Timeguard LEDCST_Range Instructions
Advertisement
Advertisement
LED Coastal Grade Floodlight
Model: LEDCST20B (Black)
Model: LEDCST20WH (White)
Model: LEDCST10B (Black)
Model: LEDCST10WH (White)
Model: LEDCST30B (Black)
Model: LEDCST30WH (White)
1
1. General Information
These instructions should be read carefully and retained for further reference and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the luminaire is switched off and the circuit supply fuses are removed or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the installation of this luminaire and install in accordance with the current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this luminaire is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.
3. Technical Specifications
• 230V AC, 50Hz
• These luminaires are of class I construction and must be earthed
• Colour Temperature: 4000K
• Energy Efficiency: class A
• IP55 Rated suitable for restricted external applications
• CE Approved
LEDCST10B-WH
• 10W LED Non replaceable lamp
• Energy Usage:
• Lumen Output:
10Kwh/1000h
750lm
LEDCST20B-WH
• 20W LED Non replaceable lamp
• Energy Usage: 20Kwh/1000h
• Lumen Output: 1500lm
LEDCST30B-WH
• 30W LED Non replaceable lamp
• Energy Usage:
• Lumen Output:
30Kwh/1000h
2250lm
4. Installation
4.1 Mark the position of the mounting holes on the wall using the U bracket supplied as a template.
4.2 Drill the holes for the wall plugs ensuring not to infringe with any gas/water pipes or electrical cables that may be hidden below the surface.
2 4.3 Fix the U bracket to the wall using the correct screws for the wall plugs installed.
4.4 Secure the supply cable into the junction box through the hole(s) provided ensuring that a cable gland, grommet or sealing compound is used to maintain the IP rating of the luminaire.
4.5 Attach the strain relief to the luminaire and screw in ensuring not to over-tighten.
4.6 Terminate the supply cable into the terminal block (please refer to section 5 connection diagram) ensuring correct polarity is observed and that all bare conductors are sleeved.
4.7 Attach the supplied wall plate to the luminaire, apply pressure to catches located on top and bottom until all click into place to ensure the weatherproof seal.
Screws: (M3 x 12mm) x2
3
4.8 Attach the luminaire to the U bracket fitted to the wall, then screw in on both sides ensuring not to over-tighten.
4
5. Connection Diagram
L N
4
MAINS
SUPPLY
L
N
E
ISOLATION
SWITCH
Connect the 3 core mains supply cable to the block on the unit as follows:-
LIVE (Brown or Red) L
NEUTRAL (Blue or Black)
EARTH (Green/Yellow)
N
HELPLINE
020 8450 0515
6. Operation
• Turn the power on to the isolating switch and test for correct operation.
7. Lamp Adjustment
• The lamp can be tilted upwards 45° and tilted downwards 60°.
5 6
6
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge.
For years 2 and 3 or any difficulty in the first year, telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible replacements (where agreed by Timeguard) the customer is responsible for all shipping/postage charges outside of the UK. All shipping costs are to be paid in advance before a replacement is sent.
Model: LEDCST20B (Black)
Model: LEDCST20WH (White)
If you experience problems, do not immediately return the unit to the store. Telephone the Timeguard Customer Helpline;
HELPLINE
020 8450 0515
or email helpline
@
timeguard.com
Qualified Customer Support Co-ordinators will be on-line to assist in resolving your query.
5
For a product brochure please contact:
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112 or email csc
@
timeguard.com
www.timeguard.com
67.058.583 (Issue 2)

Public link updated
The public link to your chat has been updated.
Advertisement