Dear User, Much appreciated for purchasing our lock!

Dear User, Much appreciated for purchasing our lock!
Dear User,
Much appreciated for purchasing our lock!
To help you quick understand the operation and have good states of the
lock, please read this manual carefully before use and keep it for further
reference.
This manual introduces the product configuration, function and operation,
installation and maintenance, also FAQ included for your reference and
study.
Please kindly noted this manual applies to I100 series lock only and not
applicable to the others models we produced. Due to the technology
development, we may do some necessary improvement for our product
without notice in advance, but we ensure that the products will be more
excellent and will not affect your use and operation. Please kindly
understand and hope you will enjoy our lock!
Thank you!
Contens
Chapter1
Product Introduction.............................................................. 1
¾ Product structure ........................................................................... 1
¾ Product Features ........................................................................... 2
¾ Door Open Directions & Lock Handle Choice ............................... 4
Chapter2
Operation and Use .............................................................. 5
¾ Keypad & Display Introduce .......................................................... 5
¾ Initial Status ................................................................................... 6
¾ System Reset ................................................................................ 6
¾ User Privilege ................................................................................ 7
¾ Management Menu Diagram ......................................................... 9
¾ Enter Management Menu ............................................................ 10
¾ User management ....................................................................... 11
¾ Set language/date/time/time format/silent mode ......................... 15
¾ Check Record .............................................................................. 17
¾ Expand Function.......................................................................... 18
¾ Unlock Mode................................................................................ 22
¾ Emergency Power Supply ........................................................... 23
¾ Load Batteries and use................................................................ 24
¾ Normal Opening Function............................................................ 24
¾ Keys Alarm Function.................................................................... 24
¾ Tips of Fingerprint Collection ....................................................... 25
Chapter3
Installation ......................................................................... 26
¾ Installation picture........................................................................ 26
¾ Installation step............................................................................ 27
Chapter4
Maintenance and Warranty................................................. 32
¾ Routine Maintenance................................................................... 32
¾ FAQ.............................................................................................. 33
„ Appendix ............................................................................................. 35
♦ Important Notes ........................................................................... 35
œ Technical Parameter .................................................................... 36
œ Principles for Warranty ................................................................ 37
œ Packing list................................................................................... 38
Chapter1
Product Introduction
This chapter will introduce the I100 serial model fingerprint
door lock’s structure, features, function and working
enviroment, it will help you to understand the lock well and
fast.
¾ Product structure
Antenna(Option)
Sliding Cover
Defence function
button
Fingerprint sensor
Battery
Indicator light
Battery Cover
LED display
Knob
Reset button
Touch keypad
Lock body
Lock body
Handle
Handle
key
Screw cover
Emergency power
interface
Indoor
Outdoor
Note: This manual applies to I100 series lock, the pictures aboved for information
only.
1
¾ Product Features
Unlock Mode
Unlock by Fingerprint / Password / Mechanical key
Unlock by Combination mode: Password+Fingerprint; Fingerprint+Fingerprint
Unlock by Remote control(option)
Double Locked Function
The door can be double locked on carry handle inside or outside,
The multi-point mortise, top and bottom bolt will both closed.
Normal Opening Mode(Passage Mode)
This lock can be set to Normal Opening Mode in which state can be directly
down to open the door handle.
Enter Opening mode: After fingerprint or password (except management
password) verification the success, long press numeric keys 9 before opening
the door, system tip operation success, enter normal opening mode, green lights
flashing(about 3 seconds a flash) in this mode.
Cancel Opening mode: You can cancel normal opening mode by opening the
door a either way(except mechanical keys) or taking down the battery power.
Multiple Alram Function
Š
Door not closed competely alarm
Standard: When the door not closed completely and latch bolt under press
status, the lock will sound beeps and red indicator light flashing
after 5 seconds.
Option: Security Manager HSC100 will send the notice message to the
registered mobile phone.
2
Š
Keys unlock alarm
The lock sounds alarm when the door unlocked by any keys.
Š
Tamper alarm
When the lock body be removed or opened by force, It will caused alarm
and the red indicator light keep flashing. The alarm will last 30 seconds.
Note: The alarm can be cleared after unlock operation by any register
fingerprint or password(except key).
Š
Low battery warning
When battery going too low, there is a warning both on the LCD display and
red indicator light. Please replace battery.
Š
False password alarm
Input the error password 3 times or invalid 32 digits in total, the keypad will
auto-locked for 15 minutes. During this period, any operation is invalid and
will lead alarm.
Š
Duress alarm(option)
Duress User ID number: 90-99
When under duress status, the duress finger will activate the alarm and it
will be deal as a background task, the alarm signal will send to the registed
mobile automatically.
Note: The Security Manager HSC100 should be installed and with correctly
registration. For details please refer the Security Manager HSC100
manual.
3
Message Interactive function(option)
The lock connecting with the security manager by wireless.
•
Any unlock operation(except by keys), the security manager will send a
unlock notice message to the registered mobile phone.
•
Tamper alarm, Password breaking alarm and Duress alarm, the security
manager will send alarm notice message to the registered mobile phone.
Note: For details, please refer the security manager HSC100 manual.
¾ Door Open Directions & Lock Handle Choice
— Left open door/Left handle lock
when you stand outdoor, the fixed hinges are on the door left side, that be
defined as a left opening door, it shall matching the left handle lock. which be
further divided into left (push) handle lock and left (pull) handle lock.
— Right open door /Right handle lock:
when you stand outdoor, the fixed hinges are on the door right side, that be
defined as a right opening door, it shall matching the right handle lock. which be
further divided into right(push) handle lock and right (pull) handle lock.
4
Chapter2
Operation and Use
This chapter will introduce the operation of I100 series fingerprint
door lock, include the general function and management setting.
Please carefully remember the registered user’s information.
¾ Keypad & Display Introduce
The I100 mode with touch keypad design, total with 12keys.
Keys & Function:
1. 0~9 digital and letter keys.
2. “3” & “6” integrate the UP/DOWN function;
3. “#” for confirm or wakeup the lock
4. “ * ” for cancel, return to the last level menu and delete user.
Cancel keys “ * ” will be valid when setting user name, user ID number and user
password. It’s not support to cancel the error digital input when unlock by
password!
Note: The touch keypad only working when it be activated.
Activate method: Just touch the kaypad area by hand, the kaypad will
wakeup and the keys will lighting.
5
Just touch the kaypad the kaypad will wakeup
area by hand
and the keys will lighting
¾ Initial Status
—
—
—
—
—
—
Fingerprint record is zero;
Admin password is 00123456;
Time format: 24 hour;
Language: Chinese
Voice: Chinese
Key unlock alarm: Closed
Note: Please to register your own admin password and admin fingerprint as
soon as the lock finished installation.
¾
System Reset
—
—
—
Remove the battery-box cover on the indoor side.
Press and hold the reset button by a needle (as following picture).
The normal password user and fingerprint user will be cleared all.
Admin password renew to the default 00123456.
The Admin fingerprint will still exist after reset operation.
reset button
example
6
Note:
1)
Kindly recommend do reset operation only under status by admin password
forgot. Otherwise it need to re-enroll all user one by one!
2)
System language should be setting after each reset operation or replace
the battery.
¾ User Privilege
Items
Capacity
User ID
Privilege
Admin
Password
1 group
00
add/delete/clear user password, user fingerprint,
remote control; reset admin fingerprint/password;
enroll/cancel Security Manager.
User Password
9 groups
01-09
unlock the door
Admin
fingerprint
1
00
add/delete/clear user password, user fingerprint,
remote control; unlock the door; reset admin
fingerprint/password; enroll/cancel Security Manager.
User
Fingerprint
99
01-99
unlock the door (90-99 also with oblige alarm function )
Admin Mobile
(Option)
1
00
unlock/lock the door,
Security Manager management
Remote control
(Option)
10
00-09
unlock/lock the door
Note:
1.
Password introduce:
a)
Each lock can be store 10 groups(00~09) passwords
b)
The 00 is the default admin ID Number, 01-09 is user ID Number.
c)
Password consists of 8 digits (2 digits ID No.+6 digits password).
Example: Admin password: 00123456.
00 is the ID No., 123456 is the password.
Shall input all the eight digits completly when unlock the door.
d)
The ID no. can’t be repeat(the system will refused enroll automatically).
Each ID No. matching with one group password and only.
7
2.
Fingerprint introduce:
a)
Each lock can be store 100pcs(00~99) fingerprints.
b)
The 00 is the default admin ID Number and 01-99 is user ID Number,
Note: 90-99 are ID number for duress alarm fingerprint.
c)
The ID no. can’t be repeat(the system will refused enroll automatically).
Each ID No. matching with one fingerprint and only.
d)
Fingerprint can’t repeat also(the system will refused enroll automatically).
Each finger should be enroll once and only.
e)
3.
Place your finger for collection or verification when the reader lights on.
The admin password and admin fingerprint is very important and can
support all the management and setting. Such as reset the admin
password/admin fingerprint, add/delete new user and etc.
œ
Please to register your own admin password and admin fingerprint as soon
as the lock finished installation and keep in good memory for futher
management.
8
'r
Management Menu Diagram
II
Mainmenu
I
I
II
II u
II II
I
Reset Admin PW
Reset Admin FP
Add user PW
Add userFP
Delete user PW
Delete user FP
Clear user PW
Clear user FP
I
II II
II II
II
II
II
II
II
About
I
I
Language
Date
Time
Timer format
Mute
I
I
r
Open
records
Resetting
time
I
Check all record
Designate PW
Designate FW
Designate RM
9
User
space
Add remote
Delete remote
Eruoll Sec Mgr
Cancel Sec Mgr
II
¾ Enter Management Menu
Only the admin password and admin fingerprint be allowed to enter the menu.
By admin fingerprint
verify admin fingerprint
By admin password
Verify success,
Press up/down to
press“#” to the
select the menu,
first leve menu
press“#” to enter
Sub-menu
Input admin
Password & press“#”
Note: Move up the sliding cover will automatic wakeup the finger sensor.Also can
press “ # ” to activate the sensor when timeout.
10
¾ User management
Reset admin password
Enter the Sub-menu and select “reset Admin PW” by up/down key and press
“#” to access. Operation interface as follow:
Select the Menu
and press “#”
Input user name Input new password
and press “#”
and press “#”
Repeat input the
Operation
Password and
Success
press “#”
Note:
After reset, the default admin password will be replaced by the new one.
The default admin ID Number is 00, it will offer automatically by system
and can’t be modified.
User name be consist by 0~8 digitals or characters. It’s not obligatory
(The following is the same).
Reset admin fingerprint
Enter the Sub-menu and select “reset Admin FP” by up/down key and press
“#” to the access. Operation interface as follow:
Select the menu Input user Name
and press “#”
and press “#”
Put the same finger to the fingerprint
Operation
reader 3 times for image capture
Success
Note: The admin password Numbers fixed for 00 and can’t be modify.
Please capture the fingerprint when the reader lights on.
11
Add user password
Enter the Sub-menu and select “Add PW” by up/down key and press
“#” to access next menu. Operation interface as follow:
Select the menu
Input user ID NO.
Input user
Input your
and press “#”
or use the default
name and
password and
Repeat the
password
one and press “#”
press “#”
press “#”
and press
“#”
Add user fingerprint
Enter the Sub-menu and select “Add FP” by up/down key and press “#” to
access next menu. Operation is same as the admin fingerprint reset
Operation interface as follow:
Note :
1)
Repeat fingerprint is not allowed, lock will detect that and refuse to register;
2)
90-99 fingerprint ID NO. is for duress fingerprint;
3)
User ID NO. can be input by manual or accept the default one.
12
Delete user password
Enter the Sub-menu and select “Delete PW” by up/down key and press
“#” to access next menu. Operation interface as follow:
Select the menu
and press “#”
Press up/down to choose the password
need be deleted and press “#” to confirm
Delete user fingerprint
Enter the second menu and select “Dele FP” by up/down key and press
“#” to access next menu. Operation interface as follow:
Select the menu
Press up/down to choose the fingerprint user
and press “#”
need be deleted and press “#” to confirm
13
Clear user password (not including admin. password)
Enter the Sub-menu and select “Clear user PW” by up/down key and press
“#” to access next menu. Operation interface as follow:
Select the menu
and press “#”
Choose “enter”+“#”, clear user password,
choose “cancel”+“#” cancel the operation.
Clear user fingerprint (not including admin. fingerprint)
Enter the Sub-menu and select “Clear user FP” by up/down key and press
“#” to access next menu. Operation interface as follow:
Select the menu
and press “#”
Choose “enter”+“#”, clear user fingerprint,
choose “cancel”+“#” cancel the operation.
14
¾ Set language/date/time/time format/silent mode
Please enter the first menu preparing for the follow setting.
Language Setting
Operation interface as follow:
Select “Setting”
Select “Language”
Select the
Operation
and press “#”
and press “#”
language
Success
and press “#”to
confirm
Date setting
Operation interface as follow:
Select “Setting”and Select “Date”
press “#”
Input the year Input the month Input the date
and press “#” and press “#”
and press “#”
and press “#”
Operation
Success
Note: The year should between 2000 to 2099 and others is invalid.
15
Time setting
Operation interface as follow:
Select “Setting”
Select “Time”
Input the hour
Input the minute
Operation
and press “#”
and press “#”
and press “#”
and press “#”
Success
Note: If setting12 hour format that should to select A.M and P.M by button “#”,
any other button is invalid.
Time format setting
Operation interface as follow:
Select “Setting”
Select “Timer format”
Select Timer format
Operation
and press “#”
and press “#”
you want and press “#”
Success
Silent mode setting
Operation interface as follow:
Select “Setting”
Select “Mute”
and press “#”
and press “#”
Press up/down to choose
mute on/off and press“#”
to finish
Note: When the silent function is effective, the alarm sound is still valid.
16
Keys Unlock Alarm Setting:
Operation interface as follow:
Select “Setting”
Select “Key alarm”
Press up/down to choose
Operation
and press “#”
and press “#”
key alarm on/off and
Success
press“#”to finish
Note: When select keys alarm close mode, the lock will no sounds alarm when
unlock by keys.
¾ Check Record(unlock record/reset time/ space remained)
Please enter the first menu preparing for the follow setting.
Open records
z
z
z
z
z
z
Check All: All the records will be list by chronological.
Designate Password User: Input the specific password ID NO.,
Designate Fingerprint User: Input the specific fingerprint ID NO.,
Designate Remote Control: Input the specific remote ID NO.,
Remote unlock records: Check all the records unlock by remote.
Keys unlock record: Check all the record unlock by keys.
Operation interface as follow(to check the designate password for example):
Select “Check”
Select “Open records” Select “designate Input the user ID
Press up/down to
and press “#”
and press “#”
check the record
password” and
press “#”
17
NO. and press
“#”
at different times
Note:
PW----unlock by password;
FP------unlock by fingerprint;
RM-----unlock by Remote Control;
KY-----unlock by Keys.
Reset time record(display the latest one)
Operation interface as follow:
Select “Check”
Select “Resetting time” Display the latest ones
and press “#”
and press “#”
User space (Check user count and space remained)
Operation interface as follow:
Select “Check”
Select “User space” display enrolled password,
and press “#”
and press “#”
fingerprint and the left ones,
Press up/down to check
¾
Expand Function (Remote Control, Security Manager, Combination Mode)
Please enter the first menu preparing for the follow setting.
18
Add remote control
Operation interface as follow:
Select “Expand”
Select “Add
and press “#”
Input user ID NO.Input user name press the key of
remote” and
and press “#”
and press “#”
your remote
press “#”
Note:
1)
The remote control ID NO. can be input by manual from 00-99 and also
can accept the default one;
2)
The remote control can’t be enrolled repeated, the lock will detect
automatically and refused;
3)
If failed caused by overtime or something wrong with the remote control,
please repeat the operation.
Delete remote control
Operation interface as follow:
Select “Expand” Select “Delete remote” Press up/down to choose the remote you
and press “#”
and press “#”
want to delete and press “#” to confirm
19
Enroll Security Manager
Operation interface as follow:
Select “Expand”
Select “Enroll Sec
Input admin phone
and press “#”
Mgr” and press “#”
NO. and press “#”
Success, a confirm
Enrolling…
message will be sent
to the admin phone
Note:
1)
Only administrator’s cell phone NO. can be allowed to manage the
Security Manager HSC100.
2)
The Security Manager HSC100 should be under enroll status.
3)
)
Please do again if shows failed or no reply after 20 seconds.
For details, please refer the Security Manager HSC100 manual.
Cancel security Manager
Operation interface as follow:
Select “Cancel Sec
Choose “Enter”+“#”to confirm
Mgr” and press “#”
“cancel”+“#” to cancel the operation.
Note: Canceled the Security Manager will disable the remote unlock operation,
but alarm function is working still!
20
Add Combination Mode
(Password+Fingerprint, Fingerprint+Fingerprint)
Select”Add
Combination”
and press”#”
Select”PW+FP”
or “FP+FP”
mode, Press “#”
confirm
Input one group
of the registed
password or one
of the registed
Fingerprint, press
“ #” confirm
Input another
Operation
fingerprint that
Success
need to binding,
press”#”confirm
Note:
1)
The combination only available for the users already registed.
2)
Admin password and admin fingerprint is not allowed be combination.
3)
Each password and fingerprint can be combination once and only.
Delete Combination Mode
Select the
Select”Delete
combination need
Combination”
to delete and
and press”#”
™
Operation
Success
press”#”
About the lock itself
verify administrator→press“#”→about →press“#”, it will shows you the
information of the lock.
21
¾ Unlock Mode
Unlock by key
i.
Pull out the key cover by the key hook attached.
ii.
Insert the key and rotating 270 degree, Then turn the lever to unlock the
door.
Note: If the alarm been set, the lock will sounds alarm when unlock by keys.
Unlock by user password
i.
Wakeup the touch keypad, input 8 digit user password(2 ID NO. +6 digit
password), press “#”.
ii.
The green indicator lights on means verify sucessful. Turn the handle to
unlock the door.
Note: Under combination mode, after the password input, it should to vefiry the
fingerprint that be bindinged to unlock the door.
Unlocked by fingerprint
i.
Open sliding cover, the finger sensor will active and lights on, put the
finger on the sensor.
ii.
The green indicator lights on if verify sucessful. Pull down the
lever to open the door.
Note:
1)
The “#” button can activate the lock again if operation timeout(no need
to sliding cover again)
2)
Under combination mode, the 2 different fingerprints in the same group
be required to unlock the door.
22
™
About Combination Mode:
1.
The sequence(who first, who second) for the 2 user in the same group
without limited
2.
The unlock record for the 2 users will both stored in the memory
3.
The notice message in mobile phone will only show one user.
4.
Any user in the combination be deleted, the combination will invalid
automatically; The remained user can unlock the door alone.
Unlock by remote control(optional)
Just for the locks with remote control.
Press unlock/lock button, could unlock/lock the door. Remote control distance
is about 80 meters with the surrounding environment.
¾ Emergency Power Supply
In case that battery runs out and mechanical key has not been taken
along, an external 9V battery (6F22, 9V) can work as an emergency power
supply. Connect it to the interface at the bottom of the exterior assembly to
supply power. And then unlock the door by all the other way.
9V battery (6F22, 9V)
23
¾
Load Batteries and use
Method
A.
loosen the screw and remove the cover.
B.
Put the corresponding battery into the boxes based on the
specifications of the locks.
C.
Fix the cover back.
Notes
—
—
—
—
—
Please use the high quality AA alkaline battery that meet lock requirement;
When out of service for a long period, batteries should be taken out;
Never mix the new AA battery with the used one;
Take out the battery if the lock will in idle long time;
Preserve the environment by handing over the used batteries to the designed
place for reclaim;
— Keep the batteries away from children and pets;
¾ Normal Opening Function
Setting: After fingerprint or password(except the Admin password) verify
successful, press “9” before put down the handle to open the door.
When the green indicate light flash every 3 seconds, it means
normally-open function is activated.
Cancell: Unlock by normal modes (except key), the normal opening mode will
cancell automatically. Or it can be cancelled by reinstall the battery
inside.
¾ Keys Alarm Function
When the setting be activated, any keys unlcok the door will lead alram.
The alarm will last about 30 seconds and can’t be clear, it will auto-stop after 30
seconds.
24
¾ Tips of Fingerprint Collection
The principle of fingerprint identify technology that is comparing the features from the
2 different templates of the same finger, so collect the fingerprint correctly will
significant enhance the success rate of verification.
Method: put the finger on the reader moderately. Refer to the following figures:
OK
NO
NO
OK
NO
NO
OK
OK
NO
NO
25
Installation
Chapter3
This chapter will introduce the installation of I100 series.
¾ Installation picture
13
12
01 Door Frame
11
02 Striking box
10
03 Striking Plate
04 Screw
05 Bottom Latch
06 Mortise
07 Door
08 Spindle
09 Lock body(Outside)
10 Top Latch
11 Spindle holder
12 Lock body(Inside)
13. Screw
08
04
01
02
05 06
07
03
26
09
¾ Installation step
Step 1 Drilling Holes on the Door
This product is applicable for wooden doors and burglarproof doors. The hole
pattern picture 1 is as follows (please follow the 1:1 template in the packing list):
picture1
27
Step 2 Drilling Holes for Striking Box
As shown in picture 2, process the striking hole and make sure that it is at the same
height with the lock and that it aligns with the edge of door when closed.
Tapping screw for wooden door
Metric screw for iron door
A
15
2.5
88.8
95.8
162.8
240.5
26.5
18
A
Section A-A
picture2
Step 3 Determine the direction of mortise
As shown in the picture 3 confirm the position of Latch bolt first before install the
Mortise. If it is in the opposite position, loosen the Latch bolt fixing screw first and
then pull the latch bolt out and rotate it by 180 degrees, then fix it and tighten the
screw.
Rotating position
Latch bolt fixing screw
Picture 3
28
Step 4 Determine the unlock direction
slid the slider according to the direction of arrow,
Rotating handle can adjust the direction of door opening
picture 4
Step 5 Fix mortise
As shown in the picture 5, use tapping screw to fix mortise and top/bottom bolt on
the door.
top bolt
door
mortise
tapping screw
bottom bolt
picture 5
29
Step 6 Fix the spindle
As shown in the picture 6, install the spindle head on the door aim to the mortise hole
and put into the hole on the door.
fixing screw
spindle
spindle head
spindle
door(inside)
picture 6
Step 7 Install exterior and interior
As shown in the picture 7, put the exterior wire harness through the hole to the
back side door then connect with the power wire, then aim the interior lever hole
to the spindle, knob to the mortise hole, use screw to fix exterior and interior
assembly and install the battery cover and insert the cover plug.
Lock body
Power Cable
Lock body(Inside)
Spindle
Screw M6
Screw M4
Door
Spindle Holder
Battery box Cover
Screw Cover
Picture 7
30
Step 8 Install striking box and striking plate
As shown in the picture 8, install striking box on the door frame and install the
striking plate, use four screws to fix it check and make sure that the mortise works
well at last.
Tapping screw for wooden door, metric screw for iron door.
Striking box
Striking plate
door
frame
Fix with screws
Picture8
Step 9 Adjustment
When the lock is fixed on the door, please adjust it as Chapter 2 till the lock works
well.
Notes for Installation
‹
Check the door thickness before installation whether it is within the
requirements. I100 series are applicable for door thickness of
‹
40-100mm.
Do not press the internal wire harness when fixing assemblies.
‹
During installation, handle the lock carefully so as not to scratch the
assemblies.
31
Chapter4
Maintenance and Warranty
This chapter will introduce the maintenance and FAQ of I100
Series fingerprint door lock.
¾ Routine Maintenance
The lock face is prohibited to contact with corrosive substances so as not to damage
the prevention layer of the lock face and affect the glossiness of lock face.
The lever is a key part of the door lock, and its performance will directly influence its
operation. Do not hang any objects on the lever.
If the door is deformed, the friction between bots and striking box will be enlarged and
the bolt cannot extend fully. Hereby, the position of door striking plate should be
adjusted.
The surface of reader will be dirty or wet after use of a long time. Here, you can wipe
off the dirt with a dry and soft cloth.
Please according to the specific models to replace the AA batteries timely when low
battery warning has been heard. Pay attention to the positive and negative poles of
batteries during replacement.
Please keep the mechanical key well.
Do not use any hard and sharp object, including fingernail, to scratch the reader.
Put the finger flat on the reader during acquisition and verification.
If the lock can not be rotated flexibly or the lock can not be kept in correct position, you
should invite the professionals to fill the mortise with mechanical lubricant.
Ensure that transmission part of the assemblies with lubricant to maintain its
smoothness and extend its lifetime. It is recommended to check the screw condition
once every six months or one year.
Add some graphite powder or pencil powder to the keyway regularly (six-month or one
year) or when the key cannot inserted or pulled out smoothly. However, any oil is
rejected so as to prevent the grease sticking the ball spring and the cylinder cannot
rotate and unlocked.
32
¾ FAQ
Problem
1. After successfully
fingerprint/password/
remote control verification,
the green LED light will be on but
the door can not be opened.
Cause
①Incorrect installation of
lock.
②Mechanical problems of
mortise or the lock cylinder
wire harness is damaged or
installed incorrectly.
Please turn to
professionals for help.
①Use the wrong key.
Use correct
mechanical key.
Try to open the door
first, and ask a
professional to check
the lock and replace
the damaged parts with
new ones.
②The cylinder is damaged.
2. Can not unlock the door
by mechanical key.
③The mortise is damaged.
④There are some mechanical
problems with clutch.
①This fingerprint has not
been enrolled.
②This fingerprint has been
deleted.
③The position of the
effective fingerprint is offset
too much.
④This fingerprint is damaged.
3. After fingerprint verification, it is
indicate that the verification is
failed
Solution
⑤The finger is too dry or wet
or cold.
⑥Press the reader too
Tightly so that the
fingerprint is deformed.
⑦Press the reader too
slightly and most of the
finger is not on the reader.
⑧Influenced by direct
sunlight.
33
Unlock the door with
enrolled fingerprint or
by the other way.
Verify the fingerprint
again. Put the finger
flat on the reader and
narrow the distance
between reader and
finger, or unlock the
door by other way.
Enroll other fingerprint
(It is recommend that
One user enroll over 2
fingerprints); or unlock
the door by other way.
Keep the finger
wet\dry\warm, before
verification or unlock
the door by other way.
Use the correct way to
verify the fingerprint
again.
Use any opaque object
to cover the light and
then verify the
fingerprint.
Problem
4. Rotate the exterior lever,
but the latch can not retract
completely.
5. After verification of
enrolledpassword/fingerprint/
remote control, the motor is not
activated and the door
can not be unlocked.
Cause
① Dirt bonded on parts has
blocked the cylinder.
② Top and bottom bolt are
loosen
①The connection wire is
loosened.
② Problems with motor.
①The batteries run out or the
positive and negative
poles are reversed.
6. No response from keypad.
7. After verification of
enrolled password/fingerprint/
remote control, the motor is
activated, but the
exterior lever turns
uselessly, and the door cannot be
unlocked.
8. The door lock is in
normally-open or
normally-closed status,
and cannot be used
normally.
9. Can not unlock/lock the door by
remote control
②The keypad locked
automatically after input the
wrong password 3 times or 32
digit password
③The connection wire
harness for exterior and
interior assemblies is
loosened.
Solution
Please turn to
professionals for help.
Ask a professional to
check the door lock
and replace the
damaged parts.
Check the battery after
unlocking the door by
emergency power
supply or by other way.
Operating the lock 15
minutes later, or unlock
the door by other way.
Ask professionals to
check the lock after
unlocking the door by
mechanical key.
①The lever does not return
when verifying.
Verifying after returning
the lever.
②No mounting spring is
installed in the lever.
Ask professionals to
check the lock.
①Problems with clutch.
②No mounting spring is
installed in the lever.
① The power is run out or
remote control is broken(no
light responding)
② Something wrong with the
lock (remote light is on)
34
Ask professionals to
check the lock.
Replace the battery or
ask professionals to
check the remote
control.
Ask professionals to
check the lock.
„ Appendix
♦ Important Notes
1.
Fingerprint lock is a kind of high-tech product, The installation always direct
impact on the operation and service life of the lock. We stronly recommend to
install the lock by professional person.
2.
Kindly recommend to install the lock after room decoration. That will avoid the lock
surface be damaged and also protect the lock from influenced by the wet paint.
3.
After installation and test, please clear all users information (Fingerprints and
Password) in the lock memory, then register your own admin password and admin
fingerprint at the first time.
4.
To avoid any inconvenience caused by the flat battery, please replace new
5.
If you are going for long trip or the lock will unused long time, please carry the
batteries as soon as the low voltage alarm happens.
keys along with you, and remove the batteries to ensure the service life of the
lock.
6.
If the user have bad quality fingerprint, we recommend to try the thumb and each
user to register 2 fingers.
7.
User capacity: Fingerprint 100pcs; Password 10 groups(8 digits each). Remote
Control: 10pcs.
8.
Please record clearly all the user information and fill in the Registration Form for
further management as below.
9.
Factory default: administration password is 00123456, no fingerprint in memory.
24 hour time format.
35
œ Technical Parameter
No.
Item
Technical Parameters
1
Sensor resolution
2
Anti-sabotage ability of sensor
3
Start-up time
≤ 5 second
4
Contrast
1:N
5
FRR
≤1%
6
FAR
Enrolled information and other
settings
≤0.0001%
The information will not lose when out of
power or replacing batteries.
8
Search angle
360°
9
Fingerprint update model
Auto update
10
Fingerprint template capacity
100
11
Password setting
Random combine
12
Password length
8 digits ( 2 digits ID NO. + 6 digits
password)
7
Bright background, 500dpi
Free of damage by 1000 times of
continuous impact with a 4H pencil 20cm
away.
13
Password capacity
10 groups
14
Remote control capacity(Option)
10
15
Cell Phone Capacity
Depends on the security manager
HSC100’s capacity
16
Voice Prompt
Human Voice
17
Operating system
Double circuits
18
Power supply
AA batteries 2 groups each group
contains 4 PCS
19
Operating voltage
6V
20
Emergency power supply
9V DC
21
Lifetime of battery for fingerprint
5,000 times to unlock the door
22
Lifetime of battery for password
6,000 times to unlock the door
23
Low battery warning
4.8±0.2V
24
Static power consumption
25
Dynamic power consumption
≤ 130 μA
<250mA
26
Anti-static
8KV for touch discharge, and 15KV for
air discharge.
36
No.
Item
Technical Parameters
27
Operating temperature
28
Operating humidity
-10℃ to 55℃
10% to 90%
29
Storage temperature
-20℃ to 70℃
30
Light interference
31
Reader
Avoid strong direct light.
Hard glass, nano-finish surface,
extremely resistant to friction.
32
Open door direction
Left handed and right handed
Note: Parameters subject to change without prior notice for technology innovations
by the company.
œ Principles for Warranty
Our company offers lifelong maintenance for the products. The warranty period free
of charge is within one year from the date of purchase. When the warranty period is
expired, the maintenance fee will be charged for the products.
As for the following situations, the free maintenance service will not be offered:
1
The products without warranty card or any valid purchase certificate; or the
warranty or purchase certificate do not conform with the products;
2
Damage caused byanthropicfactor including the unnormal working
environment, incorrect operation mode or bad quality battery.
3
Disassembly, repair or any change for the lock without unauthorized.
4
Damaged by force majeure.
37
œ Packing list
No.
Name
Amount
01
Exterior assembly
1
02
Interior assembly
1
03
Mortise
1
04
Striking plate
1
05
Striking box
1
06
Cross head screw(optional)
4
07
Spindle(optional)
2
08
Screws for mortise and striking plate
(optional)
8(iron door)
6(wooden door)
09
Exterior shim plate
1
10
Interior shim plate
1
11
Mechanical key
1
12
User manual
1
13
Template
1
14
Service Card
1
15
Certificate of quality
1
16
Battery
17
Spindle head
AA battery (8pcs)
1
Note: The list above is the basic configuration for the I100 series, the actual list
may little difference just subject to the real product.
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement