Mindray Panorama User manual
Service Manual
Panorama®
Pat i e n t m o n i to r i n g n e t w o r k
0070-01-0656-01_revD.indd 1
9/30/11 10:32 AM
Service Manual
Panorama® C E N T R A L S TAT I O N
PAT I E N T M O N I TO R I N G N E T W O R K
0070-02-0656-01_revD.indd 1
9/30/11 10:29 AM
DPMTM is a trademark of Mindray DS USA, Inc.
e-GatewayTM is a trademark of Mindray DS USA, Inc.
GatewayTM is a trademark of Mindray DS USA, Inc.
HP® is a registered trademark of Hewlett Packard Company.
Microsoft®, Windows®, and Windows NT® are US registered trademarks of Microsoft Corporation.
Mindray® is a trademark of Shenzhen Mindray Bio-Medical Electronics Co., Ltd.
Panorama® is a U.S. trademark of Mindray DS USA, Inc.
Passport® is a U.S. registered trademark of Mindray DS USA, Inc.
Passport2® is a U.S. registered trademark of Mindray DS USA, Inc.
PassportV® is a U.S. registered trademark of Mindray DS USA, Inc
Spectrum® is a U.S. registered trademark of Mindray DS USA, Inc.
Spectrum OR TM is a U.S. trademark of Mindray DS USA, Inc
V SeriesTM is a U.S. registered trademark of Mindray DS USA, Inc.
Copyright © Mindray DS USA, Inc., 2015 All rights reserved. Contents of this publication may not be
reproduced in any form without permission of Mindray DS USA, Inc.
Panorama™ Service Manual
This page intentionally left blank.
Panorama™ Service Manual
Foreword ........................................................................................................................................ iv
Warnings, Cautions, and Notes ...................................................................................................... iv
Warnings ........................................................................................................................................ iv
Cautions ........................................................................................................................................ vi
How to Get Help ............................................................................................................................. vii
Phone Numbers and How to Get Assistance… .............................................................................. vii
Manufacturer's Responsibility ........................................................................................................ vii
Instrument Description ................................................................................................................ 1 - 1
Introduction ............................................................................................................................... 1 - 2
Overview ........................................................................................................................... 1 - 2
Panorama telemetry .................................................................................................................. 1 - 2
Core Functions and Components ...................................................................................... 1 - 3
Panorama Block Diagram .................................................................................................. 1 - 4
System Modules, Components, and Peripherals ....................................................................... 1 - 5
Panorama Central Station ................................................................................................. 1 - 5
Network Laser Printer........................................................................................................ 1 - 5
Keyboard, Video, and Mouse (KVM) Extender .................................................................. 1 - 5
Network Ethernet Switches ............................................................................................... 1 - 5
Uninterruptible Power Supply (UPS) ................................................................................. 1 - 5
Access Point (optional 2.4 GHz Telemetry only) ............................................................... 1 - 6
Bedside Monitors .............................................................................................................. 1 - 6
ViewStation(Optional) ....................................................................................................... 1 - 6
WorkStation (Optional) ...................................................................................................... 1 - 9
Gateway/e-Gateway (Optional) ......................................................................................... 1 - 9
Telemetry Server (Optional) .............................................................................................. 1 - 9
Wireless Transceiver (Optional) ........................................................................................ 1 - 9
Theory of Operation .................................................................................................................. 1 - 9
Panorama Central Station and Wireless Telemetry Server ................................................ 1 - 9
Motherboard ............................................................................................................. 1 - 9
Connected to the Motherboard via PCI connectors: ................................................... 1 - 10
Connected to the Riser Card (optional) ..................................................................... 1 - 10
System Hard Drive Assembly ................................................................................... 1 - 10
CD-ROM Drive .......................................................................................................... 1 - 10
Patient Network Interface Card ................................................................................. 1 - 10
AGP Graphics Display Card (if applicable) ................................................................ 1 - 10
ATX Power Supply .................................................................................................... 1 - 10
Disclosure Hard Drives (Central Stations, WorkStations and Gateways Only) ........... 1 - 10
3.5” Floppy Drive (optional) ...................................................................................... 1 - 10
Clock Card (optional) ................................................................................................. 1 - 11
Central Station Displays ................................................................................................... 1 - 11
LCD Display .............................................................................................................. 1 - 11
Audio ......................................................................................................................... 1 - 11
Panorama™ Service Manual
i
Repair Information ....................................................................................................................... 2 - 1
Introduction ............................................................................................................................. 2 - 2
Safety Precautions ................................................................................................................. 2 - 2
Equipment and Special Tools Required .................................................................................. 2 - 2
Troubleshooting ...................................................................................................................... 2 - 3
Central Station, Display Monitors and Laser Printers ........................................................ 2 - 3
Communication Loss from an Individual Bedside Monitor ................................................. 2 - 5
Communication Loss from All hardwired Bedside Monitors .............................................. 2 - 9
Communication Loss from All 2.4GHz Bedside Monitors................................................... 2 - 9
Communication Loss from WMTS Devices Telemetry Devices ......................................... 2 - 11
Panorama Wireless Telemetry Server ............................................................................... 2 - 13
Disassembly Instructions ........................................................................................................ 2 - 14
Assembly Diagrams ........................................................................................................... 2 - 14
Disassembly Instructions .................................................................................................. 2 - 15
0998-00-0206-10 Telemetry Server Chassis ................................................................ 2 - 18
0998-00-0700-01 Central Station Chassis ................................................................... 2 - 20
0998-00-0705-01 Central Station Chassis ................................................................... 2 - 22
0998-00-0708-01 Central Station Chassis ................................................................... 2 - 23
0998-00-0708-03 Central Station Chassis ................................................................... 2 - 23
0998-00-0709-01 Central Station Chassis ................................................................... 2 - 26
0998-00-0709-03 Central Station Chassis .................................................................... 2 - 28
0998-00-0710-01 Telemetry Server Chassis ................................................................ 2 - 28
0998-00-0190-02 Wireless Transceiver ........................................................................ 2 - 30
Parts Replacement ....................................................................................................................... 3 – 1
Introduction .............................................................................................................................. 3 - 2
Available Replacement Parts and Assemblies ........................................................................ 3 - 2
Product Variations ................................................................................................................... 3 - 2
Parts Pricing Information ........................................................................................................ 3 - 2
Ordering Information ............................................................................................................... 3 - 2
Description and part number .................................................................................................... 3 - 3
Calibration ................................................................................................................................... 4 - 1
Preventative Maintenance ........................................................................................................... 5 - 1
Display Monitors ...................................................................................................................... 5 - 2
LCD Display Chassis ......................................................................................................... 5 - 2
Care and Cleaning of the Screen/Touchscreen ................................................................. 5 - 2
Central Station, Gateways, Telemetry Server and Wireless Transceiver ................................. 5 - 3
Cleaning ........................................................................................................................... 5 - 3
Visual Inspection .............................................................................................................. 5 - 3
Uninterruptible Power Supplies (UPS) ..................................................................................... 5 - 3
Rack Mounted UPS ........................................................................................................... 5 - 3
Desktop and Auxiliary UPS ............................................................................................... 5 - 3
Central Station Network Equipment Racks .............................................................................. 5 - 4
System Maintenance Schedule ................................................................................................ 5 - 4
Preventative/Periodic Maintenance ................................................................................... 5 - 4
ii
Panorama™ Service Manual
Equipment Configuration ............................................................................................................ 6 - 1
Introduction .............................................................................................................................. 6 - 2
Configuring the Telemetry Server ...................................................................................... 6 - 2
Wired Bedside Monitor Communication Configuration ...................................................... 6 - 3
Passport2 and Spectrum WMTS configuration .................................................................. 6 - 7
Mindray 2.4 GHz monitor configuration ............................................................................. 6 - 8
Appendix A .................................................................................................................................. 7 - 1
Panorama Motherboard CMOS Setup/Verification ................................................................... 7 - 2
Central Station ViewStation WorkStation (0998-00-0701-01, 0998-00-0705-01) .............. 7 - 3
2U Telemetry Server (0998-00-0206-10) .......................................................................... 7 - 5
RM/VM Central Station, ViewStation, WorkStation and Gateway (0998-00- 0708-01,
0998-00-0709-01) ............................................................................................................. 7 - 9
Telemetry Server (0998-00-0710-01) ............................................................................... 7 - 13
e-Gateway 0998-00-0708-03, 0998-00-0709-03 ............................................................... 7 - 16
Appendix B .................................................................................................................................. 8 - 1
Programming & configuring replacement Panorama telemetry devices .................................. 8 - 2
Accessing the Wireless Menu ........................................................................................... 8 - 2
Removing Devices from the system .................................................................................. 8 - 2
Programming a replacement Telepack-608 (0998-00-0191-XX) ....................................... 8 - 3
Programming the Telepack-608 ........................................................................................ 8 - 4
Programming Replacement Instrument Radios (0040-00-0361-XX) ................................. 8 - 4
Programming the Devices ................................................................................................. 8 - 5
Assigning a replacement Telemetry Device to the Central Station .................................... 8 - 5
Assigning a new Telemetry Device to the Central Station ................................................. 8 - 6
Removing a telemetry device from the Equipment List ..................................................... 8 - 6
To re-enter a device after being deleted: ........................................................................... 8 - 6
Appendix C ................................................................................................................................... 9 – 1
Connection Diagrams .............................................................................................................. 9 - 3
Central Stations ................................................................................................................. 9 - 3
View/Work Stations ........................................................................................................... 9 - 4
Telemetry Servers (0998-00-0206-01) .............................................................................. 9 - 4
Wireless Transceiver (0998-00-0710-01) .......................................................................... 9 - 6
Gateway ............................................................................................................................ 9 - 6
e-Gateway ......................................................................................................................... 9 - 6
KVM Extenders ................................................................................................................. 9 - 7
Laser Printers .................................................................................................................... 9 - 11
Ethernet Switches ............................................................................................................. 9 - 12
Panorama™ Service Manual
iii
Foreword
The Panorama™ Service Manual is a guide for technically-qualified personnel who perform
maintenance and/or repair on the Panorama Patient Monitoring Network.
The Service Manual conveys system-wide information that is divided into sections. For quick reference, each
chapter’s title page displays a table of contents that indicates, by sections, the topics covered.
This publication may have been updated to reflect product design changes and/or manual improvements.
NOTE: Unauthorized servicing may void the remainder of the warranty. Check with the factory or with a local
authorized representative to determine the warranty status
Warnings, Cautions, and Notes
Please read and adhere to all warnings, cautions, and notes listed here and in the appropriate areas throughout
this manual.
A WARNING is provided to alert the user to potential serious outcomes (death, injury, or serious adverse
events) to the patient or the user.
A CAUTION is provided to alert the user signaling that special care is necessary for the safe and effective use
of the device. They may include actions to be taken to avoid effects on patients or users that may not be
potentially life threatening or result in serious injury, but about which you should be aware.
A NOTE is provided when additional general information is applicable.
WARNINGS
WARNING: Do not attempt to use either Panorama ® Patient Network
or Central Network, including cabling for any purpose other
than its intended use.
WARNING: Route cables neatly. Ensure cables are not in the way of
patients or hospital personnel.
WARNING: Loading any unauthorized software including utilities on
Panorama® Patient Monitoring Network will cause the
application to no longer be suitable for medical patient
monitoring use.
WARNING: Do not connect or attempt to connect or reconfigure any
equipment to Panorama ® Central Station Patient Network
or Central Network LANs unless authorized in writing.
This includes all commercially available networking hardware]
i.e., switches, routers etc.) or peripherals (i.e., Printers) even
if they are the same brand as recommended by the
configuration of the system and supplied by the manufacturer.
iv
Panorama™ Service Manual
WARNING: Do not attempt to load any devices or device drivers onto
the Panorama® Central Station. If the user connects or attempts
to connect any equipment Panorama ® Central Monitoring
System may not operate as intended.
WARNING: Only qualified and trained service personnel or Service
personnel should attempt to service equipment. Service is
defined as any activity requiring the cover to be removed
for internal adjustments, parts replacements, repairs or
software upgrades of any kind to insure compatibility.
WARNING: To insure compatibility with the operating system and
applications software, use only the supplied and/or
approved components to repair any part of the
Panorama Patient Monitoring Network. Use of unauthorized
software, devices, accessories, or cables other than those
approved may render the application unsuitable for medical
patient monitoring. It may also result in increased electromagnetic
Emissions or decreased Immunity of the system.
WARNING: Do not block or turn down the volume from the maximum
position on the speakers provided with Panorama ® Central
Monitoring System. Set the volume levels so that alarms can
be heard at all times, as described in the Operation Manual.
WARNING: Be careful not to turn off patient alarms. Turning off patient
alarms can jeopardize patient safety.
WARNING: Do not incinerate batteries, possible explosion may occur.
WARNING: The 18.1" flat panel may tip over, if the display head
is inclined to an angle greater than 45°backward tilt. If the
user elects to have the display head inclined to an angle
greater than 45°, backward tilt, the flat panel must be
attached to a secure mounting surface via three screw
locations on the bottom of the base.
WARNING: The Panorama Central Station and the Panorama Telemetry
Server must utilize the hospital emergency power system.
Failure to do so will result in loss of monitoring during
extended periods of power failure. The back-up power time
period, for the Panorama Patient Monitoring Network, is limited.
Panorama™ Service Manual
v
WARNING: Do not put MPSO (Multiple Portable Socket Outlets, i.e.,
multiple outlet extension cords) used with the Panorama
Central Station System on the floor. Connect only Panorama
Central Station accessories and components to the same
MPSO as the Panorama Central Station. Do not overload
MPSOs. Use only MPSOs that comply with the requirements
of IEC 60601-1-1.
WARNING: Do not clean the monitor while it is on and/or plugged in.
CAUTIONS
CAUTION: This system is intended for use in a hospital or clinical
setting and to be operated by trained and authorized
personnel who are acting on the orders of a physician. Its
purpose is the real time monitoring of a patient's
physiological parameters over an extended time frame.
CAUTION: For proper operation do not obstruct the fan air holes.
CAUTION: For proper operation never place fluids on top of this
equipment. In case of accidental spillage, wipe clean
immediately and have the system serviced to ensure no
hazard exists.
CAUTION: For proper operation do not use Panorama Patient
Monitoring Network with a frayed or damaged power cord.
CAUTION: Do not operate Panorama® or any of its components if they
have been dropped or the case has been damaged.
CAUTION: Use only the supplied power cords or if a substitute is
necessary, only use Hospital Grade power cords.
CAUTION: For proper operation use only approved accessories
with this product.
CAUTION: Dispose of single use items in accordance with hospital
policy.
CAUTION: Software is written directly to some of the PC boards within
the computers. Replacement of the PC boards with off-the-shelf
PC boards may compromise the proper operation of the
Central Station Network.
vi
Panorama™ Service Manual
How to Get Help
Phone Numbers and How to Get Assistance
A network of service representatives and factory-trained distributors is available. Before requesting service,
perform a complete operational check of the instrument to verify proper control settings. If operational problems
continue to exist
,
In North and South Americas, contact the Service Department at (800) 288-2121, ext: 7875 for arranging a
service or (201) 995-8000 for assistance in determining the nearest field service location.
In areas other than North and South America, contact Mindray’s agents or Mindray service centers in your
region. If Mindray service centers are not available in your region, please contact the Customer Service of
Mindray headquarters in Shenzhen at (86) 755 26582492 or (86) 26582888 for technical support or assistance.
Please include the instrument model number, the serial number, and a description of the problem with all
requests for service.
Warranty questions should be directed to a local Mindray representative.
Manufacturer's Responsibility
Mindray DS USA is responsible for the effects on safety, reliability, and performance of the equipment only if:
assembly operations, extensions, readjustments, modifications or repairs are carried out by persons authorized
by Mindray; and the electrical installation of the relevant room complies with the appropriate requirements; and
the equipment is used in accordance with the instructions for use.
Panorama™ Service Manual
vii
This page intentionally left blank.
viii
Panorama™ Service Manual
1.0
Instrument Description
1.1 Introduction ....................................................................................................................... 1 – 2
1.2 Panorama Telemetry ......................................................................................................... 1 – 2
1.3 System Modules, Components and Peripherals ............................................................... 1 - 5
1.4 Theory of Operation .......................................................................................................... 1 - 7
Panorama™ Service Manual
1-1
1.1 Introduction
This section of the service manual initially provides a high-level overview of the Panorama ® Patient Monitoring
Network, followed by more detailed information.
1.1.1 Overview
The Panorama Patient Monitoring Network is a comprehensive patient care monitoring and management
system designed for use in a hospital setting. The system is intended to be installed and used in a fixed, non portable, permanent location that serves as a central data viewing station. The Panorama Patient Monitoring
Network consists of the following four primary modules that are linked to and/or by one another:
Panorama Central Station
Panorama Central Network
Panorama Patient Network
Bedside Monitors
NOTE: Optional modules include 2.4 GHz telemetry and WMTS telemetry for wireless operation.
Hardware and software components within each module provide system-wide functionality and connectivity.
Patient information is routed to the Panorama Patient Monitoring Network via the four modules. Information is
sent across a network provided to and by the Panorama Patient Network and the Panorama Central Network
modules. The Panorama Patient Network connects the Passport 2 ® and PassportV®, Spectrum ® and Spectrum
OR®, DPM6, DPM7 and V12 and V21 monitors via a proprietary wired Ethernet network. The monitoring
capacity of the system is flexible and uses industry standard components to provide network communications to
all connected patient monitors and peripheral devices. The Panorama Central Network connects two or more
Panorama Central Stations and/or laser printers.
This service manual focuses on the Panorama Central and Telemetry Server modules since they are the hands on interface between the medical staff and the Panorama Patient Monitoring Network. The Panorama Central
Station module is a combination of both hardware (e.g., Central Station computer and display monitor) and
software components (i.e., Panorama software applications). Much of the patient information processing and
data management occurs within the Central Station.
1.2 Panorama Telemetry
The Panorama Wireless Telemetry Server collects patient data from Passport V 2.4 GHz, DPM6, 2.4 GHz,
Spectrum, Passport2 WMTS bedside monitors and/or Ambulatory Telemetry Packs (Telepack608) via ceiling or
wall mounted antennas and/or Access Points. This allows transport through specifically designated areas of the
hospital without disconnecting cables or discharging a patient while transporting that patient from room to room.
Patient data is displayed at the Central Station, which is mounted at the nurses’ station. The system operates in
either the 802.11 g/b band or the 608 - 614 MHz Wireless Medical Telemetry Service (WMTS) band.
Each Central Station to display up to 16 patients on dual Touch Screen displays. The Central Station’s monitor
is controlled by a set of menu keys that you activate by selecting a key on the Touch Screen monitor, or
positioning the cursor over a key and clicking the left mouse button. When you select a menu key, you receive
visual feedback.
1-2
Panorama™ Service Manual
1.2.1 Core Functions and Components
1.2.1.1 Wireless Transceiver (WMTS Only)
The Wireless Transceiver collects and processes RF data from the antenna network. The transceiver also
provides 9 VDC power to the antenna network. The Transceiver can support up can support up to 188 WMTS
devices
1.2.1.2 Telemetry Server (WMTS only)
The Telemetry Server processes the data from the Wireless Transceiver and sends the patient data to the
Patient Network. Each Telemetry Server support up can support up to 47 WMTS devices.
1.2.1.3 Connectivity
Each Panorama Central Station is designed for monitoring up to 16 hospital patients. The data is derived from
bedside monitors connected to the Panorama Patient Monitoring Network via the Panorama Patient Network
(an Ethernet connection). Patient data is received and processed by the Central Station and displayed on an
LCD display.
A laser printer produces printouts of the patient data via the Panorama Central Network.
1.2.1.4 Wireless Configurations
The wireless network configuration is remote from the nurses’ station. Located in a closet, the Panorama
Wireless Telemetry Server collects data from patient monitors via antennas and access points. The equipment
listed below is also included in the wireless configuration.
WMTS (608 - 614 MHz) Telemetry
Instrument transceivers (for Passport 2 and Spectrum bedside monitors)
Telepack-608 (patient worn transmitter)
Telemetry Server
Wireless Transceiver
Antenna Network
Active Antennas
RG6 and/or RG11 coax cable
RF Splitters
Antenna repeaters
2.4 GHz 802.11 b/g Telemetry
PassportV and DPM6 monitors with internal wireless modules
802.11 b/g Access Points
Power Injectors
CAT5e Cable
Panorama™ Service Manual
1-3
1.2.2 Panorama Block Diagram
The following block diagram illustrates the wired and wireless WMTS and 802.11b/g configurations for the
Panorama Patient Monitoring and Central Monitoring Networks.
Figure 1-1 Block Diagram
1-4
Panorama™ Service Manual
1.3 System Modules, Components, and Peripherals
1.3.1 Panorama Central Station
The Panorama Central Station contains the Panorama Patient Monitoring Network application software,
operating system, patient data processing, and data storage components.
The application software is stored on the system hard drive within the Panorama Central Station. A separate
hard drive stores patient historical data.
LCD Monitors provide a graphic display of patient waveforms, audio, and other data.
1.3.2 Network Laser Printer
A network laser printer provides ECG Strip and Patient Report printouts. One Panorama Central Station is
capable of supporting up to two printers.
The following network printers are validated for use with the Panorama Central Station:
HP LaserJet 4050n
HP LaserJet 4100n
HP LaserJet 4200n
HP LaserJet 4250n
HP LaserJet 4350n
HP LaserJet P4015n
(software versions 8.6.3 and above)
HP LaserJet M602
(software versions 11.3 and above)
1.3.3 Keyboard, Video, and Mouse (KVM) Extender
The KVM Extender allows display monitors, and mouse to be located away from the Panorama Central Station.
The KVM Extender consists of a transmitter and receiver connected via CAT5e cable. The transmitter is located
at the Central Station location, and the receiver is located at the display monitor location. Analog signals are
carried by CAT5e Ethernet cable and link the Central Station with the display monitor(s). The extenders will
support a maximum of 400 ft. (122 m.) of cable distance between the Central Station location and the LCD
monitor at the Nurses’ Station.
1.3.4 Network Ethernet Switches
Switches route data from bedside monitors and telemetry servers and transfer the data to the Panorama
Central Station.
Switches also facilitate Central Station-to-Central Station communication, and communication to network laser
printers.
1.3.5 Uninterruptible Power Supply (UPS)
UPS provides battery backup during a power outage and limited AC surge protection for all Panorama Central
Station components (except for a laser printer).
Panorama™ Service Manual
1-5
1.3.6 Access Points (optional 2.4 GHz Telemetry only)
The Access Point collects patient data transmitted from the bedside monitors and Telepack.
1.3.7 Bedside Monitors
1.3.7.1 Passport2®
The Passport 2 monitor is a four-trace vital-signs monitor that can be mounted on a rolling stand, wall mount
bracket, or tabletop. For additional information on the Passport2 monitor, refer to the Passport2 Operating
Instructions.
1.3.7.2 Spectrum TM
The Spectrum monitor is a four-trace vital-signs monitor that can be mounted on a rolling stand, wall mount
bracket, or tabletop. For additional information on the Spectrum monitor, refer to the Spectrum Operating
Instructions.
1.3.7.3 Spectrum OR TM
The Spectrum OR monitor is a three to eight-trace vital-signs monitor that can be mounted on
a rolling stand, wall mount bracket, or tabletop. For additional information on the Spectrum
OR monitor, refer to the Spectrum Operating Instructions.
1.3.7.4 Passport ® V
The Passport V monitor is a three to eight-trace vital-signs monitor that can be mounted on a rolling stand, wall
mount bracket, or tabletop. For additional information on the Passport V monitor, refer to the Passport V
Operating Instructions.
1.3.7.5 DPM6 and DPM7TM
The DPM6 and DPM7 monitors are three to five lead vital-signs monitors that can be mounted on a rolling stand,
wall mount bracket, or tabletop. For additional information on the DPM6 and DPM7 monitors, refer to the DPM6
Operating Instructions and DPM7 Operating Instructions.
1.3.7.6 V Series (V12 TM and V21TM)
The V12 and V21 monitors are three to five lead vital-signs monitors that can be mounted on a rolling stand,
wall mount bracket, or tabletop. For additional information on the V Series monitors, refer to the V Series
Operating Instructions.
1.3.8 ViewStation (Optional)
The Panorama ViewStation provides the ability to observe any patient on the Panorama network.
1-6
Panorama™ Service Manual
1.3.9 WorkStation (Optional)
The Panorama WorkStation provides the ability to observe, admit, and discharge any patient on the Panorama
network.
1.3.10 Gateway/e-Gateway (Optional)
The Panorama Gateway or e-Gateway provides an interface to the hospital information system.
1.3.11 Telemetry Server (Optional)
The Panorama Telemetry Server processes data received from Mindray WMTS devices via the wireless
network.
1.3.12 Wireless Transceiver (Optional)
The Wireless Transceiver provides DC power to the WMTS antenna network, and provides an interface to the
Panorama WMTS wireless network.
1.4 Theory of Operation
The Panorama Central Station is an 8, 12 or 16-patient channel, medical monitoring system. The station’s
design and monitor are based on the ATX computer architecture. Basic system data processing configuration
includes an ATX computer, a LCD display monitor with Touch Screen, and an Ethernet distribution system.
CAUTION: The Panorama software is written directly to some of the PC boards within the tower.
Replacement of the PC boards with off-the-shelf PC boards may compromise the proper operation of
the Central Station.
1.4.1 Panorama Central Station and Wireless Telemetry Server
Each of the Panorama Central Station’s hardware/software items (e.g., hard drives, controls, etc.,) are identified
and detailed below. Functionality and connectivity for each component and/or peripheral is mentioned where
appropriate. Specified for each is its contribution(s) to either the overall Panorama Patient Monitorin g Network
and/or to data management operations designated by system architecture for the Central Station module.
1.4.1.1 Motherboard
The motherboard is the physical platform on which the computer’s electronic circuitry and processors reside.
The computer’s Central Processing Unit (CPU) is docked on the motherboard. The CPU executes the
Panorama Patient Monitoring Network proprietary software. The following components also reside on the
motherboard:
Random Access Memory (RAM)
Read Only Memory, Basic Input/output System (ROM BIOS)
Audio Circuit and Video Circuit
EIDE or SATA controller for 3.5” floppy drive (optional), CD-ROM, and system hard drives
Patient/Central Network Interfaces
Mouse and keyboard controllers
Panorama™ Service Manual
1-7
1.4.1.2 Connected to the Motherboard via PCI connectors:
Patient Network/Telemetry Network Interface Card
AGP Graphics Display Card (if applicable)
Riser Card (2U Central cases and 2U Panorama Telemetry Server only)
Clock Card (PCI)
1.4.1.3 Connected to the Riser Card (optional)
Telemetry Network Interface Card (Panorama Telemetry Server only)
TIM PCI Card (Panorama Telemetry Server only)
AGP Graphics Display Card
1.4.1.4 System Hard Drive Assembly
The system hard drive stores the Windows Operating System and Panorama application software. It is
controlled by EIDE controller or SATA controller circuitry on the motherboard.
1.4.1.5 CD-ROM Drive
The CD-ROM drive is used to load software, copy error logs and create and load the emergency disk.
1.4.1.6 Patient Network Interface Card
The Panorama Patient Network Interface Card (NIC) sits in the J16 slot on the motherboard. It provides a 100
Mbps Ethernet interface for the Panorama Patient Network.
1.4.1.7 AGP Graphics Display Card (if applicable)
The AGP Graphics Display card sits in the J19 slot on the motherboard. There are two versions of the graphic
display card. The first version has two HD-15 connectors. The second version has one DVI connector and one
HD-15 connector. The second version requires the use of a DVI-to-HD-15 adapter. These connectors are
cabled to the display monitors or KVM extenders.
1.4.1.8 ATX Power Supply
The ATX switching Power Supply provides power for all electronic assemblies within the Panorama Central
Station. Regulated voltages are +5, -5, +12, and -12 Volts. The power supply has a universal AC input and is
rated for 300 Watts (minimum).
1.4.1.9 Disclosure Hard Drives (Central Stations, WorkStations and Gateways Only)
One disclosure hard drive stores all patient data. The IDE or SATA controller on the motherboar d controls the
hard drive.
1.4.1.10 3.5” Floppy Drive (optional)
A Diskette Drive is used for running diagnostic software and uploading software. It is controlled by Diskette
Drive controller circuitry on the motherboard.
1-8
Panorama™ Service Manual
1.4.1.11 Clock Card (Central Stations, Workstations and Gateways only)
The clock card acts as the computer’s system time source, bypassing the motherboard’s clock circuit.
1.4.2 Central Station Displays
1.4.2.1 LCD Display
All digital and waveform information is displayed on the LCD screen. The unit is powered from an external AC
power supply. Video information is transmitted through a VGA cable from the VGA Card or onboard video circuit
from the motherboard.
Touch Screen
The Touch Screen consists of a flat glass plate that fits over the face of a CRT or LCD monitor display, and is
an integral part of the monitor. The Touch Screen controller is located inside the monitor housing. A DB -9 serial
cable connects each monitor to the Serial Interface Card or Serial Port on the Panorama Central Station. The
Touch Screen uses surface acoustic wave (SAW) technology.
Principles of Operation
Surface acoustic waves (SAW) are mechanical waves that propagate in the surface of the medium in which
they are generated. The actual detection and location of a finger touch on a SAW Touch Screen depends on
the absorption of a subsection of the Touch Screen’s SAW energy by the finger touching the screen.
The Touch Screen creates an absence of SAW energy. SAW energy is coupled to and extracted from the
Touch Screen by four identical piezoelectric transducers and a nearly invisible array of fired -on glass-fit
acoustic reflector strips around the border of a glass panel.
1.4.2.2 Audio
The internal speakers in the LCD monitor provide the audio feedback of the Central Stations physiological and
technical alarms.
Panorama™ Service Manual
1-9
This page intentionally left blank.
1 - 10
Panorama™ Service Manual
2.0
Repair Information
2.1 Introduction ....................................................................................................................... 2 – 2
2.2 Safety Precautions ............................................................................................................ 2 – 2
2.3 Equipment and Special Tools Required ............................................................................ 2 – 2
2.4 Troubleshooting ................................................................................................................ 2 – 3
2.5 Disassembly Instructions .................................................................................................. 2 – 14
Panorama™ Service Manual
2-1
2.1 Introduction
This section provides the necessary technical information to perform repairs to the system. The most important
prerequisites for effective troubleshooting are a thorough understanding of the system functions and the theory
of operation. If necessary, refer to the appropriate Panorama Patient Monitoring Network Operating Instructions
Manual, which describes instrument functions and features in full detail.
2.2 Safety Precautions
In the event the instrument covers are removed, make certain you observe the following warnings and general
guidelines:
Do not short component leads together.
Observe proper anti-static precautions.
2.3 Equipment and Special Tools Required
You will need the following equipment and/or special tools when performing repairs:
Anti-static Wrist Strap
Anti-static Mat
#1 Phillips Screwdriver
#2 Phillips Screwdriver
Slotted Screwdriver
2-2
Panorama™ Service Manual
2.4 Troubleshooting
The Central Station’s components can be separated into three (3) sections:



Central Station and Displays
Networks (Central, Patient, and Wireless)
Bedside Patient Monitors and Telemetry Devices
During the Central Station’s installation process, a configuration sheet was created to list all IP addresse s,
subnet mask numbers, etc. assigned to the Central Station, Panorama Wireless Telemetry Servers and bedside
monitors. Refer to that configuration sheet if you cannot retrieve the information from the Central Station, or
Panorama Wireless Telemetry Server. If you do not have the list, contact the Service Representative or
Authorized Distributor that installed the system. Make sure you have the serial number of the Central Station or
Panorama Wireless Telemetry Server when calling.
Prior to troubleshooting a network problem, you should check the following areas:




All AC and DC power connections are secure.
All Ethernet cable connections are secure.
Affected cable runs should be tested with a cable tester for continuity.
IP addresses: Valid Patient Network, Central Network and Wireless Network IP addresses should be
verified.
2.4.1 Central Station and Displays
The Central Station display does not power up.
 Verify that AC power is ON at the Central Station.
 On the LCD display, turn off the power switch and turn it back on. If No Signal is displayed on the
screen, no video signals are reaching the display.
 Verify that the VGA cable between the display and the computer is making a good connection, and that
the connector screws are tight.
 If the problem persists, it is likely due to a problem within the tower.
Reboot the Central Station. Verify that the power and hard drive LEDs are illuminated and the fans are
operating.
 If the display still does not come on, the problem is likely within the tower.
 If the hard drive LED does not illuminate, the problem is likely related to the CPU or the motherboard.
 If the fans are not operating, the problem is likely the power supply.
KVM extender
 Verify DC power to both the KVM transmitter and receiver.
 Check the status of the power LED on both the transmitter and receiver. The power LED should be
illuminated and on steady (i.e., not flashing). If the LEDs are flashing or dim, this an indication of loss of
connection between the transmitter and receiver, or a failure of one or both of the power supplies.
Panorama™ Service Manual
2-3
The display powers up but the Central Station does not complete “self-test”.


Note at which point the unit stopped during the boot-up self-test (e.g., passed through the memory
check, CMOS check, Drive check).
This may mean replacement of the Network Interface Card, the Mother PCB, or one of the hard drives.
The unit went through self-test, but did not get to the Panorama operating screen. It stays at the blue screen
with no desktop icons
 Clear the error and event logs (contact a Mindray NA Service Representative or Mindray NA Technical
Support for assistance) and save the config tool
The mouse does not function.
 Verify that the connections at the rear of the Central Station are secure and that they are in the
appropriate locations.
 Check connections to the KVM Extender (Transmitter & Receiver).
 Re-power the KVM by disconnecting AC power from the transmitter and receiver. Reboot the system. Is
the mouse functional?
 If not, install a new PS2 mouse and reboot the system again.
 Is the mouse functional now? If not, this may mean replacement of the Mother PCB.
No touch screen response.
 Clean the touch screen panel.
 Verify that the connections at the rear of the Central Station are secure and that they are in the
appropriate locations.
 Check connections to the KVM Extender (Transmitter & Receiver).
 Re-power the KVM by disconnecting AC power from the transmitter and receiver Reboot the system. Is
the touch screen functional?
 If not, this may mean replacement of the touch screen monitor or the touch screen controller card.
Laser printer does not print when requested.
 Check the Print Setup menu on the Panorama Verify the printer settings on the Panorama are enabled
for reports and strips
 Verify and correct any error messages on the printer's Control Panel LCD.
 Print the laser printers configuration page. Check the configuration of the Laser printer’s jetdirect card
for the correct IP address. Mindray uses 7.7.7.XX for the central network IP address scheme.
 Verify that the printer can print a test page using the printer's control panel menu.
 Verify that the cable connections are secure between the printer and the Central Station.
 If a switch is installed, check the cable connections between the switch and the Central Network
connector at the rear of the Central Station. Verify the cable connection between the printer and the
switch.
 Verify the LED is illuminated on the network interface card on the laser printer.
 If a switch is installed, verify that the Power/Self Test LED is illuminated on the switch. Verify the
behavior of the activity LEDs at the port in which each cable is connected and the connected device is
active. The LEDs should be blinking. If all of the above are correct, the problem is likely not in the
printer.
2-4
Panorama™ Service Manual
2.4.2 Troubleshooting Bedside Communication Issues
2.4.2.1 Communication Loss from an individual Bedside Monitor
Wired Network Connection (Passport2, Spectrum, Spectrum OR)
 Verify the cable connections between the switch and Central Station, and ensure the connection at the
tower is at the Patient Network connector.
 Verify the Power LED on the switch is illuminated. Verify the activity LEDs are illuminated in
conjunction with the port in use. If not, disconnect the cable and plug it into another port. Verify the LED
of the new port illuminates and show activity
 Verify the bedside monitor is connected via a patch cable to the CAT5e wall jack.
 Verify the Link LED on the Comm Port on the bedside monitor is illuminated.
 If the Link LED does not illuminate, it may indicate that the Comm Port is defective.
 Verify a "V" in the communication status box (located in the lower right corner of the display) on the
bedside monitor, which indicates communication with the Central Station. See Figure 2-1.
FIGURE 2-1 Passport2, Spectrum and Spectrum OR
Communication Status Icon indicators
Connected
Disconnected
No Icon is displayed
Panorama™ Service Manual
2-5
PassportV
 Verify the bedside monitor is connected via a patch cable to the CAT5e wall jack.
 Verify a patch CAT5e patch cable is connected to the Ethernet Port (CS1) on the rear of the PassportV
 Check the status of the Central station icon in the lower right corner of the display (SEE Figure 2-2)
FIGURE 2-2 PassportV
Communication Status Icon indicators
Connected
Disconnected
2-6
Blank (no CS icon)
Panorama™ Service Manual
DPM 6 and DPM 7
 Verify the bedside monitor is connected via a patch cable to the CAT5e wall jack.
 Verify a patch CAT5e patch cable is connected to the Ethernet Jack on the rear of the DPM 6 or DPM7

Check the status of the Central station icon in the lower right corner of the display (see figure 2-3).
FIGURE 2-3 DPM 6 and DPM 7
Communication Status Icon indicators
Connected
Panorama™ Service Manual
Disconnected
2-7
V 12 and V21
If Network Communication Lost is displayed (see figure 2-4)
FIGURE 2-4 V Series Monitor



Verify the V Dock is connected to AC power
Verify the bedside monitor is connected via a patch cable to the CAT5e wall jack.
Verify a CAT5e patch cable is connected to the Ethernet Jack (marked CS1) on the rear of the V Dock.
Verify the Link (yellow solid) and Activity (green blinking) LEDs are illuminated on the rear of the V
dock.
2.4.3 Wireless Connections
2.4.3.1 Passport2 and Spectrum WMTS
 Verify the Radio Icon is displayed along with a V in the communication status box in the lowe r right
corner of the display)
 If the radio icon is not displayed, verify that the bedside monitor is properly configured with WMTS
Enabled (located in the Installation Menu of the Passport2 or Spectrum)
 If the bedside monitor is configured properly, verify the software version of the bedside.
 If the bedside monitor is configured properly and the software version is the correct version, reprogram
the radio card.
FIGURE 2-5 Passport2 and Spectrum
2-8
Panorama™ Service Manual
Communication Status Icon indicators
Connected
Disconnected
2.4.3.2 Telepack-608 (WMTS)
 Verify the device ID of the Telepack 608 is entered to the Central Station's equipment list.
 Connect all leads to an ECG simulator and then install two (2) new “AA” batteries into the Telepack.
 Once batteries are installed, verify that the LED display powers up in the following sequence:
LA, RA, All connected leads, Link status and battery status




If the device did not power up in the preceding sequence, press the test button on the transmitter. If the
Link Status LED and/or Battery LED do not illuminate, that indicates a fault within the transmitter.
If, however, after pressing the test button, the LED display illuminated in the following sequence: LA,
RA, LL, then that indicates the transmitter has not been programmed. Refer to Appendix B for
instructions on programming the Telepack.
Battery LED Blinking indicates less than 2 hours of run time remaining.
Link LED Blinking indicates an internal failure and must be serviced.
2.4.4 Mindray 2.4 GHz Monitors
PassportV
FIGURE 2-6 PassportV
Connected
Panorama™ Service Manual
Disconnected
2-9
DPM6
FIGURE 2-7 DPM 6
Connected
Disconnected
2.4.5 Communication Loss from all wired Bedside Monitors and Mindray 2.4 GHz equipped monitors
Wired Network
 Verify AC power to the Ethernet switch(es). Verify the Power and Status LEDs on the switch(es). Reboot the switch(es).
 Verify the Status LED for the port connecting the Central Station to the switch.
 If not illuminated, connect the patch cable to another port on the switch. If the Status LED still does not
illuminate, the problem may be with the network card in the Central Station.
 Verify the LEDs on the Patient Network card on the Central Station.
 If not illuminated, the network card may be defective.
2 - 10
Panorama™ Service Manual
2.4.6 Communication Loss from all WMTS Telemetry devices
2.4.6.1 Panorama Wireless Transceiver
 Check the status LEDs on the Panorama Wireless Transceiver.
 If the Status LED (blue) is illuminated, an internal error in the Wireless Transceiver has occurred. with
the main board
 If the Status LED (blue) is blinking, they is probably a problem with the power supply
 If the Fault LED (red) is illuminated, this indicates an internal error has occurred within the Wireless
Transceiver or a short in the antenna network. The Wireless Transceiver and Telemetry Server must be
rebooted to clear the error.
 If the Power (green) and Configured (yellow) LEDs are not illuminated, check if AC power is connected.
If power is connected, disconnect the AC cord and check the fuse in the power entry module. Re boot
the Panorama Wireless Transceiver and check the status of the LEDs.
 If the Power (green) and Configured (yellow) LEDs are illuminated, check the power LED on the
antennas. If the LED is not illuminated on the antennas, this indicates that no 9 VDC is being provided
by the Panorama Wireless Transceiver to the antenna grid. Each branch of the antenna grid (Main and
Diversity) has its own 9 VDC source. Check the output of each branch at the BNC connector for 8.5
VDC to 9 VDC. If either branch is less than 9 VDC, leave the branch disconnected for a short period of
time until the 9 VDC level returns. If the 9 VDC does not return to normal, reboot the Server and
measure again.
 If there is no 9V DC after a reboot, open the cover on the Transceiver and measure the Voltage on the
output of Power supply at TP1 (-) and TP2 (+). It should be 9 VDC. Replace the power supply if there is
no 9 VDC.
 After rebooting and reconnecting the antennas, the antenna grid again loses 9 VDC, there may be a
short in the antenna system or the there is a problem within the Panorama Wireless Transceiver.
2.4.6.2 Panorama Wireless Telemetry Server
 If the Server is configured properly and communicating with the Wireless transceiver, the Server
displays the following text.
FIGURE 2-8 Server and Transceiver Communication established
Panorama™ Service Manual
2 - 11

When the Server completes the connection to the Central Station network, the following screen will be
displayed.
FIGURE 2-9 Confirmation of Server and Central Station Communication
If the “CB Server Created” message does not appear, the Server is not communicating with the Central Station.
Check the cabling between the Server and the Central Station.
If the Panorama Wireless Telemetry Server is communicating with the telemetry devices, and the teleme try
devices are properly programmed and assigned to the equipment list, the Server displays the following text.
FIGURE 2-10 Confirmation of Communications with Telemetry Devices
If the "WMTS Telepack Translator Initialized" message does not appear, the telemetry device may not be in the
Central Station's equipment list or the Server WMTS devices file.
If the telemetry devices are communicating with the Central Station, the Server displays the following text.
2 - 12
Panorama™ Service Manual
FIGURE 2-11 Confirmation of WMTS device Communications
Verify that each admitted WMTS bedside monitor or Telepack 608 is displayed on the Central Station.
Panorama™ Service Manual
2 - 13
2.5 Disassembly Instructions
2.5.1 Assembly Diagrams
FIGURE 2-12 Central Station, ViewStation, Workstation, and Gateway
(0998-00-0700-XX01)
FIGURE 2-13 2U Telemetry Server (0998-00-0206-10)
2 - 14
Panorama™ Service Manual
FIGURE 2-14 Central Station ViewStation, WorkStation, and Gateway
(0998-00-0705-01)
PCI Clock Card
VGA Exp. Card
Riser Card
Motherboard
Power Supply
System Hard drive
CDRW Drive
Disclosure Hard drive
0998-00-0708-01
FIGURE 2-15 Central Station, ViewStation, WorkStation, and Gateway
(0998-00-0708-01)
Panorama™ Service Manual
2 - 15
FIGURE 2-16 e-Gateway, 2U Version (0098-00-0708-03)
CDROM Drive
+
Power Supply
+
Parallel
Conn
COM3
COM4
COM2
CPU
FAN
CPU
Feature
Conn
Front
Panel
Conn
+
+
Hard Drives
ATX/BTX
POWER
+
+
ATX12V
DDR0
SATA
Conn
VGA Expansion Card
+
Clock Card
+
IDE
Conn
+
CMOS BAT
+
CLRCMOS
+
+
+
+
0998-00-0709-01
FIGURE 2-17 Central Station, ViewStation, WorkStation, and Gateway
(0998-00-0709-01)
2 - 16
Panorama™ Service Manual
CDROM Drive
+
Power Supply
+
Parallel
Conn
COM3
COM4
COM2
CPU
FAN
CPU
Feature
Conn
Front
Panel
Conn
+
+
Hard Drives
ATX/BTX
POWER
DDR1
+
+
ATX12V
DDR0
SATA
Conn
+
Clock Card
+
NIC Card
+
IDE
Conn
CMOS BAT
+
CLRCMOS
+
+
+
+
0998-00-0709-03
FIGURE 2-18 e-Gateway (0998-00-0709-03)
TIM PCI Card
Riser Card
Motherboard
Power Supply
System Hard drive
CDRW Drive
0998-00-0710-01
FIGURE 2-19 Wireless Server (0998-00-0710-01)
Panorama™ Service Manual
2 - 17
2.5.2 Disassembly instructions
2.5.2.1 0998-00-0206-10 Telemetry Server Chassis


Remove the AC power Cord
Disconnect all cables from the rear of the chassis
Top cover
 Remove the 4 screws (2 on each side) from the top cover.
 Lift off the cover.
CD-ROM Drive/Floppy Drive
 Remove the DC power and IDE cables from the rear of the drives.
 Remove the 5 screws from the drive bracket.
 Lift the drive bracket out of the chassis.
CD-ROM drive





Remove the 4 screws from the drive bracket.
Remove the drive.
Floppy drive
Remove the 4 screws from the drive bracket.
Remove the drive.
Hard drive
 Remove the DC power and IDE cables from the rear of the drive.
 Remove the 2 screws securing the hard drive housing to the chassis.
 Slide the housing towards the rear of the chassis.
 Remove the bracket from the chassis.
 Remove the 4 screws from the sides of the drive housing.
 Remove the drive from the drive housing.
Power Supply
 Disconnect the 20 pin ATX power connector from the motherboard.
 Cut any tie-wraps securing the power supply cables to the chassis.
 Disconnect the 4 pin DC power connector from the hard drive.
 Disconnect the 4 pin DC power connector from the CD-ROM drive.
 Disconnect the 4 pin DC power connector from the Floppy Drive.
 Disconnect the 4 pin DC power connector from the cooling fans.
 Remove the three screws from the rear of the chassis.
 Remove the 2 screws securing the supply to the bottom of the chassis.
 Remove the power supply from the chassis.
2 - 18
Panorama™ Service Manual
Network Interface Card
 Remove the screw securing the expansion card bracket to the chassis. Access is through a hole in the
left side panel.
 Remove the card from the riser board PCI connector.
TIM PCI Card
 Remove the screw securing the expansion card bracket to the chassis. Access is through a hole in the
left side panel.
 Remove the screws securing the card to the bracket connected to the fan assembly.
 Remove the card from the riser board PCI connector.
VGA Card
 Remove the screw securing the expansion card bracket to the chassis. Access is through a hole in the
left side panel.
 Remove the card from the riser board AGP connector.
Riser Card
 Remove the screws securing the riser card to the stiffener bar.
 Remove the screws securing the stiffener bar to the chassis. (1 from the rear panel and 1 from the fan
bracket.)
 Loosen the release catch to free the riser card. Remove the riser card assy. from the AGP/PCI
motherboard connectors.
Motherboard
 Disconnect the 20 pin ATX power cables from the power supply connector (J29).
 Disconnect the 2 IDE interface cables from the primary and secondary IDE connectors (J30 and J31).
 Disconnect the ribbon cable from the floppy drive connector (J27).
 Disconnect the 4 connectors from the system function connector (J54).
 Remove the 2 screws securing the stiffener bar to the chassis. (1 from the rear panel and 1 from the
fan bracket.)
 Remove the Network Interface card from the riser card.
 Remove the VGA card from the riser card.
 Remove the TIM PCI card from the riser card.
 Remove the riser card from the motherboard PCI connector.
 Remove the 10 screws securing the motherboard to the chassis.
 Remove the motherboard from the chassis
Microprocessor removal
 Disconnect the CPU fan connector from the motherboard (Primary Slot1 Fan J23).
 Press and loosen the two retaining clips securing the microprocessor to the plastic bracket. Remove
the microprocessor.
CMOS Battery (BAT1) removal
 Pry up on the battery to loosen the battery.
 Remove the battery.
Panorama™ Service Manual
2 - 19
2.5.2.2 0998-00-0700-01 Central Station Chassis


Remove the AC power Cord
Disconnect all cables from the rear of the chassis
Top Cover


Remove the 4 screws (2 on each side) from the top cover.
Lift off the cover.
CD-ROM Drive/Floppy Drive
 Remove the DC power and IDE cables from the rear of the drives.
 Remove the 5 screws from the drive bracket.
 Lift the drive bracket out of the chassis.
CD-ROM drive
 Remove the 4 screws from the drive bracket.
 Remove the drive.
Floppy drive
 Remove the 4 screws from the drive bracket.
 Remove the drive.
Hard drives
 Remove the DC power and IDE cables from the rear of the drives.
 Remove the 2 screws securing the hard drive housing to the chassis.
 Slide the housing towards the rear of the chassis.
 Remove the bracket from the chassis.
Individual drive removal
 Remove the 2 screws from the left side of the drive housing.
 Remove the 2 screws from the right side of the drive housing.
 Remove the drive from the drive housing.
Power Supply
 Disconnect the 4 pin ATX12V and the 20 pin ATX power connector from the motherboard.
 Cut any tie-wraps securing the power supply cables to the chassis.
 Disconnect the 4 pin DC power connector from each hard drive.
 Disconnect the 4 pin DC power connector from the CD-ROM drive.
 Disconnect the 4 pin DC power connector from the Floppy Drive.
 Disconnect the 4 pin DC power connector from the cooling fans.
 Remove the three screws from the rear of the chassis.
 Remove the 2 screws securing the supply to the bottom of the chassis.
 Remove the power supply from the chassis.
VGA Card
 Remove the screw securing the expansion card bracket to the chassis. Access is through a hole in the
left side panel.
 Remove the card from the riser board AGP connector.
2 - 20
Panorama™ Service Manual
Riser Card
 Remove the 2 screws securing the riser card to the stiffener bar.
 Remove the 2 screws securing the stiffener bar to the chassis. (1 from the rear panel and 1 from the
fan bracket)
 Remove the stiffener bar.
 Loosen the release catch to free the riser card.
 Remove the riser card assy. from the motherboard AGP1/PCI1/PCI2 connectors.
Motherboard
 Disconnect the 4 pin ATX12V and the 20 pin ATX power cables from the power supply connectors (J10
and J12).
 Disconnect the 2 IDE interface cables from the primary and secondary IDE connectors (IDE1 and IDE2).
 Disconnect the ribbon cable from the floppy drive connector (FDD1).
 Disconnect the ribbon cables from the 3 Serial port connectors (J11, J15 and J16).
 Disconnect the 5 connectors from the system function connector (J20).
 Remove the VGA card from the riser card.
 Remove the screw securing the expansion card bracket to the chassis. Access is through a hole in the
left side panel. Remove the bracket.
 Remove the riser card from the motherboard PCI connector.
 Remove the 10 screws securing the motherboard to the chassis.
 Remove the motherboard from the chassis
Microprocessor removal
 Unplug the CPU fan connector from the motherboard.
 Lift the 2 heat sink/fan assembly retention clips. If necessary, remove the power supply for access to
the clips.
 Remove the Fan assembly.
 Lift the CPU socket locking lever.
 Remove the microprocessor.
CMOS Battery (BAT1) removal
 Press the metal latch on the battery holder to free the battery.
 Remove the battery.
Panorama™ Service Manual
2 - 21
2.5.2.3 0998-00-0705-01 Central Station Chassis


Remove the AC power Cord
Disconnect all cables from the rear of the chassis
Front Panel
 Grasp the Front Panel at the cutout in the bottom of the front panel.
 Pull out and up to remove.
 Left side cover
 Remove the 2 screws from the rear of the left side panel.
 Pull the cover towards the rear of the unit.
Auxiliary Fan (Front Panel)
 Remove the DC power connector from the FAN3 connector on the motherboard
 Remove the 4 screws securing the fan to the chassis.
 Remove the fan.
Auxiliary Fan (Rear Panel)
 Remove the DC power connector from the FAN2 connector on the motherboard
 Remove the 4 screws securing the fan to the chassis.
 Remove the fan.
CD-ROM Drive
 Remove the DC power and IDE cables from the rear of the drive.
 Remove the 2 screws from the left side of the drive.
 Press and hold the retainer clip on the front of the chassis.
 Pull the drive out through the front of the chassis.
Floppy Drive/Hard drive
 Remove the DC power and IDE cables from the rear of the drives.
 Remove the 1 screw from the left side of the drive housing.
 Remove the 2 or 3 screws from the front of the chassis.
 Pull the drive housing out through the front of the chassis.
Individual drive removal
 Remove the 2 screws from the left side of the drive housing.
 Remove the 2 screws from the right side of the drive housing.
 Remove the drive from the drive housing.
Power Supply
 Disconnect the 4 pin ATX12V (J12) and the 20 pin ATX power (J10) connectors from the motherboard.
 Remove the 4 pin DC power connector from each installed drive.
 Cut any tie-wraps securing the power supply cables to the chassis.
 Remove the four screws from the rear of the chassis.
 Remove the power supply from the chassis.
2 - 22
Panorama™ Service Manual
VGA Card
 Remove the screw securing the expansion card bracket to the chassis.
 Press down on the locking tab to free the card.
 Remove the card from the motherboard’s AGP connector.
Motherboard
 Disconnect the 4 pin ATX12V and the 20 pin ATX power cables from the power supply connectors.
 Disconnect the 2 80 pin or 40 pin IDE interface cables from the Primary (IDE1) and Secondary (IDE2)
IDE connectors.
 Disconnect the 34 pin ribbon cable from the FDD1 connector.
 Disconnect the ribbon cables from the 3 COM port connectors).
 Disconnect the 4 connectors from the front panel connector.
 Remove the 2 Serial port expansion brackets from the chassis.
 Remove the 10 screws securing the motherboard to the chassis.
 If necessary, remove the 6 standoffs and washers from the rear of the chassis securing EMI shield to
the motherboard.
 Remove the motherboard from the chassis.
Microprocessor removal
 Unplug the CPU fan connector from FAN1 connector the motherboard.
 Remove the 4 screws securing the fan to the heat sink. Remove the fan.
 Remove the 4 screws securing the heat sink.
 Remove the heat sink assembly.
 Lift the CPU socket locking lever.
 Remove the microprocessor.
CMOS Battery (BAT1) removal
 Press the retaining clip towards the outside of the motherboard.
 Remove the battery.
2.5.2.4 0998-00-0708-01 0998-00-0708-03 0998-00-0710-01 Central Station ViewStation WorkStation eGateway Wireless Server Chassis


Remove the AC power Cord
Disconnect all cables from the rear of the chassis
Top Cover
 Remove the 4 screws (2 on each side) from the top cover.
 Lift off the cover.
CD-ROM Drive
 Remove the power and IDE cables from the rear of the drive.
 Remove the 6 screws from the drive bracket.
 Remove the 4 screws from the drive bracket.
 Remove the drive.
Panorama™ Service Manual
2 - 23
Hard drive
 Remove the power and SATA cables from the rear of the drive.
 Remove the 2 screws securing the hard drive housing to the chassis.
 Slide the housing towards the rear of the chassis.
 Remove the bracket from the chassis.
Individual drive removal
 Remove the 2 screws from the left side of the drive housing.
 Remove the 2 screws from the right side of the drive housing.
 Remove the drive from the drive housing.
Power Supply
 Disconnect the 4 pin ATX12V and the 20 pin ATX power connector from the motherboard.
 Cut any tie-wraps securing the power supply cables to the chassis.
 Remove the DC power connector from each hard drive.
 Remove the 4 pin DC power connector from the CD-ROM drive.
 Disconnect the 4 pin DC power connector from the cooling fans.
 Remove the three screws from the rear of the chassis.
 Remove the 2 screws securing the supply to the bottom of the chassis.
 Remove the power supply from the chassis.
VGA Expansion Card (Central Stations View/WorkStations only)
 Remove the screw securing the expansion card bracket to the chassis.
 Remove the bracket
 Remove the card from the motherboard PCI connector.
Clock Card (PCI) Central Station, View/Workstations, gateways only)
 Remove the screw securing the expansion card bracket to the chassis.
 Remove the clock card from the riser board PCI connector
Riser Card (Remove the PCI clock card from the riser card.
 Remove the screw securing the riser card to the stiffener bar.
 Remove the riser card from the motherboard PCI connector.
Clock Card assembly
 Remove the screw securing the card bracket to the chassis.
 Remove the ribbon cable connecting the clock card assembly to the motherboard feature connector.
2 - 24
Manual
Panorama™ Service
Motherboard
 Disconnect the 4 pin ATX12V and the 20 pin ATX power cables from the power supply connectors.
 Disconnect the 2 SATA interface cables.
 Disconnect the ribbon cable from the parallel port connector.
 Disconnect the ribbon cable from the IDE connector.
 Disconnect the ribbon cables from the 3 COM port connectors.
 Disconnect the 3 connectors from the front panel connector.
 Remove the clock card from the riser card.
 Remove the riser card from the motherboard PCI connector.
 Remove the VGA expansion card from the motherboard.
 Remove the 6 screws securing the motherboard to the chassis.
 Remove the motherboard from the chassis. If necessary, remove the 2 screws securing the stiffener
bar to the chassis. (1 from the rear panel and 1 from the fan bracket.)
Microprocessor removal
 Unplug the CPU fan connector from the motherboard.
 Lift the 2 fan retention clips.
 Remove the Fan assembly.
 Lift the CPU socket locking lever.
 Remove the microprocessor.
CMOS Battery (BAT1) removal
 Press the retaining clip towards the outside of the motherboard.
 Remove the battery.
 Remove the 4 screws from the drive bracket.
 Remove the drive.
Panorama™ Service Manual
2 - 25
2.5.2.5 0998-00-0709-01 0998-00-0709-03 Central Station and Gateways Chassis
Top cover
 Remove the AC power Cord
 Remove the 2 screws from the rear of the left side panel.
 Pull the cover towards the rear of the unit.
Front Panel
 Grasp the Front Panel at the cutout in the bottom of the front panel.
 Pull out and up to remove.
CD-Rom Drive (IDE)
 Remove the power and IDE cables from the rear of the drive.
 Remove the 2 screws from the left side of the drive.
 Press and hold down the retainer clip on the front of the chassis.
 Pull the drive out through the front of the chassis.
CD-Rom Drive (SATA)
 Remove the power and SATA cables from the rear of the drive.
 Remove the 6 screws from the drive bracket.
 Lift the drive bracket out of the chassis.
 Remove the 4 screws from the drive bracket.
 Remove the drive.
Hard drives
 Remove the power and SATA cables from the rear of the drives.
 Remove the screw from the left side of the drive housing.
 Remove the 2 screws from the front of the chassis.
 Pull the drive rack out through the front of the chassis.
Individual drive removal
 Remove the 2 screws from the left side of the drive housing.
 Remove the 2 screws from the right side of the drive housing.
 Remove the drive from the drive housing.
Power Supply
 Disconnect the 4 pin ATX12V and the 20 pin power connector from the mother board.
 Remove the power connector from each hard drive.
 Remove the power connector from the CD-Rom drive
 Cut any tie-wraps securing the power supply cables to the chassis.
 Remove the four screws from the rear of the chassis.
 Remove the power supply from the chassis.
Network card (NIC)
 Remove the screw securing the expansion card bracket to the chassis.
 Remove the card from the mother board connector.
Clock Card (PCI)
 Remove the screw securing the expansion card bracket to the chassis
 Remove the Clock card from the motherboard
2 - 26
Panorama™ Service Manual
Clock Card Assy.
 Remove the screw securing the expansion card bracket to the chassis.
 Remove the ribbon cable from the motherboard feature connector.
Mother Board
 Remove the 2 cables from the power supply connectors.
 Remove the SATA data cables.
 Remove the ribbon cable from the parallel port connector.
 Remove the ribbon cable from the IDE connector.
 Remove the ribbon cables from the 3 COM port connectors.
 Remove the 3 connectors from the front panel connector.
 Remove all PC cards from the mother board connectors.
 Remove the 6 screws securing the mother board to the chassis.
 Remove the mother board from the chassis.
Panorama™ Service Manual
2 - 27
2.5.2.6 0998-00-0710-01 Telemetry Server Chassis


Remove the AC power Cord
Disconnect all cables from the rear of the chassis
Top cover
 Remove the 4 screws (2 on each side) from the top cover.
 Lift off the cover
CD-ROM Drive
 Remove the DC power and IDE cables from the rear of the drive.
 Remove the 5 screws from the drive bracket.
 Lift the drive bracket out of the chassis.
 Remove the 4 screws securing the drive to the drive bracket.
 Remove the drive
Hard drive
 Remove the DC power and SATA cables from the rear of the drive.
 Remove the 2 screws securing the hard drive housing to the chassis.
 Slide the drive housing towards the rear of the chassis.
 Remove the housing from the chassis.
 Remove the 2 screws from the left side of the drive housing.
 Remove the 2 screws from the right side of the drive housing.
 Remove the drive from the drive housing.
Power Supply
 Disconnect the 4 pin ATX12V and the 20 pin ATX power connector from the motherboard.
 Cut any tie-wraps securing the power supply cables to the chassis.
 Remove the DC power connector from the hard drive.
 Remove the 4 pin DC power connector from the CD-ROM drive.
 Disconnect the 4 pin DC power connector from the cooling fans.
 Remove the three screws from the rear of the chassis.
 Remove the 2 screws securing the supply to the bottom of the chassis.
 Remove the power supply from the chassis.
TIM PCI Card
 Remove the screw securing the expansion card bracket to the chassis. Access is through a hole in t he
left side panel.
 Remove the 2 screws securing the card to the bracket connected to the fan assembly.
 Remove the card from the riser board PCI connector.
Riser Card
 Remove the screw securing the riser card to the stiffener bar.
 Remove the riser card from the motherboard PCI connector.
2 - 28
Panorama™ Service Manual
Motherboard
 Disconnect the 4 pin ATX12V and the 20 pin ATX power cables from the power supply connectors.
 Disconnect the SATA interface cable.
 Disconnect the ribbon cable from the IDE connector.
 Disconnect the 4 connectors from the front panel connector.
 Remove the riser card from the motherboard PCI connector.
 Remove the 2 screws securing the stiffener bar to the chassis. (1 from the rear panel and 1 from the
fan bracket.)
 Remove the stiffener bar.
 Remove the 6 screws securing the motherboard to the chassis.
 Remove the motherboard from the chassis.
Microprocessor
 Disconnect the CPU fan connector from the motherboard (Primary Slot1 Fan J23).
 Press and loosen the two retaining clips securing the fan assembly to the plastic bracket. Remove the
fan assembly.
 Lift the retaining arm to free the microprocessor from the socket.
 Remove the microprocessor.
CMOS Battery (BAT1)
 Pry up on the retaining clip to loosen the battery.
 Remove the battery.
Panorama™ Service Manual
2 - 29
2.5.2.7 Wireless Transceiver


Disconnect the AC power cord.
Disconnect all cables from the front and rear panels, noting their original locations.
11
6
9
5
8
12
4
10
7
13
3
1
2
1. A RF Input Connector
2. B RF Input Connector
3. High current 9 VDC connector
4. 5/12 V DC connector
5. Font Panel LED Connector
6. AC Input Module and fuse
7. Fan Assembly
8. Power Supply
9. Power Supply Screws
10. Fan Screws
11. Rear connector screws
12. TIM Transceiver Board
13. Top Cover Screws
Top Cover
 Remove the top cover by removing the 20 screws.
Power Supply
 Disconnect the AC input cable from SK2.
 Remove the four external screws securing the Power Supply to the chassis.
 Unlock and disconnect the 10 pin connector (marked PUS) from SK1.
 Disconnect the black and red wires from TB1 (black) and TB2 (red).
2 - 30
Panorama™ Service Manual
TIM Radio Transceiver Board
 Disconnect the LED cable from J130.
 Unlock and disconnect the 5/12 V DC connector (marked TIM) from J101.
 Disconnect the 9V DC connectors from J1, noting their original locations.
 Disconnect the RF coax cables from J2 (A) and J3 (B).
 Remove the screws securing DS1 thru DS4 to the rear panel.
 Remove the screws securing the PC board to the chassis.
 Carefully remove the PC board from the chassis.
Internal Fan
 Remove the 4 screws and nuts securing the fan to the side panel.
 Disconnect the white and black power AC terminals from the fan.
Panorama™ Service Manual
2 - 31
This page intentionally left blank.
2 - 32
Panorama™ Service Manual
3.0 Parts Replacement
3.1 Introduction ....................................................................................................................... 3 - 2
3.2 Available Replacement Parts and Assemblies .................................................................. 3 - 2
3.3 Product Variations ............................................................................................................. 3 - 2
3.4 Parts pricing information ................................................................................................... 3 - 2
3.5 Ordering Information ......................................................................................................... 3 - 2
3.6 Parts description by assembly number ............................................................................. 3 - 3
Panorama™ Service Manual
3-1
3.1 Introduction
This section of the service manual contains a list of replacement parts for the Panorama Patient Monitoring
Network.
3.2 Available Replacement Parts and Assemblies
Replacement parts at a board or assembly level are available. In most cases, individual components on boards
and assemblies are not available. Contact the Service Department or your local authorized Service
Representative for additional details.
Panorama printed circuit boards make extensive use of multi-layer and surface-mount technology. Individual
component replacement is not recommended on these boards. Board replacement is the most efficient method
of repair for these types of assemblies.
3.3 Product Variations
Product variations, due to differences in line voltages or option differences, may require different components.
These variations are reflected, where necessary, on the parts lists.
3.4 Parts Pricing Information
Current replacement parts and pricing is determined by contacting the Order Entry Department.
3.5 Ordering Information
Please follow these guidelines when ordering replacement items for the Panorama Patient Monitoring Network.
Include the unit's model and serial number.
Include the software revision.
Include the part number exactly as it appears in the parts list.
Include the description of the part.
NOTE: The Mindray maintains a policy of continuous development of product improvement and reserves the
right to change materials, specifications and prices without notice.
Individual assemblies may contain a different part number for the same item. Reference the
0998-XX-XXXX-XX assembly number when ordering parts and assemblies.
The following tables list the parts and part numbers associated with the individual chassis or assembly.
3-2
Panorama™ Service Manual
3.6 Parts description by assembly number
0998-00-0700-01 2U Chassis (Central, View/Workstation or Gateway)
PT serial number prefix
Description
Part Number
Power Supply, 500W ATX min.
Mother Board ATX Pentium 4 (refurbished)
Riser Card PCI/AGP/PCI
Video Card, AGP
Floppy Disk Drive 3.5 inch
CD-RW Drive (IDE)
System Hard Drive 80GB min. (IDE)
Disclosure Hard Drive 200 /250 GB min. (IDE)
Microprocessor Pentium 4 2.4 GHz
Memory Module 512 MB
Heat Sink w/Fan P4
Cable, Floppy drive
Cable, Ultra ATA IDE Drive 2 ft.
CMOS Battery (3VDC)
0014-00-0062-01
0671-UC-0052-01
0671-00-0054-01
0671-00-0220-02
0992-00-0121
0992-00-0178-01
0992-00-0084-06
0992-00-0204-01
0992-00-0205-01
0671-00-0053-01
0992-00-0211-01
0012-00-1354
0012-00-1546-01
0146-00-0078
0998-00-0705-01 Vertical Chassis (Central, View/Workstation or Gateway)
EU serial number prefix
Description
Part Number
Power Supply, ATX 460 Watt min.
Mother Board ATX Pentium 4
Video Card, AGP
Floppy Disk Drive 3.5 inch
CD-RW Drive (IDE)
System Hard Drive 80GB min. (IDE)
Disclosure Hard drive 200 GB min. (IDE)
Microprocessor Pentium 4 2.8 GHz
Memory Module 512 MB
Fan, Chassis 90mm
Fan Microprocessor
Cable, Ultra ATA IDE Drive 2 ft.
Cable, Floppy drive
CMOS Battery (3VDC)
0014-00-0075-01
0671-00-0052-01
0671-00-0220-02
0992-00-0121
0992-00-0178-01
0992-00-0084-06
0992-00-0204-01
0992-00-0205-01
0671-00-0053-01
0119-00-0214-03
0992-00-0229-01
0012-00-1546-01
0012-00-1354
0146-00-0078
Panorama™ Service Manual
3-3
0998-00-0206-10 Chassis (2U Telemetry Server) WS serial number prefix
Description
Part Number
Power Supply, 500W ATX min.
Mother Board Pentium II
Riser Card PCI/AGP/PCI
Video Card, AGP
Network Interface Card
TIM PCI Card
Floppy Disk Drive 3.5 inch
CD-RW Drive (IDE)
System Hard Drive 80GB min. (IDE)
Microprocessor Pentium II
Memory Module 128 MB
Cable, Floppy drive
Cable, Ultra ATA IDE Drive 2 ft.
CMOS Battery (3VDC)
0014-00-0062-01
0671-00-0174-02
0671-00-0054-02
0671-00-0220-02
0671-00-0178-04
0670-00-0744-02
0992-00-0121
0992-00-0178-01
0992-00-0084-06
0992-00-0079
0671-00-0173-01
0012-00-1354
0012-00-1546-01
0146-00-0078
0998-00-0708-01 2U Chassis (Central, View/WorkStation or Gateway)
RM Serial number prefix
Description
Part Number
Power Supply ATX 300 W min.
Mother Board Intel Dual Core
Video Expansion Card
CD-RW Drive SATA
System Hard Drive 160 GB min. (SATA)
Disclosure Hard Drive 250 GB min. (SATA)
Microprocessor T2500
Heat sink/Fan Assembly
Memory Module 1 GB DDR2
Clock card (PCI)
Clock Card Assy.
Riser Card
CMOS Battery (3VDC)
SATA power adapter cable
0014-00-0094
0671-00-0115
0671-00-0116
0992-00-0178-02
use 0992-00-0287
0992-00-0287
0992-00-0285
0992-00-0289
0671-00-0266
0671-00-0267
0671-00-0273
0671-00-0268
0146-00-0078
0012-00-1785
3-4
Panorama™ Service Manual
0998-00-0709-01 Chassis (Central or View/WorkStation) VM Serial number
Description
Part Number
Power Supply ATX 300 W min.
Mother Board Intel Dual Core
Video Expansion Card
CD-RW Drive SATA
System Hard Drive 160 GB min. (SATA)
Disclosure Hard Drive 250 GB min. (SATA)
Microprocessor T2500
Heat sink/Fan Assy.
Memory Module 1 GB DDR2
Clock Card (PCI)
Clock Card Assy.
CMOS Battery (3VDC)
0014-00-0093
0671-00-0115
0671-00-0116
0992-00-0178-01
use 0992-00-0287
0992-00-0287
0992-00-0285
0992-00-0289
0671-00-0266
0671-00-0267
0671-00-0273
0146-00-0078
0998-00-0710-01 Chassis (2U Telemetry Server) TE serial number prefix
Description
Part Number
Power Supply, ATX 300 W min.
Mother Board Intel Dual Core
CD-RW Drive SATA
System Hard Drive 160 GB min. (SATA)
Microprocessor T2500
Heat sink/Fan Assembly
Memory Module 1 GB DDR2
TIM PCI Card
Riser Card
CMOS Battery (3VDC)
SATA power adapter cable
0014-00-0094
0671-00-0115
0992-00-0178-02
use 0992-00-0287
0992-00-0285
0992-00-0289
0671-00-0266
0670-00-0744-02
0671-00-0268
0146-00-0078
0012-00-1785
0998-00-0708-03 Chassis (2U e-Gateway) RM Serial number prefix
Description
Part Number
Power Supply, ATX 300 W min.
Mother Board Intel Dual Core
CD-RW Drive SATA
System Hard Drive 160 GB min. (SATA)
Disclosure Hard Drive 250 GB min. (SATA)
Microprocessor T2500
Heat sink/Fan Assembly
Clock Card Assy.
Memory Card 2 GB DDR2
Network Interface Card
Riser Card
CMOS Battery (3VDC)
SATA power adapter cable
0014-00-0094
0671-00-0115
0992-00-0178-02
use 0992-00-0287
0992-00-0287
0992-00-0285
0992-00-0289
001-000252-00
023-000303-00
023-000262-00
0671-00-0268
0146-00-0078
0012-00-1785
Panorama™ Service Manual
3-5
0998-00-0709-03 Vertical Chassis e-Gateway VM Serial number prefix
Description
Part Number
Power Supply, ATX 300 W min.
Mother Board Intel Dual Core
CD-RW Drive SATA
System Hard Drive 160 GB min. (SATA)
Disclosure Hard Drive 250 GB min. (SATA)
Microprocessor T2500
Heat sink/Fan Assy.
Clock Card Assy.
Memory Module 2 GB DDR2
Network Interface Card
CMOS Battery (3VDC)
SATA power adapter cable
0014-00-0093
0671-00-0115
0992-00-0178-02
use 0992-00-0287
0992-00-0287
0992-00-0285
0992-00-0289
001-000252-00
023-000303-00
023-000262-00
0146-00-0078
0012-00-1785
0998-00-0190-02 (Wireless Transceiver)
Description
Part Number
Fuse GMA 2.5A 250V
Power Supply
TIM Radio Transceiver
Cooling Fan
0159-00-0055-17
0014-00-0060-02
0670-00-0745-01
0119-00-0206
0998-00-0703-01 Repeater
Fuse GMA 1.0A 250V
Power Supply
Cable Repeater PCB
0159-00-0055-12
0014-00-0254-01
0670-00-0776-01
0998-00-0191-XX (Telepack 608)
Cap, Battery
O-ring (0.756 inch ID)
Tether
Cover, Serial Port
0380-00-0492-01
0354-02-0018
0380-00-0491-01
0380-00-0477
0040-00-0361-XX (Instrument Radio)
Flexible Antenna
O-Ring .5 inch ID
Note:
0040-00-0361-01
0040-00-0361-02
0992-00-1003
0354-02-0020
Compatible with Panorama Software 8.2.7 and below
Compatible with Panorama software 8.3 and above
WMTS Antenna Network components
Panorama Active antenna
0998-00-0202-02
Telepack Patient Cables and Lead Wires
3-6
Panorama™ Service Manual
Description
Part Number
3 Wire Patient Cable (Domestic) (Snap)
5 Wire Patient Cable (Domestic) (Snap)
V (Brown) Lead (Snap)
RA (White) Lead (Snap)
LL (Red) Lead (Snap)
LA (Black) Lead (Snap)
RL (Green) Lead (Snap)
Lead wire Plug
0012-00-1503-05
0012-00-1503-02
0012-00-1527-11
0012-00-1527-12
0012-00-1527-13
0012-00-1527-14
0012-00-1527-15
0012-00-1527-31
5 Wire Patient Cable 18” (Pinch)
5 Wire Patient Cable 24” (Pinch)
5 Wire Patient Cable 36” (Pinch)
3 Wire Patient Cable 18” (Pinch)
3 Wire Patient Cable 24” (Pinch)
3 Wire Patient Cable 36” (Pinch)
0012-00-1514-01
0012-00-1514-02
0012-00-1514-03
0012-00-1514-04
0012-00-1514-05
0012-00-1514-06
Disposable Lead wire sets
5 Wire Patient Cable 24” snap (box of 20)
3 Wire Patient Cable 24” snap (box of 20)
040-000746-01
040-000748-01
Panorama Spare parts and accessories
Telepack 608 Programming Kit
Telepack programming cable
3.3 volt DC power supply
Instrument Radio 608 Programming Kit
Inst Radio programming cable
5.0 volt DC power supply
Mouse, PS/2
Keyboard, PS/2
AC Power Cord (110V Domestic)
Patch Cable, CAT5e 6’ straight pinned
Patch Cable, CAT5e 10’ straight pinned
Patch Cable, CAT5e 10’ cross over
Cable, audio 3.5mm stereo 6’
Cable, 9 pin serial M/F (touch screen interface)
0020-00-0485-01
0012-00-1521-01
0014-00-0066-01
0020-00-0486-01
0012-00-1541-01
0014-00-0066-10
0992-00-0233-01
0992-00-0108
0012-25-0001
0012-00-1274-01
0012-00-1274-07
0012-00-1392-05
0012-00-1310
0012-00-1306-10
KVM Extender
Longview Companion (Kit)
Longview Power Supply
Panorama™ Service Manual
0992-00-0150-03
0014-00-0227-01
3-7
LCD Monitors
Description
Part Number
19 inch ELO model 1928L Touch Desk mount
19 inch ELO model 1928L Touch Wall mount
0160-00-0092-03
0160-00-0092-04
19 inch ELO model 1928L Non Touch Desk Mount
19 inch ELO model 1928L Non Touch Wall Mount
0160-00-0093-03
0160-00-0093-04
LCD Monitor Power Supplies
18 Inch ELO models 1820 and 1825
19 inch ELO models 1926L and 1928L
0014-00-0058
0014-00-0076
SpO2 Module
Description
Part Number
SpO2 Module (no cables)
Sensor Starter kit
Re-usable Sensor (Ninon)
Disposable Sensor interface cable
Disposable Sensor (10 pack)
0998-00-0192-01
0020-00-0167
0600-00-0140-01
0012-00-1542-01
0600-00-0139-10
SpO2 Module Spare Parts
Button, Latch
Dust Cover
Spring
3-8
0380-00-0487
0380-00-0477
0214-00-0265
Panorama™ Service Manual
4.0 Calibration
There is no internal calibration for Panorama ® Central Station components.
Panorama™ Service Manual
4-1
This page intentionally left blank.
4-2
Panorama™ Service Manual
5.0 Preventative Maintenance
5.1 Display Monitors ............................................................................................................... 5 - 2
5.2 Central Station, Gateways, Telemetry Server and Wireless Transceiver .......................... 5 - 3
5.3 Uninterruptible Power Supplies (UPS) .............................................................................. 5 - 3
5.4 Central Station Network Equipment Racks ....................................................................... 5 - 4
5.5 System Maintenance Schedule ......................................................................................... 5 - 4
Panorama™ Service Manual
5-1
5.1 Display Monitors
The monitor panel and housing should be cleaned by the user as required,
NOTE: Never use an abrasive glass cleaner containing highly concentrated ammonia and strong base
chemicals since they damage the surface treatment.
WARNING: Do not clean the monitor while it is turned on and/or plugged in.
5.1.1 LCD Display Chassis
WARNING: Do not clean the monitor while it is turned on and/or plugged in.
WARNING: Do not spray any cleaner directly on a display. It could possibly leak inside the unit and
cause damage.
Clean the chassis with a lightly moistened soft cloth.
5.1.2 Care and Cleaning of the Screen/Touchscreen
For the best performance, it is recommended that the touch screen on the Panorama display(s) be kept clean.
You can use any standard glass cleaner to clean the screen. Use a cloth or towel to apply the cleaner. Glass
cleaner sprayed directly on a display could possibly leak inside a non-sealed unit and cause damage. Remove
fingerprints and stains by using a liquid lens cleaner and a soft cloth.
To prevent scratches on the front panel of the display screen, observe the following precautions when cleaning:
DO NOT spray any liquids directly on the screen
DO NOT use abrasive cleaning materials to clean a touch screen.
DO NOT wipe a dry screen.
DO NOT use alcohol or chlorinated hydrocarbon solvents.
Use a fine soft-hair brush to carefully brush away dust and dirt particles.
Use a soft cloth moistened with cleaner solution to wipe the touch screen clean.
5- 2
Panorama™ Service Manual
5.2 Central Station Chassis, Gateways, Telemetry Server Chassis and Wireless Transceiver
The external cleaning procedures should only be performed by a qualified electronic technician.
5.2.1 Cleaning
Use an anti-static vacuum to carefully remove accumulated dust, dirt, and lint from the various external surface
areas. Be careful not to dislodge components, or connectors.
5.2.2 Visual Inspection
Perform a visual check to verify that dust, dirt, and lint has been completely removed, and all connectors are
secured and all fans are operational.
5.3 Uninterruptible Power Supplies (UPS)
5.3.1 Rack Mounted UPS
The battery is designed to last for three (3) to five (5) years under normal use. The UPS performs a self-test
automatically every two (2) weeks. If the test fails, the battery LED on the front panel of the UPS will be
illuminated. If this occurs, replace the battery cartridge.
Refer to the UPS manufacturer’s website for replacement battery cartridge specifications. Instructions for
battery replacement are included with the replacement battery cartridge.
Mindray does not supply replacement battery cartridges for the UPS.
5.3.2 Desktop and Auxiliary UPS
Under normal conditions, the original battery in the UPS will last several years. Each UPS has a self test
function to determine the status of the internal battery.
5.3.2.1UPS Model OmniVS800
To run a self-test, leave connected equipment on. With the UPS plugged in and ON, press and hold the button
until the UPS beeps (about 2 seconds) then release it. If the batteries are weak, the “Replace Battery” LED will
stay lit and the UPS will continue to beep after the test.
Refer to the UPS manufacturer’s website for replacement battery specifications.
Instructions for battery replacement are included with the replacement battery cartridge.
5.3.2.2 UPS Model ECO750
To run a Self-Test leave connected equipment on. With the UPS plugged in and turned on, press and hold the
ON/OFF/TEST button for three seconds. *The alarm will beep once briefly after one second has passed. If the
OVERLOAD/CHECK BATTERY LED flashes following a UPS self-test, it may indicate that the battery needs to
be replaced.
Refer to the UPS manufacturer’s website for replacement battery specifications.
Instructions for battery replacement are included with the replacement battery.
Panorama™ Service Manual
5-3
5.4 Central Station Network Equipment Racks
Use an anti-static vacuum to carefully remove accumulated dust, dirt, and lint from the various external surface
areas. Be careful not to dislodge components, or connectors.
Verify the mechanical integrity of all cables, wires, and network connections. Replace any frayed or kinked
cables.
5.5 System Maintenance Schedule
5.5.1 Preventative/Periodic Maintenance
The Preventative Maintenance for the Panorama Patient Monitoring Network will consist of periodic cleaning,
inspection and testing.
Network Components such as Ethernet switches, KVM switches and extenders, Antennas, and Wireless Access
points have no preventative maintenance requirements.
Telemetry Packs do not require any preventative maintenance requirement other than cleaning. Refer to
Sections 10 and 11 of the Operators Manual for cleaning and testing instructions.
Use the following tables for each maintenance procedure:
Central Station and Telemetry Server and Equipment Rack
Activity Area
Cooling fans
Power Supply
Fans
Connections
Cases
Action
Clean
Clean
Clean
Inspect
Inspect
Technical Level
BioMed/CE
BioMed/CE
BioMed/CE
BioMed/CE
BioMed/CE
UPS Batteries
Test
BioMed/CE
5- 4
Method
Forced air
Forced air
Forced air
See section 5.3
(above)
Schedule
Annually
Annually
Annually
Annually
Annually
Annually
Panorama™ Service Manual
6.0 Equipment Configuration
6.1 Introduction ....................................................................................................................... 6 - 2
6.1.1 Configuring the Telemetry Server .................................................................................. 6 - 2
6.1.2 Wired Bedside Monitor Communication Configuration ................................................... 6 - 3
6.1.3 Passport2 and Spectrum WMTS configuration .............................................................. 6 - 7
6.1.4 Mindray 2.4 GHz monitor configuration .......................................................................... 6 - 8
Panorama™ Service Manual
6-1
6.1
Introduction
This section of the manual covers individual component configuration for the Panorama Patient Monitoring
Network.
6.1.1 Configuring the Telemetry Server





Turn on the wireless transceiver.
Turn on the Telemetry Server and display(s).
Enter the Telemetry Server into the Maintenance Mode:
Hold down the SHIFT key on the keyboard when the Windows banner is displayed on the monitor. Do
not release the SHIFT key until the password Logon screen displays on the monitor.
NOTE: The Panorama Server boots into its regular operating mode if no keys are held during the
system reboot.
The Login information for the Panorama Server's password screen is:
LOGON INFORMATION
User Name
swadmin
Password
dscpswadmin
NOTE: If the login information is incorrectly entered, the Windows login failure is displayed.
The Panorama Telemetry Server's Registry Editor Dialog box is displayed if the username/password has been
entered correctly. Press the OK button to close the Registry Editor Dialog box and enter the Panorama Server
configuration mode.
Click on the CB Config Icon. The System Configuration Window will open.
Wireless Telemetry Configuration
ELAN IP Address
 Assign the Server an appropriate ELAN IP Address (7.6.6.XXX). Verify that no other device (Central
Station, beside monitors, Telemetry Server, or Ethernet Switch) being assigned to the network has the
same ELAN IP Address.
WELAN IP Address
Enabling 608 MHz WMTS
 Check the option to enable the WMTS Telemetry. 608 MHz WMTS Configuration
 Select the 608 Band to be used.
 Deselect any unusable frequencies.
 Select the downlink RF pair to be used.
 Select the Global TIM ID and the TIM ID to be used.
6- 2
Panorama™ Service Manual
Saving the Configuration





6.1.2
After setting the IP addresses press the Save and Exit button. After a few seconds, a confirmation
window appears.
Press the YES button to save the settings. The system should reboot at this point. If not,
Press the Start button in the lower left corner of the screen.
Select Shutdown. Select the Shutdown the Computer option.
Press the Yes button to shut down the Server.
Wired Bedside Monitor Communication Configuration
In order to communicate to the Panorama Central Station, a bedside monitor must be configured for
Ethernet protocol and have an IP Address and Subnet Mask address assigned to it. Each bedside
monitor must have a different IP address: 7.6.6.3, 7.6.6.4, etc.
NOTE: The first 3 octets (X.X.X.) must match the IP address of the ELAN address of the Central
Station Network.
Passport2, Spectrum, and Spectrum OR
FIGURE 6-1







Enter the Installation Menu by pressing and holding the Discharge key during power up. Release the
Discharge key when the Installation Menu appears.
Set WMTS Enable to No.
Go to the System Information Sub-Menu.
Set Enable Network to Wired.
Enter an IP Address that matches the Patient Network IP Address scheme (e.g., 7.6.6.3). Do not
duplicate an existing assigned IP address.
Set the Subnet Mask ID to 255.255.255.0.
Check the Device ID number. This number will be entered into the Central Station's equipment list.
Panorama™ Service Manual
6-3

Make sure neither serial port is set to:
VISA with Admit, or PatientNet


Save the information by pressing Save Current.
Turn off the monitor.
PassportV
FIGURE 6-2










6- 4
Enter the Installation Menu by pressing and holding the Discharge key during power up. Release the
Discharge key when the Installation Menu appears.
Go to the Advanced Installation Setup Menu.
Set Enable Network to Wired
Set Connect to Central Station to Yes
Enter an IP Address that matches the Patient Network IP Address scheme (e.g., 7.6.6.3). Do not
duplicate an existing assigned IP address.
Set the Subnet Mask ID to 255.255.255.0.
Check the Device ID number. This number will be entered into the Central Station's equipment list.
Select Previous Menu
Save the information by pressing Save Current. Press Yes to save the settings.
Turn off the monitor.
Panorama™ Service Manual
DPM 6 and 7
FIGURE 6-3




Enter the Main menu.
Select Maintenance then select Factory Maintenance (enter the Passcode 332888)
Verify the Central Station type is set to Panorama
Go to User Maintenance and the select Network Setup
FIGURE 6-4



Verify it is set to LAN
Enter an IP Address that matches the Patient Network IP Address scheme (e.g., 7.6.6.3) and press
Enter, then press OK
Exit back to the normal screen
Panorama™ Service Manual
6-5
V Series Monitors




Press the Setup button on the V Series monitor’s screen
Press the System button, enter the passcode: system and press Enter
Press the Network Tab
Check the Device ID number. This number will be entered into the Central Station's equipment list.
FIGURE 6-5


Press the Wired button. Enter an IP Address that matches the Patient Network IP Address scheme
(e.g., 7.6.6.3). Do not duplicate an existing assigned IP address.
Set the Subnet Mask ID to 255.0.0.0.
FIGURE 6-6


6- 6
Press the Accept button. Press the Accept button again to get back to the main screen.
Re-boot the V series monitor.
Panorama™ Service Manual
6.1.3 Passport2 and Spectrum WMTS wireless connection
FIGURE 6-7








Enter the Installation Menu by pressing and holding the Discharge key during power up. Release the
Discharge key when the Installation Menu appears.
Set WMTS Enable to Yes. If not available for activation, go to the System Information Sub-Menu.
Set Enable Network to No.
Go back to the System Information Sub-Menu.
Set WMTS Enable to Yes.
Make sure neither serial port is set to:
VISA with Admit, or PatientNet
Save the information by pressing Save Current.
Turn off the monitor.
Panorama™ Service Manual
6-7
6.1.4 Mindray 2.4 GHz 802.11b/g wireless connection
PassportV (with internal wireless adapter installed)
Note The PassportV must have the internal wireless card configured with a specific file in order to communicate
to the Mindray 2.4 GHz wireless network. Contact Mindray North America’s Technical Services group for more
information.
FIGURE 6-8







6- 8
Turn off the Passport V.
Press and hold the Discharge key on the front panel while powering up the monitor.
Release the Discharge key when the Installation Menu is displayed.
Rotate the Navigator Knob to navigate and select the Advanced Installation Setup Menu.
Set Enable Network to Wireless
Set Connect to Central Station to Yes
Go to Previous Menu. Select Save Current
Panorama™ Service Manual
DPM6 (with internal wireless adapter installed)
Note: The DPM6 must have the internal wireless card configured by a specific file in order to communicate to
the Mindray 2.4 GHz wireless network. Contact Mindray North America’s Technical Services group for more
information.


Enter the Main menu.
Select Maintenance then select Factory Maintenance (enter the Passcode 332888)
FIGURE 6-9


Verify the Central Station type is set to Panorama
Go to User Maintenance and then select Network Setup
FIGURE 6-10
Panorama™ Service Manual
6-9


Enter the Main menu.
Verify that the Wireless AP Module is checked.
FIGURE 6-11
Go to User Maintenance and then select Network Setup


Verify it is set to Wireless AP
Enter an IP Address that matches the Patient Network IP Address scheme (e.g., 7.6.6.3) and press
Enter then press OK
FIGURE 6-12

6- 10
Exit back to the Monitor’s normal screen
Panorama™ Service Manual
7.0 Appendix A
7.1 Panorama Motherboard CMOS Setup/Verification .......................................................... 7 - 2
7.1.1 Central Station ViewStation WorkStation (0998-00-0701-01, 0998-00-0705-01) ........... 7 - 3
7.1.2 2U Telemetry Server (0998-00-0206-10) ....................................................................... 7 - 6
7.1.3 RM/VM Central Station, ViewStation, WorkStation and Gateway (0998-00- 0708-01,
0998-00-0709-01) ............................................................................................................ 7 - 9
7.1.4 Telemetry Server (0998-00-0710-01) ............................................................................. 7 - 13
7.1.5 e-Gateway (0998-00-0708-03, 0998-00-0709-03) ......................................................... 7 - 16
Panorama™ Service Manual
7-1
7.1
Panorama Motherboard CMOS Setup/Verification
Verify that the VGA and Serial cables are connected between the display(s) and the Central Stat ion. Connect
the keyboard and mouse to the Central Station.
Place each of the monitor power switches to the ON position. Press and release the Central Station's front
panel power switch. Verify that the two LEDs on the front panel are illuminated during the boot-up process. The
power LED (green) should be lit continuously. The HD LED (red) will only be lit continuously during the boot -up
process and then it will only be lit during hard disk reads.
While the Central Station is performing the memory test, press the DELETE key on the keyboard to enter the
CMOS Setup menu. Follow the on-screen instructions to move through the menus and setup or verify the
CMOS exactly as it appears below. When completed, select SAVE to CMOS and EXIT to enter these settings
into memory.
Use the following pages to determine the proper CMOS settings for each unit
7.1.1 Central Station ViewStation WorkStation (0998-00-0701-01, 0998-00-0705-01)
7.1.2 2U Telemetry Server (0998-00-0206-10)
7.1.3 RM/VM Central Station, ViewStation, WorkStation and Gateway (0998-00- 0708-01, 0998-00-0709-01)
7.1.4 Telemetry Server 0998-00-0710-01
7.1.5 e-Gateway (0998-00-0708-03, 0998-00-0709-03)
7- 2
Panorama™ Service Manual
7.1.1 Central Station (0998-00-0701-01, 0998-00-0705-01)
STANDARD CMOS SETUP
Date (mm:dd:yy)
Time
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
Drive A
Drive B
Video
Halt On
Base Memory
Extended Memory
Total Memory
Set to current Date
Set to current Time
** [ST380021A]
** [ST3200822A]
** [LITE-ON LTR-52246S] (or LTR-52327S)
None
1.44M, 3.5 in.
None
EGA/VGA
All, But Keyboard
640K
1047552K
1048576K
ADVANCED BIOS FEATURES
Virus Warning
Disabled
CPU L1 and L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up Numlock Status
Gate A20 Option
Typematic Rate Setting
X Typematic Rate (chars/Sec)
X Typematic Delay (Msec)
Security Option
APIC Mode
MPS Version Control for OS
OS Select For DRAM>64MB
Report No FDD For WIN 95
Small Logo (EPA) Show
Enabled
Enabled
Floppy
CDROM
HDD-0
Enabled
Disabled
Disabled
On
Fast
Disabled
6
250
Setup
Enabled
1.4
Non-OS2
Yes
Enabled
ADVANCED CHIPSET FEATURES
DRAM timing Selectable
X CAS Latency Time
X Active to Precharge Delay
X DRAM RAS# to CAS# Delay
X DRAM RAS# Precharge
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
By SPD
2.5
7
3
3
Auto
Enabled
Enabled
Panorama™ Service Manual
7-3
Delay Transaction
Delay Prior to Thermal
AGP Aperture Size (MB)
ICH4 LAN
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer
Boot Display
Enabled
16 Min
64
Enabled
Enabled
8 MB
Auto
INTEGRATED PERIPHERALS
On-Chip Primary PCI IDE
IDE Primary Master PI0
IDE Primary Slave PI0
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PI0
IDE Secondary Slave PI0
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
USB Controller
USB 2.0 Controller
USB Keyboard Support
AC97 Audio
Init Display First
IDE HDD block Mode
POWER ON Function
X Hot Key Power On
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
Onboard Parallel Port
Parallel Port Mode
PWRON After PWR-Fail
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
Digital I/O
Enabled
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
Enabled
Enabled
Disabled
Auto
PCI Slot
Enabled
BUTTON Only
Ctrl-F1
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
378/IRQ7
SPP
Off
3E8H
IRQ5
2E8H
IRQ10
Disabled
POWER MANAGEMENT SETUP
ACPI Function
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Modem Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Wake-Up by PCI Card
Enabled
User Defined
V/H Sync+ Blank
Yes
Stop Grant
3
Disabled
Disabled
Instant-Off
50.0%
Disabled
7- 4
Panorama™ Service Manual
Power On by Ring
Resume by Alarm
Primary IDE 0
IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D]#
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
PNP/PCI CONFIGURATIONS
PNP OS Install
Reset Configuration Data
Resources Controlled By
PCI/VGA Palette Snoop
No
Disabled
Auto(ESCD)
Disabled
PC HEALTH STATUS
CPU Warning Temperature
Shutdown Temperature
CPU Fan Failure Warning
Sys. Fan Failure Warning
Aux. Fan Failure Warning
Disabled
Disabled
Enabled
Disabled
Disabled
FREQUENCY/VOLTAGE CONTROL
Auto Detect PCI Clk
Spread Spectrum Modulated
Disabled
Enabled
Panorama™ Service Manual
7-5
7.1.2 2U Telemetry Server (0998-00-0206-10)
STANDARD CMOS SETUP
HARD DISKS
Primary Master
Primary Slave
Secondary master
Secondary Slave
TYPE
AUTO
AUTO
AUTO
AUTO
SIZE
0
0
0
0
CYLS
0
0
0
0
HEAD
0
0
0
0
PRECOMP
0
0
0
0
Drive A
Drive B
1.44 3.5 inch
None
Video
Halt On
Base Memory
Extended Memory
Other Memory
Total Memory
EGA/VGA
All, but keyboard
640K
523264K
384K
524288K
SECTOR
MODE
LBA
LBA
LBA
LBA
BIOS FEATURES SETUP
Virus warning:
CPU Internal Cache
External Cache:
Quick Power On Self Test:
Boot Sequence:
Swap Floppy Drive:
Boot Up Floppy Seek:
Boot Up Numlock Status:
Boot Up System Speed:
Gate A20 Options:
Typematic Rate Setting:
Typematic Rate (Chars/Sec):
Typematic Delay (Msec):
Security Options:
PCI/VGA Palettes Snoop:
Mps Version Control For Os:
Os Select For Dram > 64 Mb:
Video Bios Shadow:
C8000-Cbfff Shadow:
Cc000-Cffff Shadow:
D0000-D3fff Shadow:
D4000-D7fff Shadow:
D8000-Dbfff Shadow:
Dc000-Dffff Shadow:
Mpc Enable:
Mpc Post Boot:
Mpb Baud Rate:
7- 6
Disabled
Enabled
Enabled
Enabled
CD-ROM, C, A
Disabled
Disabled
On
High
Fast
Disabled
6
250
Setup
Disabled
1.4
Non-Os2
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
57.6
Panorama™ Service Manual
CHIPSET FEATURES SETUP
Auto Configuration:
Dram Speed Selection:
Ma Wait State:
EDO Ras# To Cas# Delay:
Fast Ras# To Precharge Time:
EDO Dram Read Burst:
EDO Dram Write Burst:
Dram Data Integrity Mode:
Auto Configuration:
CPU-To-CDI IDE Posting:
System Bios Cacheable:
Video Bios Cacheable:
Video Ram Cacheable:
8 Bit I/O Recovery Time:
16bit I/O Recovery Time:
Memory Hole At 15m-16m:
Passive Release:
Delayed Transation:
AGP Aperture Size (Mb):
SDRAM Ras-To Cas Delay:
SDRAM Ras Precharge Time:
SDRAM Cas Latency Time:
Auto Detect Dimm/Pci Clk:
Spread Spectrum Modulated:
Power Management
Power Management:
Pm Control By Apm:
Video Off Method:
Video Off After:
Modem Use Irq:
Doze Mode;
Standby Mode:
Suspend Mode:
HDD Power Down:
Throttle Duty Cycle:
Zz Active In Suspend:
Vga Active Monitor:
Soft-Off By Pwr-Bttn:
CPU Fan Off In Suspend:
IRQ 8 Break Suspend:
IRQ (3-7, 9-15), NMI:
Primary IDE 0:
Primary IDE 1:
Secondary IDE 0:
Secondary IDE 1:
Floppy Disk:
Serial Port:
Parallel Port:
Panorama™ Service Manual
Enabled
60ns
Slow
3
3
X333
X222
ECC
Enabled
Enabled
Disabled
Disabled
Disabled
1
1
Disabled
Enabled
Enabled
64
Fast
Fast
3
Enabled
0.6% (Cntr)
Setup
Disabled
No
V/H Sync+Blank
Standby
N/A
Disabled
Disabled
Disabled
Disabled
62.5%
Disabled
Enabled
Instant-Off
Enabled
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
7-7
PNP/PCI CONFIGURATION
PNP Os Installed:
Resources Controlled By:
Reset Configuration Data:
IRQ-3 Assigned To:
IRQ-4 Assigned To:
IRQ-5 Assigned To:
IRQ-7 Assigned To:
IRQ-9 Assigned To:
IRQ-11 Assigned To:
PNP OS Installed:
IRQ-12 Assigned To:
IRQ-14 Assigned To:
IRQ-15 Assigned To:
DMA-0 Assigned To:
DMA-1 Assigned To:
DMA-3 Assigned To:
DMA-5 Assigned To:
DMA-6 Assigned To:
DMA-7 Assigned To:
PCI IDE IRQ MAP TO:
PRIMARY IDE INT#:
Secondary IDE INT#:
Used Mem Base Addr:
No
Manual
Disabled
PCI/ISA PnP
CI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
CI/ISA PnP
No
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI/ISA PnP
PCI-AUTO
IDE INT#: A
IDE INT#: B
NA
INTEGRATED PERIPHERALS
IDE HDD Block Mode:
IDE Primary Master PIO:
IDE Primary Slave PIO:
IDE Secondary Master PIO:
IDE Secondary Slave PIO:
IDE Primary Slave UDMA:
IDE Secondary Master UDMA:
IDE Secondary Slave UDMA:
ON-CHIP Primary PCI IDE:
ON-CHIP Secondary PCI IDE:
Onboard PCI SCSI CHIP:
USB Keyboard Support:
Watchdog Timer:
WDT Terminal Value:
Kbc Input Clock:
Onboard FDC Controller:
Onboard Serial Port 1:
Onboard Serial Port 2:
UR2 Mode:
Onboard Parallel Port:
Parallel Port Mode:
Onboard Audio Chip:
7- 8
Enabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Enabled
Enabled
Disabled
Disabled
Disabled
7
8 MHZ
Enabled
3F8/IRQ4
2F8/IRQ3
Standard
378/IRQ7
SPP
Enabled
Panorama™ Service Manual
7.1.3 RM/VM Central Station, ViewStation, WorkStation and Gateway (0998-000708-01, 0998-00-0709-01)
MAIN
System Overview
ID = 986LCD27
Build Date = 02/05/08
PCB ID = 10
ADVANCED
CPU Configuration
- Execute Disable Bit =
- Vanderpool Technology =
- Intel (R) SpeedStep (tm) tech. =
Enabled
Enabled
Automatic
IDE Configuration
With IDE CDROM
- ATA/IDE Configuration =
- Configure SATA as =
- Configure SATA Channels =
- Primary IDE Master =
- Primary IDE Slave =
- Secondary IDE Master =
- Secondary IDE Slave =
- Third IDE Master =
With SATA CDROM
Enhanced
ATA/IDE Configuration= Compatible
IDE
Legacy Channels = SATA only
Before PATA
Hard Disk
Not Detected Primary IDE Slave = Atapi CD ROM
Hard drive
Not Detected
Atapi CD ROM Third IDE Master = Not Detected
- Third IDE Slave =
- Hard Disk Write Protect =
- IDE Detect Time Out (Sec) =
- ATA(PI) 80Pin Cable Detection =
- Staggered Spin-up delay =
Not Detected
Disabled
35
Host & Device
Disabled
LAN Configuration
- ETH1 Configuration (Upper) =
- ETH2 Configuration (Lower) =
Enabled
Enabled
FW/IEEE 1394 Configuration
- FW/IEEE 1394 Configuration =
Panorama™ Service Manual
Disabled
7-9
SuperIO Configuration
- Serial Port1 Address =
- Serial Port2 Address =
- Serial Port2 Mode =
- Parallel Port Address =
- Parallel Port Mode =
- Parallel Port IRQ =
- Serial Port3 Address =
- Serial Port3 IRQ =
- Serial Port4 Address =
- Serial Port4 IRQ =
3F8/IRQ4
2F8/IRQ3
Normal
378
Normal
IRQ7
3E8
IRQ11
2E8
IRQ10
Hardware Health Configuration
- Fan Cruise Control =
- Fan Cruise Control =
- Fan Cruise Control =
- Watchdog Function =
Disabled
Disabled
Disabled
Disabled
ACPI Configuration
- Suspend Mode =
- Repost Video on S3 Resume =
- ACPI Version Features =
- USB Device Wakeup From S3/S4 =
S3 (STR)
No
ACPI v1.0
Disabled
APM Configuration
- Power Management/APM =
- Video Power Down Mode =
- Hard Disk Power Down Mode =
- Suspend Time Out =
- PS/2 Kbd/Mouse S4/S5 Wake =
- Keyboard Wake Hotkey =
- Power Button Mode =
- Resume On Ring =
- Resume On PME# =
- Resume On RTC Alarm =
Enabled
Suspend
Suspend
Disabled
Disabled
Any Key
On/Off
Disabled
Disabled
Disabled
PCI Express Configuration
- Active State Power-Management =
Disabled
Remote Access Configuration
- Remote Access =
Disabled
USB Configuration
- Legacy USB Support =
- USB 2.0 Controller Mode =
7- 10
Enabled
HiSpeed
Panorama™ Service Manual
PCIPNP
- Plug & Play O/S =
- Allocate IRQ to PCI VGA =
No
Yes
BOOT
Boot Settings Configuration
- Quick Boot =
- Quiet Boot =
- AddOn ROM Display Mode =
- Bootup Num-Lock =
- PS/2 Mouse Support =
- Wait For 'F1' If Error =
- Hit 'DEL' Message Display =
- Lock Keyboard before OS boot =
- Allow F11 popup =
- Interrupt 19 Capture =
- Execute OEM extension =
- Default init boot order =
- Force boot Device =
Enabled
Disabled
Force BIOS
Off
Auto
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
0->4->3->5->2->1
Disabled
Boot Device Priority
With IDE CDROM
With SATA CDROM
1st Boot Device = 3M-TEAC CD-W552GB **
2nd Boot Device = PM-ST3160815AS **
3rd Boot Device = SM-ST3250410AS **
1st Boot Device PS-ATAPI iHAS5424B **
2nd Boot Device = PM-ST3160815AS **
3rd Boot Device = SM-ST3250410AS **
** Dependent on model number of drive installed in unit
Security
- Boot Sector Virus Protection =
Disabled
CHIPSET
North Bridge Configuration
- Boots Graphic Adapter Priority =
- Internal Graphics Mode Select =
- PEG Port =
- PEG Force x1 =
PEG/PCI
Enabled, 8MB
Auto
Disabled
Video Function Configuration
- DVMT Mode Select =
- DVMT/FIXED Memory =
- Boot Type =
- Backlight Signal Inversion =
- LCDVCC Voltage =
- LVDS =
- SDVO =
DVMT Mode
128MB
CRT+CRT2
Disabled
3.3V
None
CRT
Panorama™ Service Manual
7 - 11
South Bridge Configuration
- USB Functions =
- USB 2.0 Controller =
- Audio controller =
- Audio Jack Sensing =
- SMBUS Controller =
- Restore on AC Power Loss =
8 USB Ports
Enabled
Enabled
Auto
Enabled
Last State
EXIT
Halt on invalid Time/Date =
Secure CMOS =
7- 12
Enabled
Enabled
Panorama™ Service Manual
7.1.4 Telemetry Server (0998-00-0710-01)
MAIN
System Overview
ID = 986LCD27
Build Date = 02/05/08
PCB ID = 10
ADVANCED
CPU Configuration
- Execute Disable Bit =
- Vanderpool Technology =
- Intel (R) SpeedStep (tm) tech. =
IDE Configuration
With IDE CDROM
- ATA/IDE Configuration =
- Configure SATA as =
- Configure SATA Channels =
- Primary IDE Master =
- Primary IDE Slave =
- Secondary IDE Master =
- Secondary IDE Slave =
- Third IDE Master =
- Third IDE Slave =
- Hard Disk Write Protect =
- IDE Detect Time Out (Sec) =
- ATA(PI) 80Pin Cable Detection =
- Staggered Spin-up delay =
Enabled
Enabled
Automatic
With SATA CDROM
Enhanced
ATA/IDE Configuration= Compatible
IDE
Legacy Channels =
SATA only
Before PATA
Before PATA
Hard Disk
Hard Disk
Not Detected
ATAPI CD ROM
Not Detected
Not Detected
Not Detected
Not Detected
ATAPI CD ROM
Not Detected
Disabled
35
Host & Device
Disabled
LAN Configuration
- ETH1 Configuration (Upper) =
- ETH2 Configuration (Lower) =
Enabled
Enabled
FW/IEEE 1394 Configuration
- FW/IEEE 1394 Configuration =
Disabled
SuperI/O Configuration
- Serial Port1 Address =
- Serial Port2 Address =
- Serial Port2 Mode =
- Parallel Port Address =
- Parallel Port Mode =
- Parallel Port IRQ =
- Serial Port3 Address =
- Serial Port3 IRQ =
- Serial Port4 Address =
- Serial Port4 IRQ =
3F8/IRQ4
2F8/IRQ3
Normal
378
Normal
IRQ7
3E8
IRQ11
2E8
IRQ10
Panorama™ Service Manual
7 - 13
Hardware Health Configuration
- Fan Cruise Control =
- Fan Cruise Control =
- Fan Cruise Control =
- Watchdog Function =
Disabled
Disabled
Disabled
Disabled
ACPI Configuration
- Suspend Mode =
- Repost Video on S3 Resume =
- ACPI Version Features =
- USB Device Wakeup From S3/S4 =
S3 (STR)
No
ACPI v1.0
Disabled
APM Configuration
- Power Management/APM =
- Video Power Down Mode =
- Hard Disk Power Down Mode =
- Suspend Time Out =
- PS/2 Kbd/Mouse S4/S5 Wake =
- Keyboard Wake Hotkey =
- Power Button Mode =
- Resume On Ring =
- Resume On PME# =
- Resume On RTC Alarm =
Enabled
Suspend
Suspend
Disabled
Disabled
Any Key
On/Off
Disabled
Disabled
Disabled
PCI Express Configuration
- Active State Power-Management =
Disabled
Remote Access Configuration
- Remote Access =
Disabled
USB Configuration
- Legacy USB Support =
- USB 2.0 Controller Mode =
Enabled
HiSpeed
PCIPNP
- Plug & Play O/S =
- Allocate IRQ to PCI VGA =
No
Yes
BOOT
Boot Settings Configuration
- Quick Boot =
- Quiet Boot =
- AddOn ROM Display Mode =
- Bootup Num-Lock =
- PS/2 Mouse Support =
- Wait For 'F1' If Error =
- Hit 'DEL' Message Display =
- Lock Keyboard before OS boot =
- Allow F11 popup =
- Interrupt 19 Capture =
- Execute OEM extension =
- Default init boot order =
- Force boot Device =
7- 14
Enabled
Disabled
Force BIOS
Off
Auto
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
0->4->3->5->2->1
Disabled
Panorama™ Service Manual
Boot Device Priority
With IDE CDROM
With SATA CDROM
- 1st Boot Device = 3M-TEAC CD-W552GB **
- 2nd Boot Device = PM-ST3160815AS **
PS-ATAPI iHAS5424B **
PM-ST3160815AS **
** Dependent on module number of drive installed in unit
Security
- Boot Sector Virus Protection =
Disabled
CHIPSET
North Bridge Configuration
- Boots Graphic Adapter Priority =
- Internal Graphics Mode Select =
- PEG Port =
- PEG Force x1 =
PEG/PCI
Enabled, 8MB
Auto
Disabled
Video Function Configuration
- DVMT Mode Select =
- DVMT/FIXED Memory =
- Boot Type =
- Backlight Signal Inversion =
- LCDVCC Voltage =
- LVDS =
- SDVO =
DVMT Mode
128MB
CRT+CRT2
Disabled
3.3V
None
CRT
South Bridge Configuration
- USB Functions =
- USB 2.0 Controller =
- Audio controller =
- Audio Jack Sensing =
- SMBUS Controller =
- Restore on AC Power Loss =
8 USB Ports
Enabled
Enabled
Auto
Enabled
Last State
EXIT
Halt on invalid Time/Date =
Secure CMOS =
Panorama™ Service Manual
Enabled
Enabled
7 - 15
7.1.5 e-Gateway (0998-00-0708-03, 0998-00-0709-03)
MAIN
System Overview
ID = 986LCD27
Build Date = 02/05/08
PCB ID = 10
ADVANCED
CPU Configuration
- Execute Disable Bit =
- Vander pool Technology =
- Intel (R) SpeedStep (tm) tech. =
Enabled
Enabled
Automatic
IDE Configuration
With IDE CDROM
with SATA CDROM
- ATA/IDE Configuration =
Enhanced
ATA/IDE Configuration=Compatible
- Configure SATA as =
IDE
Legacy Channels=
SATA only
- Configure SATA Channels = Before PATA
- Primary IDE Master =
Hard Disk
- Primary IDE Slave =
Not Detected Primary IDE Slave =
ATAPI CD ROM
- Secondary IDE Master =
Hard drive
- Secondary IDE Slave =
Not Detected
- Third IDE Master =
Atapi CD ROM Third IDE Master =
Not Detected
- Third IDE Slave =
Not Detected
- Hard Disk Write Protect =
Disabled
- IDE Detect Time Out (Sec) =
35
- ATA(PI) 80Pin Cable Detection =
Host & Device
- Staggered Spin-up delay =
Disabled
LAN Configuration
- ETH1 Configuration (Upper) =
- ETH2 Configuration (Lower) =
Enabled
Enabled
FW/IEEE 1394 Configuration
- FW/IEEE 1394 Configuration =
Disabled
SuperIO Configuration
- Serial Port1 Address =
- Serial Port2 Address =
- Serial Port2 Mode =
- Parallel Port Address =
- Parallel Port Mode =
- Parallel Port IRQ =
- Serial Port3 Address =
3F8/IRQ4
2F8/IRQ3
Normal
378
Normal
IRQ7
3E8
7- 16
Panorama™ Service Manual
- Serial Port3 IRQ =
- Serial Port4 Address =
- Serial Port4 IRQ =
IRQ11
2E8
IRQ10
Hardware Health Configuration
- Fan Cruise Control =
- Fan Cruise Control =
- Fan Cruise Control =
- Watchdog Function =
Disabled
Disabled
Disabled
Disabled
ACPI Configuration
- Suspend Mode =
- Repost Video on S3 Resume =
- ACPI Version Features =
- USB Device Wakeup From S3/S4 =
S3 (STR)
No
ACPI v1.0
Disabled
APM Configuration
- Power Management/APM =
- Video Power Down Mode =
- Hard Disk Power Down Mode =.
- Suspend Time Out =
- PS/2 Kbd/Mouse S4/S5 Wake =
- Keyboard Wake Hotkey =
- Power Button Mode =
- Resume On Ring =
- Resume On PME# =
- Resume On RTC Alarm =
Enabled
Suspend
Suspend
Disabled
Disabled
Any Key
On/Off
Disabled
Disabled
Disabled
PCI Express Configuration
- Active State Power-Management =
Disabled
Remote Access Configuration
- Remote Access =
Disabled
USB Configuration
- Legacy USB Support =
- USB 2.0 Controller Mode =
Enabled
HiSpeed
PCIPNP
- Plug & Play O/S =
- Allocate IRQ to PCI VGA =
No
Yes
BOOT
Boot Settings Configuration
- Quick Boot =
- Quiet Boot =
- AddOn ROM Display Mode =
- Bootup Num-Lock =
Panorama™ Service Manual
Enabled
Disabled
Force BIOS
Off
7 - 17
- PS/2 Mouse Support =
- Wait For 'F1' If Error =
- Hit 'DEL' Message Display =
- Lock Keyboard before OS boot =
- Allow F11 popup =
- Interrupt 19 Capture =
- Execute OEM extension =
- Default init boot order =
- Force boot Device =
Auto
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
0->4->3->5->2->1
Disabled
Boot Device Priority
With IDE CDROM
With SATA CDROM
1st Boot Device = 3M-Teac CD-W552GB **
2nd Boot Device = PM-ST3160815AS **
3rd Boot Device = SM-ST3250410AS **
4th Boot Device = IBA GE SLOT 0408 v
1st Boot Device= PS-Atapi iHAS5424B**
2nd Boot Device = PM-ST3160815AS**
3rd Boot Device = SM-ST3250410AS**
4th Boot Device = IBA GE SLOT 0408 v
** Dependent on model number of drive installed in unit
Security
- Boot Sector Virus Protection =
Disabled
CHIPSET
North Bridge Configuration
- Boots Graphic Adapter Priority =
- Internal Graphics Mode Select =
- PEG Port =
- PEG Force x1 =
PEG/PCI
Enabled, 8MB
Auto
Disabled
Video Function Configuration
- DVMT Mode Select =
- DVMT/FIXED Memory =
- Boot Type =
- Backlight Signal Inversion =
- LCDVCC Voltage =
- LVDS =
- SDVO =
DVMT Mode
128MB
CRT+CRT2
Disabled
3.3V
None
CRT
South Bridge Configuration
- USB Functions =
- USB 2.0 Controller =
- Audio controller =
- Audio Jack Sensing =
- SMBUS Controller =
- Restore on AC Power Loss =
8 USB Ports
Enabled
Enabled
Auto
Enabled
Last State
EXIT
Halt on invalid Time/Date =
Secure CMOS =
7- 18
Enabled
Enabled
Panorama™ Service Manual
8.0 Appendix B
8.1 Programming & configuring replacement Panorama telemetry devices ........................... 8 - 2
8.1.1 Accessing the Wireless Menu ........................................................................................ 8 - 2
8.1.2 Removing Devices from the system ............................................................................... 8 - 2
8.1.3 Programming a replacement Telepack-608 (0998-00-0191-XX) ................................... 8 - 3
8.1.4 Programming the Telepack-608 ..................................................................................... 8 - 4
8.1.5 Programming Replacement Instrument Radios (0040-00-0361-XX) ............................. 8 - 4
8.1.6 Programming the Devices .............................................................................................. 8 - 5
8.1.7 Assigning a replacement Telemetry Device to the Central Station ................................ 8 - 5
8.1.8 Assigning a new Telemetry Device to the Central Station ............................................. 8 - 6
8.1.9 Removing a telemetry device from the Equipment List ................................................. 8 – 6
8.1.10 To re-enter a device after being deleted: ..................................................................... 8 – 6
Panorama™ Service Manual
8-1
8.1 Programming & Configuring Replacement Panorama Telemetry Devices
Each Telemetry device being connected to the system must be programmed prior to assignment to the sys tem.
The programming of the Telepack-608 and Instrument Radio is accomplished in the Central Station's Wireless
menu.
8.1.1






Accessing the Wireless Menu
Perform the following steps to access the Wireless menu.
Select the System Setup button at the bottom of the screen.
Select the Installation Setup tab. A password window will display.
Click on the password window. A keyboard will display.
Type the password “system” and press Enter.
Press the More tab. Press the Wireless tab.
The Programming menu will display (***see diagram below)
FIGURE 8-1
8.1.2
Removing Devices from the system
If the Device ID of the Telemetry Device being replaced is known, it should be removed from the system prior to
programming the replacement device.
8.1.2.1 Telepack-608
 Remove the serial port cover from the bottom of the Telepack. Connect the programming cable (0012 00-1521-01) to the Serial Port on the bottom of the Telepack.
 Install two (2) fresh 1.5 V "AA" batteries in the Telepack. Screw on the battery cap.
 Verify the LA LED illuminates briefly, followed by the RA LED illuminated for approximately 5 seconds.
 Press the Read button. The Device ID, software and hardware versions, and connection status will be
displayed in their respective windows.
 Press the Free Connected Channel button. Press Yes to free the Channel. Press OK to exit.



8- 2
If the Telemetry device is not available, but the device ID is known, use the Free Channel button to
remove it from the system.
Press the Free Channel button. Use the scroll bar to locate the Device ID. Highlight the Device ID and
then press the Free button.
Press Yes to free the ID. Press OK to exit the Free Channel Menu
Panorama™ Service Manual
8.1.2.2 Instrument Radio
 Connect the 9 Pin serial connector of the programming cable (P/N 0012-00-1541-01) to Serial port 1 of
the Central Station. Connect the other end to the Instrument Radio. Connect the external 5.0 volt power
supply to the programming cable. Verify the power supply is plugged into a 110 VAC source.
 Press the Read button. The Device ID, software and hardware versions, and connection status will be
displayed in their respective windows. Press the Free Connected Channel button. Press Yes to free
the Channel. Press OK to exit.
 If the Telemetry device is not available, but the device ID is known, use the Free Channel button to
remove it from the system.
 Press the Free Channel button. Use the scroll bar to locate the Device ID. Highlight the Device ID and
then press the Free button.
 Press Yes to free the ID. Press OK to exit the Free Channel Menu
8.1.3
Programming a replacement Telepack-608 (0998-00-0191-XX)
Programming of a Telepack-608 is done via the programming cable (P/N 0012-00-152101).
NOTE: In order to put the Telepack into the programming mode, the programming cable must be connected to
the serial port on the Telepack prior to applying power to the Telepack. If the connection is broken while
applying power to the Telepack, the sequence must be re-done.
NOTE: Programming of Telemetry Devices must be done on the Central Station that the programming cable is
connected to.



Remove the serial port cover from the bottom of the Telepack.
Connect the serial connector of the programming cable (0012-00-1521-01) to Serial Port 1 on the
Central Station. See the rear panel connection diagrams below for reference.
Connect the programming cable to the Serial Port on the bottom of the Telepack.
Serial Port 1
FIGURE 8-2 Central Station part number s 0998-00-0700-01 and 0998-00-0705-01
Panorama™ Service Manual
8-3
Serial Port 1
FIGURE 8-3 Central Station part numbers 0998-00-0708-01 and 0998-00-0709-01
Install two (2) fresh 1.5 V "AA" batteries in the Telepack. Screw on the battery cap.
Verify the LA LED illuminates briefly, followed by the RA LED illuminated for approximately 5 seconds.
8.1.4






8.1.5
Programming the Telepack-608
Press the Read button. The Device ID, software and hardware versions, and connection status will be
displayed in their respective windows. Verify the Device ID matches the ID on the serial number label of
the Telepack.
If there is an error message in the Connect Window in the programming menu, check the cabling
between the Serial Port 1 on the Central Station to the programming cable, re-power the Telepack and
try again.
Press the Program button. A pop-up window will appear asking if you want to program the telemetry
device. Press the Yes button to program the Telepack.
If the device is programmed successfully, a pop-up window will display: "Wireless device programmed
successfully".
Disconnect the programming cable from the Telepack. Replace the serial port cover to the bott om of
the Telepack. Remove the batteries from the Telepack to remove it from the programming mode.
After being programmed, the Telepack-608 must be assigned to the Central Station equipment list (see
section B.1.7, “Assigning a replacement Telemetry Device to the Central Station.
Programming Replacement Instrument Radios (0040-00-0361-XX)
Note: Systems running 8.1.X and 8.2.X software require instrument radios with C.04 (C.4) or C.09 (C.9)
software installed. Part Number 0040-00-0361-01.
Note: Systems running 8.3.X, and higher require instrument radios with E.02 (E.2) software installed.
Part number 0040-00-0361-02
NOTE: The radio card is static sensitive. Use proper anti-static measures when handling,
programming and installing the radio card.



8- 4
Connect the 9 Pin serial connector of the programming cable (P/N 0012-00-1541-01) to Serial port 1 of
the Central Station.
Connect the other end to the Instrument Radio.
Connect the external 5.0 volt power supply to the programming cable. Verify the power supply is
plugged into a 110 VAC source.
Panorama™ Service Manual
8.1.6



Programming the Devices
Press the Read button. The Device ID, software and hardware versions, and connection status will be
displayed in their respective windows. Record the Device ID number for later reference.
NOTE: If there is an error message in the Connect window in the programming menu, check the 5VDC
power supply and the cabling between the Serial Port 1 on the Central Station to the Instrument Radio
being programmed, and try again.
Select the desired settings for the Downlink (D/L) Pair.
NOTE: On Panorama Systems running 8.1x or 8.2x software, the correct Downlink Pair (DL Pair)
is automatically selected.
NOTE: On Panorama Systems running 8.3 and higher software, the correct Downlink
Pair (DL Pair) must be selected prior to programming the Instrument Radio.






8.1.7
If the DL Pair the system is configured to is known, press the DL Pair button until the desired pair (1, 2
or 3) is displayed. Select Auto if the DL Pair is unknown.
Select the Channel Type. The options are Med and High. Select High if the bedside monitor will be
used with a 12 Lead ECG module. If not being used with a 12 lead module, select Med.
Press the Program button. A pop-up window will appear asking if you want to program the telemetry
device. Press the Yes button to program the Instrument transceiver.
If the device is programmed successfully, a pop-up window will display: "Wireless device programmed
successfully".
Disconnect the power supply from the programming cable. Disconnect the Instrument Radio from the
programming cable.
After being programmed, the Instrument Radio must be assigned to the Central Station equipment list
Assigning a replacement Telemetry Device to the Central Station
The following procedure should be followed when entering a replacement Telepack-608 or Instrument Radio to
the equipment List.
 While in the Wireless menu, press the Previous tab. Press the Equipment Setup tab.
 Select the device to be edited from the displayed list.
 Press the Edit button.
 Press Device ID and then press on the Device ID text box. Enter the new Device ID of the Telepack608 or Instrument Radio being assigned to that tile. Press Enter.
 Press Done to complete the assignment for that device.
 After completion of Device ID assignment, press the Close Menu button.
Panorama™ Service Manual
8-5
8.1.8
Assigning a new Telemetry Device to the Central Station
The following procedure should be followed when entering a new Telepack-608 or Instrument Radio to the
equipment List.
 While in the Wireless menu, press the Previous tab. Press the Equipment Setup tab. Press the New
button.
 Press the Tile button. Select the tile (channel) that the device will be assigned to. Press Done.
 Press the Type button and select the type of device being added. Press Done.
 Press the Label button and then press on the Label text box. Type in a label for the device. Press Enter.
 Press Device ID and then press on the Device ID text box. Enter the Device ID of the Telepack -608 or
Instrument Radio being assigned to that tile. Press Enter. (Maximum of eight characters.)
 Press Done to complete the assignment for the device.
 After completion of Device ID assignment, press the Close Menu button.
8.1.9
Removing a telemetry device from the Central Station's Equipment List
The following procedure should be followed when removing a Telepack-608 or Instrument Radio from the
Equipment List.
Note: You should print out a copy of the equipment list to use as a reference prior to adding or deleting devices
from the equipment list.






Press the System Setup button on the bottom of the screen. Press the Installation Setup button. A
password window will open. Click on the password window and a keyboard will open. Type in the
password system and press Enter.
Press the Previous tab. Press the Equipment Setup tab.
Select (highlight) the device to be removed from the displayed list.
Press the Delete button.
Press Yes when asked if you want to delete the device.
The device is now deleted.
8.1.10 To re-enter a device after being deleted:







8- 6
Press the New button.
Press the Tile button. Select the tile (channel) to be added to.
Press Type button and select the type of device being added.
Press Label button and type a label for the device.
Press Device ID and enter the Device ID of the Telepack or Instrument Radio being assigned to that tile.
Press Enter.
Press Done to complete the assignment for that device.
After completion of Device ID assignment, press the Close Menu button.
Panorama™ Service Manual
9.0 Appendix C
9.1 Connection Diagrams ........................................................................................................ 9 - 3
9.1.1 Central Station ............................................................................................................... 9 – 3
9.1.2 View/Work Station .......................................................................................................... 9 – 4
9.1.3 Telemetry Servers (0998-00-0206-01) ........................................................................... 9 - 5
9.1.4 Wireless Transceiver (0998-00-0710-01) ....................................................................... 9 – 5
9.1.5 Wireless Transceiver ...................................................................................................... 9 - 6
9.1.6 Gateway ......................................................................................................................... 9 - 6
9.1.7 e-Gateway ...................................................................................................................... 9 - 6
9.1.8 KVM Extenders .............................................................................................................. 9 - 7
9.1.9 Laser Printers ................................................................................................................. 9 - 11
9.1.10 Ethernet Switches ........................................................................................................ 9 - 12
Panorama™ Service Manual
9-1
Introduction
This section of the Service manual provides information regarding the interconnection of all
devices on the Panorama Central Station Network
Central Station Installation Configurations
Display Monitors and Laser printers are located at the Nursing station and the Central Station computers and
equipment rack are located away from the nurses’ station.
The following components make up the Panorama Central Monitoring network
 Panorama Central Station(s)
 Panorama View and WorkStations
 Panorama Display Monitor(s)
 HP LaserJet Printer: 4050n/4100n/4200n/4250n/4350n/P4015n/M602
 UPS
 KVM (Keyboard, Video and Mouse) Extender
 24 or 48 Port Ethernet Switches
 CAT5e Patch Cables
 CAT5e Port Patch Panels
 Equipment Rack
608MHz WMTS Telemetry Installation Components







Panorama Telemetry Transceiver
Panorama Wireless Telemetry Server
Antenna Network
Antenna
RG6/RG11 Coax
RF Splitter
Antenna Repeater
The Panorama Wireless Telemetry Server and Telemetry Transceiver are typically located in a remote location
such as an electrical or equipment closet.
The following components are required for the Mindray 2.4 GHz (802.11 b/b Wireless Network



9-2
Access Points
Antenna
CAT 5 Cable (UTP)
Panorama™ Service Manual
9.1 Connection Diagrams
Connection of components
Use the following figures as a reference for the proper component connection to the Central Station.
9.1.1 Central Station
Licensing Key
Mouse
Keyboard C-LAN Programming
Port
Not Used
(VGA)
VGA Monitor 2
Audio
Patient
Network
(E-LAN)
Paging
VGA Monitor 1
Touch
Screen2
(P1)
Touch
Screen1
(PO)
FIGURE 9-1 2U Case (0998-00-0700-01) (Serial Numbers starting with PT)
0 I
Mouse
Keyboard
C-LAN
Programming
Port
License Key
Patient
Network
(E-LAN)
Audio
VGA
Monitor 2
VGA
Monitor 1
Paging
Touch Screen 1
TouchScreen 2
FIGURE 9-2 Vertical Case (0998-00-0705-01) (Serial Numbers starting with EU)
Panorama™ Service Manual
9-3
9.1.2 View/Work Station
VGA
Monitor 2
License Key
Paging
Interface
Central
Network
P0
Serial Port 1 Mouse
C-LAN
Audio
Patient
VGA
Keyboard
Network
Monitor 1
(E-LAN)
P1
Touch
Touch
Screen1 Screen2
(P0)
(P1)
FIGURE 9-3 2U Case (0998-00-0708-01) (Serial Numbers starting with RM)
Serial Port 1
VGA Monitor 1
Mouse
Keyboard
CLAN
Patient
Network
(E-LAN)
Audio Out
VGA Monitor 2
Paging
Interface
License Key
P0
Touch
Screen1
(PO)
P1
Touch
Screen2
(P1)
FIGURE 9-4 Vertical Case (0998-00-0709-01) (Serial Numbers starting with VM)
9-4
Panorama™ Service Manual
9.1.3 Telemetry Server (0998-00-0206-01)
Note: Patient Network connections vary on different hardware and software versions. Refer to the
following diagrams for the correct Patient Network connections.
2.4 Telemetry
(WE-LAN)
Network
Telemetry
Network
Patient
Network
Mouse
Input
Keyboard
Input
Patient
Network
(E-LAN)
LVDS
Cable
Input
VGA
Input
FIGURE 9-4 Software version 5.2.0.X (Serial Numbers starting with WS)
Patient
Network
(E-LAN)
Patient
Network
Telemetry
Network
Mouse
Input
Keyboard
Input
2.4 Telemetry
(WE-LAN)
Network
LVDS
Cable
Input
VGA
Input
FIGURE 9-5 Software versions 5.4.1, 5.4.2, 5.4,4, 5.4.5, and 5.4.6 (Serial Numbers starting with WS)
9.1.4 Telemetry Server (0998-00-0710-01)
TIM PCI Card
VGA
Monitor Mouse
Patient
Keyboard Network (E-LAN)
FIGURE 9-6 Software version 5.4.3 (Serial Numbers starting with TE)
Panorama™ Service Manual
9-5
9.1.5 Wireless Transceiver
Cable to Telemetry
Server TIM PCI card
FIGURE 9-7 Wireless Transceiver rear panel connections
Note: If more than one Telemetry Server is installed, the connection will be to the remaining DS ports.
DS2, DS3 and DS4
Note: DS1 is the master telemetry Server connection and must be connected to an operational Server.
If the master server is offline, the remaining Servers will not be operational.
9.1.6 Gateway
License Key
P0
VGA
Monitor
Mouse Keyboard Hospital
Network
P1
Patient
Network
(E-LAN)
FIGURE 9-8 2U Case (0998-00-0708-01) (Serial Numbers starting with RM-0xxxx-xx)
9.1.7 e-Gateway
Patient
Network
VGA Mouse Keyboard Primary Secondary License key
Hospital Hospital
output
Network Network
FIGURE 9-9 2 U Case (0998-00-0708-03) (Serial Numbers starting with RM-9xxxx-xx)
9-6
Panorama™ Service Manual
VGA
Monitor
Mouse
Keyboard
Primary
Hospital
Network
Secondary
Hospital
Network
Patient
Network
(ELAN)
License Key
FIGURE 9-10 Vertical Case (0998-00-0709-03) (Serial Numbers starting with VM-9xxx-xx)
9.1.8 KVM Extenders (Longview ® Companion)
KVM extenders are used to extend mouse and touch screen control, video, and audio from the Central Station
computer to the Panorama Display monitor via CAT5e cable. Each monitor requires an individual KVM
extender pair (transmitter and receiver).
The maximum length of CAT5e cable for the KVM extender is 400 feet (including any patch cables). Use the
EIA-568B wiring protocol for the CAT5e wiring
Although CAT5e cable is used, it is not an Ethernet device. Do not connect the CAT5e cable to an Ethernet
switch or Ethernet repeater to extend distances.
The KVM transmitter connects to the Panorama Central Station or WorkStation, and the receiver connects to
the display monitor at the nursing station or remote location. Each device requires an external 24 VDC .5A
power supply.
Panorama™ Service Manual
9-7
Transmitter connectors
Transmitter
Front View
L O N G V IE W
Both
Re mote
Loc a l
Audio
N/A (MIC)
Power LED
Mouse
Keyboard
Slide Switch
Transmitter
Local Serial Port
Local VGA Display
Rear View
LOCAL
REMOTE I/O
INPUT
DC Power Input
Serial port
(Touchscreen) DIP Switches
N/A (Mic)
Speakers
Input cable
from Computer
CAT5
Receiver connectors
Receiver
Front View
Power LED
Speaker
N/A (Mic)
Mouse
Keyboard
Receiver
Serial Cable to VGA
Display (Touchscreen)
Rear View
REMOTE I/O
CAT5
DC Power Input
9-8
VGA Display Cable
Panorama™ Service Manual
CONNECTION EXAMPLES
Panorama with a Single Display (up to 12 Channels)
Display Monitor #1
Audio
Cable
Plug in Mouse
& Keyboard
on Front Panel
To Speaker
or Monitor
Audio input
Serial
Cable
RECEIVER
Longview
Receiver
REMOTE I/O
VGA
Cable
24VDC
Power
Supply
CAT5
To Mouse
& Keyboard
inputs on
front panel
TRANSMITTER
REMOTE I/O
INPUT
1 2
3 4 5
6 7
8
Longview
Transmitter
Serial Cable
24VDC
Power
Supply
Audio Cable
To P0
Connector
P0
Cable
Supplied
with KVM
To VGA
Input
KVM
P1
To Mouse
To Keyboard
25 Pin CIFCA
Cable
Note: This example is showing the RM serial number version of the Central Station
Panorama™ Service Manual
9-9
Panorama with Dual Displays (up to 16 channels)
Display Monitor #1
Audio
Cable
Plug in Mouse
& Keyboard
on Front Panel
Display Monitor #2
To Speaker
or Monitor
Audio input
Serial
Cable
Serial
Cable
RECEIVER
Longview
Receiver
RECEIVER
REMOTE I/O
REMOTE I/O
VGA
Cable
24VDC
Power
Supply
VGA
Cable
24VDC
Power
Supply
CAT5
CAT5
To Mouse
& Keyboard
inputs on
front panel
TRANSMITTER
REMOTE I/O
INPUT
1
TRANSMITTER
REMOTE I/O
INPUT
1 2
3 4 5
6 7
8
24VDC
Power
Supply
Longview
Transmitter
2 3 4 5
6
7 8
To VGA2
To P1
Connector
25 Pin
CIFCA
Cable
Serial Cable
24VDC
Power
Supply
Audio Cable
To P0
Connector
P0
Cable
Supplied
with KVM
To VGA
Input
P1
To Mouse
To Keyboard
25 Pin CIFCA
Cable
Monitor 2
Not Used
Monitor 1
KVM
Mouse
Audio
Keyboard
Touch
Screen2
(P1)
Touch
Screen1
(PO)
Not Used
(VGA)
Note: This example is showing the RM serial number version of the Central Station.
The PT serial number version of the central Station is shown for reference.
9 - 10
Panorama™ Service Manual
9.1.9 Laser Printers
Mindray has validated specific HP LaserJet networked printers for use with the Panorama Central Station
network. The drivers for these printers are imbedded in the Panorama’s operating system. Do not try to load
drivers for non-validated printers.
Laser printers are connected to the Panorama Network via the Central Network (CLAN). Laser printers are
assigned an IP address within the Mindray CLAN scheme (7.7.7.XXX)
IP address configuration instructions can be found in the Panorama Printer Installation Guide (0070 -00-0561)
Connection of a laser printer to the Panorama Central Network.

Connect a CAT5e patch cable from the corresponding network jack at the printer location to the
Embedded EIO card or the Jet Direct card on the rear of the Laser Printer.
Connect the network cable to the Jet Direct card
Panorama™ Service Manual
9 - 11
9.1.10 Ethernet Switches
Patient Network (also known as ELAN)
All Patient Monitors, Central Stations, ViewStations, WorkStations, Telemetry Servers, 2.4 GHz Access Points,
Gateways and e-Gateways connect to the Patient Network via the ELAN Switches.
ELAN switches are managed using an IP address within our ELAN scheme (7.6.6.XXX). Switch port settings
need to be configured per the communication protocol requirements for each type of ELAN device
Switch Port Configuration requirements
Device type
ELAN Speed
Central Station
View/WorkStation
Telemetry Server
Gateway/e-Gateway
WebViewer
Passport2/Spectrum
PassportV
DPM6/7
V12/V21
Switch to Switch
802.11g Access Points
Laser Printers
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
ELAN
Duplex
Full
Full
Full
Full
Auto
Auto
Auto
Auto
Full
Auto
Auto
CLAN
Speed
Auto
Auto
CLAN
Duplex
Auto
Auto
Auto
Auto
Note: Failure to connect devices to the properly configured ports on switches can cause problems with the
system’s performance and/or system crashes.
E-LAN Switches (managed)
Mindray has validated and uses the following models:
3COM 5500SI 24 Port
HP 1910V 24 Port
3 COM 5500SI 48 Port
HP1910V 48 port
C-LAN Switches (unmanaged)
CLAN switches are typically unmanaged switches, not requiring an IP address or port configuration.
Mindray has validated and uses the following model:
3COM 2024
9 - 12
Panorama™ Service Manual
0070-00-0634
Rev 6.0
October, 2015
Mindray DS USA, Inc. • 800 MacArthur Boulevard • Mahwah, NJ 07430 • USA •
Dom. Customer Service: 1.800.288.2121 • Intl. Customer Service: +1.201.995.8000 • Dom. Fax:
1.800.926.4275 • Intl. Fax: +1.201.995.8680 • www.mindray.com
Mindray Medical Netherlands B.V.• Drs. W. van Royenstraat 8 • P.O. Box 26 • 3870 CA Hoevelaken
• The Netherlands • Tel: +31 33 25 44 911 • Fax: +31 33 25 37 621
Mindray (UK) Limited • 3 Percy Road • St. John’s Park • Huntingdon • Cambridgeshire PE29 6SZ • United
Kingdom • Tel: 01480 416840 • Fax: 01480 436588
Mindray Medical France SARL • Europarc Créteil •123, Chemin des Bassins •
94035 Créteil Cedex • France • Tel: (0)1.45.13.91.50 • Fax: (0)1.45.13.91.51
Mindray Medical Germany GmbH • Zwischen den Bächen 4 • 64625 Bensheim • Deutschland • Tel:
+49.6251.17524-0 • Fax: +49.6251.17524-20
Mindray Medical International Ltd. • 2813 Office Tower, Convention Plaza • No 1 Harbour Road • Wanchai •
Hong Kong • Tel: +852 2793 5596 • Fax: +852 2344 8824
Medstar Importação e Exportação Ltda • Av. Vereador José Diniz, 3300 • São Paulo, SP • CEP
04804-000 • Brazil • Tel: 55 11 2872-3385 • Fax: 55 11 2872-3385
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement