Portable Projector User`s Manual

Portable Projector User`s Manual
Portable Projector
VT46
User’s Manual
Important Information
RF Interference
Safety Cautions
Precautions
WARNING
The Federal Communications Commission does not allow any
modifications or changes to the unit EXCEPT those specified
by NEC Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could void your right to
operate this equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Please read this manual carefully before using your NEC VT46 Projector and keep the manual handy for future reference. Your serial number
is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power
outlet.
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the
unit may be sufficient to cause electrical shock. Therefore, it is
dangerous to make any kind of contact with any part inside of
the unit.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
This symbol alerts the user that important information concerning the operation and maintenance of this unit has been
provided.
The information should be read carefully to avoid problems.
• Consult the dealer or an experienced radio / TV technician for
help.
In UK, a BS approved power cable with moulded plug has a Black (five
Amps) fuse installed for use with this equipment. If a power cable is not
supplied with this equipment please contact your supplier.
WARNING
TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD
OR IN AN OUTLET UNLESS ALL TWO PRONGS CAN BE FULLY
INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
DOC Compliance Notice
1. For best results, use your projector in a darkened room.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
2. Place the projector on a flat, level surface in a dry area away from
dust and moisture.
Acoustic Noise Information Ordinance-3. GSGV:
3. Do not place your projector in direct sunlight, near heaters or heat
radiating appliances.
The sound pressure level is less than 70 dB (A) according
to ISO 3744 or ISO 7779.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
CAUTION
• Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily
sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The
static background from previous images will disappear.
• Do not put the projector on its side when the lamp is
turned on.
Doing so may cause damage to the projector.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the
projector and the installation must be in accordance with any
local building codes.
d. Please consult your dealer for more information.
E-2
Fire and Shock Precautions
What's in the Box?
1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow
at least 3 inches (10 cm) of space between your projector and a
wall.
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to
ship your VT46 Projector.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver
into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified
NEC service personnel.
Lens cap
(24F38091)
3. Do not place any liquids on top of your projector.
Projector
20
LT
O
M nO
C
R
6. Do not cover the lens with the supplied lens cap or equivalent while
the projector is on. Doing so can lead to melting of the cap and
possibly burning your hands due to the heat emitted from the light
output.
32
5. Keep any items such as magnifying glass out of the light path of the
projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out
of the lens, can cause unpredictable outcome such as fire or injury
to the eyes.
S JAPAN H
4. Do not look into the lens while the projector is on. Serious damage
to your eyes could result.
2- L iC E L L 3 V
Remote control
(7N900421)
Lithium battery
(CR2032)
Power cable
(US:7N080206)
(EU:7N080005)
RGB signal cable
(7N520012)
Soft carrying case
(24BS7201)
CD-ROM
User’s manual
7. The projector is designed to operate on a power supply of 100-120
or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this
requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time,
disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can
cause electrical shock or fire.
CAUTION
1. Do not try to touch the ventilation outlet on the left side (when seen
from the front) as it can become heated while the projector is turned
on.
2. Do no use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
3. Enable High-Speed Fan mode if you continue to use the projector
for consecutive days. (From the menu, select [Advanced] → [High
Speed Fan Mode].)
4. Do not unplug the power cable from the wall outlet under any one of
the following circumstances.
Doing so can cause damage to the projector:
•
To replace the lamp, follow all instructions provided on page E-25.
•
Be sure to replace the lamp when the message "The lamp has
reached the end of its usable life. Please replace the lamp."
appears. If you continue to use the lamp after the lamp has reached
the end of its usable life, the lamp bulb may shatter, and pieces of
glass may be scattered in the lamp case. Do not touch them as the
pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
•
Allow a minimum of 60 seconds to elapse after turning off the projector. Then turn off the main power switch, disconnect the power
cable and allow 60 minutes to cool the projector before replacing
the lamp.
E-3
e
te
an
ar icy
Gu pol
Lamp Replacement
nt
rta on
po ati
Im rm
fo
In
While the Hour Glass icon appears.
While the cooling fans are running. (The cooling fans continue
to work for 60 seconds after the projector is turned off).
k
ic t
Qu nec
n e
Co uid
G
*
*
TABLE OF CONTENTS
Important Information ........................................... E-2
MAINTENANCE ................................................... E-25
Safety Cautions ........................................................................................... E-2
What's in the Box? ...................................................................................... E-3
Replacing the Lamp ...............................................................................
Cleaning ..................................................................................................
Cleaning or Replacing the Filter ........................................................
Cleaning the Cabinet and the Lens ....................................................
INTRODUCTION .................................................... E-5
Introduction to the Projector ....................................................................... E-5
Part Names of the Projector ........................................................................ E-6
Top Features ............................................................................................. E-7
Terminal Panel Features ........................................................................... E-8
Part Names of the Remote Control ........................................................... E-8
Battery Installation ................................................................................ E-9
Remote Control Precautions ................................................................. E-9
Operating Range for Wireless Remote Control ..................................... E-9
E-25
E-26
E-26
E-26
TROUBLESHOOTING .............................................. E-27
Power Indicator ......................................................................................... E-27
Status Indicator ......................................................................................... E-27
Lamp Indicator .......................................................................................... E-27
Common Problems & Solutions ................................................................ E-28
SPECIFICATIONS ................................................. E-29
INSTALLATION AND CONNECTIONS ............................. E-10
APPENDIX ......................................................... E-30
Setting Up the Screen and the Projector ................................................... E-10
Selecting a Location ............................................................................... E-10
Throw Distance and Screen Size ............................................................ E-11
Making Connections .................................................................................. E-12
Connecting Your PC or Macintosh Computer ......................................... E-12
To connect SCART output (RGB) ............................................................ E-12
Connecting Your DVD Player .................................................................. E-13
Connecting Your VCR or Laser Disc Player ............................................ E-14
Connecting the Supplied Power Cable .................................................... E-14
Cabinet Dimensions .................................................................................. E-30
Pin Assignments of D-Sub RGB Input Connector ...................................... E-30
Compatible Input Signal List ..................................................................... E-31
PC Control Codes ...................................................................................... E-32
Cable Connection ...................................................................................... E-32
TravelCare Guide ....................................................................................... E-33
PROJECTING AN IMAGE (BASIC OPERATION) ................. E-15
Turning on the Projector ............................................................................ E-15
Selecting a Source ..................................................................................... E-15
Adjusting the Picture Size and Position .............................................. E-16
Correcting the Vertical Keystone Distortion ......................................... E-16
Optimizing RGB Picture Automatically ............................................... E-17
Turning Up or Down Volume ..................................................................... E-17
Turning off the Image and Sound ............................................................ E-17
Turning off the Projector ......................................................................... E-17
USING ON-SCREEN MENU ....................................... E-18
Basic Menu Operation ............................................................................... E-18
Using the Menus .................................................................................... E-18
List of Menu Items .................................................................................... E-19
Menu Elements .......................................................................................... E-20
Menu Descriptions & Functions ................................................................ E-21
Picture .................................................................................................... E-21
Brightness/Contrast/Sharpness/Color/Hue ......................................... E-21
Picture Management ........................................................................... E-21
Image ..................................................................................................... E-21
Correcting Vertical Keystone Distortion [Keystone] ...................... E-21
Saving Vertical Keystone Correction [Keystone Save] .................. E-21
Selecting Aspect Ratio [Aspect Ratio] .......................................... E-22
Adjusting the Vertical Position of Image [Cinema Position](for Cinema only) .. E-22
Setup .................................................................................................... E-22
Selecting Menu Language [Language] ............................................ E-22
Selecting Menu Color [Menu Color Select] .................................... E-22
Selecting Menu Display Time [Menu Display Time] ..................... E-22
Selecting a Color or Logo for Background [Background] ................. E-22
Selecting Projector Orientation [Orientation] .............................. E-22
Advanced ............................................................................................. E-22
Security ............................................................................................ E-22
Disabling the Cabinet Buttons [Control Panel Key Lock] ............. E-23
Enabling High Speed Fan Mode [High Speed Fan Mode] ............... E-23
Selecting Signal Format [Signal Select] ....................................... E-23
Page2 ................................................................................................ E-23
Enabling Power Management [Power Management] ...................... E-23
Selecting Noise Reduction Level [Noise Reduction] ................... E-23
Enabling Auto Adjust [Auto Adjust] ................................................ E-24
Adjusting Position/Clock (when Auto Adjust is off) ..................... E-24
Selecting Communication Speed [Communication Speed] .......... E-24
Information ......................................................................................... E-24
Default ................................................................................................. E-24
Returning to Factory Default [Factory Default] ............................. E-24
Resetting the Filter Usage Hours [Clear Filter Usage] ................. E-24
Clearing Lamp Hour Meter [Clear Lamp Hour Meter] ...................... E-24
E-4
INTRODUCTION
Introduction to the Projector
About this user's manual
This section introduces you to your new VT46 Projector and describes
the features and controls.
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review
the user's manual. This may save you time later on. At the
beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it.
Congratulations on Your Purchase of The VT46
Projector
The VT46 is one of the very best projectors available today. The VT46
enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, document camera, or a laser disc player.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen, and the projector can be
permanently mounted on a ceiling*1. The remote control can be used
wirelessly.
*1 Do not attempt to mount the projector on a ceiling yourself.
• IBM is a trademark or registered trademark of International Business
Machines Corporation.
• Mac and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
• Windows, Windows 98, Windows Me, Windows XP or Windows 2000
are trademarks or registered trademarks of Microsoft Corporation.
• Other product and company names mentioned in this user’s manual
may be the trademarks or registered trademarks of their respective
holders.
The projector must be installed by qualified technicians in order
to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local
building codes. Please consult your dealer for more information.
Features you'll enjoy:
• Keystone correction allows you to correct trapezoidal distortion so
that the image is square.
• Low level operation noise
• Short focal length lens
• 160W lamp
• Direct keys for source selection
• New Color Management system
• New menu design improves operation
• NEC’s exclusive Advanced AccuBlend intelligent pixel blending technology - an extremely accurate image compression technology - offers a crisp image with UXGA (1600⳯1200) resolution*2.
• Supports most IBM VGA, SVGA, XGA , SXGA/UXGA(with Advanced
AccuBlend)*2, Macintosh, component signal (YCbCr/ YPbPr) or any
other RGB signals within a horizontal frequency range of 24 to 100
kHz and a vertical frequency range of 50 to 120 Hz. This includes
NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 standard video signals.
*2 A UXGA (1600⳯1200), SXGA (1280⳯1024) and XGA
(1024⳯768) image are displayed with NEC’s Advanced
AccuBlend.
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
• The supplied remote control can be used without a cable.
• You can control the projector with a PC using the PC Control port.
• The contemporary cabinet design is light, compact, easy to carry,
and complements any office, boardroom or auditorium.
E-5
Part Names of the Projector
Monaural Speaker (1W)
Controls (See page E-7)
Zoom Lever
Lamp Cover (See page E-25)
Focus Ring
Lamp Cover Screw
Lens
Ventilation (outlet)
Heated air is exhausted from here
Adjustable Tilt Foot Lever
(See page E-16)
Adjustable Tilt Foot
(See page E-16)
Adjustable Tilt Foot Lever
(See page E-16)
Lens Cap
Adjustable Tilt Foot (See page E-16)
Remote Sensor (See page E-9)
Remote Sensor
(See page E-9)
Ventilation (inlet) / Filter Cover
Built-in Security Slot (
Main Power Switch
When you plug the supplied power cable into
an active wall outlet and turn on the Main
Power switch, the POWER indicator turns
orange and the projector is in standby mode.
(See page E-15)
)*
AC Input
Connect the supplied power cable's twopin plug here, and plug the other end into
an active wall outlet. (See page E-14)
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
E-6
12. ENTER Button
Executes your menu selection and activates items selected from the
menu.
Top Features
5
6 78
10
234
11
13. CANCEL Button
Pressing this button will return to the previous menu.
While you are in the main menu, pressing this button will close the
menu.
9
1
12
13
1. POWER Button (ON / STAND BY)( )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
To turn on the projector, press and hold this button for a minimum of
two seconds. To turn off the projector, press this button twice.
2. POWER Indicator
When this indicator is green, the projector is on; when this indicator
is orange, it is in standby mode. See the Power Indicator section on
page E-27 for more details.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred,
the lamp cover is not attached properly or the projector has overheated. If this light remains orange, it indicates that you have pressed
a cabinet key while the Control Panel Key Lock is enabled. See the
Status Indicator section on page E-27 for more details.
4. LAMP Indicator
If this light blinks red rapidly, it's warning you that the lamp has reached
the end of its usable life. After this light appears, replace the lamp as
soon as possible (See page E-25). See the Lamp Indicator section
on page E-27 for more details.
5. VIDEO Button
Press this button to select a video source from a VCR, DVD player,
laser disc player or document camera.
6. S-VIDEO Button
Press this button to select an S-Video source from a VCR, DVD player,
laser disc player or document camera.
7. RGB Button
Press this button to select an RGB source from computer or component equipment connected to your RGB port.
8. AUTO ADJ. Button
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture (See page E-17).
9. Source Indicators
When one of the RGB, VIDEO or S-VIDEO input is selected, the
corresponding source indicator lights.
10. MENU Button
Displays the menu.
11. SELECT GHFE / Volume Buttons
GH : Use these buttons to select the menu of the item you wish to
adjust.
FE : Use these buttons to change the level of a selected menu item.
A press of the E button executes the selection. When no menus
appear, these buttons work as a volume control.
E-7
Terminal Panel Features
2
Part Names of the Remote Control
1
1
5
2
4
4
3
5
6
7
8
9
3
1. RGB IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player. This connector also
supports SCART output signal. See page E-12 for more details.
2. RGB AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer or
DVD player when connected to the RGB input. A commercially available audio cable is required.
3. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external source
like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.
S-VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound
from an S-Video source.
4. VIDEO IN Connector (RCA)
Connect a VCR, DVD player, laser disc player, or document camera
here to project video.
VIDEO AUDIO Input Jacks R/L (RCA)
These are your left and right channel audio inputs for stereo sound
from a Video source.
5. PC CONTROL Port (DIN 8 Pin)
Use this port to connect your PC to control your projector. This enables you to use your PC and serial communication protocol to control the projector. If you are writing your own program, typical PC
control codes are on page E-32.
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
2. MENU Button
Displays the menu for various settings and adjustments.
3. SELECT GHFE / Volume Buttons
GH : Use these buttons to select the menu of the item you wish
to adjust.
FE : Use these buttons to change the level of a selected menu
item. A press of the E button executes the selection. When
no menus appear, these buttons work as a volume control.
4. ENTER Button
Executes your menu selection and activates items selected from the
menu.
5. CANCEL Button
Pressing this button will return to the previous menu.
While you are in the main menu, pressing this button will close the
menu.
6. POWER Button (ON/STAND BY) ( )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
To turn on the projector, press and hold this button for a minimum of
two seconds. To turn off the projector, press this button twice.
7. SOURCE Button
Press this button to select a video source such as a PC, VCR or DVD
player. Each time this button is pressed, the input source will change
as follows:
RGB → Video → S-Video → RGB → ...
8. ASPECT Button
Press this button to display the Aspect Ratio select screen. See page
E-22.
9. MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
E-8
Battery Installation
Remote Control Precautions
1. Push the catch to the right and remove the battery holder.
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
32
20
LT
R
• If you will not be using the remote control for a long time, remove the
battery.
O
C
ELL
S JAPAN H
Catch
3V
• Do not place the battery upside down.
Battery holder
LT
S JAPAN H
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer.
Dispose of used batteries according to your local regulations.
O
R
20
32
• Keep the coin cell battery out of reach of children so as not to allow
them to swallow the cell battery.
C
V
L iC E L L 3
Operating Range for Wireless Remote Control
S JAPAN H
30˚
30˚
LT
20
7m/22 feet
O
R
7m/22 feet
2- L iC E L L 3 V
C
M nO
32
2. Remove the old Lithium coin cell and install new one (CR2032).
Ensure that the side with the mark “+” is up.
30˚
30˚
Remote sensor on
projector cabinet
3. Push the battery holder back into the remote control until you feel a
click.
Remote control
• The infrared signal operates by line-of-sight up to a distance of about
22 feet/7 m and within a 60-degree angle of the remote sensor on the
projector cabinet.
S JAPAN H
LT
R
O
2- L iC E L L 3 V
C
M nO
20
32
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor.
Weak battery will also prevent the remote control from properly operating the projector.
E-9
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use.
But before you get started, you must first:
1
1 Set up a screen and the projector.
2 Connect your computer or video equipment to the projector. See page
E-12 – 14.
3 Connect the supplied power cable. See
page E-14.
2
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
To the wall outlet.
3
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 21" (0.53 m)
measured diagonally when the projector is roughly 27.6 inches (0.7 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when
the projector is about 393.7 inches (10 m) from the wall or screen. Use the drawing below as a guide.
D
is
ta
nc
e
(U
E-10
9"
7.
6"
8.
39
.1
/
10
1/
31
26
3.
ni
t:
m
/in
ch
)
8.
6.
6.
7/
1/
2
40
8"
.2
"
Screen Size
0.7
/27
0.8 .6"
/31
1.0 .5"
/3
1. 9.4"
3/
51
.2
2. "
0/
78
.7
2. "
7/
10
6.
3"
3.
4/
13
3.
9"
4.
0/
15
7.
5"
5.
1/
20
0.
8"
Scr
609 een s
.6(W
iz
)X4 e (Un
57.2
i
(H) t: cm
487
/24
0(W /inch)
.7(W
)X1
)X3
80(
6
5.8(
H)
406
H)/1
.4(W
92(
)X3
W
)X1
04.8
44(
(H)
365
H)
/16
.8(W
300
0(W
)X2
)X1
"
74.3
20(
H)
(H)
/14
4(W
240
304
)X1
"
.8(W
08(
H)
)X2
28.6
200
(H)
"
/12
0(W
243
)X9
180
0(H
.8(W
)
"
)X1
82.9
(H)
203
/96
.2(W
(W)
X72
)X1
150
(H)
52.4
"
(H)
/
80(
162
W
.6(W
)X6
0(H
)X1
)
21.9
(H)
120
/64
121
"
(
W)X
.9(W
48(
)X9
H
1.4(
)
1
00"
H)/4
81.3
8(W
(W)
)X3
X61
6(H
.
0
)
61.0
80"
(H)
/32
(W)
(W)
X45
X24
.7(H
50.8
(
H
(W)
)
)
/24
60"
X38
(W)
.1(H
X18
)/20
(H)
42.7
(W)
X15
(W)
40"
X32
(H)
(H)/
3
17(W
25" 0"
)X13
21"
Len (H)
sc
ent
er
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
Distance Chart
B = Vertical distance between lens center and screen center
C = Throw distance
D = Vertical distance between lens center and top of screen (bottom of
screen for desktop)
α = Throw angle
Screen Width
Screen Diagonal
Screen Height
NOTE: Distances may vary +/-5%.
Screen center
(B)
(D)
Screen Bottom
Lens Center
Throw Angle (α)
Throw Distance (C)
Diagonal
inch
21
25
30
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300
Screen Size
Width
inch
17
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240
B
Height
inch
13
15
18
24
36
43
48
50
54
60
72
90
108
120
126
144
162
180
inch
5
6
7
10
15
17
19
20
22
24
29
36
44
48
51
58
65
73
C
Wide – Tele
inch
––– - 29
29 - 35
35 - 42
47 - 57
71 - 86
86 - 103
96 - 115
101 - 121
108 - 129
120 - 144
144 - 173
181 - 217
217 - 260
241 - 290
253 - 304
290 - 348
326 - 391
363 - 400
D
inch
1
1
2
2
3
4
5
5
5
6
7
9
10
12
12
14
16
17
α
Wide – Tele
degree
––– - 10.0
11.8 - 9.9
11.7 - 9.8
11.6 - 9.7
11.5 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
Diagonal
mm
533
635
762
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
WARNING
* Installing your projector on the ceiling must be done by a qualified technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector severely damaged.
Screen Size
Width
mm
427
508
610
813
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
B
Height
mm
320
381
457
610
914
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572
mm
130
150
180
250
370
440
490
520
550
610
740
920
1110
1230
1290
1470
1660
1840
C
Wide – Tele
mm
––– - 740
740 - 880
890 - 1070
1200 - 1440
1810 - 2180
2180 - 2620
2430 - 2920
2550 - 3060
2740 - 3290
3050 - 3660
3660 - 4400
4590 - 5510
5510 - 6610
6130 - 7350
6440 - 7720
7360 - 8830
8290 - 9940
9210 -11050
D
mm
30
40
40
60
90
110
120
120
130
150
180
220
270
300
310
350
400
440
α
Wide – Tele
degree
––– - 10.0
11.8 - 9.9
11.7 - 9.8
11.6 - 9.7
11.5 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.6
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.4 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
11.3 - 9.5
Reflecting the Image
Using a mirror to reflect your projector's image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
you're using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or your remote control to
correct the orientation. (See page E-22.)
• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 32˚F (0˚C) and 95˚F
(35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will
harm the screen image.
• Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the side or the front of
the projector.
E-11
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.
* If you accidentally hit the POWER (ON/STAND BY) button on the remote control, wait 60 seconds and then press the POWER (ON/STAND BY) button again to
resume.
Connecting Your PC or Macintosh Computer
AUDIO IN
RGB IN
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recommended that you use a
commercially available distribution amplifier
if connecting a signal cable longer than the
supplied one.
Audio cable (not supplied)
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)
PHONE
NOTE: For older Macintosh,
use a commercially available
pin adapter (not supplied) to
connect to your Mac's video
port.
PHONE
IBM VGA or Compatibles (Notebook type)
or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the
projector.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be caused
by a screen saver installed on the computer you've connected to the
projector.
To connect SCART output (RGB)
Before connections: An exclusive SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of your projector and a
SCART output (RGB) of your video equipment.
3. Turn on the power to the projector and your video equipment.
RGB IN
Projector
Video equipment
such as DVD player
4. Use the RGB button on the projector cabinet to select the RGB input.
5. Press the MENU button on the projector cabinet to display the menu.
6. From the menu, select [Advanced] → [Signal Select RGB] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs
and DVD players. It is also referred to as Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more information.
To RGB IN
Commercially available
SCART cable
Female
ADP-SC1
E-12
Connecting Your DVD Player
RGB IN
Optional 15-pin-to-RCA
(female)⳯3 cable (ADP-CV1)
Component video RCA⳯3 cable
(not supplied)
Audio Equipment
DVD player
AUDIO IN
L
R
AUDIO OUT
L
R
Component
Y
Cb
Cr
Audio cable (not supplied)
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
For a DVD player without component video (Y,Cb,Cr) output, use
common RCA cables (not provided) to connect a composite VIDEO
output of the DVD player to the Video Input of the projector.
1. Turn off the power to your projector and DVD player.
3. Turn on the projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a
commercially available component video cable (RCAX3) and the optional 15-pin-to-RCA (female)⳯3 cable to connect your DVD player
to the RGB IN connector on the projector.
NOTE: Refer to your DVD player's owner's manual for more information about
your DVD player's video output requirements,
E-13
Connecting Your VCR or Laser Disc Player
VIDEO IN
S-VIDEO IN
S-Video cable (not supplied)
Video cable (not supplied)
Audio equipment
VCR/ Laser disc player
AUDIO IN
AUDIO OUT
L
L
R
R
S-VIDEO OUT
Audio cable
(not supplied)
VIDEO OUT
Use common RCA cables (not provided) to connect your VCR, laser
disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or
document camera.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source
is played back in fast-forward or fast-rewind via a scan converter.
2. Connect one end of your RCA cable to the video output connector on
the back of your VCR or laser disc player, connect the other end to
the Video input on your projector. Use an audio cable (not supplied)
to connect the audio from your VCR or laser disc player to your audio
equipment (if your VCR or laser disc player has this capability). Be
careful to keep your right and left channel connections correct for
stereo sound.
3. Turn on the projector and the VCR or laser disc player.
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's two-pin plug to
the AC IN of the projector, and then connect the other
plug of the supplied power cable in the wall outlet.
E-14
PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a
picture onto the screen.
2. Press the ENTER button to execute the selection.
Turning on the Projector
NOTE:
• The projector has two power switches: main power switch and POWER (ON/
STAND BY) button.
• When plugging in or unplugging the supplied power cable, make sure that the
main power switch is pushed to the off (O) position. Failure to do so may
cause damage to the projector.
To turn on the main power to the projector, press the Main Power switch
to the on position ( I ).
After this has been done, you can proceed to the menu operation.
If you want, you can select the menu language later. See "Language"
on page E-22.
NOTE: Immediately after turning on the projector, screen flicker may occur. This
is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
Only after you press the POWER (ON/STAND BY) button on the projector cabinet or the remote control for a minimum of 2 seconds will the
power indicator turn to green and the projector become ready to use.
If one of the following things happens, the projector will not turn on.
* If the internal temperature of the projector is too high, the projector
detects abnormal high temperature. In this condition the projector
will not turn on to protect the internal system. If this happens, wait for
the projector's internal components to cool down.
* When the lamp reaches its end of usable life, the projector will not
turn on. If this happens, replace the lamp.
* If the lamp fails to light, and if the STATUS indicator flashes on and
off in a cycle of six times, wait a full minute and then turn on the
power.
Selecting a Source
Note on Startup screen (Menu Language Select screen)
Selecting the computer or video source
When you first turn on the projector, you will get the Startup screen. This
screen gives you the opportunity to select one of the 19 menu languages:
English, German, French, Italian, Spanish, Swedish, Japanese, Korean,
the Simplified Chinese, Polish, Hungarian, Russian, Greek, Turkish,
Dutch, Norwegian, Finnish, Portuguese and Czech.
To select a menu language, follow these steps:
Using the Remote Control
Press the SOURCE button.
1. Use the SELECT G or H button to select one of the 19 languages for
the menu.
Using the cabinet buttons
Press any one of the RGB,
VIDEO or S-VIDEO buttons.
NOTE: If no input signal is available, the projector will display a blue background
(factory preset).
E-15
Place your projector on a flat level surface and ensure that the projector
is square to the screen.
CAUTION
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
Lift the front edge of the projector to center the image vertically.
* If the projected image does not appear square to the screen then
use the Keystone feature for proper adjustment. See page E-21.
Zoom
Use the ZOOM lever to finely adjust the image size on the screen.
Adjusting the Picture Size and Position
Move the projector left to center the image horizontally on the screen.
You can use the ZOOM lever to enlarge or reduce an image size.
Focus
Use the FOCUS ring to obtain the best focus.
Adjust the Tilt Foot
1. Lift the front edge of the projector.
Correcting the Vertical Keystone Distortion
Adjustable Tilt Foot Lever
Adjustable Tilt Foot Lever
Adjustable Tilt Foot
2. Push up the Adjustable Tilt Foot Levers on the right and left sides of
the projector to extend the adjustable tilt feet (maximum height).
3. Push down the Adjustable Tilt Foot Levers.
Use Keystone correction for proper adjustment. See page E-21.
4. Lower the front of the projector to the desired height (max. 40mm/
1.6”) and release the Adjustable Tilt Foot Lever to lock the Adjustable tilt foot. There is approximately 10 degrees of up and down adjustment for the front of the projector.
E-16
Optimizing RGB Picture Automatically
Turning off the Image and Sound
Adjusting the Image Using Auto Adjust
Press the MUTE button on the remote control to turn off the image and
sound for a short period of time. Press again to restore the image and
sound.
Optimizing RGB image automatically
Press the AUTO ADJ. button on the projector cabinet to optimize an
RGB image automatically.
[Poor picture]
Turning off the Projector
To turn off the projector:
First, press the POWER (ON/STAND BY) button on the projector cabinet or the remote control. The “Power Off / Are you sure?” message will
appear.
[Normal picture]
Press the AUTO ADJ. button on the projector cabinet to fine-tune the
computer image or to remove any vertical banding that might appear
and to reduce video noise, dot interference or cross talk (this is evident
when part of your image appears to be shimmering). This function adjusts the clock frequencies that eliminate the horizontal banding in the
image. This function also adjusts the clock phase to reduce video noise,
dot interference or cross talk. (This is evident when part of your image
appears to be shimmering.)
This adjustment may be necessary when you connect your computer
for the first time.
Secondly, press the ENTER button or press the POWER (ON/STAND
BY) button again.
The power indicator will glow orange. After the projector turns off, the
cooling fans keep operating for 60 seconds (Cooling-off time).
Lastly, turn off the Main Power switch. The power indicator will go out.
Last unplug the power cable.
NOTE:
• Some signals may not be displayed correctly or take time.
• The Auto Adjust function does not work for component and video signal.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock
and Phase manually. See page E-24.
Turning Up or Down Volume
Sound level from the speaker on the projector can be adjusted.
NOTE: When the menu appears, you cannot adjust the volume.
decrease volume
CAUTION
Do not unplug the power cable from the wall outlet or do not turn
off the main power under any one of the following circumstances.
Doing so can cause damage to the projector:
• While the Hour Glass icon appears.
• While the cooling fans are running. (The cooling fans continue
to work for 60 seconds after the projector is turned off).
increase volume
E-17
USING ON-SCREEN MENU
6. Repeat steps 2-5 to adjust an additional item, or press the MENU
button to close the menu.
Basic Menu Operation
Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or projector cabinet to
display the Menu.
2. Press the SELECT GH buttons on the remote control or the projector cabinet to highlight the menu for the item you want to adjust or
set.
3. Press the SELECT E button or the ENTER button on the remote
control or the projector cabinet to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using SELECT
F or E buttons on the remote control or the projector cabinet.
The on-screen slide bar will show you the amount of increase or
decrease.
5. Changes are stored until you adjust it again.
CANCEL ........ Return to the previous screen.
E-18
List of Menu Items
Picture
Brightness
Contrast
Sharpness
Color
Hue
Picture Management
Image
Keystone
Keystone Save
Aspect Ratio
Cinema Position
Setup
Language
Menu Color Select
Menu Display Time
Background
Orientation
Advanced
Security
Control Panel Key Lock
High Speed Fan Mode
Signal Select RGB
Video
S-Video
Page2
Information
Page1
Page2
Page3
Default
Factory Default
Presentation, Video, Movie, Graphic, sRGB
User
Base Setting
Presentation, Video, Movie, Graphic, sRGB
White Balance
Brightness R,G,B Contrast R,G,B
Gamma Correction Dynamic, Black Detail, Natural
On, Off
Normal, Wide Zoom, Cinema, Native
Language-1 English, Deutsch, Français, Italiano, Español, Português, Nederlands
Language-2 Svenska, Norsk, Suomi, Česky, Magyar, Polski, Türkçe
Language-3
,
,
,
,
Color, Monochrome
Manual, Auto 5 sec, Auto 15sec, Auto 45 sec
Blue, Black, Logo
Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front
On, Off
Enable, Disable
On, Off
RGB/Component, RGB, Component, Scart
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Power Management
On, Off
Noise reduction
Off, Low, High
Auto Adjust
On, Off
Vertical
Horizontal
Clock
Phase
Communication Speed 4800, 9600, 19200
Source Index, Horizontal Frequency, Vertical Frequency, Sync Polarity
Signal Type, Video Type, Sync Type, Interlace
Remaining Lamp Time, Lamp Hour Meter, Filter Usage, Projector Usage
Current Signal
All Data
Clear Filter Usage
Clear Lamp Hour Meter
NOTE: Some menu items are not available depending on the input source.
E-19
Menu Elements
Title
Slide bar
Radio button
Source
Highlight
Check mark
Tab
Key symbol
Menu windows or dialog boxes typically have the following elements:
Title .................... Indicates the menu title.
Highlight ............. Indicates the selected menu or item.
Source ................ Indicates the currently selected source.
Solid triangle ...... Indicates further choices are available. A highlighted
triangle indicates the item is active.
Tab ..................... Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button ....... Use this round button to select an option in a dialog
box.
Check mark ........ Indicates the item is selected.
Slide bar ............. Indicates settings or the direction of adjustment.
Key symbol ........ Indicates the Control Panel Key Lock is enabled.
E-20
Solid triangle
User Adjust (when using User )
When selecting user adjustable presetting (User), the submenu will
be displayed.
You can customize each gamma or color. To do so, first select “User”
and press the ENTER button, and then proceed the following steps.
Menu Descriptions & Functions
Picture
Selecting Base Setting <Base Setting>
This feature allows you to use white balance or gamma values as
reference data to optimize for various types of images. You can select one of the following five settings.
• Presentation
• Video
• Movie
• Graphic
• sRGB
Adjusting Brightness, Contrast, Sharpness, Color, Hue and Picture
Management.
Brightness ...... Adjusts the brightness level or the back raster intensity.
Contrast ......... Adjusts the intensity of the image according to the
incoming signal.
Adjusting White Balance <White Balance>
This allows you to adjust the white balance. Brightness for each color
(RGB) is used to adjust the black level of the screen; Contrast for
each color (RGB) to adjust the white level of the screen.
Selecting Gamma Correction Mode <Gamma Correction>
Each mode is recommended for :
Dynamic ......... For true color reproduction of natural tones
Sharpness ..... Controls the detail of the image for Video.
Black Detail .... For dark portions of a picture
Color .............. Increases or decreases the color saturation level (not
valid for RGB).
Natural ........... Normal settings
Hue ................ Varies the color level from +/- green to +/-blue. The
red level is used as reference. This adjustment is only
valid for Video and Component inputs (not valid for
RGB).
Image
Picture Management
This option allows you to adjust neutral tint for yellow, cyan or magenta.
There are 5 factory presets optimized for various types of images, or
you can set user adjustable settings.
Correcting Vertical Keystone Distortion [Keystone]
This feature corrects the keystone (trapezoidal) distortion to make
the top of the screen longer or shorter to be the same as the bottom.
Use the F or E buttons on the slide bar to correct the keystone (trapezoidal) distortion.
Presentation .. Recommended for making a presentation using a
PowerPoint file
Video ............. Recommended for regular picture such as TV program
Movie ............. Recommended for movie
NOTE: The keystone angle can be corrected between 30 degrees upward and 30
degrees downward at a 0 degree-projection angle. Depending on the type of
graphics being used, the picture may get blurred or keystone correction may not
be possible when excessive keystone correction is used. The idea is, the closer
you are to native resolution, the better image you will see.
Graphic .......... Recommended for graphics
sRGB ............. Standard color values
User ............... User adjustable
NOTE: When “sRGB”, “Graphic”, “Video” or “Movie” is selected, the brightness decreases slightly when compared to “Presentation”. This is not a malfunction.
Saving Vertical Keystone Correction [Keystone Save]
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved
when the projector is off.
E-21
Selecting Aspect Ratio [ Aspect Ratio]
Aspect Ratio allows you to select the best Aspect mode to display
your source image. You can also display the Aspect Ratio window by
pressing the “ASPECT” button on the remote control. (See page E-8).
When 4:3 is selected from the source (i.e. DVD player), the following
selections will display:
Normal
Wide Zoom
Cinema
Standard
4:3 Aspect
Left and right
stretched
Left and right
stretched
Native
Selecting Menu Color [Menu Color Select]
You can choose between two color modes for menu color: color and
monochrome.
When 16:9 is selected from the source (i.e. DVD player), the following selections will display:
Normal
16:9 image
displayed in
4:3 mode
Wide Zoom
Left and right
stretched
Cinema
Selecting Menu Language [Language]
You can choose one of 19 languages for on-screen instructions.
The options are: English, German, French, Italian, Spanish, Swedish, Japanese, Korean, the Simplified Chinese, Polish, Hungarian,
Russian, Greek, Turkish, Dutch, Norwegian, Finnish, Portuguese and
Czech.
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the
last touch of a button to turn off the menu.
The preset choices are “Manual”, “Auto 5 sec”, “Auto 15 sec”, and
“Auto 45 sec”. The “Auto 45 sec” is the factory preset.
Selecting a Color or Logo for Background [Background]
Use this feature to display a black/ blue screen or logo when no signal is available.
Native
Selecting Projector Orientation [Orientation]
This sets your image for your type of projection. The options are:
desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.
Left and right
stretched to
display the true
aspect
Native (RGB only): Turns off the Advanced AccuBlend feature. The
projector displays the current image in its true resolution.
NOTE: Selecting “Ceiling front” or “Ceiling rear” will turn on the Auto Adjust
feature to optimize an RGB image automatically. (See page E-24)
Advanced
NOTE:
* While you are displaying an image with higher resolution than the projector’s
native resolution, “Native” is not available.
* You can adjust image positions for Cinema. See “Cinema Position” for setting image positions.
Copyright
Please note that using this projector for the purpose of commercial gain or
the attraction of public attention in a venue such as a coffee shop or hotel and
employing compression or expansion of the screen image with a "Aspect
Ratio" setting may raise concern about the infringement of copyrights which
are protected by copyright law.
Adjusting the Vertical Position of Image [Cinema Position] (for Cinema only)
This feature adjusts the vertical position of the image when viewing
video with an aspect ratio selected.
When “Cinema” is selected in “Aspect Ratio”, the image is displayed
with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
Security
A keyword can be set for your projector to avoid operation by an unauthorized user using the Menu. When a keyword is set, turning on the
projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image.
To enable the Security function:
1. Select [Advanced] → [Security] and press the F button to select “On”.
NOTE: This option is available only when “Cinema” is selected in Aspect Ratio.
Setup
The [Keyword] screen will be displayed.
E-22
2. Type in a combination of the four SELECT buttons ( GHFE ) and
press the ENTER button.
NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request code. Your request
code is displayed in the Keyword Confirmation screen. In this example “K99245L8-JNGJ-4XU9-1YAT-EEA2” is a request code.
NOTE: A keyword must be four to 10 digits in length.
Disabling the Cabinet Buttons [Control Panel Key Lock]
This option turns on or off the Control Panel Key Lock function.
NOTE:
* This Control Panel Key Lock does not affect the remote control and the PC
Control functions.
* When the cabinet buttons are disabled, pressing and holding the CANCEL
button for about 10 seconds will change the setting to enable.
* Key symbol indicates the Control Panel Key Lock is enabled.
The [Confirm Keyword] screen will be displayed.
Enabling High Speed Fan Mode [High Speed Fan Mode]
This option allows you to select two modes for fan speed: high-speed
mode and normal speed mode.
When you wish to cool down the temperature inside the projector
quickly, select “On”.
3. Type in the same combination of SELECT buttons ( GHFE ) and
press the ENTER button.
The confirmation screen will be displayed.
NOTE: Enable High Speed Fan mode if you continue to use the projector for
consecutive days.
Selecting Signal Format [Signal Select]
<RGB>
Allows you to choose “RGB” for an RGB source such as a computer,
or “Component” for a component video source such as a DVD player.
Normally select “RGB/Component” and the projector automatically
detects a component signal. However there may be some component signals that the projector is unable to detect. If this is the case,
select “Component”. Select “Scart” for the European Scart.
4. Select “Yes” and press the ENTER button.
The Security function has been enabled.
<Video & S-Video System Select>
This feature enables you to select composite video standards manually. Normally select “Auto”.
When you select the video standard for Video and S-Video, select
the video standard from the pull-down menu.
This must be done for Video and S-Video respectively.
To disable the Security function:
1. Select [Advanced] → [Security] and press the E button to select “Off”.
Page2
The Keyword confirmation screen will be displayed.
Enabling Power Management [Power Management]
When this option is on and there is no input for five minutes or more,
the projector will automatically turn itself off.
2. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the Security function will be
disabled.
Selecting Noise Reduction Level [Noise Reduction]
Select one of the three levels for reducing video noise: Off, Low, or
High.
When the Security function is enabled and the projector is turned
on, the projector will display a blue background.
To display an image at this time, press the MENU button to display the
Keyword input screen.
Type in the correct keyword. The projector will display an image.
E-23
NOTE: The lower the Noise Reduction level, the better the image quality by
way of higher video bandwidth.
Enabling Auto Adjust [Auto Adjust]
When “Auto Adjust” is set to “On”, the projector automatically determines the best resolution for the current RGB input signal to project
an image using NEC’s Advanced AccuBlend Intelligent Pixel Blending Technology.
The image can be automatically adjusted for position and stability;
“Horizontal Position”, “Vertical Position”, “Clock” and “Phase”.
On .................. Automatically adjusts image “Horizontal Position”,
“Vertical Position”, “Clock” and “Phase”.
Off .................. User can adjust the image display functions (“Horizontal Position”, “Vertical Position”, “Clock” and
“Phase”) manually.
[Page 1]
Source Index
Horizontal Frequency
Vertical Frequency
Sync Polarity
[Page 2]
Signal Type
Video Type
Sync Type
Interlace
NOTE: Selecting “Ceiling front” or “Ceiling rear” for “Orientation” will automatically turn on this feature.
Adjusting Position/Clock (when Auto Adjust is off)
This allows you to manually adjust the image horizontally and vertically, and adjust Clock and Phase.
[Page 3]
Remaining Lamp Time (%)*
Lamp Hour Meter (H)
Filter Usage
Projector Usage
* The progress indicator shows the percentage of remaining bulb life. The value informs you of the amount of lamp usage.
When the remaining lamp time reaches 0,
the Remaining Lamp Time bar indicator
changes from 0% to 100 Hours and starts
counting down.
If the remaining lamp time reaches 0 hours,
the projector will not turn on.
Default
<Horizontal/Vertical>
Adjusts the image location horizontally and vertically.
This adjustment is made automatically when the Auto Adjust is turned
on.
<Clock>
Use this item with the “Auto Adjust off” to fine tune the computer
image or to remove any vertical banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be necessary when you connect your computer for the first time. This adjustment is made automatically when the Auto Adjust is turned on.
<Phase>
Use this item to adjust the clock phase or to reduce video noise, dot
interference or cross talk. (This is evident when part of your image
appears to be shimmering.)
Use “Phase” only after the “Clock” is complete.
This adjustment is made automatically when the Auto Adjust is turned
on.
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (DIN 8 Pin). It
supports data rates from 4800 to 19200 bps.
The default is 19200 bps.
Select the appropriate baud rate for your equipment to be connected
(depending on the equipment, a lower baud rate may be recommended
for long cable runs).
Returning to Factory Default [Factory Default]
The Factory Default feature allows you to change adjustments and setting to the factory preset for source except the following:
<Current Signal>
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: Brightness, Contrast, Color, Hue, Sharpness, Aspect Ratio, Horizontal Position, Vertical Position, Clock, Phase
and Picture Management.
<All Data>
Reset all the adjustments and settings for all the signals to the factory
preset.
The items can be reset except Language, Lamp Remaining Time, Lamp
Hour Meter and Filter Usage. To reset the lamp usage time, see “Clear
Lamp Hour Meter” and “Clear Filter Usage”.
Resetting the Filter Usage Hours [Clear Filter Usage]
Resets the filter usage back to zero. Selecting this option displays
submenu for a confirmation.
Information
Clearing Lamp Hour Meter [Clear Lamp Hour Meter]
Resets the lamp clock back to zero. Selecting this option displays
submenu for a confirmation.
NOTE: The projector will turn off and go into standby mode after 3100 hours of
service. If this happens, press and hold the ON/STAND BY and CANCEL buttons
on the remote control simultaneously for a minimum of 10 seconds to reset the
lamp clock back to zero. Do this only after replacing the lamp.
Displays the status of the current signal and lamp usage. This item has
three pages. The information included is as follows:
E-24
MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp and clean the filter.
3. Insert a new lamp housing until the lamp housing is plugged into the
socket.
Replacing the Lamp
CAUTION
Do not use a lamp other than the NEC replacement lamp (VT60LP).
Order this from your NEC dealer.
After your lamp has been operating for 3000 hours or longer, the LAMP
indicator in the cabinet will blink red and the message will appear. Even
though the lamp may still be working, replace it at 3000 hours to maintain optimal projector performance.
Secure it in place with the two screws.
Be sure to tighten the screws.
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been used.
It will be extremely hot. Turn the projector off, wait 60 seconds,
turn off the main power switch and then disconnect the power
cable. Allow at least one hour for the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except the lamp cover screw
and two lamp case screws. You could receive an electric shock.
• The projector will turn off and go into stand by mode after 3100
hours of service. If this happens, be sure to replace the lamp. If
you continue to use the lamp after 3000 hours of use, the lamp
bulb may shatter, and pieces of glass may be scattered in the
lamp case. Do not touch them as the pieces of glass may cause
injury. If this happens, contact your NEC dealer for lamp replacement.
4. Reattach the lamp cover.
Tighten the lamp cover screw.
Be sure to tighten the screw.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a freewheeling condition and remove the lamp cover. The lamp cover screw
is not removable.
Catch
5. After you install a new lamp, select the menu → [Default] → [Clear
Lamp Hour Meter] to reset the lamp usage hours.
2. Loosen the two screws securing the lamp housing until the screwdriver goes into a freewheeling condition. The two screws are not
removable.
Remove the lamp housing by holding it.
NOTE: There is an interlock on this case to prevent the risk of electrical shock.
Do not attempt to circumvent this interlock.
Catch
Interlock
E-25
NOTE: When the lamp exceeds 3100 hours of service, the projector cannot
turn on and the menu is not displayed. If this happens, press and hold the
ON/STAND BY and CANCEL buttons on the remote control simultaneously
for a minimum of 10 seconds while in standby mode. When the lamp time
clock is reset to zero, the LAMP indicator goes out.
3. Reinstall the new filter cover.
Cleaning
Cleaning or Replacing the Filter
The air-filter sponge keeps the inside of the projector from dust or dirt
and should be cleaned after every 100 hours of operation (more often in
dusty conditions). If the filter is dirty or clogged, your projector may overheat.
CAUTION
• Turn off the projector, turn off the main power switch and unplug the projector before replacing the filter.
• Only clean the outside of the filter cover with a vacuum cleaner.
• Do not attempt to operate the projector without the filter cover.
NOTE: Do not wash the filter with soap and water. Soap and water will damage
the filter membrane. Before replacing the filter, remove dust and dirt from the
projector cabinet. Keep out dust and dirt during filter replacement.
To clean the air-filter:
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter
comes in the same package with your replacement lamp.
Vacuum the filter-through the filter cover.
Cleaning the Cabinet and the Lens
To reset the filter usage time, from the menu, select [Default] → [Clear
Filter Usage].
See also page E-24 for resetting the filter usage time.
To replace the filter (sponge):
1. Remove the filter cover by pushing up on the catch of the cover until
you feel it detach.
Catch
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
2. Gently peel off the filter (sponge) and replace it with the new one.
E-26
TROUBLESHOOTING
This section helps you resolve problems you may encounter while setting up or using the projector.
Power Indicator
Indicator Condition
Projector Condition
Off
Blinking light
Green
0.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
Orange
Steady light
Green
Orange
Note
–
The main power is off.
The projector is getting ready Wait for a moment.
to turn on.
The projector is cooling down. Wait for a moment.
The projector is turned on.
The projector is in Standby.
–
–
Status Indicator
Indicator Condition
Off
Blinking light
Red
4 cycle (0.5 sec On, Fan error
0.5 sec Off)
6 cycle (0.5 sec On, Lamp error
0.5 sec Off)
Re-firing the lamp
Green
Steady light
Projector Condition
Orange
Note
Normal
–
1 cycle (0.5 sec On, Lamp cover error or lamp Replace the lamp cover or
2.5 sec Off)
housing error
lamp housing correctly.
2 cycle (0.5 sec On, Temperature error
The projector is overheated.
0.5 sec Off)
Move the projector to a cooler
location.
Control Panel key locked
Fans will not work correctly.
Lamp fails to light. Wait a full
minute and then turn on again.
The projector is re-firing.
You have pressed control
panel key when Control Panel
Key Lock is enabled.
Lamp Indicator
Indicator Condition
Off
Blinking light
Red
Steady light
Red
Projector Condition
Note
–
Normal
Lamp has reached its end of Replace the lamp.
life. Lamp replacement message will be displayed.
Lamp has been used beyond Replace the lamp.
its limit. The projector will not
turn on until the lamp is replaced.
E-27
Common Problems & Solutions
Problem
Check These Items
Does not turn on
• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages E-14 and 15.
• Ensure that the lamp cover or lamp housing is installed correctly. See page E-25.
• Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is
insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move
the projector to a cooler location.
No picture
• Use the RGB, VIDEO or S-VIDEO button on the cabinet or the SOURCE button on the remote control to select
your source (RGB, Video or S-Video). See page E-15.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page E-21.
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using “Factory Default” in the menu. See page E-24.
Image isn’t square to the
screen
• Reposition the projector to improve its angle to the screen. See page E-16.
• Use the Keystone correction function to correct the trapezoid distortion. See page E-21.
Picture is blurred
• Adjust the focus. See page E-16.
• Reposition the projector to improve its angle to the screen. See page E-16.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See
pages E-10 and 11.
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Image is scrolling vertically, horizontally or
both
• Use the RGB, VIDEO or S-VIDEO button on the cabinet or the SOURCE button on the remote control to select
your source (RGB, Video or S-Video). See page E-15.
Remote control does
not work
• Install new battery. See page E-9.
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. See page E-9.
Indicator is lit or blinking
• See the Power/Status/Lamp Indicator on page E-27.
Cross color in RGB
mode
• If Auto Adjust is off, turn it on or adjust the image manually with Horizontal / Vertical / Clock / Phase in the
Advanced menu. See page E-24.
E-28
SPECIFICATIONS
This section provides technical information about the VT46 Projector's performance.
Model Number
Optical
LCD Panel
Resolution
Lens
Lamp
Image Size
Projection Distance
Projection Angle
Keystone Correction
Electrical
Inputs
Video Compatibility
Scan Rate
Video Bandwidth
Color Reproduction
Horizontal Resolution
External Control
Sync Compatibility
Built-in Speaker
Power Requirement
Input Current
Power Consumption
Mechanical
Installation Orientation
Dimensions
Net Weight
Environmental Considerations
Regulations
VT46
0.7" p-Si TFT active-matrix
800⳯600 pixels* native, up to UXGA with Advanced AccuBlend
Manual zoom and focus:
F1.7 - 2.0 f=21.6 - 25.9mm
160 W
21 - 300 inches (0.5 - 7.6 m) diagonal
2.38 - 35.8 ft / 7.3 (Tele) - 10.9 m (Tele)
Tele : 9.5° - 10.0° Wide : 11.3° - 11.8°
+/- 30 degrees electronic
1 RGB/Component (D-Sub 15 Pin), 1 S-Video (DIN 4 Pin), 1 Video (RCA),
1 Stereo Mini Audio, 2 (L/R) RCA Audio, 1 PC Control (DIN 8 Pin)
NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM, HDTV: 1080i, 1080i/50Hz, 720p, 576p, 480p, 480i/
60Hz
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over) / Vertical: 50 Hz to 120 Hz
RGB: 80 MHz (-3dB)
16.7 million colors simultaneously, Full color
NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 550 TV lines
SECAM: 350 TV lines
YCbCr: 800 TV lines
RGB: 800 dots (H)⳯600 dots (V)
RS232, IR
Separate Sync / Composite Sync / Sync on G
1W (monaural)
100 - 120V AC / 200 - 240V AC, 50 / 60 Hz
2.3A (100 - 120V AC) / 1.1A (200 - 240V AC)
220W (7.5W in Standby mode)
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
12.2" (W)⳯3.5" (H)⳯9.1" (D)
310mm (W)⳯89mm (H)⳯230mm (D)
(not including protrusions)
6.5 lbs / 2.9 kg
Operational Temperatures : 32° to 95°F (0° to 35°C), 20% to 80% humidity (non-condensing)
Storage Temperatures : 14° to 122°F (-10° to 50°C), 20% to 80% humidity (non-condensing)
UL Approved (UL 60950, CSA 60950)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS3548 Class B
Meets EMC Directive (EN55022:1998, EN55024-1998, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
For additional information visit:
US : http://www.necvisualsystems.com
Europe : http://www.nec-europe.com/
Global : http://www.nec-pj.com/
* Effective pixels are more than 99.99%.
The specifications are subject to change without notice.
E-29
APPENDIX
Cabinet Dimensions
230 (9.1")
245 (9.6")
89 (3.5")
310 (12.2")
Lens center
96 (3.8")
41.7
(1.6")
99.2 (3.9")
73.5 (2.9")
Lens center
Unit = mm (inch)
Pin Assignments of D-Sub RGB Input Connector
Mini D-Sub 15 Pin Connector
5
4 3 2 1
10 9 8 7 6
15 14 13 12 11
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
RGB Signal (Analog)
YCbCr Signal
Red
Green or Sync on Green
Blue
Ground
Ground
Red Ground
Green Ground
Blue Ground
No Connection
Sync Signal Ground
SCART Sync
Bi-directional DATA (SDA)
Horizontal Sync or Composite Sync
Vertical Sync
Data Clock
Cr
Y
Cb
E-30
Cr Ground
Y Ground
Cb Ground
Sync
Compatible Input Signal List
Signal
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
NTSC
PAL
PAL60
SECAM
VESA
IBM
MAC
MAC
MAC
VESA
VESA
IBM
VESA
IBM
VESA
IBM
IBM
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
SUN
SGI
VESA
VESA
MAC
HP
SUN
VESA
VESA
SXGA+
HDTV (1080p)
SDTV(576i)(625i)
SDTV(576p)(625p)
HDTV (1080i)(1125i)
HDTV (1080i)(1125i)
HDTV (720p)(750p)
SDTV (480p)(525p)
VESA
VESA
VESA
VESA
DVD YCbCr
DVD YCbCr
Resolution
( Dots )
–
–
–
–
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
720 ⳯ 350
720 ⳯ 400
720 ⳯ 350
720 ⳯ 400
800 ⳯ 600
800 ⳯ 600
800 ⳯ 600
800 ⳯ 600
800 ⳯ 600
832 ⳯ 624
1024 ⳯ 768
1024 ⳯ 768
1024 ⳯ 768
1024 ⳯ 768
1024 ⳯ 768
1024 ⳯ 768
1152 ⳯ 864
1152 ⳯ 870
1152 ⳯ 900
1152 ⳯ 900
1280 ⳯ 960
1280 ⳯ 1024
1280 ⳯ 1024
1280 ⳯ 1024
1280 ⳯ 1024
1280 ⳯ 1024
1280 ⳯ 1024
1400 ⳯ 1050
1920 ⳯ 1080
–
–
1920 ⳯ 1080
1920 ⳯ 1080
1280 ⳯ 720
–
1600 ⳯ 1200
1600 ⳯ 1200
1600 ⳯ 1200
1600 ⳯ 1200
–
–
Frequency H.
( kHz )
15.734
15.625
15.734
15.625
31.47
31.47
31.47
34.97
35
37.86
37.5
39.375
43.269
31.469
37.927
39.44
39.44
35.16
37.879
48.077
46.88
53.674
49.725
35.5
48.363
56.476
60.241
60.023
68.677
67.5
68.681
61.796
71.736
60
63.981
69.89
78.125
81.13
79.976
91.146
–
67.5
15.6
31.5
33.75
28.125
45
31.47
75.0
81.25
87.5
93.75
15.734
15.625
Refresh Rate
( Hz )
60
50
60
50
59.94
60
60
66.67
66.67
72.81
75
75
85.01
70.09
85.04
87.85
87.85
56.25
60.32
72.19
75
85.06
74.55
43 Interlaced
60
70.07
74.93
75.03
85
75
75.06
65.95
76.05
60
60.02
65.18
72.01
76.11
75.03
85.02
–
60 Progressive
50
50
60 Interlace
50 Interlace
60 Progressive
59.94 Progressive
60
65
70
75
59.94 Interlaced
50 Interlaced
# : Images in above flagged with # are compressed with Advanced AccuBlend.
NOTE: Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change
the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600⳯1200) is supported for separate sync signal only.
E-31
PC Control Codes
Cable Connection
Communication Protocol
Baud rate:
19200 bps
Function
Code Data
Data length:
8 bits
POWER ON
02H 00H 00H 00H 00H 02H
Parity:
No parity
POWER OFF
02H 01H 00H 00H 00H 03H
Stop bit:
One bit
X on/off:
None
Communications
procedure:
Full duplex
INPUT SELECT RGB
02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT VIDEO
02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO
02H 03H 00H 00H 02H 01H 0BH 13H
PICTURE MUTE ON
02H 10H 00H 00H 00H 12H
PICTURE MUTE OFF
02H 11H 00H 00H 00H 13H
SOUND MUTE ON
02H 12H 00H 00H 00H 14H
SOUND MUTE OFF
02H 13H 00H 00H 00H 15H
PC Control Connector (DIN-8P)
To RxD of PC
8
5
4
2
To GND of PC
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
6
7
3
1
To TxD of PC
NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector.
E-32
TravelCare Guide
6) Problems or damage caused by expendable supplies or devices
connected to the product other than those designated by NEC.
TravelCare - a service for international travelers
7) Problems caused by natural consumption, wear or deterioration
of parts under normal usage conditions.
This product is eligible for "TravelCare", NEC's unique international warranty.
Please note that TravelCare coverage differs in part from coverage under the warranty included with the product.
8) Problems or damage to lamps and other expendable supplies,
included parts or optional parts.
9) Other conditions stipulated in the warranty included with the product also apply.
Services offered with TravelCare
This warranty allows customers to receive service on their product at
the NEC and NEC-designated service stations in the countries listed
herein when temporarily traveling internationally for business or pleasure.
For details on services offered by the different service stations, please
refer to the "List of TravelCare Outlets" below.
1 Repair services
The product will be repaired and delivered within 10 business days,
not including shipping time.
During the term of warranty, the cost of maintenance parts, labor
costs for repairs and shipping costs within the service station's coverage area are covered by the warranty.
2 Replacement product rental service
If the customer desires, he or she can rent a replacement product
while the original product is being repaired.
Fee: US$200 for 12 days
This fee must be paid at the local service station in cash or credit
card.
The $200 rental fee is non-refundable even if the customer rents it
less than 12 days before returning.
The replacement product will be delivered within 3 business days.
If the customer did not return the replacement product within 12 days,
the customer will be charged the price of the unit.
If the customer returned the replacement product in a faulty or damaged condition, the repair cost will be charged to the customer.
Note that this service is not offered in all countries and regions. Please
refer to the "List of TravelCare Outlets".
In addition, this replacement product rental service is not offered after the product's warranty has expired.
Term of warranty
NOTE: The product can be used overseas with voltages of 100 to 120V and 200
to 240V by using a power cable suited for the standards and power source voltage of the country in which the product is being used.
List of TravelCare Outlets
This list applies as of June 1, 2002.
For the most up-to-date information, please refer to the websites of the
service stations in the various countries on the List of TravelCare Outlets or to the NEC website at http://www.nec-pj.com.
In Europe
NEC Europe, Ltd. / European Technical Centre
Address:
Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.
Telephone:
+44 1952 237000
Fax Line:
+44 1952 237006
Email Address:
[email protected]
WEB Address:
http://www.neceur.com
(Regions Covered)
EU:
Austria*, Belgium*, Denmark*, Finland*, France*, Germany*,
Greece*, Ireland*, Italy*, Luxembourg*, The Netherlands*,
Portugal*, Spain*, Sweden* and the United Kingdom*
EEA:
Norway*, Iceland and Liechtenstein
In North America
NEC Solutions (America), Inc.
Address:
1250 Arlington Heights Road, Itasca,
Illinois 60143, U.S.A.
Telephone:
+1 800 836 0655
Fax Line:
+1 800 356 2415
Email Address:
[email protected]
WEB Address:
http://www.necvisualsystems.com
(Regions Covered)
U.S.A. *, Canada*
1
a. Upon presentation of the warranty or receipt received upon purchase:
Valid for the term indicated on the warranty or the normal term of
warranty for the country of purchase.
b. When only the product is brought in:
Valid for a period of within 14 months of the date of manufacture
indicated by the serial number attached to the product.
2 When a product whose term of warranty is expired is brought in:
Repairs will be offered for a fee. In this case the customer is not
eligible for the replacement product rental service.
3 In the following cases, repairs may be charged, even if the product's
warranty is still in effect:
1) If the term of warranty, model name, serial number and name of
the store of purchase are not indicated on the warranty or have
been altered.
2) Problems or damage caused by dropping or shocks during shipment or movement by the customer or by improper handling by
the customers.
In Oceania
NEC Australia Pty., Ltd.
Address: New South Wales;
184 Milperra Road, Reversby 2212
Victoria;
480 Princess Hwy Noble Park 3174
South Australia;
84A Richmond Road, Keswick 5035
Queensland;
116 Ipswich Road, Woollongabba 4102
Western Australia;
45 Sarich Court Osborne Park 6017
Telephone:
131 632 (from domestic)
+61 8 8375 5706 (from overseas)
Fax Line:
+61 8 8375 5757
Email Address:
[email protected]
WEB Address:
http://www.nec.com.au
3) Problems or damage caused by improper usage or unwarrantable alterations or repairs by the customer.
4) Problems or damage caused by fire, salt damage, gas damage,
earthquakes, lightning damage, storm or flood damage or other
natural disasters or such external factors as dust, cigarette
smoke, abnormal voltage, etc.
5) Problems or damage caused by use in hot or humid places, in
vehicles, boats or ships, etc.
E-33
(Regions Covered)
Australia*, New Zealand
ABBA Electronics L.L.C.
Address:
Tariq Bin Ziyad Road, P.O.Box 327, Dubai,
United Arab Emirates
Telephone:
+971 4 371800
Fax Line:
+971 4 364283
Email Address:
[email protected]
In Asia and Middle East
NEC Viewtechnology, Ltd.
Address:
686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,
Kanagawa 258-0017, Japan
Telephone:
+81 465 85 2369
Fax Line:
+81 465 85 2393
Email Address:
[email protected]
WEB Address:
http://www.nec-pj.com
(Regions Covered)
United Arab Emirates
(Regions Covered)
Japan*
Samir Photographic Supplies
Address:
P.O.Box 599, Jeddah 21421, Saudi Arabia
Telephone:
+966 2 6828219
Fax Line:
+966 2 6830820
Email Address:
[email protected]
NEC Hong Kong Ltd.
Address:
11th Floor, Tower B, New Mandarin Plaza, 14
Science Museum Road,
Tsim Sha Tsui East, Kowloon, Hong Kong
Telephone:
+852 2369 0335
Fax Line:
+852 2795 6618
Email Address:
[email protected]
WEB Address:
http://www.nec.com.hk
(Regions Covered)
Saudi Arabia
NOTE: In countries designated with an asterisk(*), replacement product rental
service are offered.
(Regions Covered)
Hong Kong
NEC Taiwan Ltd.
Address:
Telephone:
Fax Line:
Email Address:
WEB Address:
7F, No.167, SEC.2, Nan King East Road, Taipei,
Taiwan, R.O.C.
+886 2 8500 1734
+886 2 8500 1420
[email protected]
http://www.nec.com.tw
(Regions Covered)
Taiwan
NEC Singapore Pte. Ltd
Address:
401 Commonwealth Drive, #07-02, Haw Par
Technocentre, Singapore 149598
Telephone:
+65 6 273 8333
Fax Line:
+65 6 274 2226
Email Address:
[email protected]
WEB Address:
http://www.nec.com.sg
(Regions Covered)
Singapore
Hyosung Data System, Ltd.
Address:
7th Floor, Cheongdam Building, 52,
Cheongdam-Dong,
Kangnam-Ku, Seoul, Korea 135-100
Telephone:
+82 2 510 0234
Fax Line:
+82 2 540 3590
Email Address:
[email protected]
(Regions Covered)
South Korea
Lenso Communication Co., Ltd.
Address:
292 Lenso House 4, 1st Floor, Srinakarin Road,
Huamark, Bangkapi, Bangkok 10240, Thailand
Telephone:
+66 2 375 2425
Fax Line:
+66 2 375 2434
Email Address:
[email protected]
WEB Address:
http://www.lenso.com
(Regions Covered)
Thailand
E-34
Date:
/
/
P-1/
,
,
TO: NEC or NEC's Authorized Service Station:
FM:
(Company & Name with signature)
Dear Sir (s),
I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your
following conditions, and also the Service fee will be charged to my credit card account, if I don't return the Loan units within the
specified period. I also confirm following information is correct. Regards.
Application Sheet for TravelCare Service Program
Country,
product purchased :
User's Company Name :
User's Company Address :
Phone No., Fax No. :
User's Name :
User's Address :
Phone No., Fax No. :
Local Contact office :
Local Contact office Address :
Phone No., Fax No. :
User's Model Name :
Date of Purchase :
Serial No. on cabinet :
Problem of units per User :
Required Service :
(1) Repair and Return
(2) Loan unit
(1) Credit Card
(2) Travelers Cheque
Requested period of Loan unit :
Payment method :
In Case of Credit Card :
Card No. w/Valid Date :
E-35
(3) Cash
Condition of your TravelCare Service Program
Enduser is requested to understand following condition of TravelCare
Service Program and fill necessary information into the application sheet.
1. Service Options:
There are 3 types of "Service" available. Enduser has to understand
following condition and is required to fill in the Application Sheet.
1) Repair and Return:
The 'Faulty unit' is sent or collected from the customer. It is repaired
and returned within 10 days to the customer, excluding transport time.
There may have a case, repair and return can't be done by NEC
Authorized Service Station, because of shortage of spare parts due
to same model is not sold in the territory.
2) Repair and Return with Loan: (This service is limited to some Service Stations)
5. Loan Service Charges and Conditions:
Upon acceptance of this NEC Projector, Customer agrees to assume
liability for this loan unit.
The current cost of use of this loan unit is $200.00 USD for 12 calendar
days.
If Customer does not return the unit within the 12 calendar days, Customer will be charged the next highest cost up to and including the full
list price to Credit Cards, which price will be informed by NEC Authorized Service Stations. Please see the attached listing of contacts for
each country to arrange for pickup of the loan unit.
If you return to their country of origin with the loan unit, you will be
charged additional freight to return the unit to the loaning country.
Thank you for your understanding of this program.
This service is offered to the Enduser, who cannot wait until their unit
is repaired.
The customer can borrow a unit for $200 up to 12 days. Customer
then sends in inoperable unit to nearest NEC Authorized Service
Station for service. In order to prevent collection problem, Enduser is
required to fill in Application Sheet.
Enduser needs to confirm the availability of the Service to NEC Authorized Service Stations.
3) Loan Only:
For this service, NEC Authorized Service Station supplies the customer with a loan unit for US$200 up to 12 days. Customer keeps the
inoperable unit and when customer returns home, customer arranges
to have the projector serviced in the home country.
2. Warranty Exclusions:
This program does not apply if the Projector's serial number has been
defaced, modified or removed.
If, in the judgement of NEC Authorized Service Station or its agent the
defects or failures result from any cause other than fair wear and tear or
NEC neglect, or fault including the following without limitation:
1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke
or default of or by the Customer its employees or agents or any third
party;
2) Failure or fluctuation of electrical power, electrical circuitry, air conditioning, humidity control or other environmental conditions such as
use it in smoking area;
3) Any fault in the attachments or associated products or components
(whether or not supplied by NEC or its agents which do not form part
of the Product covered by this warranty);
4) Any act of God, fire, flood, war, act of violence or any similar occurrence;
5) Any attempt by any person other than any person authorized by NEC
to adjust, modify, repair, install or service the product.
6) Any Cross-border charges such as, duty, insurance, tax etc.
3. Charges for Warranty Exclusions and Out of Warranty Case:
In case faulty unit is under warranty exclusions case or under Out of
Warranty period, NEC Authorized Service Station will Inform estimation
of actual service cost to the Enduser with reason.
4. Dead on Arrival (DOA):
Enduser must take this issue up with their original supplier in the country of purchase.
NEC Authorized Service Station will repair the DOA unit as a Warranty
repair, but will not exchange DOA unit with new units.
E-36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement