Multiscan155f ]I - Manuals, Specs & Warranty

Multiscan155f ]I - Manuals, Specs & Warranty
SONY.
- Operating instructions
. — Mode d'emploi
Trinitron® Color Computer Display
Multiscan15sf I
Multiscan17 sf 1
Manual de instrucciones
CPD-15SF2
MODEL: CPD-1 7SF2
© 1995 by Sony Corporation
a WE
Owner's Record
The mode) and serial numbers are located at the rear of the unit.
Record the serial number in the space provided below. Refer to
these numbers whenever you call upon your dealer regarding this
product.
Model No. CPD- Serial No.
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
Dangerously high voltages are present
inside the set. Do not open the cabinet.
Refer servicing to qualified personnel only.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
¿Mars
(Only for CPD-15SF2)
Bescheinigung des Herstellers
Hiermit wird bescheinigt, daf der Monitor CPD-15SF2 in
Ubereinstimmung mit den Bestimmungen der BMPT-
Amtsblatt Vfg 243/1991, Víg 46/1992 funkentstórt ist.
Der vorschriftsmäßige Betrieb mancher Geräte (z.B.
Meßsender) kann allerdings gewissen Einschränkungen
unterliegen. Beachten Sie deshalb die Hinweise in der
Bedienungsanleitung. Dem Bundesamt für Zulassungen in der
Telekommunikation wurde das Inverkehrbringen dieses
Gerätes angezeigt und die Berechtigung zur Überprüfung der
Serie auf Einhaltung der Bestimmungen eingeräumt.
Sony Deutschland GmbH
Hugo Eckener Str. 20 50829 Köln
Hinweis
Gemäß der Amtsblätter des BMPT Nrn. 61/1991 und 6/1992
wird der Betreiber darauf aufmerksam gemacht, daß die von
ihm mit diesem Gerät zusammengestellte Anlage auch den
technischen Bestimmungen dieser Amtsblätter genügen muß.
Hinweise
e Aus ergonomischen Gründen wird empfohlen, die
Grundfarbe Blau nicht auf dunklem Untergrund zu
verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu
geringem Zeichenkontrast).
e Aus ergonomischen Gründen flimmern sollten nur
Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne
Zeilensprung) benutzt werden.
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte toutes les
exigences du Reglement sur le materiel brouilleur du Canada.
INFORMATION -
This product complies with Swedish National Council fo
Metrology (MPR) standards issued in December 1990 (MPR II) for
very low frequency (VLF) and extremely low frequency (ELF).
INFORMATION
Ce produit est conforme aux normes du Swedish National Council
for Metrology de décembre 1990 (MPR II) en ce qui concerne les
fréquences tres basses (VLF) et extrémement basses (ELF).
Hinweis
Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency)
und tiefstfrequenter (extremely low frequency) Strahlung die
Vorschriften des „Swedish National Council for Metrology (MPR)“
vom Dezember 1990 (MPR 11).
INFORMACIÖN
Este producto cumple las normas del Consejo Nacional Sueco para
Metrologia (MPR) emitidas en diciembre de 1990 (MPR II) para
frecuencias muy bajas (VLF) y frecuencias extremadamente bajas
(ELF).
NOTICE
This notice is applicable for USA /Canada only.
If shipped to USA/Canada, install only a UL LISTED /CSA
LABELLED power supply cord meeting the following
specifications:
SPECIFICATIONS
Plug Type Nema-Plug 5-15p
Cord Type SVT or SIT, minimum 3 x 18
AWG
Length Maximum 15 feet
Rating Minimum 7 A, 125 V
NOTICE
Cette notice s'applique aux Etats-Unis et au Canada
uniquement.
Si cet appareil est exporté aux Etats-Unis ou au Canada, utiliser
le cordon d'alimentation portant la mention UL LISTED/CSA
LABELLED et remplissant les conditions suivantes:
SPECIFICATIONS _
Type de fiche Fiche Nema 5-15 broches
Cordon “ TypeSVTouSJT, minimum 3 x 18
AWG
Longueur Maximum 15 pieds
Tension Minimum 7 A, 125 V
E > arm
This monitor is Energy Star
Compliant when used with a
computer equipped with VESA
Display Power Management
2997 Signaling (DPMS). The Energy Star
emblem does not represent EPA
EPA POLLUTION PREVENTER endorsement of any product or
service.
7
Nu
Introduction
Table of Contents
IntroductiON ararrrer 3
Precautions een nee canina nene nao nece 3
Getting Started ………….…..….…rresianenennenenenennnnnnnnnnnnnn 4
Using Your Monitor o.oo, 4
AJUSTIMENES oor 5
Entering New Timings.................. eee 7
Power Saving FunctiON a4... re 7
Plug and Play ee, 8
Use of the Tilt-Swivel ..................=m...... enn e 8
Damper Wire es es encerancescessrcersennens 8
SPeCIHICAtIONS Lo... Ns 8 |
Troubleshooting een eee ee |
Congratulations on vour purchase of a Sonv Multiscan
1>sfll/17sfII! |
This monitor incorporates over 25 vears ot Sonv experience
with Trinitron display technologv, ensuring excellent
performance and outstanding reliability. The Multiscan
15s£l1/17sfll’s wide scan range (31 - 65 kHz), together with
Digital Multiscan Technology, allows it to svnc to any video
mode from standard VGA through 1024 x 768 at 76 Hz
(1280 x 1024 at 60 Hz).
Precautions
In addition, its two factory preset color modes and one user
adjustable color mode give you unprecedented flexibility in
matching on-screen colors to hard copy printouts.
Furthermore, the Multiscan 15sf[1/17sfIl feature digital
controls, raster rotation, power saving, low emissions, and
much more. All together, it delivers incredible performance
with the quality and support you can expect from Sony.
Installation
Prevent internal heat build-up bv allowing adequate air
circulation. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials icurtains, draperies) that
mav block the ventilation holes.
e Do not install the unit near heat sources such as radiators
or air ducts, nor in a place subject to direct sunlight,
excessive dust, mechanical vibration or shock.
e Do not place the unit near equipment which generates
magnetism, such as a converter or high voltage power
lines.
Warning on Power Connection
e Use the supplied power cord.
For the customers in U.S.A.
lf vou do not do this, this monitor will not conform to
mandatory FCC standards.
for 100 to 120 V AC for 220 to 240 V AC
=
Maintenance
e Clean the cabinet, glass panel and controls with a soft
cloth lightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent, such as alcohol or benzine.
* Do not rub, touch, or tap the surface of the screen with
sharp or abrasive items, like a ball point pen or a screw
driver. Otherwise, this type of contact may result in a
scratched picture tube.
e Before disconnecting the power cord, wait for at least
30 seconds after turning off the power switch to allow for
the discharging of static electricity on the CRT display
surface. .
e After the power has been turned on, the CRT is
demagnetized for approximately 5 seconds. This generates
a strong magnetic field around the bezel which mav affect
the data stored on magnetic tape or disks near the bezel.
Place such magnetic recording equipment and tapes/disks
at a distance from this unit.
The socket-outlet shall be installed near the equipment
and shall be easily accessible.
Getting Started
Before using this monitor, please make sure that the
following items are included in vour package: Multiscan
15sf11/17sfIl monitor (1), power cord (1), warranty card (1)
and this operating instruction manual (1).
This monitor will svne with anv IBM or compatible svstem
equipped with VGA or greater graphics capability.
Although this monitor will svnc to other platforms running
at horizontal frequencies between 31 and 65 kHz, including
Macintosh and Power Macintosh system, a cable adaptor is
required. Please consult vour dealer for advice on which
adaptor is suitable for vour needs.
Step 1: With the monitor switched oft, attach the power
cord to the monitor and the other end to a power
outlet.
Power cord (supplied)
AA N
to a power outlet L£7— DD
ГОД
— E
With the computer switched off, attach the video
signal cable to the video output.
Step 2:
Using Your Monitor
Preset and User Modes
The Multiscan 15sfll/17sfII has tactorv preset modes for the
6 most popular industry standards for true “plug and play”
capability.
For less common modes, the Multiscan 1551/1755
Digital Multiscan Technology will perform all of the
complex adjustments necessary to ensure a high quality
picture for anv timing between 31 and 65 kHz.
IBM or compatible computer
| to video output
pres
|| E“
FR
UL)
r= V
5 |
|
|
|
Apple computer
—
ооо +3
Macintosh Adapter
(sold separately)
to video output
Step3: Turn on the monitor and computer.
Step 4: If necessary, adjust the user controls according to
your personal preference.
The installation of vour Multiscan 15sfl1/17sfIl is complete.
Enjoy your monitor.
| No. | Resolution | Horizontal Vertical Graphics
(dots x lines: | Frequency | Frequency | Mode
1 ¡640x480 (131.5 КНг |60 Hz VGA Graphic "
2 1800 x 600 46.9 kHz |75 Hz VESA -
3 1800x600 153.7 kHz |85 Hz VESA =
4 1832x624 1497 kHz |75 Hz Macintosh
| 167 Color
> 11024 x 7658 160.0 kHz |75 Hz VESA =
6 11280 x 1024 164.0 kHz 160 Hz VESA -
Note: For Windows* * users, check vour video board
manual or the utility program which comes with
your graphic board and se:ect the highest available
refresh rate to maximize monitor performance.
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 psec.
Horizontal blanking width should be: >3.6 psec.
1) VGA is a trademark of IBM Corporation.
2) VESA is a trademark of the non-profit organization,
Video Electronics Standard Association.
3) Macintosh is a trademark of Apple Computer Inc.
4) Windows® is a registered trademark of Microsoft
Corporation in the United States and other countries.
Adjustments
When one of the preset-type signals is input, no picture
adjustment is necessary.
You can, however, adjust the picture to vour preferences by
tollowing the procedure described below.
You can adjust the all items on the OSD (On Screen
Displav).
Control Panel
# Before adjusting the items, turn on the unit and feed the
video signal from the connected computer/work
station.
M When the limit value is reached, the POWER SAVING
indicator will begin to flash.
B Adjustments will be stored automatically.
© Се) ED о о (©)
O “CO DJ CDD ес с СЯ
RESET соя GEOM SIZE > POWER
Adjusting the Picture Brightness
The adjustment data becomes
input signal.
the common setting for all
1 Press the O- <= /wb button.
The “CONTRAST /BRIGHTNESS” OSD appears.
ECSIO CS)
0
CONTRAST/BRIGHTNESS
31.5kHz/7OHz
2 Press the C- <=/=» buttons to adjust picture brightness.
<=... for less brightness”
=> ... for more brightness
The “CONTRAST/BRIGHTNESS” OSD disappears 2
seconds after you release the buttons.
Adjusting the Picture Contrast
The adjustment data becomes
input signal.
1 Press the 9 4/4 button.
The “CONTRAST/BRIGH
the common setting for all
TNESS” OSD appears.
ED
O
<=
O
“
CONTRAST/BRIGHTN ESS
\.
EN aaa —— |)
# 100 ® + 50 >
31.5kH2/70HzZ
2 Pressthe Y 4/4 buttons to adjust picture contrast.
+... Рог тоге contrast
$ ...for less contrast
The “CONTRAST/BRIGHTNESS” OSD disappears ?
seconds after vou release the buttons.
Adjusting the Picture Centering
The adjustment data becomes the unique setting for the
input signal received.
1 Press the CENTER button.
The “CENTER” OSD appears.
CENTER
CENTER
a 32 + « 68 =
2 For vertical adjustment
Press the 9 À ‘$ buttons.
Ca)
О,
FI
=
$ ...tomorve up
$ ...to move down
For holizontal adjustment
Press the C «m / => buttons.
э Се о С
yoy
vol
om
to move left
=> to move right
To erase the “CENTER” OSD, press the CENTER button
again.
The “CENTER” OSD automatically disappears 20 seconds
after vou release the buttons.
Adjustments
Adjusting the Picture Size
The adjustment data becomes the unique setting for the
input signal received.
1 Press the SIZE button.
The “SIZE” OSD appears.
SIZE
SIZE
ma] mm
№ 32 © № 68 №
2 For vertical adjustment
Press the 0 4/4 buttons.
с
О
D
D
f ... to enlarge
4 ... to diminish
For holizontal adjustment
Press the O: <=/ => buttons.
9 CS) O C2)
o
=... to diminish
=>... to enlarge
To erase the “SIZE” OSD, press the SIZE button again.
The “SIZE” OSD automatically disappears 20 seconds after
you release the buttons.
Adjusting the Picture Rotation
The adjustment data becomes the common setting for all
input signal.
1 Press the GEOM button.
The “GEOMETRY” OSD appears.
GEOMETRY
GEOM
№ 32 № + 68 >
À Press the 0 4/4 buttons.
$ .. .torotate clockwise
$ ...torotate counterclockwise
Co
O
PO
Q
To erase the “GEOMETRY” OSD, press the GEOM button
again. |
The “GEOMETRY” OSD automatically disappears 20
seconds after you release the buttons.
Adjusting the Pincushion
The adjustment data becomes the unique setting for the
input signal received.
1 Press the GEOM button.
The “GEOMETRY” OSD appears.
GEOMETRY
GEOM
2 Press the OO: «=/ > buttons.
© Се ©
0
<= .. . to diminish the picture sides
=p . .. to expand the picture sides
ро
To erase the “GEOMETRY” OSD, press the GEOM button
again. -
The “GEOMETR Y” OSD automatically disappears 20
seconds after you release the buttons.
Setteing the color temperature
The selected color temperature becomes the common setting
for all input signals.
1 Press COLOR button.
The “COLOR TEMPERATURE” OSD appears.
COLOR TEMPERATURE
COLOR VARIABLE
NS! 5000K 9300K
+ 50 + © =
2 ATjust with the O: =/> and 9 4/4 buttons.
To select 5000K or 9300K
Press O- <=/ > buttons.
The selected color temperature is indicated in yellow.
9 CS) O Ce)
y
<= to select 5000K
=p» to select 9300K
To obtain the desired color temperature between 5000K
and 9300K
Press 9 4/4 buttons.
Ca)
O
PO
D
$ ...for higher temperature
$... tor lower temperature
Your most recent adjusted color temperature will be
recalled by pressing 9 4/4 button.
To erase the “COLOR TEMPERATURE” OSD, press the
COLOR button again.
The “COLOR TEMPERATURE” OSD automatically
disappears 20 seconds after vou release the buttons.
Resetting
e Press the RESET button to recall the factory settings for
brightness, contrast, horizontal and vertical size, center
"and pincushion for the mode currently in use.
e Press and hold the RESET button for 2 seconds to recall
factorv setting for all adjustments in all modes.
RESET
Entering New Timings
When using a video mode that is not one of the 6 factory
preset modes, some fine tuning may be required to optimize
the display to vour preferences. Simply adjust the monitor
according to the preceding adjustment instructions. The
adjustments will be stored automatically and recalled
whenever that mode is used.
A total ot 10 user-defined modes can be stored in memory.
If the 11th mode is entered, it will replace the first.
Power Saving Function
This monitor meets the power saving guidelines set by the
EPA Energy Star Program as well as the more stringent
NUTEK 803299 (TCO92) guidelines. It is capable of reduced
power consumption when used with a computer equipped
with Display Power Management Signaling (DPMS). By
sensing the absence of the sync signal coming from the
computer, it will reduce the power consumption as follows:
CAUTION: The Power Saving function will automatically
put the monitor into Active-off state if the power
switch is turned on without any video signal
input. Once the horizontal and vertical syncs are
sensed, the monitor will automatically return to
its Normal operation state.
Power Required ©) Power POWER
State . {resumption |.” .. SAVING
consumption indicator | ©.
time indicator
1 Normal 100% — green on off
operation
Suspend approx approx
3 st step of > n eo
2 (st ep of 10% 3 sec. green 0 orang n
pow er sar Ing)
-15SF2.
Active-off py
nd: € | approx. .
>| (end step Oo” | Cpp.17SF2:| 10sec. | ff | orange on
power saving) с
| approx. 6%
Plug and Play
This monitor complies with the DDC1™" and DDC2B™"
which are the Display Data Channel (DDC) standards of
VESA.
When a DDC1 host system is connected, the monitor
svenchronizes with the V. CLK in accordance with the
VESA standards and outputs the EDID (Extended Displav
Indentification) to the data line.
When a DDC2B host system is connected, the monitor
automatically switches to the DDC2B communication.
= DDC™ is a trade mark of the non-profit organization, Video
Electronics Satandard Association.
Use of the Tilt-Swivel
With the tilt-swivel, this unit can be adjusted to be viewed at
vour desired angle within 90° horizontally and 20° vertically.
To turn the unit vertically and horizontally, hold it at its
bottom with both hands.
Damper Wire
Using a white background, very thin horizontal stripes on
the screen are visible as shown on the illustration. These
stripes are damper wires. These wires are attached to the
aperture grille inside the Trinitron tube and are there to
damp vibrations of the aperture grille in order to prevent
them from influencing to the picture quality.
Damper wire
A
a Д ¡ Approx. 6 cm
eo / | (Multiscan
р v 17sfII only)
a A
\_ { Approx. 6 cm
Specifications
CPD-15SF2
Picture tube
Video image area
Logical resolution
Physical resolution
Standard image area
Deflection frequency
0.25 mm aperture grille pitch
15 inches measured diagonally (14”
maximum viewing image) 90-degree
deflection
Approx. 285 x 213 mm (w/h)
(111/4x 8 1/2 inches)
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Horizontal: Max. 1024 dots
Vertical: Max. 768 lines
Approx. 270 x 202 mm (w/h)
(10 3/4 x 8 inches)
Horizontal: 31 to 65 kHz
Vertical: 50 to 120 Hz
AC input voltage/current
100 to 120 V, 50/60 Hz, 1.8 A
220 to 240 V, 50 - 60 Hz, 1 А
Dimensions Approx. 368 x 373 x 384.5 mm (w/h/d)
(14 1/2 x 14 3/4 x 15 1/4 inches)
Mass Approx. 13.6 kg (30 Ib 7 0z)
CPD-17SF2
Picture tube 0.25 mm aperture grille pitch
Video image area
Logical resolution
Physical resolution
Standard image area
Deflection frequency
17 inches measured diagonally (16”
maximum viewing image) 90-degree
deflection
Approx. 328 x 242 mm (w/h)
(13 x 9 5/8 inches)
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Horizontal: max. 1280 dots
Vertical: Max. 1024 lines
Approx. 300 x 225 mm (w/h)
(11 7/8 x 8 7/8 inches)
Horizontal: 31 to 65 kHz
Vertical: 50 to 120 Hz
AC input voltage /current
Dimensions
Mass
100 to 120 V, 50/60 Hz, 1.8 A
220 to 240 V, 50-60 Hz, 1 A
Approx. 406 x 426.5 x 451 mm (w/h/d)
(16 x 16 7/8 x 17 7/8 inches) |
Approx. 19.0 kg (41 1b 14 07)
Design and specifications are subject to change without
notice.
Troubleshooting
This section may help you isolate a problem and as a result,
eliminate the need to contact technical support, allowing
continued productivity.
No picture
=> If neither the O (power) indicator nor the
POWER SAVING indicator is lit
— Check that the power cord is properly
connected. |
— Check that the power switch is in the “ON”
position.
=p If the POWER SAVING indicator is lit
— Check that vour computer power switch is
in the “ON” position.
— The monitor will recover when you press
any key on the keyboard.
— Check that the video cable is properly
connected.
— Ensure that no pins are bent or pushed in
the HD15 connector of the cable.
— Check that the video card is seated
completely in a proper bus slot.
— Check that the video sync signal is within
that specified for the monitor.
— If using a Mac system, check that a proper
HD15-D15 adaptor is provided to work
correctly with your Mac.
=> If the O (power) and the POWER SAVING
indicators are both flashing
— There is a potential monitor failure.
Contact your dealer.
If the message of "OUT OF SCAN RANGE" appears on
the screen
=> Check that the video svnc signal is specified
for the monitor.
Picture is scrambled
=> Check your graphics board manual for the
proper monitor setting on your Multiscan
15sfl1/17sfll.
= Check this manual and confirm that the ~
graphic mode and the frequency at which you
are trying to operate is supported. Even
within the proper range some video boards
may have a sync pulse that is too narrow for
the monitor to svnc correctly.
Color is not uniform
=p Trip the power switch once to activate the
Auto-degauss cvcle*.
Screen image is not centered or sized properly
=» Adjust the “CENTER”, “SIZE”, or
“GEOMETRY” on the OSD (page 5, 6).
=p» Some video modes do not fill the screen to the
edge of the monitor. There is no single answer
to solve the problem. There is a tendency to
have this probiem on higher refresh timings
and Macintosh video timings.
Picture is fuzzy
=» Adjust the “CONTRAST” and
“BRIGHTNESS” on the OSD (page 5). We
have come across several brands of SVGA
boards that have an excessive video output
level which creates a fuzzy picture at max
contrast.
=» Trip the power switch once to activate the
Auto-degauss cycle*.
Picture bounces or has wavy oscillations
=p Isolate and eliminate any potential sources of
electric or magnetic fields. Common causes for
this symptom are electric fans, fluorescent
. lighting, laser printers, and so on.
=> If vou have another monitor close to this
monitor, increase the distance between them
to reduce the interference.
=p Try plugging the monitor into a different AC
outlet, preferably on a different circuit.
= Try the monitor on a completely different
computer in a differnt room.
Picture appears to be ghosting
=} Eliminate the use of video cable extension
cables and/or video switch boxes if this
svmptom occurs. Excessive cable length or
weak connections can procude this symptom.
A fine horizontal line (wire) is visible
=> This wire stabilizes the vertically striped
Aperture Grille. This Aperture Grille allows
more light to pass through to the screen giving
the Trinitron CRT more color and brightness.
Wavy or elliptical (moire) pattern is visible
=» Due to the relationship between resolution,
monitor dot pitch and the pitch of some image
patterns, certain screen backgrounds,
especially gray, sometimes show moire. This
can only be eliminated by changing your
desktop pattern.
*The Auto-degauss function demagnetizes the metal
frame of the CRT to obtain a neutral field for uniform
color reproduction. If a second degauss cycle is needed,
allow a minimum interval of 20 minutes for the best
result.
* [f the problem persists, call your authorized Sony dealer
from a location near your monitor.
e Note the model name and the serial number of your
monitor. Also note the make and name of your computer
and video board. :
A AW
SONY :
Important Safeguards
For your protection, please read these instructions completely,
and keep this manual for future reference.
Carefully observe and comply with all warnings, cautions and instructions
placed on the set, or described in the operating instructions or service manual.
| WARNING |
To guard against injury, the following basic safety precautions should be
observed in the installation, use, and servicing of the set.
_— - Sony Corporation Printed in Japan «+1988
4-491-213-26 (1)
Wega md he at te smn
ar “— E dE EE
Use
Power Sources — This set should be
operated only from the type of power
source indicated on the serial/mode! plate.
if you are not sure of the type of electrical
power supplied to your home, consult your
A] dealer or local power company. For those
sets designed to operate from battery
power, refer to the operaling instructions.
Grounding or Polarization — This set is
Always turn the set off when it is not to
be used. When the set is left unattended
and unused for long periods of time,
unplug it from the wall outlet as a
precaution against the possibility of an
internal maifunction that could create a
fire hazard.
* м » Object and Liquid Entry — Never push
equipped with a polarized ac power cord e objects of any kind into the set through
plug (a plug having one blade wider than A the cabinet slots as they may touch
the other), or with a three-wire grounding as dangerous voltage points or short out
type plug (a plug having a third pin for parts that could result in a fire or electric
grounding). Follow the instructions below: shock. Never spill liquid of any kind on the
| set.
-For the set with a polarized ac power LE
cord plug: .
This plug will fit into the power outlet only
one way. This is a safety feature. if you
are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug
should still fail to fit, contact your
electrician to have a suitable outlet
installed. Do not defeat the safety purpose
of the polarized plug by forcing it in.
Alternate Warning — For the set with a
three-wire grounding type ac plug:
This plug will only fit into a grounding-type
power outlet. This is a safety feature. If
you are unable to insert the plug into the
outlet, contact your electrician to have a
suitable outlet instatied. Do not defeat the
safety purpose of the grounding plug.
Overloading — Do not overload wall
outlets, extension cords or convenience
receptacles beyond their capacity, since
this can result in tire or electric shock.
Attachments — Do not use attachments
not recommended by the manufacturer, as
they may cause hazards.
Cleaning — Unplug the set from the wall
outlet before cleaning or polishing it. Do
not use liquid cleaners or aerosol cleaners.
Use a cloth lightly dampened with water
for cleaning the exterior of the set .
If a snapping or popping sound from a TV
set is continuous or frequent while the TV
is operating, unplug the TV and consult
your dealer or service technician. It is
normal for some TV sets to make
occasional snapping or popping sounds,
particularly when being turned on or off.
installation
Water and Moisture — Do not use power-
line operated sets near water—for
example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, etc.
Ventilation — The slots and openings in
the cabinet and in the back or bottom are
provided for necessary ventilation. To
4 Accessories — Do not place the set on an
unstable cart, stand, table or shelf. The set
may fall, causing serious injury to a child
or an adult, and serious damage to the
set. Use only a cart or stand
recommended by the manufacturer.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination
to overturn.
-Never place the set in a confined space,
such as a bookcase, or built-in cabinet,
unless proper ventilation is provided.
ensure reliable operation of the set, and to
protect it from overheating, these slots
and openings must never be blocked or
covered.
-Never cover the slots and openings with a
cloth or other materials.
Do not place the set near or over a
radiator or heat register, or where it is
exposed to direct sunlight.
-Never block the slots and openings by
placing the set on a bed, sofa, rug or
other similar surface.
Power-Cord Protection — Do not allow
anything to rest on.or roll over the power
cord, and do not place the set where the
power cord is subject to wear or abuse.
Antennas
Ourdoor Antenna Grounding — If an outdoor antenna is installed, Antenna Grounding According to the National Electrical Code
follow the precautions below.
An outdoor antenna system should not be tocated in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME
CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH
POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST
INVARIABLY FATAL
Antenna lead-in wire
Antenna discharge unit
(NEC Section 810-20)
Ground clamp
Be sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges. Section
810 of the National Electrical Code provides information with respect
to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
Grounding conductors
(NEC Section 810-21)
Ground clamps
Electric service
equipment
«—— Power service grounding
electrode system
(NEC Art250 Part H)
NEC-Nationa! Electrical Code
Lightning — For added protection for this television receiver during
a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect
the antenna. This will prevent damage to the receiver due to
lightning and power-line surges.
=
FRATAD ON TAUI
AC E
CRACIED PLUG
Damage Requiring Service —Unplug the
set from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
‘When the power cord or plug is damaged
or frayed.
-If liquid has been spilled into the set.
-1f the set has been exposed to rain or
water.
«If the set has been subject to excessive
shock by being dropped, or the cabinet
has been damaged.
-If the set does not operate normally when
following the operating instructions. Adjust
only those controis that are specified in
the operating instructions. Improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore
the set to normal operation.
-When the set exhibits a distinct change in
performance —this indicates a need for
service.
[ TV SERVICE E
oy [rl |
OUR UK
[Ei
ALL SETS RECENE
SAFETY CHECK
Servicing — Do not attempt to service the
sel yourself since opening the cabinet may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified
service personnel,
Replacement Parts — When replacement
parts are required, be sure the service
technician certifies in writing that he has
used replacement parts specified by the
manufacturer that have the same
characteristics as the original parts.
Unauthorized substitutions may result in
fire, electric shock, or other hazards.
Safety Check — Upon completion of any
service or repairs to the set, ask the
service technician to perform routine
safety checks (as specified by the
manufacturer) to determine that the set is
in safe operating condition, and to so
certify.
When the set reaches the end of its useful
life, improper disposal could result in a
picture tube implosion. Ask a qualified
service technician to dispose of the set.
SONY © REFURBISHED
Computer Peripheral Products
LIMITED WARRANTY
SONY CORPORATION OF AMERICA (“Sony”) warrants this Product against defects in material or workmanship as follows:
For a period of ninety (90) days from the date of purchase, Sony will at its option either replace the product at no cost to you with
a new or rebuilt unit or pay the labor charges and provide new or rebuilt replacement parts during the same ninety (90) day
period for any repair work performed at any authorized Sony service facility. In addition, Sony will provide, at no charge, a parts
replacement for a defective Color Picture Tube only for a period of ninety (90) days from the date of purchase.
To obtain warranty service you must take the product or deliver the product freight prepaid to the designated Sony Authorized
Service Facility.
This warranty does not cover any units which have been previously altered, repaired or serviced by anyone other than a service
facility authorized by Sony, a unit on which the serial number has been altered or removed or a unit which has been subject to
accident, misuse, or abuse.
This warranty is valid only in the United States.
You must retain the dated bill of sale as evidence of the date of purchase.
This warranty is valid only if the serial number appears on the product.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PUR-
CHASER. SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
HEREBY DISCLAIMED. > -
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state.
In addition, if you enter into a service contract with the Sony Partnership, Within ninety (90) days of the date of sale, the
limitation on how long an implied warranty lasts does not apply to you.
For your convenience, SONY CORPORATION OF AMERICA has established the Customer Information Center to supply you
with product or service information including the name of your nearest designated Sony Authorized Service Facility.
SONY CUSTOMER TECHNICAL SUPPORT
800 - 326 - 9551 —
or write to:
SONY TECHNICAL SUPPORT
Mail Drop SJ-3A1
3300 Zanker Road
San Jose, CA 95134 1940
For the location of your nearest Sony Authorized Service Facility please call the following number:
SONY AUTHORIZED SERVICE LOCATIONS
800 -342 - 5721
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement