NURIT 8000 User Manual - 1st National Payment Solutions

NURIT 8000 User Manual - 1st National Payment Solutions
Users Guide
.
NURIT 8000
Secure
Quick Service Payment
Functionality
User Guide
APPLICATION
POS_STD
POS_PLUS
VERSION 4_82
Wireless
Palmtop
Solution
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Product Information
FCC COMPLIANCE
STATEMENT
EUROPEAN UNION
DIRECTIVES
CONFORMANCE
STATEMENT
WARNING!
NOTICE
Manufacturer: Lipman Electronic Engineering Ltd.
Model: NURIT 8000 Secure
This product is in conformance with the requirements of applicable EU
Council Directives.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
The information contained in this publication is for informational purposes only and
subject to change without notice. It does not represent a commitment on the part of
Lipman USA Inc. or Lipman Electronic Engineering Ltd.
No part of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated to any language in any form by any means without the
prior written permission of Lipman.
Copyright © 1998 by Lipman Electronic Engineering Ltd. All rights reserved.
TRADEMARKS Trademarks and trade names contained in this document belong to their respective
companies.
LIPMAN USA INC.
March 2004
50 Gordon Drive
Original
Syosset, NY 11791
Publication No.
Tel: (1) 516-484-9898 Fax: (1) 516-484-9057
E-mail: Sales@LipmanUSA.com
Installation Guide
2
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Product Regulatory Information
FCC PART 15
REQUIREMENTS
This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment and the receiver.
x Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
x Consult your dealer or an experienced technician for help.
Connection of peripherals to this unit requires the use of grounded, shielded
cables to ensure compliance with the class B limits.
FCC PART 68
REQUIREMENTS
[APPLICABLE WHEN
USING OPTIONAL
NURIT 8000
SECURE DOCKING
STATION OR NURIT
8000 EXTERNAL
MODEM]
The Federal Communications Commission (FCC) has established rules
permitting this device to be directly connected to the telephone network.
Standardized FCC Part 68 compliant telephone line cords and modular
jacks are used for these connections. This equipment should not be used
on party or coin lines.
If this device is malfunctioning, it may be causing harm to the telephone
network; this device should be disconnected until the source of the problem
can be determined and until repair has been made. If this is not done, the
telephone company may temporarily disconnect service.
The telephone company may make changes in its technical operations and
procedures; if such changes affect the compatibility or use of this device,
the telephone company is required to give adequate notice of the changes.
You will be advised to file a complaint with the FCC.
If the telephone company requests information on what equipment is
connected to their lines, inform them of:
x The telephone number this unit is connected to
x The ringer equivalence number: 0.2A
x The USOC jack required: RJ-11C
x The FCC Registration number:
The Ringer Equivalence Number (REN) is used to determine how many
devices can be connected to your telephone line. In most areas, the sum of
the RENs of all devices on any one line should not exceed five (5). If too
many devices are attached, they may not ring properly. To be certain of the
number of devices that may be connected to the line, as determined by the
total RENs, contact the telephone company to determine the maximum REN
for the calling area.
Continued on next page
Installation Guide
3
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Product Regulatory Information, Continued
FCC PART 90
REQUIREMENTS
This device contains a radio transceiver module, (FCC ID number is
located on the bottom of the terminal), operating under Part 90 of the FCC
rules in a licensed part of the radio spectrum. Qualified personnel must
perform service or repairs to the radio portion of this device. Any
unauthorized modification to the radio module, shielding, or antenna
system may void the user’s authority to operate this device
IN CANADA
This digital apparatus does not exceed the class B limits for radio noise
emissions from digital apparatuses set forth in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère de Communications du Canada.
SHIPPING
Carefully pack and send the package prepaid, adequately insured and
preferably in the original carton. Attach a postage-paid letter to the
outside of the package detailing the complaint.
PLEASE NOTE: SHIPMENT MUST BE SENT TO AN AUTHORIZED
DEALER OR SERVICE CENTER ONLY. PLEASE NOTIFY YOUR
LIPMAN REPRESENTATIVE BEFORE SHIPMENT. PRODUCTS SENT
TO OTHER LOCATIONS WILL BE RETURNED AT OWNERS
EXPENSE. CONTACT YOUR DEALER FOR THE CORRECT
ADDRESS.
Installation Guide
4
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
LIPMAN USA - NURIT 8000 SECURE - Limited Warranty
Lipman USA Inc. will repair this product with new or rebuilt parts, free of charge, in the U.S.A. for
one (1) year from the date of original purchase in the event of a defect in materials or workmanship.
Carry-in or mail-in service in the continental U.S.A. can be obtained during the warranty period from
our N.Y. Service Center or call 1-800-4-LIPMAN toll free. In New York State call (516) 484-9898.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of
original purchase will be required in order to exercise your rights under this warranty.
This warranty only covers failures due to defects in materials or workmanship which occur during
normal use. It does not cover damage which occurs in shipment; failures which are caused by
products not supplied by Lipman USA; or failures which result from accident, misuse, abuse, neglect,
mishandling, misapplication, alteration or modification; service by anyone other than the Lipman USA
Service Center or accredited service centers, or damage that is attributable to acts of God.
Limits and Exclusions
There are no express warranties except as listed above.
LIPMAN USA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS
WARRANTY. ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, therefore some of the above exclusions or
limitations may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state.
If a problem with this product develops during or after the warranty period, you may contact your
dealer or Service Center. If the problem is not handled to your satisfaction, then write to:
LIPMAN USA INC., 50 Gordon Drive, Syosset, N.Y. 11791
E-mail: NURITsys@lipmanusa.com
Tel: (516)-484-9898 FAX: (516)-484-9057.
Installation Guide
5
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
General and Safety Instructions
SECTION
DESCRIPTION
When using this NURIT Wireless POS EDC Terminal or any equipment or
accessories associated with it operation, basic safety precautions as below
should always be followed to reduce the risk of fire, electric shock, or
personal injury.
The following safety instructions are based in general on those provided by
Underwriters Laboratories Inc. U.S.A.
1.
Read and understand all instructions.
2.
Follow all warnings and instructions marked on the unit.
3.
Unplug the unit from wall outlets before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning and/or a soft brush.
4.
Do not use the unit near water when using the AC charger or external modem.
5.
Place the unit on a stable surface when operated in a fixed location. When operated
hand-held, be sure to grasp the unit securely. Serious damage may result if the unit
falls.
6.
Do not cover slots and openings of the unit. They are provided for ventilation and
protection against overheating. Never place the unit near radiators, or in a place
where proper ventilation is not provided.
7.
Use only the power source as marked on the unit. If you are not sure of the type of
the power supplied to your home, consult your dealer or local Power Company.
8.
Do not place objects on the power cord. Install the unit where no one can step on
the cord.
9.
Do not overload wall outlets and extension cords as this can result in the risk of fire
or electric shock.
10.
Never push any objects into this unit through slots (other than those specifically
meant for credit, debit or smart cards) as they may result in risk of fire or electric
shock. Never spill any liquid on the unit.
11.
To reduce the risk of electric shock, do not disassemble any of the equipment or
accessories referred to in this manual. If required, take the equipment to a qualified
serviceperson. Opening or removing covers may expose you to dangerous voltages
or other risks. Incorrect re-assembly can cause electric shock.
Continued on next page
Installation Guide
6
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
General and Safety Instructions, Continued
Unplug this unit from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
ƒ When the charger cord or plug is damaged or frayed.
ƒ Liquid has been spilled into the unit.
12.
ƒ Unit has been exposed to rain or water.
ƒ Unit does not work normally, when following the operating instructions.
ƒ Unit has been dropped or damaged.
ƒ Unit exhibits a distinct change in performance.
13.
During thunderstorms, disconnect telephone line, if possible. There may be a
remote risk of electric shock from lightning*.
14.
Never install telephone wiring during a lightning storm*.
15.
Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations*.
16.
Never touch non-insulated telephone wires or terminals unless the telephone line
has been disconnected at the network interface*.
17.
Use caution when installing or modifying telephone lines*.
18.
When in the vicinity of a gas leak, do NOT use the NURIT 8000 SECURE, a standalone telephone or a telephone connected to a NURIT docking station to report
such a leakage.
* When using the NURIT 8000 SECURE optional docking station and/or external modem.
IN ADDITION TO THE ABOVE MENTIONED SAFETY INFORMATION, PLEASE NOTE THE FOLLOWING OPERATIONAL
SAFETY INSTRUCTIONS AND CAUTIONS!
Your NURIT 8000 SECURE contains a transmitter and receiver that emit radio frequency (RF)
energy. The actual frequency range used by the NURIT 8000 SECURE is radio-modem dependent
according to specific model. Digital modulation techniques are used. During radio communication, the
local radio system handling the actual communication controls the actual power transmission output
level. This output level may typically vary (relative to distance between user location and cell transmit
sites.)
Continued on next page
Installation Guide
7
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
General and Safety Instructions, Continued
POSITIONING
The most desired operational position for the terminal is hand-held at an
angle of approximately 30o. The unit is also obviously designed for
optimal tabletop usage. Try and keep the terminal a short distance from
your body.
When used properly, the design of this hand-held wireless terminal
complies with European and International standards for the protection of
public exposure to radio frequency (RF) magnetic signals.
MEDICAL
WARNING!
For those persons using a pacemaker or other medical devices please
read the following important safety notes!
Though most electronic equipment and critical medical devices are
shielded against radio-frequency signals, it is important to realize the
possibilities of potential interference and what standard precautions may
be taken.
PACEMAKERS
Industry standards recommend a minimum separation of 6 inches (15
cm) should be kept between a wireless phone-type device and a
pacemaker to prevent any potential problems.
Individuals using a pacemaker should:
1. Always keep the NURIT more than 6 inches (15 cm) from the
pacemaker when using the unit as a cellular phone or when
performing a transaction.
2. Turn the NURIT off immediately if you suspect any problem of
interference.
OTHER MEDICAL
TYPE DEVICES
Consult the manufacturer of your medical-type device to determine its
level of shielding. Note usage regulations in health facilities. Depending
on the proximity to certain equipment, you may be asked not to use your
NURIT terminal or one of its accessories.
OTHER
ELECTRONIC
DEVICES
Radio frequency energy may affect improperly installed or very
sensitive systems. Consult your vehicle manufacturer or air crew (for
possible airborne operation) respectively regarding typical problems that
may arise when using the NURIT. At the time of the publication of this
guide, it is known that all radio-type devices are prohibited to use
while airborne.
Continued on next page
Installation Guide
8
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
General and Safety Instructions, Continued
ADDITIONAL
WARNINGS!
CONVENTIONS
1.
Do not use your NURIT 8000 SECURE in an area of potential
explosive atmosphere e.g., fuel or chemical storage or transfer
facilities or any area that you would be advised to turn off your
vehicle’s engine. In addition, do NOT replace your battery pack or
charge your NURIT in an area of potential explosive atmosphere.
2.
Do NOT use your NURIT in a known blasting area.
3.
Do NOT place your NURIT in the area over a vehicle-equipped
air bag.
4.
If battery pack has been removed, ensure that no metal objects
come in contact with the pack’s electrical contacts.
5.
You are using a NURIT terminal designed for use with a built-in
internal antenna. Do NOT open the unit with the intent of
tampering with the antenna system. Doing so may damage the
unit and violate FCC (Ministry of Communications) regulations.
ƒNotes, cautions and warnings are used like this:
ƒ"Notes" contain helpful hints and other important information that
will help you get better use from your NURIT.
ƒ"Cautions" provide information about procedures that, if not
observed, could result in damage to the NURIT or other
equipment.
ƒ"Warnings” mean failure to follow specific procedures and
practices may result in personal injury.
NOTE
This publication could include technical or typographical errors. Changes
are periodically made to our publications; these changes will be
incorporated in future editions.
If you ship the product
Carefully pack and send the package prepaid, adequately
insured and preferably in the original carton. Attach a
postage-paid letter to the outside of the package detailing
the complaint.
PLEASE NOTE: SHIPMENT MUST BE SENT TO AN
AUTHORIZED DEALER OR SERVICE CENTER ONLY.
PRODUCTS SHIPPED TO OTHER LOCATIONS WILL
BE RETURNED AT OWNERS EXPENSE. CONTACT
YOUR DEALER FOR THE CORRECT ADDRESS.
Continued on next page
Installation Guide
9
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
General and Safety Instructions, Continued
For your future
reference
SERIAL NO.
DATE OF PURCHASE
__________________________
(found on the bottom of the unit)
_______________________
NAME OF DEALER
DEALER'S ADDRESS
_____________________________
_______________________
_______________________
_______________________
_____________________________
Important!
Appendix B of this manual is essential and therefore should be read carefully and
thoroughly prior to use of this product. (See page 175)
General Information
FOREWORD
Thank you for purchasing the NURIT 8000 Secure Wireless Palmtop
Transaction Terminal. You now own one of the most advanced
electronic point-of-sale (POS) devices manufactured today.
This manual explains basic installation instructions. To fully utilize the
features of your terminal, and for general safety purposes, take some
time to familiarize yourself with this manual, the terminal or any
accessories to be used.
Please store this manual in a safe place for future reference.
Installation Guide
10
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
NURIT 8000 SECURE - General Overview
Power
ƒTerminal power requirements (from
REQUIREMENTS
AC charger): 8.4 VDC at 1.0A
ƒAC charger requirements: 100-240 VAC at 60 Hz (U.S. standard) or;
100-240 VAC at 50 Hz (European standard)
Dimensions
TERMINAL
ƒ
Height: 82 mm (3.23 in.)
ƒ
Width: 108 mm (4.26 in.)
ƒ
Depth: 230 mm (9.06 in.)
ƒ
57mm (2.25 in.) x 38 mm (1.5 in.)
ƒ
[10.5 mm (0.4 in.) core diameter]
PAPER ROLL
Weight
ƒ 650g (1.4 lb.)
TERMINAL
* NOTE
Specifications are subject to change in the interest of technological
improvement, without notice or obligation.
Technical
Assistance
Contact your Lipman representative for technical assistance and
ordering information regarding specific components or accessories.
Installation Guide
11
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Installation Table of Contents
Installation
Unpacking Shipping Carton
Main Components
Optional Accessories
Hardware Features of the NURIT 8000 SECURE
Top View
Bottom View
About the Battery Pack
About the Battery Pack
Installing the Battery Pack
Removing the Battery Pack
Connecting the AC Charger
Installing Optional 33.6 Kbps External Modem
Installing the Vehicular Charger
Removing the Vehicular Charger
Installing the Paper Roll
Installing the Keypad Cover
Removing the Keypad Cover
Using the Magnetic Card Reader
Using the Smart Card Reader
Installing the GSM Subscriber Identity Module (SIM) Card
Connecting Typical Peripheral Device
Using an Optional Cellular Headset
Infrared (IrDA) Communication Link
General Care & Maintenance
An Overview of the NURIT 8000 SECURE
The Terminal Keyboard
Powering the unit On and Off
Installation Guide
13
14
14
15
16
16
16
17
17
17
18
18
19
19
20
20
21
21
21
22
22
23
23
24
24
25
25
26
12
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Installation
SELECTING A
LOCATION
Select a location for the NURIT 8000 SECURE Hand-Held Wireless
terminal that is safe and convenient for both the retailer and cardholder.
CAUTION!
The NURIT 8000 SECURE is designed for indoor use when using the
unit’s AC charger, optional docking station or optional external modem.
The unit is designed to be operated outdoors, but should only be
powered by its built-in battery pack. Under no circumstances should the
unit be powered or charged outdoors using its AC charger or docking
station. Obviously, the NURIT 8000 SECURE should not be used in
areas of excessive moisture or heat.
Avoid areas with:
ƒ Excess heat, dust or other debris
ƒ Oil or moisture
WARNING!
When connected to the terminal’s AC charger, optional docking station
or external modem, do not use the terminal near water, including sink,
laundry tub or pool. In addition, avoid exposure to:
Devices that radiate excessive voltage fluctuations or electrical
noise, such as air conditioners, fans, electric motors, neon signs,
or high-frequency security devices.
Direct sunlight or objects that radiate heat.
Metal partitions or such obstructions that may disrupt radio
reception or transmission.
WARNING!
When not operated from its hand-held position, place the NURIT 8000
SECURE on a flat table or countertop. When used in conjunction with
its optional external modem or docking station, the terminal should be
conveniently located in relation to a telephone line and AC power outlet.
To meet standard ventilation requirements, at least 22.1 centimeters
(8.7 inches) of clear space must be provided around the terminal when
placed in its fixed operating location.
Installation Guide
13
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Unpacking Shipping Carton
When opening the original shipping carton, carefully inspect the contents for any damaged or
missing components. Lipman has taken all measures to provide you with a complete unit. If
shipping damage is evident, file a claim with the shipping company. Please notify your
Lipman distributor concerning this damage, and if any components are missing.
Instructions
Follow the steps below when unpacking the NURIT 8000 SECURE
terminal and its supplied accessories and/or options from carton:
Step
Action
1.
With the carton right side up, remove the carton’s outer sleeve.
2.
Open the carton and carefully remove the contents.
3.
Stop.
For your personal safety, do NOT use a NURIT terminal showing any signs of damage!
Note
Before actual use of the terminal, remove the thin
transparent plastic membrane that covers the LCD
screen.
Main Components
ITEM
Installation Guide
# 1.
NURIT 8000 SECURE Terminal
# 2.
AC Charger
# 3.
Paper Roll Spindle
# 4.
Lithium-ion Battery Pack
# 5.
Keypad Cover
# 6.
Thermal Paper Roll
# 7.
Documentation Kit.
14
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Optional Accessories
# 1.
Docking Station
# 2.
PC-Terminal Download Cable, (Cat. No. FCL09503.)
# 3.
Keyboard Emulation Barcode Reader Adapter Cable
(Cat. No. FCL09506.)
# 4.
Terminal-to-Terminal (peer-to-peer) Interconnection
Cable, (Cat. No FCL09505.)
# 5.
External Modem
# 6.
Hands-Free Headset (2.5 mm plug)
cellular dealer for purchasing details)
# 7.
Cigarette Lighter Vehicular Charger
# 8.
Touch Screen Stylus
# 9.
Standard RS-232 Barcode Reader Adapter Cable
(Cat. No. FCL09504.)
(contact your
Availability of accessories or options may vary according to customer requirements. At the
publication time of this manual, some items may not yet be available. Consult your Lipman
representative for details regarding these and any upcoming options. Connection of any nonLipman-approved accessory may cause damage and thus void the Limited Warranty of this
equipment.
Installation Guide
15
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Hardware Features of the NURIT 8000 SECURE
Take a few moments to familiarize yourself with the terminal’s main feature locators as
depicted in the following illustrations.
Top View
# 1.
Thermal Paper (Receipt)
# 2.
Paper Roll Cover
# 3.
Paper Cover Release Button
# 4.
Graphical Display (Touch Display, Optional)
# 5.
Magnetic Card Reader
# 6.
Keypad
# 7.
Keypad Cover
# 8.
Smart Card Reader
# 9.
IrDA Window
# 10.
Battery Charge Connector
# 11.
Data Connector
# 12.
Headset Connector
# 1.
Rubber Stop
# 2.
Radio-Modem Info. Label
# 3.
Model/Barcode-Serial No. Label
# 4.
Compliance Label
# 5.
Battery Pack
# 6.
Battery Pack Removal Snap
# 7.
Docking Station Connector Cover or Connector
(Model Dependent)
Bottom View
Installation Guide
16
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
About the Battery Pack
SMART LITHIUMION BATTERY
PACK
The supplied high-performance Lithium-ion battery pack provides 7.2
VDC at 1450 mAh of capacity. When fully discharged, the battery fully
recharges within 3 hours while installed in the terminal. An 80% charge
capacity is reached within 1 hour. The terminal can be left connected to
its AC charger indefinitely without causing damage to the battery.
Under typical use, the battery pack is good for well over 500 charge
cycles, after which operating time may very slowly decrease. This
battery pack has a self-discharge rate, and without normal use will lose
approximately 1% of it charge per day. Replace the battery pack with a
new one when the charge capacity is too weak for normal operation. If
for any reason you intend not to use your NURIT 8000 SECURE for an
extended period of time, remove the battery pack located on the
underside of the unit.
CAUTION!
When using the Lipman-supplied AC charger, the Lithium-ion battery
pack must be installed in the terminal.
WARNING!
1.
Please do NOT dispose of the battery pack in a fire! Dispose of
use batteries in accordance with local recycling regulations.
2.
If for any reason you intend to remove the NURIT’s battery pack,
make sure that the metal contacts do not come in contact with any
metal objects.
Extreme temperatures will degrade the performance of your battery
pack. Do not store this Lithium-ion battery pack in an ambient
temperature range below -20oC (4oF) and above 60oC (140oF ).
NOTE
Installing the Battery Pack
INSTRUCTION
Use the following step/action table when installing the battery pack:
Step
Action
Step 1
1.
Carefully invert the terminal. The terminal can be held in hand
or gently placed on a soft sponge-like surface so as not to
damage the unit’s LCD screen.
2.
Insert the battery pack onto the back of the terminal. Note that
the side of the pack with the arrow engraved on it should face
upward. The insertion is easily done by sliding the 2 tabs in
the front of the pack into the 2 openings on the front wall of
the battery compartment
3.
Press down on the battery pack until it snaps into place
4.
Stop.
Installation Guide
Step 2
Î
17
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Removing the Battery Pack
INSTRUCTION
Use the following step/action table when removing the battery pack:
Step
Action
1.
Hold the terminal in hand or gently place the unit on a
soft sponge-like surface in order not to damage the LCD
screen.
2.
Remove the battery pack from the back of the unit by
grasping the pack’s locking snap with a finger or
ballpoint pen.
3.
Lift the pack away from the unit.
4.
Stop.
Step 1
Î
Step 2
Î
Connecting the AC Charger
INSTRUCTION
The NURIT 8000 SECURE can be operated from an AC wall outlet by using
the supplied AC charger. Use the following step/action table for assistance.
Step
Action
1.
Plug the connector at the end of the adapter cord into the “power” port
on the left side of the NURIT’s front panel.
2.
Plug the AC charger into an electrical outlet.
3.
Stop.
Note: When the charger’s LED indicator light is green; the battery is on trickle charge. The
LED light is red when charging (battery is less than 98% changed). If LED indicator is
not illuminated, the charger is disconnected from the wall outlet.
Installation Guide
18
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Installing Optional 33.6 Kbps External Modem
INSTRUCTION
The optional 33.6 Kbps external fast modem (other baud rates available)
enables downloading desired applications and parameters to the NURIT
8000 SECURE via a standard telephone line. Use the following
step/action table for assistance.
Step
Action
1.
Insert the modem’s data plug into the center “data” port on the front of
the NURIT
2.
Connect a standard telephone line cord from the modem to a standard
telephone company line socket.
3.
Stop.
Installing the Vehicular Charger
INSTRUCTION
The Vehicular Battery Charger provides power to the NURIT 8000
SECURE and charges the built-in Lithium-ion battery pack. Use the
following step/action table for assistance.
Step
Action
1.
Insert the plug at the end of the charger’s cord into the “power” port on
the left side of the NURIT’s front panel.
2.
Remove the cigarette lighter from your vehicle’s cigarette lighter socket.
3.
Plug the charger’s adapter into the cigarette lighter socket.
4.
Stop.
Installation Guide
19
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Removing the Vehicular Charger
INSTRUCTION
Use the following step/action table for assistance with removal.
Step
Action
1.
Unplug the adapter from the cigarette lighter socket.
2.
Grasp the plug end of the charger’s cord and pull it out of the NURIT’s
“power” port.
3.
Stop.
Installing the Paper Roll
INSTRUCTION
Before you can process any transaction that requires a receipt, you must
install a paper roll into the printer compartment. To install this roll, use the
following step/action table.
Step
Action
1.
Place the terminal preferably on a flat surface.
2.
Open paper roll cover by pushing the release button in the
direction of the arrow appearing on it.
3.
Open the cover.
4.
Remove the paper roll spindle from the paper roll
compartment and insert it into the new paper roll.
5.
While holding the roll in hand, mount it together with its
spindle in place into the 2 slots on both sides of the
compartment. Ensure that the paper roll feeds from the
bottom!
6.
Approximately 1 inch (2.5 cm) of paper should extend out of
the paper roll compartment (between the cover and
serrated tear strip.)
7.
Press down on the front of the paper cover until it snaps in
place.
8.
Stop.
Installation Guide
20
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Installing the Keypad Cover
Use the following step/action table for assistance installing the keypad
cover.
INSTRUCTION
Step
Action
1.
Position the tabs on the inner front sides of the cover over the
indentations on both sides of the NURIT (on both sides of the keypad.)
2.
Press down on the cover until it snaps in place.
3.
Stop.
Removing the Keypad Cover
INSTRUCTION
Step
Use the following step/action table for assistance removing the
keypad cover.
Action
1.
Hold the NURIT securely with one hand.
2.
Grasp the cover with your other hand and lift upward.
The cover will easily unsnap from the terminal.
3.
Stop.
Using the Magnetic Card Reader
INSTRUCTION
A magnetic swipe card reader is located between the terminal’s
LCD screen and paper cover release button.
Step
Action
1.
Grasp the card so that its magnetic stripe is facing
you.
2.
Place the card into one end of the card reader
groove.
3.
Swipe the card in a smooth continuous manner.
This can be done in any direction desired (left-toright or right-to-left).
4.
Stop.
Installation Guide
21
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Using the Smart Card Reader
INSTRUCTION
Refer to the following action for assistance using the smart card reader.
Action
Insert the smart card (chip end first) into the
opening of the reader on the terminal’s front
panel. For guidance, most smart cards will
have directional guide arrows engraved or
inscribed on the cards.
Installing the GSM Subscriber Identity Module (SIM) Card
CAUTION!
The SIM card contacts can be easily damaged. Do not bend or scratch
when installing or removing the card.
NOTE
If you are not using a GSM radio modem, an optional Security Access
Module (SAM) may be installed instead of the SIM card used. The NURIT
8000 SECURE can house up to 2 optional SAM modules.
INSTRUCTION
The SIM card supplied by your GSM Cellular Service Provider is a special
card containing your telephone number, specific service details and
memory for storing telephone and messages. Your NURIT terminal can
NOT receive or make calls without the SIM card installed. Use the
following step/action table for assistance.
Step
Action
1.
Grasp the battery pack snap and lift upward.
2.
Open the SIM reader holder by pushing it in the direction of the
arrow engraved on it (towards you) and lifting the hinged holder
upward.
3.
Hold the SIM card so that its chip side is facing down towards the
contacts on the reader.
4.
Insert the SIM card into the grooves on each side of the holder.
Make sure that you slide the end closest to the chip into the
grooves of the holder first.
5.
Close the SIM cardholder and lock it by pushing it towards the
front of the battery pack compartment.
6.
Replace the battery pack on the back of the NURIT. Press down
on the pack to lock it in place.
Installation Guide
22
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Connecting Typical Peripheral Device
INSTRUCTION
Numerous peripheral devices can be used with the NURIT 8000 SECURE
terminal. A barcode reader is one such typical device. An interconnection
explanation and illustration appear below for a Keyboard Emulation
Barcode Reader.
Step
Action
1.
Connect the Barcode Reader to appropriate end of
the optional adapter cable (part no. FCL09506).
2.
Insert the other end of the adapter cable into the
center “data” port on the unit’s front panel.
Using an Optional Cellular Headset
INSTRUCTION
An optional headset may be used with NURIT 8000 models adapted for
cellular telephone communication.
Action
To use the headset, insert its plug into the
“stereo-type” port on the right side of the unit’s
front panel. When removing the headset from
the panel, make sure to grasp the plug and
not the cord.
Installation Guide
23
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Infrared (IrDA) Communication Link
INSTRUCTION
Your NURIT 8000 SECURE (model dependent) is capable of
communicating via an infrared communication link.
Action
In order to communicate, the infrared windows
of both units must be directed towards each
other. Typically, these units can be 2 NURIT
8000 SECURE terminals or a terminal and
personal computer.
The distance between units should not exceed
11.8 inch (30cm).
General Care & Maintenance
INSTRUCTION
The NURIT 8000 SECURE has been designed to give you long and
trouble-free service with minimal operator care. The user should protect
the terminal from direct sunlight, extreme heat, dampness and dust.
CAUTION!
Never use thinners, benzene and synthetic cleansers since they may
distort or damage the plastic and critical parts.
CLEANING THE
TERMINAL
For normal cleaning, gently wife off dirt from the body of the terminal with
a soft, damp, lint-free cloth. A very mild dishwashing detergent can be
used to dampen the cloth. Alcohol or alcohol-based cleansers may also
be used for more difficult stains. If available, a low-pressured blower
can be used to remove dirt accumulated around the keypad buttons and
within the paper roll compartment.
If possible, use a lens blower to remove dust and dirt from the LCD
screen. When so necessary, gently wipe the screen with a soft cloth or
eyeglass lens wiper.
CAUTION!
Never rub or strongly press on the LCD screen. Doing so may lead to
damage or other possible problems.
Installation Guide
24
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
An Overview of the NURIT 8000 SECURE
INFORMATION
This section will provide you with a basic understanding of the operations
and functionality of the NURIT 8000 SECURE. This will include a keyboard
overview and a basic explanation of common terms that you will find
throughout this manual.
The Terminal Keyboard
Key
[Back Arrow – ON/OFF]
[F]
(Function Key)
[MENU/CANCEL]
[CLEAR]
[NUMBER PAD]
[ALPHA]
[] And []
[ENTER]
Installation Guide
Function
Use this key to power the terminal On and Off and as a
Back Space when entering data.
Use this key to batch the terminal in addition to
accessing other convenient hot keys.
Use this key to access the terminal’s main menus and
sub-menus.
This key will clear entered data.
Used to enter all numeric values. In addition these keys
are used in conjunction with the Alpha key to input
alphabet text and various symbols.
This key converts the numbers on the keypad to their
corresponding letters.
Use these arrow keys to scroll through the menu and
submenu options.
Use this key to make selections.
25
APPLICATION POS_STD AND POS_PLUS – QSP – VER. 4_82
NURIT 8000 SECURE
Powering the unit On and Off
Instruction
Use the following steps to power the unit on and off. The terminal can be
powered on and off when on AC power and battery pack.
To Power On:
x Press the [ON/OFF] Button.
To Power Off:
x Press the [F] button and the [ON/OFF] buttons simultaneously
Installation Guide
26
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
User Guide Table of Contents
INTRODUCTION
1
RETAIL - User Operations
Processing Sale Transactions
Credit Cards
Debit Cards
EBT Cards
(Electronic Benefits Transfer)
Check Sale
Cash Sale
Processing Retail Sale Transactions – With Tip(s)
2
2
2
3
5
5
7
8
8
Voids
Void Sale
Void Return
Void Forced Sale
10
10
11
12
Returns
Credit Returns
Debit Return
Verify
Forced Transaction
Batching
Accessing Hot Keys
DL Verification General Report *
DL Verification Clerk Report *
DL Verification Supported States *
Clear Driver License Data *
13
13
14
15
16
17
18
21
22
23
24
Quick Service Payment
25
Menu Options
Accessing the Main Menu
29
29
1. Reports
Print the Default Report
Print the Current Report
Print History Reports
Display Transactions
Receipt Copy
Print the Performance Report
Tip Report
Report Set up – Printing Visa/MC Options
Report Setup – Tip Discount
RAM Disk Report
Communication Log Report
30
31
32
34
36
38
39
40
42
43
44
45
2. Merchant Parameters
Authorizations – TRANSACTION TYPE
Authorizations – Card Type
Authorizations – Debit Prompt
46
46
48
49
User Guide
1
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Security Levels
Edit Header/Trailer
Set Cash EDC
Setting the Merchant Fee
Set Batch Time
Server ID/Clerk ID/Invoice Mode
Site ID
51
52
54
55
56
58
60
3. Merchant Options
Paper Type
Buzzer Set
Operation Mode
Battery Saver
Prints Disclaimer
Set Menu Type
Set Halo
Set Halo
Print Setup
Store & Forward
Turning Store & Forward On/Off
Mode Select
Display Transactions
Reports – Store & Forward
Upload Transactions
Resend Failed Transactions
Delete Failed Transactions
Check Reader
Check Reader
Check Imager – Send Images (Bridge)
Check Imager – Send Images (FTP)
Check Imager – Clear Images
Check Imager – Clear Images
Check Imager – Setup Menu (Bridge)
Check Imager – Setup Menu (FTP)
Check Imager – Franking
Signature Option
Bridge Communication
Language Setup
61
61
62
63
64
66
67
68
68
70
71
71
72
75
77
79
80
81
82
82
83
85
86
87
88
89
95
96
97
98
4. Host Parameters
Host Parameters
Host Phones
Print EDC Setup
Protocol Version
AutoDial Setup
Host Radio Address
99
99
101
103
104
105
107
5. System Options
Set Terminal Time and Date
Edit PIN Key
Select Master Key Location
Set Batch Number
Edit Database
Edit Database – Void a Transaction
109
109
111
112
113
115
115
User Guide
2
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Database – Clearing the Database
Edit Database – CLEAR OFFLINE
Working Mode
Working Mode – TIP OPTIONS
Working Mode – AVS OPTIONS
Working Mode – Card Present Options
Working Mode – Comment Options
Predial Call
Pin Pad Initialization
Pin Pad Initialization
Pin Pad Function
Pin Pad Configuration
Status Bar
117
118
119
119
121
123
125
126
127
127
128
129
130
6. Radio Params
Radio Tests - RADIO RSSI
Radio Tests - TERMINAL MAN# (MOBITEX ONLY)
Radio Tests - Terminal LLI# (Motient Only)
Radio Tests - Radio Information
Radio Tests - Radio Information
Print Params
Battery Test
Battery Test
131
131
132
133
134
134
135
136
136
7. Download
Download Definitions
Downloading
Download – Communication Parameters, Phone
Download – Comm Parameters, Exchange Prefix
Download – Comm Parameters, Via>
Download – Comm Params, Baud Rate
Download – Comm Params, Dial>
Download – Comm Params, Gateway>
Download – Comm Params, Suffix
137
137
137
140
141
143
144
146
147
149
8. Communication
Minimum Retries
Dial: Tone/Pulse
Exchange Prefix
Gateway
Suffix
Via Line/Radio
CHECK LINE: ON
CHECK LINE: ON
151
151
152
153
154
155
156
157
158
Appendix A – Restaurant Tips and Tabs
Working Mode – TIP OPTIONS
Add Tips
Working Mode – Tab Option
Open a Tab
Close a Tab
Delete a Tab
Show Tabs
Tab Report
159
159
162
164
165
166
168
169
170
User Guide
3
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Open Tab Report
Close Tab Report
170
171
POS STD and PLUS - NURIT 8000 SECURE QUICK REFERENCE GUIDE
172
BASIC TROUBLESHOOTING
Appendix B - Lipman USA Licensing Agreement
174
175
177
Lipman USA Licensing Agreement, Continued
User Guide
4
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
INTRODUCTION
Presently, there are three varieties on the 4.82 Application. They include:
INFORMATION
- SCA_STD (for script)
- POS_STD (this version is supported in NURIT models 2085 and higher)
- POS_PLUS (this version is supported in NURIT 2085-M21, NURIT 3020,
NURIT 8320 and NURIT 8000 terminals The major difference between
POS_STD and POS_Plus is that Plus supports Magtek in addition to
signature capture, RDM, multi-language, the Communication Log
Report and the RAM Disk Report. Driver License Verification is
supported by application version POS7PLUS only.)
APPLICATION
NURIT MODEL
POS7_STD **
NURIT 2085, NURIT 3010, NURIT 3020, NURIT 8000 SECURE AND NURIT
8320
** REQUIRES NURIT OPERATING SYSTEM (NOS) 7.8.4 AND ABOVE.
PLEASE NOTE: For Merchants requiring PLUS Features, see the information in the following
chart.
APPLICATION
POS6PLUS *
POS7PLUS **
NURIT MODEL
NURIT 2085-M21 AND NURIT 3020
* REQUIRES NURIT OPERATING SYSTEM (NOS) 6.00 AND ABOVE.
NURIT 2085-M21, NURIT 3020, NURIT 8000 SECURE AND NURIT 8320
** REQUIRES NURIT OPERATING SYSTEM (NOS) 7.8.4 AND ABOVE.
PLEASE NOTE: The Nurit Control Center version must 7.4.11 or higher when building terminal
files with any of these application versions.
User Guide
1
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
RETAIL - User Operations
INFORMATION
This section explains the various instructions required in operating a NURIT
terminal. In this manual, transactions, operations, and specific functions available
with the POS_STD and POS_PLUS applications are explained. Screen displays
are typical of the NURIT 8000 SECURE terminal.
Processing Sale Transactions
Credit Cards
STEP
ACTION
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
1.
Be sure the terminal is at the Idle Prompt
2.
Swipe the credit card, or manually key in the account number and
expiration date.
CREDIT . . . . . . SALE
AMOUNT
0.00
3.
Input the dollar amount of the transaction
without a decimal point and press [ENTER]
Press [ENTER] if the card is present at the
Point of Sale
4.
Card Present?
ENTER=YES, ESC=NO
Or
Press [MENU] if the card is not present.
Note: This prompt is displayed for manually entered
transactions only.
Using the stylus, have the customer sign
on the touch screen display.
5.
Please Sign:
Note: Signature Capture must be enabled. If not
enabled or if the customer does not sign on the
screen, a blank signature line will print on the
receipt.
Continued on next page
User Guide
2
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Credit Cards, Continued
STEP
ACTION
DISPLAY
TEAR SLIP ---->
Press any Key …
6.
The terminal will now contact the host for an
approval and print a receipt.
Press any key for second receipt.
7.
Stop.
Debit Cards
STEP
ACTION
DISPLAY
CREDIT . . . . . . .SALE
ACCOUNT
Æ
1.
2.
Press [ENTER] until the Debit prompt is
displayed.
Swipe the debit card.
(Debit cards cannot be keyed in manually,
they MUST be swiped)
DEBIT . . . . . . .SALE
ACCOUNT
Æ
DEBIT . . . . . . .SALE
AMOUNT
0.00
3.
Input the dollar amount of the transaction
without a decimal point. Press [ENTER].
The terminal will now Prompt you to enter a
Cash Back amount then press [ENTER]
4.
CASH BACK:
0.00
Or
Press [ENTER] to bypass.
Continued on next page
User Guide
3
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Debit Cards, Continued
STEP
ACTION
Input the PIN on the Keypad.
5.
DISPLAY
TOTAL $##.##
Enter your P.I.N.
Note: When using an external PIN pad you will be
prompted on the PIN pad, not on the terminal.
To end hit (ENT)
****
6.
After PIN has been input press [ENTER].
The terminal will now contact the host for
approval and print a receipt.
Press any key for second receipt.
7.
Note: Terminal must be setup when programmed to
print two receipts or Paper Type must be set to
Customized.
8.
Stop.
TEAR SLIP ------>
Press any key . . .
User Guide
4
APPLICATION POS-STD AND POS-PLUS - QSP
EBT Cards
NURIT 8000 SECURE
(Electronic Benefits Transfer)
STEP
1.
ACTION
DISPLAY
From the Idle prompt press [ENTER]
until the display identifies an EBT sale.
EBT . . . . . . . . . SALE
ACCOUNT
Æ
(see right Î)
2.
Swipe the EBT card, or manually enter the account number including the
expiration date, or if required, the ‘GEN’ number.
1. FOOD STAMP
2. CASH BENEFIT
Press [1] for Food stamp
3.
Or
Press [2] for Cash Terminal Benefit
EBT . . . . . . . . . SALE
AMOUNT
0.00
4.
5.
Input the dollar amount of the
transaction without a decimal point then
press [ENTER]
If
Food Stamp
Cash Benefit
Then
Go to step #8.
Proceed to next step.
EBT. . . . . . . . . .SALE
CASH BACK 0.00
6.
The terminal will now Prompt you to
enter a Cash Back amount or press
[ENTER] to bypass.
Continued on next page
User Guide
5
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
(Electronic Benefits Transfer), Continued
STEP
ACTION
If
Food Stamp
Cash Benefit
7.
DISPLAY
Then
Go to step #8.
Proceed to next step.
EBT. . . . . . . . . .SALE
CASH BACK 0.00
8.
The terminal will now Prompt you to enter
a Cash Back amount or press [ENTER]
to bypass.
TOTAL $##.##
Enter your P.I.N.
9.
Input the PIN on the Keypad then press
[ENTER]
Press any key for second receipt.
10.
Note: Terminal must be setup when programmed
to print two receipts or Paper Type must be
set to Customized.
11.
Stop.
TEAR SLIP ------>
Press any key . . .
User Guide
6
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Sale
STEP
ACTION
DISPLAY
CREDIT . . . . .SALE
ACCOUNT
Æ
1.
From the idle prompt press [ENTER]
until the display identifies a check sale.
CHECK . . . . .VERIFY
AMOUNT
0.00
2.
3.
Input the amount to be verified and
Press [ENTER]
Input the 17 digit MICR number from the
check & press [ENTER]
Or
Enter MICR or
Use Check Reader
Place the Check in the Check
Reader/Imager
* Display will vary depending on check hosts
Storing Images,
Please Wait
4.
If a Check Imager was used, the
terminal will display results.
Check Image
Storage Complete
5.
6.
7.
After completion, a successful storage
message will display.
Terminal will print one receipt if paper type is Single/ Double or two receipts
if paper type is Customized.
Stop.
User Guide
7
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Cash Sale
INFORMATION
The Cash EDC mode must be turned on to process cash transactions.
STEP
1.
ACTION
From the Idle prompt press [ENTER] until
the display identifies a Cash Sale.
DISPLAY
CASH . . . . . . . SALE
AMOUNT
0.00
(See right Î)
2.
Input the dollar amount of the sale and press [ENTER]
3.
Terminal will print one receipt if paper type is Single/Double or two receipts if
paper type is Customized.
4.
Stop.
Processing Retail Sale Transactions – With Tip(s)
Turing the Tips function on and off is an option. There may be up to 3 tips/gratuities added per
transaction. You can change the name of the tip for identification/reporting and add a default tip
amount. Use the following step/action table for assistance processing a sale with tip option #1
turned on.
STEP
ACTION
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
1.
Be sure the terminal is at the Idle Prompt
2.
Press [ENTER] until the desired payment method is displayed.
Swipe the credit card, or manually key in the account number and expiration
date.
3.
CREDIT . . . . . . SALE
AMOUNT
0.00
4.
Input the dollar amount of the transaction
without a decimal point. Press [ENTER].
Continued on next page
User Guide
8
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Processing Retail Sale Transactions – With Tip(s), Continued
STEP
ACTION
Input the tip amount and press [ENTER]
DISPLAY
Enter Tip
Amt:
0.00
OR
5.
Press [ENTER] to bypass
Note: Repeat step for Tip #2 and Tip #3
if necessary.
6.
The terminal will now contact the host for approval.
If prompted, have the customer sign
on the touch screen display using the
stylus.
7.
Please Sign:
Note: Signature Capture must be enabled. If not
enabled or if the customer does not sign on
the screen, a blank signature line will print
on the receipt.
TEAR SLIP ------>
Press any key . . .
8.
9.
If requested, press any key to print
second receipt.
Stop.
User Guide
9
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Voids
Void Sale
INFORMATION
A void of a sale can be done if the original sale was Processed in the same batch.
If the original sale was NOT Processed in the same batch a Return must be
processed.
STEP
ACTION
DISPLAY
CREDIT . . VOID/SALE
ACCOUNT
Æ
1.
From the Idle prompt press the [] or []
key until the display identifies a Void/Sale.
(See right Î)
2.
Swipe the credit card or key in the account number and expiration date
manually.
3.
Input the dollar amount to be voided.
4.
Press [ENTER].
Note: Depending upon the host, the terminal might dial out for authorization.
Using the stylus, have the customer sign
on the touch screen display.
5.
Please Sign:
Note: Signature Capture must be enabled. If not
enabled or if the customer does not sign on the
screen, a blank signature line will print on the
receipt.
TEAR SLIP ------>
Press any key . . .
6.
7.
Press any key to print second receipt.
Stop.
User Guide
10
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Void Return
INFORMATION
A Void Refund is done, if the original return is from the same batch. If the refund
is from a different batch, you will not be able to Process a void return.
STEP
ACTION
DISPLAY
CREDIT . . VOID/RTRN
ACCOUNT
Æ
1.
From the Idle prompt press the [] or [] key
until the display identifies a Void/Return.
(See right Î)
2.
Swipe the credit card or key in the account number and expiration date
manually.
3.
Input the amount of the return to be voided.
4.
Press [ENTER].
Note: Depending upon the host, the terminal might dial out for authorization.
Using the stylus, have the customer sign on
the touch screen display.
5.
Please Sign:
Note: Signature Capture must be enabled. If not enabled
or if the customer does not sign on the screen, a
blank signature line will print on the receipt.
TEAR SLIP ------>
Press any key . . .
6.
7.
Press any key to print second receipt.
Stop.
User Guide
11
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Void Forced Sale
INFORMATION
A Void Forced Sale is done, if the original Forced Sale is from the same
batch. If the forced sale is from a different batch, you will not be able to
Process a void forced sale.
STEP
ACTION
DISPLAY
CREDIT . .VOID/FRCD
ACCOUNT
Æ
1.
From the Idle prompt press the [] or []
key until the display identifies a Void/Forced.
(See right Î)
2.
Swipe the credit card or key in the account number and expiration date
manually.
3.
Input the amount of the Forced Sale to be voided.
4.
Press [ENTER].
Note: Depending upon the host, the terminal might dial out for authorization.
Using the stylus, have the customer sign
on the touch screen display.
5.
Please Sign:
Note: Signature Capture must be enabled. If not enabled
or if the customer does not sign on the screen, a
blank signature line will print on the receipt.
TEAR SLIP ------>
Press any key . . .
6.
7.
Press any key to print second receipt.
Stop.
User Guide
12
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Returns
Credit Returns
INFORMATION
A refund to a customer’s credit card account can be done if the original sale is
from a different batch. If the sale and refund are in the same batch process a
Void, otherwise, a refund is done as follows:
STEP
ACTION
DISPLAY
CREDIT . . . . . RETURN
ACCOUNT
Æ
1.
2.
3.
From the Idle prompt press the [] or [] key
until the display identifies a Return.
(See right Î)
Swipe the credit card or key in the account number and expiration date
manually.
Input the amount of the Return.
Note: If the original transaction includes a tip amount then the total amount should be entered
as the return amount.
Press [ENTER].
4.
Note: Depending on the host you may be prompted to
enter the Authorization number from the original
transaction.
Using the stylus, have the customer sign on
the touch screen display.
5.
CREDIT . . . . . RETURN
AMOUNT
Æ
Please Sign:
Note: Signature Capture must be enabled. If not enabled
or if the customer does not sign on the screen, a
blank signature line will print on the receipt.
TEAR SLIP ------>
Press any key . . .
6.
7.
Press any key to print second receipt.
Stop.
User Guide
13
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Debit Return
INFORMATION A return on a debit transaction can only be done using a bank issued debit card.
STEP
ACTION
1.
From the Idle prompt press [ENTER] until DEBIT
is displayed and then use the [] or [] key until
the display identifies a DEBIT RETURN.
(See right Î)
2.
Swipe the debit card
Input the amount of the Return then press
[ENTER]
DISPLAY
CREDIT . . . . . RETURN
ACCOUNT
Æ
DEBIT . . . . . . .RETURN
AMOUNT
Æ
3.
Note: If the original transaction includes a tip amount then
the total amount should be entered as the return
amount.
DEBIT . . . . . . RETURN
25.00
4.
Enter the Authorization number form the original
receipt then press [ENTER].
ENTER AUTH. No:
TOTAL $##.##
Enter your P.I.N.
Input the PIN on the Keypad.
5.
To end hit (ENT)
****
6.
After PIN has been input press [ENTER]
7.
If prompted, press any key to print second receipt.
8.
Stop.
User Guide
14
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Verify
INFORMATION
This function is used to ensure that a customer has adequate funds on their credit
card by obtaining an authorization (THIS DOES NOT CHARGE THE
CUSTOMER’S ACCOUNT).
STEP
ACTION
DISPLAY
CREDIT . . . . .VERIFY
ACCOUNT
Æ
1.
From the Idle prompt press the [] or []
key until the display identifies a Verify.
(See right Î)
2.
Swipe the credit card or key in the account number and expiration date
manually.
CREDIT . . . . .VERIFY
AMOUNT
0.00
3.
Input the amount to be verified.
4.
Press [ENTER]. The terminal will process the transaction.
5.
Upon approval, one receipt without a signature line will be printed.
6.
Stop.
User Guide
15
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Forced Transaction
INFORMATION
When authorization has previously been obtained, a Forced Sale should be done to
process the transaction.
STEP
1.
ACTION
From the Idle prompt press the [] or
[] key until the display identifies a
Forced Sale.
DISPLAY
CREDIT . . . . .FORCED
ACCOUNT
Æ
(See right Î)
2.
Swipe the credit card or key in the account number and expiration date
manually.
3.
Input the amount of the transaction. This amount should be equal to or less
than the amount that was verified.
CREDIT . . . . .FORCED
21.00
4.
Input the authorization number previously
obtained.
Using the stylus, have the customer
sign on the touch screen display.
5.
ENTER AUTH. NO:
Please Sign:
Note: Signature Capture must be enabled. If not
enabled or if the customer does not sign on
the screen, a blank signature line will print
on the receipt.
TEAR SLIP - - - ->
Press Any Key
6.
7.
Press any key for the second receipt to
print.
Stop.
User Guide
16
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Batching
INFORMATION
To Process a manual batch release, or settlement of transactions stored in the
NURIT 8000 SECURE memory, use the following step/action table for assistance
STEP
ACTION
From the Idle prompt press [F]
1.
(See right Î)
DISPLAY
FUNCTION MENU
1.REPORT
2.BATCH
3.REVIEW
4.FIND
Note: Prompts will vary by host.
2.
Press [2] to start batch process.
CHOOSE HOST:
3.
Select the number that corresponds with
the host you are batching or press [1] for
ALL.
1.ALL
2.CREDIT HOST
3.DEBIT HOST
Note: Prompt will vary with terminal setup.
CHOOSE FUNCTION
Press [1] to close the batch.
1.Close Batch
2.Host Totals
3.Summary Report
4.
Note: Prompts will vary by host.
5.
The terminal will contact the host processor, close the batch and print a batch
report.
6.
Stop.
Note:
If a terminal is programmed for auto batch, the host will close the batch
automatically each night at a specific time and the terminal will print a batch
report. However, the transactions will only clear at the time of the first sale
of the new batch. Although your terminal will be programmed for auto batch,
you still have the option to batch manually. Images are uploaded at the start
of the batch process.
User Guide
17
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Accessing Hot Keys
FUNCTION
DESCRIPTION
Hot Keys are short cuts to reports and functions. Hot Keys must be
programmed when the terminal file is built and downloaded into the terminal
with the application and parameters. A Hot Key List is printed at the end of
the Print Setup Report.
Example of
Print Setup
Report:
STEP
HotKey List:
F1:
F2:
F3:
Driver License
Open a Tab
Close a Tab
ACTION
DISPLAY
CREDIT . . . . .SALE
ACCOUNT
Æ
1.
If necessary, press [MENU/ESC] to
return the terminal to the idle prompt.
2.
Press the [F] key at the same time as pressing the number key on the
list. I.E., press [F] and [2] to Open a Tab.
3.
Stop.
User Guide
18
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Driver License Verification *
INFORMATION
This feature is programmable at the Nurit Control Center level using one of
the terminal’s eight hot keys. The Programmed Hot Keys are listed at the
bottom of the Setup Report.
*NOTE: All Driver License Verification functions are available with
POS7PLUS application only.
STEP
ACTION
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
1.
From the idle prompt, press the [F] key at
the same time as pressing the number
key for Driver License Verification.
Swipe the customer’s Driver License with the
Magnetic strip facing down and to the right.
Swipe DL Card ->
2.
Note: For a successful swipe the customer’s DL must
have a magnetic strip.
ENTER SERVER ID
0
3.
Enter the Server ID then press [ENTER].
Select the purchase type for the Age
Verification.
4.
SELECT
2: LIQ
1: TOB
3: SCAN
1. Tobacco
2. Liquor
3. Scan (Displays age and issuing state)
Continued on next page.
User Guide
19
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Driver License Verification, Continued
STEP
ACTION
5.
The terminal will read the magnetic strip and
determine if the customer’s age is
appropriate for the type of purchase.
DISPLAY
LIQUOR APPROVED
Note: Prompts will vary depending on the selection.
Age is: 30
PA
The display will show the customer’s age
and resident state.
6.
Note: Prompts will vary by customer.
7.
Stop.
User Guide
20
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
DL Verification General Report *
STEP
ACTION
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
1.
From the idle prompt, press the [F] key at
the same time as pressing the number
key for Driver License Verification.
Swipe DL Card ->
2.
Press the [BS] key to list the available
functions.
DRIVER LICENSE
3.
Press [ENTER] to print the report.
4.
Stop.
1.General Report
2.Clerk Report
3.Supported States
4.Clear DL Data
User Guide
21
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
DL Verification Clerk Report *
STEP
1.
ACTION
From the idle prompt, press the [F] key at
the same time as pressing the number
key for Driver License Verification.
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
Swipe DL Card ->
2.
Press the [BS] key to list the available
functions.
DRIVER LICENSE
3.
Press [2] to print the Clerk Report.
1.General Report
2.Clerk Report
3.Supported States
4.Clear DL Data
ENTER SERVER ID:
4.
Enter the Server ID then press [ENTER].
5.
Stop.
User Guide
22
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
DL Verification Supported States *
STEP
ACTION
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
1.
From the idle prompt, press the [F] key at
the same time as pressing the number
key for Driver License Verification.
Swipe DL Card ->
2.
Press the [BS] key to list the available
functions.
DRIVER LICENSE
3.
Press [3] for Supported States. A list of the
states currently supported will be printed.
4.
Stop.
1.General Report
2.Clerk Report
3.Supported States
4.Clear DL Data
The list of supported states is updated periodically as states change the type of license
issued. The following is a list of the supported states when this document was written and
might not be current. Print a list from your terminal for the latest information.
AR – Arkansas
AZ – Arizona
CA – California
CO – Colorado
DC – District of Columbia
FL – Florida
IA – Iowa
KS – Kansas
LA – Louisiana
MA – Massachusetts
MD – Maryland
MI – Michigan
MN – Minnesota
MT – Montana
NM – New Mexico
OH – Ohio
PA – Pennsylvania
TX – Texas
VA – Virginia
VT – Vermont
WI – Wisconsin
ON – Ontario, Canada
User Guide
23
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Clear Driver License Data *
STEP
ACTION
DISPLAY
CREDIT . . . . . . SALE
ACCOUNT
Æ
1.
From the idle prompt, press the [F] key at
the same time as pressing the number
key for Driver License Verification.
Swipe DL Card ->
2.
Press the [BS] key to list the available
functions.
DRIVER LICENSE
3.
Press [4] to clear the Driver License Data.
1.General Report
2.Clerk Report
3.Supported States
4.Clear DL Data
DATA CLEARED
4.
The data will be cleared.
5.
Stop.
User Guide
24
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Quick Service Payment
INFORMATION
QSP is used in Fast Food Restaurants, Parking Garages and Motion Picture Theaters
(Cinemas). This allows the acceptance of credit cards as the payment method without
requiring authorization, receipts or signatures. QSP supports swiped transactions only;
manual entry transactions are processed in the normal manner. This means that manual
entry transactions will contact the host for authorization and will print a receipt with a
signature line. Credit Card sales and voids are the only transaction types supported by
QSP. The Credit EDC capture type must be Terminal Based for QSP.
A Floor Limit can be specified for each function (authorization, receipt and signature) for
each card type to be processed. This must be specified in the file built for the specific
terminal and downloaded into the terminal. QSP Mode information is printed on the Print
Setup Report.
This function is available only when supported and requested by the Host
Processor. The capture type must be terminal based.
Please review the following chart of default Floor Limits:
CARD TYPE
MERCHANT CATEGORY
DEFAULT FLOOR LIMIT
MASTER CARD
Fast Food Restaurant
$25.00
MASTER CARD
Parking Garage
$50.00
MASTER CARD
Cinema
$35.00
VISA
Restaurant (all types)
$25.00
VISA
Cinema
$25.00
VISA
Parking Garage/Lot
$75.00 for Authorization $150.00
for Signature and $25.00 for
Receipt
User Guide
25
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Processing a QSP Sale
STEP
ACTION
DISPLAY
CREDIT …… SALE
ACCOUNT
Æ
1.
Be sure the terminal is at the Idle Prompt
2.
Swipe the credit card.
CREDIT …… SALE
AMOUNT
0.00
3.
4.
5.
Input the dollar amount of the transaction without
a decimal point and press [ENTER]
If
Then
The transaction amount is less than the
authorization floor limit:
The Host Processor will not be
contacted for authorization.
The transaction amount is greater than
the auth. floor limit:
The terminal will contact the Host for
authorization.
If
Then
The transaction amount is less than the
receipt floor limit:
The terminal will display a “Print
Receipt?” prompt (see step #6).
The transaction amount is greater than
the floor limit:
A receipt will be printed.
Print Receipt?
ENTR=YES, MENU=NO
6.
Press [ENTER] to print a receipt or [MENU/ESC]
for no receipt.
User Guide
26
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Processing a QSP Sale, Continued
STEP
ACTION
7.
DISPLAY
If
Then
The transaction amount is less than the
signature floor limit:
The receipt will not have a signature
line.
The transaction amount is greater than
the signature floor limit:
The receipt will have a signature line.
TEAR SLIP - - - ->
Press Any Key
8.
9.
Press any key for second receipt to print.
Stop.
User Guide
27
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Voiding a QSP Sale
STEP
ACTION
DISPLAY
CREDIT . . . VOID/SALE
ACCOUNT
Æ
1.
From the Idle prompt press [VOID] until the display
identifies a Void/Sale.
(See right Î)
2.
Swipe the credit card or key in the account number and expiration date manually.
3.
Input the dollar amount to be voided then press [ENTER].
4.
If
Then
The transaction amount is less than the
receipt floor limit:
The terminal will display a “Print
Receipt?” prompt (see step #5).
The transaction amount is greater than
the floor limit:
A receipt will be printed.
Print Receipt?
ENTR=YES,MENU=NO
5.
Press [ENTER] to print a receipt or [MENU/ESC]
for no receipt.
6.
If
Then
The transaction amount is less than the
signature floor limit:
The receipt will not have a signature
line.
The transaction amount is greater than
the signature floor limit:
The receipt will have a signature line.
TEAR SLIP - - - ->
Press Any Key
7.
8.
Press any key for second receipt to print.
Stop.
User Guide
28
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Menu Options
INFORMATION
The NURIT 8000 SECURE has a menu with several options that control many of
the terminal’s basic operational functions. The menu is divided into main menus
and sub-menus that can be accessed by pressing the [MENU/CANCEL] key.
Accessing the Main Menu
STEP
ACTION
DISPLAY
CREDIT …… SALE
ACCOUNT
Æ
1.
From the Idle Prompt
[MENU/CANCEL] key.
press
the
Use the [] and [] keys to scroll
through the options then press [ENTER]
to select.
2.
OR
Press the number on the keypad that
corresponds with your selection.
MENU SCREEN:
1.Reports
2.Merch. Params
3.Merch. Option
4.Host Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
3.
Press [MENU/CANCEL] to return to the idle CREDIT . . . . . . SALE prompt.
4.
Stop.
User Guide
29
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
1. Reports
The first menu is the Report Menu, which generates ten different types of reports:
MENU
DESCRIPTION
‰ Default Report ‰ Current Report ‰ History Report ‰ Display Transactions
‰ Receipt Copy ‰ Performance
‰ Tip Report
‰ Report Setup
‰ RAM DISK Report *
‰ Communication Log Report *
*NOTE: These features are available with the POS_PLUS application only.
REPORT
TYPES
You will be prompted in some Report sub-menus to choose a report type. Below
is a list of report types and their definitions.
REPORT
DEFINITION
CONDENSED
REPORT
This type of report will print the transaction number, card type,
transaction type, last four digits of the account number, and the
amount of the sale.
SHORT REPORT
This type of report will print the transaction type and the
amount of the sale.
JOURNAL REPORT
This type of report will print a full receipt style copy of each
transaction.
TOTALS ONLY
This type of report will print daily totals only.
User Guide
30
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print the Default Report
FUNCTION
DESCRIPTION
This is a report of the terminal's daily transactions, which has been customized, or
has set defaults from the Current Report (see Current Report on the following
page).
STEP
ACTION
From the main MENU SCREEN press
[ENTER/CANCEL]
1.
OR
Press [1] to access the Reports Menu
DISPLAY
REPORTS:
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and press [ENTER].
3.
From the Reports Menu Press [ENTER] OR Press [1] to select Default Report
4.
Stop.
User Guide
31
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print the Current Report
FUNCTION
DESCRIPTION
STEP
Current report will print the terminal's daily transactions, and can be customized
with specific options. This is where the Default Report is set.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [2] to select Current Report
Use the [] and [] keys to scroll
through the Report Type options then
press [ENTER] to select.
3.
OR
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
CUR. REPORT TYPE
1.Condensed Rprt
2.Short Report
3.Journal Report
4. TOTALS ONLY
Press the number corresponding with
your selection.
Use the [] and [] keys to scroll
through the EDC Type options then press
[ENTER] to select.
4.
CHOOSE EDC TYPE
1.ALL
2.CREDIT
3.DEBIT
OR
Press the number corresponding with
your selection
Use the [] and [] keys to scroll
through the Card Type options then press
[ENTER] to select.
5.
OR
Press the number corresponding with
your selection
ENTER CARD TYPE
1.ALL
2.VISA
3.MasterCard
4.AMEX
5.Diners
6.CarteBlanch
7.Disc/NOVUS
8.enRoute
9.JCB
Continued on next page
User Guide
32
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print the Current Report, Continued
STEP
ACTION
DISPLAY
Use the [] and [] keys to scroll through
Sorting Options then press [ENTER] to
select.
6.
SORT METHOD:
1.By Trans #
2.By Card Type
3.By Server ID
OR
Press the number corresponding with your
selection
Use the [] and [] keys to scroll through
the Transaction Type options then press
[ENTER] to select.
7.
OR
Press the number corresponding with your
selection
To
8.
9.
CHOOSE TRAN. TYPE
1.ALL
2.SALE
3.FORCED
4.VERIFY
5.RETURN
6.VOID/SALE
7.VOID/RTRN
8.VOID/FRCD
Then
Save this
as your
default
report
Press
[ENTER]
Keep your
current
default
setting
Press [MENU]
Set Cur. Defaults?
ENTR=YES,MENU=NO
Stop.
User Guide
33
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print History Reports
FUNCTION
DESCRIPTION
STEP
This report will allow you to print previous batch totals for the last 300 batches.
You can print a total report of several batches, or you can print a report showing
totals per batch.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [3] to select History Report.
Using the numeric keypad input the batch
date you would like the report to begin
with.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
From Batch Date:
10/01/02
Then press [ENTER]
3.
Using the numeric keypad input the batch
date you would like the report to end with.
To Batch Date:
10/15/02
Then press [ENTER]
Use the [] and [] keys to select if you
would like the report by Total or Per Batch
then press [ENTER]
4.
HISTORY REPORTS
1.Total
2.Per Batch
OR
Press the number corresponding with
your selection
Continued on next page
User Guide
34
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print History Reports, Continued
STEP
ACTION
Use the [] and [] keys to scroll
through the EDC Type options then press
[ENTER] to select.
5.
DISPLAY
CHOOSE EDC TYPE
1.ALL
2.CREDIT
3.DEBIT
OR
Press the number corresponding with
your selection
Use the [] and [] keys to scroll
through the Card Type options then press
[ENTER] to select.
6.
OR
Press the number corresponding with
your selection
Use the [] and [] keys to scroll
through the Transaction Type options
then press [ENTER] to select.
7.
OR
Press the number corresponding with
your selection
8.
ENTER CARD TYPE
1.ALL
2.VISA
3.MasterCard
4.AMEX
5.Diners
6.CarteBlanch
7.Disc/NOVUS
8.enRoute
9.JCB
CHOOSE TRAN. TYPE
1.ALL
2.TOTALS ONLY
3.SALE
4.FORCED
5.VERIFY
6.RETURN
7.VOID/SALE
8.VOID/RTRN
Stop.
User Guide
35
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Display Transactions
FUNCTION
DESCRIPTION
STEP
This option will allow you to view daily transactions on the terminal
display. You can also print another receipt copy of the displayed
transaction or void that transaction.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [4] to select Display Trans.
Use the [] and [] keys to select the
method you would like to view the
transaction then press [ENTER].
3.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
Display Trans.
1.Scroll All
5.By Trans. #
6.By Card Type
7.By Card Num.
OR
Press the number corresponding with
your selection
Note: Subsequent prompts will vary with
this menu choice.
Use the [] and [] keys to scroll
through the EDC Type options then press
[ENTER] to select.
4.
CHOOSE EDC TYPE
2.CREDIT
3.DEBIT
4.EBT
5.Cash
OR
Press the number corresponding with
your selection
Continued on next page
User Guide
36
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Display Transactions, Continued
STEP
ACTION
DISPLAY
If
5.
Then
You selected to
scroll through all
transaction
The first transaction will show on the display.
FORCED will allow you to scroll through the
transactions.
You selected to
view by
Transaction #
You will be prompted to input the Transaction #
You selected to
view by Card Type
You will be prompted to select a card type
If you selected to
view by Card
Number
You will be prompted to enter the last four
digits of the card number.
#0001 SL 12.00
6.
To print another copy of the receipt for
this transaction press [ALPHA].
Note: Display will reflect your transaction.
MasterCard
123456
0805
5454123456789876
#0001 SL 12.00
To Void this transaction press [CLEAR].
7.
MasterCard
123456
0805
Note: Display will reflect your transaction.
5454123456789876
Void Trans #1?
ENTR=YES,MENU=NO
Press [ENTER].
8.
9.
Stop.
User Guide
37
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Receipt Copy
FUNCTION
DESCRIPTION
This option will print a Merchant’s copy (full account number and signature line) of
the last transaction, a Customer copy (truncated account number) of the last
transaction or a copy (Customer) of any receipt. If any function was executed
after the transaction, the last receipt function cannot be accessed; the any receipt
function must be used.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [5] to select Receipt Copy.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
RECEIPT COPY:
3.
Press the number that corresponds to the
type of receipt required.
1.Last Cust. Rcpt
2.Any Receipt
3.Last Mrch. Rcpt
CHOOSE EDC TYPE
4.
If Any Receipt was selected, choose the
EDC type by pressing the corresponding
number.
2.CREDIT
3.DEBIT
4.CASH
Note: Display will reflect terminal setup.
CHOOSE EDC TYPE
5.
Enter the number of the transaction
requiring the receipt then press [ENTER].
6.
Stop.
2.CREDIT
3.DEBIT
4.CASH
Transaction # ?
User Guide
38
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print the Performance Report
FUNCTION
DESCRIPTION
This option will print a report listing the percentages of denials, approvals, swipes,
manual entries, etc.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [6] to select Performance.
Use the [] and [] keys to scroll
through the EDC Type options then press
[ENTER] to select.
3.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
CHOOSE EDC TYPE
2.CREDIT
3.DEBIT
4.EBT
OR
Press the number corresponding with
your selection.
The Performance Report will print.
To
Then
Press
[ENTER]
4.
Reset the
Performance
Report
Keep the
Default
Report data
5.
Reset perf rprt?
ENTR=YES, MENU=NO
*You will be
prompted to
input the
password
Press
[MENU]
Stop.
User Guide
39
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Tip Report
FUNCTION
DESCRIPTION
STEP
This option will print a report that provides tip detail by server number.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [7] to select Tip Report.
Press [1] to view report for ALL servers
3.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
CHOOSE SERVER
1. ALL
2.Specific Servr
OR
Press [2] to view report for a specific
server.
Use the [] and [] keys to scroll
through the EDC Type options then press
[ENTER] to select.
4.
OR
CHOOSE EDC TYPE
1.ALL
2.CREDIT
3.DEBIT
4.EBT
5.CASH
Press the number corresponding with
your selection
Use the [] and [] keys to scroll
through the Card Type options then press
[ENTER] to select.
5.
OR
Press the number corresponding with
your selection
ENTER CARD TYPE
1.ALL
2.VISA
3.MasterCard
4.AMEX
5.Diners
6.CarteBlanch
7.Disc/NOVUS
8.enRoute
9.JCB
Continued on next page.
User Guide
40
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Tip Report, Continued
STEP
6.
7.
ACTION
DISPLAY
To
Then
Save this as
your default
report
Press
[ENTER]
Keep your
current
default
setting
Press
[MENU]
Set Cur. Defaults?
ENTR=YES, MENU=NO
Stop. The report will begin printing.
User Guide
41
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Report Set up – Printing Visa/MC Options
FUNCTION
DESCRIPTION
This function allows the option of having Visa and MasterCard print together
(default) or separately. The report must be sorted by card type for the Visa and
MasterCard transactions to be separate.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [8] to select Report Setup.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
Report Setup
1.Vis/Mastr Setp
2.Tip Discount
3.
Press [ENTER] to select
1. Visa/MasterCard Setup
4.
Use the [] and [] keys to select if you
would like Visa and MasterCard printing
together or separately then press
[ENTER].
OR
Press the number corresponding with
your selection
5.
Stop.
Vis/Mastr Setup
1.Separately
2.Together
User Guide
42
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Report Setup – Tip Discount
FUNCTION
DESCRIPTION
This menu options allows the tip discount percentage to be set. This function
applies to restaurant mode only. Tip Discount must be enabled in the individual
tip areas to take affect.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [8] to select Report Setup.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
Report Setup
1.Vis/Mastr Set
2.Tip Discount
Press [ENTER] to select
2. Tip Discount
3.
Use the [] and [] keys to scroll
through the Card Type options then press
[ENTER] to select.
4.
OR
Press the number corresponding with
your selection.
SELECT CARD TYPE
1.ALL
2.VISA
3.MasterCard
4.AMEX
5.Diners
6.CarteBlanch
7.Disc/NOVUS
8.enRoute
9.JCB
Tips % Discount
5.
Input the percent (%) amount then press
[ENTER]
0.00
Note: Be sure whole percents are to the left of
the decimal point.
6.
Stop.
User Guide
43
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
RAM Disk Report
FUNCTION
DESCRIPTION
A report listing the record size and maximum number of transactions for each EDC
type is printed via this function.
NOTE: This feature is available with POS_PLUS application only.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Press [9] to select RAMDISK Report.
3.
The RAMDISK Report will print.
4.
Stop.
1.Default Report
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
User Guide
44
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Communication Log Report
FUNCTION
DESCRIPTION
Use this function to print a communication log of the last transaction or batch
processed or to clear the log.
NOTE: This feature is available with POS_PLUS application only.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu, press [1] to access
the Reports Menu.
Input the Password and press [ENTER].
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
REPORTS:
2.
Use the [] key to scroll to menu option
10. ComLog Rprt and then press
[ENTER].
2.Current Report
3.History Report
4.Display Trans.
5.Last Receipt
6.Performance
7.Tip Report
8.Report Setup
9.RAMDISK Report
10.ComLog Rprt
ComLog Report
3.
4.
Press [1] to print the current
communication log or press [2] to clear
the communication log information.
1.ComLog Print
2.ComLog Clear
Stop.
User Guide
45
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
2. Merchant Parameters
MENU
DESCRIPTION
This menu contains nine different functions that can be changed manually.
They are:
‰ Authorizations
‰ Edit Trailer
‰ Set Batch Time
‰ Security Level
‰ Set Cash EDC
‰ Server/Invoice
‰ Edit Header
‰ Merchant Fee
‰ Site ID
Authorizations – TRANSACTION TYPE
FUNCTION
DESCRIPTION
STEP
This function allows specific transaction types to be enabled and disabled. For
example, Voids, Returns, Forced Sales, etc. can be turned off or on.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [1] to access Authorizations
1.Authorizations
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8.Srvr/Clrk/Invoice
9. Site ID
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
AUTHORIZATION
4.
Press [1] to edit authorization for
Transaction Types.
1.Trans. Types
2.Card Types
3.Debit Prompt
Continued on next page
User Guide
46
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Authorizations – Transaction Type, Continued
STEP
ACTION
5.
Use the [] and [] keys to scroll
through the EDC Type options then press
[ENTER] to select.
OR
Press the number corresponding with
your selection.
Use the [] and [] keys to select the
Transaction Type then press [ENTER].
6.
OR
Press the number corresponding with
your selection.
Use the [] and [] keys to select
Enable, Disable or Manager Only for the
Transaction Type then press [ENTER].
7.
DISPLAY
CHOOSE EDC TYPE
2.CREDIT
3.DEBIT
4.EBT
CREDIT
1. FORCED (EN)
2. VERIFY (EN)
3. RETURN (EN)
4. VOID/SALE (EN)
5. VOID/RTRN (EN)
6. VOID/FRCD (EN)
CREDIT FORCED
1.Disabled
2.Always Enable
3.Manager Only
Or
Press the number corresponding with
your selection
8.
Stop.
User Guide
47
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Authorizations – Card Type
FUNCTION
DESCRIPTION
STEP
This function allows specific card types to be enabled and disabled. For example,
Visa, MasterCard, Discover, Amex, etc. can be turned off or on.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [1] to access Authorizations.
1.Authorizations
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8. Srvr/Clrk/Invoice
9. Site ID
ENTER PASSWORD:
3.
Input the Password and press [ENTER].
AUTHORIZATION
4.
Press [2] to edit authorization for Card
Types.
5.
Use the [] and [] keys to scroll
through the Card Type options then
press [ENTER] to select.
Or
Press the number corresponding with
your selection
1.Trans. Types
2.Card Types
3.Debit Prompt
Choose Card Typ
1.VISA +
2.MasterCard +
3.AMEX +
4.Diners +
5.CarteBlanch +
6.Disc/NOVUS +
7.enRoute +
8.JCB +
Continued on next page
User Guide
48
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Authorizations – Card Type, Continued
STEP
ACTION
DISPLAY
VISA +
Use the [] and [] keys to select
Enable or Disable for the Card Type then
press [ENTER].
6.
1.Disabled
2.Always Enable
Or
Press the number corresponding with
your selection
‘+’ indicates enabled and
‘-‘ indicates disabled.
7.
Stop.
Authorizations – Debit Prompt
FUNCTION
DESCRIPTION
STEP
This function prompts the user the choose CREDIT or DEBIT when a credit card
is swiped and the payment type is CREDIT.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [1] to access Authorizations
1.Authorizations
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8 Srvr/Clrk/Invoice
9. Site ID
Continued on next page
User Guide
49
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Authorizations – Debit Prompt, Continued
STEP
ACTION
DISPLAY
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
AUTHORIZATION
1.Trans. Types
2.Card Types
3.Debit Prompt
4.
Press [3] to select 3. Debit Prompt
DEBIT PROMPT
1.OFF
2.ON
5.
6.
Press [1] to turn Debit Prompt OFF or
press [2] to turn Debit Prompt ON.
Stop.
User Guide
50
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Security Levels
FUNCTION
DESCRIPTION
This option allows merchants to set security levels for the Main Menu, Batching,
Card Security, Manual Entry of a credit card, and printing format of a credit card
number.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
3.
Press [2] to access Security Level
Use the [] and [] keys to select the
option you are editing security for and
then press [ENTER].
Or
1.Authorization
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8. Srvr/Clrk/Invoice
9. Site ID
SECURITY SWITCH
1.Menu
2.Batch
3.Print Account
4.Secure Card
5.Crd Man. Entry
Press the number corresponding with
your selection
4.
5.
Use the [] and [] keys to Enable the
function or set security to Manager Only
then press [ENTER].
Or
Press the number corresponding with
your selection
Batch:
1.Always Enable
2.Manager Only
Stop.
FUNCTION
OPTIONS
Menu
Always Enabled and Manager Only
Batch
Always Enabled and Manager Only
Print Account
Always Full, Full on Report and Always Short
Secure Card
No Security, Last 4 Digits and All Digits
Card Manual Entry
(Password Protected)
Disabled and Always Enabled
User Guide
51
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Header/Trailer
FUNCTION
DESCRIPTION
The receipt header and trailer can be changed manually through the terminal. A
specific line, character, or entire header/trailer can be changed, if needed.
Both Header and Trailer are composed of five lines, 24 characters per line.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
Press [3] to Edit the Receipt Header
2.
Or
Press [4] to Edit the Receipt Trailer
1.Authorization
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8. Srvr/Clrk/Invoice
9. Site ID
Header Text 1 N
3.
Input in the text that you want printed out
on the receipt. (See instructions below)
To change the letters, first press the number key that corresponds with
the desired letter then press the [ALPHA] key and the [F] key
simultaneously to cycle through the other characters also on that key
For example:
4.
5.
The #2 key on the keypad also has the letters A, B and C printed on it.
When you first press this key, the display will show the number 2, by
pressing the [ALPHA] key and the [F] key simultaneously it will
cause the display to change from 2 to the letter A, press [ALPHA] and
[2] again and then it becomes a B and finally C before starting all over
again back to the number 2.
Press and hold the [F] key then tap the [9] to move the cursor to the right.
Press and hold the [F] key then tap the [8] to move the cursor to the left.
Press [] to scroll to the next line.
Continued on next page.
User Guide
52
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Header/Trailer, Continued
STEP
ACTION
6.
When
all
information
has
been
entered/edited
press
[MENU]
to
complete process.
DISPLAY
SAVE CHANGES?
ENTR=YES, MENU=NO
If prompted, press [ENTER] to save your
changes.
7.
Stop.
User Guide
53
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Cash EDC
FUNCTION
DESCRIPTION
Cash will be an addition to your Payment Modes, and will record cash
transactions when this option is enabled. No batching or transfer of money is
part of this process. Cash EDC is used only to track cash transactions.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [5] to Set Cash EDC
1.Authorization
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8. Srvr/Clrk/Invoice
9. Site ID
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
CASH EDC SET:
Press [1] to Set EDC With Cash
4.
1.WITH CASH
2.WITHOUT CASH
Or
Press [2] to Set EDC Without Cash
5.
Stop.
User Guide
54
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Setting the Merchant Fee
FUNCTION
DESCRIPTION
STEP
Use this function to add a Merchant Fee to a debit transaction.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [6] for Merchant Fee.
1.Authorization
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8. Srvr/Clrk/Invoice
9. Site ID
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
Merch Fee: $0.00
New Rate: 0.00
4.
Input the Merchant Fee then press
[ENTER]
ARE YOU SURE
ENTR=YES, MENU=NO
5.
Press [ENTER]
Continued on next page
User Guide
55
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Setting the Merchant Fee, Continued
STEP
ACTION
DISPLAY
On CashBack Only
ENTR=YES, MENU=NO
6.
7.
Press [ENTER] to add fee to CashBack
transactions only or [MENU] to add fee to
all debit transactions.
Stop.
Set Batch Time
FUNCTION
DESCRIPTION
STEP
This option will allow the batch time in the terminal to be set for a specific time.
This is used on AUTOBATCH terminals only. Set Batch Time will print a batch
report and will not actually dial to batch.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [7] to set the Autobatch Batch
Time
1.Authorizations
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8 Srvr/Clrk/Invoice
9. Site ID
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
Continued on next page
User Guide
56
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Batch Time, Continued
STEP
ACTION
DISPLAY
SET BATCH TIME:
05:30
4.
Input the desired time in military time
(24 hour) and press [ENTER]
5.
If the terminal was programmed with more than one Autobatch EDC, you will
be prompted to choose host before setting the batch time.
6.
Stop.
User Guide
57
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Server ID/Clerk ID/Invoice Mode
FUNCTION
DESCRIPTION
STEP
This will allow the terminal to prompt for a server/clerk ID, invoice
number, or both. For Retail terminals with no Tip active, the function is
Clerk ID. For a Retail terminal with at least one Tip active or a
Restaurant terminal, the function is Server ID.
If Server/Clerk ID Mode is activated, up to 100 ID/name designations
can be entered and stored in the terminal. When storing the
number/name designations, the server numbers are restricted to from
1 to 100.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
2.
Press [8] for Server/Invoice Mode.
1.Authorization
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8. Srvr/Clrk/Invoice
9. Site ID
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
SERVER ID MODE:
Use the [] and [] keys to select OFF
or ON and then press [ENTER].
4.
1.OFF
2.ON
Or
Press the number corresponding with
your selection.
NOTE: Display will change to reflect
Retail or Restaurant configuration.
Continued on next page.
User Guide
58
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Server ID/Clerk ID/Invoice Mode, Continued
STEP
ACTION
DISPLAY
SERVER ID MODE:
Enter the Server ID number a name is to
be assigned to then press [ENTER].
5.
Or
1.OFF
2.ON
ENTER SERVER ID
1
Press [MENU] to bypass.
Srv #1 Name: 1 N
6.
7.
Using the method described in Editing
Header, enter the 19-character name.
Press [ENTER] when the name has been
entered.
Continue in this manner until all server
names have been entered. Press
[MENU] to accept the entered names and
continue to Invoice Mode.
Use the [] and [] keys to select OFF
or ON then press [ENTER].
8.
Srv #14 Name: 1 N
ALICE
ENTER SERVER ID
15
INVOICE MODE:
1.OFF
2.ON
Or
Press the number corresponding with
your selection.
9.
Note: In the Restaurant application, there are two more options after Invoice;
Table #’s and Guest #’s.
10.
Stop.
User Guide
59
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Site ID
FUNCTION
DESCRIPTION
This option is used mainly for programming purposes, it allows customer
service to view, or change the terminal number.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [2]
to access Merchant Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCHANT PARAMS
Press [9] to access Site ID
2.
3.
The UNIQUE and current Site ID used to
program the terminal will display.
Press [ENTER] to change the ID.
1.Authorization
2.Security Level
3.Edit Header
4.Edit Trailer
5.Set Cash EDC
6.Merchant Fee
7.Set Batch Time
8.Server ID/Invoice
9. Site ID
CHANGE SITE ID?
0000100
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Enter Site ID
5.
6.
Enter the new Site ID then press
[ENTER].
Stop.
User Guide
60
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
3. Merchant Options
This Main Menu has fifteen options that can be enabled or disabled manually
through the terminal.
MENU
DESCRIPTION
‰ Paper Type
‰ No-Paper Mode
‰ Battery Saver ‰ Print Disclaimer
‰ Print Setup
‰ Store & Forward
‰ Bridge Comm *
‰ Buzzer Set
‰ Set Menu Type
‰ Check Reader
‰ Language Setup
‰ Operation Mode
‰ Set Halo
‰ Sign Option *
*
*NOTE: These features are available with the POS_PLUS application only.
Paper Type
FUNCTION
DESCRIPTION
This option sets the paper type to single ply, double ply, or customized.
Single ply prints two receipts (for credit by default, also for debit and EBT if
specified in the terminal file), double ply prints one receipt (with account
truncation) and customized prints two receipts for all payment modes.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [ENTER] for Paper Type
Use the [] and [] keys to highlight
your selection and then press [ENTER].
3.
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
PAPER TYPE
1.Single Ply
2.Double Ply
3.Customized
Or
Press the number corresponding with
your selection.
4.
Stop.
User Guide
61
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Buzzer Set
FUNCTION
DESCRIPTION
Enables or disables tone when performing certain terminal functions.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [3] for Buzzer Set
Use the [] and [] keys to your
selection and then press [ENTER].
3.
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
BUZZER SET:
1.OFF
2.ON
Or
Press the number corresponding with
your selection.
4.
Stop.
User Guide
62
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Operation Mode
FUNCTION
DESCRIPTION
This option allows the terminal to be set at two different modes, Normal or Demo
(Demo mode for training; Normal mode for live transactions). If the terminal is set in
Demo mode for training purposes, you must revert back to Normal mode for live
transactions.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [4] for Operation Mode
Use the [] and [] keys to your
selection and then press [ENTER].
3.
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
OPERATION MODE:
1.Demo Mode
2.Normal Mode
Or
Press the number corresponding with
your selection.
ARE YOU SURE?
ENTR=YES, MENU=NO
4.
5.
Press [ENTER] to execute change.
Stop.
User Guide
63
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Battery Saver
FUNCTION
DESCRIPTION
This option puts terminal in a standby mode. It can be enabled or disabled.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [5] for Battery Saver
Use the [] and [] keys to your
selection and then press [ENTER].
3.
Or
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
BATT SAVER ~ ON
1. OFF
2. Auto Off Only
3. Radio Only
4. Radio+Auto Off
Press the number corresponding with
your selection.
ARE YOU SURE?
ENTR=YES, MENU=NO
4.
5.
Press [ENTER] to execute change.
Input the seconds that should elapse
prior to the battery saver being initiated.
IDLE TIME: [sec]
60
Then press [ENTER]
6.
Stop.
Continued on next page.
User Guide
64
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Battery Saver, Continued
OPTION
Off
DEFINITION
This option turns the battery saver off.
Radio Only
This option will shut off only the radio after a specific amount
of time is set in terminal.
Radio + Auto Off
This shuts the radio and terminal off after a specific amount of
time set in terminal.
Auto Off Only
With this option only the terminal will shut off after a specific
amount of time set in the terminal. The Radio will stay on.
User Guide
65
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Prints Disclaimer
FUNCTION
DESCRIPTION
This option will print the following statement at the end of a credit card
transaction:
“I AGREE TO PAY ABOVE TOTAL AMOUNT ACCORDING TO CARD ISSUER
AGREEMENT (MERCHANT AGREEMENT IF CREDIT VOUCHER).”
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [6] for Print Disclaimer.
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
PRT DSCLMR1 MODE
Press [1] to turn the Disclaimer Off
3.
1.OFF
2.ON
Or
Press [2] to turn the Disclaimer On
4.
Stop.
User Guide
66
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Menu Type
FUNCTION
DESCRIPTION
The menu in the terminal can be set to scroll automatically, or manually.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [7] to Set Menu Type
Use the [] and [] keys to find your
selection and then press [ENTER].
3.
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
CHOOSE MENU TYPE
1.Auto Scroll
2.Manual Scroll
Or
Press the number corresponding with
your selection.
4.
Note: If auto scroll is selected the terminal will prompt you for scroll speed
(1/fastest-9/slowest). Type in a speed and press [ENTER].
5.
Stop.
User Guide
67
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Halo
FUNCTION
DESCRIPTION
STEP
This option sets a limit that cannot be exceeded. This option can be set for sales,
refunds, and/or cash back.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu press [3] to access
Merchant Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [8] to Set Halo.
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
Use the [] and [] keys to find your
selection and then press [ENTER].
4.
HALO FOR SALE:
1.OFF
2.ON
Or
Press the number corresponding with
your selection
Note: If option 1 is selected, continue with step 6.
HALO: $0.00
NEW RATE: $0.00
5.
Input the maximum amount for a sale
then press [ENTER].
Continued on next page
User Guide
68
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Halo, Continued
STEP
ACTION
DISPLAY
HALO FOR RETURN:
1.OFF
2.ON
6.
Repeat steps 4 and 5 for Return Halo and
Cash Back Halo.
7.
Stop.
User Guide
69
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print Setup
FUNCTION
DESCRIPTION
This option will print a setup report. It will show application information, the
terminal header and trailer, signature capture mode if enabled, list all card types
showing enabled (+) or disabled (-), menu security, card security, paper type,
merchant fee, PIN pad information, server mode, invoice mode, report setup,
HALO settings working mode information, comment line, transaction type settings
and the Hot Key list.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Press [9] to Print the terminal Setup
1.Paper Type
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
ENTER PASSWORD:
3.
Input the Password and press [ENTER].
4.
Stop.
User Guide
70
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Store & Forward
Store & Forward (Offline Mode) will give the following six different options:
FUNCTION
DESCRIPTION
ˆ Mode Select
ˆ Reports
ˆ Resend Failed
ˆ Display Transactions
ˆ Upload Transactions
ˆ Delete Failed
Turning Store & Forward On/Off
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS:
2.
Use the [] key to scroll to menu option
10. Store & Forward and then press
[ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
STORE&FORWARD
4.
Press [1] for S&F On/Off
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
Continued on next page
User Guide
71
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Turning Store & Forward On/Off, Continued
STEP
ACTION
DISPLAY
Store & Forward
Switch ON?
5.
6.
If Store & Forward is ON, [ENTER] will
turn it OFF. If Store & Forward is OFF,
[ENTER] will turn it ON.
Stop.
Mode Select
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu option
10. Store & Forward and then press
[ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
Continued on next page
User Guide
72
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Mode Select, Continued
STEP
ACTION
DISPLAY
STORE&FORWARD
Press [2] for Mode Select.
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
Use the [] and [] keys to find your
selection and then press [ENTER].
MODE SELECT:
4.
Or
5.
1.Stay Online
2.Stay Offline
3.Off Until Btch
4.OfflineOnDmnd
Press the number corresponding with
your selection.
NOTE: See list of definitions on next page.
LIMIT PER CARD ?
Accept?ENTER=Yes
6.
7.
8.
9.
Press [ENTER]
Enter the maximum amount to be
accepted for all Visa transactions then
press [ENTER]. For no limit, press
[ENTER] with no max amount entered.
ENTER MAX AMOUNT
VISA
0.00
Continue for all credit card types.
Enter the maximum amount to be
accepted for all transactions in total then
press [ENTER]. For no limit, press
[ENTER] with no max amount entered.
ENTER MAX TOTAL
0.00
10.
A report listing the individual card and total limit will be printed.
11.
Stop.
Continued on next page.
User Guide
73
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Mode Select, Continued
OPTION
DEFINITION
STAY ONLINE
The Terminal will process transactions only via radio/CDPD signal
or phone line
STAY OFFLINE
The Terminal will process transactions via Offline only, it will not
look for signal or phone line.
OFF UNTIL
BATCH
The Terminal will process transactions via Offline only. When the
[BATCH] key is pressed, the terminal will switch to Online and
transmit all the transactions.
OFFLINE ON
DEMAND
Terminal will process via Online. If no radio/CDPD signal is
obtained, and no phone line is connected, the terminal will prompt:
RETRY OR PROCESS OFFLINE?
User Guide
74
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Display Transactions
FUNCTION
DESCRIPTION
STEP
Allows you to view “STORED” or “FAILED” transactions, by scrolling through
all transactions, by transaction# OR server# (if server mode is on).
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu option
10. Store & Forward and then press
[ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
STORE&FORWARD
4.
Press [3] for Display Trans
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
Continued on next page
User Guide
75
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Display Transactions, Continued
STEP
ACTION
Use the [] and [] keys to find your
selection and then press [ENTER].
5.
DISPLAY
DISPLAY TRANS.
1.Scroll All
5.By Trans. #
Or
Press the number corresponding with
your selection.
Use the [] and [] keys to find your
selection and then press [ENTER].
CHOOSE DATABASE
1.STORED
2.FAILED
Or
6.
Press the number corresponding with
your selection.
7.
Stop.
User Guide
76
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Reports – Store & Forward
FUNCTION
DESCRIPTION
STEP
There are three options for Store & Forward Reports:
‰ 1. Print Status
‰ 2. Print Offline ‰
ACTION
3. Print Failed
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu option
10. Store & Forward and then press
[ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
STORE&FORWARD
4.
Press [4] for Reports
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
Continued on next page
User Guide
77
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Reports – Store & Forward, Continued
STEP
ACTION
DISPLAY
5.
Use the [] and [] keys to find your
selection and then press [ENTER].
Or
Press the number corresponding with
your selection.
REPORTS
1.Print Status
2.Print Offline
3.Print Failed
Note: See option Definitions below.
6.
Stop.
OPTION
DEFINITION
Print Status
A print out of the terminal’s status, i.e.:
Offline Mode or Online Mode.
Print Offline
A report of all transactions entered into the
database in Offline Mode.
Print Failed
A report of all transactions that failed and
were stored.
User Guide
78
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Upload Transactions
FUNCTION
DESCRIPTION
STEP
This function allows you to upload all Offline transactions one
by one, or all at once. If any transactions have failed the
terminal will prompt: PRINT FAILED TRANS?
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu option
10. Store & Forward and then press
[ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
STORE&FORWARD
4.
Press [5] to Upload Transactions
Press [MENU] to upload individual
transactions
5.
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
UPLOAD TRANSCT
ONE=MENU ALL=ENT
Or
Press [ENTER] to upload all offline
transactions
6.
Terminal will contact the host, receive response and print receipts.
7.
Stop.
User Guide
79
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Resend Failed Transactions
FUNCTION
DESCRIPTION
STEP
This function allows you to resend any failed transactions.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu option
10. Store & Forward and then press
[ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
STORE&FORWARD
4.
5.
Press [6] to Resend Failed Transactions.
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
Stop.
User Guide
80
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Delete Failed Transactions
FUNCTION
DESCRIPTION
STEP
This function allows you to Delete any failed transactions.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 10. Store & Forward and then
press [ENTER].
2.No-Paper Mode
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
STORE&FORWARD
4.
Press [7] to Delete Failed Transactions.
1.S&F On/Off
2.Mode Select
3.Display Trans
4.Reports
5.Upload Transct
6.Resend Failed
7.Delete Failed
Delete Failed
ENTR=YES, MENU=NO
5.
Press [ENTER] to delete failed
transactions or press [MENU] to cancel
function.
6.
Stop.
User Guide
81
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Reader
FUNCTION
DESCRIPTION
STEP
This function allows you to setup the check reader or check imager. For
the Nurit 8000 SECURE, the terminal must be place in the Docking
Station and the check reader/imager connected to the station.
Note: Check Imaging is supported by the POS_PLUS application only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 11. Check Reader and then
press [ENTER].
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
If a Check Reader is attached, follow
steps #4 & 5.
4.
ChkRdr Options
1.ChkRdr Type
Be sure the check reader is connected to
the docking station then press [ENTER].
If a Check Imager is attached, skip to
step #6.
Detecting H/Ware
please wait…..
5.
The terminal will detect and initialize the
type of Check Reader you have
connected.
User Guide
82
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Reader, Continued
STEP
ACTION
DISPLAY
ChkRdr Options
6.
7.
Be sure the check imager is connected
to the docking station then press
[ENTER].
The terminal will detect the hardware,
verify that imager is connected and
possibly instruct that the RDM Imager
be turned off then on.
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
RDM Needs to be
Turned OFF & ON
8.
The Check Imager will cycle itself and switch to it’s ready state.
9.
Stop.
Check Imager – Send Images (Bridge)
FUNCTION
DESCRIPTION
STEP
This function allows you upload the check images.
Note: Check Imaging is supported by the POS_PLUS application only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 11. Check Reader and then
press [ENTER].
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
Continued on next page.
User Guide
83
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Send Images (Bridge), Continued
STEP
ACTION
DISPLAY
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
ChkRdr Options
Press [2].
4.
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
ARE YOU SURE?
ENTR=YES, MENU=NO
Press [ENTER].
5.
BRIDGE UPLOAD
Preparing Image
6.
Terminal will begin processing and
sending the check images.
Delete All Imgs?
ENTR=YES, MENU=NO
7.
After a successful upload, delete existing
images. Press [ENTER].
8.
Stop.
User Guide
84
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Send Images (FTP)
FUNCTION
DESCRIPTION
STEP
This function allows you upload the check images.
Note: Check Imaging is supported by the POS_PLUS application only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 11. Check Reader and then
press [ENTER].
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
ChkRdr Options
4.
Press [2].
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
ARE YOU SURE?
ENTR=YES, MENU=NO
5.
Press [ENTER].
Continued on next page.
User Guide
85
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Send Images (FTP), Continued
STEP
ACTION
DISPLAY
FTP: Transmitting
Please Wait . . .
Terminal will begin transmitting the
check images and display message
when complete.
6.
7.
Stop.
Check Imager – Clear Images
This function allows you delete the check images.
FUNCTION
DESCRIPTION
STEP
Note: Check Imaging is supported by the POS_PLUS application only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 11. Check Reader and then
press [ENTER].
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
Continued on next page.
User Guide
86
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Clear Images
STEP
ACTION
DISPLAY
ChkRdr Options
Press [3].
4.
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
ARE YOU SURE?
ENTR=YES, MENU=NO
Press [ENTER].
5.
Deleting Images
Please Wait . . .
6.
Terminal will delete the check images
and display message when complete.
7.
Stop.
User Guide
87
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (Bridge)
FUNCTION
DESCRIPTION
STEP
This function accesses the FTP setup menu allowing editing of the
parameters and setup configuration.
Note: Check Imaging is supported by the POS_PLUS application only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 11. Check Reader and then
press [ENTER].
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
ChkRdr Options
4.
Press [4].
Press [1] to switch communication
format.
5.
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
Setup Menu
1.Upload via Æ
Note: After switching from Bridge to FTP, the
FTP Setup parameters are displayed and
modifiable.
User Guide
88
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (Bridge), Continued
STEP
ACTION
Press [1] to switch communications to
Bridge.
6.
Press [2] to switch communications to
FTP.
DISPLAY
Upload via Bridge
1.Bridge
2.FTP
Press [MENU/ESC] to exit without
change.
7.
Stop.
Check Imager – Setup Menu (FTP)
FUNCTION
DESCRIPTION
STEP
This function accesses the FTP setup menu allowing editing of the
parameters and setup configuration.
Note: Check Imaging is supported by the POS_PLUS application only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [3] to access
Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] key to scroll to menu
option 11. Check Reader and then
press [ENTER].
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
Continued on next page.
User Guide
89
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (FTP), Continued
STEP
ACTION
DISPLAY
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
ChkRdr Options
4.
Press [4].
Press [1] to switch communication
format.
5.
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
Setup Menu
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
Note: When switching from FTP to Bridge,
the remaining Setup parameters are
not applicable and will not be
displayed.
Upload via FTP
Press [1] to switch to Bridge.
6.
1.Bridge
2.FTP
Press [2] to switch to FTP.
Press [MENU] to exit without change.
Setup Menu
7.
Press [2] to print the FTP Setup
information.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Continued on next page.
User Guide
90
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (FTP), Continued
STEP
ACTION
DISPLAY
Setup Menu
8.
Press [3] for the RDM Owner Code.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Setup Menu
RDM Owner Code
9.
Enter Owner Code then press
[ENTER].
Setup Menu
10.
Press [4] for RDM Merchant ID.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Setup Menu
RDM MerchantID
11.
Enter Merchant ID then press
[ENTER].
Setup Menu
12.
Press [5] for FTP Phone Number.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Setup Menu
FTP Phone #
13.
Enter the FTP Phone Number then
press [ENTER].
Continued on next page.
User Guide
91
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (FTP), Continued
STEP
ACTION
DISPLAY
Setup Menu
14.
Press [6] for FTP Host Name.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Setup Menu
FTP Host Name
15.
Enter the FTP Host Name then press
[ENTER].
Setup Menu
16.
Press [7] for the FTP User ID.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Setup Menu
FTP User ID
17.
Enter the FTP User ID then press
[ENTER].
Setup Menu
18.
Press [8] for FTP Password.
1.Upload via Æ
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
Setup Menu
FTP Password
19.
Enter the FTP Password then press
[ENTER].
Continued on next page.
User Guide
92
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (FTP), Continued
STEP
ACTION
DISPLAY
Setup Menu
20.
Press [9] for FTP Send Mode.
2.Print Setup
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
9.FTP Send Mdde
FTP Send Mode
21.
Press [1] to send the images in a batch
or press [2] to send the images
individually.
1-Batch 2-Indiv.
Setup Menu
22.
Press [10] for PPP User ID.
3.RDM Owner Code
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
9.FTP Send Mode
10.PPP User ID
Setup Menu
PPP User ID
23.
Enter the PPP User ID then press
[ENTER].
Setup Menu
24.
Press [11] for PPP Password.
4.RDM Merchant ID
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
9.FTP Send Mode
10.PPP User ID
11.PPP Password
Setup Menu
PPP Password
25.
Enter the PPP Password then press
[ENTER].
Continued on next page.
User Guide
93
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Setup Menu (FTP), Continued
STEP
ACTION
DISPLAY
Setup Menu
Press [12] for RDM Autodial.
26.
27.
28.
Press [1] to turn Autodial or and set the
parameters or press [2] to turn Autodial
off.
Enter the time the Autodial process is to
start then press [ENTER].
5.FTP Phone#
6.FTP Host Name
7.FTP User ID
8.FTP Password
9.FTP Send Mode
10.PPP User ID
11.PPP Password
12.RDM Autodial
Autodial is ON
1-ON , 2-OFF
START AT:
01:00
Note: Remember the terminal has a 24-hour
clock.
STOP AT:
02:00
29.
Enter the time the Autodial process is to
stop then press [ENTER].
START AT:
30.
31.
Enter the interval time then press
[ENTER].
AD INTERVAL (min)
10
Stop.
User Guide
94
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Check Imager – Franking
FUNCTION
DESCRIPTION
Franking is marking the check with an ELECTRONICALLY PRESENTED
message. Use the following step action table to enable/disable Franking.
Note: Not all Check Imagers support Franking.
STEP
ACTION
DISPLAY
MENU SCREEN
1.
From the Main MENU SCREEN press
[3] to access Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS
2.
Use the [] arrow (Forced Key) to scroll
to 11. Check Reader then press
[ENTER]
3.Buzzer Set
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
ChkRdr Options
Press [5].
4.
1.ChkRdr Type
2.Send Images
3.Clear Images
4.Setup Menu
5.Franking
Franking
1.OFF
2.ON
5.
6.
Press [1] to disable Franking or [2] to
enable Franking.
Stop.
User Guide
95
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Signature Option
FUNCTION
DESCRIPTION
This option is used to enable capturing the signature from the touch screen
and printing it on the receipt.
Note: Signature Option is supported by the POS_PLUS application only.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press
[3] to access Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS:
2.
Use the [] arrow (Forced Key) to scroll
to 12. Sign. Option then press [ENTER]
4.Operation Mode
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
12.Sign. Option
ENTER PASSWORD:
3.
Input the Password and press
[ENTER]
Sign. Capt. OFF
1.OFF
2.ON
4.
5.
Press [2] to enable signature capture
then press [ENTER]
Stop.
User Guide
96
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Bridge Communication
FUNCTION
DESCRIPTION
This menu functions allows you to set communication parameters for uploading
captured images to the web via Bridge Communication.
Note: Bridge Communication is supported by the POS_PLUS application only.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press
[3] to access Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS:
2.
Use the [] arrow (Forced Key) to scroll
to 13. Bridge Comm then Press
[ENTER]
5.Battery Saver
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
12.Sign. Option
13.Bridge Comm
PARAMS (Modem)
3.
4.
Select the appropriate communication
parameter (specific to the Bridge) by
pressing [ENTER], then edit as
desired.
1.Phone>
2. Via>Modem
3.Baud>2400
4.Fast Con>No
Stop.
User Guide
97
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Language Setup
FUNCTION
DESCRIPTION
This menu functions allows you to set the Display and Printer Language.
Note: Language Setup is supported by the POS_PLUS application only.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press
[3] to access Merchant Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
MERCH. OPTIONS:
2.
Use the [] arrow (Forced Key) to scroll
to 14. Language Setup then Press
[ENTER]
6.Prt Disclaimer
7.Set Menu Type
8.Set Halo
9.Print Setup
10.Store&Forward
11.Check Reader
12.Sign. Option
13.Bridge Comm
14.Language Set
LANGUAGE SETUP
3.
Press [1] to change the Display
Language or [2] to change the Printer
Language.
1.Display
2.Printer
CHOOSE LANGUAGE
2.ENGLISH
9.SPANISH
4.
Press the number that corresponds with
the desired language.
5.
Stop.
User Guide
98
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
4. Host Parameters
This menu allows you to change host parameters, such as merchant numbers,
terminal IDs, authorization/batch phone numbers and the radio address. Each
host has different individual parameters, which should be changed only if advised
by the processing bank or NURIT technical support. If the terminal capture type is
either Host Manual or Terminal, the AutoDial feature can be activated and the
time/duration can be modified. There are six sub-menus in Host Parameters.
MENU
DESCRIPTION
‰ Host Parameters
‰ Protocol Version
‰ Host Phones
‰ AutoDial Setup
‰ Print EDC Setup
‰ Host Radio Address
Host Parameters
FUNCTION
DESCRIPTION
STEP
This allows you to edit your Host Processor parameters.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [4] to
access Host Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
HOST PARAMS:
2.
Press [1] for Host Parameters
1.Hosts Params
2.Hosts Phone
3.Prnt EDC Setup
4.Protocol Ver
5.AutoDial Setup
6.Host Radio Addr
ENTER PASSWORD:
3.
4.
Input the Password and press
[ENTER]
Use the [] and [] scroll through the
different hosts. Select the desired host
and then press [ENTER].
Or
Press the number corresponding with
your selection.
EDC PARAMETERS
1.Host Name CR
2.Host Name DB
3.Host Name CK
NOTE: The actual Host name will appear on the
display for each EDC Type.
Continued on next page
User Guide
99
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Host Parameters, Continued
STEP
5.
ACTION
Use the [] and [] to scroll through the
different parameters. Find the parameter
that you wish to edit and then press
[ENTER].
Or
Press the number corresponding with
your selection.
DISPLAY
Host Name Credit
1.Client Number
2.Terminal_Number
3.Merchant_Number
4.Enter_EBT_Auth
5.LLI_Number
Note: Parameter names differ by host.
6.
Enter the new parameter information then press [ENTER].
7.
Upon completion of all changes press [MENU]
Press [ENTER] to save the changes
8.
Save Parameters?
ENTR=YES, MENU=NO
Or
Press [MENU] to cancel the changes
9.
Stop.
User Guide
100
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Host Phones
FUNCTION
DESCRIPTION
STEP
This option allows the changing of authorization phone numbers
and batch phone numbers for the host processor.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [4] to access
Host Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
HOST PARAMS:
2.
Press [2] for Hosts Phones
1.Hosts Params
2.Hosts Phone
3.Prnt EDC Setup
4.Protocol Ver
5.AutoDial Setup
6.Host Radio Addr
ENTER PASSWORD:
3.
4.
Input the Password then
press [ENTER]
Use the [] and [] scroll through the
different hosts. Select the host that you
wish to edit phone numbers for and then
press [ENTER].
Or
Press the number corresponding with
your selection.
PHONE MENU:
1.Host Name CR
2.Host Name DB
3.Host Name CK
Note: The actual Host name will appear on the
display for each EDC Type.
PHONE TYPE
5.
To Edit Authorization Phone Numbers
press [1]
Or
1.Auth. Phones
2.Batch Phones
To Edit Batch Phone Numbers press [2]
Continued on next page
User Guide
101
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Host Phones, Continued
STEP
ACTION
Select which phone number you wish to
edit.
6.
To set communication for radio before
phone line, press [4] and skip to
Step #10.
The blinking cursor will be positioned on
the first character of the existing phone
number. Enter the new phone number.
7.
Delete any of the old number with the [BS]
key.
DISPLAY
EDIT PHONE
1.Phone # 1
2.Phone # 2
3.Phone # 3
4.Line B4 Radio
EDIT PHONE
1.Phone # 1
2.Phone # 2
3.Phone # 3
Phone # 1
186654055XX
Upon completion press [ENTER].
Baud Rate:
8.
The existing baud rate will be highlighted,
press [MENU] to keep existing rate or
enter the number that corresponds to the
desired baud rate then press [ENTER].
1.300
2.1200
2.1200
3.2400
4.4800
5.7200
6.9600
7.12200
8.14400
EDIT PHONE
9.
Select the next phone number to be
changed and repeat Steps 7 & 8.
1.Phone # 1
2.Phone # 2
3.Phone # 3
Line Before: OFF
If Line B4 Radio was selected:
10.
Press [1] to verify that the terminal will not
try to communicate via the phone line
before the radio.
Press [MENU] twice and you will be
prompted to save your changes.
11.
1.OFF
2.ON
Save Parameters?
ENTR=YES, MENU=NO
Press [ENTER] to save the changes.
Or
Press [MENU] to cancel the changes.
12.
Stop.
User Guide
102
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print EDC Setup
FUNCTION
DESCRIPTION
STEP
This report prints host information such as merchant numbers,
phone numbers, baud rates, capture type and radio information.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [4] to access
Host Parameters.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
HOST PARAMS:
2.
Press [3] to Print EDC Setup.
1.Hosts Params
2.Hosts Phone
3.Prnt EDC Setup
4.Protocol Ver
5.AutoDial Setup
6.Host Radio Addr
ENTER PASSWORD:
3.
4.
Input the Password then press
[ENTER].
Stop.
User Guide
103
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Protocol Version
FUNCTION
DESCRIPTION
STEP
This displays the protocol/host version. This is mainly viewed by
programmers or Customer Support Representatives.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [4] to access
Host Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
HOST PARAMS:
2.
Press [4] for Protocol Version
1.Hosts Params
2.Hosts Phone
3.Prnt EDC Setup
4.Protocol Ver
5.AutoDial Setup
6.Host Radio Addr
CHOOSE EDC TYPE
3.
Select the EDC Type you would like to
view the Protocol Version for.
Press Any Key to go back to the
previous screen.
2.CREDIT
3.DEBIT
4.EBT
HOST Ver. 00.00
Press Any Key…
4.
Note: The Actual Protocol Version will appear on
the display.
5.
Stop.
User Guide
104
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
AutoDial Setup
FUNCTION
DESCRIPTION
STEP
If the terminal capture type is Host Manual or Terminal Capture,
the AutoDial feature will automatically perform the manual batch
function. If the terminal capture type is Autobatch, this function is
not applicable.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [4] to access
Host Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
HOST PARAMS:
2.
Press [5] to view Autodial Setup
1.Hosts Params
2.Hosts Phone
3.Prnt EDC Setup
4.Protocol Ver
5.AutoDial Setup
6.Host Radio Addr
ENTER PASSWORD:
3.
Input the Password then press
[ENTER].
CHOOSE HOST
4.
Press [1] for ALL or select the desired
host.
1.ALL
2.Credit Host
3.Debit Host
AUTODIAL SETUP
1.OFF
2.ON
5.
Press [1] to turn AutoDial OFF or
press [2] to turn AutoDial ON.
Continued on next page
User Guide
105
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
AutoDial Setup, Continued
STEP
ACTION
If AutoDial was turned on the system will
prompt for the AutoDial start time.
6.
DISPLAY
START AD AT:
03:00
Enter the start time then press [ENTER].
Remember that the terminal has a 24hour (military) clock.
STOP AD AT:
04:00
7.
Enter the stop time then press [ENTER].
Stop time is usually one hour after start
time.
STOP AD AT:
04:00
8.
9.
Enter the AutoDial time interval then
press [ENTER]. The interval is usually 5
minutes.
AD INTERVAL:
5
Stop.
User Guide
106
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Host Radio Address
FUNCTION
DESCRIPTION
STEP
Displays and allows the editing of Host Radio Addresses on
Mobitex and Motient wireless terminals. If the terminal is wireless
CDPD or is not wireless, this function will not be available.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [4] to access
Host Parameters
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
HOST PARAMS:
2.
Press [6] for Host Radio Address.
1.Hosts Params
2.Hosts Phone
3.Prnt EDC Setup
4.Protocol Ver
5.AutoDial Setup
6.Host Radio Addr
ENTER PASSWORD:
3.
Input the Password then press [ENTER]
Radio Addresses
1.Credit Host
2.Debit Host
4.
Select the desired host.
Radio Addresses
Press [1] for Authorization Radio Address
5.
1.Auth. Radio:
2.Batch Radio:
Or
Press [2] for Batch Radio Address.
Continued on next page.
User Guide
107
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Host Radio Address, Continued
STEP
ACTION
Enter the new Radio Address then press
[ENTER]
Or
6.
Press [MENU] to exit function without
modifying.
DISPLAY
Radio Addresses
1.Auth. Radio:
2.Batch Radio:
Host Radio Addr
123456
Note: Radio Addresses should not be modified
without technical advisement.
Press [ENTER] to save the new
parameter
7.
Save Parameters?
ENTR=YES, MENU=NO
Or
Press [MENU] to cancel.
8.
Stop.
User Guide
108
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
5. System Options
This menu consists of twelve different functions that can be changed manually.
MENU
DESCRIPTION
‰ Set Time/Date
‰ Edit Database
‰ PIN Pad Initialize
‰ Edit PIN Key
‰ Working Mode
‰ PIN Pad Function
‰ Sel. Master Key
‰ Test Mode
‰ PIN Pad Config.
‰ Set Batch No.
‰ Predial Call
‰ Status Bar
Set Terminal Time and Date
FUNCTION
DESCRIPTION
STEP
This option allows you to set the time and date in the terminal.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [ENTER] to Set the Time and
Date.
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
05/31/2003
10:02:49
3.
Verify the current Time and Date is
incorrect then press [ENTER] to edit.
SETTING DATE:
MM/DD/YY
4.
Input the correct date using MM/DD/YY
format.
Continued on next page
User Guide
109
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Terminal Time and Date, Continued
STEP
ACTION
DISPLAY
SETTING TIME
hh:mm:00
5.
Input the correct time using Military (24hour) Format
6.
Verify the time and date is now correct and press [MENU]
7.
Stop.
User Guide
110
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit PIN Key
FUNCTION
DESCRIPTION
STEP
This option allows the changing or viewing of the working key for
the PIN pad (access to this menu is not available without a PIN
pad). The only time a change should be made in this field is if
instructed by customer service.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [ENTER] to Set the Time and Date.
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
4.
Place the curser over the number you
wish to edit using the [] and [] keys.
Or
Press [CLEAR] to remove the entire
Working Key, then input the new one.
ENTER PASSWORD:
****
EDIT WORKING KEY
0000000000000000
Upon completion Press [ENTER]
5.
Stop.
User Guide
111
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Select Master Key Location
FUNCTION
DESCRIPTION
STEP
This changes the Master key location (access to this menu is not
available without a PIN pad). Again, this is a field that should only
be changed if instructed by customer service.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [3] to Select Master Key
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
ENTER PASSWORD:
4.
5.
Input the correct Master Key Location
and Press [ENTER]
MASTER LOCATION
0
Stop.
User Guide
112
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Batch Number
FUNCTION
DESCRIPTION
STEP
This menu option allows the batch number to be changed, if
needed. This is also a field that should only be changed when
instructed by customer service. To change the batch number:
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [4] to Set the Batch Number
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
CHOOSE HOST
2.Credit Host
3.Debit Host
4.
Choose Host requiring batch number
change.
Continued on next page
User Guide
113
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Set Batch Number, Continued
STEP
ACTION
DISPLAY
New Batch No:
000000014
5.
Input the New Batch # then press
[ENTER].
Press [ENTER] to complete.
6.
ARE YOU SURE?
ENTR=YES, MENU=NO
Or
Press [MENU] to cancel.
7.
Stop.
User Guide
114
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Database
FUNCTION
DESCRIPTION
This sub-menu has three options, Void Transaction, Clear
Database and Clear Offline. Void transaction will void a
transaction by the transaction number. Clear Database will
delete a batch and all its transactions. Clear Offline will clear
all the offline transactions in the terminal.
Edit Database – Void a Transaction
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press
[5] to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [5] to Edit the Database.
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
EDIT DATABASE
1.Void Transact
2.Clear Database
3.Clear Offline
3.
Press [1]
CHOOSE EDC TYPE
2.CREDIT
3.CASH
4.
Select an EDC Type .
Continued on next page
User Guide
115
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Database – Void a Transaction, Continued
STEP
ACTION
DISPLAY
ENTER PASSWORD:
5.
Input the Password and Press
[ENTER]
ENTER PASSWORD:
****
6.
Input the transaction number to be
voided then press [ENTER].
Transaction # ?
1
#0001
7.
View the transaction on the display to
verify it is the correct transaction then
SL
52.00
Mastercard 0803
Press [ENTER].
Press [ENTER] to complete
8.
Void Trns #1?
ENTR=YES, MENU=NO
Or
Press [MENU] to cancel
9.
Stop.
User Guide
116
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Database – Clearing the Database
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [5] for Edit Database
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
EDIT DATABASE
1.Void Transact
2.Clear Databas
3.Clear Offline
3.
Press [2] to Clear Database
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Press [ENTER] to continue
5.
ARE YOU SURE?
ENTR=YES, MENU=NO
Or
Press [MENU] to cancel
CHOOSE EDC TYPE
Select the EDC type you wish to clear or
press [ENTER] for all EDC types.
6.
1.ALL
2.CREDIT
3.DEBIT
A report stating which databases were
cleared will print.
7.
Stop.
User Guide
117
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Edit Database – CLEAR OFFLINE
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [5] to Edit Database
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
EDIT DATABASE
1.Void Transact
2.Clear Databas
3.Clear Offline
3.
Press [3] to Clear Offline
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Press [ENTER] to continue
Delete Offline?
ENTR=YES, MENU=NO
Or
5.
Press [MENU] to cancel
6.
Stop.
User Guide
118
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode
INFORMATION
This sub-menu has four options:
‰ Tip Options
‰ AVS Options
‰ Card Present Options
‰ Comment Option
Working Mode – TIP OPTIONS
FUNCTION
DESCRIPTION
STEP
This option allows you to include up to three tips per transaction.
This option will also allow you to name the tip type for identification
and set a default tip amount for each tip as desired. All tips will be
processed during the transaction.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [6] for Working Mode
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
WORKING MODE:
3.
Press [1] for Tip Options.
1.Tip Option
2.AVS Option
3.Card Prsnt Opt
4.Cpmment Opt.
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Continued on next page
User Guide
119
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – Tip Options, Continued
STEP
ACTION
Use the [] and [] to scroll through tips
options, find the tip that you wish to edit
and then press [ENTER].
DISPLAY
TIP OPTIONS:
1. Tip 1: (OFF)
2. Tip 2: (OFF)
3. Tip 3: (OFF)
Or
5.
Press the number corresponding with your
selection.
Note: The current status is displayed in parenthesis.
Tip 1 (OFF)
6.
Use the [] and [] to scroll between Off
and On then press [ENTER] to select.
1. OFF
2. ON
Note: After turning a tip option ON you will then be
prompted to edit the Tip name.
7.
Using the method described in Editing
Header, enter the 13-character tip
designation. Press [ENTER] when the
name has been entered.
TIP 1 Name: 1 N
Tip
Press [ENTER] without the modification to
keep the existing name.
If desired, enter the default tip amount
then press [ENTER].
8.
Tip : $0.00
New Rate:
0.00
Or
Press [ENTER] to bypass.
9.
Stop.
User Guide
120
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – AVS OPTIONS
FUNCTION
DESCRIPTION
These options are used for AVS mode. AVS (Address Verification)
will prompt the user for a zip code, and street address.
* There are three options for AVS:
x
x
x
STEP
OFF – no prompt for zip code, or street address
ON MANUAL ONLY – will prompt for zip code and street address on a manual entry only
ALWAYS – will prompt for zip code and street address on swiped and manual entries.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [6] for Working Mode
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
WORKING MODE:
3.
Press [2] for AVS Options.
1.Tip Option
2.AVS Option
3.Card Prsnt Opt
4.Coment Opt.
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Continued on next page
User Guide
121
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – AVS Options, Continued
STEP
ACTION
DISPLAY
Ask for AVS:
Select the desired AVS Option
5.
1. Off
2. Manual Only
3. Always
*Note: See descriptions above
Check rates
with your bank
6.
7.
Press Any Key to Complete
Stop.
User Guide
122
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – Card Present Options
FUNCTION
DESCRIPTION
These options are used for verifying if the card is present at the
point of Sale.
* There are three options for Card Present:
x
x
x
STEP
NO, IF MANUAL – No prompt to verify card is present on a manual entry. Will prompt for
zip code and street address.
ALWAYS YES – No prompt to verify card is present on a manual entry. Will prompt for
zip code only.
ASK, IF MANUAL – Will prompt to verify card is present on a manual entry. Will prompt
for zip code only if card is present or both zip and street address if card is not present.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [6] for Working Mode
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
WORKING MODE:
3.
Press [3] for Card Present Options.
1.Tip Options
2.AVS Options
3.Card Prsnt Opt
4.Comment Opt.
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Continued on next page.
User Guide
123
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – Card Present Options, Continued
STEP
ACTION
Select the desired Card Present
Option.
5.
DISPLAY
Card present:
1.No, if manual
2.Always Yes
3.Ask, if manual
*Note: See descriptions above
Check rates
with your bank
6.
7.
Press Any Key to Complete.
Stop.
User Guide
124
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – Comment Options
FUNCTION
DESCRIPTION
Use this option to add a one line – 24 character comment to the
receipt between the signature line and the trailer.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [6] for Working Mode
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
WORKING MODE:
3.
Press [4] for Comment Options.
1.Tip Options
2.AVS Options
3.Card Prsnt Opt
4.Comment Opt.
ENTER PASSWORD:
4.
Input the Password and press [ENTER]
Comment Opt. 1 N
5.
Using the method described in Editing
Header, enter the 24-character comment
line. Press [ENTER] when the comment
has been entered.
6.
Stop.
User Guide
125
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Predial Call
FUNCTION
DESCRIPTION
The terminal can be programmed to start dialing once the credit card is
swiped. If pre-dial is turned off, the terminal will start dialing after entering
the dollar amount. Ideally, pre-dial saves on transaction time.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [8] for Predial Call
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
ENTER PASSWORD:
3.
Input the Password and press [ENTER]
CHOOSE EDC TYPE:
4.
Select the EDC type you wish to use
Predial for.
1. ALL
2. CREDIT
3. DEBIT
PREDIAL CALL:
1. OFF
2. ON
5.
Use the [] and [] to scroll between Off
and On then press [ENTER] to select.
6.
Stop.
User Guide
126
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Pin Pad Initialization
FUNCTION
DESCRIPTION
This menu will allow you to set the PIN pad initialization to
automatic or manually.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [9] for PinPad Initialize
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
PINPAD INIT. [1]:
3.
Use the [] and [] to scroll between
Auto and Manual then Press [ENTER] to
select.
4.
Stop.
1. Auto
2. Manual
User Guide
127
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Pin Pad Function
FUNCTION
DESCRIPTION
This menu gives option to encrypt terminal manually for the
internal PIN Pad.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Using the [] key scroll down to option #
10. Pin Pad func.
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
10.PinPad Func.
Î
Í
3.
4.
Í Í
Í
Í
Î Î Î
Í Í
Í
Proceed with the regular encryption
process.
Stop.
User Guide
128
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Pin Pad Configuration
FUNCTION
DESCRIPTION
This menu options allows the terminal to be programmed for an
internal PIN Pad or an external PIN Pad.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Using the [] key scroll down to option
# 11. Pin Pad Config. then press
[ENTER] to select.
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
10.PinPad Func.
11.PinPad Config.
ENTER PASSWORD:
3.
Input the Password and Press [ENTER]
Press [1] for internal PinPad
4.
CHOOSE PINPAD:
1- built in 2-ext.
OR
Press [2] for external PinPad
5.
Stop.
User Guide
129
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Status Bar
FUNCTION
DESCRIPTION
This menu options allows you to turn the terminal’s status bar
display off and on.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [5] to access
System Options
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Using the [] key scroll down to option
# 12. Status Bar then press [ENTER] to
select.
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
10.PinPad Func.
11.PinPad Config.
12.Status Bar
STATUS BAR:
3.
4.
Press the number that corresponds with
the desired selection.
1.OFF
2.ON
3.ON with Time
4.ON with Date
Stop.
User Guide
130
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
6. Radio Params
MENU DESCRIPTION
This Menu options allows viewing of the terminals radio
information. There are three sub-menus in the Radio Params
option.
‰ Radio Tests
‰ Print Params
‰ Battery Test
Radio Tests - RADIO RSSI
FUNCTION
DESCRIPTION
This shows the Radio Signal Strength Indicator. The RSSI should
be a thirteen or greater to obtain good reception. The base station
will vary, depending on location.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [6] to access
Radio Params
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
PLEASE WAIT
2.
Allow a few moments for the terminal to
register
RADIO PARAMS:
Press [1] to access Radio Tests.
3.
Press [1] to access Radio RSSI.
1.Radio Tests
2.Print Params
3.Battery Test
RADIO RSSI: 18
BASE STN. : 40
4.
Note: The actual RSSI and base station will
appear on the display.
5.
Press [MENU] to exit
6.
Stop.
User Guide
131
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Radio Tests - TERMINAL MAN# (MOBITEX ONLY)
FUNCTION
DESCRIPTION
This submenu function displays the MAN# (Mobitex Access
Number) assigned to the terminal’s radio.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [6] to access
Radio Params
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
PLEASE WAIT
2.
Allow a few moments for the terminal to
register
RADIO PARAMS:
3.
Press [1] to access Radio Tests.
1. Radio Tests
2. Print Params
3. Battery Test
MAN=55555555
Press any key…
4.
Press [2] for Terminal MAN#.
5.
Press any key to exit.
6.
Stop.
User Guide
132
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Radio Tests - Terminal LLI# (Motient Only)
FUNCTION
DESCRIPTION
STEP
This submenu function displays the LLI# (Logical Link Indicator)
assigned to the terminal’s radio. The LLI must be active on the
Motient network.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [6] to access
Radio Params
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
PLEASE WAIT
2.
Allow a few moments for the terminal to
register
RADIO PARAMS:
Press [1] to access Radio Tests.
1. Radio Tests
2. Print Params
3. Battery Test
3.
RPD ID=11111111
Press [2] for Terminal LLI#.
PRESS ANY KEY…
4.
Note: The RPD ID is the LLI#
5.
Press any key to exit.
6.
Stop.
User Guide
133
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Radio Tests - Radio Information
FUNCTION
DESCRIPTION
This submenu function displays information specific to the units
radio and is used mainly by technical support.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [6] to access
Radio Params
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
PLEASE WAIT
2.
Allow a few moments for the terminal to
register
RADIO PARAMS:
Press [1] to access Radio Tests.
3.
1. Radio Tests
2. Print Params
3. Battery Test
W ID: RIM MASC 0
Press [3] for Radio Info.
EM
4.
Note: Display will differ
5.
Press any key twice to exit.
6.
Stop.
User Guide
134
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Print Params
FUNCTION
DESCRIPTION
This menu options allows you to print the radio parameters set for
the terminal’s radio.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [6] to access
Radio Params
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
PLEASE WAIT
2.
Allow a few moments for the terminal to
register
RADIO PARAMS:
1. Radio Tests
2. Print Params
3. Battery Test
3.
Press [2] for Print Params.
4.
The Radio Parameter information will print out.
5.
Press [MENU] to exit.
6.
Stop.
User Guide
135
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Battery Test
FUNCTION
DESCRIPTION
This submenu function displays the current battery strength.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [6] to access
Radio Params.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
PLEASE WAIT
2.
Allow a few moments for the terminal to
register.
RADIO PARAMS:
1. Radio Tests
2. Print Params
3. Battery Test
3.
Press [3] for Battery Test.
BATT. OK (100%)
GOOD BATTERY
4.
5.
Press [MENU] three times to exit.
Stop.
User Guide
136
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
7. Download
MENU
DESCRIPTION
This Main Menu has four sub-menus pertaining to programming
and reprogramming the terminal. This should only be done under
advisement of customer service. Modem downloads cannot be
done via RADIO and need to be done connected to a telephone
line.
‰ Parameters
‰ Application Only
‰ Autoload
‰ Communication Params
Download Definitions
Parameter
A parameter download is for downloading the merchant’s file into
the terminal. The information being downloaded is merchant
specific. I.e.: Merchant ID, Terminal ID, etc.
Autoload
An autoload is used to update or change the current application in
the terminal in addition to downloading the merchant’s parameters.
I.e.: Retail to Restaurant application would require an autoload.
Application
Only
This option will download only the application information but not the
merchant parameters.
Downloading
FUNCTION
DESCRIPTION
STEP
Refer to above information for download definitions.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [7] to
access the Download Menu
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and press
[ENTER]
Continued on next page
User Guide
137
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Downloading, Continued
STEP
3.
ACTION
DISPLAY
Press [ENTER] to continue
ARE YOU SURE?
ENTR=YES, MENU=NO
Or
Press [MENU] to exit.
4.
To download via current setting
press [ENTER] and skip to step 9.
Or
Press [MENU] to set communication
options.
Through COM1?
ENTR=YES, MENU=NO
Note: The current setting will display
Press [3] to change the download
method.
5.
Note: Continuously pressing [3] will scroll
through the available options.
Whichever option is selected is the
option that will appear on top in
parenthesis.
CONNECT (Modem)
1.Phone>
2.Exchange Pref>
3.Via>Modem
4.Baud>5600
5.Dial>Tone
6.Gateway
7.Suffix
CONNECT (Modem)
6.
7.
8.
If downloading via modem press [1]
and input the download phone
number.
1.Phone>
2.Exchange Pref>
Via>Modem
4.Baud>5600
Enter Phone Num
__
If an exchange prefix is needed press [2] and input the exchange prefix.
And/Or
If a suffix is needed press [7] and input the suffix
Press [MENU] twice after all the communication parameters for the
download have been set.
Continued on next page
User Guide
138
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Downloading, Continued
STEP
ACTION
DISPLAY
Enter Site ID
9.
Input the Site ID for the terminal.
Download
10.
11.
Select the download type by
selecting the number that
corresponds with the appropriate
choice.
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Stop.
User Guide
139
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Communication Parameters, Phone
FUNCTION
DESCRIPTION
STEP
This menu function allows you to set the communication
parameters specifically for downloading the terminal.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [7] to access
the Download Menu
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and press [ENTER]
Press [ENTER] to continue
3.
ARE YOU SURE?
ENTR=YES, MENU=NO
Or
Press [MENU] to exit
18661234567
ENTR=YES, MENU=NO
4.
Press [MENU] to edit the download
phone number.
Enter Phone Num
18661234567
5.
Input the desired phone number for the
download then press [ENTER].
Continued on next page
User Guide
140
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Communication Parameters, Phone, Continued
STEP
ACTION
DISPLAY
Download
6.
7.
Press [MENU] to return to the Download
menu
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Stop.
Download – Comm Parameters, Exchange Prefix
FUNCTION
DESCRIPTION
STEP
This menu function allows you to set a dialing prefix specifically for
dialing out to download only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu press [7] to access
the Download Menu.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and press [ENTER]
ARE YOU SURE?
NO
YES
3.
Press [ENTER] to continue.
Continued on next page
User Guide
141
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Parameters, Exchange Prefix, Continued
STEP
ACTION
DISPLAY
18661234567
ENTR=YES, MENU=NO
4.
Press [ENTER] to continue
Download
5.
Press [4] for Communication Parameters
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
CONNECT (Modem)
6.
7.
Press [2] and then press [ENTER] for
Exchange Prefix
Input the desired exchange Prefix then
press [ENTER]
1.Phone>
2.Prefix>
3.Via>Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
Connect (Modem)
Prefix:
9
Download
8.
9.
Press [MENU] to return to the Download
menu
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Stop.
User Guide
142
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Parameters, Via>
FUNCTION
DESCRIPTION
STEP
This menu function allows you to switch download method. For
example: From Modem to Com1.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu press [7] to access
the Download Menu.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and press [ENTER].
ARE YOU SURE?
NO
YES
3.
Press [ENTER] to continue.
18661234567
ENTR=YES, MENU=NO
4.
Press [ENTER] to continue.
Download
Press [4] for Communication Parameters.
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Continued on next page
User Guide
143
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Parameters, Via>, Continued
STEP
ACTION
DISPLAY
CONNECT (Modem)
Press [3] for Via>Modem
5.
Note: Prompts will vary depending on current
settings.
1.Phone>
2.Prefix>
3.Via>Ext.Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
CONNECT (Modem)
6.
Each time ENTER is pressed the display
will toggle through the available download
methods. Upon the desired setting press
[MENU] to return to the download menu.
7.
Stop.
1.Phone>
2.Prefix>
3.Via>Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
Download – Comm Params, Baud Rate
FUNCTION
DESCRIPTION
STEP
This menu function allows you to change the baud rate (Rate that
data is exchanged between terminal and modem)
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [7] to access
the Download Menu
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and press [ENTER]
Continued on next page
User Guide
144
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Params, Baud Rate, Continued
STEP
ACTION
DISPLAY
ARE YOU SURE?
NO
YES
3.
Press [ENTER] to continue
18661234567
ENTR=YES, MENU=NO
4.
Press [ENTER] to continue
Download
5.
Press [4] for Communication Parameters
Press [4]
6.
7.
Each time [4] is pressed the display
will toggle through the available Baud
Rates for Download. Upon the desired
setting press [MENU] to return to the
download menu.
Stop.
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
CONNECT (Modem)
1.Phone>
2.Prefix>
3.Via>Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
User Guide
145
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Params, Dial>
FUNCTION
DESCRIPTION
STEP
This menu function is specific to the download process it enables
you to switch from Dial tone to Pulse if needed.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [7] to access
the Download Menu
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and Press [ENTER]
ARE YOU SURE?
NO
YES
3.
Press [ENTER] to continue
18661234567
ENTR=YES, MENU=NO
4.
Press [ENTER] to continue
Download
5.
Press [4] for Communication Parameters
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Continued on next page
User Guide
146
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Params, Dial>, Continued
STEP
6.
ACTION
DISPLAY
Press [5]
CONNECT (Modem)
Each time [5] is pressed the display will
toggle from Tone to Pulse.
Upon the
desired setting press [MENU] to return to
the download menu.
1.Phone>
2.Prefix>
3.Via>Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
Note: Prompts will vary depending on current
setting.
7.
Stop.
Download – Comm Params, Gateway>
FUNCTION
DESCRIPTION
STEP
This menu function allows you to set gateway communication
parameters if you are downloading through a gateway.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [7] to access
the Download Menu
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and Press [ENTER]
ARE YOU SURE?
NO
YES
3.
Press [ENTER] to continue
Continued on next page.
User Guide
147
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Params, Gateway>, Continued
STEP
ACTION
DISPLAY
18661234567
ENTR=YES, MENU=NO
4.
Press [ENTER] to continue
Download
5.
Press [4] for Communication Parameters
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
CONNECT (Modem)
6.
Press [6] for Gateway>
1.Phone>
2.Prefix>
3.Via>Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
CONNECT (Modem)
7.
Input the desired Gateway phone
number then press [ENTER]
1.Phone>
2.Exchange Pref>
3.Via>Modem
Gateway:
7.Suffix
Download
8.
9.
Press [MENU] to return to the Download
menu
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Stop.
User Guide
148
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Params, Suffix
FUNCTION
DESCRIPTION
STEP
This menu function allows a suffix at the end of the download
phone number to access an outside line.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [7] to access
the Download Menu
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
ENTER PASSWORD:
2.
Input the Password and Press [ENTER]
ARE YOU SURE?
NO
YES
3.
Press [ENTER] to continue
18661234567
ENTR=YES, MENU=NO
4.
Press [ENTER] to continue
Download
5.
Press [4] for Communication Parameters
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
CONNECT (Modem)
6.
Press [7] and then press [ENTER] for
Suffix>
1.Phone>
2.Prefix>
3.Via>Modem
4.Baud>33600
5.Dial>Tone
6.Gateway
7.Suffix
8.TCP/IP> NO
User Guide
149
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Download – Comm Params, Suffix, Continued
STEP
ACTION
DISPLAY
CONNECT (Modem)
7.
Input the desired Suffix then press
[ENTER]
1.Phone>
2.Exchange Pref>
3.Via>Modem
Suffix:
7.Suffix
Download
8.
9.
Press [MENU] to return to the Download
menu
1.Parameters
2.Autoload
3.Applicat. only
4.Comm. Params
Stop.
User Guide
150
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
8. Communication
This Main Menu has eight sub-menus pertaining to communication.
MENU
DESCRIPTION
‰ Min. Retries ‰ Dial: Tone
‰ Exchange Prefix ‰ Gateway
‰ Suffix
‰ Via Line/Radio ‰ Check Line
‰ Dial Tone Check
Minimum Retries
FUNCTION
DESCRIPTION
STEP
This submenu function allows you to set the amount of times the
terminal dials for authorization or batching.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu press [8] to
access Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
2.
Press [1]
1. Min. retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
COMM MENU
3.
4.
Input the Minimum # of tries then
press [ENTER].
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
Min
Num Tries:
4. Gateway>
15. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
Stop.
User Guide
151
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Dial: Tone/Pulse
FUNCTION
DESCRIPTION
STEP
This submenu function allows you to set the terminal to dial via
pulse or touch-tone.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU:
2.
Press [2] for Dial: options.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
DIAL TYPE:
Press [1] for Tone
3.
1.Tone
2.Pulse
Or
Press [2] for Pulse
4.
Stop.
User Guide
152
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Exchange Prefix
FUNCTION
DESCRIPTION
STEP
This submenu function allows you to program the terminal to dial
an exchange prefix before a phone number, when needed.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
2.
Press [3] for Exchange Prefix.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
EXCHANGE PREFIX
1. No
2. Yes
3.
Press [2] to add an exchange prefix.
EXCHANGE PREFIX
1. No
2. Yes
4.
5.
Input the exchange prefix then Press
[Enter]
ENTER PREFIX:
9
Stop.
User Guide
153
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Gateway
FUNCTION
DESCRIPTION
STEP
This menu option allows you to set communication parameters for
processing transactions through a gateway.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
2.
Press [4] for Gateway.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
Gateway>
1. No
2. Yes
3.
Press [2] then press [ENTER] to input
the gateway phone number.
Gateway>
1. No
2. Yes
4.
5.
Input the Gateway phone number then
Press [Enter]
ENTER GATEWAY:
Stop.
User Guide
154
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Suffix
FUNCTION
DESCRIPTION
STEP
This submenu function allows you to program the terminal to dial a
suffix after a phone number, when needed.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
2.
Press [5] for Suffix.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
SUFFIX>:
1. NO
2. YES
3.
Press [2] then press [ENTER] to add a
suffix.
SUFFIX>:
1. NO
2. YES
4.
5.
Input the Suffix then press [Enter]
ENTER SUFFIX :
__
Stop.
User Guide
155
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Via Line/Radio
FUNCTION
DESCRIPTION
STEP
This will program the terminal to process a transaction by radio
first. If no signal is received, the terminal will look for a phone line.
(This functionality is only available when the NURIT 8000 SECURE
is connected to the external Modem.) If the terminal will only be
using a phone line, because there is no signal in the area, then it
can be programmed for phone Line Only.
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
2.
Press [6] for Via: Line/Radio.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: ON
LINE / RADIO
Press [1] for both Radio and Phone Line.
3.
1. Both
2. Line Only
Or
Press [2] for phone line only.
4.
After the selection has been made press [ENTER]
5.
Stop.
The options are:
Via: Both – Will try to connect via the Radio first then via the phone line if radio is unsuccessful.
Via: Line Only – The terminal will dial out using only a Phone line.
User Guide
156
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
CHECK LINE: ON
FUNCTION
DESCRIPTION
STEP
This menu function tells the terminal to check for a phone line
when attempting to dial out. (This functionality is only available
when the NURIT 8000 SECURE is connected to the external
Modem)
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
2.
Press [6] for Via: Line/Radio.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: OFF
8. D. ToneChk: OFF
COMM MENU
3.
Each time ENTER is pressed the display
will toggle between OFF & ON. Upon
desired setting press [MENU] to go back
to the idle prompt.
4.
Stop.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: OFF
User Guide
157
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
CHECK LINE: ON
FUNCTION
DESCRIPTION
STEP
This menu function tells the terminal to check for a phone line
when attempting to dial out. (This functionality is only available
when the NURIT 8000 SECURE is connected to the external
Modem)
ACTION
DISPLAY
MENU SCREEN:
5.
From the Main Menu Press [8] to access
Communication.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
COMM MENU
6.
Press [6] for Via: Line/Radio.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: OFF
8. D. ToneChk: OFF
COMM MENU
7.
Each time ENTER is pressed the display
will toggle between OFF & ON. Upon
desired setting press [MENU] to go back
to the idle prompt.
8.
Stop.
1. Min. Retries>
2. DIAL : TONE
3. Exchange Pref>
4. Gateway>
5. Suffix>:
6. Via:Line/Radio
7. CHK LINE: ON
8. D. ToneChk: OFF
User Guide
158
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Appendix A – Restaurant Tips and Tabs
Working Mode – TIP OPTIONS
This option allows you to include up to three tips per
transaction. This option will also allow you to name the tip
type for identification. For Tip Discounting, the option must
be enabled for each of the three tips where it is required.
FUNCTION
DESCRIPTION
The default tip amount will automatically be added to the
transaction if a New Rate amount is entered for tips 2 & 3.
For the Tip #1 default tip amount to be added, the tip option
must be set for “In Transaction”.
Note: For Restaurant, Tip #1 cannot be disabled.
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [6] for Working Mode
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
WORKING MODE:
3.
Press [1] for Tip Options.
1.Tip Option
2.AVS Option
3.Card Prsnt Opt
4.Cpmment Opt.
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
Continued on next page
User Guide
159
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – Tip Options, Continued
STEP
ACTION
Use the [] and [] to scroll through tips
options, find the tip that you wish to edit
and then press [ENTER].
5.
Or
Press the number corresponding with your
selection.
DISPLAY
TIP OPTIONS:
1.
2.
3.
4.
Tip 1: (ON)
Tip 2: (OFF)
Tip 3: (OFF)
Tab op
Note: The current status is displayed in parenthesis.
Tip 1 (ON)
6.
Use the [] and [] to scroll between Off
and On then press [ENTER] to select.
1. OFF
2. ON
Note: Though Tip #1 is already on, select on to
continue.
7.
Using the method described in Editing
Header, enter the 13-character tip
designation. Press [ENTER] when the
name has been entered.
TIP 1 Name: 1 N
Tip
Press [ENTER] without the modification to
keep the existing name.
Discounted Tip:
Use the [] and [] to scroll between Off
and On then press [ENTER] to select.
1.OFF
2.ON
8.
Note: To have the tip discount calculated, there
must be a Tip Discount percentage under
Report Setup in the Report Menu.
Use the [] and [] to scroll between the
settings then press [ENTER] to select.
9.
TIP 1 OPTIONS:
1.In Tip Menu
2.In Transaction
3.Auto Percent
Note: See setting description below.
TIP 1 OPTIONS:
10.
If Auto Percent is selected, enter the low
tip percentage then press [ENTER].
1.In Tip Menu
2.In Transaction
3.Auto Percent
LOW % OF SUM
0
Continued on next page.
User Guide
160
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Tip Options, Continued
STEP
ACTION
DISPLAY
TIP 1 OPTIONS:
11.
1.In Tip Menu
2.In Transaction
3.Auto Percent
Enter the high tip percentage then press
[ENTER].
HIGH % OF SUM
0
If desired, enter the default tip amount
then press [ENTER].
12.
Tip : $0.00
New Rate:
0.00
Or
Press [ENTER] to bypass.
13.
Stop.
In Tip Menu – Will not prompt for a tip amount when entering the transaction
and will print a blank tip line on the receipt.
In Transaction – Will prompt for a tip amount when entering the transaction.
Entered amount will print on the receipt. Pressing [ENTER] at prompt
will bypass tip entry and will print a blank tip line.
Auto Percent – Will not prompt for a tip amount when entering the transaction
and will print a blank tip line with suggested tip amount(s) below.
User Guide
161
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Add Tips
FUNCTION
DESCRIPTION
STEP
This menu function allows you to go in and add the tips to a
transaction in the terminal’s database. This is used for Restaurant
transactions only.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [1]
for Add Tips.
2.
There are several options for editing and
adding tips*, use the arrow keys [] []
to make your selection then press
[ENTER].
Or
Press the number corresponding with
your selection.
Use the [] and [] keys to scroll
through the transactions.
3.
When the desired transaction is displayed
press [ENTER] to be prompted to add
the tip amount.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Rprt
Add Tips:
3. Scroll Opened
4. By Server #
5. By Trans. #
6. By Card Type
7. By Card Num.
#0001
VISA
Tip
4.
5.
SL
6.00
1104
: $0.00
2.00
Key in the tip amount then press
[ENTER].
If the amount of the entered tip exceeds
to the Overage Tip parameter (defaults to
20% in the software model), a warning
message is briefly displayed.
Total Tip Exceeds
Tip Limit
Continued on next page.
User Guide
162
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Add Tips, Continued
STEP
ACTION
DISPLAY
Continue ?
ENTER=YES, MENU=NO
6.
Press [ENTER] to accept the overage
amount and continue or [MENU] to
re-enter the tip amount.
Total : $8.00
7.
8.
The total transaction amount will appear
briefly.
Stop
*Note: Scroll Opened will display only untipped transactions and therefore cannot be used
when adjusting a transaction with an existing tip.
User Guide
163
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Working Mode – Tab Option
STEP
ACTION
DISPLAY
MENU SCREEN:
1.
From the Main MENU SCREEN press [5]
to access System Options.
1.Reports
2.Merch. Params
3.Merch. Options
4.Hosts Params
5.System Options
6.Radio Params
7.Download
8.Communication
9.NOS Menu
SYSTEM OPTIONS:
2.
Press [6] for Working Mode
1.Set Time/Date
2.Edit PIN Key
3.Sel. Mstr Key
4.Set Batch No.
5.Edit Database
6.Working Mode
7.Test Mode
8.Predial Call
9.PinPad Init.
WORKING MODE:
3.
Press [1] for Tip Options.
1.Tip Option
2.AVS Option
3.Card Prsnt Opt
4.Comment Opt.
ENTER PASSWORD:
4.
Input the Password and Press [ENTER]
TIP OPTIONS:
Press [4] for Tab Option.
5.
1.
2.
3.
4.
Tip 1: (ON)
Tip 2: (OFF)
Tip 3: (OFF)
Tab Option
Tab Amt: $ 50.00
0.00
6.
7.
Press [ENTER] to keep the current
default tab amount or enter desired
amount then press [ENTER].
Stop.
User Guide
164
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Open a Tab
FUNCTION
DESCRIPTION
STEP
This menu function allows you to start or “open” a tab using a
preset amount.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [2]
for Open a tab.
If the default preset tab amount is correct
press [ENTER] and skip to step 4.
2.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Rprt
Tab Amt:
50.00
ENTR=YES, MENU=NO
Or
If you wish to change the preset amount
press [MENU] and proceed to step 3.
Enter Tab Amt
0.00
3.
Input the correct Tab Amount then press
[ENTER]
Swipe Credit Card
Account ----Æ
4.
Swipe the credit card. Upon approval the
terminal will open the tab and assign it a
number.
If prompted, enter the server ID.
5.
6.
Using the stylus, have the customer
sign on the touch screen display.
Swipe Credit Card
Account ----Æ
ENTER SERVER ID
0
Stop
User Guide
165
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Close a Tab
FUNCTION
DESCRIPTION
STEP
This menu function allows you to close a tab. If tab is more than
preset amount, it will close for full amount, dialing automatically to
host. This will give you two transactions.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [3]
for Close a tab.
2.
There are several options for closing a
tab, use the arrow keys [] [] to make
your selection.
Or
Press the number corresponding with
your selection.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Rprt
Close a tab
3. Scroll Opened
4. By Server #
5. By Trans. #
6. By Card Type
7. By Card Num.
Close a tab
Input the transaction # for the open tab
then press [ENTER].
3.
3. Scroll Opened
4. By Server #
5. By Trans. #
6. By Card Type
Transaction
7. By Card Num.#
?
#0002
OP
Auth. For
MasterCard
0.00
50.00
0803
Note: The display will vary depending on selection
4.
When the open tab displays press
[ENTER] to continue.
Enter Tab Amt
0.00
5.
Input the closing tab amount then press
[ENTER]
Continued on next page
User Guide
166
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Close a Tab, Continued
STEP
ACTION
DISPLAY
Tip
6.
The terminal will process the total tab
amount then prompt you to add a tip
amount.
Input the tip amount then press [ENTER]
:
$0.00
0.00
Total : $60.00
20.00
7.
8.
The total amount will appear briefly and
then the display will return to the idle
Prompt.
Stop
User Guide
167
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Delete a Tab
FUNCTION
DESCRIPTION
STEP
This menu function allows you to delete (void) a tab.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [4]
for Delete a tab.
2.
There are several options for closing a
tab, use the arrow keys [] [] to make
your selection
Or
Press the number corresponding with
your selection.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Rprt
Delete a tab
3. Scroll Opened
4. By Server #
5. By Trans. #
6. By Card Type
7. By Card Num.
Delete a tab
3.
4.
Input the transaction # for the tab you
wish to Void (delete) then press
[ENTER].
When transaction displays press [ENTER]
to continue.
Transaction # ?
#0002 TAB
Auth. For
MasterCard
0.00
50.00
0803
ENTER PASSWORD:
5.
Input the Password and Press [ENTER]
6.
Press [ENTER] for YES
Or
Press [MENU] for NO
Void Trns #2 ?
ENTR=YES, MENU=NO
Note: The actual Trans # will display.
7.
Stop
User Guide
168
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Show Tabs
FUNCTION
DESCRIPTION
STEP
This menu option allows you to scroll through all tabs in the
terminal database.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [5]
for Show tabs.
2.
There are several options for closing a
tab, use the arrow keys [] [] to make
your selection
Or
Press the number corresponding with
your selection.
3.
Use the arrow keys [] [] to scroll
through and view the open tabs in the
terminal’s database.
4.
Press [MENU] to exit.
5.
Stop.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Rprt
Delete a tab
3. Scroll Opened
4. By Server #
5. By Trans. #
6. By Card Type
7. By Card Num.
#0002
OP
Auth. For
MasterCard
0.00
50.00
0803
User Guide
169
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Tab Report
FUNCTION
DESCRIPTION
STEP
This menu option allows you to print a report of all tabs in the
terminal database regardless of their status.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys simultaneously to
access the Tab Menu then Press [6] for
Tab Report.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Rprt
Printing . . . . . . .
2.
3.
The tab report will begin printing.
Stop.
Open Tab Report
FUNCTION
DESCRIPTION
STEP
This menu option allows you to print a report of all open tabs in the
terminal database.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [7]
for Open Tab Report.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
Printing . . . . . . .
2.
3.
The Open tab report will begin printing.
Stop.
User Guide
170
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Close Tab Report
FUNCTION
DESCRIPTION
STEP
This menu option allows you to print a report of all open tabs in the
terminal database.
ACTION
DISPLAY
TAB MENU:
1.
From the idle prompt press the [F] and
[MENU/CANCEL] keys at the same time
to access the Tab Menu then press [8]
for Close Tab Report.
1. Add Tips
2. Open a tab
3. Close a tab
4. Delete a tab
5. Show tabs
6. Tab Report
7. Open Tab Rprt
8. Close Tab Tprt
Printing . . . . . . .
2.
3.
The close tab report will begin printing.
Stop.
User Guide
171
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
POS STD and PLUS - NURIT 8000 SECURE QUICK REFERENCE GUIDE
To access the menu, press the [MENU] key. This key will enter and exit out of the menu. Use the [] and [] key to scroll the menu options.
1. REPORTS
1.
DEFAULT REPORT
Prints programmed default report.
2.
CURRENT REPORT
Prints a report of the current transactions: Offers several options: Used to change default report setup.
3.
HISTORY REPORT
Prints previous batch totals: Prints Combined or Per Batch totals: Maximum of 30 days.
4.
DISPLAY TRANS.
Displays current transactions offering different sorting options.
5.
RECEIPT COPY
Prints a copy of the last approved receipt. (Transaction must be last function performed.)
6.
PERFORMANCE
Prints percentage of Approvals, Denials, Disconnects, Manual Entries and Swipes: Reset option.
7.
TIP REPORT
8.
REPORT SETUP
9.
RAM DISK REPORT *
10.
COMMUNICATIONS
LOG REPORT *
Prints tip details for all servers or a specific server.
Offers option to print Visa/MC transactions together or separately: Setup tip discount.
Prints a report listing the RAM Disk Size and max number of transactions for each EDC type.
Use this function to either print a communication log of the last transaction or batch processed or to
clear the log.
2. MERCHANT PARAMS
1.
AUTHORIZATION
Enables/disables different card and transaction types: Debit mode.
2.
SECURITY LEVEL
Sets security levels for different operations.
3.
EDIT HEADER
Edits the five line, 24 character header.
4.
EDIT TRAILER
Edits the five line, 24 character trailer.
5.
SET CASH EDC
Enables/disables recording of cash transactions.
6.
MERCHANT FEE
Enables and sets the surcharge rate for debit transactions.
7.
SET BATCH TIME
For Host Capture/Autobatch terminals, sets time terminal will print batch report.
8.
SERVER/INVOICE
Enables/disables Server, Invoice, Table and Guest No. Modes. (Table and guest for restaurant only).
9.
SITE ID
View or change Site ID.
3. MERCHANT OPTIONS
1.
PAPER TYPE
2.
NO PAPER MODE
3.
BUZZER SET
4.
OPERATION MODE
5.
BATTERY SAVER
6.
PRINT DISCLAIMER
7.
SET MENU TYPE
8.
SET HALO
9.
PRINT SETUP
10.
STORE & FORWARD
11.
CHECK READER
12.
SIGNATURE OPTION *
13.
BRIDGE COMM *
14.
LANGUAGE SETUP *
Offers choice between single ply, double ply or custom (two receipts for debit).
Disables print function (integrated or stand alone).
Enables/disables tone when pressing keypad.
Toggles between Normal and Demo Modes.
Offers option of turning Radio Only, Terminal Only, Radio and Terminal or neither off after a period of
inactivity.
Enables/disables print of the disclaimer on each receipt.
Toggles between manual scroll and auto scroll.
Maximum dollar limit for a Sale, Return or Cash Back.
Prints terminal setup report listing; Current application, Header, Trailer, Card and transaction types,
Paper type, Surcharge, Security settings, PIN Pad info, HALOs, Modes, Tip settings and Hot Keys.
Enables/disables offline settings: Upload transactions: Resend/delete failed transactions.
Enables/disables check imaging for upload to the Web.
Initializes an E-Pad allowing the capture of signatures for upload to the Web.
Allows communication between terminal and web.
Choose from the available languages for display or printer.
4. HOST PARAMS
1.
HOST PARAMS
Edit parameter settings for all hosts.
2.
HOST PHONES
Edits authorization and batch phone numbers for all hosts.
3.
PRINT EDC SETUP
4.
PROTOCOL VER.
Displays host protocol name and version.
5.
AUTODIAL SETUP
Sets the terminal to automatically dial out for manual batching.
6.
HOST RADIO ADDR.
Prints EDC report listing; EDC types available, All EDC hosts, Capture types, Host parameters, Radio
information (when applicable), AutoDial settings.
Displays programmed host radio address.
Continued on next page.
User Guide
172
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
QUICK REFERENCE GUIDE, Continued
5. SYSTEM OPTIONS
1.
SET TIME / DATE
Sets terminal’s date (mm/dd/yy) and time (hh:mm:00): Clock is 24 Hour/Military time.
2.
EDIT PIN KEY
3.
SEL. MSTR KEY
Edit host processor working key for debit processing.
Change Master Key location.
4.
SET BATCH NO.
Change the current batch number.
5.
EDIT DATABASE
Void transaction: Clear database for selected or all EDC Types.
6.
WORKING MODE
Offers the ability to set: Tip options for retail and restaurant; AVS Option; Card Present Options and
Comment Option.
7.
TEST MODE
8.
PREDIAL CALL
9.
PINPAD INIT.
Initialize external PIN Pad when necessary.
10.
PINPAD FUNC.
Allows encryption of working key in terminal
11.
PINPAD CONFIG.
Toggles between internal or external PIN Pad.
12.
STATUS BAR
Enables and Disables the Status Bar Display.
Programming purposes only.
Enables/disables terminal dialing immediately once card is swiped.
6. RADIO TEST
1.
RADIO TESTS
Mobitex Units: Signal strength; MAN or ILL number; Radio Information
2.
PRINT PARAMS
Mobitex Units: Prints radio type; MAN/LLI number; Radio addresses.
3.
BATTERY TEST
Tests the battery.
7. DOWNLOAD
1.
PARAMETERS
Downloads host and merchant parameters only.
2.
AUTOLOAD
3.
APPLICAT. ONLY
Downloads application only, no host or merchant parameters.
4.
COMM. PARAMS
Sets communication parameters for downloading.
Downloads full application and parameters.
8. COMMUNICATIONS
1.
MIN. RETRIES
Number of times the terminal will call host processor before timeout.
2.
DIAL : TONE
Sets pulse or tone (DTMF) dialing.
3.
EXCHANGE PREF
4.
GATEWAY
5.
SUFFIX
6.
VIA: LINE / RADIO
7.
CHK LINE: ON
8.
D. TONECHK: ON
Enables/disables and stores digit for dialing an exchange prefix before phone number.
Programming purposes only
Enables/disables and stores digit for dialing a suffix after phone number.
Not relevant for the NURIT 2085.
Enables/disables the check line function.
Enables/disables the dial-tone check function.
* NOTE: These features are available with POS_PLUS application only.
User Guide
173
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
BASIC TROUBLESHOOTING
This section briefly describes how to troubleshoot some possible common problems that may
rise during the normal operation of the NURIT 8000 Series. Before requesting service for this
unit, check the list below for a possible cause of the problem you are experiencing. Some
simple checks on your part may solve the problem, and restore proper operation. If you are
still unable to solve the problem, contact the technical support help desk. Do NOT try to solve
the problem by opening the terminal yourself!
Terminal Seems x Try pressing <F> and <MENU> keys simultaneously.
to Have No
x Allow the battery to charge 10 to 12 hours with the terminal on and AC
Power
adapter plugged into the wall (in standby mode).
“NO LINE”
Appears on the
Display
x Make sure that you are receiving radio coverage in the area where you
are located.
Printer Does
Not Function
Properly
x Check that the paper has been fed to the printer properly (underhand).
The NURIT 8000 SECURE uses thermal paper only.
x Check there is paper in the printer compartment. Replace if required.
x If printer continues working even though the paper has been used up,
check that the ‘end of paper’ detector in the printer mechanism is not
blocked by a torn piece of paper.
Card Reader
Not Working
x Make sure that card has been swiped so that its magnetic strip is facing
downward and facing to the front.
x Contact the technical support help desk.
Receipt Prints
“CANCELED”
x The terminal will display a host response, or some type of error
message, as to why the transaction was canceled.
User Guide
174
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Appendix B - Lipman USA Licensing Agreement
8000 Series POS EDC Terminals
END-USER LICENSE AGREEMENT FOR LIPMAN USA SOFTWARE
IMPORTANT-READ CAREFULLY: This Lipman End-User License Agreement (“EULA”) is a legal
agreement between you (either an individual or a single entity) and Lipman USA, Inc. (“Lipman”) for the
Lipman Software Product identified above, which may include associated media, printed materials, and
“online” or electronic documentation (“Software Product”). By installing, copying, or otherwise using the
Software Product, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this
EULA, do not install, copy or use the Software Product and return the product to our attention at the address set
forth below for a full refund.
SOFTWARE PRODUCT LICENSE
The Software Product is protected by copyright laws and international copyright treaties, as well as other
intellectual property laws and treaties. The Software Product is licensed, not sold.
1.
GRANT OF LICENSE. This EULA grants you the following rights:
x Software License. Lipman grants you the non-exclusive right to make and use, solely in connection
with your use of Lipman terminals, a number of copies of the Software Product equal to the number of
Lipman [insert name of terminal] terminals validly purchased by you. You may also make copies of
the Software Product for backup and archival purposes.
x Distribution. Lipman grants you a non-exclusive, royalty-free right to reproduce and distribute an
unlimited number of copies of the Software Product, solely for use in connection with Lipman
terminals, provided that you: (a) distribute the Software Product in object code form only as part of a
software product created by you for use with Lipman terminals, that adds significant and primary value
to the Software Product (the “Licensed Product”); provided such Licensed Product complies with all
applicable laws, rules and regulations, including without limitation, all VISA, MasterCard and other
association rules and regulations; (b) do not use Lipman’s name, logo, or trademarks to market the
Licensed Product; (c) will not permit further distribution of the Software Product by your end-user
customers; (d) include a valid copyright notice on the Licensed Product sufficient to protect Lipman’s
copyright in the Software Product; (e) distribute and license the use of the Licensed Product to end
users only pursuant to your end user license agreement; (f) indemnify, hold harmless, and defend
Lipman from and against any claims or lawsuits, including attorney’s fees, that arise or result from the
use or distribution of your Licensed Product; (g) otherwise comply with the terms of this EVLA; and
(h) agree that Lipman reserves all rights not expressly granted. No license is granted to you in the
source code of the Software Product.
2.
DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.
Not for Redistribution Software. If the Software Product is labeled “Not for Redistribution” or “NFR,” then,
notwithstanding other sections of this EULA, you may not resell, sublicense, or otherwise transfer for value, the
Software Product by itself or as part of a Licensed Product.
Continued on next page
User Guide
175
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Appendix B - Lipman USA Licensing Agreement, Continued
* Maintenance of Copyright Notices. You must not remove or alter any copyright notices on all copies of the
Software Product.
* Limitations on Reverse Engineering, Decompilation, and Disassembly. Neither you nor your end-user
customers may reverse engineer, decompile, disassemble or otherwise attempt to discover the source code of
the Software Product, except and only to the extent that such activity is expressly permitted by applicable law
notwithstanding this limitation.
*Separation of Components. The Software Product is licensed as a single product. Its component parts may
not be separated for use on more than one terminal.
* Performance or Benchmark Testing. You may not disclose the results of any benchmark test of the Software
Product to any third party without Lipman’s prior written approval.
* Support Services. Lipman may provide you with support services related to the Software Product (“Support
Services”), use of Support Services is governed by the Lipman policies and programs described in the user
manual, in “online” documentation, and/or in other Lipman-provided materials. Any supplemental software
code provided to you as part of the Support Services shall be considered part of the Software Product and
subject to the terms and conditions of this EULA. With respect to technical information you provide to Lipman
as part of the Support Services, Lipman may use such information for its business purposes, including for
product support and development. Lipman will not utilize such technical information in a form that personally
identifies you.
Software Transfer. You may permanently transfer all of your rights under this EULA (i) only in conjunction
with a permanent transfer of your validly purchased Lipman terminals; (ii) provided you retain no copies;
(iii) you transfer all of the Software
Product (including all component parts, the media and printed materials, and any upgrades); and (iv) the
recipient agrees to the terms of this EULA. If the Software Product is an upgrade, any transfer must include all
prior versions of the Software Product.
* Termination. Your rights under this EULA terminate upon the termination of your right to use the Lipman
terminal being used in connection with the Software Product. Without prejudice to any other rights, Lipman
may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you
must destroy all copies of the Software Product and all of its component parts.
3.
UPGRADES
If the Software Product is labeled as an upgrade, you must be properly licensed to use a product identified
by Lipman as being eligible for the upgrade in order to use the Software Product. A Software Product
labeled as an upgrade replaces and/or supplements the product that formed the basis for your eligibility for
the upgrade. You may use the resulting upgraded product only in accordance with the terms of this EULA.
If the Software Product is an upgrade of a component of a package of software programs that you
licensed as a single product, the Software Product may be used and transferred only as part of that single
product package and may not be separated for use on more than one terminal.
Continued on next page
User Guide
176
APPLICATION POS-STD AND POS-PLUS - QSP
NURIT 8000 SECURE
Lipman USA Licensing Agreement, Continued
4.
COPYRIGHT
All title, including but not limited to copyrights, in and to the Software Product and any copies thereof
are owned by Lipman or its suppliers. All title and intellectual property rights in and to the content
which may be accessed through use of the Software Product is the property of the respective content
owner and may be protected by applicable copyright or other intellectual property laws and treaties.
This EULA grants you no rights to use such content.
5.
U.S. GOVERNMENT RESTRICTED RIGHTS
The Software Product is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the
Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical
Data and Computer Software Clause at DFARS 252.227-7013 or subparagraphs (c)(1) and (ii) of the
Commercial Computer Software Restricted Rights at 48 CFR 52.227-19, as applicable. Manufacturer
is Lipman USA, Inc., 50 Gordan Drive, Syosset, New York 11791.
6.
EXPORT RESTRICTIONS
You agree that you will not export or re-export the Software Product to any country, person, entity or
end user subject to U.S.A. export restrictions. Restricted countries currently include, but are not
necessarily limited to Cuba, Iran, Iraq, Libya, North Korea, Sudan, and Syria. You warrant and
represent that neither the U.S.A. Bureau of Export Administration nor any other federal agency has
suspended, revoked or denied your export privileges.
7.
NO WARRANTIES.
Lipman expressly disclaims any warranty for the Software Product. THE SOFTWARE PRODUCT IS
PROVIDED “AS IS” WITHOUT WARRANTY OR CONDITION OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. THE ENTIRE RISK ARISING OUT OF USE OR PERFORMANCE OF THE
SOFTWARE PRODUCT REMAINS WITH YOU.
8.
LIMITATION OF LIABILITY
In no event shall Lipman or its suppliers be liable for any damages whatsoever (including, without
limitation, damages for loss of business profits, consequential or incidental damages, business
interruption, loss of business information, or any other pecuniary loss or expense) arising out of the use
of or inability to use the Software Product, even if Lipman has been advised of the possibility of such
damages. Because some states and jurisdictions do not allow the exclusion or limitation of liability for
consequential or incidental damages, the above limitation may not apply to you.
MISCELLANEOUS
This EULA is governed by the laws of the State of New York, excluding the application of its conflict of
laws rules. In the event of any dispute arising from or relating to this EULA, the parties hereto irrevocably
consent to the personal jurisdiction of the courts located in New York, New York, which shall be the
exclusive venue for any such dispute. The United Nations’ Convention on International Sale of Goods does
not apply. This EULA sets forth the entire understanding and agreement between you and Lipman and may
be amended only in a writing signed by both parties.
User Guide
177
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising