Publicité
Publicité
SERVICE MANUAL
Synergy SA221S
WORLD HEADQUARTERS
CANADA
Yorkville Sound Limited
550 Granite Court
Pickering, Ontario
L1W 3Y8 CANADA
Voice: 905-837-8481
Fax: 905-837-8746
U.S.A.
Yorkville Sound Inc.
4625 Witmer Industrial Estate
Niagara Falls, New York
14305, USA
Voice: 716-297-2920
Fax: 716-297-3689
SA221S
SMT Disclaimer
Due to the complex nature of the use of SMT installed components in Yorkville equipment, we highly caution all service technicians in attempting to repair or replace SMT factory installed components.
Many of these components may be glued prior to initial soldering.
Replacing SMT components requires expensive specialized de-soldering equipment and training.
Yorkville Sound will repair and replace defective SMT components to ensure proper quality assurance and installation is maintained.
Manual-Service-SA221S-00-1v2 • Feb 17/2022
This lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Ce symbole d’éclair avec tête de flèche dans un triangle équilatéral est prévu pour alerter l’utilisateur de la présence d’un «voltage dangereux» non-isolé à proximité de l’enceinte du produit qui pourrait être d’ampleur suffisante pour présenter un risque de choque électrique.
The DO NOT STACK symbol is intended to alert the user that the product shall not be vertically stacked because of the nature of the product.
La symbole NE PAS EMPILER est pour alerter l'utilisateur que le produit ne doit pas être empilé verticalement en raison de la nature du produit.
IMPORTANT SAFETY INSTRUCTIONS
DO NOT
PUSH OR PULL
The exclamation point within an equilatereal triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est prévu pour alerter l’utilisateur de la présence d’instructions importantes dans la littérature accompagnant l’appareil en ce qui concerne l’opération et la maintenance de cet appareil.
SEPARATE
COLLECTION
WEEE
IEC 60417-5041
CAUTION: HOT SURFACE
ATTENTION: SURFACE CHAUDE
NOT TO BE SERVICED
BY USERS
CAUTION: OVERHEAD LOAD
ATTENTION: CHARGE AÉRIENNE
FOLLOW ALL INSTRUCTIONS
Instructions pertaining to a risk of fire, electric shock, or injury to a person
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. THIS DEVICE IS FOR INDOOR USE ONLY!
INSTALLED BATTERY PACKS SHALL NOT BE EXPOSED TO EXCESSIVE HEAT
SUCH AS SUNSHINE, FIRE OR THE LIKE.
SUIVEZ TOUTES LES INSTRUCTIONS
Instructions relatives au risque de feu, choc électrique, ou blessures aux personnes
AVIS: AFIN DE REDUIRE LES RISQUE DE CHOC ELECTRIQUE, N’ENLEVEZ PAS LE COUVERT (OU LE PANNEAU
ARRIERE) NE CONTIENT AUCUNE PIECE REPARABLE PAR L’UTILISATEUR. CONSULTEZ UN TECHNICIEN
QUALIFIE POUR L’ENTRETIENT CE PRODUIT EST POUR L’USAGE À L’INTÉREUR SEULEMENT. LES PACKS
BATTERIES INSTALLÉS NE DOIVENT PAS ÊTRE EXPOSÉS À UNE CHALEUR EXCESSIVE TELLE QUE LE
ENSOLEILLEMENT, LE FEU OU SIMILAIRES.
Read Instructions: The Owner’s Manual should be read and understood before operation of your unit. Please, save these instructions for future reference and heed all warnings.
Cleaning: Clean only with dry cloth.
Packaging: Keep the box and packaging materials, in case the unit needs to be returned for service.
Warning: To reduce the risk or fire or electric shock, do not expose this apparatus to rain or moisture. Do not use this apparatus near water!
Warning: When using electric products, basic precautions should always be followed, including the following:
Power Sources
Your unit should be connected to a power source only of the voltage specified in the owners manual or as marked on the unit. This unit has a polarized plug. Do not use with an extension cord or receptacle unless the plug can be fully inserted. Precautions should be taken so that the grounding scheme on the unit is not defeated. An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective earthing connection.
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
Hazards
Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious personal injury and serious damage to the product. Use only with cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. Only use attachments/accessories specified by the manufacturer.
Equipment that is suspended overhead must use a secondary safeguard to prevent personal injury in the event the primary mounting mechanism fails. Safety eyebolts attached to the equipment and galvanized steel wire can be used together to implement a failsafe mounting thus ensuring the safety of the equipment and anyone positioned below the equipment.
Improper installation can result in bodily injury or death. If you are not qualified to attempt the installation get help from a professional structural rigger.
Note: Prolonged use of headphones at a high volume may cause health damage to your ears.
The apparatus should not be exposed to dripping or splashing water; no objects filled with liquids should be placed on the apparatus.
Terminals marked with the “lightning bolt” are hazardous live; the external wiring connected to these terminals require installation by an instructed person or the use of ready made leads or cords.
Ensure that proper ventilation is provided around the appliance. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Power Cord
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. The AC supply cord should be routed so that it is unlikely that it will be damaged.
Protect the power cord from being walked on or pinched particularly at plugs. If the AC supply cord is damaged DO NOT OPERATE THE UNIT. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Service
The unit should be serviced only by qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, requires battery pack replacement or has been dropped.
Disconnect power before servicing!
Veuillez Lire le Manuel: Il contient des informations qui devraient êtres comprises avant l’opération de votre appareil. Conservez. Gardez S.V.P. ces instructions pour consultations ultérieures et observez tous les avertissements.
Nettoyage: Nettoyez seulement avec le tissu sec.
Emballage: Conservez la boite au cas ou l’appareil devait être retourner pour réparation.
Avertissement: Pour réduire le risque de feu ou la décharge électrique, n'exposez pas cet appareil à la pluie ou à l'humidité. N’utilisez pas cet appareil près de l’eau!
Attention: Lors de l’utilisation de produits électrique, assurez-vous d’adhérer à des précautions de bases incluant celle qui suivent:
Alimentation -
L’appareil ne doit être branché qu’à une source d’alimentation correspondant au voltage spécifié dans le manuel ou tel qu’indiqué sur l’appareil. Cet appareil est équipé d’une prise d’alimentation polarisée. Ne pas utiliser cet appareil avec un cordon de raccordement à moins qu’il soit possible d’insérer complètement les trois lames. Des précautions doivent êtres prises afin d’eviter que le système de mise à la terre de l’appareil ne soit désengagé. Un appareil construit selon les normes de CLASS I devrait être raccordé à une prise murale d’alimentation avec connexion intacte de mise à la masse. Lorsqu’une prise de branchement ou un coupleur d'appareils est utilisée comme dispositif de débranchement, ce dispositif de débranchement devra demeurer pleinement fonctionnel avec raccordement à la masse.
Risque -
Ne pas placer cet appareil sur un chariot, un support, un trépied ou une table instables. L’appareil pourrait tomber et blesser quelqu’un ou subir des dommages importants. Utiliser seulement un chariot, un support, un trépied ou une table recommandés par le fabricant ou vendus avec le produit. Suivre les instructions du fabricant pour installer l’appareil et utiliser les accessoires recommandés par le fabricant. Utilisez seulement les attachements/accessoires indiqués par le fabricant.
L'équipement suspendu au-dessus de la tête doit utiliser une protection secondaire pour éviter les blessures en cas de défaillance du mécanisme de montage principal. Les boulons à œil de sécurité fixés à l'équipement et le fil d'acier galvanisé peuvent être utilisés ensemble pour mettre en
œuvre un montage à sécurité intégrée, assurant ainsi la sécurité de l'équipement et de toute personne placée sous l'équipement.
Une installation incorrecte peut entraîner des blessures corporelles ou la mort. Si vous n'êtes pas qualifié pour tenter l'installation, demandez l'aide d'un gréeur structurel professionnel.
Remarque : L'utilisation prolongée d'écouteurs à un volume élevé peut nuire à la santé de vos oreilles.
Il convient de ne pas placer sur l’appareil de sources de flammes nues, telles que des bougies allumées.
L’appeil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures et qu’aucun objet rempli de liquide tel que des vases ne doit être placé sur l’appareil.
Assurez que lappareil est fourni de la propre ventilation. Ne procédez pas à l’installation près de source de chaleur tels que radiateurs, registre de chaleur, fours ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur.
Les dispositifs marqués d’une symbole “d’éclair” sont des parties dangereuses au toucher et que les câblages extérieurs connectés à ces dispositifs de connection extérieure doivent être effectivés par un opérateur formé ou en utilisant des cordons déjà préparés.
Cordon d’Alimentation -
Ne pas enlever le dispositif de sécurité sur la prise polarisée ou la prise avec tige de mise à la masse du cordon d’alimentation. Une prise polarisée dispose de deux lames dont une plus large que l’autre. Une prise avec tige de mise à la masse dispose de deux lames en plus d’une troisième tige qui connecte à la masse. La lame plus large ou la tige de mise à la masse est prévu pour votre sécurité. La prise murale est désuète si elle n’est pas conçue pour accepter ce type de prise avec dispositif de sécurité. Dans ce cas, contactez un électricien pour faire remplacer la prise murale. Évitez d’endommager le cordon d’alimentation. Protégez le cordon d’alimentation. Assurez-vous qu’on ne marche pas dessus et qu’on ne le pince pas en particulier aux prises. N’UTILISEZ PAS L’APPAREIL si le cordon d’alimentation est endommagé. Pour débrancher complètement cet appareil de l’alimentation CA principale, déconnectez le cordon d’alimentation de la prise d’alimentation murale. Le cordon d’alimentation du bloc d’alimentation de l’appareil doit demeurer pleinement fonctionnel.
Débranchez cet appareil durant les orages ou si inutilisé pendant de longues périodes.
Service -
L'appareil ne doit être entretenu que par un personnel de service qualifié. Une réparation est nécessaire lorsque l'appareil a été endommagé de quelque manière que ce soit, comme le cordon d'alimentation ou la fiche est endommagé, du liquide a été renversé ou des objets sont tombés dans l'appareil, l'appareil a été exposé à la pluie ou à l'humidité, ne fonctionne pas normalement , nécessite le remplacement de la batterie ou est tombé. Débranchez l'alimentation avant l'entretien!
IMPORTANT SAFETY INSTRUCTIONS
The Lightning Flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons
Le symbole représentant un éclair avec une flèche à l’intérieur d’un triangle équilatéral est utilisé pour prévenir l’utilisateur de la présence d’une tension électrique dangereuse non isolée à l’intérieur de l’appareil. Cette tension est d’un niveau suffisamment
élevé pour représenter un risque d’électrocution
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product
Le symbole représentant un point d’exclamation à l’intérieur d’un triangle équilatéral, signale à l’utilisateur la présence d’instructions importantes relatives au fonctionnement et à l’entretien de l’appareil dans cette notice d’installation
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prongs are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING:
• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
• To completely disconnect this apparatus from the ac mains, disconnect the power supply cord plug from the ac receptacle.
• The mains plug of the power supply cord or appliance coupler shall remain readily accessible.
1. Lisez ces instructions.
2. Conservez ces instructions.
3. Respecter tous les avertissements.
4. Suivez toutes les instructions.
5. N'utilisez pas l'appareil près de l'eau.
6. Nettoyer uniquement avec chiffon sec.
7. Ne bloquez pas les ouvertures de ventilation. Installer en suivant les instructions du fabricant.
8. Ne pas installer près des sources de chaleur telles que radiateurs, bouches de chaleur, four ou autres appareils (y compris les amplificateurs) produisant de la chaleur.
9. N'annulez pas l'objectif sécuritaire de la fiche polarisée ou de la tige de mise à la terre. Une fiche polarisée possède deux lames avec une plus large que l'autre. Une prise avec mise à la terre possède deux lames et une troisième tige. La lame large ou la troisième tige sont fournis pour votre sécurité.
Si la fiche n'entre pas dans votre prise, consultez un électricien pour remplacer la prise obsolète.
10. Protéger le cordon d'alimentation des piétinements ou pincements en particulier près des fiches, des prises de courant et au point de sortie de l'appareil.
11. Utilisez uniquement les accessoires spécifiés par le fabricant.
12. Utiliser uniquement avec un charriot, stand, trépied ou une table spécifiée par le fabricant, ou vendus avec l'appareil.
13. Débranchez l'appareil durant un orage ou lorsqu'il reste inutilisé pendant de longues périodes de temps.
14. Confiez toute réparation à un technicien qualifié. Une réparation est nécessaire lorsque l'appareil a été endommagé de quelque façon que ce soit; comme lorsque le cordon d'alimentation ou la fiche est endommagé, lorsque du liquide a été renversé ou des objets sont tombés à l'intérieur, lorsque l'appareil a été exposé à la pluie ou l'humidité, ne fonctionne pas normalement, ou est tombé.
AVERTISSEMENT:
• Pour réduire les risques d'incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à l'humidité et ne placez pas d’objets contenant des liquides, tels que des vases, sur l’appareil.
• Pour isoler totalement cet appareil de l'alimentation secteur, débranchez totalement son cordon d'alimentation du réceptacle CA.
• La prise du cordon d’alimentation ou du prolongateur, si vous en utilisez un comme dispositif de débranchement, doit rester facilement accessible
CAUTION
TO PREVENT ELECTRIC SHOCK HAZARD,
DO NOT CONNECT TO MAINS POWER SUPPLY
WHILE GRILLE IS REMOVED.
AVIS
POUR PRÉVENIR LES RISQUES D'ÉLECTROCUTION,
NE PAS RACCORDER A L’ALIMENTATION ÉLECTRIQUE ALORS
QUE LA GRILLE EST RETIRÉE.
DOC-Safety-5v0+UL60065-00-1v9 • February 2, 2022
15 AMP
12A = MAX Output
8A = 80% Output
6A = 60% Output
LINE
CURRENT
LIMIT
AMPS
12
8
6
100Hz
Lowpass
-6
-2
SUB
LEVEL
0
1
-12
-24
Off dB
8
Power Activity
6
2
4
Input
Clip
50Hz
Lowpass
(for use with
SA315S)
Limit
VC Therm
X-MAX
OUTPUT
INPUT
HP
OUTPUT
50Hz
HP OUTPUT TO
SA315S ONLY
SA221S A-Z1789 / 1v2
SERIAL NUMBER
DESIGNED & MANUFACTURED BY
YORKVILLE SOUND • TORONTO, CANADA
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK,
GROUNDING OF THE CENTRE PIN OF THIS PLUG MUST BE MAINTAINED!
ATTENTION - POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, CONSERVER
LA MISE À LA TERRE ASSURÉE PAR LA TIGE CENTRALE DE CETTE FICHE!
DISCONNECT POWER BEFORE SERVICING!
DEBRANCHER L’APPAREIL AVANT
D’ENLEVER LES COUVERCLES!
NO USER SERVICEABLE PARTS INSIDE.
NE CONTIENT AUCUNE PIECE
REPARABLE PAR L’UTILISATEUR.
POWER
On
Circuit
Breaker
CAUTION: THIS EQUIPMENT REQUIRES A 15A OR 20A LINE CORD
ATTENTION: CET ÉQUIPMENT NÉCESSITE
UN CORDON DE LIGNE 15A OU 20A
120V 60Hz
11A STANDALONE
1A MAX ON
FIRST OUTLET
12A MAX WITH
AND 15A LINE CORD
Off
Specifications
Active or Passive Active
Program Power (watts) 6000 watts program 17000 watts peak
130.6 dB Cont., 142.6 dB Peak Measured Max SPL (C-Weighted, Max Hold)
Frequency Response (Hz +/- 3dB)
Crossover Frequency (Hz)
Cabinet Configuration
Driver Configuration
LF Driver(s)
LF Program Power (watts)
LF Impedance (ohms)
LF Protection
LF Power Amplifier (watts)
28Hz-100Hz
50 or 100 Hz lowpass
Bass Reflex
2x21-inch LF woofer
21-inch Neo with 4.5-inch Tetra Coil
6000 watts Program, 17000 watts Peak
LF impedance 2 amplifiers, 4 ohms per amplifier
Excursion, Voice Coil Thermal (RMS)
LF Amplifier Type
Cooling Scheme
Power Cable
Power Switch
Power Consumption (typ/max)
Inputs
Input Sensitivity (Vrms Sine)
Level Controls
EQ Controls
Limiter
LED Indicators
Enclosure Materials
Casters
Stand Adapter
UHMW Skid Glides
Stacking Feature
Covering / Finish
Dimensions (DWH inches)
Dimensions (DWH cm)
Weight (lbs/kg)
6000 watts program (17000 watts peak)
Class D
Convection
Removable Locking Powercon True Input and Loop Thru
Yes
1440 VA / 1920 VA
1 XLR with 2x XLR Parallel out, Impedance 35k ohms
Line in 1.4 at center, 0.56 at max
Volume, -∞,0dB,8dB (Min, Top, Max)
Thermal Limiter Advance for power consumption management
Excursion, Thermal (RMS), Clipping
Power, Excursion Limit, Thermal (RMS) Limit, Input Clip,
Multiply 15mm Birch Plywood
4 x Locking Swivel Casters On Rear Of Cabinet
2 (1 Top, 1 Side)
2 Rear
Rubber Feet and Cups (Side and Bottom)
Paint
32.750 (37.750 including casters) x 29.750 x 47.5
83.2 (95.8 including casters) x 75.5 x 120.6
370/168
*Specifications subject to change without notice
Spécifications
Actif ou passif Actif
Puissance Nominale (watts) 6000 watts de programme 17000 watts de crête
130,6 dB Cont., 142,6 dB Crête SPL maximum mesuré (pondéré C, maintien maximum)
Réponse en fréquence (Hz +/- 3dB)
Fréquence de coupure (Hz)
Configuration de l'enceinte
Configuration des haut-parleurs
Driver(s) BF
Puissance du programme BF (watts)
Impédance BF (ohms)
Protection BF
Amplificateur de puissance BF (watts)
28Hz-100Hz
Passe-bas 50 ou 100 Hz
Bass Reflex
Woofer BF 2x21 pouces
Neo de 21 pouces avec bobine Tetra de 4,5 pouces
6000 watts en programme, 17000 watts en crête
Impédance BF 2 amplificateurs, 4 ohms par amplificateur
Excursion, bobine de voix thermique (RMS)
Type d'amplificateur BF
Système de refroidissement
Cordon d'alimentation
Commutateur d'alimentation
Consommation électrique (typ/max)
Entrées
Sensibilité d'entrée (Vrms sinus)
Commandes de niveau
Commandes d'égalisation
Limiteur
Indicateurs DEL
Matériaux du boîtier
Roues
Adaptateur de support
Glissières de protection UHMW
Caractéristiques d'empilage
Revêtement / Finition
Dimensions (PLH pouces)
Dimensions (PLH cm)
Poids (livres/kg)
6000 watts programme (17000 watts crête)
Classe D
Convection
Verrouillage amovible Powercon Entrée True et sortie Loop
Oui
1440 VA / 1920 VA
1 XLR avec 2x XLR sortie parallèle, Impédance 35k ohms
Entrée ligne 1,4 au centre, 0,56 au maximum
Volume, -∞,0dB,8dB (Min, Top, Max)
Limiteur thermique Advance pour la gestion de la
Excursion, thermique (RMS), écrêtage
Puissance, Limite d'excursion, Limite thermique (RMS), Clip
Contreplaqué de bouleau de 15mm
4 roulettes pivotantes verrouillables à l'arrière de l'armoire
2 (1 dessus, 1 latérale)
2 Arrière
Pieds et coupelles en caoutchouc (côté et dessous)
Peinture
32,750 (37,750 avec les roulettes) x 29,750 x 47,5
83,2 (95,8 avec les roulettes) x 75,5 x 120,6
370/168
*Spécifications sujettes à modification sans préavis
B l o c k D i a g r a m S A 2 2 1 S
D E S I G N E D & M A N U FA C T U R E D B Y Y O R K V I L L E S O U N D
Pwr Act.
Input
Clip
Limit
X-Max
VC
Therm
1
3
2
Input
2
3
1
Output
2
3
1
XLR
AC Line
Sense
ADC
DSP
DAC
Microcontroller
AC Line
Current Sense
50Hz
LP
Sub
Level
1
3
2
Line
Current
Limit
HP
Output
+
-
AMP
+
-
AMP block-diagram-SYNERGY-SA221S-00-1v1
5972
5225
7813
5979
7917
5979
5979
7969
7601
7875
5986
5986
7769
7871
8176
5979
5979
5979
5979
7603
7693
7871
7693
5972
5979
5979
5979
5979
5979
5979
5979
5979
7742
7742
7742
7832
8109
8109
7700
7750
7832
7738
8814
6300
6300
8814
8814
7832
7742
7875
7735
7735
7735
7875
7875
7735
5979
5934
5934
5979
7697
8096
7603
7601
7875
7697
5979
7880
7735
5217
7735
5934
5934
YS #
M1806-59
M1806BLANK
5982
7809
5949
5949
7734
C228
C229
C230
C231
C232
C233
C234
C235
C220
C221
C222
C223
C224
C225
C226
C227
C210
C211
C212
C213
C216
C217
C218
C219
C202
C203
C204
C205
C206
C207
C208
C209
D8
D9
D10
D11
D12
D13
D14
D15
D16
D4
D5
D6
D7
C242
D1
D2
D3
C22
C24
C25
C26
C28
C30
C31
C200
C14
C15
C16
C17
C18
C19
C20
C21
C6
C7
C8
C9
C10
C11
C12
C13
C2
C3
C4
C5
REF
AI-SUB
BLANK
C1
Description
SA315S AMP/SUPPLY PCB AI
3_OZ 2SD 83.4 SQIN 01PER SA315
150P 1000V 5%CAP 1206 SMT C0G
_10U 16V 20%CAP 5X5.4 SMT NP
__3U3 140AC10%CAP BLK RAD POLYP FLM
__3U3 140AC10%CAP BLK RAD POLYP FLM
__1U0 50V 10%CAP 1206 SMT CER
_22U 16V 5%CAP 5X5.5 SMT ELC
100N 50V 5%CAP 0805 SMT X7R
_47U 35V 20%CAP 6.3MM SMT ELE
__4U7 50V 10%CAP 1210 SMT CER
_22N 560V 10%CAP BLK RAD POLY FLM
__4U7 50V 10%CAP 1210 SMT CER
2700U 250V 20%CAP BLK 40X60MM 4PS
2700U 250V 20%CAP BLK 40X60MM 4PS
2700U 250V 20%CAP BLK 40X60MM 4PS
2700U 250V 20%CAP BLK 40X60MM 4PS
100N 50V 5%CAP 0805 SMT X7R
_22U 16V 5%CAP 5X5.5 SMT ELC
470N 100V 10%CAP 1206 SMT X7R
680P 50V 5%CAP 0805 SMT C0G
220N 50V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
__4U7 50V 10%CAP 1210 SMT CER
__4U7 50V 10%CAP 1210 SMT CER
__4U7 50V 10%CAP 1210 SMT CER
100N 100V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
__4U7 50V 10%CAP 1210 SMT CER
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
680P 50V 5%CAP 0805 SMT C0G
__1N 50V 5%CAP 0805 SMT NPO
470P 50V 5%CAP 0603 SMT NPO
__1N 50V 5%CAP 0805 SMT NPO
680N 400V 5%CAP BLK RAD POLY FLM
220N 50V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
_10U 600VDC 5%CAP BLK MPOLYP FLM
_10U 600VDC 5%CAP BLK MPOLYP FLM
__1U 50V 20%CAP 4.3X3.9 SMT ELC
470P 50V 5%CAP 0603 SMT NPO
_47N 100V 10%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
680N 400V 5%CAP BLK RAD POLY FLM
470P 1600V 20%CAP POLYPROP BULK
_47P 50V 5%CAP 0805 SMT NPO
100N 50V 5%CAP 0805 SMT X7R
_33U 25V 20%CAP 6.3X5.5 SMT EL
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
_10U 16V 20%CAP 0805 SMT X5R
_10U 16V 10%CAP 1206 SMT X7R
ES1J 600V 1A0 DO214AC SMT SMA
MURA260T3 600V 2A DIO 403D SMT
MURA260T3 600V 2A DIO 403D SMT
ES1J 600V 1A0 DO214AC SMT SMA
ES1J 600V 1A0 DO214AC SMT SMA
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
B0540 SOD123 SMT SCHTKY
B0540 SOD123 SMT SCHTKY
B0540 SOD123 SMT SCHTKY
B0540 SOD123 SMT SCHTKY
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
BAV21WS 200V 0A2 SOD323 SMT
BAV21WS 200V 0A2 SOD323 SMT
5237B 8V2 0W2 SOT-23 SMT ZEN
CDSF4148 75V 0A15 1005 SMT
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
7628
7680
8189
5084
5084
5068
5068
5068
2321
8165
2321
5068
7852
5096
8137
7852
6847
8165
7986
6847
8165
6977
6977
7846
7974
8101
7967
6699
7915
7720
5190
6730
7622
7860
7625
7645
7645
7645
7651
5082
7645
5068
5000
7651
7651
7651
8274
7863
8274
8902
3846
4249
8701
8701
8832
8485
8101
4233
4233
Z1740
8902
8485
8742
8835
8800
7617
7750
3414
3414
2498
2498
5136
5136
YS #
7700
7619
7750
6300
7619
8814
8814
R6
R7
R8
R9
R10
R11
R12
R13
R2
R3
R4
R5
Q203
Q204
Q205
R1
Q5
Q7
Q8
Q9
Q10
Q11
Q12
Q13
Q1
Q2
Q3
Q4
L2
L3
L7
L200
R22
R24
R25
R26
R27
R28
R29
R30
R31
R14
R15
R16
R17
R18
R19
R20
R21
HW10
HW11
HW12
HW13
HW14
HW15
HW17
L1
HS1
HS2
HS3
HW2
HW4
HW6
HW7
HW8
F3
F4
F5
F6
D213
D214
F1
F2
REF
D17
D18
D19
D20
D28
D204
D205
M1806-03 Parts Reference List 5/19/2021
Description
5237B 8V2 0W2 SOT-23 SMT ZEN
BZX84C43 43V0 0W3 5% SMT ZEN
CDSF4148 75V 0A15 1005 SMT
MURA260T3 600V 2A DIO 403D SMT
BZX84C43 43V0 0W3 5% SMT ZEN
ES1J 600V 1A0 DO214AC SMT SMA
ES1J 600V 1A0 DO214AC SMT SMA
BZX84C15LT1 15V0 0W225 ZEN SOT23
CDSF4148 75V 0A15 1005 SMT
INTERNATIONAL PC MOUNT FUSEHOLDER
INTERNATIONAL PC MOUNT FUSEHOLDER
30.0 AMP SLO-BLO .25X1.25 FUSE
30.0 AMP SLO-BLO .25X1.25 FUSE
FUSE 1A25 500VDC SMT F4319
FUSE 1A25 500VDC SMT F4319
22X17X2MM ALN CERAMIC TO247 INSUL
22X17X2MM ALN CERAMIC TO247 INSUL
M1806 HEAT SPREADER
4-40X3/4 PAN PHILIPS MS TBZ
#6 SPLIT WASHER ZINC
4-40X3/8 PAN PH TAPTITE BO&W
6-32X1/2 PAN QUAD MS TIN PLATE
6-32 KEPS NUT ZINC
4-40X3/4 PAN PHILIPS MS TBZ
TO220 THERMO PAD LARGE HOLE 56359B
1POS XSISTOR SPRING
4-40 KEPS NUT ZINC
4-40 KEPS NUT ZINC
6-32X1/4 PAN PH TAPTITE JS500
#6 SPLIT WASHER ZINC
120.0UH COIL A34 1R6 SMT
1000UH 10% COIL 12MM SMT
120.0UH COIL A34 1R6 SMT
_15.0UH COIL 0805 SMT
_453UH CHOKE 91T14.5AWG/79912CORE
T810-600G-TR 8A TRIAC D2PAK SMT
TL431A 3 TERM ADJ VREG SMT SOT-23
MBS4992 TO92 8V5 DIAC T&R
IRF830 TO220 NCH MFET TN
MMBTA42 NPN SOT-23 SMT
MMBTA92 PNP SOT-23 SMT
2N7002 NCH FET SOT-23 SMT T&R
MMBTA42 NPN SOT-23 SMT
MMBTA92 PNP SOT-23 SMT
FDT3612 NCH MFET SOT-223 SMT
FDT3612 NCH MFET SOT-223 SMT
MC7815BDTG POS REG SMT DPAK3
IKW75N65EH5 T0247 NPN 75A IGB3
MMBTA92 PNP SOT-23 SMT
IKW75N65EH5 T0247 NPN 75A IGB3
W125 187K 0.1% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W125 28K7 1% 0805 SMT RES
W125 1K62 1% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W100 15K0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 140K 1% 0805 SMT RES
W250 1M0 1% 1206 SMT RES
W250 1M0 1% 1206 SMT RES
W250 1M0 1% 1206 SMT RES
W125 6K20 1% 0805 SMT RES
W125 33K 5% 0805 SMT RES
W125 6K20 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 4K7 5% 0805 SMT RES
W100 10K0 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W250 1M0 1% 1206 SMT RES
W125 1K27 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
R232
R233
R234
R236
R237
R238
R240
R242
R222
R223
R224
R225
R226
R227
R229
R231
R203
R204
R210
R214
R215
R218
R219
R221
R63
R70
R72
R73
R74
R200
R201
R202
R259
R260
R261
R262
R268
SNL1
T4
T5
U1
R243
R244
R247
R249
R251
R255
R256
R258
R55
R56
R57
R58
R59
R60
R61
R62
R47
R48
R49
R50
R51
R52
R53
R54
R39
R40
R41
R42
R43
R44
R45
R46
REF
R32
R33
R34
R35
R36
R37
R38
7621
7680
7630
7680
7802
5084
7856
5079
7625
7680
7854
7930
7628
7622
7852
7621
7625
7761
7634
7860
7824
8321
7673
7856
7654
5082
7621
5095
5095
7821
7761
7821
7630
4931
7686
7622
8189
8370
8188
8188
8158
5079
5070
7860
7852
7930
7703
7703
7634
5088
5088
5088
5088
4703
4703
7654
7654
5096
7645
7688
7622
7626
7864
8008
7864
7622
7821
7621
7645
7645
7645
7645
7645
YS #
7645
7645
7645
7863
7645
7645
7676
Description
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 33K 5% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 2K0 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 10R0 1% 0805 SMT RES
W100 1K0 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 28K7 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 4M7 5% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 100K0 1% 0805 SMT RES
W125 100K 5% 0805 SMT RES
W250 10K 5% ANTISURGE 0805 SMT RES
W125 100K 5% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
2W00 2R 5% T&R RES
2W00 2R 5% T&R RES
W250 619K 1% 1206 SMT RES
W250 619K 1% 1206 SMT RES
W250 619K 1% 1206 SMT RES
W125 1K27 1% 0805 SMT RES
W100 1K0 1% 0805 SMT RES
W250 33R 5% 1206 SMT RES
W250 33R 5% 1206 SMT RES
W125 10R0 1% 0805 SMT RES
W100 12K1 1% 0603 SMT RES
W125 10R0 1% 0805 SMT RES
W100 10K0 1% 0805 SMT RES
W100 12K1 1% 0603 SMT RES
W100 20K5 1% 0805 SMT RES
W125 4K7 5% 0805 SMT RES
W125 47K5 1% 0805 SMT RES
W125 8K66 1% 0805 SMT RES
W100 475R 1% 0805 SMT RES
W125 470R 5% 0805 SMT RES
W100 10K0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W125 47R 5% 0805 SMT RES
W250 22R 5% 1206 SMT RES
W100 15K0 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W100 1K0 1% 0805 SMT RES
W100 1K0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W100 182K 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
1W00 1R0 5% 2512 SMT RES
W125 33R 5% 0805 SMT RES
W125 470R 5% 0805 SMT RES
2W00 0R02 1% OARS SMT RES
2W00 0R02 1% OARS SMT RES
2W00 0R05 1% OARS SMT RES
W125 4K7 5% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W250 22R 5% 1206 SMT RES
W125 82K5 1% 0805 SMT RES
W125 82K5 1% 0805 SMT RES
W100 20K5 1% 0805 SMT RES
W100 182K 1% 0805 SMT RES
470K 5% THERMISTOR NTC 0805 SMT
W100 274K 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
1 MIL POLYIMIDE LABEL, 1" X .380"
XF3955 GATE DRIVE XFMR SMT
XF3955 GATE DRIVE XFMR SMT
LNK306G OFFLINE SWITCH SMT SMD8B
6686
7817
7817
8163
3538
3538
4146
4163
YS #
7661
7949
7949
7987
6668
7851
7851
3538
2328
7832
W1
W2
W3
W4
U203
U204
U205
U206
REF
U2
U3
U4
U8
U200
U201
U202
W5
W201
ZD200
Description
LM393D DUAL COMPARATOR SMT SO-8
ZXGD3002E6 GATE DRVR 9A SMT SOT326
ZXGD3002E6 GATE DRVR 9A SMT SOT326
UCC25600 RES MODE CTRL SMT SO8
LTV-8141S ACINPUT OPTOCOUPLER SMT
LM311 COMPARATOR IC SMT SO-8
LM311 COMPARATOR IC SMT SO-8
IRS21844SPBF IC HILO FET DRVR SO14
33078 DUAL OPAMP SMT SO-8
33078 DUAL OPAMP SMT SO-8
TL331 COMPARATOR IC SMT SOT235
24 PIN BREAKAWAY LOCK .156
24 PIN BREAKAWAY LOCK .156
3 PIN POWER PIN HEADER MALE POLZED
5 PIN POWER PIN HEADER MALE POLZED
24 PIN BREAKAWAY LOCK .156
8 CIR XH-HEADER 0.098IN
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
REF YS # Description
REF YS #
AI-ASS M1813-59
C1
C2
8178
8178
4010
4140
R4
W1
W2
J1
J2
J3
L1
PCB1
R1
R2
R3
Description
SA153 INPUT
470P 250V 5%CAP 0603 SMT NP0
470P 250V 5%CAP 0603 SMT NP0
XLR FEML PCB MT VERT 24MM AA-SERIES
XLR MALE PCB MT VERT 24MM A-SERIES
XLR MALE PCB MT VERT 24MM A-SERIES
_15.0UH COIL 0805 SMT
4140
7967
M1813BLANK 2_OZ 2SD 81.2 SQIN 12PER SA153
6543
7624
7624
4967
3966
2357
48R 265V RESETTABLE THERMISTOR PTC
W100 100R 1% 0805 SMT RES
W100 100R 1% 0805 SMT RES
W125 39K2 1% 0805 SMT RES
GRN 16AWG PREFUSED WIRE
4 CIR XH-HEADER RA 0.098IN
M1813 01 Parts Reference List 9/29/2020
REF YS # Description REF YS # Description
REF YS #
AI-ASS M1831-59
J1
PCB1
W1
Description
SA115S/SA221S INPUT
4140 XLR MALE PCB MT VERT 24MM A-SERIES
M1831BLANK 2_OZ 2SD 46.16 SQIN 21PER SA221S
2369 3 CIR PH-HEADER 2MM
M1831-01 Parts Reference List 5/19/2021
REF YS # Description REF YS # Description
W5
W6
W7
W8
W9
SNL1
W1
W3
W4
R5
R6
R12
R13
R14
R15
R16
R17
R1
R2
R3
R4
L1
PCB
Q3
Q4
D2
D3
D4
D11
D12
D13
K1
K2
4851
4842
4894
4894
4841
4838
8370
4263
6854
5101
2504
2504
2504
2504
4621
4621
4147
4146
4163
4147
4151
4146
4151
C3
C4
C5
C6
C32
C33
C34
D1
REF YS #
AI-ASS M1832-59
C1
C2
5242
5266
5865
5865
5914
6451
5629
5260
5959
6775
6775
6438
6438
6438
6438
6438
3696
3019
Description
SA221S/SA115S AC INPUT
100N 250V 20%CAP BLK 'X2' 15MM AC
680N 250V 20%CAP BLK 'X2' 27MM AC
100N 250V 10%CAP BLK RAD POLY FLM
100N 250V 10%CAP BLK RAD POLY FLM
100U 63V 20%CAP BLK 10X13MM EL
__4N7 250V 20%CAP BLK 'Y' 10MM AC
_10U 160V 20%CAP BLK 10X13MM EL
_22U 50V 20%CAP T&R RAD .2EL
_10U 450V 20%CAP BLK EL
BRIDGE 25A 600V WIRE LEAD SIP
BRIDGE 25A 600V WIRE LEAD SIP
1N4007 1000V 1A0 DIODE T&R
1N4007 1000V 1A0 DIODE T&R
1N4007 1000V 1A0 DIODE T&R
1N4007 1000V 1A0 DIODE T&R
1N4007 1000V 1A0 DIODE T&R
RELAY 1C 02AMP DC24 006MA PC-S
RELAY 1C 30AMP DC110 08MA PC-C
3817 _1.5MH COIL INPUT COM MODE
M1832BLANK 3_OZ 2SD 41 SQIN 1PER SA221S AC IN
2N6517 350V TO92 NPN TRAN TA
BC550C TO92 NPN TRAN T&R TB
__2R 25% 35A INRSH CURR LIM 36MM
__2R 25% 35A INRSH CURR LIM 36MM
__2R 25% 35A INRSH CURR LIM 36MM
__2R 25% 35A INRSH CURR LIM 36MM
W500 470R 5% T&R RES
W500 470R 5% T&R RES
W250 120K 5% T&R RES
W250 330K 5% T&R RES
W250 130K 5% T&R RES
W250 130K 5% T&R RES
W250 220K 5% T&R RES
W250 100K 5% T&R RES
1 MIL POLYIMIDE LABEL, 1" X .380"
2 CIR HDR VERT HI CURR 0.224IN SPC
6 PIN POWER PIN HEADER MALE POLZED
3 PIN POWER PIN HEADER MALE POLZED
5 PIN POWER PIN HEADER MALE POLZED
6 PIN POWER PIN HEADER MALE POLZED
4 PIN POWER PIN HEADER MALE POLZED
3 PIN POWER PIN HEADER MALE POLZED
4 PIN POWER PIN HEADER MALE POLZED
M1832-02 Parts Reference List 8/9/2021
REF YS # Description REF YS # Description
5979
7603
7693
7871
7693
5972
7601
7875
5979
5979
5979
5979
5979
5979
5979
5979
7738
7738
7875
7693
7693
5979
5979
5979
7875
7735
6011
6011
6011
6011
6011
7875
7813
5979
7917
5979
5979
7969
7738
8814
6300
5986
5986
7769
7871
8176
5979
5972
5225
7875
6011
7735
7735
7735
6011
6011
6011
5923
5923
5979
7697
8096
7603
7601
7875
7697
5979
7880
7735
5217
7735
5923
5923
YS #
M1833-59
M1833BLANK
5982
7809
5949
5949
7734
C212
C213
C216
C217
C218
C219
C220
C221
C204
C205
C206
C207
C208
C209
C210
C211
C38
C39
C40
C41
C42
C200
C202
C203
C30
C31
C32
C33
C34
C35
C36
C37
C230
C231
C232
C233
C234
C235
C242
D1
D2
C222
C223
C224
C225
C226
C227
C228
C229
C22
C23
C24
C25
C26
C27
C28
C29
C14
C15
C16
C17
C18
C19
C20
C21
C6
C7
C8
C9
C10
C11
C12
C13
C2
C3
C4
C5
REF
AI-SUB
BLANK
C1
Description
SA115S/SA221S AMP/SUPPLY PCB AI
3_OZ 2SD 83.6 SQIN 01PER SA115S/221
150P 1000V 5%CAP 1206 SMT C0G
_10U 16V 20%CAP 5X5.4 SMT NP
__3U3 140AC10%CAP BLK RAD POLYP FLM
__3U3 140AC10%CAP BLK RAD POLYP FLM
__1U0 50V 10%CAP 1206 SMT CER
_22U 16V 5%CAP 5X5.5 SMT ELC
100N 50V 5%CAP 0805 SMT X7R
_47U 35V 20%CAP 6.3MM SMT ELE
__4U7 50V 10%CAP 1210 SMT CER
_22N 560V 10%CAP BLK RAD POLY FLM
__4U7 50V 10%CAP 1210 SMT CER
3300U 250V 10%CAP BLK 40X80MM 4PS
3300U 250V 10%CAP BLK 40X80MM 4PS
3300U 250V 10%CAP BLK 40X80MM 4PS
3300U 250V 10%CAP BLK 40X80MM 4PS
100N 50V 5%CAP 0805 SMT X7R
_22U 16V 5%CAP 5X5.5 SMT ELC
470N 100V 10%CAP 1206 SMT X7R
680P 50V 5%CAP 0805 SMT C0G
220N 50V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
_33N 630V 5%CAP 1210 SMT COG
__4U7 50V 10%CAP 1210 SMT CER
__4U7 50V 10%CAP 1210 SMT CER
__4U7 50V 10%CAP 1210 SMT CER
_33N 630V 5%CAP 1210 SMT COG
_33N 630V 5%CAP 1210 SMT COG
_33N 630V 5%CAP 1210 SMT COG
100N 100V 10%CAP 1206 SMT X7R
__4U7 50V 10%CAP 1210 SMT CER
_33N 630V 5%CAP 1210 SMT COG
_33N 630V 5%CAP 1210 SMT COG
_33N 630V 5%CAP 1210 SMT COG
_33N 630V 5%CAP 1210 SMT COG
_33N 630V 5%CAP 1210 SMT COG
100N 100V 10%CAP 1206 SMT X7R
_10U 16V 10%CAP 1206 SMT X7R
_10U 16V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
__1N 50V 5%CAP 0805 SMT NPO
__1N 50V 5%CAP 0805 SMT NPO
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
680P 50V 5%CAP 0805 SMT C0G
__1N 50V 5%CAP 0805 SMT NPO
470P 50V 5%CAP 0603 SMT NPO
__1N 50V 5%CAP 0805 SMT NPO
680N 400V 5%CAP BLK RAD POLY FLM
220N 50V 10%CAP 1206 SMT X7R
100N 100V 10%CAP 1206 SMT X7R
_10U 600VDC 5%CAP BLK MPOLYP FLM
_10U 600VDC 5%CAP BLK MPOLYP FLM
__1U 50V 20%CAP 4.3X3.9 SMT ELC
470P 50V 5%CAP 0603 SMT NPO
_47N 100V 10%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
680N 400V 5%CAP BLK RAD POLY FLM
470P 1600V 20%CAP POLYPROP BULK
_47P 50V 5%CAP 0805 SMT NPO
100N 50V 5%CAP 0805 SMT X7R
_33U 25V 20%CAP 6.3X5.5 SMT EL
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
_10U 16V 20%CAP 0805 SMT X5R
_10U 16V 10%CAP 1206 SMT X7R
ES1J 600V 1A0 DO214AC SMT SMA
MURA260T3 600V 2A DIO 403D SMT
6847
6847
8165
7986
6847
8165
6977
6977
8101
2919
7967
6699
7915
7720
5190
6730
4124
4249
8701
8701
8832
8485
8101
7974
8800
8902
8485
8742
8835
8835
8800
8902
5096
8137
7852
7628
7680
8189
5084
5084
5068
7846
6847
6847
2321
8165
2321
5068
7852
8814
7617
7750
5136
5136
4233
4233
Z1740
7619
7750
6300
7832
7832
7832
7619
8814
7742
7832
8109
8109
7700
7750
7700
7700
YS #
6300
8814
8814
7832
7742
7742
7742
Q5
Q6
Q7
Q8
Q9
Q10
Q11
Q12
Q1
Q2
Q3
Q4
L3
L4
L7
L200
HW11
HW12
HW13
HW14
HW15
HW17
L1
L2
HW1
HW2
HW4
HW6
HW7
HW8
HW9
HW10
R3
R4
R5
R6
R7
R8
R9
R10
R11
Q13
Q14
Q15
Q203
Q204
Q205
R1
R2
D205
D213
D214
F5
F6
HS1
HS2
HS3
D18
D19
D20
D23
D24
D25
D28
D204
D10
D11
D12
D13
D14
D15
D16
D17
D6
D7
D8
D9
REF
D3
D4
D5
M1833-02 Parts Reference List 5/19/2021
Description
MURA260T3 600V 2A DIO 403D SMT
ES1J 600V 1A0 DO214AC SMT SMA
ES1J 600V 1A0 DO214AC SMT SMA
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
B0540 SOD123 SMT SCHTKY
B0540 SOD123 SMT SCHTKY
B0540 SOD123 SMT SCHTKY
B0540 SOD123 SMT SCHTKY
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
BAV21WS 200V 0A2 SOD323 SMT
BAV21WS 200V 0A2 SOD323 SMT
5237B 8V2 0W2 SOT-23 SMT ZEN
CDSF4148 75V 0A15 1005 SMT
5237B 8V2 0W2 SOT-23 SMT ZEN
5237B 8V2 0W2 SOT-23 SMT ZEN
BZX84C43 43V0 0W3 5% SMT ZEN
CDSF4148 75V 0A15 1005 SMT
MURA260T3 600V 2A DIO 403D SMT
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
BZX84C43 43V0 0W3 5% SMT ZEN
ES1J 600V 1A0 DO214AC SMT SMA
ES1J 600V 1A0 DO214AC SMT SMA
BZX84C15LT1 15V0 0W225 ZEN SOT23
CDSF4148 75V 0A15 1005 SMT
FUSE 1A25 500VDC SMT F4319
FUSE 1A25 500VDC SMT F4319
22X17X2MM ALN CERAMIC TO247 INSUL
22X17X2MM ALN CERAMIC TO247 INSUL
M1806 HEAT SPREADER
6-32 KEPS NUT ZINC
4-40X3/4 PAN PHILIPS MS TBZ
#6 SPLIT WASHER ZINC
4-40X3/8 PAN PH TAPTITE BO&W
6-32X1/2 PAN QUAD MS TIN PLATE
6-32X1/2 PAN QUAD MS TIN PLATE
6-32 KEPS NUT ZINC
4-40X3/4 PAN PHILIPS MS TBZ
SILPAD 1500ST 1.100 X0.820 BERQUIST
1POS XSISTOR SPRING
4-40 KEPS NUT ZINC
4-40 KEPS NUT ZINC
6-32X1/4 PAN PH TAPTITE JS500
#6 SPLIT WASHER ZINC
120.0UH COIL A34 1R6 SMT
1000UH 10% COIL 12MM SMT
120.0UH COIL A34 1R6 SMT
__0.18UH 20% COIL 11MM SMT
_15.0UH COIL 0805 SMT
_453UH CHOKE 91T14.5AWG/79912CORE
T810-600G-TR 8A TRIAC D2PAK SMT
TL431A 3 TERM ADJ VREG SMT SOT-23
MBS4992 TO92 8V5 DIAC T&R
IRF830 TO220 NCH MFET TN
MMBTA42 NPN SOT-23 SMT
MMBTA42 NPN SOT-23 SMT
MMBTA92 PNP SOT-23 SMT
2N7002 NCH FET SOT-23 SMT T&R
MMBTA42 NPN SOT-23 SMT
MMBTA92 PNP SOT-23 SMT
FDT3612 NCH MFET SOT-223 SMT
FDT3612 NCH MFET SOT-223 SMT
MC7815BDTG POS REG SMT DPAK3
MMBTA42 NPN SOT-23 SMT
MMBTA42 NPN SOT-23 SMT
IKW75N65EH5 T0247 NPN 75A IGB3
MMBTA92 PNP SOT-23 SMT
IKW75N65EH5 T0247 NPN 75A IGB3
W125 187K 0.1% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W125 28K7 1% 0805 SMT RES
W125 1K62 1% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W100 15K0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
R71
R72
R73
R74
R75
R76
R77
R78
R61
R62
R63
R64
R65
R66
R67
R70
R53
R54
R55
R56
R57
R58
R59
R60
R44
R45
R46
R47
R48
R49
R50
R51
R210
R214
R215
R218
R219
R221
R222
R223
R224
R79
R80
R81
R200
R201
R202
R203
R204
R36
R37
R38
R39
R40
R41
R42
R43
R28
R29
R30
R31
R32
R33
R34
R35
R19
R20
R21
R22
R24
R25
R26
R27
REF
R12
R13
R14
R15
R16
R17
R18
7645
7621
5095
5095
7864
7645
7645
7645
7654
7654
7654
7864
7864
7864
7645
5082
8008
7622
5088
5088
5088
5088
4703
4703
7645
7645
7645
5096
7645
7688
7622
7626
7634
7860
7824
8321
7673
7856
7625
7680
7854
7864
7864
7622
7821
7761
7821
7625
7761
7645
7645
7676
7622
7821
7621
7645
7645
7645
7651
5082
7645
7645
7645
7645
7863
8274
7863
8274
7622
7860
7625
7645
7645
YS #
5068
5068
5068
5000
7651
7651
7651
Description
W125 187K 0.1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 140K 1% 0805 SMT RES
W250 1M0 1% 1206 SMT RES
W250 1M0 1% 1206 SMT RES
W250 1M0 1% 1206 SMT RES
W125 6K20 1% 0805 SMT RES
W125 33K 5% 0805 SMT RES
W125 6K20 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 4K7 5% 0805 SMT RES
W100 10K0 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W250 1M0 1% 1206 SMT RES
W125 1K27 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 33K 5% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 2K0 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 10R0 1% 0805 SMT RES
W100 1K0 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 28K7 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 4M7 5% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 100K0 1% 0805 SMT RES
W250 10K 5% ANTISURGE 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
W125 49K9 1% 0805 SMT RES
2W00 2R 5% T&R RES
2W00 2R 5% T&R RES
W250 619K 1% 1206 SMT RES
W250 619K 1% 1206 SMT RES
W250 619K 1% 1206 SMT RES
W125 100K 5% 0805 SMT RES
W125 100K 5% 0805 SMT RES
W125 100K 5% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 1K27 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 1K0 1% 0805 SMT RES
W250 33R 5% 1206 SMT RES
W250 33R 5% 1206 SMT RES
W125 100K 5% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W100 475K 1% 0805 SMT RES
W125 100K 5% 0805 SMT RES
W125 100K 5% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 10R0 1% 0805 SMT RES
W100 12K1 1% 0603 SMT RES
W125 10R0 1% 0805 SMT RES
W100 10K0 1% 0805 SMT RES
W100 12K1 1% 0603 SMT RES
W100 20K5 1% 0805 SMT RES
W125 4K7 5% 0805 SMT RES
W125 47K5 1% 0805 SMT RES
W125 8K66 1% 0805 SMT RES
W100 475R 1% 0805 SMT RES
W125 470R 5% 0805 SMT RES
W100 10K0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W125 47R 5% 0805 SMT RES
7686
7622
8189
8370
8188
8188
8158
7661
7860
7852
7930
7703
7703
7634
7630
4931
7630
7680
7802
5084
7856
5079
5079
5070
YS #
7930
7628
7622
7852
7621
7621
7680
7817
7817
8163
3538
3538
4146
4163
3538
2328
7832
7949
7949
7836
7987
6668
7851
7851
6686
T4
T5
U1
U2
R261
R262
R268
SNL1
R247
R249
R251
R255
R256
R258
R259
R260
R234
R236
R237
R238
R240
R242
R243
R244
REF
R225
R226
R227
R229
R231
R232
R233
W2
W3
W4
W5
U204
U205
U206
W1
W201
ZD200
U3
U4
U5
U8
U200
U201
U202
U203
Description
W250 22R 5% 1206 SMT RES
W100 15K0 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W100 1K0 1% 0805 SMT RES
W100 1K0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W100 182K 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
1W00 1R0 5% 2512 SMT RES
W125 33R 5% 0805 SMT RES
W125 470R 5% 0805 SMT RES
2W00 0R02 1% OARS SMT RES
2W00 0R02 1% OARS SMT RES
2W00 0R05 1% OARS SMT RES
W125 4K7 5% 0805 SMT RES
W250 10R 5% 1206 SMT RES
W250 22R 5% 1206 SMT RES
W125 82K5 1% 0805 SMT RES
W125 82K5 1% 0805 SMT RES
W100 20K5 1% 0805 SMT RES
W100 182K 1% 0805 SMT RES
470K 5% THERMISTOR NTC 0805 SMT
W100 274K 1% 0805 SMT RES
W100 1M0 1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
1 MIL POLYIMIDE LABEL, 1" X .380"
XF3955 GATE DRIVE XFMR SMT
XF3955 GATE DRIVE XFMR SMT
LNK306G OFFLINE SWITCH SMT SMD8B
LM393D DUAL COMPARATOR SMT SO-8
ZXGD3002E6 GATE DRVR 9A SMT SOT326
ZXGD3002E6 GATE DRVR 9A SMT SOT326
TLC555 TIMER SMT SO8 IC
UCC25600 RES MODE CTRL SMT SO8
LTV-8141S ACINPUT OPTOCOUPLER SMT
LM311 COMPARATOR IC SMT SO-8
LM311 COMPARATOR IC SMT SO-8
IRS21844SPBF IC HILO FET DRVR SO14
33078 DUAL OPAMP SMT SO-8
33078 DUAL OPAMP SMT SO-8
TL331 COMPARATOR IC SMT SOT235
24 PIN BREAKAWAY LOCK .156
24 PIN BREAKAWAY LOCK .156
3 PIN POWER PIN HEADER MALE POLZED
5 PIN POWER PIN HEADER MALE POLZED
24 PIN BREAKAWAY LOCK .156
8 CIR XH-HEADER 0.098IN
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
REF YS # Description
C10
F1
F2
F3
F4
F5
F6
PCB
C6
C7
C8
C9
REF
C1
C2
C5
SNL1
W1
W2
W4
W5
YS #
5911
5911
5911
5911
5911
5911
5911
Description
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
5911
2499
2499
3477
2700U 250V 20%CAP BLK 40X63MM 4PS
1.25 AMP SLO-BLO 500V AXIAL FUSE
1.25 AMP SLO-BLO 500V AXIAL FUSE
5AG FUSE CLIP CARTRIDGE 30A PCB
3477
3477
5AG FUSE CLIP CARTRIDGE 30A PCB
5AG FUSE CLIP CARTRIDGE 30A PCB
3477 5AG FUSE CLIP CARTRIDGE 30A PCB
M1834BLANK 3_OZ 2SD 58.7 SQIN 01PER SA221S CAP
8370
4194
4146
4147
4151
1 MIL POLYIMIDE LABEL, 1" X .380"
2X2 3 MM MICRO MATE-N-LOK VRT
3 PIN POWER PIN HEADER MALE POLZED
6 PIN POWER PIN HEADER MALE POLZED
4 PIN POWER PIN HEADER MALE POLZED
M1834-01 Parts Reference List 5/19/2021
REF YS # Description REF YS # Description
REF
PCB
R74
SNL1
T1
W2
W10
W11
W12
W13
1233
4056
4151
4151
4151
4263
YS # Description
M1837BLANK 3_OZ 2SD 60.9SQIN 6PER SYNERGY CURR
4683
8370
1W00 1K8 5% T&R RES
1 MIL POLYIMIDE LABEL, 1" X .380"
CURRENT XMFR SML PC MNT EI-25
2 CIR XH-HEADER 0.098IN
4 PIN POWER PIN HEADER MALE POLZED
4 PIN POWER PIN HEADER MALE POLZED
4 PIN POWER PIN HEADER MALE POLZED
2 CIR HDR VERT HI CURR 0.224IN SPC
M1837-01 Parts Reference List 5/19/2021
REF YS # Description REF YS # Description
W2
W4
W5
C8
C9
C10
F1
F2
PCB
SNL1
W1
C4
C5
C6
C7
REF
C1
C2
C3
YS #
5911
5911
5911
5911
5911
5911
5911
Description
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
5911
5911
5911
2499
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
2700U 250V 20%CAP BLK 40X63MM 4PS
1.25 AMP SLO-BLO 500V AXIAL FUSE
2499 1.25 AMP SLO-BLO 500V AXIAL FUSE
M1840BLANK 2_OZ 2SD 58.7 SQIN 01PER SA315/221S
8370
4194
4146
4147
4151
1 MIL POLYIMIDE LABEL, 1" X .380"
2X2 3 MM MICRO MATE-N-LOK VRT
3 PIN POWER PIN HEADER MALE POLZED
6 PIN POWER PIN HEADER MALE POLZED
4 PIN POWER PIN HEADER MALE POLZED
M1840-01 Parts Reference List 5/19/2021
REF YS # Description REF YS # Description
D40
K1
L2
L3
L6
L7
L10
L11
L12
LD1
LD2
LD3
LD4
D4
D5
D6
D7
D10
D11
D12
D39
C51
C52
C55
C134
C135
D1
D2
D3
C43
C44
C45
C46
C47
C48
C49
C50
C35
C36
C37
C38
C39
C40
C41
C42
C27
C28
C29
C30
C31
C32
C33
C34
C19
C20
C21
C22
C23
C24
C25
C26
7750
7750
7750
7750
7750
7750
7750
3700
7811
5979
5979
6657
7750
7750
6657
7832
8253
7878
5979
7738
7738
7738
7927
7927
7871
5979
5979
7927
5212
5212
8253
8253
7967
8152
7941
7941
7967
7967
7967
7031
7032
7033
7032
5979
5979
5979
7871
7871
5979
7878
7878
5979
7878
5979
7878
5979
7878
7878
5979
5979
5979
5979
5212
7738
7969
5979
5979
5979
5669
5945
5945
5233
5233
5212
5979
C11
C12
C13
C14
C15
C16
C17
C18
C3
C4
C5
C6
C7
C8
C9
C10
REF YS # Description
AI-ASS M1950-59 SA221S INPUT DSP BOARD 1OZ
C1
C2
5979
7871
7878
5979
100N 50V 5%CAP 0805 SMT X7R
470P 50V 5%CAP 0603 SMT NPO
__1U 25V 20%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
470U 6V3 20%CAP RAD EL T&R
_10U 63V 20%CAP T&R RAD .2EL
_10U 63V 20%CAP T&R RAD .2EL
330N 63V 5%CAP T&R RAD .2FLM
330N 63V 5%CAP T&R RAD .2FLM
100N 100V 5%CAP T&R RAD .2FLM
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 100V 5%CAP T&R RAD .2FLM
_10U 16V 10%CAP 1206 SMT X7R
_10U 16V 20%CAP 0805 SMT X5R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
__1U 25V 20%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
__1U 25V 20%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
__1U 25V 20%CAP 1206 SMT X7R
__1U 25V 20%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
470P 50V 5%CAP 0603 SMT NPO
470P 50V 5%CAP 0603 SMT NPO
100N 50V 5%CAP 0805 SMT X7R
__1U 25V 20%CAP 1206 SMT X7R
__1U 25V 20%CAP 1206 SMT X7R
470P 50V 5%CAP 0603 SMT NPO
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
100P 50V 10%CAP 0805 SMT NPO
100N 100V 5%CAP T&R RAD .2FLM
100N 100V 5%CAP T&R RAD .2FLM
20P 100V 5%CAP 0805 SMT NPO
20P 100V 5%CAP 0805 SMT NPO
20P 100V 5%CAP 0805 SMT NPO
__1U 25V 20%CAP 1206 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
_10U 16V 10%CAP 1206 SMT X7R
_10U 16V 10%CAP 1206 SMT X7R
_10U 16V 10%CAP 1206 SMT X7R
100P 50V 10%CAP 0805 SMT NPO
100P 50V 10%CAP 0805 SMT NPO
100U 25V 20%CAP 8X5.4 SMT ELE
100N 50V 5%CAP 0805 SMT X7R
100N 50V 5%CAP 0805 SMT X7R
B160-E3 60V 1A0 SCH DO214AC SMT
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
B160-E3 60V 1A0 SCH DO214AC SMT
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
CDSF4148 75V 0A15 1005 SMT
RELAY 2C 01AMP DC24 015MA PC-S
_15.0UH COIL 0805 SMT
220UH COIL 10X10MM SMT
__8.2UH COIL 1210 SMT
__8.2UH COIL 1210 SMT
_15.0UH COIL 0805 SMT
_15.0UH COIL 0805 SMT
_15.0UH COIL 0805 SMT
GRN LED 2V8 20MA 1206 SMT
YEL LED 1V7 20MA 1206 SMT
RED LED 1V5 20MA 1206 SMT
YEL LED 1V7 20MA 1206 SMT
M1950-03 Parts Reference List 5/19/2021
R53
R54
R55
R56
R57
R58
R59
R62
R44
R45
R46
R47
R48
R49
R51
R52
R35
R36
R37
R38
R39
R40
R41
R42
R26
R27
R28
R29
R30
R31
R32
R33
R73
R75
R76
R107
R165
R176
R177
R178
R181
R65
R66
R67
R68
R69
R70
R71
R72
R18
R19
R20
R21
R22
R23
R24
R25
R10
R11
R12
R13
R14
R15
R16
R17
R6
R7
R8
R9
R2
R3
R4
R5
Q1
Q2
Q3
R1
REF
LD6
P4
PCB1
8189
7928
7928
7740
8135
8135
5084
8027
7676
8189
7857
7708
7676
5068
5068
8189
7676
7928
7680
5066
5067
7637
7864
7898
5067
7860
5084
5084
8189
7951
7951
7854
7857
7671
7671
7680
7624
7670
7745
8027
7821
7928
7820
7670
7860
7632
7821
7928
7624
7624
7781
7854
7624
8135
8135
7928
7928
7858
7820
7928
7708
7951
7849
7676
7676
7638
7675
8027
5066
7928
7820
7951
7820
YS #
7031
Description
GRN LED 2V8 20MA 1206 SMT
2339 _10K B LIN 12MM DUAL 21DET P34
M1950BLANK 1_OZ 2SD 60.67SQIN 3PER SA221S INP
7837
7837
6847
7951
MMBT5401 PNP SOT-23 SMT
MMBT5401 PNP SOT-23 SMT
MMBTA42 NPN SOT-23 SMT
W125 750R 1% 0805 SMT RES
W100 3K74 1% 0805 SMT RES
W125 1K21 1% 0805 SMT RES
W125 37K4 1% 0805 SMT RES
W125 22K1 1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W100 499R 1% 0805 SMT RES
W125 750R 1% 0805 SMT RES
W100 499R 1% 0805 SMT RES
W125 1K5 5% 0805 SMT RES
W100 499R 1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W100 200R 1% 0805 SMT RES
W125 750R 1% 0805 SMT RES
W250 0R27 5% 1206 SMT RES
W100 2K0 1% 0805 SMT RES
W100 2K0 1% 0805 SMT RES
W100 100R 1% 0805 SMT RES
W063 49R9 1% 0603 SMT RES
W125 47R 5% 0805 SMT RES
W100 100R 1% 0805 SMT RES
W125 47K 5% 0805 SMT RES
W125 47K 5% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W100 499R 1% 0805 SMT RES
W125 47R5 1% 0805 SMT RES
W125 4K7 5% 0805 SMT RES
W100 2K32 1% 0805 SMT RES
W125 10R0 1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W100 100R 1% 0805 SMT RES
W125 249R0 1% 0805 SMT RES
W125 249R0 1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W100 100R 1% 0805 SMT RES
W125 47R5 1% 0805 SMT RES
W125 0R 5% 0805 SMT RES
W125 37K4 1% 0805 SMT RES
W125 10R0 1% 0805 SMT RES
W125 4K7 5% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
W125 750R 1% 0805 SMT RES
W125 750R 1% 0805 SMT RES
W125 47R 5% 0805 SMT RES
W125 560R 5% 0805 SMT RES
W100 2K0 1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
W125 560R 5% 0805 SMT RES
W100 200R 1% 0805 SMT RES
W100 2K0 1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 187K 0.1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
W125 4K02 0.1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W125 698R 1% 0805 SMT RES
W125 47K 5% 0805 SMT RES
W125 47K 5% 0805 SMT RES
W125 33R 5% 0805 SMT RES
W125 37K4 1% 0805 SMT RES
W100 2K0 1% 0805 SMT RES
W125 10K00 0.1% 0805 SMT RES
W100 6K98 1% 0805 SMT RES
W125 22K1 1% 0805 SMT RES
W125 31K6 0.1% 0805 SMT RES
W125 3K32 1% 0805 SMT RES
W125 100K 5% 0805 SMT RES
W125 1K02 0.1% 0805 SMT RES
W125 31K6 0.1% 0805 SMT RES
W3
W4
W6
W8
ZD1
ZD2
U8
U9
W1
W2
U4
U5
U6
U7
TP10
TP12
TP13
TP14
TP15
U1
U2
U3
REF
S1
S4
SNL2
TP1
TP7
TP8
TP9
4183
2328
2369
4056
7832
7832
6667
7012
7012
7669
7669
7669
2357
2328
8002
8002
8002
8002
8002
7817
7719
6670
YS #
3522
4189
8372
8002
8002
8002
8002
Description
DPDT MINI PC VERT SNP ALT
DP4T NONSHORTING VERT ROT SWT
1 MIL POLYIMIDE LABEL,.375" X .375"
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
TEST POINT MINIATURE SMT
33078 DUAL OPAMP SMT SO-8
MC33063ADR BUCK/BOOST INV IC SO8
AK4558 32BIT CODEC SMT QFN28
MK10DN512VLK10 100MHZ MCU IC LQFP80
LP2950-33 LDRP TO92 FIXED 3V3 REG
LP2950-33 LDRP TO92 FIXED 3V3 REG
TL072 DUAL OPAMP SMT SO-8
TL072 DUAL OPAMP SMT SO-8
TL072 DUAL OPAMP SMT SO-8
4 CIR XH-HEADER RA 0.098IN
8 CIR XH-HEADER 0.098IN
10 CIR DUAL ROW HDR 0.05 SPC SMT
8 CIR XH-HEADER 0.098IN
3 CIR PH-HEADER 2MM
2 CIR XH-HEADER 0.098IN
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
MM3Z18VT1G 18V0 0W2 5% SMT ZEN
A
B
E
F
I
J
K
C
D
G
H
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
SUBWOOFER AMP
PILink301 PILink302
+15VS
100N
PIC20201
50V
PIC20202
0805
100N
PIC21201
50V
0805
PIC21202 LVGND
+15V_MOD
100N
PIC20301
50V
PIC20302
0805
100N
PIC20401
50V
PIC20402
0805
100N
PIC20501
50V
PIC20502
0805
100N
PIC20901
50V
PIC20902
0805
100N
PIC21001
50V
PIC21002
0805
100N
PIC21101
50V
PIC21102
0805
100N
PIC23302
50V
PIC23301
0805
100N
PIC23401
50V
PIC23402
0805
+15VS
+15V_MOD
WOOFGND
PIN121101 PIR20002 PIR20001
+/-15V_MOD
0805
10R0
100N
PIC20601
PIC20602
50V
COC206
0805
100N
PIC20701
PIC20702
50V
COC207
LVGND
0805
PIN121201
CON1212
-15V_MOD
0805
10R0
PIR20202
-15VS
+15VS
100N
PIC20001
PIC20002
50V
COC200
0805
WOOFGND 100N
PIC20801
PIC20802
50V
COC208
0805 LVGND
PILink201
-15VS
PILink402
PILink202
PILink401
PILink501 PILink502
PSGND WOOFGND
1
PIEC201
CON_HOLE_189
-15VS
-15V_MOD
LVGND
0805
10K0
PIR20302
PSGND
FROM INPUT PCB
8
W201:2 8
W201:3 8
W201:4
8
W201:5 8
W201:6 8
W201:7 8
W201:8
8
PIN120101
PIN120801
PIN120201
PIN120301
LVGND
+Fuse
PIR5501 W125 PIR5502
49K9
0805
PIR5601 W125 PIR5602
49K9
0805
+15V_MOD
PIR21502
PIR21501
47K5
0805
OC
PIR5701 W125 PIR5702
PID21302
PID21301
D213
49K9
COD213
SOT-23
15V0
W125 PIR5802
49K9
0805
PIN120701
LVGND
POLVGND2
N1207
WOOFGND
PIR21902
PIR21901
475R0
0805
WOOFGND
PIR20401 W100 PIR20402
0603
12K1
+15V_MOD
+
PIU20108 PIU20105
-
PIU20104 PIU20106
W100 PIR20102
12K1
0603
-15V_MOD
PIU20107
PIU20101
PIN120601
PIN120401
+15VS
PIN120501
CON1205
-15VS
470P
0603
50V
PIR23301 PIR701
PIR23302
0805
6K98
0805
PIR702
6K98
PIC22501
50V
470P
0603
PIC22502
PIR22301 1/8W PIR22302
0805
6K98
+15V_MOD
50V
PIC22001
220N
1206 PIU20508
COU205:3
DUAL OPAMP 2
-
PIR23602
COR236
6K98
PIR23601
0805
3
+
PIU20504
-15V_MOD
1
PIR23101
W100
PIR23102
7817
0805
1K0
MC33078D
PIC22002
PIR23201
W100
PIR23202
3
+
0805
1K0
100V
47N
PIC22602
PIC22601
2
-
1206
+15V_MOD
PIR21402
PIR21401
4K7
0805
SILENT ON/OFF
SILENT
LM311
7851
SO8
PIR21801 W125 PIR21802
0805
8K66
PIC21302
680P
PIC21301
50V
0805
+15V_MOD
PIR22201
D1005
PIR26801 W125 PIR26802
CDSF4148
4K02
0805
6
PIU20406 -
PIU20408
U204:2
DUAL OPAMP
PIR22202
10K0
0805
PIR22102
5
+
PIU20404
7817
MC33078D
PIR22101
470R
0805
-15V_MOD
U204:1
DUAL OPAMP
MC33078D
7817
10U
PIC24201
16V PIC24202
1206
W125 PIR802
0805
4K02
WOOFGND
0805
1N
COC218
PIC21801
50V
W125 PIR22402
0805
47R
PIR22701 W100 PIR22702
0805 1M0
6
-
MC33078D
U205:2
DUAL OPAMP
7817
7
5
+
PIR24002
PIR24001
470R
0805
WOOFGND
PIR25902
PIR25901
182K
0805
PIR25802
PIR25801
20K5
0805
PIR26102
PIR26101
274K
0805
PIR26002 COR260
PIC23501
10U
0805
PIR26001
470K
PIC23502
10V
0805
+Hi
-
+
PIU20605
+15V_MOD
+
-
PIU20208 PIU20205
PIU20204 PIU20206
-15V_MOD
W100 PIR26202
1M0
0805
PIU20602
8163
PIC21602
TL331
COU206
SOT23-5
COC216
0805
50V
1N
PIC21601
PIU20207
PIU20201
LM311
7851
SO8
PIQ20401
WOOFGND
+15V_MOD
PIR21002
COR210
PIC23001
0805
PIR21001
20K5
PIC23002 47P
50V
0805
PIR22602
PIR6302
619K
PIR6301
1206
W250 PIR23002
1206
DNS
1
PIU301
2
IN1
VCC
SINK
1206
10R
PIR22902
+Hi
PIR22601
15K0
0805
PIR6102
619K
PIR6101
1206
PIR22501
W250
PIR22502
1206
22R
PIQ20301 IN2 SOURCE
SOT23-6
GND
3
PIU303
ZXGD3002E6
7949
PIR6202
SOD123
DNS
PIQ20403
619K
PIR6201
1206
PIR23402 PIR23401
182K
0805
PIQ20402
MMBTA92
8165
SOT-23
+15V_LS
PID20401
PID20402
ES1J
DO-214AC
PIR24702
PIR23702 1W00 PIR23701
1R0
2512
PIR24701
4K7
0805
PIR2402
PIR2401
4K7
0805
PIC23201
33U
PIC23202
25V
6x6mm
PIC23101
100N
PIC23102
50V
0805
ES1J
DO-214AC
PIR902
PIR901
33R
0805
COU203
IRS21844S
VCC HO
VB 13
VS
PIU203013
11
IN
SD
DT
COM
LO
VSS
PIR1002 PIR1001
33R
0805
6686
SO14
PIR2502
10K0
PIR2501
0805
PIC22101
100N
COC221
100V PIC22102
1206
PIC22401
1U PIC22402 50V
4X4mm
PIZD20002
PIZD20001
18V0
SOD-323
PIR2301 W250 PIR2302
1206
DNS
+15V_LS
1
PIU401
2
IN1
VCC
SINK
PIR24901 W250 PIR24902
1206
10R
COD21
SOD123
DNS
2321 T0247
IKW75N65EH5
COQ205 PIQ20502
PIQ20501
+15V_LS
PIQ20503
IN2
SOT23-6
SOURCE W250 PIR25102
1206
GND
3
PIU403
ZXGD3002E6
22R 100N
100V
PIC2202
1206
7949
PIC2201
PIQ20303
PIQ20302
IKW75N65EH5
PIC2301
T0247
2321
PIC22902
PIC22901
PIR5902
.
COR59
PIR5901
2R
PIR6002
.
PIR6001
2R
PIC2302
1210
1600V
470p
PIC2701
PIC2702
1210
W125 PIR25502
0805
82K5
W125 PIR25602
0805
82K5
-Hi
CHSGND
PIC22201 PIC22301
PIC21901
PIC21902
680N
400V
PIC22202
600V
10U
RAD POLY
PIC22302
600V
10U
RAD POLY
PIC301 PIC401
PIC302
140V
3U3
RAD POLY
PIC402
PIL20002 PIL20001
453UH
6699
PIR24202 PIR24302
PIC22802
PIC22801
400V
COC228
680N
W125 PIR102
PSGND
COR11
187K
0805 PIR1202
187K
0805
PIR1102
PIR24201
0R02
OARS
187K
PIL402
2919
0.18UH
PIR1201
0805
PIR24301
0R02
OARS
RAD POLY
140V
3U3
PIR24402
PIR24401
0R05
OARS
PIL401
11mm
W125 PIR23802
0805
33R
COC227
100N
PIC22701
50V
0805
PIC22702
2
PIU20002
PIR1302
187K
PIR1301
0805
T810-600G-TR
7915
PIQ102
D2PAK
PIQ302 TO92 PIQ303 W250
PIQ103
10R
1206
MBS4992
5190 {Voltage}
PIQ101
1206
PIC102
PIC101
187K
0805
PIR1402
10U 16V
5X5.5mm
PSGND
CON_HOLE_189
PIC3501
PIC3502
1210
PIC3601
PIC3602
1210
PIC2801
PIC2802
1210
RED
CON_HOLE_140
PSGND
CON_HOLE_140
1 2 3 4 5 6 7 8
4
3
2
1
RED
BLK
BLK
9 10
WOOFER
YS #8357
11 12
CON_HOLE_140
CHSGND
13 14
6668
4PIN SMT
LTV-8141S
4 W5:4
4 W5:3
4
1
4
W5:2
4
3
4
W1:4
W1:3
4 W1:2
4
4 W2:4
4
2
4
1
PIW201 4
W2:3
W2:2
Section:
Product(s):
Woofer Amp
SA315S/SA221S
PCB# M1806
Date Modified:
Rev#
2020-07-30
V04 BOM Rev#
Filename:
01 Sheet
Amp.SCHDOC
15 16
1 Of
17
3
G
D
E
F
H
I
J
K
C
A
B
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
K
B
C
D
E
F
G
H
I
J
PIL701 PIL702
7967
+15V_LS
MURA260
403D
+Fuse
MURA260T3
PIC1001
PIC1002
PID201
PID202
PIR501
403D
PIR502
10R
1206
PIU104
5
D
LNK306G
0805
100N
50V
PIU103
S
S
S
S
1
2
7
PIU107
8
8158
SMD8B
PP RAD
560VDC
22N
PIR401
PIR301
W125
PIR302
28K7
0805
1K62
PIR402
0805
PID302
PID301
MURA260T3
403D
PIF602
PIF601
1A25
5136
PIC901
PIC902
1210
ES1J
DO-214AC
PIL202
7974
1000UH
CAPACITOR BANK #2
W3:2
W3:3
3
3
3
CON_HOLE_189
PSGND
OC
PSGND
PIN301
PIL201
PIC1101
PIC1102
1210
151mA
+31V
31.3V
PID2802
PID2801
SOT-23
43V0
PIC802
PIC801
6x6mm
47U
35V
MC7815BDTG
PIQ1301 IN OUT
GND
PIQ1302
7846
DPAK3
PIQ1303
8
PIU208
V+
7661
V-
4
PIU204
U2:3
LM393D
SO8
+15V_LS
PIR7002
PIC3101
PIC3102 COC31
1210
4U7
50V
PIR7001
1K27
0805
PIR602
PIR601
15K0
0805
PIC502
PIC501
1206
RT
DT
SS
PIU807
PIU806
UCC25600
7987
SO8
GD2
OC
PIR7202
1K0
PIR7201
0805
50V
1210
XF3955
W250 PIQ1101
G
33R
1206
W250 PIQ1201
G
33R
1206
D
PIQ1102
S
PIQ1103
FDT3612
6977
SOT233
D
PIQ1202
S
PIQ1203
FDT3612
6977
SOT233
PIC2602
PIC2402
PIC2601
PIC2401
-Fuse
PIC 6
PIC 7
PIC 6
PIC 5
PIR1502
PIR1501
140K0
0805
PIR2102
PIR2101
6K20
0805
PIR2002
33K
PIR2001
0805
PIR1902
PIR1901
PIR3001
6K20
0805
PIR3002
1K27
0805
2V5
PIQ202
PIQ203
PIQ201
7720
TL431A
PIC1601
PIC1602
COC16 C16
100N
50V
SOT23
0805
-
+Fuse W250 PIR2902
1M0
1206
W250 PIR1602 W250 PIR1702 W250 PIR1802
1M0
1206
1M0
1206
1M0
1206
W250 PIR5302
10K
0805
PSGND
CAPACITOR BANK
5
W4:2 5
W4:3 5
W4:4 5
W4:5 5
PIC2102
PIC2101
1206
PIR2201 W100 PIR2202
1M0
0805
7
SO8
PIU207
7661
LM393D
U2:2
+ +
SO8
1
7661
LM393D
COU2:1
+Fuse
UNDER VOLTAGE SHUT DOWN MAY NOT NEED
PIR3402
PIR3401
475K
0805
PIR4302
PIR4301
475K
0805
PIR3501
33K
0805 PIQ702 TURN ON VOLTAGE
Place above 3414 holder in schematic
FROM POWER SUPPLY
(OPEN COLLECTOR)
SOD-323
200V
SOD-323
200V
+Hi
PIQ701 SOT-23 MMBTA92
PIQ703
8165
PID1402
PID1401
SOT-23
8V2
+Fuse
PIC2902
PIC2901
1210
PIC3202
PIC3201
1210
-Fuse
T30.0 AMP
2498
PIF101 PIF102
30A 3AB
COF1
+Hi
PIN401
PIC1201
PIC1202
250V
3300U
40X80MM
PIC1302
PIC1301
40X80MM
3300U
250V
CON_HOLE_189
PIC3302
PIC3301
1210
PID502
PID501
ES1J
DO-214AC
PIN701
PIC3402
PIC3401
PSGND
1210
Place above 3414 holder in schematic
PIC1402
PIC1401
250V
3300U
40X80MM
PIC1502
PIC1501
40X80MM
3300U
250V
PID402
PID401
ES1J
DO-214AC
T30.0 AMP
2498
SILENT
PSGND
PIR5402
100K
0805
PIF201 PIF202
30A 3AB
COF2
-Hi
PIN801
PIR5202 W125 PIR5201
100K
0805
PIR4702
2N7002
28K7
PIR4701
0805
W125
PIQ803
D
G
PIQ801
SOT-23
7986 PIQ802 S
SOT-23
PIQ1003
SOT-23
43V0
PID1702
PID1701
SOT-23
8V2
PIQ1002
TO POWER AMP PCB
D1005
CDSF4148
PIC2001
1206
PIC2002
220N
50V
W125 PIR4902
4M7
0805
PIQ1001
8165
MMBTA92 PID1901
PID1902
D1005
CDSF4148
PSGND
PIR4602
475K
PIR4601
0805
PIR4802
475K
PIR4801
0805
PID1602
PID1601
SOD-323
18V0
PIR5102
SOT-23
PIQ903
PIQ902
PIR5101
100K0
0805
PSGND
PIR4402 PIR4401
475K
0805
PIQ901
MMBTA42
6847
4PIN SMT
6668
PIR4502 PIR4501
475K
0805
PIR5002
1M0
PIR5001
0805
LTV-8141S
1210
1210
SOD123
B0540
SOD123
B0540
+15V
100N
100V
PIC3701
PIC3702
1206
-Hi
22U
PIC1702
16V
PIC1701
PIL102
120uH
8101
COC17
5X5.5mm
PIL101
+15V_MOD
XF3955
5
PIT405
SOD123
B0540
100N
PIC3002
100V
PIC3001
1206
SOD123
B0540 -15V
+Hi
PIF502
5136
1A25
PIF501
PID601
PID602
SOD-323
18V0
PIR2702
+Hi_Dis
475K
PIR2701
0805
PIR2802
DISCHARGE RAILS
475K
PIR2801
0805
PIR3202
475K
PIR3201
0805
PIR4202
475K
PIR4201
0805
22U
PIC601
C6
PSGND
COC6
COL3
16V
PIC602
PIL302
120uH
8101
470N
1206
100V PIR3702
475K
PIR3701
0805
D
PIQ402
IRF830
N
TO220
6730
PIR2602
PIR2601
475K
0805
PIR3102
PIR3101
475K
0805
PIR3302
PIR3301
475K
0805
PIR3602
PIR3601
COR36
475K
0805
PIL301
S
PIQ403
PIR4102
PIR4101
1K0
0805
SOD-323
18V0
PIC1902
PIC1901
0805
-15V_MOD
HEATSINK
BLEEDER CIRCUIT
PIQ503
SOT-23 PIQ502
PIQ501
6847
MMBTA42
PIR3801 W100 PIR3802
2K0
0805
PIR3902
1M0
PIR3901
0805
W100
PIR4001
PIR4002
10R0
0805
Section:
Product(s):
Power Supply
SA315S/SA221S
PCB# M1806
Date Modified:
Rev#
2020-07-30
V04 BOM Rev#
Filename:
01 Sheet
Supply15V.SCHDOC
2
15 16
Of
17
3
K
1 2 3 4 5 6 7 8 9 10 11 12 13 14
B
C
D
E
F
G
H
I
J
J
A
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
B
C
D
E
F
H
I
G
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
3
4
7
8
9
10
11
12
13
1
2
#
.
.
.
.
.
.
.
.
.
.
.
.
9
10
11
12
13
6
7
8
3
4
5
1
2
.
DATE
# DATE
5
6
7
8
9
3
4
1
2
10
11
12
13
.
.
.
.
.
08-NOV-2018
06-FEB-2019
27-FEB-2019
14-MAY-2019
.
.
25-FEB-2020
VER#
V01
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
V02
V03
.
V04
.
.
.
.
.
.
.
9380
9384
PC#
#9351
#9358
DESCRIPTION OF CHANGE
RELEASED FOR PRODUCTION
Changed Values, Added D20 and Connected Pin 4 of W201 to Pin 1 of W3
Change Capacitor C229 from #5221 to new #5225 470P 1.6kV
RELEASED FOR PRODUCTION
Replace #8761 heatsink mtg screw with #8835
Add Fuse YS#5136 in series with +Hi net at D6
Add Fuse YS#5136 in series with net -Fuse
Add 9 Capacitors YS#6011 and Inductor YS#2919 for EMI Emissions
Moved traces for extra grounding and Compliance issues.
.
.
.
Added extra chassis mechanical mounting to PCB and Heat Sink.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
DESCRIPTION OF CHANGE
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
REF
.
.
.
.
.
.
.
.
.
.
.
.
.
FUNCTION
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
POT#
.
.
.
.
.
.
.
.
.
.
.
.
.
STYLE
.
.
.
.
.
.
.
.
.
.
.
.
.
KNOB#
PINOUT DIAGRAMS
CASES AND PINS
1
2
3
4
5
6
7
IRS21844S
IN
SD
VSS
DT
COM
LO
VCC
NC
VB
HO
VS
NC
NC
NC
14
13
12
11
10
9
8
#6686
NJM7815 NJM7915
I G O
#6856
G I O
#6857
IRGP50B60PDPBF
IRGP35B60PDPBF
TO-247AC
G D S
#2496 #2307
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
14
Section:
Product(s):
Design Information And History
SA315S/SA221S
PCB#: M1806
Modified: 2020-07-30
Rev#:
File:
V04 EML Rev#:
History.SchDoc
01 Sheet 3 Of
Tmp Rev: V028
15 16 17
3
K
J
I
CLINCH
ORIGIN
3 OZ. COPPER
C17
D7 C28 L1
B0540
120uH T4
D8
C30
R215
R214
4K7
Q204
R226
MMBTA92
15K0
D204
ES1H
R247
4K7
U201
120uH
D10 B0540
C6
L3
R203
R201
R219
U202
D9
R73
33R
FDT3612
T5
4148
D214
D12
8V2
D14
4K02 R268
8K66
680P
R218
C213
C21
FDT3612
33R
C210
R70
UCC25600
U204 U8
R72
Q13 C31
C5
U2
1U
4U7
R20
LM393D
C16 100N
Q2
TL431A
L2
C11 D3
C8
R202
10R0
100N
100N
C207
C206
43V0
R16
1M0
D28
1M0 R29
22N 560VDC
5217
W201
8
R5
2328
TO INPUT BOARD
D213
R55 R58
R57
1
1 e
ESD
D2
F6
U1
100N C7
1K62 R4
1A25
D1 28K7 R3
C9
WARNING
PLUG CONNECTORS CENTERED
TEST
R56
S/N LABEL
187K
R1
R2
10R
R13
187K T810
300
R223
U205
W1
R43
R35
475K
33K
MMBTA92
R34
475K
200V
R53
10K
D13
W2 W5
Q3
C2
T30 AMP SLO-BLO
Q1
F1
3414
2498
+
T30 AMP SLO-BLO
3414
2498
+
F2
300 W3
W4
SA315S
M1806V03
M1806 V03
Into Wave
SA315S POWER AMPLIFIER
L200
R243
0R02
R242
0R02
RT V
R T V
0R05
R244
5949
3U3
140V
C13
RT V
453UH
6699
CO
+
IL
+
5934
2700U
250V
C216
1N R61
R63
619K
C230
R24
47P
4K7
R62
619K
R259
R258
182K
20K5
U206
R210 20K5
TL331
+
C232
33U
U203
R228
R229
R262 1M0
C235
R261
10U
274K
18V0
100N
U4
100N C231
ZXGD3002E6
33R
R10
1R0
R237 C224
+
R54
182K
100N
ES1H
1U
DNS
10R
22R
DNS
R230
U3
R
V
R
C219
TEST
C228
5986
10U
600V
C3
R
V
R
V
C222
Q203
5949
3U3
140V
C14
+
+
5934
2700U
250V
C229
R52
5225
R60
Q10
2R
4703
470K
R260
R59
D18
F5
HS2
4233 +
2321
IKW75N65EH5
Q205
4233
2321
+
IKW75N65EH5
R
1A25
U200
D5
C227
C4
+
+
R
V
5934
2700U
250V
+
+
5934
2700U
250V
Q8
R49
D16
18V0
4M7
4148
100K0
R51
Q9
C20
220N
MMBTA42
D15
R50
MMBTA42
Q5 R37
470N
R41
1K0
Q4
680P
4124
+
6730
IRF830
D4
C12
SA315S
C15
R
V
R45 D6 R26
HS3
Locating Hole
D
1 2 3 4 5 6 7 8 9 10 11
PCB ASSEMBLY DOCUMENTATION
A
GENERAL ASSEMBLY INSTRUCTIONS
C
B
1. Bend leads on hand placed parts in direction of pad and cut short to less than length of pad.
No exceptions unless approved by Production Engineering.
2. Any clinch parts with longer leads than the length of the pad must be cut shorter either prior to
wave-soldering or afterwards in PCB finishing. No exceptions unless approved by Production Engineering.
3. After Wave apply RTV to all holes indicated and all larger and between tall capacitors.
4. Before tightening screw 8832 on xstr spring 4249 ensure that it is aligned with Q4.
Also silpad 4124 should overhang the edge of the heatsink. See picture below.
12
J
G
H
I
YS#: 8832
DESC: 6-32X1/4 PAN TAPTITE
F
E
MOUNTING HARDWARE INSTRUCTIONS FOR HEAT SPREADER Z1740:
1. First install #8742 screw to align heatspreader Z1740
2. Install all devices, shown in pictures below, on Heat Spreader
TOP VIEW: MOUNTING HARDWARE FOR Q203/Q205:
YS#:8761
DESC: #6-32X1/2"
Q203
YS#: 8800
DESC: #6 KEPS NUT
Q205
YS#: 8902
DESC: 4-40X3/4 PAN
YS#: 8485
DESC: #6 ZINC WASHER
YS#: 4233
DESC: CERAMIC INSULATOR
IMPORTANT!
ADD GOOP ON BOTH SIDES OF CERAMIC INSULATORS
BOTTOM VIEW:
YS#: 4249
DESC: XSTR SPRING
Q4
OVERHANG SILPAD
YS#: 4124
DESC: 1.1x0.82" SIL PAD
YS#: Z1740
DESC: HEAT SPREADER
SEE NOTE 4.
YS#: 8701
DESC: 4-40 KEPS NUT
1st HEATSINK ALIGNMENT SCREW
YS#: 8742
DESC: #4-40X3/8
K
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16
RTV INSTRUCTIONS:
ADD RTV BETWEEN:
C12, C13, C14, AND C15 AFTER WAVE
SOLDER
ADD RTV
17
A
B
C
D
13
Top of Coil L200
E
F
G
H
Ensure that all fastener nubs on tie wraps are well below the top of the coil.
I
J
14
Section:
Product(s):
Assembly Documentation
SA315S
01 PCB#:
Modified:
M1806
2019-05-23
15
Rev#:
File:
V03 EML Rev#:
Assembly.SchDoc
16
Sheet
Tmp Date:
3 Of
17
3
K
J
A
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
C
D
F
H
I
B
E
G
CHANGE HISTORY
#
5
6
7
8
9
10
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
7
8
9
10
11
12
13
3
4
1
2
#
5
6
7
8
9
10
11
12
13
3
4
1
2
.
.
.
..
.
.
.
DATE
08-NOV-2018
06-FEB-2019
27-FEB-2019
14-MAY-2019
VER#
V01
V01
PC#
#9351
#9358
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
V02
V03
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
9380
9384
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
DESCRIPTION OF CHANGE
.
.
.
.
.
RELEASED FOR PRODUCTION
Changed Values, Added D20 and Connected Pin 4 of W201 to Pin 1 of W3
Change Capacitor C229 from #5221 to new #5225 470P 1.6kV
RELEASED FOR PRODUCTION
Replace #8761 heatsink mtg screw with #8835
Add Fuse YS#5136 in series with +Hi net at D6
.
Add Fuse YS#5136 in series with net -Fuse
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
REF
.
.
.
.
.
.
.
.
.
.
.
.
.
FUNCTION
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
POT#
.
.
.
.
.
.
.
.
.
.
.
.
.
STYLE
.
.
.
.
.
.
.
.
.
.
.
.
.
KNOB#
PINOUT DIAGRAMS
1
2
3
4
5
6
7
CASES AND PINS
IRS21844S
IN
SD
VSS
DT
COM
LO
VCC
NC
NC
NC
NC
VB
HO
VS
14
13
12
11
10
9
8
#6686
NJM7815 NJM7915
IRGP50B60PDPBF
IRGP35B60PDPBF
I G O
#6856
G I O
#6857
TO-247AC
G D S
#2496 #2307
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
G
H
I
F
J
14
Section:
Product(s):
Design Information And History
SA315S
01 PCB#:
Modified:
M1806
2019-05-23
15
Rev#:
File:
V03 EML Rev#:
History.SchDoc
16
Sheet 3 Of
Tmp Rev: V028
17
3
K
A
1
B
E
F
G
H
C
D
I
J
K
1
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B
2
Hi+
CAPACITOR DISCHARGE CIRCUIT
SILENT
W750 PIR2001
0R
2010
D1005
CDSF4148
PIR302
PIR301
475K
0805
PIR402
PIR401
COR4
475K
0805
PIR202
PIR201
475K
0805
PIR502
PIR501
475K
0805
PIR2802
PIR2801
COR28
1M0
0805
PIR2102
PIR2101
680R
1206
PIQ201
G
PIR3201
0R
1206
D
PIQ202
S
PIQ203
IRFR825
6834
DPAK3
PIR2202
PIR2201
680R
1206
PIQ101
G
D
PIQ102
S
PIQ103
IRFR825
6834
DPAK3
PIR2302
PIR2301
680R
1206
PIQ601
G
PIQ602
D
S
PIQ603
IRFR825
6834
DPAK3
PIR602
PIR601
COR6
475K
0805
PIR2702
PIR2701
1M0
0805
PIR101
W100
PIR102
475K
0805
PIQ301
PIQ302
PIQ303
MMBTA92
8165
SOT-23
SOT-23
8V2
PIR1302
PIR1301
PIR1402
PIR1401
COR13
475K
0805
COR14
475K
0805
PIR1602
PIR1601
R16
475K
0805
GND
PIR1102
PIR1101
COR11
475K
0805
PIR3301
COR33
0R
1206
PILD201 PILD202
RED
PWR
7033
PIR2602
COR26
1M0
PIR2601
PIR2502
PIR2501
0805
1M0
0805
PIQ501
PIQ503
PIQ502
COQ5
MMBTA42
6847
SOT-23
SOT-23
PIQ401
6847
PIQ402
MMBTA42
PIR2401
W125
PIR2402
1K800
0805
PIR1502
PIR1501
R15
221R
0805
PIR802
PIR801
100R
1206
PIR1802
PIR1801
10K
10K
PIR1201
PIR1202
2K74
0805
PIR1702
PIR1701
330R0
0805
PILD101
PILD102
RED
7033
DISCHARGE
PIR702
PIR701
100R
1206
PIR902
PIR901
COR9
100R
1206
PID302
COD3
PID301
DO-214AC
18V
PIR2902
PIR2901
100R
1206
PIR1002
PIR1001
100R
1206
PIR3002
R30
100R
PIR3001
1206
COR19
1W00
PIR1901
0R
2512
Hi-
Hi+
1W00
PIR3101
0R
2512
TO CAP BOARD
SILENT
Hi-
GND
LEG
1
PIW101COW1:1
2
PIW102COW1:2
3
PIW103COW1:3
4
PIW104COW1:4
5
4
3 4 5 6 7 8 9 10 11 12
J
13
Yorkville Sound Ltd.
Product(s):
550 Granite Court
Pickering, ON
Canada L1W 3Y8 www.yorkville.com
14
SA315S
Short Description Of The Product Description:
PCB#: M1811
Modified: 2019-03-20
15
Rev#: V02
File:
EML Rev#:
Discharge_Circuit.SchDoc
XX
16
Sheet 1 Of
Tmp Rev: V031
17
2
K
C
D
E
F
G
H
I
J
A
1 2 3 4
B
C
D
G
H
I
E
F
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
6
7
8
4
5
9
10
11
12
13
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE
.
.
.
.
.
.
.
.
.
.
DATE
.
07-NOV-2018
20-FEB-2019
#
10
11
12
13
6
7
8
9
3
4
5
1
2
#
6
7
4
5
1
2
3
10
11
8
9
12
13
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
V01P2
V02
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
RELEASE FOR PRODUCTION
RELEASE FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
REF
.
.
.
.
.
.
.
.
.
.
.
.
.
FUNCTION
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
POT#
.
.
.
.
.
.
.
.
.
.
.
.
.
KNOB#
PINOUT DIAGRAMS
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Design Information And History
SA315S
Product(s):
PCB#: M1811
Modified: 2019-03-20
15
Rev#:
File:
V02 EML Rev#:
History.SchDoc
16
XX Sheet 1 Of
Tmp Rev: V031
17
*
K
I
COTITLE1
PAHW200 PAHW300
SINGLE LAYER
1 OZ.PCB
1.5mm ALUMINUM
PAW104 PAW103
PAD102
8V2
PAD101 PAD103
PAR1601 PAR1602 PAR1401 PAR1402
PAR2001
0R
PAW102 PAW101
7994
COW1
PAW105
PAR1901
PAQ103
COR33
PAR3301
PAR2802
COR28
PAQ302
PAQ303
PAQ301
PAR102
PAR101
PAR2702
COR27
PAQ503
MMBTA42
PAQ501 PAQ502
PAR2501 PAR2502
COR25
PAR2401 PAR2402 COR24
PAQ101
PAR3001
PAR3101
0R
COTH1
PATH100
COHW9 COSNL2
PAQ603
PAQ601
PAQ203
PAQ201
0R PAR3201
COR8
COR18
PAR3002
PAQ402 PAQ401
PAR1801
MMBTA42
PAQ403
R12
R17
PAR1202
PAR1702
PAR1802 PAR1201
PAR1701
PALD101
PALD102
PAD302
18V
PAD301
COHW4
COR15
PAHW900
PALD201 PALD202
PAR202 PAR201 PAR502 PAR501
COTH2
POWER ON
INDICATING LED
PATH200
PAHW400
D
E
F
G
H
I
J
K
1
C
B
A
1 2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13
1. INSPECT SOLDER JOINTS AFTER REFLOW
2. USE PIZZA CUTTER TO SEPARATE BOARDS FROM PANEL.
14 15 16 17
A
B
C
2 3 4 5 6 7 8 9 10 11 12 13
J
14
Section:
Assembly Documentation
SA315S
Product(s):
PCB#: M1811
Modified: 2019-03-20
15
Rev#:
File:
V02 EML Rev#:
Assembly.SchDoc
16
XX Sheet 2 Of
Tmp Rev: V031
17
4
K
F
G
H
I
D
E
J
A
1 2 3 4
B
C
D
G
H
I
E
F
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
6
7
8
4
5
9
10
11
12
13
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE
.
.
.
.
.
.
.
.
.
.
DATE
.
07-NOV-2018
20-FEB-2019
#
10
11
12
13
6
7
8
9
3
4
5
1
2
#
6
7
4
5
1
2
3
10
11
8
9
12
13
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
V01P2
V02
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
RELEASE FOR PRODUCTION
RELEASE FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
REF
.
.
.
.
.
.
.
.
.
.
.
.
.
FUNCTION
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
POT#
.
.
.
.
.
.
.
.
.
.
.
.
.
KNOB#
PINOUT DIAGRAMS
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Design Information And History
SA315S
Product(s):
PCB#: M1811
Modified: 2019-03-20
15
Rev#:
File:
V02 EML Rev#:
History.SchDoc
16
XX Sheet 1 Of
Tmp Rev: V031
17
*
K
I
1 2 3 4 5 6 7 8 9 10 11
A
G
H
B
INPUT
J1
INPUT
XLR FEML
4010
2
1
3
SG1
SG2
C
E
D
Male XLR
J2
THRU 1
THRU 1
4140
F
J3
THRU 2
THRU 2
Male XLR
4140
SG3
SG4
SG5
SG6
3
XLR-ONE-GND
4
R1
265V
48R
5
R2
W100
100R
0805
250V
470P
C2
0603
250V
470P
C1
0603
B
R4
39K2
0805
4
2357
3
4 W2:4 IGND
4 W2:3
XLR-ONE-GND
2
4 W2:2
-SIG
1
4 W2:1
+SIG
C
R3
W100
100R
0805
D
L1
15UH
7967
1
HC1 HC2
1
CON_HOLE_156
16AWG
.
W1
BLK
PREFUSED WIRE
CON_HOLE_125
IGND
IGND
E
F
6
G
Section:
Product(s):
INPUT JACK
SYNERGY
PCB#: M1813
Modified: 25/10/2018
7
Rev#:
File:
8
V01 EML Rev#:
Input.SchDoc
9
XX Sheet 1 Of 2
10
Tmp Rev: V032
11
H
1 2
A
A
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
B
CHANGE HISTORY
C
D
E
F
G
H
I
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
7
10
11
8
9
12
13
5
6
1
2
3
4
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
10
11
12
13
7
8
9
5
6
1
2
3
4
#
6
7
8
9
10
11
12
13
3
4
5
1
2
DATE
.
.
.
.
.
.
.
.
.
.
.
.
22-OCT-2018
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION.
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
J
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
K
1 2 3 4 5 6 7 8 9
14 15 16 17
A
B
C
D
E
F
G
10 11 12 13
J
14
Section:
Product(s):
Design Information And History
SYNERGY
XX PCB#: M1813
Modified: 25/10/2018
15
Rev#:
File:
V01 EML Rev#:
History.SchDoc
16
Sheet 2 Of
Tmp Rev: V032
17
2
K
H
I
A
1
B
2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13 14 15 16 17
A
B
C
D
E
F
J
K
1
1. PCBSA: R1 #6543 IS HAND INSERTED.
G
H
THIS SHEET CONTAINS SPECIAL PRODUCTION NOTES AND A LIST OF PCB HARDWARE PARTS REQUIRED FOR THE BUILD.
I
2 3 4 5 6 7 8 9 10 11 12 13
J
14
Section:
Product(s):
Assembly Documentation
SYNERGY
XX PCB#: M1813
Modified: 12/11/2018
15
Rev#:
File:
V01 EML Rev#:
Assembly.SchDoc
16
Sheet 1 Of
Tmp Rev: V032
17
*
K
C
D
E
F
G
H
I
A
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
B
CHANGE HISTORY
C
D
E
F
G
H
I
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
7
10
11
8
9
12
13
5
6
1
2
3
4
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
10
11
12
13
7
8
9
5
6
1
2
3
4
#
6
7
8
9
10
11
12
13
3
4
5
1
2
DATE
.
.
.
.
.
.
.
.
.
.
.
.
22-OCT-2018
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION.
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
J
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
K
1 2 3 4 5 6 7 8 9
14 15 16 17
A
B
C
D
E
F
G
10 11 12 13
J
14
Section:
Product(s):
Design Information And History
SYNERGY
XX PCB#: M1813
Modified: 12/11/2018
15
Rev#:
File:
V01 EML Rev#:
History.SchDoc
16
Sheet 2 Of
Tmp Rev: V032
17
2
K
H
I
C
D
E
F
A
1
B
G
H
1
2
2
3
3
4
4
5 6
4140
J1
2
3
1
.
Male XLR
1
2
3
3 W1:1
3 W1:2
3 W1:3
5 6
7 8 9 10 11
A
B
C
D
E
F
G
7
Section:
Product(s):
SA221S-LINEOUT
SA221S
PCB#: M1831
Modified: 2021-04-14
Rev#:
File:
V01 EML Rev#: XX
SA221S-LINEOUT.SCHDOC
8 9 10
Sheet 1 Of
Tmp Rev: V032
11
2
H
A
B
C
D
E
F
G
H
I
J
1 2 3
CHANGE HISTORY
4
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
4
5
6
1
2
3
10
11
12
7
8
9
13
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
8
9
10
11
12
13
5
6
7
3
4
1
2
#
1
2
3
4
5
6
7
8
9
10
11
12
13
DATE
.
.
.
.
.
.
.
.
.
.
.
.
April-14-2021.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
Released for Production
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
PINOUT DIAGRAMS
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
K
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17
A
B
C
D
E
F
G
H
I
J
14
Section:
Product(s):
Design Information And History
SA221S
PCB#: M1831
Modified: 2021-04-14
Rev#:
File:
V01 EML Rev#:
History.SchDoc
XX Sheet 3 Of
Tmp Rev: V032
15 16 17
3
K
B
A
1 2 3 4
SPECIAL PRODUCTION NOTES
5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13 14 15 16 17
A
B
G
H
E
F
C
D
Gap Pad #4236 (2)
Screw #8741 (4)
I
J
THIS SHEET CONTAINS SPECIAL PRODUCTION NOTES AND A LIST OF PCB HARDWARE PARTS REQUIRED FOR THE BUILD.
K
1 2 3 4 5 6 7 8 9 10 11 12 13
I
J
14
Section:
Product(s):
Assembly Documentation
SA221S
PCB#: M1831
Modified: 2021-04-14
Rev#:
File:
V01 EML Rev#:
Assembly.SchDoc
XX
15 16
Sheet * Of
Tmp Rev: V032
17
*
K
G
H
E
F
C
D
A
B
C
D
E
F
G
H
I
J
1 2 3
CHANGE HISTORY
4
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
4
5
6
1
2
3
10
11
12
7
8
9
13
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
8
9
10
11
12
13
5
6
7
3
4
1
2
#
1
2
3
4
5
6
7
8
9
10
11
12
13
DATE
.
.
.
.
.
.
.
.
.
.
.
.
April-14-2021.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
Released for Production
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
PINOUT DIAGRAMS
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
K
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17
A
B
C
D
E
F
G
H
I
J
14
Section:
Product(s):
Design Information And History
SA221S
PCB#: M1831
Modified: 2021-04-14
Rev#:
File:
V01 EML Rev#:
History.SchDoc
XX Sheet 3 Of
Tmp Rev: V032
15 16 17
3
K
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
J
I
B
POWER SUPPLY SA221S
C
H
G
F
D
E
BLK 2 a
YS#2444
Thermal Breaker
1 BLK
S6
2 a
YS#3587
DPST Switch
1
BLK
WHT 4
S2
3
WHT
IEC_RECT a
YS#4138
AC IN
W1:1 2
1
2 PIN
W1:2 2
2 PIN
2
BLK
WHT
W1 a a
K2:2
D13
4007
1000V
RELAY 1C-
Q3
TO92
2N6517
6854
R1
NTC
2504
2R a a
R2
NTC
2504
2R
R3
NTC
30AMP
2504
2R
RELAY 1C-
D11
4007
1000V
R4
NTC
2504
2R
BLK
C1
250V
100N
'X2' 18MM
L1
1500UH
3817
D12
4007
1000V
WHT
.
R12
120K
C32
C33
RAD .2in
22U
50V
Q4
10X13MM
10U
160V
R16
W250
.
220K
BC550C
5101
TO92
.
R13
330K
.
R14
130K
.
R15
130K
.
R17
100K
C34
13x19
10U
450V
C2
250V
680N
X2 27MM
EC2
1
C6
250V
4N7
'Y' 10MM
CON_HOLE_189
CHASSIS GND
AC BOARD
120V
6
6 W3:6
5
6 W3:5
4
6 W3:4
3
6 W3:3
2
6 W3:2
1
6 W3:1
1
2
3
4
5
6
6
6 W6:6
5
6 W6:5
4
6 W6:4
3
6 W6:3
2
6 W6:2
1
6 W6:1
2nd 120V
1
2
3
4
5
6
BLU
150°C
BRN
YEL/BLK
BLK
WHT
VIO
GRY
RED
YEL
RED
GRY
VIO
BLU
150°C
BRN
YEL/BLK
BLK
WHT
YEL
RED
GRY
VIO
VIO
GRY
RED
1
2
3
4096
4
T2 a
XFMR-SEC-HI
1
2
3
3575
3
2
1
3 W4:3
3 W4:2
3 W4:1
1
2
3
4096
4
1
2
3
4
4 W7:1
4 W7:2
4 W7:3
4 W7:4
XFMR-SEC
XFMR-SEC-HI
1
2
3
3575
3
2
1
3 W8:3
3 W8:2
3 W8:1
XFMR-SEC a
T3
3
4
1
2
4 W9:1
4 W9:2
4 W9:3
4 W9:4
D3
4007
1000V
D4
4007
1000V
R5
W500
.
470R
R6
W500
.
470R a
CRITICAL SAFETY COMPONENTS
THIS SYMBOL IS PLACED ADJACENT TO
SAFETY CRITICAL COMPONENTS.
C5
10X13MM
100U
63V
PSGND
B
D1
6775
BRIDGE
SIP
600V
EC3
CHASSIS GND
POWER
BOARD
1
CON_HOLE_189
D2
6775
BRIDGE
SIP
600V
C
PSGND
-Hi
C4
250V
100N
RAD POLY
PSGND
C3
250V
100N
RAD POLY
+Hi
SILENT
1
5 W5:1
2
5 W5:2
3
5 W5:3
4
5 W5:4
5
5 W5:5
D
E
TO CAPACITOR BOARD
F
N1
N2 HS
G
K1:2
3696
RELAY 1C
K1:1
3696
RELAY 1C
H
I
J
K
1 2 3 4 5 6 7 8 9 10 11 12 13
Yorkville Sound Ltd.
550 Granite Court
Pickering, ON
Canada L1W 3Y8 www.yorkville.com
14
Product(s):
Description:
PCB#: M1832
SA221S
SA221S
Modified: 2021-06-09
15
Rev#: V03
File:
EML Rev#:
M1832.SchDoc
16
01 Sheet 1 Of
Tmp Rev: V032
17
4
K
J
A
B
C
D
E
F
H
I
G
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
6
7
8
3
4
5
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
7
8
9
10
11
12
13
3
4
1
2
#
9
10
7
8
11
12
13
3
4
5
6
1
2
DATE
.
.
.
.
.
.
.
.
.
09-MAR-2020
03-DEC-2020
.
09-Jun-2021
VER#
.
.
.
.
.
.
.
.
.
V01
V02
.
V03
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
RELEASED FOR PRODUCTION
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
MJE15032 (YS#6808)
TO-220
E C B
MJL21194 (YS#6988)
TO3P
E C B
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
14
Section:
Product(s):
PCB#:
Design Information And History
SA221S
M1832 Rev#: V03 EML Rev#: 01 Sheet 4
Modified: 2021-06-09
15
File: History.SchDoc
16
Of
Tmp Rev: V032
17
4
K
J
I
(8325X5000)
Score
FIDUCIAL
INS1
Score
CLINCH
ORIGIN
FIDUCIAL
INSERT
VCD
ORIGIN
79mil(2mm) Rad ~ 4 PLACES
SA221S
M1832 V03
1
W7
4151
XFMR-SEC-HOLDER
D2
AC BRIDGE BOARD FOR POWER SUPPLY
TEST
SA221S
WHT
W4
R
T
V
C1
3817
R
T
V
BEC1
BEC
C34
LOC
4146
300
L1
C2
5266
680N
250V
R
T
V
C33
RT V 5959
10U
450V
22U
C 2020
RT V Q4
K1
6451
R
T
V
250V
BC550C C6
3696
R T V 2N6517
Q3
120K
S/N LABEL
R12
5914
R TV
4146
R TV
300
W5
100U
63V C5
4243
R5 R6
1 W3
470R 470R
300
W8
W9
6438 D3
4151
6438
1
XFMR-SEC-DISCHARGE
D4
XFMR-PRIMARY 120V
4243
W6
1
5629
10U
160V
C32
4263
C1
AC IN
1
BLK
W1
RT V
C2
3019
4007
T V
R T V
R1 R2
M1832 1/2
R3
NC
NO
D13
R T V
R4
FIDUCIAL
INSERT
SECONDARY
E
F
G
H
I
J
K
1
A
1 2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13
B
1. RTV between tall components and where indicated
2. When applying RTV to R1-R4, it should only be placed along the tops of the varistors.
D
C
PTCs R1, R2, R3, R4
Add nylon spacer YS#8663 to PTCs YS#2504 a shown in the picture below.
14 15 16 17
A
B
C
D
2 3 4 5 6 7 8 9 10 11 12 13
J
14
Section:
Product(s):
Assembly Documentation
SA221S
PCB#: M1832
Modified: 2021-06-09
Rev#:
File:
V03 EML Rev#:
Assembly.SchDoc
01
15 16
Sheet 2 Of
Tmp Rev: V032
17
4
K
I
E
F
G
H
J
F
I
A
B
C
D
E
G
H
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
6
7
8
4
5
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
7
8
5
6
11
12
13
3
4
1
2
#
5
6
7
8
9
10
11
12
13
3
4
1
2
DATE
.
.
.
.
.
.
.
.
.
09-MAR-2020
03-DEC-2020
.
09-Jun-2021
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
V01
V02
.
V03
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
RELEASED FOR PRODUCTION
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
MJE15032 (YS#6808)
TO-220
E C B
MJL21194 (YS#6988)
TO3P
E C B
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
PCB#:
Design Information And History
SA221S
M1832
Modified: 2021-06-09
Rev#:
File:
V03 EML Rev#:
History.SchDoc
01 Sheet 4 Of
Tmp Rev: V032
15 16 17
4
K
I
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B
E
F
G
I
J
K
C
D
H
SUBWOOFER AMP
PILink301 PILink302
+15VS
100N
0805
PIC21202
PIC20202
PIC20201
50V
0805
100N
PIC21201
50V
LVGND
100N
100N
PIC20901
PIC20902
PIC20301
PIC20302
+15V_MOD
50V
0805
50V
0805
100N
100N
PIC21002
PIC20402
PIC20401
50V
PIC21001
50V
0805
0805
100N
100N
PIC21102
PIC21101
PIC20502
PIC20501
50V
0805
50V
0805
100N
PIC23302
50V
PIC23301
0805
100N
PIC23401
50V
PIC23402
0805
+15VS
WOOFGND
+15V_MOD
PIN121101
COR200
PIR20002
W125
PIR20001
+/-15V_MOD
0805
10R0
100N
PIC20601
PIC20602
50V
COC206
0805
100N
PIC20701
PIC20702
50V
COC207
0805
LVGND
PIN121201
-15V_MOD
W125 PIR20202
CON1212
0805
10R0
-15VS
+15VS
100N
PIC20001
PIC20002
50V
COC200
0805
WOOFGND 100N
PIC20801
PIC20802
50V
COC208
0805
-15VS
Grounds i
LVGND
PILink201 PILink202
PILink402
COLink4 i
PILink501
Grounds i
PILink502
PSGND WOOFGND
-15VS
CON_HOLE_189
-15V_MOD
LVGND
PIR20301 W100 PIR20302
0805
10K0
PSGND
FROM INPUT PCB
W100 PIR20402
0603
12K1
+15V_MOD
PIR21402
8
W201:2 8
W201:3 8
W201:4 8
W201:5 8
W201:6
8
W201:7 8
W201:8 8
5
W4:2 5
W4:3 5
W4:5 5
PIN120401
PIN120101
PIN120801
PIN120201
PIN120301
LVGND
OC
+Hi_Fused
W125 PIR5502
49K9
0805
Hi
W125 PIR5602
49K9
0805
Hi
Hi
+15V_MOD i
PIR21502
PIR21501
47K5
0805 i
PID21302
PID21301
PIR5701 W125 PIR5702 PIR5801 W125 PIR5802
D213
SOT-23
15V0
49K9
COD213
49K9
0805 i
PIR21902
PIR21901
475R0
0805
LVGND
PIN120701 POLVGND2
CON1207
WOOFGND
PIN120601
W4:4 5
4
PIW404
+15VS
PIN120501
CON1205
-15VS
CAPACITOR BANK
PIC2902
PIC2901
1210
PIC3202
PIC3201
PIC21702
470P
PIC21701
50V
0603
WOOFGND
1210
PIC3302
PIC3301
Hi i
1210
PIC3402
PIC3401
1210
-
PIR20101
W100
PIR20102
12K1
0603
PIU20104 PIU20106
-15V_MOD
1
PIEC101
CON_HOLE_189
+15V_MOD
+
PSGND
PIU20108 PIU20105
PIR23301 PIR701
PIR22301 1/8W PIR22302
0805
6K98
+15V_MOD
0805
PIR23302
6K98
PIR702
0805
6K98
2
-
PIU20508
COU205:2
DUAL OPAMP
50V
PIC22001
220N
1206
PIC22002 2
-
PIC22501
COC225 50V
470P
0603
PIC22502
PIR23602
COR236
6K98
0805
PIR23601
3
+
PIU20504
7817
MC33078D
-15V_MOD
W100 PIR23102
0805
1K0
PIR23201 W100 PIR23202
3
+
0805
1K0
100V
PIC22601
47N
1206
PIC22602
PSGND
PIR21401
4K7
0805
Hii
SILENT ON/OFF
SILENT
PIC1201
PIC1202
PIU20107
PIU20101
LM311
7851
SO8
Hi i
250V
3300U
40X80MM
PIC1302
PIC1301
U204:1
DUAL OPAMP
MC33078D
7817
+Hi
40X80MM
3300U
250V
PIC1401
PIC1402
250V
3300U
40X80MM
PIC1502
PIC1501
40X80MM
3300U
250V
PIR22202
10K0
0805
W125 PIR21802
0805
8K66
680P
0805
50V
+15V_MOD
PIR22201
D1005
PIR26801 W125 PIR26802
CDSF4148
4K02
0805
6
-
PIU20408
U204:2
DUAL OPAMP
PIR22102
5
+
PIU20404
7817
MC33078D
PIR22101
470R
0805
-15V_MOD
10U
PIC24201
16V PIC24202
1206
PIR801 W125 PIR802
0805
4K02
WOOFGND
0805
1N
COC218
PIC21801
50V
W125 PIR22402
0805
47R
PIR22701 W100 PIR22702
0805 1M0
6
-
MC33078D
U205:2
DUAL OPAMP
7817
7
5
+
PIN401
PID502
PID501
ES1J
DO-214AC
PIN701
PID402
PID401
ES1J
DO-214AC
PIR25902
PIR25901
182K
0805
PIR25802
Hii
PIR24002
PIR24001
470R
0805
WOOFGND
PIR25801
20K5
0805
PIR26102
PIR26101
274K
0805
PIR26002 COR260
PIC23501
10U
0805
PIR26001
470K
Hii
PIC23502
10V
0805
-
+
PIU20605
PIU20602
Hii
+Hi
PIR6302
W250 PIR23002
1206
DNS
Hi i
PIR26201 W100 PIR26202
1M0
0805
8163
+15V_MOD
+
-
PIU20208 PIU20205
PIU20204 PIU20206
-15V_MOD
TL331
COU206
SOT23-5
PIC21602
50V
PIC21601
0805
1N
PIU20207
PIU20201
LM311
7851
SO8
PIQ20401
WOOFGND
PIR21002
COR210
PIR21001
0805
20K5
PIC23001
+15V_MOD
PIC23002
47P
50V
0805
619K
PIR6301
1206
1
PIU301
Hi i
+Hi
Hi+ i
PIR22602
15K0
PIR22601
0805
PIQ20403
PIQ20402
MMBTA92
8165
SOT-23
PID20401
PID20402
ES1J
PIR24702
PIR24701
4K7
0805
PIR2402
PIC23201
PIR2401
4K7
0805 33U
PIC23202
25V
6x6mm
+15V_LS
PIR6102
619K
PIR6101
1206
PIR6202
619K
PIR6201
1206
Hii
PIR23702 PIR23701
1R0
2512
Hii
ES1J
DO-214AC
2
IN1
5
IN2
PIR902
33R
PIR901
0805
Hi i
Hi i
VCC
SINK
SOURCE
SOT23-6
GND
3
PIU303
ZXGD3002E6
7949
PIC22101
100N
COC221
100V PIC22102
1206
PIC22401
1U PIC22402 50V
4X4mm
PIZD20002
PIZD20001
PIR22901 W250 PIR22902
1206
10R
1206
22R
SOD123
DNS
PIR23402 PIR23401
182K
0805
18V0
SOD-323
PIR22502 PIQ20301
PIC23101
100N
PIC23102
50V
0805
IRS21844S
7
VCC HO 12
VB
13
1
IN
2
SD
4
DT
3
VSS
Hi i
COM 5
LO
6
Hii
Hi-
PIR1002
W125
PIR1001 i
33R
0805
Hii +15V_LS
2
IN1
PIR2301 W250 PIR2302
1206
DNS
1
PIU401
VCC
SINK
Hii
6686
SO14
Hii
PIR2502
10K0
PIR2501
0805
1206
10R
COD21
PIR24902
SOD123
5
IN2
SOT23-6
SOURCE
1206
GND
3
PIU403
ZXGD3002E6
22R
7949
2321
T0247
IKW75N65EH5
Hi-
COQ205 PIQ20502 i
+15V_LS
PIR25102
100N
PIC2201
PIQ20501
100V PIC2202
1206
PIQ20503
PIQ20302
PIQ20303
IKW75N65EH5
Hi i
T0247
2321
PIR5902
.
PIR5901
2R
PIR6002 i Hi
.
PIR6001
2R i Hi
PIC22201
PIC22202
PIC22301
PIC21901
PIC21902
680N
400V
600V
10U
RAD POLY
PIC22302
600V
10U
RAD POLY
PIC301 PIC401
PIC302
140V
3U3
RAD POLY
OP i
PIC402
PIL20002 PIL20001
453UH
6699
PIR24202 PIR24302
PIC22801
400V
COC228
680N
PSGND
PIC22802
PIR1202
PIR101
W125
PIR102 PIR1101
W125
PIR1102
187K
0805
187K
0805
PIR24201
0R02
187K i
PIL402
2919
0.18UH
PIR1201
0805
0R02
PIR24301
OARS
COC4
RAD POLY
140V
3U3
PIR24402
PIR24401
0R05
OARS
11mm
PIL401
W125 PIR23802
0805
33R
COC227
100N
PIC22701
50V
0805
PIC22702
OP i
Hii
PIC2301
PIC22902
PIC22901
1600V
470p
PIC2701
PIR1302
PIR1301
187K
0805
187K
0805
T810-600G-TR
7915
PIQ102
D2PAK
PIQ302 TO92 PIQ303
10R
1206
MBS4992
5190 {Voltage}
PIR1402
PIQ101
1206
PIC102
PIC101
PIC3502
PIC3501
1210
PIC3601
PIC3602
1210
PSGND PIC2302
1210
PIC2702
1210
10U 16V
5X5.5mm
PIC2801
-Hi
W125 PIR25502
0805
82K5
0805
82K5
PIR25602
CHSGND
CON_HOLE_189
PIC2802
1210
RED
CON_HOLE_140 CON_HOLE_140
1 2 3 i
Hi-
4 i
Hi-
5
-Hi
PIN801
6 7 8
4
3
2
1
RED
BLK
BLK
9 10
WOOFER
YS #7028
11 12
CON_HOLE_140
CHSGND
13 14
PSGND
6668
4PIN SMT
Section:
Product(s):
Woofer Amp
SA115S/SA221S
PCB# M1833
Date Modified:
Rev#
2022-01-28
V01 BOM Rev#
Filename:
01 Sheet
Amp.SCHDOC
15 16
LTV-8141S
4
PIW504 4
3
4
2
4
1
4
W5:4
W5:3
W5:2
4
4
3
PIW103 4
2
4
1
4
W1:4
W1:3
W1:2
4
PIW204 4
3
4
2
PIW202 4
1
4
W2:4
W2:3
W2:2
1 Of
17
3
D
G
H
E
F
I
J
K
C
A
B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B
E
F
G
I
J
K
C
D
H
Hii
+Hi
PIF602
PIF601
1A25
5136
+Hi_Fused i LNK
Hii
PIL702
7967
PIL701
Hii
MURA260
403D
Hii
+15V_LS
PIC902
PIC901
1210
MC7815BDTG
PIQ1301 IN
GND
PIQ1302
OUT
7846
DPAK3
PIQ1303
Hii
PIC2402
PIC2401
1210
OC
PIN301 PIR5301 W250 PIR5302
10K
0805
TURN ON VOLTAGE
FROM POWER SUPPLY
(OPEN COLLECTOR)
PIC2101
PIC2102
1206
SOD-323
200V
SOD-323
200V
33K
0805
PIR3501
PIQ702
PIQ701
SOT-23 MMBTA92
PIQ703
8165
+Hi
PIR4402 PIR4401
475K
0805
CAPACITOR BANK #2
W3:2
W3:3
3
3
3
3
PIW303
CON_HOLE_189
PSGND
PSGND
PSGND
PSGND
PIR4702
2N7002
PIR4701
28K7
0805
W125
PIQ803
D
G
PIQ801
SOT-23
7986 PIQ802 S
PID1702
PID1701
PIQ1002
SOT-23
8V2
SOT-23
PIQ1003
PIQ1001
8165
MMBTA92
D1005
CDSF4148
PIC2001
1206
PIC2002
220N
50V
PIR4901 W125 PIR4902
4M7
0805
PID1901
PID1902
D1005
CDSF4148
PIQ903
PID2302
PID2301
SOD-323
18V0
PIR5102
SOT-23 PIQ902
100K0
PIR5101
0805
PSGND
PIR4602
PIR4601
475K
0805
PIR4802
PIR4801
475K
0805
PIQ901
MMBTA42
6847
3
PIU20003
4PIN SMT
6668
LTV-8141S
HiHii i
PIR8002 PIR8001 SILENT PIR7902 W125
SOT-23 i
100K
0805
100K
0805 43V0
Hi-
TO POWER AMP PCB
PIR4301 W100 PIR4302
475K
0805
PIR4502
W100
PIR4501
475K
0805
PID1402
PID1401
SOT-23
8V2
PIR5002
PIR5001
1M0
0805
PIQ603
SOT-23
PIQ602
PSGND
PIQ601
COQ6
MMBTA42
6847
BUSS PUMPING
SHUTDOWN
VDD
RESET
100K
0805
PIR7501
3
OUT
TRIG
THR
CONT
DIS
5
PIU505
7
TLC555
GND
7836
SO8
PSGND
PIC4001
PIC4002
1206
W100
PIR8102
1M0
PIR8101
0805
PID1602
PID1601
SOT-23
8V2
10U
PIC3801
16V PIC3802
1206
100K
0805
PIC4102
PIR5402
50V
PIC4101
0805
1N
1M0
PIR5401
0805
PSGND
PIQ1503
COQ15
MMBTA42
6847
PIQ1501
PIR6401
SOT-23 PIQ1502
PIR7601
PIR6602 PIR6601
100K
0805
SOD-323
18V0
SOD-323
18V0
10U
16V
PIC3901
PIC3902
1206 PIQ1401
PSGND
PIQ1402
PIQ1403
COQ14
MMBTA42
6847
PIR7602
475K
0805
PSGND
-Hi
100K
0805
PIR6501
PIR7801
PIR7802
475K
0805
+Hi
PIR6701
475K
PIR6702
0805
PIR7101
475K
PIR7102
0805
PIR7701
PIR7702
475K
0805
PIC4202 PIR5202
50V
PIC4201
0805
1N
PIR5201
DNS
0805
PSGND
1
Hi
Hi
Hi i
MURA260T3 i
PID201
PID202 i
PIR501
403D
PIR502
10R
1206
Hi
PIU104 i
PIU103
D
LNK306G
0805
100N
50V
S
S
S
S
1
2
7
8
PIC1001
PIC1002
PP RAD
560VDC
22N
8158
SMD8B
Hi i
Hi i
PIR301
W125
PIR302
28K7
0805
PIR401
1K62
PIR402
0805
PID302
PID301
MURA260T3
403D
2
+Hi_Fused
3
-HI
Hi i
ES1J
DO-214AC
PIL202
7974
1000UH
Hii
W250 PIR2902 W250 PIR1602 W250 PIR1702 W250 PIR1802
1M0
1206
1M0
1206
1M0
1206
1M0
1206
4
PIL201
PIC1101
PIC1102
1210
5
151mA
+31V
31.3V
PID2802
PID2801
SOT-23
43V0
PIC 6
PIC 7
PIC 6
PIC 5
PIC802
PIC801
6x6mm
47U
35V
PIR1502
PIR1501
140K0
0805
6
PIR2102
PIR2101
6K20
0805
W100 PIR2202
1M0
0805
PIR2002
33K
PIR2001
0805
8
PIU208
V+
7661
V-
4
PIU204
U2:3
LM393D
SO8
7
SO8
PIU207
7661
LM393D
U2:2
7
-
+
Hii
8
+15V_LS
PIR7002
PIC3101
PIC3102
COC31
1210
4U7
50V
PIR7001
1K27
0805
PIR602
PIR601
15K0
0805
PIR1902
6K20
PIR1901
0805
PIR3001
1K27
PIR3002
0805
2V5
PIC1602
COC16 C16
PIQ202
PIQ203
PIQ201
7720
TL431A 0805
PIC1601
100N
50V
SOT23
-
+
SO8
1
7661
LM393D
2
RT
1
DT
PIC501
PIC502
1206
4
SS
9
PIU806
PIU807
UCC25600
7987
SO8
GD2
GD1
Hii
Hii
50V
Hii
1210
4U7
Hii
OC
PIR7202
PIR7201
1K0
0805
UNDER VOLTAGE SHUT DOWN MAY NOT NEED
+Hi
PIR3402
475K
PIR3401
0805
10
XF3955
11
Hii
PIR7301
W250
33R
1206
33R
1206
G
G
D
PIQ1102
S
PIQ1103
FDT3612
6977
SOT233
Hii
PIQ1202
D
S
PIQ1203
FDT3612
6977
SOT233
12
PIC2601
PIC2602
1210
13
XF3955
14
SOD123
B0540
SOD123
B0540
+15V
100N
100V
PIC3701
PIC3702
1206
22U
16V
PIC1701
PIC1702
PIL102
120uH
8101
COC17
5X5.5mm
PIL101
+15V_MOD
SOD123
B0540
SOD123
B0540
100N
PIC3002
100V
PIC3001
1206
22U
PIC601
C6
PSGND
COC6
COL3
16V
PIC602
PIL302
120uH
8101
PIL301
-15V
+Hi
PIF502
5136
1A25
PIF501
PID601
PID602
SOD-323
18V0
PIR2702
+Hi_Dis
DISCHARGE RAILS
PIR2701
475K
0805
PIR2802
475K
PIR2801
0805
PIR3202
PIR3201
475K
0805
PIR4202
PIR4201
475K
0805
PIC1802
470N
PIC1801
100V
1206
PIR3702
PIR3701
475K
0805
D
PIQ402
Hi i
PIR4102
S
PIQ403
PIR4101
1K0
0805
SOD-323
18V0
PIC1902
PIC1901
0805
SOT-23
PIQ503
COQ5
PIQ502
PIQ501
6847
MMBTA42
PIR3902
HEATSINK
BLEEDER CIRCUIT
1M0
PIR3901
0805
W100
2K0
0805
PIR3802
PIR4001
10R0
PIR4002
0805
IRF830
N
TO220
6730
-15V_MOD
PIR2602
475K
PIR2601
0805
PIR3102
475K
PIR3101
0805
PIR3302
475K
PIR3301
0805
PIR3602
COR36
475K
PIR3601
0805
-Hi
Section:
Product(s):
Power Supply
SA115S/SA221S
PCB# M1833
Date Modified:
Rev#
2022-01-28
V01 BOM Rev#
Filename:
01 Sheet
Supply15V.SCHDOC
2
15 16
Of
17
3
C
D
G
H
B
E
F
I
J
K
A
J
A
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
B
C
D
E
F
H
I
G
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
7
8
9
10
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
5
6
7
8
3
4
1
2
# DATE
.
.
.
.
.
.
.
.
9
10
11
12
13
6
7
8
1
2
3
4
5
.
.
24-NOV-2020
28-JAN-2022
VER#
.
V01
PC#
.
9667
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
.
Changed C213 YS#7603 680p 5% to YS#9048 680p 1%
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
REF
.
.
.
.
.
.
.
.
.
.
.
.
.
FUNCTION
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
POT#
.
.
.
.
.
.
.
.
.
.
.
.
.
STYLE
.
.
.
.
.
.
.
.
.
.
.
.
.
KNOB#
PINOUT DIAGRAMS
CASES AND PINS
1
2
3
4
5
6
7
IRS21844S
IN
SD
VSS
DT
COM
LO
VCC
NC
VB
HO
VS
NC
NC
NC
14
13
12
11
10
9
8
#6686
MC7815
I G O
#7846
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11
14
12 13
15 16 17
A
B
C
D
E
F
G
H
14
Section:
Product(s):
Design Information And History
SA115S/SA221S
01 PCB#: M1833
Modified: 2022-01-28
15
Rev#:
File:
V01 EML Rev#:
History.SchDoc
16
Sheet 3 Of
Tmp Rev: V028
17
3
K
J
I
COCNR4
COTLH4
PATLH400
Into Wave
#8835+
#8800
COPF4
PAPF400
COXC4
PAC2801
PAC2802
COC28 PAF602
0 30
COXC5
PAW103
PAW102
3 OZ. COPPER
COEC3
COEC9
PAEC301
PAXC400
PAEC300
PAW104
PAC1701
PAR21501
PAD802 PAC3702
PAR21502
Q204
PAQ20402
MMBTA92
PAQ20401 PAQ20403
PAT404 PAT403 PAT401
PAD801 PAC3701
PAL102
120uH
PAL101 PAD2002
PAC1702
COD20
PAD2001
COC203 PAC20301 PAU20108
PAC20302
PAU20107 PAU20106 PAU20105 COC205
PAC20501
PAC20502
PAU20208 PAU20207 PAU20206 PAU20205
PAT405 PAT406 PAT408
D8
C30
PAD902 PAC3002
PAD901
PAC3001
PAC601
PAL302 PAL301
120uH
PAU20201 PAU20202 PAU20203 PAU20204
COC211
PAC21101
PAC602
PAC702 C7
PAC902 PAR402 R4
PAC21102
D10 PAD1002 PAD1001
PAQ1103
PAC2402
COC24
PAC2401
PAQ1101
COQ11
COC26
PAC2602
PAC2601
PAQ1202
FDT3612
PAQ1203
PAR7302 PAR7301
PAT504 PAT503
PAT505 PAT506
COQ12
PAQ1201
PAR7402 PAR7401
COR74
PAC2502
COC25
COR6
PAR602
PAR601
PAR7002
PAR7001
PAU801 PAU808
PAR7202
PAU802
PAU803
PAU807
UCC25600
PAU806
PAR7201
PAU804 PAU805 U8
PAC2501
COR19
PAR1902
COR30 PAR3001
PAR3002
PAR1901
PAU201 PAU208
R20
PAR2002
COR21
PAR2001 PAR2102
COR15 PAR1501
LM393D
PAU203 PAU206
PAR2202
PAU204 PAU205 PAR1502
C16
PAC1601 PAC1602
Q2
PAQ202
COQ2
TL431A
PAQ201 PAQ203
COR18
PAR1802
PAR1801
PAR2201
COR22
PAR1702
PAR1701
PAR2101
COR17
PAC1102
PAC1101
PAL201
PAD301
PAD302
PAQ1301
PAQ1302
PAD2802
43V0
PAD2801 PAD2803
R16
PAR1602 PAR1601
PAQ1303
PAR2902 PAR2901 COR29
PAC1001 560VDC
22N
5217
PAC1002
COC10
PAU108 PAU107 PAU105
PAU101 PAU102 PAU103 PAU104
PAT501
PAT508
PAC801
PAR502
PAR501
PAD202
PAD201
COR224 PAR22402
PAR22401
COR227
COR8
COC242
COC218 PAC21801 PAR22702 PAR801
PAC21802
PAR22701 PAR802
PAC24202
PAC24201
COC204 PAC20401
PAC20402
PAN120501
PAU20508 PAU20507 PAU20506 PAU20505
PAR5502
PAR5501
PAN120401
PAD21301
PAD21303
PAR5601
PAR5602
PAN120601
PAD21302
PAR5801
PAR5802
R203 R219
PAR24002
PAR24001
COR240
PAN120701 PAN120301
PAR5701
PAN120201
PAR26801 PAR26802 COR268
PAC23302
COC233
8K66
PAU20408 PAU20407 PAU20406 PAU20405
PAC23301
PAC802
COL7
PAL701
PAL702
PAC21001
COR255 PAR25501
PAR25502
PAU20501 PAU20502 PAU20503 PAU20504
PAC21002 PAU20401 PAU20402 PAU20403 PAU20404
COR231
PAR23101
PAR23102
COC226
PAC22602
U205
R223
COC217 PAC21702
PAC21701
PAR22301 PAR702 PAR23302
PAR22302 PAR701 PAR23301
PAR23601 PAC22502
PAR23602
PAC22501
COC225 PAC22601 PAR22201
PAR22202
COR7 COR233 COR236
CON1211
PAC22001
COLink4
COC202
PAC20202
COC212
PAC21201 PAC20801
PAN121101
COC208 COC200
PAC20002
PAC22002
PAR20002
COR200
COC220
COR222
PAN121201
COR232
PAR23201
PAR23202
R58
R57
PAN120801 PAN120101
PALink302
COEC2
PALink301
PAR22102
PAR22101
COR221
PAC23401
PAC23402
COC234
PAC20201 PAC21202 PAC20802 PAC20001 PAR20001
PAC20601 PAC20602 COC206
W201
8
2328
PAW20108 PAW20107 PAW20106 PAW20105 PAW20104 PAW20103 PAW20102 PAW20101
1
1
PAEC201 e
COESD2
ESD
PAEC200
PAL202
PAD101
PAU20101 PAU20102 PAU20103 PAU20104
COC209
PAC20901
PAR20102
PAC20902
PAR20301 PAR21902 COR204
PAR20401
PAR20402
PAR20302 PAR21901
PAR20101
PAC901
PAR302 R3
WARNING
PAD102 PAL401 PAL402
PAF601
COF6 F6
PAC3502
5
PAC3501
PAW204 PAW504 PAQ103
PAW203
PAW202
1A25
PAW503
PAW502
PAC3601
PAC3602
PAQ302 PAQ301 PAQ303
5190
COC36
PAQ101
T810
PAXC500
CORTV20
PAR24301
0R02
PAR24302
RT V
CORTV21
R T V
PAW101 PAW201 PAW501
PAQ102
TOP MID W2 PAW405 BOT
CON4
PAU20002 PAU20001 PAC22701
PAC22702
PAR23801
PAR23802
COR238
PAC101
SA115S / SA221S AMP
PAL20000
COXC6
PAXC600
CORTV26
453UH
6699
COIL
COPF1 PAPF100
COEC4
R43 PAR4301 PAR4302
R35 PAR3501 PAR3502
COQ7
PAQ702 PAQ701
MMBTA92
PAQ703
COR44 PAR4402
PAR4401
PAEC401
PAEC400
PAD1202
PAD1201
PAD1402
8V2
PAD1401 PAD1403
PAC2101
PAC2102
PAW300
CON3
PAW301
PAN301
PAW302
PAW303
300
PAW404
PAW403
PAW402
PAW401
PAW400
PAC2901
COC29
PAC2902
PAC3301
PAC3201
PAC3202
COC32
COC33
PAC3302 PAC3402
PAC3401
PAN401
PAD401
PAD402
PAR6701
PAR6702
R71 PAR7101
PAR6501
PAR6502
PAR6601 PAR6401
PAR7801 PAR7702
PAR7102 PAR6602
COD25
PAD2501
C42 R66
PAC4202 PAR5202
PAR6402
PAC3801
PAR7802 PAR7701
R77
PAD2502 PAC4201
PAD2402
PAR5201
PAC3802
PAR7601
PAR7602
PAQ1403
PAQ1402
PAQ1401
PAD2401
PAQ1501
PAQ1502
PAQ1503
S/N LABEL
PAD1602
8V2
PAD1601 PAD1603
COSNL1
PAR5402
PAR5401
PAC4102
PAC4101
PAU20003 PAU20004
PAU508 PAU507 PAU506 PAU505
PAU501 PAU502 PAU503 PAU504
PAC102
PAQ603
MMBTA42
PAQ601 PAQ602
PAC4001 PAC4002
10U
COC39
SA115S/SA221S
M1833 V01
R75
PAEC101
R T V
COXC9
PAXC900
COR256
PAR25601
PAU20601
PAU20603
PAU20605
PAU20604
PAR25602
PAL20002
COC22
PAU403 PAU402 PAU401
ZXGD3002E6
PAU406 PAU404 PAU405
+
PAU20301
PAU20302
PAU20303
PAU20304
PAU20305
PAU20306
PAU20307
PAU203014
PAU203013
PAU203012
PAR23002 DNS
COR9
PAR902
PAU306 PAU305 PAU304 U3
ZXGD3002E6
PAU301 PAU302 PAU303
PAR901
PAU203011
PAU203010
PAU20309
PAU20308
COZD200
COR234
COC221
PAR23702
1R0
PAR23701
COD205
COR25
PAR2501
PAR2502
R237
C224
PAR7902
1U
PAR7901
+
PAR2301 PAR25101 PAR24901 PAD2102
PAR22901
10R
PAR22902
COR225
PAR22501 22R PAR22502
PAL20001
CORTV4
PAR2302 PAR25102 PAR24902
COR23 COR251 COR249
PAD2101
COD21
PAR6102
PAR6101
COC223
PAR6301
619K
PAR6202 PAR6201
PAD2202 DNS
PAC22301
PAC302
PALink201
CORTV18
PALink202
COLink5
PALink502
PALink501
140V
COLink2 PARTV1800
5949
CORTV3
+
PAC21901
CORTV7
PARTV700
V
PAC21902
PAC22801
CORTV8
PARTV800
V
PAC22802
CORTV19 600V
PARTV1900
PAC301
PATJH200
5986
10U
COXC8
CORTV6
PARTV600
V
CORTV5
PARTV500
V
PAXC800
PAC22201
PAC22202
PAC22302
PAC22901
PAR4502
PAQ20301
PAQ20302
PAQ20303
PAQ20501
PAQ20502
PAQ20503
PAC22902
COC23
PAC2301
PAC2302
PAR6001
PAD601
4233
2321
+
PAQ20300
PAC2701
COHS1
COC27
COEC10
PAC2702
PAR5902
PAR2602
COEC7
IKW75N65EH5
4233
2321
PAEC1000
PAEC1001
PAEC701
PAEC700
+
PAQ20500
IKW75N65EH5
PAC401
+
5949
3U3
CORTV10
140V
PARTV1000
PAC402
+
+
CORTV1
PAC1201
PARTV100
V
5923
3300U
PAC1204
PAC1203
CORTV14
PARTV1400
250V
PAC1202
PAC1301
CORTV2
PARTV200
PAC1304
+
PARTV400 PAC1303
5923
3300U
CON7 250V
PAN701
PAC1302
+
CORTV17
+
PAC1504
PARTV1700
PAC1503
5923
3300U
CORTV9
PARTV900
V
250V
PAC1502
CON8
PAN801
+
CORTV16
PAC1403
PAC1401
PAC1404
CORTV11 5923
PARTV1100
3300U
250V
PAC1402
PARTV1600
V
COXC7
COD19
PAD1901 PAD1501 PAD1502
PAD1902 PAR5101 PAR5102
PAXC700
COR40
PAR4002
PAR4001
COR38 PAR3802
PAR3801
PAR6002
COR80
PAR8001
PAR2801
PAR2802
COR28
COR27 PAR2701
PAR2702
PAR8002
PAD1801
PAD1803
PAR5901
PAD1703 PAD1701
8V2
PAD1702
PAD1802
COD18
PAQ1003
MMBTA92 COQ10
PAQ1001 PAQ1002
COD17
PAF502
PAQ801
PAQ802
PAQ803
1A25
COR46 PAR4602
PAR4601
COR48
PAF501
COQ9
PAQ902 PAQ901
PAR5001
COR47 PAR4701
PAR4702
PAR4802
4124
+
PAQ903
PAQ503 PAR3701
MMBTA42
PAQ501 PAQ502 PAR3702
COC18
PAR4801
PAD1102
COD11
PAD1101
PAQ401
PAQ402
COR37
COR41
PAC1802 PAC1801
PAR4102 PAR4101
COHW11
COR39
PAR3902
PAR3901
PAR4201
PAR4202
PAQ403
COC19
COR42
PAR3201 COR32
PAR3202
PAR3601
PAR3602 COR36
6730
IRF830
COEC8
PAR3301
PAR3302
COR33
PAR3101
PAR3102
COR31
PAHS301
PAQ404
PAEC800
PAEC801
PAR4501 PAD602 PAR2601
CLINCH
COCRG1
PACRG100
COCNR1
ORIGIN
M1833 V01 SA115S/SA221S
COPF2
PAPF200
PAPF300
COPF3
Locating Hole
COHW12
4249
+
8832
COTLH3
PATLH300
COCNR2
COCNR3
D
1 2 3 4 5 6 7 8 9 10 11
PCB ASSEMBLY DOCUMENTATION
A
GENERAL ASSEMBLY INSTRUCTIONS
B
1. Bend leads on hand placed parts in direction of pad and cut short to less than length of pad.
No exceptions unless approved by Production Engineering.
2. Any clinch parts with longer leads than the length of the pad must be cut shorter either prior to
wave-soldering or afterwards in PCB finishing. No exceptions unless approved by Production Engineering.
3. After Wave apply RTV to all holes indicated and all larger and between tall capacitors.
C 4. Before tightening screw 8832 on xstr spring 4249 ensure that it is aligned with Q4.
Also silpad 4124 should overhang the edge of the heatsink. See picture below.
12
J
G
H
I
YS#: 8832
DESC: 6-32X1/4 PAN TAPTITE
F
E
MOUNTING HARDWARE INSTRUCTIONS FOR HEAT SPREADER Z1740:
1. First install #8742 screw to align heatspreader Z1740
2. Install all devices, shown in pictures below, on Heat Spreader
TOP VIEW: MOUNTING HARDWARE FOR Q203/Q205:
YS#:8761
DESC: #6-32X1/2"
Q203
YS#: 8800
DESC: #6 KEPS NUT
YS#: 8902
DESC: 4-40X3/4 PAN
Q205
YS#: 8485
DESC: #6 ZINC WASHER
YS#: 4233
DESC: CERAMIC INSULATOR
IMPORTANT!
ADD GOOP ON BOTH SIDES OF CERAMIC INSULATORS
BOTTOM VIEW:
YS#: 4249
DESC: XSTR SPRING
Q4
OVERHANG SILPAD
YS#: 4124
DESC: 1.1x0.82" SIL PAD
YS#: Z1740
DESC: HEAT SPREADER
SEE NOTE 4.
YS#: 8701
DESC: 4-40 KEPS NUT
1st HEATSINK ALIGNMENT SCREW
YS#: 8742
DESC: #4-40X3/8
K
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16
RTV INSTRUCTIONS:
ADD RTV BETWEEN:
C12, C13, C14, AND C15 AFTER WAVE
SOLDER
ADD RTV
17
A
B
Top of Coil L200
13
Ensure that all fastener nubs on tie wraps are well below the top of the coil.
I
J
14
Section:
Product(s):
PCB#:
Assembly Documentation
SA115S/SA221S
M1833 Rev#: V01 EML Rev#: 01
Modified: 2022-01-28
15
File: Assembly.SchDoc
16
Sheet
Tmp Date:
2 Of
17
3
K
C
D
E
F
G
H
J
A
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
B
C
D
E
F
H
I
G
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
7
8
9
10
11
12
13
3
4
1
2
#
.
.
.
.
.
.
.
.
.
.
.
.
.
9
10
11
12
13
6
7
8
3
4
5
1
2
DATE
# DATE
9
10
7
8
11
12
13
3
4
5
6
1
2
.
.
.
.
.
.
.
.
.
.
24-NOV-2020
28-JAN-2022
.
.
.
.
.
.
.
.
.
.
VER#
.
V01
PC#
.
9667
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
Changed C213 YS#7603 680p 5% to YS#9048 680p 1%
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
REF
.
.
.
.
.
.
.
.
.
.
.
.
.
FUNCTION
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
.
POT#
.
.
.
.
.
.
.
.
.
.
.
.
.
STYLE
.
.
.
.
.
.
.
.
.
.
.
.
.
KNOB#
PINOUT DIAGRAMS
CASES AND PINS
1
2
3
4
5
6
7
IRS21844S
IN
SD
VSS
DT
COM
LO
VCC
NC
VB
HO
VS
NC
NC
NC
14
13
12
11
10
9
8
#6686
MC7815
I G O
#7846
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11
14
12 13
15 16 17
A
B
C
D
E
F
G
H
14
Section:
Product(s):
PCB#:
Design Information And History
SA115S/SA221S
M1833 Rev#: V01 EML Rev#: 01 Sheet 3
Modified: 2022-01-28
15
File: History.SchDoc
16
Of
Tmp Rev: V028
17
3
K
J
I
E
F
G
H
I
J
K
1
C
D
A
1
B
2
2
6 W4:7
3 4
CAPACITOR BANK #2
W2:1 3
1
W2:2 3
2
W2:3 3
3
W2
PSGND
SILENT
3 4
-Hi
5
5
6 7 8 9 10 11 12 13 14 15 16 17
A
C1
40X63MM
2700U
5911
250V
C2
40X63MM
2700U
5911
250V
+Hi
C5
40X63MM
2700U
5911
250V
C7
40X63MM
2700U
5911
250V
C9
40X63MM
2700U
5911
250V
PSGND
C6
40X63MM
2700U
5911
250V
C8
40X63MM
2700U
5911
250V
C10
40X63MM
2700U
5911
250V
-Hi
W4
W4:1 6
1
W4:2 6
2
W4:3 6
3
W4:4 6
4
W4:5 6
5
W4:6 6
6
-HiFUSE
F5
3477
+HiFUSE
F6
3477
TO CAPACITOR BANK
PSGND
-Hi
+Hi
SILENT
W5
1
4 W5:1
2
4 W5:2
3
4 W5:3
4
4 W5:4
+Hi
-Hi
PSGND
FROM POWER SUPPLY
2499
F1
T1.25
2499
F2
T1.25
EC2
1
CON_HOLE_189
SILENT
TO METAL DISCHARGE PCB
W1
1
4 W1:1
2
4 W1:2
3
4 W1:3
4
4 W1:4
PSGND
EC3
1
CON_HOLE_189
TH2 TH1
PSGND
EC4
1
CON_HOLE_189
PSGND
PSGND
6 7 8 9 10 11 12
B
C
D
E
F
G
H
I
J
13
Yorkville Sound Ltd.
550 Granite Court
Pickering, ON
Canada L1W 3Y8 www.yorkville.com
14
Product(s): SA115S/SA221S
SA115S/SA221S Description:
PCB#: M1834
Modified: 2020-11-25
15
Rev#: V01
File:
EML Rev#:
M1834.SchDoc
16
02 Sheet 1 Of
Tmp Rev: V032
17
4
K
J
F
G
I
A
B
C
D
E
H
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
4
5
6
1
2
3
9
10
7
8
11
12
13
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
4
5
6
1
2
3
10
11
12
13
7
8
9
#
4
5
6
1
2
3
10
11
12
13
7
8
9
DATE
.
.
.
.
.
.
.
.
.
.
.
.
24-NOV-2020
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
Design Information And History
SA115S/SA221S
PCB#: M1834
Modified: 2020-11-25
Rev#:
File:
V01 EML Rev#:
History.SchDoc
02 Sheet 4 Of
Tmp Rev: V032
15 16 17
4
K
I
7.700
CLINCH
ORIGIN
USE YS# 8691
ALUM SPACER
CHASSIS GND
S/N LABEL
F2
2499
DO NOT DISCONNECT UNTIL BOARD FULLY DISCHARGED
W1
REPLACE FUSE WITH SAME TYPE
F1
2499
TO METAL DISCARGE PCB
C6
HI+
R
T
V
5911
2700U
250V
C10
TEST e
ESD
5911
2700U
250V
HI-
300
FROM SMPS
W5 5911
2700U
250V C9
BREAK
OUT
Into Wave
C8
CAUTION DISCHARGE
BEFORE SERVICING
C2
USE YS# 8691
ALUM SPACER
CHASSIS GND
5911
2700U
250V
5911
2700U
250V
C 2020
W2
C5
5911
2700U
250V
CAUTION DISCHARGE
BEFORE SERVICING
M1834 V01
C1
F6
3477
C7
5911
2700U
250V
3477
3477
300
TO POWER AMP
W4
300
HI+
HI+
HI-
HI-
5911
2700U
250V
F5
3477
3 OZ COPPER
SA115S/SA221S
USE YS# 8691
ALUM SPACER
CHASSIS GND
TO POWER AMP
TEST
E
F
G
H
I
J
K
1
D
C
A
B
1 2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13
1. When inserting fuse holders YS#3477, orient them such that the side with the rings match
with the rings on the silkscreen as shown in photo #1.
2. RTV all along sides in between all capacitors as shown in photo #2
14 15 16 17
A
B
C
D
2 3
#1
4 5 6 7 8 9
#2
10 11 12 13
J
14
Section:
Product(s):
PCB#:
Assembly Documentation
M1834
SA115S/SA221S
Rev#: V01 EML Rev#: 02
Modified: 2021-04-15 File: Assembly.SchDoc
15 16
Sheet 2 Of
Tmp Rev: V032
17
4
K
I
E
F
G
H
J
F
I
A
B
C
D
E
G
H
1 2 3 4 5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
6
7
8
4
5
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
7
8
5
6
11
12
13
3
4
1
2
#
5
6
7
8
9
10
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
DATE
.
.
24-NOV-2020
21-JAN-2020
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
ADDED FUSE HOLDER INSTRUCTIONS TO ASSEMBLY
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
PCB#:
Design Information And History
M1834
SA115S/SA221S
Rev#: V01
Modified: 2021-04-15 File:
EML Rev#:
History.SchDoc
02 Sheet 4 Of
Tmp Rev: V032
15 16 17
4
K
I
AC Line Current Sense
ACBLK2 To AC IN Connector
Pin 1 BLK
W13:2
2
2 PIN
2 a
W13:1
2
W13
2 PIN
1
From AC Switch
Pin 1 BLK
ACBLK1 a
2 W2:1
.
R74
1K8
To DSP PCB
2 W2:2
T1
a
CRITICAL SAFETY COMPONENTS
THIS SYMBOL IS PLACED ADJACENT TO
SAFETY CRITICAL COMPONENTS.
W10:1 4
1
To Cap Boards
1
4 W11:1
1
4 W12:1
W10:2 4
2
W10:3 4
3
W10:4 4
4
2
4 W11:2
3
4 W11:3
4
4 W11:4
2
4 W12:2
3
4 W12:3
4
4 W12:4
CON_HOLE_156
1
HC1
Section:
Product(s):
Synergy Current Sense
Synergy
PCB#: M1837
2021-04-15
Rev#:
File:
V01 EML Rev#:
M1837.SchDoc
01 Sheet 1 Of 4
J
A
B
C
D
E
F
H
I
G
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
6
7
8
3
4
5
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
7
8
9
10
11
12
13
3
4
1
2
#
9
10
7
8
11
12
13
3
4
5
6
1
2
DATE
.
.
.
.
.
.
.
.
.
.
.
.
19-APR-2021
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
14
Section:
Product(s):
PCB#:
Design Information And History
Synergy
M1837 Rev#: V01 EML Rev#: 01 Sheet 4
Modified: 2021-04-15
15
File: History.SchDoc
16
Tmp Rev: .
17
Of 4
K
J
I
R74
Synergy
M1837 V01
TO DSP
C
2020
T1
AC BLK
W13
4263
0 30
W10
HI-
W11
0 30
GND
HI+
DISCHRG
AC CURRENT SENSE
S/N LABEL
W12
0 30
E
F
G
H
I
J
K
1
D
C
A
B
1 2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
Transformer T1 Assembly
1) Bend shielded wire as shown in picture 1.
2) Route cable through transformer YS#1233 as shown in pictures 2 and 3.
3) Place transformer on board, and bend cable once more as shown in pictures 4 and 5.
4) Line up cable connections to indicator on board as shown in picture 5.
13 14 15 16 17
A
B
C
D
2
#1
#4
3 4 5
#2
6
#5
7 8
#3
9 10 11 12 13
J
14
Section:
Product(s):
Assembly Documentation
Synergy
PCB#: M1837
Modified: 2021-04-15
Rev#:
File:
V01 EML Rev#:
Assembly.SchDoc
01
15 16
Sheet 2
Tmp Rev: .
Of
17
4
K
I
E
F
G
H
J
F
I
A
B
C
D
E
G
H
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
6
7
8
4
5
1
2
3
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
7
8
5
6
11
12
13
3
4
1
2
#
5
6
7
8
9
10
11
12
13
3
4
1
2
DATE
.
.
.
.
.
.
.
.
.
.
.
.
19-APR-2021
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
PCB#:
Design Information And History
Synergy
M1837 Rev#: V01 EML Rev#: 01 Sheet 4
Modified: 2021-04-15 File: History.SchDoc
Tmp Rev: .
15 16 17
Of 4
K
I
D
E
F
G
H
I
J
K
1
B
C
A
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B
2
SILENT
CAPACITOR BANK #2
W2:1 3
1
W2:2 3
2
W2:3 3
3
W2
W4
PSGND
-Hi
+Hi
W4:1 6
1
W4:2 6
2
W4:3 6
3
W4:4 6
4
W4:5 6
5
W4:6 6
6
PSGND
6 W4:7
CAPACITOR BANK
-Hi
C5
40X63MM
2700U
5911
250V
C7
40X63MM
2700U
5911
250V
C9
40X63MM
2700U
5911
250V
C1
40X63MM
2700U
5911
250V
C3
40X63MM
2700U
5911
250V
PSGND
C6
40X63MM
2700U
5911
250V
C8
40X63MM
2700U
5911
250V
C10
40X63MM
2700U
5911
250V
C2
40X63MM
2700U
5911
250V
C4
40X63MM
2700U
5911
250V
+Hi
+Hi
-Hi
2499
F1
T1.25
SILENT
TO METAL DISCHARGE PCB
W1
1
4 W1:1
2
4 W1:2
3
4 W1:3
4
4 W1:4
2499
F2
T1.25
-Hi
SILENT
+Hi
W5
1
4 W5:1
2
4 W5:2
3
4 W5:3
4
4 W5:4
PSGND
FROM POWER SUPPLY
EC2
1
CON_HOLE_189
PSGND
EC3
1
CON_HOLE_189
PSGND
EC4
1
CON_HOLE_189
PSGND
PSGND
TH2 TH1
3 4 5 6 7 8 9 10 11 12
C
D
E
F
G
H
J
13
Yorkville Sound Ltd.
550 Granite Court
Pickering, ON
Canada L1W 3Y8 www.yorkville.com
14
Product(s):
Description:
PCB#:
Modified:
M1840
SA315S/SA221S
SA315S
2020-03-19
15
Rev#: V01
File:
EML Rev#:
M1840.SchDoc
16
02 Sheet 1 Of
Tmp Rev: V032
17
4
K
I
J
F
I
A
B
C
D
E
G
H
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
7
8
5
6
9
10
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
7
8
5
6
11
12
13
3
4
1
2
#
9
10
7
8
5
6
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
DATE
.
.
.
19-MAR-2020
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
MJL21194 (YS#6988)
MJE15032 (YS#6808)
TO-220
E C B
TO3P
E C B
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
Design Information And History
SA315S/SA221S
PCB#: M1840
Modified: 2020-03-19
Rev#:
File:
V01 EML Rev#:
History.SchDoc
02 Sheet 4 Of
Tmp Rev: V032
15 16 17
4
K
I
7.700
Score
USE YS# 8691
ALUM SPACER
CHASSIS GND
S/N LABEL
F2
2499
DO NOT DISCONNECT UNTIL BOARD FULLY DISCHARGED
W1
REPLACE FUSE WITH SAME TYPE
F1
2499
TO METAL DISCARGE PCB
C6
HI+
R
T
V
5911
2700U
250V
C10
TEST e
ESD
5911
2700U
250V
HI-
W5
300
FROM SMPS
5911
2700U
250V C9
Score
CLINCH
ORIGIN
79mil(2mm) Rad ~ 4 PLACES
BREAK
OUT
Into Wave
C8
CAUTION DISCHARGE
BEFORE SERVICING
C2
USE YS# 8691
ALUM SPACER
CHASSIS GND
5911
2700U
250V
5911
2700U
250V
C 2019
W2
C5
5911
2700U
250V
CAUTION DISCHARGE
BEFORE SERVICING
M1840 V01
C1
C7
5911
2700U
250V
5911
2700U
250V
5911
2700U
250V
5911
2700U
250V
T V
C4
300
TO POWER AMP
W4
0 30
HI+
HI+
HI-
HI-
TO POWER AMP
C3
SA315S/SA221S
M1840 V01
SA315S/SA221S
USE YS# 8691
ALUM SPACER
CHASSIS GND
TEST
D
E
F
G
H
I
J
K
1
C
A
B
1 2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13
1. RTV ALL LARGE AND TALL CAPS AND RTV HOLES PROVIDED.
14 15 16 17
A
B
C
2 3 4 5 6 7 8 9 10 11 12 13
J
14
Section:
Product(s):
Assembly Documentation
SA315S/SA221S
PCB#: M1840
Modified: 2020-03-19
Rev#:
File:
V01 EML Rev#:
Assembly.SchDoc
02
15 16
Sheet 2 Of
Tmp Rev: V032
17
4
K
H
I
D
E
F
G
J
F
I
A
B
C
D
E
G
H
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
7
8
5
6
9
10
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
7
8
5
6
11
12
13
3
4
1
2
#
9
10
7
8
5
6
11
12
13
3
4
1
2
.
.
.
.
.
.
.
.
.
DATE
.
.
.
19-MAR-2020
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
VER#
.
.
.
.
.
.
.
.
.
.
.
.
V01
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASED FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
.
.
.
.
.
.
.
.
.
.
.
.
REF
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE KNOB#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PINOUT DIAGRAMS
MJL21194 (YS#6988)
MJE15032 (YS#6808)
TO-220
E C B
TO3P
E C B
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15 16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
Design Information And History
SA315S/SA221S
PCB#: M1840
Modified: 2020-03-19
Rev#:
File:
V01 EML Rev#:
History.SchDoc
02 Sheet 4 Of
Tmp Rev: V032
15 16 17
4
K
I
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
H
I
G
+15VIP+
B
D2
D1005
CDSF4148
F
C
D
E
W1:4 4
4
W1:3 4
3
N10
W1:2 4
2
W1:1 4
1
N2
N11
N12
R181
W125
31K6
0805
GNDA
R165
W125
31K6
0805
+15VIP+
GNDA
C33
0603
R59
187K
0805
GNDA
6
-
5
+
TL072
7669
7
D40
CDSF4148
D1005
R5
W125
22K1
0805
R107
22K1
0805
W125
6 -
R12
W125
10K00
0805
TL072
7669
7
5
+
R6
10K00
0805
U8:2
SO8
D3
D1005
CDSF4148
C37
0603
2
3
-
+
TL072
7669
1
VSS
U7:1 SO8
D39
CDSF4148
D1005
FROM JACK BOARD
GNDA
R58
187K
0805
TO CHASSIS
CON_HOLE_156
GROUND
1
HC2
GNDA
SIGHP
CHSGND1
C49
16V 10U
1206
C50
16V 10U
1206
R37
W100
6K98
0805
C52
0805
R75
10K00
0805
GNDHP
+15VIP
5
+
7
6
-
7817
MC33078
R32
W125
10K00
0805
C51
100P
0805
50V
R76
6K98
0805
VSS
HP OUTPUT TO SA315S
R28
W125
47R5
0805
R57
2K0
0805
K1:2
3700
RELAY 2C
R55
560R
0805
R56
200R
0805
R30
W100
2K32
0805
R49
750R
0805
R50
DNS
0805
R31
W125
10R0
0805
VSS
C48
10U
1206
16V
3
+ U1:1
1
2
-
7817
MC33078
GNDAMP RELAY 2C
3700
K1:1
R39
W125
47R5
0805
J
K
1
50V
100N
C15
0805
GNDAMP 50V
100N
C20
0805
2
GNDAMP
8
V+
MC33078
7817
4
V-
SO8
U1:3
-15VIP
3 4
GNDHP
R62
W125
4K02
0805
5
C40
100P
0805
50V
R65
W125
4K02
0805
6
CHECK RESISTOR VALUES WITH TOM
+15VIP
R21
W100
100R
0805
+15VIP+
50V
C13
0805
100N
50V
C14
0805
100N
8
V+
TL072
7669
8
V+
TL072
7669
U7:3 U8:3
4
V-
SO8
4
V-
SO8
GNDA 50V
C19
0805
100N
R38
W100
100R
0805
-15VIP
R4
W125
37K4
0805
2
-
TL072
7669
1
3
+
SO8
U8:1
GNDAMP
R42
W125
10R0
0805
7
R48
W125
750R
0805
ANALOG GND
VSS
N18
1
3 W6:1
N17
2
3 W6:2
3
N16
3 W6:3
GNDHP
8
R52
W125
560R
0805
C17
10U 16V
1206
R13
200R
0805
VSS
VSS
+15VIP
R18
W100
100R
0805
-15VIP
R33
W100
100R
0805
DSP.SchDoc
CHSGND1
CHSGND1
GNDAMP
INPUT1
INPUT2
VSS
GNDHP GNDA CHSGND
DSP SHEET
+15V
1
XC19
CON_HOLE_156
GNDA
-15V
+15VW4
D11
CDSF4148
D1005
+15VW2
D10
CDSF4148
D1005
TH1
+15V
L2
7967
9
L12
-15VW4
D7
-15VW2
CDSF4148
D1005
D12
CDSF4148
D1005
10
RIBBON_GND
7967
-15V
L10
7967
8
V+
V-
4
TL072
7669
U9:3
SO8
11
50V
C31
0805
100N
50V
C5
0805
100N
GNDAMP
OUTPUT2
OUTPUT1
LEDSOFF
W2-PIN2
FROM POWER SUPPLY
MUST BE PLACED
ON INPUT PCB
NEAR RIBBON
+15VIP
50V
100N
C38
0805
ZD1
18V0
SOD-323
50V
100N
SPACER GROUND
HERE
C39
0805
ZD2
18V0
SOD-323
-15VIP
GNDA
12
C9
63V
330N
RAD .2in
LED
13
C10
63V
330N
RAD .2in
R23
47K
0805
CODEC B OUTPUT
FOR TEST PURPOSE
5
6
+
-
TL072
7669
7
U9:2
SO8
TP15
R22
47K
0805
GNDAMP
GNDAMP
R16
W100
2K0
0805
R17
W100
2K0
0805
W4
13in 8C-26AWG
RIB 1 W/LCK
W4:5 8
5
W4:4 8
4
W4:3 8
3
W4:2 8
2
W4:1 8
1
3
+
2
-
TO POWER
AMP PCB
R53
W100
2K0
0805
TL072
7669
1
U9:1
SO8
R73
W100
2K0
0805
R54
W125
4K02
0805
R47
W125
4K02
0805
Use W2 for single Amplifier Testing
W2
13in 8C-26AWG
RIB 1 W/LCK
-15VW4
W4:8 8
8
+15VW4
W4:7 8
7
W4:6 8
6 SIGNAL
-15VW2
+15VW2 N13
8
8 W2:8
7
8 W2:7
N3
6
8 W2:6
N6
N5
5
8 W2:5
4
8 W2:4
N7
3
8 W2:3
N8
2
8 W2:2
N9
1
8 W2:1
TO POWER
AMP PCB
SIGHP
SIGNAL TO
AMP INPUT
R51
W125
47R
0805
N4
C2
0603
R40
W125
0R0
0805
GNDAMP
RIBBON_GND
A
B
C
D
E
F
G
H
I
J
*
*
*
* www.yorkville.com
14
Product(s): SA115S/SA221S
POWERED SUBWOOFER INPUT PCB Description:
PCB#: M1950
Modified: 2021-03-03
15
Rev#: V01
File: INPUT.SchDoc
EML Rev#:
16
V01 Sheet 1 Of
Tmp Rev: V031
17
3
K
F
G
I
J
A
B
C
D
E
H
K
1
+15V
2
-15V
GNDA
CHSGND1
CHSGND1
3
W2-PIN2
+3V3
R25
W125
10K00
0805
R44
W125
4K7
0805
R26
W125
10K00
0805
4
50V
C135
0805
100N
+VPS
5 6 7 8
POWER LED
ACTIVE
LD1
GRN
.
7031
R36
249R0
0805
LD6
GRN
.
7031
R35
249R0
0805
9
CLIP
LD3
RED
.
7033
R7
499R
0805
10
TLIM
LD4
YEL
.
7032
R9
499R
0805
XLIM
LD2
YEL
.
7032
R27
499R
0805
11
DGGND
12 13 14 15
5
6
7
S4 AVERAGE POWER SELECT
FX Select
4POS
4189
8
C2
4
3
2
1
C1
DGGND
16 17
A
+15V
GNDA
-15V
LEDSOFF
LED
D4
DO214AC
B160
R29
4K7
0805
R8
W125
750R
0805
1
+3V3
50V
C1
0805
100N
DGGND
VREFL
+3V3
50V
C23
0805
100N
1U
C24
1206
25V
DGGND
RAIL SENSE
R176
W125
FROM MAIN SUPPLY
3K32
0805
R10
1K5
0805
50V
C134
0805
100N
VREFL
R14
W125
750R
0805
R1
750R
0805
50V
C47
0805
100N
DGGND
25V
C46
1206
1U
+3V3
10V
10U
C18
0805
+3V3POT
50V
C29
0805
100N
ADC1_MP/DP
TP9
TP10
ANALOG TP'S
9
10
11
7
8
12
13
14
15
3
4
5
1
2
6
16
17
18
19
20
PTE0/UART1_TX
PTE1UART1_RX
PTE2
PTE3
PTE4
PTE5
VDD
VSS
PTE16/UART2_TX
PTE17/UART2_RX
PTE18/ADC0_SE6a
PTE19/ADC0_SE6a
ADC1_DP3
ADC1_DM3
ADC1_DP0/
ADC1_DM0/
VDDA
VREFH
VREFL
VSSA
U4
MK10DN512VLK10
6667
LQFP-80
VDD
60
59
VSS
PTC3
58
PTC2
57
PTC1 56
PTC0 55
PTB19
54
PTB18
53
PTB17
52
PTB16
51
VDD
50
VSS
49
PTB11
48
PTB10
PTB3
47
46
ADC0_SE12 45
ADC0_SE9 44
ADC0_SE8 43
RESET_b
42
PTA19
41
+3V3
50V
C21
100N
0805
1U
C22
1206
25V
DGGND
+3V3
1U
C27
1206
25V
50V
C28
0805
100N
DGGND
R66
W125
10K00
0805
MMBT5401
7837
Q1
CHSGND1
+3V3
R41
37K4
0805
C3
25V 1U
1206
R72
37K4
0805
AC CURRENT SENSE
R71
33R
0805
R45
33R
0805
R46
33R
0805
N15
2 W8:1
N14
2 W8:2
DGGND
R69
W125
47K
0805
DOWN SA315S+SA221S
GND
3522
S1:1
3522
S1:2
GND
+15V
B
C
D
E
Q2
MMBT5401
+15V
GND
C55
ELE 8mm
L11
7967
R15
0R27
1206
R3
1K21
0805
R2
W100
3K74
0805
GND
+3V3
GND
R11
W100
499R
0805
PUT BESIDE EACH OTHER
1
8200NH L6
2
+15SUPPLY
8
7
5
+5V SUPPLY
FOR U1 DSP
VCC
U2
MC33063A
SO8
SW_C 1
DRV_C
ISEN SW_E 2
TCAP
3
INV
GND
7719
STEP DOWN
CONVERTER
470P
C32
0603
50V
D1
DO214AC
B160-13-F
GNDA GND
+3V3POT
L3
220UH
8152
GND
C6
RAD
6V3
470U
+5V
DGGND
NET TIE
VREFL
+3V3CD
TP1
TP12 +3V3
DGGND
TP7
+5V
TP8
VOLTAGE
TEST POINTS
TP13
GND
TP14
IN
U5
LP2950-33
OUT
TO92
7012
VSS
+3V3
50V
C4
0805
100N
VREFL C43
20P
0805
100V
DGGND
C44
20P
0805
100V
DGGND
+3V3
R177
100K
0805
PROGRAM
HEADER
1
W3:1
10
3
W3:3
10
5
W3:5
10
7
W3:7
10
9
W3:9
10
2
W3:2
10
4
W3:4
6
W3:6
10
8
W3:8
10
W3:10
N1
SWD_DIO
SWD_CLK
RESET
DGGND
C16
63V
100N
RAD .2in
1
8200NH
2
L7
W5
SWO
GND
CLK
RST
DIO
VCC
Program
2
1
4
3
6
5
SWD_CLK
SWD_DIO
RESET
+3V3
+3V3
DGGND
C11
63V
100N
RAD .2in
TO92
IN
U6
LP2950-33
OUT
7012
+3V3CD
C42
63V
100N
RAD .2in
50V
C12
100N
0805
C8
10U
63V
RAD .2in
DGGND
2 3 4
DGGND
5 6 7
VSS
8 9
+3V3
R178
W125
1K02
0805
R20
47R
0805
50V
C25
100N
0805
1U
C26
1206
25V
C45
0805
DGGND
+3V3POT
DGGND
GAIN
C41
63V
100N
RAD .2in
50V
C30
100N
0805
D
P4:1
B
10K
.
2339
D
P4:2
B
10K
.
2339
R70
47K
0805
D5
SOD-323
18V0
R67
10K00
0805
Q3
MMBTA42
D6
D1005
CDSF4148
R68
698R
0805
F
G
VSS
+3V3
1U
25V
1206
C35
CODEC
DGGND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
U3
VCOC
PS AK4558
ROUT
28
LOUT 27
CKS3
CKS2
CKS1
6670
CKS0/TDMI
LRCK
SDTO
BICK
SDTI
MCKI
TVDD
VSS2
VDD18
QFN28
VCOM 26
VSS1
25
AVDD
24
RIN
23
LIN
22
LDOE
21
LOPS
PMDAR/CAD1
PMDAL/CAD0
PMADR/SDA
PMADL/SCL
PDN
20
19
18
17
16
15
GROUND GNDA
NODES ON
POWER AMP
R24
10K00
0805
ALUMINUM
SPACER
TO CHASSIS
OUTPUT2
25V
1U
1206
C36
INPUT1
VSS
OUTPUT1
INPUT2
VREFL GNDA
VSS
C7
RAD .2in
10U
63V
50V
C34
0805
100N
+3V3CD
P4:3
B
.
10K
2339
D
VSS
DGGND VSS
VSS
10 11 12
GND
13
VSS
14
-15V
H
I
J
Section:
Product(s):
DSP
SA115S/SA221S
PCB#: M1950
Modified: 2021-03-03
Rev#:
File:
V01
DSP.SchDoc
EML Rev#:
15 16
V01 Sheet 2 Of
Tmp Rev: V031
17
3
K
J
F
G
I
A
B
C
D
E
H
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
4
5
6
1
2
3
9
10
7
8
11
12
13
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
4
5
6
1
2
3
10
11
12
13
7
8
9
# DATE
4
5
6
1
2
3
10
11
12
13
7
8
9
.
.
.
.
.
.
.
.
.
.
26-NOV-2020
VER#
.
V01
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASE FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
REF
.
.
.
.
.
.
.
.
.
.
S1
S4
P4
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION POT/SW YS# STYLE
.
.
.
.
.
.
.
.
.
.
MODE SELECT
HF ROLL OFF
GAIN
.
.
.
.
.
.
.
.
.
.
4202
4202
2339
.
.
.
.
.
.
.
.
.
.
ROT
ROT
P34
KNOB#
.
.
.
.
.
.
.
.
.
.
8653C
8653C
8653C
PINOUT DIAGRAMS
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15
"STYLE_P32"
16 17
A
B
C
D
E
F
G
H
J
14
Section:
Product(s):
Design Information And History
SA115S/SA221S
PCB#: M1950
Modified: 2021-03-03
Rev#:
File:
V01 EML Rev#:
History.SchDoc
V01 Sheet 3 Of
Tmp Rev: V031
15 16 17
3
K
I
U4 PROGRAM HEADER
W3
9 1
R
4
6
R
7
1 4183
10 2
C4
BOTTOM ENTRY
PROGRAM PORT
+5V
= GROUNDS MERGE
+3V3
C3
4189
100N
VSS C32
470P
B160-13-F
TP12
LP2950-33
FX Select
U5
100N
C16
LP2950-33
U6
100N
0R27
R15
C46
C27
C22
C21
1U 1U
100N
C28 100N
70
S4
C30
C
2
5
40
30
C26
1U
100N
20P
C45
47R
49R9
R19
10U
100N
3522
+
750R
2K32
37K4
4148
22K1
10K00
R26
D4
GRN
GRN
LD1
R14
R8
C1
3K32
R1
C23 100N
1U
C24
R29
100N
10U
100N
8200NH
TP9
499R R11
1
2339
10U
R56
200R
100K
10K00
R24
10U
C17
200R
560R
P4
560R
DNS
750R
10K00
R12 R107
10K0
22K1
C33
470P
C19
100N 100N
R17
2K0
47K
R23
100R
R38
C13
R21
100R
4148
D40
D2
100N
R59
C14
CHSGND
C31 100N
R40
C38
R22
R16
0R0
R51
47K
C50
2K0
R53
2K0
4K02
R54
47R
100R
R18
100R
100N
R33 C5
C20
C51
R37
100P
6K98
R32
C15
10K00
- SIG
+ SIG
R75
C
5
2
3 2369
R42
10R0 10R0
1
1
D10
4148
4148
D12
L2
15UH
C39
15UH
L12 15UH
4148
4148
D7
S/N
LABEL
.
GRN
GRN
LD6
499R
R7
LD3
RED
RED
CLIP
SYNERGY INPUT PCB
499R
R9
LD4
YEL
YEL
R27
499R
LD2
YEL
YEL
4K02
100P
Q1
C40
7837
R62
4K02
D6
4148
Q3
MMBTA42
7837
R68
698R
18V0
10K00
R66
47K
R70
10K00
R67
D
E
15 16
A
1 2 3 4 5 6 7 8 9 10 11 12
PCB ASSEMBLY DOCUMENTATION
13
B
C
SPECIAL PRODUCTION NOTES
1.AFTER WAVE USE PIZZA CUTTER TO SEPARATE THE BOARDS.
2.IF REQUIRED USE A JIG FOR INPUT JACK/POT/SWITCH ALIGNMENT.
PCB HARDWARE
SCREWS AND BOLTS NUTS
14
STANDOFFS MISCELLANEOUS
17
A
B
C
D
E
F
G
H
I
J
K
THIS SHEET CONTAINS SPECIAL PRODUCTION NOTES AND A LIST OF PCB HARDWARE PARTS REQUIRED FOR THE BUILD.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Section:
Product(s):
PCB#:
Assembly Documentation
SA115S/SA221S
M1950 Rev#: V01 EML Rev#: V01
Modified: 2021-03-03
15
File: Assembly.SchDoc
16
Sheet 2 Of
Tmp Rev: V031
17
3
K
J
I
F
G
H
J
A
B
C
D
E
F
H
I
G
1 2 3 4
CHANGE HISTORY
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
9
10
11
12
13
6
7
8
3
4
5
1
2
.
.
.
.
.
.
.
.
.
.
.
.
.
DATE #
5
6
7
8
9
10
11
12
13
3
4
1
2
# DATE
9
10
7
8
11
12
13
3
4
5
6
1
2
.
.
.
.
.
.
.
.
.
.
26-NOV-2020
.
.
.
.
.
.
.
.
.
VER#
.
V01
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
PC#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
.
.
.
.
.
.
.
.
.
.
.
.
.
VER#
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
RELEASE FOR PRODUCTION
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
.
.
.
.
.
.
.
.
.
.
.
.
.
DESCRIPTION OF CHANGE
5 6 7 8 9 10 11 12
DESIGN HISTORY AND INFORMATION
13
POTENTIOMETERS AND KNOBS
REF
.
.
.
.
.
.
.
.
.
S1
S4
.
P4
.
.
.
.
.
.
.
.
.
POTENTIOMETERS/SWITCHES AND KNOBS
FUNCTION
MODE SELECT
HF ROLL OFF
.
GAIN
POT/SW YS#
.
.
.
.
.
.
.
.
.
4202
4202
.
2339
STYLE
.
.
.
.
.
.
.
.
.
ROT
ROT
.
P34
KNOB#
.
.
.
.
.
.
.
.
.
8653C
8653C
.
8653C
PINOUT DIAGRAMS
14
K
THIS SHEET CONTAINS A CHANGE HISTORY LOG, A LIST OF THE POTS & KNOBS AND A LEADS & PINS REFERENCE SECTION.
1 2 3 4 5 6 7 8 9 10 11 12 13
15
"STYLE_P32"
16 17
A
B
C
D
E
F
G
H
14
Section:
Product(s):
PCB#:
Design Information And History
SA115S/SA221S
M1950 Rev#: V01 EML Rev#: V01 Sheet 3
Modified: 2021-03-03
15
File: History.SchDoc
16
Of
Tmp Rev: V031
17
3
K
J
I
1. Power Switch & Indicator
The green power LED indicates when the power turned On. When power is turned off or not available, the indicator will blink as the power supply discharges. The circuitry will not reboot unless the power supply is fully discharged before being turned back on. Turning the power back on before the power supply is discharged will simply resume normal operation.
2. PowerCON TRUE AC Loop Thru
As a standard, the AC inlet on the SA221S accepts locking PowerCON
TRUE power cords. There is also an AC outlet that can be used to loop power through to other cabinets in your array using a male to female
PowerCON TRUE looping power cord. Check with your local Yorkville dealer for availability of these accessory cords.
IMPORTANT: DO NOT EXCEED THE CURRENT RATING OF THE
POWER and ACCESSORY CORDS. PLEASE READ THE SECTION
OF THE OWNER’S MANUAL CALLED CASCADE INSTALLATION
3. Input Jack
This female-XLR accepts line level XLR cables. For best noise reduction use balanced sources.
4. Dual Link Outputs
These XLR connectors can be used with standard XLR cables to daisychain up to 20 SA221S or SA315 cabinets without signal degradation.
Simply loop from one cabinet’s Link jack to the next cabinets Input jack. In many cases this limit of 20 cabinets can be exceeded, consult
Yorkville Sound for more details.
5. SA221S Level
This control adjusts the volume level of the SA221S relative to the input signal level and is used to fine tune the cabinet’s volume relative to the mixer settings. It is perfectly acceptable to set the SA221S Level above or below the center 0 dB setting.
6. Clip, X-Max, VC-Therm, Activity Indicators
The Clip and Limit LED indicators illuminate to guide the user to proper operating levels.
Illumination of either yellow Limit LEDs indicate a level has been reached where the limiters are reducing the signal internally to prevent damage or distortion. It also indicates that further increases in input level, or increasing the SA221S
Level control position will not appreciably increase output.
The red Clip LED indicates that the input level is excessive and further increases in level will cause severe distortion. The input signal should be reduced at the source until Clip activity ceases.
7. Average Power Limit
The SA221S can operate on 15 amp 120VAC power sources or 20 amp 120 VAC power sources. The SA221SCE can operates on 16 amp 230VAC power source. Safety regulations limit the power draw on these circuits to 80% of 20, 16 or 15 amps. The SA221 operates within these limitations. The stock product limits the current to 12 amps and when modified by a qualified technician using the SA221KIT will increase the limit current to 16 amps. Operation when set to 16 amps requires the appropriate power cord and 20 amp power source.
The average power limit control allows the power to be reduced to allow operation on limited power availability. Full power transients will be allowed through but if the average power is excessive then the power will be limited. In the 16 amp (8 amp CE) position the average power is limited only by the voice coil temperature. In the
12 amp (6 amp CE) position with most music, the limiter will be only active occasionally depending on the music content. In the 8 amp (4 amp CE) position certain types of music will not be limited, primarily music without deep bass or where the bass is unprocessed. The 6 amp (3 amp CE) position will significantly reduce the output when the music content has continuous bass content below 45 Hz. The green power on indicator will dim to indicate when the line current limiter is active.
8. 50 Hz High-Pass Output
The SA221S provides a line level 50 Hz high-pass XLR output intended to provide the correct equalization, crossover and time alignment to use SA315S subwoofers along with SA221S subwoofers. This output is not suitable for any other usage. This output should not be routed to the full range cabinets.
Normally this would be used with the 50 Hz lowpass switch depressed.
9. 100 Hz / 50 Hz Lowpass Switch
This switch allows the SA221S subwoofers to be used with SA315S subwoofers. Combined with the 50 Hz High-pass output this will ensure correct crossover and time alignment.
To get the full Owner’s Manual please visit our website at http://www.yorkville.com/manuals/ or, if you need a printed version call 905-837-8777
Printed In CANADA
QuickStart-SA221S-00-1v2 • YS#QSTART-SA221S • January 24, 2022
1. Interrupteur et Indicateur d’Alimentation
Le voyant d’alimentation vert indique que l’appareil est sous tension. Lorsque l’alimentation est coupée ou non disponible, le voyant clignote pendant que l’alimentation se décharge. Le circuit ne redémarre pas si l’alimentation n’est pas complètement déchargée avant d’être remise sous tension.
Si vous remettez l’appareil sous tension avant que l’alimentation ne soit déchargée, le fonctionnement normal reprendra simplement.
2. Boucle CA PowerCON TRUE
En standard, l’entrée CA du SA221S est compatible avec les cordons d’alimentation PowerCON TRUE à verrouillage. Il y a également une prise CA qui peut être utilisée pour alimenter en boucle d’autres enceintes de votre réseau en utilisant un cordon d’alimentation PowerCON
TRUE mâle à femelle. Vérifiez auprès de votre revendeur Yorkville local pour vérifier la disponibilité de ces cordons accessoires.
IMPORTANT: NE PAS DÉPASSER LE COURANT
MAXIMAL DES CORDONS D’ALIMENTATION ET
D’ACCESSOIRES. VEUILLEZ LIRE LA SECTION DE CE
MANUEL INTITULÉE “INSTALLATION EN CASCADE.”
3. Prise d’Entrée
Cette prise femelle-XLR est compatible avec les câbles de microphone
XLR de niveau ligne. Pour une meilleure réduction du bruit, utilisez des sources équilibrées.
4. Sorties Dual Link
Ces connecteurs mâles XLR peuvent être utilisés avec un câble XLR standard pour relier en chaîne jusqu’à 20 enceintes SA221S ou SA315 sans dégradation du signal. Il suffit de faire une boucle entre la prise
Link d’une enceinte et la prise Input de l’enceinte suivante. Dans de nombreux cas, cette limite de 20 enceintes peut être dépassée, consultez Yorkville Sound pour plus de détails.
5. Commande de Niveau SA221S
Cette commande permet de régler le niveau de volume du SA221S par rapport au niveau du signal d’entrée et est utilisée pour affiner le volume du caisson par rapport aux réglages du mélangeur. Il est parfaitement acceptable de régler le niveau du SA221S au-dessus ou au-dessous du réglage central de 0 dB.
6. Indicateurs d’Activité Clip, X-Max, VC-Therm
Les indicateurs DEL Clip et Limit s’allument pour guider l’utilisateur vers les niveaux de fonctionnement appropriés.
L’illumination de l’une ou l’autre des DEL jaunes de limite indique qu’un niveau a été atteint où les limiteurs du SA221S réduisent le signal de façon interne pour éviter tout dommage ou distorsion. Il indique également que d’autres augmentations du niveau d’entrée ou de la position de la commande de niveau du
SA221S n’augmenteront pas sensiblement la sortie acoustique.
La DEL Clip rouge indique que le niveau d’entrée est excessif et que toute augmentation supplémentaire du niveau entraînera une distorsion grave. Le signal d’entrée doit être réduit à la source jusqu’à ce que l’activité d’écrêtage cesse.
7. Limite de la Puissance Moyenne
Le SA221S peut fonctionner avec des sources d’alimentation de 15 ampères 120VAC ou de 20 ampères 120 VAC. Le SA221SCE peut fonctionner sur une source d’alimentation de 16 ampères 230VAC. Les règles de sécurité limitent la puissance consommée sur ces circuits à 80% de 20, 16 ou 15 ampères. Le SA221 fonctionne en respectant ces limites. Le modèle de série limite le courant à 12 ampères et lorsqu’il est modifié par un tech nicien qualifié à l’aide du SA221KIT, le courant limite passe à 16 ampères.
Lorsqu’il est réglé sur 16 ampères il faut utiliser le cordon d’alimentation approprié et une source d’alimentation de 20 ampères.
La commande de limitation de la puissance moyenne permet de réduire la puissance pour permettre un fonctionnement avec une disponibilité de puissance limitée. Les transitoires à pleine puissance seront permises, mais si la puissance moyenne est excessive, la puissance sera limitée. En position 16 ampères (8 ampères CE), la puissance moyenne est limitée uniquement par la température de la bobine mobile. En position 12 ampères (6 ampères CE), avec la plupart des programmes musicaux, le limiteur ne sera actif qu’occasionnellement, en fonction du contenu musical. En position 8 ampères (4 ampères
CE), certains types de musique ne seront pas limités, principalement la musique sans basses profondes ou lorsque les basses ne sont pas traitées. La position 6 ampères (3 ampères CE) réduira significative ment la sortie lorsque le contenu musical contient des basses continues en dessous de 45 Hz. L’indicateur vert de mise sous tension s’assombrit pour indiquer que le limiteur de courant de ligne est actif.
8. Sortie Passe-Haut 50 Hz
Le SA221S propose une sortie XLR passe-haut (highpass) 50 Hz de niveau ligne destinée à fournir l’égalisation, le filtrage et l’alignement temporel appropriés pour utiliser les subwoofers SA315S avec les subwoofers SA221S. Cette sortie ne convient à aucune autre utilisation. Cette sortie ne doit pas être utilisée pour acheminer le signal à des enceintes à pleine bande. Normalement, elle devrait être utilisée avec le commutateur de passe-bas 50 Hz enfoncé.
9. Commutateur Passe-Bas 100 Hz / 50 Hz
Ce commutateur permet d’utiliser les subwoofers SA221S avec les subwoofers SA315S. Combiné avec la sortie Passe-Haut (Highpass) 50
Hz, ceci assurera un filtrage et un alignement temporel appropriés.
Pour obtenir le manuel de utilisateur visitez notre site Web à http://www.yorkville.com/manuals/ ou, si vous avez besoin d’une version imprimée appelez-nous au 905-837-8777
Yorkville Sound
550 Granite Court
Pickering, Ontario
Canada L1W 3Y8
Auto Attend: (905) 837-8550 Fax: (905) 837-8746 www.yorkville.com
Publicité
