PACSystems RX3i PROFINET Scanner, IC695PNS001

PACSystems RX3i PROFINET Scanner, IC695PNS001
PACSystems* RX3i
IC695PNS001-ABAC
PROFINET Scanner Module
GFK-2738C
July 2013
1
OK
2
LAN
3
STATUS
4
CONN
The PACSystems* RX3i PROFINET Scanner (PNS) module, IC695PNS001,
connects a remote universal RX3i I/O rack of Series 90-30 or RX3i modules to a
PROFINET IO-Controller. The PROFINET Scanner scans the modules in its rack,
retrieving input data and providing output data, and exchanges that data on the
PROFINET IO LAN at the configured production rate.
PNS001
SD CARD
TO INSTALL,
TORQUE TO
6 IN-LB.
ACTIVE
The PNS manages PROFINET communication and module configuration
between an IO-Controller and modules in the remote rack. If network
communications are lost, the PNS manages IO states according to the individual
module configurations.
The PNS supports 10/100/1000 Mbps Copper, 100/1000 Mbps Multi-mode Fiber,
and 100/1000 Mbps Single-mode Fiber. PROFINET communications on the
network require 100 or 1000 Mbps link speed. Although 10 Mbps cannot be used
for PROFINET communications, 10 Mbps can be used for other types of Ethernet
traffic such as PING.
Features of the RX3i PNS include:
USB !
USB
▪
Programming and configuration services for all supported Series 90-30 and
RX3i IO Modules using Proficy Machine Edition. For a list of currently
supported IO modules, see “Supported Modules, Power Supplies and
Backplanes,” on page 9.
▪
▪
Support for daisy-chain/line, star, or ring (redundant media) topologies.
▪
▪
The network can include media interfaces of more than one type.
IP ADDRESS
MAC ADDRESS
PORTS
FRONT
3 4
1 2
Four switched Ethernet ports - two 8-conductor RJ-45 shielded twisted pair
10/100/1000 Mbps copper interfaces and two Small Form-factor Pluggable
(SFP) cages for user-supplied SFP devices.
Support for transfer of IO-Device Name to another PNS module using an
SD card. This eliminates the need to connect a configuration tool, such as
Proficy Machine Edition when replacing a module.
▪
A USB port for field updates of firmware using WinLoader.
Note:
The USB port is for firmware upgrades only. It is not intended for
permanent connection.
I O DEVICE
Ordering Information
*
IC695PNS001
PACSystems RX3i PROFINET Scanner Module 10/100/1000
with four Ports (two SFP connections, two Copper)
Includes a blank SD card, two mounting screws and a USB port cover
IC695SPC100
RX3i 10/100/1000Base-T copper SFP
IC695SPF002
RX3i 100Base-FX (fiber 2 km) SFP (Multi mode fiber - MMF)
IC695SPF550
RX3i 1000Base-SX (fiber 550 m) SFP (MMF)
IC695SPF010
RX3i 1000Base-LX (fiber 10 km) SFP (Single mode fiber - SMF)
Indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other trademarks are the property of their
respective owners.
2
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
PNS Specifications
PROFINET Support
PROFINET Version 2.3 Class A IO-Device
Controller CPU Version
Required
CPU315/CPU320 with firmware version 7.10 or later
CPE305/CPE310 with firmware version 7.10 or later
RXi Controller firmware with version 7.80
Proficy Machine Edition
Version Required
Version 8.0 or later
Power Requirements
3.3V:
1.2A with no SFP devices installed
1.9A maximum (two SFP devices installed, 0.35A per SFP)
5V:
1.1A maximum
Operating Temperature Range
0 to 60°C
Derated to 57°C:
Number of Port Connectors
•
If 100MB Fiber SFPs installed, or
•
If Copper SFPs operating at 1GB
Two RJ-45 and Two SFP Cages
(SFP devices not included, available separately.)
USB Connector (for firmware
upgrades)
One Micro-B connector. USB 2.0 compliant running at Full-speed (12 MHz)
SD Card
Supports SD and SDHC cards.
PNS Status and Control Bits
32 input status bits and 32 output control bits
PROFINET IO production rate
(IO Update Rate)
Configurable selections: 1ms, 2ms, 4ms, 8ms, 16ms, 32ms, 64ms, 128ms, 256ms
or 512ms
Number of IP addresses
One. Supports Classless Inter-Domain Routing (CIDR)
Number of MAC Addresses
Five. One per external port and one internal.
IO Station Maximum Limits
Number of IO Modules per
station
Number of backplane slots minus one for PNS
and at least one for a power supply
IO data per station
2880 bytes total
1440 bytes of input data
1440 bytes of output data
Configuration
V2.3 GSDML file is included with Proficy Machine Edition; available for
rd
import into 3 -Party tools.
Note: Configuration software that supports GSDML V2.3 MenuList
elements (such as Proficy Machine Edition 8.0 or later) is required
to display the configuration parameters of most IC695xxx I/O
modules.
For product standards, general operating specifications, and installation requirements, refer to the
PACSystems RX3i System Manual, GFK-2314.
Additional Information
For additional information, please refer to the manuals listed below. Manuals can be downloaded from the
Support website, http://support.ge-ip.com.
PACSystems RX3i PROFINET Scanner Manual, GFK-2737
PACSystems RX3i PROFINET Controller Manual, GFK-2571
PACSystems RX3i PROFINET Controller Command Line Interface Manual, GFK-2572
PACSystems CPU Reference Manual, GFK-2222
PACSystems RX3i System Manual, GFK-2314
IC695PNS001-ABAC PROFINET Scanner Module
3
GFK-2738C
General Installation Requirements
This product is intended for use with the RX3i system. Its components are considered open equipment
[having live electrical parts that may be accessible to users] and must be installed in an ultimate enclosure
that is manufactured to provide safety. As a minimum, the enclosure shall provide a degree of protection
against solid objects up to 12mm (e.g. fingers). This equates to a NEMA/UL Type 1 enclosure or an IP20
rating (IEC60529) providing at least a pollution degree 2 environment.
Installation in Hazardous Areas
The system containing the RX3i PNS001 module must be mounted within an ultimate enclosure that can be
accessed only by the use of a tool.
The following information is for products bearing the UL marking for Hazardous Locations or ATEX
marking for explosive atmospheres:

EQUIPMENT LABELED WITH REFERENCE TO CLASS I, GROUPS A, B, C & D, DIV. 2 OR ZONE 2 HAZARDOUS
LOCATIONS IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D, ZONE 2 OR NONHAZARDOUS LOCATIONS ONLY

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS
I, DIVISION 2 OR ZONE 2;

WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN OFF POWER BEFORE
REPLACING OR WIRING MODULES; AND

WARNING - EXPLOSION HAZARD - DO NOT CONNECT OR DISCONNECT EQUIPMENT UNLESS POWER HAS
BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.
PROFINET Scanner Status and Control Data
The RX3i PROFINET Scanner provides 32 bits of input status data and receives 32 bits of output control
data. The application program in the IO-Controller system can monitor the input status bits for the PNS
module. The output control bits are reserved for future use and have no function at this time.
Output Control Bits:
The PROFINET Scanner’s 32 bits of control output are reserved for future use.
Input Status Bits
The PROFINET Scanner’s 32 bits of input status provide information about the
scanner. All status bits are active high.
Status
Bits
Name
Description
1
Module
OK
Indicates the health of the module. A value of 0 indicates the module is powering up or has
failed. A value of 1 indicates the module is functioning properly.
2
Reserved
Set to 0
3
Port1 Link
Up
4
Port2 Link
Up
1 = port is connected to another device and is communicating.
0 = port is not connected to another device, or the port has some sort of error preventing
communications.
5
Port3 Link
Up
6
Port4 Link
Up
7-10
Reserved
Set to 0
11
MRP
Enabled
Indicates whether MRP has been enabled or not. A value of 0 indicates that MRP is not
enabled. A value of 1 indicates that MRP is enabled.
12
MRP Role
Indicates the MRP role the PNS is operating as when MRP is enabled. A value of 0 indicates
that the PNS is currently an MRP Client. A value of 1 indicates that the PNS is currently an
MRP Manager, however the PNS does not currently support MRP Manager configuration. If
MRP is not enabled, then this bit will be set to zero.
13-32
Reserved
Set to 0
4
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
LEDs on the PROFINET Controller Module
Powerup LED Patterns
At powerup, the LEDs show the patterns described below. The LEDs also blink diagnostic patterns for certain
operating errors and for module identification.
2
All LEDs off
STATUS LED solid green
Description
Initial state
OK
2
LAN
3
STATUS
4
CONN
PNS001
Normal operation
OK LED blinks amber with special
blink code
Fatal initialization or diagnostics failure;
H/W Module Identity Information not
available
STATUS LED blinks red with
special blink code
Fatal initialization failure.
OK, LAN, and STATUS LEDs blink
green in unison (0.5 second ON/
0.5 second OFF)
Invalid firmware detected or firmware
update initiated. Module is waiting for
firmware update. Blink pattern continues
during firmware update. After the automatic
update completes, the LAN and STATUS
LEDs blink amber and the module resets,
which restarts the powerup process.
STATUS and LAN LEDs blink
green in unison (0.5 seconds ON/
0.5 seconds OFF)
Internal update in process following a
firmware update. Unit should complete
update and restart automatically.
3
LAN and STATUS LED solid green
Normal operation
4
OK LED solid green
Normal operation. Powerup completed.
Note:
1
TO INSTALL,
TORQUE TO
6 IN-LB.
SD CARD
1
LED/ Blink pattern
ACTIVE
USB
USB !
Step
IP ADDRESS
MAC ADDRESS
PORTS
FRONT
3 4
1 2
I O DEVICE
Under certain ambient operating temperatures, the PROFINET Scanner could momentarily display
the over temperature pattern during power up, while it is calibrating its thermal protection functions.
This indication can be ignored. For details, see “Microprocessor Over Temperature” in the
PACSystems RX3i PROFINET Scanner Manual, GFK-2737.
IC695PNS001-ABAC PROFINET Scanner Module
5
GFK-2738C
Normal Operation of Individual LEDs
The PNS’s LEDs can operate in tandem to indicate fatal error, module location/identification, microprocessor
over temperature, and update conditions. For details on these blink patterns, refer to PACSystems RX3i
PROFINET Scanner Manual, GFK-2737.
OK LED
The OK LED indicates whether the module is able to perform normal operation.
Green, on
OK
Off
Not OK
LAN LED
The LAN LED indicates access to and activity on the Ethernet network. The LAN LED indicates network
packets are being processed by the network interface (not just passing through the embedded switch).
Blinking on
The module’s network interface is active
Off
No activity
STATUS LED
The STATUS stays Green during normal operation.
Green, on
Normal Operation
Red, blinking
A MAC address read from nonvolatile memory is invalid. Ports with invalid
MAC addresses remain disconnected from the Ethernet network.
CONN LED
The CONN LED indicates the status of PROFINET connections.
Green, on
At least one PROFINET connection (AR) exists with an IO-Controller.
Amber, blinking
No device name configured.
Off
No PROFINET connection (AR) exists.
Port LEDs
The PROFINET Controller has four Port LEDs, PORT1, PORT2, PORT3, and PORT4 that indicate link
speed, link connection and link activity corresponding to the four possible external Ethernet ports.
Blue, on
Link connected, 1000 Mbps
Blue, blinking
Port active, 1000 Mbps
Green, on
Link connected, 100 Mbps
Green, blinking
Port active, 100 Mbps
Purple, on
Link connected, 10 Mbps
Purple, blinking
Port active, 10 Mbps
Off
The associated Ethernet port is not connected to an active link
Red, on
Port 3 and port 4 only. Incompatible SFP plugged into port.
6
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
ACTIVE LED
The active LED indicates the Scanner is connected to a PROFINET IO Controller that is controlling the IO
data for the PNS’s IO modules.
Green, on
PNS is connected to a PROFINET IO-Controller that is controlling IO Module
IO data.
Off
PNS is not connected to a PROFINET-IO Controller.
USB LED
The USB LED indicates activity on the USB port.
Green, on
A USB cable is connected.
Green, blinking
USB port activity
Off
No USB port activity
Quick Start Guide
Installation and initial startup procedures for the PNS include the following steps. Before installing and
operating the PNS, refer to the PACSystems RX3i PROFINET Scanner Manual, GFK-2737 for detailed
information.
1. Pre-Installation check
Upon receiving your RX3i equipment, carefully inspect all shipping containers for damage. If any part of the
system is damaged, notify the carrier immediately. The damaged shipping container should be saved as
evidence for inspection by the carrier.
As the consignee, it is your responsibility to register a claim with the carrier for damage incurred during
shipment. However, GE Intelligent Platforms will fully cooperate with you, should such action be necessary.
After unpacking the RX3i equipment, record all serial numbers. Serial numbers are required if you should
need to contact Customer Care during the warranty period. All shipping containers and all packing material
should be saved should it be necessary to transport or ship any part of the system.
2. Installing the PNS in an RX3i backplane
The Scanner can be installed in slot 1 or 2 of a 7, 12, or 16-slot RX3i Universal Backplane, or in slot 6 of a
7-slot RX3i Universal Backplane. The installation slot must match the slot that is selected in the module’s
hardware configuration.
The back of the PNS has an exposed heat sink and backplane connector. Before inserting the module into
the backplane, the removable conduction cooling cover must be removed from backplane.
Removable plastic for the
module’s heat-sink.
TB 1
E
X
P
A
N
S
I
O
N
1
8
0
1
2
3
4
5
6
7
8
9
10
11
12
IC695PNS001-ABAC PROFINET Scanner Module
7
GFK-2738C

RX3i rack power must be turned off. The PNS
does not support insertion/removal while
power is applied to the system (hot swap).

Holding the module firmly, align the module
with the correct slot and connector.

Engage the module’s rear pivot hook in the
notch on the top of the backplane (1).

Swing the module down (2) until the module’s
connector engages the backplane’s backplane
connector.

Visually inspect the module to be sure it is
properly seated.

Secure the bottom of the module to the
backplane using the machine screws provided
with the module (3).

Tighten the heat sink screw on the front of the
module in the threaded hole in the backplate
to 6 in-lbs, using a flat-tip screwdriver.
1
2
3
3. Connecting the PNS to the PROFINET network and to a 10BaseT, 100BaseTX or 1000BaseT
IEEE 802.3 network for general Ethernet communications
Caution
Do not connect two or more ports on the PNS to the same device, either directly or indirectly.
Each port on an RX3i PNS operates independently, so devices that operate at different speeds and/or duplex
modes may be attached to the ports. By default, all ports, including empty, unconfigured SFP cages, are set
for Automatic, which enables auto-negotiation for the widest range of options supported by the port. For other
options, refer to the user’s manual, GFK-2737.
Bottom of module
Port 1
Port 3
Front
Port 2
Port 4
8
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
4. Installing SFP devices
Warning
Optical SFPs use an invisible laser to generate a fiber-optic signal. Always keep the port
covered if a cable is not installed. Do not look into the open port if a cable is not installed.
Warning
If the surrounding air operating temperature of the PNS is greater than 40 °C,SFP devices
could have operating temperatures over 70 °C (158 °F). Under these conditions, for your
safety, do not use bare hands to remove an SFP device from the SFP cage. Use protective
gloves or a tool (needle-nose pliers) to avoid handling the hot SFP device directly when
removing the SFP device.
For a list of SFP module types and network cabling details, refer to “SFP Modules for Ethernet Ports” in the
PACSystems RX3i PROFINET Scanner Manual, GFK-2737.
5. Installing the USB port driver (optional)
The PNS provides a micro USB port for connection to a computer running Windows 2000, Windows XP,
Windows Vista, or Windows 7 operating system. The USB port is used only for firmware updates. USB driver
files are provided as part of upgrade packages compatible with the PROFINET Scanner. The PNS includes a
driver-install application that can be used to enable a computer to communicate with a PNS via its USB port.
6. Assigning an IO Device Name to the PNS
Before attempting to connect to or configure the RX3i PNS, the IO Device Name must be set with a Discovery
and Configuration Protocol (DCP) tool, such as the Proficy Machine Edition Discovery Tool.
7. Configuring the PNS and its IO Modules on a PROFINET network
Proficy Machine Edition is the primary tool used to configure an RX3i PROFINET network. The PNS must be
installed in the slot that is selected in the module’s hardware configuration. The GSDML file for the RX3i PNS
rd
is included with Proficy Machine Edition. To obtain the GSDML for import into a 3 -Party tool, contact GE
Technical Support.
IC695PNS001-ABAC PROFINET Scanner Module
9
GFK-2738C
Supported Modules, Power Supplies and Backplanes,
The following modules can be used with this release of the RX3i PROFINET Scanner IO-Device:
Catalog Number
Module Description
Distinguishing
1
Classes
Discrete Input Modules
1
IC693ACC300
Input Simulator Module (8pt & 16pt operation)
IC693MDL230
8 Circuit Input 120 VAC Isolated
8 in, 16 in
IC693MDL231
8 Circuit Input 240 VAC Isolated
8 in
IC693MDL240
16 Circuit Input 120 VAC
16 in
IC693MDL241
16 Circuit Input 24 VAC / VDC
16 in
IC693MDL250
16 Circuit Isolated Input 120 VAC, Input Filtering Off
16 in
IC693MDL250
16 Circuit Isolated Input 120 VAC, Input Filtering On
none
IC693MDL260
32 Circuit Input 120 VAC, Input Filtering Off
32 in
IC693MDL260
32 Circuit Input 120 VAC, Input Filtering On
32 in/out
IC693MDL632
8 Circuit Input 125 VDC Positive / Negative Logic
IC693MDL634
8 Circuit Input 24 VDC Positive / Negative Logic
8 in
IC693MDL635
16 Circuit Input 125 VDC Positive / Negative Logic
16 in
IC693MDL645
16 Circuit Input 24 VDC Positive / Negative Logic
16 in
IC693MDL646
16 Circuit Input 24 VDC Positive / Negative Logic Fast
16 in
IC693MDL648
16 Circuit Input 48 VDC Positive / Negative Logic Fast
16 in
IC693MDL654
32 Circuit Input 5/12 VDC Positive / Negative Logic
32 in
IC693MDL655
32 Circuit Input 24 VDC Positive / Negative Logic Fast
32 in
IC693MDL660
32 Circuit Input 24 VDC Positive / Negative Logic, Input Filtering Off
32 in
IC693MDL660
32 Circuit Input 24 VDC Positive / Negative Logic, Input Filtering On
32 in/out
IC694ACC300
Input Simulator Module (8pt& 16pt Mode)
8 in, 16 in
IC694MDL230
8 Circuit Input 120 VAC Isolated
8 in
IC694MDL231
8 Circuit Input 240 VAC Isolated
8 in
IC694MDL240
16 Circuit Input 120 VAC
16 in
IC694MDL241
16 Circuit Input 24 VAC / VDC
16 in
IC694MDL250
16 Circuit Input 120 VAC Isolated
none
IC694MDL260
32 Circuit Input 120 VAC
none
IC694MDL632
8 Circuit Input 125 VDC Positive / Negative Logic
8 in
IC694MDL634
8 Circuit Input 24 VDC Positive / Negative Logic
8 in
IC694MDL635
16 Circuit Input 125 VDC Positive / Negative Logic
16 in
IC694MDL645
16 Circuit Input 24 VDC Positive / Negative Logic
16 in
IC694MDL646
16 Circuit Input 24 VDC Positive / Negative Logic Fast
16 in
IC694MDL654
32 Circuit Input 5/12 VDC Positive / Negative Logic
32 in
IC694MDL655
32 Circuit Input 24 VDC Positive / Negative Logic Fast
32 in
IC694MDL658
32 Circuit Input 48 VDC Positive / Negative Logic Fast
32 in
IC694MDL660
32 Circuit Input 24 VDC Positive / Negative Logic
none
IC695MDL664
16 Circuit Smart Input 24VDC Positive Logic
8 in
2
8 in
none
The PNS cannot distinguish between modules within the same Distinguishing Class type. This means that any module
physically present that is within the same class as the one configured will not alert the user with a System Configuration
Mismatch fault on the Controller Fault Table. See GFK-2222 Chapter 3 for CPU operation during System Configuration
Mismatch faults.
2
The PNS currently does not support “Fault Reporting” from this module.
10
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
Catalog Number
Distinguishing
1
Classes
Module Description
Discrete Output Modules
IC693MDL310
12 Circuit Output 120 VAC 0.5A
16 out
IC693MDL330
8 Circuit Output 120/240 VAC 2A
8 out
IC693MDL340
16 Circuit Output 120 VAC 0.5A
16 out
IC693MDL350
16 Circuit Output 120/240 VAC Isolated
16 out
IC693MDL390
5 Circuit Output 120/240 VAC 2A Isolated
8 out
IC693MDL730
8 Circuit Output 12/24 VDC 2A Positive
8 out
IC693MDL731
8 Circuit Output 12/24 VDC 2A Negative
8 out
IC693MDL732
8 Circuit Output 12/24 VDC 0.5A Positive
8 out
IC693MDL733
8 Circuit Output 12/24 VDC 0.5A Negative
8 out
IC693MDL734
6 Circuit Output 125 VDC 1A Positive/Negative
8 out
IC693MDL740
16 Circuit Output 12/24 VDC 0.5A Positive
16 out
IC693MDL741
16 Circuit Output 12/24 VDC 0.5A Negative
16 out
IC693MDL742
16 Circuit Output 12/24 VDC 1A Positive
16 out
IC693MDL748
8 Circuit Output 48 VDC 0.5A Positive
8 out
IC693MDL752
32 Circuit Output 5/24 VDC 0.5A Negative
32 out
IC693MDL753
32 Circuit Output 12/24 VDC 0.5A Positive
IC693MDL754
32 Circuit Output 24 VDC 0.75A Positive
Diagnostics Off
32 out
IC693MDL754
32 Circuit Output 24 VDC 0.75A Positive
Diagnostics On
32 in/out
IC693MDL760
Solenoid Valve Output Module
16 out
IC693MDL916
16 Circuit Output 4A Relay
16 out
IC693MDL930
8 Circuit Output 4A Relay Isolated
8 out
IC693MDL931
8 Circuit Output Relay Form BC Isolated
8 out
IC693MDL940
16 Circuit Output 2A Relay
16 out
IC694MDL310
12 Circuit Output 120 VAC 0.5A
16 out
IC694MDL330
8 Circuit Output 120/240 VAC 2A
8 out
IC694MDL340
16 Circuit Output 120 VAC 0.5A
16 out
IC694MDL350
16 Circuit Output 120/240 VAC Isolated
none
IC694MDL390
5 Circuit Output 120/240 VAC 2A Isolated
8 out
IC694MDL732
8 Circuit Output 12/24 VDC 2A Positive
8 out
IC694MDL734
6 Circuit Output 125 VDC 1A Positive/Negative
8 out
IC694MDL740
16 Circuit Output 12/24 VDC 0.5A Positive
16 out
IC694MDL741
16 Circuit Output 12/24 VDC 1A Negative
16 out
IC694MDL742
16 Circuit Output 12/24 VDC 1A Positive
16 out
IC694MDL752
32 Circuit Output 5/24 VDC 0.5A Negative
32 out
IC694MDL753
32 Circuit Output 12/24 VDC 0.5A Positive
32 out
IC694MDL754
32 Circuit Output with ESCP
none
IC694MDL916
16 Circuit Output 4A Relay
none
IC694MDL930
8 Circuit Output 4A Relay Isolated
8 out
IC694MDL931
8 Circuit Output Relay Form BC Isolated
8 out
IC694MDL940
16 Circuit Output 2A Relay
16 out
IC695MDL765
16 Circuit Smart Output 24/125 VDC 2A Positive Logic
IC693MAR590
8 Circuit Mixed 120 VAC Input / Relay Output
8 in/out
IC693MDR390
8 Circuit Mixed 24 VDC Input / Relay Output
8 in/out
32 out
2
none
Discrete Mixed Modules
IC695PNS001-ABAC PROFINET Scanner Module
11
GFK-2738C
Catalog Number
Module Description
Distinguishing
1
Classes
Analog Input Modules
IC693ALG220
4 Point Analog Voltage Input
ALG IN 4
IC693ALG221
4 Point Analog Current Input
ALG IN 4
IC693ALG222
16 Point Analog Voltage Input
ALG IN 16
IC693ALG223
16 Point Analog Current Input
ALG IN 16
IC694ALG220
4 Point Analog Voltage Input
ALG IN 4
IC694ALG221
4 Point Analog Current Input
ALG IN 4
IC694ALG222
16 Point Analog Voltage Input
ALG IN 16
IC694ALG223
16 Point Analog Current Input
ALG IN 16
3
IC695ALG616
16 Point Analog Current / Voltage Input
none
IC693ALG390
2 Point Analog Voltage Output
ALG OUT 2
IC693ALG391
2 Point Analog Current Output
ALG OUT 2
IC693ALG392
8 Point Analog Current / Voltage Output
ALG OUT 8
IC694ALG390
2 Point Analog Voltage Output
ALG OUT 2
IC694ALG391
2 Point Analog Current Output
ALG OUT 2
IC694ALG392
8 Point Analog Current / Voltage Output
IC695ALG708
8 Point Analog Current / Voltage Output
Analog Output Modules
ALG OUT 8
3
none
Analog Mixed Modules
IC693ALG442
4 Input / 2 Output, Current / Voltage
IC694ALG442
4 Input / 2 Output, Current / Voltage
ALG IN 4, ALG
OUT 2
ALG IN 4, ALG
OUT 2
RTD Input Modules
IC695ALG508
8 Channel Isolated RTD Input
3
none
Power Supply Modules
IC695PSA040
Universal 120/240 VAC, 125VDC 40W Power Supply
none
IC695PSA140
Multifunctional 120/240 VAC, 125VDC 40W Power Supply
none
IC695PSD040
24VDC 40W Power Supply
none
IC695PSD140
Multifunctional 24VDC 40W Power Supply
none
Small Form-factor Pluggable (SFP) Modules
IC695SPC100
10/100/1000Base-T Copper SFP
none
IC695SPF002
100Base-FX (fiber 2km) SFP
none
IC695SPF010
1000Base-LX (fiber 10km) SFP
none
IC695SPF550
1000Base-SX (fiber 550m) SFP
none
The RX3i PROFINET Scanner can be used in the following PACSystems backplanes:
Catalog Number
3
Backplane Type
IC695CHS007
7 Slot RX3i Universal Backplane
IC695CHS012
12 Slot RX3i Universal Backplane
IC695CHS016
16 Slot RX3i Universal Backplane
4
The PNS currently does not support “Fault Reporting” or “Interrupts” from this module.
The PNS cannot distinguish between the different rack sizes. Choosing the wrong type will not generate a System
Configuration Mismatch fault on the Controller Fault Table.
4
12
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
Release History
Version
Firmware
Revision
Date
Comments
IC695PNS001-ABAC
1.10
July 2013
Support for additional RX3i I/O modules, listed in
“New Features and Enhancements in this
Release” on page 13.
IC695PNS001-ABAA
1.00
June 2013
Hardware update for improved manufacturability.
No changes to features, functions or compatibility
IC695PNS001-AAAA
1.00
March 2013
Initial release.
Important Product Information for this Release
Compatibility
The following CPU firmware, programming software and backplane hardware versions are required to use the
features introduced in the PNS release:
Controller CPU firmware
CPU315/CPU320 firmware version 7.10 or later
CPE305/CPE310 firmware version 7.10 or later
RXi Controller firmware version 7.80 or later
Programmer software
Proficy Machine Edition version 8.0 or later
RX3i PROFINET Controller
IC695PNC001 with firmware version 1.20 or later
RX3i backplane hardware
The following minimum backplane hardware revision must be used:
IC695CHS012-BAMP
IC695CHS016-BAMP
IC695CHS012CA-BAMP
IC695CHS016CA-BAMP
or
IC695CHS012-CA (or later)
IC695CHS016-CA (or later)
IC695CHS012CA-CA (or later)
IC695CHS016CA-CA (or later)
or
IC695CHS007-AA (or later)
When installing, operating, or maintaining the IC695PNS001, personnel must
insure any electrostatic charge is discharged through the use of a grounded
ESD strap or other means. This requirement does not apply if the
IC695PNS001 is used with the following backplane revisions:
IC695CHS012-EA (or later)
IC695CHS016-EA (or later)
IC695CHS012EA-CA (or later)
IC695CHS016EA-CA (or later)
or
IC695CHS007-BA (or later)
Small form-factor pluggable modules
IC695SPC100A or later
IC695SPF002A or later
IC695SPF550A or later
IC695SPF010A or later
RX3i modules
For a complete list, refer to “Supported Modules, Power Supplies and
Backplanes,” on page 9.
IC695PNS001-ABAC PROFINET Scanner Module
13
GFK-2738C
New Features and Enhancements in this Release
Release 1.10 adds support for the following RX3i modules:

IC695MDL664 (16 Circuit Smart Input 24VDC Positive Logic)
Operational Notes:
o Options related to “Fault Reporting” are not currently supported.
o Configuration rule checking is performed by the PROFINET Scanner at PROFINET connection
time. Rule check failures will transition the module to default operation and point faults energized
for assigned I/O. (See the PACSystems RX3i PROFINET Scanner Manual, GFK-2737A for
additional details.)

IC695MDL765 (16 Circuit Smart Output 24/125 VDC 2A Positive Logic)
Operational Notes:
o Options related to “Fault Reporting” are not currently supported.
o Output Command Feedback data is not currently supported.
o Configuration rule checking is performed by the PROFINET Scanner at PROFINET connection
time. Rule check failures will transition the module to default operation and point faults energized
for assigned I/O. (See the PACSystems RX3i PROFINET Scanner Manual, GFK-2737A for
additional details.)

IC695ALG508 (8 Channel Isolated RTD Input)

Operational Notes:
o Options related to “Fault Reporting” are not currently supported.
o Options related to “Interrupts” are not currently supported.
o Options related to “Rate of Change” are not currently supported.
o Configuration rule checking is performed by the PROFINET Scanner at PROFINET connection
time. Rule check failures will transition the module to default operation and point faults energized
for assigned I/O. (See the PACSystems RX3i PROFINET Scanner Manual, GFK-2737A for
additional details.)
IC695ALG616 (16 Channel Analog Input Current / Voltage)
Operational Notes:
o Options related to “Fault Reporting” are not currently supported.
o Options related to “Interrupts” are not currently supported.
o Options related to “Rate of Change” are not currently supported.
o Configuration rule checking is performed by the PROFINET Scanner at PROFINET connection
time. Rule check failures will transition the module to default operation and point faults energized
for assigned I/O. (See the PACSystems RX3i PROFINET Scanner Manual, GFK-2737A for
additional details.)

IC695ALG708 (8 Channel Analog Output Current / Voltage)
Operational Notes:
o Options related to “Fault Reporting” are not currently supported.
o Options related to “Interrupts” are not currently supported.
o Output Command Feedback Reference data is not currently supported.
o Configuration rule checking is performed by the PROFINET Scanner at PROFINET connection
time. Rule check failures will transition the module to default operation and point faults energized
for assigned I/O. (See the PACSystems RX3i PROFINET Scanner Manual, GFK-2737A for
additional details.)
14
IC695PNS001-ABAC PROFINET Scanner Module
GFK-2738C
Problems Resolved by this Revision
Subject
Description
Loss of IO During Hot insertion of I/O
module
In earlier versions, while hot inserting an I/O Module, the PNS could disable
outputs on other Output Modules in the rack to their Default/Hold Last State
operation and mark Input Module data as bad in PROFINET messages back
to the IO-Controller. (For GE-IP controllers, this is represented as IO Point
Fault contacts.) This could occur for up to 5ms and then I/O continued
normally.
RX3i PNS names starting or ending
with a hyphen not prevented from
storing to the RX3i PNS from an
SD Card
PROFINET specifies that IO Device names should neither start nor end with
a hyphen. Previous releases did not prevent names starting or ending with a
hyphen from being stored to the RX3i PNS from the SD Card.
Restrictions and Open Issues in this Release
Subject
Description
PROFINET connection losses with
MRP enabled and IO update rates of
1 ms
Applications with MRP Ring network topologies and IO Devices configured
with IO Update Rates of 1 ms on either 100 Mbps or 1000 Mbps may
encounter PROFINET Connection Losses of PROFINET IO Devices during a
ring-break event. Use of MRP with 1 ms IO Update rates is not recommended
with this release. Refer to “Media Redundancy Protocol Support” in the
PACSystems RX3i PROFINET Scanner Manual, GFK-2737, for details on
recommended MRP configurations.
Connecting Ethernet ports not
configured as ring ports to the MRP
ring may inhibit ring-break detection
In order to insure correct MRP ring-break detection, it is important to connect
the correct Ethernet ports of the RX3i PNS to the MRP ring. The ports
connected to the ring must be the same ports configured as MRP Ring Ports.
Failure to connect the configured ports will prevent the PNS from correctly
participating in the MRP ring, may inhibit ring-break detection, and may result
in losses of IO Devices upon ring-break events. It is recommended during
system commissioning that the physical network connections be verified with
the system configuration for ring ports in system’s hardware configuration.
Refer to “Media Redundancy Protocol Support” in the PACSystems RX3i
PROFINET Scanner Manual, GFK-2737, for details on recommended MRP
configuration.
More than three
ALG508/ALG616/ALG708 modules in
a PNS rack cause system to transition
to STOP/FAULTED during store of
hardware configuration
IC695ALG508, IC695ALG616, IC695ALG708 modules have larger
configurations than other modules. If more than three of these modules are
placed in a PNS rack, an IOC Software Fault - Module Firmware Fault could
be generated on the RXi Controller (v7.80 or earlier) or RX3i PNC (v1.22 and
earlier). If this happens, the system will go to STOP/FAULTED state. Future
versions of the RXi Controller and IC695PNC001 firmware will remove this
restriction.
With the current PNC or RXi firmware, you must limit the number of ALG508,
ALG616, and ALG708 modules to three in a single PNS rack to avoid this
issue. This limit does NOT apply to the main PLC rack.
IC695PNS001-ABAC PROFINET Scanner Module
15
GFK-2738C
Operational Notes
Subject
Description
IOPS of power supplies do not update
when power supply is switched off
The IOPS (status) of a power supply is marked good or bad at the start of
each PROFINET IO connection. The IOPS is not updated when the power
supply is turned on and off.
RX3i PNS allows firmware update
while connected to a running
PROFIENT IO Controller
The RX3i PNS does not prevent initiation of module Firmware Update via
Winloader if it is actively connected to an IO Controller. Do not initiate
Firmware Update of an RX3i PNS until you have placed its controlling
PROFINET IO Controller into Stop mode (no longer driving output and
collecting inputs from the RX3i PNS).
Port LED for Ethernet ports configured
to 100 Mbps may briefly flash blue
before changing to green
During power-up, the Port LEDs of the RX3i PNS Ethernet ports configured
for 100 Mbps operation may briefly flash blue before turning green. The port
remains configured for 100 Mbps operation during the power-up process and
afterwards.
PROFINET Alarms are not supported
PROFINET Alarms are not issued from the RX3i PNS in this release.
Some power supplies use two
backplane slots, but this is not
indicated in the change module list
interface of HWC
Note that the IC695PSA040 and IC695PSA140 each utilize two backplane
slots, but are shown using only one slot in the Change Module List interface
for the RX3i PNS. Configuring a module for the already utilized slot will result
in a Loss of I/O Module fault.
The PNS module is supported only in
certain backplane slots.
The RX3i PROFINET Scanner module is configurable for use in Slot 1, Slot 2,
and when installed in the IC695CHS007 backplane, also Slot 6.
Explore PROFINET Networks tool not
supported on submodules
The Proficy Machine Edition Explore PROFINET Networks tool does not
return submodule information for IO modules within its RX3i rack in this
release. Submodule information for the RX3i PNS itself is returned.
SFP modules do not support hot swap
In this release of the RX3i PNS, SFP modules do not support hot swap. This
means that if an SFP module is hot-inserted into the RX3i PNS, no Fault
Table entry will be logged and configuration parameters will not be applied to
the SFP until the RX3i PNS is power cycled. Until the RX3i PNS is power
cycled, the SFP will remain enabled and active with auto negotiation
turned on.
IO modules hot inserted while an
invalid configuration is stored require
re-insertion or power cycle to recover
If an invalid configuration for an IO module in the PNS is stored to the CPU,
such as a default value outside the engineering units range, and the IO
module using that configuration is hot inserted in the PNS, the hot insertion
process fails. No Addition of IO Module fault is generated and the module is
left at its default operation. The configuration of that module will not be retried
until the module is re-inserted or the PNS rack is power cycled, even if the
configuration is corrected in the CPU.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement