DIGITAL MULTI VRF Service Manual (T1/ R410A

DIGITAL MULTI VRF Service Manual (T1/ R410A
DIGITAL MULTI VRF
Service Manual
(T1/ R410A /50Hz)
GREE ELECTRIC APPLIANCES INC. OF ZHUHAI
GREE COMMERCIAL AIR CONDITION
INVERTER MULTI VRF
CONTENTS
PRODUCT..................................................................................................................................................... 2
1 MODELS LIST .................................................................................................................................. 2
1.1 Outdoor Unit ............................................................................................................................. 2
1.2 Indoor Unit................................................................................................................................ 3
2 NOMENCLATURE ........................................................................................................................... 9
2.1 Nomenclature of Outdoor Unit ................................................................................................. 9
2.2 Nomenclature of Indoor Unit .................................................................................................. 10
3 FUNCTION ...................................................................................................................................... 11
4 PRODUCT DATA ............................................................................................................................ 12
4.1 Product Data of Outdoor Unit ................................................................................................. 12
4.2 Product Data of Indoor Unit.................................................................................................... 17
5 PIPING DIAGRAM......................................................................................................................... 47
CONTROL .................................................................................................................................................. 58
1 OPERATION FLOWCHART ........................................................................................................ 58
1.1 Cooling/Dehumidfying Operation........................................................................................... 59
1.2 Heating Operation ................................................................................................................... 60
2 MAIN LOGIC .................................................................................................................................. 61
2.1 Control Function of Outdoor Unit........................................................................................... 61
2.2 Control Function of Indoor Unit ............................................................................................. 68
3 WIRELESS REMOTE CONTROLLER....................................................................................... 77
4.1 Operation and Display View ................................................................................................... 80
4.2 Dimension ............................................................................................................................... 80
4.3 Installation............................................................................................................................... 81
5 Mini Centralized CONTROLLER ................................................................................................. 82
5.1 Function .................................................................................................................................. 82
5.2 Operation View ....................................................................................................................... 83
5.3 Display View........................................................................................................................... 84
5.4 Connection Between Controller and Unit ............................................................................... 86
6 CENTRALIZED CONTROLLER ................................................................................................. 87
6.1 Function .................................................................................................................................. 87
6.2 Operation View ....................................................................................................................... 87
6.3 Display View........................................................................................................................... 89
6.4 Connection Between Controller and Unit ............................................................................... 90
6.5 Case Study............................................................................................................................... 91
7 MONITORING SOFTWARE ....................................................................................................... 104
7.1 Function ................................................................................................................................ 104
7.2 Connection Between the Computer and the Unit.................................................................. 104
7.3 Hardware............................................................................................................................... 106
INSTALLATION....................................................................................................................................... 114
1 PRECAUTIONS FOR INSTALLATION .................................................................................... 114
1.1 Precautions for Installation ................................................................................................... 114
2 FLOW CHART OF INSTALLATION ......................................................................................... 118
3.1 Hoisting of Unit .................................................................................................................... 119
1
GREE COMMERCIAL AIR CONDITION
INVERTER MULTI VRF
3.2 Selection of Installation Site ................................................................................................. 120
3.3 Dimensions Data ................................................................................................................... 121
3.4 Installation Space Requirements ........................................................................................... 124
3.5 Take Monsoons and Snow into Consideration ...................................................................... 128
4 INSTALLATION OF INDOOR UNIT ......................................................................................... 130
4.1 Duct Type .............................................................................................................................. 130
4.2 Cassette-type Unit ................................................................................................................. 136
4.3 Floor Ceiling Type ................................................................................................................ 144
4.4 Wall mounted type ................................................................................................................ 153
4.5. 1-way cassett type Unit ........................................................................................................ 153
5 INSTALLATION REQUIREMENTS OF REFRIGERANT PIPING ...................................... 157
6 INSTALLATION OF REFRIGERANT PIPING ........................................................................ 161
7 INSTALLATION OF ELECTRONIC EXPANSION VALVE PARTS...................................... 180
8 INSTALLATION OF CONDENSATE PIPE............................................................................... 182
8.1 Material Quality Requirements for Condensate Pipe……………………………………….182
8.2 Key Points for Condensate Pipe Installation……………………………………….……….182
8.3 Installation of Drainage Pipe for Different Types of Indoor Unit ......................................... 185
8.4 Test for Condensate Pipe....................................................................................................... 190
8.5 Requirements of Heat Preservation....................................................................................... 190
9 ELECTRICAL INSTALLATION................................................................................................. 191
9.1 Precautions for Electrical Installation ................................................................................... 191
9.2 Specifications of power cord & circuit breaker..................................................................... 192
9.3 Wiring Sketch Map ............................................................................................................... 192
9.4 Dial-up of Unit ...................................................................................................................... 194
MAINTENANCE ...................................................................................................................................... 199
1 TROUBLE TABLES...................................................................................................................... 199
1.1 Trouble Display of Indoor Unit............................................................................................. 199
1.2 Trouble and State Display of Mainboard LED of Outdoor Unit ........................................... 201
1.3 Trouble Display of Outdoor Unit Transition Board .............................................................. 205
1.4 Trouble Display of Driver Board LED.................................................................................. 206
2 FLOW CHART OF TROUBLESHOOTING.............................................................................. 207
3 WIRING DIADRAM ..................................................................................................................... 214
GMV-R22Td/Na-K,GMV-R28Td/Na-K,GMV-R36Td/Na-K............................................................. 225
4 DISASSEMBLY AND ASSEMBLY PROCEDURE OF MAIN PARTS.................................... 230
4.1Outdoor Unit .......................................................................................................................... 230
4.2 Indoor Unit............................................................................................................................ 242
5 EXPLODED VIEWS AND PART LIST ...................................................................................... 261
5.1 Outdoor Unit ......................................................................................................................... 261
5.2 Exploded View of Indoor Unit and List of Component ........................................................ 273
2
GREE COMMERCIAL AIR CONDITION
DIGITAL MULTI VRF
PRODUCT
1
DIGITAL MULTI VRF
PRODUCT
PRODUCT
1 MODELS LIST
1.1 Outdoor Unit
Units
Series
Capacity
Model
Cooling
Heating
(Btu/h)
(Btu/h)
GMV-R120W/Na-K
Ref
47770
/
GMV-R160W/Na-M
58006
Supply
Appearance
220-240V-
40946
GMVL-R120W/Na-K
Power
1Ph-50Hz
R410A
380-415V-
54594
GMVL-R160W/Na-M
3Ph-50Hz
/
GMV-R260W2/Na-M
97246
88716
GMVL-R260W2/Na-M
/
R410A
GMV-R300W2/Na-M
114310
380-415V3Ph-50Hz
102360
GMVL-R300W2/Na-M
DIGITAL
GMV-R450W3/Na-M
MULTI
VRF
/
163780
153550
GMVL-R450W3/Na-M
R410A
380-415V3Ph-50Hz
/
GMV-R560W4/Na-M
204730
191080
GMVL-R560W4/Na-M
/
R410A
GMV-R600W4/Na-M
214960
380-415V3Ph-50Hz
204730
GMVL-R600W4/Na-M
/
GMV-R860W6/Na-M
307090
293440
GMVL-R860W6/Na-M
/
R410A
GMV-R900W6/Na-M
341210
380-415V3Ph-50Hz
327570
GMVL-R900W6/Na-M
/
Conversion Formula: Btu/h=kW×3412
2
DIGITAL MULTI VRF
PRODUCT
1.2 Indoor Unit
1.2.1 Duct type
Capacity
Model
GMV-R22P/Na-K
GMVL-R22P/Na-K
GMV-R25P/Na-K
GMVL-R25P/Na-K
GMV-R28P/Na-K
GMVL-R28P/Na-K
GMV-R32P/Na-K
GMVL-R32P/Na-K
GMV-R36P/Na-K
GMVL-R36P/Na-K
GMV-R40P/Na-K
GMVL-R40P/Na-K
GMV-R45P/Na-K
GMVL-R45P/Na-K
GMV-R50P/Na-K
GMVL-R50P/Na-K
GMV-R56P/Na-K
GMVL-R56P/Na-K
GMV-R63P/Na-K
GMVL-R63P/Na-K
GMV-R71P/Na-K
GMVL-R71P/Na-K
GMV-R80P/Na-K
GMVL-R80P/Na-K
GMV-R90P/Na-K
GMVL-R90P/Na-K
GMV-R100P/Na-K
GMVL-R100P/Na-K
GMV-R112P/Na-K
GMVL-R112P/Na-K
GMV-R125P/Na-K
GMVL-R125P/Na-K
GMV-R140P/Na-K
GMVL-R140P/Na-K
Cooling
Heating
(Btu/h)
(Btu/h)
7507
8530
9554
10919
12284
13649
15355
17061
19108
21496
24226
27297
30709
34121
38216
42652
47770
Ref
Power
Supply
Appearance
8530
/
10236
/
10918
/
12283
/
13648
/
15354
/
17060
/
19790
/
21496
/
R410A
220-240V1Ph-50Hz
23884
/
27296
/
30026
/
34120
/
37532
/
42650
/
46060
/
51180
/
Conversion Formula: Btu/h=kW×3412
3
DIGITAL MULTI VRF
PRODUCT
Capacity
Model
GMV-R22P/NaB-K
GMVL-R22P/NaB-K
GMV-R28P/NaB-K
GMVL-R28P/NaB-K
GMV-R36P/NaB-K
GMVL-R36P/NaB-K
GMV-R45P/NaB-K
GMVL-R45P/NaB-K
GMV-R56P/NaB-K
GMVL-R56P/NaB-K
GMV-R71P/NaB-K
GMVL-R71P/NaB-K
GMV-R90P/NaB-K
GMVL-R90P/NaB-K
GMV-R112P/NaB-K
GMVL-R112P/NaB-K
GMV-R140P/NaB-K
GMVL-R140P/NaB-K
GMV-R22PS/NaB-K
GMVL-R22PS/NaB-K
GMV-R28PS/NaB-K
GMVL-R28PS/NaB-K
GMV-R36PS/NaB-K
GMVL-R36PS/NaB-K
GMV-R45PS/NaB-K
GMVL-R45PS/NaB-K
GMV-R56PS/NaB-K
GMVL-R56PS/NaB-K
GMV-R71PS/NaB-K
GMVL-R71PS/NaB-K
GMV-R90PS/NaB-K
GMVL-R90PS/NaB-K
GMV-R112PS/NaB-K
GMVL-R112PS/NaB-K
GMV-R140PS/NaB-K
GMVL-R140PS/NaB-K
Cooling
Heating
(Btu/h)
(Btu/h)
7507
9554
12284
15355
19108
24226
30709
38216
47770
7507
9554
12284
15355
19108
24226
30709
38216
47770
Ref
Power
Supply
Appearance
8530
/
10918
/
13648
/
17060
/
21496
/
R410A
220-240V1Ph-50Hz
27296
/
34120
/
42650
/
51180
/
8530
/
10918
/
13648
/
17060
/
21496
/
R410A
220-240V1Ph-50Hz
27296
/
34120
/
42650
/
51180
/
Conversion Formula: Btu/h=kW×3412
4
DIGITAL MULTI VRF
PRODUCT
1.2.2 Cassette type
Capacity
Model
Cooling
Heating
(Btu/h)
(Btu/h)
GMV-R28T/Na-K
(EM503N0091)
9550
GMVL-R28T/Na-K
12280
GMVL-R36T/Na-K
15360
GMVL-R45T/Na-K
17060
GMVL-R50T/Na-K
19100
GMVL-R56T/Na-K
24230
GMVL-R71T/Na-K
GMV-R90T/Na-K
GMVL-R90T/Na-K
GMV-R112T/Na-K
GMVL-R112T/Na-K
30700
38210
42650
R410A
220-240V1Ph-50Hz
21500
27300
34120
/
42650
/
/
R410A
GMV-R140T/Na-K
GMVL-R140T/Na-K
19790
46062
(CM501N0080)
(CM501N0091 )
17060
/
GMV-R125T/Na-K
GMVL-R125T/Na-K
13650
/
GMV-R71T/Na-K
(EM501N0131)
10900
/
GMV-R56T/Na-K
(EM503N0121 )
Appearance
/
GMV-R50T/Na-K
(EM501N0171)
Supply
/
GMV-R45T/Na-K
(EM503N0081 )
Power
/
GMV-R36T/Na-K
(EM501N0151)
Ref
47770
49470
220-240V1Ph-50Hz
/
Conversion Formula: Btu/h=kW×3412
Note: Each model has one or several sets of codes listed in the BOM and the codes inside the brackets are the
product codes of the corresponding model stated in this manual ( as for the model which has only one set of codes
in the BOM, herein they are not covered).
5
DIGITAL MULTI VRF
PRODUCT
Capacity
Model
GMV-R22T/NaA-K
GMVL-R22T/NaA-K
GMV-R28T/NaA-K
GMVL-R28T/NaA-K
GMV-R36T/NaA-K
GMVL-R36T/NaA-K
GMV-R45T/NaA-K
GMVL-R45T/NaA-K
GMV-R22Td/Na-K
GMVL-R22Td/Na-K
GMV-R28Td/Na-K
GMVL-R28Td/Na-K
GMV-R36Td/Na-K
GMVL-R36Td/Na-K
Cooling
Heating
(Btu/h)
(Btu/h)
7506
9550
12280
15360
7506
9550
12280
Ref
Power
Supply
Appearance
8530
/
10900
/
13650
220-240
R410A
V-1Ph-50
Hz
/
17060
/
8530
/
10900
/
13650
220-240
R410A
V-1Ph-50
Hz
/
6
DIGITAL MULTI VRF
PRODUCT
1.2.3 Wall mounted type
Capacity
Model
GMV-R22G/NaB-K
GMVL-R22G/NaB-K
GMV-R28G/NaB-K
GMVL-R28G/NaB-K
GMV-R36G/NaB-K
GMVL-R36G/NaB-K
GMV-R45G/NaB-K
GMVL-R45G/NaB-K
Cooling
Heating
(Btu/h)
(Btu/h)
7507
9554
12284
15355
GMV-R50G/NaB-K
(CM100N0020 )
17061
GMVL-R50G/NaB-K
GMV-R56G/NaB-K
GMVL-R56G/NaB-K
GMV-R22G/NaC-K
GMVL-R22G/NaC-K
19108
7507
9554
GMVL-R28G/NaC-K
12284
GMVL-R36G/NaC-K
GMV-R45G/NaC-K
GMVL-R45G/NaC-K
GMV-R71G/Na-K
GMVL-R71G/Na-K
GMV-R80G/Na-K
GMVL-R80G/Na-K
GMV-R22G/NaG-K
GMVL-R22G/NaG-K
GMV-R28G/NaG-K
GMVL-R28G/NaG-K
GMV-R36G/NaG-K
GMVL-R36G/NaG-K
GMV-R45G/NaG-K
GMVL-R45G/NaG-K
GMV-R50G/NaG-K
GMVL-R50G/NaG-K
GMV-R56G/NaG-K
GMVL-R56G/NaG-K
GMV-R63G/NaG-K
Supply
Appearance
220V
50Hz
10919
/
13649
/
17061
/
19790
21496
/
8530
/
10919
/
GMV-R36G/NaC-K
(EM100N0310 )
/
R410A
Power
/
GMV-R28G/NaC-K
(EM100N0290 )
8530
Ref
13649
/
15355
24226
27297
7507
9554
12284
15355
17061
19108
21496
17061
/
27297
/
30709
/
8530
/
10919
/
13649
/
17061
/
19790
/
21496
/
23885
7
DIGITAL MULTI VRF
PRODUCT
GMVL-R63G/NaG-K
GMV-R71G/NaG-K
GMVL-R71G/NaG-K
/
27297
24226
/
Note: Btu/h=kW×3412
Note: Each model has one or several sets of codes listed in the BOM and the codes inside the brackets are the
product codes of the corresponding model stated in this manual ( as for the model which has only one set of codes
in the BOM, herein they are not covered).
1.2.4Floor ceiling type
Capacity
Model
GMV-R28Zd/Na-K
GMVL-R28Zd/Na-K
GMV-R36Zd/Na-K
GMVL-R36Zd/Na-K
GMV-R50Zd/Na-K
GMVL-R50Zd/Na-K
GMV-R71Zd/Na-K
GMVL-R71Zd/Na-K
GMV-R90Zd/Na-K
GMVL-R90Zd/Na-K
GMV-R112Zd/Na-K
GMVL-R112Zd/Na-K
GMV-R125Zd/Na-K
GMVL-R125Zd/Na-K
Cooling
Heating
(Btu/h)
(Btu/h)
Power
Ref
Appearance
Supply
10919
9554
/
13649
12284
/
19790
17061
/
27297
24226
/
220-240V-
R410A
1Ph-50Hz
34121
30709
/
42652
38216
/
46064
42652
/
Note: Btu/h=kW×3412
Notes: a. Cooling only unit (GMVL type) has no items on heating;
b. Noise was tested in semi-silenced room, so the actual noise value will be a little higher for change of ambient;
c. Nominal capacities are based on the following conditions:
Capacity
Model
Cooling
Heating
(KW)
(KW)
GMV-R71Zd/NaB-K
7.1
8.0
GMV-R90Zd/NaB-K
9
10
Ref
R410A
GMV-R112Zd/NaB-K
11.2
12.5
GMV-R140Zd/NaB-K
12.5
13.5
Power
Appearance
Supply
220-240V1Ph-50Hz
Cooling
Heating
Indoor :27℃(80.6℉)/19℃(66.2℉)
Indoor: 20℃(68℉)/-
Outdoor: 35℃(95℉)/-
Outdoor : 7℃(44.6℉)/6℃(42.8℉)
8
DIGITAL MULTI VRF
PRODUCT
2 NOMENCLATURE
2.1 Nomenclature of Outdoor Unit
GMV
□
1
2
-
R
□
W
*
3
4
5
6
/
Na
-
7
NO.
Description
Options
1
GMV
GREE multi variable
2
Model Code
3
Digital scroll
4
Nominal cooling capacity
5
W
Outdoor unit
6
*
Compressor quantity
7
Refrigerant:
R410A
8
Power complement
□
8
L: Cooling Only
Default: Heat pump
45 represents 4.5kW
Btu/h=kW×3412
M:380-415V-3Ph-50Hz;
K:220-240V-1Ph-50Hz
Example: GMV-R300W2/Na-M, a digital scroll outdoor unit of GREE using R410A refrigerant, with two
compressors and the nominal cooling capacity is 30kw. The power supply is 380-415V-3Ph-50Hz。
9
DIGITAL MULTI VRF
PRODUCT
2.2 Nomenclature of Indoor Unit
GMV
□
1
2
-
R
□
□
3
4
5
/
Na
□
6
7
NO.
Description
Options
1
GMV
GREE multi variable
2
Model Code
3
Digital scroll
4
Nominal cooling capacity
-
□
8
L: Cooling Only
Default: Heat pump
36 represents 3.6kW
Btu/h=kW×3412
G: wall mounted
P: ducted
5
Indoor unit
T: cassette
Zd: floor ceiling
Td=1-way Casstte type
6
Refrigerant:
R410A
7
Design Sequence.
B :Second generation
8
Power complement
M:380-415V-3Ph-50Hz;
K:220-240V-1Ph-50Hz
Example: GMV-R22G/NaB-K. A wall mounted indoor unit of GREE, and the nominal cooling capacity is
2.2kw. It's the second generation product。
10
DIGITAL MULTI VRF
PRODUCT
3 FUNCTION
Auto Restart
Fan Operation Mode
LCD Remote Controller (Option)
Auto Swing Function
For
Ceiling Soiling Prevention
Comfortable
Program Dry
Air Conditioning
High Fan Speed Mode
High Ceiling Application
Two Select Thermo Sensor
Hot Start
Timer Selector
Fresh Air Intake Directly from The Unit
Drain Pump
Long Life Filter
For Easy
Ultra-Long life Filter (Option)
Construction and
Mold Resistant Treatment for Filter
Maintenance
Filter Sign
Mold Resistant Drain Pan
Emergency Operation
Self Diagnoses Function
Set Back Time Clock
Double Remote Control
For Flexible
Control
Group Control By 1 Remote Controller
Control By External Command
Remote/Centralized Control
11
DIGITAL MULTI VRF
PRODUCT
4 PRODUCT DATA
4.1 Product Data of Outdoor Unit
Model
GMV(L)-R120W/Na-K
GMV(L)-R160W/Na-M
kW
12
16
Btu/h
40946
54594
kW
14
17
Btu/h
47770
58006
Noise
dB(A)
58
58
R410A Filling Amount
kg
6
8
Power Supply
V,Ph,Hz
220-240V-1Ph-50Hz
380-415V-3Ph-50Hz
Cooling
kW
3.9
4.9
Heating
kW
3.8
4.8
Cooling
A
21.1
7.8
Heating
A
21.9
8.1
Width
mm
1100
1100
Depth
mm
340
340
Height
mm
1250
1250
Compressor
Digital Scroll×1
Digital Scroll×1
Moisture protection
IP24
IP24
Climate Type
T1
T1
mm
Φ15.9
Φ19.05
Inch
5/8
3/4
mm
Φ9.52
Φ9.52
Inch
3/8
3/8
Connection Method
Flare Connection
Flare Connection
Max. NO. of Indoor Unit
5
7
kW
0.42
0.42
m3/h
6000
6000
CFM
3531
3531
2
2
140/160
140/160
6.0×3
2.5×5
mm
(590+201)×378
(590+201)×378
Width
mm
1260
1260
Depth
mm
450
450
Height
mm
1270
1270
Loading Quantity ( 20’ Container ) ③
unit
21
21
Loading Quantity ( 40’ Container ) ④
unit
46
46
unit
92
92
A
32
16
Cooling①
Capacity
Heating②
Power input
Rated current
Dimensions
Gas Pipe
Connection Pipes
Liquid Pipe
Power input
Fan
Air Flow Rate
Step
Weight(Net/Gross)
Recommended
Power Lines
kg
mm2×No.
Dimensions of Installation
Dimensions of
Package
Loading Quantity ( 40’ High Cube
Container ) ⑤
Circuit breaker
12
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R260W2/Na-M
GMV(L)-R300W2/Na-M
kW
26
30
Btu/h
88716
102360
kW
28.5
33.5
Btu/h
97246
114310
Noise
dB(A)
58
58
R410A Filling Amount
kg
14
14
Power Supply
V,Ph,Hz
380-415V-3Ph-50Hz
380-415V-3Ph-50Hz
Cooling
kW
8.5
9.0
Heating
kW
8.0
8.8
Cooling
A
17.5
18.2
Heating
A
18.2
18.6
Width
mm
990
990
Depth
mm
880
880
Height
mm
1772
1772
Digital Scroll×1 + Constant
Digital Scroll×1
Speed Scroll×1
+ Constant Speed Scroll×1
Moisture protection
IP24
IP24
Climate Type
T1
T1
mm
Φ22.2
Φ22.2
Inch
7/8
7/8
mm
Φ9.52
Φ9.52
Inch
3/8
3/8
Connection Method
Brazing Connection
Flare Connection
Max. NO. of Indoor Unit
12
14
kW
1
1
m3/h
10000
10000
CFM
5886
5886
12
12
280/310
300/330
6.0×5
6.0×5
mm
787(337)×844
787(337)×844
Width
mm
1162
1162
Depth
mm
980
980
Height
mm
1950
1950
Loading Quantity ( 20’ Container ) ③
unit
10
10
Loading Quantity ( 40’ Container ) ④
unit
22
22
unit
22
22
A
32
32
Cooling①
Capacity
Heating②
Power input
Rated current
Dimensions
Compressor
Gas Pipe
Connection Pipes
Liquid Pipe
Power input
Fan
Air Flow Rate
Step
Weight(Net/Gross)
Recommended
Power Lines
kg
mm2×Number
Dimensions of Installation
Dimensions of
Package
Loading Quantity ( 40’ High Cube
Container ) ⑤
Circuit breaker
13
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R450W3/Na-M
GMV(L)-R560W4/Na-M
kW
45
56
Btu/h
153550
191080
kW
48
60
Btu/h
163780
204730
Noise
dB(A)
60
60
R410A Filling Amount
kg
20
25
Power Supply
V,Ph,Hz
380-415V-3Ph-50Hz
380-415V-3Ph-50Hz
Cooling
kW
14.5
18.5
Heating
kW
13.7
18.0
Cooling
A
27.1
34.7
Heating
A
27.5
34.8
Width
mm
1290
1980
Depth
mm
880
920
Height
mm
1772
1760
Digital Scroll×1
Digital Scroll×1
+ Constant Speed Scroll×2
+ Constant Speed Scroll×3
Moisture protection
IP24
IP24
Climate Type
T1
T1
mm
Φ28.6
Φ28.6
Inch
1-1/8
1-1/8
mm
Φ12.7
Φ15.9
Inch
1/2
5/8
Connection Method
Flare Connection
Brazing Connection
Max. NO. of Indoor Unit
16
25
Power input
kW
1
2
m3/h
10000
20000
CFM
5886
11771
12
12
450/490
600/640
10.0×5
16.0×5
mm
1160(850) ×844
(1400±2) (460±2) ×(880±2)
Width
mm
1370
2152
Depth
mm
980
980
Height
mm
1950
1950
Loading Quantity ( 20’ Container ) ③
unit
8
5
Loading Quantity ( 40’ Container ) ④
unit
17
12
unit
17
12
A
40
50
Cooling①
Capacity
Heating②
Power input
Rated current
Dimensions
Compressor
Gas Pipe
Connection Pipes
Fan
Liquid Pipe
Air Flow Rate
Step
Weight(Net/Gross)
Recommended
Power Lines
mm2×Number
Dimensions of Installation
Dimensions of
Package
Loading Quantity ( 40’ High Cube
Container ) ⑤
Circuit breaker
kg
14
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R600W4/Na-M
GMV(L)-R860W6/Na-M
kW
60
86
Btu/h
204730
293440
kW
63
96
Btu/h
214960
307090
Noise
dB(A)
60
62
R410A Filling Amount
kg
25
45
Power Supply
V,Ph,Hz
380-415V-3Ph-50Hz
380-415V-3Ph-50Hz
Cooling
kW
19.2
28.8
Heating
kW
18.2
26.4
Cooling
A
36
50.6
Heating
A
36
46.6
Width
mm
1980
2580
Depth
mm
920
880
Height
mm
1760
1772
Cooling①
Capacity
Heating②
Power input
Rated current
Dimensions
Digital Scroll×1
Compressor
+ Constant Speed Scroll×3
Digital Scroll×1
+ Constant Speed
Scroll×5
Moisture protection
IP24
IP24
Climate Type
T1
T1
mm
Φ28.6
Φ34.9
Inch
1-1/8
1-3/8
mm
Φ15.9
Φ19.05
Inch
5/8
3/4
Connection Method
Brazing Connection
Brazing Connection
Max. NO. of Indoor Unit
27
32
Power input
kW
2
2
m3/h
20000
20000
CFM
11771
11771
12
12
600/640
800/850
16.0×5
35.0×5
Gas Pipe
Connection Pipes
Fan
Liquid Pipe
Air Flow Rate
Step
Weight(Net/Gross)
Recommended Power
Lines
kg
mm2×Number
Dimensions of Installation
(2000±2) (860±2)
mm
(1400±2) (460±2) ×(880±2)
Width
mm
2152
2660
Depth
mm
980
980
Height
mm
1950
1950
Loading Quantity ( 20’ Container ) ③
unit
5
/
Loading Quantity ( 40’ Container ) ④
unit
12
/
unit
12
/
A
50
80
Dimensions of
Package
Loading Quantity ( 40’ High Cube
Container ) ⑤
Circuit breaker
×(844±2)
15
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R900W6/Na-M
kW
90
Btu/h
327570
kW
100
Btu/h
341210
Noise
dB(A)
62
R410A Filling Amount
kg
45
Power Supply
V,Ph,Hz
380-415V-3Ph-50Hz
Cooling
kW
30.1
Heating
kW
27.5
Cooling
A
52.9
Heating
A
48.5
Width
mm
2580
Depth
mm
880
Height
mm
1772
Cooling①
Capacity
Heating②
Power input
Rated current
Dimensions
Compressor
Digital Scroll×1+ Constant Speed Scroll×5
Moisture protection
IP24
Climate Type
T1
Gas Pipe
Connection Pipes
Liquid Pipe
Φ34.9
Inch
1-3/8
mm
Φ19.05
Inch
3/4
Connection Method
Brazing Connection
Max. NO. of Indoor Unit
32
Power input
Fan
mm
Air Flow Rate
kW
2
m3/h
24000
CFM
11771
Step
12
Weight(Net/Gross)
Recommended Power Lines
kg
800/850
mm2×Number
Dimensions of Installation
35.0×5
mm
(2000±2) (860±2) ×(844±2)
Width
mm
2660
Depth
mm
980
Height
mm
1950
Loading Quantity ( 20’ Container ) ③
unit
/
Loading Quantity ( 40’ Container ) ④
unit
/
Loading Quantity ( 40’ High Cube Container ) ⑤
unit
/
Circuit breaker
A
80
Dimensions of Package
① Indoor air temperature: 27①(80.6①)/19①(66.2①)
② Indoor air temperature: 20①(68①)/-
Outdoor air temperature: 35①(95①)/-;
Outdoor air temperature: 7①(44.6①)/6①(42.8①);
③ Interior Dimensions L*W*H: 5898*2352*2393, Door Opening W*H: 2343*2280;
④ Interior Dimensions L*W*H: 12032*2350*2390, Door Opening W*H: 2343*2280;
⑤ Interior Dimensions L*W*H:12032*2350*2697, Door Opening W*H: 2338*2585.
16
DIGITAL MULTI VRF
PRODUCT
4.2 Product Data of Indoor Unit
4.2.1 Duct Type
Model
GMV(L)-R22P/Na-K
GMV(L)-R25P/Na-K
GMV(L)-R28P/Na-K
kW
2.2
2.5
2.8
Btu
7506
8530
9554
kW
2.5
3.0
3.2
Btu
8530
10236
10918
m3/h
450
450
570
CFM
265
265
336
Sound Pressure Level (H/L)
dB(A)
37/33
37/33
39/35
External Static Pressure
Pa
25
25
25
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.02
0.02
0.02
A
0.17
0.17
0.16
mm
Φ9.52
Φ9.52
Φ9.52
inch
Φ3/8"
Φ3/8"
Φ3/8"
mm
Φ6.35
Φ6.35
Φ6.35
inch
Φ1/4"
Φ1/4"
Φ1/4"
Flare Connection
Flare Connection
Flare Connection
mm
Φ20×1.5
Φ20×1.5
Φ20×1.5
mm
875×680×220
875×680×220
875×680×220
mm
1012×708×275
1012×708×275
1012×708×275
kg
27/31
27/31
27/31
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
17
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R32P/Na-K
GMV(L)-R36P/Na-K
GMV(L)-R40P/Na-K
kW
3.2
3.6
4.0
Btu
10919
12284
13649
kW
3.6
4.0
4.5
Btu
12283
13648
15354
m3/h
570
570
840
CFM
336
336
494
Sound Pressure Level (H/L)
dB(A)
39/35
39/35
40/36
External Static Pressure
Pa
25
25
20
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.02
0.02
0.07
A
0.16
0.16
0.69
mm
Φ12.7
Φ12.7
Φ12.7
inch
Φ1/2"
Φ1/2"
Φ1/2"
mm
Φ6.35
Φ6.35
Φ6.35
inch
Φ1/4"
Φ1/4"
Φ1/4"
Flare Connection
Flare Connection
Flare Connection
mm
Φ20×1.5
Φ20×1.5
Φ30×1.5
mm
875×680×220
875×680×220
980×736×266
mm
1012×708×275
1012×708×275
1068×766×320
kg
27/31
27/31
36/39
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
18
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R45P/Na-K
GMV(L)-R50P/Na-K
GMV(L)-R56P/Na-K
kW
4.5
5.0
5.6
Btu
15355
17061
19108
kW
5.0
5.8
6.3
Btu
17060
19790
21496
m3/h
840
840
1400
CFM
494
494
824
Sound Pressure Level (H/L)
dB(A)
40/36
40/36
42/38
External Static Pressure
Pa
40
40
100
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.07
0.07
0.15
A
0.69
0.69
1.32
mm
Φ12.7
Φ12.7
Φ15.9
inch
Φ1/2"
Φ1/2"
Φ5/8"
mm
Φ6.35
Φ6.35
Φ9.52
inch
Φ1/4"
Φ1/4"
Φ3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
980×736×266
980×736×266
1112×756×300
mm
1068×766×320
1068×766×320
1245×785×360
kg
36/39
36/39
55/59
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
19
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R63P/Na-K
GMV(L)-R71P/Na-K
GMV(L)-R80P/Na-K
kW
6.3
7.1
8.0
Btu
21496
24226
27297
kW
7.0
8.0
8.8
Btu
23884
27296
30026
m3/h
1400
1400
1400
CFM
824
824
824
Sound Pressure Level (H/L)
dB(A)
42/38
42/38
42/38
External Static Pressure
Pa
100
100
100
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.15
0.15
0.15
A
1.32
1.32
1.32
mm
Φ15.9
Φ15.9
Φ15.9
inch
Φ5/8"
Φ5/8"
Φ5/8"
mm
Φ9.52
Φ9.52
Φ9.52
inch
Φ3/8"
Φ3/8"
Φ3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
1112×756×300
1112×756×300
1112×756×300
mm
1245×785×360
1245×785×360
1245×785×360
kg
55/59
55/59
55/59
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
20
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R90P/Na-K
GMV(L)-R100P/Na-K
GMV(L)-R112P/Na-K
kW
9.0
10.0
11.2
Btu
30709
34121
38216
kW
10.0
11.0
12.5
Btu
34120
37532
42650
m3/h
2000
2000
2000
CFM
1177
1177
1177
Sound Pressure Level (H/L)
dB(A)
44/40
44/40
44/40
External Static Pressure
Pa
100
100
100
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.225
0.225
0.225
A
2.14
2.14
2.14
mm
Φ15.9
Φ15.9
Φ15.9
inch
Φ5/8"
Φ5/8"
Φ5/8"
mm
Φ9.52
Φ9.52
Φ9.52
inch
Φ3/8"
Φ3/8"
Φ3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
1385×736×300
1385×736×300
1385×736×300
mm
1514×795×360
1514×795×360
1514×795×360
kg
75/79
75/79
75/79
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
21
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R125P/Na-K
GMV(L)-R140P/Na-K
kW
12.5
14.0
Btu
42652
47770
kW
13.5
15.0
Btu
46060
51180
m3/h
2000
2000
CFM
1177
1177
Sound Pressure Level (H/L)
dB(A)
44/40
45/41
External Static Pressure
Pa
100
50
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.225
0.225
Running Current
A
2.14
2.14
mm
Φ15.9
Φ15.9
inch
Φ5/8"
Φ5/8"
mm
Φ9.52
Φ9.52
inch
Φ3/8"
Φ3/8"
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
mm
1385×736×300
1385×736×300
mm
1514×795×360
1514×795×360
kg
75/79
75/79
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation
22
DIGITAL MULTI VRF
PRODUCT
Model
Cooling Capacity
Heating Capacity
Air Flow Rate
Sound Pressure Level
(H/L)
External Static Pressure
GMV(L)-R22P/NaB-K
GMV(L)-R28P/NaB-K
GMV(L)-R36P/NaB-K
kW
2.2
2.8
3.6
Btu
7507
9554
12284
kW
2.5
3.2
4.0
Btu
8530
10918
13648
m3/h
450
570
570
CFM
265
335
336
dB(A)
37/33
39/35
39/35
Pa
50/20
50/20
50/20
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.04
0.06
0.06
A
028
0.41
0.41
mm
φ9.52
φ9.52
φ12.7
inch
3/8"
3/8"
1/2"
mm
φ6.35
φ6.35
φ6.35
inch
1/4"
1/4"
1/4"
Flare Connection
Flare Connection
Flare Connection
mm
φ20×1.5
φ20×1.5
φ20×1.5
mm
880×655×250
880×655×250
880×655×250
mm
1020×745×305
1020×745×305
1020×745×305
kg
27/31
28.5/33.5
28.5/33.5
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
23
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R45P/NaB-K
GMV(L)-R56P/NaB-K
GMV(L)-R71P/NaB-K
kW
4.5
5.6
7.1
Btu
15355
19108
24226
kW
5.0
6.3
8.0
Btu
17060
21496
27296
m3/h
700
1000
1100
CFM
412
589
647
Sound Pressure Level (H/L)
dB(A)
40/36
42/38
42/38
External Static Pressure
Pa
50/20
60/30
60/30
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.07
0.15
0.15
A
0.55
1.3
1.3
mm
Φ12.7
Φ15.9
Φ15.9
inch
1/2"
5/8"
5/8"
mm
Φ6.35
Φ9.52
Φ9.52
inch
1/4"
3/8"
3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
980×721×266
1112×756×300
1112×756×300
mm
1068×766×320
1245×785×360
1245×785×360
kg
34/37
49/56
49/56
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
24
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R90P/NaB-K
GMV(L)-R112P/NaB-K
GMV(L)-R140P/NaB-K
kW
9.0
11.2
14.0
Btu
30709
38216
47770
kW
10.0
12.5
15.0
Btu
34120
42650
51180
m3/h
1700
1700
2000
CFM
1001
1001
1177
Sound Pressure Level (H/L)
dB(A)
44/40
44/40
45/41
External Static Pressure
Pa
80/40
80/40
100/50
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.225
0.225
0.26
A
2.15
2.15
2.67
mm
Φ15.9
Φ15.9
Φ15.9
inch
5/8"
5/8"
5/8"
mm
Φ9.52
Φ9.52
Φ9.52
inch
3/8"
3/8"
3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
1425×736×300
1425×736×300
1463×736×300
mm
1514×785×360
1514×785×360
1555×810×345
kg
62/71
62/71
63.5/73
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
25
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R22PS/NaB-K
GMV(L)-R28PS/NaB-K
GMV(L)-R36PS/NaB-K
kW
2.2
2.8
3.6
Btu
7507
9554
12284
kW
2.5
3.2
4.0
Btu
8530
10918
13648
m3/h
450
570
570
CFM
265
335
336
Sound Pressure Level (H/L)
dB(A)
37/33
39/35
39/35
External Static Pressure
Pa
50/20
50/20
50/20
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.04
0.06
0.06
A
0.28
0.41
0.41
mm
φ9.52
φ9.52
φ12.7
inch
3/8"
3/8"
1/2"
mm
φ6.35
φ6.35
φ6.35
inch
1/4"
1/4"
1/4"
Flare Connection
Flare Connection
Flare Connection
mm
φ20×1.5
φ20×1.5
φ20×1.5
mm
880×655×250
880×655×250
880×655×250
mm
1020×745×305
1020×745×305
1020×745×305
kg
28.5/33.5
30.5/35.5
30.5/35.5
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
26
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R45PS/NaB-K
GMV(L)-R56PS/NaB-K
GMV(L)-R71PS/NaB-K
kW
4.5
5.6
7.1
Btu
15355
19108
24226
kW
5.0
6.3
8.0
Btu
17060
21496
27296
m3/h
700
1000
1100
CFM
412
589
647
Sound Pressure Level (H/L)
dB(A)
40/36
42/38
42/38
External Static Pressure
Pa
50/20
60/30
60/30
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.07
0.15
0.15
A
0.55
1.3
1.3
mm
Φ12.7
Φ15.9
Φ15.9
inch
1/2"
5/8"
5/8"
mm
Φ6.35
Φ9.52
Φ9.52
inch
1/4"
3/8"
3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
980×721×266
1112×756×300
1112×756×300
mm
1068×766×320
1245×785×360
1245×785×360
kg
36/39
51/58
51/58
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
27
DIGITAL MULTI VRF
PRODUCT
Model
Cooling Capacity
Heating Capacity
Air Flow Rate
Sound Pressure Level
(H/L)
External Static Pressure
GMV(L)-R90PS/NaB-K
GMV(L)-R112PS/NaB-K
GMV(L)-R140PS/NaB-K
kW
9.0
11.2
14.0
Btu
30709
38216
47770
kW
10.0
12.5
15.0
Btu
34120
42650
51180
m3/h
1700
1700
2000
CFM
1001
1177
1177
dB(A)
48/44
48/44
50/46
Pa
80/40
80/40
100/50
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.225
0.225
0.26
A
2.15
2.15
2.67
mm
Φ15.9
Φ15.9
Φ15.9
inch
5/8"
5/8"
5/8"
mm
Φ9.52
Φ9.52
Φ9.52
inch
3/8"
3/8"
3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
1425×736×300
1425×736×300
1425×736×300
mm
1514×785×360
1514×785×360
1514×785×360
kg
64/73
64/73
65.5/75
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
28
DIGITAL MULTI VRF
PRODUCT
4.2.2Cassete Type
Model
Cooling Capacity
Heating Capacity
Air Flow Rate
Sound Pressure Level
(H/L)
External Static Pressure
GMV(L)-R28T/Na-K
GMV(L)-R36T/Na-K
GMV(L)-R45T/Na-K
kW
2.8
3.6
4.5
Btu
9550
12280
15360
kW
3.2
4.0
5.0
Btu
10900
13650
17060
m3/h
680
680
680
CFM
400
400
400
dB(A)
37/34
37/34
37/34
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.035
0.035
0.035
A
0.27
0.27
0.28
mm
Φ9.52
Φ12.7
Φ12.7
inch
3/8"
1/2"
1/2"
mm
Φ6.35
Φ6.35
Φ6.35
inch
1/4"
1/4"
1/4"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
Φ30×1.5
Φ30×1.5
mm
Main body:840×840×190
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Net Weight
(Main body/Panel)
Gross Weight
(Main body/Panel)
mm
Panel:950×950×60
Main body:960×960×257
kg
25/6.5
kg
33/10
Panel:1040×1025×115
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
29
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R50T/Na-K
GMV(L)-R56T/Na-K
GMV(L)-R71T/Na-K
kW
5.0
7.1
6.3
Btu
17060
24230
21500
kW
5.8
8.0
7.0
Btu
19790
27300
23890
m3/h
680
1180
1180
CFM
400
695
695
Sound Pressure Level (H/L)
dB(A)
37/34
39/35
39/35
External Static Pressure
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.035
0.035
0.035
A
0.37
0.37
0.37
mm
Φ15.9
Φ15.9
Φ15.9
inch
5/8"
5/8"
5/8"
mm
Φ9.52
Φ9.52
Φ9.52
inch
3/8"
3/8"
3/8"
Flare Connection
Flare Connection
Flare Connection
Φ30×1.5
Φ30×1.5
Φ30×1.5
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Net Weight
(Main body/Panel)
Gross Weight
(Main body/Panel)
mm
Main body:
mm
840×840×190
Panel:950×950×60
Main body:
mm
960×960×257
Panel:1040×1025×115
Main body:840×840×240
Panel:950×950×60
Main body:960×960×310
Panel:1040×1025×115
kg
25/6.5
30/6.5
kg
33/10
38/10
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
30
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R90T/Na-K
GMV(L)-R112T/Na-K
9.0
10.0
11.2
30700
34120
38210
10.0
11.0
12.5
34120
37540
42650
1860
1860
1860
1095
1095
1095
Sound Pressure Level (H/L)
40/36
40/36
40/36
External Static Pressure
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
0.06
kW
0.06
0.06
0.59
A
0.59
0.59
Φ15.9
mm
Φ15.9
Φ15.9
5/8"
inch
5/8"
5/8"
mm
Φ9.52
Φ9.52
inch
3/8"
3/8"
Flare Connection
Flare Connection
Φ30×1.5
Φ30×1.5
Fan Motor
Connecting
Pipes
Φ9.52
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Net Weight
(Main body/Panel)
Gross Weight
(Main body/Panel)
mm
mm
mm
Main body:840×840×320
Panel:950×950×60
Main body:960×960×394
Panel:1040×1025×115
kg
38/6.5
kg
46/10
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
31
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R125T/Na-K
GMV(L)-R140T/Na-K
kW
12.5
14.0
Btu
42650
47770
kW
13.5
14.5
Btu
46062
49470
m3/h
1860
1860
CFM
1095
1095
Sound Pressure Level (H/L)
dB(A)
40/36
40/36
External Static Pressure
Pa
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.06
0.06
Running Current
A
0.59
0.59
mm
Φ15.9
Φ15.9
inch
5/8"
5/8"
mm
Φ9.52
Φ9.52
inch
3/8"
3/8"
Flare Connection
Flare Connection
Φ30×1.5
Φ30×1.5
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Net Weight
(Main body/Panel)
Gross Weight
(Main body/Panel)
mm
mm
mm
Main body:840×840×320
Panel:950×950×60
Main body:960×960×394
Panel:1040×1025×115
kg
38/6.5
kg
46/10
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
32
DIGITAL MULTI VRF
PRODUCT
GMV (L)R22T/NaA-K
GMV(L)R28T/NaA-K
GMV(L)R36T/NaA-K
GMV(L)R45T/NaA-K
kW
2.2
2.8
3.6
4.5
Btu
7506
9554
12283
15354
kW
2.5
3.2
4.0
5.0
Btu
8530
10918
13648
17060
m3/h
600
600
600
600
CFM
353
353
353
353
dB(A)
47/41
47/41
47/41
47/41
220-240V-1Ph50Hz
220-240V-1Ph50Hz
220-240V-1Ph50Hz
220-240V-1Ph50Hz
Model
Cooling Capacity
Heating Capacity
Air Flow Rate
Sound Pressure Level
(H/L)
Power Supply
Fan Motor
Output
kW
0.011
0.011
0.011
0.011
Running
Current
A
0.05
0.05
0.05
0.05
Gas Pipe
Connecting
Pipes
Liquid
Pipe
mm
Φ9.52
Φ12.7
inch
3/8"
1/2"
mm
Φ6.35
Φ6.35
inch
1/4"
1/4"
Flare Connection
Flare Connection
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
mm
Unit Dimensions
(W×D×H)
mm
Main body:570×570×230
Panel:650×650×50
Package Dimensions
(W×D×H)
mm
Main body:848×728×310
Panel:730×670×102
Net Weight
(Main body/Panel)
kg
20/5
Gross Weight
(Main body/Panel)
kg
27/10
Φ30×1.5
Notes:
① Refer to the product nameplate for parameters and specification of the unit;
② The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units dose not have any parameters of performing heating;
③ The sound level was tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher in
actual operation.
33
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R22Td/Na-K
GMV(L)-R28Td/Na-K
GMV(L)-R36Td/Na-K
kW
2.2
2.8
3.6
Btu
7506
9550
12280
kW
2.5
3.2
4.0
Btu
8530
10900
13650
m3/h
450
500
500
CFM
265
294
294
Sound Pressure Level
(H/L)
dB(A)
45/41
45/41
45/41
External Static Pressure
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.02
0.02
0.02
Running
Current
A
0.22
0.22
0.22
mm
Φ9.52
Φ9.52
Φ12.7
inch
3/8"
3/8"
1/2"
mm
Φ6.35
Φ6.35
Φ6.35
inch
1/4"
1/4"
1/4"
Flare Connection
Flare Connection
Flare Connection
Φ30×1.5
Φ30×1.5
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
mm
Φ30×1.5
Unit Dimensions
(W×D×H)
mm
Main body:920×360×185
Package Dimensions
(W×D×H)
mm
Net Weight
(Main body/Panel)
kg
16/3
Gross Weight
(Main body/Panel)
kg
25/5
Panel:1180×430×30
Main body:1290×465×270
Panel:1260×505×110
Notes:
① Refer to the product nameplate for parameters and specification of the unit;
② The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling only
units dose not have any parameters of performing heating;
③ The sound level was tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher in
actual operatio
34
DIGITAL MULTI VRF
PRODUCT
4.2.3Wall mounted Type
Model
GMV(L)-R22G/NaB-K
GMV(L)-R28G/NaB-K
GMV(L)-R36G/NaB-K
kW
2.2
2.8
3.6
Btu
7507
9554
12284
kW
2.5
3.2
4.0
Btu
8530
10919
13649
m3/h
360
360
500
CFM
212
212
294
Sound Pressure Level (H/L)
dB(A)
37/28
37/28
43/28
External Static Pressure
Pa
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.014
0.014
0.022
A
0.15
0.15
0.22
mm
Φ9.52
Φ9.52
Φ12.7
inch
Φ3/8
Φ3/8
Φ1/2
mm
Φ6.35
Φ6.35
Φ6.35
inch
Φ1/4
Φ1/4
Φ1/4
Flare Connection
Flare Connection
Flare Connection
mm
Φ20×1.5
Φ20×1.5
Φ20×1.5
mm
830×189×285
830×189×285
830×189×285
mm
995×394×268
995×394×268
995×394×268
kg
8/14.3
8/14.3
11/15.8
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
35
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R45G/NaB-K
GMV(L)-R50G/NaB-K
GMV(L)-R56G/NaB-K
kW
4.5
5.0
5.6
Btu
15355
17061
19108
kW
5.0
5.8
6.3
Btu
17061
19790
21496
m3/h
500
700
750
CFM
294
412
441
Sound Pressure Level (H/L)
dB(A)
43/28
45/40
45/40
External Static Pressure
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.022
0.02
0.02
A
0.22
0.25
0.26
mm
Φ12.7
Φ12.7
Φ15.9
inch
Φ1/2
Φ1/2
Φ5/8
mm
Φ6.35
Φ6.35
Φ9.52
inch
Φ1/4
Φ1/4
Φ3/8
Flare Connection
Flare Connection
Flare Connection
mm
Φ20×1.5
Φ30×1.5
Φ30×1.5
mm
830×189×285
1020×228×310
1020×228×310
mm
1006×385×265
1178×325×390
1178×325×390
kg
11/15.8
15.5/20.5
15.5/20.5
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
36
DIGITAL MULTI VRF
PRODUCT
Model
Cooling Capacity
Heating Capacity
Air Flow Rate
Sound Pressure Level (H/L)
External Static Pressure
GMV(L)-R22G/NaC-K
GMV(L)-R28G/NaC-K
GMV(L)-R36G/NaC-K
kW
2.2
2.8
3.6
Btu
7507
9554
12284
kW
2.5
3.2
4.0
Btu
8530
10919
13649
m3/h
360
360
500
CFM
212
212
294
37/28
37/28
43/28
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.014
0.014
0.022
A
0.15
0.15
0.22
mm
Φ9.52
Φ9.52
Φ12.7
inch
Φ3/8
Φ3/8
Φ1/2
mm
Φ6.35
Φ6.35
Φ6.35
inch
Φ1/4
Φ1/4
Φ1/4
Flare Connection
Flare Connection
Flare Connection
mm
Φ20×1.5
Φ20×1.5
Φ20×1.5
mm
770×190×250
770×190×250
830×189×285
mm
955×330×272
955×272×330
1006×395×295
kg
8/14.3
8/14.3
11/15.8
dB(A
)
Pa
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
37
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R45G/NaC-K
GMV(L)-R71G/Na-K
GMV(L)-R80G/Na-K
kW
4.5
7.1
8.0
Btu
15355
24226
27297
kW
5.0
8.0
9.0
Btu
17061
27297
30709
m3/h
500
1200
1200
CFM
294
706
706
dB(A)
43/28
49/42
49/42
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.022
0.026
0.026
A
0.22
0.29
0.39
mm
Φ12.7
Φ15.9
Φ15.9
inch
1/2"
5/8"
5/8"
Liquid
mm
Φ6.35
Φ9.52
Φ9.52
Pipe
inch
1/4"
3/8"
3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ30×1.5
φ30×1.5
φ30×1.5
mm
830×189×285
1178×227×326
1178×227×326
mm
1006×395×295
1365×417×333
1365×417×333
kg
11/15.8
17.5/23
17.5/23
Cooling Capacity
Heating Capacity
Air Flow Rate
Sound Pressure Level
(H/L)
External Static
Pressure
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connectin
g Pipes
Connection Method
Drain Pipes
(External Dia. ×
Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
38
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R22G/NaG-K
GMV(L)-R28G/NaG-K
GMV(L)-R36G/NaG-K
kW
2.2
2.8
3.6
Btu
7507
9554
12284
kW
2.5
3.2
4.0
Btu
8530
10919
13649
m3/h
500
500
630
CFM
294
294
371
Sound Pressure Level (H/L)
dB(A)
38/34
38/34
44/38
External Static Pressure
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.02
0.02
0.02
Running Current
A
0.31
0.31
0.36
mm
Φ9.52
Φ9.52
Φ12.7
inch
3/8"
3/8"
1/2"
mm
Φ6.35
Φ6.35
Φ6.35
inch
1/4"
1/4"
1/4"
Flare Connection
Flare Connection
Flare Connection
mm
Φ28×4
Φ28×4
Φ28×4
mm
843×180×275
843×180×275
940×200×298
mm
915×255×355
915×255×355
1010×380×285
kg
10.5/12.5
10.5/12.5
13/16
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
39
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R45G/NaG-K
GMV(L)-R50G/NaG-K
GMV(L)-R56G/NaG-K
kW
4.5
5.0
5.6
Btu
15355
17061
19108
kW
5.0
5.8
6.3
Btu
17061
19790
21496
m3/h
630
630
800
CFM
371
371
471
Sound Pressure Level (H/L)
dB(A)
44/38
44/38
44/38
External Static Pressure
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.02
0.02
0.03
Running Current
A
0.36
0.36
0.4
mm
Φ12.7
Φ12.7
Φ15.87
inch
1/2"
1/2"
5/8"
mm
Φ6.35
Φ6.35
Φ9.52
inch
1/4"
1/4"
3/8"
Flare Connection
Flare Connection
Flare Connection
mm
Φ28×4
Φ28×4
Φ28×4
mm
940×200×298
940×200×298
1008×221×319
mm
1010×380×285
1010×380×285
1073×395×313
kg
13/16
13/16
15/20
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
40
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R63G/NaG-K
GMV(L)-R71G/NaG-K
kW
6.3
7.1
Btu
21496
24226
kW
7.0
8.0
Btu
23885
27297
m3/h
800
800
CFM
471
471
Sound Pressure Level (H/L)
dB(A)
44/38
44/38
External Static Pressure
Pa
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.03
0.03
Running Current
A
0.4
0.4
mm
Φ15.87
Φ15.87
inch
5/8"
5/8"
mm
Φ9.52
Φ9.52
inch
3/8"
3/8"
Flare Connection
Flare Connection
mm
Φ28×4
Φ28×4
mm
1008×221×319
1008×221×319
mm
1073×395×313
1073×395×313
kg
15/20
15/20
Gas Pipe
Connecting Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
41
DIGITAL MULTI VRF
PRODUCT
4.2.4Floor Ceiling Type
Model
GMV(L)-R28Zd/Na-K
GMV(L)-R36Zd/Na-K
GMV(L)-R50Zd/Na-K
kW
2.8
3.6
5.0
Btu
9554
12284
17061
kW
3.2
4.0
5.8
Btu
10919
13649
19790
m3/h
550
600
700
CFM
324
353
412
Sound Pressure Level (H/L)
dB(A)
43/-
44/-
50/-
External Static Pressure
Pa
0
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
kW
0.01
0.01
0.04
A
0.1
0.1
0.4
mm
Φ9.52
Φ12.7
Φ12.7
inch
Φ3/8
Φ1/2
Φ1/2
mm
Φ6.35
Φ6.35
Φ6.35
inch
Φ1/4
Φ1/4
Φ1/4
Flare Connection
Flare Connection
Flare Connection
mm
Φ17×1.75
Φ17×1.75
Φ17×1.75
mm
840×238×695
840×238×695
840×238×695
mm
1035×295×805
1035×295×805
1035×295×805
kg
28/37
28/37
28/37
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
Fan Motor
Running
Current
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
42
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R71Zd/Na-K
GMV(L)-R90Zd/Na-K
kW
7.1
9.0
Btu
24226
30709
kW
8.0
10.0
Btu
27297
34121
m3/h
1170
2100
CFM
689
1236
Sound Pressure Level (H/L)
dB(A)
48/-
51/-
External Static Pressure
Pa
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Output
kW
0.1
0.15
Running Current
A
1
1.5
mm
Φ15.9
Φ15.9
inch
Φ5/8
5/8
mm
Φ9.52
Φ9.52
inch
Φ3/8
3/8
Flare Connection
Flare Connection
mm
Φ17×1.75
Φ17×1.75
Unit Dimensions(W×D×H)
mm
1300×188×600
1590×238×695
Package Dimensions(W×D×H)
mm
1514×248×724
1714×330×830
Weight(Net/Gross)
kg
34/38
44/53
Fan Motor
Gas Pipe
Connecting Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
43
DIGITAL MULTI VRF
PRODUCT
Model
GMV(L)-R112Zd/Na-K
GMV(L)-R125Zd/Na-K
kW
11.2
12.5
Btu
38216
42652
kW
12.5
13.5
Btu
42652
46064
m3/h
2200
2300
CFM
1295
1354
Sound Pressure Level (H/L)
dB(A)
54/-
55/-
External Static Pressure
Pa
0
0
220-240V-1Ph-50Hz
220-240V-1Ph-50Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.18
0.18
Running Current
A
1.8
1.8
mm
Φ15.9
Φ15.9
inch
5/8
5/8
mm
Φ9.52
Φ9.52
inch
3/8
3/8
Flare Connection
Flare Connection
mm
Φ17×1.75
Φ17×1.75
mm
1590×238×695
1590×238×695
mm
1714×330×830
1714×330×830
kg
44/53
44/53
Gas Pipe
Connecting Pipes
Liquid Pipe
Connection Method
Drain Pipes
(External Dia. × Thickness)
Unit Dimensions
(W×D×H)
Package Dimensions
(W×D×H)
Weight(Net/Gross)
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
44
DIGITAL MULTI VRF
PRODUCT
Model
GMV-R71Zd/NaB-K
GMV-R90Zd/NaB-K
kW
7.1
9.0
Btu
24226
30709
kW
8.0
10.0
Btu
27297
34121
m3/h
1400
1600
CFM
824
942
Sound Pressure Level (H/L)
dB(A)
49
51
External Static Pressure
Pa
0
0
208-230V 1Ph~ 60Hz
208-230V 1Ph~ 60Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.075
0.15
Running Current
A
0.64
0.82
mm
Φ15.9
Φ15.9
inch
5/8
5/8
mm
Φ9.52
Φ9.52
inch
3/8
3/8
Flare Connection
Flare Connection
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes (External Dia. × Thickness)
mm
Φ17×1.75
Φ17×1.75
Unit Dimensions (W×D×H)
mm
1420×700×245
1420×700×245
Package Dimensions (W×D×H)
mm
1530×825×330
1530×825×330
Weight (Net/Gross)
kg
52/61
54/63
Notes:
①
Refer to the product nameplate for parameters and specification of the unit;
②
The model with GMVL code is cooling only unit; while the model with GMV code is heat pump unit; the cooling
only units does not have any parameters of performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
45
DIGITAL MULTI VRF
PRODUCT
Model
GMV-R112Zd/NaB-K
GMV-R140Zd/NaB-K
kW
11.2
14.0
Btu
38216
47770
kW
12.5
16.0
Btu
42652
49470
m3/h
2000
2000
CFM
1177
1177
Sound Pressure Level (H/L)
dB(A)
55
55
External Static Pressure
Pa
0
0
208-230V 1Ph~ 60Hz
208-230V 1Ph~ 60Hz
Cooling Capacity
Heating Capacity
Air Flow Rate
Power Supply
Fan Motor
Output
kW
0.18
0.18
Running Current
A
1.1
1.1
mm
Φ15.9
Φ15.9
inch
5/8
5/8
mm
Φ9.52
Φ9.52
inch
3/8
3/8
Flare Connection
Flare Connection
Gas Pipe
Connecting
Pipes
Liquid Pipe
Connection Method
Drain Pipes(External Dia. × Thickness)
mm
Φ17×1.75
Φ17×1.75
Unit Dimensions (W×D×H)
mm
1700×700×245
1700×700×245
Package Dimensions (W×D×H)
mm
1810×825×330
1810×825×330
Weight(Net/Gross)
kg
64/72
66/74
Notes:
①
②
Refer to the product nameplate for parameters and specification of the unit;
while the model with GMV code is heat pump unit; the cooling only units does not have any parameters of
performing heating;
③
The sound level is tested under circumstance of semi-anechoic chamber; the value of noise could be a little higher
in actual operation.
4.3 Operation Range
Model
Range of outdoor temperature①(①)
Cooling
16①(61①)~30①(85①)
Heating
16①(61①)~30①(85①)
46
DIGITAL MULTI VRF
PRODUCT
5 PIPING DIAGRAM
GMV-R120W/Na-K, GMV-R160W/Na-M
1
Digital compressor
16
High pressure swich
2
Compressor discharge pipe thermistor
17
Gas by-pass value sub-assy: Capillary
3
Compressor oil thermistor
18
Gas by-pass value sub-assy: Electromagnetic value
4
PWM value
19
Condenser
5
Oil separator
20
Condenser inlet pipe thermistor
6
Oil separator sub-assy: Capillary
21
Condenser middle pipe thermistor
7
4-Way valve
22
Condenser outlet pipe thermistor
8
4-Way valve sub-assy: Filter
23
Ambient thermistor
9
Liquid valve sub-assy: Drier
24
Outdoor fan
10
Liquid valve
25
EXV sub-assy:Filter
11
Gas valve sub-assy:Filter
26
EXV sub-assy: One way valve
12
Gas valve
27
EXV sub-assy: Electronic expansion value
13
Gas-liquid separator
28
Liquid by-pass value sub-assy: Capillary
14
Low pressure sensor
29
Liquid by-pass value sub-assy: Electromagnetic value
15
High pressure sensor
47
DIGITAL MULTI VRF
PRODUCT
GMVL-R120W/Na-K, GMVL-R160W/Na-M
1
Digital compressor
16
Gas by-pass value sub-assy: Electromagnetic value
2
Compressor discharge pipe thermistor
17
Condenser
3
Compressor oil thermistor
18
Condenser inlet pipe thermistor
4
PWM value
19
Condenser middle pipe thermistor
5
Oil separator
20
Condenser outlet pipe thermistor
6
Oil separator sub-assy: Capillary
21
Ambient thermistor
7
Liquid valve sub-assy: Drier
22
Outdoor fan
8
Liquid valve
23
EXV sub-assy:Filter
9
Gas valve sub-assy:Filter
24
EXV sub-assy: One way valve
10
Gas valve
25
EXV sub-assy: Electronic expansion value
11
Gas-liquid separator
26
Liquid by-pass value sub-assy: Capillary
12
Low pressure sensor
27
Liquid by-pass value sub-assy: Electromagnetic value
13
High pressure sensor
28
Liquid accumulator
14
High pressure swich
15
Gas by-pass value sub-assy: Capillary
48
DIGITAL MULTI VRF
PRODUCT
GMV-R260W2/Na- M, GMV-R300W2/Na-M
1
Constant-speed compressor
18
High pressure sensor
2
Digital compressor
19
High pressure swich
3
Compressor discharge pipe thermistor
20
Gas by-pass value sub-assy: Electromagnetic value
4
Compressor oil thermistor
21
Gas by-pass value sub-assy: Capillary
5
PWM value
22
Condenser
6
Oil separator
23
Condenser inlet pipe thermistor
7
Oil separator sub-assy: Filter
24
Condenser middle pipe thermistor
8
Oil separator sub-assy: Capillary
25
Condenser outlet pipe thermistor
9
Oil separator sub-assy: One way valve
26
Ambient thermistor
10
4-Way valve
27
Outdoor fan
11
4-Way valve sub-assy: Filter
28
EXV sub-assy:Filter
12
Liquid valve sub-assy: Drier
29
EXV sub-assy: One way valve
13
Liquid valve
30
Electronic expansion valve
14
Gas valve sub-assy:Filter
31
Liquid by-pass value sub-assy: Electromagnetic value
15
Gas valve
32
Liquid by-pass value sub-assy: Capillary
16
Gas-liquid separator
33
Oil equalization pipe
17
Low pressure sensor
34
Gas equalization pipe
49
DIGITAL MULTI VRF
PRODUCT
GMVL-R260W2/Na- M, GMVL-R300W2/Na-M
1
Constant-speed compressor
18
Gas by-pass value sub-assy: Electromagnetic value
2
Digital compressor
19
Gas by-pass value sub-assy: Capillary
3
Compressor discharge pipe thermistor
20
Condenser
4
Compressor oil thermistor
21
Condenser inlet pipe thermistor
5
PWM value
22
Condenser middle pipe thermistor
6
Oil separator
23
Condenser outlet pipe thermistor
7
Oil separator sub-assy: Filter
24
Ambient thermistor
8
Oil separator sub-assy: Capillary
25
Outdoor fan
9
Oil separator sub-assy: One way valve
26
EXV sub-assy:Filter
10
Liquid valve sub-assy: Drier
27
EXV sub-assy: One way valve
11
Liquid valve
28
Electronic expansion valve
12
Gas valve sub-assy:Filter
29
Liquid by-pass value sub-assy: Electromagnetic value
13
Gas valve
30
Liquid by-pass value sub-assy: Capillary
14
Gas-liquid separator
31
Oil equalization pipe
15
Low pressure sensor
32
Gas equalization pipe
16
High pressure sensor
33
Liquid accumulator
17
High pressure swich
34
50
DIGITAL MULTI VRF
PRODUCT
GMV-R450W3/Na-M
1
Constant-speed compressor
20
Gas by-pass value sub-assy: Electromagnetic value
2
Digital compressor
21
Gas by-pass value sub-assy: Capillary
3
Compressor discharge pipe thermistor
22
Condenser
4
Compressor oil thermistor
23
Condenser inlet pipe thermistor
5
PWM value
24
Condenser middle pipe thermistor
6
Oil separator
25
Condenser outlet pipe thermistor
7
Oil separator sub-assy: Filter
26
Ambient thermistor
8
Oil separator sub-assy: Capillary
27
Outdoor fan
9
Oil separator sub-assy: One way valve
28
EXV sub-assy: Capillary
10
4-Way valve
29
EXV sub-assy: Electromagnetic value
11
4-Way valve sub-assy: Filter
30
Electronic expansion valve
12
Liquid valve sub-assy: Drier
31
EXV sub-assy: One way valve
13
Liquid valve
32
EXV sub-assy: Filter
14
Gas valve sub-assy:Filter
33
Liquid accumulator
15
Gas valve
34
Liquid by-pass value sub-assy: Capillary
16
Gas-liquid separator
35
Liquid by-pass value sub-assy: Electromagnetic value
17
Low pressure sensor
36
Oil equalization pipe
18
High pressure sensor
37
Gas equalization pipe
19
High pressure swich
51
DIGITAL MULTI VRF
PRODUCT
GMVL-R450W3/Na-M
1
Constant-speed compressor
19
Gas by-pass value sub-assy: Capillary
2
Digital compressor
20
Condenser
3
Compressor discharge pipe thermistor
21
Condenser inlet pipe thermistor
4
Compressor oil thermistor
22
Condenser middle pipe thermistor
5
PWM value
23
Condenser outlet pipe thermistor
6
Oil separator
24
Ambient thermistor
7
Oil separator sub-assy: Filter
25
Outdoor fan
8
Oil separator sub-assy: Capillary
26
EXV sub-assy: Capillary
9
Oil separator sub-assy: One way valve
27
EXV sub-assy: Electromagnetic value
10
Liquid valve sub-assy: Filter
28
Electronic expansion valve
11
Liquid valve
29
EXV sub-assy: One way valve
12
Gas valve sub-assy: Filter
30
EXV sub-assy: Filter
13
Gas valve
31
Liquid accumulator
14
Gas-liquid separator
32
Liquid by-pass value sub-assy: Capillary
15
Low pressure sensor
33
Liquid by-pass value sub-assy: Electromagnetic value
16
High pressure sensor
34
Oil equalization pipe
17
High pressure swich
35
Gas equalization pipe
18
Gas by-pass value sub-assy: Electromagnetic value
52
DIGITAL MULTI VRF
PRODUCT
GMV-R560W4/Na-M, GMV-R600W4/Na-M
1
Constant-speed compressor
19
High pressure swich
2
Digital compressor
20
Gas by-pass value sub-assy: Electromagnetic value
3
Compressor discharge pipe thermistor
21
Gas by-pass value sub-assy: Capillary
4
Compressor oil thermistor
22
Condenser
5
PWM value
23
Condenser inlet pipe thermistor
6
Oil separator
24
Condenser middle pipe thermistor
7
Oil separator sub-assy: Filter
25
Condenser outlet pipe thermistor
8
Oil separator sub-assy: Capillary
26
Ambient thermistor
9
Oil separator sub-assy: One way valve
27
Outdoor fan
10
4-Way valve
28
EXV sub-assy: One way valve
11
4-Way valve sub-assy: Filter
29
EXV sub-assy: Filter
12
Liquid valve sub-assy: Filter
30
EXV sub-assy: Drier
13
Liquid valve
31
Electronic expansion valve
14
Gas valve sub-assy: Filter
32
Liquid accumulator
15
Gas valve
33
Liquid by-pass value sub-assy: Capillary
16
Gas-liquid separator
34
Liquid by-pass value sub-assy: Electromagnetic value
17
Low pressure sensor
35
Oil equalization pipe
18
High pressure sensor
36
Gas equalization pipe
53
DIGITAL MULTI VRF
PRODUCT
GMVL-R560W4/Na-M, GMVL-R600W4/Na-M
1
Constant-speed compressor
18
Gas by-pass value sub-assy: Electromagnetic value
2
Digital compressor
19
Gas by-pass value sub-assy: Capillary
3
Compressor discharge pipe thermistor
20
Condenser
4
Compressor oil thermistor
21
Condenser inlet pipe thermistor
5
PWM value
22
Condenser middle pipe thermistor
6
Oil separator
23
Condenser outlet pipe thermistor
7
Oil separator sub-assy: Filter
24
Ambient thermistor
8
Oil separator sub-assy: Capillary
25
Outdoor fan
9
Oil separator sub-assy: One way valve
26
EXV sub-assy: One way valve
10
Liquid valve sub-assy: Filter
27
EXV sub-assy: Filter
11
Liquid valve
28
EXV sub-assy: Drier
12
Gas valve sub-assy: Filter
29
Electronic expansion valve
13
Gas valve
30
Liquid accumulator
14
Gas-liquid separator
31
Liquid by-pass value sub-assy: Capillary
15
Low pressure sensor
32
Liquid by-pass value sub-assy: Electromagnetic value
16
High pressure sensor
33
Oil equalization pipe
17
High pressure swich
34
Gas equalization pipe
54
DIGITAL MULTI VRF
PRODUCT
GMV-R860W6/Na-M, GMV-R900W6/Na-M
1
Constant-speed compressor
20
Gas by-pass value sub-assy: Electromagnetic value
2
Digital compressor
21
Gas by-pass value sub-assy: Capillary
3
Compressor discharge pipe thermistor
22
Condenser
4
Compressor oil thermistor
23
Condenser inlet pipe thermistor
5
PWM value
24
Condenser middle pipe thermistor
6
Oil separator
25
Condenser outlet pipe thermistor
7
Oil separator sub-assy: Filter
26
Ambient thermistor
8
Oil separator sub-assy: Capillary
27
Outdoor fan
9
Oil separator sub-assy: One way valve
28
EXV sub-assy: Capillary
10
4-Way valve
29
EXV sub-assy: Electromagnetic value
11
4-Way valve sub-assy: Filter
30
Electronic expansion valve
12
Liquid valve sub-assy: Drier
31
EXV sub-assy: One way valve
13
Liquid valve
32
EXV sub-assy: Filter
14
Gas valve sub-assy: Filter
33
Liquid accumulator
15
Gas valve
34
Liquid by-pass value sub-assy: Capillary
16
Gas-liquid separator
35
Liquid by-pass value sub-assy: Electromagnetic value
17
Low pressure sensor
36
Oil equalization pipe
18
High pressure sensor
37
Gas equalization pipe
19
High pressure swich
55
DIGITAL MULTI VRF
PRODUCT
GMVL-R860W6/Na-M, GMVL-R900W6/Na-M
1
Constant-speed compressor
19
Gas by-pass value sub-assy: Capillary
2
Digital compressor
20
Condenser
3
Compressor discharge pipe thermistor
21
Condenser inlet pipe thermistor
4
Compressor oil thermistor
22
Condenser middle pipe thermistor
5
PWM value
23
Condenser outlet pipe thermistor
6
Oil separator
24
Ambient thermistor
7
Oil separator sub-assy: Filter
25
Outdoor fan
8
Oil separator sub-assy: Capillary
26
EXV sub-assy: Capillary
9
Oil separator sub-assy: One way valve
27
EXV sub-assy: Electromagnetic value
10
Liquid valve sub-assy: Drier
28
Electronic expansion valve
11
Liquid valve
29
EXV sub-assy: One way valve
12
Gas valve sub-assy: Filter
30
EXV sub-assy: Filter
13
Gas valve
31
Liquid accumulator
14
Gas-liquid separator
32
Liquid by-pass value sub-assy: Capillary
15
Low pressure sensor
33
Liquid by-pass value sub-assy: Electromagnetic value
16
High pressure sensor
34
Oil equalization pipe
17
High pressure swich
35
Gas equalization pipe
18
Gas by-pass value sub-assy: Electromagnetic value
56
GREE COMMERCIAL AIR CONDITION
DIGITAL MULTI VRF
CONTROL
57
DIGITAL MULTI VRF
CONTROL
CONTROL
1 OPERATION FLOWCHART
58
DIGITAL MULTI VRF
CONTROL
1.1 Cooling/Dehumidfying Operation
Cooling Operation
Guide Louver
There Is Not
There Is
Guide Louvers Swing
Fan Motor: Operation
In The Process Of
Preventing Restart Operation?
(3 Minutes)
Yes
No
Temperature
Adjustment?
Yes
No
Fan Motor:Stop
Electronic Expansion Valve: Close
Electronic Expansion
Valve: Capacity Control
A
(Go To The Previous Page)
59
DIGITAL MULTI VRF
CONTROL
1.2 Heating Operation
60
DIGITAL MULTI VRF
CONTROL
2 MAIN LOGIC
2.1 Control Function of Outdoor Unit
1)
Compressor Capacity Output
It is defined that the full load capacity output of the compressor is 100%.
The compressor capacity output is calculated according to the required indoor load, which is related to
the following factors: whether the indoor unit is started, the set temperature, the indoor ambient
temperature, the outdoor ambient temperature, etc.
Capacity output calculation of compressor during cooling:
j
Q=
∑ (q
iON
Ai )
i =1
j
∑q
i =1
× 100%
i
Capacity output calculation of compressor during heating:
j
Q=
∑ (q
i =1
iON
Ai + qiOFF × Bi )
j
∑q
i =1
× 100%
i
Among which:
Q is the calculated compressor capacity output;
qi is the rated capacity of the indoor unit;
qiON is the rated capacity of indoor unit during running;
qiOFF is the rated capacity of the indoor unit when it is not switched on;
Ai is the set temperature, indoor and outdoor ambient temperature correction, %
Bi is the indoor unit capacity compensation when the heating operation is not running, %
2)
Compressor Start Control
◆The shortest operating time of the compressor is 6 minutes. But when the switching-off signal or
the protection signal is received, the compressor must stop even if the operation of it has not lasted for 6
minutes.
◆The shortest stoppage period of the compressor is 3 minutes. The compressor must not be started at
any time within 3 minutes after the compressor is stopped.
◆If the capacity demand of each indoor unit is 0 when the whole unit group is under heating state,
the compressor must be stopped (if under the heating operation alone the temperature of stop control is
reached , the compressor must be stopped).
★Initial Sequence Chart of Cooling/Dehumidifying Modes:
61
DIGITAL MULTI VRF
CONTROL
★ Initial Sequence Chart of Heating Mode:
3)
Outdoor Fan Motor Control
There is one 8KW outdoor fan motor which is a double-speed fan motor under 3-grade control: high
speed grade, low speed grade and stop; There are two 10KW~15KW outdoor fan motor which are
double-speed fan motors under 3-grade control: high speed grade, low speed grade and stop.
The 20KW~30 KW outdoor fan motor is of stepless speed regulation, and stops at 13 grads: 1,2…9,
A,B,C.
62
DIGITAL MULTI VRF
CONTROL
The detailed control modes are as follows:
(1) Cooling Mode:
When the unit is turned on, the fan motor operates at high speed grade for 250 seconds;
The exhaust pressure is detected 250 seconds after the unit is switched on. The speed grade of the fan
motor is adjusted once every three cycles according to the mean value of the exhaust pressure. Refer to the
following table for the control:
Absolute pressure of
exhaust (Mpa)
Cooling
≤1.3
1.3<P<1.6
≥1.6
Go to the lower grade
Remain unchanged
Go to the higher grade
If the fan motor is at the low speed grade, the grade cannot go lower; if the fan motor is at the high
speed grade, the grade cannot go higher.
(2) Heating Mode:
When the unit is turned on, the fan motor operates at high speed grade for 250 seconds;
The air suction pressure is detected 250 seconds after the unit is switched on. The speed grade of the
fan motor is adjusted once every three cycles according to the mean value of the air suction pressure. Refer
to the following table for the control:
Temperature
corresponding to the air
≤1
1<P<6
≥6
Go to the higher grade
Remain Unchanged
Go to the lower grade
suction pressure
cooling
If the fan motor is at the stop grade, the grade cannot go lower; if the fan motor is at the high speed
grade, the grade cannot go higher.
4)
Compressor Protection Function
a) High Pressure Control
If any one of the two conditions is realized, the high pressure protection function is activated:
Condition 1: The high pressure reaches 3.0Mpa, which is the protection-starting value, then the
high pressure switch disconnects;
Condition 2: The high pressure temperature of the high pressure sensor equals or is higher than
67.
Time of Detection: 3S
Action after high pressure protection:
The outdoor unit controller stops the compressor and send “Fault” signal to the indoor units to
release all load. Now the compressor high pressure protection code E1 is displayed and automatic
recovery is not allowed again. Even after the stop protection keeps on for 3 minutes, the unit cannot
be restart. Now the user must call serviceman to inspect the air-conditioner. The only way to clear
high pressure protection is to de-energize the unit and then restart the unit.
During cooling:
63
DIGITAL MULTI VRF
CONTROL
During heating:
TAmbient >=TSetting + 1ºC
Target
2 Minutes
3 Seconds
4-Way
High
Display E1
Display
ON/OFF
Indoor Unit
Outdoor Fan
1 Seconds
Compressor
B.System Low Pressure Protection
The low pressure detection is not available within 4 minutes after the compressor starts, and
during the operation of system oil return and defrosting. Under other circumstances:
Condition 1: When it is detected that the low pressure temperature is lower than -25① under any
circumstance during cooling, or when it is detected that the low pressure temperature is lower than
-32① under any circumstance during heating, the protection will start at once, and the low pressure
protection will be displayed.
Detection Time: 30S
The low pressure recovery pressure is 0①, and the unit shall restart after 3 minutes.
If there are three times of low pressure protection within 1 hour, the outdoor unit must be
de-energized and then be energized again to restart.
64
DIGITAL MULTI VRF
Target
CONTROL
TAmbient >=TSetting + 1ºC
30 Seconds
30 Seconds
Another
Low
Display E3 For
Three Times
Display
ON/OFF
Another
Indoor Unit
Another
Outdoor Fan
1 Seconds
1 Seconds
Another
Compressor
Stop Operation For 3 Minutes
C. Overcurrent Protection
If it is detected that the current is over the protection-starting value for 3 consecutive seconds
when the compressor operates, the compressor will be stopped as the stop condition the same as that
when the indoor ambient temperature reaches the set temperature. The compressor shall resume
original operating status after stopping for 3 minutes; but if the occurrence of protection is over 6
times (if the operating time of the compressor exceeds 6 minutes, the times of protection will be
cleared to zero), the timing indicating light will flicker and the compressor cannot resume to the
original operating status.
D.High Temperature Protection of Compressor Exhaust Pipe
120
130
110
Discharge temp
ON
liquit bypass valve
OFF
Auto
add 10B
Indoor EXV
Auto
Auto
Compressor
drop 10%
stop point
Note :
◆This function of cooling is the same as that of heating. Pay attention that the 4-way valve has a
time lag of 2 minutes.
◆Press the ON/OFF key to switch off the unit and to remove the voice alarm. If there is still
compressor exhaust protection after the compressor is started, only one detection will be carried out
and E4 will be displayed. Now the buzzer sends out alarm (if there is only a receiver, there will be no
buzzer alarm function).
65
DIGITAL MULTI VRF
CONTROL
E. Communication Failure
Target
TAmbient >=TSetting + 1ºC
30 Seconds
Communication is Normal
Communic
Normal
Display
Display E6
Display
ON/OFF
Indoor Unit
Outdoor Fan
1 Seconds
1 Seconds
Compressor
Stop Operation For 3 Minutes
5)
Defrosting Function
The heating operation continues for 50 minutes (now the 4-way valve is in the heating position); the
Mid. Temp.sensor temperature and the outdoor ambient temperature remain below the curve shown in the
following chart for 120S.
0
Mid. Temp.Sensor
Temperature
-5
-10
-15
-10
-5
0
5
10
Outdoor Dry-Bulb Temperature
Or:
The outdoor ambient temperature is lower than -6①; the heating operation keeps on for 2 hours
(now the 4-way valve is in the heating position);
z Condition of stopping defrosting:
The worm pipe temperature of the outdoor unit is higher than 15① or the defrosting operation
keeps on for 10 minutes.
z Defrosting Action
Defrosting is realized by switching the 4-way valve to the cooling mode.
The defrosting process sequence chart of the unit group is shown as follows:
66
DIGITAL MULTI VRF
CONTROL
ON
ON
X%(
)
ON
ON
67
DIGITAL MULTI VRF
CONTROL
2.2 Control Function of Indoor Unit
1) Cooling Operation
a) Cooling
According to the capacity demand of the running indoor unit, the outdoor unit decides the
frequency under which the compressor runs.
control of the outdoor unit, the indoor unit decides the openness of the electronic expansion
valve. The electronic expansion valve is set once every 40 seconds.
b) Temperature Control
Through the openness and close of the indoor electronic expansion valve, the indoor unit realizes
the control to the temperature (refer to the following figure).
When the capacity demand of the indoor unit is 0, the electronic expansion valve closes.
When the capacity demand of the indoor unit is not 0, the electronic expansion valve opens.
If the indoor units of the same unit group all reach the temperature point, the demand of the unit
group is 0, now the outdoor unit shall stop the operation of the compressor and the electronic
expansion valve of the indoor unit closes.
c) Indoor Fan Motor Action
When the indoor unit operates and the fan motor is not set at the automatic air speed grade, the
indoor fan motor continue operating at the set air speed whether the capacity demand is 0.
When the indoor fan motor is set at the automatic air speed grade, the fan motor decides the fan
motor air speed according to the change of ambient temperature indoors. Refer to the following
figure:
The switch under the automatic air speed grade is inspected once every 30 seconds.
68
DIGITAL MULTI VRF
CONTROL
If the indoor fan motor stops before, the fan motor will start compulsory operation under high air
speed grade for 8 seconds and then operates under set air speed.
d)
Control of Blowing off Residual Cold Air
When the indoor unit stops, the fan motor operates under set air speed or automatic air speed
condition for 0-60 seconds.
When the capacity demand of the indoor unit is 0, the electronic expansion valve of the indoor
unit closes and the fan motor continue operating under set air speed or automatic air speed condition.
2)
Dehumidifying Operation
When the unit operates under the dehumidifying mode, the indoor unit can only operates under the
low air speed grade (regardless of the set air speed grade). Other actions are the same as that of the cooling
operation. Please refer to the section of cooling operation.
The indoor fan motor stops before, the fan motor will be started to carry out compulsory
operation under high air speed grade for 8 seconds and then operates under set air speed.
3)
Heating Operation
a) Heating
According to the capacity demand of the running indoor unit, the outdoor unit decides the
frequency under which the compressor runs.
Control of the outdoor unit. The indoor unit decides the openness of the electronic expansion
valve. The electronic expansion valve is set once every 40 seconds.
b) Temperature Control
Through the openness and close of the indoor electronic expansion valve, the indoor unit realizes
the control of the temperature (refer to the following figure).
When the capacity demand of the indoor unit is 0, the electronic expansion valve closes.
When the capacity demand of the indoor unit is not 0, the electronic expansion valve opens.
c) Fan Motor Control
When the indoor unit has capacity demand:
If automatic air speed grade is not set, the fan motor of the indoor unit will operate under set air
speed grade;
When the indoor fan motor is set at the automatic air speed grade, the fan motor decides the fan
motor air speed according to the change of ambient temperature indoors. Refer to the following
figure:
69
DIGITAL MULTI VRF
CONTROL
High Air Speed Grade
Medium Air Speed Grade
Low Air Speed Grade
-3
-2
-1
+1
Indoor Ambient Temperature
+2
Indoor Set Temperature
Automatic Air Speed Grade For Heating (Linge Wind)
The switch under the automatic air speed grade is inspected once every 30 seconds.
The indoor fan motor stops before, the fan motor will start compulsory operation under high air
speed grade for 8 seconds and then operates under set air speed.
d) Operation of Preventing Cold Air
When the indoor unit has capacity demand, the indoor fan motor will be compulsorily turned to
close status and operate under the following conditions:
If the evaporator temperature (tevaporator) of the indoor unit reaches the threshold Tv evaporator, the
indoor fan motor will carry out compulsory operation under high air speed grade for 8 seconds and
then operates under set air speed; If the evaporator temperature (tevaporator) of the indoor unit still does
not reach the threshold Tv evaporator 1 minute later, the indoor fan motor will carry out compulsory
operation under high air speed grade for 8 seconds and then operates under set air speed; Refer to the
following figure.
Cold Air Prevention threshold
Model
Cassette and Air Duct Series
Wall Mounted Unit Series
Tv evaporator Table (①)
Tv evaporator
35
39
70
DIGITAL MULTI VRF
CONTROL
After the indoor unit starts heating operation and the fan motor stops for any reason (including
unit starting, defrosting, failure and no demand capacity), the operation of preventing cold air is
carried out before the fan motor starts again.
After the indoor fan motor starts, the operation of preventing cold air is not carried out even if
the tevaporator is less than the threshold Tv evaporator again, except the fan motor stops.
4)
Heating Temperature Compensation
When the air-conditioner operates under standard conditions, the unit group adjusts the capacity
output of the indoor unit according to the set temperature and the air inlet temperature, so as to adjust
the room temperature to the set temperature. If the installation height of the air-conditioner is
somewhat high, the hot air tends to rise to the upper space when heating operation is carried out,
which is the result of difference of density. Now the temperature of the living space may not reach the
set temperature so people may feel uncomfortable.
Therefore, it is required to use the temperature compensation function during heating: the air
inlet temperature minus 2① is adopted to reflect the real temperature of the living space. Using this
method, comfortable temperature will be maintained in the living space.
5)
Anti-Frosting Control Under Cooling and Dehumidifying Modes
To prevent the frosting as a result of low temperature of the evaporator during the operation of
cooling or dehumidifying of the indoor unit from bringing adverse effect to the cooling efficiency, the
indoor unit will carry out anti-frosting operation when necessary.
If it is detected that the evaporator inlet pipe temperature T Inlet is ≤ T Frosting Temperature for T
71
DIGITAL MULTI VRF
CONTROL
minutes after the compressor operates for T Compressor minutes under the modes of cooling or
dehumidifying, the anti-frosting operation will be carried out and now the indoor fan motor and the
swing motor remain the original status; When the T Inlet is ≥ T Recovery Temperature, the indicating light is
off and the controller will operate under set mode.
The parameters T Compressor , T Anti-frosting , T Frosting Temperature ,and T Recovery Temperatureare different for
different unit models. Refer to the following table:
Anti-frosting
Unit Model
6)
T Compressor(m) T Anti-frosting(m)
T Frosting Temperature(①)
T Recovery Temperature(①)
Duct Cassette Series
15
10
-4
15
Wall Mount Series
6
3
0
10
Automatic Swing Control
The wall mount series and the cassette series indoor units have swing function. Using swing
function can increase air convection indoors to increase the uniformity of the indoor temperature.
◆Reset
When the unit is powered on for the first time, the swing louvers will swing automatically once
to let the swing louver return to the initial position, thus the correctness of the swing louver action is
ensured.
◆Using the keys on the indoor unit to turn on the unit
When using the keys on the indoor unit to turn on the unit, the default automatic swing will be
started and the swing louvers swing back and forth from the maximum location and the minimum
location (for different modes, the maximum locations and the minimum locations are different).
◆Using wire controller or remote controller to control
When using the wire controller or the remote controller to turn on the unit and the automatic
swing signal is not set then, the swing louvers will stop at the default position when the unit is turned
on (for different modes, the default locations are different). If the automatic swing signal is set when
the unit is turned on, the automatic swing will be started and the swing louvers swing back and forth
from the maximum location and the minimum location (for different modes, the maximum locations
and the minimum locations are different).
When the wire controller or the remote controller sends the signal of automatic swing, the indoor
unit will start automatic swing and the swing louvers will start to swing from the current location.
When the wire controller or the remote controller sends the signal of stopping automatic swing,
the indoor unit will stop automatic swing operation and the swing louvers will stop at the current
location.
◆Others
When the indoor unit receives the signal of switching-off, detects the failure signals other than
the auxiliary electrical heating protection signal, and detects the defrosting signal, the indoor unit,
regardless of which state the swing louvers are in, will stop to return to the initial position after the
72
DIGITAL MULTI VRF
CONTROL
indoor fan motor stops.
When the indoor unit detects the auxiliary electrical heating protection signal, the automatic
swing will start regardless of which state the indoor unit is in, and the indoor fan motor will operate
under high speed.
7)
Drainage Pump Motor Control
The cassette series indoor unit is equipped with the drainage pump which can drain the
condensate water produced during the cooling or the dehumidifying operation.
◆When the indoor unit carries out cooling or dehumidifying operation, the water pump and the
compressor starts simultaneously.
◆When the unit is turned off or the cooling operation is stopped, or when the dehumidifying
operation is stopped or the unit turns to other mode, the power supply to the water pump will only be
cut off 5 minutes later.
◆When it is detected that the water level overflows for 8 seconds regardless of which mode
(including switching-off of unit) the unit is in, the water pump will start immediately and will not stop
if the signal of water level overflow is not removed; But the water pump will continue operating for
10 minutes further after the signal of water level overflow is removed.
8)
Electronic Expansion Valve Control
A. Reset Control of Indoor Electronic Expansion Valve
When the indoor unit is powered on, the indoor unit will automatically carry out the reset of the
electronic expansion valve, so that the valve return to the initial position to ensure the correctness of
the action of the valve.
B. Control of Superheat Degree During Cooling Operation
During the process of cooling or dehumidifying, the unit group shall control the open degree of
the electronic expansion valve of the indoor unit according to the fact that how the difference between
the inlet temperature and the outlet temperature is deviated from the set superheat degree. The
purpose is to keep proper superheat degree and the detection is carried out every 40 seconds. When
the unit is turned off, the operation of the unit is stopped when the set temperature is reached, or there
is any failure, this control process is ended.
C. Control of Subcooling Degree During Heating Operation
73
DIGITAL MULTI VRF
CONTROL
During the process of heating, the unit group shall control the open degree of the electronic
expansion valve of the indoor unit according to the fact that how the difference between the inlet
temperature and the outlet temperature is deviated from the set superheat degree. The purpose is to
keep proper subcooling degree and the detection is carried out every 40 seconds. When the unit is
turned off, the operation of the unit is stopped when the set temperature is reached, there is any failure
or defrosting is carried out, this control process is ended.
9)
Sensor Inspection Control
◆Ambient Temp. Sensor
When it is detected that the ambient temperature is continuously lower than -20① for 1 minute
or is continuously higher than 100① for 1 minutes, the signal of ambient temp. sensor failure (failure
code: F0) is sent and the indoor unit stops operation because of abnormality.
If it is detected that the ambient temperature is continuously larger than -20① but lower than
100① for 1 minute under the status of ambient temp. sensor failure, the signal of ambient temp.
sensor failure is removed and the indoor unit resumes the original operating status.
◆Evaporator Tube Temp. Sensor
When it is detected that the evaporator tube temperature is continuously lower than -30① for 1
minute or is continuously higher than 100① for 1 minutes, the signal of evaporator tube temp. sensor
failure is sent and the indoor unit stops operation because of the abnormality.
If it is detected that the evaporator tube temperature is continuously larger than -20① but lower
than 100① for 1 minute under the status of evaporator tube temp. sensor failure, the signal of
evaporator tube temp. sensor failure is removed and the indoor unit resumes the original operating
status.
◆All the detection time is not counted.
Failure Type
Failure Code
Indoor Ambient Temp. Sensor Failure
F0
Indoor Inlet Pipe Temp. Sensor Failure
F1
Indoor Intermediate Pipe Temp. Sensor Failure
F2
Indoor Outlet Pipe Temp. Sensor Failure
F2
10) Address Code Setting
Each indoor unit of the same group can only operate normally if it is assigned only one address.
Therefore, the address of the indoor units must be set properly.
Different indoor units of the same group must have different address.
Each group of indoor units has 16 different addresses at most.
The address of every indoor unit must be identical with the address of the corresponding wire
controller.
Use the address DIP switches to set the addresses for the indoor units and the wire controller. The
74
DIGITAL MULTI VRF
CONTROL
DIP switches are located at the main boards of the indoor unit and the wire controller and have be
marked with “Address”.
Refer to the following table for the addresses designated by the DIP switch position status combinations.
DIP Switch Position Status Combinations (4-position DIP
11)
Switch)
Position 4
Position 3
Position 2
Position 1
Address Designation
ON
ON
ON
ON
1
ON
ON
ON
OFF
2
ON
ON
OFF
ON
3
ON
ON
OFF
OFF
4
ON
OFF
ON
ON
5
ON
OFF
ON
OFF
6
ON
OFF
OFF
ON
7
ON
OFF
OFF
OFF
8
OFF
ON
ON
ON
9
OFF
ON
ON
OFF
10
OFF
ON
OFF
ON
11
OFF
ON
OFF
OFF
12
OFF
OFF
ON
ON
13
OFF
OFF
ON
OFF
14
OFF
OFF
OFF
ON
15
OFF
OFF
OFF
OFF
16
Function Code Setting
☆ Before power on of the main board, 4-bit dial switch must be set to decide running status of
indoor unit.
☆
Function description is as below:
The DIP switch setting showed in above illustration is the default setting after manufactured.
75
DIGITAL MULTI VRF
Dial switch
CONTROL
Function description
Silk-screen
Dial ON
Dial OFF
Standby after
Recovery
power on
after power on
Selection of memory mode:
1(S/R)
A. Selection between recovery mode after
power on
and standby mode after power on
B. This function is effective without wired controller.
Selection between receiver and manual controller:
2(L/I)
A. If manual controller is selected; remote-control
Select wired
function of receiver will be shielded.
controller to
B .If receiver is selected, manual controller will be
operate
Select receiver
to operate
ineffective.
Setting of master unit and slave indoor unit
3(M/S)
A. Used to solve modes conflict
Master unit
Slave unit
A. selection between ambient temp. sensor (T amb.) of
Select ambient
Select ambient
main board and ambient temp. sensor (T amb.1) of
temp. sensor of
temp. sensor of
main board
receiver
B. This function is effective without wired controller.
Selection of ambient temp. sensor:
4(I/O)
receiver
This function is effective without wired controller.
5(L/H)
Select to choose high E.S.P or low E.S.P fan speed
Select
low
Select high
E.S.P
fan
E.S.P fan
speed
speed
76
DIGITAL MULTI VRF
CONTROL
3 WIRELESS REMOTE CONTROLLER
NOTE!
● Make sure that there is no obstruction between the remote control and the signal receptor.
● The remote control signal can be received at the distance of up to about 10m.
● Don’t drop or throw the remote control.
● Don’t let any liquid flow into the remote control.
● Don’t put the remote control directly under the sunlight or any place where is very hot.
FAN button
Press the button to
change the speed of the
fan according to the
following order.
SWING
AUTOFAN
TEMP. button
Set temp. increases 1 c
by pressing "+" and
decreases 1 c by pressing
"-" once.
Set temp. : 16 c~30 c
Set temp. : 16 c~30 c
FAN
AUTO FAN
SPEED
OPER
AUTO
AIR
SWING HUMID LIGHT SAVE
TIMER
ONOFF
HR.
COOL
DRY
FAN
HEAT
Set temp. : 16 c~30 c
Set temp. : 16 c~30 c
ON/OFF button
Press the button to turn on
the unit. Press the button
once again to turn off the
unit and cancal the timer.
MODE button
Press the button to change
the mode according to the
following order
MODE
ON/0FF
NOTE: The cooling only
units have no
mode.
NOTE!
After every indoor unit received the turn off signal, the fan and electric inflate valve will
continue to work for 20-70mins to make use of the rest cool or rest heat, while for preparation for the
nest work. And this is normal phenomenon.
NOTE!
This type of remote control is a kind of general use remote control that is suitable for several
types (function) of air conditioner units. Please understand that the functions and buttons that are
not suitable for this air conditioner will not be introduced.
77
DIGITAL MULTI VRF
CONTROL
Liquid crystal displayer
It shows all set contents.
SWING
FAN
AUTOFAN
SLEEP button
Press the button to set SLEEP
mode, and stop when repressed.
When the sleep mode is in the
cool and dry mode, the set
temp. will increases 1~2①
during the set time, then the
unit will operate according to
the temp.. When sleep mode is
in the heat mode, the set temp.
decreases 1~2① during the set
time, then the unit will operate
according to the set temp..
OPER
AUTO
AIR
SWING HUMID LIGHT SAVE
TIMER
ONOFF
HR.
SLEEP
AIR
LIGHT
HUMID
TIMER ON TIMER OFF
MODE
ANION
SAVE
ON/0FF
Temp./Timer button
When the unit is operating, increase 1①
by pressing "+" button once, and
decrease 1① by pressing "-" button
once. The indoor temp. can be set in
the range of 16-30①.
Press the "Timer OFF/TIMER ON"
button at operating/ stopping to set the
off/on time. Press "Timer OFF/TIMER
ON" once to increase 0.5 hour for the
set time. The Max.value of setting time
could be 24 hours,when repressed it
the setting time will be canceled.
Operation procedure
Normal procedure
1. Press ON/OFF button after energization, then the unit is operating.
2. Press MODE button to choose the need operation mode.
3. Press FAN button to set the fan speed.
4. Press +/- button to set the need temp.
Selectable procedure
5. Press SLEEP mode to set the sleep state.
6. Press TIMER OFF button to set the set time.
Note: When the operating mode selected by the indoor unit clashes with the one selected by the
outdoor unit, the remote controller will display the operating clash after 5 seconds and the power
light will flicker, then the indoor unit turns off. At this time, the units will become normal after the
operating mode of the indoor unit is changed to cooperate with the outdoor unit. Cool mode can
cooperate with dry mode, and fan mode can cooperate with any mode.
78
DIGITAL MULTI VRF
CONTROL
How to insert batteries
Two batteries (Two AAA dry-cell batteries) are used by the remote control
1. Remote the cover from the back of the remote control downward, take out the worn batteries and insert
two new ones (Make sure the two poles are correct)
2. Re-attach the cover.
ACL
1.All the prints and code no. will
be showed on the displayer after
the insert of batteries. The remote
control can be operated after 10sec.
2.The lifetime of the batteries is
about one year.
3.Don't confuse the new and worn
or different types of batteries.
4.Remove batteries when the
①Remove the cover remote control is not in use for a
③Re-attach the cover longtime to avoid mal-function
caused by liquid leakage.
5.The remote control should be
placed about 1m or more from the
open
TV set or any other electric
appliances.
6.The remote control should be
used in the receivable range (the
RESET KEY
reception range is 10m)
7.When the remote control can not
be controlled in the situation of
inserted batteries, please remove
the back cover and press "ACL"
button to make it normal.
②Insert 2AAA dry-cell
battaries(attachment)
79
DIGITAL MULTI VRF
CONTROL
4 WIRED REMOTE CONTROLLER
4.1 Operation and Display View
Fig.4.1
Various Components of Wired Remote Controller
1
Operating mode display (Cool, Dry, Fan, Heat)
9
On/Off button
2
Sleep mode display
10
Timer button
3
Environmental temp. display /Malfunction display
11
Sleep button
4
Fan control display (automatic, high, media, low)
12
Swing display
5
Set Temp. display
13
Fan control button
6
Defrosting display
14
Temp./ Timer decrease button
7
Timer display
15
Temp./ Timer increase button
8
Signal receptor
16
Mode button
85
54
42.5
21.5
4.2 Dimension
60
85
Fig.4.3.1 Outline Demension of Wired Controller
Fig.4.3.2 Installation Demension of Wired Controller
80
DIGITAL MULTI VRF
CONTROL
4.3 Installation
1
Fig.4.3
2
3
4
Installation of wire remote controller
SN
1
2
Name
Casing base, installed into the wall
Controller Soleplate
3
Screw
M4X25
4
Controller Panel
● Notice for installation under the guidance of Fig.10
1. Cut off power supply before installing the electrical components, it is forbidden to carry out the installation with power
on;
2. Get one end of the 4 core communication cable, put it through the rectangular hole on the base board of the wire remote
controller;
3. hold the base board of controller on the wall, then fix it to the wall with M4x25 screw;
4. Plug the 4 core communication cable into the slot on the wired remote controller, then fix the controller panel with base
board together;
81
DIGITAL MULTI VRF
CONTROL
5 Mini Centralized CONTROLLER
5.1 Function
Region monitoring control and region wired control are the two main control functions for
mini centralized controller (region controller).
Region monitoring controller can monitor or control 16 indoor units of a group for inquiry and
single or centralized control.
Region wired controller can replace 1-16 selected wired controllers to uniformly set or control the
indoor units.
Refer to Fig.1.1, Fig.1.2 about the Sketch map to the relation among the mini centralized controller
(region controller), region monitoring controller and region wired controller.
Fig.1.1
Before using, the controller functions must be selected by the personnel who perform the installation
according to the requirements of users. Please refer to Project Debugging Setting section for the details.
Note: If the controller is set to be region wired controller, the wired controller of the selected
indoor unit must be removed.
The mini centralized controller (region controller) can be matched with long-distance monitor. As a
region monitoring controller, its control is subject to that of the long-distance monitor. In the same group,
one of the mini centralized controller (region controllers) can be used as region monitoring controller and
matches one or more region wired controller which replace(s) one or more wired controller, in which case,
the region monitoring controller can also monitor or control the region wired controller.
Fig.1.2 Sketch map to the relation among the mini centralized controller (region controller), region monitoring
controller and region wired controller
82
DIGITAL MULTI VRF
CONTROL
5.2 Operation View
(Fig.5.2)
Instruction to functions of buttons (Table 5.1)
No.
1
2
Name
FUNC
(FUNCTION)
MODE
Function
A. Switch the control mode of inquiry/single/ central control.
B. In central control status, give the central order by successively pressing FUNC
button.
Set cooling/heating/fan/dry mode for indoor unit
A. Inquiry status: cycle, increase or decrease No. of indoor units to easily inquire the
3
▲
status of each indoor unit.
B. Single/Central control status: set running temp. of indoor unit, maximum is 30①
and minimum is 16①.
4
▼
5
FAN
C. Timer setting status: increase or decrease the timer on/off time, maximum is 24hr
and minimum is 0.
A. Set the indoor fan speed of hi/mid/low/auto.
B. Successively press FAN button to set on/off swing.
A. Under single/central control mode, set on /off timer of selected indoor unit
6
TIMER
B. Under inquiry status, inquire the timer setting of the indoor unit with current
address.
7
2MODE and
7 ON/OFF
2MODE and
6 TIMER
4 ▼and
6 TIMER
ON/OFF
Set ON/OFF of the indoor unit.
Under single/central control, press MODE and ON/OFF buttons simultaneously to
Lock
start/ stop the lock of operation to buttons of wired controller for selected indoor
units.
Shield mode
Shielding
Temp.
Under single/central control, press MODE and TIMER simultaneously to start/ stop
the shield of operation to MODE button of wired controller for selected indoor unit.
Under single/central control, press ▼ and TIMER simultaneously to start/ stop the
shield of operation to Temp button of wired controller for selected indoor unit.
7 ON/OFF and
Shielding
Under single/central control, press ON/OFF and TIMER simultaneously to start/ stop
6 TIMER
ON/OFF
the shield of operation to ON/OFF button of wired controller for selected indoor unit.
83
DIGITAL MULTI VRF
2
MODE and
3
▲
CONTROL
Memory
mode
4 ▼and
Selection
7 ON/OFF
of
function
Refer to power-off memory function about the details.
A.Check the control mode of region monitoring controller / region wired controller
B.Set the control mode of region monitoring controller / region wired controller
Note:
1.The characters with gray back ground indicate buttons. Following part is the same to it.
2. The time of single press of the button is more than 3s, which means successively-press.
3. There isn‘t the function that the region wired controller shields other indoor wired controller.
5.3 Display View
(Fig.5.3)
No.
Display name
Instruction to display
Inquiry state, “INQUIRY” is displayed.
1
Control mode
Single control state,”SINGLE” is displayed.
Centralized control state, “CENTER” is displayed.
2
Running mode
Each indoor unit running mode is displayed.
3
Error
4
-
5
Fan speed display
6
Swing
Swing running of indoor unit is displayed.
7
Timer
“TIMER ON/OFF” is displayed when setting timer or inquiring timer state.
“ERROR” is displayed during any malfunction to indoor or outdoor unit in a
group.
“- “ is displayed when there is no malfunction to selected indoor unit and the
ambient
temp. is below zero.
Hi, mid, low or auto speed of indoor fan is displayed.
Under inquiry state, No. of online indoor units are displayed and No. of selected
8
No. of indoor unit
indoor unit will blink.
Under single control state, only No. of selected indoor unit is displayed.
84
DIGITAL MULTI VRF
CONTROL
Under centralized state, No. of all online indoor units are displayed.
9
Room temp.
“ROOMTEMP” is displayed for no malfunction, but isn’t for malfunction.
Centralized controller
A. Under inquiry state,” SHIELD” will be displayed when selected indoor unit is
shielded.
10
Shield
B. Under control state,” SHIELD” will be displayed during setting or giving the
shield order.
Region wired controller:” SHIELD” will be displayed when selected units are
shielded during long-distance monitoring.
11
Force
12
① (room temp.)
13
14
Room temp. or error
code
Melt
“FORCE” is displayed when indoor unit is forced to run.
“ ①” is displayed when there is no malfunction.
Room temp. value is displayed during no malfunction to selected indoor or outdoor
unit.
Error code is displayed during malfunction to selected indoor or outdoor unit.
“Melt” is displayed during defrosting.
Region monitoring controller
A: Inquiry state: “LOCK” is displayed when selected indoor unit is locked.
15
Lock
B: Control state: “LOCK” is displayed during setting or giving the lock order.
Region wired controller: “LOCK” is displayed when selected unit is locked in
long-distance monitoring.
16
Set
17
① (set temp.)
18
HR (hour)
19
.5
20
Setting temp. and timer
time
“SET” blinks when the unit is on and commanded.
“SET” is displayed when the unit is on without command.
Set temp. value is displayed when the selected indoor unit is on and not in timer
inquiry or setting status.
“HR” is displayed during timer inquiry or setting.
“.5” is displayed when the timer time value includes 0.5 hr and the unit is during
timer inquiry or setting.
During timer inquiry, integer of setting time of timer is displayed.
During timer setting, integer of setting time of timer is displayed.
Set temp. value is displayed when the unit is not during timer inquiry or setting.
Note:
1. Contents in the double quotation marks indicate the display in LCD. Following part is the same to it.
2. Online indoor units to Mini Centralized Controller indicate that in a region. Following part is the same to it.
3. No signal control function for region wired controller, and “SINGLE” won’t be displayed either.
85
DIGITAL MULTI VRF
CONTROL
5.4 Connection Between Controller and Unit
Insert the 4-core twisted pair line to wired controller. If it is with the indoor unit, insert it into mini
centralized controller (region controller) wiring terminal CN1 (or CN2), and then connect the other wiring
terminal CN2 (or CN1) with the main board of indoor unit.
If there is no wired controller with indoor unit, introduce a 4-core twisted pair line to indoor unit main
board and connect it with mini centralized controller (region controller) wiring terminal CN1 (or CN2).
Note:Any main board of the indoor unit controlled by the mini centralized controller (region controller)
can be connected. If the mini centralized controller (region controller) is used as a region wired controller,
wired controller with the indoor unit must be removed.
Fig2.1 Power cords and communication lines for mini centralized controller (region controller)
Before installation and connection, make sure the power supply is off. After installation and
connection, check the connection result again to prevent loose or short.
There are 4 connection lines (included in the 4-core twisted pair line) to the controller, from CN1 or the
upper and right CN2 to the upper they respectively are: Ground line (GND), communication line A (A),
communication line B(B) and power cord (+12 v).
Note:
During following connection of wirings, pay special attention to them to avoid malfunction to units for
electromagnetic interference.
1. Keep the signal lines or wirings (communication) of mini centralized controller (region controller) or
wired controller at least 20 cm from the power cords or connecting lines between indoors and outdoors to
prevent abnormal communication.
2. Shielding twisted pair line must be adopted as signal line or wiring (communication) once the unit
is installed in the place where there is serious electromagnetic interference.
86
DIGITAL MULTI VRF
CONTROL
6 CENTRALIZED CONTROLLER
6.1 Function
Main characteristics of Centralized Controller:
◆ A set of Centralized Controller can control 64 communication modules and can connect to as
much as 1024 indoor units. It can conduct individual control with any separated area or unified
control. It can monitor or control On/Off, Mode, Temperature setting and Timer On/Off of indoor
unit etc.
◆ It can realize the central, single or select control to all indoor units.
◆ It can organize several indoor units into groups as you desired and conduct unified
control—Group select control.
◆ Error contents are shown by codes. Corresponding communication module numbers of the indoor
units with error contents would blink for rapid inspection and repair (There is sound warning for a
few errors).
◆ Timer function. Every indoor unit can set Timer On/Off time by central, single or select control.
Both Timer On time and Timer Off time can be set at the same time, and it is available to set the
timer to which day among the 7 days from Sunday to Saturday works.
◆ Clock function displays in year, month, day, hour, minute and week, and the clock can be
manually adjusted.
◆ Indoor and outdoor units online auto detect, display and working state indication.
◆ Self-inspection function is remained.
◆ Centralized Controller and several communication modules formed communication net, the length
of communication wire of the net can be as long as 1km (without using communication repeaters).
6.2 Operation View
2
1
3
17
16
15
4
14
13
12
11
10
9
8
7
6
5
(Fig.6.2)
87
DIGITAL MULTI VRF
CONTROL
This central control has Sequence On function, that enable conduction to sequence control
1
ALL ON
to communication modular in interval of 2 seconds, communication modular controls
Sequence On of indoor units (to lower impact to power network).
This central control has Sequence Off function, that enable conduction of sequence control
2
ALL OFF
to communication modular in interval of 2 seconds, communication module controls
3
ON/OFF (2)
4
TIMER
5
SWING
Set if indoor unit swings
6
SPEED
Set fan speeds of High, Medium, Low or Auto for indoor unit
7
MODE
Sequence Off of indoor units (to lower impact to power network).
For controlling units’ on and off.
Set and check the time of Timer On and Timer Off of indoor unit and date mode.
Set modes of Cool, Dry, Fan or Heat for indoor unit
It works as direction and adjusting under every operation function. Such as: When
8
LEFT/RIGHT
checking, it can move to the required indoor unit or communication modular by using this
UP/DOWN
button; when adjusting time, press LEFT (/RIGHT) to shift “Y/M/D” etc. and press UP
(/DOWN) to adjust value
9
CONTROL
10
GROUP
11
TIME
12
SYSTEM/TEST
Under control mode, press this button after setting state of indoor unit, control to indoor
unit would be conducted by corresponding control mode.
Press button under checking state to begin information check and set of grouped indoor
unit, grouped information is for select control.
Set system time
Begin setting of central control run mode, it is not recommended to be used by users.
Shift display domain and indoor wired air condition control. DOMAIN corresponding to
13
INDOOR/DOMAIN
display on line communication modular, INDOOR corresponding to display on line
indoor control.
Press this button during process of setting function to exit the already made function
14
CANCEL
setting operation. Such as, if central control mode were selected, press CANCEL at this
time would back to control mode selecting state.
Begin control setting mode, and Central Control, Select Control and Single Control can be
selected.
15
CONTROL MODE
Central Control: Control all indoor units under domain by present set state.
Single Control: Control present indoor unit by present set state.
Select Control: Control selected indoor unit by present set state, it also called
grouped control
16
SELECT
17
CONFIRM
Select required control or setting object; repress the button to the object is to cancel.
Confirm the operated operation is effective
88
DIGITAL MULTI VRF
CONTROL
6.3 Display View
(Fig.6.3.1)
Sketch for LCD part:
1
3
2
4
5
6
7
16
8
14
15
13 12
11
10 9
(Fig.6.3.2)
1
Pagination/displays
present domain
Under select control mode, group no. that is present controlling is displayed;
Under addresses setting state, present Soft Add is displayed.
Displays the soft address of communication module that the present checking or
2
Present unit no.
controlling indoor unit is belonged as well as the address of indoor unit;
Format: Soft add—Indoor unit add
3
Error
4
Operation mode
5
Speed display
6
Check
7
Operation monitoring and
Displays when there is error at any indoor or outdoor unit.
Displays every operation state mode of indoor unit
Displays High, Medium, Low and Auto speed of indoor unit
Under group control mode, it is displayed when checking grouping information;
Under address setting mode, it is displayed when checking hard address.
When central control works in normal, operation monitoring displays; when control
controlling /monitoring
signal is transmitted, operation monitoring and controlling is displayed.
8
Error code
Displays when abnormal occur on operation state of present indoor unit.
9
System time
Displays present time, format is Y, M, D, H, M and week.
10
Timer setting
Timer On/Off on when Timer On/Off is set to present indoor unit
11
Pre-set temperature
Displays value of pre-set temperature
89
DIGITAL MULTI VRF
12
Ambient temperature
13
Swing and Defrost
14
System setting
15
Control mode
CONTROL
Displays value of ambient temperature of present indoor unit
Displays operation of swing at indoor unit and defrosting at outdoor unit
Setting operation mode of central control. It should be completed by installation
personnel, but not for users.
Displays 3 control modes of Central, Single and Select controls
When Indoor on, addresses of present online indoor unit is displayed;
When domain on, soft address of present online communication module is
16
Displays of soft address
displayed;
Specific location of controlled indoor unit can only be ascertained when soft
address fits Project Installation List.
Instruction to display interface:
System Setting: Including Address Setting and other functions, and it is set when installation
personnel are adjusting units. It is not recommended that users operate it. The usage of this function
requires password.
Address Setting: Since characters from 01 to 64 are fixed as the addresses of controlling
communication modules displayed by central control (hereinafter called soft addresses), and the
addresses of communication modules themselves (hereinafter called hard addresses) are value from
0~254, thus there is address matching problem between central control and controlled communication
module. In order to solve this problem, address mapping setting is required to be conducted before
project adjusting!
6.4 Connection Between Controller and Unit
6.4.1 Communication network
The following is a brief sketch of communication net of multi variable units:
As shown in figure, the ”\” at A are parting lines for communication net. Left side of the “\” is the
communication net between central control and communication module while the right side is that between
multi variable outdoor unit and indoor units. The 2 nets are individual nets.
Before normal use of central control, do conduct addresses setting and adjusting to
communication system by installation personnel. Only after that can the central control offered to be
used by user.
90
DIGITAL MULTI VRF
CONTROL
6.5 Case Study
Take one floor of an office building for example to illustrate wiring and debugging of the centralized
control system. In this floor, there are 2 assembly rooms, 8 offices and 1 monitor room. Refer to the
following illustration for its plane structure.
1)Instruction to Distribution of Unit and Installation of Equipment
This office building has been installed with 2 sets of GMV units, as shown in the table below.
Quantity of
required
Name
Models
communicati
on
modules
Quantity of
indoor
Corresponding rooms of indoor units
units
(pinboard)
Address of
Room
communication
module
Unit1
GMV-R300W2/
D
1(0)
12
1,2
Office 2
3,4
Office 3
01
Office 6
11,12
communication
module
Office 7
2(2)
20
7,8
9,10
Room
D
5,6
Office 5
Address of
Unit 2
indoor unit
Office 1
Office 4
GMV-R620W4/
Address of
Office 8
02
Assembly
room 1
Assembly
room 2
Address of
indoor unit
1, 2
3, 4
1,2,3,4
03
5,6,7,8
91
DIGITAL MULTI VRF
CONTROL
2)Frame Diagram of System Net
92
DIGITAL MULTI VRF
CONTROL
Instruction to Frame Diagram of System Net
Mark A:Outdoor Unit GMV(L)-R300W2/D can be connected with up to 16 indoor units. In this
project, this outdoor unit is connected with the communication module with address of 01 and indoor units
(address 01~12)of office 1-6, corresponding with independent communication Net.2. The mainboard of
outdoor unit is as follow:
Mark B: Outdoor Unit GMV(L)-R620W4/A can be connected with up to 32 indoor units by two
pinboards ,either of which can connect with up to 16 indoor units . What’s more, the quantity of
communication modules used is the same as that of pinboards.
In this project, pinboard 1 is connected with the communication module with address of 02 and indoor
units (address 01~04)of office 7-8, corresponding with independent communication Net.2. Pinboard 2 is
connected with communication module of address 03 and indoor units (address 01~08)of office 1-2,
corresponding with independent communication Net.3. The outdoor figure is as follow:
93
DIGITAL MULTI VRF
CONTROL
Mark C: Centralized controller cabinet is mainly used to put communication modules together. Refer
to Section 3 Instruction to Installation Procedure of System about its figure and connection method of
communication modules.
Mark D: Centralized Controller ZJ701. For the first use of it, address mapping setting must be made
to specify addresses of communication modules which should be controlled. In this project example there
are 3 communication modules with the address of 01, 02 and 03 which are displayed in the centralized
controller correspondingly.
Mark S1, S2, and S3: Telephone 3-way triple adapters are used to connect communication modules
with communicating net of indoor and outdoor units. Refer to Section 3 Instruction to Installation
Procedure of System for its connection method.
3) Instruction to Installation Procedure of System
z Step 1: Integral Design of the Whole System.
In consideration of features of building and installation of the unit, the building is divided into a lot of
monitoring regions and then confirm required systems, their quantity and installation locations. As for this
example:
A. Division of monitoring regions: According to needs of the users, the whole floor is divided into 3
monitoring regions, south area (office 1-6), north area (assembly room1-2 and office 7-8) and monitor
room.
B. Confirmation of quantity of systems
Name
Qty
Installation Location
Notes
The quantity required for the pinboards is the
Communication
modules
3
Centralized control cabinet
same as communication modules. If no pinboard,
only one module is needed. So, there should be 3
modules in total.
94
DIGITAL MULTI VRF
Centralized control
cabinet
Centralized
controller
CONTROL
1
Monitor room
Installed indoors according to user’s conditions.
1
Monitor room
Installed indoors
z Step 2: Wiring and Installation
A. Centralized controller as extension function of GMV unit can be installed and debugged after
communication connection between outdoor unit and indoor unit and normal operation of the unit.
B. Make of centralized control cabinet
If a lot of communication modules are used, centralized control cabinet is recommended. Heavy
current wires and communication lines should be wired separately. The distance between them
should keep above 15cm.The following figure is an example of centralized control cabinet, but its
design should be based on quantity of communication modules.
C. Connection of communication modules
COM 1 of communication module can connect with indoor and outdoor unit. The two COM2
can connect with other communication module or centralized controller. As shown in the following
figure:
D. Connection between communication module and indoor and outdoor units
According to the net diagram, connect the communication line between indoor unit and
outdoor unit. Then cut off the communication line between the mainboards of indoor unit and
95
DIGITAL MULTI VRF
CONTROL
outdoor unit, as shown below.
Align the cutting terminals and terminals of communication line to COM1, as shown below:
In this case, there are two methods of connecting them.
Method 1: Welding
Weld the two cutting terminals by yellow to yellow and brown to brown, as shown below:
And then weld the terminals of communication line to COM1 with the welding spots in the
above figure together by yellow wire to brown wire, as shown below:
96
DIGITAL MULTI VRF
CONTROL
At last, wrap the welding spots with insulating tape and test conduction performance of the
three communication lines, as shown below:
Method 2: Triple adapter
Make crystal heads for the three lines. The connection direction should be the same as in the
above welding figures, i.e. yellow to yellow and brown to brown wire of indoor and outdoor units,
but yellow to brown wire of communication line to COM1.The crystal heads are as follows:
Insert the three crystal heads into the triple adopter and test conduction performance of them, as shown
below:
97
DIGITAL MULTI VRF
CONTROL
E. Connection of Communication Modules and Centralized Controller
Connection of COM1 of communication module which has 3 COM in total has been
introduced as the above. COM2 can connect with another communication module or centralized
controller, as shown below:
Note: The above figure is only for reference to relation among the equipments. The actual wiring is
subject to the above frame diagram of system
● Step 3: There are two methods of DIP address setting of communication module
Method 1: The address of each communication module has been fixed in the factory and marked on
the label at the back of it. It is unnecessary for users to set anything. In addition, the 3-digital DIP can not
be dialed to OFF completely, as shown below:
Label for address of
communication module
98
DIGITAL MULTI VRF
CONTROL
Method 2: Manual setting of address, as operated the following:
1. Dial the digital switch at the back of communication module to OFF completely, as below:
Dial the 3 rods to OFF.
2.Open the cover of communication module as below:
The 8-digital DIP is as below:
99
DIGITAL MULTI VRF
CONTROL
Set DIP for address according to the following table.
Address from 0 to 31
DIP S2
Address from 32 to 63
Address
DIP S3
1
2
3
4
5
1
2
3
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
1
1
0
0
0
0
0
1
0
1
0
1
0
1
1
DIP S2
Address
DIP S3
1
2
3
4
5
1
2
3
0
0
0
0
0
0
1
0
0
32
0
1
1
0
0
0
0
1
0
0
33
0
0
2
0
1
0
0
0
1
0
0
34
0
0
0
3
1
1
0
0
0
1
0
0
35
0
0
0
0
4
0
0
1
0
0
1
0
0
36
0
0
0
0
0
5
1
0
1
0
0
1
0
0
37
1
0
0
0
0
0
6
0
1
1
0
0
1
0
0
38
1
1
0
0
0
0
0
7
1
1
1
0
0
1
0
0
39
0
0
0
1
0
0
0
0
8
0
0
0
1
0
1
0
0
40
1
0
0
1
0
0
0
0
9
1
0
0
1
0
1
0
0
41
0
1
0
1
0
0
0
0
10
0
1
0
1
0
1
0
0
42
1
1
0
1
0
0
0
0
11
1
1
0
1
0
1
0
0
43
0
0
1
1
0
0
0
0
12
0
0
1
1
0
1
0
0
44
1
0
1
1
0
0
0
0
13
1
0
1
1
0
1
0
0
45
0
1
1
1
0
0
0
0
14
0
1
1
1
0
1
0
0
46
1
1
1
1
0
0
0
0
15
1
1
1
1
0
1
0
0
47
0
0
0
0
1
0
0
0
16
0
0
0
0
1
1
0
0
48
1
0
0
0
1
0
0
0
17
1
0
0
0
1
1
0
0
49
0
1
0
0
1
0
0
0
18
0
1
0
0
1
1
0
0
50
1
1
0
0
1
0
0
0
19
1
1
0
0
1
1
0
0
51
0
0
1
0
1
0
0
0
20
0
0
1
0
1
1
0
0
52
1
0
1
0
1
0
0
0
21
1
0
1
0
1
1
0
0
53
0
1
1
0
1
0
0
0
22
0
1
1
0
1
1
0
0
54
1
1
1
0
1
0
0
0
23
1
1
1
0
1
1
0
0
55
0
0
0
1
1
0
0
0
24
0
0
0
1
1
1
0
0
56
1
0
0
1
1
0
0
0
25
1
0
0
1
1
1
0
0
57
0
1
0
1
1
0
0
0
26
0
1
0
1
1
1
0
0
58
1
1
0
1
1
0
0
0
27
1
1
0
1
1
1
0
0
59
0
0
1
1
1
0
0
0
28
0
0
1
1
1
1
0
0
60
1
0
1
1
1
0
0
0
29
1
0
1
1
1
1
0
0
61
0
1
1
1
1
0
0
0
30
0
1
1
1
1
1
0
0
62
1
1
1
1
1
0
0
0
31
1
1
1
1
1
1
0
0
63
100
DIGITAL MULTI VRF
CONTROL
Address from 64 to 95
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
2
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
DIP S2
3
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
4
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Address from 96 to 127
DIP S3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Address
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
2
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
DIP S2
3
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
4
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DIP S3
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Address
3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
z Step 4: System Setting of Centralized Controller
SYSTEM SETTING includes ADDRESS SETTING and INITIALIZE SETTING. The former one
is used for setting address of control object (communication module), and the latter one for
initializing the data in the centralized controller (including clear all the finished address settings).
Since the centralized controller can control at most 64 communication modules and the
address of them is 0 to 253 (0 is generally unused), it is necessary to specify the address of
communication module needed to be controlled. It is ADDRESS SETTING, which is not
recommended to operate by users.
The debugging personnel can press SYSTEM/DEBUG into system setting interface. After
pressing UP, DOWN, LEFT and RIGHT buttons, press CONFIRM button into the interface for
selection between ADDRESS SETTING and INITIALIZE SETTING.
The operation procedure of ADDRESS SETTING:
1. The centralized controller without energizing and setting will display following.
Display Present Unit No. 00-00 which means soft address 00-No. 00 indoor unit. (Soft
101
DIGITAL MULTI VRF
CONTROL
address is the No. displayed in 1-64 grid of LCD.
Press SYSTEM/DEBUG into system setting interface. After pressing UP, DOWN, LEFT
and RIGHT buttons, press CONFIRM button into the interface for selection between
ADDRESS SETTING and INITIALIZE SETTING. Then press UP or DOWN button to switch
between them.
2. When ADDRESS SETTING is blinking, press SELECT button into address setting
interface.
Hard address
Soft address
Press LEFT or RIGHT button to switch between SOFT and Hard ADDRESS settings, and
UP or Down button to adjust their values。After adjustment, press CONFIRM button to make
the address values corresponding and effective. If the cursor stops at hard address position
(hard address is blinking), press CANCEL button to make the setting value ineffective, in
which case, the “- -”will be displayed.(Soft address is the No. displayed in 1-64 grid of LCD
and hard address is the actual one of communication module.)
In this example, the centralized controller controls 3 communication modules with the
address of 01, 02 and 03 (i.e. hard address is 01,02 and 03).For convenient management,
soft address will be set to the same as hard address, i.e. “01 001”, “02 002”and “03 003”.
If communication is normal after setting, the centralized controller will display as the
following figure:
Soft address
display 01,02
Press
and 03
check indoor unit status
under
this
button
to
corresponding
soft address.
01,02 and 03 of soft address is displayed, which indicates normal communication of these
3 communication modules.
II. PRESENT UNIT NO. displays “01-08”, which indicates No. 08 indoor unit under 01
communication module is being checked.
I.
102
DIGITAL MULTI VRF
CONTROL
III.Press ROOM/REGION button to check other indoor units’ status under present
communication module. Indoor units’ status is automatically detected, without setting in
centralized controller.
z Step 5: Troubleshooting during Installation of Centralized Controller
Generally speaking, connection of communication lines, address DIP of communication
module and address mapping setting of centralized controller are the common problems during
installation of centralized controller. These problems can be reflected from running indicator (green)
of communication module. Meanwhile, it is recommended to debug the centralized controller after
making communication of outdoor and indoor units smooth to simplify the problems.
A. Connection of communication lines
① If incorrect or non-connection of communication module, centralized controller and
communication line of indoor and outdoor units, the green indicator will be black all the time.
② It indicates connection problem between communication module and centralized controller
that green indicator blinks once every 2s.In this case, COM2 must be used to connect them.
③ It indicates connection problem of communication module and indoor and outdoor units
that green indicator blinks twice every 2s. In this case, COM1 must be used to connect them.
Refer to Step 2, C for details.
B. Address DIP of communication module
There are two methods for address setting. The one is that communication module has
been set by software store, but the 3-digital DIP switch can not be dialed to OFF completely.
The other one is to set it manually, but the 3-digital DIP switch should be dialed to OFF
completely. Refer to step 3 for details.
C. Address mapping setting of centralized controller
The centralized controller only can normally operate after specifying address of
communication module needed to control. If not, the operation status of communication and
indoor units can not be displayed by it. Refer to Step 4 for details.
103
DIGITAL MULTI VRF
CONTROL
7 MONITORING SOFTWARE
7.1 Function
With the development and improvement of manufacturing technology and in order to solve the
problems of complex distribution of the central AC in the buildings and difficult control and maintenance
of them, an platform easy and reliable to operate must be provided to the users for daily management and
maintenance. So this long-distance monitoring system combining electronic communication and computer
technologies is developed to collect the running state of the units and to monitor and control the units from
a long distance. Its structure is as follow:
7.2 Connection Between the Computer and the Unit
Notice:
z The address code of the communication modules should not be conflicted in one project.
z Optoelectronic Isolated Repeater :One every 800m of communication distance equipped with one and
One every 30 communication modules equipped with one.
104
DIGITAL MULTI VRF
z
z
z
CONTROL
the communication cable and heavy-current wire should be separated and the distance between them
can not be below 15cm
line A and line B of Bus 485 should respectively correspond with line A and line B.
crystal head(crystal head buckle is downwards)
Wiring Diagram
Description of above communication cables
Cable
Description
D1
crystal head and the other end is XH 4-core pin connector(2-core Type-V twisted pair wire)
D2
both crystal head(Standard parts)
D3
crystal head and the other end connects of it connects with wiring terminal of converter.
(2-core Type-V twisted pair wire)
H2
both 9-core head (Standard parts)
105
DIGITAL MULTI VRF
CONTROL
7.3 Hardware
1. Introduction to Main Devices
1.1 R232-R485 Optoelectronic Isolated Converter (standard parts)
1)Function Introduction:
z R232-R485 optoelectronic Isolated converter is used to convert the signal 232 of PC COM
and signal of bus 485.
2)Dimension
Description
L(mm)
W(mm)
H(mm)
optoelectronic isolated converter
94
72
23
3)Installation Dimension
106
DIGITAL MULTI VRF
CONTROL
4)Installation Criteria:
z It must be installed indoors to avoid knock, insolation or rainwater and is better to be put in
the monitoring room.
z This device must be the original one in the factory. Never self-buy the models for
replacement.
z 220-V AC socket must be installed for independent power supply.
z Power supply specification: 12~30VDC 800mA
1.2 Optoelectronic Isolated Repeater(optional parts)
1)Function Introduction:
z Optoelectronic Isolated repeater is mainly used for collecting increase of communication
distance and nodes when the quantity of communication modules is above 30 or
communication distance is above 800m.Refer to Project and Installation section for details.
z 2)Dimension
107
DIGITAL MULTI VRF
CONTROL
Description
L(mm)
W(mm)
H(mm)
Optoelectronic Isolated Repeater
94
72
23
3)Installation Dimension
4)Installation Criteria:
z It must be installed indoors to avoid knock, insolation or rainwater and is better to be put in
centralized control cabinet
z This device must be the original one in the factory. Never self-buy the models for replacement.
z 220-V AC socket must be installed for independent power supply.
z 12~30VDC 800mA Power supply specification: 12~30VDC 800mA
1.3 Communication Module (standard parts)
1)Function Introduction
z Communication module is used for conversion and transfer of signal of PC and air
108
DIGITAL MULTI VRF
CONTROL
conditioner during the communication of them, making the role of communication
controller. Refer to User Instruction to Communication Module for details.
2)Dimension:
Description
L(mm)
W(mm)
H(mm)
Communication module
150
102
30
3)Installation Dimension:
Description
Hanging Hole
Distance to top side(mm)
35
Diameter(mm)
5
4)Use Instruction to Communication Module
z
The Sketch Map of COM, as shown below:
Power
z Use Instruction
Please check the user manual of communication module for details information.
5)Installation Criteria of Communication Module:
z Ensure the specification of power adapter to avoid malfunction or damage to the communication
module.
z Ensure unique DIP address of each communication module in the project to avoid malfunction.
109
DIGITAL MULTI VRF
CONTROL
z Ensure communication cable connects with correct COM to avoid malfunction.
z The communication modules should be put in centralized control cabinet together to avoid direct
sunlight or high temperature and wet environment.
z Power transformer specification: input AC200V~50HZ and output DC9V~800mA
110
DIGITAL MULTI VRF
CONTROL
1.4 Centralized Control Cabinet (user provided parts)
1)Function Instruction:
z The communication modules can be put together for convenient centralized management
and reliable operation.
2)Dimension:
z The following dimension is for reference. The cabinet is designed according to 10
communication modules into. If more modules are needed, the cabinet should be designed
once again. The internal structure should accord to actual state.
The external dimension of the cabinet (Unit: mm)
3)Installation Criteria:
z
z
z
z
The dimension of the cabinet should be designed according to quantity , arrangement and
location of the communication modules before make of it.
Independent power supply for each communication module is needed, so enough 220v AC
sockets should be installed in the cabinet.
The communication cable and heavy-current wire should be separated for the distance above
15cm.
The cabinet should be put indoors and locked to avoid insolation and rainwater or contact of
non-manager.
111
DIGITAL MULTI VRF
CONTROL
1.5 3-way Phone Connector(user provided parts)
Note: Lines without 3-way telephone connector can be connected by welding and protected with
insulating tape to avoid oxidization and short circuit.
1)Function Instruction: Common 3-way phone connector is applied to connect 3 pieces of
communication cable.
Dimension :
Description
L(mm)
W(mm)
H(mm)
3-way connector
33
27
21
2)Installation Criteria:
z
z
z
z
z
Avoid knock, insolation or rainwater.
Ensure tightness of each bayonet without load.
Perform conduction test after installation. Replace the ones of poor contact.
The welding method is better than 3-way connector.
After the connection of communication cables with 3-way connector, it must be fixed by
insulating tape to avoid loose and poor contact of crystal head.
112
GREE COMMERCIAL AIR CONDITION
DIGITAL MULTI VRF
INSTALLATION
113
DIGITAL MULTI VRF
INSTALLATION
INSTALLATION
1 PRECAUTIONS FOR INSTALLATION
1.1 Precautions for Installation
Before installation, please ensure if the installing site, power ratings, possible operating range (pipe
distance, height difference between indoor and outdoor unit, power voltage) and installing space are correct
and suitable. The outdoor unit is general to all models according to its power.
‹ To ensure correct installation, please make sure to read the Safety Considerations thoroughly before
starting the installation works.
‹
The considerations stated below are classified into
WARNING and
CAUTION. Those that
might cause death or severe injury in case of wrong installation are identified in
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
WARNING.
CAUTION may also cause severe accidents sometimes.
However, those that are stated in
Therefore, both of them relate to important safety considerations and must be strictly followed..
After completing the installation and test run and confirming that all are normal, please introduce to
the client on how to use and repair the machine according to the Operating Instructions. Besides,
please deliver the considerations herein to the clients together with the Operating Instructions, and
ask them to keep properly.
WARNING!
The installation shall be performed by the vendor or professional dealer from which you buy the
machine. If you install by yourself, any improper installation might cause water leakage, electric
shock or fire accident.
The installation shall be done correctly according to installation instructions. Improper installation
may cause water leakage, electric shock or fire.
To install a large air-conditioning system in a small room, please make sure to take measures to
prevent that the refrigerant will not exceed the limit concentration in case of leakage. For the
measures to prevent the refrigerant from exceeding the limit concentration, please consult your
dealer. If no proper measures, it might cause human suffocation in case of refrigerant leakage.
Please install at a position that is strong enough to support the weight of machine. If the installing
position is of low strength, the machine may drop down and thus cause human injury.
Please carry out installation in accordance with the rules for preventing the typhoon or earthquake.
The machine may tip over if the installation does not comply with the requirements.
The electrical cabling shall be carried out by qualified electricians in accordance with the Safety
Code for Electrical Equipment, relevant local rules and the installation instructions. Make sure to
use the special-purpose circuit. If the power circuit capacity is low or the construction is improper, it
might cause electric shock or fire accidents.
Please use suitable cables and connect them securely. Please fix the terminal joints securely. The
terminal connection shall not be affected due to any external force applied onto the cable. Improper
connection and fixing may cause heating and fire accidents.
Keep the cables in correct shape and prevent them from protruding upward. Please protect them
securely with repair board. Improper installation may cause heating and fire accidents.
When erecting or relocating the air conditioner, do not let any air enter into cooling circulation
system except the specified refrigerant. If any air is mixed, abnormal high pressure will occur in the
cooling circulation system, thus causing crack or human injury accidents.
During installation, please always use the attached parts or designated parts. Failure to use the
designated parts may cause water leakage, electric shock, fire or refrigerant leakage.
CAUTION:
Please earth securely. Do not connect the earth wires to gas pipe, water pipe, lightning rod or
telephone line. Improper earthling might cause electric shock.
Leakage circuit breaker must be installed at some place. No installation of leakage circuit breaker
might cause electric shock.
114
DIGITAL MULTI VRF
‹
‹
INSTALLATION
Do not install at a place where inflammable gas might leak. Gas leakage and despot around the
machine might cause fire accidents.
To ensure correct drainage of water, the drainage pipe shall be installed according to the installation
instructions. Also the heat insulation shall be provided to avoid condensing. Improper installation of
the pipe might result in water leakage and lead to possible wetting of the articles in the room.
115
DIGITAL MULTI VRF
INSTALLATION
1.2 Key Points of Installation
Installation Procedures
Description and Acceptance Criteria
1.
The materials specified on the engineering drawing shall be
purchased as specified (e.g. copper tube, thermal insulation
tube, PVC pipe, power cables, air switch, etc);
Material Selection and Equipment Inspection
2.
The materials not specified on the engineering drawing shall be
purchased according to the actual quantity of works (e.g. hanger
frame, cable duct, etc);
3.
Check if the outdoor unit, indoor unit, communication wires and
accessories are complete.
1.
The power cables shall be separated from communication wires
at a least distance of 10cm.
2.
Connection
strong force.
3.
Communication
To avoid breaking the communication wires, please do not use
For multiple units, please mark them properly.
Switch on indoor and outdoor unit, and ensure there is no display of
wire
“Communication Wire Error E6”
1.
dial code.
Address dial
code
Each indoor unit under the same system has a unique address
2.
The wired controller and its corresponding indoor unit have the
same address dial code.
Installation
of
unit
Remote Control
1.
Select the remote control mode;
2.
The centralized controller and communication module shall be
installed free from the source of interference.
indoor
Power cord
1.
The power cable must meet the specifications.
2.
The indoor units under the same system must be arranged under
unified power supply.
Installation
Drainage Pipe
1.
The PVC pipes must meet the specifications.
2.
A specific gradient must be provided along the water flow
direction.
3.
Carry out water detection after installation.
Carry out thermal insulation to the drainage pipe only after the water
detection is accepted.
Thermal
1.
The thermal insulation tube must meet the specifications.
insulation
2.
Seal between the thermal insulation pipes to avoid air entry.
1.
Design the length of air duct according to static pressure;
2.
The air inlet shall be optimally designed to avoid too small size
Installation of Air Duct (when
with
high
duct-type unit)
static
pressure
116
DIGITAL MULTI VRF
INSTALLATION
1.
The copper tube must meet the specifications.
2.
Ensure it is dry and clean inside the tube.
3.
Make sure to charge nitrogen as required for protection when
welding the tubes.
Welding
4.
Please keep to the welding process and ensure the system free of
leakage.
Installation
5.
Add a dual-way filter on liquid pipe side
of
6.
For multiple systems, please mark them properly.
connection
Carry out leakage detection under pressure after welding.
pipes
1.
Purge the system clean.
2.
Keep the pressure for 24 hours
Purge
and
make
leakage
detection under pressure
Except for the influence by temperature, it is deemed acceptable if
pressure drop is within 0.02MPa. (With the temperature change by
1①, the pressure will change by approx. 0.01MPa)
Thermal insulation
Installation of outdoor unit
1.
The thermal insulation tube must meet the specifications.
2.
Seal between the thermal insulation pipes to avoid air entry.
1.
Select the installing position correctly.
2.
Build the foundation according to the anchor bolt position and
the dimension of outdoor unit
3.
Build the damping device properly.
4.
Avoid sharp knock when handling the outdoor unit. The
inclination angle shall not be higher than 15°
Connection of indoor unit and outdoor unit
1.
Tighten the nuts;
2.
Provide proper protection to the outdoor connection pipe,
communication wires and power supply.
Keep the pressure for 24 hours. Except for the influence by
Leakage detection under pressure
temperature, it is deemed acceptable if pressure drop is within
0.02MPa. (With the temperature change by 1①, the pressure will
change by approx. 0.01MPa).
1.
Establish vacuum simultaneously in the gas pipe and liquid
pipe;
Vacuuming
2.
The vacuuming time shall be long enough.
Put still for 1 hour after vacuuming. It is deemed acceptable if the
pressure will not rise.
Add refrigerant
Add refrigerant according to the volume as specified on the
engineering drawing.
Open the valve of outdoor unit
Commissioning of complete unit
Remarks: 1) Described above are general working procedures. The procedures might vary with the site conditions.
2) For detailed installation rules, please see the description in each chapter.
117
DIGITAL MULTI VRF
INSTALLATION
2 FLOW CHART OF INSTALLATION
Design
Kicking-off
设计交底
材料的选购
Material selection
Inspection of site
现场安装位置审核
installation position
Installation of indoor unit
Installation of
connection pipes
安装室内机
安装连接管
Installation of outdoor unit
安装室外机
Welding
焊接
Installation Connection Connection Installation
of remote 连接
drainage
of
of power of安装
安装远
连接
control
pipes
communica
cables
程监控 通讯线
tion wires 电源线 排水管
Address dial code
地址拨码
Thermal
insulation
保温
Connection of indoor unit and outdoor unit
连接室内机和室外机
Test run of
indoor unit
室内机
试运行检查
Purge and make
leakage detection
under pressure
吹洗和保压检漏
Welding
焊接
Connection of
power cables
连接电源线
Address dial code
保温
Connection of indoor unit and outdoor unit
连接室内机和室外机
Leakage detection
under pressure
保压检漏
Vacuuming
抽真空
Air flow and noise
level inspection
风量
噪音检查
Add refrigerant
追加制冷剂
Open the valve
打开阀门
Commissioning of
complete unit
机组调试
As-built Drawing
竣工图
Delivery of the Operating
Instructions
交付使用说明书
118
DIGITAL MULTI VRF
INSTALLATION
3 INSTALLATION OF OUTDOOR UNIT
3.1 Hoisting of Unit
Transport the unit to a place as close as possible to the installing site before taking it out of the packaging
box.
CAUTIONS!
Never put any object on top of the unit before and after installation.
To lift the machine with crane, please use two ropes to lift the outdoor unit.
◆ Hoisting Method
The machine must be balanced when it is lifted. Check and ensure that the machine can be lifted up safely
and stably.
CAUTIONS!
Do not attach the ropes to the lower wood frame of the packaging box.
Never remove any packaging materials.
As shown, insert two ropes through the square holes on the machine and protect the machine with batten
and corrugated paper.
不得拆去木头框
Never remove
the wood
frame and 架与塑料绑带
plastic straps.
绳索
Rope
The angle between rope
绳索与机器之间的角
and
machine shall be
度要大于60度
higher
than 60º.
Tie the ropes the batten and
将绳索捆在厚度超过15毫
corrugated
paper with a
米的木条板和波形纸板上
thickness
not over 15mm.
Do not apply any
不要在这块板上施加
force to this board
任何力(两面)
(both
sides).
Insert
the ropes through
将绳索从方形孔中穿过
square hole.
◆ During lifting, the position of ropes is as shown below.
◆ Move the lower wood frame of the packaging box away and lift the unit to correct position.
Rope
绳索
Rope
绳索
Square
hole
方形孔
Square
hole
方形孔
Correct
正确
Wrong
错误
3.1.1 Cautions for installation of side outdoor unit
To ensure good operation of the air conditioner, the selection of installing position must be in accordance
with the following principles:
‹ The outdoor unit shall be so installed that the air discharged out of the outdoor unit will not flow back
and that enough space shall be maintained around the machine for repair.
‹ The installing position shall be in good ventilation, so that the machine can breathe and exhaust
119
DIGITAL MULTI VRF
INSTALLATION
enough air. Ensure that there is no obstruction at the inlet and outlet of the machine. If any, please
remove the obstructions blocking the air inlet and outlet.
‹ Also ensure that the outlet air and noise from the air conditioner will not affect the neighbors.
‹ The outdoor unit must be lifted by using the designated lift hole. During lifting, take care to protect
the air conditioner and avoid knocking the metal parts, thus to prevent rusting in the future.
‹ Avoid direct sunshine as it might be.
‹ The installing position must be able to drain the rainwater and the water generated from defrosting.
‹ The installing position must ensure that the machine will not be buried in the snow or affected by the
wastes or oil mist.
‹ To meet the noise and vibration requirements, the outdoor unit shall be installed by using rubber
damping pad or spring damper.
‹ The installing dimension shall comply with the installation requirements in these instructions. The
outdoor unit must be fixed at the installing position.
‹ The installation shall be done by specialist technicians.
3.1.2 Cautions for installation of up outdoor unit
To ensure good operation of the air conditioner, the selection of installing position must be in accordance
with the following principles:
‹ The outdoor unit shall be so installed that the air discharged out of the outdoor unit will not flow back
and that enough space shall be maintained around the machine for repair.
‹ The installing position shall be in good ventilation, so that the machine can breathe and exhaust
enough air. Ensure that there is no obstruction at the inlet and outlet of the machine. If any, please
remove the obstructions blocking the air inlet and outlet.
‹ Also ensure that the outlet air and noise from the air conditioner will not affect the neighbors.
‹ The outdoor unit must be lifted by using the designated lift hole. During lifting, take care to protect
the air conditioner and avoid knocking the metal parts, thus to prevent rusting in the future.
‹ Avoid direct sunshine as it might be.
‹ The installing position must be able to drain the rainwater and the water generated from defrosting.
‹ The installing position must ensure that the machine will not be buried in the snow or affected by the
wastes or oil mist.
‹ To meet the noise and vibration requirements, the outdoor unit shall be installed by using rubber
damping pad or spring damper.
‹ The installing dimension shall comply with the installation requirements in these instructions. The
outdoor unit must be fixed at the installing position.
‹ The installation shall be done by specialist technicians.
3.2 Selection of Installation Site
‹ The place with no residual air
‹ The place where the accessories can be securely fixed
‹ The place where the air will not obstruct the water inlet pipe or water outlet pipe
‹ The place that goes beyond the heating range of other heat sources
‹ The place where the wastewater can be safely drained
‹ The place where the noise and hot air will not affect the neighbors
‹ The place where the snow will not be piled
‹ The place where the water outlet pipe will not be blown by strong wind
Notes:
‹ Do not use guardrail on four sides. Leave 1m at least above the machine.
‹ In case of short-circuit risk, please install an adaptor changeable in air direction.
‹ To avoid short circuiting, please provide adequate suction space when multiple machines are to be
installed.
‹ In the region with snow, the machine shall be installed in a frame or beneath the snow guard, thus to
prevent snow piling on the machine.
‹ Do not install the equipment in a region where any inflammable gas might leak.
﹡The snow guard and other devices shall be designed and installed by the user.
120
DIGITAL MULTI VRF
INSTALLATION
3.3 Dimensions Data
Appearance of GMV(L)-R120W/Na-K, GMV(L)-R160W/Na-M
Unit: mm
Model
A
B
C
GMV(L)-R120W/Na-K
1100
340
1250
GMV(L)-R160W/Na-M
1100
340
1250
Appearance of GMV(L)-R260W2/Na-M, GMV(L)-R300W2/Na-M
Unit: mm
Model
A
B
C
H
GMV(L)-R260W2/Na-M
990
840
880
1772
GMV(L)-R300W2/ Na-M
990
840
880
1772
121
DIGITAL MULTI VRF
INSTALLATION
Appearance of GMV(L)-R450W3/Na-M
Appearance of GMV(L)-R560W4/Na-M, GMV(L)-R600W4/Na-M
Unit: mm
Model
A
B
C
H
GMV(L)-R560W4/Na-M
1980
840
920
1760
GMV(L)-R600W4/Na-M
1980
840
920
1760
122
DIGITAL MULTI VRF
INSTALLATION
Appearance of GMV(L)-R860W6/Na-M, GMV(L)-900W6/Na-M
123
DIGITAL MULTI VRF
INSTALLATION
3.4 Installation Space Requirements
① Clearance data of single unit
GMV(L)-R120W/Na-K, GMV(L)-R160W/Na-M Outdoor Unit Installation Space Dimension
GMV(L)-R260W2/Na-M, GMV(L)-R300W2/Na-M Outdoor Unit Installation Space Dimension
Electrical Box.
Outlet on this side.
GMV(L)-R450W3/Na-M Outdoor Unit Installation Space Dimension
Electrical Box
124
DIGITAL MULTI VRF
INSTALLATION
GMV(L)-R560W4/Na-M, GMV(L)-R600W4/Na-M Outdoor Unit Installation Space Dimension
Air
GMV(L)-R900W6/Na-M Outdoor Unit Installation Space Dimension
Outdoor unit shall be installed on a concrete base 10cm high.
② Clearance data of multiple unit
★Arranged alongside on left and right
◆Air outlet side open
300(150)
300(150)
or
over
或以上
125
DIGITAL MULTI VRF
INSTALLATION
◆Obstructions on air outlet side
500
500
or
over
或以上
300(150)
300(150)
or
over
或以上
★Arranged on front and back
1500
or over
1500或以上
1500
or over
1500或以上
300(200)
300(200)
or或以上
over
600(500)
600(500)
or
over
或以上
★Arranged alongside left / right and front / back
126
DIGITAL MULTI VRF
INSTALLATION
★Arranged by layer on upper and lower
200 or above
500 or above
500 or above
Bench
To ensure good ventilation, the top of unit shall be kept open and free of any obstructions. In case that
the front side and left side (or right side) of the outdoor unit is open space
The unit shall be installed in the same direction.
No restriction to wall height
Rear
Front
Rear
Front
Distance to another outdoor unit
beside
Max. three machines in line
127
DIGITAL MULTI VRF
INSTALLATION
Installed back against back
No restriction to wall height
Front
Rear
Rear
Front
Max.
threemachines
machines in
Max.
three
inline
line
Distance to another outdoor
unit beside
In case there are walls on four sides of the outdoor unit:
It is suggested to install the unit in the same direction.
No restriction to wall height
Rear
Front
Rear
Front
Max. three machines in line
3.5 Take Monsoons and Snow into Consideration
The monsoon shall be taken into consideration when installing the outdoor unit.
正确
Correct
正确
Correct
Incorrect
不正确
Protective
防护罩
cover
Fresh air
新风吸入口
Fresh
air suction
新风吸入口
suction side side一侧(后侧)
(back side)
一侧(后侧)
(back side)
新风吸入口
Fresh
air suction
一侧(后侧)
side
(back side)
新风吸入口
Fresh
air suction
side
(back side)
一侧(后侧)
The
defrost time will be extended
在这种情况下,化霜时间会延长
under this condition.
128
DIGITAL MULTI VRF
INSTALLATION
The snow shall be taken into consideration when installing the outdoor unit.
To prevent the snow from covering the air outlet and air inlet, it is required to use an protective cover on
air outlet and air inlet, and use a higher foundation base.
Correct
正确
Incorrect
不正确
Air
outlet
protective
cover
送风口防护罩
(to be provided
(安装现场提供)
on installation
site)
Monsoon
季节风
Monsoon
季节风
Air outlet protective
cover (to回风口防护罩
be provided
(安装现场提供)
on installation
site)
The底座高度要考虑到积雪
base height shall
consider the snow.
129
DIGITAL MULTI VRF
INSTALLATION
4 INSTALLATION OF INDOOR UNIT
4.1 Duct Type
4.1.1 Selection of installation site
● The selection of the installation place of the air conditioner unit
The installation must accord with the national and local safe criterion.
Since the quality of installation would affect the operation directly, user should contact the seller
and have the conditioner installed and tested by the professional install personnel according to the
install instruction instead of install by himself/herself.
Only connect the power after all the installation works are finished.
● The selection of the installation place of the indoor unit
☆ Prevent direct sun burn.
☆ Make sure that the top steeve, ceiling, and the structure of the construction etc. is strong enough to bear
the weight of the unit.
☆ The drainage pipe is easy to drain.
☆ The air flow is not blocked at the outlet and intake vents.
☆ The connecting pipe indoor and outdoor can by lead to outside conveniently.
☆ The unit cannot be installed in the place where stored the flammability, easy exploded thing or the place
where would have leakage of flammability and exploded gas.
☆ The unit cannot be installed in the place where has the corrupt gas and serious dust, saline fog,
lampblack and huge humidity.
Note!
The air conditioner unit installed in the following place may have malfunction, if the malfunction
cannot prevent, please contact the Nominated Repair Center Of Gree Electric Appliances, Inc. Of
Zhuhai.
①the place with greasy all around; ②the seashore place with salinity and alkali; ③the place with
vulcanized gas( such as vulcanized hot spring); ④the place with high frequency equipment ( such as
wireless equipment, electric welding machine and medical treatment equipment);⑤the place with special
environment.
130
DIGITAL MULTI VRF
INSTALLATION
1、The following figure is applicable to the indoor units of
GMV(L)-R22P/Na-K, GMV(L)-R25P/Na-K, GMV(L)-R28P/Na-K, GMV(L)-R32P/Na-K
GMV(L)-R36P/Na-K
Electric box
Nameplate
Liquid pipe
Gas pipe
Rear air
return vent
Lower air return
Drainage pipe
2、The following figure is applicable to the indoor units of GMV(L)-R45P/Na-K, GMV(L)-R50P/Na-K,
GMV(L)-R56P/Na-K, GMV(L)-R63P/Na-K, GMV(L)-R71P/Na-K, GMV(L)-R80P/Na-K,
GMV(L)-R90P/Na-K, GMV(L)-R112P/Na-K, GMV(L)-R125P/Na-K, GMV(L)-R140P/Na-K
131
DIGITAL MULTI VRF
INSTALLATION
Model
GMV(L)-R45P/ Na-K
GMV(L)-R50P/ Na-K
GMV(L)-R56P/ Na-K
GMV(L)-R63P/ Na-K
GMV(L)-R71P/ Na-K
GMV(L)-R80P/ Na-K
GMV(L)-R90P/ Na-K
GMV(L)-R112P/ Na-K
GMV(L)-R125P/ Na-K
GMV(L)-R140P/ Na-K
A(mm)
932
932
1112
1112
1112
1112
1382
1382
1382
1382
B(mm)
430
430
420
420
420
420
420
420
420
420
C(mm)
738
738
918
918
918
918
1155
1155
1155
1155
D(mm)
904
904
1070
1070
1070
1070
1340
1340
1340
1340
E(mm)
980
980
1155
1155
1155
1155
1425
1425
1425
1425
F(mm)
736
736
756
756
756
756
756
756
756
756
G(mm)
738
738
1008
1008
1008
1008
1278
1278
1278
1278
Model
H(mm)
I(mm)
J(mm)
Liquid pipe(inch)
Gas pipe(inch)
GMV(L)-R45P/ Na-K
125
207
266
Φ1/4"
Φ1/2"
Drainage pipe
(Outer ×Inner)
Φ30×Φ27
GMV(L)-R50P/ Na-K
125
207
266
Φ1/4"
Φ1/2"
Φ30×Φ27
GMV(L)-R56P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R63P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R71P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R80P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R90P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R112P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R125P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
GMV(L)-R140P/ Na-K
207
250
300
Φ3/8"
Φ5/8"
Φ30×Φ27
3、The following figure is applicable to the indoor units of
GMV(L)-R22P/NaB-K 、 GMV(L)-R22PS/NaB-K 、 GMV(L)-R28P/NaB-K 、 GMV(L)-R28PS/NaB-K 、
GMV(L)-R36P/NaB-K、GMV(L)-R36PS/NaB-K。
132
DIGITAL MULTI VRF
INSTALLATION
项 目
A
B
C
D
E
F
G
H
I
J
型 号
GMV(L)-R22P/NaB
GMV(L)-R22PS/NaB
GMV(L)-R28P/NaB
838
561
667
125
635 790
880
205 250 738
GMV(L)-R28PS/NaB
GMV(L)-R36P/NaB
GMV(L)-R36PS/NaB
4、The following figure is applicable to the indoor units of
GMV(L)-R45P/NaB-K、GMV(L)-R45PS/NaB-K、 GMV(L)-R56P/NaB-K、GMV(L)-R56PS/NaB-K、
GMV(L)-R71P/NaB-K、GMV(L)-R71PS/NaB-K、GMV(L)-R90P/NaB-K、GMV(L)-R90PS/NaB-K、
GMV(L)-R112P/NaB-K、GMV(L)-R112PS/NaB-K、GMV(L)-R140P/NaB-K、GMV(L)
-R140PS/NaB-K。
项目
型号
GMV(L)-R45P/NaB-K
GMV(L)-R45PS/NaB-K
GMV(L)-R56P/NaB-K
GMV(L)-R56PS/NaB-K
GMV(L)-R71P/NaB-K
GMV(L)-R71PS/NaB-K
GMV(L)–R90P/NaB-K
GMV(L)–R90PS/NaB-K
GMV(L)–R112P/NaB-K
GMV(L)–R112PS/NaB-K
GMV(L)–R140P/NaB-K
GMV(L)–R140PS/NaB-K
A
B
C
D
E
F
G
H
I
J
932
430
738
892
980
736
738
125
203
266
1114
420
918
1074
1112
736
918
207
207
300
1382
420
1155
1340
1425
756
1278
207
250
300
1382
420
1155
1340
1463
756
1278
207
250
300
133
DIGITAL MULTI VRF
INSTALLATION
5、The following figure is applicable to the indoor units of GMV-R224P/ Na-M、 GMV-R280P/ Na-M。
c
e
b
Air Outlet
f
d
a
Model
a
b
c
d
e
f
GMV-R224P/ Na-M
GMV-R280P/ Na-M
1560
910
1194
1194
292
342
134
DIGITAL MULTI VRF
INSTALLATION
4.1.3 Installation space requirements
Nut with
washer
Nut spring
pad
4.1.4 Installation demonstration
① Selection of style of return air
4
5
Wind supply
Supply air
2
1
Back
wind
Return
air
Install the back wind pipe (a)
Install return air duct (a)
5
3
Wind supply
Supply air
4
6
Return
air
Back
wind
1
Install the back wind pipe(b)
Install return air duct (b)
No.
Name
No.
Name
1
Return air inlet (with filter)
4
Indoor unit
2
Canvas air duct
5
Supply air duct
3
Return air duct
6
Test grill
② Installation of fresh air duct
1. When fresh air duct is need to be connected, cut the fresh air baffle as shown in fig.8. Plug up the gap of
fresh air baffle by sponge if fresh air duct is not used.
2. Install the circle flange so that the fresh air duct can be connected as fig.9.
3. Well sealed and heat preservation should be done for both air duct and round air duct.
4. Fresh air should be the air after filtrate treatment.
Cut off
Cut off
New wind
baffle air
Fresh
baffle
Circle wind pipe
135
DIGITAL MULTI VRF
INSTALLATION
③ Installation of air supply duct
Ceiling hoisting
Back wind
Wind supply
Supply
air
Return
air
Back wind
No.
1
2
3
4
5
6
Name
Hoisting
Return air
duct
Ducted type
indoor unit
Return air
inlet
Supply air bent
Air outlet
Note:Fig.6 only shows the install of rear return air inlet, button return air inlet can also been installed
according to the actual installation need. The method of installation is similar to the rear return air inlet’s.
The supply air duct, which is rectangle or circle and connect with the air inlet of the indoor unit, should at
least keep one open. The circle air duct type should adopt circle preservation pipe to transmit cool (heat) air
to room. The circle air duct should add a transitionary pipe, which size should match the size of air supply
duct of the unit. After connecting the transitionary pipe, install the circle air outlet vent connection pipe,
whose longest length to every individual air outlet vent should not over 10m. Ducted type indoor unit
model 70 can share 3 trainsitional pipe, while model 100,120 can share 4. The transitional pipe, whose
straight length is 200, and circle air outlet connection pipe, whose diameter is 200, produced by our
company, can be ordered separately as standard fittings. Model 50 and the model below it do not share
circle air duct. The following is the diagram for install circle air duct.
Note: 1, The longest length of air duct means the general length of the wing supply pipe to the farthest
air supply vent plus the general length of return air duct to the relative farthest return air vent.
2, To the unit with auxiliary heater, if the circle air duct is need to connected, the straight
length of transitional air duct should not shorter than 200mm.
7
1
2
3
4
5
6
Number
1
2
3
4
5
6
7
Name
Screw
Return air
duct
Ducted type
indoor unit
Return air
inlet
Transitional air
duct
Supply air duct
Air outlet
④ Setting hole for maintenance
After installation of hidden duct-type unit, manhole must be provided in ceiling on the electric box side of
the indoor unit. In respect to the manhole, the following points must be taken into consideration:
‹ For access, the manhole size shall be larger than 500mm×500mm.
‹ The manhole must be at a possible easily accessible for repair of electric elements and pipe.
‹ The air inlet may also be used as manhole for repair of motor.
4.2 Cassette-type Unit
4.2.1 Selection of installation site
136
DIGITAL MULTI VRF
1.
INSTALLATION
Obstruct should put away from the intake or outlet vent of the indoor unit so that the airflow can be
blown though all the room.
2.
Make sure that the installation had accord with the requirement of the schematic diagram of
installation spaces.
3.
Select the place where can stand 4 times of the weight of the indoor unit and would not increase the
operating noise and oscillate.
4.
The horizontally of the installation place should be guaranteed.
5.
Select the place where easy drain condensated coagulated water, and easy connect with outdoor unit.
6.
Make sure that there are enough space for care and maintenance. Make sure that the weight between
the indoor unit and ground is above 1800mm.
7.
When installing the steeve bolt, check if the install place can stand the weight 4 times of the unit’s. If
not, reinforce before installation. (Refer to the install cardboard and find where should be reinforced)
Note!
There will be lots of lampblack and dust stick on the acentric, heat exchanger and water pump in dining
room and kitchen, which would reduce the capacity of heat exchanger, lead water leakage and abnormal
operation of the water pump. The following treatment should be taken under this circumstance:
1.
Ensure that the smoke trap above cooker has enough capacity to obviate lampblack to prevent the
indraft of the lampblack by the air conditioner.
2.
Keep the air conditioner far from the kitchen so that the lampblack would not be indraft by the air
conditioner.
● Important notice:
‹
To guarantee the good performance, the unit must be installed by professional personnel according
with this instruction.
‹
Please contact the local Gree special nominated repair department before installation. Any malfunction
caused by the unit that is installed by the department that is not special nominated by Gree would not
deal with on time by the inconvenience of the business contact.
137
DIGITAL MULTI VRF
INSTALLATION
4.2.2 Dimensions Data
780(Gaps between hoisting screw rods)
840( Indoor unit)
890*(Ceiling opening)
950(Decorated surface boards)
GMV(L)-R140T/Na-K, GMV(L)-R125T/Na-K, GMV(L)-R112T/Na-K, GMV(L)-R90T/Na-K,GMV(L)-R71T/Na-K,
GMV(L)-R56T/ Na-K , GMV(L)-R50T/Na-K, GMV(L)-R45T/Na-K ,GMV(L)-R36T/Na-K, GMV(L)-R28T/ Na-K
Refrigerant pipe
Hoisting screw(X4)
680(Gaps between hoisting screw rods)
840( Indoor unit)
890(Ceiling opening)
950(Decorated surface boards)
A
Package Dimension
Width (mm)
Depth (mm)
Height (mm)
GMV(L)-R28T/Na-K
950
950
210
GMV(L)-R36T/Na-K
950
950
210
GMV(L)-R45T/Na-K
950
950
210
GMV(L)-R50T/Na-K
950
950
210
GMV(L)-R56T/Na-K
950
950
310
GMV(L)-R71T/Na-K
950
950
310
GMV(L)-R90T/Na-K
950
950
340
GMV(L)-R112T/Na-K
950
950
340
GMV(L)-R125T/Na-K
950
950
340
GMV(L)-R140T/Na-K
950
950
340
Model
138
DIGITAL MULTI VRF
INSTALLATION
4.2.3 Installation space requirements
H
>20
Wall
surface
Wall
surface
Wall
surface
≥1500
Model
GMV(L)-R28T/Na-K
GMV(L)-R36T/Na-K
GMV(L)-R45T/Na-K
GMV(L)-R50T/Na-K
≥1800
≥1500
GMV(L)-R56T/Na-K
GMV(L)-R71T/Na-K
unit:mm
GMV(L)-R90T/Na-K
GMV(L)-R 112T/Na-K
GMV(L)-R125T/Na-K
GMV(L)-R140T/Na-K
H
210
260
340
Ground
surface
H
>20
Wall
surface
Wall
surface
Wall
surface
≥1500
Model
GMV(L)-R22T/NaA-K
GMV(L)-R28T/NaA-K
GMV(L)-R36T/NaA-K
GMV(L)-R45T/NaA-K
≥1800
≥1500
H
250
unit:mm
Ground
surface
4.2.4 Installation demonstration
1 The primary step for install the indoor unit.
☆ When attach the hoisting stand on hoisting screw, do use nut and gasket individually at the upper and
lower of the hoisting stand to fix it. The use of gasket anchor board can prevent gasket break off.
2
Use install cardboard
☆ Please refer to the install cardboard about the dimension of ceiling opening.
☆ The central mark of the ceiling opening is marked on the install cardboard.
☆ Install the install cardboard on the unit by bolt (3 piece), and fix the angle of the drainage pipe at the
outlet vent by bolt.
139
DIGITAL MULTI VRF
INSTALLATION
3
Adjust the unit to the suitable install place. (Refer to the fig.2)
4
Check if the unit is horizontal.
☆ Inner drainage pump and bobber switch are included in the indoor unit, check if 4 angle of every unit are
horizontal by water lever. (If the unit is slant toward the opposite of the coagulate water flow, there may be
malfunction of the bobber switch and lead water drop.)
5
Backout the gasket anchor board used to prevent gasket break off and tighten the nut on it.
6
Backout the install cardboard.
Nut (supplied at scene)
Gasket (attachment)
Insert
Hoisting stand
Gasket anchor board
(attachment)
Tighten (double nuts)
[Fix the hoisting stand firmly]
[Fix the gasket firmly]
Bolt of one of the angle of outlet pipe is fix
on the angle of the drainage slot
Center of the ceiling
opening
Install cardboard
Water lever
Bolt (attachment)
Polyethylene pipe
Bolt (attachment)
[Fix the install cardboard]
Note!
●
Please do tighten the nuts and bolts to prevent air conditioner break off.
● Connect the refrigerant pipe
☆ When connect the pipe to the unit or backout it from the unit, please do use both spanner and torque
wrench. as shown in fig.3.
☆ When connect, smear both inside and outside of the flare nut with freeze motor oil, screw it by hand and
then tighten it with spanner.
☆ Refer to form 1 to check if the wrench had been tightened (too tight would mangle the nut and lead
leakage).
☆ Examine the connection pipe to see if it had gas leakage, then take the treatment of heat insulation, as
shown in the fig.3.
☆ Only use median sponge to entwine the wiring interface of the gas pipe and heat preservation sheath of
the gas collection tube.
140
DIGITAL MULTI VRF
INSTALLATION
Smear freeze motoroil
here
Median sponge (attachment)
(entwine the wiring interface
with seal mat)
Thread fasten(x4)
Torque wrench
Heat preservation
sheath of liquid inlet
tube (attachment) (for
liquid tube)
Spanner
Gas collection tube
Liquid inlet tube
Wiring interface
Heat preservation
sheath of gas collection
tube (attachment)(for
gas tube)
Fig.3
Flare nut
Form 1: The tightening torque needed for tightening nut
Diameter(Inch)
Surface thickness(mm)
Tightening torque (N.m)
Φ1/4’’
≥0.5
15-30 (N·m)
Φ3/8’’
≥0.71
30-40 (N·m)
Φ1/2’’
≥1
45-50 (N·m)
Φ5/8’’
≥1
60-65 (N·m)
Φ3/4’’
≥1
70-75 (N·m)
● Drainage hose
1. Install the drain hose
☆ The diameter of the drain hose should be equal or bigger than the connection pipe’s. ( The diameter of
polythene pipe: Outer diameter 25mm Surface thickness ≥1.5mm)
☆ Drain hose should be short and drooping gradient should at less 1/100 to prevent the formation of air
bubble.
☆ If drain hose cannot has enough drooping gradient, drain raising pipe should be added.
☆ To prevent bent of the drain hose, the distance between hoisting stand should is 1 to 1.5m.
1-1.5m
○(Correct) 1/100 or more gradient
× (wrong)
☆ Use the drain hose and clamp attached. Insert the drain hose to the drain vent, and then tighten the
clamp.
☆ Entwine the big sponge on the clamp of drain hose to insulate heat.
141
DIGITAL MULTI VRF
☆
INSTALLATION
Heat insulation should be done to indoor
Sponge(attachment)
drain hose.
Drain stepup pipe note
Clamp
Clamp(attachment)
☆ The install height of the drain raising pipe
should less than 280mm.
☆ The drain raising pipe should form a right
Drain hose
Sponge (gray)
angle with the unit, and distance to unit should
Below 4mm
not beyond 300mm.
Roof
Drain hose
Drain raising
hose
.
220mm
Ceiling
below500mm
Hoisting stand
below280mm
1-1.5m
.
Within 300mm
Clamp(attachment)
below500mm
D ra in h o s e (a tta c h m e n t)
.
☆ The slant gradient of the attached drain hose
should be within 75mm so that the drain hole
doesn’t has to endure the unnecessary outside force.
☆ Please install the drain hose according to the
following process if several drain hoses join
together.
below75mm
Instruction
T-tie in join drain hose
.
Above100mm
The specs of the selected join drain hose should fits the running capacity of the unit.
2
Check the smoothness of drain after installation.
☆ Check the drain state by immitting 600cc water slowly from the outlet vent or test hole.
☆ Check the drain in the state of refrigerating after installation of the electric circuit.
142
DIGITAL MULTI VRF
INSTALLATION
[Way of immiting]
Drain hose
Drain vent for repair use (plastic
stopper is included) (drain the water
in waterspout by this outlet vent)
.
Above100mm
Test hole cover
Test hole
< Immiting water from the rest hole>
Plastic water pot (The length of the
pipe should be about 100mm.)
<Immiting water from the outlet
vent terminal>
143
DIGITAL MULTI VRF
INSTALLATION
4.3 Floor Ceiling Type
4.3.1 Selection of installation site
Selection of Installation Location for Air Conditioner Unit
The installation of air conditioner unit must be in accordance with national and local safety codes.
Installation quality will directly affect the normal use of air conditioner unit. The user is prohibited
from installation by himself. Please contact your dealer after buying this machine. Professional
installation workers will provide installation and test services according to installation manual.
Do not connect to power until all installation work is completed.
● Selection of Installation Location
☆ Such a place where cool air can be distributed throughout the room.
☆ Such a place where is condensation water is easily drained out.
☆ Such a place that can handle the weight of indoor unit.
☆ Such a place, which has easy access for maintenance.
☆ Such a place where is permitting easy connection with the outdoor unit.
☆ Such a place where is 1m or more away from other electric appliances such as television, audio device,
etc.
☆ Avoid a location where there is heat source, high humidity or inflammable gas.
☆ Do not use the unit in the immediate surroundings of a laundry, a bath, a shower or a swimming pool.
☆ Be sure that the installation conforms to the installation dimension diagram.
● Caution for installation where air conditioner trouble is likely to occur
☆ Where there is too much of oil.
☆ Where it is acid base area.
☆ Where there is irregular electrical supply.
144
DIGITAL MULTI VRF
INSTALLATION
4.3.2 Dimensions Data
Model
Installation dimensions
Outline dimensions
E
D
A
B
C
GMVL-R28Zd/Na-K
GMV-R28Zd/Na-K
260
745
840
695
238
GMVL-R36Zd/Na-K
GMV-R36Zd/Na-K
260
745
840
695
238
GM(L-R50Zd/Na-K
GMV-R50Zd/Na-K
260
745
840
695
238
GMVL-R71Zd/Na-K
GMV-R71Zd/Na-K
260
1220
1300
600
188
GMVL-R90Zd/Na-K
GMV-R90Zd/Na-K
260
1500
1590
695
238
GMVL-R112Zd/Na-K
GMV-R112Zd/Na-K
260
1500
1590
695
238
1500
1590
695
238
GMVL-R125Zd/Na-K
GMV-R125Zd/Na-K
260
145
DIGITAL MULTI VRF
Model
INSTALLATION
Installation dimensions
Outline dimensions
C
D
A
H
B
GMV-R71Zd/NaB-K
1354
280
1420
700
245
GMV-R90Zd/NaB-K
1354
280
1420
700
245
GMV-R112Zd/NaB-K
1634
280
1700
700
245
GMV-R125Zd/NaB-K
1634
280
1700
700
245
146
DIGITAL MULTI VRF
INSTALLATION
4.3.3 Installation space requirements
☆ The space around the unit is adequate for ventilation (Refer to Fig.1)
Fig.1
4.3.4 Installation demonstration
● There are 2 styles of installation
☆ Ceiling type
☆ Floor type
Each type is similar to the other as follows:
1. Determine the mounting position on ceiling or wall by using paper pattern to indicate indoor frame. Mark
the pattern and pull out the paper pattern. (Refer to Fig.2)
2. Remove the return grill, the side panel and the hanger bracket from the indoor unit as per procedure bellow.
☆ Press the fixing knob of the air inlet grills, the grilles will be opened wider and then pull them out from
the indoor.
☆ Remove the side panel fixing screw and pull to the front direction (arrow direction) to remove. Side panel
fixing screw (Refer to Fig.3).
☆ Loosen two hanger bracket setting bolts (M8) on earth side for less than 10mm. Remove two hanger bracket
fixing bolts (M6) on the rear side. Detach the hanger bracker by pulling it backward (Refer to Fig.5).
Fig.2
Fig.3
3. Set the suspension bolt. (Use W3/8 or M10 size suspension bolts)
147
DIGITAL MULTI VRF
INSTALLATION
☆ Adjust the distance from the unit to the ceiling slab beforehand (Refer to Fig.4)
4. Fix the hanger bracket to the suspension bolt.
Warning!
☆ Make sure that extended suspension bolt from the ceiling stays inside the arrowed position. Readjust
the hanger bracket when it is outside the arrowed position. (Refer to Fig.6)
☆ Suspension bolt stays inside the cap of indoor unit. Never remove the cap.
5. Lift the unit and slide forward unit the dent. (Refer to Fig.7)
6. Screw tightly both hanger bracket-setting bolts (M8). (Refer to Fig.5)
7. Screw tightly both hanger bracket-fixing bolts (M6) to prevent the movement of the indoor unit. (Refer
to Fig.5)
8. Adjust the height so that rear side of the drainpipe slightly inclines to improve drainage.
Caution!
☆ Adjust the height by turning the nut with a spanner.
Insert the spanner from the hanger bracket opening. (Refer to Fig.8)
In case of hanging
It is possible to install using inward facing hanger brackets by not removing the brackets from the indoor
unit. (Refer to Fig.9)
Be sure to use only the specified accessories and parts for installation work.
148
DIGITAL MULTI VRF
INSTALLATION
B
4.4 Wall mounted type
4.4.1 Dimensions Data
C
A
Remark :The appearance will be different according to the models.
Model
GMV(L)-R22G/NaA-K
GMV(L)-R28G/NaA-K
GMV(L)-R36G/NaA-K
A(mm)
830
830
830
B(mm)
285
285
285
C(mm)
189
189
189
Model
GMV(L)-R22G/NaB-K
GMV(L)-R22G/NaC-K
GMV(L)-R28G/NaB-K
GMV(L)-R28G/NaC-K
GMV(L)-R36G/NaB-K
GMV(L)-R36G/NaC-K
GMV(L)-R45G/NaB-K
GMV(L)-R45G/NaC-K
A(mm)
770
770
830
830
B(mm)
250
250
285
285
C(mm)
190
190
189
189
Model
GMV(L)-R50G/NaB-K
GMV(L)-R56G/NaB-K
A(mm)
1020
1020
B(mm)
310
310
C(mm)
228
228
Model
GMV(L)-R50G/Na-K
GMV(L)-R56G/Na-K
GMV(L)-R71G/Na-K
GMV(L)-R80G/Na-K
A(mm)
907
907
1178
1178
B(mm)
290
290
326
326
C(mm)
195
195
227
227
Model
GMV(L)-R22G/NaG-K
GMV(L)-R28G/NaG-K
GMV(L)-R36G/NaG-K
GMV(L)-R45G/NaG-K
GMV(L)-R50G/NaG-K
GMV(L)-R356G/NaG-K
GMV(L)-R63G/NaG-K
GMV(L)-R71G/NaG-K
A(mm)
843
940
1008
B(mm)
275
298
319
C(mm)
180
200
221
149
DIGITAL MULTI VRF
INSTALLATION
>150
4.4.2 Installation space requirements
Schematic diagram of installation spaces
>150
>3000
>2000
>150
Important Notice:
‹
The unit must be installed by the professional personnel according to this installation instruction to
ensure the well use.
‹
Please contact the local Gree special nominated repair department before installation. Any malfunction
caused by the unit that is installed by the department that is not special nominated by Gree would not
deal with on time by the inconvenience of the business contact.
‹
It should be guide under the professional personnel when the air conditioner unit is moved to other
place.
150
DIGITAL MULTI VRF
INSTALLATION
4.4.3 Installation demonstration
Fig.1
1. Find the horizontal position by seton method; since the drainage pipe is on the left side, adjust the rear
panel to make its left side a little bit lower.
2. Fix the rear panel on the wall by bolt.
3. After installing the rear panel, pull it by hand to check if it is firm enough. The hang panel should support
the weight of an adult (60KG), and the weight shared by every bolt for steady should be fairly even.
4. The diameter showed on the fig.1 is 65mm.
Installation the Wall Mounted Type indoor unit
☆ Make the piping hole (Φ65mm) in the wall at a slight downward slant to the outdoor side. The center of
the hole should be determined refer to Fig.1
☆ Insert the piping-hole sleeve into the hole to prevent the connected piping and wiring from being
damaged when passing through the hole.
● Install the drainage pipe
☆ For well draining, the drain hose should be placed at a
Wrenched
downward slant.
Bent
☆ Do not wrench or bend the drain hose or flood its end
bywater. (Fig.2)
☆ Wrap heat resistant material when connect the longer
Flooded
drainage tube though indoor.
Fig .2
● Install the connection pipes
Connect the connect pipe with the two relative leading pipe, tie the nut on tie –in of the connect pipe tightly.
Note!
☆ Be careful in bending the connection pipes, or you will damage the pipes.
☆ If the tightening torque is too great in tightening the flare nut, leakage will happen.
151
DIGITAL MULTI VRF
INSTALLATION
Drainage equipment (inside type)
Discharge condensate water from
indoor unit when cooling
Drainage hose
Guide louver
(placed in air
outlet vent)
Air outlet vent
Air filter, purifier (in
air inlet grille)
Connecting pipe
Air inlet grille
Fig.8
152
DIGITAL MULTI VRF
INSTALLATION
4.5 1-way cassett type Unit
4.5.1Selection of installation site
1. Obstruct should be away from the air intake or outlet vent of the indoor unit so that the airflow
blow all over the place of the room.
2. Make sure the installation of the indoor unit accords with the requirement for installation
dimension drawing.
3. Select the place which can withstand 4 times weight of the indoor unit and would not increase
the operating noise and shake.
4. The installation place should be horizontal.
5. Select the place, where coagulated water is easy to discharge and outside unit to be connected.
6. Above 18000mm between the earth and indoor unit should be ensured for maintenance and
repair.
7. Use hoisting screw to check if the installation place can withstand 4 times weight of the units and
strengthen it before installing.
4.5.2 Dimensions Data
Important notice:
Drilling the hole of the ceiling and installing the units must be operated by professionals
4.5.3 Clearance data
153
DIGITAL MULTI VRF
INSTALLATION
4.5.4 Installation demonstration
Fig 3
Hoisting the main body of the unit
1. Hoisting the main body
Attach the hoisting stand base to hoisting screw. In order to firm the hoisting stand base, use
nuts with washers on either end of it.(refer to Fig. 1)
2. Please refer to the dimension of ceiling opening on the cardboard for installation
● There is a mark for ceiling opening center on the cardboard.
● There is also a mark for main body center on the cardboard.
● Use screws to fix the installation cardboard on the unit. (refer to Fig.3)
3. Adjust the unit to right installation place.
4. Check if the unit is horizontal.
Inner drainage pump and bobber switch are installed in indoor unit. Check if every side of the
unit is horizontal by water lever. (If the unit slants to opposite direction towards which coagulate
water flows, it will bring malfunction to the bobber switch and cause water drops. (refer to Fig.2)
5. Unscrew the screws on the cardboard, which can be used for installing front panel.
Drainage pipe
1. Installing drainage pipe
The diameter of drainage pipe should be larger than that of connecting pipe. (Polythene pipe:
dimension: outer diameter 25mm wall thickness≥1.5mm)
● Drainage pipe should be as short as possible and drooping gradient at least 1/100 to avoid the
formation of air bubble.
154
DIGITAL MULTI VRF
INSTALLATION
● If drainage hose cannot have enough drooping gradient, drainage raising pipe should be
installed.
● In order not to bend the drainage hose, the distance between hoisting stands should be 1 to
1.5m..
●
●
●
With accessory drainage hose and clamp, insert the drainage hose into the drainage faucet,
and then tighten the clamp.
Entwine the clamp of drainage hose with the big sponge to isolate heat.
Isolate heat for the outdoor drainage host.
Sponge (Gray)
Drainage Hose
Notice for drainage raising pipe
● The installation height should be less than 280mm.
● A right angle should be formed by the drainage raising pipe and unit, which should not be more
than 300mm far from the unit.
Ceiling
Note:
● The gradient of the accessory drainage hose should be within 75mm so that the drainage faucet
need not endure extra outside force.
● If several drainage hoses join together, please install them according to the following process.
155
DIGITAL MULTI VRF
INSTALLATION
The specs of the selected joint hose should fit the running capacity of the units.
●
Front panel body and installation
1.Take off the front panel from the panel body.
2. AS shown in Fig.4, install the panel body, and then tighten the screws according to the
sequences in the figures.
3 .As shown in Fig.5, install the panel on the panel ,and then turn it for fastening
156
DIGITAL MULTI VRF
INSTALLATION
5 INSTALLATION REQUIREMENTS OF REFRIGERANT PIPING
5.1 Specification
R410a refrigerant system
External
Diameter(mm/inch)
Thickness(mm)
External
Diameter(mm/inch)
Thickness(mm)
Φ6.35
≥0.8
Φ22.2
≥1.5
Φ9.52
≥0.8
Φ25.4
≥1.5
Φ12.7
≥1
Φ28.6
≥1.5
Φ15.9
≥1
Φ34.9
≥1.5
Φ19.05
≥1
5.2 Allowable Length and Height Differences of the Refrigerant Piping between the Indoor and Outdoor
Units
Capacity over 20KW
R410a refrigerant system
Total length (actual length) of fitting pipe
Length of the furthest fitting pipe
Allowable (m/ft)
value
500/1640
Actual length
500/1640
Equivalent length
175/574
Equivalent length of fitting pipe
from the 1st branch joint to farthest indoor unit
Fitting pipe
L1+L2+L3+L4+L5+L6+a+b+…+i+j
L1+L3+L4+L5+L6+j
40/131
L3+L4+L5+L6+ j
Height differences between
Outdoor unit at upper
50/164
-
indoor unit and outdoor unit
Outdoor unit at lower
40/131
-
15/49
-
Height differences between indoor units
157
DIGITAL MULTI VRF
INSTALLATION
Capacity lower than 20KW
Allowable (m/ft)
R410a refrigerant system
Total length (actual length) of fitting pipe
Length of the furthest fitting pipe
Fitting pipe
value
300/984
Actual length
100/328
Equivalent length
125/410
Equivalent length of fitting pipe
from the 1st branch joint to farthest indoor unit
Height differences between
Outdoor unit at upper
indoor unit and outdoor unit
Outdoor unit at lower
Height differences between indoor units
L1+L2+L3+a+b++c+d
L1+L2+L3+d
25/82
L2+L3+d
30/98
-
25/82
-
10/33
-
5.3 Selection of Y-Type Branch Pipe
R410a refrigerant system
Y-Type Branch Pipe
Total Capacity of the Downstream Indoor Unit (X)
Model
X≤300
FQ01Na
300<X≤600
FQ02Na
5.4 Selection of Diameter
① The diameter of the piping (the main pipe) from the Outdoor Unit to the first branch joint
R410a refrigerant system
Outdoor capacity code C
Gas pipe (mm/inch)
Liquid pipe(mm/inch)
50<C≤140
Φ15.9
Φ9.52
140<C≤180
Φ19.05
Φ9.52
180<C≤320
Φ22.2
Φ9.52
320<C≤400
Φ25.4
Φ12.7
400<C≤480
Φ28.6
Φ12.7
480<C≤600
Φ28.6
Φ15.9
Note: When the actual pipe length exceeds 90m, the pipe diameter shall be increased accordingly.
158
DIGITAL MULTI VRF
INSTALLATION
② The diameter of the piping between branch joints (the branch pipe)
R410a refrigerant system
Outdoor capacity code C
Gas pipe (mm/inch)
Liquid pipe(mm/inch)
C≤50
Φ12.7
Φ6.35
50<C≤140
Φ15.9
Φ9.52
140<C≤180
Φ19.05
Φ9.52
180<C≤320
Φ22.2
Φ9.52
320<C≤400
Φ25.4
Φ12.7
400<C≤480
Φ28.6
Φ12.7
480<C≤600
Φ28.6
Φ15.9
Note: When the actual pipe length exceeds 90m, the pipe diameter shall be increased accordingly.
③ The diameter of the piping from the branch joint (branch pipe) to the indoor unit
R410a refrigerant system
Outdoor capacity code C
Gas pipe (mm/inch)
Liquid pipe(mm/inch)
22, 28 Type
Φ9.52
Φ6.35
36, 45, 50 Type
Φ12.7
Φ6.35
56, 63, 71, 80, 90, 10, 112 Type
Φ15.9
Φ9.52
Note: When the actual pipe length exceeds 90m, the pipe diameter shall be increased accordingly.
5.5 Selection of Refrigerant Piping between Outdoor Unit and Outdoor Unit ( for module unit)
1) Selection of components between module and module
Notes
Sub-assembly corresponding to
outdoor module
Model
ML01
Name
ML01- Liquid pipe
ML01- Gas pipe
159
DIGITAL MULTI VRF
INSTALLATION
2) Selection of pipe diameter between module and module
a Pipe diameter between outdoor unit and connection component
R410a refrigerant system
Single module capacity code C
Gas pipe (mm/inch)
Liquid pipe(mm/inch)
C≤280
Φ22.2
Φ9.52
280<C≤400
Φ28.6
Φ12.7
b Pipe diameter between connection component of module and connection component of module
R410a refrigerant system
Sum of capacity code of upstream module C
Gas pipe (mm/inch)
Liquid pipe(mm/inch)
C≤280
Φ22.2
Φ9.52
280<C≤450
Φ28.6
Φ12.7
450<C≤670
Φ28.6
Φ15.9
670<C≤950
Φ34.9
Φ19.1
950<C≤1350
Φ41.3
Φ19.1
C>1350
Φ41.3
Φ22.2
c Piping used for balancing lubricant
The oil balance pipe is connected by using Φ9.52 copper pipe. For three outdoor units arranged in parallel,
one 3-way joint having an inner diameter of Φ9.7 shall be used in the oil balance pipe.
160
DIGITAL MULTI VRF
INSTALLATION
6 INSTALLATION OF REFRIGERANT PIPING
6.1 Flow Chart of Installation
6.2 Three Principles of Refrigerant Piping Installation
Keep to the three principles of refrigerant piping:
Key Factors
Dry
z
Measures to Avoid Failure
Invasion of outside water
Example:
Rainwater, engineering
water
Clean
z
Invasion of indoor condensate
z
Formation of oxides inside the
pipe during welding
z
Invasion of dust and foreign
articles from outside
Airtight
z
Incomplete welding
z
Leakage from flared port
z
Leakage from edge
161
DIGITAL MULTI VRF
INSTALLATION
6.3 Installation of Metal Embedded Pipe
‹
Work Order
Plot the line on ground if possible and use laser to project it onto the roof. This is quick and correct.
‹ Advance Installation of Metal Embedded Parts
Please select according to local codes
‹ Subsequent Installation of Expansion Bolts
In case that the metal embedded parts cannot be used due to design change, the expansion bolts may
be used.
‹ Subsequent Installation of Expansion Bolts
● The foot pedal shall be supported on three points if exceeding 2m.
The foot pedal must be fixed securely to the ladder.
● Please do not work on the top of ladder.
6.4 Installation of Carriage of Refrigerant Piping
1)Fixing of horizontal pipe
The refrigerant pipe will extend and shrink with each start or stop of the air conditioner unit (5~10
times / hour). Under a temperature difference of 80①, this extension may reach 13.84mm for every 10m.
To prevent failure, the pipes must be reinforced as follows.
Spacing between supports
Outer diameter of pipe (mm)
6.35-8.52
Over 12.7
Spacing between supports (m)
Below 1.2
Below 1.2
Note: If the gas pipe and liquid pipe are suspended together, the size of liquid pipe shall prevail.
CAUTION:
Never let the pipe in direct contact with the fixing metal parts. Thermal insulation shall be provided
around the fixing metal parts; otherwise, condensing will occur.
2)Fixing of vertical pipe
The vertical pipe may be fixed by using the commodity tools in market or self-made tools. As above, the
fixing point shall also be thermally insulated.
3)Fixing of other points
Measures shall be taken to prevent the extension or shrinkage of pipes from causing excessive loads to
some positions, machine joint and waterproof points. Generally, such positions refer to the branch pipe
joint, pipe ends, four sides of indoor unit and wall-cross hole.
6.5 Management and Machining of Refrigerant Piping
1)Storage
‹ After receiving the refrigerant pipe and other components, do not move them to the storage until
confirming that they have no deformation, bend, crack or damage.
‹ The pipe end must be sealed to prevent the invasion of moisture or wastes.
‹ The copper pipe with coating may become deformed under the compression of the coating material,
so that the coils shall be placed upright.
‹ To avoid the invasion of moisture or wastes, a support higher than the ground must be built by
162
DIGITAL MULTI VRF
INSTALLATION
using woods.
‹ Care of pipe end during construction
The pipe ends must be well cared during construction. According to the working position, work progress
and surrounding environment, the most effective way is to seal the end and wrap with adhesive tape.
i.
Sealing method
Clamp the pipe end and weld on it.
Clamp the pipe end to flat and weld on the clearance. Then, charge nitrogen 2~5kgf/cm2. This
will be more effective.
ii.
Method for wrapping with adhesive tape
Seal the pipe end with ethylene tape.
2)Coil unwinding
CAUTION:
‹
When unwinding the coil, take care not to drag it on the ground. The coil shall be slowly
unwound on ground without any twisting. In case of excessive compression by any hard object
during unwinding, the thermal insulation materials may be damaged and cannot be recovered,
which will deteriorate the performance of thermal insulation. Do not unwind carelessly.
Otherwise, the fitting pipe might be flattened.
‹ The copper pipe shall be rounded if the pipe end is deformed.
(The higher the size, the higher the possible deformation)
3)Measuring of pipe
‹
(To reduce the resistance and length of copper pipe), the dimension of main refrigerant pipe shall be
so taken that the bends shall be minimized, the radius of bend section shall be increased and the
upstream and downstream section shall be reduced. Use the method that can reduce the actual length
and equivalent length of the copper pipe.
‹ Sometimes the connection pipe of indoor unit must be adjusted due to the relation with accessories,
drainage pipe and connection surface. Therefore, a fairly marginal dimension shall be taken.
4)Cut·Chamfer
‹ Cut
a) Cut vertically to axis direction by using special pipe cutter that is suitable to the dimension of
copper pipe (big, medium, small).
163
DIGITAL MULTI VRF
INSTALLATION
b)
During operation, press and rotate the pipe cutter slowly and cut off the copper pipe without
causing any deformation.
Never use saw or grinding wheel, because the copper scraps may be left inside the pipe. Even use of such
tools once will make all works scrapped. It is useless no matter how good the quality of other works. It is
best that all operators shall have one pipe cutter and at least one pipe cutter of big dimension shall be
provided on site.
CAUTION:
To prevent the invasion of water or waste, avoid placing the copper pipe directly on ground.
‹ Chamfer
Burrs may occur on the cutting face of copper pipe and must be removed. Meanwhile, purge the foreign
articles out of the pipe and refinish the pipe end.]
● Use scraper or other tools to remove the burrs on inner side.
(To prevent copper scraps from falling into the pipe, please keep the pipe end downward during operation).
● If the pipe end is obviously deformed, please cut and throw it off, and then refinish the pipe end.
● Eliminate the copper scraps thoroughly, and use cotton yarn to wipe the pipe clean.
※ The flared joint must be kept smooth.
※ When removing the burrs with scraper, do not remove too much, especially for the fitting pipe of small
diameter; otherwise the contact surface of the flared joint will be reduced. Do not cause any scores, and
avoid cracking after the flared joint is formed.
※ Adverse impact if the burrs are removed too much with scraper:
Too much eliminated
The contact face
becomes small
Flared nut
5)Pipe bending
◆ Work Methods:
a) Bend by hand ………………………..Suitable to fine copper pipe (Φ6.35mm-Φ12.7mm).
b) Machining with spring pipe bender …….. Bend by inserting the spring into copper pipe or
sheathing onto the copper pipe (Φ6.35mm-Φ22.2mm).
c) Machining with hand-operated pipe bender……Use the pipe bender of suitable dimension
(Φ6.35mm-Φ22.2mm).
d) Machining with electric pipe bender (hydraulic)……Suitable for mass machining of fine and
coarse fitting pipes (Φ6.35mm-Φ69.9mm).
Advantages
164
DIGITAL MULTI VRF
INSTALLATION
Decrease the weld joint, thus reduce the possibility of leakage and oxidization.
For example:
It can decrease the weld by 8 spots. Please act now to improve the quality.
※ No joint is required, which will save the material costs. Reduced waste of fitting pipe materials.
※ Reduced resistance in the fitting pipe. The bending radius higher than the pipe joint.
◆CAUTIONS
※ During bending, there shall be no wrinkling or deformation on the inner side of the copper pipe.
※Spring pipe bend
※ The bender inserted into the copper pipe must be cleaned.
※ Do not bend over 90º. (Otherwise, wrinkling may be formed on the inner side of copper pipe and in the
future, the copper pipe will be broken from this position.)
Steel pipe
Jacketed bender
Inner side wrinkled
and deformed
Bent, with fissure
occurring on this side
Section
The copper pipe might be
deformed even if it is not bent
Correct section
Bend section
6)Flaring
The flaring refers to expansion of pipe opening. The copper pipe is inserted here to replace the casing pipe.
In this way, it is only needed to weld on one position where the pipe is expanded.
Welding
6.6 Installation of Refrigerant Piping
1)Precautions on piping works
‹ At the site of transport, storage and construction, the two ends of copper pipes shall be
165
DIGITAL MULTI VRF
INSTALLATION
sealed with plastic sealing caps. Before welding, copper pipes must be cleaned (washing the
inner side of pipe with alcohol) to ensure no dust and no water in pipeline.
‹ Nitrogen-filled welding shall be used for the welding of copper pipes. Nitrogen pressure
shall be 0.05~0.3MPa. Nitrogen flow can be sensed by hand.
‹ When multiple multi-connected units are installed, refrigerant piping must be marked to
avoid confusion between pipes of different units.
‹ A two-way drier shall be mounted at the liquid pipe side at the place where an outdoor unit is
connected.
2)Assemble copper pipes
The copper pipe shall be vertically inserted to the specified length. The centerline of two assemblies shall
overlap. The position shall be determined for welding. To ensure correct mounting size, do not determine
the position with your hands, thus to prevent the copper pipe from moving when heated.
See below for the welding size of copper pipe:
Outer diameter of pipe D
ф6.35
6
ф9.52, ф12.7
7
ф15.8
8
ф19.05, ф22.2, ф25.4
10
ф28.6, ф31.8
12
≥ф35
14
D
A
(mm)
Min. insert depth B (mm)
Clearance
A-D
0.05~0.21
0.05~0.27
0.05~0.35
If the mounting clearance is too large, the diameter of coarse pipe may be reduced to an appropriate value
to according to applicable specifications.
3)Installation of branch pipe
The branch pipe plays the function to divert the refrigerant flow. Therefore, the selection and installation of
branch pipe is very important to the operation of multi-unit. Based on correct selection of branch pipe, the
branch pipe must be installed according to installation specifications.
‹ Connection schematics for Y-type branch pipe
The connection of Y-type branch pipe is as shown below. The inlet is connected to outdoor unit or previous
branch; the outlet is connected to indoor unit or next branch.
To other manifold
pipe or indoor unit
Outlet 1
Site pipe
Inlet
Outlet 2
Outdoor unit
Site pipe
Y-type Manifold Pipe
‹ Installation specifications for branch pipe
Placement of branch pipe
The branch pipe can only placed horizontally. Meanwhile, two branch pipes must be on the same plane.
The spacing between two branch pipes must be over 800mm, the spacing between two bends must be over
800mm, and the spacing between branch pipe and bend point must also be over 800mm.
166
DIGITAL MULTI VRF
INSTALLATION
Within 30°
Within 30°
A-A Schematics
B-B Schematics
Connection of branch pipe
The Y-type branch pipe is installed with additional tube. The purpose is to adjust the different pipe
diameters. If the pipe size selected on site is different from the size of branch connector, please use the pipe
cutter to cut from the middle of different connection pipes and remove the burrs. Then, insert the copper
pipe to appropriate depth. The branch pipes from Gree are all provided with positioning mark.
Copper pipe
Branch pipe
Cut from the middle of copper
pipe as needed
The connection method that copper pipe is in couple with a smaller branch pipe shall not be used.
167
DIGITAL MULTI VRF
INSTALLATION
Copper pipe
Branch pipe
Correct connection
Wrong connection
Copper pipe shall not be inserted too much for connection with branch pipe.
Copper pipe
Branch pipe
Correct connection
Wrong connection
168
DIGITAL MULTI VRF
INSTALLATION
6.7 Welding of Copper Pipe
1)Braze welding
Materials for braze welding
There are two kinds of braze welding, soft braze welding and hard braze welding. Hard braze welding is
required in this case.
Selection of braze welding
Red copper + red copper:brazing filler metal is Bcu93P(GB 6418),and welding flux is not needed. Flame
flux: capable of preventing the surface of copper pipes from oxidation, recommended for use.
Temperature for braze welding:820-860① (copper pipe becomes light red)
2)Safety acknowledgement before operation
a. Safety acknowledgement before operation
b. Acknowledgement on work suits(helmets, clothes, safety bags and safety shoes)
c. Description of work location and environment
d. Job division shall be made. Job content, method and order shall be indicated. Risk prediction activities
shall be performed.
e. “Construction Schedule” shall be worked out.
f. Head of each group shall be assigned.
g. Risks of occurrence of an accident such as electric shock or fire shall be indicated.
h. Instructions on how to use electric machinery properly shall be available.
i. Locations marked with “Staff Only” shall be indicated.
j. An application is necessary for use of open flame and shall be reviewed by on-site safety officer for
approval.
k.Instructions given by fire authorities shall be accepted in accordance with local laws and regulations.
l. Tools shall be sorted and counted. Upon knocking off for the day, tools shall be sorted and counted. If
necessary, the piping system shall be charged with coolant to avoid exhaustion.
a. Construction personnel must have relevant operation qualification.
Flame operation must be undertaken by qualified persons in accordance with local laws and
regulations.
b. Wear coveralls (cotton for the best), safety shoes, safety helmet, leather gloves, protective goggles
and anti-dust mask.
Welding torch with back fire arrestor shall be used to ensure safety.
c. Take care not to be burned by flame and heating parts.
d. Gas cylinder shall be handled carefully to prevent leakage.
e. Combustible substances in the surrounding areas shall be moved away. If movement is impossible,
fire proofing treatment shall be taken properly, such as being covered by flame-proof enclosure.
f. Good ventilation is necessary to avoid breathe in of harmful gas.
g. Appropriate measures shall be taken if there is a safety problem.
h. Operation on connectors of branch pipes as well as on the surrounding of pipe ends shall be
performed on the ground as possible, because heating is difficult to control at a high place and
welded part of a branch pipe is prone to be melted to cause leakage.
For example:
Weld the pipe approx. 1m before and
behind the reflared position, and wrap
with thernal insulation materials. Then,
weld on higher position.
Approx. 1m
Approx. 1m
169
DIGITAL MULTI VRF
INSTALLATION
i. To avoid the position difficult to weld, you may add a prefabricated assembly below.
Drainage pipe
Difficult to weld at
this position
4)Operation order
Basic procedures for welding:
Assemble copper
pipes
Cleaning
Check whether clearance
is proper.
Fill nitrogen N2
Nitrogen pressure 0.05-0.3Mpa 0.5±0.1kgf/cm2
Welding flux
Welding heating
Acknowledge
welding flux
Add welding flux
Cooling, continue to fill nitrogen
for over 10s
Shut off nitrogen
Make visual inspection to
the weld quality
a. Cleaning of portions for braze welding
Polishing……………………Removing metal materials at connection portion. (Removing oxidation
film using non-woven fabric, abrasive cloth or abrasive paper)
Ungrease……………………If any oil stain is existent, acetone or spirit solvent shall be used for
ungrease treatment.
At the same time, compressed air at 0.8MPa (gauge pressure) shall be used for cleaning. The cleaning
shall be repeated not less than 3 times, until there is no dirt discharged.
b. Check whether clearance between pipe and connector is proper.
Put the connector into the pipe and face downward. If the connector does not fall down depending on
friction force, the clearance is considered proper.
c. Nitrogen-filled protection
● Since vigorous oxidation would occur on the surface of copper pipe at braze welding temperature,
170
DIGITAL MULTI VRF
INSTALLATION
to effectively restrain the generation of oxide coating in copper pipe, nitrogen-filled protection for
copper pipe is necessary.
● After copper pipes are assembled, nitrogen shall be filled in copper pipe connectors.
● Nitrogen charging method:
Pressure is 0.05~0.3MPa. Nitrogen flow of 4~6L/min (gas flow can be sensed by hand) shall be
guaranteed to charge in work pieces.
After assembling, nitrogen begins to charge until welding is finished and will continue over 10s
during cooling after welding.
※ Main points of nitrogen charge(See the drawing below)
◆ When nitrogen is charged, the press switch on the quick connector and inflator shall be closed to let
nitrogen totally filled in the pipe.
◆ Make sure nitrogen reaches all welding connectors in order to effectively discharge air.
◆ A vent port must be available when nitrogen charge is continuously performed, or otherwise gas
would escape from gap around connector, making welding stuffing difficult and prone to pores.
充氮管
Nitrogen charge
pipe
Copper
pipe
铜管
氮气(N2) N2
Nitrogen
Places requiring protection
焊接需保护处
during
welding
铜管
Copper
pipe
出气口
Vent
port
d. Welding heating
Notes:
● Braze welding is flame hard braze welding. Relevant safety operating regulations must be abided by.
● Confirm that nitrogen is flowing through before copper pipe is heated.
● Neutral flame or slightly reducing flame shall be used for red copper braze welding. Outer flame is
normally used. Copper pipe connectors shall be heated uniformly. Take care to distribute heat in
terms of dimension of pipe material. Generally, insert pipe shall be preheated at first for close
matching and then swayed along length of connector to make it heated uniformly until braze welding
temperature is approached; then copper pipe is heated circularly to reach braze welding temperature
(copper pipe becomes light red) and at the same time brazing filler metal is added circularly to fill in
the clearance around the connector uniformly; and afterwards, the welding torch is slowly moved
away from the pipe and a small amount of brazing filler metal continues to be filled in until smooth
fillet is formed.
● During heating, welding rod shall not be burned directly by flame. Heating time shall not be very
long.
● During welding, flame shall be controlled well on its direction and kept away from rubber casing,
sponge and cables.
e. Post-welding treatment(cooling)
● After welding, in the condition of nitrogen protection available, the connector shall be heated until
the copper pipe changes color (200-300①), i.e. annealing treatment.
● Before welding seam becomes completely solidified, welded pieces shall not be moved or shocked.
● For welded piece cooled by water, take care not to let water enter into copper pipe and try to prevent
residue water flowing into the pipe when welded piece is laid aside.
f. Quality and inspection of braze welding
Welding seam should have smooth surface. Fillet should be even and full with natural arc transition. Braze
171
DIGITAL MULTI VRF
INSTALLATION
welding connector should be free from defects such as over-burning, welding blockage, crack, rough
surface of welding seam and burning through. Welding seam should be free from defects such as pore, slag
inclusion, underfill, rosin joint and overlap.
Weld spot
172
DIGITAL MULTI VRF
INSTALLATION
5)Others
◆ When braze welding is to be performed underneath, a simple support shall be built, such as two ladders.
◆Braze welding shall be easy to operate downward or in transverse direction. In upward operation,
brazing filler metal is prone to fall so that high skills are required.
Solder
Solder
Weld torch
Weld torch
Transverse
Solder
Weld torch
Upward
Downward
◆Cooling
To avoid getting a burn in following processes, common wet cloth (humidity content is low, meaning that
there shall not be water drips when welded part is cooled; and because shrinkage factor of copper is
different from that of welding material, too quick cooling that would cause cracking of braze welding shall
173
DIGITAL MULTI VRF
INSTALLATION
be avoided) can be used for cooling welded parts.
◆The following items shall be checked after welding is completed
● Is there any pore or hole on welded part?
● Is there evident “sagging of brazing filler metal”?
6.8 Cleaning of Refrigerant Piping
After a section of pipeline is welded, cleaning of piping is necessary.
Nitrogen pressure is utilized to remove foreign matters (such as dust, water and beryllium oxide caused by
welding) in the piping.
1)Main purposes of cleaning are as follows:
‹ To eliminate oxide caused by insufficiency of nitrogen-filled protection during pipe welding.
‹ To remove foreign substances and water that may enter the piping due to improper storage and
transport.
‹ To check whether big leakage is existent at connections of the piping between indoor unit and
outdoor unit
2)Cleaning steps:
a. Mount a pressure gauge on nitrogen cylinder;
b. High pressure end of the pressure gauge is connected to the refrigerant filling nozzle of the small pipe
(liquid pipe)
c. All copper pipe ports outside the A side of indoor unit shall be blocked by blanking plugs.
d. The valve on nitrogen cylinder shall be opened to maintain pressure at 28Kgf/ cm2
e. Check whether nitrogen flows through the liquid pipe of indoor unit A
f. Cleaning
The mouth of the pipe shall be blocked with insulation material held by hand until pressure rises to a level
difficult to be withstood, and at the moment the insulation material shall be released quickly. And then the
mouth shall be blocked again. Repeat such procedures several times. Afterwards, use a wood board posted
with white paper to check it. If there is not evident dirt on the white paper, the pipe will be considered
clean.
g. Shut off the main valve of nitrogen
h. Repeat the above procedures on indoor unit B
i. After cleaning of liquid pipe, gas pipe shall be cleaned in the same way.
174
DIGITAL MULTI VRF
INSTALLATION
6.9 Pressure Maintaining and Leak Hunting
1)Pressure maintaining of refrigerant piping
After refrigerant piping of a system is welded
‹ A refrigerant filling nozzle shall be welded respectively on the big pipe and on the small pipe on the
outdoor unit side.
‹ Pipes connected to the end of indoor unit and outdoor unit shall be clamped to be flat and welded to
be sealed.
Steps of pressure maintaining and leak hunting of refrigerant piping are as follows:
Operating Steps:
◆ Pressurization
Use nitrogen to add pressure from Freon nozzle of the gas and liquid pipe on outdoor unit side:
Step 1: Increase the pressure to 0.3MPa and wait for 3 minutes or longer
Step 2: Increase the pressure to 1.5MPa and wait for 3 minutes or longer
The step 1 and 2 are focused on checking the significant leakage point. If any, reweld immediately or
repair the leakage point.
Step 3: Increase the pressure to 2.5MPa and keep it for approx. 24 hours to check the small leakage.
Though the pressure is increased to 2.5MPa, it cannot be guaranteed to find out the small leakage if the
waiting time is too short. Therefore, the pressure in Step 3 must be kept for 24 hours.
Note: During pressure maintaining after nitrogen is filled, the pressure gauge shall not be dismantled,
because activities of dismantling or mounting pressure gauge would affect pressure change.
◆Check pressure drop
Criteria for Inspection eligibility:
※ Except for temperature influences (pressure changes about 0.01MPa for temperature change of 1①), if
pressure drop is not more than 0.02MPa within 24h, the system will be eligible. For example, nitrogen is
filled to reach 2.5MPa at 30①; after 24 hours, when temperature becomes 25①, the system will be eligible
if pressure is over 2.43 MPa and ineligible below 2.43 MPa.
※ If ineligible, leak sources must be located. After leak sources are found, re-welding or repair welding is
necessary. Then, the above procedures shall be repeated. Nitrogen is filled, pressurized and maintained
until pressure drop remains within required range.
◆Leak check
[Check 1] When pressure drop is found, leak hunting shall be performed in the ways as follows:
a. By ears…….to listen voices related to leakage
b. By hands……to sense whether leakage is existent at connecting parts
[Check 2] If no leakage is found using the above methods, nitrogen shall be discharged and refrigerant
shall be filled in to reach 0.5MPa.
a. By soap and water……soap bubbles will show leakage positions if any.
b. Detector (such as halide detector) can be used for leak hunting
Using the above methods, check all possible leak sources.
If leakage still fails to be located, sectional check shall be taken for refrigerant piping that would be
divided into multiple check portions for locating leak source in a certain section.
175
DIGITAL MULTI VRF
INSTALLATION
2)Pressure maintaining and leak hunting of the system(with refrigerant piping in connection with
indoor unit and outdoor unit)
When refrigerant piping is to be installed, pressure maintaining and leak hunting is required for the piping.
After refrigerant piping is in connection with indoor unit and outdoor unit, pressure maintaining and leak
hunting is also required. The purpose of the test is to check whether any leak is existent at threaded
connection of indoor unit and outdoor unit and at new welded points.
Steps:
◆Nitrogen is charged to reach 2.5MPa and remains at the pressure for 24h (nitrogen shall be filled from
refrigerant filling nozzles at the big valve as well as the small valve using a pressure gauge; during
pressure maintaining after nitrogen is charged, the pressure gauge shall not be dismantled.)
◆Observe whether pressure changes in 24 hours. (for eligibility criteria, see pressure maintaining and leak
hunting of refrigerant piping in 5.5.2)
◆If any leakage, please check threaded connections and new welded spots of indoor unit and outdoor unit.
Repair welding shall be performed immediately. Afterwards, pressure maintaining is repeated until
eligibility is reached.
6.10 Heat Preservation of Refrigerant Piping
1)Connection of thermal insulation pipe
Carry out thermal insulation to the refrigerant pipe after confirming that it has no leakage.
Please perform thermal insulation to the refrigerant pipe according to the steps below
◆Check if the thermal insulation pipe has met the thickness requirements. If not, the condensing water is
easy to attach on thermal insulation pipe and finally drips. The thickness requirements are shown below:
Refrigerant Pipe (mm) (Outer Dia. x Thickness)
Thickness of Thermal Insulation
Materials (mm)
Φ6.35×0.5
≥10
Φ9.52×0.71
≥10
Φ12.7×1
≥15
Φ15.9×1
≥15
Φ19.05×1
≥15
Φ22.2×1.5
≥20
Φ25.4×1.5
≥20
Φ28.6×1.5
≥20
Φ34.9×1.5
≥20
◆Wrap the refrigerant pipe according to required thickness. The clearance between thermal insulation
pipes shall be sealed with self-adhesive sticker.
◆Wrap the thermal insulation pipes with tapes, thus to extend their ageing time.
2)Thermal Insulation of Branch Pipe
Each branch pipe is provided with foam. Wrap the branch with the included foam. The upper and lower
foam shall be sealed with self-adhesive sticker. All the sections with or without foam shall be wrapped by
using thermal insulation pipe. The butt connection between foam and thermal insulation pipe shall be
sealed with self-adhesive sticker.
176
DIGITAL MULTI VRF
INSTALLATION
3)Cautions:
The thermal insulation materials shall be able to withstand the pipe temperature. For heat pump unit, it is
required to withstand a temperature not lower than 70① on liquid pipe side and not lower than 120① on
gas pipe side. For cooling-only unit, it is required to withstand a temperature not lower than 70① on both
liquid pipe side and gas pipe side. Example: Heat resistant PVC foam (over 120①); Foam PVC (over
100①)
‹ The connector between indoor unit and outdoor unit shall be wrapped with thermal insulation
materials, and shall have no clearance to the wall on which the outdoor unit is mounted, as shown
below.
‹
‹
When wrapping the thermal insulation tape, each circle shall suppress half of the previous circle.
To avoid reducing the thermal isolation effect, do not wrap the tapes too tight.
After completing the protection work and wrapping the pipes, use the sealing materials to block
the holes in the wall.
6.11 Vacuum Pumping
1)Purposes of vacuum pumping
‹ Discharge air and nitrogen in the piping to obtain vacuum state.
‹ Vacuum is dry, capable to remove moisture in the system.
Under atmospheric pressure, the boiling point of water is 100①. But with increased vacuum degree
created by vacuum pump, the boiling point rapidly reduces. If boiling point reduces below ambient
temperature, moisture in piping will be evaporated. If vacuum is 0Kgf/cm2of absolute pressure (gauge
pressure is -1Kgf/cm2), moisture in the system can be evaporated totally
2)Selection of vacuum pump
Proper vacuum pumps must be selected before vacuum pumping. Insufficient capacity of selected vacuum
pump would lead to overtime of vacuum pumping and fall short of the requirement for vacuum degree. A
proper vacuum pump can obtain vacuum degree of 0Kgf/cm2 (gauge pressure -1 Kgf/cm2) after vacuum
pumping
Features of a vacuum pump shall be determined by two factors as follows:
‹ Selection of a pump that can meet expected requirement (i.e. gauge pressure of -0.1MPa shall be
obtained)
177
DIGITAL MULTI VRF
INSTALLATION
‹ Exhaust flow is high (over 40L/min).
The following vacuum pumps are recommended.
Model
Lubricant shaft pump
Non-lubricant shaft
pump
Use
Maximum vacuum air
displacement
Air discharge
Vacuum drying
100L/min
Suitable
Suitable
50L/min
Suitable
Suitable
Comparison table of different pressure units is as follows:
Standard air
Unit
pressure
Relative pressure
kg/cm2
Absolute pressure
2
mm Hg
Vacuum degree
0
-1.033
kg/cm
1.033
0
mmHg
0
-755
3)Vacuum pumping
The steps are as follows:
a. Expel the nitrogen after leakage detection;
Connect the pressure gauge to Freon nozzle on outdoor liquid valve and gas valve, and connect a vacuum
pump. Then, establish vacuum simultaneously from high pressure side and low pressure side.
Pressure gauge connector valve
Connector on gas side
Vacuum pump
Connector on liquid side
Start the vacuum pump and turn on “LO” and “HI” knobs
b. Continue for 0.5~1.0 hour after the vacuum level reaches -0.1MPa (gauge pressure -1kgf/cm2). Then,
close the “VH” knob on high pressure end and “VL” knob on low pressure end to stop the vacuum pump.
c. Remove the hose connected to vacuum pump and reconnect it to the refrigerant tank. Expel the air in the
hose. Open the “VL” knob on low pressure end to charge refrigerant to the system piping. When the
pressure reaches 0.0kgf/ cm2, close the “VL” knob on low pressure end.
d. Remove the hose connected to refrigerant tank and reconnect it to vacuum pump. Start the vacuum
pump and open the “VH” knob on high pressure end. Pump for 30 minutes from high pressure end and
then open the “VL” knob to pump from low pressure end, until the vacuum level reaches -0.1MPa (gauge
pressure -1kgf/cm2).
e. When the procedures for vacuum pumping are finished, refrigerant shall be charged. If the vacuum level
reaches -0.1MPa (gauge pressure) or lower, the vacuuming process is then ended. Stop the vacuum pump
and place still for 1 hour. Then, check the vacuum level for any change. In case of any change, it indicates
that there is leakage. In this case, proceed to leakage detection and repair.
6.12 Refrigerant Charge
1)Calculation method for refrigerant charging
Refrigerant shall be charged according to calculated amount specified in engineering drawings.
Method for calculation of added refrigerant volume (based on liquid pipe)
178
DIGITAL MULTI VRF
INSTALLATION
Mass of refrigerant to be charged =∑ length of liquid pipe × refrigerant charge amount of every meter of
liquid pipe.
Amount of refrigerant charge for every meter of liquid pipe(kg/m)
Medium
R22
Φ25.4
Φ22.2
Φ19.05
Φ15.9
Φ12.7
Φ9.52
Φ6.35
0.54
0.41
0.29
0.187
0.12
0.06
0.03
0.35
0.25
0.17
0.11
0.054
0.022
R410a
Note: a. Standard pipe length is 15m. If refrigerant piping (L) is shorter than or equal to 15m, no additional
refrigerant is needed. If piping is longer than 15m (based on liquid pipe), more refrigerant shall be added.
The above table shows how much refrigerant shall be charged for every one additional meter of piping.
b. Electronic balance shall be used for refrigerant charge
c. Thickness of pipe wall shall be 0.5~1.0mm and pressure-bearing capability shall be 3.0MPa
d. The longer the piping, the more refrigerating capacity and heating capacity shall be weakened.
2)Steps of refrigerant charge are as follows:
a. The connecting hose of refrigerant cylinder shall be connected to the connector of the pressure gauge.
The valve VH shall be opened to discharge air in the hose. Then, the high pressure end of the pressure
gauge shall be connected to the refrigerant filling nozzle on the small valve of outdoor unit.
Pressure gauge connector valve
Gas liquid
Connector on gas side
Refrigerant cylinder
Connector on liquid side
Spring balance
b. Open pressure gauge valve VH, then fill liquid state refrigerant into the liquid pipe side until required
amount is reached.
If refrigerant can not be charged in system unless the unit is turned on, let the system run at full-load
cooling mode. Open VH and discharge air in the hose. The high pressure end of pressure gauge is connected
to the refrigerant filling nozzle on the small valve of outdoor unit. Open VL and charge gas state refrigerant
into the gas pipe until required charging amount is reached.
c.Observe electronic balance or spring balance. When required amount is reached, the valve shall be closed
very quickly and then source valve on the refrigerant valve shall be shut off.
d. The amount of charging refrigerant shall be recorded.
Refrigerant charge shall be recorded as per the following table.
Unit Mark
Amount of charging refrigerant(Kg)
Unit 1
Unit 2
………
Unit n
179
DIGITAL MULTI VRF
INSTALLATION
7 INSTALLATION OF ELECTRONIC EXPANSION VALVE PARTS
7.1 Direction Requirements
To ensure normal operation of the unit, please connect the electronic expansion valve sub-assembly as
shown below.
Ensure that the vertical arrow labeled on electronic expansion valve sub-assembly is pointed upward.
To Indoor
Unit
To Outdoor
Unit
Vertically
upward
Vertically
upward
To Indoor
Unit
√Arrow Upward
To Outdoor
Unit
X Arrow Downward
(1) Firstly, fix the electronic expansion valve sub-assembly properly. Several operating methods are
available:
Fix with screws
To Indoor
Unit
To Indoor
To Outdoor
Unit
Vertically Unit
upward
①! Suspend by using screw rod
To Outdoor
Unit
Vertically
upward
②Use screws to fix onto wall
Overhung
To Indoor
Unit
To Outdoor
Unit
To Indoor
Unit
Vertically
upward
To Outdoor
Unit
Vertically
upward
Caution: Never place overhung in air.
③Directly place on ceiling plane
(2) The indoor unit shall be firstly connected to a section of pipe (connected by nut). Then, connect
the
pipe
to
the
electronic
expansion
valve
sub-assembly
(by
welding).
Welding
To Indoor
To Outdoor
Unit
Unit
Vertically
upward
Welding
Pipe length: L>1m, but <1.5m
WARNING: The length of connection pipe must be 1m≤L≤1. 5m. The electronic expansion
180
DIGITAL MULTI VRF
INSTALLATION
valve sub-assembly must be connected to the indoor and outdoor unit in a direction as marked. If
connected in reverse direction, severe error will be caused to the unit.
(3) Pipe connection: Tighten the nuts with your hands correctly. Then, use another spanner to hold the
pipe joint on machine side and use torque wrench to tighten securely.
Hold the spanner
Pipe on indoor unit side
Rotate the spanner
(4) Cable connection of electronic expansion valve sub-assembly
① To avoid loosening and sagging down, please use strap (small) to fix the cable of electronic
expansion valve sub-assembly onto the pipe or other objects.
② When connecting the cable of electronic expansion valve sub-assembly, please take care to prevent
the cable from contact with the hot or humid objects.
Connect the mainboard Fix with strap
of indoor unit
To Indoor
To Outdoor
Unit
Unit
Vertically
upward
(5) Final treatment: The section where the pipe is connected must be wrapped for thermal insulation.
WARNING!
Please ensure the pipe is fully covered by sponge and not exposed in air. Condensing water will be
generated on the pipe if the thermal insulation is poor.
Thermal insulation sponge
Indoor unit
To Outdoor
To Indoor
Unit
Unit
Vertically
upward
181
DIGITAL MULTI VRF
INSTALLATION
8 INSTALLATION OF CONDENSATE PIPE
8.1 Material Quality Requirements for Condensate Pipe
Generally, the condensate pipe shall be water supply U-PVC pipe, adhered by using special glue. The other
materials available include: PP-R pipe, PP-C pipe and hot-dipped galvanized steel pipe. It is not allowed to
use aluminum plastic composite pipe.
8.2 Key Points for Condensate Pipe Installation
1).Work Order
Installation of
indoor unit
Sheathing of
thermal insulation
pipe on
condensate pipe
Connection of
drainage pipe
Thermal insulation of
drainage pipe
Water test
2). Determine the direction and elevation of condensate pipe before installation. To ensure the gradient
smooth and straight, avoid intersecting with other pipelines. The height of the clamp fixing the
pipe hanger frame shall be adjustable and fixed from the outer of thermal insulation.
3).Distance between hanger frames:
Outer diameter of water
pipe (mm)
ф≤25
32>ф≥25
ф≥32
800
1000
1500
Spacing between horizontal
pipes (mm)
Spacing between standpipes
(mm)
1500
2000
Each standpipe shall have two hanger frames at least.
4). The gradient of condensate pipe shall be over 1% and the gradient of main pipe shall not be less
than 0.3%, while there shall be no overhanging slope.
Over 1/100
5). When connecting the 3-way section of condensate pipe, the 2-way straight section on 3-way pipe shall
be on the same gradient. The two ends of 2-way section shall not have different gradient. See the
schematics below:
Wrong
connection
错误的接法
Correct
connection
正确的接法
6). Confluence toward the horizontal pipe shall be best from the upper. Back flow is easy to occur if
from the lengthwise direction.
182
DIGITAL MULTI VRF
INSTALLATION
Indoor Unit
Mounting of horizontal pipe
Main pipe
Main pipe
Main pipe
7)Do not tie the condensate pipe and refrigerant pipe together.
8) To ensure smooth drainage of condensate, a vent hole shall be set at the highest point of drainage
pipe.
9) Carry out water flow test and full water test after the pipe connection is completed. On one hand,
check if the drainage is smooth; on another hand, check the piping system for any leakage.
10) Steel sheath shall be provided to the pipe crossing the wall or slab. The pipe joint shall not be
positioned within the sheath. The steel sheath shall be flush with the wall surface or slab base, but
20mm higher than the slab base. The sheath shall not affect the pipe gradient. The clearance
between pipe and sheath shall be blocked by using flexible inflammable materials. The sheath shall
not be used as the supporting point of the pipe.
11) The joint of thermal insulation materials must be adhered by using special glue and then wrapped
with plastic tape having a width not less than 5cm to avoid condensing.
12). Ensure a gradient over 1% when connecting the drainage pipe to the indoor unit.
Gradient over 1/100
13) When connecting the drainage pipe to the indoor unit, please fix with the included pipe clamp and
do not use glue water, thus to ensure easy repair.
14) Installation requirements for auxiliary drainage pipe
Pipe clamp
Unit drainage pipe
Drainage PVC
pipe
Drainage hose
The auxiliary drainage pipe must be thermally insulated:
183
DIGITAL MULTI VRF
INSTALLATION
Thermal
insulation of
冷凝水管
condensate
保温层 pipe
Pipe 管盖
cover
15) The long drainage pipe may be fixed by using hanger bolts, thus to ensure a gradient of 1/100
(PVC cannot be bent).
The spacing between the supports of horizontal pipe is 0.8-1.0m. Twisting will be caused and thus air
bag will be formed if the spacing is too high. Once the air bag is formed, the pump can only compress
the air bag no matter how forcible it pushes, but there is no flowing water, thus resulting in abnormal
water level. This will cause flooding of the ceiling.
16). If the air flow of indoor unit is high, this might cause negative pressure and result in return suction
of outdoor air. Therefore, U-type water trap shall be designed on the drainage side of each indoor
unit.
Indoor unit.
‹
‹
‹
Install water trap as shown below
Install one water trap for each unit
Installation of water trap shall consider easy cleaning in the future.
184
DIGITAL MULTI VRF
INSTALLATION
Joint
Indoor unit.
Indoor unit.
Joint
17) Connection of drainage branch pipe to the standpipe or horizontal pipe of drainage main pipe
The horizontal pipe cannot be connected to the vertical pipe at a same height. It can be connected
in a manner as shown below:
N01:3-way connection of drainage pipe joint
3-way connection of
drainage pipe joint
NO2: Connection of drain elbow
Connection of
drain elbow
NO3: Connection of horizontal pipe
Connection of
horizontal pipe
Drainage pipe is requisite for air conditioner unit. During cooling, the moisture in the air will condense on
the surface of evaporator. Such condensing water must be drained out of the unit. Meanwhile, the drainage
pipe has an important role to determine if the air conditioner can plays its full functions.
18). All the condensate pipes must be installed at a distance over 500mm from the electric box of the
unit.
8.3 Installation of Drainage Pipe for Different Types of Indoor Unit
1) Duct-type Indoor Unit (Including General Static Pressure and Low Static Pressure)
185
DIGITAL MULTI VRF
INSTALLATION
a. Installation of drainage pipe
¾ The diameter of drainage pipe shall be equal to or higher than the diameter of connection pipe.
(PVC pipe: Dimension: Outer diameter 25mm, 32mm)
¾ The drainage pipe shall be short and has a down gradient of 1/100 at least, thus to avoid air bag.
¾ To ensure that the drainage hose will not be bent and has enough gradient, a distance of 1 ~
1.5m shall be kept between the hanger frames.
Gradient over 1/100
¾
Use drainage pipe and clamp.
Insert the drainage hose to the root. From the middle of white tape, tighten the clamp until the
tightening distance to the screw head is shorter than 4mm.
A. For thermal isolation, use sealing tape to wrap the drainage pipe and clamp.
B. The indoor drainage hose shall be thermally insulated.
Big sponge (accessory)
Clamp
Clamp (accessory)
Drainage hose
Sponge (grey)
Below 4mm
C. To prevent foreign articles from entering the pipe, please minimize the bend of pipeline, thus to
ensure cleanliness of the drainage elbow.
D. The drainage pipe must be wrapped with thermal insulation tube, thus to avoid condensing on the
outer surface of drainage pipe. See below for the thickness of thermal insulation tube.
Thermal insulation of
condensate pipe
Pipe cover
Drainage Pipe (mm)( Outer Dia)
Thickness of Thermal Insulation Materials (mm)
Φ17
≥15
Φ27
≥20
≥34.9
≥20
186
DIGITAL MULTI VRF
INSTALLATION
※ Notes:
E. The inclination of drainage hose① shall be within 75mm, so that the drainage insert will not bear
excessive force.
F. To connect the drainage pipes for multiple machines, please use the method of multi-pipe collection,
as shown below.
。
T-joint collecting
drainage pipe
Over 100mm
Fig. The specification of collecting drainage pipe shall be suitable to the working capacity of the unit
We may collect the drainage pipes of all the indoor units in one system (An outdoor unit and all the
indoor units connected to this outdoor unit are called one system), or collect the drainage pipes of all the
indoor units in several systems.
Notes: The ceiling height must be considered, and a specific gradient shall be ensured along the water
flow direction.
2)Cassette Type (Four-sided Outlet)
a. Installation of drainage pipe
¾ The drainage pipe shall be installed to ensure smooth flow of water.
¾ The diameter of drainage pipe shall be equal to or higher than the diameter of connection pipe (PVC
pipe) (exclusive of the rise section).
¾
¾
¾
¾
The drainage pipe shall be short and has a down gradient of 1/100 at least, thus to avoid air bag.
If the inclination of the drainage hose is insufficient, drainage rise pipe shall be mounted.
The installing height of drainage rise pipe shall be less than 280mm.
The drainage rise pipe shall be in right angle to the unit and the distance to the unit shall not exceed
300mm.
Roof
Hanger seat
Within 300mm
Below 280mm
Drainage hose
(accessory)
Drainage rise
pipe
Ceiling
¾
Below 500mm
Clamp (accessory)
The inclination of included drainage hose shall be within 75mm, so that the drainage insert will not
bear excessive force.
187
DIGITAL MULTI VRF
INSTALLATION
Drainage hose
(accessory)
Below 500mm
Below 75mm
¾
To prevent the drainage hose from dropping downward, hanger rods shall be erected every 1.0~1.5m.
Hanger rod
Gradient over 1/100
Incorrect
Correct
¾
¾
¾
Use the included drainage hose and clamp. Insert the drainage hose to the drainage port and tighten
the clamp.
For thermal insulation, wrap the big sponge to the drainage hose clamp.
The indoor drainage hose shall be thermally insulated.
Big sponge (accessory)
Clamp
Sponge (grey)
¾
Clamp (accessory)
Drainage hose
Below 4mm
To connect the drainage pipes for multiple machines, please use the method of multi-pipe
collection, as shown below.
Over 100mm
Introduce water here
for water test
T-joint collecting
drainage pipe
Fig. The specification of collecting drainage pipe shall be suitable to the working capacity of the unit
We may collect the drainage pipes of all the indoor units in one system (An outdoor unit and all the
indoor units connected to this outdoor unit are called one system), or collect the drainage pipes of all the
indoor units in several systems.
The ceiling height must be considered, and a specific gradient shall be ensured along the water flow
188
DIGITAL MULTI VRF
INSTALLATION
direction. The cassette-type indoor unit is provided with water pump, and the maximum lift of its drainage
pipe is 280mm.
¾ During installation, please take care that:
The diameter of drainage pipe connected to the indoor unit must meet the specifications. The pipe diameter
shall not be too small; otherwise the water may overflow.
The main drainage pipe depends on the number of indoor units. Generally, it is required to be equal to or
higher than ф35mm.
The drainage pipe shall be thermally insulated. The thickness of thermal insulation pipe must meet the
requirements. The clearance between thermal insulation pipes shall be sealed with adhesive sticker.
Please discharge the water to the ground drain, water closet or any other place easy to drain the water out.
b) After installation, check if the drainage is smooth.
3) Wall-mounted Type
Assemble the drainage pipe as shown below and take measures to prevent condensing. Improper
assembly of the drainage pipe may cause leakage, or even expose the furniture to moisture.
a) Assembly of drainage pipe
¾ To avoid air in water elbow, the drainage hose shall be kept as short as possible and inclined
downward, as shown below.
¾ During connection, please use PVC pipe of equal size higher than this size (Nominal Dia,: 20mm;
Outer Dia.: 26mm)
¾ The drainage pipe must be arranged in down inclination along water flow direction, thus to avoid air
bubble blocking. Take care not to arrange the pipe in twisting, protrusion or waveform. Do not put the
outlet of drainage pipe into water.
Protrusion
Twisting
Do not immerse in water.
¾
The extended section of drainage hose shall be wrapped with thermal insulation sheath when passing
the room.
Thermal insulation of
condensate pipe
Pipe cover
¾
Fig.3.41
After installation of the drainage pipe, be sure to make water test and check if the water can be
drained smoothly.
189
DIGITAL MULTI VRF
INSTALLATION
Drainage hose
Drainage hose
b. After piping work, check if the draining flow is smooth.
8.4 Test for Condensate Pipe
The water test for condensate pipe includes closed water test and drainage test. The closed water test
is focused on checking if the drainage pipe system is well sealed and if there is any leakage. The drainage
test is focused on checking if the drainage pipe system can drain water smoothly and thoroughly and
ensuring that there is no water deposit (except the specially designed water trap).
After connection of the drainage pipe is completed, firstly carry out closed water test. Seal the outlet
of drainage pipe with adhesive tape or plug. Then, fill water into the drainage pipe system form indoor unit
side. Stop filling after ensuring that all the drainage pipes are filled with water. After 24 hours, check all
the joints of water pipe for any leakage. If any, repair and reinstall. If no leakage, proceed to drainage test.
Remove the adhesive tape or plug from the drainage pipe. Check the water tray and drainage pipe of
indoor unit if the drainage is thorough and if there is any water deposit. If any, readjust it. If not, complete
the water test and proceed to the thermal insulation on all pipe joints.
8.5 Requirements of Heat Preservation
¾ Heat Insulation Materials
The thermal insulation material of obturator foam shall be used. Fireproof level: B1.
The thermal conductivity shall not be higher than 0.035w/ (m·k) when the average temperature is 0①.
¾ Thickness of thermal insulation layer
The thickness of thermal insulation layer on condensate pipe shall be over 10mm.
¾ The joint of thermal insulation materials must be adhered by using special glue and then wrapped with
plastic tape having a width not less than 5cm to avoid condensing.
¾ Thermal insulation is not required for the outdoor section of condensate pipe.
190
DIGITAL MULTI VRF
INSTALLATION
9 ELECTRICAL INSTALLATION
9.1 Precautions for Electrical Installation
Itemized Description of Cautions.
The electrical installation must be done by professional electricians.
The electrical installation must be done in accordance with applicable technical codes and other rules.
WARNING! Please make sure to install earth leakage circuit breaker. Earth leakage circuit
breaker must be installed to prevent electric shock or fire.
z
z
z
z
z
z
z
z
z
z
CAUTIONS!
The air conditioner must be securely earthed. Incorrect earthing may cause
electric shock or fire.
All the electric installations must be carried out by specialist technicians in accordance with the
local laws, rules and these instructions.
The indoor unit and outdoor unit shall use different power supplies. The indoor units under the
same system must be powered by a unified power source. All the indoor units can only be
controlled by one master power switch. Rated supply voltage and special circuit for air
conditioner must be used.
The earthing shall be secure. The earthing wire shall be connected to the special earthing device
on the construction. The installation must be done by specialist technicians. Never connect the
earth lead to the gas pipe, water pipe, lightening rod or telephone earth wire.
To avoid electric shock or any accident due to mal-operation, the air switch and shock-resistant
earth leakage circuit breaker that can cut off the power supply of the complete system must be
installed. The air switch shall have both the magnetic tripping and thermal tripping functions to
ensure protection against the short circuit and overload. Electric shock or fire might be caused if
no installation of earth leakage circuit breaker. Do not switch on the power before completion of
the electrical work. Make sure to cut off the power supply before repair.
In no case should the capacitor be used to improve the power factor.
Please use cable conduit for power cords.
Do not lay the electronic control cables (remote control and signal line) outside the machine with
other cables; otherwise the machine might become malfunctioned or failed due to electrical noise.
The power cord must be always connected to the power cord terminal board, and fixed by using
the lock connector included with the machine. Meanwhile, prevent them from contacting the
fitting pipe. The diameter of power cords shall be large enough. See below for the detailed
specifications. The damaged power cords and connection lines must be replaced with the
designated cables. When connecting the cable, please confirm that all the electrical components
inside the electric box shall have no coupling or terminal loosened. (Improper installation of
electric box cover may lead to potential water leakage, which will cause the unit abnormal or
short circuit).
Earth lead must be connected before connecting the power cord. An earth lead longer than the
power cord shall be provided.
For site wiring, please refer to the circuit diagram attached on the machine body.
191
DIGITAL MULTI VRF
INSTALLATION
9.2 Specifications of power cord & circuit breaker
Power supply
(V,Ph,Hz)
Capability of
circuit breaker
(A)
Min. sectional area
of earth lead (mm2)
Min. sectional area of
power cord (mm2)
GMV-R120W/Na-K
220-240V-1Ph-50Hz
16
4
4
GMVL-R120W/Na-K
220-240V-1Ph-50Hz
16
4
4
GMV-R160W/Na-M
380-415V-3Ph-50Hz
20
4
4
GMVL-R160W/Na-M
380-415V-3Ph-50Hz
25
6
6
GMV-R260W2/Na-M
380-415V-3Ph-50Hz
25
6
6
GMVL-R260W2/Na-M
380-415V-3Ph-50Hz
25
6
6
GMV-R300W2/Na-M
380-415V-3Ph-50Hz
32
6.0
6.0
GMVL-R300W2/Na-M
380-415V-3Ph-50Hz
32
6.0
6.0
GMV-R450W3/Na-M
380-415V-3Ph-50Hz
40
10.0
10.0
GMVL-R450W3/Na-M
380-415V-3Ph-50Hz
40
10.0
10.0
GMV-R560W4/Na-M
380-415V-3Ph-50Hz
50
16.0
16.0
GMVL-R560W4/Na-M
380-415V-3Ph-50Hz
50
16.0
16.0
GMV-R600W4/Na-M
380-415V-3Ph-50Hz
50
16.0
16.0
GMVL-R600W4/Na-M
380-415V-3Ph-50Hz
80
16.0
35.0
GMV-R860W6/Na-M
380-415V-3Ph-50Hz
80
16.0
35.0
380-415V-3Ph-50Hz
80
16.0
35.0
GMV-R900W6/Na-M
380-415V-3Ph-50Hz
80
16.0
35.0
GMVL-R900W6/Na-M
380-415V-3Ph-50Hz
80
16.0
35.0
Model
GMVL-R860W6/Na-M
9.3 Wiring Sketch Map
9.3.1 Connection of power cord
Wiring Sketch Map for 3-Phase Outdoor Unit
Wiring Sketch Map for Single-Phase Outdoor Unit
Notes: a) For the pin silk print on mainboard for connection of communication line, please refer to the lead diagram of the
unit.
b) The outdoor signal line leading out of the electric box must be separated from the power cord and shall not be tied
together. They must be kept at a distance of 10cm to the least. If they cannot be routed separately in actual
application, make utmost to avoid routing in parallel.
C).The outdoor signal line must be fixed by using the cable clamp A or lock connector B in the electric box. As
shown:
(A)
(B)
192
DIGITAL MULTI VRF
INSTALLATION
Loosen the two screws fixing the cable clamp A
and insert the signal line through the cable clamp.
Then, tighten the signal line with screws. If still
loose, use a strap to tie at the position where the
signal line passes through the cable clamp.
Open the bottom of lock connector and insert the signal line
and other light-current line (temperature sensor, pressure
sensor) together through the hole of lock connector. Then,
rotate in reverse direction to tighten the bottom of lock
connector, making the cable-cross hole shrink slowly until all
the lines are locked.
9.3.2 Connection of communication line
1)Connection of communication line of single outdoor unit
outdoor unit
Terminal board
outdoor unit
Communication
twisted-pair
Terminal board
Power supply
outdoor unit
Communicati
on
twisted-pair
Power supply
Terminal board
outdoor unit
Communicati
on
twisted-pair
Power supply
Terminal board
Communication
twisted-pair
Power supply
Note: The communication line to be installed on the last indoor unit is wire (resistance compatible). The
indoor unit as shown is single-phase only. For the indoor unit using 3-phase electric heater, the power cable
specifications and power connection shall be based on the circuit diagram attached on the unit.
2)Connection of communication line of single outdoor unit with transition board
outdoor unit
outdoor unit
outdoor unit
Mainboard
Power
supply
Communic
ation wire Terminal board
Terminal board
Communication wire
To 1# indoor unit of Group 1
Mainboard
Communication
wire
Mainboard
Terminal board
Communication wire
To 2# indoor unit of Group 1
Communication wire
To N# indoor unit of Group 1
The dotted section is the wire to be connected on user site. For the diameter and other parameters
of power cable, please refer to the Installation and Operating Manual. The mainboard of outdoor
unit contains module address and diversion address, to be determined and dialed on site. One
outdoor unit module can connect to Max. 16 indoor units, to be determined on site. One group
comprises the indoor units (Max. 16 sets) driven by one outdoor unit module.
Figure
Wiring Sketch Map between Outdoor Units
One outdoor unit module can connect to Max. 16 indoor units. When the number of indoor units to be
connected is ≤16, all the indoor units may be connected to the same outdoor unit module, while it is
allowed to connect part of them to different outdoor unit module. When the number of indoor units in the
system is >16 but ≤32, the indoor units may be connected to two or more outdoor unit modules; when the
number of indoor units in the system is >32 but ≤48, the indoor units may be connected to three or more
outdoor unit modules; and so on. Different outdoor unit modules shall be differentiated by using address
dial-up and diversion address. For details, please refer to the Description of Dial-up Switch on Outdoor
End.
During engineering installation, the communication wire shall be connected in two steps: 1)
Connection between outdoor mainboard and indoor unit; and 2) Connection between modules. For details,
please refer to the Wiring Sketch Map between Outdoor Units.
A. Connection between outdoor mainboard and indoor unit: Insert the 2-cord 3-pin wire
(communication) connected to indoor unit into the 3-pin holder on outdoor mainboard (For outdoor units,
the communication wire is connected in series). Then, insert another end into the 3-pin socket on the
mainboard of the first indoor unit (For indoor unit, the communication wire is connected in series).
193
DIGITAL MULTI VRF
INSTALLATION
B. Communication between modules: For multi-module combination, insert one end of 2-cord 4-pin
wire (communication) into the 4-pin holder on the outdoor mainboard of one module, and insert another
end into the 4-pin holder on the outdoor mainboard of another module.
9.4 Dial-up of Unit
The indoor unit is provided with three dial-up, i.e. address dial-up, capacity dial-up and function
dial-up. Among them, the address dial-up and function dial-up shall be set on installation site.
The duct-type unit is taken as example to illustrate the position of three dial-up:
9.4.1 Dial-up of indoor unit mainboard and wire remote controller
1)Address code
Address dial-up must be set for the multi indoor units; otherwise the abnormal communication will be
caused to the unit. The address code has 4-bit dial-up in total. The highest address is 16 and the lowest
address is 1
NOTES! To use multiple indoor units in parallel, make sure to change the setting of address
code before installation and guarantee that the address code of each indoor unit must be different
(The address code is located on the mainboard of indoor unit). If wired controller is used, make sure
to dial the address code of wired controller to the position same as the address code on corresponding
indoor unit. (The address code of wired controller is located on the back of wired controller)
☆ Below is factory default setting:
194
DIGITAL MULTI VRF
INSTALLATION
The default setting of address dial-up code is 0000 and the address is 1 (See above for the position of
dial lever).
☆ Dial-up Value
The dial-up value of address code is set in binary system. The dial-up value is “0” when the lever is
dialed to “ON” end; the dial-up is “1” when the lever is dialed to numerical end on opposite side. For
number 4~1 on the address code, the dial-up #4 refers to high bit and the dial-up 1# refers to low bit.
Dial-up table(dial-up switch with 4 bit)
Bit 4
Bit 3
Bit 2
Bit 1
Address
0
0
0
0
1
0
0
0
1
2
0
0
1
0
3
0
0
1
1
4
0
1
0
0
5
0
1
0
1
6
0
1
1
0
7
0
1
1
1
8
1
0
0
0
9
1
0
0
1
10
1
0
1
0
11
1
0
1
1
12
1
1
0
0
13
1
1
0
1
14
1
1
1
0
15
1
1
1
1
16
Example 1: If the dial value is “0111”, this represents that the address is “8”, the pins 1, 2 & 3 of the
dial switch are dialed to the numerical end, and the pin 4 is dialed to “ON”.
Example 2: If the dial value is “1010”, this represents that the address is “11”, the pins 2 & 4 of the
dial switch are dialed to the numerical end, and the pin 1 & 3 are dialed to “ON”.
See below:
Address 8, dial-up value 0111
Address 11, dial-up value 1010
2)Address code about capacity
On the mainboard of indoor unit, two 4-bit DIP switches are used to distribute the address and capacity
of indoor units. The 4-bit DIP switch (marked with “capacity” below) used for setting the capacity of
indoor units is factory set before shipment of indoor unit, while it is covered by sealant, so that it
cannot be changed by the user.
☆ Below is factory default setting:
The default Capacity dial-up is the maximum capacity of indoor unit. As shown above, the capacity is
(See above for the lever position)
195
DIGITAL MULTI VRF
INSTALLATION
☆ Dial-up Value
The dial-up value of capacity code is set in binary system. The dial-up value is “0” when the lever is
dialed to “ON” end; the dial-up is “1” when the lever is dialed to numerical end on opposite side. For
number 4~1 on the capacity code, the dial-up #4 refers to high bit and the dial-up 1# refers to low bit.
Dial-up Table (4-bit Dial-up Switch)
Bit 4
Bit 3
Bit 2
Bit 1
Capacity:
0
0
0
0
20
0
0
0
1
25
0
0
1
0
30
0
0
1
1
35
0
1
0
0
40
0
1
0
1
45
0
1
1
0
50
0
1
1
1
60
1
0
0
0
224
1
0
0
1
70
1
0
1
0
80
1
0
1
1
90
1
1
0
0
100
1
1
0
1
112
1
1
1
0
140
1
1
1
1
280
3)Functional dial switch S7
Functional dial switch S7
Dial-up
Switch
Functional Description:
1(S / R)
Setting of memory mode
2(L / I)
Setting of control mode
3(M / S)
4(I / O)
5(L / H)
Setting of master / slave
indoor unit
Setting of ambient
temperature acquisition
point
Setting of high / low static
pressure fan
Dial-up Setting
0 (ON Position)
1
Standby (S)
Wired control
(L)
Master indoor
unit (M)
Restore (R)
Remote control
(I)
Slave indoor
unit (S)
Air inlet (I)
Receiver (O)
Low static
pressure (L)
High static(H)
Functional description of function dial-up:
Dial-up switch 1 (S/R): Setting of memory mode, including the standby mode and restoration mode. The
standby mode refers to that the previous parameters will be kept but the unit will not
run automatically after the power supply is resumed. This setting is factory defaulted
(dial-up switch pulled to “ON” position). For example, if the parameters of an indoor
unit set before power shutdown are High Fan and 24①, the unit will be under standby
state after the power supply is resumed and after the unit is manually started, the
parameters will remain as High Fan and 24①. The restoration mode refers to that not
only the previous parameters will be kept, but also that the unit can start automatically
after the power supply is resumed. But if the unit is under STOP state before power
shutdown, it will be also under STOP state after the power supply is resumed.
Dial-up switch 2 (L/I): Setting of control mode, including wired control and remote control. The wired
control mode refers to that the indoor unit is controlled from wired controller (hand
controller). This setting is factory defaulted (dial-up switch pulled to “ON” position).
When the setting is wired control mode, the function dial-up on S7 for “setting of
memory mode” and “setting of master / slave indoor unit” will be disabled. These two
196
DIGITAL MULTI VRF
INSTALLATION
settings can be done from the wired controller directly. The remote control mode refers
to that the indoor unit is controlled from remote controller. When the setting is remote
control mode, its function dial-up must be set on S7.
Dial-up switch 3 (M/S): The setting of master / slave indoor unit refers to the master / slave setting of
indoor run mode, mainly used to meet the needs of special people on priority (e.g.
leader, patients, etc). The factory default setting is that all indoor units are master
(dial-up switch pulled to “ON” position).
When all the indoor units are set as slave, the outdoor unit will run according to the
mode of slave indoor unit that is firstly started. If the mode of slave indoor unit started
later has in conflict against the mode started earlier, the system will display mode
conflict error, so that the indoor unit started later cannot work. In this case, the run
mode of the unit is decided by the slave indoor unit that is firstly started.
When only one indoor unit is set as master, no matter if the master indoor unit is firstly
started or not, the slave indoor unit will give out mode conflict error as long as its mode
is in conflict against the mode of master indoor unit (except that the master indoor unit
is stopped). In this case, the unit run according to the mode of master indoor unit on
priority.
When several indoor units are set as master, the mode of master indoor unit with a
lower address code will be taken as the master run mode of the unit. when the master
indoor unit with the lowest address code is changed from STOP state to RUN state, the
mode of other master indoor units or slave indoor units shall be kept identical to its
mode; otherwise the system will give out mode conflict error. Therefore, when there are
several master indoor units, the address code of the unit shall be set from lower to
higher according to priority level.
Dial-up switch 4 (I/O): Setting of ambient temperature acquisition point. This setting is mainly used when
the temperature of air conditioner area differs largely from the air inlet temperature of
the unit. Meanwhile, this setting is only valid when the receiver is connected, including
the setting of temperature acquisition point at air inlet and setting of the temperature
acquisition point at receiver head. The factory default setting is acquisition of air inlet
temperature (dial-up switch pulled to “ON” position).
Dial-up switch 5 (L/H): Setting of high / low static pressure fan. This setting includes the setting of high
static pressure fan and low static pressure fan, adjusted as needed for the project. The
factory default setting is low static pressure fan (dial-up switch pulled to “ON”
position).
Cautions:
1)The above settings must be done under power shutdown state.
2)The dial-up switch of function code is classified into 3-bit code, 4-bit code and 5-bit code. The 4-bit code
or 5-bit code is used for duct-type unit only (including multi duct-type unit and 1-to-1 duct-type unit).
3)When the “setting of control mode” is “L”, the function dial-up for “setting of memory mode" and
“setting of master / slave indoor unit” will be disabled. When the “setting of control mode” is “I”, this
function dial-up setting is enabled.
4)The dial-up switch shall be put to position correctly, and shall not be put to middle position. Dialing of
the switch to “ON” position indicates “0” and the dialing to opposite direction indicates “1”.
5)After dialing up, please mark the address code of the unit(√)
197
GREE COMMERCIAL AIR CONDITION
DIGITAL MULTI VRF
MAINTENANCE
198
DIGITAL MULTI VRF
MAINTENANCE
MAINTENANCE
1 TROUBLE TABLES
1.1 Trouble Display of Indoor Unit
1.1.1 Trouble display of wire remote controller
Error
Error Code
button locked
CC
Indoor ambient temperature sensor error
F0
Indoor tube-inlet sensor error
F1
Indoor tube-middle sensor error
F2
Indoor tube-exit sensor error
F3
Outdoor ambient temperature sensor error
F4
Indoor tube-inlet sensor error
F5
Indoor tube-middle sensor error
F6
Outdoor tube-exit sensor error
F7
Exhaust temperature sensor 1(Fixed-frequency)error
F8
Exhaust temperature sensor 2(Digital)error
F9
Oil temperature sensor 1(Fixed-frequency)error
FA
Oil temperature sensor 2(Fixed-frequency)error
Fb
High-pressure valve error
Fc
Low-pressure valve error
Fd
High-pressure protection
E1
Prevention against low temperature
E2
Low-pressure protection
E3
Exhaust Overtemperature
E4
Overcurrent Protector
E5
Communication error
E6
Mode conflict
E7
Water-full protection (Cassette)
Eb/E9
Remote lock
EE
Auxiliary heater error
EH
Marking of master hand controller
HO
Marking of slave hand controller
SL
Marking of conflict against the effective master hand controller
CL
No master indoor unit code
No
199
DIGITAL MULTI VRF
MAINTENANCE
1.1.3 Trouble display of mainboard LED of cassette type indoor unit
Trouble LED
Trouble name
Electrical source LED
Operation LED
Tube-inlet sensor error
○
●
Tube-middle sensor error
○
Tube-exit sensor error
○
Room sensor error
○
Defrost
○
Antifreeze
●
Water-full protection
●
Mode conflict
●
Timing LED
○
○
●
●
○
Communication error
Outdoor unit failure
●
●
Auxiliary heater error
○
○
Legend: bright ○; dark ●; blink
1.1.4 Trouble display of mainboard LED of wall mounted type
¾ GMV-Rh22G/Na-K, GMV-Rh28G/Na-K, GMV-Rh36G/Na-K, GMV-Rh45G/Na-K, GMV-Rh50G/Na-K,
GMV-Rh56G/Na-K
Error
Antifreeze
protection
Outdoor
ambient
temperature
sensor error
Outdoor
tube-inlet
sensor error
Outdoor tube-inlet
sensor error
Outdoor tube-exit
sensor error
Indoor ambient
temperature
sensor error
Error
Code
E2
F4
F5
F6
F7
F0
Error
Exhaust
overtemperature
Low-pressure
protection
Overcurrent
Protector
High-pressure
protection
Exhaust temperature
sensor 1
(Fixed-frequency)
error
Indoor
tube-inlet
sensor error
Error
Code
E4
E3
E5
E1
F8
F1
Error
Indoor
tube-middle
sensor error
Indoor
tube-exit
sensor error
Exhaust
temperature
sensor 2
(VRF)
error
Compressor top
casing sensor 1
(Fixed-frequency)
error
Compressor top
casing sensor 2
(VRF)error
Communication
error
Error
Code
F2
F3
F9
FA
Fb
E6
Error
High-voltage
sensor error
Low-voltage
sensor error
Mode
conflict
Error
Code
Fc
Fd
E7
¾ GMV-Rh71G/Na-K, GMV-Rh80G/Na-K:
Trouble LED
Error
Electrical source LED
Operation LED
Tube-inlet sensor error
○
●
Tube-middle sensor
error
○
Tube-exit sensor error
○
Room sensor error
○
Defrost
○
Timing LED
○
○
●
200
DIGITAL MULTI VRF
MAINTENANCE
Antifreeze
●
Mode conflict
●
●
○
Communication error
Outdoor unit failure
●
●
Auxiliary heater error
○
○
Legend: bright ○; dark ●; blink
1.1.4 Trouble display of floor ceiling type
1.1.4.1 Trouble display of mainboard LED of floor ceiling type
Trouble LED
Error
Electrical source LED
Error
Tube-inlet sensor error
○
●
Tube-middle sensor error
○
Tube-exit sensor error
○
Room sensor error
○
Defrost
○
Antifreeze
●
Mode conflict
●
Electrical source LED
○
○
●
●
○
Communication error
Outdoor unit failure
●
●
Auxiliary heater error
○
○
Legend: bright ○; dark ●; blink
1.1.4.2 Trouble display of mainboard numerical tube of floor ceiling type
Error
Error Code
Error
Error Code
High-pressure protection
E1
Indoor tube-exit sensor error
F3
Prevention against low temperature
E2
Outdoor ambient temperature sensor error
F4
Low-pressure protection
E3
Indoor tube-inlet sensor error
F5
Exhaust overtemperature
E4
Outdoor tube-middle sensor error
F6
Overcurrent Protection
E5
Outdoor tube-exit sensor error
F7
Error with exhaust temperature sensor 1
(fixed-frequency)
Error with exhaust temperature sensor 2
(digital)
Error with oil temperature sensor 1
(fixed-frequency)
Error with oil temperature sensor 2
(digital)
Communication error
E6
Mode conflict
E7
Mode conflict
Eb
Indoor ambient temperature sensor
error
F0
Indoor tube-inlet sensor error
F1
High-pressure valve error
FC
Indoor tube-middle sensor error
F2
Low-pressure valve error
Fd
Auxiliary heating protection
EH
F8
F9
FA
Fb
1.2 Trouble and State Display of Mainboard LED of Outdoor Unit
Definition:
z
LED4, LED3, LED2, LED1: Fault indicator (yellow)
201
DIGITAL MULTI VRF
MAINTENANCE
z
LED5: Run indicator (green), bright when the unit runs normally and dark when the unit is stopped.
z
LED6: Power indicator (red), bright when the power is connected and dark when the power is
disconnected.
1.2.1 Trouble of elements
Error Description
Display of Error Lamp
LED6
LED5
LED4
LED3
LED2
LED1
Fault display
Low-pressure valve error
○
○
○
Variable-frequency top casing
temperature sensor error
○
○
●
Radiating fin sensor abnormal
○
○
○
○
E5
Driver board ambient temperature
sensor error
○
○
●
○
/
High-pressure valve error
○
○
○
●
Fixed-frequency compressor
abnormal
Error with fixed oil temperature 3#
sensor
Error with fixed exhaust temperature
3# sensor
Error with outdoor coil 2# inlet
temperature sensor
Error with outdoor coil 2# middle
temperature sensor error
Error with outdoor coil 2# outlet
temperature sensor
Outdoor ambient temperature sensor
error
Error with outdoor coil inlet
temperature sensor
Error with fixed oil temperature 2#
sensor
Outdoor coil middle temperature
sensor error
Error with outdoor coil outlet
temperature sensor
Error with fixed exhaust temperature
2# sensor
Error with fixed exhaust temperature
sensor
Error with digital exhaust
temperature sensor
Error with fixed oil temperature
sensor
Error with digital oil temperature
sensor
Fd
●
/
Fc
○
○
/
○
○
●
/
○
●
○
○
/
○
●
○
●
/
○
●
○
○
●
●
○
/
○
●
●
●
F4
○
●
●
○
●
○
/
○
●
●
F6
○
●
/
F5
F7
○
●
○
/
○
●
●
F8
○
●
○
F9
●
Fa
Fb
○
Legend: bright ○; dark ●; blink
202
DIGITAL MULTI VRF
MAINTENANCE
1.2.2 System Errors
Error Description
Display of Error Lamp
LED6
Fault display
LED4
LED3
LED2
○
○
○
○
○
○
●
Low-pressure protection
○
●
●
Exhaust protection
○
●
●
E4
Oil temperature higher than 80①
○
○
/
No-refrigerant protection
○
High-pressure protection
○
The temperature of radiating fin is
too high
Top casing overtemperature
protection
LED5
LED1
E5
E4
●
○
●
●
E3
●
/
●
E1
Legend: bright ○; dark ●; blink
1.2.3 Controlling trouble
Display of Error Lamp
Error Description
LED6
LED5
LED4
LED3
LED2
LED1
Fault
display
○
○
E5
○
E5
DC input voltage is too high
○
○
○
The current test circuit is failed
○
○
○
Drive error of outdoor fan
○
○
●
○
○
/
Drive voltage protection of outdoor fan
○
○
●
○
●
/
Drive current protection of outdoor fan
○
○
●
○
Module overheating protection of outdoor fan
○
○
●
●
○
/
Motor overheating protection of outdoor fan
○
○
●
●
●
/
AC current protection on AC input side
○
○
○
●
/
Compressor overcurrent
○
○
○
DC input voltage is too low
○
○
Failed to start
○
●
○
PFC abnormal
○
●
Clogged
○
Drive module reset
/
E5
○
E5
○
○
E5
○
○
●
E5
●
○
○
○
●
○
●
○
E5
Motor out of synchronization
○
●
○
●
●
E5
Open phase, tripping
○
●
○
●
Overcurrent or drive system abnormal
○
●
IPM abnormal
○
Overspeed
Sensor connection protection (The current
sensor is connected to corresponding U or V
phase)
Temperature drift protection (Prevent the
outdoor ambient temperature from changing
too high, which might result in that the
temperature drift of sensor is too high)
AC contactor protection (AC contactor not
closed)
The temperature of radiating fin is too high
E5
E5
●
●
E5
○
○
○
E5
○
○
○
●
/
○
○
○
○
○
●
○
/
○
○
●
●
/
○
○
○
○
/
E5
Legend: bright ○; dark ●; blink
203
DIGITAL MULTI VRF
MAINTENANCE
1.2.4 Communication Errors
Display of Error Lamp
Error Description
LED6
The dial-up number of modular multi
VRF is inconsistent to the number of
units communicated.
In case that one module among several
modules is failed, the other outdoor units
will display this error. If it is the error
with outdoor unit, it will only display its
own error.
Mode conflict (error with communication
between 1-32 outdoor mainboard and
sub-unit)
Communication error between outdoor
board and fan speed regulation board
LED5
LED4
LED3
LED2
LED1
Fault display
○
●
○
○
/
○
●
○
●
/
○
●
●
○
●
○
/
Communication error
○
●
●
E6
Fault from variable frequency drive to
main control communication
○
○
●
●
/
E5
●
Legend: bright ○; dark ●; blink
1.2.5 State display
Error Description
Display of Error Lamp
LED6
Defrost
○
Oil return
○
Oil equilibrium
○
Forcible cooling
●
LED5
LED4
LED3
LED2
LED1
●
/
○
●
Forcible heating
Forcible stop
Fault display
/
○
/
●
●
●
●
/
●
●
●
●
/
●
●
●
●
/
/
Vacuum mode
●
●
The current module is master module
○
○
●
●
●
○
/
Online testing
○
○
●
●
○
●
/
Comprehensive performance
coefficient testing
○
○
●
●
○
○
/
Legend: bright ○; dark ●; blink
1.2.6
Number of indoor units display
Number of indoor units
Display of Error Lamp
LED6
LED5
LED4
LED3
LED2
LED1
1
●
●
●
●
●
○
2
●
●
●
●
○
●
3
●
●
●
●
○
○
4
●
●
●
○
●
●
5
●
●
●
○
●
○
6
●
●
:
:
:
:
:
:
62
○
○
63
○
●
○
○
●
:
:
:
:
:
:
:
○
○
○
●
○
○
○
:
○
○
Legend: bright ○; dark ●; blink
204
DIGITAL MULTI VRF
MAINTENANCE
1.3 Trouble Display of Outdoor Unit Transition Board
Definitions:
1.LED2 is power indicator (red) (bright when the power is connected and dark when the power is
disconnected).
2.LED3 is run indicator (green) (bright when the indoor unit runs normally and blink when the indoor unit
is stopped).
3.In case of error, LED2 and LED3 will blink alternatively.
Error
Error Code
Error with evaporator 2# coil-inlet sensor [Note]
b5
Error with evaporator 2# coil-middle sensor [Note]
b6
Error with evaporator 2# coil-exit sensor [Note]
b7
Error with fixed-frequency compressor 2# exhaust sensor error [Note]
b8
Error with fixed-frequency compressor 3# exhaust sensor error [Note]
b9
Error with fixed-frequency compressor 2# oil sensor error [Note]
bA
Error with fixed-frequency compressor 3# oil sensor error [Note]
bb
Outdoor ambient temperature sensor error
F4
Outdoor tube-inlet sensor error
F5
Outdoor tube-middle sensor error
F6
Outdoor tube-exit sensor error
F7
Error with exhaust temperature sensor 1 (fixed-frequency)
F8
Error with exhaust temperature sensor 2 (digital)
F9
Error with oil temperature sensor 1 (fixed-frequency)
FA
Error with oil temperature sensor 2 (digital)
Fb
High-pressure valve error
Fc
Low-pressure valve error
Fd
No-refrigerant protection
FE
High-pressure protection
E1
Antifreeze
E2
Low-pressure protection
E3
Exhaust overtemperature (overtemperature protection against oil temperature 80①)
E4
Overcurrent Protection
E5
Communication error
E6
Mode conflict
E7
EA
Oil solenoid valve protection
Note: The "modular system of 3 or 4 compressors, e.g. modular type 600” or the “non-modular
outdoor unit system of 3 or 4 compressors, e.g. GMV-R620W4/A, GMV-R420W3/A……” contains
two evaporators. In case that the second evaporator is failed, the adaptor will display error code
b5~bb.
205
DIGITAL MULTI VRF
MAINTENANCE
1.4 Trouble Display of Driver Board LED
Green
Continuous quick
blinking counts of LED1
(red): Note 4
Remarks
●
Blink 1 times every 250ms
No abnormality
LED1
LED2
LED3
Red
Yellow
Normal
●
Module protection
●
Error Description
High-pressure
protection
●
Blink 3 times every 250ms
Current protection
Frequency fluctuation
●
Emergency stop
●
Communication error
●
Loss-of-synchronization
protection
Over-frequency
protection
●
●
○
○
○
○
Sensor error
Sensor connection
protection
○
Radiating fin
temperature protection
(module overheat
protection)
○
Temperature drift
protection
○
AC contactor protection
●
Radiating fin
temperature sensor
Motor overheat
protection
Module overcurrent,
undervoltage or in-built
overheating, FO pin output
Supply voltage too low or too
Blink 4 times every 250ms
high
Blink 2 times every 250ms
Working current too high
Error between working
frequency and target frequency
too high
Emergency braking subject to
the command of upper unit
Failed to communicate with
Blink 5 times every 250ms
upper unit
The rotor positioning loses
function and synchronization
Working frequency exceeding
upper limit
Zero-point deviation of sensor
too high
The current sensor is connected
to corresponding U or V phase
○
○
Protection when the
Blink 6 times every 250ms temperature of radiating fin is
too high
Prevent the outdoor ambient
temperature from changing too
high, which might result in that
the temperature drift of sensor
is too high
AC contactor not closed
○
○
●
○
Not connected or short circuited
●
Legend: bright ○; dark ●; blink
Remarks:
1. The silk print is unified as: LED1 – Red; LED2 – Yellow and LED3 – Green.
2. The red LED1 is the indicator showing that the variable-frequency board works normally (blink during normal operation).
3. The indicator state is classified into BRIGHT, BLINK and DARK, which are combined to indicate the error. BLINK /
DARK and easily memorable combination will be used firstly.
4. Drive board error indicator for DC variable-frequency fan: (Applicable to mainboard WZS901; Code 30229004) This
mainboard has one error indicator LED1 (red) only. The error is judged from the counts of continuous quick blinking. During
normal operation, the indicator blinks every 1s.
Note: The code E5 represents different errors. Therefore, then the wired controller of indoor unit or the
lamp displays E5 protection, please do not immediately cut off the power of complete unit, but checking
the records of mainboard, adaptor board and drive board on outdoor side and observing the detailed display
of the error lamp to identify the specific error protection.
206
DIGITAL MULTI VRF
MAINTENANCE
2 FLOW CHART OF TROUBLESHOOTING
The repair personnel shall collect the error information as more as possible for careful study and list
those electric or system parts that might cause the error. Then, the repair personnel shall be able to identify
the specific cause of error and find out the problem parts.
Keep an eye on the complete equipment. Do not restrict to a part, but taking care to check the state of
complete equipment.
Study from the simple point. To analyze, judge and identify the cause of trouble, please start from the
simple operation and finally proceed to such complicated operations as discharge of refrigerant,
disassembly of equipment, replacement of parts and filling of refrigerant. Be prudent to find out the cause.
The unit might be incurred to multiple errors, and such errors might be caused by multiple reasons. It is
also possible that one error is developed into multiple errors. Therefore, a comprehensive analysis system
shall be set up to ensure that the result of judgment is more correct and reliable.
Note: The code E5 represents different errors. Therefore, then the wired controller of indoor unit or the
lamp displays E5 protection, please do not immediately cut off the power of complete unit, but checking
the records of mainboard, adaptor board and drive board on outdoor side and observing the detailed display
of the error lamp to identify the specific error protection.
207
DIGITAL MULTI VRF
MAINTENANCE
1) High-pressure protection
高压保护
High-pressure
protection
用压力表
Use pressure gauge to
测量其压力是否为
measure if the pressure is
really high?
真正高压?
No
否
Yes
是
更换室外机主板
Replace
the mainboard of outdoor unit
否
No
Yes
是
检查
Check if the operation
室内机运行模式设定
mode of indoor unit is
set properly?
是否恰当?
测量if the
Measure
pressure switch is
压力开关是否
normal?
正常?
否
No
参照室内机说明书
Refer
to the Instruction Manual for
Indoor Unit
更换压力开关
Replace
the pressure switch
是
Yes
检查
Check if the gas valve
大小阀门是否完全
and liquid valve are
fully open?
打开?
否
No
完全打开阀门
Fully open the valve
Yes
是
检查室外
Check if the front panel of
机面板是否盖上
outdoor unit is covered
tightly?
No
否
Cover up盖好面板
the front panel properly
封严?
Yes
是
检查室内、
Check if the air inlet and outlet
of the indoor and outdoor
外机换热器进出风
exchanger is smooth?
No
否
清除障碍物
Remove
the obstructions
是否顺利?
Yes
是
检查
Check if the indoor
and outdoor fans run
室内、外机风机是否
normally?
运行?
No
否
测量风机电机和信
Measure
the fan motor and
signal input
号输入情况
否
测量扫风电机和信
Measure
the swing motor and
signal input
号输入情况
Yes
是
检查室内
Check if the indoor
swing louver is fully
扫风叶片是否完全
open?
打开?
Yes
是
检查室外机
Check if the capacity output of
outdoor unit is equal to the
容量输出与室内机容
capacity demand of indoor
units?
量需求相同?
No
否
Refer
to the dial-up of indoor and outdoor unit
参照室内外机拨码
是
Yes
检查室内
Check if the indoor
electronic expansion valve
电子膨胀阀动作是否
can work normally
正常?
No
否
使阀体和线圈啮合
Engage
the valve body with the coil
Yes
是
检查室内外
Check if the indoor /
过滤网或换热翅片是
outdoor filters or radiating
fins are dirty or blocked?
否有脏堵?
Yes
是
Refer参照维修与保养
to the Repair and Maintenance
否No
The 系统管路有堵塞
system pipe is blocked
Focus
on checking the inlet and outlet of the connection between indoor units and main
主要检查各室内机与主管连接的进出口,还有室内、外机的电子膨胀
pipe. Also focus on checking the electronic expansion valve of indoor unit and outdoor
阀等处。更换电子膨胀阀、干燥过滤器等零件。
unit.
Replace the electronic expansion valve, drying filter and other parts
208
DIGITAL MULTI VRF
MAINTENANCE
2) Low-pressure protection
低 压 保protection
护
Low-pressure
用压力
Use pressure gauge to
表测
量 压if力
否真正
measure
the是
pressure
is really
为
低 压low?
?
No
否
参 to
照low
低压
传感器
故 障error
Refer
pressure
sensor
Yes
是
检查
Check if the refrigerant in
系the
统 system
中制冷
剂 low?
量是否
is too
太少?
Yes
是
Add
nominal
依
据refrigerant
铭 牌 所 标according
称 的 制 to
冷the
剂量
和 refrigerant volume
on nameplate and the calculated charge volume
计算的制冷剂追加量来加注制冷剂
否No
检查
Check if the operation
室 内mode
机运
模式
设定
of 行
indoor
unit的
is set
properly?
是否
恰当?
No
否
室Instruction
内机说明
书 for Indoor Unit
Refer参
to照
the
Manual
Yes
是
检查室外
Check if the gas valve and
机liquid
大小
阀门
是否完
valve
of outdoor
unit全
are打
fully
开open?
?
No
否
完 全open
打 开the
阀valve
门
Fully
是Yes
检 front
查 panel of
Check if the
outdoor
室外
机 面unit
板is是covered
否盖上
tightly?
密封?
No
否
好front
面 板panel properly
Cover up盖
the
Yes
是
检查室内、
Check if the air inlet and outlet
外机
器进
风是否
of 换
the 热
indoor
and出
outdoor
exchanger
smooth?
顺 利is ?
否
No
清 除the
障碍
物
Remove
obstructions
Yes
是
检查
Check if the indoor and
室outdoor
内、外
风normally?
机是否
fans机
run
运行?
Yes
是
测 量 风the
机fan
电机
和 and
Measure
motor
信 号signal
输 入input
情况
否No
检查室内
Check if the indoor swing
机 扫louver
风 叶is片
是open?
否完全
fully
打开?
No
否
测 量 扫the
风swing
电 机 motor
和
Measure
input
信and
号 signal
输入情
况
是Yes
检查室外机
Check if the capacity output of
容量
输 出unit
是is否
与室
内机
outdoor
equal
to the
capacity demand of indoor
能 力 需units?
求相同?
No
否
内外机
拨 码 and outdoor unit
Refer参
to照
the室dial-up
of indoor
是
Yes
检查室内
Check if the indoor
机电
子膨胀
阀动作
是否
electronic
expansion
valve
can 正
work
常normally
?
否
No
使阀体
线圈
啮合
Engage
the和
valve
body
with the coil
Yes
是
检查室内外
Check if the indoor / outdoor
机过
滤网
或 换 热fins
翅are
片是
filters
or radiating
dirty
blocked?
否
有or脏
堵?
否No
统 管 pipe
路 有is堵
塞
The系
system
blocked
Yes
是
参 to
照the
维修
和 保and
养 Maintenance
Refer
Repair
Focus
on查
checking
and
connection
indoor
units
and
主要检
各 室 内the
机inlet
与主
管outlet
连 接 of
的the
进出
口 , 还 between
有室内、
外机
的电
子main
pipe. Also focus on checking the electronic expansion valve of indoor unit and outdoor
膨
胀
阀
等
处
。
更
换
电
子
膨
胀
阀
、
干
燥
过
滤
器
等
零
部
件
unit. Replace the electronic expansion valve, drying filter and other parts
209
DIGITAL MULTI VRF
MAINTENANCE
3) Exhaust Temperature Protection
Exhaust排气温度保护
Temperature Protection
测量压缩机
Measure if the exhaust
排气温度是否已到
temperature
of compressor
reaches
130℃?
130℃?
No
否
No
否
正确?
是
Yes
Yes
是
检查当压缩机
When the exhaust
排气温度高于115℃时,
temperature of compressor is
higher than 115℃, check if the
其相应液旁通插头是否接
corresponding liquid bypass
plug is connected
通? through?
Measure测量
if the resistance
of temperature sensor is
感温包阻值是否
correct?
No
否
Replace更换室外机主板
the mainboard of outdoor
unit
Replace
the corresponding exhaust
更换相应排气感温包
temperature sensor
是Yes
检查相应
Check if the corresponding liquid
bypass sub-assembly is in good
液旁通组件是否良好,如
condition, e.g. if the solenoid
电磁阀是否完好,毛细管
valve is in good condition and if
the capillary pipe is blocked?
是否堵塞?
No
否
更换液旁通组件
Replace
the liquid bypass sub-assembly
是Yes
Check
if the capacity
检查室外机
output of outdoor unit is
容量输出是否与室内机能力
equal to the capacity
demand
of indoor units?
需求相同?
No
否
Refer to
the dial-up of indoor and outdoor unit
参照室内外机拨码
Yes
是
系统管路出现泄漏,进行补
Repair
the leakage of system pipe and
add漏,并按原质量添加制冷剂。
refrigerant according to the required
volume
210
DIGITAL MULTI VRF
MAINTENANCE
4) Compressor overcurrent protection
Abnormal
overcurrent error
异常过电流故障
压缩机接线
是否正确
If the compressor wiring
is correct
No
否
Adjust
the compressor wiring
调整压缩机接线
Yes
是
电流值是否高
于保护器设定值
If the current value is
higher than the preset
value of protector
No
否
Replace
the overcurrent protector
更换过流保护器
Yes
是
If the high voltage of unit
is normal
机组高压是否正常
No
否
Refer参照高压保护
to high voltage protection
Yes
是
If the voltage is normal
电压是否正常
否No
Contact联系供电公司
the power supply company
Yes
是
通讯恢复正常
The communication
resumes to normal
211
DIGITAL MULTI VRF
MAINTENANCE
5) Communication error
Communication
通讯故障error
检查
Check if the
communication line of
室内机通讯线连接是否
indoor unit is connected
正确?
否
No
确认插头与插口的
方位
Check the orientation of plug and socket
Yes
是
测量
Measure if the
communication
line is
通讯线是否为
through?
No
否
Replace
the communication line
更换通讯线
通路?
Yes
是
检查室内
Check if the communication
外机连接的通讯线连接
line of indoor and outdoor
unit is connected correctly?
是否正确?
否
No
确认插头与插口的
方位
Check the orientation of plug and socket
Yes
是
检查通讯
Check if the two ends of
线两端是否分别套有
communication line are
mounted with magnetic ring?
磁环?
否
No
请缠绕上随机配套
的磁环
Please mount the included magnetic ring
是
Yes
查看所
Check if the outdoor unit
is electrically powered?
连室外机是否已
供电?
否
No
请给室外机接通电
源
Please supply power to the outdoor unit
Yes
是
同系统
If the address codes of
indoor units in the same
中的室内机地址码是否
system are repeated?
有重复?
否
No
修改相关重复的地
址码
Change the repeated address codes
Yes
是
线控器地址
If the address code of wired
码和所连的室内机地址
controller complies with the
address code of the connected
码是否相符?
indoor unit?
No
否
修改线控器地址码
Change
the address code of wired controller
212
DIGITAL MULTI VRF
MAINTENANCE
6) Water-full protection
故障显示
Fault
display
检查是否有水溢
Check if the water
overflows?
出?
No
否
If the voltage of liquid
液位开关端子的
level switch terminal
电压是否正确?
is correct?
Yes
是
否
No
Replace
the mainboard of indoor unit
更换室内机主板
Yes
是
No
否
If the drainage pump is
排水泵是否运转?
running?
If the voltage of
排水泵端子的电
drainage pump
压是否正确?
terminal is correct?
Yes
是
检查液位开关
Check
the liquid level switch
否
No
Yes
是
If the drainage pipe is
排水管是否疏通?
unblocked and if the
water
flow is smooth?
流水是否顺畅?
No
否
Replace
the mainboard of indoor unit
更换室内机主板
Check检查排水泵配线
the wiring of drainage pump
Adjust
the drainage pipe
调整排水管
Yes
是
Check检查排水泵
the drainage pump
7) Temperature sensor error
Temperature
sensor error
感温包故障
感温包插头
If the plug on temperature
与主板上的插口连接
sensor is correctly connected
to the socket on mainboard?
是否正确?
否
No
确认插口插头的方位
Check
the orientation of plug and socket
Yes
是
拆下感温
Remove the temperature and
measure if its resistance is
包,测量其阻值是否在正
within normal range?
常范围内?
No
否
Replace the temperature sensor
更换感温包
Yes
是
更换室内机主板
Replace
the mainboard of indoor unit
8) Pressure sensor error
Pressure sensor error
Check if the plug of high
pressure sensor is correctly
connected to the socket?
No
Check the orientation of plug and
socket
Yes
Measure if the output value
(DC voltage) of the outdoor
mainboard socket is
normal?
Yes
Replace the high pressure sensor
No
Replace the mainboard of outdoor unit
213
DIGITAL MULTI VRF
MAINTENANCE
3 WIRING DIADRAM
GMVL-R120W/Na-K
GMV-R120W/Na-K
214
DIGITAL MULTI VRF
MAINTENANCE
GMV-R160W/Na-M
GMVL-R260W2/Na-M,GMVL-R300W2/Na-M
FUSE
FUSE
U
V W
M
215
DIGITAL MULTI VRF
MAINTENANCE
GMV-R260W2/Na-M,GMV-R300W2/Na-M
FUSE
'
'
FUSE
' '
U
V W
M
GMVL-R450W3/Na-M
216
DIGITAL MULTI VRF
MAINTENANCE
GMV-R450W3/Na-M,GMVT3-R420W3/B-M
GMVL-R560W4/Na-M,GMVL-R600W4/Na-M
L
L
H
L
ote
217
DIGITAL MULTI VRF
MAINTENANCE
GMV-R560W4/Na-M,GMV-R600W4/Na-M
L
L
GMVL-R900W6/Na-M
218
DIGITAL MULTI VRF
MAINTENANCE
GMV-R900W6/Na-M
219
DIGITAL MULTI VRF
MAINTENANCE
Indoor unit
Indoor Unit Circuit Diagram
GMV-R22P/Na-K, GMV-R25P/Na-K, GMV-R28P/Na-K, GMV-R36P/Na-K, GMVL-R22P/Na-K,
GMVL-R25P/Na-K, GMVL-R28P/Na-K, GMVL-R36P/Na-K
GMV-R45P/Na-K , GMV-R50P/Na-K, GMVL-R45P/Na-K GMVL-R50P/Na-K,
220
DIGITAL MULTI VRF
GMV-R56P/Na-K, GMV-R71P/Na-K,
GMVL-R80P/Na-K
MAINTENANCE
GMV-R80P/Na-K,
GMVL-R56P/Na-K,
GMVL-R71P/Na-K,
GMV-R90P/Na-K, GMV-R112P/Na-K, GMV-R140P/Na-K, GMVL-R90P/Na-K, GMVL-R112P/Na-K,
GMVL-R140P/Na-K
221
DIGITAL MULTI VRF
MAINTENANCE
GMV-R125P/Na-K, GMVL-R125P/Na-K
GMV-R22P/NaB-K, GMV-R28P/NaB-K, GMV-R36P/NaB-K, GMV-R45P/NaB-K, GMV-R56P/NaB-K,
GMV-R71P/NaB-K,
63624640
222
DIGITAL MULTI VRF
MAINTENANCE
GMV-R22PS/NaB-K, GMV-R28PS/NaB-K, GMV-R36PS/NaB-K, GMV-R45PS/NaB-K,
GMV-R56PS/NaB-K, GMV-R71PS/NaB-K
GMV-R90P/NaB-K, GMV-R112P/NaB-K, GMV-R140P/NaB-K
C1
C2
223
DIGITAL MULTI VRF
MAINTENANCE
GMV-R90PS/NaB-K, GMV-R112PS/NaB-K, GMV-R140PS/NaB-K
C1
C2
GMV-R28T/Na-K, GMV-R36T/Na-K, GMV-R45T/Na-K, GMV-R50T/Na-K, GMV-R56T/Na-K,
GMV-R71T/Na-K, GMV-R90T/Na-K, GMV-R112T/Na-K, GMV-R125T/Na-K, GMVL-R28T/Na-K,
GMVL-R36T/Na-K, GMVL-R45T/Na-K, GMVL-R50T/Na-K, GMVL-R56T/Na-K, GMVL-R71T/Na-K,
GMVL-R90T/Na-K, GMVL-R112T/Na-K, GMVL-R125T/Na-K
Limit Switch
Swing Motor
Water Level Switch
Environment
1
2
3
Manual Panel
4
Temp.sensor
Out
Temp.sensor
Mid
Temp.sensor
In
Temp.sensor
224
DIGITAL MULTI VRF
MAINTENANCE
GMV-R22T/NaA-K、GMV-R28T/NaA-K、GMV-R36T/NaA-K、GMV-R45T/NaA-K
GMV-R22Td/Na-K,GMV-R28Td/Na-K,GMV-R36Td/Na-K
225
DIGITAL MULTI VRF
MAINTENANCE
GMV-R22G/NaB-K, GMVL-R22G/NaB-K, GMV-R28G/NaB-K, GMVL-R28G/NaB-K,
GMV-R36G/NaB-K, GMVL-R36G/NaB-K, GMV-R45G/NaB-K, GMVL-R45G/NaB-K
GMV-R50G/NaB-K, GMV-R56G/NaB-K, GMVL-R50G/NaB-K, GMVL-R56G/NaB-K
226
DIGITAL MULTI VRF
MAINTENANCE
GMV-R22G/NaC-K, GMV-R28G/NaC-K , GMV-R36G/NaC-K, GMV-R45G/NaC-K,
GMVL-R22G/NaC-K, GMVL-R28G/NaC-K , GMVL-R36G/NaC-K, GMVL-R45G/NaC-K
GMV-R71G/Na-K, GMV-R80G/Na-K, GMVL-R71G/Na-K, GMVL-R80G/Na-K
227
DIGITAL MULTI VRF
MAINTENANCE
GMV(L)-R22G/NaG-K、GMV(L)-R28G/NaG-K、GMV(L)-R36G/NaG-K、GMV(L)-R45G/NaG-K、
GMV(L)-R50G/NaG-K、GMV(L)-R56G/NaG-K、GMV(L)-R63G/NaG-K、GMV(L)-R71G/NaG-K
GMV-R28Zd/Na-K, GMV-R36Zd/Na-K, GMV-R50Zd/Na-K, GMV-R71Zd/Na-K, GMV-R90Zd/Na-K,
GMV-R112Zd/Na-K, GMV-R125Zd/Na-K, GMVL-R28Zd/Na-K, GMVL-R36Zd/Na-K,
GMVL-R50Zd/Na-K, GMVL-R71Zd/Na-K, GMVL-R90Zd/Na-K, GMVL-R112Zd/Na-K,
GMVL-R125Zd/Na-K
228
DIGITAL MULTI VRF
MAINTENANCE
GMV-R71Zd/NaB-K, GMV-R90Zd/NaB-K, GMV-R112Zd/NaB-K, GMV-R125Zd/NaB-K,
229
DIGITAL MULTI VRF
MAINTENANCE
4 DISASSEMBLY AND ASSEMBLY PROCEDURE OF MAIN PARTS
4.1Outdoor Unit
Disassembly and Assembly of external casing
Remark :
Step
Illustration
Handling Instruction
1. Remove the front panel
①Use screwdriver to
remove the screws;
②Raise upward and
remove the front panel.
2. Remove the electric box cover
① Use screwdriver to
remove the screws;
② Remove the electric
box cover
3. Remove the electric box
①Unplug the power
cords
and
communication
lines
from the mainboard;
②Use screwdriver to
remove the screws;
③ Remove the electric
box
230
DIGITAL MULTI VRF
MAINTENANCE
4. Remove the flow-guide cover
①Use screwdriver to
remove the screws;
②Remove
the
flow-guide cover
5. Remove the fan sub-assembly
①Use screwdriver to
remove the screws;
②Remove
the
fan
sub-assembly
6. Remove the front panel 1 and front
lining plate sub-assembly
①Use screwdriver to
remove the screws;
②Remove the front
panel 1
③Use screwdriver to
remove the screws;
④Remove the front
lining plate sub-assembly
7 Remove the left side plate, right
side plate, rear lining plate
sub-assembly and back cover board
①Use screwdriver to
remove the screws fixing
the left side plate and
right side plate;
②Remove the left side
plate and right side plate
③Use screwdriver to
remove the screws fixing
the rear lining plate
sub-assembly and back
cover board;
④Remove the rear lining
plate sub-assembly and
back cover board
231
DIGITAL MULTI VRF
8. Assemble the unit in reverse
procedures
MAINTENANCE
●Assemble the unit in
reverse
to
the
disassembly procedures
and energize it for
testing.
232
DIGITAL MULTI VRF
MAINTENANCE
Removal and Installation of Compressor
Remark: Before removing the compressor, make sure that there is no refrigerant inside the pipe system and that the power
has been cut off.
Step
1. Remove the power cord
2. Remove the oil separator,
oil separator support and pipe
in front of the compressor
3. Remove the compressor
from chassis
4. Fix the new compressor to
chassis
Illustration
Handling Instruction
Mark the power
cable colors and
corresponding
terminal codes
during removal.
①Use screwdriver to loosen the
screws fixing the power cable.
② Pull out the power cable.
Note: When removing the power
cable, please mark the power cable
color and corresponding terminal,
thus to avoid error during
reinstallation.
①Disconnect the pipeline from the
compressor and oil separator.
②Use screwdriver to remove the
screws fixing the oil separator
support
③ Remove the oil separator, oil
separator support and related pipes
①. Use tool to remove the bolts
fixing the compressor
②Remove the compressor from
chassis
①. Install the compressor correctly to
the chassis sub-assembly.
②Tighten the nuts with tool.
233
DIGITAL MULTI VRF
5. Connect the suction and
exhaust pipe of compressor to
system pipeline
MAINTENANCE
①. Weld pipeline connected to the
compressor (including the exhaust
pipe, suction pipe, oil balance pipe
and gas balance pipe).
6. Connect the power cables
of compressor correctly
7. Reinstall the electric heater
and exhaust sensor of the
compressor.
8. Check if the compressor
rotates in correct direction if
the lubricating oil is leaked.
234
DIGITAL MULTI VRF
MAINTENANCE
Disassembly and Assembly of 4-way valve
Step
Illustration
Handling Instruction
1. Remove the coil of 4-way
valve
①Use screwdriver to remove the
screws fixing the coil
②Remove the coil of 4-way valve.
2. Use welding gun to cut the
four pipes connected to 4-way
valve.
①. Use welding gun to cut the pipes
connected to 4-way valve (weld spot
indicated in the figure)
3. Remove the 4-way valve
①. Remove the 4-way valve
4. Replace the 4-way valve
①Put the new 4-way valve to correct
position
5.
Reinstall
the
pipes
connected to 4-way valve.
①. Reweld the pipes connected to
4-way valve
6. Install the coil of 4-way
valve
①. Place the coil of 4-way valve
correctly.
②Tighten
the
screws
with
235
DIGITAL MULTI VRF
MAINTENANCE
screwdriver.
Removal and Installation of Electronic Expansion Valve
Remark :
Step
Illustration
Handling Instruction
1. Remove the coil of
electronic expansion valve
①Rotate the coil of electronic
expansion valve and remove it after
loosening the clamp.
2. Use welding gun to cut the
pipes connected to electronic
expansion valve
①. Use welding gun to cut the pipes
connected to electronic expansion
valve
3. Replace the
expansion valve.
electronic
Cut the two welds
here by welding
①Put the new electronic expansion
valve to correct position
236
DIGITAL MULTI VRF
MAINTENANCE
4.
Reinstall
the
pipes
connected
to
electronic
expansion valve.
①. Reweld the pipes connected to
electronic expansion valve
5. Install the coil of electronic
expansion valve
①. Mount the coil of electronic
expansion valve onto valve body and
align the clamp.
237
DIGITAL MULTI VRF
MAINTENANCE
Removal and Assembly of Fan
Remark :
Step
Illustration
Handling Instruction
1. Remove the front panel
①Use screwdriver to remove the
screws;
②Remove the front panel;
2. Remove the electric box
cover
①Use screwdriver to remove the
screws;
②Remove the electric box cover
3. Remove the power cord of
fan
①Unplug the power cord of fan
from mainboard;
②Remove the power cord from the
strap and cable hook
4. Remove the flow-guide
cover
①Use screwdriver to remove the
screws;
②Remove the flow-guide cover
238
DIGITAL MULTI VRF
MAINTENANCE
5. Remove the axial flow fan
①Remove the lower nuts;
②Remove the axial flow fan
6. Remove the motor
①Use screwdriver and spanner to
remove the lower bolts;
②Remove the motor
7. Replace the motor and
reassemble the unit.
①Assemble the unit in reverse to
the disassembly procedures and
energize it for testing.
239
DIGITAL MULTI VRF
MAINTENANCE
Removal and Installation of Electric Box
Remark :
Step
Illustration
Handling Instruction
1. Remove the electric box
cover
①Use screwdriver to remove the
screws;
②Remove the electric box cover
2. Remove the electric box
①Unplug the power cords and
communication lines from the
mainboard;
②Use screwdriver to remove the
screws;
③ Remove the electric box
3. Assemble in reverse to the
disassembly procedures.
①Assemble the unit in reverse to the
disassembly procedures and energize
it for testing.
240
DIGITAL MULTI VRF
MAINTENANCE
Removal and Installation of Gas-Liquid Separator
Remark :
Step
1. Disconnect the pipes
connected to the gas-liquid
separator
2. Remove the gas-liquid
separator from the chassis
3. Fix the new gas-liquid
separator onto chassis
Illustration
Handling Instruction
①. Disconnect the pipes connected to
the gas-liquid separator
①. Use tool to remove the bolts
fixing the gas-liquid separator
②Remove the gas-liquid separator
from the chassis
①. Install the gas-liquid separator
correctly to chassis sub-assembly.
②Tighten the bolts with tool.
241
DIGITAL MULTI VRF
MAINTENANCE
4.2 Indoor Unit
1) Common Duct-type Unit
Removal and Assembly of Fan Motor
Remarks: Before removing the fan, make sure to cut off the power firstly.
Step
1. Unplug
cables
the
Illustration
Handling Instruction
motor
●Cut off the power supply
of indoor unit. Use
screwdriver to remove the
electric box cover and
unplug the motor cables in
electric box.
2. Remove the air inlet
cover board
●Use
screwdriver
to
remove the lower air inlet
cover board
3. Remove the
propeller housing
back
●Loosen
the
clamp
between back propeller
housing and front propeller
housing. Remove the back
propeller housing
4. Remove the
propeller housing
front
●Use
screwdriver
to
loosen the screws fixing
the front propeller housing.
Remove the front propeller
housing.
5. Loosen the fan and
motor.
●Use inner hexagonal
spanner to loosen the
screws on fan and remove
the clamp fixing the motor.
6. Remove the motor
●Firstly, disengage the
motor from motor support
and then disengage the fan
from the motor. Then,
remove the motor from the
lower air inlet frame. In
which, for the motor with
automatic motor support,
the motor support shall be
removed in advance and
then changed to the unit.
●Assemble the unit in
reverse to the disassembly
procedures and energize it
for testing.
7. Replace with a new
motor
242
DIGITAL MULTI VRF
z
MAINTENANCE
Duct-Type Unit(5.6 kW~8.0 kW)
Removal and Assembly of Fan Motor
Remarks: Before removing the fan, make sure to cut off the power firstly.
Step
Illustration
Handling Instruction
1. Unplug the motor
cables
●Cut off the power
supply of indoor unit. Use
screwdriver to remove the
electric box cover and
unplug the motor cables
in electric box.
2. Remove the filter
sub-assembly and air
inlet cover board
●Remove
the
filter
sub-assembly from the air
inlet frame and use
screwdriver to remove the
air inlet cover board.。
3. Remove the screws on
fan sub-assembly.
●Remove the screws on
fan sub-assembly.
4. Overturn the propeller
housing
●Rotate the propeller
housing to the air inlet
opening according to
arrow direction.
5. Loosen the fan and
motor.
●Use inner hexagonal
spanner to loosen the
screws on fan and remove
the clamp fixing the
motor.
243
DIGITAL MULTI VRF
6. Replace the motor
7. Assemble the unit in
reverse
to
the
disassembly procedures
MAINTENANCE
●Firstly, disengage the
motor
from
motor
support.
Then,
sequentially
disengage
the fan sub-assembly
form the motor shaft.
Remove the motor from
the air inlet and replace
with new motor. In
which, for the motor with
automatic motor support,
the motor support shall be
removed in advance and
then changed to the unit.
●Assemble the unit in
reverse
to
the
disassembly procedures
and energize it for testing.
244
DIGITAL MULTI VRF
z
MAINTENANCE
Duct-Type Unit(9.0 kW~14 kW)
Removal and Assembly of Fan Motor
Remarks: Before removing the fan, make sure to cut off the power firstly.
Step
Illustration
1. Unplug the
motor cables
Handling Instruction
●Cut off the power supply
of indoor unit. Use
screwdriver to remove the
electric box cover and
unplug the motor cables in
electric box.
2. Remove the
filter
sub-assembly and
air inlet cover
board
●Remove
the
filter
sub-assembly from the air
inlet frame and use
screwdriver to remove the
air inlet cover board.。
3. Remove the
screws on fan
sub-assembly.
●Remove the screws on
fan sub-assembly.
4. Overturn the
propeller housing
●Rotate the propeller
housing to the air inlet
opening according to
arrow direction.
5. Loosen the fan
and motor.
●Use inner hexagonal
spanner to loosen the
screws on fan and remove
the clamp fixing the
motor.
6. Replace the
motor
●Firstly, disengage the
motor from motor support.
Then,
sequentially
disengage
the
fan
sub-assembly form the
motor shaft. Remove the
motor from the air inlet
and replace with new
motor. In which, for the
motor with automatic
motor support, the motor
support shall be removed
in advance and then
changed to the unit.
245
DIGITAL MULTI VRF
MAINTENANCE
●Assemble the unit in
reverse to the disassembly
procedures and energize it
for testing.
7. Assemble the
unit in reverse to
the disassembly
procedures
Cassette-type Unit
Step
Removal and Assembly of Fan Motor
Illustration
Handling Instruction
1. Loosen the screws fixing
the water tray
●Use screwdriver to loosen
the screws fixing the water
tray
2. Remove the water tray
●Remove the water tray
3. Loosen the bolts fixing the
fan
●Use spanner to loosen the
bolts fixing the fan.
4. Remove the fan
●Remove the fan
5. Loosen the screws fixing
the motor
●Use screwdriver to loosen
the screws fixing the motor
246
DIGITAL MULTI VRF
MAINTENANCE
6. Remove the motor and
replace it
●Remove the motor and
replace it
7. Tighten the screws fixing
the motor
●Use screwdriver to tighten
the screws fixing the motor.
8. Mount the fan and tighten
the fixing bolts
●Mount the fan and use
spanner to tighten the bolts
fixing the fan
9. Mount the water tray and
tighten the screws
●Use screwdriver to loosen
the screws fixing the water
tray
247
DIGITAL MULTI VRF
Step
MAINTENANCE
Removal and Installation of Drainage Pump
Illustration
Handling Instruction
1. Loosen the screws fixing
the water tray
●Use screwdriver to loosen
the screws fixing the water
tray
2. Remove the water tray
●Remove the water pump
and replace it.
1.Loosen the water outlet pipe
2.Loosen the screws
fixing the water pump
3. Pull out the water outlet
pipe and loosen the screws
fixing the water pump.
●Pull out the water outlet
pipe and use screwdriver to
loosen the screws fixing
the water pump.
4.Remove the water pump
and replace it.
●Remove the water pump
and replace it.
1.Tighten the drainage pipe
2.Tighten the screws fixing
the drainage pump
5. Connect the drainage pipe
and tighten the screws fixing
the water pump.
●Connect the drainage pipe
and use screwdriver to
tighten the screws fixing
the water pump.
6. Mount the water tray and
tighten the screws
●Use screwdriver to
tighten the screws fixing
the water tray
248
DIGITAL MULTI VRF
MAINTENANCE
1-way Cassette-type Unit
Removal and Assembly of Fan Motor
Step
Illustration
Handling Instruction
1.Remove the
front panel
●Press switch on
both side of the
panle. Open one side
of the panel and
remove the three
opposite
buckles.
Remove the front
panel.
2.Remove the
screw of front
panel
●Loosen the screw
with screwdriver
3.Remove the
panel.
●Remove
panel.
4 . Loosen the
screws fixing
the water tray
●Use screwdriver to
loosen the screws
fixing the water tray
5.Remove the
water tray and
filter support
●Remove the water
tray and filter support
the
249
DIGITAL MULTI VRF
MAINTENANCE
6 . Loosen the
fixing screw of
motor cover
●Loosen the fixing
screw of motor cover
with screwdriver
7.
Remove
motor
cover
subassembly
●Remove
motor
cover subassembly
8. Loosen the
screw
fixing
motor
and
motor shaft
Rotate the cross flow
blade to make the
screw
upward.
Loosen the screw
with screwdriver.
9. Replace the
motor
●Remove the motor
and mount a new one
10. Mount the
motor
cover
subassembly
and tighten the
screw
●Mount the motor
cover subassembly
and tighten the fixing
screw of motor cover
and cross flow blade.
250
DIGITAL MULTI VRF
MAINTENANCE
11 Mount water
tray and filter
support. Fix the
screw.
●Mount water tray
and filter support.
tighten the screw
fixing water tray and
filter support.
12.
Mount
panel
subassembly
and tighten the
screw.
●Mount
panel
subassembly
and
tighten the screw.
13.
Mount
panel
subassembly
●Mount
panel
subassembly
and
press the switch on
both side of the
panel.
Removal and Assembly of Water Pump
Step
1. Remove the
panel
subassembly
Illustration
Handling
Instruction
●Press switch on
both side of the
panle. Open one
side of the panel
and remove the
three
opposite
buckles. Remove
the front panel.
251
DIGITAL MULTI VRF
MAINTENANCE
2. Loosen the
screw
fixing
panel
subassembly
and main body
●Loosen the screw
fixing
panel
subassembly and
main body with
screwdriver
3.Take out the
panel
subassembly
●Take out the
panel subassembly
4 . Loosen the
screw of water
tray
●Loosen the screw
of water tray with
screwdriver
5.Remove the
water tray and
filtering screen
support
●Remove
the
water tray and
filtering
screen
support
6. Loosen the
fixing screw of
water pump
●Loosen the fixing
screw of water
pump
with
screwdriver. Pull
off the drain pipe
from the water
pump.
7. Replace the
water pump
●Remove
the
water pump and
mount a new one.
252
DIGITAL MULTI VRF
MAINTENANCE
8. Connect the
water
pump
and drain pipe.
Tighten
the
fixing screws.
●Connect
the
water pump and
drain pipe. Tighten
the fixing screws.
11. Mount the
water tray and
filtering screen
support
and
tighten
the
screw
●Mount the water
tray and filtering
screen support and
tighten the screw.
12.
Mount
panel
subassembly
and tighten the
screw.
●Mount
panel
subassembly and
tighten the screw.
13.
Mount
panel
subassembly
●Mount
panel
subassembly and
press the switch on
both side of the
panel.。
253
DIGITAL MULTI VRF
MAINTENANCE
3) Wall-mounted type
Removal and Assembly of Fan Motor
Remark:Before removing the compressor, make sure that there is no refrigerant inside the pipe system and that the power
has been cut off.
Step
Illustration
Handling Instruction
1. Firstly,
●Firstly, use screwdriver to
remove
loosen the screws.
the front
●Unplug
the
motor
panel,
terminals in the electric
front case
box. Loosen the earth
and
screws and lift up.
electric
box
2.
Remove
the
evaporator
Screw
3.
Remove
the motor
and cross
flow fan
●Firstly, use screwdriver to
remove the fixing screws
on the left and right side.
Then,
remove
the
evaporator.
●Use
screwdriver
to
remove the screws fixing
the motor clamp and
remove
the
screws
connecting the motor and
cross flow fan. Then, the
motor can be separated
from the cross flow fan.
Screw
254
DIGITAL MULTI VRF
MAINTENANCE
4) Floor ceiling type
Removal of Front Grill Sub-assembly
Before removal, please make sure that the power supply has been cut off. During removal, please protect the
parts properly and do not put the filter close to the source of high-temperature heat.
Step
Illustration
Handling Instruction
●Before
removal,
please make sure that
the power supply has
been cut off. During
removal,
please
protect
the
parts
Removal of Front
properly and do not
Grill
put the filter close to
Sub-assembly
the
source
of
high-temperature
heat.
Removal of Left / Right Decorative Plate
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly. Take special care not to scratch the surface parts
Step
Illustration
Handling Instruction
●Use the screwdriver
to remove the screws
at the shown position.
Then, push upward to
remove the left and
right decorative plate.
(The screws as shown
Removal of Left /
by the arrow)
Right Decorative
Plate
Removal of Front Panel Sub-assembly
Remarks: Use the screwdriver to remove the 8 screws at the positions shown by the arrow (Respectively 2
screws on left and right, and 4 on front). Then, remove the front panel sub-assembly.
Step
Illustration
Handling Instruction
●Use the screwdriver
to remove the 8
screws at the
positions shown by
the arrow
(Respectively 2
screws on left and
Removal of Front
right, and 4 on front).
Panel
Then, remove the
Sub-assembly
front panel
sub-assembly.
255
DIGITAL MULTI VRF
MAINTENANCE
Removal of Electric Box Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly. Take special care to protect the electric elements in the box and prevent them from
water or knock.
Handling
Step
Illustration
Instruction
●Use
the
screwdriver
to
remove the 2
screws as shown
by the arrow on
left. Remove the
electric box cover.
1. Remove the
electric box cover
2. Remove the
electric
box
sub-assembly
●Use
the
screwdriver
to
remove the 2
screws as shown
by the arrow on
left (respectively 2
on two sides).
Then, remove the
electric
box
sub-assembly and
cables.
Removal of Guide Louver Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly. Take special care to protect the joint of guide louver.
Handling
Step
Illustration
Instruction
●Firstly, remove
the guide louver
from the assembly
position on guide
louver
holder.
Then, remove the
two ends from the
position where the
Removal of Guide
guide lover is
Louver
jointed
to
the
Sub-assembly
swing motor. (The
holder assembly
position
is
as
shown by the
arrow and the
jointing position on
swing motor is as
shown by the
circle)
256
DIGITAL MULTI VRF
MAINTENANCE
Removal of Water Tray Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly.
Handling
Step
Illustration
Instruction
●
Use
the
screwdriver
to
remove the 4
screws as shown
(respectively 2 on
left and right side).
Removal of Water
Then, remove the
Tray
water
tray
Sub-assembly
sub-assembly.
Removal of Swing Louver Holder Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly. Take special care to protect the joint of swing louver.
Step
Pictorial view
Operation
instructions
●Firstly, use the
screwdriver
to
remove
the
screws on the two
ends of swing
louver
holder
sub-assembly
Removal of Swing
(respectively 1 on
Louver
Holder
each side). Then,
Sub-assembly
use your hand to
remove the swing
louver
holder
sub-assembly
from the guide
louver holder.
Removal of Evaporator Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
take care to protect the copper tube and aluminum fin of evaporator. The copper tube shall be well sealed if it is
to be removed for a long time.
Handling
Step
Illustration
Instruction
●Use
the
screwdriver
to
remove
the
screws as shown
by
the
arrow.
(There are totally
4
screws,
respectively 2 on
left and right side
Removal
of
of the evaporator.
Evaporator
There
are
2
Sub-assembly
screws on the
evaporator
tube-exit
clamp
sub-assembly).
257
DIGITAL MULTI VRF
MAINTENANCE
Removal of Swing Motor Holder Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly.
Handling
Step
Illustration
Instruction
●Use screwdriver
to remove the
screws as shown
on left.
Removal of Swing
Motor
Holder
Sub-assembly
Removal of Left / Right Side Plate Foam Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly. Take special care to prevent the foam sub-assembly from heating or knock.
Handling
Step
Illustration
Instruction
●Remove the left /
right side plate
foam
sub-assembly in
the direction as
shown on left.
Removal of Left /
Right Side Plate
Foam
Sub-assembly
258
DIGITAL MULTI VRF
MAINTENANCE
Removal of Fan and Motor Sub-assembly
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly and take special care to store the screws fixing the fan
Step
Illustration
Handling Instruction
●Use your hand to press
the clamp of front and
back propeller housing
downward. Then, pull
upward to remove the
front propeller housing.
After that, knock off the
two screws at back
1. Remove the
propeller housing. Then,
front and back
use your hand to hold the
propeller housing
clamp of back propeller
housing and raise upward
to remove the back
propeller housing. (The
clamp is shown by the
arrow, and the screw is
shown by the circle, totally
2 on left and right side).
●Use inner hexagonal
spanner to loosen the
screws fixing the fan.
Then, remove the fan. The
inner hexagonal spanner
and its application position
2. Remove the fan
are as shown by the
arrow.
3. Remove the
mounting plate of
bearing
●Use
screwdriver
to
remove the 4 screws on
the mounting plate of
bearing. (As shown in the
square)
●Use the screwdriver to
loosen the bolts as shown
to remove the motor
clamp and motor holder.
4. Remove
motor
the
259
DIGITAL MULTI VRF
MAINTENANCE
Removal of Left / Right Mounting Plate
Remarks: Before removal, please make sure that the power supply has been cut off. During removal, please
protect the parts properly.
Handling
Step
Illustration
Instruction
●Use the tool to
remove the bolts
fixing the left and
right
mounting
plate.
(The
bolts
Removal of Left /
are as shown by
Right
Mounting
the arrow)
Plate
260
DIGITAL MULTI VRF
MAINTENANCE
5 EXPLODED VIEWS AND PART LIST
5.1 Outdoor Unit
GMV(L)-R120W/Na-K
261
DIGITAL MULTI VRF
MAINTENANCE
List of components
GMV(L)-R160W/Na-M
No.
Part name
Quantity
Material code
1
01394331
1
05014617
1
072287771
1
Electric Box
2
Gas-liquid separate
3
Oil separator
4
panel rear
1
01308736
5
Axial fan
2
10335253
6
Motor
2
150154511
7
Suction pipe
1
03628805
8
Condenser connect-pipe
1
05024613
9
motor support
1
01708733
10
discharge pipe 2
1
03818797
11
4-Way Vavle
1
43000338
12
Out-pipe of uninstall vavle
1
03234632
13
Liquid Valve Assy
1
07130209
14
Gas Valve Assy
1
07103030
15
Exit Tube of condenser
1
03338806
16
High pressure liquid tank
1
07228735
17
Discharge pipe 1
1
03618769
18
Gas Valve connect pipe
1
05028829
19
Chassis
1
01218731
20
Dry Filter
1
07218769
21
PWM valve
1
22
liquid-gas separator
1
07228767
23
In-pipe of uninstall vavle
1
03234649
24
Compressor
1
00100395
25
Gas-disparting set clamp
1
02148768
26
panel front
1
01308733
27
mid.isolation sheet
1
01238763
28
Front Plate
1
01435433
29
Condensing Assy
1
01138782
30
Support
1
01724601
31
Exit Tube of
1
03338808
32
Top plate
1
01258731
33
Electric expand vavle
1
07130364
connect pipe
Assy
Dry Filter
Remark
Component of
compressor
262
DIGITAL MULTI VRF
MAINTENANCE
263
DIGITAL MULTI VRF
MAINTENANCE
List of components
GMV(L)-R260W2/Na-M, GMV(L)-R300W2/Na-M
No.
Part name
Quantity
Material code
1
01394603
1
05014617
1
072287771
1
Electric Box
2
Gas-liquid separate
3
Oil separator
4
panel rear
1
01308736
5
Axial fan
2
10335253
6
Motor
2
150154511
7
Suction pipe
1
03628805
8
Condenser connect-pipe
1
05014622
9
motor support
1
01708733
10
discharge pipe 2
1
03818797
11
4-Way Vavle
1
43000338
12
Out-pipe of uninstall vavle
1
03234632
13
Liquid Valve Assy
1
07130209
14
Gas Valve Assy
1
07130212
15
Exit Tube of condenser
1
03338806
16
High pressure liquid tank
1
07228735
17
Discharge pipe 1
1
03618769
18
Gas Valve connect pipe
1
05014618
19
Chassis
1
01218731
20
Dry Filter
1
07218769
21
PWM valve
1
22
liquid-gas separator
1
07228767
23
In-pipe of uninstall vavle
1
03234649
24
Compressor
1
00100533
25
Gas-disparting set clamp
1
02148768
26
panel front
1
01308733
27
mid.isolation sheet
1
01238763
28
Front Plate
1
01435433
29
Condensing Assy
1
01138786
30
Support
1
01724601
31
Exit Tube of
1
03338808
32
Top plate
1
01258731
33
Electric expand vavle
1
07138801
connect pipe
Assy
(Only for heat pump)
Dry Filter
Remark
Component of
compressor
264
DIGITAL MULTI VRF
MAINTENANCE
265
DIGITAL MULTI VRF
MAINTENANCE
GMV(L)-R260W2/Na-M, GMV(L)-R300W2/Na-M
No.
Part name
List of Componet
Quantity
Material code
1
Beam of base sub-assy2
1
01874618
2
Carling of base sub-assy
2
01778737
3
Underpan Sub-Assy
1
01284602
4
Beam of base sub-assy1
1
01874620
Welded installation girder of compressors
2
01338778
1
00100534
1
00100532
5
6
7
Compressor and its component
ZPD72KCE-TFD-433
Compressor and its component
ZP67KCE-TFD-420
8
Electric expansion valve component
1
07138834
9
bracket1
1
01804601
10
Component of vent-pipe
1
4300460301
11
4-way valve sub-assy (Only for heat pump)
1
04144603
12
Front plate sub-assy
1
01538734
13
Cover of electric box
1
01414309
14
Triangle support
2
01794701
15
Gas-liquid separator
1
07228768
16
Bi-flow filter drier
1
07218769
17
Double direction liquid accumlator
1
07228765
18
Condenser sub-assy
1
01138785
19
Rear isolation sheet
1
01238740
20
Left side plate sub-assy
1
01314301P
21
Rear cover plate
1
01258737
22
Collect Gas Pipe Sub-assy
1
05024691
23
Stream lined dome
1
22265801
24
Fan
1
10355801
25
Motor
1
15704601
26
Motor fix support
2
01335801
27
Electric box sub-assy
1
01394671P
27
Front plate
1
01538736
29
Right side plate
1
01318759
Remarks
266
DIGITAL MULTI VRF
MAINTENANCE
GMV(L)-R450W3/Na-M,GMV(L)-R560W4/Na-M , GMV(L)-R620W4/Na-M
267
DIGITAL MULTI VRF
MAINTENANCE
List of components
No.
Part name
Quantity
Material code
1
condensor component(Left)
1
1154605
2
Motor
2
15704601
3
Filter
2
7210032
4
Gas-liquid Separator
1
7228781
5
Fan
2
10355801
6
Dry Filter
1
7218769
7
Saparator
2
72200081
8
Discharge Pipe
2
4654632
9
Stream lined dome
2
22265801
10
Bracket (filter)
2
1728795
11
Rear isolation sheet
2
1238740
12
condensor component(Right)
1
1154606
13
Four-way valve
1
43000412
14
Filter
1
7218603
15
Electric Box 1
1
1418788
16
Right Side Plate
1
1308775
17
components of compressor(right)
1
234602
18
electromagnetic valve
6
43000054
19
Support Shelf 2
2
1798775
20
Support Shelf 3
1
1798779
21
Panel 2 (front)
1
1538804
22
Support Shelf 4
2
1798779
23
Support Shelf 1
1
1798773
24
Install Girder by Joint
1
1338739
25
Welding for Support
2
1728802
26
panel1 (front)
1
1538802
27
Electric Box Components1
1
1394684
28
Base
1
1208802
29
Components of compressor(left)
1
234603
30
Liquid Valve Assy 5/8
1
7130128
31
Left Side Plate
1
1308773
32
Liquid Valve Assy 1-1/8
1
7138799
33
Oil Separator
3
7228742
34
Underpan
1
1208784
35
Bidirection Accumulator
1
7228780
36
condensor component(Left)
1
1154605
37
One-way Valve
2
4324001
38
Motor fix support
4
1335801
39
Electric expand vavle
2
7130364
Remark
268
DIGITAL MULTI VRF
MAINTENANCE
GMV(L)-R860W6/Na-M , GMV(L)-R900W6/Na-M
269
DIGITAL MULTI VRF
MAINTENANCE
List of components
No.
Part name
Quantity
Material code
1
Left Side Plate
1
1314602
2
Electric Box Components(left)
1
1394906
3
Mainboard WZS801
1
30228002
4
Mainboard WZ6535U
1
30226194
5
Three-bit Terminal BoardA
1
42011113
6
7
Overcurrent protector HD-13.2-22/UO-10-13
AC Contactor GC3-22/11KK
1
1
46020112
44010236
8
Single-phase Air Switch (4WAY)
1
45020203
9
Overcurrent
QF1/C65N
1
45020203
10
Transformer 48X26G
1
43110233
11
Rear panel
1
01544104P
12
Gas equilibrium tube sub-assy2
1
6114112
13
Discharge Tube Sub-Assy2
1
4634127
14
Inhalation Tube Sub-Assy 2
1
4674121
15
Inhalation Tube Sub-Assy 4
1
4674126
16
Condensor component (left)
1
1124306
17
Saparation component
1
441410301
18
注氟嘴(R410A)
1
61200101
19
Collect Gas Pipe Sub-assy
1
4674122
20
Liquid by-pass sub-assy4
1
4324208
21
Liquid by-pass sub-assy5
1
4324209
22
Liquid by-pass sub-assy6
1
4324210
23
Electromagnetic valve FDF2A
3
43000054
24
Electromagnetic valve componnet
3
4304000602
25
Motor fix support
2
1335801
26
Fan(black)
2
10355801
27
Motor SWB800A
2
15704602
28
Gas by-pass valve sub-assy
1
7334135
29
Electromagnetic valve FDF2A
1
43000054
30
Electromagnetic valve component
1
4304000618
31
Accumulator outlet sub-assy
1
4324450
32
Cooling pipe 1
1
4324217
33
Cooling pipe 2
1
4324218
34
Bidirection Accumulator
1
7228780
35
Accumulator outlet sub-assy
1
4324450
36
Air Collection Pipe Sub-assy
1
463417601
37
Sensor(high pressure)
1
32210103
38
Front lining board sub-assy
2
01264111P
39
Condenser cover1
1
01264108P
40
Rear lining board sub-assy
2
01264113P
41
Crossbeam1
1
01874130P
breaker
(3/40A)
C45N.6A
Remarks
270
DIGITAL MULTI VRF
No
MAINTENANCE
Name
Qty
Material Code
1
01264109P
42
Condenser Cover 2
43
Top cover plate
4
01264110P
44
Stream lined dome(grey)
2
22265801
45
Crossbeam2
1
01874131P
46
Rear isolation sheet
4
22414101
47
Rear Column
2
01854102P
48
Rear Column1
1
1854102
49
Condenser Cover 3
1
01264137P
50
Condenser Cover 4
1
01264138P
51
4-way Valve Sub-Assys
1
4144133
52
Filer Φ19
1
7210037
53
ball valve 1-3/8(R410A)
1
7380010
54
Middle column
1
01854106P
55
Condeser assy(right)
1
1124305
56
Collect Gas Pipe Sub-assy
1
4674122
57
Seperator component
1
441410301
58
注氟嘴(R410A)
1
61200101
59
1
1314604
1
1394907
61
Right side plate
Electric Box Components (right)
GMV-R900W6/Na-N1
mainboard WZS801
1
30228002
62
mainboard1 WZ6535N
1
30226195
63
Three-bit Terminal BoardA
Overcurrent
HD-13.2-22/UO-10-13
AC Contactor GC3-22/11KK
1
42011113
1
46020112
1
44010236
1
45020203
60
64
65
66
protector
1
45020203
68
Single-phase Air Switch
Overcurrent breaker (3/40A) C45N.6A
QF1/C65N
Transformer 48X26G
1
43110233
69
Gas equilibrium tube sub-assy1
1
6114111
70
Electric expand vavle fixed support
1
1804118
71
Cooling Coil 2
1
4324233
72
Oil Separator sub-assy2
6
4324200
73
Oil Separator
1
7424105
74
Filter Φ16
1
7210031
75
Oil Separator fixed support
1
1804119
76
Inhalation Tube Sub-Assy 1
1
4674120
77
Inhalation Tube Sub-Assy 3
1
4674127
78
Gas Separator outlet sub-assy
1
432422301
79
sensor(low pressure)
1
32210100
80
Discharge Tube Sub-Assy1
1
4634126
81
Liquid by-pass sub-assy1
1
4324205
82
electromagnetic valve FDF2A
1
43000054
83
electromagnetic valve components
1
4304000610
84
Liquid by-pass sub-assy2
1
4324206
67
Remarks
Not available in
cooling only unit
271
DIGITAL MULTI VRF
No
MAINTENANCE
Qty
Material code
Electromagnetic valve FDF2A
1
43000054
86
Electromagnetic valvecomponent
1
4304000610
87
Liquid by-pass sub-assy3
1
4324207
88
Electromagnetic valve FDF2A
1
43000054
89
Electromagnetic valve component
1
4304000605
90
Gas-liquid Separator
2
7424103
91
Connecting pipe1(Gas-liquid Separator)
1
5024223
92
Connecting pipe2(Gas-liquid Separator)
1
5024224
93
Steam Inlet Pipe2
1
4324222
94
Oil Balance Tube Assy 1
1
6114107
95
1
6114109
1
100534
5
100532
98
Oil Balance Tube Assy 2
Compressor and fittings
ZPD72KCE-TFD-433
Compressor and fittings
ZP67KCE-TFD-420
Installation Accessory
4
01874107P
99
Liquid Valve Assy 3/4
1
7334103
100
L pipe
2
5020310
101
L pipe
2
5020310
102
Front vertical prop sub-assy
2
01854103P
103
Base Plate Assy 1
1
01194106P
104
Front vertical prop sub-assy
1
01854103P
105
underpan component 2
1
01194108P
106
Reinforced bar assy
1
01874121P
107
Beam of base sub-assy 1
1
01874117P
108
Carling of base sub-assy1
1
01874126P
109
Beam of base sub-assy 2
1
01874118P
110
Beam of base sub-assy 3
1
01874119P
111
Carling of base sub-assy2
1
01874127P
112
Beam of base sub-assy 4
1
01874120P
113
Front panel
2
01544103P
114
panel1
1
01544101P
115
panel3
1
01544110P
116
panel2
1
0154410901P
85
96
97
Name
117
Tube-exit Plate 1
1
02224104P
118
Tube-exit Plate 2
1
0222410501P
119
4-way Valve Sub-Assy
1
4300040032
Remarks
Not available
in cooling
only unit
272
DIGITAL MULTI VRF
MAINTENANCE
5.2 Exploded View of Indoor Unit and List of Component
5.2 .1 Duct type indoor unit
(1)GMV(L)-R22P/Na-K,GMV(L)-R25P/Na-K,GMV(L)-R28P/Na-K,GMV(L)-R32P/Na-K,GMV(L)-R
36P/Na-K
273
DIGITAL MULTI VRF
MAINTENANCE
List of components
No.
Part Name
GMV(L)-R22P/Na-K,
GMV(L)-R25P/Na-K
GMV(L)-R28P/Na-K,GMV(L)-R
32P/Na-K,GMV(L)-R36P/Na-K
Code
Qty.
Code
Qty.
1
Top Cover Sub-assy
01259052
1
01259052
1
2
Hook
02112446
2
02112446
2
3
Seal of Left Side Plate Sub-assy
01499051
1
01499051
1
4
Seal of Connection Pipe Sub-assy
01499053
1
01499053
1
5
Electric Box
01408739
1
01394605
1
6
Left Side Plate Sub-assy
01308788
1
01308788
1
7
Left Support of Evaporator
01078774
1
01078774
1
8
Liquid-entered Pipe Sub-assy
03334601
1
03338810
1
9
Collect Gas Pipe Sub-assy
01305018
1
04674609
1
10
Evaporator Sub-assy
01038785
1
01038786
1
11
Fan Fixed Plate Sub-assy
01339095
1
01339095
1
12
Centrifugal fan
10319051
1
10319051
1
13
Return air inlet side-board Sub-assy
01499055
1
01499055
1
14
Motor
15019053
1
15019522
1
15
Centrifugal fan
10319051
1
10319051
1
16
Bottom Cover
01259086
1
01259086
1
17
Cover of Air-in
01259056
1
01259056
1
18
Water Tray Assy
01279051
1
01279051
1
19
Right Side Plate Sub-assy
01309055
1
01309055
1
20
Hook
02112446
2
02112446
2
21
Left Support of Evaporator
01079056
1
01079056
1
22
Return air inlet side-board Sub-assy
01498783
1
01498783
1
Assy
274
DIGITAL MULTI VRF
MAINTENANCE
(2)GMV(L)-R40P/Na-K,GMV(L)-R45P/Na-K,GMV(L)-R50P/Na-K
275
DIGITAL MULTI VRF
MAINTENANCE
List of components
No.
GMV(L)-R40P/Na-K,
GMV(L)-R45P/Na-K,
GMV(L)-R50P/Na-K
Part Name
Code
Qty.
1
Top Cover Sub-assy
01259064
1
2
Hook
02112446
2
3
Seal of Connection Pipe 2
01498644
1
4
Seal of Connection Pipe 1
01498604
1
5
Electric Box Assy
01404688
1
6
Left Side Plate Sub-assy
01308668
1
7
Left Support of Evaporator
01078629
1
8
Liquid-entered Pipe Sub-assy
04324601
1
9
Collect Gas Pipe Sub-assy
04674601
1
10
Evaporator Sub-assy
01038623
1
11
Fan Fixed Plate Sub-assy
01339058
1
12
Centrifugal fan
10319051
1
13
Return air inlet Sub-assy
01499061
1
14
Motor FG70B
15018322
1
15
Centrifugal fan
10319051
1
16
Bottom Cover
01258649
1
17
Cover of Air-in
01258650
1
18
Water Tray Sub-assy
01278633
1
19
Right Side Plate Sub-assy
01308670
1
20
Hook
02112446
2
21
Left Support of Evaporator
01078625
1
22
Return air inlet Sub-assy
01498641
1
276
DIGITAL MULTI VRF
MAINTENANCE
(3)GMV(L)-R56P/Na-K,GMV(L)-R63P/Na-K,GMV(L)-R71P/Na-K,GMV(L)-R80P/Na-K
277
DIGITAL MULTI VRF
MAINTENANCE
List of compnents
No.
Part Name
GMV(L)-R56P/Na-K,GMV(L)-R63P/Na-K,
GMV(L)-R71P/Na-K,GMV(L)-R80P/Na-K
Code
Qty.
1
Top Cover Sub-assy
01258652
1
2
Hook
02118504
2
3
Left Side Seal-hole Plate Sub-assy
01308680
1
4
Seal of Connection Pipe
01498610
1
5
Electric Box Assy
01394609
1
6
Left Side Plate Sub-assy
01308676
1
7
Left Support of Evaporator
01078603
1
8
Liquid-entered Pipe Sub-assy
04324603
1
9
Collect Gas Pipe Sub-assy
04674602
1
10
Evaporator Sub-assy
01054601
1
11
Fan Fixed Plate Sub-assy
01338631
1
12
Fan Motor (Left)SYP-200/190J-1
15018603
1
13
Return air inlet side-board Sub-assy
01499074
1
14
Motor FG150B
15018612
1
15
Fan motor (Right)SYP-200/190J-1
15018604
1
16
Bottom Cover
01258612
1
17
Cover of Air-in
01258614
1
18
Water Tray Assy
01278612
1
19
Right Side Plate Sub-assy
01308677
1
20
Hook
02118504
2
21
Left Support of Evaporator
01078604
1
22
Return air inlet Sub-assy
01498612
1
278
DIGITAL MULTI VRF
MAINTENANCE
(4)GMV(L)-R90P/Na-K,GMV(L)-R100P/Na-K,GMV(L)-R112P/Na-K,GMV(L)-R125P/Na-K,GMV(L)-
R140P/Na-K
279
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
GMV(L)-R90P/Na-K, GMV(L)-R100P/Na-K,
GMV(L)-R112P/Na-K, GMV(L)-R125P/Na-K,
GMV(L)-R140P/Na-K
Code
Qty.
1
Top Cover Sub-assy
01258606
1
2
Hook
02118504
2
3
Left Side Seal-hole Plate Sub-assy
01308673
1
4
Seal of Connection Pipe
01498601
1
5
Electric Box Assy
01394602
1
6
Left Side Plate Sub-assy
01308676
1
7
Left Support of Evaporator
01078603
1
8
Liquid-entered Pipe Sub-assy
03338802
1
9
Collect Gas Pipe Sub-assy
04674608
1
10
Evaporator Sub-assy
01038624
1
11
Fan Fixed Plate Sub-assy
01338630
1
12
Motor FG75B
15018613
1
13
Fan Motor (Left)SYP-200/190J-1
15018603
2
14
Return air inlet side-board Sub-assy
01499066
1
15
Motor FG150B
15018612
1
16
Fan motor (Right)SYP-200/190J-1
15018604
1
17
Bottom Cover Assy
01258603
1
18
Cover of Air-in
01258602
1
19
Water Tray Assy
01278603
1
20
Right Side Plate Sub-assy
01308677
1
21
Hook
02118504
2
22
Left Support of Evaporator
01078604
1
23
Return air inlet Sub-assy
01498608
1
280
DIGITAL MULTI VRF
MAINTENANCE
(5)GMV ( L ) -R22P/NaB-K, GMV ( L ) -R22PS/NaB-K, GMV ( L ) -R28P/NaB-K, GMV ( L )
-R28PS/NaB-K, GMV(L)-R36P/NaB-K, GMV(L)-R36PS/NaB-K, GMV(L)-R45P/NaB-K, GMV
(L)-R45PS/NaB-K, GMV(L)-R56P/NaB-K, GMV(L)-R56PS/NaB-K, GMV(L)-R71P/NaB-K,
GMV(L)-R71PS/NaB-K
281
DIGITAL MULTI VRF
MAINTENANCE
List of components
No Name
Material Code
Qty
GMVL-R22P/NaB-K
GMVL-R28P/NaB-K
GMVL-R36P/NaB-K
1 Side Plate of Air outlet
01494118
1
1
1
2 Left Support of Evaporator
01094122
1
1
1
01024231
01024230
01024232
1
3 Evaporator Sub-assy
4 Electric expand valve fitting
43040001
1
1
1
5 Right Support of Evaporator
01094121
1
1
1
6 Left Side Plate Sub-assy
01314172
1
1
1
01494115
1
1
1
01494116
1
1
1
9 Hook
02112446
4
4
4
10 Electric Box Cover
01424319
1
1
11 Top Cover Board Assy
01264176
1
1
1
12 Right Side Plate Sub-assy
01314175
1
1
1
0170905801
1
1
1
1570520103
1
1
1
Seal of left side Plate
Sub-assy
Seal of left Connection Pipe
8
Sub-assy
7
13 Motor Support
14 Fan Motor
15 Motor Sub-assy
1
1
1570520201
150024011
1
1
1
02225234
1
1
1
17 Filter
11725202
1
1
1
18 Electric Box
01394994
1
1
1
19 Lower Cover Plate Sub-assy
01264178
1
1
1
Fan motor mounting Plate
20
Sub-assy
01324341
1
1
1
21 Water Pump Assy
15404117
0
0
0
22 Terminal Border
42011106
1
1
1
23 Capacitor
33010027
1
1
1
24 Transformer
43110237
1
1
1
25 Main Bord
30226167
1
1
1
4001039509
1
1
1
27 Display Bord
30296013
1
1
1
28 Sensor sub-assy
39008026
1
1
1
16
Border Plate Assy of Air
Return End
26 Connecting Wire
282
DIGITAL MULTI VRF
MAINTENANCE
Qty
No
Name
Material Code
GMVL-R22PS/Na GMVL-R28PS/Na GMVL-R36PS/Na
B-K
B-K
B-K
1
Side Plate of Air outlet
01494118
1
1
1
2
Left Support of Evaporator
01094122
1
1
1
Evaporator Sub-assy
01024231
01024230
01024232
1
3
1
1
4
Electric expand valve fitting
43040001
1
1
1
5
Right Support of Evaporator
01094121
1
1
1
6
Left Side Plate Sub-assy
01314172
1
1
1
7
Seal of left side Plate Sub-assy
01494115
1
1
1
8
Seal of left Connection Pipe
Sub-assy
01494116
1
1
1
9
Hook
02112446
4
4
4
10 Electric Box Cover
01424319
1
1
11 Top Cover Board Assy
01264176
1
1
1
12 Right Side Plate Sub-assy
01314175
1
1
1
0170905801
1
1
1
1570520103
1
1
1
13 Motor Support
14 Fan Motor
15 Motor Sub-assy
1570520201
150024011
1
1
1
02225234
1
1
1
17 Filter
11725202
1
1
1
18 Electric Box
01394994
1
1
1
19 Lower Cover Plate Sub-assy
01264178
1
1
1
01324341
1
1
1
21 Water Pump Assy
15404117
1
1
1
22 Terminal Border
42011106
1
1
1
23 Capacitor
33010027
1
1
1
24 Transformer
43110237
1
1
1
25 Main Bord
30226221
1
1
1
4001039509
1
1
1
27 Display Bord
30296013
1
1
1
28 Sensor sub-assy
39008026
1
1
1
16
20
Border Plate Assy of Air
ReturnEnd
Fan motor mounting Plate
Sub-assy
26 Connecting Wire
283
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMV-R22P/NaB-K
GMV-R28P/NaB-K
GMV-R36P/NaB-K
1
Side Plate of Air outlet
01494118
1
1
1
2
Left Support of Evaporator
01094122
1
1
1
Evaporator Sub-assy
01024231
01024230
01024232
1
3
1
1
4
Electric expand valve fitting
43040001
1
1
1
5
Right Support of Evaporator
01094121
1
1
1
Left Side Plate Sub-assy
01314172
1
1
1
01494115
1
1
1
01494116
1
1
1
02112446
4
4
4
10 Electric Box Cover
01424319
1
1
11 Top Cover Board Assy
01264176
1
1
1
12 Right Side Plate Sub-assy
01314175
1
1
1
0170905801
1
1
1
1570520103
1
1
1
6
7
8
9
Seal of left side Plate
Sub-assy
Seal of left Connection Pipe
Sub-assy
Hook
13 Motor Support
14 Fan Motor
15 Motor Sub-assy
1570520201
150024011
1
1
1
02225234
1
1
1
17 Filter
11725202
1
1
1
18 Electric Box
01394994
1
1
1
19 Lower Cover Plate Sub-assy
01264178
1
1
1
01324341
1
1
1
21 Water Pump Assy
15404117
0
0
0
22 Terminal Border
42011106
1
1
1
23 Capacitor
33010027
1
1
1
24 Transformer
43110237
1
1
1
25 Main Bord
30226168
1
1
1
4001039509
1
1
1
27 Display Bord
30296014
1
1
1
28 Sensor sub-assy
39008026
1
1
1
16
20
Border Plate Assy of Air
Return End
Fan motor mounting Plate
Sub-assy
26 Connecting Wire
284
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMV-R22PS/NaB-K GMV-R28PS/NaB-K GMV-R36PS/NaB-K
1 Side Plate of Air outlet
01494118
1
1
1
2 Left Support of Evaporator
01094122
1
1
1
01024231
01024230
01024232
1
3 Evaporator Sub-assy
4 Electric expand valve fitting
43040001
1
1
1
5 Right Support of Evaporator
01094121
1
1
1
6 Left Side Plate Sub-assy
01314172
1
1
1
01494115
1
1
1
01494116
1
1
1
9 Hook
02112446
4
4
4
10 Electric Box Cover
01424319
1
1
11 Top Cover Board Assy
01264176
1
1
1
12 Right Side Plate Sub-assy
01314175
1
1
1
0170905801
1
1
1
1570520103
1
1
1
Seal of left side Plate
7
Sub-assy
Seal of left Connection Pipe
8
Sub-assy
13 Motor Support
14 Fan Motor
15 Motor Sub-assy
1
1
1570520201
150024011
1
1
1
02225234
1
1
1
17 Filter
11725202
1
1
1
18 Electric Box
01394994
1
1
1
19 Lower Cover Plate Sub-assy
01264178
1
1
1
Fan motor mounting Plate
Sub-assy
01324341
1
1
1
21 Water Pump Assy
15404117
1
1
1
22 Terminal Border
42011106
1
1
1
23 Capacitor
33010027
1
1
1
24 Transformer
43110237
1
1
1
25 Main Bord
30226222
1
1
1
4001039509
1
1
1
27 Display Bord
30296014
1
1
1
28 Sensor sub-assy
39008026
1
1
1
16
20
Border Plate Assy of Air
Return End
26 Connecting Wire
285
DIGITAL MULTI VRF
No
MAINTENANCE
Name
Material Code
Qty
GMVL-R45PS/NaB-K
GMVL-R45P/NaB-K
1
Side Plate of Air outlet
01498641
1
1
2
Left Support of Evaporator
01805280
1
1
3
Evaporator Sub-assy
01024211
1
1
4
Electric expand valve fitting
43040001
1
1
5
Right Support of Evaporator
01078625
1
1
6
Left Side Plate Sub-assy
01314230
1
1
7
Seal of left side Plate Sub-assy
01494128
1
1
8
Seal of Connection Pipe Sub-assy
01498640
1
1
9
Hook
02112466
4
4
10 Electric Box Cover
01425249
1
1
11 Top Cover Board Assy
01259064
1
1
12 Right Side Plate Sub-assy
01308670
1
1
13 Motor Support
01709056
1
1
1501832202
1
1
15 Motor Sub-assy
15002401
2
2
16 Border Plate Assy of Air Return End
02225234
1
1
17 Filter
11725202
1
1
18 Electric Box
01394739
1
1
19 Lower Cover Plate Sub-assy
01265296
1
1
20 Fan motor mounting Plate Sub-assy
01339058
1
1
21 Water Pump Assy
15404121
1
0
22 Terminal Border
42011106
1
1
23 Capacitor
33010010
1
1
24 Transformer
43110237
1
1
30226221
1
14 Fan Motor
25 Main Bord
26 Connecting Wire
30226167
1
4001039509
1
1
27 Display Bord
30296013
1
1
28 Sensor sub-assy
39004167
1
1
286
DIGITAL MULTI VRF
No
MAINTENANCE
Name
Material Code
Qty
GMV-R45PS/NaB-K
GMV-R45P/NaB-K
1
Side Plate of Air outlet
01498641
1
1
2
Left Support of Evaporator
01805280
1
1
3
Evaporator Assy
01024211
1
1
4
Electric expand valve fitting
43040001
1
1
5
Right Support of Evaporator
01078625
1
1
6
Left Side Plate Sub-assy
01314230
1
1
7
Seal of left side Plate Sub-assy
01494128
1
1
8
Seal of Connection Pipe Sub-assy
01498640
1
1
9
Hook
02112466
4
4
10 Electric Box Cover
01425249
1
1
11 Top Cover Board Assy
01259064
1
1
12 Right Side Plate Sub-assy
01308670
1
1
13 Motor Support
01709056
1
1
1501832202
1
1
15 Motor Sub-assy
15002401
2
2
16 Border Plate Assy of Air Return End
02225234
1
1
17 Filter
11725202
1
1
18 Electric Box
01394739
1
1
19 Lower Cover Plate Sub-assy
01265296
1
1
20 Fan motor mounting Plate Sub-assy
01339058
1
1
21 Water Pump Assy
15404121
1
0
22 Terminal Border
42011106
1
1
23 Capacitor
33010010
1
1
24 Transformer
43110237
1
1
30226222
1
14 Fan Motor
25 Main Bord
26 Connecting Wire
30226168
1
4001039509
1
1
27 Display Bord
30296014
1
1
28 Sensor sub-assy
39004167
1
1
287
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMVL-R56P/NaB-K
GMVL-R71P/NaB-K
1 Side Plate of Air outlet
01499074
1
1
2 Left Support of Evaporator
01078603
1
1
3 Evaporator Sub-assy
01024234
1
1
4 Electric expand valve fitting
43040001
1
1
5 Right Support of Evaporator
01078604
1
1
6 Left Side Plate Sub-assy
01314225
1
1
7 Seal of left side Plate Sub-assy
01494131
1
1
8 Seal of left Connection Pipe Sub-assy
01494129
1
1
9 Hook
02112466
4
4
10 Electric Box Cover
01425249
1
1
11 Top Cover Board Assy
01258651
1
1
12 Right Side Plate Sub-assy
01308679
1
1
13 Motor Support
01708502
1
1
1570521101
1
1
15018603
1
1
15018604
1
1
16 Border Plate Assy of Air Return End
01499074
1
1
17 Filter
11129066
1
1
18 Electric Box
01394997
1
1
19 Lower Cover Plate Sub-assy
01258612
1
1
20 Fan motor mounting Plate Sub-assy
01324350
1
1
21 Water Pump Assy
15404119
0
0
22 Terminal Border
42011106
1
1
23 Capacitor
33010014
1
1
24 Transformer
43110239
1
1
25 Main Bord
30226167
1
1
4001039509
1
1
27 Display Bord
30296013
1
1
28 Sensor sub-assy
39008026
1
1
14 Fan Motor
15 Motor Sub-assy
26 Connecting Wire
288
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMVL-R56PS/NaB-K
GMVL-R71PS/NaB-K
1 Side Plate of Air outlet
01499074
1
1
2 Left Support of Evaporator
01078603
1
1
3 Evaporator Sub-assy
01024234
1
1
4 Electric expand valve fitting
43040001
1
1
5 Right Support of Evaporator
01078604
1
1
6 Left Side Plate Sub-assy
01314225
1
1
7 Seal of left side Plate Sub-assy
01494131
1
1
8 Seal of left Connection Pipe Sub-assy
01494129
1
1
9 Hook
02112466
4
4
10 Electric Box Cover
01425249
1
1
11 Top Cover Board Assy
01258651
1
1
12 Right Side Plate Sub-assy
01308679
1
1
13 Motor Support
01708502
1
1
1570521101
1
1
15018603
1
1
15018604
1
1
16 Border Plate Assy of Air Return End
01499074
1
1
17 Filter
11129066
1
1
18 Electric Box
01394997
1
1
19 Lower Cover Plate Sub-assy
01258612
1
1
20 Fan motor mounting Plate Sub-assy
01324350
1
1
21 Water Pump Assy
15404119
1
1
22 Terminal Border
42011106
1
1
23 Capacitor
33010014
1
1
24 Transformer
43110239
1
1
25 Main Bord
30226221
1
1
4001039509
1
1
27 Display Bord
30296013
1
1
28 Sensor sub-assy
39008026
1
1
14 Fan Motor
15 Motor Sub-assy
26 Connecting Wire
289
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMV-R56P/NaB-K
GMV-R71P/NaB-K
1 Side Plate of Air outlet
01499074
1
1
2 Left Support of Evaporator
01078603
1
1
3 Evaporator Sub-assy
01024234
1
1
4 Electric expand valve fitting
43040001
1
1
5 Right Support of Evaporator
01078604
1
1
6 Left Side Plate Sub-assy
01314225
1
1
7 Seal of left side Plate Sub-assy
01494131
1
1
8 Seal of left Connection Pipe Sub-assy
01494129
1
1
9 Hook
02112466
4
4
10 Electric Box Cover
01425249
1
1
11 Top Cover Board Assy
01258651
1
1
12 Right Side Plate Sub-assy
01308679
1
1
13 Motor Support
01708502
1
1
1570521101
1
1
15018603
1
1
15018604
1
1
16 Border Plate Assy of Air Return End
01499074
1
1
17 Filter
11129066
1
1
18 Electric Box
01394997
1
1
19 Lower Cover Plate Sub-assy
01258612
1
1
20 Fan motor mounting Plate Sub-assy
01324350
1
1
21 Water Pump Assy
15404119
0
0
22 Terminal Border
42011106
1
1
23 Capacitor
33010014
1
1
24 Transformer
43110239
1
1
25 Main Bord
30226168
1
1
4001039509
1
1
27 Display Bord
30296014
1
1
28 Sensor sub-assy
39008026
1
1
14 Fan Motor
15 Motor Sub-assy
26 Connecting Wire
290
DIGITAL MULTI VRF
No
MAINTENANCE
Name
Material Code
Qty
GMV-R56PS/NaB-K
GMV-R71PS/NaB-K
1
Side Plate of Air outlet
01499074
1
1
2
Left Support of Evaporator
01805279
1
1
3
Evaporator Assy
01024234
1
1
4
Electric expand valve fitting
43040001
1
1
5
Right Support of Evaporator
01078604
1
1
6
Left Side Plate Sub-assy
01314225
1
1
7
Seal of left side Plate Sub-assy
01494131
1
1
8
Seal of Connection Pipe Sub-assy
01494129
1
1
9
Hook
02112466
4
4
10 Electric Box Cover
01425249
1
1
11 Top Cover Board Assy
01258651
1
1
12 Right Side Plate Sub-assy
01308679
1
1
13 Motor Support
01708502
1
1
1570521101
1
1
15018603
1
1
15018604
1
1
16 Border Plate Assy of Air Return End
01499074
1
1
17 Filter
11129067
1
1
18 Electric Box
01394739
1
1
19 Lower Cover Plate Sub-assy
01258612
1
1
20 Fan motor mounting Plate Sub-assy
01324350
1
1
21 Water Pump Assy
15404119
1
1
22 Terminal Border
42011106
1
1
23 Capacitor
33010014
1
1
24 Transformer
43110239
1
1
14 Fan Motor
15 Motor Sub-assy
25 Main Bord
30226222
1
1
4001039509
40010232
1
1
27 Display Bord
30296014
1
1
28 Sensor sub-assy
39004167
1
1
29 Remote Controller
305125063
1
1
26 Connecting Wire
291
DIGITAL MULTI VRF
MAINTENANCE
(6)GMV(L)-R90P/NaB-K, GMV(L)-R90PS/NaB-K, GMV(L)-R112P/NaB-K,
GMV(L)-R112PS/NaB-K, GMV(L)-R140P/NaB-K, GMV(L)-R140PS/NaB-K
292
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMVL-R90P/NaB-K GMVL-R112P/NaB-K GMVL-R140P/NaB-K
1 Air outlet side board assy
01498608
1
1
1
2 Water pump assy
15404119
0
0
0
3 Water level switch
45010201
0
0
0
4 Electric expand valve fitting
43040001
1
1
1
1
1
1
1
Fan motor mounting Plate
7
Sub-assy
01024233
01024218
01805279
01804703
01324349
01325293
1
1
8 Top Cover Board Assy
01258607
1
1
9 Right support of evaporator
01078604
01805221
1
1
10 Right Side Plate Sub-assy
01308679
1
1
11 Air intake side-board sub-assy
01375221
1
1
1
12 Filter Sub-assy
11725205
1
1
1
13 Fan Motor
15018603
2
2
2
15018604
1
1
1
1570521101
1570520901
1570521201
1570521001
1
1
5 Evaporator assy
6 Left support of evaporator
14 Fan Motor
15 Motor
16 Motor
1
1
1
1
1
1
1
1
1
17 Bottom cover plate assy
01258603
1
1
1
18 Cover of air-in
01258602
1
1
1
19 Water tray assy
01284160
01284157
1
1
01394998
01394999
33010014
33010056
1
1
1
1
22 Capacitor
33010064
1
1
1
23 Terminal board
42011106
1
1
1
24 Transformer
43110239
1
1
1
25 Main board
30226221
1
1
1
26 Electric box cover
01425249
1
1
1
01494125
1
1
1
28 Left side plate assy
01494124
1
1
1
29 Seal of connection pipe
01494123
1
1
1
30 Hook
02118504
4
4
4
4001039509
1
1
1
32 Display board
30296013
1
1
1
33 Sersor sub-assy
39004167
1
1
1
20 Electric box assy
21 Capacitor
27
Seal of lefr side plate
sub-assy
31 Connecting Wire
1
1
1
293
DIGITAL MULTI VRF
MAINTENANCE
Qty
No
Name
Material Code
GMVL-R90PS/NaB-K GMVL-R112PS/NaB-K
GMVL-R140PS/NaBK
1 Air outlet side board assy
01498608
1
1
1
2 Water pump assy
15404119
1
1
1
3 Water level switch
45010201
1
1
1
4 Electric expand valve fitting
43040001
1
1
1
1
1
1
1
Fan motor mounting Plate
7
Sub-assy
01024233
01024218
01805279
01804703
01324349
01325293
1
1
8 Top Cover Board Assy
01258607
1
1
9 Right support of evaporator
01078604
01805221
1
1
10 Right Side Plate Sub-assy
01308679
1
1
Air intake side-board
11
sub-assy
01375221
1
1
1
12 Filter Sub-assy
11725205
1
1
1
13 Fan Motor
15018603
2
2
2
14 Fan Motor
15018604
1
1
1
1570521101
1570520901
1570521201
1570521001
1
1
1
1
17 Bottom cover plate assy
01258603
1
1
1
18 Cover of air-in
01258602
1
1
1
19 Water tray assy
01284160
01284157
1
1
01394998
01394999
33010014
33010056
1
1
1
1
22 Capacitor
33010064
1
1
1
23 Terminal board
42011106
1
1
1
24 Transformer
43110239
1
1
1
25 Main board
30226221
1
1
1
26 Electric box cover
01425249
1
1
1
Seal of lefr side plate
27
sub-assy
01494125
1
1
1
28 Left side plate assy
01494124
1
1
1
29 Seal of connection pipe
01494123
1
1
1
30 Hook
02118504
4
4
4
4001039509
1
1
1
32 Display board
30296013
1
1
1
33 Sersor sub-assy
39004167
1
1
1
5 Evaporator assy
6 Left support of evaporator
15 Motor
16 Motor
20 Electric box assy
21 Capacitor
31 Connecting Wire
1
1
1
1
1
1
1
1
1
1
294
DIGITAL MULTI VRF
No
Name
MAINTENANCE
Material Code
Qty
GMV-R90P/NaB-K GMV-R112P/NaB-K GMV-R140P/NaB-K
1
Air outlet side board assy
01498608
1
1
1
2
Water pump assy
15404119
0
0
0
3
Water level switch
45010201
0
0
0
4
Electric expand valve fitting
43040001
1
1
1
5
Evaporator assy
1
1
1
1
1
1
6
Left support of evaporator
7
Fan motor mounting Plate
Sub-assy
01024233
01024218
01805279
01804703
01324349
01325293
8
Top Cover Board Assy
01258607
1
1
Right support of evaporator
01078604
01805221
1
1
10 Right Side Plate Sub-assy
01308679
1
1
11 Air intake side-board sub-assy
01375221
1
1
1
12 Filter Sub-assy
11725205
1
1
1
13 Fan Motor
15018603
2
2
2
1
9
14 Fan Motor
1
1
1
1
1
15018604
1
1
1570521101
1570520901
1570521201
1570521001
1
1
1
1
17 Bottom cover plate assy
01258603
1
1
1
18 Cover of air-in
01258602
1
1
1
19 Water tray assy
01284160
01284157
1
1
01394998
01394999
33010014
33010056
1
1
1
1
22 Capacitor
33010064
1
1
1
23 Terminal board
42011106
1
1
1
24 Transformer
43110239
1
1
1
25 Main board
30226168
1
1
1
26 Electric box cover
01425249
1
1
1
27 Seal of lefr side plate sub-assy
01494125
1
1
1
28 Left side plate assy
01494124
1
1
1
29 Seal of connection pipe
01494123
1
1
1
30 Hook
02118504
4
4
4
4001039509
1
1
1
32 Display board
30296014
1
1
1
33 Sersor sub-assy
39004167
1
1
1
15 Motor
16 Motor
20 Electric box assy
21 Capacitor
31 Connecting Wire
1
1
1
1
1
295
DIGITAL MULTI VRF
No
Name
1 Air outlet side board assy
2 Water pump assy
3 Water level switch
4 Electric expand valve fitting
MAINTENANCE
Material Code
Qty
GMV-R90PS/NaB-K GMV-R112PS/NaB-K GMV-R140PS/NaB-K
01498608
1
1
15404119
15404118
45010201
450102012
1
1
1
1
1
1
1
43040001
1
1
01024233
01024218
01805279
01804703
01324356
01325293
01258607
01264627
01078604
01805221
1
1
1
1
1
1
1
1
1
1
10 Right Side Plate Sub-assy
01308679
1
1
11 Air intake side-board sub-assy
01375221
1
1
1
12 Filter Sub-assy
11725205
1
1
1
13 Fan Motor
15018603
2
2
2
15018604
1
1
1
1570521101
1570520901
1570521201
1570521001
01258603
0125860301
1
1
5 Evaporator assy
6 Left support of evaporator
Fan motor mounting Plate
7
Sub-assy
8 Top Cover Board Assy
9 Right support of evaporator
14 Fan Motor
15 Motor
16 Motor
17 Bottom cover plate assy
1
1
1
1
1
1
1
1
1
1
1
1
1
18 Cover of air-in
01258602
1
1
19 Water tray assy
01284160
01284157
1
1
01394986
01024218
33010014
33010056
1
1
1
1
22 Capacitor
33010064
1
1
1
23 Terminal board
42011106
1
1
1
24 Transformer
43110239
1
1
1
25 Main board
30226222
1
1
1
26 Electric box cover
01425249
1
1
1
Seal of lefr side plate
27
sub-assy
01494124
01494121
01314225
01314222
01494120
01494123
1
1
1
1
1
1
02118504
4
4
4
4001039509
1
1
1
32 Display board
30296014
1
1
1
33 Sersor sub-assy
39004167
1
1
1
20 Electric box assy
21 Capacitor
28 Left side plate assy
29 Seal of connection pipe
30 Hook
31 Connecting Wire
1
1
1
1
1
1
1
296
DIGITAL MULTI VRF
MAINTENANCE
5.2 .2 Cassette type indoor unit
(1)Exploded View of GMV(L)-R28T/Na-K, GMV(L)-R36T/Na-K, GMV(L)-R45T/Na-K,
GMV(L)-R50T/Na-K, GMV(L)-R56T/Na-K, GMV(L)-R71T/Na-K,
297
DIGITAL MULTI VRF
MAINTENANCE
Parts List of:
No.
Part Name
GMV-R28T/Na-K,
GMV-R36T/Na-K
GMVL-R28T/Na-K,
GMVL-R36T/Na-K
Code
Qty.
Code
Qty.
1
Tube Exit Plate
01382710
1
01382710
1
2
Body Fixed Plate
01332701
4
01332701
4
3
Front Side Plate
01302717
1
01302717
1
4
Left Side Plate
01302740
1
01302740
1
5
Base Plate
01222702
1
01222702
1
6
Rear Side Plate
01302719
1
01302719
1
7
Bottom Foam
52012716
1
52012716
1
8
Motor Gasket
76712711
3
76712711
3
9
Bolt
70212701
3
70212701
3
10
Motor Fixer
01702701
1
01702701
1
11
Fan Motor
15704901
1
15704901
1
12
Centrifugal Fan
10312721
1
10312721
1
13
Evaporator Connection
01072004
1
01072004
1
14
Cable-cross Loop
76513101
2
76513101
2
15
shunt
072287842
1
072287842
1
16
Water Tray
12412701
1
12412701
1
17
Screw
70140032
4
70140032
4
18
Electric Box Base Plate
01412721
1
01412721
1
19
Flow Guide Loop
10372701
1
10372701
1
20
Electric Box
20102701
1
20102701
1
21
Wire Clamp
22
Terminal Board
23
Transformer
T360B
71010102
4
71010102
4
42011222
1
42011222
1
43110233
1
43110233
1
24
Electric Box Cover I
20102702
1
20102702
1
25
Electric Box Cover II
20102703
1
20102703
1
26
Main Board
30226316
1
30226316
1
27
Capacitor
33010010
1
33010010
1
28
Rubber plug
76712701
1
76712701
1
29
Evaporator
01038778
1
01038778
1
30
Evaporator Support
01072003
2
01072003
2
31
Nut with Washer M6
70310012
1
70310012
1
32
Bolt subassembly
70210051
1
70210051
1
33
Pipe Pump PJV-1415
43130324
1
43130324
1
34
Pump Gasket
76712702
3
76712702
3
35
Pump Support
01332001
1
01332001
1
36
Water Level Switch
45010201
1
45010201
1
37
Drainage hose
05232721
1
05232721
1
38
Right Side Plate
01302710
1
01302710
1
39
Cable-cross Loop
76512702
1
76512702
1
Pump
40
Pump Cover
41
Bolt
42
Electronic Expansive Valve
01252710
1
01252710
1
70212701
0713411201/
07334281
3
70212701
0713411201/
07334281
3
1
1
298
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
GMV-R45T/Na-K,
GMV-R50T/Na-K
GMVL-R45T/Na-K,
GMVL-R50T/Na-K
Code
Qty.
Code
Qty.
1
Tube Exit Plate
01382710
1
01382710
1
2
Body Fixed Plate
01332701
4
01332701
4
3
Front Side Plate
01302717
1
01302717
1
4
Left Side Plate
01302740
1
01302740
1
5
Base Plate
01222702
1
01222702
1
6
Rear Side Plate
01302719
1
01302719
1
7
Bottom Foam
52012716
1
52012716
1
8
Motor Gasket
76712711
3
76712711
3
9
Bolt
70212701
3
70212701
3
10
Motor Fixer
01702701
1
01702701
1
11
Fan Motor
15704901
1
15704901
1
12
Centrifugal Fan
10312721
1
10312721
1
13
Evaporator Connection
01072004
1
01072004
1
14
Cable-cross Loop
76513101
2
76513101
2
15
shunt
07228807
1
07228807
1
16
Water Tray
12412701
1
12412701
1
17
Screw
70140032
4
70140032
4
18
Electric Box Base Plate
01412721
1
01412721
1
19
Flow Guide Loop
10372701
1
10372701
1
20
Electric Box
20102701
1
20102701
1
21
Wire Clamp
71010102
4
71010102
4
22
Terminal Board
42011222
1
42011222
1
23
Transformer
43110233
1
43110233
1
24
Electric Box Cover I
20102702
1
20102702
1
25
Electric Box Cover II
20102703
1
20102703
1
26
Main Board
30226316
1
30226316
1
27
Capacitor
33010010
1
33010010
1
28
Rubber plug
76712701
1
76712701
1
29
Evaporator
01038778
1
01038778
1
30
Evaporator Support
01072003
2
01072003
2
T360B
31
Nut with Washer M6
70310012
1
70310012
1
32
Bolt subassembly
70210051
1
70210051
1
33
Pipe Pump PJV-1415
43130324
1
43130324
1
34
Pump Gasket
76712702
3
76712702
3
35
Pump Support
01332001
1
01332001
1
36
Water Level Switch
45010201
1
45010201
1
37
Drainage hose
05232721
1
05232721
1
38
Right Side Plate
01302710
1
01302710
1
39
Cable-cross Loop
76512702
1
76512702
1
40
Pump Cover
01252710
1
01252710
1
41
Bolt
3
Electronic Expansive Valve
70212701
0713411201/
07334281
3
42
70212701
0713411201/
07334281
Pump
1
1
299
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
GMV-R56/63/71T/Na-K
Code
Qty.
GMVL-R56/63/71T/Na-K
Code
Qty.
1
Tube Exit Plate
01382711
1
01382711
1
2
Body Fixed Plate
01332701
4
01332701
4
3
Front Side Plate
01302718
1
01302718
1
4
Left Side Plate
01302715
1
01302715
1
5
Base Plate
01222702
1
01222702
1
6
Rear Side Plate
01302714
1
01302714
1
7
Bottom Foam
52012711
1
52012711
1
8
Motor Gasket
76712711
3
76712711
3
9
Bolt
70212701
3
70212701
3
10
Motor Fixer
01702701
1
01702701
1
11
Fan Motor
15704102
1
15704102
1
12
Centrifugal Fan
10312705
1
10312705
1
13
Evaporator Connection
01072710
1
01072710
1
14
Cable-cross Loop
76513101
2
76513101
2
15
shunt
07228806
1
07228806
1
16
Water Tray
12412701
1
12412701
1
17
Screw
70140032
4
70140032
4
18
Electric Box Base Plate
01412721
1
01412721
1
19
Flow Guide Loop
10372701
1
10372701
1
20
Electric Box
20102701
1
20102701
1
21
Wire Clamp
71010102
4
71010102
4
22
Terminal Board
42011222
1
42011222
1
23
Transformer
43110233
1
43110233
1
24
Electric Box Cover I
20102702
1
20102702
1
25
Electric Box Cover II
20102703
1
20102703
1
T360B
26
Main Board
30226316
1
30226316
1
27
Capacitor
33010010
1
33010010
1
28
Rubber plug
76712701
1
76712701
1
29
Evaporator
01004641
1
01004641
1
30
Evaporator Support
01072715
2
01072715
2
31
Nut with Washer M6
70310012
1
70310012
1
32
Bolt subassembly
70210051
1
70210051
1
33
Pipe Pump PJV-1415
43130324
1
43130324
1
34
Pump Gasket
76712702
3
76712702
3
35
Pump Support
01332001
1
01332001
1
36
Water Level Switch
45010201
1
45010201
1
37
Drainage hose
05232721
1
05232721
1
38
Right Side Plate
01302716
1
01302716
1
39
Cable-cross Loop
76512702
1
76512702
1
40
Pump Cover
01252711
1
01252711
1
41
Bolt
70212701
3
70212701
3
42
Electronic Expansive Valve
0713411401
1
0713411401
1
Pump
300
DIGITAL MULTI VRF
MAINTENANCE
(2)Exploded View of GMV(L)-R90T/Na-K,GMV(L)-R112T/Na-K, GMV(L)-R125T/Na-K ,
GMV(L)-R140T/Na-K,
301
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
GMV-R90/112/125/140T/Na-K
GMVL-R90/112/125/140T/Na-K
Code
Qty.
Code
Qty.
Tube Exit Plate
01382711
1
01382711
1
4
01332701
4
3
Body Fixed Plate
Front Side Plate
01332701
01302713
1
01302713
1
4
Left Side Plate
01302711
1
01302711
1
5
Base Plate
01222702
1
01222702
1
Rear Side Plate
Bottom Foam
01302709
1
01302709
1
52012717
1
52012717
1
76712711
3
76712711
3
70212701
3
70212701
3
1
01702701
1
11
Motor Fixer
Fan Motor
01702701
15704103
1
15704103
1
12
Centrifugal Fan
10310101
1
10310101
1
13
1
2
6
7
8
9
10
Motor Gasket
Bolt
Evaporator Connection
01072733
1
01072733
1
14
Cable-cross Loop
76512702
2
76512702
2
15
07228804
1
07228804
1
16
shunt
Electronic Expansive Valve
07334102
1
07334102
1
17
Water Tray
12412701
1
12412701
1
18
Screw
70140032
4
70140032
4
19
Electric Box Base Plate
01412721
1
01412721
1
20
Flow Guide Loop
10372701
1
10372701
1
21
Electric Box
20102701
1
20102701
1
22
Wire Clamp
71010102
4
71010102
4
23
Terminal Board
42011142
1
42011142
1
24
Transformer
43110233
1
43110233
1
25
Electric Box Cover I
20102702
1
20102702
1
26
Electric Box Cover II
20102703
1
20102703
1
27
Main Board
30226316
1
30226316
1
1
33010012
1
29
Capacitor
Rubber plug
33010012
76712701
1
76712701
1
30
Evaporator
01004640
1
01004640
1
31
Evaporator Support
Nut with Washer M6
01072708
2
01072708
2
32
70310012
1
70310012
1
33
Bolt subassembly
70210051
1
70210051
1
34
Pipe Pump PJV-1415
43130324
1
43130324
1
35
28
T360B
Pump Gasket
76712702
3
76712702
3
36
Pump Support
01332001
1
01332001
1
37
Water Level Switch
45010201
1
45010201
1
38
Drainage hose
05232721
1
05232721
1
39
Right Side Plate
Cable-cross Loop
01302716
1
01302716
1
40
76512702
1
76512702
1
41
Pump Cover
01252711
1
01252711
1
42
Bolt
70212701
3
70212701
3
Pump
302
DIGITAL MULTI VRF
MAINTENANCE
(3)GMV-R22T/NaA-K、GMVL-R22T/NaA –K、GMV-R28T/NaA-K、GMVL-R28T/NaA -Kexploded
views
303
DIGITAL MULTI VRF
No
MAINTENANCE
Product Code
1
Display Board
2
GMV-R22T/NaA-K、GMVL-R22T/NaA –K、
GMV-R28T/NaA-K、GMVL-R28T/NaA -K
1
30296309
1
30296308
Water Tray
1
20182703
3
Water Tray Foam for Fresh Air Intaking
1
12312702
4
Water Tray Foam
1
12312703
5
Fan Fixer
1
76712709
6
Centifugal Fan
1
10312702
7
Motor FN11T-1
1
15704114
8
Evap Support
1
01844136
9
Evaporator Assy
1
01024194
10
Motor Support
1
01702702
11
Motor Gasket
1
76712705
12
Water Tray support
1
01332706
13
Front Side Plate
01302741
14
Body Fixer
1
4
01332705
15
Right Side Plate
2
01302743
16
Tube-exit plate
1
01382719
17
Cable-cross Loop
2
76515202
18
Noise Elimination Box
1
07444103
19
Electronic Expansion Valve
1
07334282
20
Expansion Valve Winding
Wire Clamp
1
4304000101
21
2
71010103
22
Electric Box Assy
1
01394806
1
01394938
23
24
Terminal Board
Transformer
1
1
43110226
25
Capacitor CBB61 2.5uF/450VAC
1
33010026
26
Main PCB Z6G25C
1
30226199
1
30226198
27
Electric Box Cover
01424238
28
42011106
Base Plate
1
1
29
Cord Baffle Plate
1
01362701
30
31
Connecting Wire
Left Baffle Plate
1
1
40010232
01362703
01222712
32
33
Evap Connection
1
01072713
Water Level Switch Support
1
24212705
34
Right Baffle Plate
1
01362702
35
Water Level Switch
1
450127011
36
Pump Gasket 1
1
76712707
37
Pump Gasket 2
1
76712708
38
Pump Drainage
1
05232722
39
Pump Support
1
1332707
40
Water Pump PSB-7
1
43130320
41
Wire Clamp
1
71010105
304
DIGITAL MULTI VRF
MAINTENANCE
(4)GMV-R36T/NaA -K、GMVL-R36T/NaA -K、GMV-R45T/NaA -K、GMVL-R45T/NaA -K、exploded
views
305
DIGITAL MULTI VRF
NO
MAINTENANCE
Product Code
1
Display Board
2
GMV-R36T/NaA -K、GMVL-R36T/NaA -K、
GMV-R45T/NaA -K、GMVL-R45T/NaA -K
1
30296309
1
30296308
Water Tray
1
20182703
3
Water Tray Foam for Fresh Air Intaking
1
12312702
4
Water Tray Foam
1
12312703
5
Fan Fixer
1
76712709
6
Centifugal Fan
1
10312702
7
Motor FN11T-1
1
15704114
8
Evap Support
1
01072714
9
Evaporator Assy
1
01029608
10
Motor Support
1
01702702
11
Motor Gasket
1
76712705
12
Water Tray support
1
01332706
13
Front Side Plate
01302741
14
Body Fixer
1
1
01332705
15
Right Side Plate
1
01302743
16
Tube-exit plate
1
01382719
17
Cable-cross Loop
1
76515202
18
Noise Elimination Box
1
07444103
19
Electronic Expansion Valve
1
07334282
20
Expansion Valve Winding
Wire Clamp
1
4304000101
21
2
71010102
22
Electric Box Assy
1
01394806
1
01394938
23
24
Terminal Board
Transformer
1
1
43110226
25
Capacitor CBB61 2.5uF/450VAC
1
33010026
26
Main PCB Z6G25C
1
30226199
1
30226198
27
Electric Box Cover
01424238
28
42011106
Base Plate
1
1
29
Cord Baffle Plate
1
01362701
30
Connecting Wire
31
Left Baffle Plate
1
1
40010232
01362703
32
33
Evap Connection
1
01072713
Water Level Switch Support
1
24212705
34
Right Baffle Plate
1
01362702
35
Water Level Switch
1
45012701
36
Pump Gasket 1
1
76712707
37
Pump Gasket 2
1
76712708
38
Pump Drainage
1
05232722
39
Pump Support
1
1332707
40
Water Pump PSB-7
1
43130320
41
Wire Clamp
1
71010105
01222712
306
DIGITAL MULTI VRF
MAINTENANCE
5.2 .3 1-way cassette Type Unit
307
DIGITAL MULTI VRF
MAINTENANCE
(1)GMV(L)-R22Td/Na-K
No.
Part Name
Qty.
Code
GMV-R22Td/Na-K
GMVL-R22Td/Na-K
1
Front Panel Assy(MT01)
1
TL1000120
TL1000120
2
Water Tray Assy
1
12412702
12412702
3
Water Lead
1
24212708
24212708
4
Evaporator Assy
1
01024103
01024103
5
Left Side Plate Assy
1
01302729
01302729
6
Cross Flow Fan
1
10352701
10352701
7
Base Plate Assy
1
01222714
01222714
8
Right Side Plate Assy
1
01302746
01302746
9
Rear Case assy
1
22202702
22202702
10
Fan Motor
1
1570410401
1570410401
11
Electric Box Assy
1
01404655
01404697
12
Main Board
1
30226034
30226033
13
Electric Box Cover Plate
1
01412725
01412725
Panel
14
Terminal Board Cover
1
222427221
222427221
15
Drainage Pump
1
43132701
43132701
16
Electronic Expansion Valve
1
07334129
07334129
17
Supporter
1
01792703
01792703
(2)GMV(L)-R28Td/Na-K、GMV(L)-R36Td/Na-K
No.
Part Name
Code
Qty.
GMV-R28Td/Na-K
GMV-R36Td/Na-K
GMVL-R28Td/Na-K
GMVL-R36Td/Na-K
1
Front Panel Assy(MT01)
1
TL1000120
TL1000120
2
Water Tray Assy
1
12412702
12412702
3
Water Lead
1
24212708
24212708
4
Evaporator Assy
1
01024104
01024104
5
Left Side Plate Assy
1
01302729
01302729
6
Cross Flow Fan
1
10352701
10352701
7
Base Plate Assy
1
01222714
01222714
8
Right Side Plate Assy
1
01302746
01302746
9
Rear Case assy
1
10
Fan Motor
1
22202702
1570410401
22202702
1570410401
11
Electric Box Assy
1
01404655
01404697
12
Main Board
1
30226034
30226033
13
Electric Box Cover Plate
1
01412725
01412725
14
Terminal Board Cover
1
222427221
222427221
15
Drainage Pump
1
43132701
43132701
16
Electronic Expansion Valve
1
07334129
07334129
17
Supporter
1
01792703
01792703
Panel
308
DIGITAL MULTI VRF
MAINTENANCE
5.2 .4Wall mounted type indoor unit
(1)Exploded View of GMV(L)-R22G/NaB-K,GMV(L)-R28G/NaB-K
309
DIGITAL MULTI VRF
MAINTENANCE
Parts List of
No.
Part Name
GMV(L)-R22G/NaB-K,
GMV(L)-R28G/NaB-K
Code
Qty.
1
Wall-Mounting Frame
01252220
1
2
Rear Case
222020012
1
3
Evaporator Assy
01004628
1
4
Cross Flow Fan
10352001
1
5
Ring of Bearing
76512203
1
6
Drainage hose
0523001401
1
7
Water Tray
20182027
1
8
Swing Louver
10512032
1
9
Swing Linkage 1
10582002
1
10
Swing Linkage 2
10582003
1
11
Front Case
20002215
1
12
Screw Cover
24252006
3
13
Filter
11122002
2
14
Remote Control Y612C
305125033
1
15
Decorate Piece
68012019
1
16
Receiver Board
30545702
1
17
Front Panel
20002209
1
18
Guide Louver 2
10512034
1
19
Guide Louver 1
10512033
1
20
Motor MP28VA
15212110
1
21
Motor Clamp A
26112017
1
22
Motor FN14A
150121081
1
23
Electric Box Cover
22242030
1
24
Terminal Board T4B3A
42011233
1
25
Covering Plate
201220061
1
26
Electric Box
20102178
1
27
Main PCB Z6H15C
30226074
1
28
Transformer 48X26F
43110226
1
29
Wire Clamp
71010103
1
30
Rear Clamp
24242001
1
31
Signal Cable
400103953
1
310
DIGITAL MULTI VRF
MAINTENANCE
(2)Exploded View of GMV(L)-R36G/NaB-K;GMV(L)-R45G/NaB-K
311
DIGITAL MULTI VRF
MAINTENANCE
Parts List of
No.
Part Name
GMV(L)-R36G/NaB-K;
GMV(L)-R45G/NaB-K
Code
Qty.
1
Wall-Mounting Frame
01252384
1
2
Rear Case
22202050
1
3
Evaporator Assy
01004629
1
4
Cross Flow Fan
10352005
1
5
Ring of Bearing
76712015
1
6
Drainage hose
05232411
1
7
Water Tray
20182030
1
8
Swing Louver
10512041
12
9
Swing Linkage
10582439
1
10
Front Case
200022955
1
11
Screw Cover
24252007
3
12
Filter
11122440
2
13
Remote Control Y612C
305160051
1
14
Decorate Piece
68012019
1
15
Receiver Board
30545552
1
16
Front Panel
20002292
1
17
Guide Louver
26112043
1
18
Guide Louver
26112042
1
19
Motor MP28EA
15212105
1
20
Right Motor Clamp
26112429
1
21
Motor FN22A
15012062
1
22
Electric Box Cover
22242017
1
23
Terminal Board T4B3A
42011233
1
Covering Plate
20102119
1
25
24
Electric Box
20102108
1
26
Main PCB Z6J15C
30226072
1
27
Transformer 48X26F
43110226
1
28
Wire Clamp
71010103
1
29
Rear Clamp
26112430
1
30
Signal Cable
400103953
1
312
DIGITAL MULTI VRF
MAINTENANCE
(3)Exploded View of GMV(L)-R50G/NaB-K;GMV(L)-R56G/NaB-K
313
DIGITAL MULTI VRF
MAINTENANCE
Parts List of
No.
Part Name
GMV(L)-R50G/NaB-K;
GMV(L)-R56G/NaB-K
Code
Qty.
1
Wall-Mounting Frame
01252004
1
2
Rear Case
22202329
1
3
Fan Bearing
76512203
1
4
Screw Cover
24252015
3
5
Swing Louver
10512429
11
6
Swing Link 1
10582057
1
7
Swing Link 2
10582058
1
8
Water Tray
20182057
1
9
Guide Louver(up)
10512085
1
10
Guide Louver(down)
10512086
1
11
Cross Flow Fan
10352022
1
12
Evaporator Assy
13
Drainage hose
01024147
1
0523001403
1
14
Evaporator Support
24212067
1
15
Filter
16
Front Case
11122048
2
200026529
1
17
Front Panel
01544115
1
18
Remote Controller Y512
305125063
1
19
Displaying Light Board
22432071
1
20
Electric Box Cover 1
20112019
1
21
Wire Clamp
71010103
1
22
Terminal Board T4B3A
42011233
1
23
Electric Box Cover
20112020
1
Main PCB
30226116
1
25
24
Transformer 57X25C
43110237
1
26
Room Sensor 15k
3900019813
1
3900019814
1
27
Tube Sensor
20k
3900019815
1
3900019816
1
42020063
3
28
Sensor Insert
29
Electric Box
20112018
1
30
Lower Shield of Electric Box
01592037
1
31
Upper Shield of Electric Box
01592038
1
32
Stepping Motor MP35XY
Motor Clamp
15212117
26112095
1
33
34
Helicoid tongue
26252009
1
35
Motor FN20C-PG
150120671
1
36
Pipe Clamp
24242001
1
37
Signal Cable
400103953
1
38
Fix sub-assy
01324110P
1
39
EXV sub-assy
07334255
1
40
Connecting Wire
40010267
1
1
314
DIGITAL MULTI VRF
MAINTENANCE
(4)Exploded View of GMV(L)-R22G/NaC-K;GMV(L)-R28G/NaC-K
315
DIGITAL MULTI VRF
MAINTENANCE
Parts List of
No.
Part Name
GMV(L)-R22G/NaC-K;
GMV(L)-R28G/NaC-K
Code
Qty.
1
Wall Mounting Frame
01252220
1
2
Rear Case
222020012
1
3
Evaporator Assy
01004628
1
4
Cross Flow Fan
10352001
1
5
O-Gasket of Cross Fan Bearing
76512203
1
6
Drain Pipe
0523001401
1
7
Water Tray
201820272
1
8
Air Louver
10512080
1
9
Swing Lever
10582002
1
10
Swing Lever
10582003
1
11
Front Case
200024442
1
12
Screw Cap
24252006
3
13
Filter
11122002
2
14
Remote Control Y512
305125063
1
15
Display Board
30545707
1
16
Front Panel
20002522
1
17
Guide Louver
10512034
1
18
Guide Louver
10512033
1
19
Stepping Motor
15212110
1
20
Motor Press Plate
26112014
1
21
Fan Motor
150121081
1
22
Electric Box Cover
22242030
1
23
4-bit Terminal Board
42011233
1
Electric Box Cover
201220061
1
25
Electric Box
20102178
1
26
Main PCB Z6H251B
30226077
1
27
Transformer
43110226
1
28
Fixed Clamp
71010103
1
29
Pipe Clamp
24242001
1
30
Connecting Wire(communicate)
400103953
1
24
316
DIGITAL MULTI VRF
MAINTENANCE
(5)Exploded View of GMV(L)-R36G/NaC-K;GMV(L)-R45G/NaC-K
317
DIGITAL MULTI VRF
MAINTENANCE
Parts List of
No.
Part Name
GMV(L)-R36G/NaC-K;
GMV(L)-R45G/NaC-K
Code
Qty.
1
Wall Mounting Frame
01252384
1
2
Rear Case Sub-Assy
22202051
1
3
Evaporator Assy
01004629
1
4
Cross Flow Fan
10352005
1
5
Ring of Bearing
76712015
1
6
Drain Pipe
0523001401
1
7
Water Tray
201820302
1
8
Air Louver
10512041
12
9
Swing Lever
10582439
1
10
Front Case
200025253
1
11
Screw Cap
24252007
3
12
Filter
11122440
2
13
Remote Control Y512
305125063
1
14
Display Board
30545558
1
15
Front Panel
20002524
1
16
Lower Guide Louver
26112043
1
17
Upper Guide Louver
26112042
1
18
Stepping Motor
15212105
1
19
Motor Right Clamp
26112429
1
20
Motor FN22G
150120623
1
21
Electric Box Cover
22242017
1
22
4-bit Terminal Board
42011233
1
23
Covering Plate
20102119
1
Electric Box
20102108
1
25
Main PCB Z6J251B
30226075
1
26
Transformer
43110226
1
27
Fixed Clamp
71010103
1
28
Rear Clamp
26112430
1
29
Connecting Wire(communicate)
400103953
1
24
318
DIGITAL MULTI VRF
MAINTENANCE
(6)GMV(L)-R71G/Na-K;GMV(L)-R80G/Na-K Exploded diagram and list of components
319
DIGITAL MULTI VRF
MAINTENANCE
Parts List of
NO.
1
Name
Wall-Mounting Frame
GMV(L)-R71G/Na-K;
GMV(L)-R80G/Na-K
Coding
01252398
Qty
1
2
Rear Case
22202091
1
3
Fan Bearing
76512203
1
4
Screw Cover
242520053
3
5
Swing Louver
10512110
15
6
Swing Link
10582040
3
7
Water Tray
20182043
1
8
Guide Louver(up)
10512062
1
9
Guide Louver(down)
10512063
1
10
Cross Flow Fan
10352420
1
11
Evaporator Assy
0102411202
1
12
Drainage Pipe
0523001404
1
13
Evaporator Support(left)
24212041
1
14
Filter
11122051
2
15
Front Case
26904107
1
16
Front Panel
20002698
1
17
Front Panel
22432258
1
A
18
Remote Controller Y512
305125063
1
19
Receiver Board JD
30046093
1
20
Electric Box Cover
20102252
1
21
Switch Lever
10582007
1
22
Wire Clamp
71010103
1
23
Terminal Board T4B3A
42011233
1
24
Electric Box Cover
201022513
1
25
Main PCB
30226420
1
26
Transformer 48X26G
43110233
1
27
Room Sensor
3900019813
1
3900019814
1
3900019815
1
3900019816
1
3
30
Sensor Insert
Electric Box
42020063
20102250
1
31
Lower Shield of Electric Box
01592034
1
Upper Shield of Electric Box
Stepping Motor MP24GA
01592033
15212102
1
34
Evaporator Support(rihgt)
24212042
1
35
Motor Clamp
26112069
1
36
Motor FN26D
150121053
1
37
38
Fixer(evaporator)
Pipe Clamp
39
28
29
32
33
Tube Sensor
1
02112009
1
26112071
1
Signal Cable
400103953
1
40
Fix sub-assy
01324110P
1
41
EXV sub-assy
07334255
1
42
Connecting Wire
40010267
1
320
DIGITAL MULTI VRF
MAINTENANCE
(7)GMV(L)-R22G/NaG-K;GMV(L)-R28G/NaG-K Exploded diagram and list of components
321
DIGITAL MULTI VRF
NO.
1
2
3
4
5
6
7
MAINTENANCE
Name
Wall-Mounting Frame
Rear Case assy
Evaporator Assy
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Electronic Expansion Valve Assy
Electronic Expansion Valve
Evaporator Support
Cross Flow Fan
Ring of Bearing
O-Gasket of Cross Fan Bearing
Helicoid tongue
Left Axile Bush
Crank
Axile Bush
Air Louver 1
Air Louver 2
Front Case Sub-Assy
Filter Sub-Assy
Receiver Window
Receiver Board D5183
Front Panel
Screw Cover
Guide Louver
Pipe Clamp
Stepping Motor
Motor Press Plate
Fan Motor
Electric Box Cover 1
Electric Box Cover 2
29
Electric Box Assy
30
Main PCB Z6N35A
31
32
33
34
35
36
37
38
39
40
41
Jumping Connector
Transformer 48X26F
Drainage hose
Rubber Plug
Power Cord
Signal Wire
Signal Wire
Display Board
Remote Controller
Switch Board
Electric expand valve fitting
GMV-R22G/NaG-K、GMVL-R22G/NaG-K
GMV-R28G/NaG-K、GMVL-R28G/NaG-K
Coding
Qty
1
01252013
1
2220210301
01024249
07334373
07334281
24212091
10454101
26152022
76512203
26112163
10512037
10582070
10542008
10512156
10512155
20012139
1112220401
22432230
30565007
20012122
24252016
10512157
26112164
1521210801
26112161
150120874
20122103
2012207506
01395015 ①
01395094 ②
30226326 ①
30226236 ②
4202300121
43110226
0523001401
76712012
4002048710
4001039509
40010232
30565007
30510041
30118018
4304000102
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Note:
a) ① is only applicable to GMV-R22G/NaG-K、GMV-R28G/NaG-K;
b) ② is only applicable to GMVL-R22G/NaG-K、GMV-R28G/NaG-K。
322
DIGITAL MULTI VRF
MAINTENANCE
(8)GMV(L)-R36G/NaG-K、GMV(L)-R45G/NaG-K、GMV(L)-R50G/NaG-K Exploded diagram
and list of components
323
DIGITAL MULTI VRF
NO.
MAINTENANCE
Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Front Panel Case
Filter
Front Case Assy
Screw Cover
Display Board
Evaporator Assy
Electric expand valve Assy
Electric expand valve
Evaporator Support
Cross Flow Fan
O-Gasket of Cross Fan Bearing
Bearing cushion rubber base
Rear Case
Wall-Mounting Frame
Helicoid tongue
Air Louver
Axile Bush
Left Axile Bush
Guide Louver
Crankshaft
Drainage Pipe
Air Louver
Pipe Clamp
Motor
Motor Press Plate
Lower Shield of Electric Box
27
Electric Box Assy
28
Electric Box
29
Main PCB
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Transformer
Electric Box Cover
Upper Shield of Electric Box
Electric Box Cover
Sensor Insert
Tube Sensor
Water-blocking Sheet
Remote Controller
Power Cord
Signal Wire
Display Board
Electric expand valve fitting
Switch Board
Stepping Motor
Note:
a)
b)
GMV-R36G/NaG-K、GMVL-R36G/NaG-K
GMV-R45G/NaG-K、GMVL-R45G/NaG-K
GMV-R50G/NaG-K、GMVL-R50G/NaG-K
Coding
Qty
20012260
1
11120011
1
20012288
1
24252016
3
30565038
1
01024250
1
07334374
1
07334283
1
24212100
1
10352019
1
76512203
1
26152022
1
22202109
1
01252218
1
26112177
1
10512116
1
10542008
1
10512037
1
10512115
1
10582070
1
05230014
1
10512117
1
26112164
1
15012113
1
26112178
1
01592091
1
01394970 ①
1
01395095 ②
1
20112108
1
30226330 ①
1
30226238 ②
1
43110237
1
20122128
1
01592092
1
2011208102
1
42020063
1
39008049
1
76912106
1
30510041
1
4002048710
1
4001039509
1
30565038
1
43040001
1
30118018
1
15012086
1
① is only applicable to GMV-R36G/NaG-K、GMV-R45G/NaG-K、GMV-R50G/NaG-K;
② is only applicable to GMVL-R36G/NaG-K、GMVL-R45G/NaG-K、GMVL-R50G/NaG-K。
324
DIGITAL MULTI VRF
MAINTENANCE
(9)GMV(L)-R56G/NaG-K、GMV(L)-R63G/NaG-K、GMV(L)-R71G/NaG-K Exploded diagram
and list of components
325
DIGITAL MULTI VRF
MAINTENANCE
Name
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Front Panel Case
Filter
Screw Cover
Front Case
Cross Flow Fan
Air Louver
Helicoid tongue
Left Axile Bush
Display Board
Bearing cushion rubber base
O-Gasket of Cross Fan Bearing
Rear Case Assy
Water-Tray Drainplug
Evaporator Support
Evaporator Assy
Thermal Insulation Tube
Electric Expansion Valve Sub-Assy
Elbow Protect Board
Water-blocking Sheet
Air Guard
Electric expand valve fitting
Wall-Mounting Frame
Pipe Clamp
Drainage Pipe
Motor Clamp
Motor FN25A-PG
Stepping Motor MP35XX
Crankshaft
Filter Sub-Assy
Guide Louver
Axile Bush
Transformer 57X25C
Wire Retaining Band
34
Electric Box
35
36
37
Wire Clamp
Switch Board
Electric Box Cover 2
38
Main PCB
39
40
41
Lower Shield of Electric Box
Electric Box Cover 1
Upper Shield of Electric Box
42
Electric Box Assy
43
44
45
46
47
48
Note:
a)
b)
Remote Controller YB1FA
Power Cord
Connecting Cable
Connecting Cable
Display Board
Sensor sub-assy
GMV-R56G/NaG-K、GMVL-R56G/NaG-K、
GMV-R63G/NaG-K、GMVL-R63G/NaG-K、
GMV-R71G/NaG-K、GMVL-R71G/NaG-K
Coding
Qty
1
20012328
2
11120011
3
24252016
1
20012295
1
10454103
3
10512159
1
26112187
1
10512037
1
30565038
1
26152025
1
76512203
1
22202117
1
76712012
1
24212103
1
01024251
0.7m
75080005
1
07334386
1
01072493
1
76814104
1
01354124P
1
4304000102
1
01252002
1
26112188
1
0523001405
1
26112184
1
15012098
1521300101
1
1
10582070
1
11122091
1
10512118
2
10542008
1
43110237
1
26112181
2011210803 ①
1
20112108 ②
1
1
71012064
1
30118018
1
2011208104
30226256 ①
1
30226255 ②
1
1
01592091
1
20122128
1
01592092
01395068 ①
1
01395096 ②
1
1
30510041
4002048710
1
1
40010232
4001039509
1
1
30565038
1
39008049
① is only applicable to GMV-R56G/NaG-K、GMV-R63G/NaG-K、GMV-R71G/NaG-K;
② is only applicable to GMVL-R56G/NaG-K、GMVL-R63G/NaG-K、GMVL-R71G/NaG-K。
326
DIGITAL MULTI VRF
MAINTENANCE
5.2 .5 Floor ceiling type indoor unit
(1)Exploded View of GMV(L)-R28Zd/Na-K,GMV(L)-R36Zd/Na-K,GMV(L)-R50Zd/Na-K
327
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
1
Rear Side Plate
2
3
4
GMV(L)-R28Zd/Na-K,
GMV(L)-R36Zd/Na-K,
GMV(L)-R50Zd/Na-K
Code
Qty.
01302013
1
Handle
26232001
4
Left Decoration Plate
261124152
1
Rear Side Plate of Air Outlet
0130201501
1
5
Louver
1051953202
1
6
Right Decoration Plate
261124162
1
7
Shaft of Louver II
10512026
2
8
Louver Support
24212019
2
9
Shaft of Louver I
10512025
1
10
Louver Fixer
24212018
1
11
Swing Louver
10512027
12
12
Connecting Lever
10582009
1
13
Connecting Lever
10582008
2
14
Right Swing Motor Fixer
26152006
1
15
Right Fixing Plate of Evaporator
01072411
1
16
Right Side Foam sub-assy
12312404
1
17
Right Fixing Plate
01332404
1
18
Right Decoration Panel
19
Pipe Clamp Plate
26112027
1
0107243701
1
20
Capacitor 1uF/500V
33010089
1
21
22
Transformer 57X25C
43110237
1
Electric Box
01402407
1
23
Main PCB Z6935
30226903
1
24
Terminal Board RS9413G
42011159
1
25
Wire Base
24253001
1
Wire Clamp
24253002
1
26
Fuse 5A 250VAC
46010013
1
27
Cover of Electric Box
01412408
1
28
Pipe Clip
70812001
1
29
Drainage hose
Display Board
05235433
30545654
1
30
31
Electric Box
20102138
1
32
Front Grill Clip 1
26252002
4
33
Filter
11122013
2
34
Front Grill
22412010
2
35
Front Grill Clip 2
26252003
4
36
Front Panel
01544106
1
37
Front Panel
01532001P
1
38
Water Tray Panel
01272205P
1
39
Motor Support
01709532
1
40
Left Decoration Panel
26112028
1
41
Left Fixing Plate
01332405
1
5T52
1
328
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
GMV(L)-R28Zd/Na-K,
GMV(L)-R36Zd/Na-K,
GMV(L)-R50Zd/Na-K
Code
Qty.
43
Left Fixing Plate of Evaporator
01072410
1
44
Motor Clamp
26112026
4
45
Step Motor MP35CA
15212402
2
46
Left Swing Motor Fixer
26152005
1
01024134 ①
1
01024135 ②
1
47
Evaporator Assy
01024121 ③
1
48
Water Lead Panel
01362001
1
49
Cover of Evaporator
01072409
1
50
Fixed Mount
01708763
1
51
Centrifugal Fan
10312401
2
52
Rear Snail Shell
22202032
2
53
Front Snail Shell
22202031
2
54
Bar Clasp
70819522
4
55
Hoop
70819521
1
56
Motor
57
Remote Controller
58
Signal Cable
400103953
1
59
Fix sub-assy
01324110P
1
60
EXV sub-assy
07334258
1
61
EXV
07334191
1
62
Magnet Coil for EXV DPF-AS001A
430001087
1
Display Board Z63351F
30296309
1
63
Note:
a)
b)
c)
d)
e)
SPF-16D70
15707302 ④
1
157073024 ⑤
1
305125063
1
Evaporator Assy ① is only applicable to GMV(L)-R28Zd/Na-K
Evaporator Assy ② is only applicable to GMV(L)-R36Zd/Na-K
Evaporator Assy ③ is only applicable to GMV(L)-R50Zd/Na-K
Motor ④ is only applicable to GMV(L)-R28Zd/Na-K,GMV(L)-R36Zd/Na-KMotor
Motor⑤ is only applicable to GMV(L)-R50Zd/Na-K
329
DIGITAL MULTI VRF
MAINTENANCE
(2)Exploded View of GMV(L)-R71Zd/Na-K
330
DIGITAL MULTI VRF
No.
MAINTENANCE
Part Name
GMV(L)-R71Zd/Na-K
Code
Qty.
1
Left Decoration Plate
261124172
1
2
Shaft of Louver I
10512025
2
3
Swing Louver Fixer sub-assy
013324232
1
4
Louver Support
24212020
3
5
Louver Fixer
24222016
2
6
Louver
105124042
1
7
Shaft of Louver II
10512026
2
8
Right Decoration Plate
261124212
1
9
Left Swing Motor Fixer
26152007
1
10
Front Panel
01532414
1
11
Display Box
20102138
1
12
Display Board 5T52
30545654
1
13
Front Panel
01544106
1
14
Right Swing Motor Fixer
26152008
1
15
Step Motor MP35CA
15212402
2
16
Motor Clamp
26112026
4
17
Water Tray
01272412
1
18
Auxiliary Water Tray
01272413
1
19
Pipe Clip
70812001
1
20
Drainage hose
05235433
1
21
Handle
26232001
4
22
Right Side Foam sub-assy
12312407
1
23
Right Fixing Palte
01332404
1
24
Support of Motor Bearing
01792408
2
25
Fixer of Motor Support
01792409
1
26
Right Decoration Panel
26112033
1
27
Pipe Clamp
01072424
1
28
Electric Box
01402407
1
29
Wire Base
24253001
1
30
31
Wire Clamp
24253002
1
Terminal Board
42011159
1
32
Fuse 5A 250VAC
46010013
1
33
Main PCB Z6935
30226903
1
34
Ring of Bearing
76512404
2
35
Fan Bearing
76512210
2
36
Transformer 57X25C
43110237
1
37
Cover of Electric Box
01412408
1
38
Centrifugal Fan
10312401
4
39
Rotary Axis
73012401
2
40
Capacitor CBB61 3uF/450
33010027
1
41
Motor FN100A
15012406
1
42
Motor Fixer
01722409
1
43
Motor Clamp
01702405
2
44
Axes Connector
73012403
2
45
Motor Fixing Plate
01332426
1
331
DIGITAL MULTI VRF
MAINTENANCE
46
Front Snail Shell
22202031
4
47
Rear Snail Shell
22202032
4
48
Rear Side Plate
01302429
1
49
Motor Support
01702410
1
50
Filter
11122012
2
51
Water Lead Plate
01362401
1
52
Front Grill
22412011
2
53
Front Grill Clip 2
26252003
4
54
Remote Controller
305125063
1
55
Front Grill Clip 1
26252002
4
56
Evaporator Assy
01024123
1
57
Cover of Evaporator
01072417
1
58
Left Decoration Panel
26112032
1
59
Left Fixing Plate
01332405
1
60
Left Side Foam sub-assy
12312406
1
61
Bearing Fixing Plate
01332407
1
62
Rear Side Plate of Air Outlet
01302405
1
63
Connecting Lever
10582008
3
64
Connecting Lever
10582009
2
65
Swing Louver
10512028
22
66
Signal Cable
400103953
1
67
EXV sub-assy
07334255
1
68
EXV SPF-18D88
07334193
1
69
Magnet Coil for EXV
430001087
1
70
Fix sub-assy
01324110P
1
71
Display Board Z63351F
30296309
1
332
DIGITAL MULTI VRF
MAINTENANCE
(3)Exploded View of GMV(L)-R90Zd/Na-K,GMV(L)-R112Zd/Na-K,GMV(L)-R125Zd/Na-K
333
DIGITAL MULTI VRF
NO.
MAINTENANCE
Description
GMV(L)-R90Zd/Na-K、
GMV(L)-R112Zd/Na-K、
GMV(L)-R125Zd/Na-K
Part Code
1
2
Left Decoration Plate
3
Swing Louver Fixer sub-assy
4
5
Qty
261124152
1
10512025
3
0133241802
1
Louver Support
24212019
4
Louver Fixer
24212018
3
6
Shaft of Louver II
10512026
2
7
8
Louver
105124082
1
Right Decoration Plate
261124162
1
9
Left Swing Motor Fixer
26152005
1
10
11
Front Panel
01532413
1
Display Box
20102138
1
12
Display Board 5T52
30545654
1
13
14
Front Panel
01544106
1
Right Swing Motor Fixer
26152006
1
15
Step Motor MP35CA
15212402
2
16
17
Motor Clamp
26112026
4
0127240802
1
18
Auxiliary Water Tray
01272409
1
19
20
Pipe Clip
70812001
1
Drainage Pipe
05235433
1
21
Handle
26232001
4
22
23
Right Side Foam sub-assy
12312404
1
Right Fixing Palte
01332404
1
24
Support of Motor Bearing
01792408
2
25
26
Fixer of Motor Support
01792407
1
Right Decoration Panel
26112027
1
27
Pipe Clamp
01072425
1
28
29
Electric Box
01402407
1
Wire Base
24253001
1
30
31
Wire Clamp
Terminal Board
24253002
42011159
1
1
32
Fuse 5A 250VAC
1
33
Main PCB Z6935
46010013
30226903
1
34
35
Ring of Bearing
76512404
2
Fan Bearing
76512210
1
36
Transformer 57×25C
43110237
1
37
38
Cover of Electric Box
01412408
1
Centrifugal Fan
10319051
4
39
Rotary Axis
73012402
2
40
Capacitor
33010064 ①
1
33010056 ②
1
41
Motor
15012405 ③
1
15012404 ④
1
Shaft of Louver I
Water Tray
334
DIGITAL MULTI VRF
MAINTENANCE
42
Motor Fixer
01722410
1
43
44
Motor Clamp
01702405
2
Axes Connector
73012403
2
45
Motor Fixing Plate
01332425
1
46
47
Front Snail Shell
22202030
4
Rear Snail Shell
22202029
4
48
Rear Side Plate
01302431
1
49
50
Motor Support
01702411
1
Filter
11122013
1
51
Water Lead Plate
01362407
1
52
53
Front Grill
22412010
4
54
Remote Controller
26252003
305125063
8
1
55
56
Evaporator Assy
01024122
1
Front Grill Clip 1
26252002
8
57
Cover of Evaporator
01072409
1
58
59
Left Decoration Panel
26112028
1
Left Fixing Plate
01332405
1
60
Left Side Foam sub-assy
12312403
1
61
62
Bearing Fixing Plate
01332406
1
Rear Side Plate of Air Outlet
01302416
1
63
Connecting Lever
10582008
2
64
65
Connecting Lever
10582009
4
Swing Louver
10512027
26
66
Signal Cable
400103953
1
67
68
Display Board
30296309
1
EXV sub-assy
07334256
1
69
EXV VPF-25D*B3
07334195
1
70
Magnet Coil for EXV
43000110
1
71
Fix sub-assy 2
01324110P
1
Note:
a)
b)
c)
d)
Front Grill Clip 2
Z63351F
Capacitor ① is only applicable to GMV(L)-R90Zd/Na-K
Capacitor ② is only applicable to GMV(L)-R112Zd/Na-K,GMV(L)-R125Zd/Na-K
Motor ③ is only applicable to GMV(L)-R90Zd/Na-K
Motor ④ is only applicable to GMV(L)-R112Zd/Na-K,GMV(L)-R125Zd/Na-K
335
DIGITAL MULTI VRF
MAINTENANCE
(4)GMV-R71Zd/NaB-K、GMV-R90Zd/NaB-K
336
DIGITAL MULTI VRF
NO.
MAINTENANCE
Name
1
2
3
4
Front Gill
Top Cover Plate Sub-assy
Water tray assy
Front volute casing
5
Fan Motor
6
7
8
9
10
11
12
13
14
15
16
Rear Connection Board
Centrifugal fan
Right Foam Sub-assy
Install plank
Connection Board
Right Side Plate Sub-assy
Right Cover Plate
Rotary Axis Sub-Assy
Rear volute casing
Install Board Sub-assy
Rear Side Plate Assy
17
Middle bar Plate Assy
18
19
Water Lead Plate Sub-Assy
Connected Board
20
Electric expand valve fitting
21
Evaporator Assy
22
Electronic Expansion Valve
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Plank
Front Connection Board
Display Board Sub-Assy
Remote Controller
Sensor sub-assy
Guide Louver
Display Board
Steping Motor
Left Foam Sub-assy
Left Side Plate Assy
Install plank
Left Cover Plate
Transformer
Electric Box cover
Main Board
Terminal Board
39
Electric Box Assy
40
Capacitor
GMV-R71Zd/NaB-K
GMV-R90Zd/NaB-K
Code
26909434
01269405
01289403
26905208
15709408①
15709407②
01349410
1041410101
12509412
01809402
02229406
01319408
26909422
73018052
26909419
01329406
0131941901
01249407①
0124940501②
02224151P
01344108
4304000103①
4304413203②
0102428401①
01024284②
07334283①
07334389②
26909409
01349408
0222940501
30510041
39008057
26909432
30294220
1521240206
12509409
01319406
01809401
26909416
4311023701
01429410P
30226910
42011106
01395131①
01395076②
33010011①
33010014②
Qty
1
1
1
3
1
1
1
3
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Note:
a) ① is only applicable to GMV-R71Zd/NaB-K;
b) ② is only applicable to GMV-R90Zd/NaB-K。
337
DIGITAL MULTI VRF
MAINTENANCE
(5)GMV-R112Zd/NaB-K、GMV-R140Zd/NaB-K
338
DIGITAL MULTI VRF
NO.
MAINTENANCE
Name
GMV-R112Zd/NaB-K
GMV-R140Zd/NaB-K
Code
Qty
1
Front Gill
26909425
1
2
Top Cover Plate Sub-assy
01269403
1
3
Water tray assy
01289401
1
4
Front volute casing
26905208
4
5
Fan Motor
15709405
1
6
Sensor sub-assy
39008057
1
7
Remote Controller
30510041
1
8
Rear Connection Board
01349411
1
9
Centrifugal fan
10
Plank
1041410101
4
01809404
01319408
1
11
Right Side Plate Sub-assy
12
Right Foam Sub-assy
12509412
1
13
Right Cover Plate
26909422
1
14
Rear volute casing
26909419
4
15
Rotate Axis
26909413
1
16
Rear Side Plate Assy
01319422
1
17
Water Lead Plate Sub-Assy
02224151P
1
18
Evaporator Assy
01024255①
1
01024270②
1
19
Electronic Expansion Valve
07334389
1
20
Connected Board
01344108
1
21
Plank
26909410
1
22
Front Connection Board
01349404P
1
23
Steping Motor
1521240201
1
24
Guide Louver
26909408
4
25
Display Board
30294220
1
26
Electric Box Assy
01395076
1
27
Electric Box cover
01429410P
1
28
Transformer
4311023701
1
29
Capacitor
33010014
1
30
Main Board
30226910
1
31
Terminal Board
42011106
1
32
Middle bar Plate Assy
0124940101
1
33
Steping Motor
1521240206
1
34
Left Cover Plate
1
35
Left Side Plate Assy
26909416
01319406
36
Left Foam Sub-assy
12509409
1
37
Display Board
30296309
1
1
1
Note:
a) ① is only applicable to GMV-R112Zd/NaB-K;
b) ② is only applicable to GMV-R140Zd/NaB-K。
339
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement