SCT RC5-P60 Series Installation Manual
SCT RC5-P60 Series
The SCT RC5-P60 Series is a high-quality video and control extension system designed to seamlessly connect and control cameras and codecs in professional AV installations.
It supports a wide range of video resolutions, including 4K UHD, and features advanced video processing technologies to ensure pristine image quality over long distances.
The RC5-P60 Series also provides comprehensive control capabilities, allowing users to remotely control cameras from a central location using a variety of control systems, including Cisco TouchPads and other third-party control systems.
Advertisement
Advertisement
at Gui
1 HDMI
1 UTP
1 Power
Power Cont x .
1 3 or Suppl or EI Mi 30’ o
1 2 br BR
W PS30VDC
Power y
2
RC5-P60 Installation Instructions
Supporting the Cisco Precision 60 and
SX80, CodecPlus. and CodecPro Codecs
TEST YOUR LINK CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your LINK cable’s wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1. Test and verify your CAT5e/CAT6 LINK cable for UTP 568A/568B. Link cable must be between 30ft - 300ft.
2. Connect the provided PowerSniffer to the Precision 60 end of your CAT5e/CAT6 Link cable.
3. Connect the other end of the Link cable to the LINK connection on the Head End module.
4. Connect the WPS-12 power supply to the Head End module.
5. Connect the WPS-12 power supply to AC mains.
6. If the SCT Link cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable .
7. Once your cable has been tested, please disconnect the WPS-12 power supply from the Head End module, and the PowerSniffer from the LINK cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1. Connect RCC-C001 video cable between the RC5-CE
Camera End’s HDMI connector labeled “VIDEO INPUT” and the camera’s HDMI connector.
5. Connect the RCC-H016 cable between the Cisco Codec’s
RJ45 Ethernet “Appliance” port and the RC5-HE’s RJ45
Layer 2 Ethernet port labeled ‘Port 1’.
Please Note: ‘Ethernet 2’ supports an additional Precision
60 camera, or if extended, RC5-HE module. Please refer to the visual guide on reverse side of this document.
2. Connect the RCC-C002 control cable between the
RC5-CE’s RJ45 connector labeled “ETHERNET” and the camera’s RJ45 input.
3. Connect the PPC-003 power cable between the RC5-
CE’s power connector labeled “+12V Power” and the camera’s power input.
Connect the codec-end cables:
6. Connect one end of your Cat5e/6 LINK cable to the
RC5-HE module’s “SCT Link” port. Connect the other end to the RC5-CE module’s “SCT Link” port.
7. Connect the WPS-12 power supply to the RC5-HE’s power input labeled “Power +30VDC”.
4. Connect the RCC-H001 cable between the RC5-HE’s
HDMI connector, labeled “VIDEO OUT” and the codec’s
HDMI input.
8. At this point, your camera should have power and video output onto your Cisco TouchPad (or other control system that is correctly connected to your codec).
• ALLOW UP TO TWO MINUTES FOR THE SYSTEM TO INITIALIZE •
MODULE
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
LED LABEL ACTIVE STATUS INACTIVE STATUS
RC5-HE
RC5-HE
HDCP
OK/LINK
Solid Green or Blinking Green Off
Alternating Blinking Red/Green; 1:1 Pattern Blinking Red (occassional single green)
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC5-P60.
DESCRIPTION
RCC-C001
RCC-C002
1’ HDMI Cable
1’ UTP Cable
Video connection between camera and RC5-CE module.
Control connection between camera and RC5-CE module.
PPC-003
RCC-H001
RCC-H016
1’ Power Cable
3’ HDMI Cable
3’ UTP Cable
Power connection between camera and RC5-CE module.
Video connection between codec and RC5-HE module.
Control connection between codec and RC5-HE module.
Power Supply Specifications (AC-Mains Side) Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 30VDC power supply uses 1.45 amperes AC maximum. All specs subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • © SOUND CONTROL TECHNOLOGIES, INC

Public link updated
The public link to your chat has been updated.
Advertisement