EI-00644
Roof Spoiler
EXTERIOR/INTERIOR TRIM
11.Roof Spoiler
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear gate trim. <Ref. to EI-69, REMOVAL, Rear Gate Trim.>
3) Disconnect the connector of the high mounted
stop light and the washer hose of rear washer.
4) Remove the cap nut and plastic caps.
EI-00828
5) Remove the clips, and remove the roof spoiler.
EI-00646
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
4.5 N⋅m (0.46 kgf-m, 3.32 ft-lb)
EI-40
Side Sill Spoiler
EXTERIOR/INTERIOR TRIM
12.Side Sill Spoiler
A: REMOVAL
Remove the clips (two for front fender arch area, six for side sill spoiler lower area), and remove the side
spoiler.
(3)
(1)
(2)
EI-00733
(1)
Side sill spoiler
(2)
Double-sided tape
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
For the rearmost clip securing side sill spoiler, install through the end cover.
(1)
(2)
(3)
EI-00791
(1) Vehicle body
(2) End cover
(3) Side sill spoiler
EI-41
(3)
End cover
Side Protector
EXTERIOR/INTERIOR TRIM
13.Side Protector
A: REMOVAL
(2)
(1)
EI-00829
(1)
Front door protector
(2)
Rear door protector
1) Slide in a thin thread (A) of 0.8 mm (0.031 in) diameter or less (fishing line etc.) between body and
protector, cut the double-sided tape, and pull the
protector toward you, and remove the clip using clip
remover.
• If the double-sided tape remains thick on the surface due to interfacial peeling, apply the solvent after slicing off the double-sided tape using a cutter.
(A)
(A)
(B)
(C)
EI-00478
(A) Panel
(B) Side protector
(C) Double-sided tape
EI-00153
NOTE:
• To optimize the effect of solvent, slide the thread
along body without removing the double-sided tape
on the surface of body and spoiler.
• If it is difficult to detach the double-sided tape,
warm up to approx. 40°C (104°F).
2) Apply masking tape around the double-sided
tape remaining on the surface of body or spoiler.
3) Apply solvent uniformly on double-sided tape using a brush.
CAUTION:
• Do not use the solvent to the body which is
repaired with lacquer paint.
• Wipe off immediately when the solvent is
touched on surface of the body or spoiler.
Solvent:
3M 8907 or equivalent
EI-42
Side Protector
EXTERIOR/INTERIOR TRIM
4) Cover the area where solvent is applied using
plastic wrap (A), and then heat the double-sided
tape for 5 to 10 minutes in 40 — 60°C (104 —
140°F) using a heat lamp (B).
(A)
Double-sided tape:
3M 5531-5 or equivalent
2) Heat the adhering part using a heat lamp.
Body side: 40 — 60°C (104 — 140°F)
Protector side: 20 — 30°C (68 — 86°F)
3) Detach the double-sided tape backing sheet,
align the clip position, and then adhere to the body
using care to avoid air entering.
CAUTION:
To keep the adhesion, do not wash the vehicle
within 24 hours from installation.
(B)
EI-00155
(A)
(B)
EI-00156
CAUTION:
Do not heat the double-sided tape until the surface becomes white and excessively dried.
5) Remove the double-sided tape using a plastic
spatula.
6) After completely removing the double-sided
tape, detach the masking tape and clean the surface using a cotton cloth damped with white gasoline.
B: INSTALLATION
1) Apply primer to the protector surface where the
double-sided tape to be adhered, and then adhere
the double-sided tape as shown in the figure.
(1)
(1)
EI-00536
(1) Double-sided tape: thickness 1.2 mm (0.047 in),
width 5mm (0.197 in)
Primer:
3M K-500 or equivalent
EI-43
Side Garnish
EXTERIOR/INTERIOR TRIM
14.Side Garnish
A: REMOVAL
EI-00805
For removal of side garnish, refer to the removal procedure of “Side Protector”. <Ref. to EI-42, REMOVAL,
Side Protector.>
EI-44
Rear Quarter Protector
EXTERIOR/INTERIOR TRIM
15.Rear Quarter Protector
A: REMOVAL
1) Remove the side sill spoilers. <Ref. to EI-41, REMOVAL, Side Sill Spoiler.>
2) Remove the clips (A) with rotating it rearward using the fender arch as a fulcrum, and then remove
the rear quarter protector.
: (A)
EI-00734
B: INSTALLATION
Install in the reverse order of removal.
EI-45
Roof Molding
EXTERIOR/INTERIOR TRIM
16.Roof Molding
5) Remove the nuts, and remove the roof carrier attachment.
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the roof carrier attachment cover, and
remove the bolts. (2 places for each side)
EI-00658
3) Pull the roof molding upward, and remove it from
vehicle body.
(2)
(1)
EI-00659
(5)
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Replace the clip with new one when the broken
pin grommet is found during the removal of
roof molding. When the body side cap or clip is
damaged, or the roof molding is lifted or peeled
from body, be sure to repair them correctly, because those troubles may cause the water leakage.
(4)
(3)
EI-00660
(1)
(2)
(3)
(4)
(5)
Locating pin
Roof molding
Cap
Clip
Grommet
4) Remove the roof trim. <Ref. to EI-67, REMOVAL, Roof Trim.>
Tightening torque:
7.5 N⋅m (0.76 kgf-m, 5.5 ft-lb)
EI-46
Roof Rail
EXTERIOR/INTERIOR TRIM
17.Roof Rail
A: REMOVAL
1) Remove the roof trim. <Ref. to EI-67, REMOVAL, Roof Trim.>
2) Remove the six nuts.
E
F
(A)
D
A
B
(B)
C
(C)
(D)
(E)
(F)
EI-00834
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
When removing or installing the roof rail, be
careful not to scratch the body panel with the
stud bolt of roof rail.
Tightening torque:
7.5 N⋅m (0.76 kgf-m, 5.53 ft-lb)
EI-47
Door Trim
EXTERIOR/INTERIOR TRIM
18.Door Trim
• Rear door trim
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the cover (A) at inner remote area.
(A)
EI-00656
B: INSTALLATION
Install in the reverse order of removal.
EI-00649
3) Pull the hand grip cover toward you, and remove
it.
NOTE:
Be careful not to install the hand grip cover and
plate clip of hand grip in the wrong direction.
• Hand grip cover (front and rear door)
Convex upward
EI-00650
4) Loosen the screws.
EI-00651
5) Remove the clips, and disconnect each connector and wire to remove door trim.
• Front door trim
EI-00653
• Bottom clip of the front door faces the opposite
direction
EI-00654
EI-00652
EI-48
Door Trim
EXTERIOR/INTERIOR TRIM
• Lower side of the hand grip cover for front door
has pawl part.
• The lowest clip of rear door faces the opposite direction
EI-00655
EI-49
Instrument Panel Lower Cover
EXTERIOR/INTERIOR TRIM
19.Instrument Panel Lower Cover
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the front door inside scuff plate (A) and
front pillar lower trim (B). <Ref. to EI-60, REMOVAL, Lower Inner Trim.>
(A)
(B)
EI-00758
3) Remove the clips, and remove the instrument
panel lower cover under.
EI-00759
4) Loosen the screw (A), disconnect the connectors, and remove the instrument panel lower cover
upper.
:(B)
(A)
EI-00760
(B) Clip
B: INSTALLATION
Install in the reverse order of removal.
EI-50
Glove Box
EXTERIOR/INTERIOR TRIM
20.Glove Box
6) Remove the clip, and remove the glove box lower cover.
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the console box. <Ref. to EI-53, REMOVAL, Console Box.>
3) Remove the console front panel.
EI-00764
7) Remove the console side panel.
: (A)
EI-00761
(A) Hook
NOTE:
For AT model, remove the ring indicator.
For MT model, remove the shift knob.
4) Remove the console side garnish.
EI-00765
8) Remove the instrument panel side cover, and remove the clip.
: (A)
EI-00762
(A) Hook
: (A)
5) Remove the front inside scuff plate (A) and front
pillar lower trim (B). <Ref. to EI-60, REMOVAL,
Lower Inner Trim.>
EI-00766
(A) Clip
9) Remove the screw, and remove the glove box.
(A)
(B)
EI-00763
: (A)
(A) Clip
EI-51
EI-00767
Glove Box
EXTERIOR/INTERIOR TRIM
B: INSTALLATION
Install in the reverse order of removal.
EI-52
Console Box
EXTERIOR/INTERIOR TRIM
21.Console Box
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the parking brake lever cover.
EI-00810
3) Remove the bolts and clips.
EI-00811
4) Disconnect the connector, and remove the console box.
B: INSTALLATION
Install in the reverse order of removal.
EI-53
Center Console
EXTERIOR/INTERIOR TRIM
22.Center Console
6) Remove the clip at the console side panel tip.
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the console box. <Ref. to EI-53, REMOVAL, Console Box.>
3) Remove the console front panel.
EI-00769
7) Remove the passenger side front inside scuff
plate (A) and front pillar lower trim (B). <Ref. to EI60, REMOVAL, Lower Inner Trim.>
: (A)
EI-00761
(A) Hook
NOTE:
For AT model, remove the ring indicator.
For MT model, remove the shift knob.
4) Loosen the screw, remove the hook, and remove the console side garnish.
(A)
(B)
EI-00763
8) Remove the clip, and remove the glove box lower cover.
: (A)
EI-00762
(A) Hook
EI-00764
5) Remove the instrument panel lower cover. <Ref.
to EI-50, REMOVAL, Instrument Panel Lower Cover.>
EI-00768
EI-54
Center Console
EXTERIOR/INTERIOR TRIM
9) Remove the screws, and remove the console
side panel.
EI-00770
10) Loosen the screws to pull out the audio unit assembly, and disconnect the connector to remove
audio unit.
EI-00794
NOTE:
Audio unit assembly can be removed without removing the console side panel.
B: INSTALLATION
Install in the reverse order of removal.
EI-55
Instrument Panel Assembly
EXTERIOR/INTERIOR TRIM
23.Instrument Panel Assembly
10) Remove the screw at the side of center console.
A: REMOVAL
1. INSTRUMENT PANEL (EXCLUDING
STEERING SUPPORT BEAM)
CAUTION:
Be careful to the harness of airbag system
when servicing the instrument panel. Damage
may cause the system malfunction.
1) Disconnect the ground cable from battery.
2) Remove the front pillar upper trim. <Ref. to EI62, REMOVAL, Upper Inner Trim.>
3) Remove the console box. <Ref. to EI-53, REMOVAL, Console Box.>
4) Remove the center console. <Ref. to EI-54, REMOVAL, Center Console.>
5) Remove the instrument panel lower cover. <Ref.
to EI-50, REMOVAL, Instrument Panel Lower Cover.>
6) Remove the glove box. <Ref. to EI-51, REMOVAL, Glove Box.>
7) Remove the combination meter assembly. <Ref.
to IDI-16, REMOVAL, Combination Meter Assembly.>
8) Remove the screws.
EI-00771
11) Remove the center air vent grille of instrument
panel. <Ref. to AC-44, CENTER GRILLE, REMOVAL, Air Vent Grille.>
12) Remove the screws.
EI-00772
13) Remove the screws at side of passenger side
instrument panel.
EI-00605
9) Remove the driver side instrument panel side
cover, and remove the screws.
EI-00773
14) Remove the bolts securing passenger side airbag module to the steering support beam.
EI-00609
EI-00610
15) Disconnect the connectors, and remove the instrument panel from vehicle body.
EI-56
Instrument Panel Assembly
EXTERIOR/INTERIOR TRIM
NOTE:
• If necessary, make matching marks for easy reassembly.
• When storing the removed instrument panel, be
sure to prepare a table or the like to put instrument
panel on to prevent damage.
16) Remove the side air vent grille. <Ref. to AC-44,
REMOVAL, Air Vent Grille.>
17) Remove the heater vent duct. <Ref. to AC-46,
REMOVAL, Heater Vent Duct.>
18) Loosen the screws to remove center console
frame.
21) Loosen the screws to remove glove box striker.
EI-00614
22) Remove the pawl, and remove the passenger’s
airbag module.
EI-00774
19) Loosen the screws to remove meter bracket.
EI-00615
2. STEERING SUPPORT BEAM
1) Remove the instrument panel. <Ref. to EI-56,
INSTRUMENT PANEL (EXCLUDING STEERING
SUPPORT BEAM), REMOVAL, Instrument Panel
Assembly.>
2) Remove the steering shaft assembly. <Ref. to
PS-23, REMOVAL, Tilt Steering Column.>
3) Remove each harness clip, and remove the harness from steering support beam.
EI-00612
20) Loosen the screws to remove instrument panel
matching pins.
NOTE:
If necessary, make matching marks for easy reassembly.
4) Remove the bolt and remove steering support
beam.
EI-00613
EI-00775
EI-57
Instrument Panel Assembly
EXTERIOR/INTERIOR TRIM
5) Remove the steering support beam bracket.
8) Loosen the bolts on the center console side.
EI-00617
EI-00620
9) Disconnect each connector, and remove the instrument assembly.
3. INSTRUMENT PANEL ASSEMBLY (INCLUDING STEERING SUPPORT BEAM)
CAUTION:
Be careful to the harness of airbag system
when servicing the instrument panel. Damage
may cause the system malfunction.
1) Remove the front pillar upper trim. <Ref. to EI62, REMOVAL, Upper Inner Trim.>
2) Remove the center console. <Ref. to EI-54, REMOVAL, Center Console.>
3) Remove the instrument panel lower cover. <Ref.
to EI-50, REMOVAL, Instrument Panel Lower Cover.>
4) Remove the glove box. <Ref. to EI-51, REMOVAL, Glove Box.>
5) Remove the steering shaft assembly. <Ref. to
PS-23, REMOVAL, Tilt Steering Column.>
6) Remove the driver side instrument panel side
cover, and remove the bolts.
NOTE:
If necessary, make matching marks for easy reassembly.
B: INSTALLATION
1. INSTRUMENT PANEL (EXCLUDING
STEERING SUPPORT BEAM)
1) Insert the matching pins (3 places) on the instrument panel tip into the grommet (A) and (B) on the
body panel side.
(B)
(A)
(B)
EI-00621
2) Check the inserted state of matching pins, and
pull the harness around.
3) Tighten the instrument panel with screw, and recheck the installation of instrument panel and the
state of pulled harness.
4) Install in the reverse order of removal.
EI-00776
7) Remove the bolts at the side of passenger side
instrument panel.
2. STEERING SUPPORT BEAM
1) Temporarily tighten the steering support beam
with bolt, and pull the harness around.
2) Make sure that there is no mutual interference in
each pedal, and tighten the each bolt.
Tightening torque:
25 N⋅m (25.5 kgf-m, 18.4 ft-lb)
3) Install in the reverse order of removal.
EI-00777
EI-58
Instrument Panel Assembly
EXTERIOR/INTERIOR TRIM
3. INSTRUMENT PANEL ASSEMBLY (INCLUDING STEERING SUPPORT BEAM)
1) Insert the matching pins (3 places) on the instrument panel tip into the grommet (A) and (B) on the
body panel side.
(B)
(A)
(B)
EI-00621
2) Check the inserted state of matching pins, and
pull the harness around.
3) Temporarily tighten the steering support beam
with bolt, and pull the harness around.
4) Make sure that there is no mutual interference in
each pedal, and tighten the each bolt.
Tightening torque:
25 N⋅m (25.5 kgf-m, 18.4 ft-lb)
5) Install in the reverse order of removal.
EI-59
Lower Inner Trim
EXTERIOR/INTERIOR TRIM
24.Lower Inner Trim
5) Remove the clip (A), and remove the inside scuff
plate.
A: REMOVAL
1) Remove the hook, and remove the inside scuff
plate.
(A)
: (B)
EI-00781
(B) Hook
: (A)
EI-00778
6) Remove the door molding (A) and door catcher
cover (B), and then remove the outside scuff plate.
(A) Hook
2) Remove the door molding (A), and remove the
outside scuff plate.
(A)
(A)
(B)
:(C)
: (B)
:(D)
EI-00782
(C) Hook with plate clip
(D) Clip
EI-00779
7) Remove the clips of the center pillar lower trim.
(B) Clip
3) Remove the clip (A), and remove the front pillar
lower trim.
(A)
EI-00783
EI-00780
4) Remove the rear seat cushion. <Ref. to SE-14,
REMOVAL, Rear Seat.>
EI-60
Lower Inner Trim
EXTERIOR/INTERIOR TRIM
8) Remove the center pillar lower trim while pushing the pawl part on the upper and lower side of
dropout prevention clip.
EI-00784
B: INSTALLATION
Install in the reverse order of removal.
EI-61
Upper Inner Trim
EXTERIOR/INTERIOR TRIM
25.Upper Inner Trim
5) Remove the center pillar upper trim.
A: REMOVAL
1) From the top side of trim, remove the metal clip
using flat tip driver.
EI-00787
6) Remove the seat belt lower anchor bolt cover.
EI-00785
CAUTION:
When metal clip is removed from upper inner
trim, replace the both of upper inner trim and
metal clip with new ones.
2) Remove the front pillar upper trim.
: (A)
EI-00788
(A) Clip
7) Remove the seat belt lower anchor bolt, and pull
out the seat belt from center pillar upper trim.
EI-00786
3) Remove the front inside scuff plate, rear inside
scuff plate and center pillar lower trim. <Ref. to EI60, REMOVAL, Lower Inner Trim.>
4) Remove the cap on the upper side of pillar trim,
and remove the bolt inside. (Model with curtain airbag)
SB-00145
B: INSTALLATION
Install in the reverse order of removal.
EI-00562
EI-62
Rear Quarter Trim
EXTERIOR/INTERIOR TRIM
26.Rear Quarter Trim
3) Remove the cap on the upper side of trim, and
remove the bolt inside.
A: REMOVAL
1. SEDAN MODEL (MODEL WITHOUT
CURTAIN AIRBAG)
1) Remove the rear seat. <Ref. to SE-14, SEDAN
MODEL, REMOVAL, Rear Seat.>
2) Remove the rear quarter trim.
EI-00562
4) Remove the bolts (A), and remove the quarter
trim (front).
(A)
(A)
EI-00838
2. SEDAN MODEL (MODEL WITH CURTAIN
AIRBAG)
1) Remove the rear seat. <Ref. to SE-14, WAGON
MODEL, REMOVAL, Rear Seat.>
2) Turn over the trim, and remove the quarter trim
rear by pressing the claw (A) of metal clip using flat
tip screwdriver or the like.
EI-00839
3. WAGON MODEL
1) Remove the rear seat cushion and backrest
shoulder. <Ref. to SE-14, SEDAN MODEL, REMOVAL, Rear Seat.>
2) Remove the cap on the upper side of pillar trim,
and remove the bolt inside. (Model with curtain airbag)
(A)
EI-00562
:(B)
EI-00682
(B) Hook
EI-63
Rear Quarter Trim
EXTERIOR/INTERIOR TRIM
3) Remove the clip, and remove the quarter front
pillar trim.
8) Remove the screws (A) and bolts (B), and remove the quarter lower trim.
(A)
(B)
(A)
(B)
EI-00840
EI-00567
4) Remove the quarter rear pillar trim.
NOTE:
• Remove the screw cover on the tonneau cover
installing part.
• Pull out the shopping bag hook, remove the
screw on back.
B: INSTALLATION
1. SEDAN MODEL
Install in the reverse order of removal.
2. WAGON MODEL
EI-00564
5) Remove the luggage floor box. <Ref. to EI-74,
REMOVAL, Luggage Floor Box.>
6) Remove the luggage floor end cover.
Install in the reverse order of removal.
EI-00570
7) Remove the woofer cover. (Model with McIntosh
Audio)
EI-00622
EI-64
Sun Visor
EXTERIOR/INTERIOR TRIM
27.Sun Visor
A: REMOVAL
1) Remove the cover, loosen the mounting screws,
and remove the sun visor.
EI-00661
2) Disconnect the connector. (Model with vanity
mirror light)
3) Press the (A) on both side using flat tip driver,
pull the sun visor hook and remove it.
(A)
(A)
EI-00662
B: INSTALLATION
Install in the reverse order of removal.
EI-65
Assist Grip
EXTERIOR/INTERIOR TRIM
28.Assist Grip
A: REMOVAL
1) Remove the screw cover, and remove the screw
inside.
2) Pull the left side of assist grip toward you, and rotate the right side of it counterclockwise to remove.
EI-00809
3) Remove the roof trim. <Ref. to EI-67, REMOVAL, Roof Trim.>
4) Remove the bolts, and remove the assist grip
bracket.
EI-00664
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to install the grommet to assist grip
bracket.
When install the assist grip without grommet, it
may cause the faulty returning.
EI-66
Roof Trim
EXTERIOR/INTERIOR TRIM
29.Roof Trim
2. WAGON MODEL
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the spot map light. <Ref. to LI-34, REMOVAL, Spot Map Light.>
3) Remove the room light. <Ref. to LI-35, REMOVAL, Room Light.>
4) Remove the luggage room light. <Ref. to LI-36,
REMOVAL, Luggage Room Light.>
5) Remove the sun visor. <Ref. to EI-65, REMOVAL, Sun Visor.>
6) Remove the assist grip. <Ref. to EI-66, REMOVAL, Assist Grip.>
7) Remove the upper inner trim. <Ref. to EI-62, REMOVAL, Upper Inner Trim.>
8) Remove the rear quarter trim. <Ref. to EI-63,
WAGON MODEL, REMOVAL, Rear Quarter
Trim.>
1. SEDAN MODEL
1) Disconnect the ground cable from battery.
2) Remove the front seats. <Ref. to SE-7, REMOVAL, Front Seat.>
3) Remove the rear seat. <Ref. to SE-14, REMOVAL, Rear Seat.>
4) Remove the console box. <Ref. to EI-53, REMOVAL, Console Box.>
5) Remove the center console. <Ref. to EI-54, REMOVAL, Center Console.>
6) Remove the select lever. (AT model)
<Ref. to CS-7, REMOVAL, Select Lever.>
7) Remove the spot map light. <Ref. to LI-34, REMOVAL, Spot Map Light.>
8) Remove the room light. <Ref. to LI-35, REMOVAL, Room Light.>
9) Remove the sun visor. <Ref. to EI-65, REMOVAL, Sun Visor.>
10) Remove the assist grip. <Ref. to EI-66, REMOVAL, Assist Grip.>
11) Remove the upper inner trim. <Ref. to EI-62,
REMOVAL, Upper Inner Trim.>
12) Remove the rear quarter trim. <Ref. to EI-63,
SEDAN MODEL (MODEL WITH CURTAIN AIRBAG), REMOVAL, Rear Quarter Trim.>
13) Remove the sunroof opening trim. (Model with
sunroof)
CAUTION:
Do not remove the roof end trim with excessive
force. Otherwise roof trim may be damaged.
Roof trim and roof end trim are fastened by rivets.
9) Remove the sunroof opening trim. (Model with
sunroof)
EI-00501
10) Remove the coat hook.
EI-00501
14) Remove the clips and each harness, and remove the roof trim.
15) Pull out the roof trim from vehicle.
EI-00668
11) Remove the clips and each harness, pull out
the rear center seat belt, and remove the roof trim.
EI-00667
EI-67
Roof Trim
EXTERIOR/INTERIOR TRIM
CAUTION:
Do not remove the roof end trim with excessive
force. Otherwise roof trim may be damaged.
EI-00669
B: INSTALLATION
1. SEDAN MODEL
Install in the reverse order of removal.
2. WAGON MODEL
Install in the reverse order of removal.
EI-68
Rear Gate Trim
EXTERIOR/INTERIOR TRIM
30.Rear Gate Trim
5) Remove the clips (A) and (B), remove the rear
gate lower trim.
A: REMOVAL
1) Remove the clips (A), and remove the rear gate
pillar trim.
(B)
(B)
(A)
(A)
EI-00672
6) Remove the rear gate weather strip.
:(A)
EI-00670
2) Remove the clips, and detach the rear gate upper trim.
EI-00673
NOTE:
If the weather strip clip is removed with excessive
force, the weather strip may be damaged. Be sure
to use a clip remover to remove.
EI-00671
3) Remove the cover in the inner handle, loosen
the inside screw.
4) Turn over the weather strip, and remove the
clips.
EB-00141
B: INSTALLATION
Install in the reverse order of removal.
EI-00674
EI-69
Rear Shelf Trim
EXTERIOR/INTERIOR TRIM
31.Rear Shelf Trim
B: INSTALLATION
A: REMOVAL
Install in the reverse order of removal.
1) Disconnect the ground cable from battery.
2) Remove the rear quarter trim. <Ref. to EI-63,
SEDAN MODEL (MODEL WITH CURTAIN AIRBAG), REMOVAL, Rear Quarter Trim.>
3) Remove the high-mounted stop light. <Ref. to LI33, REMOVAL, High-mounted Stop Light.>
4) Remove the rear seat cushion. <Ref. to SE-14,
WAGON MODEL, REMOVAL, Rear Seat.>
5) Remove the lower anchor bolt of rear center seat
belt.
NOTE:
Securely insert the vehicle body panel into the hook
of rear shelf trim center, and then install the rear
shelf trim.
(2)
(1)
(3)
(1) Hook
(2) Rear shelf trim
(3) Vehicle body panel
EI-00675
6) After disconnecting the high-mounted stop light
harness connector (A) and removing the five clips,
remove the rear shelf trim with pulling it frontward.
(A)
EI-00676
EI-70
EI-00739
Trunk Room Trim
EXTERIOR/INTERIOR TRIM
32.Trunk Room Trim
2) Remove the trim clips (A), and remove the trunk
room end cover.
A: REMOVAL
1. TRUNK LID TRIM
1) Remove the trim clips and stopper rubbers, and
remove the trunk lid trim.
(A)
:(B)
EI-00624
(B) Clip
EI-00628
2) Remove the clip (A) of trunk side trim, and then
remove the trunk lid arm cover.
(A)
3) Remove the rear seat backrest, and then remove the trim clips at the front side of trunk side
trim. <Ref. to SE-14, WAGON MODEL, REMOVAL, Rear Seat.>
EI-00625
EI-00629
2. TRUNK ROOM TRIM
1) Remove the trunk room mat.
4) Insert the flat tip driver from the lower side of
trunk hook, and then remove the trunk hook with rotating it 90°.
EI-00841
EI-00623
EI-71
Trunk Room Trim
EXTERIOR/INTERIOR TRIM
5) Remove the trim clips, and remove the trunk
side trim.
EI-00626
B: INSTALLATION
1. TRUNK LID TRIM
Install in the reverse order of removal.
2. TRUNK ROOM TRIM
Install in the reverse order of removal.
EI-72
Floor Mat
EXTERIOR/INTERIOR TRIM
33.Floor Mat
A: REMOVAL
1) Remove the front seats. <Ref. to SE-7, REMOVAL, Front Seat.>
2) Remove the rear seat cushion. <Ref. to SE-14,
REMOVAL, Rear Seat.>
3) Remove the console box. <Ref. to EI-53, Console Box.>
4) Remove the console side panel. <Ref. to EI-54,
REMOVAL, Center Console.>
5) Remove the lower inner trim. <Ref. to EI-60, REMOVAL, Lower Inner Trim.>
6) Remove the footrest. (MT model)
7) Remove the clips from floor mat.
8) Remove the mat hook on both side.
9) Remove the mat from toe board area.
10) Remove the mat from rear heater duct.
11) Roll the mat, and then take it out of opened rear
door.
EI-00677
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
• Secure the mat firmly with hook and clip.
• Insert the mat edge firmly into the groove of side
sill cover.
EI-73
Luggage Floor Box
EXTERIOR/INTERIOR TRIM
34.Luggage Floor Box
A: REMOVAL
1) Remove the luggage floor mat.
2) Remove the clips, and remove the luggage floor
box.
EI-00678
B: INSTALLATION
Install in the reverse order of removal.
EI-74
Trunk Lid Garnish
EXTERIOR/INTERIOR TRIM
35.Trunk Lid Garnish
A: REMOVAL
Remove the license plate, loosen the bolts (A), and
remove the trunk lid garnish.
(A)
EI-00568
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
7.5 N⋅m (0.76 kgf-m, 5.5 ft-lb)
EI-75
Rear Gate Garnish
EXTERIOR/INTERIOR TRIM
36.Rear Gate Garnish
A: REMOVAL
1) Remove the rear gate trim. <Ref. to EI-69, REMOVAL, Rear Gate Trim.>
2) Remove the clip (A), and remove the rear gate
panel side cover.
(A)
EI-00569
3) Remove the hexagon cap nut.
EI-00630
4) Remove the nuts, disconnect each connector,
and remove the rear gate garnish.
EI-00631
B: INSTALLATION
Install in the reverse order of removal.
EI-76
Heat Shield Cover
EXTERIOR/INTERIOR TRIM
37.Heat Shield Cover
A: REMOVAL
1. FRONT HEAT SHIELD COVER
Remove the four bolts to remove front heat shield
cover.
(A)
DI-00211
(A) Transmission mount
2. CENTER HEAT SHIELD COVER
Remove the nut and bolt to remove center heat
shield cover.
EI-00679
3. REAR HEAT SHIELD COVER
1) Remove the muffler. <Ref. to EX(H4SO 2.0)-13,
REMOVAL, Muffler.> <Ref. to EX(H4DOTC)-12,
REMOVAL, Muffler.>
2) Remove the four bolts to remove rear heat shield
cover.
EI-00680
B: INSTALLATION
Install in the reverse order of removal.
EI-77
Ornament
EXTERIOR/INTERIOR TRIM
38.Ornament
A: INSTALLATION
1. LETTER MARK
Adhere the letter mark with following dimension.
• Sedan model
A
(b)
(a)
(1)
B
(2)
(3)
A
(a)
(C)
(2)
A-A
(a)
(1)
Apply the apply tape with aligning
the cut out to the end of trunk lid
garnish.
Letter mark
(b)
(2)
Apply the apply tape with aligning
R stop on the top end of trunk lid
garnish.
Apply tape
EI-78
B-B
EI-00815
(c)
Align the slit of apply tape to panel
end.
(3)
Rear combination light
Ornament
EXTERIOR/INTERIOR TRIM
• Wagon model
(3)
(b)
A
(a)
(2)
(4)
B
A
(C)
(a)
(2)
(1)
A-A
B-B
EI-00816
(a)
(1)
(2)
Apply the apply tape with aligning
the cut out to the end of rear gate
panel.
Letter mark
Apply tape
(b)
(3)
Apply the apply tape with aligning
outer bottom end of rear gate garnish.
Rear gate garnish
(c)
Align the slit of apply tape to panel
end.
(4)
Rear combination light
2. AWD STICKER
Apply the AWD sticker from inside of glass with following dimension.
• Sedan model
(2)
(a)
(1)
(3)
(4)
EI-00741
(a)
(1)
(2)
Apply the apply tape with aligning
the cut out to the end of rear glass
center.
1 mm (0.04 in)
Gradation end of ceramic print
(with rear wiper)
(3)
Gradation end of ceramic print
(without rear wiper)
EI-79
(4)
End of rear glass
Ornament
EXTERIOR/INTERIOR TRIM
• Wagon model (RH side)
(a)
(4)
(2)
(1)
(1)
(b)
(3)
EI-00742
• Wagon model (LH side)
(a)
(4)
(2)
(1)
(1)
(b)
(3)
EI-00743
(a)
(1)
(2)
Apply the apply tape with aligning
the cut out to the ceramic print.
1 mm (0.04 in)
Glass antenna wire
(b)
Gradation end of ceramic print
(3)
Molding
(4)
EI-80
Front side of vehicle
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement