Thunder Data Sheet pdf

Thunder Data Sheet pdf
Any Light. Anywhere.
Any light, any
place, any
weather.
Now you can use
conventional
stage lights
outside, in any
climate.
Tempest’s Thunder Light-
Thunder 6600
enclosure, for most
standard ellipsoidal
spotlights – and
plenty of room for
accessories.
ing Enclosures are the right
way to use conventional
stage lights in outdoor locations.
THUNDER
Lighting Enclosures
Thunder
comes
in a wide range of sizes,
for all popular spotlights
and effects projectors, and
custom sizes are available
to special order for luminaires up to 2.5kW.
Thunder
now
comes
as
standard with Tempest’s
new MiniDECTM controller,
and may be specified with
DEC3TM control for full environmental and condensation protection.
You’re going
to like using
Thunder on your
next outdoor
lighting project.
Specification
ConstructionAluminum, plated and epoxy powder coated, and
stainless steel
Cooling
Glass
Tempered optical glass window
Cooldown
Fans run for 5 minutes after lamp turns off
Mounting
Two stainless steel Unistrut channels on base.
DMX
DMX wiring access for luminaire control
Security
Heavy duty stainless steel latches, may be padlocked
for extra security
Power
100-120V or 200-240VAC, 50/60Hz, single or split
feed wiring for enclosure and luminaire
Base Color
Light bronze powder coat. Custom colors to order.
Wiring
Separate Conduit entries for AC power and DMX
Tempest Lighting MiniDECTM control system.
MiniDEC monitors
temperature and power
to the lamp, controls
cooling and changes air
when the lamp is off to
prevent overheating in
direct sun.
Luminaire
Power OutletIEC 3-pin receptacle (rated 10amp 230V, 15amp
120V). Rewirable plug included.
Control
High-power AC fan changes filtered air every 1-2
seconds when luminaire lamp is on
Orientation May be installed base-up or base-down
DEC Option DEC3 Control, with full temperature and anti-condensation management, DMX and RDM remote monitoring functions
Scan Cover
UV resistant acrylic cover for moving mirror scan
luminaires. Large radius prevents image distortion.
Thunder for Spotlights and Effects Projectors
Thunder enclosures come in a range of standard sizes to fit most
popular stage lights and effects projectors. Luminaires mount to
a stainless steel Unistrut rail inside the enclosure, allowing simple
front-to-back position adjustment.
Thunder 6600
Most standard ellipsoidal spotlights
Thunder 6690
Rosco X24
Thunder 6691
Philips Showline Nitro Strobe
Thunder 6700
Most 10° ellipsoidals and smaller HMI profiles
Thunder 6800 Most 5° ellipsoidals and 1200W effects projectors
(Now including Selecon Pacific 5°)
Thunder 6700, for 10°
ellipsoidals and smaller
HMI profiles
Thunder Scan for Strobes and Moving Mirror Lights
Thunder is available for strobes and a wide range of moving mirror
scanners in three standard sizes. Thunder Scan comes with a clear,
UV-resistant acrylic cover, radiused around the mirror position to
prevent optical aberrations. Thunder Scan models are available in
three standard sizes with MiniDEC or DEC3 control.
Thunder Scan 6650
Strobes — Martin Atomic, Solaris Flare etc
Small Scans — MiniScan, Martin Mania etc
Thunder Scan 6750
Midsize Scans — Trackspot Bolt
Thunder Scan 6850
Large Scans — Golden Scan, Cyber 2.0
Thunder 6750, for
Midsize Scanners
Custom Thunder
Thunder enclosures may be customized for many applications, such as ballasts, strobes, lasers, even big HMIs
for TV production.
Of course, once we’ve built one it’s no longer really
custom, so here are some Thunders that we’ve made
for people that might fit the bill for your next outdoor
project.
Thunder 6670
for AAdynTech Punch
Plus LED luminaire. 6670
is available from AAdynTech with either the
stadium hanger shown or
a manual Yoke option.
Thunder 6900
If you want a REALLY bright profile, you need to
check out the Robert Juliat d’Artagnan, with 2,500W
of HMI power in that beam and beautiful optics for
pattern projection to boot.
Now you can safely use these amazing lights outdoors, using the Tempest Thunder 69000 enclosure, with DEC3.3 control and salt fog filtering as
standard equipment.
Thunder 6950
When our friends at FUNA needed to place four
Sharpies close together behind the pool deck band
we dreamed up this supersized Thunder enclosure,
complete with DEC3.3 and salt-fog filtering for a long
life at sea. Now you can try it too!
Mounting Kits
Two parallel 1 5/8” x 13/16” (41 x 21mm)
Unistrut. Use standard Unistrut accessories or
order any of the Tempest mounting kits shown
here.
Order two or four mounting kits for each enclosure,
depending on mounting method.
XYZ Yoke Kit
Thermal Insulation Kit
4900.MC Stainless Steel pipe clamp kit, for
pipes 1.5” (38mm) to 2” (50mm) OD.
4900.MC
4925.MC Stainless Steel pipe clamp kit, for
pipes 2” (50mm) to 2.5”/64mm OD.
The Blizzard XYZ Mount is a heavy duty yoke that attaches to the
Unistrut mounting rails on the base of any Blizzard or Thundser
enclosure, where it can be mounted at the center of gravity for
excellent balance. Range of adjustment:
Pan360°
Tilt
+60° to -90°
Roll±10°
Part # 6500.XYZ
The factory-fitted TI kit adds 1”/25mm of thermal insulation to the inside of any Thunder enclosure
(not available for Thunder Scan). This helps to moderate extreme temperatures in hot and cold
locations. Recommended where ambient temperatures are expected >40°C or <0°C.
Part #
6600.TI
Dimensions
CAD drawings in .dwg and
.pdf format are available
for download at
4900.MB Stainless Steel Bolt kit: 1/2” bolt,
washer, Spring nut (shaded)
A
1”/25
Max W
2”/50
Max L
www.tempest.org
B
Inlet cowl/filter
A
E
DMX
C
(Unistrut)
AC
D
Enclosure (“/mm)
Model
Exhaust cowl/fan
Luminaire (“/mm)
B
C
D
E
Max L
Max W
Max
Watts
6690/91
24/610
14/356
15/381
16.5/419
8/203
15/381
14.5/368
6600
32.5/830
16.5/420
15/380
15/380
8/203
26/660
14/360
1,200
700
6700
38.5/980
19/480
15/380
16.5/420
12/305
32.5/830
15.5/380
1,200
6800 *
51/1295
22/565
48/1220
20/508
8/203
45/1,143
18/457
1,200
Check drawings at tempest.org or with factory for models not shown here
* NEW — Thunder 6800 has been stretched to accept the Selecon Pacific 5° and 5-13° Zoom
Part Number Guide
____.__.____
ModelDescription
6600Thunder
6650 Thunder Scan, Small
6690 Thunder, Rosco X-Effect
6691 Thunder, Showline Nitro Strobe
6700 Thunder Stretch
6750 Thunder Scan Stretch
6800 Thunder X-Stretch
6950 Thunder Scan, 4 x Sharpy
6960 Thunder Scan, 3 x Super Sharpy
Shipping Weights/Dims.
Thunder
Thunder
Thunder
Thunder
6600,6650 6690 6700, 6750 6800, 6850 36”x18”x18”(h),
36”x18”x18”(h),
48”x24”x24”(h),
48”x24”x24”(h),
examples:
6600.US, 6700.IN.DEC
Electrical
US 120V, NEMA standard
North America
IN 230V, CE Standard
45lb
30lb
58lb
70lb
Optional Suffix
DEC
DEC Climate Control
X
International
91 x 46 x 46cm, 20kg
91 x 46 x 46cm, 14kg
122 x 117 x 117cm, 26kg
122 x 117 x 117cm, 32k
All: Schedule B Export Code: 8536.30.0000
User Manual
For more detailed information and installation/operating instructions, download
the Thunder User Manual from www.tempest.org
Custom (contact factory)
Digital Enclosure Control
All Thunder enclosures may be ordered upgraded to include
Tempest’s patented Digital Enclosure Control System (DEC),
GoldilocksTM
How do we keep your lights from
to provide not only weather protection but complete envi-
roasting when it’s 50°C and there’s
ronmental control, DMX and RDM remote monitoring.
no shade?
DEC3.3 with Tempest’s new Goldilocks
And prevent condensation from
TM
operating system, keeps
your equipment warm when it’s cold, cool when it’s hot, and pre-
destroying your investment over-
vents deadly condensation from corroding your equipment over the
night?
long haul. Remember, it’s not heat or cold that kills your equipment outside — it’s condensation.
•
Cooling: DEC monitors the current to your equipment and
Tempest’s new GoldilocksTM Operating System (patents pending)
brings enclosure control to a new level:
runs a powerful fan when it sees that your lights are running.
Goldilocks keeps the air temperature inside your enclosure just right,
DEC changes the air inside your enclosure about once a sec-
removing heat from the projector when the lamp is on or when the
ond, removing immediately the heat generated by your lamp.
enclosure is heated by the sun. We’re changing the air about once
During the day if it gets hot the fan kicks in and cools things
every second.
down.
•
Heat: in cold areas we monitor temperature and maintain it
above a minimum level that you can set – usually freezing
point. So your equipment will start first time, even when it’s 20
below out there.
•
Condensation: See the panel on the right. Goldilocks raises
the temperature any time there’s a risk of condensation, stopping it before it starts.
•
DMX: assign a DMX address to the enclosure and use it to
switch power to the equipment inside. Now you can run a hard
reset from the control room without climbing a ladder!
•
RDM: configure and monitor your enclosures from the control
room over RDM – a real boon in larger systems.
Goldilocks uses heaters to maintain a minimum temperature in cold
climates.
And Goldilocks tracks temperature and humidity 24/7, keeping
relative humidity inside your enclosure just right by using heaters
to raise the air temperature when needed, adapting constantly to
prevent deadly condensation.
Remote Monitoring
Now you ca use this handy PC interface to monitor all the environmental
and electrical data over your entire
system. The JESE RDM-TRI comes with
the GetSet PC software suite and functions as an efficient front end
to your entire RDM network, as well as featuring Tempest-specific
dashboards for enclosure management.
Tempest part #: 2000.190
Made in the USA
©Tempest Lighting, Inc., October 2015. In the interest of continuous product improvement, specifications are subject to change without notice
Tempest Lighting, Inc.,
11845 Wicks Street, Los Angeles, CA 91352, USA
www.tempest.org [email protected]
t: +1 888 649 6743
f: +1 818 982 5582
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement