Minigel-Twin user manual

Minigel-Twin user manual
Minigel Family
Vertical
Polyacrylamide Gel electrophoresis Apparatus
Instruction Manual
Modell
Minigel
Minigel-Twin
Multigel
Multigel-Long
Maxigel
Order No.
010-000, 010-030, 010-040
010-100, 010-130, 010-140
010-200, 010-220, 010-230
010-300, 010-320, 010-330
010-400, 010-430, 010-440
!! Warning !!
Please read these instructions carefully
before using this apparatus!
Biometra GmbH
Rudolf-Wissell-Str. 30
D-37079 Goettingen
Tel:
+49 (0)5 51 50 68 6-0
Fax:
+49 (0)5 51 50 68 6-66
e-mail: [email protected]
internet: http://www.biometra.de
Service Department
Rudolf-Wissell-Str. 14-16
D-37079 Goettingen
Tel.: +49 (0)5 51 50 68 6-10 or -12
Fax.: +49 (0)5 51 50 68 6-11
e-mail: [email protected]
This document describes the state at the time of publishing. It needs not necessarily
agree with future versions.
Subject to change!
Fastblot Instruction Manual, 2009/11
1.0 Intended Uses And Specifications
The Biometra Slabgels are intended to be used for the fractionation of Proteins and
DNA/RNA molecules in an vertical Polyacrylamid gelelectrophoresis
The Minigel (Code-No. 010-000) comes complete with all the acessories needed to
cast and run 8.6 x 7.7 cm
(w x l) gels. Acessories included with this system are:
- main chamber for vertical gels (8.6 x 7.7 cm), including cooling device and safetylid.
- One notched glass plate with straight edges (Code-No. 010-003).
- One glass plate with fixed 1.0 mm spacers (Code-No. 010-001).
- One comb, 10 wells, 1.0 mm (Code-No. 010-011).
- One silicone rubber seal, 1.0 mm (Code-No. 010-006).
- One sets of clips (à 3 pieces) (Code-No. 010-007)
- One Manual
The Minigel-Twin (Code-No. 010-100) comes complete with all the acessories
needed to cast and run 8.6 x 7.7 cm (w x l) gels. Acessories included with this system
are:
- main chamber for vertical gels (8.6 x 7.7 cm), including cooling device and safetylid.
- Two notched glass plates with straight edges (Code-No. 010-003).
- Two glass plates with fixed 1.0 mm spacers (Code-No. 010-001).
- Two combs, 10 wells, 1.0 mm (Code-No. 010-011).
- Two silicone rubber seals, 1.0 mm (Code-No. 010-006).
- Two sets of clips (à 3 pieces) (Code-No. 010-007)
- One Manual
Accessories:
Glass plates:
Glass plates with fixed 1.0 mm spacers
Glass plates with fixed 0.6 mm spacers
Notched glass plate with straight edge
Notched glass plate with inclined edge
Code-No. 010-001
Code-No. 010-002
Code-No. 010-003
Code-No. 010-004
Combs, 1 mm:
1 well (preparative)
2 wells
3 wells
5 wells
10 wells
10 wells for big samples or high protein concentrations
20 wells
Code-No. 010-008
Code-No. 010-022
Code-No.010-009
Code-No.010-010
Code-No.010-011
Code-No.010-023
Code-No.010-012
Combs, 0.6 mm:
1 well (preparative)
2 wells
3 wells
5 wells
10 wells
10 wells for big samples or high protein concentrations
20 wells
Code-No. 010-013
Code-No. 010-021
Code-No.010-014
Code-No.010-015
Code-No.010-016
Code-No.010-024
Code-No.010-020
Others:
Silicone rubber seal, 1.0 mm
Silicone rubber seal, 0.6 mm
Clips 3 pcs.
Code-No. 010-005
Code-No. 010-006
Code-No. 010-007
1
The Multigel (Code-No. 010-200) comes complete with all the acessories needed to
cast and run 11 x 7 cm (w x l) gels. Acessories included with this system are:
- main chamber for vertical gels (11 x 7 cm), including cooling device and safety-lid.
- Two notched glass plate with straight edges (Code-No. 010-201).
- Two glass plates with fixed 1.0 mm spacers (Code-No. 010-202).
- Two combs, 24 wells, 1.0 mm (Code-No. 010-204).
- Two silicone rubber seals, 1.0 mm (Code-No. 010-205).
- Three sets of clips (à 3 pieces) (Code-No. 010-007)
- One Manual
The Multigel-Long (Code-No. 010-300) comes complete with all the acessories
needed to cast and run 11 x 12 cm (w x l) gels. Acessories included with this system
are:
- main chamber for vertical gels (11 x 12 cm), including cooling device and safety-lid.
- Two notched glass plate with straight edges (Code-No. 010-301).
- Two glass plates with fixed 1.0 mm spacers (Code-No. 010-302).
- Two combs, 24 wells, 1.0 mm (Code-No. 010-204).
- Two silicone rubber seals, 1.0 mm (Code-No. 010-303).
- Four sets of clips (à 3 pieces) (Code-No. 010-007)
- One Manual
Accessories:
Glass plates:
Glass plates with fixed 1.0 mm spacers
notched glass plate
(Code-No. 010-202)
(Code-No. 010-201)
Combs:
12 wells, 1,0 mm
24 wells, 1,0 mm
(Code-No. 010-203)
(Code-No.010-204)
Others:
Silicone rubber seals, 1.0 mm
(Code-No. 010-205)
Clips 3 pcs.
(Code-No. 010-007)
12-channel pipette, variable, 5-50 μl volume in 0.1 μl steps (Code-No. 010-206)
2
The Maxigel (Code-No. 010-400) comes complete with all the acessories needed to
cast and run 17 x 18 cm (w x l) gels. Acessories included with this system are:
- main chamber for vertical gels (17 x 18 cm), including cooling device and safety-lid.
- Two notched glass plate with straight edges (Code-No. 010-401).
- Two glass plates with fixed 1.0 mm spacers (Code-No. 010-402).
- Two combs, 12 wells, 1.0 mm (Code-No. 010-404).
- Two silicone rubber seals, 1.0 mm (Code-No. 010-417).
- Three sets of clips (à 3 pieces) (Code-No. 010-007)
- One set of Maxi-clips (à 4 pieces) (Code-No. 010-416)
- One Manual
Accessories:
Glass plates:
Glass plates with fixed 1.0 mm spacers
notched glass plate
(Code-No. 010-402)
(Code-No. 010-401)
Combs:
12 wells, 1.0 mm
18 wells, 1.0 mm
24 wells, 1.0 mm
1 well (2 marker lanes), 1.0 mm, preparative
(Code-No. 010-404)
(Code-No. 010-405)
(Code-No. 010-406)
(Code-No. 010-407)
Others:
Silicone rubber seals, 1.0 mm
Clips, 3 pcs.
Maxi-Clips, 4 pcs.
(Code-No. 010-417)
(Code-No. 010-007)
(Code-No. 010-416)
3
2.0 Safety and Warning Notices
2.1 Definition of Symbols
Symbol
Definition
Caution! Refer to instruction manual!
Danger! High voltage!
Fragile!
Using with direct current (DC).
2.2 General Safety Instructions
Delicate instuments! Handle with care!
Do not operate this equipment if buffer or water leaks from the
instrument, if cracks are present in the body or the safety cover or if the
electrical connection cables are worn or frayed.
Make sure that the on/off switch of the used external Power Supply is
always free accessible.
the
Danger! High voltage!
The current to the cell, provided from the external Power Supply, enters
the unit through the lid assembly, providing a safety interlock to the
user. Current to the cell is broken when the lid is removed.
Do not attempt to circumvent this safety interlock, and always turn
Power Supply off before removing the lid, or when working with
the cell in any way.
4
Power to the instrument is supplied by an external DC voltage Power
Supply. The output of this Power Supply must be isolated from external
ground to issue that the DC voltage output floats with respect to round.
(All Biometra Power Supplies meet this safety requirement!)
Never place the instrument on top of a Power Supply.
Using the cooling option do not mix up the "in" and "out" plugs for the
cooling water. The connection for the water cooling with the smaller
diameter is the inlet the connection with the bigger diameter is the
outlet.
Best cooling is obtained using a refrigerated circulator (chiller) with a
temperature of 5°C.
(Attention: Reduce flow rate to max. 0.5 - 1 l/min and use no organic
solvents or alcohol !)
Operating Conditions:
max. V (DC)
max. mA
max. W
max. Temp.
Minigel
400
25 (1 Gel)
10
50°C
Minigel-Twin
400
50 (2 Gele)
20
50°C
Multigel
400
70 (2 Gele)
28
50°C
Multigel-Long
450
70 (2 Gele)
32
50°C
Maxigel
500
120 (2 Gele)
60
50°C
Lengthy transfer times are not recommended. Do not leave the
instrument unattended. Joule heat can be generated during
electrophoresis. Electrophoresis runs longer than 4-6 hours at max.
settings can damage the unit.
Do not use alcohol (e.g. methanol, ethanol) or organic solvents for
cooling or cleaning the apparatus.
5
This products are designed and certified to meet EN 61010-1 safety
standards.
Certified products are safe to use when operated in accordance with
the instruction manual.
This instruments should not be modified or altered in any way.
Alteration of this instruments will void the warranty, void the EN61010-1
certification, and create a potential safety hazard.
6
3.0 Set Up
3.1 Unpack and Check
Unpack and carefully examine the electrophoresis unit. Report any damage to
BIOMETRA. Do not attempt to operate this device if physical damage is present.
Save all packing material if damage is found.
!! Attention !!
Please fill out and send back the warranty registration card. This is
important for you to claim to full warranty: both parts and repair are
covered within the full warranty period!
3.2 Electricity Supply
This electrophoresis chamber has been designed to operate with D.C. current.
Warning: This supply must not be earthed.
3.3 Important Electrical Safety Notes
Do not operate this equipment if any of the following conditions exist:
- If buffer leaks from the main electrophoresis chamber.
- If cracks are present in the electrophoresis chamber or safety cover.
- If the electrical connection cables are worn or frayed.
4.0 Location
Place the chamber in proximity to the Power Pack with which it is to be connected.
Be sure to place the chamber in a safe, dry location away from the edge of the
working surface.
7
5.0 Handling
5.1 Mounting the glass plates:
Put one silicone rubber seal between two thoroughly cleaned glass plates (one glass
plate with fixed spacers, one notched glass plate) and fix the glass plate set with:
1 clip right, 1 clip left and 1 clip at the bottom for Minigel and Minigel-Twin,
1 clip right, 1 clip left and 2 clips at the bottom for Multigel,
2 clips right, 2 clips left and 2 clips at the bottom for Multigel-Long,
2 clips right, 2 clips left and 2 Maxi-clips at the bottom for Maxigel.
Attention:
Acrylamide is a neurotoxin. Handle gels and gel solutions with care
and wear rubber gloves.
5.2 Running Gel:
Minigel / Minigel-Twin:
About 6 ml of gel solution are needed if 1.0 mm spacers are used. Immediately after
addition of TEMED and ammoniumpersulfate, pour the solution between the glass
plates (up to 4 cm) and overlay it carefully with 0.2 ml of bidistilled water.
Multigel:
About 9 ml of gel solution are needed if 1.0 mm spacers are used. Immediately after
addition of TEMED and ammoniumpersulfate, pour the solution between the glass
plates (up to 5 - 5.5 cm) and overlay it carefully with 0.8 ml of bidistilled water.
Multigel-Long:
About 12 ml of gel solution are needed if 1.0 mm spacers are used. Immediately after
addition of TEMED and ammoniumpersulfate, pour the solution between the glass
plates (up to 9 - 9.5 cm) and overlay it carefully with 0.8 ml of bidistilled water.
Maxigel:
About 30 ml of gel solution are needed if 1.0 mm spacers are used. Immediately after
addition of TEMED and ammoniumpersulfate, pour the solution between the glass
plates (up to 16 cm from the bottom) and overlay it carefully with bidistilled water.
Polymerisation (visible by the formation of a sharp boundary between gel and
overlay) takes about 20-40 minutes. Remove the water completely from the surface
of the polymerised gel with a sheet of filter paper.
8
5.3 Stacking Gel
Minigel / Minigel-Twin:
About 2 ml of stacking gel solution is required.
Multigel and Multigel-Long::
About 2.5 to 3 ml of stacking gel solution is required.
Maxigel:
About 3.5 ml of stacking gel solution is required.
Insert the comb after pouring the solution between the glass plates. The
polymerisation should take about 20 - 30 minutes.
5.4 Assembly
Remove the silicone rubber seals and combs, fill up the lower buffer reservoir with
the running buffer and mount the plates onto the apparatus. Make shure that there
are no air bubbles present at the bottom of the running gel. You may achieve this by
tilting the plates when dipping them into the buffer. After fixing the glass plate sets
with the clamps onto the body of the electrophoresis apparatus fill up the upper buffer
reservoir with buffer and remove the comb carefully. Wash the slots with buffer.
5.5 Sample Application
Dissolve the sample in SDS-sample buffer and carefully load it into the slots of the
stacking gel. If you are using samples precipitated with trichloroacetic acid, neutralise
them first with Tris base solution.
As the 24 well comb for Multigel and Multigel-Long (Code-No. 010-204) is compatible
with the multichannel pipet, multiple loading of samples is possible.
5.6 Electrophoresis
Mount the safety lid. Switch on the power supply e.g. Power Pack P20 (Code-No.
040-400) or Power Pack P25 (Code-No 040-800) from Biometra. Be aware that the
plus pole (in red) is connected to the lower buffer reservoir.
The following conditions can be recommended for a gel with a 10% Running Gel and
1mm spacers:
Minigel / Minigel-Twin:
Stacking gel
10 mA
Running (Separation) gel 25 mA
9
Multigel and Multigel-Long:
Stacking gel
10 - 20 mA
Running (Separation) gel 25 - 35 mA
Maxigel:
Stacking gel
15 - 25 mA
Running (Separation) gel 50 - 60 mA
The values may vary with gel concentration.
Mulitgel, Multigel-Long and Maxigel:
A more homogeneous run with even sharper bands can be achieved by water
cooling.
Do not mix up the "in" and "out" plugs for the cooling water.
Max. flow rate (unpressurized) = 0.5 – 1 l/min
Stop the electrophoresis when the bromphenol blue band has nearly reached the
bottom of the running gel.
Switch off the Power Pack and open the safety lid after the plugs of the Multigel have
been disconnected from the Power Pack.
5.7 Staining and Destaining
Slide the gel carefully from the glass plates into the Coomassie Brilliant Blue staining
solution and stain it for 30-60 minutes with gentle agitation. Fixation with
trichloroacetic acid is not necessary. Destain briefly with a solution of 45% ethanol,
10% acetic acid, 45% water andthen in a solution of 7% acetic acid in water.
5.8 Cleaning
Use only mild non-abrasive detergents.
DO NOT use alcohol (e.g. methanol, ethanol) or organic solvents (e.g.
acetone) on the electrophoresis unit.
DO NOT use chromosulfuric acid to clean the glass plates.
The system should never be autoclaved or placed in a microwave.
10
6.0 Solutions for SDS Polyacrylamide Gels used
6.1 Running Gel
Minigel and Minigel-Twin: (6 ml per gel)
Acrylamide conc. in %
7.5
10.0 12.5
30% acrylamide,
0.8% bisacrylamide
stock solution in ml
1.5
2.0
2.5
1.88 M Tris/HCl
pH 8.8 in ml
1.2
1.2
1.2
0.5% SDS in ml
1.2
1.2
1.2
dist. H2O in ml
2.1
1.6
1.1
TEMED in μl
5
5
5
ammonium persulphate sol.,
10% in μl
30
30
30
Multigel: (9 ml per gel)
Acrylamide conc. in %
7.5
30% acrylamide,
0.8% bisacrylamide
stock solution in ml
2.25
1.88 M Tris/HCl
pH 8.8 in ml
1.8
0.5% SDS in ml
1.8
dist. H2O in ml
3.15
TEMED in μl
8
ammonium persulphate sol.,
10% in μl
45
Multigel-Long: (12 ml per gel)
Acrylamide conc. in %
7.5
30% acrylamide,
0.8% bisacrylamide
stock solution in ml
3.0
1.88 M Tris/HCl
pH 8.8 in ml
2.4
0.5% SDS in ml
2.4
dist. H2O in ml
4.2
TEMED in μl
10
ammonium persulphate sol.,
10% in μl
60
15.0
17.5
3.0
3.5
1.2
1.2
0.6
5
1.2
1.2
0.1
5
30
30
10.0
12.5
15.0
17.5
3.0
3.75
4.5
5.25
1.8
1.8
2.4
8
1.8
1.8
1.65
8
1.8
1.8
0.9
8
1.8
1.8
0.15
8
45
45
45
45
10.0
12.5
15.0
17.5
4.0
5.0
6.0
7.0
2.4
2.4
3.2
10
2.4
2.4
2.2
10
2.4
2.4
1.2
10
2.4
2.4
0.2
10
60
60
60
60
11
Maxigel: (30 ml per gel)
Acrylamide conc. in %
7.5
10.0 12.5 15.0 17.5
30% acrylamide,
0.8% bisacrylamide
stock solution in ml
7.5 10.0 12.5 15.0 17.5
1.88 M Tris/HCl
pH 8.8 in ml
6.0
6.0
6.0
6.0
6.0
0.5% SDS in ml
6.0
6.0
6.0
6.0
6.0
dist. H2O in ml
10.5
8.0
5.5
3.0
0.5
TEMED in μl
25
25
25
25
25
ammonium persulphate sol.,
10% in μl
150 150 150 150 150
Attention:
The ammonium persulphate solution (10%) should be prepared fresh every day and
should be stored at 4°C (refrigerator).
12
6.2 Stacking Gel, 5%
Minigel and Minigel-Twin: (2 ml per gel)
0.33 ml
30% acrylamide, 0,8% bisacrylamide stock solution
0.4 ml
0.625 M Tris/HCl pH 6.8
0.4 ml
0.5% SDS
0.87 ml
dist. H2O
2 μl
TEMED
10 μl
10% ammonium persulphate sol.
Multigel and Multigel-Long: (4 ml per gel)
0.66 ml
30% acrylamide, 0,8% bisacrylamide stock solution
0.8 ml
0.625 M Tris/HCl pH 6.8
0.8 ml
0.5% SDS
1,74 ml
dist. H2O
4 μl
TEMED
20 μl
10% ammonium persulphate sol.
Maxigel: (6 ml per gel)
1.0 ml
30% acrylamide, 0,8% bisacrylamide stock solution
1.2 ml
0.625 M Tris/HCl pH 6.8
1.2 ml
0.5% SDS
2.6 ml
bidist. H2O
6 μl
TEMED
30 μl
10% ammonium persulphate sol.
Attention:
The ammonium persulphate solution (10%) should be prepared fresh every day and
should be stored at 4°C (refrigerator).
13
6.3 SDS-Sample Buffer
for SDS-PAGE gels under reducing conditions
2 ml
0.625 M Tris/HCl pH 6.8
0.2 g
SDS
5 ml
glycerol
0.5 ml
ß-mercaptoethanol
0.1 ml
bromophenol blue (1% in ethanol)
2.4 ml
dist. H2O
Dilute the sample buffer 1 to 1 with the sample.
6.4 Running Buffer pH 8.3 (5 liter)
15.1 g
72.0 g
5.0 g
Tris-Base
glycine
SDS
6.5 Staining Solution (1 liter)
2.0 g
Coomassie Brilliant Blue R 250
0.5 g
Coomassie Brilliant Blue G 250
425 ml
ethanol
50 ml
methanol
100 ml
acetic acid
425 ml
bidest. water
Stirr overnight; filtrate before use; store in dark bottle!
6.6 Destaining solution
fast destaining in:
45% ethanol
10% acetic acid
75% bidest. water
slow destaining in:
25% isopropanol
10% glacial acid
45% bidest. water
final destaining in:
7%
acetic acid in bidest. water
14
7.0 Service
Should you have any problems with this unit, please contact our service department
or your local Biometra dealer:
Biometra GmbH
Service Department
Rudolf-Wissell-Straße 14 - 16
D-37079 Goettingen
Phone:
+49 (0)5 51 50 68 6 - 10 or 12
Fax:
+49 (0)5 51 50 68 6 -11
e-mail:
[email protected]
If you would like to send the unit back to us, please read the following
return instructions.
Instructions for return shipment
• Return only defective devices. For technical problems which are not definitively
recognisable as device faults please contact the Technical Service Department at
Biometra (Tel.: +49 (0)5 51-50 88 1-10 or -12, Fax: +49 (0)5 51-50 88 1-11, e-mail:
[email protected]).
• Please contact our service department for providing a return authorization
number (RAN). This number has to be applied clearly visible to the outer box.
Returns without the RAN will be not be accepted!
• Important: Clean all parts of the instrument from residues, and of biologically
dangerous, chemical and radioactive contaminants. If the device is
contaminated, Biometra will be forced to refuse to accept the device.
The sender of the repair order will be held liable for possible damages
and losses resulting from insufficient decontamination of the device.
• Please prepare written confirmation (use the “Equipment Decontamination
Declaration” following on the next page) that the device is free of biologically
dangerous, chemical or radioactive contaminants. This confirmation must be
attached to the outside of the packaging.
• Use the original packing or a similarly robust packing when returning the device. If
not available, contact Biometra or your local distributor.
15
• Label the outside of the box with “CAUTION! SENSITIVE INSTRUMENT!” and the
RAN number sticker. Attach the Decontamination Declarartion!
• Please enclose a note which contains the following:
a)
b)
c)
the
Sender’s name and address,
Name of a contact person for further inquiries with telephone number.
Precise description of the fault, which also reveals during which procedures
fault occurred, if possible.
16
8.0 Equipment Decontamination Certificate
To enable us to comply with german law (i.e. §71 StrlSchV, §17 GefStoffV and §19 ChemG)
and to avoid exposure to hazardous materials during handling or repair, please complete this
form, prior to the equipment leaving your laboratory.
COMPANY / INSTITUTE
__________________________________________________
ADDRESS
______________________________________________________________
PHONE NO
_________________________
E-MAIL
______________________________________________________________
EQUIPMENT
FAX NO_________________________
Model
______________
Serial No
______________
______________
______________
______________
______________
______________
______________
If on loan / evaluation Start Date: __________________
Finish Date __________________
Hazardous materials used with this equipment:
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
Method of cleaning / decontamination:
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
The equipment has been cleaned and decontaminated:
NAME __________________________________ POSITION _______________________
(HEAD OF DIV./ DEP./ INSTITUTE / COMPANY)
SIGNED ________________________________ DATE ____________________________
PLEASE RETURN THIS FORM TO BIOMETRA GMBH OR YOUR LOCAL BIOMETRA
DISTRIBUTOR TOGETHER WITH THE EQUIPMENT.
PLEASE ATTACH THIS CERTIFICATE OUTSIDE THE PACKAGING. INSTRUMENTS
WITHOUT THIS CERTIFICATE ATTACHED WILL BE RETURNED TO SENDER.
17
General Information for Decontamination:
Please contact your responsible health & safety officer for details.
Use of radioactive substances:
Please contact your responsible person for details.
Use of genetically change organism or parts of those:
Please contact your responsible person for details.
18
9.0 Notes
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
19
EU - Declaration of Conformity
Göttingen, March 2009
im Sinne der EG-Richtlinie über elektrische Betriebsmittel zur Verwendung innerhalb bestimmter
Spannungsgrenzen 73/23/EWG.
following the EC directive about electrical equipment for use within certain limits of voltage 73/23/EEC.
Hiermit erklären wir, daß folgende Slabgele
Herewith we declare that the following Slabgel
Systems
Typen / types:
Minigel, Minigel-Twin, Multigel, Multigel-Long,
Maxigel
Best.-Nr. / Order No.
010-000, 010-030, 010-040, 010-100, 010-130, 010-140, 010-200,
010-220, 010-230, 010-270, 010-300, 010-320, 010-330, 010-400,
010-430, 010-440
den grundlegenden Anforderungen der
corresponds to the basic requirements of
EG-Niederspannungsrichtlinie 73/23/EWG entsprechen.
EC low voltage directive 73/23/EEC.
Folgende harmonisierte Normen wurden angewandt:
The following harmonized standards have been used:
EN 61 010 - 1
(in Anlehnung / corresponding to)
EN 61 010 - 1/A2
(in Anlehnung / corresponding to)
Dr. Jürgen Otte
Quality Manager
20
Warranty
This laboratory instrument is produced with the highest practical standards of
materials, workmanship, and design. The design and manufacture of parts have been
conceived with one purpose - to produce units which will give satisfactory service.
Biometra GmbH guarantees this unit to be free from defects in materials or
workmanship under normal use or service for 24 month from date of shipment. If,
during this time, this unit proves defective in materials or workmanship, Biometra
GmbH will repair or replace it free of charge if returned to us prepaid. This guarantee
does not cover damage in transit, damage caused by carelessness, misuse or
neglect, or unsatisfactory performance as a result of conditions beyond our control;
or consequential losses as a result of failure of our product.
Biometra GmbH
Rudolf-Wissell-Str. 30
D-37079 Göttingen
Postfach 1544
D-37005 Göttingen
Tel: ++49 – (0)5 51 / 50 68 6-0
Fax: ++49 – (0)5 51 / 50 68 6-66
e-mail: [email protected]
internet: http://www.biometra.de
Service Department
Rudolf-Wissell-Str. 14-16
D-37079 Göttingen
Tel.: ++49 – (0)5 51 / 50 88 1-10 or -12
Fax.: ++49 – (0)5 51 / 50 88 1-11
e-mail: [email protected]
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement