Paladin 1724X3 pro - SC 28.X3 pro Owner Manual
Paladin 1724X3 pro - SC 28.X3 pro
is a time switch with an astro function that allows you to switch the whole year through in relation to sunset and sunrise, e.g., for illumination purposes (astro-ON with sunset and astro-OFF with sunrise). The programming is made according to regular switching times with the following difference: Choose astro function astro ON and astro OFF, respectively. While programming an astro program step, there will be no time (hh:mm) suggested. Instead you have the possibility to enter an offset. E.g., if you like to switch on the light 20 minutes before sunset, you would enter an offset of minus 20 minutes while programming astro ON.
Advertisement
Advertisement
Instruction Manual
GB
Time switch with Astro function
Connection diagram
3. Menu overview
Directory
1. Safety instructions
2. Initial operation
3. Menu overview
4.
Symbol legend
5. Key function
6. Handling advice
7. Channel ON OFF / Permanent P
8. New Program
9. Example „New Program“
10. Astro-function
11. Astro-adjustments
12. Program permanent
13. Additional adjustments
13. Reset-Function
14. Program modify
1. Safety instructions
!
The installation and assembly of electrical equipment must be only carried out only by a skilled
Person! Otherwise fire danger or danger of an electric shock exists!
!
Connect the supply voltage/frequency as stated on the product label!
!
Warranty void if housing opened by unauthorised person!
!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if external influences exceed certain limits!
SC 28.X3 pro 172 4X3 pro
2. Initial operation
The time switch is delivered in sleep-mode, the display is switched off.
Press -button for 1 second.
The current date and time is already programmed and European daylight savings time is activated.
Select the desired language by pressing -buttons and confirm it by pressing .
(Remark: By pressing you move one step backwards from the current position)
If required, date, time and daylight savings time mode can be adjusted also by pressing
-buttons and a subsequent confirmation with .
When using the astro function it is obligatory to enter the geographical position of the place of the installation of the device. Choose with -buttons between „location“ (pre-defined cities) and „position“ (longitude and latitude). Confirm your choice again with . (The easiest way is choosing a pre-defined city within the „locations“-menu.)
Enter the nearest city or the geographical coordinates with -buttons and confirm with
4. Symbol legend
Channel is switched ON
Channel is switched OFF
For the current date the “holiday program” / “permanent by date” is activated
Standard programming step
Current state is based on a manual over-ride. The state will be cancelled with the next programming step.
Current state is based on a manual over-ride. The state is permanent until terminated manually (7).
Days of the week Monday, Tuesday, ... Sunday;
The underscores indicate if the program is active for the days above.
Element within sub-menu “program delete”
Astro function: Current state is based on a sunrise or sunset taking into account an optionally adjusted
Offset (10 / 11).
5. Key function
1. To access the Enter-mode (program, adjustments, options) from the automatic-mode.
2. To revert to the beginning of the current (sub-) menu.
1. To adjust the flashing digit.
2. To scroll through a choice
1. Automatic-mode: To switch the channel ON or OFF until the next programming step occurs.
2. Automatic-mode: A push longer than 3 sec. = Permanent switching status (7).
The time switch is locked; to unlock the device the PIN has to be entered (13).
6. Handling advice
The time switch is programmable without external power supply after pressing the -button.
To revert one step or one level back while in the Enter-Mode press .
After completion of a (sub-) menu confirming end
will return the device into the automatic-mode.
With the choice changes from end
to continue
. By confirming continue
the time switch returns to the beginning of the current
(sub-) menu.
When confirming end
before completion, the time switch returns to the automatic-mode without saving the entered data.
7. Channel
ON OFF
/ Permanent P
Channel
ON OFF
By pushing -buttons ( -buttons) a manual switch of the channels take place. The resulting switching status is marked with the hand-symbol and remains until the next programming step occurs. (temporary over-ride)
Permanent switching status P
By pressing the corresponding channel button for more than 3 sec. the channel is permanently switched ON or OFF.
The status remains until the next manual switching occurs (> 3 sec.). (permanent over-ride)
1. To activate the time switch when operated without power supply.
2. To confirm the selection or the entered data.
8. New Program (See also the example (9))
Step A. to C. please refer to point 9. (Example “New Program”)
9. Example „New Program“ (For a regular switching time)
A.
If power supply is disconnected press for one second. The display appears in Automatic-Mode.
B.
Press , the time switch is now in the Enter-Mode.
C.
Confirm
Program
with .
D.
Confirm new program
with .
E.
Choose the desired channel with and confirm with .
F.
For regular switching times choose switching times on
or off
with -buttons and confirm with . (The astro astro ON
or astro OFF
please refer to point 10)
G.
Within this level you activate the days of the week (1…7) on which the switching time should happen.
With you activate “yes” or deactivate “no” the corresponding date. Confirm each day with .
H.
Adjustment of the time: Hours and . Minutes and .
I.
Verify the entered switching time: If the flashing summary of the programming step is correct, verify on or off with . After verification you have the choice between edit/delete
and end
with .
10. Astro-function
Program
-> new program
-> channel A/or B
->
…
The astro function allows you to switch the whole year through in relation to sunset and sunrise, e.g. for illumination purposes ( with sunrise). astro-ON
with sunset and astro-OFF
The programming is made according to (8 / 9) with following difference:
Choose astro function astro ON and astro OFF respectively (9F).
While programming an astro program step there will be no time (hh:ss) suggested
(8H / 9H). Instead of this you have the possibility to enter an like to switch on the light 20 minutes before sunset would you enter an minus 20 minutes while programming astro ON
. offset
. E.g. if you offset
of
11. Astro-adjustments
Adjustment
->
Astro
->
…
Block Sunset:
J.
If you want to proceed with programming, confirm
To leave the programming menu confirm end
. next switching
with .
The following options concerning the astro function are adjustable to satisfy your needs:
Position location:
Adjust your geographical position with pre-defined choice of regions/countries and cities.
Position coordinates:
Adjust your geographical position with longitude, latitude and time zone.
Block Sunrise:
Earliest possible point in time for the astro function (sunrise).
Latest possible point in time for the astro function (sunset), e.g. switching on the light not later than 10 p.m. even if sunset is later.
12. Program permanent
Program
-> new program
-> channel A/B
-> permanent
->
…
One permanent by date programming step (holiday function) for each channel is possible. During the desired period (The function is valid for the
( whole days) the channel can be switched off ( permanent on
). permanent off
) or on
The programming of this function is as described in (8 / 9).
The choice permanent
will not be offered anymore within the menu new program
when already in use. The switching time can be modified and deleted within respectively.
Program modify
(14) and
Program delete
(13)
13.
Additional adjustments
Menu Main menu
Program query
Program copy
Application
Program To query the programming steps and remaining memory locations
Program
Copy from one channel to another. Memory of the channel won’t be overwritten; the copied switching steps appear additionally.
!
Permanent by date function is not copied!
14. Program modify
Program
->
Program modify
->
…
Program delete
Program
Deletion of switching time(s). The program for all channels, single channels and single programming steps within on channel can be deleted.
Date-Time
Summertime
Adjustment Adjustment of date and time
Adjustment Adjustment of the daylight saving time mode (ON/OFF)
Language
Factory Defaults
Adjustment Choice of languages
Adjustment
Reset to the state of delivery. Date, time and switching program will be lost!
Within
Program modify
each single switching time can be modified.
Counter
PIN-Code
Reset-Function
Options
Options
Displays the hour counter and pulse counter for each channel and the time switch itself.
The time switch can be locked with a 4-digit PIN-Code. The code can be adjusted, activated and deactivated. If you have forgotten the Code please call customer service.
Press all front keys for 2 seconds. The time switch is reset. The values for date and time will be deleted and have to be re-entered. The switching program has not been deleted!
www.hugo-mueller.de
BA SC28X3pro-1724X3pro MP; DE, GB, FR, IT - 22347 - 2007.11-05

Public link updated
The public link to your chat has been updated.
Advertisement