User Manual

User Manual
TA+POX, TA+HUX, TA+SOC
User manual
ISDN Terminal Adapter
Version
Date
1.80D
09.2005
© Stollmann Entwicklungs- und Vertriebs- GmbH
Component name:
Article No.:
TA+POX/TA+HUX, TA+SOC User manual
621-52017
1.80D/02.2005
TA+POX, TA+HUX, TA+SOC User manual
Exclusion of Liability
Exclusion of Liability
The present manual by Stollmann Entwicklungs- und Vertriebs-GmbH (hereinafter
referred to as Stollmann) reflects the present state of the art of the products
described therein. We have endeavored to give a description that is as complete
and clear as possible in order to make work with our products as easy as possible
for you. All the same, the manual may contain technical inaccuracies and typing
errors. As a result of the rapid advance in the art, we must also reserve the right to
incorporate technical alterations and developments without separate advance
notice.
That is why Stollmann does not give any warranty for the contents of the manual
and for its continuing applicability.
Nor is Stollmann liable for any loss of information or any incorrect use of information
that might result from consultation of the manual. Particularly, Stollmann is not liable
for damage, nor indirect damage (including damage caused by financial loss, delays
affecting business transactions or interruptions of business and similar
consequences), arising from the use or improper use of this manual, not even in the
case where it was pointed out to Stollmann or an agent of Stollmann that such
damage might be sustained. This does not, of course, affect our legal liability for
damages based on any intent or gross negligence.
With respect to the data given in this manual, Stollmann does not warrant the nonexistence of industrial property rights (trademarks, patents, utility models, etc.). Nor
are trade names, brand names, company names and product names in general use
but are subject to the relevant trademark, patent, utility model and registered design
rights.
The information must neither in whole nor even in part be copied, translated,
reproduced or in any other way transferred to or stored on any electronic medium or
other machine.
The purchase and use of software are governed by the General Conditions of
Delivery and Payment as well as the Terms of License of Stollmann.
If any of the provisions on the exclusion of tina is a registered liability or on use are
or become ineffective for statutory reasons, this will not affect the other provisions.
trademark of Stollmann Entwicklungs- und Vertriebs-GmbH.
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
Table of Contents
Table of contents
1
Introduction ..................................................................................................... 1
1.1
Product description ...................................................................................... 1
1.2
Service ......................................................................................................... 2
1.3
License......................................................................................................... 2
2
Installation....................................................................................................... 3
2.1
Contents....................................................................................................... 3
2.2
Installation procedure................................................................................... 3
2.3
Displays and control elements TA+POX ...................................................... 4
3
Using the TA+POX, TA+HUX, TA+SOC ......................................................... 6
3.1
3.1.1
3.2
X.3 command set - integrated PAD ............................................................. 7
X.3 Parameter of the integrated PAD ....................................................... 8
AT command set ........................................................................................ 16
3.2.1
ISDN specific AT commands .................................................................. 26
3.2.2
AT command S register set .................................................................... 30
3.2.3
AT result codes....................................................................................... 31
3.3
Serial status lines....................................................................................... 33
3.4
Automatic call establishment...................................................................... 36
3.5
ISDN access control, security callback, leased line................................... 38
3.5.1
ISDN access control ............................................................................... 38
3.5.2
Security callback..................................................................................... 39
3.5.3
ISDN leased line (option) ....................................................................... 39
3.6
B channel connections with external IOM use (option) .............................. 40
3.7
User to User Signaling UUS1..................................................................... 40
3.8
Subaddressing ........................................................................................... 41
3.9
X.25 address translation table ................................................................... 42
© Stollmann Entwicklungs- und Vertriebs-GmbH
i
TA+POX, TA+HUX, TA+SOC User manual
Table of contents
3.10
X.25 D channel rerouting ........................................................................... 43
3.11
Using Multilink PPP.................................................................................... 44
3.11.1
Restrictions on Windows95 ................................................................ 44
3.11.2
Bandwidth on demand ("BOD")........................................................... 45
4
TA+Configurator command set ..................................................................... 46
4.1
Configuring the TA+POX with AT commands ............................................ 46
4.2
Configuring the TA+POX with X.3 PAD...................................................... 46
4.3
Configuring the TA+POX after power on.................................................... 47
4.4
Remote Configuration using the TA+Configurator commands................... 48
4.4.1
Remote access control ........................................................................... 49
4.5
List of TA+Configurator commands............................................................ 50
4.6
Software update ......................................................................................... 75
5
Diagnostic and error messages .................................................................... 76
5.1
Error messages from AT command set ...................................................... 76
5.2
Error messages of the integrated PAD....................................................... 77
5.3
Table of ISDN causes and their explanation (DSS1) ................................. 78
5.4
X.25 causes and their explanation ............................................................. 80
5.4.1
X.25 causes in Clear packet................................................................... 80
5.4.2
X.25 diagnostic codes ............................................................................ 81
5.4.3
X.25 causes in Restart packet ................................................................ 85
5.4.4
X.25 causes in Reset packet .................................................................. 85
5.5
CAPI causes and their explanation ............................................................ 86
5.6
Diagnostic using the internal Trace............................................................ 88
6
ii
1.80D/09.2005
Appendix ....................................................................................................... 93
A1:
Technical data TA+POX, TA+HUX, TA+SOC ............................................ 93
A2:
LED displays TA+POX ............................................................................... 94
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
Table of Contents
A3:
TA+HUX V1 Mechanical dimensions of the module V1................................. 95
A4:
TA+HUX V1 Serial Interface Connector P1 ................................................ 96
A5:
TA+HUX V1 ISDN interface connector P2 ................................................. 97
A6:
TA+HUX V1 IOM Interface connector P3................................................... 97
A7:
TA+SOC V2 Mechanical dimensions of the module...................................... 98
A8:
TA+SOC V1 connector X1 to X6 ................................................................ 99
A9:
TA+POX Pinout of the ISDN connector.................................................... 100
A10:
TA+POX Pinout of the V.24/V.28 interface (DSUB 9) .............................. 100
A11:
TA+POX Cable layout for connection of terminals with 25 pin connectors
(male or female) .......................................................................................... 101
A12:
TA+POX Cable layout to connect a PC with 9 pin male plug through a
serial COM-port........................................................................................... 102
© Stollmann Entwicklungs- und Vertriebs-GmbH
iii
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
1. Introduction
1 Introduction
We are very pleased to see that you have bought a Stollmann product and would
like to express our appreciation.
This documentation is valid for the product:
•
•
•
TA+POX
TA+HUX
TA+SOC hardware version 2
Please refer to the appendixes about differences between the products.
1.1 Product description
The TA+POX is an ISDN terminal adapter with the following functions. You can see
it as a digital replacement for an analogue modem.
• The TA+POX connects devices with a serial port to the ISDN. It gives access to
other devices connected to the ISDN network.
• Data can be transmitted either over the D- or B-channel with the following rates:
- by using the transmission method V.110 or V.120 in B channel.
- by using the transmission method X.75, PPP or HDLC in B channel.
- call a host connected to the X.25-network (X.25 in B or D channel).
- call a host connected to an ISDN-X.31 subscriber line
• Data can be transmitted either over the D- or B-channel with the following rates:
- Transmission via D-channel with 9600 bps (X.31-D)
- Transmission via B-channel with 64000 bps (X.31-B)
• The connected device can drive the TA+POX by using
- asynchronous PAD (X.3) commands
- asynchronous AT commands
- automatic call
To work with TA+POX you need
• an ISDN Basic Rate Interface (BRI) (replacing an analogue telephone line). The
basic rate access can be ordered by your local telephone company or PTT.
• a PC with a terminal emulation to configure the TA+POX
© Stollmann Entwicklungs- und Vertriebs-GmbH
1
TA+POX, TA+HUX, TA+SOC User manual
1. Introduction
1.80D/09.2005
1.2 Service
By using the call number +49 40 89088-291 you can connect up to an asynchronous
support server, which uses the B channel protocol X.75 (please use command
ATB10 to set up the correct B channel protocol).
By using the call number +49 40 89088-293 you can connect up to an asynchronous
support server, which uses the B channel protocol X.25 (please use command
ATB20 to set up the correct B channel protocol).
To LOGIN please use
name:
guest
password: guest.
X.31 connection:
The German Telecom offers a test access point for X.25 (echo generator) with the
following X.121 number (Datex-P): 40400049912
HINT: For access to the German DATEX-P network from an X.31-D basic
rate interface in Germany you have to use the dialing prefix 0262 preceding
the X.25 calling number (i.e. call 0262 40 4000 49912).
After the connection is established the echo generator will echo all received text
string in X.25 packets.
1.3 License
The following license numbers for the connection to the ISDN are given by
CE-0682 X for Europe (EC), Switzerland, Norway:
TA+POX and TA+HUX are conform to the European safety requirements IEC 60
950. Please use only the delivered power supply or an original replacement from
Stollmann. Connect the TA+POX only to the S bus interfaces with SELV (Safety
Extra Low Voltage) related to EN60950.
The TA+POX and TA+HUX are conform to the European rules of EMC. EN50081-1,
here EN55022 Class B, for electromagnetic field emission and EN50082-1 for
immunity against electromagnetic interference.
2
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
2. Installation
2 Installation
2.1 Contents
This packet contains the following items:
•
•
•
•
•
ISDN Terminal adapter TA+POX in desktop box
Mains plug power supply adapter (only TA+POX)
ISDN interface cable (only TA+POX)
DTE interface serial cable (only TA+POX)
This user manual
2.2 Installation procedure
•
•
•
Connect the serial port (DTE) of the TA+POX to the serial port (COM port) of
the PC by using the supported DTE interface serial cable.
Please make sure that the COM-port of the PC is not used for other purposes
or by other communication programs.
Connect the ISDN port of the TA+POX to the basic rate interface (BRI) of the
ISDN using the delivered ISDN cable.
Connect the power supply with the TA+POX and plug it into mains.
Please reference to page 4 for selecting the correct plug for interfacing.
Now the power-up sequence described in chapter 2.3 should appear.
The TA+POX is now ready for use, please refer to the next chapter for the
configuration to use the PC together with the TA+POX.
© Stollmann Entwicklungs- und Vertriebs-GmbH
3
TA+POX, TA+HUX, TA+SOC User manual
2. Installation
1.80D/09.2005
2.3 Displays and control elements TA+POX
For interfacing the module TA+HUX please refer to the appendix.
At the back of the TA+POX you will find the connectors for the following devices:
PWR
DTE V.24
ISDN
Fig. 2: Back view of the desktop model TA+POX
PWR:
ISDN:
DTE:
external power supply (5V DC)
ISDN interface
V.24 interface for DTE, i.e. a PC
You can control the status of the TA+POX via 8 LEDs at the front side.
L1
B1
R DCD
L2
B2
T
DTR
Fig. 3: Front view of the desktop model TA+POX
The 4 LEDs at the right show the status of the serial interface to the PC:
T:
shows activity of transmitted data from the terminal (DTE to TA)
R:
shows activity of receiving data from the ISDN line (TA to DTE)
DTR : shows the status of DTR line, i.e. the terminal is trying to connect via
the TA+POX
DCD : represents the status of the DCD line (V.24); shows normally the
connection to an access server.
Both LEDs, B1 and B2, show the connection state of the ISDN B channels:
If one or both LED's are ON, the B channel is occupied due to an incoming or
outgoing connection.
4
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
2. Installation
Both of the LEDs, L1 and L2, show the overall status of the TA+POX in coded form.
The following list describes the view for an error free power on sequence of the
TA+POX.
Status
1.
2.
3.
L1
L2
Θ
Active phase, ISDN ok
⊗
Connected, ISDN data connection established ⊗
Θ
O
⊗
Power-On-Phase, wait
LED Legend:
⊗
Θ
O
(about 2 sec)
On
Continuously blinking
Off
A complete list you can find in the appendix "LED displays"
© Stollmann Entwicklungs- und Vertriebs-GmbH
5
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3 Using the TA+POX, TA+HUX, TA+SOC
You can select different operation modes for the TA+POX. These operating modes
are used to setup ISDN connections and to configure the TA+POX.
Supported operating modes:
• X.3 asynchronous mode to connect asynchronous devices that drive a PAD X.3
interface
• asynchronous mode for devices that need the AT command set
• Automatic dialing deriving from DTR or TxD or always connected
You can configure the TA+POX in the following ways:
• by using the X.3 command set entered by the locally connected PC.
• by using the AT command set entered by the locally connected PC.
• by using TA+ configuration commands entered by the locally connected PC.
• by using TA+ configuration commands entered via the ISDN line (remote
configuration).
6
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
3.1 X.3 command set - integrated PAD
If you connect an asynchronous DTE to the X.31-service, you can use the integrated
PAD of the TA+POX. You can use for example the command stat to see the status
of the connection.
To setup PAD mode please use the configuration command “cmds = 1“.
The following PAD-Commands regarding the specifications X.28/X.29 are
supported:
•
(dot)
Displays PAD identification
[Pxxx-][R ][N<nuipwd> ][G<cug> ]X25number[I<ISDNnumber>][D<userdata>]
Establishes an X.25 connection
P : use packet size xxx for X.25 connection
R : request the facility reverse charging
G : access to X.25 closed user group
O : Outgoing call from X.25 closed user group
N : use NUI and password with call setup, allowed chars: a-z, A-Z, 0-9.
(overrides setting of nui configuration command)
X25number : dialed X.25 call number
ISDNnumber : ISDN call number for a dialed B channel connection
D : separator for user data: "D", "P" or ","
clr
Clears an X.25 connection
stat
Showing the PAD connection status
set
Set the PAD Profile to Profile 0
set x:n
Set the PAD Profile parameter x to value n
Note: PAD parameter can be stored using the command “exec save“.
prof x
Configures to the PAD Profile x, x = 0..7, 90, 91
Note: PAD parameter can be stored using the command “exec save“.
prof?
Displays the configured PAD Profile values
par [x][,x]
Displays all configured PAD Profile values or the PAD parameter x
“par“ without parameter displays all parameter.
© Stollmann Entwicklungs- und Vertriebs-GmbH
7
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
ver
1.80D/09.2005
Displays the version number
exec <cmd> Executes one TA+configuration command, for definition of commands
see page 50.
3.1.1 X.3 Parameter of the integrated PAD
Using the PAD command “set x:n“ you can change the parameter according to ITU
specification X.3.
After changing one or more X.3 parameter you can store the change non volatile by
issuing “exec save”. The stored parameter can be reloaded with the command “exec
load“.
After an X.25 connection is cleared the PAD parameter will be reset to the last
active profile (or default).
International Parameters 1 through 12
1
Enable (disable) switch to command mode
Defines whether the terminal user may switch from data to command
mode (e.g. to change a X.3 parameter), and - if he may - which key(s)
must be pressed to make the switch.
Valid Parameter Values:
0
Switch to command mode disabled.
1
Switch to command mode enabled
switch by pressing the key combination <CTRL>+P (hexadecimal 10,
decimal 16)
n
Switch to command mode enabled
switch by entering the ASCII character, that corresponds to the
parameter value n (decimal integer value in the range between 32
and 126).
2
Echo
Determines whether a character will be echoed to the terminal data
transfer mode.
Valid Parameter Values:
0
No echo
1
Echo
8
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
3
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Data Forwarding Characters
This parameter defines a control character to be used as the Data
Forwarding Character. This character can be used to force the
transmission of the collected data to the other end, even when the
defined packet size has not yet been reached.
Valid Parameter Values:
0
Only send full packets, thus no Data Forwarding Character
2
< > or <CR>
6
<ESC>, <BEL>, <ENQ>, <ACK>,<CR>
18
<ETX>, <EOT>,<CR>
128 All ASCII control codes, which are not listed above
Regardless of the value set in parameter 3, the data packet will always be
forwarded under any of the following conditions:
when the input buffer holds a full data packet (128 bytes) and
parameter 15 is set to 0 (zero)
when the input buffer is full (512 Bytes) and parameter 15 is set to 1 ;
in this case, one data packet will be sent and the remaining data will
be shifted forward in the input buffer
after the first character of a PAD command is entered
following the entry of the BREAK signal (command INTD) - also see
parameter 7
after the timeout of the timer set with parameter 4
4
Timer for Data Forwarding
Defines the timeout interval, following which the collected data will be
sent as a data packet even if the defined packet size was still not
reached.
The timer is reset each time a data packet is sent, even if it was sent
as the result of the Data Forwarding Character (see parameter 3).
Valid Parameter Values:
0
No timeout, thus no time interval
1
Immediate transfer, thus each character is immediately transferred as
a data packet.
n
n time interval in units of 50 msec. (1/20 of a second) and the value
must be an integer in the range from 2 to 255.
Example: n = 40 => time out interval of 2.0 seconds
A data transfer timeout is only permitted, when parameter 15 is set to 0
(zero).
© Stollmann Entwicklungs- und Vertriebs-GmbH
9
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
5
6
1.80D/09.2005
Control of additional devices
! not implemented, all values ignored !
Displaying PAD Messages
Defines, whether the PAD messages should be displayed. PAD
messages are service signals, that the PAD generates in response to
PAD commands.
Valid Parameter Values:
0
No display of PAD messages
1
Display of X.28-PAD-Messages (ITU) without PAD-Prompt.
5
Display of X.28-PAD-Messages (ITU) with PAD-Prompt.
9
Display of DATEX-P PAD-Messages without PAD-Prompt.
13
Display of DATEX-P PAD-Messages with PAD-Prompt.
17
21
+32
+64
Display of extended PAD-Messages without PAD-Prompt.
Display of extended PAD-Messages with PAD-Prompt.
To add one of the following features, add the described value to one of
the previous selected:
Suppress X.25 address and ISDN no. when connected
Display CAPI error cause.
7
Handling the BREAK Signal
Defines, how the PAD should react, when it receives a BREAK signal
from the terminal of the other communications partner (command
INTD).
Valid Parameter Values:
0
No reaction
1
Send Interrupt packet
2
Send Reset packet
5
Send Interrupt and break packet
8
Change to command mode (can be useful when parameter 1 is set to 0
(zero).
21
Discard local data and send Interrupt and break packet
8
Display Received Data ON/OFF
Defines, whether received data should be displayed on the screen.
Valid Parameter Values:
0
Display all received data.
1
Don't display the received data.
10
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
9
10
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Fill Characters Following a Carriage Return (<CR>)
Defines, how many fill characters (<NULL>) the PAD should insert into
the character string following a <CR> (carriage return).
Valid Parameter Values:
0
No fill characters <NULL>
n
Number of fill characters <NULL> following a <CR>.
n is an integer in the range from 1 to 255.
Note: This parameter is ignored for output to the screen, since the fill
characters serve no useful function on a screen display (left over from the
days of the teletype).
Screen Line Width
not supported
11
Local baudrate (Read only)
Displays actual used baudrate on asynchronous line.
1: 1200 bit/s
2: 2400 bit/s
3: 4800 bit/s
4: 9600 bit/s
5: 19200 bit/s
6: 38400 bit/s
7: 57600 bit/s
8: 115200 bit/s
9: 230400 bit/s
20: 300 bit/s
21: 600 bit/s
12
Local flow control (Read only)
Handles and displays used flow control on asynchronous line.
0: no flow control
3: flow control RTS / CTS
4: flow control XON / XOFF
© Stollmann Entwicklungs- und Vertriebs-GmbH
11
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
Extended Parameters 13 through 24
14
Line Feed Fill Characters
Defines, whether fill characters <NULL> should be sent following a line
feed <LF> .
Valid Parameter Values:
0
No fill characters <NULL> after a <LF>
n
Following a <LF> on the screen, append n fill characters <NULL>. n is
an integer in the range from 1 to 255.
15
Control Input Buffer Editing
Defines, whether characters in the input buffer may be edited.
Valid Parameter Values:
0
No editing; the values of the parameters 16, 17, 18, and 19 will be
ignored.
1
Editing enabled and the editing features set by the parameters 16, 17,
18, and 19 may be used; in this case, it is not possible to do a
preemptive transmission of a data packet using the Data Forwarding
Character (see parameter 4).
16
Delete Character
Defines the Character-Delete character, thus the ASCII value of the
character that when entered will delete the previously entered
character. Only possible, when parameter 15 is set to 1 (PAD has
editor capability).
Valid Parameter Values:
n
n is an integer in the range from 1 to 255 and gives the ASCII value
(decimal) of the desired Character-Delete character.
default = 8 (=> < BACKSPACE> key)
17
Delete Line
Defines the Line-Delete character, thus the ASCII value of the
character, with which you can delete the previous line. Only possible, if
parameter 15 is set to 1 (PAD has editor capability).
Valid Parameter Values:
n
n is an integer in the range from 1 to 255 and gives the ASCII value
(decimal) of the desired Line-Delete character.
default = 127 (=> <Delete> key)
12
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
18
Repeat Line
Defines the Line-Display character, thus the ASCII value of the
character, with which you can cause the characters that were entered
on the previous line to be repeated on the current line. Only possible,
if parameter 15 is set to 1 (PAD has editor capability).
Valid Parameter Values:
n
n is an integer in the range from 1 to 255 and gives the ASCII value
(decimal) of the desired Line-Display character. default = 0
19
Handling Delete Characters
Defines, what should be sent to the screen when a Character-Delete or
a Line-Delete character is received.
Valid Parameter Values:
0
Nothing
2
Send a <BS><Space><BS>, so that the last character displayed is
deleted.
20
Echo Filter
If parameter 2 is set to 1 (= character echo during data transfer), this
parameter can be used to determine which characters, entered from
the keyboard, will not be echoed to the screen.
Valid Parameter Values:
0
No echo filter, thus echo all characters
1
No echo for <CR>
2
No echo for <LF>
4
No echo for <VT>, <HT>, <FF>
8
No echo for <BEL>, <BS>
16
No echo for <ESC>, <ENQ>
32
No echo for <ACK>, <NAK>, <STX>, <SOH>, <EOT>, <ETB>, <ETX>
64
No echo for editing characters, those set with the parameters 118, 119,
and 120
128 No echo for <DEL> or any other ASCII control character not listed
above
Note: This parameter is interpreted bit wise, thus any combination of the
above listed values can be combined to form a sum of the desired values
© Stollmann Entwicklungs- und Vertriebs-GmbH
13
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
21
1.80D/09.2005
Parity handling (Read only)
Handles and displays used parity on asynchronous line.
0: no parity
1: odd parity
2: even parity
3: no parity
National Parameters 118 – 126
118
Character-Delete Character
See parameter 16.
119
Delete Line
See parameter 17.
120
Repeat Line - Line-Display Character
See parameter 18.
123
Parity handling
See parameter 21.
126
Generating a Line Feed
See parameter 13.
Note: The following parameter values are not implemented:
5, 10, 22, 121, 122, 125
Note: The following parameters are read only, can be changed using configuration
commands:
11, 12, 21
14
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Table of the X.29 standard profiles
Param Prof 0 Prof 1 Prof 2 Prof 3 Prof 4 Prof 5 Prof 6 Prof 7 Prof90 Prof91
eter
1
0
0
1
0
1
1
0
1
1
0
2
0
0
0
0
0
0
0
1
1
0
3
0
0
2
0
2
2
0
2
126
0
4
5
1
0
20
0
0
4
0
0
20
(5)
6
69
0
9
0
9
9
0
9
1
0
7
8
0
21
2
21
2
0
21
2
2
8
0
0
0
0
0
0
0
0
0
0
9
0
0
2
0
2
2
0
2
0
0
10
0
0
0
0
0
0
0
0
0
0
(11)
(12)
3
13
0
0
4
0
0
5
0
4
0
0
14
0
0
0
0
0
0
0
0
0
0
15
0
0
0
0
1
1
0
0
0
0
16
0
0
127
127
127
127
127
127
127
127
17
0
0
24
24
24
24
24
24
24
24
18
0
0
18
18
18
18
18
18
18
18
19
0
2
2
2
2
2
2
2
1
1
20
0
0
0
0
0
0
0
0
0
0
21
0
0
1
0
0
1
1
1
0
0
22
0
0
0
0
0
0
0
0
0
0
Note: Parameter in Brackets are not implemented or not setup by command profxx.
© Stollmann Entwicklungs- und Vertriebs-GmbH
15
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.2 AT command set
All parameter can be changed by using an extended AT command set described in
this chapter.
Please check if the factory setting will fit with your environment. The factory setting
is described (highlighted) in the parameter list shown in chapter "AT command set"
(see below).
If you want another configuration as set in the factory default setting, please do the
following steps:
•
•
•
•
•
•
Connect the TA+POX to ISDN interface
Connect the PC's com-port to the DTE interface of the TA+POX.
Connect the power supply to the mains socket.
Start a terminal emulation on your PC, please verify that the baudrate setting
of the terminal emulation fits those of the TA+POX.
Set up the parameter of the TA+POX from the terminal emulation and save
the parameter using the AT command set.
Example:
To change the used B channel protocol to X.75 please enter the
following commands:
ATB10<↵>
(set protocol to X.75)
AT&W<↵>
(save the new configuration)
Leave your terminal emulation and start your application program.
With the exception of the command A/ (Repeat command) all commands begin with
the prefix AT and are terminated with <↵>. Corrections in a command line are done
with <BACKSPACE>. A command line has a maximum of 80 characters (up to 140
characters using “UUS1”. The command line is automatically cancelled by longer
input. Blanks are ignored, capital/small letters are not significant.
The parameter settings of the TA+POX obtained when using the AT commands can
be permanently stored (AT&W) and are not lost by resetting or by leaving the AT
command mode.
16
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
To enter the AT command mode during an active data connection you must use the
following sequence ("Escape sequence"):
1.
<delay time of minimum 1000 ms after the last data transmittion>
2.
<+><+><+>
3.
<delay time of 1000 ms>
The time gap between all three plus signs may not exceed 1 sec.
The escape sequence is transmitted transparent to the remote device.
Note: If B channel protocol PPPasync (ATB3) is selected, the escape sequence has
to be included in an asynchronous HDLC frame. The coding of the complete
asynchronous sequence is: 7E 2B 2B 2B 1B B4 7E.
The timeout after sending the "escape sequence" <+><+><+> will increase in
terms of the configuration parameter "txfwd". The default value of "txfwd" is
set to "0" (“0” = 4 character timeout).
If "txfwd=100" (equals 1 second), the timeout of receiving the "OK" message
will be around 2 seconds.
Supported commands:
A/
Repeat last command line
This command repeats the commands of the last entered command line.
Note: No prefix AT is required.
A/
A
Accept incoming call
Using this command you can accept an incoming call, if automatic call acceptance is
not set (Register S0 = 0). An incoming call is displayed by the message “RING“ or
the code “2“.
The time interval to display the incoming call message (“RING” or “2”) can be
configured with the parameter “RINGTIMER”. The default value is set to
“RINGTIMER=50” which is equivalent to 5 seconds.
The serial status line "RI" will toggle during the active "RING" state uniformly
distributed according the half time of “RINGTIMER”.
This command must be the last command in an AT command line.
ATA[//<UUS1data>]
UUS1data
transmitted data with UUS1 signalling
© Stollmann Entwicklungs- und Vertriebs-GmbH
17
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
B
1.80D/09.2005
B channel protocol
Transmission protocol for data communication in the B channel.
ATB0 : V.110 asynchronous
ATB3 : HDLC async to sync conversion (PPP asynchronous)
ATB4 : HDLC transparent (octets are packed into HDLC frames)
ATB5 : Byte transparent voice connection (raw B channel data)
ATB10 : X.75 SLP
ATB13 : V.120 async
ATB20 : X.31 B channel (X.25 B channel)
ATB21 : X.31 D channel
ATB22 : T.70NL
ATB23 : T.90NL
ATB31 : MLPPP
ATB40 : B channel transparently switched to IOM-2
%B
Set local baudrate
Sets the local baudrate of the TA to the desired value (fix value) or to auto
detection. When auto detection is set, the TA will recognize the desired baudrate
with every newly entered AT command by the terminal equipment (PC). With all
other settings the PC must use the same baudrate.
Must be the last command in an AT command line.
AT%B0
Automatic local baudrate detection enabled, (default)
autobauding exclude serial speed of 300bps, 600bps)
AT%B1
Local baudrate set to 1200 bit/s
AT%B2
Local baudrate set to 2400 bit/s
AT%B3
Local baudrate set to 4800 bit/s
AT%B4
Local baudrate set to 9600 bit/s
AT%B5
Local baudrate set to 19200 bit/s
AT%B6
Local baudrate set to 38400 bit/s
AT%B7
Local baudrate set to 57600 bit/s
AT%B8
Local baudrate set to 115200 bit/s
AT%B9
Local baudrate set to 230400 bit/s
AT%B20
Local baudrate set to 300 bit/s (no autobauding detection)
AT%B21
Local baudrate set to 600 bit/s (no autobauding detection)
Note: If autobauding is selected (default) and no AT command is entered after
power on of the TA+POX, a response from the TA (i.e. RING) will be sent with
the baudrate of 115200 bit/s.
18
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
CONF
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Enter TA+Configurator
Enters directly into the TA+Configurator, the configuration prompt "#" will be
displayed. Leave the TA+Configurator with the command "quit" (or “exit” or “go”).
ATCONF
Note: During the change between the command sets from "AT command set" to
"configuration command set" the serial status line DSR gets inactive.
&C
DCD control
Selects the behavior of the DCD control line from the TA.
AT&C
TA control line DCD is always ON
AT&C1
DCD ON indicates ISDN connection is established and
synchronized (default)
AT&C2
TA control line DCD follows DTR
For nearer information see also chapter 3.3.
#C
Received bearer service
Shows the bearer service that is received with an incoming call in hexadecimal
coding hbhb.
The value for hbhb (word) is the CIP value as defined in the CAPI 2.0 specification,
also to be found via Stollmann URL http:\\www.stollmann.de.
AT#C
#C1=hbhb
Select bearer service outgoing
Selects the bearer service that will be sent with an outgoing call
The value for hbhb (word) is the CIP value as defined in the CAPI 2.0 specification
(default 0000).
Example: an outgoing call as a voice call: AT#C1=0004.
Example: an outgoing call as a data call: AT#C1=0002.
© Stollmann Entwicklungs- und Vertriebs-GmbH
19
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
#C2=hbhbhbhb
1.80D/09.2005
Select bearer service incoming
Selects the bearer services that can be accepted with an incoming call. The
definition of hbhbhbhb (double word) is the CIP mask as defined in the CAPI 2.0
specification (default 00000004).
Example:
AT#C2=00030012 : Accept analogue incoming calls
AT#C2=00000001 : Accept all incoming calls.
Note: Before issuing an outgoing call the command AT#C1 has to be set.
To use the predefined services please setup factory defaults (AT&F).
D
Initiate outgoing call
Dials the number (D for Dial). The dial modifier "W", ">", "T", ";", "@" can be freely
inserted in the dial string; they have no influence on the dial procedure of the
TA+POX.
Must be the last command in AT command line.
Any character input while the TA is dialing will cancel the dialing procedure.
ATD<CALLEDnumber>[/<subaddr>][//<UUS1data>]
[X [Pxxx-][R,][N<nuipwd>,][G<cug>,]<X25number>][D<userdata>]]
CALLEDnumber: ISDN call number for a dialed B channel connection or
X.25 number for X.31 D channel
subaddr
dialed sub address
UUS1data transmitted data with UUS1 signaling
X:
starting X.25 parameter section
P:
use packet size xxx for X.25 connection
R:
request the facility reverse charging
G:
access to X.25 closed user group
O:
Outgoing call from X.25 closed user group
N:
use NUI and password with call setup
allowed chars: a-z, A-Z, 0-9.
(overrides setting of nui configuration command)
X25number: dialed X.25 call number (X.25 B channel only)
D:
separator for user data:
"D" or ",": user data without protocol ID
"P": user data include protocol ID (“01000000“)
ATDL
Dial the last dialed number
ATDS=n
Dial number n from stored telephone number list (n = 1..3)
(See command AT&Z to store numbers)
ATD<CALLEDnumber>e Make a call for remote management (see note).
20
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Examples (X.25/X.31):
ATD12345678
X.31: dial X.25 number 12345678
X.25-B: dial X.25 number 12345678
after ISDN call to 12345678
ATD12345678X4000123456
X.25-B:
dial
X.25
number
4000123456 after ISDN call to
12345678
ATD12345678X4000123456Ddatadata X.25-B:
dial
X.25
number
4000123456 after ISDN call to
12345678 with X.25 user data
“datadata”.
Notes:To setup the own sub address see configuration command sub.
Adding an "e" to CALLEDnumber indicates that a connection to the internal
remote access of a TA+POX shall be performed, the protocol X.75 (ATB10)
has to be setup before use.
&D
DTR control
Selects the behavior of the TA, when the DTE control line DTR changes from ON to
OFF.
AT&D
DTE control line DTR setting is ignored
AT&D2
DTE control line DTR is evaluated: dropping the DTR line by the
DTE will disconnect an existing ISDN connection (default).
An incoming call will accepted only with DTR active.
AT&D4
DTE control line DTR is evaluated: dropping the DTR line by the
DTE will disconnect an existing ISDN connection.
An incoming call will accepted with DTR off.
For nearer information see also chapter 3.3.
E
Local echo
Selects the local echo in command mode.
ATE
No local echo
ATE1
Local echo on in command phase (default)
&F
Load factory defaults
Factory default will be loaded, ISDN protocol settings, passwords and msn's will not
be overwritten. (for storing in non volatile memory please use the command AT&W).
AT&F
setup all parameter concerning data port.
© Stollmann Entwicklungs- und Vertriebs-GmbH
21
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
AT&F1
H
1.80D/09.2005
setup all parameter including ISDN protocols, msn settings and
passwords (ISDN, IINIT, PTP,FTEI, PROT, MSN, RPWD )
Disconnect
Disconnects existing ISDN data connection, after issuing the escape sequence (see
page 16).
ATH[//<UUS1data>]
UUS1data
transmitted data with UUS1 signaling
To enter the AT command mode during an active data connection you must use the
following sequence ("Escape sequence"):
1.
<delay time of minimum 1000 ms after the last data transmittion>
2.
<+><+><+>
3.
<delay time of 1000 ms>
The time gap between all three plus signs may not exceed 1 sec.
The escape sequence is transmitted transparent to the remote device.
The timeout after sending the "escape sequence" <+><+><+> will increase if
the configuration parameter "txfwd" will rise. The default value of "txfwd" is set
to "0".
I
Display version information
Displays different information about version number and settings:
ATI Returns the "Modem" type; name of the terminal adapter (“TA+POX“)
ATI1 Returns internal checksum (“64“)
ATI2 Returns “OK“
ATI3 Returns version string: "V1.xyz"
ATI4 Returns manufacturers name: "Stollmann E+V GmbH"
ATI5 Returns ISDN selected protocol: "0 - DSS1"
ATI6 Returns copyright string: "(c) Copyright Stollmann GmbH"
ATI7 Returns “OK“
ATI8 Returns “ERROR”
ATI9 Returns plug and play ID string
ATI77 Returns Bootloader version string
ATI99 Returns software creation date
22
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
&K
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Flow control
Selects the flow control behavior of the TA while in data communication phase.
AT&K
No local flow control between the DTE and TA is used
AT&K3
Local flow control is set to hardware handshake RTS/CTS
AT&K4
Local flow control is set to software handshake XON/XOFF
For nearer information see also chapter 3.3.
#M
Received CLID
Shows the called line identification (CLID) that is received with an incoming call –
this is the number of the called party addressed on the local S-bus (selected msn).
AT#M
N
Set line baudrate V.110
Selects the line baudrate of the TA to the desired value (only valid for B channel
protocol V.110 asynchronous).
ATN0 Line baudrate automatic set (equals to local baudrate or less)
ATN1 Line baudrate set to 1200 bit/s
ATN2 Line baudrate set to 2400 bit/s
ATN3 Line baudrate set to 4800 bit/s
ATN4 Line baudrate set to 9600 bit/s
ATN5 Line baudrate set to 19200 bit/s
O
Return to online state
If the TA+POX is in command mode after issuing an escape sequence out of an
existing connection, ATO brings the TA+POX back to data phase.
Must be the last command in AT command line.
ATO
#O
Received CLIP
Shows the calling line identification (CLIP) that is received with an incoming call –
number of the calling party.
AT#O
© Stollmann Entwicklungs- und Vertriebs-GmbH
23
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Q
1.80D/09.2005
Suppress results
With this command result codes or messages can be suppressed.
ATQ
Returns status codes after command input (default)
ATQ1
No result codes are returned
&R
CTS control
Selects the behavior of the CTS control line from the TA.
AT&R
TA control line CTS is following all changes of RTS
AT&R1
CTS is ON and handle serial flow control RTS/CTS (default)
AT&R2
TA control line CTS is following all changes of DTR
For nearer information see also chapter 3.3.
S
Display and set internal S register
ATSnn?
Show actual values (decimal) of selected register nn
ATSnn=xxx Set selected register nn to the decimal value xxx.
&S
DSR control
Selects the behavior of the DSR control line from the TA.
AT&S
TA control line DSR is always ON (default)
AT&S1
DSR ON indicates ISDN connection is established and
synchronized
AT&S2
TA control line DSR is following all changes of DTR
For nearer information see also chapter 3.3.
V
Result format
ATV
ATV1
&V
Display configuration
AT&V
AT&V1
24
Result is presented as numbers (followed by <↵>)
Result is presented as text (default)
Displays the current configuration of AT command setting
including stored ISDN numbers
Displays the current configuration of extended AT command
setting
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
W
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Extended result codes
ATW
ATW1
Result is presented without extended result codes
Result is presented with extended result codes
• RING and CONNECT including ISDN address (CLIP),
• error causes
• Message RINGING will be displayed with an outgoing call
• UUS1 data will be displayed
Note: see also chapter 3.2.3 “AT result codes”
&W
Store active configuration
The current configuration will be stored in non volatile memory.
AT&W
X
Reduce result messages
Reduces the number of result messages after trying to set up a connection
ATX0 "CONNECT" only (without line speed)
ATX1 "CONNECT" with line speed, "BUSY", "NO DIALTONE" not used
ATX2 "CONNECT" with line speed, "BUSY" not used
ATX3 "CONNECT" with line speed, "NO DIALTONE" not used
ATX4 "CONNECT" with line speed, all messages used (default).
Z
Load stored settings
The stored configuration from the non volatile memory will be load as current
configuration parameter set.
Must be the last command in an AT command line.
ATZ
#Z
Define own msn
(compatibility to older firmware)
Defines the msn nn (multiple subscriber number) for the data port.
If the number is set to “*“ (default), all incoming calls are acceptable.
The msn can be displayed by command AT&V.
AT#Z=nn
set parameter "msn to nn
© Stollmann Entwicklungs- und Vertriebs-GmbH
25
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
Note: If 1TR6 D channel protocol is selected, only one (the last digit) will be used
for the “EAZ” (Endgeräte Auswahl Ziffer) selection.
This parameter is not saved automatically.
**DBITS
Number of data bits x asynchronous chars (7,8)
Number of data bits x for asynchronous character (7,default: 8)
AT**DBITS=x
**PRTY
Set parity of asynchronous characters
Selects the parity for asynchronous characters.
0: no parity; 1: even parity; 2: odd parity
AT**PRTY=0
No parity (default)
AT**PRTY=1
Odd parity
AT**PRTY=2
Even parity
Note: To use other data formats than 10 bit (8N1, 7E1, 7O1) you have to set
parameter “br” (serial baudrate) to a fixed speed.
3.2.1 ISDN specific AT commands
Setting up special ISDN parameter:
(only one command is allowed per AT command)
Note: All AT** commands has to be sent at the end of the command line.
**BSIZE
Set B channel block size
Defines the maximum length x of a data block transmitted or received in B channel.
This parameter value depends of the configured B-channel protocol.
• prot=10
BSIZE = 2048
• prot=13
BSIZE = 259
• prot=20
BSIZE = 128
• prot=21
BSIZE = 128
AT**BSIZE=x
Note: The value “BSIZE” will be changed by setting the B channel protocol (ATBx)
automatically.
26
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
**BC
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Set bearer capatibility (BC)
Defines the BC value for outgoing calls in hexadecimal format. In some situation a
specific BC value is required to pass detailed information about the used B channel
protocol to the called party. This can be done by setting the BC to a fix value.
An empty parameter has to be entered by "-" (default: BC is empty).
Example:
Deleting of BC-value:
AT**BC=-<↵>
Entering a new BC:
AT**BC=8890<↵>
Note: The value will be changed by setting the B channel protocol (ATBx).
**LLC
Set low layer compatibility (LLC)
Defines the LLC value for outgoing calls in hexadecimal format. In some situation a
specific LLC value is required to pass detailed information about the used B channel
protocol to the called party. This can be done by setting the LLC to a fix value.
An empty parameter has to be entered by "-" (default: LLC is empty).
Example:
Deleting of LLC-value:
AT**LLC=-<↵>
Entering a new LLC:
AT**LLC=8890<↵>
Note: The value will be changed by setting the B channel protocol (ATBx).
**HLC
Set higher layer compatibility (LLC)
Defines the HLC value for outgoing calls in hexadecimal format. In some situation a
specific HLC value is required to pass detailed information about the used B
channel protocol to the called party. This can be done by setting the HLC to a fix
value.
An empty parameter has to be entered by "-" (default: HLC is empty).
Example:
Deleting of HLC-value:
AT**HLC=-<↵>
Entering a new HLC:
AT**HLC=8090A3<↵>
Note: The value will be changed by setting the B channel protocol (ATBx).
**DTE
Set B channel Layer 2 address
Selects the Layer 2 link addresses. Only valid for X.75, LAP-B and X.25-B protocol.
AT**DTE=0 calling side reacts as DTE,
called side reacts as DCE (default, X.75 standard)
AT**DTE=1 TA reacts as DTE (own cmd.-adr. = 01)
AT**DTE=3 TA reacts as DCE (own cmd.-adr. = 03)
Note: The value “DTE” will be changed by setting the B channel protocol (ATBx)
automatically.
© Stollmann Entwicklungs- und Vertriebs-GmbH
27
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
**ISDN
1.80D/09.2005
Select D channel protocol
Selects ISDN D channel protocol to the ISDN line. The protocol must fit the protocol
running on the ISDN line otherwise a connection cannot be set up.
Note: after changing and storing the ISDN protocol the TA has to be reset by
powering it off and on (alternately you can use the command
AT&W**RESET).
AT**ISDN=0
Select DSS1 (Euro-ISDN) (default)
AT**ISDN=1
Select 1TR6 (Germany national)
AT**ISDN=5
Select Bellcore National ISDN-1/2 (USA)
(Option)
AT**ISDN=6
Select NTT INS-NET (Japan)
(Option)
AT**ISDN=7
Select AT&T 5ESS (USA)
(Option)
AT**ISDN=8
Select VN-4 (France)
(Option)
AT**ISDN
Show selected ISDN protocol
AT**?ISDN
Show available ISDN protocols
**K
Set Layer 2 window size
Sets window size x layer 2 protocol B channel: x = 1 ..7, default: 7
AT**k=x
The default value is dependent of the selected B channel protocol.
**RPWD
Password remote configuration
Sets password for remote configuration to nn (1..32 chars)
AT**RPWD=nn
Default: empty, just press return key.
**SPID1, SPID2
Set SPID
(Option)
For ISDN lines in the U.S. you have to set the SPID. You get it from your ISDN
provider.
AT**SPID1=xxx
Set SPID 1
AT**SPID2=xxx
Set SPID 2
28
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
**STATUS
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Show status of voice port
The overall status of the TA will be displayed.
Example:
"at**status"
Current status information TA+POX
serial line: DTR:on, RTS:on, DSR:on, CTS:on, DCD:on, RI:off
ISDN: L1:up
Dch: Prot:DSS1, State:connected, CdPN:291, CgPN:509, prev error: 0
Bch: Prot:X.75 SLP, State:connected, CdPN:291, CgPN:509
**<cmd>
Execute configuration command
Executes one configuration command, for definition of commands see page 50.
AT**<cmd>
Note: All AT** commands has to be sent at the end of the command line.
© Stollmann Entwicklungs- und Vertriebs-GmbH
29
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.2.2 AT command S register set
S0
S1
S2
S3
S4
S5
S6
S7
S9
S10
S16
S90
S91
0: No automatic call acceptance, acceptance of an incoming call is
controlled by the data terminal (command ATA after RING)
1: Immediate call acceptance by the terminal adapter
2..n: Call acceptance through the terminal adapter after n "RING"
messages.
The time interval to display the incoming call (“RING” or “2”) can be
configured with parameter “RINGTIMER”.
The serial status line "RI" will toggle during the active "RING" state
uniformly distributed according the half time of “RINGTIMER”.
Ring Counter, increase RING count if S0 not equals 0 (read only)
Escape Character (default = 43h)
Carriage Return Character (default = 13)
Line Feed Character (default = 10)
Backspace Character (default = 08)
Timer before dialing (default=3) This timer is not supported.
Wait time for Carrier (sec) (default = 30 sec)
Enable PNP functionality for Windows95 (default=0, disabled)
See also internal configuration command "PNP"
delay time in seconds to send out the existent serial data to the serial
port after the active ISDN data connection is cleared.
When the timer expired the serial data buffer will be cleared.
Last occurred CAPI/ISDN error cause
Last incoming ISDN calling number (CLIP)
0: default
1: all unknown AT commands will be answered with OK.
2: Windows 2000 compatibility: some AT commands will be answered
with OK (see list below), unknown AT commands will be answered with
OK.
Windows2000 AT command set change:
ATNxxx
all commands ATNxxx will respond OK without any
functionality behind it. V.110 baudrates can be set
with AT**BRN.
ATBxxx
All commands ATBxxx will respond OK without any
functionality behind it. The B-channel protocol
settings can be set with AT**PROT.
AT\Nxxx
All commands AT\Nxxx will respond OK without
any functionality behind it. The B-channel protocol
settings can be set with AT**PROT.
30
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
3.2.3 AT result codes
Result codes (numerical and verbose):
Code
Text
Meaning
0
OK
Command completed
1
CONNECT <rn>
Connection established
(rn = call number of remote site)
2
RING <rn>
Indicates an incoming call (SETUP received)
3
NO CARRIER <xx>
No synchronization (xx = ISDN error cause)
4
ERROR
Illegal command or error that can not be
indicated otherwise
5
CONNECT 1200 <rn>
Connection, line speed 1.2 kbps (V.110)
6
NO DIALTONE <xx>
No access to ISDN network (xx = ISDN error)
7
BUSY <xx>
Number engaged (xx = ISDN error cause)
8
NO ANSWER <xx>
No connection; called number can not be
reached (xx = ISDN error cause)
9
RINGING <rn>
Outgoing call is ringing at called site
10
CONNECT 2400 <rn>
Connection, line speed 2.4 kbps (V.110)
11
CONNECT 4800 <rn>
Connection, line speed 4.8 kbps (V.110)
12
CONNECT 9600 <rn>
Connection, line speed 9.6 kbps (V.110)
16
CONNECT 19200 <rn> Connection, line speed 19.2 kbps (V.110)
19
CONNECT 64000 <rn> Connection, line speed 64 kbps
Call number display:
<rn> = call number of remote site
In AT command mode, call number display (does not belong to the standard AT
command set) can be turned on by issuing the command ATW1. If turned on, the
call number of the caller is shown with the CONNECT or RING message (in pointed
brackets), depending on the signaling in the D channel.
If the TA is used at the public network then the call number of the remote site
(including area code) is displayed.
Example:
TxD
ATW1
RxD
OK
RING <040890880>
ATA
CONNECT 64000 <040890880>
© Stollmann Entwicklungs- und Vertriebs-GmbH
31
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
Error cause display:
<xx> = ISDN release (error) cause, hexadecimal
Example:
Tx data
ATW1
Rx data
OK
ATD12345
NO CARRIER <34A2>
In AT command mode, error cause display (does not belong to the AT command
standard) can be turned on by issuing the command ATW1. The shown error
causes use the coding defined by the CAPI definition. ISDN error causes from the
ISDN network are always coded as 34xxH, where xx represents the hexadecimal
version of the ISDN error cause (see page 78). All other causes are CAPI error
causes (see page 86).
Note: If autobauding is selected and after powering on the TA no AT command is
entered, a response from the TA (i.e. RING) will be sent with the baudrate
115200 bit/s.
UUS1 data display: (see also chapter 3.7)
In AT command mode, UUS1 data (user to user data) can be turned on by issuing
the command ATW1. If turned on, the incoming UUS1 data are shown with the
CONNECT or RING message after the [//] chracters, depending on the signaling in
the D channel.
Example:
Tx data
ATW1
Rx data
OK
RING <//UUS1_testdata>
32
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
3.3 Serial status lines
The behave of the output serial status lines DSR, CTS, DCD, RI and the input serial
status lines DTR, RTS can be configured as described in chapter 3.2 and 4.1 to 4.3.
After power on all serial status lines from the TA will be inactive.
The serial status line DSR can be configured to signal the activation of the current
command set (cdsr=0). When changing the command set (cmds) the DSR line goes
off during this change phase.
The serial input status lines DTR and RTS will be controlled of an interrupt in the TA
firmware. With regard of this behave the maximum input level change must be lower
than 100Hz (10ms steps).
The V.24 control circuits will be described for the three different states:
no connect phase: The TA has no ISDN connection.
The serial data (commands and responses) will be used to
configure the TA (command mode).
dial phase:
The TA has started to establish an ISDN connection and is
and
waiting for the synchronization.
disconnect phase: The TA disconnects the existing connection (B-channel and Dchannel connection).
connect phase:
ISDN data connection is established (D-channel and B-channel
connected).
Serial data will be sent or received according to the configured
B-channel protocol (data mode).
Status line Description
0 : CTS follows RTS
CTS
1 : ON, HW FLC
2 : CTS follows DTR
0 : DCD always ON
DCD
1 : DCD indicates a connection
2 : DCD follows DTR
0 : DSR always ON
DSR
1 : DSR indicates a connection
2 : DSR follows DTR
flc.*
flc.**
no connect dial/disc.
=RTS/flc.* =RTS/flc.*
ON/flc.*
ON/flc.*
=DTR/flc.* =DTR/flc.*
ON
ON
OFF
OFF
=DTR
=DTR
ON
ON
OFF
OFF
=DTR
=DTR
connect
=RTS/flc.**
ON/flc.**
=DTR/flc.**
ON
ON
=DTR
ON
ON
=DTR
CTS signals the serial flow control from TA (DCE) to the DTE in the command mode and data
mode (flc=5).
CTS signals the serial flow control from TA (DCE) to the DTE in the flow control modes 3 or 5
(flc=3 or flc=5).
© Stollmann Entwicklungs- und Vertriebs-GmbH
33
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
DTR: Data terminal ready
The serial status line DTR is used to control the ISDN connection.
0:
No control
Outgoing calls:
The DTR level will be ignored to establish a connection.
Incoming calls:
Incoming calls will be accepted independent of DTR status.
Disconnection:
DTR drop does not disconnect an active connection.
2:
DTR line will be considered
Outgoing calls:
The DTR level will be considered.
DTR off in the command mode refuses the call procedure
with ERROR.
Incoming calls:
Incoming calls will be accepted only when DTR is ON.
The incoming call request can be refused with changing
DTR to off.
Disconnection:
DTR drop disconnects an active connection
or a call during the dial phase.
If DTR will be dropped immediately after sending serial
data there is no guarantee to transmit these data to the
destination side.
A delay of (configured "txfwd" time + 10ms) between
sending the last data byte and dropping the DTR line would
send out the last data stream.
4:
DTR ignore and DTR drop disconnects
Outgoing calls:
The DTR level will be ignored to establish a connection.
Incoming calls:
Incoming calls will be accepted independent of DTR status.
Disconnection:
DTR drop disconnects an active connection.
If DTR will be dropped immediately after sending serial
data there is no guarantee to transmit these data to the
destination side.
A delay of (configured "txfwd" time + 10ms) between
sending the last data byte and dropping the DTR line would
send out the last data stream.
34
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
RTS: Request to send (flow control)
This serial status line is used for the flow control between the DTE device and the
TA (DCE).
0:
No flowcontrol
3:
Hardware flowcontrol RTS/CTS in the data mode
•
If the DTE activates the flow control (RTS=off) the TA needs up to 3 character to
stop the serial data stream to the DTE.
•
If the connection will be cleared during an active flow control (RTS=off) the
received data will be sent to the DTE device when RTS gets active. The reported
result code will also be sent with RTS on.
The control lines to indicate the active connection (DCD) will be changed without
recognizing the current flow control state.
CTS: Clear to send (flow control)
This serial status line is used for the flow control between the TA (DCE) and the
DTE device.
0:
No flowcontrol
3:
Hardware flowcontrol RTS/CTS in the data mode
•
•
If the TA activates the flow control (CTS=off) the TA will buffer up to 256 bytes
from the DTE device.
If the connection will be cleared with DTR=off during an active flow control
CTS=off) the current connection will be cleared after a short timeout.
The received serial data from the DTE during the connection will be erased after
clearing the connection.
The control lines to indicate the active connection (DCD) will be changed without
recognizing the current flow control state.
RI:
Ring indicator
The serial status line RI gets active during an incoming call request.
If the incoming call will be accepted or the call request ended the RI control circuit
gets off.
© Stollmann Entwicklungs- und Vertriebs-GmbH
35
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.4 Automatic call establishment
Automatic call establishment is available in the following modes:
• An automatic call will be initiated when the control line DTR is on
• An automatic call will be initiated when serial transmit data (character) received
into the terminal adapter
• Automatic connection establishment independent of any status line.
To enable automatic call you have to set TA+configuration parameter cmds to 6, 7
rsp. 8 (see below). With changing this parameter the baudrate has be set to a fixed
value (‘br’ not equal to ‘0’).
An established connection will be indicated by a status line. See also configurations
commands cdcd and cdtr.
If a connection cannot be established successfully an automatic retry will be started.
The duration of trying to establish the connection and the pause for next retry can
be configured.
The dialed numbers are taken from the table catab, all numbers from the call table
catab will be taken one after each other.
cmds 6
cmds 7
Automatic connection establishment when DTR is ON.
Automatic connection establishment when the TA receives any
data byte.
cmds 8
Automatic connection establishment independent of any status
line.
Note: (autobauding is not supported, set br not equal to 0)
cato n
capa n
catry n
call abort of a not successful call after n seconds.
n={3..255}, default: 15 seconds.
call pause for n seconds before next call attempt.
n = 0 : immediate call retry. n={0..255}, default: 3 seconds.
automatic call: max. no of tries of every number entry in catab.
n={1..255}; default: 1
catabx nn/ss set entry number x to ISDNnumber nn and subaddress ss
catabx clear entry number x
catabx
show entry number x
catab
Show all entries
Maximum number of entries = 3; x = 1..3
Maximum length of ISDN number = 20 digits
Maximum length of subaddress = 20 digits
36
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Hint: The configuration command „idle“ can be used, to automatically disconnect
after a predefined time without data transmission.
Note: Please take care that parameter rsttim is greater than 10
(RSTTIM, reset timer; default value = 40, 2 sec)
and rstmsg=1 (reset message)
to enable the entry into the TA+Configurator after reset.
© Stollmann Entwicklungs- und Vertriebs-GmbH
37
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.5 ISDN access control, security callback, leased line
3.5.1 ISDN access control
Using these commands you can setup a table, to allow only dedicated callers to get
a connection to the TA.
If this list is empty (default) or one entry is set to star (*), any incoming call is
allowed.
Every incoming call that does not fit to one of the entries of acctab will be ignored.
The received calling party number is compared to every entry beginning at the last
digit and is stopped when the shorter number is completely compared.
acctabx nn/ss set entry number x to ISDN number nn and subaddress ss
acctabx clear entry number x
acctabx *
Allow all incoming calls to be accepted
acctabx
show entry number x
acctab
Show all entries
Maximum number of entries = 5; x = 1..5
Maximum length of ISDN number = 20 digits
Maximum length of subaddress = 20 digits
The ISDN number nn can contain wildcards:
* : represents one or more digits
? : represents exactly one digit
Note: If a subaddress is set, the received calling subaddress must be identical to
the subaddress that is set.
Examples:
acctab1 1234567890
acctab2 *456*
acctab3 ?2345678??
acctab2 *1234/987
acctab3 *
acctab3 -
accept only specified number
accept all numbers with 456 somewhere in the
middle
accept all number with 2345678 in the middle
preceded by one digit and followed by two digits.
accept all numbers that end with 1234 and have
the subaddress 987
accept all incoming calls without subaddress
clear entry no. 3
Note:
If you are not sure, in which format the calling number will be presented with
an incoming call, please use the command ATW1 to see the format of the
calling number in the RING message. This number can be entered into the
acctab.
38
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
3.5.2 Security callback
With the security callback function you can initiate the called TA+POX to make an
automatic call to a predefined ISDN number.
The callback has to be enabled or disabled by using the command
"cmds2=40" Security callback enabled
"cmds2=0" Security callback disabled
If security callback is enabled and the calling number of an incoming calls fit's to
one entry of the acctab the called TA+POX will automatically try to establish a
connection using the entry in the casnr.
The incoming call will not be accepted and cause no RING message, the incoming
call will immediately and automatically rejected.
The automatic callback will be started after a delay as defined by the parameter
capa.
Only one automatic callback will be initiated by TA+POX.
There is no restriction in using the different command modes for the TA+POX that
has security callback enabled (i.e. AT dialing or automatic call DTR).
3.5.3 ISDN leased line (option)
To use the TA+POX with a leased line you have to setup the ISDN protocol to one
of the following values:
isdn=12
isdn=13
isdn=14
leased line with usage of just B channel B1
leased line with usage of just B channel B2
leased line with usage of both B channels.
With setting the ISDN protocol to leased line, no D channel protocol is used. A
connection will be established by dialing any number, if the activation of the leased
line access is available (LED1 is ON).
Note: to achieve data communication you should use one of the protocols async
HDLC or HDLC transparent.
© Stollmann Entwicklungs- und Vertriebs-GmbH
39
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.6 B channel connections with external IOM use (option)
You can use the TA+POX with external devices connected to the B channel instead
of using the on board existing B channel hardware.
The B channel data have to be interfaced through the IOM interface.
The local devices are disabled by using the B channel protocol "prot=40" (external).
A connection can be setup by using the standard call control command sets like
ATD-command, automatic… (see setting of cmds).
For enhanced control of the B channel connections (i.e. voice connections, hold
line, …) the corresponding command set is described in the manual TA+HIT,
section external IOM interfacing.
Note: please make sure, that the module TA+HUT has the correct Bootloader
version, please verify with your supplier.
Example: BOOT LOADER V1.18 230200 030E-26-00.
The <26> is a hardware sub type, must be <26> or <36> on TA+HUT
(4Mbit / 8Mbit) for include external IOM enabled.
3.7 User to User Signaling UUS1
With outgoing and incoming calls the transmission of User-to-User-Data (UUS1data) can be performed using the ISDN supplementary service UUS1. The UUS1data are transmitted transparently from the calling party to the called party before
the B channel connection is fully established.
Please note, that this ISDN service typically has to be enabled by the ISDN service
provider and may be charged additionally.
See the command ATD in AT command set:
Example:
ATDisdnnumber[//<UUS1-data>]
(PAD:)
X25number[I<ISDNnumber>[//<UUS1data>]]
“//”: separator for UUS1-data
The UUS1-data have a maximum length of 128 Bytes and will be interpreted as
ASCII characters.
Incoming UUS1-data are presented as enhancement to the RING and CONNECT
message.
AT: RING [<rn>] [//<UUS1-data>]
CONNECT [<rn>] [//<UUS1-data>]
PAD: <X.25addr>I<isdnnumber>[//<UUS1-data>]
COM
40
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
Note: The presentation of UUS1-data has to be enabled by command ATW1.
The data are presented as ASCII characters.
An incoming call can be accepted (S0 register set to 0) by an ATA or rejected by an
ATH combined with the transmission of UUS1-data (AT only):
ATA [//<UUS1-data>]
ATH [//<UUS1-data>]
Examples:
ATD1234567890//userdata#010203*end
RING //userdata
RING //#01020304
3.8 Subaddressing
With outgoing and incoming calls the transmission of subaddresses can be
performed using the ISDN supplementary service SUB. The subaddress is
transmitted transparently from the calling party to the called party before the B
channel connection is fully established.
Please note, that this ISDN service typically has to be enabled by the ISDN service
provider and may be charged additionally.
The subaddress is separated by an “/“ from the called number.
The functionality Subaddressing can be used with the dialing procedures ATcommand set, PAD X.3 and automatic call.
Examples:
ATDisdnnumber[/subaddr]
isdnnumber
Dialing called party number
subaddr
Called subaddress
RING [<rn>[/subaddr]]
CONNECT [<rn>[/subaddr]]
rn
subaddr
Calling party number
Calling party subaddress
The own subaddress (calling subaddress) can be setup using the configuration
command sub.
Note: The subaddress can be entered additionally into all tables that contain ISDN
numbers for dialing or checking an ISDN address.
© Stollmann Entwicklungs- und Vertriebs-GmbH
41
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.9 X.25 address translation table
If the protocol X.25 B channel (prot = 20) is selected, then with every outgoing X.25
call the ISDN number will be taken out of the corresponding entry in the table xtab.
If no entry is found the X.25 address will be used as the ISDN number.
When an ISDN number is setup in the dialing command string with AT commands or
PAD X.3 commands, the xtab entries will not be used.
If an ISDN number is setup using the command dad, the table xtab will not be used.
xtabx <xadr>i<nn/ss>
xtabx xtabx
xtab
set entry number x to ISDNnumber nn/ss and X.25
address xadr.
xadr: To find an entry, the x25addr is compared against all
entries of xadr. The xadr can contain wildcards:
*:
represents one or more digits
?:
represents exactly one digit
nn/ss: the used ISDNnumber contains the number plus
subaddress, the subaddress can be empty.
nn = ISDN number, ss = subaddress
The ISDNnumber nn can contain following wildcards:
?:
represents exactly one digit, only allowed at the
end of the number. The value is taken from the
corresponding digits of the xadr.
clear entry number x
show entry number x
Show all entries
Maximum number of entries = 5; x = 1..5
Maximum length of ISDN number = 20 digits
Maximum length of subaddress = 20 digits
Note:
The table is valid for X.25 in B channel and X.31D rerouting only.
Examples:
xtab1 45400029003i04089928392
42
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
3.10 X.25 D channel rerouting
If the protocol X.25 D channel (prot = 21) is selected an automatic establishment of
a B channel connection can be selected, if the X.25 call using the X.31-D channel is
not successful.
The B channel connection will be started if
• no successful X.25 connection is established within of a timeout set by command
"cato" in seconds
• an error is reported from X.31 D channel line.
The rerouting will be activated by setting the configuration command "x31rr=1" (from
PAD enter please "exec x31rr=1").
The ISDN number used for establishment of the B channel connection will be taken
from the table xtab dependent of the entry found in the table.
If the X.25 address meets no entry, the rerouting will not be used.
Example:
1. To enable rerouting for all X25 addresses:
x31rr 1
xtab1 *i04089928392
2. To enable rerouting for the x25 address 45400012345 and 45400012389:
x31rr 1
xtab1 45400012345i04089928392
xtab2 45400012389i04089928392
or
xtab1 454000123*i04089928392
or
xtab1 454000123??i04089928392
© Stollmann Entwicklungs- und Vertriebs-GmbH
43
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
1.80D/09.2005
3.11 Using Multilink PPP
To enable Multilink PPP handling within the TA please enable protocol ML-PPP:
ATB31 rsp. prot = 31.
ML-PPP may be used with two different authentication protocols during the link
establishment phase:
• PAP (password authentication protocol, RFC 1334),
• CHAP (challenge handshake authentication protocol, RFC 1994) with variants
• MD5 according to RFC 1321,
• Microsoft Chap according to RFC 2433.
The simpler PAP transmits the user password as clear text over the line, whereas
CHAP uses encryption. Which protocol is actually used depends on
•
•
the local PC: if the dialup network configuration requests password encryption
only CHAP will be used,
the remote host configuration: it may (e.g.) allow both PAP and CHAP, CHAP
only etc..
3.11.1 Restrictions on Windows95
The CHAP protocol requires that the local side (PC or TA) responds with the proper,
encrypted password when ever requested by the remote host. Since Windows95
does not respond on repeated requests CHAP can be used on the second link only
if the TA knows the password. It must be stored in the TA’s NVRAM:
•
•
Enter “at**chappwd=<password>” to input your password in the TA.
Warning: The input echo is shown in clear text, it should be hidden from
unauthorized persons. Nevertheless, commands as “AT&V1” display the
password as a sequence of asterisks (“*”).
Enter “AT&W” to store the setting in the TA.
If the password chappwd is not stored on the TA (or is wrong) and remote and/or
local dialup network configuration require password encryption, the second link will
be physically established for a short time, and will then be disconnected. As a
consequence the Multilink option is disabled for the current connection.
44
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
3. Using the TA+POX
3.11.2 Bandwidth on demand ("BOD")
Enabling this feature will cause the TA+POX to use the Multilink PPP protocol to
enhance the ISDN throughput using the second B channel automatically:
• if the throughput of the internet connection is higher than a definable value a
second B channel connection will be established automatically and used for data
transfer.
• if the throughput of the internet connection is lower than a definable value the
second B channel connection will be disconnected automatically.
at**bod=0
at**bod=1
at**bodiv=<incrValue>
at**bodit=<incrTime>
at**boddv=<decrValue>
at**boddt=<decrTime>
disable BOD (default)
enable BOD
Throughput level to add 2nd B channel connection
(in kbit/s) (default=40)
duration that bodiv has been reached to add 2nd b
channel (in secs) (default=30)
Throughput level to release 2nd B channel
connection (in kbit/s) (default=40)
duration that boddv has been reached to release
2nd b channel (in secs) (default=30)
Note: call bumping ("cmlp") has higher priority than bandwidth on demand.
© Stollmann Entwicklungs- und Vertriebs-GmbH
45
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
1.80D/09.2005
4 TA+Configurator command set
The settings of the TA+POX for the serial interface and the S bus interface are
called configuration. The TA+POX is delivered with a set of pre-set values. In the
following section it will be shown how, by using the configuration commands, you
can examine the configuration of the TA+POX and if necessary change it. The
values can be stored in non volatile memory; this means they'll remain unchanged
even if the power supply is disconnected.
You can configure the TA+POX in the following ways:
• by using TA+ configuration commands entered by a locally connected PC.
• by using TA+ configuration commands entered via the ISDN access (remote
configuration).
• by using the PAD (X.3) command set entered by a locally connected PC.
• by using the AT command set entered by a locally connected PC.
The TA+Configurator can be entered in the following ways:
• remote via ISDN (see page 48).
• by using a special command from the asynchronous dialup command interface
(PAD: “CONF” or AT: “ATCONF”).
• or escape sequence in power up phase if enabled (rsttim>10, rstmsg=1).
4.1 Configuring the TA+POX with AT commands
To execute one TA+configuration command cmd out of the AT command mode you
have to issue the command: "at**cmd" .
To call up the TA+Configurator please use the command "atconf".
You can leave the TA+Configurator by the command “quit” (or „exit“ or „go“).
Note: After altering one of the profile values marked by (#1) you have to give the
additional commands save and go. This is necessary to save and activate
these new parameters.
Note: All AT** commands has to be sent at the end of the command line.
4.2 Configuring the TA+POX with X.3 PAD
To execute one TA+configuration command cmd out of the X.3 - PAD command
mode you have to issue the command: “exec cmd” .
To call up the TA+Configurator please use the command “conf”.
You can leave the TA+Configurator by the command “quit”.
Note: After altering one of the profile values marked by (#1) you have to give the
additional commands save and go. This is necessary to save and activate
these new parameters.
46
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
4.3 Configuring the TA+POX after power on
For this entry you have to set the configuration parameter "rstmsg=1".
•
•
•
•
•
•
•
•
•
Connect the TA+POX to ISDN interface
Connect the PC's com-port to the DTE interface of the TA+POX.
Start a terminal emulation program (i.e. Hyper-Terminal) with the following
settings: 9600 Baud, 8 databits, No Parity (8N1)
Connect the TA+POX to the mains by the mains plug adaptor
Wait until LED 2 starts blinking (after about 5 sec, see config cmd “start“) and the
message to enter the config-sequence is displayed:
"+++ Press <CR>,<CR>,<ESC>,<ESC> to enter TA+Configurator +++"
Type in quickly the sequence <RET> <RET> <ESC> <ESC>, to call up the
TA+Configurator.
The TA+Configurator acknowledges by giving a welcome string and a “#“ as the
prompt character. Now you can work with the TA+Configurator by using the
configuration commands (see page 50).
Setup the parameter for the TA+POX from your terminal program and store
them.
Example:
To change the used B channel protocol to X.75 please enter the following
commands:
prot 10<↵> (set protocol to X.75)
save<↵>
(save the new configuration)
quit<↵>
(leave the TA+Configurator and activate the new value
settings)
Hint: The active set of parameters can be displayed on screen by the
TA+Configurator with the command "show<↵>".
Leave the terminal program and start your application.
Now you can use the TA+POX with the new set of parameters by running the
needed PC program.
© Stollmann Entwicklungs- und Vertriebs-GmbH
47
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
1.80D/09.2005
4.4 Remote Configuration using the TA+Configurator commands
The TA+POX to be configured is referred here as “remote TA+POX”.
The TA+POX to configure is referred as “local TA+POX”.
Please make sure that the remote TA+POX to be configured at the other end is
connected to the ISDN line and powered up.
•
•
•
•
•
•
•
•
Connect the local TA+POX to ISDN interface
Connect the PC's com-port to the DTE interface of the local TA+POX.
Connect the power supply to the mains socket.
Start a terminal emulation program (i.e. Windows-Terminal)
Configure the local TA+POX with the B channel protocol X.75 and blocksize
2048 (ATB10).
Set up an ISDN connection to the remote TA+POX to be configured by using
the command: ATD<ISDN-No>e<↵>. The extension "e" at the end of the
calling number gives a connection to the internal remote access of the
remote TA+POX.
The called TA+POX TA+Configurator acknowledges by requesting the
remote password. Please enter the correct password (default: no password,
just return). Now you can work with the TA+Configurator by using the
TA+Configurator commands (see page 46).
Configure the parameter for the remote TA+POX from your terminal program
and store them (if wanted). (see page 50).
Example:
To change the used B channel protocol to X.75 please enter the
following commands:
prot 10<↵> (set protocol to X.75 - blocksize 2048)
save<↵>
(save the new configuration)
Hint: The active set of parameters can be displayed on screen by the
TA+Configurator with the command "show<↵>".
If necessary the remote TA+POX can be reset using the command
"reset<↵>".
Hang up the ISDN connection by leaving the TA+Configurator using the
command quit.
Leave your terminal program. After the next reset the changes will be active.
Now the configured remote TA+POX with the new set of parameters can be used by
running the needed PC program.
48
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
4.4.1 Remote access control
Using the following commands you can setup a table, to allow only dedicated callers
to get a connection to the remote management facilities inside the TA.
If this list is empty (default) or one entry with a star (*) is set, any incoming call is
allowed.
Every incoming call that does not fit to one of the entries of acctab will be rejected
with the ISDN cause „call rejected“.
racctabx nn set entry number x to ISDN number nn
racctabx - clear entry number x
racctabx * Allow all incoming calls to be accepted
racctabx
Show entry number x
racctab
Show all entries
Maximum number of entries = 5
Maximum length of ISDN number = 20 digits
The ISDN number can contain wildcards:
* : represents one or more digits
? : represents exactly one digits
Example:
racctab1 1234567890
racctab2 *456*
racctab3 ?2345678??
racctab3 *
racctab3 -
; accept the only specified number
; accept all number with 456 somewhere in the
middle
; accept all number with 2345678 in the middle
preceded by one digit and followed by two digits.
; accept all incoming calls
; clear entry no. 3
© Stollmann Entwicklungs- und Vertriebs-GmbH
49
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
1.80D/09.2005
4.5 List of TA+Configurator commands
The TA+Configurator commands typed in must have the correct syntax and be
complete, including all blanks. Capital/small letter use is not important. The entry is
not case sensitive.
The bolded values are factory defaults. The usage is:
[?]<command>[=parameter]
Example to set the ISDN B channel protocol to X.75:
prot=10
Example to show the selected ISDN protocol:
prot
Example to show all selectable ISDN protocols:
?prot
To get an overview about the commands of your TA some major commands here as
a preview:
show
show the usually used parameter
showall
show all changeable parameter
quit
leave TA+Configurator
help
show all available commands
defa
setup default parameter set
defa 1
setup factory default parameter set
save
store parameter non volatile
acctab
Access table setup
Using these commands you can setup a table (max. 5 entries) to allow only
dedicated callers to get a connection to the TA.
acctabx nn/ss set entry number x to ISDN number nn and subaddress ss
acctabx clear entry number x
acctabx *
Allow all incoming calls to be accepted
acctabx
show entry number x
acctab
Show all entries
Note: for a detailed description see chapter 3.5.
50
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
atsx, atopt, atrej
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
AT command parameter set
AT command set only:
Handle AT specific settings.
Show and change AT S registers by entering the new value.
ats0
show setting of S0-Register
ats0=1
set Register S0 to 1
atopt
show option register (bit-values):
bit 0 : 01 => ATV1
bit 1 : 02 => ATW1
bit 2 : 04 => ATQ1
bit 3 : 08 => ATE1
bit 4 : 16 => ATS9=1
atrej
show reject register => setting of AT#R (0,1)
atrcs
show “return code selection”
This parameter equals AT command “ATXn
ATRCS=4 (default) equals “ATX4”
autosave
automatic storage of parameter values
automatic storage of parameters in the background of the TA process without
issuing the command AT&W or “save”.
This includes the parameter: (ISDN, IINIT, PTP,FTEI, MSN)
0: automatic saving disabled.
1: automatic saving enabled.
autosavetime
delay time for autosave
Sets the delay time for autosaving of parameters if enabled
Value in 1 ms counts.
10: automatic saving after 10 ms (default)
bc
bearer capability
Bearer capability for outgoing data calls. (default: 88 90; hex bytes)
(see note 2)
© Stollmann Entwicklungs- und Vertriebs-GmbH
51
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
br
1.80D/09.2005
baudrate asynchronous
Selection of the asynchronous baudrate for the DTE interface
0: Autobauding, (automatic bit rate adoption from 1200 bps to 230.400 bps)
1: 1200 bit/s
2: 2400 bit/s
3: 4800 bit/s
4: 9600 bit/s
5: 19200 bit/s
6: 38400 bit/s
7: 57600 bit/s
8: 115200 bit/s
9: 230400 bit/s
20: 300 bit/s
21: 600 bit/s
Note: Autobauding (br = 0) is available for AT command set only. If set and cmds is
changed to PAD, br will be set to 4 (9600 bit/s).
brn
line baudrate asynchronous V.110
Selection of the asynchronous baudrate for V.110 line (B channel)
0: Line baudrate equals local baudrate
1: 1200 bit/s
2: 2400 bit/s
3: 4800 bit/s
4: 9600 bit/s
5: 19200 bit/s
(See in addition note 3)
bsize
frame length
Maximum length of a data frame. This setting is valid for both received and
transmitted data frames.
prot=X.25-B
128
prot=X.31-D
128
prot=X.75
2048
prot=V.120
259
values:
32 .. 2048
52
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
casnr
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
ISDN number for callback dialing (option)
With the security callback function you can initiate the called TA+POX to
make an automatic call to a predefined ISDN number stored in casnr.
The callback has to be enabled or disabled by using the command
"cmds2=40".
casnr nn
casnr
catab
set callback number to ISDNnumber nn
show callback ISDNnumber
show table catab
Show setting of all entries of the table catab (max. 3 entries) for automatic
dialing.
catabx nn/ss set entry number x to ISDNnumber nn and subaddress ss
catabx clear entry number x
catabx
show entry number x
catab
Show all entries
cato
call timeout to abort
Time to abort a call if not successful connected after n seconds.
n = {3..255}, default: 15 seconds.
capa
call pause
Automatic call: set a call pause for n seconds before next call attempt.
n = 0 : immediate call retry. n={0..255}, default: 3 seconds.
catry
calls retry
Automatic call: max. no of tries of every number entry in catab.
n = 1 .. 255 :, default: 1
© Stollmann Entwicklungs- und Vertriebs-GmbH
53
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
ccts
1.80D/09.2005
CTS control
CTS control
0 : CTS follows RTS
1 : ON, HW FLC / hardware flow control RTS/CTS (default)
2 : CTS follows DTR
For nearer information see also chapter 3.3.
cdcd
DCD control
DCD control
0 : DCD always ON
1 : DCD indicates a connection (default)
2 : DCD follows DTR
For nearer information see also chapter 3.3.
cdsr
DSR control
DSR control
0 : DSR always ON
1 : DSR indicates a connection
2 : DSR follows DTR
For nearer information see also chapter 3.3.
cdtr
DTR control
Usage of DTR to control ISDN connection
0 : No control:
Incoming calls will be accepted independent of DTR status;
DTR drop does not disconnect an active connection.
2 : DTR off disconnects (default)
Incoming calls will be accepted only when DTR is ON;
DTR drop disconnects an active connection.
4 : DTR ignore and DTR drop disconnects
Incoming calls will be accepted independent of DTR status;
DTR drop disconnects an active connection.
For nearer information see also chapter 3.3.
54
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
chappwd
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
set password for PPP chap authorization
(only required for WINDOWS 95)
Enable ML-PPP CHAP authorization by setting the password corresponding to the
user name used for the PPP connection. If the server does not handle CHAP an
automatic fallback to PAP is performed.
chappwd=<password>
set password for CHAP
Note: Since the password is shown in plain text it may be disclosed by unauthorized
persons.
cipm
cip value mask
Selects the bearer services that can be accepted with an incoming call. The
definition of hbhbhbhb (double word) is the CIP mask as defined in the CAPI
2.0 specification (default 00000004).
Example:
cipm=00030012 : Accept analogue incoming calls
cipm=00000001 : Accept all incoming calls.
See also AT command AT#C1.
cipo
cip value outgoing
Selects the bearer service that will be sent with an outgoing call.
The value for hbhb (word) is the CIP value as defined in the CAPI 2.0
specification (default 0004).
Example:
an outgoing call as a voice call: AT#C1=0004.
See also AT command AT#C2.
cmds
command set
(note 1)
Command set for connection control
0:
AT command set (default)
1:
PAD X.3 command set
6:
Automatic dialing when DTR is set
7:
Automatic dialing when TxD is received by the TA
8:
Automatic dialing always connect
10:
Configurator (internal configuration command set)
12:
incoming calls only (no active connections)
Note: For details see the appropriate chapters.
After changing cmds via remote management the TA has to be reset using
the command "reset".
© Stollmann Entwicklungs- und Vertriebs-GmbH
55
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
cmds2
1.80D/09.2005
command set special behavior
Additional parameter to set special behavior with respect to the setting of the
command set.
0:
no special behaviour activated (default)
1:
Automatic Voice Connection (AVC) = ON (s. TA+HIT Specs)
2:
Ignore incoming data while connection is establishing (no disconnect
on receiving V.24 character)
10:
set compatibility to PAD CF-configuration for command save:
"exec save" will return "saving ... done"
11:
set compatibility to CF-configuration (TA+POS) for command save:
"save" will return "+OK saving .. +OK done"
40:
Security callback enabled
120: AT command set only: A "CONNECT" will be displayed always with
code 10 (ATV0).
cmlp
Multilink PPP control (option)
Call bumping: control of the second B channel connection with Multilink PPP
protocol. When set, any incoming voice call will automatically drop one B
channel connection if a Multilink PPP session is active. The second B
channel of the Multilink session will not be established after voice connection
is released.
0:
1:
no call bumping
call bumping for incoming voice calls
cpua, cpua2, cpl3
Output pin behavior (TA+HUX only)
Definition of the behavior of the output pins UA UA2 and L3 of TA+HUX.
The behavior can be configured by using one of the following setting to the value of
the list below.
The output level can be inverted by adding 128 to the desired value (defines the
output pin to low active).
0:
1:
2:
3:
56
always OFF. Default UA2
always ON
ISDN activation, blinking 0.5 sec OFF, 0.5 sec ON
ISDN activation: ON = activated, OFF = deactivated
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
10:
11:
12:
20:
21:
22:
29:
40:
41:
dad
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
Default TA+HUX: UA
B-channel occupied for any port(D-channel SETUP ACK, OFF HOOK)
Default: L3
B-channel occupied for data port (D-channel SETUP ACK, OFF
HOOK)
B-channel occupied for voice or ext. IOM-2 (D-channel SETUP ACK,
OFF HOOK)
B-channel connected, but not synchronized for any port (D-channel
CONNECT)
B-channel connected, but not synchronized for data port (D-channel
CONNECT)
B-channel connected for voice or ext. IOM-2 (D-channel CONNECT)
B-channel synchronized for data port, equals DCD on V.24.
Alarm output (customer specific)
Message incoming VOICE CALL (RI) (customer specific)
If VATS0=0, incoming call will signaled by switching level (1 sec. ON, 4
sec. OFF) until connection
If VATS0=1/2 => B-channel connected for ext. IOM-2 (D-channel
CONNECT)
ISDN destination address
Destination address for ISDN X.25-B channel (prot 20) calls in the PAD command
interface. If no ISDN number is set in the call command line the entry “DAD” will be
used as ISDN called number.
dbits
asynchronous databits
Number of data bits asynchronous chars
(default: 8) 7,8
Note: To use other data formats than 10 bit (= (N1, 7E1, 7O1) you have to set br to
fixed speed.
© Stollmann Entwicklungs- und Vertriebs-GmbH
57
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
debloc
1.80D/09.2005
deblocking of S bus occupation
Reserved functionality: for alarm purposes it can be necessary to debloc one
or both B channels that are occupied by another device connected to the Sbus. This functionality is only allowed to be used to help in emergency
conditions like fire or burglar alarm situations.
debloc 1:
Free first B channel of the S-bus.
debloc 2:
Free both B channels of the S-bus.
defa
default settings
Sets up factory default parameter setting.
defa 0:
setup all parameter concerning data port
defa 1:
setup all parameter including parameter
(ISDN, IINIT, PTP,FTEI, PROT, MSN, RPWD)
dte
B channel link address
Selects the Layer 2 link addresses for ISDN B channel. Only valid for protocols that
are HDLC based (X.75, LAPB, X.25-B).
0
Calling side reacts as DTE,
called side reacts as DCE
(default for several protocols, prot=10, 13, 22, 23)
1
TA reacts as DTE (own adr = 01)
(default for X.25 protocol, prot=20, 21)
3
TA reacts as DCE (own adr = 03)
Note: The value will be changed by setting the B channel protocol (prot).
dud
User data for X.25 / X.31 call requests
Definition of the user data, that will be automatically added with an outgoing X.25
call request.
dud 010202FF:
set user data to hexadecimal 0x01, 0x02, 0x02, 0xff
dud clear default user data.
58
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
flc
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
flowcontrol
Flowcontrol to DTE
0 : No flowcontrol
3 : Hardware flowcontrol RTS/CTS in the data mode
4 : Software flowcontrol XON/XOFF
For nearer information see also chapter 3.2.
ftei
tei value point to point, fixed tei
Reserved functionality, Point to Point mode only:
Value of the terminal equipment identifier for fixed tei connections. This value is set
to 0 per default and should not be changed.
0..63
tei value as defined will be used (default: 0)
127
automatic tei procedure will be used
Note: changing the type of ISDN access by setting the parameter "ptp" will
automatically change the parameter "ftei".
These values get active after sending "save" command and a reset of the TA.
fwload
load new firmware
(8Mbit Flash memory required)
(option)
This commands loads new firmware into the TA without starting.
The firmware will be stored into the upper not used part of the flash memory. While
uploading the following checks will be performed:
- File transfer protocol is XMODEM1K
- An overall firmware checksum is used.
- The firmware type written in the module header of the firmware must be
compatible to the hardware- and allowed firmware type (stored inside the
Bootloader).
NOTE: If the flash memory size is only 4Mbit this command is not supported.
fwstart
start new firmware (8Mbit Flash memory required) (option)
This command starts new firmware previously stored within the TA.
The firmware stored in the upper part of the flash memory will be loaded into the
executable part of the FlashProm and started, if the following conditions are met:
- the overall firmware checksum must be correct.
© Stollmann Entwicklungs- und Vertriebs-GmbH
59
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
1.80D/09.2005
The firmware type written in the module header of the firmware must be
compatible to the hardware- and allowed firmware type (stored inside the
Bootloader).
Starting includes a hardware reset of the TA.
Note: If new functionality has been added, your last stored configuration may be
lost.
If the flash memory size is only 4Mbit this command is not supported.
-
glmsni
accept incoming calls without called party number
This parameter controlles the behaviour of incoming calls without called party
number.
0: disable the acceptance of incoming calls without calles partx number
1: enable the acceptance of incoming calls without called party number
(default)
idle
Idle data timeout
Timer to disconnect the ISDN B channel connection after inactivity (sec).
0: inactive (default)
1..n: delay time to disconnect in seconds (1..255).
iinit
ISDN initialisation after power ON
Defines the behavior of the TA after Reset. If set to 1 the ISDN interface will
automatically activated after Power ON. As a result, the LED1 will show the correct
state regarding the ISDN line.
If set to 0, the TA stays passive to the ISDN line after power On, the LED1 will stay
blinking till the first successful communication through the ISDN line takes place.
iinit 0 :
no activation after Power On
iinit 1 :
Automatic activation after Power On
iinit 2 :
Automatic activation every time the S-Bus is deactivated
iinit 3 :
Automatic Tei-Request after Power On
iinit 4 :
Automatic Tei-Request and LAPD link setup after Power On
iinit 5 :
Automatic Tei-Request and LAPD link setup and RESTART
after Power On (ISDN point to point mode, all connections will
be cleared)
iinit 6 :
Automatic Tei-Request and LAPD link setup permanently
60
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
ireset
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
Idle hardware reset
Timer to reset the TA (min). The TA will be reset automatically, if no successful
ISDN connection has been established within the time defined by ireset.
0: inactive (default)
1..n: delay time for reset in minutes (1..65535).
Note: AT commands will not prohibit the timer to expire.
isdn
ISDN D channel protocol
Selects ISDN D channel protocol
0: DSS1 (Euro-ISDN)
(default)
1: 1TR6 (Germany national)
5: National ISDN-1/2 (USA)
6: NTT INS-NET (Japan)
7: AT&T 5ESS (USA)
8: VN4 (France)
12: leased line with usage of just B channel B1
13: leased line with usage of just B channel B2
14: leased line with usage of both B channels.
k
(note 1)
(option)
(option)
(option)
(option)
(option)
(option)
(option)
windowsize
Layer-2 protocol: windowsize (default:7). k = {1..7}
Value will be automatically changed with changing B channel protocol prot.
The default value for "prot=21" (X.31 D channel) is set to k=3".
lcgr
logical group number X.25
Logical group number for X.25 packet layer protocol.
lcgr = {0..255}, default: 0
llc
low layer compatibility
Low layer compatibility for outgoing calls (Hex bytes)
(see note 2 and 3)
© Stollmann Entwicklungs- und Vertriebs-GmbH
61
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
load
1.80D/09.2005
Load stored parameter setting
All parameters stored in non volatile ram will be loaded.
msn
Multiple Subscriber Number
Own MSN (Multiple Subscriber Number)
msn *
msn nn
msn nn/ss
msn msn
global msn, all incoming calls will be accepted, no outgoing msn
(default)
set msn to nn, nn = string of digits incl. “*,#“ (max length = 22)
set msn to nn, and subaddress to ss = string of chars (max 22)
no acceptance of incoming calls.
show current setting.
The msn is automatically stored to non volatile ram without sending command save.
By the ISDN protocol 1TR6 only the last digit is used.
npl
Select numbering plan outgoing
Selects the numbering plan that will be sent with an outgoing call in the fields
destination address and origination address.
Default:
80 (unknown numbering plan)
The value for hb (hexadecimal coded byte) is the numbering plan value as defined
in the ETS specification ETSI 300 102.
Definition and coding of numbering plan (hb):
Type of number:
Bits
8765
1000
(8x)
unknown
1001
(9x)
international number
1010
(Ax)
national number
1011
(Bx)
network specific number
1100
(Cx)
subscriber number
1110
(Ex)
abbreviated number
1111
(Fx)
reserved for extension
All other values are reserved.
62
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
Numbering plan:
Bits
4321
0000
(x0) unknown
0001
(x1) ISDN/Telephony numbering plan
0011
(x3) data numbering plan
0100
(x4) telex numbering plan
1000
(x8) national standard numbering plan
1001
(x9) private numbering plan
1111
(xF) reserved for extension
All other values are reserved.
nplnat
Coding national numbering plan
Defines the conversion of the number of an incoming call with numbering plan
coding national number. The received numbering plan (parameter npl) will be set to
unknown.
nplnat nplnat nn
nplint
no conversion of ISDN number
ISDN number will be changed to preceding numbers as defined
in nn. (default: "0").
Coding international numbering plan
Defines the conversion of the number of an incoming call with numbering plan
coding international number. The received numbering plan (parameter npl) will be
set to unknown.
nplint nplint nn
nui
no conversion of ISDN number
ISDN number will be changed to preceding numbers as defined
in nn. (default: "00").
nui and password
Setup nui and password sent with an outgoing X.25 call packet.
nui and password has to be entered as ASCII characters.
(X.25 B channel and X.31 D channel only)
© Stollmann Entwicklungs- und Vertriebs-GmbH
63
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
ox25nr
1.80D/09.2005
own X25 address
defines the own X.25 address for outgoing call request using X.25 in B channel.
pxxx
X3 parameter set
PAD X.3 command set only:
show setting of one X3 parameter.
Change X3 parameter by entering the new value.
p001
show setting of X3 parameter 0
p001=1
set X3 parameter 0 to 1
Note: See chapter separate chapter for supported pad parameter.
prot
B channel protocol
Transmission protocol for data transfer
0:
V.110 asynchronous
3:
HDLC async to sync conversion (PPP asynchronous)
4:
HDLC transparent (octets are packed into HDLC frames)
5:
Byte transparent voice connection (raw B channel data)
10 : X.75 SLP
13 : V.120 async
20 :
X.31 B channel (X.25 B channel)
21 : X.31 D channel
22 : T.70NL
23 : T.90NL
31 : MLPPP (Option)
40 : B channel transparently switched to IOM-2
prty
asynchronous parity
Parity of asynchronous character (default: no parity)
0 : No parity; 1 : Odd parity; 2 : Even parity
Note: To use other data formats than 10 bit (8N1, 7E1, 7O1) you have to set the
parameter of the serial bps-rate "br" to a fixed speed ("br" unequal "0").
64
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
ptp
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
ISDN interface type
Select type of ISDN interface:
0:
select multipoint mode (to connect ISDN terminals, default)
1:
select point to point mode (to connect ISDN switching systems)
pvc
use of pvc type X.25 connections
Enable usage of permanent virtual connections instead of switched logical
connections.
pvc = 1 : enable pvc, default: 0
quit, exit, go
activate parameter changes
Activates the actual parameter settings and leave the TA+Configurator (without
storing the parameter in non volatile memory ).
racctab
Access table setup for remote access
Using these commands you can setup a table (max. 5 entries), to allow only
dedicated callers for remote management to get a connection to the TA.
racctabx nn set entry number x to ISDN number nn
racctabx - clear entry number x
racctabx * Allow all incoming calls to be accepted
racctabx
show entry number x
racctab
Show all entries
Note: for a detailed description see chapter 4.4.1.
reset
reset TA+POX
Resets the whole functionality of the TA+POX by a forced hardware reset (like
Power off / on). Refer also to parameter rsttim.
Note: If you reset a TA from remote management the "resetted" TA will loose it's
connection to the ISDN network. Due to timeouts of the ISDN network it can
take up to 30 seconds till the local TA will notify the released connection.
© Stollmann Entwicklungs- und Vertriebs-GmbH
65
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
ringtimer
1.80D/09.2005
delay of RING messages
Delay time between two RING messages, if S0 register is set not equal to 1,
value in 100 ms.
Default: ringtimer = 50 (5 sec).
rmmsg
RMON/RMOFF message for remote (option)
Display message "rmon" rsp. "rmoff" for established rsp. disconnected remote
configuration access. If an PAD connection is established the message will
be discarded.
0 : display no messages
1 : display messages
rmsn
Multiple Subscriber Number for remote
MSN (Multiple Subscriber Number) for remote configuration
*: no specific MSN, all incoming calls accepted (default).
rmsn *
rmsn nn
rmsn rmsn
global msn, all incoming remote calls will be accepted.
set "rmsn" to nn = string of digits (max length = 22)
no acceptance of incoming remote calls
show current setting of "rmsn".
NOTE: The remote connection needs to get an incoming call with a special LLC
value "88 90 21 58 00 BB" which is automatically set in the additional "e" of the dial
command from the connecting Stollmann ISDN TA.
rpwd
password
Password for remote configuration (character input), max length 32 character.
To disable password please enter: “rpwd –“ (default).
rpwd no remote password is set
rpwd nn
set "rpwd" to nn = string of digits (max length = 32)
rpwd
show current setting of "rpwd".
66
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
rstmsg
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
startup message
Startup message:
"+++ Press <CR>,<CR>,<ESC>,<ESC> to enter TA+configurator +++"
after start up can be displayed with a fixed speed of 9600 bps, 8 data bits, no parity,
1 stop bit.
0: inactive, no startup message will be send after power on. (default)
1: active, startup message will be send after power on
rsttim
startup timer
Startup delay timer after reset. Within this period the configuration can be entered
after reset.
1 .. 255 :
reset phase in 100 milliseconds, default: 40 (4 seconds)
rsub
remote sub address
SUB (sub address) for remote configuration
*: no specific SUB, all incoming calls accepted (default).
rsub *
global SUB, all incoming remote calls will be accepted.
rsub nn
set "rsub" to nn = string of digits (max length = 22)
rsub no acceptance of incoming remote calls
rsub
show current setting of "rsub".
NOTE: The remote connection needs to get an incoming call with a special LLC
value "88 90 21 58 00 BB" which is automatically set in the additional "e" of the dial
command from the connecting Stollmann ISDN TA.
s0led
automatic ISDN (S bus) activation
Defines how the terminal adapter will handle an automatic ISDN (S bus) activation.
When automatic, the LED L1 will always state the activation state of the ISDN line.
0: Automatic activation after deactivation from ISDN network
1: no automatic activation (default).
save
store parameter changes
Stores the actual set of parameters in non volatile memory
© Stollmann Entwicklungs- und Vertriebs-GmbH
67
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
sbits
1.80D/09.2005
number of stopbits
Number of stopbits of asynchronous character
1 : One stopbit (default); 2 : two stopbit
Note: To use other data formats than 10 bit (= (N1, 7E1, 7O1) you have to set br to
fixed speed.
sbsize
serial port buffer size
Maximum length of a serial data frame. This setting is valid for both received and
transmitted data frames.
sbsize=0
uses the same maximum data frame length on the serial
interface and on the ISDN interface ( parameter “bsize”).
prot=X.25-B
bsize/sbsize = 128
prot=X.31-D
bsize/sbsize = 128
prot=X.75
bsize/sbsize = 2048
prot=V.120
bsize/sbsize = 259
sbize=32
uses the serial port buffer size of 32 byte
values:
bsize/sbsize = 16 .. 2048
The value of „sbsize“ should be smaller or equal to „bsize“.
Note: This parameter can be used to forward the transmission of serial data
when parameter “txfwd” will not help.
send3p
transmit AT escape characters
Setting determines whether the escape characters of AT command set (i.e.
+++) to switch to command mode will be transmitted via ISDN connection.
0: Escape characters will not be sent
1: Escape characters will be sent (default)
show
show parameters
Displays the actual set of parameters
68
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
showall
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
show all parameters
Displays the all accessible parameters
spid1, spid2
set spid
(option)
For ISDN lines in the U.S. you have to set the SPID. You get it from your ISDN
provider.
spid1=xxx Set SPID 1
spid2=xxx Set SPID 2
status
Global status of TA
The overall status of the TA will be displayed.
Example:
Current status information TA+POX
serial line: DTR:on, RTS:on, DSR:on, CTS:on, DCD:on, RI:off
ISDN: L1:up
Dch: Prot:DSS1, State:connected, CdPN:291, CgPN:509, prev error: 0
Bch: Prot:X.75 SLP, State:connected, CdPN:291, CgPN:509
sub
Subaddress
Select own subaddress that will be sent with an outgoing call as called party
subaddress with max. 20 digits
*: no subaddress setup (default)
The subaddress is automatically stored to non volatile ram.
svcio
logical channels svc
Maximum number of switched virtual logical channels for incoming and
outgoing X.25 connections.
svcio = {1..15}, default: 1
© Stollmann Entwicklungs- und Vertriebs-GmbH
69
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
t320
1.80D/09.2005
timer delay ISDN disconnect
Delay time between the clear message of the last X.25 connection and an
automatic ISDN disconnect. Only valid for X.25 B channel.
0: immediate ISDN disconnect (default)
1..n: delay time in seconds (1..254).
255: immediate ISDN disconnect
The released X.25 connection will be signaled due to the selected mode (via
response "NO CARRIER", CLR xxx or DCD goes inactive). The not yet
released ISDN connection is not signaled, also the released ISDN connection
has no signal.
The timer t320 will be used (or not) independent whether the local or remote
TA has disconnected the connection.
tdi
timer delay incoming call
Delay time between receiving ISDN incoming data call and signaling via RING or
CONNECT message.
0: no delay (default)
1..n: delay time in 50 ms ticks.
tei
TEI value
X.31 D channel only:
Terminal equipment identifier. This value must be identical to the tei of your basic
rate access, will be defined by your ISDN supplier.
tei=1 (default)
trcnnn
commands for internal trace
The usage of the commands for internal trace are described in chapter 5.6.
70
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
txfwd
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
timer for data forwarding
If no additional character to the already entered characters is entered within the
defined period, the already received serial data will be transmitted to the ISDN using
the selected transmission protocol.
(comparable to the functionality of X.29 parameter 4, data forwarding timer)
0:
minimum delay time (app. 10 ms) (default)
1..n: delay time in 10 ms ticks
Note: Valid for AT command set and X.75, X.25 B channel or X.25 D channel only.
typ
display of special type string
Displays version information in a special format.
ver
show version string
Displays detailed information about the software version and TA type.
verb
show version string of bootloader
Displays detailed information about the bootloader version.
v110dft
V.110 data format
Set the V.110 data format in the B-channel fixed to 8 bit transparent independent of
the local serial data format.
0:
uses the local serial data format also as V.110 data format (default)
1:
uses the V.110 data format (8 databits, no parity, 1 stupbit)
v110llc
Usage of LLC for V.110 connections
Set LLC parameter for incoming and outgoing V.110 connections.
0:
LLC is ignored and not created.
1:
outgoing call: an LLC is sent deriving from the settings of the TA
incoming call: the received LLC is used to setup the parameters for the
V.110 connection (default).
© Stollmann Entwicklungs- und Vertriebs-GmbH
71
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
v110flc
1.80D/09.2005
Usage of V.110 flowcontrol
Controls the ISDN flowcontrol for V.110 connections.
0:
V.110 flowcontrol via xbits will be ignored (default).
1:
V.110 flowcontrol via xbits enabled.
w
B channel windowsize L3
B channel layer 3 protocol: windowsize (default:2). w = {1..7}
Value will be automatically changed with changing B channel protocol prot.
xnr
own X.25 address
Setup an origination X.25 address.
xnr nn
set "xnr" to nn = string of digits (max length = 15)
xnr erase the current value of “xnr” value
xnr
show current setting of "xnr".
Only necessary, if not supported from the network
xtab
(X.31 B channel only)
show table xtab
Show setting of all entries of the table xtab (max. 5 entries) for translation of
X.25 address to ISDN number.
For details see chapter 3.9.
72
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
X25mb
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
handling more data bit (M-Bit)
All characters out of X.25 packets that are continued using the “more data bit“
(M-Bit) will output to the V.24 interface as a contiguous data stream (without
any pauses). All from the ISDN line received X.25 packets with more data bit
set will be collected inside the TA+POX. Output to the V.24 interface will be
started if
- an X.25 packet without „more data bit“ set is received or
- +a data length of 2048 octets is assembled or
- latest after 3 seconds.
0:
received X.25 data will be output independent of setting of M-Bit
(default)
1:
received X.25 data will be collected till M-Bit off.
x31rr
enable rerouting for X.31 D channel (option)
Enable automatic establishment of an X.25 B channel connection if the X.31
D channel connection fails using the entries of table xtab.
0:
no rerouting
1:
automatic rerouting enabled
(X.31 D channel only)
<cmd>?
more information for one command
Displays the allowed values for one selected command <cmd>
??
help
Displays help texts for all commands
© Stollmann Entwicklungs- und Vertriebs-GmbH
73
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
1.80D/09.2005
Notes:
(Note1)
After issuing one of these parameter you should execute the "save"
command to store the configuration in non volatile memory. To activate and
use the new setting you have to run the "go" (or "reset") command.
(Note2)
Command syntax for setting hlc, llc and bc
An empty parameter has to be entered by "-".
Example:
Deleting of LLC-value:
LLC -<↵>
Entering a new LLC:
LLC 8890<↵>
(Note3)
Different modes for V.110 baudrate adoption
- Outgoing call:
brn # 0 :
ISDN message SETUP will be created with or without LLC(brn)
depending on the setting of dial.v110llc;
The B channel (V.110 baudrate) will use the baudrate set by brn
(independent of br or recognized local baudrate)
brn = 0 :
"adaptive": same mechanism as brn # 0; the V.110 baudrate will
be created by br rsp. the recognized local baudrate.
- Incoming call:
brn # 0 :
no LLC received: accept incoming call, use in B channel brn for
V.110 baudrate.
LLC received compliant to brn: accept incoming call
LLC received not equal to brn: Reject incoming call:
DISCONNECT (cause = incompatible destination).
brn = 0 :
"adaptive":
no LLC received: accept incoming call, use in B channel br rsp.
the recognized local baudrate for V.110 baudrate.
LLC received: accept incoming call, use in B channel the
baudrate derived from the LLC as V.110 baudrate.
The usage of the LLC is controlled by the TA+Configurator command
dial.v110llc.
74
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
4. TA+Configurator command set
4.6 Software update
The TA+POX uses a Flash-EPROM for software updates to store the operational
software. This software can be updated from a local connected PC via the COM
port. Please fulfill the following steps to update the TA+POX:
•
•
•
•
•
•
•
•
Start a terminal emulation on your PC with the capability to run an X-MODEM file
transfer (i.e. HyperTerminal).
Enter the AT command "AT**FLASH" to start the update procedure.
The TA+POX will send the message "Erasing flash EPROM now. Please wait...".
After erasing of the Flash-EPROM the TA send out the request of the download
procedure with the 1kX-MODEM protocol:
"Start your XMODEM transfer now (Ctrl-X aborts) ..."
Start the 1kX-MODEM file transfer (send file or upload) by selecting the Transfer
/ Send File menu point in your terminal emulation and select the new software.
The internal timeout of each X-Modem block is set to 10 seconds.
After completion you will get the information whether the software update ended
successfully or erroneous.
- Positive result:
- "Loading procedure ended successfully".
- Negative reason:
- "Checksum error." (for example)
Negative result:
- "Flash EPROM software is probably not executable".
The loaded new firmware will automatically start after a software reset.
(Give the TA about 15 seconds to activate the new software.)
Due to new functionality the last stored configuration setting may be lost, please
check before using.
Note:
Due to an error it may be that no firmware is active within the TA. This will be
indicated by flashing of the LEDs (Bootloader active). To store a new
firmware correctly you have to enter the command "AT**FLASH" again and
load a firmware using the XMODEM protocol as described above. This
bootloader supports only AT**cmd with a fixed baudrate of 115.200 Baud.
© Stollmann Entwicklungs- und Vertriebs-GmbH
75
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
5 Diagnostic and error messages
For the diagnostic of erroneous situations the following functionality is supported.
Please check first the behavior of LED displays, if an ISDN connection can not be
established. Refer to list of LED displays on page 94.
5.1 Error messages from AT command set
In AT command mode, error cause display (does not belong to the AT command
standard) can be turned on by issuing the command ATW1. The shown error
causes use the coding defined by the CAPI definition. ISDN error causes from the
ISDN network are always coded as 34xxH, where xx represents the hexadecimal
version of the ISDN error cause (see page 78). All other causes are CAPI error
causes (see page 86).
Error cause display:
<xx> = ISDN release (error) cause, hexadecimal
Example:
Tx data
ATW1
Rx data
OK
ATD12345
NO CARRIER <34A2>
76
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
5.2 Error messages of the integrated PAD
For the diagnostic of erroneous situations - e.g. no X.25-connection possible - the
following error indicators are supported.
If an error occurs during the establishment of an X.25-connection, a reason for the
failure of the connection establishment or the release of an established connection
will be indicated in accordance to the configured indication type.
See parameter 6: Indication according to ITU, Datex-P, with English extension.
The following error indicators are supported:
•
Error codes during establishment of an X.25-connection:
Indication as part of the Connection-Release-Message.
E.g.: "CLR OCC diag" or
"CLR DER 0 <zzzzH>"
or
"Datex-P: connection released"
or
"connection released, reason xx diag yy [<zzzzH>]".
xx shows the hexadecimal coding of the X.25 release cause and
yy shows the hexadecimal coding of the diagnostic.
zzzz shows the hexadecimal coding of the CAPI cause.
© Stollmann Entwicklungs- und Vertriebs-GmbH
77
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
5.3 Table of ISDN causes and their explanation (DSS1)
Cause
Decimal /
Hexadecimal
1 / 0x81
2 / 0x82
3 / 0x83
6 / 0x86
7 / 0x87
16 / 0x90
17 / 0x91
18 / 0x92
19 / 0x93
20 / 0x94
21 / 0x95
22 / 0x96
26 / 0x9A
27 / 0x9B
28 / 0x9C
29 / 0x9D
30 / 0x9E
31 / 0x9F
34 / 0xA2
38 / 0xA6
41 / 0xA9
42 / 0xAA
43 / 0xAB
44 / 0xAC
46 / 0xAE
47 / 0xAF
49 / 0xB1
50 / 0xB2
53 / 0xB5
55 / 0xB7
57 / 0xB9
58 / 0xBA
63 / 0xBF
78
Meaning
Translation
to
AT
result
codes
Translation
to
X.25
cause
+
diagnostic
Unallocated (unassigned) number
No route to transit network
No route to destination
Channel unacceptable
Call awarded and being delivered in an
established channel
Normal clearing
User busy
No user responding
No answer from user (user alerted)
No answer from user (device off)
Call rejected
Number changed
Non selected user clearing
Destination out of order
invalid number format
Facility rejected
Response to STATUS ENQUIRY
Normal disconnect, unspecified
No circuit/channel available
ISDN network out of order
Temporarily failure
switching equipment congestion
Access information discarded
Requested circuit/channel not available
Precedence call blocked
Resource unavailable, unspecified
Quality of service unavailable
Requested facility not subscribed
Outgoing calls barred within CUG
Incoming calls barred within CUG
Bearer capability not authorized
Bearer capability not presently available
Service or option not available,
3
3
3
6
6
13, 78
0D, 78
0D, 78
05, 78
05, 78
3
7
8
8
8
8
3
3
8
3
3
3
3
7
6
6
6
6
6
6
6
3
3
3
3
3
3
3
00, 78
01, 78
09, 78
09, 78
09, 78
21, 78
0D, 78
00, 78
09, 78
13, 78
13, 78
13, 78
00, 78
01, 78
05, 78
05, 78
05, 78
05, 78
05, 78
05, 78
05, 78
13, 78
13, 78
13, 78
13, 78
13, 78
13, 78
13, 78
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
Cause
Decimal /
Hexadecimal
65 / 0xC1
66 / 0xC2
69 / 0xC5
70 / 0xC6
79 / 0xCF
81 / 0xD1
82 / 0xD2
83 / 0xD3
84 / 0xD4
85 / 0xD5
86 / 0xD6
87 / 0xD7
88 / 0xD8
90 / 0xDA
91 / 0xDB
95 / 0xDF
96 / 0xE0
97 / 0xE1
98 / 0xE2
99 / 0xE3
100 / 0xE4
101 / 0xE5
102 / 0xE6
103 / 0xE7
111 / 0xEF
127 / 0xFF
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
Meaning
unspecified
Bearer capability not implemented
Channel type not implemented
Requested facility not implemented
Only restricted digital information bearer
capability is available
Service or option not implemented,
unspecified
Invalid call reference value
Identified channel does not exist
A suspended call exists, but this call
identity does not
Call identity in use
No call suspended
Call having the requested call identity
has been cleared
User not member of CUG
Incompatible destination
Non-existent CUG
Invalid transit network selection
Invalid message, unspecified
Mandatory information element missing
Message type non-existent or not
implemented
Message not compatible with call state
or message type non-existent or not
implemented
Information element /parameter nonexistent or not implemented
Invalid information element contents
Message not compatible with call state
Recovery on timer expiry
Parameter
non-existent
or
not
implemented, passed on
Protocol error, unspecified
Network interworking error, unspecified
© Stollmann Entwicklungs- und Vertriebs-GmbH
Translation
to
AT
result
codes
Translation
to
X.25
cause
+
diagnostic
3
3
3
3
13, 78
13, 78
13, 78
13, 78
3
13, 78
3
3
3
21, 78
21, 78
21, 78
3
3
21, 78
21, 78
21, 78
3
3
3
3
3
3
3
21, 78
21, 78
21, 78
21, 78
21, 78
21, 78
21, 78
3
21, 78
3
21, 78
3
3
3
3
21, 78
21, 78
21, 78
21, 78
6
6
05, 78
05, 78
79
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
5.4 X.25 causes and their explanation
5.4.1 X.25 causes in Clear packet
Coding of the field "cause" in packet "Indicate-Cause".
00
01
03
05
09
0B
0D
11
13
19
21
29
80
DTE/CONF
OCC
INV
NC
DER
NA
NP
RPE
ERR
RNA
ID
FNA
Triggered by the remote DTE/DCE
Remote DCE busy, dialed number busy/engaged
Facility requested not valid/supported
Temporary disturbance in network
Remote DTE doesn't answer/out of operation
Access not available
No access with this dial number
Remote procedural error, sequence error
Local procedural error, sequence error
Reverse charging not accepted
Remote DTE/DCE incompatible
Incompatible connection request; receipt of single packet not
agreed upon
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
5.4.2 X.25 diagnostic codes
No.
hex
00
01
02
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2C
30
31
32
33
34
35
Restartind. Resetind. Meaning
Clearind.
Diagnostic
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
X
X
X
PVC
PVC
X
X
PVC
PVC
X
X
X
X
X
X
X
PVC
-
X
X
X
X
X
X
X
X
X
No additional information
Invalid P (S)
Invalid P (R)
Packet type invalid
Packet type invalid for state r1
Packet type invalid for state r2
Packet type invalid for state r3
Packet type invalid for state p1
Packet type invalid for state p2
Packet type invalid for state p3
Packet type invalid for state p4
Packet type invalid for state p5
Packet type invalid for state p6
Packet type invalid for state p7
Packet type invalid for state d1
Packet type invalid for state d2
Packet type invalid for state d3
Packet not allowed
Unidentifiable packet
Call on one-way logical channel
Packet type invalid for state at PVC
Packet on unassigned logical channel
Reject not subscribed to
Packet too short
Packet too long
Invalid general format identifier
Restart or registration packet »0«
Packet type not compatible with facility
Unauthorized interrupt conformation
Unauthorized interrupt
Unauthorized reject
Time expired:
- for incoming call
- For clear indication
- For reset indication
- For restart indication
- For call deflection
© Stollmann Entwicklungs- und Vertriebs-GmbH
81
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
40
41
42
43
44
45
46
47
48
49
-
X
X
X
X
X
X
X
X
X
X
-
X
-
4A
4B
4C
4D
4E
-
X
X
X
X
X
-
-
51
52
53
54
61
62
64
65
66
67
71
72
73
74
75
76
77
78
79
7A
80
80
81
81
82
82
X
X
-
X
X
X
X
X
X.75
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
PVC
PVC
PVC
X
X
X
X
X
X
-
82
1.80D/09.2005
Call set-up, call clearing or registration problem
Facility/registration code not allowed
Facility parameter not allowed
Invalid called DTE address
Invalid calling DTE address
Invalid facility/registration length
Incoming call barred
No logical channel available
Call collision
X.25: repeated facility request
X.75: missing transit DNIC
Non zero address length
Non zero facility length
Facility not provided when expected
Invalid ITU-specified DTE-facility
max. number of call redirections or call deflections
exceeded
Improper cause code from DTE
Not aligned octet
Inconsistent Q bit setting
NUI problem
DNIC not accessible
Unknown transition DNIC
Wrong use of facility
Erroneous length of Net-Indicator
Length of Net-Indicator not equal zero
Erroneous M-Bit
Problem concerning remote net
International net problem
Transmission section out of operation
International line engaged
Error in the transit net
Error in the destination net - invalid facility found
International routing problem
Temporary routing problem
Unknown called DNIC
Service
Erroneous Q-Bit or
No operation means available
Single packet not agreed upon or
Temporarily out of operation
Cause-flied not equal 00 (hex.) or
Closed by service provider, e.g. DATEX-P
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
83
84
85
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
X
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X.75
X.75
X.75
X
PVC
X
X
PVC
PVC
PVC
PVC
X
X
X
-
-
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
PVC
-
-
Incompatible packet length
Erroneous M-Bit
Rejection of the connection request or
NUI-call no more granted
PVC-Access description erroneous
Clear by service provider, e.g. DATEX-P
DNIC not accessible
Reverse charging not agreed upon
Missing agreement
Missing number of calling station
Erroneous number of calling station
Transmission section interrupted
Transmission section out of operation
Time expired DATEX-P state P1
Erroneous coding of cause
Erroneous direct call
Uncompleted octet found
Facility valid
Erroneous use of facility
Erroneous address in packet »Call-Accepted«
Invalid interrupt packet in subnet
Invalid interrupt acknowledge in subnet
Only single packet with limitation of response entry
permitted
Incompatible PVC
Erroneous agreement of window size
Missing fields
Erroneous address length
Erroneous length of facilities
Incomplete field
Incompatible transmission rate class
Group call number out of order
Group call number not accessible
Group call number temporarily out of order
Erroneous address
Erroneous sub address
Erroneous format of net facility
Length of net facility not equal 0
No user data
Missing indicator for national facility
Access to users of the same service blocked
Number temporarily not accessible
User recognition required in the packets
© Stollmann Entwicklungs- und Vertriebs-GmbH
83
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
AC
-
X
-
-
AD
AE
AF
B0
B1
-
X
X
X
X
X
-
-
B2
B5
B6
B7
C0
C1
C2
C3
C4
C5
C8
-
X
X
X
X
X
X
X
X
X
X
X
-
-
C9
FF
X
X
X
X
X
1.80D/09.2005
»Connection-Request« and »Call-Accepted«
Called subscriber has not agreed upon the facility
"Single Packet"
Network internal Load-Request received *)
Network component error *)
Network failure of a virtual connection *)
Network internal restart request received *)
Erroneous number of called station in the packet
»Call-Accepted«
Unknown network faculty
X.32 dial access not available
X.32 dial access not available
Reserved
X.25 dial access: Service data error
X.25 dial access: Service data error
X.25 dial access: User data erroneous
X.25 dial access: Procedural error
X.25 / X.32 dial access: Modem error
X.25 / X.32 dial access: Modem error
X.25 dial access: successful connection
establishment
X.25 dial access: dialing procedure running now
System error
Notes:
X
The diagnostic indication will be used by the above shown packet.
The diagnostic indication will not be used by the above showed packet.
PVC The above showed packet will use this diagnostic indication only with PVC
(Permanent Virtual Call).
X.75 The diagnostic indication will be used with international connections.
*)
Only valid for special network components (concentrator).
84
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
5.4.3 X.25 causes in Restart packet
Coding of the field "Reason for Restart" in the packet "Indicate-Restart".
01
03
07
Local sequence error
Temporarily disturbance in the network
Network ready
5.4.4 X.25 causes in Reset packet
00
01
03
05
07
09
0F
11
Triggered by DTE
Out of operation (virtual connections only)
Remote sequence error
Local sequence error
Temporarily network disturbance
Remote station ready (virtual connections only)
Network ready (virtual connections only)
Incompatible destination
© Stollmann Entwicklungs- und Vertriebs-GmbH
85
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
5.5 CAPI causes and their explanation
Coding of the CAPI cause in hexadecimal form.
0000
0001
0002
0003
No error
NCPI ignored
Flags ignored
Alert already sent
1001
1002
1003
1004
1005
1006
1007
1008
100a
100b
1101
1102
1103
1104
1105
1106
1107
1108
1109
Too many applications
Logical block size too small
Buffer exceeds 64k
Message buffer size too small
Too many logical connections
Reserved1
Message could not be accepted
Register OS Resource Error
External Equipment not supported
External Equipment only
Bad application ID
Illegal cmd or message length
Message queue full
Message queue empty
Message lost
Unknown notification
Message not accepted
OS Resource Error
CAPI not installed
2001
2002
2003
2004
2005
2006
2007
Bad State
Illegal Identifier
Out of PLCI
Out of NCCI
Out of LISTEN
Out of Fax Resources
Illegal Message Parameters
3001
3002
3003
3004
3005
3006
B1 protocol not supported
B2 protocol not supported
B3 protocol not supported
B1 protocol param not supported
B2 protocol param not supported
B3 protocol param not supported
86
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
3007
3008
3009
300a
300b
300c
300d
B Prot combination not supported
NCPI not supported
Unknown CIP value
Flags not supported
Facility not supported
Data length not supported
Reset procedure not supported
3301
3302
3303
3304
3311
3312
3313
3314
3315
3316
3317
3318
3319
Layer1 protocol error
Layer2 protocol error, i.e. DTE address not correct, TEI not correct
Layer3 protocol error
Another application got the call
Fax remote station is not fax
Fax training failed
Fax disconnect before transfer
Fax disconnect remote abort
Fax disconnect remote procedure
Fax disconnect local transmitter underrun
Fax disconnect local receiver overflow
Fax disconnect local abort
Fax illegal transmit data
34xx Error cause from the ISDN line, xx represents the ISDN cause (see page 78)
© Stollmann Entwicklungs- und Vertriebs-GmbH
87
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
5.6 Diagnostic using the internal Trace
For more sophisticated debugging an internal trace functionality is implemented.
This logging mechanism allows to write activities of the ISDN and the serial interface
into a wrap around buffer. The type of entries can be selected by a trace mask.
trcmsk
trcmsk par
set trace mask
Setup the mask to select the type of data to be written into the trace
buffer.
Default: D channel Layer 1 and 3, DTE interface lines, DTE-Data in
connection-setup and clearing-phase.
The parameter par has to be setup in the following way, all bytes have
to be entered (default 00 00 00 77 00 72 05 02):
par := bl1 bl2 bl3 dl1 dl2 dl3 sl1 app
bl1
reserved
00
bl2
B channel frames (layer 2) disabled
00 (default)
enable HDLC frames
03
bl3
B channel packets (layer 3) disabled 00 (default)
enable X.25 packets
03
dl1
D channel layer 1 status disabled
00
enable C/I codes and sttes
77 (default)
dl2
D channel LAPD frames disabled
00 (default)
enable HDLC frames
03
dl3
D channel layer 3 messages disabled 00
enable layer 3 messages
72 (default)
sl1
serial line trace disabled
00
enable serial trace
05 (default)
examples:
trcmsk 00000077007205 D channel layer-1 and layer-3, serial data and
status lines
trcmsk 00030000007205 D channel layer-3, B-channel layer-2,
serial data and status lines
trcmsk 00000300007205 D channel layer-3, B-channel layer-3,
serial data and status lines
88
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
trcclr
clear trace buffer
trcclr
clear actual trace buffer contents
trcread
trcread
read trace buffer
Output of the complete trace buffer in hexadecimal chars (ASCII, max.
line length 72 chars).
Every entry of the trace buffer is output using the following format:
Entry number – Timestamp – Type – Length – Databytes
Entry number
Timestamp
TypeAndSource
Length
Databytes
Sequence number of entry
in units of 10 ms
Source of trace entry:
bit0-7: type from trace mask
bit8-14: source of trace entry:
0200 : B channel layer 2 (bl2)
0500 : D channel layer 1 (dl1)
0600 : D channel layer 2 (dl2)
0700 : D channel layer 3 (dl3)
0900 : Serial status line / serial data
bit15: 0xxx : incoming event (from ISDN line)
8xxx : outgoing event (to ISDN line)
“FFFF“ : Reset for firmware
Length of following data bytes
Data bytes; continued lines are indicated by an “>“.
Coding of trace data bytes dependent of TypeAndSource:
The high order bit shows always the direction of the data:
0xxx = received data into the TA (from ISDN or serial)
8xxx = transmitted data by the TA (to ISDN or serial)
© Stollmann Entwicklungs- und Vertriebs-GmbH
89
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
0511/8511: D channel layer 1 status
0xF1 Inactive not used
0xF2 Sensing not used
0x F3 Deactivate
0x F4 Awaiting Signal
0x F5 Indentifying Input
0x F6 Synchronized
0x F7 Activated
0x F8 Lost Framing
90
0512:
D channel layer 1 C/I code (NT to TE)
0x00 Deactivation Request from F7/F8
0x01 Reset acknowlegde
0x02 Test mode acknowlegde
0x03 Slip detected
0x04 Signal received
0x05 Deactivation Request from F6
0x07 Power up
0x08 Activation request
0x0A Activation request loop
0x0B Illegal code violation
0x0C Activation indication priority 8
0x0D Activation indication priority 10
0x0E Activation indication loop
0x0F Deactivation confirmation
8512:
D channel layer 1 C/I code (TE to NT)
0x00 Timing
0x01 Reset
0x02 Test mode SSP
0x03 Test mode SCP
0x08 Activation request priority 8
0x09 Activation request priority 10
0x0A Activation request loop
0x0F Deactivation indication
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
0712/8712: D channel messages, coding refers to Q.931 and ETS
300102-1.
Coding of Message Type within D channel layer 3
message – 4th data byte in trace output:
Message
code (Hex)
Message name
01
ALERTING
02
CALL PROCEEDING
03
PROGRESS
05
SETUP
07
CONNECT
0D
SETUP ACKNOWLEDGE
0F
CONNECT KNOWLEDGE
20
USER INFORMATION
21
SUSPEND REJECT
22
RESUME REJECT
25
SUSPEND
26
RESUME
2D
SUSPEND ACKNOWLEDGE
2E
RESUME ACKNOWLEDGE
45
DISCONNECT
46
RESTART
4D
RELEASE
4E
RESTART ACKNOWLEDGE
5A
RELEASE COMPLETE
60
SEGMENT
75
STATUS ENQUIRY
79
CONGESTION CONTROL
7B
INFORMATION
7D
STATUS
7E
NOTIFY
0602/8602: D channel LAP-D frames, coding refers to Q.921
0904/8904: Serial line received / transmitted data by the TA+ in
© Stollmann Entwicklungs- und Vertriebs-GmbH
91
TA+POX, TA+HUX, TA+SOC User manual
5. Diagnostic and error messages
1.80D/09.2005
command phase (i.e. AT commands and responses).
0901:
Serial status lines
X
X
CTS
RTS
DCD
RI
DSR
DTR
0/1 0/1 0/1 0/1 0/1 0/1
The count of the received value is hexadecimal coded (0x NN).
An active level (ON) of the serial status line is signaled with
logical level “1”.
Example:
92
X
X
CTS
RTS
DCD
RI
-
-
0/1 0/1
ON ON
ON ON
ON ON
ON OFF
0/1
OFF
ON
OFF
OFF
0/1
OFF
OFF
OFF
OFF
DSR
DTR
0/1 0/1
ON ON
ON ON
ON ON
ON OFF
Hex coded result
0xNN
0x33
0x3B
0x33
0x22
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
6 Appendix
A1:
Technical data TA+POX, TA+HUX, TA+SOC
TA+POX serial interface:
functional:
electrical:
mechanical:
V.24
V.28
9 pin DSUB connector (female)
TA+HUX serial interface:
functional:
electrical:
mechanical:
V.24
TTL
double pin rows P1
TA+SOC serial interface:
functional:
electrical:
mechanical:
V.24
TTL
single pin rows X4
Transmission speeds:
DTE:
B channel:
300 – 230400 bit/s (asynchronous)
2 x 64000 bit/s (synchronous)
Character representation:
Character synchronization:
Operating mode:
8Bit no Parity, 1 stop bit
7Bit even/odd Parity, 1 stop bit
asynchronous
half duplex or full duplex
ISDN interface:
TA+POX mechanical:
TA+HUX mechanical:
TA+SOC mechanical:
S bus interface according to ITU I.430
build in RJ45 plug
double pin rows P2
single pin rows X3
Physical dimensions:
TA+POX:
TA+HUX:
TA+SOC:
desktop casing: 71 x 22 x 123 mm (WxHxD)
plug on module: 56 x 56 x 12 (8) mm (WxHxD)
plug on module: 64,5 x 26,5 x 14 mm (WxHxD)
Power supply:
TA+POX:
TA+HUX:
TA+SOC:
external power supply 5V DC.
5V DC (3,3V DC)∀5%, via double pin row P2
3,3V DC ∀5%, via single pin row X5
© Stollmann Entwicklungs- und Vertriebs-GmbH
93
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
A2:
1.80D/09.2005
LED displays TA+POX
Active states:
L1
L2
⊗
Θ (1x1s)
⊗
⊗
⊗
⊗
Θ (2sec)
O
O
∅
⊕
⊗
B1, B2
O
⊗
Error states:
L1
L2
O
Θ
O
Θ
O
O
Θ (nx1s)
Θ
Status
Power-On-Phase ; Wait
ISDN not ok
; Check ISDN interface/ -connector
Active phase
; ISDN ok, no ISDN connection established
Call active
; ISDN Connection will be established
Synch active
; Waiting for B channel synchronization
Connected
; Data connection is established
Status B channels
B channel offline
;
B channel online
; ISDN connection established
Status
TA+POX not ok ; Hardware error, TA+POX repair necessary
ISDN not ok
; Check ISDN interface/ -connector
TA+POX not ok ; Hardware error, TA+POX repair necessary
B1, B2 flashing: Bootloader active, no operational firmware
programmed. Use command at**flash to
download firmware with 115200 Bd,N81
(see page 75).
LED Legend:
⊗
∅
⊕
Θ
O
94
On
occ
short on, long off
Cycle 1 sec
fl
long on, short off
Cycle 1 sec
(nxms)
continuous blinking: n times every m seconds
Off
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
A3:
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
TA+HUX V3 Mechanical dimensions of the module V3
.
© Stollmann Entwicklungs- und Vertriebs-GmbH
95
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
A4:
TA+HUX V3 Serial Interface Connector P1
P1-Pin
Signal
1
GND
2
VCC
3
4
5
6
7
8
9
10
11
12
13
GND
TXD~
GND
RXD~
ID2
RTS~
ID1
CTS~
RESET~
DTR~
L3
O
O
I
O
O
I
I
O
14
15
16
17
DCD~
RI~
DSR~
UA
18
19
20
Outputs:
UA:
L3:
UA2:
Inputs:
UE:
UE2:
96
1.80D/09.2005
Direction TA usage
from TA
I
0V-Power
GND
External
interfacing
0V
Power
supply
+5V
Power
supply
GND
GND
GND
GND on TA+HUX
NC or READ
10k Pull up on TA+HUX
NC or READ
RESET active low (OC)
NC
(internal 10k Pull up)
NC
info
O
O
O
O
User Output 1
UE~
UA2
I
O
User Input 1
User Output 2
UE2
I
User Input 2
NC or status
info
10k Pull up
NC or status
info
NC, reserved
I
+5V-Power
I
or
status
default: similar to L1 of TA+POX (ON : ISDN activated, else
OFF)
default: equals L3+L4 of TA+POX: one or both B channel
occupied: B channel(s) connected, but may be not
synchronized.
reserved
reserved
reserved
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
A5:
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
TA+HUX V3 ISDN interface connector P2
P2-Pin
1
2
3
4
5
Signal
RXTXRX+
TX+
RX (BRA-power
supply)
TX (BRA-power
supply)
6
A6:
Direction
I
O
I
O
O
RJ-45-Pin
5
6
4
3
NC
O
NC
TA+HUX V3 IOM Interface connector P3
P3-Pin
Signal
1
2
3
4
5
6
DD
DU
FSC
DCL
SDS
BCL
Direction from
TA usage
TA
O
IOM Data downstream
I
IOM Data upstream
O
IOM frame sync
O
IOM double bit clock
O
IOM B channel strobe
O
IOM bit clock
© Stollmann Entwicklungs- und Vertriebs-GmbH
97
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
A7:
98
1.80D/09.2005
TA+SOC V2 Mechanical dimensions of the module
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
A8:
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
TA+SOC V2 connector X1 to X6
Pin
Con Signal
Dir. active TA+SOC usage
1
2
3
4
X3
X3
X3
X3
TX+
TXRXRX+
O
O
I
I
ISDN Transmit +, RJ45 jack Pin 3
ISDN Transmit -, RJ45 jack Pin 6
ISDN Receive -, RJ45 jack Pin 4
ISDN Receive +, RJ45 jack Pin 5
14
15
16
17
18
19
IOM
IOM
IOM
IOM
IOM
IOM
BCL
DU
DD
FSC
DCL
SDS
O*
I*
O*
O*
O
O
IOM Bit clock, LT-S-Mode: Input
IOM data upstream, LT-S-Mode: Output
IOM data downstream, LT-S-Mode: Input
IOM Frame sync, LT-S-Mode: Input
IOM Double bit clock
IOM channel strobe
24
25
26
27
28
29
30
31
32
X1
X1
X1
X1
X1
X1
X1
X1
X1
RESET~
nc
GND
UA
L3
nc
UA2
UE
UE1
I
L
Reset, may be left open
O
O
H
H
GND (Signal)
To connect to LED1
To connect to LED2
O
I
I
H
H
H
General purpose Output
General purpose Input
General purpose Input
33
34
35
36
37
38
39
40
41
X4
X4
X4
X4
X4
X4
X4
X4
X4
RTS~
RXD
TXD
RI~
DSR~
CTS~
DCD~
DTR~
GND
I
O
I
O
O
O
O
I
L
H
H
L
L
L
L
L
Request to Send
Receive Data
Transmit Data
Ring Indicator
Data Set Ready
Clear to Send
Data Carrier Detect
Data Terminal Ready
GND (Signal)
61
62
63
64
X5
X5
X5
X5
VCC
nc
GND
nc
I
+3.3V (Power Supply)
GND (Supply)
nc = not connected, do not connect to any signal.
© Stollmann Entwicklungs- und Vertriebs-GmbH
99
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
1.80D/09.2005
A9: TA+POX Pinout of the ISDN connector
Pinout of the 8 pin ISDN S-interface connector (RJ45) (ITU I.430/ISO 8877)
Pin
1
2
3
4
5
6
7
8
Signal (S bus)
Not connected
Not connected
Tx+ (Transmit +)
Rx+ (Receive +)
Rx- (Receive -)
Tx- (Transmit -)
Not connected
Not connected
A10: TA+POX Pinout of the V.24/V.28 interface (DSUB 9)
Pin
V.24/V.28
ITU
I/O
DIN
TEXT
EIA
1
109
M5
DCD
O
Data carrier detect
2
104
D2
RD
O
Receive data
3
103
D1
TD
I
Transmit data
4
108/1
108/2
S1.1
S1.2
DTR
I
Data terminal ready
5
102
E2
GND
---
Signal ground
6
107
M1
DSR
O
Data set ready
7
105
S2
RTS
I
Request to send
8
106
M2
CTS
O
Clear to send
9
125
M3
RI
O
Ring indicator
100
© Stollmann Entwicklungs- und Vertriebs-GmbH
1.80D/09.2005
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
A11: TA+POX Cable layout for connection of terminals with 25 pin connectors
(male or female)
Only the cable with a male plug at the terminal side is shown. The pin configuration
for the female plug is the same.
V.24 device
TA+POX
1
shield *
5
SGND
102
5
2
TD
103
3
3
RD
104
2
4
RTS
105
7
5
CTS
106
8
6
DSR
107
6
20
DTR
108
4
8
DCD
109
1
22
RI
125
9
25 pin jack
Attention:
9 pin jack
allowed cable length < 15m.
for transmission speeds > 19.200 bit/s < 2m.
* necessary if cable length > 2m
© Stollmann Entwicklungs- und Vertriebs-GmbH
101
TA+POX, TA+HUX, TA+SOC User manual
6. Appendix
1.80D/09.2005
A12: TA+POX Cable layout to connect a PC with 9 pin male plug through a
serial COM-port
PC
TA+POX
shield *
5
SGND
102
5
3
TD
103
3
2
RD
104
2
7
RTS
105
7
8
CTS
106
8
6
DSR
107
6
4
DTR
108
4
1
DCD
109
1
9
RI
125
9
9 pin jack
Attention:
102
9 pin jack
allowed cable length < 15m.
for transmission speeds > 19.200 bit/s < 2m.
* necessary if cable length > 2m
© Stollmann Entwicklungs- und Vertriebs-GmbH
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement