Mytee Products, Inc. Deluxe Prep Center - Auto Detailer

Mytee Products, Inc. Deluxe Prep Center - Auto Detailer
Instructions for
20-110 Deluxe Prep-Center™
Please read before use.
Model #
Serial #
Form # ADM-20 -110
6-09
13655 Stowe Dr., Poway, Ca. 92064
ENGLISH
FRONT
BACK
1
7
2
6
8
5
11
3
9
4
1. On Board Chemical Storage
2. Control Panel
3. Chemical Dispensers (x4)
4. Chemical Bottle Access Panel
5. Vacuum Inlet
6. Solution Inlet
7. On Board Tool Storage
8. Shop Air Hook Up
9. Tank Access Panel
10. 12” Rear Wheels
11. Vacuum Blower Outlet
10
ACCESSORIES
8400 - 3” Stainless
Steel Upholstery Tool
H375 - Hose Hanger (x2)
H369 - 25’ Dry Vac Hose
8100 - 25’ Vac/Sol Hose
PC86 - Crevice Tool
PC87 - Dry Claw
PC88 - Window Attachment
A919 - Blower Attachment
PUMP
M
CUU
VA
HEATER
P
PUM
TER
HEA
UM
U
VAC
After the machine has been plugged into a 20 amp grounded
outlet. Turn on pump. Key tool until upholstery tool releases a
steady flow.
VACUUM MOTOR
UM
U
VAC
P
PUM
P
PUM
TER
HEA
Release tool trigger. Turn on heater. Wait 8 – 10 minutes for unit
to pre-heat. Once heated, re-key upholstery tool until hot water
begins flowing. Once hot water is flowing, release trigger and preheat an additional 4 – 5 minutes.
AIR INLET PRESSURE REGULATOR
TER
HEA
Turn on vacuum motor and begin cleaning. For best results
make two dry passes to every wet pass.
Use the regulator to control the PSI of your shop air compressor
between 0 – 40 PSI.
CHEMICAL DISPENSING
Four individual chemical bottles. Bottles are powered by an
external compressed air source (not included).
TANKS
1
COMPRESSED AIR INLET
Inlet for shop air connection. Unit will regulate shop air to
proper PSI.
VACUUM INLET
2
1. Vacuum recovery tank – empty when full, keep filter and ball
float clean.
2. Solution tank – fill with fresh water and cleaning solution.
Hook up vacuum recovery hose to vacuum inlet.
ENGLISH
SOLUTION OUTLET
Solution quick connect. Hook up solution hose here.
BLOWER OUTLET
Hook up blower hose for vehicle drying.
AIR OUTLET
Pneumatic compressed air quick connect, 40 PSI max
outlet pressure.
TOP TRAY
On board tool and chemical storage.
Dear Customer:
Unpacking the Machine
Keep in mind that 20-110 Deluxe Prep -Center™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the 20-110 will give quality performance for many years to come.
Caution and Warnings
Congratulations on the purchase of your new 20-110 Deluxe Prep -Center™. As you
are already aware, the scene of the equipment world is becoming more high tech,
and we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a
freight damage claim.
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or death.
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Is used to call attention to a situation that could cause severe personal injury.
Grounding Instructions
This machine must be grounded when being recharged. If it should malfunction or
breakdown, grounding provides a path of least resistance for electrical shock. This
machine is equipped with a cord having an equipment-grounding conductor and
grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed in accordance with all local code and ordinances. Do not remove ground
pin; if missing, replace plug before use.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualified electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Parts and Service
Figure 2
Tab for Grounding
Screw
Figure 3
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where flammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with a solidstate speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Filling the Solution Tank
1. Fill the solution tank with the approved cleaning solution.
2. Do not fill up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70oC/160oF.
Use only non-flammable liquid in this machine.
Setup
1. Remove vacuum tank, then fill solution tank. Fill solution with water or approved
cleaning agent. For best results, fill with warm water (140o). Replace vacuum tank.
Flammable materials can cause an explosion or fire. Do not use flammable solutions
or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together firmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.
3. Attach other end of solution hose to wand.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.
6. Turn on pump. Key tool until you have a steady flow.
7. Release tool trigger. Turn on heater.
8. Wait 8 –10 minutes for unit to pre-heat.
9. Re-key upholstery tool until hot water begins flowing.
10. Once hot water is flowing, release trigger and pre-heat an additional 4–5 minutes.
11. Turn on vacuum motor.
12. Begin cleaning. Make two dry passes to every wet pass.
13. For floor cleaning, unplug tool and attach floor wand.
14. Work away from cords to avoid damage.
15. Use a defoamer in your recovery tank.
16. To clean heavily soiled areas, repeat cleaning from different directions.
17. When vacuum tank is full, empty tanks.
18. When work is complete, unplug cords and hoses.
19. Wrap and clean hoses. Clean all tanks.
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Perform machine setup procedures.
3. Inspect power cord for damage.
Operation
1. Turn pump switch on.
2. Pull up on tool lever to release air in the line. Hold lever until a steady flow of water
comes out of the wand.
3. Once pump is primed and there is pressure in the solution line, turn on heater switch
(if model is equipped with heater) and wait a few minutes for water to heat up.
4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When vacuum tank is full, it is time to empty the dirty water from the recovery tank,
and refill solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for five seconds after turning main power switch off.
After Use
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Remove recovery tank and empty. Clean filter.
5. Inspect solution filter. Clean or replace if damaged.
6. Store the machine in a clean, dry place.
7. Open recovery tank cover to promote air circulation.
8. Do not expose to rain. Store indoors.
Chemical Dispensing
The Prep Center comes standard with four chemical dispensing bottles. They are
powered by an air compressor (not included). Hook your shop air source to the rear
air inlet, and use the regulator on the front of the unit to adjust the air to desired
pressure (between 5 and 40 PSI.)
To fill:
1. Turn off or disconnect air compressor.
2. Pull trigger on one of the guns until all air in system is purged. IMPORTANT – If
this step is skipped bottle may be ejected or damaged while being removed. Bodily
injury could also result.
3. Open chemical tank door.
4. Unscrew tank from block.
5. Remove tank and fill with desired chemical.
6. Reinstall tank – you must make sure the top of the tank seals to the gasket in the
white block, or air will leak from the system. Improperly tightened bottles may be
ejected by the compressed air.
7. Close door, and re-activate compressed air.
To spray:
1. Select the gun that corresponds to the desired chemical.
2. Use twist cap on nozzle to adjust spray pattern and distance.
3. Pull trigger to spray.
Air Blower Attachment
The Prep Center features an air-blower on the control panel. Note that the vacuum
motor must be running for the blower to operate. Hook you blower hose to the blower
port, and then use the two provided tools for a variety of tasks:
Air purging:
Use the cone shaped nozzle to blow out vents, crevices, and more in the vehicle.
Interior drying:
Roll the included window attachment up in the window of the vehicle for hot air
interior drying.
Exterior drying:
Use the cone shaped attachment to dry windshields and body panels.
Maintenance Schedule
Maintenance item
Daily
Clean and inspect Tanks
Clean and inspect Hoses
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean float shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
Inspect machine for water leaks and loose hardware
x
x
x
x
Once a week
x
x
x
x
x
Trouble Shooting
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit.
3. If the wire from power cord has become disconnected from terminal block
reattach wire.
Pump does not work properly.
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s system maintainer.
6. If brass check valve is stuck replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate switch may need to be replaced.
9. If pump motor brushes are worn, replace pump.
10. If solution tank is empty, fill solution tank up with a premixed detergent.
11. If pump is pulsating, tighten all hoses. Check for leaks.
12. Bad pressure switch, replace with new pressure switch.
Heater does not work properly.
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
3. Worn out automatic sensor needs to be replaced with new sensor.
4. Replace switch if switch on switch plate is bad.
5. Reconnect heater wire if has become disconnected.
Vacuum motor does not work properly.
1. If switch on switch plate is bad, replace switch.
2. Connect hose tightly if hose is not connected tightly to upholstery tool or machine.
3. Clean upholstery tool if upholstery tool is clogged with hair, carpet fibers
and/or debris.
4. If vacuum tank lid is not on tightly, secure the vacuum tank lid on tightly.
5. If vacuum tank lid or the vacuum tank is cracked, replace lid or tank.
6. If vacuum hose is cracked or split, replace vacuum hose.
7. Empty the vacuum tank of all wastewater if ball float is shut off.
8. Replace vacuum motor if vacuum motor armature is worn out.
9. If water is coming out of the vacuum motor, use a low foaming detergent.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.
FAQs
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.
Q: How much does the 20- 110 weigh and what are the shipping dimensions?
A: 200 Pounds - Box dimensions are 42” x 48” x 58”. Must ship motor freight.
Q: What comes standard with the 20-110?
A: The 20 - 110 comes with 25’ Vacuum/Solution Hose (8100), 25’ dry vacuum hose
(H369), dry claw (PC87), crevice tool (PC86), window attachment (PC88), blower
attachment (A919), and four 25’ chemical dispensers with hoses and guns, interior
and exterior drying attachments with hose, a 3” Stainless Steel Upholstery Tool
(8400) and two hose hangers (H375).
Q: Where do I plug the machine in?
A: The 20 - 110 requires a 20A grounded circuit. Please note: GFI outlets may trip
before the breaker setting.
Q: What is the proper pre heat cycle for the 20-110?
A: Turn pump switch to the on position and prime pump through the solution hose
and the tool. Then turn the heater switch to the on position. Let the machine sit idle
for 8 -10 minutes. Spray tool until you feel the hot water from the jet. Let machine sit
idle for an additional 3 - 5 minutes. This will insure the water in the heater and hoses
will be at the hottest point to start cleaning.
Q: Are the pumps re-buildable for the 20-110?
A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.
Q: Is there anything I can do to increase the expected life of my machine?
A: Run a System Maintainer through the system to keep the hoses, pump, and
heater clean and free of debris.
Warranty
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this
lifetime limited warranty. This limited warranty begins on the date of the customer’s
purchase and is valid and available to the original purchaser with proof of purchase,
and is not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers
the cost of replacement or repair only and does not cover shipping or labor costs.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. “Wear parts” are items which wear out
as a result of usage or the passage of time and are consumed despite attempts to
maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,
hoses, switches, thermostats, plastisol parts, filters, bearings, brushes, solenoids, orings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s
sole discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.
PUMP, VACUUM MOTOR AND HEATER TWO-YEAR LIMITED WARRANTY: Mytee
warrants that pumps, vacuum and floor machine motors, and heaters will be free
from manufacturing defects, defects in workmanship, and defects in material for two
(2) years from the date of original purchase. This warranty does not apply and is void
if the pump, vacuum motor, or heater has worn brush motors, water damage, chemical build-up, chemical damage, or evidence of abuse, neglect or tampering. This
warranty covers the cost of replacement or repair only and does not cover shipping
or labor costs.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, modification, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor
or service center. Mytee may make changes in products it manufactures and markets
at any time; these changes are made without obligation to change, retrofit, or upgrade any product previously sold or manufactured.
Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the product intact,
unmodified, with all of its original parts.
If any provision or portion of this limited warranty policy is found to be unenforceable,
then the remaining provisions and portions shall remain valid and enforceable.
If any provision or portion of this limited warranty policy is found to be limited by law,
then that provision or portion shall be construed to make it effective within the
bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration
required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without
violating the law.
The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conflicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with
written authorization to ensure the Customers equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
1. When a repair falls within the Warranty time period for a piece of equipment, the
Distributor will fill out a RMA/Warranty claim form. This form will act as a repair order
to replace any defective parts.
2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.
3. When Warranty is approved, the Distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be
credited for any parts sent for this claim.
Mytee Products Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
PH 858.679.1191
F X 858.679.7814
© 2009 Mytee Products Inc.
Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising