Mitsubishi GOT1000 GT14 Graphic Operation Terminal User's Manual

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".

DANGER

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

Note that the caution level may lead to a serious accident according to the circumstances.

Always follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

DANGER

● Some failures of the GOT, communication unit or cable may keep the outputs on or off.

An external monitoring circuit should be provided to check for output signals which may lead to a serious accident.

Not doing so can cause an accident due to false output or malfunction.

● If a communication fault (including cable disconnection) occurs during monitoring on the GOT, communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant operation to the system by using the switches of a device other than the GOT on the assumption that a GOT communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

● Do not use the GOT as the warning device that may cause a serious accident.

An independent and redundant hardware or mechanical interlock is required to configure the device that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect output or malfunction.

● Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is gone out.

When the GOT backlight goes out, the POWER LED flickers (green/orange) and the display section turns black and causes the monitor screen to appear blank, while the input of the touch switch(s) remains active.

This may confuse an operator in thinking that the GOT is in "screensaver" mode, who then tries to release the GOT from this mode by touching the display section, which may cause a touch switch to operate.

Note that the following occurs on the GOT when the backlight goes out.

• The POWER LED flickers (green/orange) and the monitor screen appears blank.

A - 1

[DESIGN PRECAUTIONS]

DANGER

● The display section is an analog-resistive type touch panel.

If you touch the display section simultaneously in 2 points or more, the switch that is located around the center of the touched point, if any, may operate.

Do not touch the display section in 2 points or more simultaneously.

Doing so may cause an accident due to incorrect output or malfunction.

● When programs or parameters of the controller (such as a PLC) that is monitored by the GOT are changed, be sure to reset the GOT or shut off the power of the GOT at the same time.

Not doing so can cause an accident due to false output or malfunction.

CAUTION

● Do not bundle the control and communication cables with main-circuit, power or other wiring.

Run the above cables separately from such wiring and keep them a minimum of 100mm apart.

Not doing so noise can cause a malfunction.

● Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

● When the GOT is connected to the Ethernet network, the available IP address is restricted according to the system configuration.

• When multiple GOTs are connected to the Ethernet network:

Do not set the IP address (192.168.0.18) for the GOTs and the controllers in the network.

• When a single GOT is connected to the Ethernet network:

Do not set the IP address (192.168.0.18) for the controllers except the GOT in the network.

Doing so can cause the IP address duplication. The duplication can negatively affect the communication of the device with the IP address (192.168.0.18).

The operation at the IP address duplication depends on the devices and the system.

● Turn on the controllers and the network devices to be ready for communication before they communicate with GOT.

Failure to do so can cause a communication error on the GOT.

[MOUNTING PRECAUTIONS]

DANGER

● Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT to/from the panel.

Not switching the power off in all phases can cause a unit failure or malfunction.

A - 2

[MOUNTING PRECAUTIONS]

CAUTION

● Use the GOT in the environment that satisfies the general specifications described in the User's

Manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

● When mounting the GOT to the panel, tighten the mounting screws within the specified torque range.

Undertightening can cause the GOT to drop, short or malfunction. Also, undertightening can disable waterproof or oil proof effect.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the

GOT.

Also, "distortion" of the GOT or the panel may disable waterproof or oil proof effect.

● Never drop cutting chips and electric wire chips into the ventilation window of the GOT when you drill screw holes or perform wiring.

Otherwise, fire, failure or malfunction may be caused.

● When inserting/removing a SD card into/from the GOT, turn the SD card access switch off in advance.

Failure to do so may corrupt data within the SD card.

● When removing a SD card from the GOT, make sure to support the SD card by hand, as it may pop out.

Failure to do so may cause the SD card to drop from the GOT and break.

● When installing a USB memory to the GOT, make sure to install the USB memory to the USB interface firmly.

Failure to do so may cause a malfunction due to poor contact.

● Before removing the USB memory from the GOT, operate the utility screen for removal.

After the successful completion dialog box is displayed, remove the memory by hand carefully.

Failure to do so may cause the USB memory to drop, resulting in a damage or failure of the memory.

● Operate and store the GOT in environments without direct sunlight, high temperature, dust, humidity, and vibrations.

● When using the GOT in the environment of oil or chemicals, use the protective cover for oil.

Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT.

A - 3

[WIRING PRECAUTIONS]

DANGER

● Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

● Always ground the FG terminal of the GOT power to the protective ground conductors dedicated to the GOT.

Not doing so may cause an electric shock or malfunction.

● Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product.

Not doing so can cause a fire or failure.

● Tighten the terminal screws of the GOT power supply section in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.

● Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.

Not doing so can cause a fire, failure or malfunction.

CAUTION

● The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault.

● When unplugging the cable connected to the unit, do not hold and pull the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault.

● Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range.

Undertightening can cause a short circuit or malfunction. Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

[TEST OPERATION PRECAUTIONS]

DANGER

● Before performing the test operations of the user creation monitor screen (such as turning ON or

OFF bit device, changing the word device current value, changing the settings or current values of the timer or counter, and changing the buffer memory current value), read through the manual carefully and make yourself familiar with the operation method.

During test operation, never change the data of the devices which are used to perform significant operation for the system.

False output or malfunction can cause an accident.

A - 4

[STARTUP/MAINTENANCE PRECAUTIONS]

DANGER

● When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

● Correctly connect the battery connector.

Do not charge, disassemble, heat, short-circuit, solder, or throw the battery into the fire.

Doing so will cause the battery to produce heat, explode, or ignite, resulting in injury and fire.

● Before starting cleaning or terminal screw retightening, always switch off the power externally in all phases.

Not switching the power off in all phases can cause a unit failure or malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

CAUTION

● Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

● Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

● Do not drop or apply strong impact to the unit.

Doing so may damage the unit.

● Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

● For repair of the backlight, contact your local Mitsubishi (Electric System) Service.

● Before touching the unit, always touch grounded metal, etc. to discharge static electricity from human body, etc.

Not doing so can cause the unit to fail or malfunction.

● Replace battery with GT11-50BAT by Mitsubishi electric Co. only.

Use of another battery may present a risk of fire or explosion.

● Dispose of used battery promptly.

Keep away from children. Do not disassemble and do not dispose of in fire.

A - 5

[DISPOSAL PRECAUTIONS]

CAUTION

● When disposing of the product, handle it as industrial waste.

● When disposing of this product, treat it as industrial waste. When disposing of batteries, separate them from other wastes according to the local regulations.

(For details of the battery directive in EU member states, refer to the User's Manual of the GOT to be used.)

[TOUCH PANEL PRECAUTIONS]

CAUTION

● For the analog-resistive film type touch panels, normally the adjustment is not required. However, the difference between a touched position and the object position may occur as the period of use elapses. When any difference between a touched position and the object position occurs, execute the touch panel calibration.

● When any difference between a touched position and the object position occurs, other object may be activated. This may cause an unexpected operation due to incorrect output or malfunction.

[TRANSPORTATION PRECAUTIONS]

CAUTION

● When transporting lithium batteries, make sure to treat them based on the transport regulations.

(For details on models subject to restrictions, refer to the User's Manual for the GOT you are using.)

● Before transporting the GOT, turn the GOT power on and check that the battery voltage status is normal on the Time setting & display screen (utilities screen). In addition, confirm that the adequate battery life remains on the rating plate.

Transporting the GOT with the low battery voltage or the battery the reached battery life may unstabilize the backup data unstable during transportation.

● Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the

User's Manual, as they are precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

A - 6

INTRODUCTION

Thank you for choosing Mitsubishi Graphic Operation Terminal (Mitsubishi GOT).

Read this manual and make sure you understand the functions and performance of the GOT thoroughly in advance to ensure correct use.

CONTENTS

SAFETY PRECAUTIONS .........................................................................................................................A - 1

INTRODUCTION ......................................................................................................................................A - 7

CONTENTS ..............................................................................................................................................A - 7

MANUALS...............................................................................................................................................A - 13

QUICK REFERENCE .............................................................................................................................A - 13

ABBREVIATIONS AND GENERIC TERMS ...........................................................................................A - 15

HOW TO READ THIS MANUAL .............................................................................................................A - 20

1. OVERVIEW

1.1

Features........................................................................................................................................... 1 - 2

1.1.1

Rough procedure.................................................................................................................. 1 - 3

2. SYSTEM CONFIGURATION

2.1

Overall Configuration ....................................................................................................................... 2 - 1

2.2

System Equipment........................................................................................................................... 2 - 1

2.2.1

GOT (GT14) ......................................................................................................................... 2 - 2

2.2.2

Option ................................................................................................................................... 2 - 3

3. SPECIFICATIONS

3.1

General Specifications..................................................................................................................... 3 - 1

3.2

Performance Specifications ............................................................................................................. 3 - 2

3.3

Power Supply Specifications ........................................................................................................... 3 - 3

4. PARTS NAME

4.1

Front Panel ...................................................................................................................................... 4 - 1

4.2

Back Panel....................................................................................................................................... 4 - 2

4.3

Rear Face ........................................................................................................................................ 4 - 3

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.1

UL, cUL Standards .......................................................................................................................... 5 - 1

5.2

EMC Directive.................................................................................................................................. 5 - 1

5.2.1

Requirements to Meet EMC Directive .................................................................................. 5 - 2

5.2.2

EMC Directive-Compliant System Configuration .................................................................. 5 - 4

5.2.3

Precautions for Wiring/Connecting the EMC Directive-Compliant Product .......................... 5 - 5

A - 7

6. INSTALLATION

6.1

Control Panel Inside Dimensions for Mounting GOT ....................................................................... 6 - 1

6.2

Panel Cutting Dimension ................................................................................................................. 6 - 2

6.3

Mounting Position ............................................................................................................................ 6 - 2

6.4

Control Panel Temperature and Mounting Angle ............................................................................ 6 - 3

6.5

Installation Procedure ...................................................................................................................... 6 - 4

7. WIRING

7.1

Power Supply Wiring ....................................................................................................................... 7 - 2

7.1.1

Wiring example ..................................................................................................................... 7 - 2

7.1.2

Grounding the GOT .............................................................................................................. 7 - 2

7.1.3

The cause of malfunctions related wiring/Remedy ............................................................... 7 - 3

7.2

Wiring inside and outside the panel................................................................................................. 7 - 5

7.2.1

Wiring inside ......................................................................................................................... 7 - 5

7.2.2

Outside the panel.................................................................................................................. 7 - 5

7.2.3

Attaching surge killers to control equipment ......................................................................... 7 - 6

8. OPTION

8.1

SD Card ........................................................................................................................................... 8 - 1

8.1.1

Applicable SD card ............................................................................................................... 8 - 1

8.1.2

Installing and removing procedures of the SD card.............................................................. 8 - 1

8.2

USB Memory ................................................................................................................................... 8 - 3

8.2.1

Applicable USB memory....................................................................................................... 8 - 3

8.2.2

Installing and removing procedures of the USB memory ..................................................... 8 - 3

8.3

Battery ............................................................................................................................................. 8 - 4

8.3.1

Applicable battery ................................................................................................................. 8 - 4

8.3.2

Battery specifications............................................................................................................ 8 - 4

8.3.3

Battery replacement procedure ............................................................................................ 8 - 5

8.4

Protective Sheet .............................................................................................................................. 8 - 6

8.4.1

Applicable protective sheet................................................................................................... 8 - 6

8.4.2

Installing procedure .............................................................................................................. 8 - 6

8.5

Protective Cover for Oil.................................................................................................................... 8 - 7

8.5.1

Applicable protective cover for oil ......................................................................................... 8 - 7

8.5.2

Installing procedure .............................................................................................................. 8 - 7

8.6

USB Environmental Protection Cover.............................................................................................. 8 - 9

8.6.1

Applicable USB environmental protection cover................................................................... 8 - 9

8.6.2

Installing procedure .............................................................................................................. 8 - 9

8.7

Stand ............................................................................................................................................. 8 - 10

8.7.1

Applicable stand ................................................................................................................. 8 - 10

8.7.2

Installing procedure ............................................................................................................ 8 - 10

8.8

Connector Conversion Adapter ..................................................................................................... 8 - 11

8.8.1

Applicable connector conversion adapter........................................................................... 8 - 11

8.8.2

Installing procedure of connector conversion adapter ........................................................ 8 - 11

8.9

Serial Multi-Drop Connection Unit ................................................................................................. 8 - 12

8.9.1

Serial multi-drop connection unit ........................................................................................ 8 - 12

8.9.2

Applicable serial multi-drop connection unit ....................................................................... 8 - 12

8.9.3

Installation........................................................................................................................... 8 - 12

A - 8

8.9.4

Parts name ......................................................................................................................... 8 - 13

8.9.5

Caution for compliance with EMC Directive ....................................................................... 8 - 13

8.10 Panel-Mounted USB Port Extension.............................................................................................. 8 - 14

8.10.1 Applicable panel-mounted USB port extension .................................................................. 8 - 14

8.10.2 Parts name ......................................................................................................................... 8 - 14

8.10.3 Installing procedure ............................................................................................................ 8 - 14

8.11 RS-232/485 Signal Conversion Adapter........................................................................................ 8 - 16

8.11.1 Applicable RS-232/485 signal conversion adapter ............................................................. 8 - 16

8.11.2 Installing procedure of RS-232/485 signal conversion adapter .......................................... 8 - 16

9. UTILITY FUNCTION

9.1

Utility Execution ............................................................................................................................... 9 - 1

9.2

Utility Function List........................................................................................................................... 9 - 2

9.3

Utility Display ................................................................................................................................... 9 - 4

9.3.1

Display operation of main menu ........................................................................................... 9 - 6

9.3.2

Utility basic configuration...................................................................................................... 9 - 8

9.3.3

Basic operation of settings change....................................................................................... 9 - 9

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1

Communication setting .................................................................................................................. 10 - 1

10.1.1

Communication setting functions........................................................................................ 10 - 1

10.1.2

Display operation of Communication Setting...................................................................... 10 - 1

10.1.3

Communication setting contents ........................................................................................ 10 - 2

10.1.4

Communication setting operation ....................................................................................... 10 - 4

10.2

Communication Detail Setting ....................................................................................................... 10 - 8

10.2.1

Communication detail setting functions .............................................................................. 10 - 8

10.2.2

Display operation of Communication Detail setting ............................................................ 10 - 8

10.2.3

Display contents of Communication Detail setting ........................................................... 10 - 10

10.3

Ethernet Setting ........................................................................................................................... 10 - 15

10.3.1

Ethernet setting functions ................................................................................................. 10 - 15

10.3.2

Display operation of Ethernet setting................................................................................ 10 - 15

10.3.3

Display contents of Ethernet setting ................................................................................. 10 - 16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.1

Display Setting............................................................................................................................... 11 - 1

11.1.1

Function of Display ............................................................................................................. 11 - 1

11.1.2

Display operation of Display ............................................................................................... 11 - 2

11.1.3

Display operations .............................................................................................................. 11 - 3

11.2

Operation Setting (Settings Regarding Operation) ........................................................................ 11 - 6

11.2.1

Operation setting functions................................................................................................. 11 - 6

11.2.2

Display operation of Operation ........................................................................................... 11 - 7

11.2.3

Setting operation of operation ............................................................................................ 11 - 8

11.2.4

Security level change ......................................................................................................... 11 - 9

11.2.5

Utility Call Key Setting ...................................................................................................... 11 - 11

11.2.6

Adjusting the touch panel position (Touch panel calibration) ........................................... 11 - 13

11.2.7

USB mouse/keyboard setting ........................................................................................... 11 - 15

11.3

Transparent Mode Setting ........................................................................................................... 11 - 17

11.4

Backup/Restoration Setting ......................................................................................................... 11 - 18

11.5

Behavior of Duplicate IPs ............................................................................................................ 11 - 21

A - 9

12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY

(TIME SETTING AND DISPLAY)

12.1

Time Setting and Display............................................................................................................... 12 - 1

12.1.1

Time setting and display functions...................................................................................... 12 - 1

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.1

Data Storage Location ................................................................................................................... 13 - 1

13.1.1

Data type and storage location ........................................................................................... 13 - 1

13.1.2

OS version confirmation ..................................................................................................... 13 - 3

13.1.3

Capacity confirmation of the project data downloading location......................................... 13 - 4

13.1.4

Display file .......................................................................................................................... 13 - 4

13.2

Various Data Control ..................................................................................................................... 13 - 5

13.2.1

OS information.................................................................................................................... 13 - 5

13.2.2

Alarm information.............................................................................................................. 13 - 11

13.2.3

Project Information............................................................................................................ 13 - 17

13.2.4

Hard copy information....................................................................................................... 13 - 27

13.2.5

Advanced recipe information ............................................................................................ 13 - 33

13.2.6

Logging information .......................................................................................................... 13 - 53

13.2.7

Memory card format.......................................................................................................... 13 - 63

13.2.8

Memory information .......................................................................................................... 13 - 65

13.2.9

USB device status display ................................................................................................ 13 - 66

13.2.10 SRAM control.................................................................................................................... 13 - 68

13.2.11 GOT data package acquisition ......................................................................................... 13 - 73

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.1

Debug ............................................................................................................................................ 14 - 1

14.1.1

System monitor................................................................................................................... 14 - 1

14.1.2

A list editor .......................................................................................................................... 14 - 1

14.1.3

FX list editor........................................................................................................................ 14 - 1

14.1.4

Backup/restoration.............................................................................................................. 14 - 2

14.2

Self Check ..................................................................................................................................... 14 - 3

14.2.1

Memory check .................................................................................................................... 14 - 3

14.2.2

Drawing check .................................................................................................................... 14 - 6

14.2.3

Font check ........................................................................................................................ 14 - 10

14.2.4

Touch panel check............................................................................................................ 14 - 12

14.2.5

I/O check........................................................................................................................... 14 - 14

14.3

System Alarm Display.................................................................................................................. 14 - 17

14.4

GOT start time ............................................................................................................................. 14 - 19

15. CLEANING DISPLAY SECTION (CLEAN)

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.1

BootOS and Standard Monitor OS Required for Installation ......................................................... 16 - 2

16.2

Prior Preparations for Installing BootOS and Standard Monitor OS .............................................. 16 - 3

16.3

BootOS and Standard Monitor OS Installation Using SD card or USB Memory............................ 16 - 4

16.3.1

Installing when starting the GOT ........................................................................................ 16 - 5

16.3.2

Installing using the program/data control function (Utility) .................................................. 16 - 7

16.4

When Installing the Different Version of BootOS, Standard Monitor OS ....................................... 16 - 9

A - 10

16.5

CoreOS........................................................................................................................................ 16 - 11

16.5.1

Installing the CoreOS ....................................................................................................... 16 - 11

16.5.2

When the CoreOS cannot be installed ............................................................................. 16 - 13

17. MAINTENANCE AND INSPECTION

17.1

Daily Inspection ............................................................................................................................. 17 - 2

17.2

Periodic Inspection ........................................................................................................................ 17 - 2

17.3

Cleaning Method............................................................................................................................ 17 - 3

17.4

Battery Voltage Low Detection and Battery Replacement............................................................. 17 - 4

17.5

Backlight Shutoff Detection............................................................................................................ 17 - 7

17.5.1

Backlight shutoff detection and external alarm ................................................................... 17 - 7

18. TROUBLESHOOTING

18.1

GOT Restoration Sheet ................................................................................................................. 18 - 1

18.2

Error Message and System Alarm............................................................................................... 18 - 11

18.2.1

Error contents display....................................................................................................... 18 - 11

18.2.2

List of error message/system alarm ................................................................................. 18 - 13

APPENDICES

Appendix.1 External Dimensions..........................................................................................................App - 1

Appendix.2 Usage Condition of Utility Function ...................................................................................App - 7

Appendix.3 Transportation Precautions ...............................................................................................App - 9

Appendix.3.1 Relevant models...........................................................................................................App - 9

Appendix.3.2 Transportation guidelines .............................................................................................App - 9

INDEX

REVISIONS

A - 11

A - 12

MANUALS

The following table lists the manual relevant to this product.

Refer to each manual for any purpose.

Manual Name

GT Works3 Version1 Installation Procedure Manual

GT Designer3 Version1 Screen Design Manual (Fundamentals) 1/2, 2/2

GT Designer3 Version1 Screen Design Manual (Functions) 1/2, 2/2

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

GOT1000 Series Connection Manual (Non-Mitsubishi Products 1) for GT Works3

GOT1000 Series Connection Manual (Non-Mitsubishi Products 2) for GT Works3

GOT1000 Series Connection Manual (Microcomputer, MODBUS Products, Peripherals) for GT

Works3

GT Simulator3 Version1 Operating Manual for GT Works3

GOT1000 Series User's Manual (Extended Functions, Option Functions) for GT Works3

Packaging

Enclosed in product

Stored in CD-ROM

Stored in CD-ROM

Stored in CD-ROM

Stored in CD-ROM

Stored in CD-ROM

Stored in CD-ROM

Stored in CD-ROM

Stored in CD-ROM

QUICK REFERENCE

„

Creating a project

Obtaining the specifications and operation methods of GT Designer3

Setting available functions on GT Designer3

GT Designer3 Version1 Screen Design Manual

(Fundamentals) 1/2, 2/2

Creating a screen displayed on the GOT

Obtaining useful functions to increase efficiency of drawing

Setting details for figures and objects

Setting functions for the data collection or trigger action

Setting functions to use peripheral devices

Simulating a created project on a personal computer

GT Designer3 Version1 Screen Design Manual (Functions)

1/2, 2/2

GT Simulator3 Version1 Operating Manual for GT Works3

„

Connecting a controller to the GOT

Obtaining information of Mitsubishi products applicable to the GOT

Connecting Mitsubishi products to the GOT

Connecting multiple controllersto one GOT (Multi-channel function)

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

Establishing communication between a personal computer and a controller via the GOT (FA transparent function)

Manual Number

(Model code)

-

SH-080866ENG

(1D7MB9)

SH-080867ENG

(1D7MC1)

SH-080868ENG

(1D7MC2)

SH-080869ENG

(1D7MC3)

SH-080870ENG

(1D7MC4)

SH-080871ENG

(1D7MC5)

SH-080861ENG

(1D7MB1)

SH-080863ENG

(1D7MB3)

A - 13

Obtaining information of Non-Mitsubishi products applicable to the

GOT

Connecting Non-Mitsubishi products to the GOT

• GOT1000 Series Connection Manual (Non-Mitsubishi

Products 1) for GT Works3

• GOT1000 Series Connection Manual (Non-Mitsubishi

Products 2) for GT Works3

Obtaining information of peripheral devices applicable to the GOT

Connecting peripheral devices including a barcode reader to the GOT

GOT1000 Series Connection Manual (Microcomputer,

MODBUS Products, Peripherals) for GT Works3

„

Transferring data to the GOT

Writing data to the GOT

Reading data from the GOT

GT Designer3 Version1 Screen Design Manual

(Fundamentals) 1/2, 2/2

Verifying a editing project to a GOT project

„

Others

Configuring the extended function and option function

GOT1000 Series User's Manual (Extended Functions, Option

Functions) for GT Works3

A - 14

ABBREVIATIONS AND GENERIC TERMS

„

GOT

Abbreviations and generic terms

GT1695

GT1685

GT1695M-X

GT1685M-S

GT1675

GT1672

GT1665

GT1662

GT16

GT1595

GT1585

GT157

GT1675M-S

GT1675M-V

GT1675-VN

GT1672-VN

GT1665M-S

GT1665M-V

GT1662-VN

GT1595-X

GT1585V-S

GT1585-S

GT1575V-S

GT1575-S

GT1575-V

GT1575-VN

GOT1000

Series

GT156

GT155

GT1572-VN

GT1565-V

GT1562-VN

GT1555-V

GT1555-Q

GT1550-Q

GT15

GT145

GT1455-Q

GT1450-Q

GT14

GT1275

GT1265

GT12

GT1275-V

GT1265-V

GT115

GT11

GT105

GT104

GT1030

GT1020

GT10

GT1155-Q

GT1150-Q

GT1055-Q

GT1050-Q

GT1045-Q

GT1040-Q

Description

Abbreviation of GT1695M-XTBA, GT1695M-XTBD

Abbreviation of GT1685M-STBA, GT1685M-STBD

Abbreviation of GT1675M-STBA, GT1675M-STBD

Abbreviation of GT1675M-VTBA, GT1675M-VTBD

Abbreviation of GT1675-VNBA, GT1675-VNBD

Abbreviation of GT1672-VNBA, GT1672-VNBD

Abbreviation of GT1665M-STBA, GT1665M-STBD

Abbreviation of GT1665M-VTBA, GT1665M-VTBD

Abbreviation of GT1662-VNBA, GT1662-VNBD

Abbreviation of GT1695, GT1685, GT1675, GT1672, GT1665, GT1662,

GT1655,

GT16 Handy GOT

Abbreviation of GT1595-XTBA, GT1595-XTBD

Abbreviation of GT1585V-STBA, GT1585V-STBD

Abbreviation of GT1585-STBA, GT1585-STBD

Abbreviation of GT1575V-STBA, GT1575V-STBD

Abbreviation of GT1575-STBA, GT1575-STBD

Abbreviation of GT1575-VTBA, GT1575-VTBD

Abbreviation of GT1575-VNBA, GT1575-VNBD

Abbreviation of GT1572-VNBA, GT1572-VNBD

Abbreviation of GT1565-VTBA, GT1565-VTBD

Abbreviation of GT1562-VNBA, GT1562-VNBD

Abbreviation of GT1555-VTBD

Abbreviation of GT1555-QTBD, GT1555-QSBD

Abbreviation of GT1550-QLBD

Abbreviation of GT1595, GT1585, GT157 , GT156 , GT155

Abbreviation of GT1455-QTBD, GT1455-QTBDE

Abbreviation of GT1450-QLBD, GT1450-QLBDE

Abbreviation of GT1455-QTBD, GT1455-QTBDE, GT1450-QLBD, GT1450-QLBDE

Abbreviation of GT1275-VNBA, GT1275-VNBD

Abbreviation of GT1265-VNBA, GT1265-VNBD

Abbreviation of GT1275, GT1265

Abbreviation of GT1155-QTBDQ, GT1155-QSBDQ, GT1155-QTBDA, GT1155-QSBDA,

GT1155-QTBD, GT1155-QSBD

Abbreviation of GT1150-QLBDQ, GT1150-QLBDA, GT1150-QLBD

Abbreviation of GT115 , GT11 Handy GOT

Abbreviation of GT1055-QSBD

Abbreviation of GT1050-QBBD

Abbreviation of GT1045-QSBD

Abbreviation of GT1040-QBBD

Abbreviation of GT1030-LBD, GT1030-LBD2, GT1030-LBL, GT1030-LBDW, GT1030-LBDW2,

GT1030-LBLW, GT1030-LWD, GT1030-LWD2, GT1030-LWL, GT1030-LWDW, GT1030-LWDW2,

GT1030-LWLW, GT1030-HBD, GT1030-HBD2, GT1030-HBL, GT1030-HBDW, GT1030-HBDW2,

GT1030-HBLW, GT1030-HWD, GT1030-HWD2, GT1030-HWL, GT1030-HWDW, GT1030-HWDW2,

GT1030-HWLW

Abbreviation of GT1020-LBD, GT1020-LBD2, GT1020-LBL, GT1020-LBDW, GT1020-LBDW2,

GT1020-LBLW, GT1020-LWD, GT1020LWD2, GT1020-LWL, GT1020-LWDW, GT1020-LWDW2,

GT1020-LWLW

Abbreviation of GT105 , GT104 , GT1030, GT1020

A - 15

Abbreviations and generic terms

GOT1000

Series

Handy

GOT

GT16

Handy

GOT

GT11

Handy

GOT

GT1665HS-V

GT1155HS-Q

GT1150HS-Q

Abbreviation of GT1665HS-VTBD

Abbreviation of GT1155HS-QSBD

Abbreviation of GT1150HS-QLBD

GT SoftGOT1000 Abbreviation of GT SoftGOT1000

Description

„

Communication unit

Abbreviations and generic terms

Bus connection unit

Serial communication unit

RS-422 conversion unit

Ethernet communication unit

MELSECNET/H communication unit

Description

GT15-QBUS, GT15-QBUS2, GT15-ABUS, GT15-ABUS2, GT15-75QBUSL, GT15-75QBUS2L,

GT15-75ABUSL, GT15-75ABUS2L

GT15-RS2-9P, GT15-RS4-9S, GT15-RS4-TE

GT15-RS2T4-9P, GT15-RS2T4-25P

GT15-J71E71-100

GT15-J71LP23-25, GT15-J71BR13

MELSECNET/10 communication unit

GT15-75J71LP23-Z

*1

, GT15-75J71BR13-Z

*2

CC-Link IE Controller Network communication unit GT15-J71GP23-SX

CC-Link IE Field Network communication unit GT15-J71GF13-T2

CC-Link communication unit

CC-Link interface unit

GT15-J61BT13, GT15-75J61BT13-Z

*3

GT11HS-CCL, GT11H-CCL

Interface converter unit

Serial multi-drop connection unit

Connection Conversion Adapter

RS-232/485 signal conversion adapter

GT15-75IF900

GT01-RS4-M

GT10-9PT5S

GT14-RS2T4-9P

*1 A9GT-QJ71LP23 + GT15-75IF900 set

*2 A9GT-QJ71BR13 + GT15-75IF900 set

*3 A8GT-J61BT13 + GT15-75IF900 set

„

Option unit

Abbreviations and generic terms

Printer unit

Video/RGB unit

Video input unit

RGB input unit

Video/RGB input unit

RGB output unit

Multimedia unit

CF card unit

CF card extension unit

*1

External I/O unit

Sound output unit

GT15-PRN

GT16M-V4, GT15V-75V4

GT16M-R2, GT15V-75R1

GT16M-V4R1, GT15V-75V4R1

GT16M-ROUT, GT15V-75ROUT

GT16M-MMR

GT15-CFCD

GT15-CFEX-C08SET

GT15-DIO, GT15-DIOR

GT15-SOUT

*1 GT15-CFEX + GT15-CFEXIF + GT15-C08CF set.

Description

A - 16

„

Option

Abbreviations and generic terms

CF card

Memory card adaptor

SD card

Option function board

Battery

Protective Sheet

Protective cover for oil

USB environmental protection cover

Stand

Attachment

Backlight

Multi-color display board

Connector conversion box

Emergency stop sw guard cover

Memory loader

Memory board

Panel-mounted USB port extension

Description

GT05-MEM-16MC, GT05-MEM-32MC, GT05-MEM-64MC, GT05-MEM-128MC,

GT05-MEM-256MC, GT05-MEM-512MC, GT05-MEM-1GC, GT05-MEM-2GC,

GT05-MEM-4GC, GT05-MEM-8GC, GT05-MEM-16GC

GT05-MEM-ADPC

L1MEM-2GBSD, L1MEM-4GBSD

GT16-MESB, GT15-FNB, GT15-QFNB, GT15-QFNB16M, GT15-QFNB32M,

GT15-QFNB48M, GT11-50FNB, GT15-MESB48M

GT15-BAT, GT11-50BAT

For GT16

For GT15

GT16-90PSCB, GT16-90PSGB, GT16-90PSCW, GT16-90PSGW,

GT16-80PSCB, GT16-80PSGB, GT16-80PSCW, GT16-80PSGW,

GT16-70PSCB, GT16-70PSGB, GT16-70PSCW, GT16-70PSGW,

GT16-60PSCB, GT16-60PSGB, GT16-60PSCW, GT16-60PSGW,

GT16-50PSCB, GT16-50PSGB, GT16-50PSCW, GT16-50PSGW,

GT16-90PSCB-012, GT16-80PSCB-012, GT16-70PSCB-012,

GT16-60PSCB-012, GT16-50PSCB-012, GT16H-60PSC

GT15-90PSCB, GT15-90PSGB, GT15-90PSCW, GT15-90PSGW,

GT15-80PSCB, GT15-80PSGB, GT15-80PSCW, GT15-80PSGW,

GT15-70PSCB, GT15-70PSGB, GT15-70PSCW, GT15-70PSGW,

GT15-60PSCB, GT15-60PSGB, GT15-60PSCW, GT15-60PSGW,

GT15-50PSCB, GT15-50PSGB, GT15-50PSCW, GT15-50PSGW

GT14-50PSCB, GT14-50PSGB, GT14-50PSCW, GT14-50PSGW

GT11-70PSCB, GT11-65PSCB

For GT14

For GT12

For GT11

For GT10

GT11-50PSCB, GT11-50PSGB, GT11-50PSCW, GT11-50PSGW,

GT11H-50PSC

GT10-50PSCB, GT10-50PSGB, GT10-50PSCW, GT10-50PSGW,

GT10-40PSCB, GT10-40PSGB, GT10-40PSCW, GT10-40PSGW,

GT10-30PSCB, GT10-30PSGB, GT10-30PSCW, GT10-30PSGW,

GT10-20PSCB, GT10-20PSGB, GT10-20PSCW, GT10-20PSGW

GT05-90PCO, GT05-80PCO, GT05-70PCO, GT05-60PCO, GT05-50PCO,

GT16-50PCO, GT10-40PCO, GT10-30PCO, GT10-20PCO

GT16-UCOV, GT16-50UCOV, GT15-UCOV, GT14-50UCOV, GT11-50UCOV

GT15-90STAND, GT15-80STAND, GT15-70STAND, A9GT-50STAND, GT05-50STAND

GT15-70ATT-98, GT15-70ATT-87, GT15-60ATT-97, GT15-60ATT-96,

GT15-60ATT-87, GT15-60ATT-77, GT15-50ATT-95W, GT15-50ATT-85

GT16-90XLTT, GT16-80SLTT, GT16-70VLTN, GT16-70VLTTA, GT16-60VLTN, GT15-90XLTT,

GT15-80SLTT, GT16-70SLTT, GT16-70VLTT, GT16-60SLTT, GT16-60VLTT,

GT15-70SLTT, GT15-70VLTT, GT15-70VLTN, GT15-60VLTT, GT15-60VLTN

GT15-XHNB, GT15-VHNB

GT11H-CNB-37S, GT16H-CNB-42S

GT11H-50ESCOV, GT16H-60ESCOV

GT10-LDR

GT10-50FMB

GT10-C10EXUSB-5S, GT14-C10EXUSB-4S

A - 17

„

Software

Abbreviations and generic terms

GT Works3

GT Designer3

GT Simulator3

GT SoftGOT1000

GT Converter2

GT Designer2 Classic

GT Designer2 iQ Works

MELSOFT Navigator

GX Works2

GX Simulator2

GX Simulator

GX Developer

GX LogViewer

PX Developer

MT Works2

MT Developer

MR Configurator2

MR Configurator

FR Configurator

NC Configurator

FX Configurator-FP

FX3U-ENET-L Configuration tool

RT ToolBox2

MX Component

MX Sheet

LCPU Logging Configuration Tool

Description

Abbreviation of the SW DNC-GTWK3-E and SW DNC-GTWK3-EA

Abbreviation of screen drawing software GT Designer3 for GOT1000 series

Abbreviation of screen simulator GT Simulator3 for GOT1000/GOT900 series

Abbreviation of monitoring software GT SoftGOT1000

Abbreviation of data conversion software GT Converter2 for GOT1000/GOT900 series

Abbreviation of screen drawing software GT Designer2 Classic for GOT900 series

Abbreviation of screen drawing software GT Designer2 for GOT1000/GOT900 series

Abbreviation of iQ Platform compatible engineering environment MELSOFT iQ Works

Generic term for integrated development environment software included in the SW DNC-IQWK (iQ

Platform compatible engineering environment MELSOFT iQ Works)

Abbreviation of SW DNC-GXW2-E and SW DNC-GXW2-EA type programmable controller engineering software

Abbreviation of GX Works2 with the simulation function

Abbreviation of SW D5C-LLT-E(-EV) type ladder logic test tool function software packages

(SW5D5C-LLT (-EV) or later versions)

Abbreviation of SW D5C-GPPW-E(-EV)/SW D5F-GPPW-E type software package

Abbreviation of SW DNN-VIEWER-E type software package

Abbreviation of SW D5C-FBDQ-E type FBD software package for process control

Abbreviation of motion controller engineering environment MELSOFT MT Works2

(SW DNC-MTW2-E)

Abbreviation of SW RNC-GSV type integrated start-up support software for motion controller Q series

Abbreviation of SW DNC-MRC2-E type Servo Configuration Software

Abbreviation of MRZJW -SETUP E type Servo Configuration Software

Abbreviation of Inverter Setup Software (FR-SW -SETUP-WE)

Abbreviation of CNC parameter setting support tool NC Configurator

Abbreviation of parameter setting, monitoring, and testing software packages for FX3U-20SSC-H

(SW D5C-FXSSC-E)

Abbreviation of FX3U-ENET-L type Ethernet module setting software (SW1D5-FXENETL-E)

Abbreviation of robot program creation software (3D-11C-WINE)

Abbreviation of MX Component Version (SW D5C-ACT-E, SW D5C-ACT-EA)

Abbreviation of MX Sheet Version (SW D5C-SHEET-E, SW D5C-SHEET-EA)

Abbreviation of LCPU Logging Configuration Tool (SW1DNN-LLUTL-E)

„

License key (for GT SoftGOT1000)

License

Abbreviations and generic terms

GT15-SGTKEY-U, GT15-SGTKEY-P

Description

A - 18

„

Others

Abbreviations and generic terms

IAI

OMRON

KEYENCE

KOYO EI

SHARP

JTEKT

SHINKO

CHINO

TOSHIBA

TOSHIBA MACHINE

HITACHI IES

HITACHI

FUJI FA

PANASONIC

PANASONIC EW

FUJI SYS

YASKAWA

YAMATAKE

YOKOGAWA

ALLEN-BRADLEY

GE FANUC

LS IS

SCHNEIDER

SICK

SIEMENS

RKC

HIRATA

MURATEC

PLC

Temperature controller

Indicating controller

Controller

PC CPU module

GOT (server)

GOT (client)

Windows

®

font

Intelligent function module

MODBUS

®

/RTU

MODBUS

®

/TCP

Description

Abbreviation of IAI Corporation

Abbreviation of OMRON Corporation

Abbreviation of KEYENCE CORPORATION

Abbreviation of KOYO ELECTRONICS INDUSTRIES CO., LTD.

Abbreviation of Sharp Manufacturing Systems Corporation

Abbreviation of JTEKT Corporation

Abbreviation of Shinko Technos Co., Ltd.

Abbreviation of CHINO CORPORATION

Abbreviation of TOSHIBA CORPORATION

Abbreviation of TOSHIBA MACHINE CO., LTD.

Abbreviation of Hitachi Industrial Equipment Systems Co., Ltd.

Abbreviation of Hitachi, Ltd.

Abbreviation of Fuji Electric FA Components & Systems Co., Ltd.

Abbreviation of Panasonic Corporation

Abbreviation of Panasonic Electric Works Co., Ltd.

Abbreviation of Fuji Electric Systems Co., Ltd.

Abbreviation of YASKAWA Electric Corporation

Abbreviation of Yamatake Corporation

Abbreviation of Yokogawa Electric Corporation

Abbreviation of Allen-Bradley products manufactured by Rockwell Automation, Inc.

Abbreviation of GE Fanuc Automation Corporation GE Fanuc Automation Corporation

Abbreviation of LS Industrial Systems Co., Ltd.

Abbreviation of Schneider Electric SA

Abbreviation of SICK AG

Abbreviation of Siemens AG

Abbreviation of RKC INSTRUMENT INC.

Abbreviation of Hirata Corporation

Abbreviation of Muratec products manufactured by Muratec Automation Co., Ltd.

Abbreviation of programmable controller

Generic term for temperature controller manufactured by each corporation

Generic term for indicating controller manufactured by each corporation

Generic term for controller manufactured by each corporation

Abbreviation of PC CPU Unit manufactured by CONTEC CO., LTD

Abbreviation of GOTs that use the server function

Abbreviation of GOTs that use the client function

Abbreviation of TrueType font and OpenType font available for Windows

®

(Differs from the True Type fonts settable with GT Designer3)

Indicates the modules other than the PLC CPU, power supply module and I/O module that are mounted to the base unit

Generic term for the protocol designed to use MODBUS

®

protocol messages on a serial communication

Generic term for the protocol designed to use MODBUS

®

protocol messages on a TCP/IP network

A - 19

HOW TO READ THIS MANUAL

„

Symbols

Following symbols are used in this manual.

Refers to the information required.

Refers to information useful for operation.

Indicates the location of related content.

Indicates the operation procedure.

Perform procedures in numerical order.

[ ] : Indicates the setting items displayed

on the software and GOT screen.

: Refers to a button displayed on the

computer screen or the GOT screen,

or a key of the computer keyboard.

5 9 2 0

Since the above page was created for explanation purpose, it differs from the actual page.

A - 20

1.

OVERVIEW

„

About GOT

A GOT is installed on the panel surface of a control panel or operating panel and connects to the PLC within the control panel. The GOT carries out switch operation, lamp display, data display, message display, etc.

PLC

For the display screen, two kinds of screens are available: user screen and utility screen.

(1) User Screen

The user screen is a screen drawn by drawing software.

The objects [Touch switch], [Lamp display], [Comment display], and

[Numeric display] can be arbitrarily arranged on the display.

Moreover, multiple screens created within drawing software can be individually selected or overlapped for the display.

Connector for program

GOT

For details, refer to the following.

GT Designer3 Version1 Screen Design Manual

(2) Utility Screen

The utility screen is a factory drawn horizontal screen that cannot be edited.

Installing the BootOS or Standard monitor OS in the GOT from drawing software, the utility screen is displayed.

The utility screen has options for [Brightness/contrast], [Memory check], etc.

For details, refer to the following.

9. to 18.

2

3

4

5

1

6

7

8

1. OVERVIEW

1 - 1

1.1 Features

Monitoring for turning ON/OFF bit devices of a PLC, forced turning ON/OFF the bit devices of a PLC, monitoring the word device set value/current value and changing that numeric values are easily made.

(1) The display unit is used for engineers' stage replacement, setting change and troubleshooting or for operation guidance to an operator.

• Monitor

• Forced turning ON/OFF

• Set value change

• Trouble check

(2) Improved monitoring performance and connectivity to FA devices

• Multiple languages are displayed using the Unicode2.1-compatible fonts and beautiful characters are drawn using the TrueType and high quality fonts.

• Two types of display modes are provided: 65536-color display and monochrome display

A fine and beautiful full-color display which shows even small characters clearly, is enabled in the 65536-color display by adopting the high intensity, wide viewing angle and high definition TFT color liquid crystal display.

(Also compatible with digital screen displays with 65536 colors, BMP, etc.)

In the monochrome display, 16 scales are used to improve the display.

• High speed monitoring through high speed communication at maximum of 115.2kbps.

• High speed display and high speed touch switch response.

• The operation performance is improved by the analog touch panel.

(3) More efficient GOT operations including screen design, startup, adjustment, management and maintenance works

• The 9MB built-in flash memory is included as standard.

• SD card interface is included as standard.

• RS-232 interface is included as standard.

• RS-422/485 interface is included as standard.

• USB interface (host/device) is included as standard.

• Ethernet interface is included as standard.

• System font types are increased by the adoption of the font installation system.

• Four types of alarms (system alarm, user alarm, alarm history and alarm popup display) are integrated, and realizing an efficient alarm notification.

(4) Enhanced support of FA device setup tools

• Transferring or monitoring the sequence programs using the PC connected to GOT is available, during connection to A, QnA, L, Q, or FX series PLC CPU (FA Transparent function).

1 - 2

1. OVERVIEW

1.1 Features

1.1.1

Rough procedure

The outline procedures before operating GOT and the descriptions of each item are shown below.

Install GT Designer3 in the PC.

Refer to GT Designer3 Version1 Screen Design Manual

(Fundamentals).

Create project data.

Wire for the GOT power supply and the controller.

Refer to GT Designer3 Version1 Screen Design Manual

(Functions).

7. WIRING

Refer to GOT1000 Series Connection Manual for GT Works3.

1

2

3

Wire for the controller power supply and I/O.

Controller manuals

Turn on the power of GOT and controller.

4

Install the OS to GOT.

16. INSTALLATION OF COREOS, BOOTOS AND

STANDARD MONITOR OS

Refer to GT Designer3 Version1 Screen Design Manual

(Fundamentals).

5

Check that the OS is installed to GOT.

Download project data.

Turn on the controller power and check that the GOT recognizes the controller.

Check that the monitoring is normal.

Refer to GT Designer3 Version1 Screen Design Manual

(Fundamentals).

6

7

8

1. OVERVIEW

1.1 Features

1 - 3

1 - 4

1. OVERVIEW

1.1 Features

2.

SYSTEM CONFIGURATION

2.1 Overall Configuration

The overall configuration of GOT is as follows.

For the connection methods applicable to GOT1000 series and cable, refer to the following.

GOT1000 Series Connection Manual for GT Works3

SD card

USB memory

Refer to

8.1.

Refer to

8.2.

Battery

Refer to

8.3.

Protective sheet

Refer to

8.4.

Protective cover for oil

Refer to

8.5.

Stand

Refer to

8.7.

Panel-mounted

USB port extension

Refer to

8.10.

Serial multi-drop connection unit

Refer to

8.9.

Connector conversion adapter

Refer to

8.8.

RS-232/485 signal conversion adapter

Refer to

8.11.

Bar code reader

(Commercially available)

RFID controller

(Commercially available)

USB mouse

(Commercially available)

USB keyboard

(Commercially available)

Personal computer

(Commercially available)

2.2 System Equipment

(1) Explanation of the GOT model name

G T 1 4 5 5 - Q T B D E

Communication interface

Power type

Panel color type

E : Built-in Ethernet

D : DC24V

B : Black

Display device type L : monochrome (black and white)

T : TFT color (High intensity, wide angle view)

Resolution Q : 320×240 (QVGA)

Display color type

Screen size type

GOT1000 series

0 : Monochrome (black and white) 16 scales

5 : 65535 colors

5 : 5.7"

GT14

2. SYSTEM CONFIGURATION

2.1 Overall Configuration

2 - 1

3

4

5

6

7

8

1

2

(2) Explanation of the option model name

G T

* *

-

* * * * * *

50 : Dedicated for 5.7"

16 : Dedicated for GT16

15 : Dedicated for GT15

14 : Dedicated for GT14

11 : Dedicated for GT11

10 : Dedicated for GT10

09 :

05 :

01 :

Common for GT16/GT15/GT14/GT11/GT10

2.2.1

GOT (GT14)

Product name

Model name

GT1455-QTBDE

GOT

GT1455-QTBD

GT1450-QLBDE

GT1450-QLBD

Specifications

5.7" [320 240 dots], TFT color liquid crystal display, 65536 colors,

24VDC, memory size 9MB, built-in battery, built-in Ethernet interface

5.7" [320 240 dots], TFT color liquid crystal display, 65536 colors,

24VDC, memory size 9MB, built-in battery

5.7" [320 240 dots], STN monochrome liquid crystal display, monochrome (black/white),

24VDC, memory size 9MB, built-in battery, built-in Ethernet interface

5.7" [320 240 dots], STN monochrome liquid crystal display, monochrome (black/white),

24VDC, memory size 9MB, built-in battery

2 - 2

2. SYSTEM CONFIGURATION

2.2 System Equipment

2.2.2

Option

Connection cables for MITSUBISHI PLCs (Sold separately)

RS-422 cable

RS-232 cable

Product name Model name

GT01-C10R4-8P

FXCPU direct connection cable, FX expansion board connection cable

GT01-C30R4-8P

GT01-C100R4-8P

GT01-C200R4-8P

GT01-C300R4-8P

QnA/A/FXCPU direct connection cable, computer link connection cable

GT01-C30R4-25P

GT01-C100R4-25P

GT01-C200R4-25P

GT01-C300R4-25P

GT09-C30R4-6C

Computer link connection cable

GT09-C100R4-6C

GT09-C200R4-6C

GT09-C300R4-6C

QCPU direct connection cable

GT01-C30R2-6P

FX expansion board connection, FX special adaptor connection, data transfer cable

GT01-C30R2-9S

FX special adaptor connection

GT01-C30R2-25P

Computer link connection cable

GT09-C30R2-9P

GT09-C30R2-25P

3m

10m

20m

30m

3m

10m

20m

30m

Cable length

1m

3m

10m

20m

30m

3m

3m

3m

3m

3m

For connecting GOT to QCPU

Contents

For connecting GOT to FXCPU (MINI DIN 8pin)

For connecting GOT to FXCPU expansion board (MINI DIN 8pin)

For connecting GOT to QnA/A Motion controller CPU (A series), FXCPU (D-

Sub 25pin)

For connecting GOT to FA-CNV CBL

For connecting GOT to serial communication unit (AJ71QC24(N)-R4)

For connecting GOT to computer link module/serial communication unit

For connecting GOT to FXCPU expansion board (D-Sub 9pin)

For connecting GOT to FXCPU special adaptor (D-Sub 9pin)

For connecting GOT to FXCPU special adaptor (D-Sub 25pin)

For connecting GOT to computer link module/serial communication unit

Connection cables for OMRON PLCs (Sold separately)

Product name

RS-422 cable

RS-422 cable

Model name

GT09-C30R40101-9P

GT09-C100R40101-9P

GT09-C200R40101-9P

GT09-C300R40101-9P

GT09-C30R40103-5T

GT09-C100R40103-5T

GT09-C200R40103-5T

GT09-C300R40103-5T

GT09-C30R40102-9P

GT09-C100R40102-9P

GT09-C200R40102-9P

GT09-C300R40102-9P

20m

30m

3m

10m

20m

30m

Cable length

3m

10m

20m

30m

3m

10m

Contents

For connecting GOT to OMRON PLC, serial communication unit, serial communication board

For connecting GOT to serial communication board

For connecting GOT to OMRON rack type host link unit, communication board

RS-232 cable

GT09-C30R20101-9P

GT09-C30R20102-25S

GT09-C30R20103-25P

3m

3m

3m

For connecting GOT to OMRON PLC, serial communication unit, communication board, serial communication board

For connecting GOT to OMRON connection cable

For connecting GOT to OMRON rack type host link unit

1

2

3

4

5

6

7

8

2. SYSTEM CONFIGURATION

2.2 System Equipment

2 - 3

Connection cables for KEYENCE PLCs (Sold separately)

Product name

RS-422 cable

RS-232 cable

Model name

GT09-C30R41101-5T

GT09-C100R41101-5T

GT09-C200R41101-5T

GT09-C300R41101-5T

GT09-C30R21101-6P

GT09-C30R21102-9S

GT09-C30R21103-3T

Cable length

3m

10m

20m

30m

3m

3m

3m

Contents

For connecting GOT to KEYENCE multi-communication unit

For connecting GOT to KEYENCE PLC

For connecting GOT to KEYENCE multi-communication unit

For connecting GOT to KEYENCE multi-communication unit

Connection cables for Panasonic Electric Works PLCs (Sold separately)

Product name

Model name

GT09-C30R20901-25P

Cable length

3m

RS-232 cable

GT09-C30R20902-9P

GT09-C30R20903-9P

GT09-C30R20904-3C

3m

3m

3m

Contents

For connecting GOT to Panasonic Electric Works RS422/232C conversion adapter

For connecting GOT to the tool port or RS232C port of Panasonic Electric Works PLC, computer communication unit

For connecting GOT to the RS232C port of Panasonic Electric Works PLC

For connecting GOT to the RS232C port of Panasonic Electric Works PLC

Connection cables for YASKAWA PLCs (Sold separately)

Product name

RS-422 cable

RS-232 cable

Model name

GT09-C30R40201-9P

GT09-C100R40201-9P

GT09-C200R40201-9P

GT09-C300R40201-9P

GT09-C30R40202-14P

GT09-C100R40202-14P

GT09-C200R40202-14P

GT09-C300R40202-14P

GT09-C30R20201-9P

GT09-C30R20202-15P

GT09-C30R20203-9P

GT09-C30R20204-14P

GT09-C30R20205-25P

Cable length

3m

10m

20m

30m

3m

10m

20m

30m

3m

3m

3m

3m

3m

For connecting GOT to YASKAWA MEMOBUS module

For connecting GOT to YASKAWA PLC

For connecting GOT to YASKAWA PLC

Contents

For connecting GOT to YASKAWA MEMOBUS module

2 - 4

2. SYSTEM CONFIGURATION

2.2 System Equipment

Connection cables for YOKOGAWA PLCs (Sold separately)

Product name

Model name

RS-422 cable

RS-232 cable

GT09-C30R40301-6T

GT09-C100R40301-6T

GT09-C200R40301-6T

GT09-C300R40301-6T

GT09-C30R40302-6T

GT09-C100R40302-6T

GT09-C200R40302-6T

GT09-C300R40302-6T

GT09-C30R40303-6T

GT09-C100R40303-6T

GT09-C200R40303-6T

GT09-C300R40303-6T

GT09-C30R40304-6T

GT09-C100R40304-6T

GT09-C200R40304-6T

GT09-C300R40304-6T

GT09-C30R20301-9P

GT09-C30R20302-9P

GT09-C30R20304-9S

20m

30m

3m

10m

20m

30m

3m

10m

20m

30m

3m

3m

3m

Cable length

3m

10m

20m

30m

3m

10m

Contents

For connecting GOT to YOKOGAWA PC link module

For connecting GOT to YOKOGAWA temperature controller

For connecting GOT to YOKOGAWA CPU port/D-Sub 9pin conversion cable

For connecting GOT to YOKOGAWA PC link module

For connecting GOT to YOKOGAWA converter

Connection cables for Allen-Bradley PLCs (Sold separately)

Product name

Model name

RS-232 cable

GT09-C30R20701-9S

GT09-C30R20702-25P

Cable length

3m

3m

Contents

For connecting GOT to Allen-Bradley PLC

For connecting GOT to Allen-Bradley Adapter

Connection cables for SIEMENS PLCs (Sold separately)

Product name

Model name

RS-232 cable GT09-C30R20801-9S

Cable length

3m

Contents

For connecting GOT to SIEMENS HMI Adapter

Connection cables for SHINKO indicating controller PLCs (Sold separately)

Product name

Model name

RS-232 cable GT09-C30R21401-4T

Cable length

3m

Contents

For connecting GOT to SHINKO indicating controller

SD card (Sold separately)

SD card

Product name

*1

Model name

L1MEM-2GBSD

L1MEM-4GBSD

SD memory card 2GB

SDHC memory card 4GB

Contents

-

Commercially-available SD card

*1

Some models with the operations checked by our company are usable.

For the operation-checked models, refer to "Operation Check Results of Third Party SD Cards on GT14 Model" (Hime-T-P-0089) separately available.

The Technical News above is available as a reference at the Information site for Mitsubishi industrial automation products

MELFANSweb home page.

(MELFANSweb website: http://wwwf2.mitsubishielectric.co.jp/english/index.html)

1

2

3

4

5

6

7

8

2. SYSTEM CONFIGURATION

2.2 System Equipment

2 - 5

2 - 6

USB memory (Sold separately)

Product name

USB memory -

Model name Contents

Commercially-available USB memory

*2

*2 Some models with the operations checked by our company are usable.

For the operation-checked models, refer to "List of valid devices applicable for GOT1000 series" (T10-0039) separately available.

The Technical News above is available as a reference at the Information site for Mitsubishi industrial automation products

MELFANSweb home page.

(MELFANSweb website: http://wwwf2.mitsubishielectric.co.jp/english/index.html)

Battery (Sold separately)

Battery

Product name

*3

Model name

GT11-50BAT

Contents

Battery for clock data, alarm history, recipe data, time action setting value, advanced alarm, advanced recipe, logging, hard copy, and SRAM user area backups

*3 At GOT purchase, it is installed in the main unit.

Stand (Sold separately)

Product name

Stand

Model name

GT05-50STAND Stand for 5.7"

Contents

Protective cover for oil (Sold separately)

Product name

Protective cover for oil

Model name

GT05-50PCO For 5.7" GOT

Contents

Protective sheet (Sold separately)

Product name

Protective sheet

Model name

GT14-50PSCB

GT14-50PSGB

GT14-50PSCW

GT14-50PSGW

Drawing software (Sold separately)

Product name

GT Designer3

Model name

SW DNC-GTD3-E

( indicates the version.)

5.7" protective sheet

Contents

Clear 5 sheets

Antiglare 5 sheets

Clear (Frame: white) 5 sheets

Antiglare (Frame: white) 5 sheets

Contents

Drawing software for GOT1000 series

PC connection cable (Sold separately)

Product name

Project data transfer cable

Model name

GT09-C30USB-5P

GT01-C30R2-9S

Cable length

3m

3m

Contents

GOT (USB Mini-B) PC (USB)

GOT (D-Sub 9pin) PC (D-Sub 9pin)

Panel-mounted USB port extension (Sold separately)

Product name

Panel-mounted USB port extension

Model name

GT14-C10EXUSB-4S

Cable length

1m

Contents

Panel-mounted USB port extension, compatible with IP67f

Serial multi-drop connection unit (Sold separately)

Product name

Serial multi-drop connection unit

Model name

GT01-RS4-M

Connector conversion adapter (Sold separately)

Product name

Connector conversion adapter

Model name

GT10-9PT5S

For GOT multi-drop connection

For GOT multi-drop connection

Contents

Contents

2. SYSTEM CONFIGURATION

2.2 System Equipment

Bar code reader, RFID controller (Sold separately)

Product name

Bar code reader

RFID controller

*4

Model name

-

Contents

Commercially-available bar code reader

*4

-

Commercially-available RFID controller

*4

Some models with the operations checked by our company are usable.

For the operation-checked models, refer to "List of valid devices applicable for GOT1000 series" (T10-0039) separately available.

The Technical News above is available as a reference at the Information site for Mitsubishi industrial automation products

MELFANSweb home page.

(MELFANSweb website: http://wwwf2.mitsubishielectric.co.jp/english/index.html)

RS-232/485 signal conversion adapter (Sold separately)

Product name

RS-232/485 signal conversion adapter

Model name

GT14-RS2T4-9P

Contents

For GOT multi-drop connection, multi-channel function connection, temperature controller connection, and MODBUS(R)/RTU connection

1

2

3

4

5

6

7

8

2. SYSTEM CONFIGURATION

2.2 System Equipment

2 - 7

2 - 8

2. SYSTEM CONFIGURATION

2.2 System Equipment

3.

SPECIFICATIONS

3.1 General Specifications

Item

Operating ambient temperature

Display section

0 to 50

Other than display section

0 to 55 (when horizontally installed), 0 to 50 (when vertically installed)

Storage ambient temperature

-20 to 60

Operating ambient humidity

Storage ambient humidity

10 to 90%, non-condensing (WBT: 39 )

10 to 90%, non-condensing

Vibration resistance

Shock resistance

Operating atmosphere

Frequency Acceleration

Halfamplitude

3.5mm

Sweep count

Conforms to

JIS B 3502 and

IEC 61131-2

Under intermittent vibration

Under continuous vibration

5 to 9Hz

9 to 150Hz

5 to 9Hz

9 to 150Hz

-

9.8m/s

-

4.9m/s

2

2

-

1.75mm

-

10 times each in

X, Y and Z directions

Conforms to JIS B 3502, IEC 61131-2 (147 m/s 2 , 3 times each in X, Y and Z directions)

Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and must be no direct sunlight. (Same as for saving)

Operating altitude

*1

Installation location

Overvoltage category

*2

Pollution degree

*3

Cooling method

Grounding

2000 m (6562 ft) max.

Inside control panel

II or less

2 or less

Self-cooling

Class D grounding (100 or less), to be connected to the panel when grounding is not possible.

*1

*2

*3

Specifications

Do not use or store the GOT under pressures higher than the atmospheric pressure of altitude 0m (0ft.).

Failure to observe this instruction may cause a malfunction.

When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press, and the sheet may be peeled off.

This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the machinery within the premises.

Category II applies to equipment for which electrical power is supplied from fixed facilities.

The surge voltage withstand level for up to the rated voltage of 300V is 2500V.

This index indicates the degree to which conductive pollution is generated in the environment where the equipment is used.

In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.

2

3

4

5

6

7

1

8

3. SPECIFICATIONS

3.1 General Specifications

3 - 1

3.2 Performance Specifications

The performance specifications are as follows.

Item

Type

Screen size

Resolution

Display size

GT1455-QTBD(E)

TFT color liquid crystal display

5.7"

Specifications

GT1450-QLBD(E)

Monochrome (black/white) liquid crystal display

Display section

*1

Display character

Display color

Display angle

*2

W115(4.53) H86(3.39)[mm](inch) (Horizontal format)

16-dot standard font: 20 characters 15 lines (Horizontal format),

12-dot standard font: 26 characters 20 lines (Horizontal format)

65536 colors

Left/Right: 80 degrees, Top: 80 degrees, Bottom: 60 degrees (Horizontal format)

Monochrome (black/white) 16 scales

Left/Right: 45 degrees, Top: 20 degrees, Bottom: 40 degrees (Horizontal format)

Backlight

Touch panel

Memory

Battery

Built-in interface

*4

Intensity of liquid crystal display only

Contrast adjustment

Intensity adjustment

Life

RS-422/485

RS-232

Ethernet

(Only for models equipped with Ethernet)

USB

SD card

400[cd/m

2

] 300[cd/m

2

]

-

8-level adjustment

32-level adjustment

Approx. 50,000h. (Time for contrast to become 1/5 at operating ambient temperature of 25 )

LED type (irreplaceable)

Backlight off/screen saving time can be set.

*3

Life

Type

Key size

Number of points touched simultaneously

Life

Approx. 70,000h or longer. (Time for display intensity reaches 50% at operating ambient temperature of 25 )

Analog resistive film

Minimum 2 2 dots (per key)

Simultaneous presses not allowed. (Only 1 point can be touched.)

C drive

D drive

*5

Backup target

1 million times (operating force 0.98N max.)

Built-in flash memory, 9Mbytes (for storing project data and OS)

Life (Number of write times): 100,000 times

SRAM (internal), 512Kbytes (battery backup)

GT11-50BAT lithium battery

Clock data, alarm history, recipe data, time action setting value, advanced alarm, advanced recipe, logging, hard copy and SRAM user area

Life

Approx. 5 years (Operating ambient temperature of 25 )

RS-422/485, 1ch

Transmission speed: 115200/57600/38400/19200/9600/4800bps

Connector shape: D-Sub 9pin (Female)

Application: For communicating with a controller

Terminating resistor: Open/110 /330 (Switched by terminating resistor selector switch)

*6

(At factory shipment: 330 )

RS-232, 1ch

Transmission speed: 115200/57600/38400/19200/9600/4800bps

Connector shape: D-Sub 9pin (Male)

Application: For communicating with a controller, connecting a bar code reader/RFID, connecting a PC

(project data upload/download, OS installation, FA transparent function)

Data transfer method: 100BASE-TX, 10BASE-T, 1ch

Connector shape: RJ-45 (modular jack)

Application: For communicating with a controller, using the gateway function, connecting a PC (project data upload/download, OS installation, FA transparent function)

USB (Full Speed 12Mbps), Host, 1ch

Connector shape: TYPE-A

Application: For transferring data, storing data

USB (Full Speed 12Mbps), device, 1ch

Connector shape: Mini-B

Application: For connecting a PC (project data upload/download, OS installation, FA transparent function)

SD standard, 1ch

Supported memory card: SDHC memory card, SD memory card

Application: For uploading/downloading project data, OS installation, storing logging data

Single tone (tone length adjustable) Buzzer output

Protective structure

*7

External dimensions

Weight

Compatible software package

(GT Designer3 version)

IP67f (front section of the panel only)

Approx. 0.7kg (Excluding mounting fixtures)

Version1.37P or later

3 - 2

3. SPECIFICATIONS

3.2 Performance Specifications

*1

*2

*3

*4

*5

*6

*7

Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as the liquid crystal display comprises of a great number of display elements. Flickers may be observed depending on the display color.

Please note that these dots appear due to its characteristic and are not caused by product defect.

Flickers and partial discoloration may be generated on the liquid crystal display panel due to the display contents or the contrast adjustment. However, please note that these phenomena appear due to its characteristic and are not caused by product defect.

There is a difference in the display brightness and the color tones between liquid crystal display panels. When using multiple liquid crystal display panels, please note that there is an individual difference between them.

A crosstalk (shadow as an extension of the display) may appear on the liquid crystal display panel. Please note that it appears due to its characteristic.

When the display section is seen from the outside of the display angle, the display color seems like it has changed. Please note that it appears due to its characteristic. Especially, the response time of a STN liquid crystal display is slower in the lower temperature due to its characteristic. Please use the display after checking the response time.

Please note that the response time, brightness and color of the liquid crystal display panel may vary depending on the usage environmental temperature.

When the same screen is displayed for a long time, an incidental color or partial discoloration is generated on the screen due to heat damage, and it may not disappear.

To prevent the heat damage, the screen saver function is effective.

For details on the screen saver function, refer to the following.

11.1 Display Setting

Gradation inversion is a characteristic of liquid crystal display panel. Please be forewarned that depending on the displayed color, the visualization may be difficult even within the described view angle.

The GOT screen saving/backlight off function prevents images from becoming permanently etched on the display screen and increases the backlight life.

11.1 Display Setting

The touch panel is analog resistive film-type. If you touch the panel simultaneously in 2 points or more, the switch that is located around the center of the touched point, if any, may operate. Do not touch the panel in 2 points or more simultaneously.

Do not press the GOT display section with a pointed material as a pen or driver. Doing so can result in a damage or failure of the display section.

An analog resistive film-type touch panel does not require adjustment usually. However, misalignment between object position and actual touched position may be caused as usage time passes. If misalignment between object position and actual touched position may occur, adjust the touch panel position. Misalignment between object position and actual touched position may operate an unintended object, which causes unintended operation by mis-output and mis-operation.

ROM in which new data can be written without deleting the written data

Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.

Note that this does not guarantee all user's operation environment. The protection is not applied when the interface environment protection cover is removed.

In addition, the product may not be used in environments under exposition of oil or chemicals for a long period of time, or in environments filled with oil-mist.

3.3 Power Supply Specifications

Item

Input power supply voltage

Fuse (built-in, irreplaceable)

Power consumption

At backlight off

Inrush current

Permissible instantaneous power failure time

Noise immunity

Dielectric withstand voltage

GT1450-QLBD GT1450-QLBDE

24VDC (+10% -15%), ripple voltage 200mV or less

Specifications

GT1455-QTBD

1.6A

7.68W (320mA/24V)

6.72W (280mA/24V)

30A or less (26.4VDC) 2ms

Within 5ms

8.40W (350mA/24V)

7.44W (310mA/24V)

7.68W (320mA/24V)

6.72W (280mA/24V)

GT1455-QTBDE

8.40W (350mA/24V)

7.44W (310mA/24V)

Noise voltage: 1000Vp-p, Noise width: 1µs (by noise simulator of 30 to 100Hz noise frequency)

500VAC for 1 minute (across power supply terminals and earth)

Insulation resistance

10M or larger by insulation resistance tester (across power supply terminals and earth)

Applicable wire size

0.75[mm

2

] or more for power supply, 2[mm

2

] or more for grounding

Applicable solderless terminal Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A

1

2

3

4

5

6

7

8

Operation at momentary power failure

The GOT continues to operate even upon 5ms or shorter instantaneous power failure.

The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes operation as soon as the power is restored.

3. SPECIFICATIONS

3.3 Power Supply Specifications

3 - 3

3 - 4

3. SPECIFICATIONS

3.3 Power Supply Specifications

4.

PARTS NAME

4.1 Front Panel

(4)

(1)(2)

(3)

(5)(6)

No.

(1)

(2)

(3)

(4)

(5)

(6)

Display section

Touch panel

POWER LED

Name

Logo label

USB interface

USB environmental protection cover

Description

Displays the utility screen and the user creation screen.

For touch switch operation on the utility screen and the user creation screen

Lit in green: Power is correctly supplied.

Lit in orange: Screen saving.

Blinks in orange/green: Blown back light bulb

Not lit: Power is not supplied.

Removable

USB interface for communicating with PC (Device)

For OS installation, project data download, and FA transparent

Opens/closes when the USB interface is used.

4. PARTS NAME

4.1 Front Panel

4 - 1

5

6

7

3

4

1

2

8

4.2 Back Panel

(1) (4) (5) (7) (8)

(6)

(2)

(13)

Battery cover opened

(14)

(9)

Power supply terminal layout

(12) (3) (10) (15)

(11)

No.

(1)

(5)

(6)

(7)

(2)

(3)

(4)

(9)

(10)

(11)

(12)

(13)

(14)

(8)

(15)

Name

RS-232 interface

RS-422/485 interface

USB interface

Preventive hole from removing for the USB cable

Rating plate (nameplate)

SD card interface

SD card access LED

SD card access switch

Battery

Battery cover

Power terminal

Power terminal cover

Reset switch

Terminating resistor selector switch

Ethernet communication status

LED

Description

For communicating with controller (PLC, microcomputer board, bar code reader, RFID, etc) or PC (OS installation, project data download, transparent) (D-sub 9pin male)

For communicating with controller (PLC, microcomputer board, etc) (D-sub 9pin female)

USB interface for data transfer, data storage (host)

Hole fixed with banding band or others as a prevention from removing for the USB cable

The model name, current consumption, product number, H/W version, and BootOS version are described.

Interface for installing the SD card to the GOT

Lit: SD card being accessed, Not lit: SD card is not accessed.

Prohibits accessing the SD card removing the card from the GOT.

ON: SD card being accessed (SD card removal prohibited)

OFF: SD card not accessed (SD card removal possible)

GT11-50BAT battery for storing clock data, alarm history, recipe data, time action setting value, advanced alarm, advanced recipe, logging, hard copy and SRAM user area

Opens/closes when the battery is replaced or the terminating resistor is selected.

Power terminal and FG terminal (for power supply (24VDC) to GOT and grounding)

Opens/closes when the power terminal is connected. (color: transparent)

Switch for resetting the hardware (Use an isolated rod to operate.)

For switching the RS-422/485 communication interface terminating resistor

SD RD: Turns on in green during data communication,

100M: Turns on in green during 100Mbps transmission.

4 - 2

4. PARTS NAME

4.2 Back Panel

4.3 Rear Face

1

2

(2) (1) (2)

No.

(1)

(2)

Name

Ethernet interface

Holes for unit mounting fixtures

Description

For Ethernet connection to a controller (PLC microcomputer board) (RJ-45 connector)

Holes for the mounting fixtures (accessory) when the GOT is mounted to the panel (4 holes at top and bottom)

3

4

5

6

7

8

4. PARTS NAME

4.3 Rear Face

4 - 3

4 - 4

4. PARTS NAME

4.3 Rear Face

5.

UL, cUL STANDARDS AND EMC DIRECTIVE

1

5.1 UL, cUL Standards

UL, cUL Standard are recognized in use by the following combination (Model and Hardware version of the GOT/LOT.).

GOT

Item

RS-232/485 signal conversion adapter

Model

GT1455-QTBD

GT1455-QTBDE

GT1450-QLBD

GT1450-QLBDE

GT14-RS2T4-9P

Hardware version of the GOT/LOT.

Version C or later

LOT.121 or later

2

3

Checking method of hard ware version.

Confirm the hardware version with the rating plate of the GOT.

GRAPHIC OPERATION TERMINAL

MODEL

GT1455-QTBDE

IN 20. 4 26. 4VDC POWER 8.40W MAX

S/N

1217999 CQ G

MAC. ADD. 0026926212C6

MITSUBISHI ELECTRIC COPORATION

MADE IN JAPAN JY550D26101C

CQ

Hardware version

4

„

General notes on Power supply

This equipment must be supplied by a UL Listed or Recognized 24V DC rated power supply and UL Listed or

Recognized fuse rated not higher than 4A, or a UL Listed Class 2 power supply.

5.2 EMC Directive

For the products sold in European countries, the conformance to the EMC Directive, which is one of the European

Directives, has been a legal obligation since 1996. Also, conformance to the Low Voltage.

Directive, another European Directives, has been a legal obligation since 1997.

Manufacturers who recognize their products must conform to the EMC and Low Voltage Directive are required to declare that their products conform to these Directives and put a "CE mark" on their products.

• This product is designed for use in industrial applications.

• Manufactured by: Mitsubishi Electric Corporation

2-7-3 Marunouchi, Chiyoda-ku, Tokyo 100-8310 Japan

• Manufactured at: Mitsubishi Electric Corporation Himeji Works

840 Chiyoda-machi, Himeji, Hyogo 670-8677 Japan

• Manufactured at: Mitsubishi Electric Corporation Nagoya Works

1-14 Yada-minami 5-Chome, Higashi-ku, Nagoya 461-0048 Japan

• Authorized Representative in the European Community: Mitsubishi Electric Europe B.V.

Gothaer Str. 8, 40880 Ratingen, Germany.

5

6

7

8

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.1 UL, cUL Standards

5 - 1

5.2.1

Requirements to Meet EMC Directive

EMC Directives are those which require "any strong electromagnetic force is not output to the external.:Emission

(electromagnetic interference)" and "It is not influenced by the electromagnetic wave from the external.: Immunity

(electromagnetic sensitivity)".

Items „ EMC directive thru „ Grounding summarize the precautions to use GOT and configure the mechanical unit in

order to match the EMC directives.

Though the data described herein are produced with our best on the basis of the requirement items and standards of the restrictions gathered by Mitsubishi, they do not completely guaranteed that all mechanical unit manufactured according to the data do not always match the above directives. The manufacturer itself which manufactures the mechanical unit must finally judge the method and others to match the EMC directives.

„

EMC directive

The standards of the EMC Directive are shown below.

Applied standard Test standard Test details

EN61131-2

: 2007

EN55011

Radiated noise

EN61000-4-2

EN61000-4-3

Radiated field AM modulation

*1

*1

Electrostatic immunity

*1

EN61000-4-4

Fast transient burst noise

*1

Electromagnetic emissions from the product are measured.

Immunity test in which static electricity is applied to the cabinet of the equipment.

Immunity test in which field is irradiated to the product.

Immunity test in which burst noise is applied to the power line and signal lines.

Standard value

30M-230MHz QP:

30dB V/m (30m in measurement range)

*2, *3

230M-1000MHz QP:

37dB V/m(30m in measurement range)

*2, *3

4kV Contact discharge

8kV Aerial discharge

80-1000MHz:10V/m

1.4-2GHz:3V/m

2.0-2.7GHz:1V/m

80%AM modulation@1kHz

Power line:2kV

Digital I/O(24V or higher): 1kV

(Digital I/O(24V or less))> 250V

(Analog I/O, signal lines)> 250V

EN61000-4-5

Surge immunity

*1

EN61000-4-6

Conducted RF immunity

*1

EN61000-4-8

Power supply frequency magnetic field immunity

Immunity test in which lightening surge is applied to the product.

Power line (between line and ground): 0.5kV

Power line (between lines): 0.5kV

Data communication port: 1kV

Immunity test in which a noise inducted on the power and signal lines is applied.

Power line: 10V

Data communication port: 10V

Test for checking normal operations under the circumstance exposed to the ferromagnetic field noise of the power supply frequency (50/60Hz).

30 A/m

*1 The GOT is an open type device (device installed to another device) and must be installed in a conductive control panel.

The above test items are conducted in the condition where the GOT is installed on the conductive control panel and combined with the Mitsubishi PLC.

*2 QP: Quasi-peak value, Mean : Average value

*3 The above test items are conducted in the following conditions.

30M-230MHz QP : 40dB V/m (10m in measurement range)

230M-1000MHz QP : 47dB V/m (10m in measurement range)

5 - 2

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.2 EMC Directive

„

Control panel

GOT is an open type device (device installed to another device) and must be installed in a conductive control panel.

It not only assure the safety but also has a large effect to shut down the noise generated from GOT, on the control panel.

(1) Control panel

(a) The control panel must be conductive.

(b) When fixing a top or bottom plate of the control panel with bolts, do not coat the plate and bolt surfaces so that they will come into contact.

And connect the door and box using a thick grounding cable in order to ensure the low impedance under high frequency.

(c) When using an inner plate to ensure electric conductivity with the control panel, do not coat the fixing bolt area of the inner plate and control panel to ensure conductivity in the largest area as possible.

(d) Ground the control panel using a thick grounding cable in order to ensure the low impedance under high frequency.

(e) Holes made in the control cabinet must be 10 cm (3.94inch) diameter or less. If the holes are 10cm

(3.94inch) or larger, radio frequency noise may be emitted.

In addition, because radio waves leak through a clearance between the control panel door and the main unit, reduce the clearance as much as practicable.

The leakage of radio waves can be suppressed by the direct application of an EMI gasket on the paint surface.

(2) Connection of power and ground wires

Ground and power supply wires for the GOT must be connected as described below.

Provide a grounding point near the GOT. Short-circuit the FG terminals of the GOT (FG: frame ground) and ground them with the thickest and shortest wire possible (The wire length must be 30cm (11.81in.) or shorter.)

The FG terminals function is to pass the noise generated in the PC system to the ground, so an impedance that is as low as possible must be ensured. As the wires are used to relieve the noise, the wire itself carries a large noise content and thus short wiring means that the wire is prevented from acting as an antenna.

Note) A long conductor will become a more efficient antenna at high frequency.

(3) Shock protection

In order to prevent those who are unfamiliar with power facility, e.g., an operator, from getting a shock, make sure to take the following measures on the control panel.

(a) Store the GOT within the control panel locked, and allow only those who are familiar with power facility to unlock the panel.

(b) Build the structure in order that the power supply will be shut off when the control panel is opened.

(4) Dustproof and waterproof features

The control panel also provides protection from dust, water and other substances. Insufficient ingression protection may lower the insulation withstand voltage, resulting in insulation destruction. The insulation in the

GOT is designed to cope with the pollution level 2, so use in an environment with pollustion level 2 or better.

Pollution level1 :

Pollution level2 :

Pollution level3 :

An environment where the air is dry and conductive dust does not exist.

An environment where conductive dust does not usually exist, but occasional temporary conductivity occurs due to the accumulated dust.

Generally, this is the level for inside the control panel equivalent a control room or on the floor of a typical factory.

An environment where conductive dust exits and conductivity may be generated due to the accumulated dust.

An environment for a typical factory floor.

Continuous conductivity may occur due to rain, snow, etc. An outdoor environment.

Pollution level4 :

„

Grounding

The following are applicable ground terminals. Use them in the grounded state.

Be sure to ground the GOT for ensuring the safety and complying with the EMC Directive.

Protective grounding

Functional grounding

:

:

Ensures the safety of the GOT and improves the noise resistance.

Improves the noise resistance.

1

2

3

4

5

6

7

8

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.2 EMC Directive

5 - 3

5.2.2

EMC Directive-Compliant System Configuration

For information of the EMC Directive-compliant models please consult with your nearest Mitsubishi product provider.

„

GOT

Use any of the following GOTs with which CE mark logo is printed on the rating plate.

When using a GOT other than shown below, the system does not conform to the EMC Directive.

Item Hardware version of the GOT

GT1455-Q

GT1450-Q

Model

GT1455-QTBD

GT1455-QTBDE

GT1450-QLBD

GT1450-QLBDE

Version C or later

Version C or later

Checking method of hard ware version.

Confirm the hardware version with the rating plate of the GOT.

GRAPHIC OPERATION TERMINAL

MODEL

GT1455-QTBDE

IN 20. 4 26. 4VDC POWER 8.40W MAX

S/N 11Y0086 BQ G

MAC. ADD. 002692621123

MITSUBISHI ELECTRIC COPORATION

MADE IN JAPAN JY550D26001C

BQ

Hardware version

„

Connection method

Use the following methods to connect with the GOT to ensure compliance with the EMC Directive.

: Compliant with EMC Directive : Not compliant with EMC Directive

Connection method

*1

GT14

Direct connection to CPU

Computer link connection

CC-Link connection (via G4)

Ethernet connection

GOT multi-drop connection

Other connections

*1

*1 When connecting the GOT to other controllers as a PLC manufactured by other company, create the cable (by the user) and configure the system to meet the EMC Directive specifications for the connected device.

Connected devices

If connecting to the PLC or microcomputer other than Mitsubishi products

(MELSEC-Q series, MELSEC-L series, MELSEC-QnA , MELSEC-A series or MELSEC-FX series) please refer to the EMC Directive compliance manual for that specific device.

5 - 4

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.2 EMC Directive

„

About the cable used

Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise.

Therefore, when installing any communication cables care should always be taken with the routing and location of those cables. The GOT identified on the previous page are compliant with the EMC requirement when the following communication cables are used.

(1) Panel-mounted USB port extension

GT14-C10EXUSB-4S

(2) Direct connection cable

Existing Cables User Made Cables

GT01-C30R2-6P, GT01-C30R4-25P,

GT01-C100R4-25P, GT01-C200R4-25P,

GT01-C300R4-25P, GT01-C10R4-8P,

GT01-C30R4-8P, GT01-C100R4-8P,

GT01-C200R4-8P, GT01-C300R4-8P,

GT01-C30R2-9S, GT01-C30R2-25P,

WS0-C20R2

(3) Ethernet connection cable

Shielded twisted pair cable (STP)

The cable need to be independently tested by the user to demonstrate EMC compatibility when they are used with the GOT, the PLC of MELSEC-Q series,

MELSEC-L series, MELSEC-QnA, MELSEC-A series and MELSEC-FX series.

(4) PLC (manufactured by other company), microcomputer, temperature controller, inverter, servo amplifier,

CNC, MODBUS(R)/RTU or MODBUS(R)/TCP connection

Produce the cable (RS-232 cable, RS-422 / 485 cable) for connecting the GOT to a controller with reference to the following manual.

GOT1000 Series Connection Manual for GT Works3 and a controller used

1

2

3

4

5.2.3

Precautions for Wiring/Connecting the EMC Directive-Compliant Product

Wire and connect GOT1000 series equipments as instructed below. If the GOT1000 series equipments are configured in a way different from the following instructions, the system may not comply with EMC directives.

„

Power and ground wires wiring method

(1) Power and ground wires wiring method

Connect the power wire and connection cable as shown in the illustration, and be sure to attach a ferrite core

(TDK Corporation type ZCAT3035-1330 or similar) within the range shown below.

Lead the power wire and ground wire as shown in 5.2.1 „ Control panel (2).

Be sure to ground the FG cable, and protective ground cable.

5

6

7

Up to 75mm

8

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.2 EMC Directive

5 - 5

Any device which utilizes a data communication function is susceptible to the wider effects of local EMC noise.

Therefore, when installing any communication cables care should always be taken with the routing and location of those cables.

Optional ferrite cores are recommended when the cable route is close to EMC noise sources like welders, large motors, etc.

All tests have been performed with original Mitsubishi cables. For customer prepared cables, please refer to the previous page.

Existing Cables User Made Cables GOT Unit

GT1450-QLBD

GT1450-QLBDE

GT1455-QTBD

GT1455-QTBDE

Ex. GT01-C30R4-8P (as shown in EX.1)

3 rd

party cables need to be independently tested by the user to demonstrate EMC compliance.

Example 1

(250mm)

(9.84inch)

GT01-C30R4-8P

F = Ferrite core

Ex. NEC TOKIN - ESD-R-17S or similar

100mm

(3.93inch)

Programmable controller

F F F

GOT units

140mm

(5.51inch)

Comes equipped

Optional Optional

5 - 6

5. UL, cUL STANDARDS AND EMC DIRECTIVE

5.2 EMC Directive

6.

INSTALLATION

MOUNTING PRECAUTIONS

DANGER

• Be sure to shut off all phases of the external power supply used by the system before mounting or removing the

GOT to/from the panel.

Not doing so can cause the unit to fail or malfunction.

MOUNTING PRECAUTIONS

CAUTION

• Use the GOT in the environment that satisfies the general specifications described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

• Never drop cutting chips and electric wire chips into the ventilation window of the GOT when you drill screw holes or perform wiring.

Otherwise, fire, failure or malfunction may be caused.

• Connect connection cables securely to the specified connectors while the power is turned OFF.

Imperfect connection may cause malfunction or failure.

• Operate and store the GOT in environments without direct sunlight, dust, lamp black, conductive dust, corrosive gas, combustible gas, high temperature, condensation, wind, rain, vibrations and impacts.

Electric shock, fire, malfunction, product damage or deterioration can be caused.

• Tighten the mounting screws within the specified torque range.

Undertightening can cause the GOT to drop, short circuit or malfunction. Also, undertightening can disable waterproof or oil proof effect.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the GOT. Also,

"distortion" of the GOT or the panel may disable waterproof or oil proof effect.

6.1 Control Panel Inside Dimensions for Mounting GOT

Mount the GOT onto the control panel while considering the following control panel inside dimensions.

Vertical installation of the GOT requires a space with the same dimensions as the horizontal installation turned 90 degrees clockwise (seen from the display side).

2

3

4

5

6

Applicable cable

Some cables may need to be longer than the specified dimensions when connecting to the GOT. Therefore, consider the connector dimensions and bending radius of the cable as well for installation.

30 (1.19") 152 (5.99")

7

1

Unit: mm (inch)

6. INSTALLATION

6.1 Control Panel Inside Dimensions for Mounting GOT

6 - 1

8

6.2 Panel Cutting Dimension

Make holes in the panel according to the dimensions list below.

Also, ensure 10mm of space in upper and lower parts of the panel for mounting fixtures.

• Horizontal format (If the vertical format is selected, the dimension must be rotated 90 degrees.)

153

+2

-0

(6.03" )

10 (0.4") or more

Within 2 (0.08”) to 4 (0.16”)

10 (0.4") or more

Unit: mm (inch)

6.3 Mounting Position

When mounting the GOT, the following clearances must be maintained from other structures and devices.

• The below diagram represents a horizontal installation. (The same clearances must be maintained when rotating the

GOT 90 degrees clockwise for a vertical installation.)

Installation Environment

In the presence of radiated-noise or heat-generating equipment nearby

In the absence of radiated-noise or heat-generating equipment nearby

*1 Vertical Format....50 mm (1.97") or more

*2 Vertical Format....80 mm (3.14") or more

A, D

50mm or more

20mm or more

B

80mm or more

*1

20mm or more

C

50mm or more

*2

20mm or more

E

100mm or more

20mm or more

C D

E

Panel thickness: 2 to 4mm

(0.08 to 0.16inch)

6 - 2

6. INSTALLATION

6.2 Panel Cutting Dimension

6.4 Control Panel Temperature and Mounting Angle

When mounting the main unit to a control panel or similar fixture, set the GOT display section as shown below.

„

Horizontal installation

When the temperature inside the control panel is 40 to 55 , the mounting angle should be in the range from 60 to

105 degrees.

GOT back panel

60°

105°

GOT display section

Control panel, etc.

The GOT will have a longer lifetime if used within the mounting angles shown above.

Ideally, the temperature inside the control panel should not exceed 0 to 40 .

„

Vertical installation

When the temperature inside the control panel is 40 to 50 , the mounting angle should be in the range from 60 to

105 degrees.

GOT back panel

60°

105°

GOT display section

Control panel, etc.

The GOT will have a longer lifetime if used within the mounting angles shown above.

Ideally, the temperature inside the control panel should not exceed 0 to 40 .

1

2

3

4

5

6

7

8

6. INSTALLATION

6.4 Control Panel Temperature and Mounting Angle

6 - 3

6.5 Installation Procedure

The GOT is designed to be embedded into a panel. Mount the GOT by following the procedure below.

For the panel cutting dimension, refer to "6.2 Panel Cutting Dimension".

Also, be sure that the thickness of the mounting panel face is 2 to 4mm.

Packing

Magnified illustration

1.

Installing the packing

Install packing to the packing installation groove on the back panel of the GOT.

While referring to the cross sectional view of the packing shown left, push the thinner side into the packing groove.

(Left drawing is the example of lateral format.)

Packing

Packing installation groove

Packing cross sectional view

Inserting direction

2.

Inserting into the panel face

Insert the GOT from the front side of the panel.

Mounting hole

Enlarged view

3.

Fixing the GOT

Engage the hook of the mounting fixture (accessory) to the unit fixing hole of the GOT and fix them by tightening the mounting screws in the torque range of 0.3 to 0.5N·m.

Mounting bracket

Mounting screw

4.

A protection film is attached on the display section of GOT prior to shipment.

Remove the film when the installation is completed.

6 - 4

6. INSTALLATION

6.5 Installation Procedure

1

Cautions on installation

(1) Tightening the mounting screw

Tighten the mounting screws within the specified torque range.

Undertightening can cause a drop and disable waterproof or oil proof effect.

Overtightening may damage the unit, or distort the panel and make a surface waviness on the display area, leading to deterioration of the visibility or incorrect input from the touch panel. Also, overtightening can disable waterproof or oil proof effect.

• Specified torque range: 0.3 to 0.5N·m

2

3

(2) Mounting panel face

Make sure that the panel surface is free from warpage, flaws and irregularities. Warpage, flaws and irregularities may disable the waterproof effect.

Select proper panel thickness under consideration of the panel strength.

(For example, the panel strength may be insufficient depending on the panel material and dimensions even if the panel thickness is acceptable. Insufficient panel strength may cause warpage depending on the installation positions of the GOT and other equipment.)

4

5

6

7

8

6. INSTALLATION

6.5 Installation Procedure

6 - 5

6 - 6

6. INSTALLATION

6.5 Installation Procedure

7.

WIRING

WIRING PRECAUTIONS

DANGER

• Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

• Please make sure to ground FG terminal of the GOT power supply section by applying 100 or less which is used exclusively for the GOT.

Not doing so may cause an electric shock or malfunction.

• Correctly wire the GOT power supply section after confirming the rated voltage and terminal arrangement of the product.

Not doing so can cause a fire or failure.

• Tighten the terminal screws of the GOT power supply section in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or the GOT.

• Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.

Not doing so can cause a fire, failure or malfunction.

2

3

WIRING PRECAUTIONS

CAUTION

• Plug the communication cable into the connector of the connected unit and tighten the mounting and terminal screws in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

This chapter describes the wiring to the GOT power supply section.

For the connection with a PLC, refer to the following.

GOT1000 Series Connection Manual for GT Works3

For the dimensional drawing of connection cables, refer to the following.

Appendix.1 External Dimensions

4

5

6

General preventive measures against noise

There are two kinds of noises: Radiated noise that is transmitted into the air and Conductive noise that is directly transmitted along connected lines.

Countermeasures must be taken considering both kinds of noises and referring to the following 3 points.

(1) Protecting against noise

(a) Keep signal lines away from noise sources such as a power cable or a highpower drive circuit.

(b) Shield the signal lines.

(2) Reducing generated noise

(a) Use a noise filter, etc. to reduce the level of the noise generated due to a source such as a high-power motor drive circuit.

(b) Attach surge killers to the terminals on the No Fuse Breaker (NFB), electromagnetic contactors, relays, solenoid valves, and generators to suppress noise interference.

(3) Releasing noise to the ground

(a) Make sure to connect the ground cable to the ground.

(b) Use a short and thick cable to lower its impedance.

(c) Ground the power system and the control system separately.

7

8

7. WIRING

7 - 1

1

7.1 Power Supply Wiring

7.1.1

Wiring example

Connect the power supply to the power terminals on the back panel of the GOT.

Use 0.75mm

2 or thicker cables to avoid voltage drop and tighten the terminal screw with the specified torque securely.

PC and external device connection cables

Grounding

(100 or less)

+

-

24VDC power supply

7.1.2

Grounding the GOT

„

About grounding

Make sure to carry out the following for grounding.

• Carry out the independent grounding if possible.

Apply the class D grounding. (Keep the grounding resistance within 100 or less.)

• If the independent grounding is impossible, carry out the shared grounding as shown in fig.2) below.

GOT

Other device

Grounding

(100 or less)

GOT

Other device

Grounding

(100 or less)

GOT

Other device

(1) Independent ground

...... Best condition

(2) Shared grounding

...... Good condition

(3) Common grounding

...... Not allowed

• Use the cable of 2mm

2

or more for grounding.

Set the grounding point closer to the GOT to make the grounding cable short as possible.

7 - 2

7. WIRING

7.1 Power Supply Wiring

„

Recommended terminal shape

Terminal screws should be tightened to between 0.5 to 0.8N·m. Terminal screws must be secured to prevent a loose connection thus avoiding a malfunction.

Do not tighten the terminal screw with a torque exceeding the specified torque. Failure to do so may cause equipment failures or malfunctions.

3.2

Terminal screw

Solderless terminal

6.2mm

or less

Terminal screw

Solderless terminal

3.2

6.2mm

or less

Cable size

Solderless terminal

Tightening torque

When wiring one cable to one terminal

When wiring two cables to one terminal

For power supply: 0.75mm

2

or more For grounding: 2mm

2

or more

M3 solderless terminal (applicable solderless terminal: RAV1.25-3, V2-N3A, FV2-N3A)

0.5 to 0.8N·m

7.1.3

The cause of malfunctions related wiring/Remedy

Grounding of the GOT may cause electric potential difference and noise interference, which may result in GOT malfunctions. These problems may be resolved by taking the following measures.

„

Wiring path of the GOT's ground cable and power line

Bundling the GOT's ground cable and power line together can cause interference noise, which may result in malfunctions.

Keeping the GOT's ground cable and power line away from each other will help minimize noise interference.

1

2

3

4

5

FG

FG

Good : Wiring the ground cable away from the

power cable

Power supply for power equipment

Power supply for power equipment

Bad : Bundling the ground cable and

the power cable

6

7

8

7. WIRING

7.1 Power Supply Wiring

7 - 3

7 - 4

„

Connecting the ground cable from the panel that houses control equipment to the panel to which the GOT is grounded

When running a single ground cable from the panel that houses such piece of control equipment as a PLC to the panel to which the GOT is grounded, the ground cable may have to be directly connected to the terminal on the GOT.

Connection cable

FG

Ground cable from the panel that houses control equipment

If electric potential difference between the ground points created by it causes malfunctions, lowering the voltage as shown in Remedy 1 below may solve the problem.

• Remedy 1 (Refer to the figures Remedy 1-1 and 1-2 below.)

If the electric potential difference between the ground cable and the panel that houses the GOT is creating problems, connect the ground cable to the panel also.

If the wiring method as shown in Remedy 1-1 is not feasible, follow Remedy 1-2.

Connection cable

Ground cable from the panel that houses control equipment

Use the thickest cable possible.

FG

Connection cable

Ground cable from the panel that houses control equipment

Use the thickest cable possible.

FG

Panel grounding

Panel grounding

Remedy 1-1 Remedy 1-2

If taking Remedy 1 worsens noise interference, taking Remedy 2 may alleviate it.

• Remedy 2 (Refer to the figures Remedy 2-1 and 2-2 below.)

Attach a ferrite core to the cable if noise from the GOT panel has adverse effects on the GOT when Remedy 1 is taken.

Wind the wire around the ferrite core several times (approx. 3 times), if a ferrite core is used.

If the wiring method as shown in Remedy 2-1 is not feasible, follow Remedy 2-2.

Connection cable

Ground cable from the panel that houses control equipment

Use the thickest cable possible.

Ferrite core

Remedy 2-1

FG

Panel grounding

Connection cable

Ground cable from the panel that houses control equipment

Use the thickest cable possible.

Ferrite core

Remedy 2-2

FG

Panel grounding

7. WIRING

7.1 Power Supply Wiring

7.2 Wiring inside and outside the panel

7.2.1

Wiring inside

Run power lines, servo amplifier drive wires, and communication cables so that they do not cross each other.

Noise interference that is generated by cables that cross each other may cause malfunctions.

Surge suppressors are an effective way to filter out surge noise that is generated from no fuse breakers (NFB), electromagnetic contactors (MC), relays (RA), solenoid valves, and induction motors.

For surge killers, refer to the section to follow.

7.2.3 Attaching surge killers to control equipment

Uncrossed power lines and communication cables

Crossing power lines and communication cables

Power cable

Power cable

NFB

PLC

GOT connection cable

NFB

PLC GOT connection cable

PLC I/O wire

PLC I/O wire

1

2

3

MC MC RA

Drive control wire

Terminal block

RA

MC MC RA

Drive control wire

Terminal block

RA

4

7.2.2

Outside the panel

To pull the power line and communication cable out of the panel, make two pullout holes away from each other and pull the cables through.

Putting both cables through the same pullout hole will increase noise interference.

Power line

Power line

Connection cable

Connection cable

Pullout hole Pullout hole

Keep the power line and communication cable inside the duct at least 100mm away from each other.

If that is not possible, the use of a metal separator inside the duct can reduce noise interference.

Power line

Wiring duct

Separator

100mm or more

Signal line

Power line Signal line

5

6

7

8

7. WIRING

7.2 Wiring inside and outside the panel

7 - 5

7.2.3

Attaching surge killers to control equipment

If communication errors happen in synch with the on/off signals from certain control equipment (referred to as "load" hereafter) such as no fuse breakers, electromagnetic contactors, relays, solenoid valves, and induction motors, surge noise interference is suspected.

If this problem happens, keep the ground cable and communication cable away from the load.

If that is not possible, an installation of a surge killer will help reduce noise interference.

Place the surge killer as close to the load as possible.

Remedy for AC inductive load

Keep the ground cable and communication cable away from each other.

Output

C

R

L:Load

AC

Output equipment such as PLC output unit

Remedy for DC inductive load

Keep the ground cable and communication cable away from each other.

Place the surge killer near the load.

Output

D

L:Load

DC

Place the surge killer near the load.

Output equipment such as PLC output unit

7 - 6

7. WIRING

7.2 Wiring inside and outside the panel

8.

OPTION

8.1 SD Card

The SD card is used to transmit the OS or project data and to save the data of the alarm history function.

For details, refer to the following.

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

8.1.1

Applicable SD card

The following SD cards are applicable for GOT.

Model name

L1MEM-2GBSD

L1MEM-4GBSD

-

*1

SD memory card 2GB

SDHC memory card 4GB

Description

Commercially-available SD card

*1

Some models with the operations checked by our company are usable.

For the operation-checked models, refer to "Operation Check Results of Third Party SD Cards on GT14 Model" (Hime-T-P-0089) separately available.

The Technical News above is available as a reference at the Information site for Mitsubishi industrial automation products

MELFANSweb home page.

(MELFANSweb home page: http://wwwf2.mitsubishielectric.co.jp/melfansweb/english/index_e.htm)

2

3

4

8.1.2

Installing and removing procedures of the SD card

Install/remove the SD card with the power supply of GOT is OFF or SD card access switch is "OFF".

„

Installing

1.

Set the SD card access switch of the GOT to "OFF", and make sure that the SD card access LED turns off.

When the SD card access LED turns off, the SD card can be installed even during the GOT power on.

5

6

1

SD card front face

7

2.

Insert the SD card into the SD card interface with its front side (nameplate side) outside.

3.

Turn the SD card access switch on.

After the SD card access switch is turned on, the SD card can be used.

8

8. OPTION

8.1 SD Card

8 - 1

„

Removing

1.

Set the SD card access switch of the GOT to "OFF."

Make sure that the SD card access LED turns off.

When the SD card access LED turns off, the SD card can be installed or removed even during the GOT power on.

2.

Push-in the SD card once and leave your finger, then remove the SD card.

Precautions for removing the SD card

(1) While the SD card access LED is on, do not install/remove the SD card or power off the GOT.

To do so may cause data corruption or malfunction.

(2) When ejecting the SD card, support it by hand since it may pop out.

Failure to do so may cause a fall of the SD card leading to failure or damage of the card.

8 - 2

8. OPTION

8.1 SD Card

8.2 USB Memory

The USB memory is used to transmit the OS or project data and to save the data of the alarm history function.

For details, refer to the following.

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

8.2.1

Applicable USB memory

The following USB memory is applicable for GOT.

-

Model name

*1

Description

Commercially-available USB memory

*1

Some models with the operations checked by our company are usable.

For the operation-checked models, refer to "List of valid devices applicable for GOT1000 series" (T10-0039) separately available.

The Technical News above is available as a reference at the Information site for Mitsubishi industrial automation products

MELFANSweb home page.

(MELFANSweb home page: http://wwwf2.mitsubishielectric.co.jp/melfansweb/english/index_e.htm)

8.2.2

Installing and removing procedures of the USB memory

When USB memory is accurately inserted to the USB interface, the GOT automatically recognizes it.

For removing methods of the USB memory, refer to the following.

13.2.9 USB device status display

1

2

3

4

5

6

7

8

8. OPTION

8.2 USB Memory

8 - 3

8.3 Battery

The battery backs up clock data and data stored in the built-in RAM (D drive) including alarm history, recipe data, time action setting value, advanced alarm, advanced recipe, logging, hard copy, and SRAM user area. A battery is installed to

GT14 when GT14 is shipped from the factory.

8.3.1

Applicable battery

The following battery is applicable for GT14.

Model name

GT11-50BAT

Description

Battery for clock data, alarm history, recipe data, time action setting value, advanced alarm, advanced recipe, logging, hard copy, and SRAM user area backups

8.3.2

Battery specifications

The following describes the battery specifications.

Item

Model name

Type

Initial voltage

Life

Application

Specifications

GT11-50BAT

Manganese dioxide lithium primary battery

3.0V

Approx. 5 years (Operating ambient temperature of 25 )

For clock data, alarm history, recipe data, time action setting value, advanced alarm, advanced recipe, logging, hard copy, and SRAM user area backups

For the battery directive in EU member states, refer to the following.

17.4 ■Handling of Batteries and Devices with Built-in Batteries in EU Member States

Battery life and replacement time

(1) Battery life reference: Approx. 5 years (Operating ambient temperature of 25 )

Battery replacement time reference: 4 to 5 years

The battery is susceptible to natural discharge. Order one when necessary.

(2) Check if the battery condition is normal within the utility.

For details of battery status display, refer to the following.

11.1 Display Setting

8 - 4

8. OPTION

8.3 Battery

8.3.3

Battery replacement procedure

Replace battery periodically at intervals of 4 to 5 years as reference.

1.

Turn the GOT power off.

Battery cover

2.

Open the battery cover of the GOT.

3.

Remove the old battery from the GOT.

Connector

Connector

1

2

Battery cover

4.

Disconnect the old battery connector and insert the new battery connector within 30s.

5.

Install a new battery to the GOT and close the battery cover.

3

4

6.

Turn the GOT power on.

7.

Check if the battery condition is normal with the utility.

For details of battery status display, refer to the following.

12. CLOCK SETTINGS AND BATTERY

STATUS DISPLAY (TIME SETTING AND

DISPLAY)

5

6

7

8

8. OPTION

8.3 Battery

8 - 5

8.4 Protective Sheet

The protective sheet is used to protect the operation surface from damage or dirt when the touch key of GOT display section is operated.

For the GOT, the protective sheet is attached for transportation. (It is different from the one described in this chapter.)

8.4.1

Applicable protective sheet

Product name

Protective sheet

Model name

GT14-50PSCB

GT14-50PSCB

GT14-50PSCW

GT14-50PSGW

5.7" protective sheet

Description

Clear 5 sheets

Antiglare 5 sheets

Clear (Frame: white) 5 sheets

Antiglare (Frame: white) 5 sheets

8.4.2

Installing procedure

1.

If the protective sheet has been already attached to the

GOT, remove the old one from the GOT display section holding the lower right corner.

If the protective sheet for transportation is attached to the

GOT, remove it too.

2.

Remove the release paper from the back of a new protective sheet. Do not remove the protective film.

3.

Make sure to fit the sheet on the GOT without wrinkles or air between the sheet and the GOT.

4.

Remove the protective film from the protective sheet.

When the user continues using the GOT with the protective film, the film may not be removed.

8 - 6

Replacement time of protective sheet

Check the status of the protective sheet visually by the daily inspection.

The visibility becomes worse when there is too much dirt and cracks, causing malfunction. Proceed replacement promptly.

8. OPTION

8.4 Protective Sheet

8.5 Protective Cover for Oil

Use of the protective cover for oil improves waterproof property, oil resistance, and chemical resistance of the GOT.

8.5.1

Applicable protective cover for oil

The following protective cover for oil is applicable for GT14.

Product name

Protective cover for oil

Model name

GT05-50PCO 5.7" protective cover for oil

Description

8.5.2

Installing procedure

1

2

3

Before attaching protective cover for oil

A protective film is attached on the display area when the GOT is shipped. Make sure to remove the protective film before attaching the protective cover for oil.

For attaching the protective cover for oil to the GOT already mounted on the control panel, follow the procedures as below.

• Remove the GOT from the control panel.

Make sure to externally shut off all phases of the power supply and remove all cables from the GOT in advance.

• Clean dirt off surfaces of the GOT and control panel.

4

GOT

1.

Position the POWER LED frame of the cover to the

POWER LED on the GOT front face, and the direction of the cover is decided.

5

Protective Cover For oil

Please do not pull the oil cover more than the necessity, and do not bend it extremely.

The seat part and the rubber part in the display part might flake off.

Protective Cover For oil

2.

One corner of the cover is pulled outside, and it hangs it on the corner of the front panel of GOT.

6

7

The corner is hung.

GOT

8

8. OPTION

8.5 Protective Cover for Oil

8 - 7

The corner on the left is hung and the oil cover is hung from A side to D side on the starting point sequentially.

A

B

D

C

3.

The oil cover was hung and the edge of the oil cover is sequentially obtained and obtain the oil cover to cover rubber packing parts in the back of GOT of the front panel.

(From A side to D side, in the direction of the arrow)

Make sure that corners of protective cover for oil match those of GOT front.

Protectivecover for oil

Panel cut dimensions

Mounting metal fixture

Control panel

4.

Please confirm all surroundings. Check whether the rubber packing is fitted correctly into the groove on the under side of the GOT front panel, and then whether the protective cover for oil securely covers the rubber packing part to prevent invasion of liquids into the board.

5.

Mount the GOT onto the control panel. When the control panel is dirty, clean the control panel. The panel cutting dimensions and mounting screw tightening torque with the protective cover for oil are the same as those without the cover.

(1) Precautions on installation

Tighten the mounting screws within the specified torque range.

• Specified torque range (0.3 to 0.5N·m)

Undertightening can cause a drop. Also, undertightening can disable waterproof or oil proof effect.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the GOT or the mounting fixtures. Also, "distortion" of the GOT or the panel may disable waterproof or oil proof effect.

(2) Precautions for protective cover for oil

• The protective cover for oil is a consumable product.

Check the cover for scratch, damage or dirt at regular intervals, and replace with new one if necessary.

• Do not push the protective cover for oil with pointed tools, including mechanical pencils and screwdrivers.

Doing so causes scratches and damages of the cover.

• Do not clean the protective cover for oil with bleaches, thinners, organic solvents, corrosive chemicals, and others. Doing so causes changes in shape and color of the cover.

• When the protective cover for oil is attached to the GOT, do not stretch and bend the cover too much. Doing so may cause a separation between the sheet and rubber.

• Do not place or use the protective cover for oil in direct sunshine.

• When the protective cover for oil gets dusts, wipe the dusts off with a damp cloth.

• Do not do a frequent detaching the protective cover for oil.

It causes deterioration in the oil performance and the medicine performance.

• It is not the one to guarantee all customer's environments.

Moreover, it is not likely to be able to use it in the environment to which oil splashes for a long time and the environment with which Oilmist is filled.

8 - 8

8. OPTION

8.5 Protective Cover for Oil

8.6 USB Environmental Protection Cover

The USB environmental protection cover protects the USB connector on the front face of GOT from dust, water, and oil.

The GOT is installed with the USB environmental protection cover at factory shipment.

Replace when damage and deterioration are caused.

8.6.1

Applicable USB environmental protection cover

The following USB environmental protection cover is applicable for GT14.

Product name

USB environmental protection cover

Model name

GT14-50UCOV

Description

Environmental protection cover for USB interface on the main unit front panel (conforming to IP67f)

8.6.2

Installing procedure

Open

USB environmental protection cover

Mounting screw

1.

Turn the GOT power off.

2.

Disconnect the USB cable from the GOT if one is connected.

3.

Open the USB environmental protection cover equipped with the GOT and remove the mounting screws.

4.

Remove the old USB environmental protection cover from the GOT to replace it with the new USB environmental protection cover.

5.

Fix the projection of the new USB environmental protection cover to be fitted into the hole of the GOT, tighten the mounting screw in the specified torque range, then install it to the GOT.

Tighten the mounting screws in the specified torque range.

Not doing so may cause a damage or a drop.

Specified torque range: 0.2 to 0.3N·m

Mounting screw

M3 x 6 pan head screw

1

2

3

4

5

6

7

M3 x 6 pan head screw

Precautions when the USB environmental protection cover is opened

Environmental protective structure of USB interface is "IP2X" when the USB environmental protection cover is opened.

8. OPTION

8.6 USB Environmental Protection Cover

8 - 9

8

8.7 Stand

Stand is used to fix the GOT to standing status in order to debug the monitor screen data easily.

8.7.1

Applicable stand

The following stand is applicable for GT14.

Stand

Product name Model name

GT05-50STAND Stand for 5.7" (for GOT1000 series)

Description

8.7.2

Installing procedure

Adjust to

45 , 55 , 65 or 75 .

1.

Adjust the mounting angle of GOT with the angle adjusting fitting of the stand.

Angle adjusting fitting

GOT mounting face

2.

Put the GOT into the stand from the stand front side and fix it using the mounting fixtures.

For how to mount the GOT, refer to the following.

6.5 Installation Procedure

For a detail of the stand, refer to the following.

GOT1000 STAND User's Manual

8 - 10

8. OPTION

8.7 Stand

8.8 Connector Conversion Adapter

GT10-9PT5S type connector conversion adapter enables an easy crossover wiring for the multi-drop-connected GOTs.

For the wiring between the connector conversion adapter and the controller, refer to the following manual.

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

8.8.1

Applicable connector conversion adapter

The following connector conversion adapter is applicable.

Model name

GT10-9PT5S

Description

For GOT multi-drop connection

8.8.2

Installing procedure of connector conversion adapter

1.

Turn the GOT power off.

2.

Connect the connection conversion adapter to the RS-

422/485 interface on the GOT.

1

2

3

4

3.

Fix the connection conversion adapter to the GOT using the provided M3 tapping screws.

Tightening torque: 0.3 to 0.6 N•m

5

6

7

8

8. OPTION

8.8 Connector Conversion Adapter

8 - 11

8.9 Serial Multi-Drop Connection Unit

8.9.1

Serial multi-drop connection unit

GOT serial multi-drop connection is a communication method for 1:N communication by connecting multiple GOTs to one PLC, using the GT01-RS4-M serial multi-drop connection unit.

For details of GOT multidrop connection, refer to the following.

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

Serial multi-drop connection unit

Connect to the PLC

RS-485 cable

8.9.2

Applicable serial multi-drop connection unit

The following serial multi-drop connection unit is applicable.

Model name

GT01-RS4-M

Description

For GOT multi-drop connection

8.9.3

Installation

„

Installed with DIN rail

Install the serial multi-drop connection unit with its hook (1 place) using the DIN rail.

• Applicable DIN rail DIN46277 (width: 35mm)

(Install the DIN rail with screws at intervals of 150mm.)

„

Directly installed to panel

Install the serial multi-drop connection unit to the panel using 4.5mm holes (2 places).

8 - 12

8. OPTION

8.9 Serial Multi-Drop Connection Unit

8.9.4

Parts name

1)

Protective cover is installed

2)

4)

3)

7)

Protective cover is removed

5)

5)

8)

1

2

57 (2.25")

65 (2.56")

2- 4.5

9)

3

12)

10)

No.

1)

2)

3)

Name

Installation hole for the main unit

POWER

SD

LED

RD

ERROR

Terminating resistor selector switch

4)

5)

6)

7)

8)

Connector for the PLC communication

Connector selection switch for the PLC communication

USB port

Connector for the PLC communication

9)

Protective cover

Terminal block for the serial multi-drop communication

10) Power supply connector

11) Slider for installing the DIN rail

12)

Mode selection switch

(Slide switch)

11)

Unit: mm (inch)

Description

Installation hole (2-Φ4.5)

Lit in green when the power is properly supplied.

Lit in green when the data is being sent to PLC.

Lit in green when the data is being received from PLC.

Lit or blinking depending on the status.

Can be selected among 110 , OPEN, and 330 (set to "OPEN" by default).

D-Sub 9pin (Male), for RS-232 connection

Switch for selecting RS-422 or RS-232 (set to "RS-422" by default)

For connecting a PC (for changing the communication driver)

D-Sub 9pin (Female), for RS-422 connection

Protects unused D-sub connector, USB port, and switches.

Terminal block 5-pin (with a protective cover) M3 Tightening torque 0.5 to 0.6N•m

24VDC power supply connector insertion point (A dedicated cable is included.)

-

Do not operate.

(Set to right by default. When set to left, the module does not operate normally.)

4

5

6

7

8.9.5

Caution for compliance with EMC Directive

Please use the serial multi-drop connection unit while installed in conductive shielded control panels.

Programmable logic controllers are open-type devices that must be installed and used within conductive control panels.

Please secure the control panel lid to the control panel (for conduction).

Installation within a control panel greatly affects the safety of the system and aids in shielding noise from the serial multidrop connection unit.

8. OPTION

8.9 Serial Multi-Drop Connection Unit

8 - 13

8

8.10 Panel-Mounted USB Port Extension

GT14-C10EXUSB-4S panel-mounted USB port extension is a waterproof extension cable of the USB.

It is used to pull out the USB interface (host) on the back of GT14 to the surface of the control panel.

8.10.1 Applicable panel-mounted USB port extension

The following panel-mounted USB port extension is applicable for GT14.

Model name

GT14-C10EXUSB-4S

Description

Panel-mounted USB port extension

8.10.2 Parts name

The following shows the parts name of panel-mounted USB port extension.

Cap installation chart

Waterproof cap

USB plug

Ferrite core

Cable

Model name label

Seal

Nut

8.10.3 Installing procedure

„

Installed to panel

Install the panel-mounted USB port extension as follows with attention to a curve or a distortion of waterproof cap, seal, and nut.

Panel thickness: 2 to 4mm

(0.08 to 0.16inch)

Seal

Nut

Waterproof cap

19.4±0.1

(0.77

"

±0.01)

Unit: mm (inch)

Panel Cutting Dimensions

• The panel thickness is 2.0 to 4.0mm.

• For panel-mounted USB port extension, the panel surface with waterproof cap is compatible with IP67f.

• Tightening torque of nut is 0.294 to 0.343N•m. Overtightening or undertightening may disable the waterproof effect.

• Tighten the waterproof cap properly when the cable is not used.

8 - 14

8. OPTION

8.10 Panel-Mounted USB Port Extension

„

Precautions on installing the panel-mounted USB port extension

(1) Run power lines, servo amplifier drive wires, and panel-mounted USB port extensions so that they do not cross each other.

(2) Install the panel-mounted USB port extension away from noise sources such as equipment.

(3) Do not twist, bend at a sharp angle or a right angle, and stretch the panel-mounted USB port extension since the cable may be broken.

(4) Install it while considering the following control panel inside dimensions.

• Dimension between the back of the GOT and structures

1

2

3

80 (3.15") or more

4

• Dimension of the protruding cable

80 (3.15") or more

5

(5) Insert the USB plug part of the tip of the panel-mounted USB port extension securely to the USB port of the

GOT.

Since the USB plug part may be inserted loosely or unplugged by power of vibrations, impacts, or pulling, fix the cable to the structures inside the panel or the preventive hole from removing for the USB cable of the GOT main unit by using the banding band or others.

6

7

(6) Use the product after checking that the functions and performances operate correctly.

8. OPTION

8.10 Panel-Mounted USB Port Extension

8 - 15

8

8.11 RS-232/485 Signal Conversion Adapter

GT14-RS2T4-9P type RS-232/485 signal conversion adaptor enables conversion of RS-232 communication interface to

RS-485 communication interface.

For the wiring between the RS-232/485 signal conversion adapter and the controller, refer to the following manual.

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

8.11.1 Applicable RS-232/485 signal conversion adapter

The following RS-232/485 signal conversion adaptor is applicable.

Model name

GT14-RS2T4-9P

Contents

For GOT multi-drop connection, multi-channel function connection, temperature controller connection, and MODBUS(R)/RTU connection

8.11.2 Installing procedure of RS-232/485 signal conversion adapter

1.

Turn the GOT power off.

2.

Connect the RS-232/485 signal conversion adapter to the RS-232 interface on the GOT.

3.

Fix the RS-232/485 signal conversion adaptor to the

GOT using the provided M3 tapping screws.

Tightening torque: 0.3 to 0.6 N•m

8 - 16

5V power supply

(1) To use the RS-232/485 signal conversion adaptor, select [Communication Setting] [Communication

Setting] [5V power supply] [Yes] on the utility screen of GT14.

5V power supply is a function that supplies electrical power to the RS-232/485 signal conversion adaptor.

It cannot be used in other controllers. For details on the 5V power supply, refer to the following.

10.1.3 Communication setting contents

(2) [5V power supply] can be set with the GT 14 hardware version B or later.

In the hardware version A, since 5V power is always supplied, this setting operation is invalid.

(3) To use the RS-232/485 signal conversion adaptor, select CoreOS of version V05.28.00AP or later and the standard OS of version V05.28.00 or later for GT14. For details on the version confirmation, refer to the following.

13.1.2 OS version confirmation

8. OPTION

8.11 RS-232/485 Signal Conversion Adapter

9.

UTILITY FUNCTION

Utility is a function, which carries out connection of GOT and PLC, screen display and operation method settings, program/data control and self-check etc.

For the utility function list, refer to the following.

9.2 Utility Function List

9.1 Utility Execution

For utility execution, utility has to be displayed by installing BootOS and Standard monitor OS in the C drive (Flash memory).

There are following three types for the installing Standard monitor OS methods.

1) GT Designer3 GOT

USB interface or

Ethernet interface or

RS-232 interface

*1

Installed directly from GT Designer3

GT Designer3

2) GT Designer3

BootOS or Standard monitor OS installation

SD card or

USB memory

OS file write

GOT

BootOS or Standard monitor OS installation

3) GOT

When GOT is remote, installed easily using the SD card or USB memory

GT Designer3

SD card or

USB memory

*1

Install the SD card or USB memory in GOT

SD card or

USB memory

GOT

OS file upload

*1

BootOS or Standard monitor OS installation

Install OS from GOT to GOT using

SD card or USB memory

SD card or

USB memory

*1

Install the SD card or USB memory in GOT

When installing the BootOS and standard monitor OS, standard monitor OS has to be installed in GOT in advance.

For the installation which uses GT Designer3, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

For the installation which uses GOT, refer to the following.

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

10

12

13

14

15

9

11

16

9. UTILITY FUNCTION

9.1 Utility Execution

9 - 1

9.2 Utility Function List

9 - 2

The items in the following list can be set/operated on the utility screens.

Communication setting

GOT setup

Time setting & display

Program/data control

Item

Communication setting

Ethernet setting

Display

Operation

Transparent mode

Backup/restoration

Behavior of duplicate IPs

OS information

Alarm information

Project information

Hard copy information

Functions overview

Assigning channel numbers and communication drivers to communication interfaces

Setting communication parameters

Setting or deleting sequence program protection key words, canceling sequence program protection status (When connecting to FX series CPU)

Setting whether to supply 5V power or not

*1*2

Displaying the contents of Ethernet setting, changing the host

Switching message languages

Setting the startup screen display time and screen saving time

Setting the backlight to ON or OFF during screen saving

Setting the battery alarm display to ON or OFF

Adjusting brightness and contrast

Inverting colors

Setting the buzzer volume and window move buzzer

Setting the key sensitivity and key reaction speed

Changing security levels

Setting the utility call keys

Adjusting the touch panel

Setting the USB mouse and keyboard

Setting the channel No. to be used for the communication for the FA transparent function

Setting the storage locations for backup data and backup settings, and setting the maximum number of backup data

Trigger backup settings

Setting the GOT operation when a device with the same IP address as that of the

GOT is added to the network afterwards

Selecting a base clock

Displaying the clock current time

Setting the clock current time

Displaying the battery status

Installing or uploading OS, displaying OS property, checking OS data

Deleting and copying alarm log files

Converting alarm log files in G1A format CSV or TXT format

Downloading, uploading, deleting or copying project files, displaying project file property, checking project file data

Deleting or copying hard copy files, changing hard copy file names

Reference

10.

10.

10.

11.1

11.2

11.2.4

11.2.5

11.2.6

11.2.7

11.3

11.4

11.5

12.

13.2.1

13.2.2

13.2.3

13.2.4

Advanced Recipe information

Converting advanced recipe files in G1P format CSV or TXT format

Converting CSV or TXT format Advanced recipe files in G1P format

Deleting, copying or moving advanced recipe files, creating a new advanced recipe file

Deleting or moving advanced recipe folders, changing advanced recipe folder names, creating a new advanced recipe folder

Writing, reading or matching record data and deleting device values with the advanced recipe record list

Logging information

Memory card format

Memory information

USB device status display

Converting logging files in G1L format CSV or TXT format

Deleting, copying or moving logging files, changing logging file names

Deleting logging folders or creating a new logging folder

Formatting a SD card or USB memory, internal SRAM

Displaying the available memory of the GOT

SRAM control

Displaying the status of USB device

Confirming the SRAM user area usage, backing up or restoring the data in the

SRAM user area, and initializing the SRAM user area

GOT data package acquisition Copying the OS, special data, and project data to a SD card or USB memory

13.2.5

13.2.6

13.2.7

13.2.8

13.2.9

13.2.10

13.2.11

9. UTILITY FUNCTION

9.2 Utility Function List

Debug & self check

Clean

*1

*2

Item

Debug

System monitor

A list editor

FX list editor

Backup/restoration

Memory check

Self check

Display check

Touch panel check

I/O check

System alarm display

GOT start time

Functions overview

Device monitor of PLC, test function, present value change of the buffer memory monitor and the buffer memory of intelligent module

Sequence program and parameter change of ACPU

Sequence program and parameter change of FX PLC

Executing backups, executing restorations, and deleting backup data

Memory check of A drive, C drive, D drive, and E drive

Drawing check

Font check

Touch panel operation check

Connected target confirmation, self-loopback check

Displaying GOT errors and CPU errors, resetting GOT errors

Displaying GOT start date and time, current time, accumulated operating hours

Reference

14.1.1

14.1.2

14.1.3

14.1.4

14.2.1

14.2.2

14.2.3

14.2.4

14.2.5

14.3

14.4

Clean Displaying the screen for cleaning the display

15.

Do not use this function for other than 5V power supply to the RS-232/485 signal conversion adaptor.

7.11 RS-232/485 signal conversion adapter

[5V power supply] can be set with the GT 14 hardware version B or later. In the hardware version A, since 5V power is always supplied, this setting operation is invalid.

9

10

11

12

13

14

15

16

9. UTILITY FUNCTION

9.2 Utility Function List

9 - 3

9.3 Utility Display

To display setting screens for each utility, the main menu must be displayed first.

(1)

(1)

(2) (2)

(1) Main menu

The menu items that can be selected from the GOT utility are displayed.

Touching a menu item in the main menu displays the setting screen or following selection screen for the item.

(2) System message switch button

This button switches the language used for the utility screen and system alarms.

Touching the [Language] button displays the Select Language screen.

1.

Touch the button of a desired language and then [OK] button, and the language is selected.

2.

Touching the [ ] button restarts the GOT and the language of the utility is switched to the selected one.

9 - 4

9. UTILITY FUNCTION

9.3 Utility Display

9

When starting the GOT without selecting any language or the selected language and the installed fonts are not matched.

The following screen is displayed.

Touching the button of a desired language restarts the GOT and the language is switched to the selected one.

10

11

12

(1) Selectable languages

The system message switch button is displayed only for the selectable languages.

The selectable languages differ depending on the fonts installed in the GOT.

For the relation between the selectable languages and the fonts, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamental) 2.5 Specifications of Applicable

Characters

(2) System language switching using the device

The system language can be switched using the system language switching device set with GT Designer3.

For the setting method of the system language switching device, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamental)

4.3 Language Switching Device Setting (GOT Environmental Setting: Language Switching)

13

14

15

16

9. UTILITY FUNCTION

9.3 Utility Display

9 - 5

9.3.1

Display operation of main menu

The following four types of operation can display the main menu.

(Display the main menu after installing the Standard monitor OS from GT Designer3 to the built-in flash memory of the

GOT.)

(1) When project data is undownloaded

After the GOT is turned on, a dialog box for notifying of absence of project data is displayed. After the dialog box is displayed, touch the OK button to display the main menu.

GOT power on

Touch the OK button.

(2) When touching menu call key

Touching the menu call key while user-created screen is displayed displays the main menu.

The menu call key is set in the position on the GOT screen upper left corner at factory shipment.

Horizontal display Length display

*

* The utility screen is a factory installed horizontal format screen that cannot be edited.

The menu call key can be set by the GOT utility or GT Designer3.

For menu call key setting, refer to the following.

• 11.2.5 Utility Call Key Setting

• GT Designer3 Version1 Screen Design Manual (Fundamental)

4.9 GOT Display and Operation Setting (GOT Environmental Setting: GOT Setup)

9 - 6

(1) Prohibited simultaneous 2-point presses

Do not touch 2 points or more on the GOT screen simultaneously. Touching 2 points or more simultaneously may activate a part other than the touched point.

(2) Pressing time of the utility call key

When having set [Pressing time] of the menu call key setting screen to other than "0 (s)", keep pressing the touch panel for the period set to [Pressing time] or more before leaving the finger from the touch panel.

For menu call key setting, refer to the following.

11.2.5 Utility Call Key Setting

(3) When the utility call key is set to the zero point

Even when the utility call key is set to the zero point, you can display the main menu using either of the following two operations:

• Pressing the special function switch set on the user-created screen

• Keeping pressing the upper left corner while the [Booting.] message is displayed after powering up.

9. UTILITY FUNCTION

9.3 Utility Display

(3) When touching special function switch (utility)

Touching the special function switch (utility) while user-created screen is displayed displays the main menu.

The special function switch (utility) can be set as a touch switch that is displayed on a user-created screen by

GT Designer3.

9

10

Special function switch

(Utility)

For the details of the special function switch, refer to the following.

GT Designer3 Version1 Screen Design Manual (Functions)

(4) When powering ON the system

The [Booting.] message is displayed after powering up. After that, keep pressing the upper left corner to display the main menu.

If the upper left corner is pressed before the display of the [Booting...] message, the OS installation function starts. Therefore, press the upper left corner after the [Booting...] message is displayed.

11

12

Booting.

Press the screen upper left corner during [Booting...] message display.

13

When limiting the display and operation of the utility

When limiting the display and operating users, set a password to the GOT using the GT Designer3. If a user tries to display the main menu of the utility, the password input screen is displayed.

For details on setting passwords, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

14

15

16

9. UTILITY FUNCTION

9.3 Utility Display

9 - 7

9.3.2

Utility basic configuration

The basic configuration of the screen is as follows.

Title display Close/Return button

(1) Title display

The screen title name is displayed in title display part.

Scroll key

Screen

Title display

Title display

(2) Close/Return button

When a middle screen of the layers is displayed, if the

[ ]

(Close/return) button in the right corner of screen is touched, returns to the previous screen.

If this button is touched when directly displayed from monitor screen, the screen is closed and returns to monitor screen.

(3) Scroll button

For screens in which the content does not fit on one screen page, there is a right or down scroll button on the screen.

Scroll one line/column

Scroll window

9 - 8

9. UTILITY FUNCTION

9.3 Utility Display

9.3.3

Basic operation of settings change

„

Change of setting value

11

Setting item Select button Setting item Select button

(1) Setting item, select button

Touch the select button to change the settings.

The setting methods differ depending on the setting items.

The following types of setting method are available.

(a) Switch the setting value.

Touch the button to switch the setting value as shown in

ON OFF

.

(b) Enter the setting value with a keyboard.

It is a key for inputting the numerical value. Touching this button displays a keyboard on the GOT screen.

For the operation of keyboard, refer to the next page.

(c) Move to another setting screen.

Touching this button moves to another setting screen.

For the setting method of each setting item, refer to the setting operation of each setting screen.

(2) [OK] button, [Cancel] button, [ ] (Close/Return) button

Reflect or cancel the changed settings.

(a) [OK] button

Touching this button reflects the changed settings.

(b) [Cancel] button

Touching this button cancels the changed settings and return to the previous screen.

(c) [ ] (Close/Return) button

Touching this button closes the screen. Depending on the setting item, the GOT restarts.

If [ ] button is touched without touching [OK] button, the following dialog box will be displayed.

(If the settings are not changed, the dialog box is not displayed.)

Operate following the message of the dialog box.

12

13

14

15

9

10

16

9. UTILITY FUNCTION

9.3 Utility Display

9 - 9

„

Keyboard operation

1.

Touch the numerical value to be changed.

2.

Keyboard for numerical input is displayed and cursor is displayed simultaneously.

The key board display position changes by the position of numerical value touched.

(At the time of numerical input, displayed in the position which will not interrupt the inputting.)

Cursor

Keyboard

3.

Input numeric with keyboard.

• [0] to [9] Key: Input the numeric.

• [Enter] Key: Completes numeric input and closes the keyboard.

• [Cancel] Key: Cancels numeric input and closes the keyboard.

• Key: Moves the cursor to the right or left side. (Available only if any selectable item is at the right/left side of the cursor.)

• [Del] Key: [Del] key is used when canceling the input by 1 character.

• [*] key and the key which is not mentioned do not function.

4.

Touching [Enter] key completes numeric input and closes keyboard.

9 - 10

9. UTILITY FUNCTION

9.3 Utility Display

10. COMMUNICATION INTERFACE

SETTING (COMMUNICATION

SETTING)

In [Communication Setting], the communication interface names and the related communication channel, communication driver names display and channel numbers are set.

Moreover, in [Communication Detail setting], the communication interface details are set. (Communication parameters setting)

Function

Communication Setting

Ethernet setting

Description

The setting contents of the communication interface can be checked or changed.

Whether to supply 5V power or not can be set.

The contents of the Ethernet setting can be checked and the host can be changed.

Reference

10-1

10-1

10-15

10.1 Communication setting

10.1.1 Communication setting functions

Function

Channel-Driver assign

Assign Ethernet I/F

Channel No. (Ch No.) setting

Communication parameters setting

5V power supply

Description

Change the assignment of channel No. and communication driver name.

Change the assignment of channel No. and communication driver name of the device connected using the

Ethernet interface.

Set the channel numbers of the communication interface (Standard interface).

Set communication parameters of communication devices.

Set whether to supply 5V power or not when the RS-232/485 signal conversion adaptor is used.

10.1.2 Display operation of Communication Setting

10

12

13

9

11

Communication setting

(

Main menu

9.3 Utility Display)

14

Touch

[Comm.setting]

Touch

[Communication setting]

Communication setting

15

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

10 - 1

10.1.3 Communication setting contents

This section describes setting items and display contents for Communication Setting.

(3)

(3)

(3)

(2)

(4)

(2)

(2)

(4)

(2)

(4)

(4)

(6)

(5) (1)

(1) Channel-Driver assign

Channel No. can be assigned to the communication driver installed in the GOT.

(a) Not writing [Communication Setting] in drawing software

Without writing [Communication Setting] in drawing software, communication with a controller is available after assigning the channel No. with this function.

10.1.4

■

Channel-Driver assign operation

(b) When changing the assignment of the communication driver to the channel in the Utility

Without using drawing software, the assignment of communication drivers to channels can be changed.

(When changing a communication driver, the alternative communication driver has to be installed in GOT in advance.)

(2) Standard interface display BOX

Display the communication interface included as standard in GT14. There are the following 4 types.

[GOT front face] [GOT rear face]

10 - 2

USB interface (Standard interface)

RS-422 interface (Standard interface)

RS-232 interface (Standard interface)

Ethernet interface (Standard interface)

RS-232................. For communicating with PC (drawing software), bar code reader, RFID, controller or controller

RS-422/485.......... For communicating with controller

USB...................... For communicating with PC (drawing software)

Ethernet................ For communicating with PC (drawing software) or controller

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

(3) Channel number specification menu BOX

Set channel No. to use with standard interface.

Refer to this section (4) for driver that can be assigned to each channel.

0: Set when the communication interface is not used.

1, 2:

8:

Set when connecting to a controller.

Set when connecting with a bar code reader or RFID.

9

*1

:

*:

Set when connecting with PC (drawing software).

Set when using the function that uses the gateway function (when connection types except the

Ethernet connection is used for connecting to controllers), Ethernet download function.

• Fixed to 9 for the USB interface.

*1 Cannot be assigned with Ethernet I/F Assignment.

(4) Driver display BOX

The name of communication driver assigned to the channels or the driver set with the Communication Setting of drawing software is displayed.

For details of drivers to be displayed, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

Displays [None] in the driver display BOX in case of the following.

• The communication driver is not installed. (

13.2.1 OS information)

• In channel number specification menu BOX, [0] is set.

When the channel number is set to [9] to RS-232 interface, the communication driver [Host (PC)] or [Host

(model)] can be selected.

When the channel number is set to [9] to USB interface, the communication driver [Host (PC)] is automatically assigned.

(5) Assign Ethernet I/F

The communication settings for the Ethernet connection can be made.

Only Ethernet interface built-in model can display this button.

Ethernet I/F Assignment can assign up to two channels per interface.

10.1.4

■

Assign Ethernet I/F operation

(6) 5V power supply

Set the 5V power supply when using the RS-232/485 signal conversion adaptor.

10.1.4

■

5V power supply operation

9

10

11

12

13

14

Precautions for communications between GOT and controller

(1) Installing communication driver and downloading Communication Setting

The following below is required for the communication interface to communicate with the controller.

1) Installing communication drivers (Up to 4 communication drivers)

2) Assigning the channel number and communication driver for the communication interface

3) Downloading the contents (project data) assigned in 2).

Perform1), 2), 3) by drawing software.

15

For details, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

(2) When Communication Setting has not been downloaded.

When [Communication Setting] has not been downloaded using drawing software, make the communication settings in the drawing software or on the utility screen of the GOT.

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

10 - 3

10.1.4 Communication setting operation

„

Channel-Driver assign operation

The following describes how to operate the Channel-Driver assign.

The example of changing to the direct CPU connection (Communication driver: [A/QnA/L/QCPU, LJ71C24,

QJ71C24]) for the GOT of the computer link connection (Communication driver: [AJ71QC24, MELDAS C6*]) is used.

Before starting operation

After Communication Setting is executed, the GOT automatically restarts.

If the project data is downloaded, GOT starts monitoring the communication device after restarting.

Execute this setting after carefully confirming the safety.

1.

Install communication driver [A/QnA/L/QCPU, L/

QJ71C24] to GOT.

(Download of [Communication Setting] from drawing software is not required.)

After installing communication driver, touch the

[Channel Driver assign] button in [Communication

Setting].

2.

Touch the [Change assignment] button on the displayed screen as shown left.

3.

As the communication driver ([A/QnA/L/QCPU, L/

QJ71C24]) installed in the GOT is displayed, touch it.

(Continued to next page)

10 - 4

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

„

Channel number setting operation

Keyboard

4.

The screen returns to the [Channel-Driver assign] screen and touch the [OK] button.

5.

Touch [ ] button to return to the [Communication

Setting] screen.

9

10

6.

Confirm that the selected communication driver ([A/

QnA/L/QCPU, L/QJ71C24]) is assigned.

7.

After confirming, touch the [OK] button.

8.

Touching the [ ] button restarts the GOT and the

GOT operates with the changed settings.

11

12

1.

Touch channel number specification menu BOX to be set.

2.

The cursor for the channel number specification menu BOX is displayed.

Simultaneously the keyboard for a numerical input is displayed.

13

14

3.

Input the channel number from the keyboard and touch [Enter] key, and the value is defined.

Simultaneously, the name of the communication driver corresponding to the channel number assigned by drawing software is displayed in the driver display BOX.

15

„

Communication detail setting switching operation

If the driver display BOX is touched on the communication setting screen or Ethernet I/F assign screen, the screen switches to the detailed setting screen of the related controller device.

(

10.2 Communication Detail Setting)

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

10 - 5

„

Assign Ethernet I/F operation

The following describes how to operate the Ethernet I/F assign.

The setting operation is same as that of the communication setting screen.

1.

Touch the [Assign Ethernet I/F] button in

[Communication Setting].

2.

After the screen shown left is displayed, touch the channel number specification menu BOX when

( changing the channel number.

10.1.4

■

Channel number setting operation)

3.

For changing the parameter settings, touch the driver display BOX.

(

10.2Communication Detail Setting)

4.

Touching the [OK] button reflects the changed settings. Touching [ ] button returns the screen to the [Communication Setting] screen.

5.

Touch the [OK] button in the [Communication Setting] screen.

6.

Touching the [ ] button restarts the GOT and the

GOT operates with the changed settings.

10 - 6

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

„

5V power supply operation

The following describes how to operate the 5V power supply.

1.

Touch the [5V power supply] button in

[Communication Setting].

11

2.

Touch the setting item of [5V power supply] when using the RS-232/485 conversion adaptor. The setting content is changed by touching.

12

3.

Select [Yes] to change the setting of the 5V power supply.

Touching the [OK] button reflects the changed settings. Touching [ ] button returns the screen to the [Communication Setting] screen.

13

14

"*" indicating the setting to supply the 5V power supply is displayed.

4.

Touch the [OK] button in the [Communication Setting] screen.

5.

Touching the [ ] button restarts the GOT and the

GOT operates with the changed settings.

15

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.1 Communication setting

10 - 7

9

10

10.2 Communication Detail Setting

10.2.1 Communication detail setting functions

Function

Communication parameters setting

Keyword Register

Keyword Delete

Keyword Clear

Keyword Protect

Description

Set various communication parameters of communication devices. The settable parameters differ according to the communication device.

For the FX series PLCs, key word for protecting program in the PLC can be set.

For the FX series PLCs, key word for protecting program in the PLC can be deleted.

For the FX series PLCs, the program protection status in the PLC can be cancelled.

For the FX series PLCs with the 2nd keyword in use, the cancelled program protection in the PLC can be reactivated.

10.2.2 Display operation of Communication Detail setting

„

Communication settings

1.

Touch the driver display BOX of the communication parameter to be set in the [Communication setting] screen.

Communication parameter

2.

The screen switches to the [Communication Detail setting] screen.

Set communication parameters from this screen.

For the setting change operation, refer to the following.

9.3.3 Basic operation of settings change

Communication parameter setting by drawing software

Select [Common Settings] [Communication Settings] from GT Designer3 to enter the communication parameters for each communication driver.

When changing the communication parameters after downloading project data, change the setting at communication detail setting of GOT.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

10 - 8

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

9

„

Assign Ethernet I/F

Several drivers are assigned to the same Ethernet interface. However, only one GOT IP address is assigned per interface.

By changing the settings of one interface, the GOT IP address, GOT port No. download, default gateway and subnet mask settings of other drivers, which are assigned to the same interface, are also changed.

1.

Touch the [Assign Ethernet I/F] button in

Communication Setting.

10

2.

Touch the driver display BOX of the communication parameter to be set in Ethernet I/F assignment.

11

12

3.

The screen switches to the [Communication Detail setting] screen.

Set communication parameters from this screen.

For the setting change operation, refer to the following.

9.3.3 Basic operation of settings change

13

14

Communication parameter setting by drawing software

Select [Common Settings] [Communication Settings] from GT Designer3 to enter the communication parameters for each communication driver.

When changing the communication parameters after downloading project data, change the setting at communication detail setting of GOT.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

15

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

10 - 9

10.2.3 Display contents of Communication Detail setting

The contents of communication detail setting varies according to driver type.

This section explains setting items different from the communication detail setting of the drawing software.

For setting items other than described in this section, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

„

Communication detail setting of host (modem)

On the communication detail setting screen of host (modem), the communication setting between the GOT and the modem and the modem operation can be executed.

Item

PC connection type

Transmission Speed

Data Bit

Stop Bit

Parity

Init. AT command

Modem operation

Description

Select the connection method to the PC.

Set the transmission speed when communicating.

Set the data bit when communicating.

Set the stop bit length when communicating.

Set whether to execute or not the parity check during communication. When executing, set the type of the parity check.

Set the AT command for initialize the modem.

Touch the [Init.] button to initialize the modem.

Touch the [Cut] button to disconnect the line.

-

Setting range

Host (PC) / Host (Modem)

<Default: Host (PC)>

9600/19200/38400/57600/115200

<Default: 115200>

7bit/8bit <Default: 8bit>

1bit/2bit <Default: 1bit>

Odd/Even/None <Default: Odd>

<Default: AT & FE0%C0 & K0 & D0W2S0=1>

10 - 10

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

„

Keyword settings of MELSEC-FX

On the communication detail setting screen of MELSEC-FX, registration, deletion, cancellation, or protection of the keyword for FX series PLC can be executed.

9

10

11

(1) Regist

Keyword is registered.

1.

Touching the [Regist] key displays the Registration Selection screen.

For a FX PLC

*1

that is not compatible with the customer keyword, the keyboard for the keyword input of is displayed.

Select [Keyword] or [Keyword and Customer keyword].

When the [Enter] key is touched, the selection is completed and the keyboard for the keyword input is displayed.

12

13

14

Selection Description

When [Keyword] is selected Only keyword can be registered.

When [Keyword and Customer keyword] is selected The Customer Keyword can be registered after registration of the keyword.

*1: For details on FX PLC compatible with customer keyword, refer to the manual of the PLC used.

The customer keyword allows the user to clear the protection set by a keyword. However, the protection cannot be deleted.

15

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

10 - 11

2.

When the registration is selected or the Regist key is touched on a PLC not compatible with the customer keyword, the keyboard for the keyword input is displayed in a pop-up window.

When the keyword is input and the [Enter] key is touched, registration is completed.

When [Keyword and Customer Keyword] is selected on the selection screen for the registration, the Customer

Keyword entry screen of is displayed.

For the keyword, 8 digits from 0 to 9 or A to F must be set.

Setting

Target PLC

When keyword and 2nd keyword are registered

When only keyword is registered

FX PLC compatible with 2nd keyword

*1

[Registration conclition]

*2

can be selected.

[Registration conclition]

*2

cannot be selected.

FX PLC not compatible with 2nd keyword

*1

-

*1 For details on FX PLC compatible with 2nd keyword, refer to the manual of the PLC used.

*2 [Registration conclition]

Options can be selected among [Read/Write Protect], [Write Protect], or [All Protect].

For access restrictions of each setting, refer to the manual of the PLC used.

3.

When [Keyword and Customer Keyword] is selected on the selection screen for registration and the keyword input is completed, the Customer Keyword registration screen is the displayed.

When the customer keyword is input and the [Enter] key is touched, registration is completed.

To set the customer keyword, 8 digits from 0 to 9 or A to F must be used.

10 - 12

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

9

(1) Selection of keyword protection level

For the devices which can perform the online operation of FX PLC, 3 levels of protection can be set.

When the monitoring or setting change by online devices is needed, set the keyword taking the following into consideration.

(a) When only keyword is registered

Protection level is selected by the head character of keyword.

All operation prohibition: Set the keyword starting with one of A, D to F, or 0 to 9.

Read/incorrect write protection: Set the keyword starting with B.

Erroneous write prohibition: Set the keyword starting with C.

(b) When keyword and 2nd keyword are registered

Protection level is selected by [Registration conclition].

(2) Applicability of monitoring for each keyword protection level

The applicability of monitoring for each protection level is as follows.

When only keyword is registered

When keyword and 2nd keyword are registered

Item

All operation prohibition

Read/

Incorrect write protection

Erroneous write prohibition

All Protect

Read/Write prohibition

Write

Protect

Device monitoring

Device change

T, C setting values and file register

(from D1000)

Other than the above

*1 *1 *1

Keyword unregistered/ protection cancelled

*1 When the T, C setting values are specified indirectly, changing devices is available.

(3) Difference between [All Protect] and [All operation prohibition]

When [All Protect] is selected, both device display and input by the programming tool or GOT are prohibited.

When [All operation prohibition] is selected, device display and input are possible although operations by the programming tool are all prohibited.

10

11

12

13

14

15

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

10 - 13

(2) Delete

Registered keyword is deleted.

1.

Touching the [Delete] key pops up a keyboard for keyword input.

2.

When the correct keyword is input and the [Enter] key is touched, the keyword is deleted.

Target PLC

FX PLC compatible with 2nd keyword

FX PLC not compatible with 2nd keyword

Setting

Input a keyword to be deleted.

Input a keyword to be deleted only into "keyword".

"2nd keyword" is ignored.

(3) Clear

To access an FX PLC where a keyword has been registered, keyword protection is cancelled.

1.

Touching the [Clear] key pops up a keyboard for keyword input.

2.

When the correct keyword is input and the [Enter] key is touched, the protection is cancelled.

10 - 14

Target PLC

FX PLC compatible with 2nd keyword

FX PLC not compatible with 2nd keyword

Setting

Input a keyword or Customer Keyword to cancel the protection.

Input a keyword only into "keyword" to cancel the protection.

"2nd keyword" is ignored.

(4) Protect

A keyword with cancelled protection is reactivated for protection.

1.

Touching the[Protect] key activates keyword protection.

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.2 Communication Detail Setting

10.3 Ethernet Setting

10.3.1 Ethernet setting functions

The contents of the Ethernet setting in drawing software can be checked.

The setting of the host station can be changed.

For Ethernet setting, refer to the following.

GOT1000 Series Connection Manual for GT Works3

10.3.2 Display operation of Ethernet setting

Communication setting

(

Main menu

9.3 Utility Display

)

Touch

[Comm.setting]

Ethernet setting

Touch

[Ethernet.setting]

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.3 Ethernet Setting

10 - 15

13

14

15

11

12

9

10

16

10.3.3 Display contents of Ethernet setting

The following describes the setting items and the display contents of the Ethernet setting.

(1) Channel selection tab

Channels can be switched.

Switching to the channel which does not have the Ethernet setting is not available.

[*] is displayed on the tab of the channel whose setting is changed.

(2) Ethernet setting item

The contents of the Ethernet setting configured in drawing software are displayed.

The setting of the host station can be changed.

■

Change of host

(3) Restore default settings

Touching this button cancels the change of the setting and returns the setting to the status when the project data was written.

(1) How to cancel the change of the setting in the [Ethernet setting] screen

Cancel the settings changed in the [Ethernet setting] screen with the [Restore default settings] button.

The changed settings remain until they are canceled with the [Restore default settings] button.

The changed settings are not canceled even if writing the project data or OS to the GOT.

When the project data is written to the GOT without canceling the changed settings, those changed settings are reflected to the Ethernet setting of the written project data.

(If the written project data does not have a channel with same Ethernet settings as that of the channel changed in [Ethernet setting] screen, the changed settings are not reflected.)

(2) Range where the settings changed in the [Ethernet setting] screen are reflected

The settings changed in the [Ethernet setting] screen are valid in the GOT. On the other hand, they are not overwritten to the project data written to the GOT.

The changed settings are not reflected to the project data which is read from the GOT after changing the settings.

If the GOT data is copied with the GOT data package acquisition, the change in the [Ethernet setting] screen is reflected to the copied data.

10 - 16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.3 Ethernet Setting

„

Change of host

1.

Touch the device to be set as the host.

2.

Touch the [OK] button.

3.

Touching the [ ] button restarts the GOT and the

GOT operates with the changed settings.

11

12

9

10

13

14

15

16

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.3 Ethernet Setting

10 - 17

10 - 18

10. COMMUNICATION INTERFACE SETTING (COMMUNICATION SETTING)

10.3 Ethernet Setting

11. DISPLAY AND OPERATION

SETTINGS (GOT SET UP)

Setting screen for display and setting screen for operation can be displayed from the utility screen.

In the setting screen for display and the setting screen for operation, the following settings can be set.

Item

Display

Operation

Transparent mode

Backup/restoration

Behavior of duplicate IPs

Description

Language, opening screen time, screen save time, screen save backlight, battery alarm display and invert colors

Adjusting brightness and contrast

Buzzer volume, window move buzzer volume, key sensitivity, key reaction speed, touch detection mode

Security setting

Utility call key

Touch panel calibration

USB mouse/keyboard setting

Ch No.

Setting the storage locations for backup data and backup settings, and setting the maximum number of backup data

Trigger backup settings

Setting the GOT operation when a device with the same IP address as that of the GOT is added to the network afterwards.

Reference

11-1

11-5

11-6

11-9

11-11

11-13

11-15

11-17

11-18

11-20

11-21

10

11

12

11.1 Display Setting

11.1.1 Function of Display

Setting regarding display is possible.

The items which can be set are shown below. When each item part is touched, the respective setting becomes possible.

Item Description Setting range

Language

*1

Opening screen time

Screen save time

Screen save backlight

Battery alarm display

Brightness, contrast

Invert colors

(only GT1450-Q)

*1

*2

Confirmation of the current language and switching language can be performed regarding with the language displayed by utility and dialog box.

The title display period at the main unit boot can be set.

The period from the user stops the touch panel operation till the screen save function starts can be set.

Whether turning ON or OFF the backlight simultaneously at the start of the screen save function can be specified.

Whether to display system alarm when the voltage of the GOT internal battery has dropped can be specified.

The brightness can be adjusted.

■

Brightness, contrast

For the user-created screen and the utility screen, whether to invert the displayed colors can be specified.

-

(Japanese)

(English)

(Chinese (Simplified))

(Chinese (Traditional))

(Korean)

(German)

(At factory shipment: User's selection)

0 to 60 seconds

*2

(At factory shipment: 5 seconds)

0 to 60 minutes

(At factory shipment: 5 seconds)

ON/OFF

(At factory shipment: OFF)

ON/OFF

(At factory shipment: OFF)

ON/OFF

(At factory shipment: OFF)

Only selectable languages are displayed.

The selectable languages differ depending on the fonts installed in the GOT.

For details of the fonts, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

Setting 0 does not hide the title screen.

The title screen is always displayed for 4 seconds or longer (which changes depending on the project data contents).

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.1 Display Setting

11 - 1

13

14

15

16

9

(1) Display setting by GT Designer3

Select [Common Settings] [GOT Environment Settings] [GOT Setup] from GT Designer3 to make the settings of opening screen time, screen save time and screen save backlight.

To change a part of the setting after downloading the project data, change the setting at the display setting of

GOT.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

(2) Screen save time

Using the system information function can compulsorily switch the controller to the screen saving status

(Forced Screen Saver Disable Signal) or disable the screen save time (Automatic Screen Saver Disable

Signal) set with Utility.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

(3) Screen save backlight

When [Screen save backlight] is set to [ON], using the system information function (Backlight OFF output signal) can switch the backlight OFF from the controller.

When [Screen save backlight] is set to [OFF], the above signal has no effect on the screen save backlight.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

11.1.2 Display operation of Display

(

Main menu

9.3 Utility Display)

Touch

[GOT setup]

GOT setup

Touch

[Display]

Display

Touch an item to change settings

11 - 2

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.1 Display Setting

11.1.3 Display operations

„

Language

9

1.

Touching the setting items displays the Select

Language screen.

10

2.

Touching the button of a desired language selects the language and returns the screen to the Display screen.

11

3.

Touching [OK] button defines the setting contents.

12

13

Touching [ ] button without touching [OK] button displays the dialogue box shown on the left.

[OK] button: The changed value is canceled, and the screen is closed.

[Cancel] button:The display setting screen is displayed.

4.

Closing the display setting and GOT setup screens after completing the setting of all items to change with [ ] button restarts the GOT and reflects the setting contents.

14

15

(1) Selectable languages

The system message switch button is displayed only for the selectable languages.

The selectable languages differ depending on the fonts installed in the GOT.

For the relation between the selectable languages and the fonts, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamental) 2.5 Specifications of Applicable

Characters

(2) System language switching using the device

The system language can be switched using the system language switching device set with GT Designer3.

For the setting method of the system language switching device, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

4.3 Language Switching Device Setting (GOT Environmental Setting: Language Switching)

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.1 Display Setting

11 - 3

„

Opening screen, screen save time

1.

Touching the setting time (numerical) displays the keyboard.

Input numeric with the keyboard.

2.

Touching [OK] button defines the setting contents.

Touching [ ] button without touching [OK] button displays the dialogue box shown on the left.

[OK] button: The changed value is canceled, and the screen is closed.

[Cancel] button:The display setting screen is displayed.

3.

Closing the display setting and GOT setup screens after completing the setting of all items to change with [ ] button restarts the GOT and reflects the setting contents.

„

Screen save backlight, battery alarm display, invert colors

1.

Touching the setting item changes the setting items.

2.

Touching [OK] button defines the setting contents.

11 - 4

Touching [ ] button without touching [OK] button displays the dialogue box shown on the left.

[OK] button: The changed value is canceled, and the screen is closed.

[Cancel] button:The display setting screen is displayed.

3.

Closing the display setting and GOT setup screens after completing the setting of all items to change with [ ] button restarts the GOT and reflects the setting contents.

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.1 Display Setting

„

Brightness, contrast

(For monochrome screen)

1.

Touching the setting items displays the brightness contrast adjustment screen.

9

10

2.

Brightness can be adjusted by touching [+], [-] key of brightness adjustment.

3.

Contrast can be adjusted by touching [+], [-] key of contrast adjustment.

4.

Touching [OK] button defines the setting contents.

11

12

Touching [ ] button without touching [OK] button displays the dialogue box shown on the left.

[OK] button: The changed value is canceled, and the screen is closed.

[Cancel] button: The brightness/contrast adjustment screen is displayed.

13

14

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.1 Display Setting

11 - 5

11.2 Operation Setting (Settings Regarding Operation)

11.2.1 Operation setting functions

Setting regarding GOT operation can be set.

The items which can be set are described below. Touching the each item part makes the respective setting become possible.

Function Description

Buzzer volume setting Buzzer volume setting can be changed.

Window move buzzer volume setting Whether turn ON/OFF buzzer when move window can be selected.

Setting range

OFF/SHORT/LONG

(At factory shipment: SHORT)

ON/OFF

(At factory shipment: ON)

Security setting screen change

Security level change screen can be displayed.

11.2.4 Security level change

-

Utility call key screen change

Key sensitivity setting

Touch panel calibration

USB mouse/keyboard setting

Utility call key setting screen can be displayed.

11.2.5 Utility Call Key Setting

The sensitivity of touch panel when GOT screen is touched can be set.

E.g. a setting can be changed when double-touch is made when touching the GOT screen only once. (For preventing chattering)

Touch panel reading error can be corrected.

11.2.6 Adjusting the touch panel position (Touch panel calibration)

Set the setting items related with USB mouse/keyboard.

11.2.7 USB mouse/keyboard setting

-

-

-

1 to 8

Operation setting by GT Designer3

Select [Common Settings] [GOT Environment Settings] [GOT Setup] from GT Designer3 to make the settings of buzzer sound and buzzer sound at window move.

To change a part of the setting after downloading the project data, change the setting at the display setting of GOT.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

11 - 6

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11.2.2 Display operation of Operation

(

Main menu

9.3 Utility Display)

GOT setup

Touch

[GOT setup]

Touch

[Operation]

Operation

Touch an item to change settings

11

12

9

10

13

14

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11 - 7

11.2.3 Setting operation of operation

„

Buzzer volume, window move buzzer volume

1.

Touching the setting item changes the setting items.

2.

Touching [OK] button defines the setting contents.

Touching [ ] button restarts the GOT and reflects the setting contents.

„

Security setting

For the security setting operation, refer to the following.

11.2.4 Security level change

„

Utility call key

For the utility call key operation, refer to the following.

11.2.5 Utility Call Key Setting

„

Key sensitivity setting

1.

Touching the setting items displays the keyboard.

Enter the numerical value from the keyboard.

2.

The key response speed

*1

corresponding to the

[Key sensitivity] setting is displayed.

3.

Touching [OK] button defines the setting contents.

Touching [ ] button restarts the GOT and reflects the setting contents.

*1 Relation between the [Key sensitivity] setting and [Key reaction speed]

The larger the set value in [Key sensitivity] is, the shorter the time taken from touching the touch panel until the GOT responds becomes. E.g. decrease the value set for [Key sensitivity] when double-touch is made when touching the GOT screen only once.

(Decrease the reaction speed.)

The relation between the [Key sensitivity] setting and [Key reaction speed] is as follows.

[Key sensitivity] setting

Quick response

8 7 5 4 3 2

Slow response

1

[Key reaction speed] -20ms -10ms

6

0ms

(Standard)

+10ms +20ms +40ms +80ms +120ms

„

Touch panel calibration

For touch panel calibration operation, refer to the following.

11.2.6 Adjusting the touch panel position (Touch panel calibration)

„

USB mouse/keyboard setting

For the USB mouse/keyboard setting, refer to the following.

11.2.7 USB mouse/keyboard setting

11 - 8

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11.2.4 Security level change

„

Security level change functions

Changes the security level to the same security level set by each object or screen switch.

To change the security level, input the password of the security level which is set in GT Designer3.

Security level setting, Password setting................

GT Designer3 Version1 Screen Design Manual (Fundamentals)

9

10

Restrictions on screen display

The security level change screen cannot be displayed when project data do not exist in GOT.

Change the security level after downloading the project data to GOT.

„

Display operation of Security level change

(

Main menu

9.3 Utility Display)

GOT setup

Operation

Touch

[GOT setup]

Touch

[Operation]

Touch

[Security setting]

11

12

13

Security setting

Touch

[Security level change]

Security level change

14

Input the password of the security level which is set in Drawing software

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11 - 9

„

Security level change operation

(1) Password input operation

1.

By touching [0] to [9] , [A] to [F] key, the password of the changed security level is input.

2.

When correcting the input character, touch [Del] key to delete the correcting character and input the password again.

3.

After inputting password, touch the [Enter] key.

When the password matches, a message notifying successful change of the security level is displayed.

When the password does not match, an error message is displayed.

4.

Touching [OK] button returns the screen to the password input screen again.

5.

Touching [ ] button returns the screen to the security setting screen.

About forgetting to return to the original level after changing security level temporarily

When use GOT after temporarily changing the security level, do not forget to return the security level to the original level.

11 - 10

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11.2.5 Utility Call Key Setting

„

Utility call key setting function

The key position for calling the main menu of the utility can be specified.

For the key position, 0 or 1 point can be specified from 4 corners on the screen.

By keeping pressing the screen, a setting to switch the screen to the utility is available.

This prevents a switching to the utility by an unintentional operation.

9

10

Operation setting by GT Designer3

Select [Common Settings] [GOT Environment Settings] [GOT Setup] from GT Designer3 to make the settings of the utility call key.

To change a part of the setting after downloading the project data, change the setting at the display setting of GOT.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

11

„

Display operation of Utility call key

(

Main menu

9.3 Utility Display)

GOT setup

Operation

12

Touch

[GOT setup]

Touch

[Operation]

Touch

[Utility call key]

13

Menu call key

14

Touch buttons to set for the utility call key

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11 - 11

„

Setting operation of utility call key

1.

Touch

●

or displayed at the 4 corners of the setting screen. The button repeats

● with every touch. Set the corner to be set to a key position to

●

.

For the key position, 0 or 1 point only can be set.

2.

When setting 1 point, specify the time to switch to the utility in case of keeping pressing the key position.

Touch the time input area.

3.

Touching the input area displays a keyboard.

Input numerical value from the keyboard.

4.

Touching [OK] button defines the setting contents.

Touching [ ] button returns the screen to the

[Operation] screen.

(1) When the utility call key is set to the zero point

Even when the utility call key is set to the zero point, you can display the main menu using either of the following two operations:

• Pressing the special function switch set on the user-created screen

• Keeping pressing the upper left corner while the [Booting.] message is displayed after powering up.

9.3.1 Display operation of main menu

(2) Precautions on using the advanced alarm popup display

When [Display Position Switching] is set to [Switch] in the advanced alarm popup display setting, set either of the following for the utility call key.

• Setting the position of the utility call key to the upper-right or lower-left corner

• Setting [Pressing Time] of the utility call key to 1 or more seconds

When [Pressing Time] is set to 0 and the key position is set to the lower-left corner, the operation is as described below. If the positions of the key and the advanced alarm popup display overlap, the utility screen appears by switching the display position of the advanced alarm popup display.

For the advanced alarm popup display, refer to the following.

GT Designer3 Version1 Screen Design Manual (Functions)

(3) When limiting the display and operation of the utility

When limiting the display and operating users, set a password to the GOT using the GT Designer3. If a user tries to display the main menu of the utility, the password input screen is displayed.

For details on setting passwords, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

11 - 12

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11.2.6 Adjusting the touch panel position (Touch panel calibration)

„

Touch panel calibration setting function

Touch panel reading error can be corrected.

Normally the adjustment is not required, however, the difference between a touched position and the object position may occur as the period of use elapses.

When any difference between a touched position and the object position occurs, correct the position with this function.

Before adjustment After adjustment

9

10

Run Stop Run Stop

11

The [Run] will operate though you intended to touch the [Stop] button.

„

Display operation of Touch panel calibration

The [Stop] button can be touched without fail.

(

Main menu

9.3 Utility Display)

GOT setup

Operation

12

Touch

[GOT setup]

Touch

[Operation]

13

Touch

[Touch panel calibration]

Touch panel calibration

14

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11 - 13

„

Touch panel calibration operation

Touch the point displayed on the screen with the finger one by one to make the setting.

1.

Touch the center of the displayed on the upper left precisely.

2.

Touch the point displayed on the upper right.

3.

Touch the point displayed on the lower left.

4.

Touch the point displayed on the lower right.

5.

Touching the button displayed on the upper right returns the screen to the previous screen.

When the precise touch could not be made, touch the [Readjustment] button to make the setting from

again.

11 - 14

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11.2.7 USB mouse/keyboard setting

„

Function of USB mouse/keyboard

To install and use the USB mouse/keyboard on the GOT, set the USB mouse/keyboard.

„

Display operation of USB mouse/keyboard

(

Main menu

9.3 Utility Display)

GOT setup

Operation

Touch

[GOT setup]

Touch

[Operation]

Touch

[USB mouse/keyboard]

USB mouse/keyboard

9

10

11

12

13

„

USB mouse/keyboard setting operation

1.

To use the USB mouse, touch the setting item of

[Use USB mouse].

The setting content is changed by touching.

14

15

(Continued to next page)

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11 - 15

2.

To move the mouse cursor to the touched position, touch the setting item of [Interlock with mouse cursor touch operation].

The setting content is changed by touching.

3.

To use the USB keyboard, touch the setting item of

[Use USB keyboard].

The setting content is changed by touching.

4.

To use the USB keyboard, touch the setting item of

[USB keyboard type].

The setting content is changed by touching.

(Japanese 106 keyboard English 101 keyboard)

5.

Touching [OK] button defines the setting contents.

Touching [ ] button returns the screen to the

[Operation] screen.

11 - 16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.2 Operation Setting (Settings Regarding Operation)

11.3 Transparent Mode Setting

„

Function of the transparent mode

When using the multi-channel function, the channel No. of a controller to which the FA transparent function is executed can be specified. For the multi-channel function and FA transparent function, refer to the following manual.

GOT1000 Series Connection Manual (Mitsubishi Products) for GT Works3

Function

Ch No.

Description

The channel No. of a controller to which the FA transparent function is executed can be set.

Setting range

1/2

(Default: 1)

„

Display operation of Transparent mode

(

Main menu

9.3 Utility Display)

GOT setup

9

10

11

Touch

[GOT setup]

Touch

[Transparent mode]

12

Transparent mode

13

„

Setting operation of transparent mode

14

1.

Touching the transparent Ch No. (numerical part) on the left displays the screen to select the communication driver.

Select the channel to execute the FA transparent function.

2.

Touching [OK] button defines the setting contents.

Touching [ ] button returns the screen to the [GOT

Setup] screen.

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.3 Transparent Mode Setting

11 - 17

11.4 Backup/Restoration Setting

The storage location for backup data can be set.

For how to use the backup/restoration, refer to the following manual.

GOT1000 Series Extended/Option Functions Manual for GT Works3

Set the following items with touching the items on the GOT.

Item

Drive for backup setting

Drive for backup data

Trigger backup setting

Max. of backup data

The drive for storing backup settings, including parameters and passwords for controllers, can be selected.

Description

The drive for storing backup data can be selected.

The GOT automatically backs up data when triggers (Rise, Time) specified for each backup setting are met.

Set the maximum number of backup data to be stored.

(When 0 is specified, the GOT does not check the number of backup data to be stored.)

Setting range

A: Built-in SD Card

E: USB memory

(Default: A: Built-in SD Card)

A: Built-in SD Card

E: USB memory

(Default: A: Built-in SD Card)

None/Rise/Time

(Default: None)

Setting range: 0 to 50

(Default: 10)

„

Display operation of Backup/restoration setting

(

Main menu

9.3 Utility Display)

GOT setup

Touch

[GOT setup]

Touch

[Backup/restoration setting]

Backup/restoration setting

11 - 18

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.4 Backup/Restoration Setting

9

„

Setting operation of backup/restoration setting

(1) Drive for backup setting, drive for backup data

1.

Touching the setting item changes the setting items.

10

2.

Touching [OK] button defines the setting contents.

Touching [ ] button returns the screen to the [GOT

Setup] screen.

11

(2) Trigger backup settings

For operations of the trigger backup setting, refer to the following.

■

Trigger backup settings

(3) Max. of backup data

1.

Touching the setting items displays the keyboard.

Input numerical value from the keyboard.

Setting range: 0 to 50, Default: 10

(When 0 is specified, the GOT does not check the number of backup data to be stored.)

2.

Touching [OK] button defines the setting contents.

Touching [ ] button returns the screen to the [GOT

Setup] screen.

12

13

14

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.4 Backup/Restoration Setting

11 - 19

„

Trigger backup settings

When the conditions of the trigger specified for each backup setting (Rise, Time) are met, the GOT automatically backs up data.

How to use the trigger backup, refer to the following manual.

GOT1000 Series Extended/Option Functions Manual for GT Works3

„

Display operation of Trigger backup setting

1.

Touching a setting item for the trigger type changes the setting.

(None Rise Time)

None

Rise

Time

: The GOT does not execute the trigger backup.

: The GOT backs up data when the trigger device turns on.

: The GOT backs up data at the specified time.

2.

Touching a setting item for [Check the file register changes] changes the setting.

Execute

Not execute

: When the backup is executed, the GOT checks if data stored in file registers are changed after the previous backup. When the data are changed, the GOT backs up the changed data.

: When the backup is executed, the GOT does not back up data stored in file registers even if the data are changed after the previous backup.

3.

When the trigger type is changed, the setting is defined by touching the [OK] button.

Touching [ ] button returns the screen to the backup/ restoration setting screen.

4.

When the trigger type is set to [Time], touching a setting item for [Detail] switches the screen to the trigger time setting screen.

In the screen, specify the days and time that the

GOT executes the backup.

Day

Time

: Select days that the GOT executes the backup by touching displayed items.

Multiple days can be selected.

: Set the time that the GOT executes the backup by touching the displayed item.

Precautions for setting

When the trigger type is set to [Rise], set the trigger device with GT Designer3 in advance.

Failure to do so disables the backup setting with [Rise] set.

11 - 20

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.4 Backup/Restoration Setting

11.5 Behavior of Duplicate IPs

„

Setting function for Behavior of duplicate IPs

The GOT operation can be set when a device with the same IP address as that of the GOT is added to the network afterwards.

Function

Behavior of duplicate IPs

Description

The GOT operation can be set when a device with the same IP address as that of the GOT is added to the network afterwards.

Setting range

Maintain a network connection(rec)

/Do not maintain a network connection

(Default: Maintain a network connection (rec))

9

10

(1) When the IP address duplication is not checked

When the IP address of the GOT is set to 192.168.0.18, the IP address duplication check is not performed.

Depending on the device to connect with the GOT, the IP address duplication check may not be performed.

(2) When the GOT is added to the network in which a device with the same IP address as that of the GOT exists

The GOT goes into offline status and displays the following dialog box.

11

12

13

• When changing the IP address of another device which has the same IP address as that of the GOT

After changing the IP address of another device which has the same address as that of the GOT, touch the

[Reboot GOT] button to restart the GOT.

• When changing the IP address of the GOT

Touch the [Clear IP Address] button to clear the IP address of the GOT.

After touching the [Reboot GOT] button to restart the GOT, change the IP address of the GOT using the

Utility.

14

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.5 Behavior of Duplicate IPs

11 - 21

„

Display operation of Behavior of duplicate IPs

(

Main Menu

9.3 Utility Display)

GOT setup

Touch

[GOT setup]

Behavior of duplicate IPs

Touch

[Behavior of duplicate IPs]

„

Setting operation of Behavior of duplicate IPs

1.

Touching the setting item changes the setting items.

• Maintain a network connection (rec):

The GOT stays connected to the network when a device with the same IP address as that of the

GOT is added to the network afterwards.

A system alarm occurs.

• Do not maintain a network connection:

The GOT is disconnected from the network when a device with the same IP address as that of the

GOT is added to the network afterwards.

2.

Touching [OK] button defines the setting contents.

Touching [ ] button restarts the GOT and reflects the setting contents.

11 - 22

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.5 Behavior of Duplicate IPs

9

(1) Precautions for selecting [Do not maintain a network connection]

When selecting [Do not maintain a network connection], the GOT is disconnected from the network at the addition of a device with the same IP address as the GOT.

Therefore, there is a possibility that the running GOT cannot be communicated by IP address setting mistakes or intended actions by malicious users, and the system control may be influenced by those errors.

Please change the setting of [Behavior of duplicate IPs] after carefully examining the necessity.

(2) Precautions for using a switching hub compatible with the spanning tree protocol

For the switching hub port connected with the GOT, configure the setting (PortFast or others) that makes the

GOT be ready for communications (forwarding state). The setting is required to make sure that the delay right after the connection by the spanning tree protocol does not occur.

Without the setting, the Ethernet IP address duplication is not correctly detected.

Additionally, the GOT may not be connected to Ethernet correctly.

For the setting that makes the GOT be ready for communications (forwarding state), refer to the user’s manual for the switching hub used.

10

11

12

13

14

15

16

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.5 Behavior of Duplicate IPs

11 - 23

11 - 24

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

11.5 Behavior of Duplicate IPs

12. CLOCK SETTINGS AND BATTERY

STATUS DISPLAY

(TIME SETTING AND DISPLAY)

10

Setting items for clock display can be displayed from the GOT utility screen.

12.1 Time Setting and Display

12.1.1 Time setting and display functions

Time settings and displaying of the status of GOT built-in battery are possible.

Function

Clock setting

Clock display

GOT internal battery voltage status

Description

Setup the method to adjust the time between GOT clock data and clock data of PLC CPU connected with GOT.

Carry out the display and setup of GOT clock data.

Displays GOT internal battery voltage status.

Reference

12-2

12-3

12-3

11

12

9

Changing times

When the time is changed on the Time setting & display screen, the changed time is written in a programmable controller even though [Adjust] or [Broadcast] is set for [Time setting].

As a result, the time of the programmable controller can be changed on the GOT even though [Adjust] is set for

[Time setting].

(The clock data of the controller set as [Adjust CH No.] of [Time setting] in [GOT Setup] ([Clock Setting]) from [GOT

Environment Settings]of GT Designer3 is changed.)

For details of [Adjust] and [Broadcast], refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

13

14

„

Display operation of time setting

Main menu

(

9.3 Utility Display)

Time setting & display

15

Touch

[Time setting & display]

Set the Time setting and Clock setting

16

12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)

12.1 Time Setting and Display

12 - 1

„

Operation of time setting

(1) Clock setting

Setup the method to adjust the time between GOT clock data and the clock data of controller connected to the

GOT.

It is same as set in the GOT setup in Environmental Setting of GT Designer3.

Setting

GT Designer3 Version1 Screen Design Manual (Fundamentals)

Description

Adjust the time of GOT clock data to the clock data of controller.

Adjust

Adjust the time of controller clock data to the GOT clock data.

Broadcast

Adjust the GOT and controllers to the controller whose clock data is used as a base.

Adjust/Broadcast

None No adjustment of clock data.

1.

Touching the setup item changes the setup contents.

Adjust Broadcast Adjust/Broadcast None

2.

Touching [OK] button reflects the setup contents.

Touching the [ ] button restarts the GOT.

After restarting, the GOT operates with the changed setting.

12 - 2

(1) When connecting with an external device which does not have clock function.

If set to [Adjust] or [Broadcast] for [Clock setting] while the GOT is connected with external devices (PLC or microcomputers) which do not have clock function, the clock data will not be adjusted.

For the list of PLC installed with clock function, refer to the following.

GOT1000 Series Connection Manual for GT Works3

(2) Setting of clock setting and battery

The connector of the GOT is not connected to the battery connector at purchase.

When selecting [Broadcast] or [None] in clock setting, set the clock of the GOT once with connecting a battery to the GOT.

(3) Operation setting by GT Designer3

Carry out the setting of clock setting in [GOT set up] in [Environmental Setting] of GT Designer3.

To change a part of the setting after downloading the project data, change the setting at the display setting of

GOT.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)

12.1 Time Setting and Display

(2) Clock display

Carry out the display and setting of GOT clock data.

The setup methods of clock data are shown below.

1.

Touching the clock display section displays the keyboard for input and stops the clock update.

2.

Input time with the keyboard by referring to the table below.

Input the scheduled time when the operation of is to be carried out since the input time is reflected at the time of the operation of .

The day of the week is displayed automatically according to the input date.

The effective range of clock setting is as follows.

Jan. 1, 2000 to Dec. 31, 2037

9

10

11

Key

0

to

9

/

Del

Enter

Cancel

Description

Input numeric value in cursor position.

Move the cursor.

Move the cursor to the left by one character when [Del] Key is touched while inputting year, month, day, time, minutes, seconds.

Carry out nothing when touched other than when inputting the above.

Close the keyboard after the input time is displayed in clock display.

The update of the clock display does not restart even if the keyboard is closed.

The update of the clock display restarts with the operation of .

Cancel the input time and returns the time of clock display to the time at which the keyboard was displayed and close the keyboard.

The update of the clock display does not restart even if the keyboard is closed.

The update of the clock display restarts with the operation of .

3.

Touching the [OK] button reflects the settings and restarts updating the clock display.

Then, the settings are reflected to both clock data on the GOT and controller.

Touching [ ] button restarts the GOT if the clock settings is changed, or closes the screen if clock settings is not changed.

12

13

14

(3) GOT internal battery voltage status

Displays battery voltage status.

Display

Normal

Low/None

When the battery voltage is low, replace the battery immediately.

For battery replacement procedure, refer to the following.

Status

Normal

Low voltage

8.3.3 Battery replacement procedure

15

16

12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)

12.1 Time Setting and Display

12 - 3

12 - 4

12. CLOCK SETTINGS AND BATTERY STATUS DISPLAY (TIME SETTING AND DISPLAY)

12.1 Time Setting and Display

13. FILE DISPLAY AND COPY

(PROGRAM/DATA CONTROL)

The display of OS, project data or alarm data which is written in the GOT or SD card and the data transmission between

GOT and SD card/USB memory are possible.

The format of the SD card/USB memory is also possible.

13.1 Data Storage Location

10

13.1.1 Data type and storage location

„

System

The data storage location and transferring (write/read) route for each data type are shown below.

Also, the data storage locations are shown below.

OS

BootOS

Project data Write

C drive

(Built-in flash memory)

Read

Project data

PC

GT Designer3

OS BootOS

Project data

Install/

Download

Upload

OS

BootOS

Project data

Copy files on

Windows

Project data

Write

BootOS

Project data

A drive

(Built-in SD card)

E drive

(USB drive)

11

12

13

Inserting/

Removing

SD card

(when installed in GOT)

USB memory

(when installed in GOT)

SD card

(when installed in PC)

USB memory

(when installed in PC)

Install, Write :

Upload, Read :

The data of the Flash Memory (Project data, etc.) can be saved even if the battery voltage becomes low.

Item Data type Storage location

BootOS

BootOS Built-in flash memory (C drive)

OS

*1

Project data

*1

*1

*2

Standard monitor OS

Communication driver

Extended function OS

Option OS

Built-in SD card (A drive)

Built-in flash memory (C drive)

*2

Project data

(Including recipe setting, alarm conditions, time action, and GOT setup.)

Built-in SD card (A drive)

Built-in flash memory (C drive)

*2

The USB memory can be used from Utility.

16.3.2 Installing using the program/data control function (Utility)

When using the project data stored in the built-in SD card (A drive) with the GOT, hold the SD card installed to the GOT. The USB memory cannot be activated directly from the E drive. It can be used only for data storage.

14

15

16

9

13 - 1

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.1 Data Storage Location

„

At maintenance

C drive

(Built-in flash memory)

Copy

Alarm

Hard copy

D drive

(Built-in SRAM)

Copy

Alarm

Hard copy

A drive

(Standard CF card)

E drive

(USB drive)

Read

Alarm

Hard copy

Recipe

Logging

PC

GT Designer3

Copy files on

Windows

SD card

(when installed in GOT)

USB memory

(when installed in GOT)

Alarm

Item

Recipe

Logging

Hard copy

Data type

Alarm data (Extended alarm log file and alarm log file)

Recipe data (Advanced recipe file, Recipe file)

Logging (Logging file)

Image file (Hard copy function)

*1 The USB memory can be used from Utility.

Alarm

Hard copy

Recipe

Logging

Inserting/

Removing

SD card

(when installed in PC)

USB memory

(when installed in PC)

Install, Write :

Upload, Read :

Storage location

Built-in SD card (A drive)

Internal SRAM (D drive)

USB drive (E drive)

*1

Checking the available memory of storage location

When saving resource data, check available memory of storage location before use.

Memory capacity of internal SRAM (D drive) is 512kbytes. Use the built-in SD card (A drive) if the available memory is not enough.

13 - 2

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.1 Data Storage Location

13.1.2 OS version confirmation

9

Confirm the OS version carefully when install BootOS and Standard monitor OS.

When OS is installed, GOT checks and compares the OS version automatically.

(1) When install BootOS

When the BootOS to be installed has the older major version, GOT displays the installation disapproving message to cancel the installation so that the older version may not be written.

(Even when the version of the BootOS to be installed has the same or later version, the version information and the dialog for selecting continue/not continue will be displayed.)

Depending on the Installation method, the dialog box to be displayed varies.

• When installing from the built-in SD card, the dialog box is displayed by the main unit.

• When installing from GT Designer3 via USB or Ethernet, the dialog box is displayed by the GT Designer3

(2) When install Standard monitor OS, communication driver, Option OS

When Standard monitor OS, communication driver, or Option OS has already been installed, the version information of the OS which has been installed and the dialog for selecting continue/not continue will be displayed.

Moreover, when the different versions will coexist among all OSs (Standard monitor OS, communication driver, and Option OS) by installing OS, the installation disapproving dialog will be displayed and the installation process is canceled.

(3) When download project data

GOT automatically compares the version between the project data to be downloaded and the installed OS.

When the versions are different, the dialog confirming whether to install the OS together is displayed.

When downloading the project data from the SD card or USB memory, storing the project data and OS beforehand is recommended.

The version of each OS installed in the GOT can be confirmed by [Property] of [OS information] screen.

10

11

12

13

Explanation of OS version

01.00.00.A

BootOS version

(Appears only when the property

of the BootOS is displayed.)

Minor version

Major version

14

For details of the screen display operation, refer to the following.

13.2.1 OS information

15

Version confirmation of BootOS by rating plate

Check the version of BootOS installed in GOT at product shipment on the rating plate on GOT rear face.

When the Boot OS version is 2 digits, only the lower digit is printed.

AA

BootOS

Version

HD

BootOS

Version

Example H/W version: H

Boot OS version: AD

Rating plate: HD

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.1 Data Storage Location

13 - 3

13.1.3 Capacity confirmation of the project data downloading location

When download the project data, confirm the capacity of the user area in the drive to which transferred, the transferred project data size, the transfer size and buffering area size of the optional function OS in advance to judge whether to carry out the download.

The capacities can be confirmed by GT Designer3. For details, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

13.1.4 Display file

The display screen and storage destination for each type of data are shown below.

The file name and contents of each data can be displayed with property display of the utility

Item Display screen

BootOS

Storage destination (Drive name/folder name)

A drive/C drive/E drive

: \G1BOOT\

*2

Standard monitor OS

Standard monitor OS system screen data

Standard monitor OS system screen management information file

Standard monitor OS (monitor function)

6 8-dot font (ASCII characters)

24-dot numerical HQ font

32-dot numerical HQ font

TrueType numerical font

12-dot standard font

16-dot standard font

OS information screen

A drive/C drive/E drive

*3

: \G1SYS\

*2

Extended function OS

Option OS

Communication driver

Project data

*1

Resource data

User-created screen data

Comment data

12-dot HQ fonts (Mincho/Gothic)

16-dot HQ fonts (Mincho/Gothic)

TrueType (Mincho/Gothic)

Advanced alarm log file CSV file

*5

Advanced alarm log file TXT file

*5

Advanced alarm log file binary file

*5

Alarm log file CSV file

*5

Hard copy file BMP file

*5

Hard copy file JPG file

*5

Advanced recipe file CSV file

*5

Advanced recipe file TXT file

*5

Advanced recipe file binary file

*5

Logging file CSV file

*5

Logging file TXT file

*5

Logging file binary file

*5

Project information screen

Alarm information screen

Hard copy information screen

Advanced recipe information screen

Logging information screen

A drive/C drive/E drive

:\PROJECT1\

*2*4

A drive/D drive/E drive

: \

*3

With GT Designer3, any folder name or file name can be specified.

*2

*6

*1 The user-created screen data, comment data, and font data are displayed as project data.

*2 Each folder is created automatically when a file is installed, downloaded, or uploaded.

*3 The USB memory cannot be activated directly from the E drive. It can be used only for data storage.

13.2.1 OS information

*4 The folder names and file names can be set at [System Settings] in [System Environment] of GT Designer3.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

*5 A serial number is automatically added to file names.

*6 Each function does not provide direct storage to the E drive.

13 - 4

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.1 Data Storage Location

13.2 Various Data Control

9

13.2.1 OS information

„

Function of OS information

Each file name/folder name of BootOS and OS (Standard monitor OS, PC communication driver and Option OS) by which each drive (A: Built-in SD card, C: Built-in flash memory, E: USB memory) holds can be displayed in lists.

Installation and uploading of the files are also possible.

Function

Displaying file, folder data

Reference

13-6, 13-7

Install

Upload

Property display

Data check

Description

The file/folder type, name, data size and creating date & time are displayed.

All OS files written in the A drive (Built-in SD card)/E drive (USB drive) can be installed in the C drive (Built-in flash memory).

All OS files in the C drive (Built-in flash memory) can be uploaded to the A drive (Built-in SD card)/

E drive (USB drive).

Displays the property (file name, data size, type, version and creation date) of the file.

Data check of files is possible.

13-8

13-9

13-10

13-10

10

11

(1) Notes on installing OS

If the Boot OS or the Standard monitor OS is installed, such data on the GOT as the project data will be deleted.

After installing the Boot OS or the Standard monitor OS, reinstall/download necessary data.

(2) Notes on handling OS files

When the OS boot drive is set to [A: Built-in SD card], installing and uploading OS files are not available.

„

Display operation of OS information

(

Main menu

9.3 Utility Display)

Program/Data control

Touch

[OS information]

Touch

[Program/data control]

OS information

12

13

14

15

Select a drive and operate BootOS and OS files

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 5

„

Display example of OS information

OS information OS information Storage file/folder display screen

(2)

(3) (4)

(7)

(8)

(5)

(6)

(9)

(1)

Number

(1) Select drive

Item

(2) Kind

(3) Name

(7)

(8)

(9)

(4)

(5)

(6)

Path name

Size

Date and time

The size of drive

Operation switch

Number of files

Description

The target drive which displays file or folder can be selected.

When the SD card is not installed, [A:Built-in SD card] is not displayed.

If the USB memory is not installed, [E: USB drive] is not displayed.

Indicates the type of the displayed name (file or folder).

In case of file, displays the extension; in case of folder, displays "DIR".

The file name or folder name which is stored in the selected drive or folder is displayed.

When the file name or folder name exceeds 20 characters, the exceeding characters (the 21st character or after) are not displayed.

Displays the path name of drive/folder which is currently displayed.

Displays the size of the file displayed in [Name].

The date and time when each file was created are displayed.

Displays the size in use and the entire size of the drive which is selected by drive selection.

(Only the size in use is displayed when selecting the C drive.)

Execution switch of each function.

Displays the total number of the displayed files.

Folders and files displayed

For the folders and files displayed, refer to the following.

13.1.4 Display file

13 - 6

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

OS information operation

(1) Display operation of OS information

9

1.

Touching a drive in [Select drive] displays the information of the first folder of the touched drive.

2.

Touching a folder name displays the information of the touched folder.

3.

Touching a folder name of [ . . ] displays the information of the folder in one upper hierarchy.

4.

Touching button of the scrollbar scrolls up/ down the screen by one line.

Touching one screen.

button scrolls up/down the screen by

5.

Touching a file name selects and inverts the file.

6.

For operation of installation, upload, property, data check, refer to the following.

Install.................

Upload...............

Property.............

Data check.........

This section (2)

This section (3)

This section (4)

This section (5)

7.

[Touching [ ] button closes the screen.

10

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 7

(2) Installation operation

BootOS and OS which are written in the A drive (built-in SD card) or E drive (USB drive) can be installed in GOT.

(This item explains using the A drive.)

1.

Install the SD card to which the BootOS or OS to install is written to the GOT.

For inserting/removing method of SD card/USB memory, refer to the following.

8.1.2 Installing and removing procedures of the SD card

8.2.2 Installing and removing procedures of the USB memory

2.

Touch [A: Built-in SD card] of [Select drive].

3.

Touching [Install] button starts the install.

4.

When the installation is completed, the dialog shown left is displayed.

Touching [OK] button restarts GOT.

13 - 8

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(3) Upload operation

BootOS and OS in the C drive (Flash Memory) can be uploaded to the A drive (Built-in SD card) and E drive

(USB drive).

The SD card after uploading can be used for installing the OS on another GOT.

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

(This item explains using the A drive.)

1.

Install the SD card used as the uploading destination to GOT.

For inserting/removing method of SD card/USB memory, refer to the following.

8.1.2 Installing and removing procedures of the SD card

8.2.2 Installing and removing procedures of the USB memory

2.

Touch [A: Built-in SD card] of [Select drive].

9

10

11

12

3.

Touching [Upload] starts the uploading.

4.

When the upload is completed, the dialog shown left is displayed.

Touching [OK] button closes the dialog.

15

16

13

14

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 9

(4) Property display operation

Displays the property of the file stored in the selected folder.

1.

Touching [Property] button after selecting the property displaying target folder displays the

[Property] screen shown left.

In the [Property] screen, the following information is displayed for each file selected by .

Item

Name

Size

Kind

Version

Date, Time

Description

Displays the file name.

Displays the file size.

Displays the following items according to the kind of the files.

Boot: BootOS

Basic: Standard monitor OS

Extend: Extend function OS

Option:Optional function OS

Comm.:Communication driver

Displays the version of BootOS and OS.

Displays the date and time of the file creation.

2.

Touching button of the scrollbar scrolls up/ down the screen by one line.

Touching by one screen.

button scrolls up/down the screen

3.

Touching [ ] button returns the screen to the previous screen display.

(5) Data check operation

Carries out data check of the selected system file.

When data is normal.

1.

Touch [Data check] button after selecting a data check target file. The dialog mentioned left will be displayed after executing data check.

2.

Touching [OK] button closes the dialog.

When data is erroneous.

13 - 10

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.2 Alarm information

„

Function of alarm information

The extended alarm log file or alarm log file held by each drive (A: Built-in SD card, C: Flash Memory, D: Internal

SRAM, E: USB drive) is displayed.

The functions below can be carried out for files.

The USB drive only stores log files, and cannot be displayed.

For details of Advanced Alarm, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Functions)

Function

Displaying file, folder data

Description

The file/folder name, data size and creating date & time are displayed.

Reference

13-12, 13-13

G1A CSV conversion

G1A

Delete

TXT conversion

Copy

Converts the G1A file of advanced alarm log file to CSV file.

Converts the G1A file of advanced alarm log file to TXT file.

File is deleted.

File is copied.

13-14

13-14

13-15

13-16

„

Display operation of Alarm information

(

Main menu

9.3 Utility Display)

Program/data control

9

10

11

12

Touch

[Alarm information]

Touch

[Program/data control]

13

Alarm information

14

Select a drive and operate alarm log files

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 11

„

Display example of Alarm information

Alarm information screen Alarm information: Storage file/folder display screen

(2) (3)

(7)

(4)

(5)

(8)

(6)

(9)

(1)

Number

(1) Select drive

Item

(2) Kind

(3) Name

(7)

(8)

(9)

(4)

(5)

(6)

Path name

Size

Date and time

The size of drive

Operation switch

Number of files

Description

The target drive which displays file or folder can be selected.

When SD card or USB memory is not installed, the following drives are not displayed.

• SD card: [A: Built-in SD card]

• USB memory: [E: USB drive]

Indicates the type of the displayed name (file or folder).

The file is indicated with an extension, while the folder is indicated with "DIR."

(

Displays the file name or folder name.

For the long file/folder name, entire part may not be displayed.

Confirm the nondisplayed part with the [Copy] button, etc.

13.2.2

■

Alarm information operation(4)Copy operation)

After confirmation, touch the [Cancel] button to cancel the operation.

Displays the path name of drive/folder which is currently displayed.

Displays the size of the file displayed in [Name].

The date and time when each file was created are displayed.

Displays the size in use and the entire size of the drive which is selected by drive selection.

(Only the size in use is displayed when selecting the C drive.)

Execution switch of each function.

Displays the total number of the displayed files.

(1) Display of creation date and time

The creation date and time display is not updated even if a file is created or updated while displaying the alarm information display screen.

If close the screen currently displayed (moving the screen to the folder of the upper hierarchy, etc.) and display the screen again, the updated contents are displayed.

(2) Folders and files displayed

For the folders and files displayed, refer to the following.

13.1.4 Display file

13 - 12

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

Alarm information operation

(1) Display operation of Alarm information

Alarm information screen

Alarm information: Storage file/folder display screen

9

1.

Touching a drive of [Select drive] displays the information of the touched drive.

2.

Touching a folder name displays the information of the touched folder.

3.

Touching a folder of [ . . ] displays the information of the folder of the one upper hierarchy.

4.

Touching button of the scrollbar scrolls up/ down the screen by one line.

Touching one screen.

button scrolls up/down the screen by

5.

Touching a file name selects the file.

6.

For G1A CSV, G1A TXT, delete, copy, graph operations, refer to the following.

G1A CSV, G1A TXT........

Delete.......................................

Copy.........................................

This section (2)

This section (3)

This section (4)

7.

Touching [ ] button closes the screen.

10

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 13

(2) G1A CSV conversion operation, G1A TXT conversion operation

The selected G1A file is converted to CSV file or TXT file.

1.

Touch and select the G1A file to convert into a CSV file or a TXT file.

(Example: When [G1A CSV] button is touched)

2.

The following dialog box is displayed when touching the following button according to the file type to convert to.

• CVS file: [G1A CSV] Button

• TXT file: [G1A TXT] Button

3.

Touch [OK] button.

When the file, whose name is the same, exists in the destination folder, the dialog box shown at left appears without starting the conversion.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the conversion.

4.

The message of completion is displayed in dialog box when conversion is completed.

Touching [OK] button closes the dialog.

13 - 14

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(3) Deletion operation

Deletes selected files.

9

1.

Touch and select the file to delete.

2.

Touching [Delete] button displays the dialog mentioned left.

Touching [OK] button deletes the file.

Touching [Cancel] button cancels the deletion.

10

3.

When the deletion is completed, the completion dialog is displayed.

Touching [OK] button closes the dialog.

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 15

(4) Copy operation

Copies the selected file.

Dialog for selecting a copy destination drive

1.

Touch and select the file to copy.

2.

Touching [Copy] button displays the message

[Please select a destination.] in the left bottom of the screen.

3.

If the copy destination folder is touched, the screen display is changed to the folder of copy destination.

At this time, it cannot be copied into the same folder where the file exists.

Select other folders.

4.

Touching [Exec.] button displays the dialog box shown left.

5.

Touch [OK] button.

If there is a file of the same name in the copy destination folder, the following dialog is displayed without starting the copy.

6.

When the copy is completed, the dialog of completion is displayed.

Touching [OK] button closes the dialog.

13 - 16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.3 Project Information

„

Function of project information

The project data files stored in each drive (A: Built-in SD card, C: Flash Memory, E: USB memory) can be displayed by lists.

In addition, the files can be downloaded, uploaded, deleted or copied, etc.

Function

Displaying file, folder data

Delete

Copy

Property display

Data check

Download

Setup

Upload

Setup cancel

Description

The file/folder type, name, data size and creating date & time are displayed.

Deletes project data.

Copies project data. (can copy the A drive and E drive)

Displays the project data creation date, author name and the version of GT Designer3.

Data check of files is possible.

Downloads the project data written in the A drive (Built-in SD card)/E drive (USB drive) to C drive

(Flash Memory).

The project data to be displayed can be selected.

Uploads the project data written in the C drive (Flash Memory) to the A drive (Built-in SD card)/E drive (USB drive).

Cancels the item which is selected for the project data to be displayed.

Reference

13-18, 13-19

13-19

13-20

13-21

13-22

13-22

13-24

13-25

13-26

9

10

11

12

Notes on operating project data

When the OS boot drive is set to [A: Built-in SD card], deleting, copying, downloading, setting up, and uploading project data are not available.

„

Display operation of Project information

(

Main Menu

9.3 Utility Display)

Program/Data control

13

Touch

[Program/data control]

Touch

[Project information]

14

Project information

15

Select a drive and operate project data files

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 17

„

Display example of Project information

Project information

Project information

Storage file/folder display screen

(2)

(7)

(3) (4)

(8)

(5) (6)

(9)

(1)

Number

(1) Select drive

Item

(2) Kind

(3) Name

(4)

(5)

(6)

(7)

Path name

Size

Date and time

The size of drive

(8)

(9)

Operation switch

Number of files

Description

The drive by which a file or folder is displayed can be selected.

When the SD card is not installed, [A:Built-in SD card] is not displayed.

If the USB memory is not installed, [E: USB drive] is not displayed.

Indicates the type of the displayed name (file or folder).

The file is indicated with an extension, while the folder is indicated with "DIR."

Displays the project data (Project Folder) in the selected drive.

When the name exceeds 18 characters, the 19th and later characters are not displayed.

The project data being monitored on the GOT is preceded by "%".

Displays the path name of drive/folder which is currently displayed.

Displays the size of the file displayed in [Name].

Displays the date and time when each file is installed.

Displays the size in use and the entire size of the drive which is selected by drive selection.

(Only the size in use is displayed when selecting the C drive.)

Displays the execution switch of functions (download, upload, etc.) which can be carried out in [Project information].

Displays the total number of the displayed files.

Folders and files displayed

For the folders and files displayed, refer to the following.

13.1.4 Display file

13 - 18

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

Operation of project information

(1) Display operation of Project information

9

1.

Touching a drive in Select drive displays the project data in the drive.

2.

Touching project data selects and inverts it.

3.

For operation of delete, copy, property, data check, download, upload, refer to the following.

Delete.......................................

Copy.........................................

Property....................................

Data check...............................

Download, setup

..................................................

Upload, setup cancel

..................................................

This section (2)

This section (3)

This section (4)

This section (5)

This section (6)

This section (7)

4.

Touching [ ] button closes the screen.

10

11

12

(2) Deletion operation

Deletes selected files.

1.

Touch and select the file to delete.

2.

Touching [Del] button displays the screen mentioned left.

Confirm the deletion targeted file is specified correctly.

Touching [OK] button deletes the file.

Touching [Cancel] button cancels the deletion.

13

14

3.

When the deletion completes, the dialog box shown left is displayed.

Touching [OK] button closes the dialog.

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 19

(3) Copy operation

Uploads the project data written in the C drive (Flash Memory) to the A drive (Built-in SD card)/E drive (USB drive).

• Copying to another directory in the same drive

• Copying between A drive and E drive

Copy to/from C drive or copy to C drive/D drive is disabled.

(This item explains using the A drive.)

Dialog for selecting a copy destination folder

1.

Install SD card in the PC, in which create a folder for the copy destination.

Set the same character with [System Setting] of

[System Environment] of GT Designer3 for the folder name.

GT Designer3 Version1 Screen Design Manual

(Fundamentals)

2.

Install the SD card mentioned above to GOT.

For inserting/removing method of SD card/USB memory, refer to the following.

8.1.2 Installing and removing procedures of the SD card

8.2.2 Installing and removing procedures of the USB memory

3.

Open [Project Information] screen to select the file to copy.

4.

Touching [Copy] button displays the message

[Please select a destination.] in the left bottom of the screen.

5.

If the copy destination folder is touched, the screen display is changed to the folder of copy destination.

At this time, it cannot be copied into the same folder where the file exists.

Select other folders.

6.

Touching [Exec.] button displays the dialog box shown left.

13 - 20

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

7.

Touch [OK] button.

If there is no file of the same name in the copy destination folder, starts to copy.

When there is a file of the same name in the copy destination folder, the dialog mentioned left is displayed without starting the copy.

If copy, in this case, the copied file is overwritten to the project data in the copy destination folder.

Touching [OK] button starts copy.

Touching [Cancel] button cancels the copy.

8.

When the copy is completed, the dialog of completion is displayed.

Touching [OK] button closes the dialog.

9

10

11

12

(4) Property display operation

Displays the property of the project data in the selected folder.

1.

Touching [Property] button after selecting the project data to display the property displays the property as shown left.

In property display, the following information is displayed.

Item

Date

Author

Drawing S/W version

Description

Displays the creation date of the file.

Displays the author of the project data.

Displays name and version of the drawing software by which the project data is created.

2.

Touching by one line.

3.

Touching by one screen.

button scrolls up/down the screen

button scrolls up/down the screen

4.

Touching [ ] button closes the property display and returns to the previous screen.

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 21

(5) Data check operation

Carries out data check of the selected project file.

When data is normal.

1.

Touch [Data check] button after selecting a data check target file.

The dialog mentioned left will be displayed after executing data check.

2.

Touching [OK] button closes the dialog.

When data is erroneous.

(6) Download operation/setup operation

(a) Download operation

Transfers the project data stored in the A drive (Built-in SD Card) or E drive (USB drive) to the C drive

(Flash Memory). (The GOT monitors using the data in the C drive.)

(This item explains using the A drive.)

Before download operation

(1) Setup cancel

When the project data in the A drive is set up, the project data cannot be downloaded to the C drive.

Execute setup cancel (

(7) (b) Setup cancel operation) before downloading the project data.

(2) Project data to be stored in a SD card

When storing the project data from GT Designer3 to SD card, select [C: Built-in flash memory] for [Project

Data] in the [Boot Drive].

13 - 22

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

1.

Mount the SD card/USB memory to GOT.

2.

For the SD card installation/removal method, refer to the following.

8.1.2 Installing and removing procedures of the SD card

8.2.2 Installing and removing procedures of the USB memory

3.

Touch [A: Built-in SD card] of [Select drive].

9

10

4.

Touching [Download] button displays the screen shown on the left. Touching [OK] button executes the download.

11

12

5.

If there is a project data of the same name in the C drive, the screen shown on the left is displayed without starting the download.

Touching [OK] button executes an overwrite download to the project data of the same name.

Touching [Cancel] button cancels the download.

13

6.

When the download is completed, the dialogue box shown on the left is displayed.

Touching [OK] button restarts the GOT.

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 23

(b) Setup operation

Sets the project data stored in the A drive (Built-in SD card) to be used in the GOT.

The GOT monitors using the monitor data in the A drive.

Before setup operation

When storing project data from GT Designer3 to SD card, select [A: Standard SD Card] for [Project Data] in [Boot

Drive].

1.

Mount the SD card to GOT. For the SD card installation/removal method, refer to the following.

8.1.2 Installing and removing procedures of the SD card

2.

Touch [A: Built-in SD card] of [Select drive].

3.

Touching [Download] button displays the screen shown on the left.

Touching [OK] button executes the setup.

4.

When the setup is completed, the dialog box mentioned left is displayed.

Touching [OK] button restarts the GOT.

13 - 24

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

9

(7) Upload/setup cancel operation

(a) Upload operation

By upload operation, the project data is transferred from the C drive (Flash Memory) to the A drive (Build-in

SD card) or E drive (USB drive).

The SD card or USB memory after uploading can be used for downloading project data to another GOT.

(This item explains using the A drive.)

10

Before upload operation

The project data cannot be uploaded to the A drive when the project data of the A drive is set up.

Execute setup cancel (

(7)(b) Setup cancel operation) before uploading the project data.

11

1.

Touch [A: Built-in SD card] of [Select drive].

2.

Touching [Upload] button displays the screen shown on the left.

3.

Touching [OK] button executes the upload.

12

4.

If there is a project data of the same name in the A drive, the screen shown on the left is displayed without starting the upload.

Touching [OK] button executes an overwrite upload to the project data of the same name.

Touching [Cancel] button cancels the upload.

13

5.

When the uploading is completed, the dialog box mentioned left is displayed.

Touching [OK] button restarts the GOT.

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 25

(b) Setup cancel operation

By setup cancel, setup is canceled.

1.

Touch [A: Built-in SD card] of [Select drive].

2.

Touching [Upload] button displays the screen shown on the left.

3.

Touching [OK] button executes the setup cancel.

4.

When the setup cancel is completed, the dialog box mentioned left is displayed.

Touching [OK] button restarts the GOT.

After restart, the GOT monitors with the project data in the C drive.

13 - 26

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.4 Hard copy information

„

Function of hardcopy information

Carries out delete, copy and move to the file created by the hardcopy function.

For details of hard copy function, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Functions)

Function

Displaying file, folder data

Delete

Copy

Rename

Description

The file/folder type, name, data size and creating date & time are displayed.

File is deleted.

File is copied.

Renames file.

„

Display operation of Hardcopy information

(

Main menu

9.3 Utility Display)

Program/data control

Touch

[Program/data control]

Hard copy information

Touch

[Hard copy information]

9

Reference

13-28, 13-29

13-30

13-31

13-32

10

11

12

13

Select a drive and operate hard copy data files

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 27

„

Display example of Hardcopy information

Hard copy information

Hard copy information

Storage file/folder display screen

(2)

(7)

(3)

(4)

(8)

(5) (6)

(9)

(1)

Number Item

(1) Select drive

(2) Kind

(3) Name

(7)

(8)

(9)

(4)

(5)

(6)

Path name

Size

Date and time

The size of drive

Operation switch

Number of files

Description

The target drive which displays file or folder can be selected.

When SD card or USB memory is not installed, the following drives are not displayed.

• SD card: [A: Built-in SD card]

• USB memory: [E: USB drive]

Indicates the type of the displayed name (file or folder).

In case of file, displays the extension; in case of folder, displays "DIR".

(

Displays the file name or folder name.

For the long file/folder name, entire part may not be displayed.

Confirm the nondisplayed part with the [Copy] button, etc.

13.2.4

■

Hardcopy information operation (3) Copy operation)

After confirmation, touch the [Cancel] button to cancel the operation.

Displays the path name of drive/folder which is currently displayed.

Displays the size of the file displayed in [Name].

The date and time when each file was created are displayed.

Displays the size in use and the entire size of the drive which is selected by drive selection.

(Only the size in use is displayed when selecting the C drive.)

Execution switch of each function.

Displays the total number of the displayed files.

(1) Display of creation date and time

The creation date and time display is not updated even if a file is created or updated while displaying the hardcopy information. To display the updated creation date and time, close the screen currently displayed (by moving to the upper hierarchy folder, etc.) and display the screen again.

(2) Folders and files displayed

For the folders and files displayed, refer to the following.

13.1.4 Display file

13 - 28

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

Hardcopy information operation

(1) Display operation of Hardcopy information

9

1.

Touching a drive of [Select drive] displays the information of the touched drive.

2.

Touching a folder name displays the information of the touched folder.

3.

Touching a folder of [ . . ] displays the information of the folder of the one upper hierarchy.

4.

Touching button of the scrollbar scrolls up/ down the screen by one line.

Touching one screen.

button scrolls up/down the screen by

5.

Touching a file name selects the file.

6.

For the operations of the delete, copy, and rename, refer to the following.

Delete......................................

Copy........................................

Rename...................................

This section (2)

This section (3)

This section (4)

7.

Touching [ ] button closes the screen.

10

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 29

(2) Deletion operation

Deletes selected files.

1.

Touch and select the file to delete.

2.

Touching [Del] button displays the screen mentioned left.

Touching [OK] button deletes the file.

Touching [Cancel] button cancels the deletion.

3.

When the deletion is completed, the completion dialog is displayed.

4.

Touching [OK] button closes the dialog.

13 - 30

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(3) Copy operation

Copies the selected file.

9

1.

Touch and select the file to copy.

2.

Touching [Copy] button displays the message

[Please select a destination.] in the left bottom of the screen.

3.

If the copy destination folder is touched, the screen display is changed to the folder of copy destination.

At this time, it cannot be copied into the same folder where the file exists.

Select other folders.

10

11

4.

Touching [Exec.] button displays the dialog box shown left.

12

5.

Touch [OK] button.

If there is a file of the same name in the copy destination folder, the following dialog is displayed without starting the copy.

6.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the copy.

13

14

7.

When the copy is completed, the dialog of completion is displayed.

Touching [OK] button closes the dialog.

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 31

(4) Rename operation

Renames the selected file.

1.

Touch and select the file to change the name.

2.

Touching [Rename] button displays the screen shown left. Input the file name to be changed.

By touching the following button, input text type is changed.

[A-Z]: English capital

[0-9]: Numeric/Symbol

3.

Touching [Enter] button displays the dialog box shown left.

4.

Touching [OK] button starts renaming file.

5.

When renaming is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 32

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.5 Advanced recipe information

9

Before using advanced recipe information

For writing/reading into/from a controller with this function or editing of advanced recipe file on the personal computer, refer to the following manual.

Specifications and operating procedure are described.

GT Designer3 Version1 Screen Design Manual (Functions)

10

„

Function of advanced recipe information

For the advanced recipe file used in advanced recipe function, copy/delete/file output are available.

In addition, it is possible to writing/reading into/from a controller by using this function, without creating the screen to operate the advanced recipe. (Advanced recipe setting of GT Designer3 is required.)

Function Description

Displaying file, folder data The file/folder name, data size and creating date & time are displayed.

G1P file of advanced recipe file is converted to CSV file.

Reference

13-35, 13-37

13-38

G1P TXT conversion

G1P file of advanced recipe file is converted to Unicode text file.

13-38

Advanced recipe information screen

Advanced recipe record list screen conversion

Del

Copy

Move

Rename

Create Folder

Create G1P

Load record GOT

PLC

Save record PLC

GOT

Match records GOT

PLC

Delete Device Value

CSV file or Unicode text file is converted to G1P file of advanced recipe file.

File or folder is deleted.

File is copied.

File is moved.

File name is changed.

New folder is created.

New G1P file of advanced recipe file is created.

Selected record value is loaded in the device of controller.

The device of controller is saved in selected record.

Selected record is verified to the device value of controller.

The device value contained in selected record is deleted.

13-48

13-49

13-50

13-39

13-40

13-41

13-42

13-43

13-44

13-45

13-47

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 33

„

Display operation of Advanced Recipe information

(

Main menu

9.3 Utility Display)

Program/data control

Touch

[Program/data control]

Touch

[Advanced Recipe information]

Advanced Recipe information

13 - 34

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

9

„

Display example of Advanced Recipe information

(1) Advanced recipe information screen

Advanced Recipe Information screen

Advanced Recipe Information

Storage file/folder display screen

10

(2)

(6)

(3)

(4)

(7)

(5)

(8)

(1)

11

Number

(1) Select drive

Item

(2) Kind

(3) Name

(4)

(5)

(6)

(7)

(8)

Path name

Size

The size of drive

Operation switch

Number of files

Description

The target drive can be selected. (Even if SD card is not installed, this message appears.)

Indicates the type of the displayed name (file or folder).

In case of file, displays the extension; in case of folder, displays "DIR".

(

Displays the file name or folder name.

For the long file/folder name, entire part may not be displayed.

Confirm the nondisplayed part with the [Rename] button, etc.

13.2.5

■

Advanced recipe information operation(7) Rename operation)

After confirmation, touch the [Cancel] button to cancel the operation.

Displays the path name of drive/folder which is currently displayed.

Displays the size of the file displayed in [Name].

Displays the size in use and the entire size of the drive which is selected by drive selection.

Execution switch of each function.

Displays the total number of the displayed files.

12

13

(1) About the displayed file

The files other than that for advanced recipe are not displayed on the advanced recipe information screen.

(2) Folders and files displayed

For the folders and files displayed, refer to the following.

13.1.4 Display file

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 35

(2) Advanced recipe record list screen

Touching the [Execute] button on the advanced recipe information screen after selecting the advanced recipe file, this screen appears.

Records selected in each advanced recipe file can be displayed or saved/loaded.

Number

(1)

(2)

(3)

(4)

(5)

No.

Item Description

Record No. of advanced recipe file is displayed.

Attr

Attribution of record is displayed.

Attribution of record can be changed with GT Designer3.

V: Record can be loaded/saved(Record whose value is selected.)

VP: Record only for loading(Record whose value is selected and cannot be changed.)

Blank: Record only for saving(Record whose value is deleted or not selected.)

P: Record unusable (reserved area)(Record whose value is not selected and cannot be changed.)

Record Comment Record Comment is displayed.

File Name Path and name of recipe file are displayed.

Setting No.

Name

Operation switch

Recipe No. is displayed.

Recipe name is displayed.

Execution switch of each function.

13 - 36

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

Advanced recipe information operation

(1) Display operation of Advanced Recipe information

1.

Touching a drive of [Select drive] displays the information of the touched drive.

2.

Touching a folder name displays the information of the touched folder.

3.

Touching a folder name of [ . . ] displays the information of the folder in one upper hierarchy.

4.

Touching button of the scrollbar scrolls up/ down the screen by one line.

Touching button scrolls up/down the screen by one screen.

5.

Touching a file name selects the file.

6.

For operation of operating switches, refer to the following.

G1P CSV, G1P TXT...

CSV/TXT G1P...............

Delete...................................

Copy.....................................

This section (2)

This section (3)

This section (4)

This section (5)

Move.....................................

Rename................................

Create Folder........................

Create G1P...........................

Execute...................

This section (6)

This section (7)

This section (8)

This section (9)

This section (10) to (13)

7.

Touching [ ] button closes the screen.

9

10

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 37

(2) G1P CSV conversion operation, G1P TXT conversion operation

Advanced recipe file (G1P file) is converted to CSV file or Unicode text file that can be displayed/edited on personal computer.

1.

Touch and select the G1P file to convert into a

CSV file or a Unicode text file.

2.

Touch the following button in accordance with destination file type.

• CSV file: [G1P CSV] button

• Unicode text file: [G1P TXT] button

3.

Select the target folder.

(Selecting a folder is not needed for outputting directly below the drive.)

4.

Touching [Exec.] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

(Example: Dialog box if the [G1P CSV] button is touched.)

5.

When the file, whose name is the same, exists in the destination folder, the dialog box shown at left appears without starting the conversion.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the conversion.

6.

The message of completion is displayed in dialog box when conversion is completed.

Touching [OK] button closes the dialog.

13 - 38

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(3) CSV/TXT G1P conversion operation

CSV file or Unicode text file is converted to an advanced recipe file (G1P file).

1.

To select the file, touch the check box of CSV file or Unicode text file to be converted to a G1P file.

9

10

2.

Select the target folder.

(Selecting a folder is not needed for outputting directly below the drive.)

11

12

3.

Touching [Exec.] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

13

4.

When the file, whose name is the same, exists in the destination folder, the dialog box shown at left appears without starting the conversion.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the conversion.

14

15

5.

The message of completion is displayed in dialog box when conversion is completed.

Touching [OK] button closes the dialog.

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 39

(4) Deletion operation

Folder and file to be used on advanced recipe are deleted.

1.

Touch and select the file/folder to delete.

2.

Touching [Del] button displays the dialog mentioned left.

Touching [OK] button deletes the file/folder.

(While executing, "Processing..."message appears on the screen.)

Touching [Cancel] button cancels the deletion.

When it cannot be deleted, the dialog box shown at left appears. (Only when deleting folder is executed.)

Verify that there is no file in the folder and execute

( the delete operation again.

13.2.6

■

Precautions)

3.

When the deletion is completed, the completion dialog is displayed.

Touching [OK] button closes the dialog.

13 - 40

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(5) Copy operation

Folder to be used in advanced recipe is copied.

1.

Touch and select the file to copy.

2.

Touch the [Copy] button.

3.

Select the target folder.

(Selecting a folder is not needed for outputting directly below the drive.)

At this time, it cannot be copied into the same folder where the file exists.

Select other folders.

11

12

4.

Touching [Execute] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

13

5.

If there is a file of the same name in the copy destination folder, the following dialog is displayed without starting the copy.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the copy.

14

15

6.

When the copy is completed, the dialog of completion is displayed.

Touching [OK] button closes the dialog.

16

9

10

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 41

(6) Move operation

Files to be used in advanced recipe are moved.

1.

Touch and select the file to move.

2.

Touch the [Move] button.

3.

Select the target folder.

(Selecting a folder is not needed for moving directly below the drive.)

4.

Touching [Execute] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

5.

When any file with the same name exists in the destination folder, the dialog box shown left appears without starting the movement.

Touching the [OK] button overwrites the file.

Touching [Cancel] button cancels moving.

6.

When moving is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 42

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(7) Rename operation

File name to be used in advanced recipe is changed.

1.

Touch and select the file to change the name.

9

10

2.

Touching [Rename] button displays the screen shown left. Input the file name to be changed.

By touching the following button, input text type is changed.

[A-Z]: English capital

[0-9]: Numeric/Symbol

11

12

3.

Touching [Enter] button displays the dialog box shown left.

4.

Touching [OK] button starts renaming file.

(While executing, "Processing..."message appears on the screen.)

13

5.

When renaming is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 43

(8) Folder create operation

Folder to be used in advanced recipe is created.

1.

Touch the [Create Folder] button.

2.

The input key window shown left appears, then input the file name to be created.

By touching the following button, input text type is changed.

[A-Z]: English capital

[0-9]: Numeric/Symbol

3.

Touching [Enter] button displays the dialog box shown left.

4.

Touching [OK] button starts creating folder.

5.

When creating folder is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 44

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(9) G1P file create operation

Advanced recipe file (G1P file) is created.

When advanced recipe is only executed on Utility, advanced recipe file should be created with this function in advance.

1.

Touch the [Create G1P] button.

9

10

11

2.

The screen to select the advanced recipe setting is displayed.

Select the advanced recipe setting to be used for new file.

After selecting, touch the [Next] button.

12

3.

As the input key window is displayed, input the file name for new file.

By touching the following button, input text type is changed.

[A-Z]: English capital

[0-9]: Numeric/Symbol

13

14

4.

Touching [Enter] button displays the dialog box shown left.

Touch [OK] button.

15

(Continued to next page)

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 45

16

5.

When the file, whose name is the same, exists in the destination folder, the dialog box shown left appears without starting the creation.

Touching the [OK] button overwrites the file.

Touching [Cancel] button cancels creating.

6.

When creating is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 46

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(10) Record load operation

Selected record value is loaded in the device of controller.

1.

Select the recipe file and touch the [Execute] button.

9

10

2.

As the Advanced Recipe Record List screen is displayed, select the record comment to which you want to load the device value.

11

12

3.

Touching the [Load record GOT PLC] button displays the dialog box shown left.

4.

Touching the [OK] button starts loading record.

13

5.

When loading is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 47

(11) Record save operation

Device value of a controller is saved in the selected record.

1.

Select the recipe file and touch the [Execute] button.

2.

As the Advanced Recipe Record List screen is displayed, select the record comment for saving the device value.

3.

Touching the [Save record PLC GOT] button displays the screen shown left.

For changing the record comment of saving destination, input the record comment.

By touching the following button, input text type is changed.

[A-Z]: English capital

[a-z]: English minuscule

[0-9]: Numeric/Symbol

Other than alphanumeric and symbol can not be inputted.

If record comment is not changed, it is not need to input.

4.

Touching [Enter] button displays the dialog box shown left.

5.

Touching the [OK] button starts saving record.

6.

When saving is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 48

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(12) Record match operation

Verifies weather selected record matches to the device value of the controller.

After executing loading/saving with advanced recipe, verifies weather its contents are reflected.

1.

Select the recipe file and touch the [Execute] button.

9

10

2.

As the Advanced Recipe Record List screen is displayed, select the record comment for matching the device value.

11

12

3.

Touching the [Match records GOT PLC] button displays the dialog box shown left.

4.

Touching the[OK] button starts matching record.

13

5.

When matching is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

14

15

6.

If selected record does not match to the device value of controller, the dialog box shown left is displayed.

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 49

(13) Device value delete operation

The device value of selected record is deleted (without value) and changed to record only for reading.

(The record name is not deleted.)

1.

Select the recipe file and touch the [Execute] button.

2.

As the Advanced Recipe Record List screen is displayed, select the record comment to be deleted.

(If the data of which attribution contains "P" can not be deleted.)

3.

Touching the [Delete Device Value] button displays the dialog box shown left.

4.

Touching the [OK] button starts deleting device value.

(The "Processing..." message is displayed on the screen.)

5.

When deleting is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 50

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

Precautions

(1) When creating folder/file

(a) Number of characters set for folder or file name when creating folder/file.

GOT recognizes file location according to path explained below.

Specify folder or file name, and total characters of path cannot exceed 78 characters.

Users only can rename folder or file name.

(Other than folder/file name is automatically printed.)

Example: CSV file Path in SD card or USB memory

A :\

Folder name

\ File name .CSV

(2 characters)

Drive name

(1 character)

(1 character)

Extension

(4 characters)

Max. 78 characters

9

10

11

12

If folder is assigned the hierarchy.

The \ mark is displayed between folder name and folder name, folder name and file name. The \ mark is also counted as one character.

(b) Character strings that cannot be set to folder/file

The following character strings cannot be used as a folder name or a file name. Even small characters of those cannot be used.

• COM1 to COM9 • LPT1 to LPT9 • AUX • CON

• NUL • PRN • CLOCK$

In addition, the folder/file name shown below cannot be used.

• The folder name which begins with G1.

• Folder name and file name which begin with . (period).

• Folder name and file name which finish with . (period).

• Folder name and file name which have only . (one period) or ..(two periods).

(c) For deleting the folder

The folder in which the file exists cannot be deleted.

Delete the folder after having deleted the files.

In addition, on the advanced recipe information screen, the file other than that for advanced recipe is not displayed on GOT.

When the folder, in which there is no file displayed on the screen, cannot be deleted, confirm whether there is other file in SD card or USB memory by using personal computer, etc.

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 51

(2) Precautions for operation

(a) Precautions during folder/file operation (Create/Delete/Copy/File output, etc)

Even if SD card access switch has been turned OFF while GOT is processing folders and files, the processing continues to be executed. (Example: Even if SD card access switch has been turned OFF while

GOT is creating a folder, the folder is created.)

Therefore, do not pull out the SD card while the "Processing..." message is on the screen after SD card access switch has been turned OFF.

(b) While GOT is accessing to other file (Alarm data, etc)

When folder/file processing for the recipe is executed while the GOT is in access to other file (SD card access LED ON), the GOT executes folder/file processing for the Advanced Recipe after the processing for other file has completed.

Therefore, it may take some time to finish the process of advanced recipe folder/file. (The "Processing..." message is displayed on the screen.)

Estimation of processing time

The process may take time depending on the setting of advanced recipe file to be operated. (The more number of blocks increases, the longer it takes to process advanced recipe folder/file.)

Also, the process to create the first file may take time depending on the setting of advanced recipe file.

(Reference value)

Direct connection to QCPU and CPU(device point:32767 points setting, transmission speed: 115200bps)

• When the block setting number to 1: about 17 seconds

• When the block setting number to 2048: about 4 minutes

(c) For executing the saving/loading of device value with advanced recipe file which has been moved or whose name has been changed.

Adjust [Recipe File] setting of advanced recipe setting with GT Designer3 to file which has been moved or whose name has been changed.

After the setting has been changed, download the advanced recipe setting to GOT.

13 - 52

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.6 Logging information

„

Function of logging information

Logging files created with the logging function can be copied, deleted or renamed, etc.

Without using a PC, you can manage logging files on the GOT.

For details of the logging function, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Functions)

Function

Displaying file, folder data

Description

The file/folder name, data size and creating date & time are displayed.

G1L CSV conversion

G1L TXT conversion

Del

Copy

Move

Rename

Create Folder

G1L file of loggingfile is converted to CSV file.

G1L file of loggingfile is converted to Unicode text file.

File or folder is deleted.

File is copied.

File is moved.

File name is changed.

New folder is created.

„

Display operation of Logging information

Main menu

(

9.3 Utility Display)

Program/data control

Touch

[Program/data control]

Logging information

Touch

[Logging information]

9

10

Reference

13-54, 13-55

13-56

13-56

13-57

13-58

13-59

13-60

13-61

11

12

13

14

Select a drive and operate logging data files

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 53

„

Display example of Logging information

Logging Information

Logging Information

Storage file/folder display screen

(2)

(6)

(3)

(4)

(7)

(5)

(8)

(1)

Number

(1) Select drive

Item

(2) Kind

(3) Name

(4)

(5)

(6)

(7)

(8)

Path name

Size

The size of drive

Operation switch

Number of files

Description

The target drive can be selected. (Even if SD card is not installed, this message appears.)

Indicates the type of the displayed name (file or folder).

In case of file, displays the extension; in case of folder, displays "DIR".

(

Displays the file name or folder name.

For the long file/folder name, entire part may not be displayed.

Confirm the nondisplayed part with the [Rename] button, etc.

13.2.6

■

Logging information operation (6)Rename operation)

After confirmation, touch the [Cancel] button to cancel the operation.

Displays the path name of drive/folder which is currently displayed.

Displays the size of the file displayed in [Name].

Displays the size in use and the entire size of the drive which is selected by drive selection.

Execution switch of each function.

Displays the total number of the displayed files.

(1) About the displayed file

The files other than that for logging are not displayed on the logging information screen.

(2) Folders and files displayed

For the folders and files displayed, refer to the following.

13.1.4 Display file

13 - 54

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

Logging information operation

(1) Display operation of logging information

9

1.

Touching a drive of [Select Drive] displays the information of the touched drive.

2.

Touching a folder name displays the information of the touched folder.

3.

Touching a folder name of [ . . ] displays the information of the folder in one upper hierarchy.

4.

Touching button of the scrollbar scrolls up/ down the screen by one line.

Touching button scrolls up/down the screen by one screen.

5.

Touching a file name selects the file.

6.

For operation of operating switches, refer to the following.

G1L CSV, G1L TXT...

Delete...................................

Copy.....................................

Move.....................................

Rename................................

Create Folder........................

This section (2)

This section (3)

This section (4)

This section (5)

This section (6)

This section (7)

7.

Touching [ ] button closes the screen.

10

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 55

(2) Operation of G1L CSV conversion G1L TXT conversion

Logging file (G1L file) is converted to CSV file or Unicode text file that can be displayed/edited on PC.

1.

Touch and select the G1L file to convert into a

CSV file or a Unicode text file.

2.

Touch the following button in accordance with destination file type.

• CSV file: G1L CSV button

• Unicode text file: G1L TXT button

3.

Select the target folder.

(Selecting a folder is not needed for outputting directly below the drive.)

4.

Touching [Execute] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

(Example: Dialog box if the [G1L CSV] button is touched.)

5.

When the file, whose name is the same, exists in the destination folder, the dialog box shown at left appears without starting the conversion.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the conversion.

6.

The message of completion is displayed in dialog box when conversion is completed.

Touching [OK] button closes the dialog.

13 - 56

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(3) Deletion operation

Folder and file to be used on logging are deleted.

1.

Touch and select the file/folder to delete.

9

10

2.

Touching [Del] button displays the dialog mentioned left.

Touching [OK] button deletes the file/folder.

(While executing, "Processing..."message appears on the screen.)

Touching [Cancel] button cancels the deletion.

11

12

3.

When the deletion is completed, the completion dialog is displayed.

Touching [OK] button closes the dialog.

13

14

4.

When it cannot be deleted, the dialog box shown at left appears. (Only when deleting folder is executed.)

Verify that there is no file in the folder and execute

( the delete operation again.

13.2.6

■

Precautions)

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 57

(4) Copy operation

Folder to be used in logging is copied.

1.

Touch and select the file to copy.

2.

Touch the [Copy] button.

3.

Select the target folder.

(Selecting a folder is not needed for outputting directly below the drive.)

At this time, it cannot be copied into the same folder where the file exists.

Select other folders.

4.

Touching [Execute] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

5.

If there is a file of the same name in the copy destination folder, the following dialog is displayed without starting the copy.

Touching [OK] button overwrites the file.

Touching [Cancel] button cancels the copy.

6.

When the copy is completed, the dialog of completion is displayed.

Touching [OK] button closes the dialog.

13 - 58

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(5) Move operation

An operation log file is moved.

1.

Touch and select the file to move.

2.

Touch the [Move] button.

3.

Select the target folder.

(Selecting a folder is not needed for moving directly below the drive.)

11

12

4.

Touching [Execute] button displays the dialog box shown left.

Touch [OK] button.

(While executing, "Processing..."message appears on the screen.)

13

5.

When any file with the same name exists in the destination folder, the dialog box shown left appears without starting the movement.

Touching the [OK] button overwrites the file.

Touching [Cancel] button cancels moving.

14

15

6.

When moving is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

16

9

10

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 59

(6) Rename operation

An operation log file is changed.

1.

Touch and select the file to change the name.

2.

Touching [Rename] button displays the screen shown left. Input the file name to be changed.

By touching the following button, input text type is changed.

[A-Z]: English capital

[0-9]: Numeric/Symbol

3.

Touching [Enter] button displays the dialog box shown left.

4.

Touching [OK] button starts renaming file.

(While executing, "Processing..."message appears on the screen.)

5.

When renaming is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

13 - 60

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(7) Folder create operation

An operation log folder is created.

1.

Touch the [Create Folder] button.

2.

The input key window shown left appears, then input the file name to be created.

By touching the following button, input text type is changed.

[A-Z]: English capital

[0-9]: Numeric/Symbol

11

12

3.

Touching [Enter] button displays the dialog box shown left.

4.

Touching [OK] button starts creating folder.

13

14

5.

When creating folder is completed, completion dialog box is displayed.

Touching [OK] button closes the dialog.

15

9

10

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 61

„

Precautions

(1) When creating folder/file

(a) Number of characters set for folder or file name when creating folder/file.

GOT recognizes file location according to path explained below.

Specify folder or file name, and total characters of path cannot exceed 78 characters.

Users only can rename folder or file name.

(Other than folder/file name is automatically printed.)

Example: CSV file Path in SD card or USB memory

A :\

Folder name

\

File name

.CSV

(2 characters)

Drive name

(1 character)

(1 character)

Extension

(4 characters)

Max. 78 characters

13 - 62

If folder is assigned the hierarchy.

The \ mark is displayed between folder name and folder name, folder name and file name. The \ mark is also counted as one character.

(b) Character strings that cannot be set to folder/file

The following character strings cannot be used as a folder name or a file name. Even small characters of those cannot be used.

• COM1 to COM9 • LPT1 to LPT9 • AUX • CON

• NUL • PRN • CLOCK$

In addition, the folder/file name shown below cannot be used.

• The folder name which begins with G1.

• Folder name and file name which begin with . (period).

• Folder name and file name which finish with . (period).

• Folder name and file name which have only . (one period) or ..(two periods).

(c) For deleting the folder

The folder in which the file exists cannot be deleted.

Delete the folder after having deleted the files.

In addition, on the logging information screen, the files other than logging files are not displayed on GOT.

When the folder, in which there is no file displayed on the screen, cannot be deleted, confirm whether there is other file in SD card or USB memory by using personal computer, etc.

(2) Precautions for operation

(a) Precautions during folder/file operation (Create/Delete/Copy/File output, etc)

Even if SD card access switch has been turned OFF while GOT is processing folders and files, the processing continues to be executed.

(Example: Even if SD card access switch has been turned OFF while GOT is creating a folder, the folder is created.)

Therefore, do not pull out the SD card while the "Processing..." message is on the screen after SD card access switch has been turned OFF.

(b) While GOT is accessing to other file (Alarm data, etc)

When folder/file processing for the logging is executed while the GOT is in access to other files (SD card access LED ON), the GOT executes folder/file processing for the logging after the processing for other files is completed.

Therefore, it may take some time to finish the process of the logging folder/file.

(The "Processing..." message is displayed on the screen.)

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.7 Memory card format

„

Function of the memory card format

Format the SD card/USB memory/Internal SRAM.

„

Display operation of Memory card Format

(

Main menu

9.3 Utility Display)

Program/Data control

Touch

[Program/data control]

Memory card Format

Touch

[Memory card Format]

Move to Memory card format

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 63

13

14

15

11

12

9

10

16

„

Memory card format operation

1.

Mount the SD card/USB memory to GOT.

For inserting/removing method of SD card/USB memory, refer to the following.

8.1.2 Installing and removing procedures of the SD card

8.2.2 Installing and removing procedures of the USB memory

2.

Touch and select the drive to format by drive selection.

3.

Touching [Format] button displays the password input screen.

4.

Typing

1 1 1 1

and touching the [Enter] key display the dialog box shown on the left. (The password is fixed to 1111.)

Confirm the contents of the dialog box, and touch

[OK] button when execute the format of SD card or

USB memory.

To cancel the memory card format, touch [Cancel] button.

5.

When touching the [OK] button in , the dialog box shown left appears for recheck.

6.

Reconfirm whether to format the SD card or USB memory.

Touching the [OK] button starts the format.

Touching the [Cancel] button cancels the format of

SD card or USB memory.

7.

When the formatting is completed, the completion dialog mentioned left is displayed.

8.

Touching the [OK] button closes the dialog box.

13 - 64

Restrictions on formatting

• When use an unformatted SD card or USB memory in GOT, format the SD card or USB memory by PC. GOT cannot format the unformatted SD card or USB memory.

• The formatting of GOT does not change the file system (Example: FAT16) of the SD card or USB memory and inherits the file system before formatting.

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.8 Memory information

„

Memory information functions

Displays the flash memory empty area size available for the user of each drive and Boot drive empty area size.

Confirming memory empty space is enabled without connecting a PC.

„

Display operation of Memory information

(

Main menu

9.3 Utility Display)

Program/Data control

9

10

Touch

[Program/data control]

Touch

[Memory informaton]

11

Memory information

12

13

„

Display example of Memory information

14

(1)

(2)

Number

(1)

Item

Flash memory empty area size

(2) Boot drive empty area size

Description

Indicates the memory space of each drive available for the user to store files or folders.

The [A: Built-in SD card] is not displayed when SD card is not installed.

If the USB memory is not installed, [E: USB drive] is not displayed.

Indicates the empty area size of boot drive specified by the user.

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 65

15

16

13.2.9 USB device status display

„

Function of USB device status display

This function displays a list of the USB device connection status in the GOT.

Also, this screen is used to remove the USB device from GOT.

„

Display operation of USB device status display

(

Main menu

9.3 Utility Display)

Program/Data control

Touch

[Program/data control]

Touch

[USB device status display]

USB device status display

13 - 66

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

„

USB device status display operation

9

1.

When the USB device is installed to GOT, the screen shown left is displayed.

2.

USB mass storage is displayed in Device, and [Stop] button is displayed in Attach.

10

3.

Touching the [Stop] button displays the dialog box shown left.

Touching the [OK] button execute the preparation of the USB devices removal.

Touching the [Cancel] button cancels the preparation of USB devices removal.

11

4.

When the preparation of removal is ready, the dialog box shown left is displayed.

5.

Touching the [OK] button closes the dialog box.

12

13

USB mouse/keyboard recognition

When using the USB mouse/keyboard, install [USB mouse/keyboard] of the extended function OS to the GOT.

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 67

13.2.10 SRAM control

„

Function of SRAM control

The SRAM user area usage can be confirmed, data in the SRAM user area can be backed up or restored, and the

SRAM user area is initialized.

For the available functions in the SRAM user area, refer to the following.

GT Designer3 Version1 Screen Design Manual (Functions)

„

Display operation of SRAM control

Main menu

(

9.3 Utility Display)

Program/Data control

Touch

[Program/data control]

Touch

[SRAM control]

SRAM control

13 - 68

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

9

„

Display example of SRAM control

(1)

(2)

(8)

(5)

(2) (3)

(4) (6) (7)

10

(10)

(12)

(9)

11

(11) (13) (14)

Number

(1)

(2)

(6)

(7)

(8)

(9)

(3)

(4)

(5)

(10)

(11)

(12)

(13)

(14)

Item

Check box

Function name

Setting ID

Size

Setting name

Date and time

Number of selected files

SRAM area

Drive space

Initialize all

Initialize selected area

Select drive

Restoration

Backup all area

Touch the check box to select or clear the item.

Description

Displays the used functions in the order of the advanced system alarm, advanced user alarm, and logging function.

Displays the setting IDs. The setting IDs of the advanced system alarm are not displayed.

Displays the data size.

Displays the setting name. For the setting name, only characters within the display range are displayed.

Displays the creation date and time of each data.

Displays the information of the items currently selected.

Displays the current free space size or total size of the SRAM user area.

Displays the current free space size or total size of the drive selected for [Select drive].

Initializes all areas of the SRAM user area.

Select each area of the SRAM user area to initialize multiple areas of the SRAM user area.

Switches drives to be used for the data backup or restoration in the SRAM user area.

Saves the data in the selected drive to SRAM user area.

The following drives can be switched only when a SD card or USB memory is installed.

• SD card: [A: Built-in SD card]

• USB memory: [E: USB drive]

Saves data in the SRAM user area to the selected drive.

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 69

„

SRAM control operation

(1) Operation to initialize all or selected areas of the SRAM user area

1.

Perform any of the following operations.

• To initialize all areas of the SRAM user area, touch the [Initialize all] button.

• To initialize selected areas of the SRAM user area, select the check box of the area to be initialized, and then touch the [Initialize selected area] button.

(Example: Dialog box when touching the [Initialize all] button)

2.

The dialog box shown left appears.

Check the description of the dialog box. To initialize the SRAM user area, touch the [OK] button.

To cancel the initialization, touch the [Cancel] button.

3.

When touching the [OK] button in , the dialog box shown left appears for recheck.

Touching the [OK] button starts the initialization.

Touching the [Cancel] button cancels the initialization.

4.

The completion dialog box appears when the initialization is completed.

Touching the [OK] button closes the dialog box.

13 - 70

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

(2) Operation to restore data

1.

To restore data in the drive to the SRAM user area

Select the drive where the data is stored, and then touch the [Restoration] button.

9

10

2.

The dialog box shown left appears.

Check the description of the dialog box. To restore all data in the SRAM user area, touch the [OK] button.

To cancel the restoration, touch the [Cancel] button.

11

12

3.

When touching the [OK] button in , the dialog box shown left appears for recheck.

Touching the [OK] button starts the restoration.

Touching the [Cancel] button cancels the restoration.

13

4.

The completion dialog box appears when the restoration is completed.

Touching the [OK] button closes the dialog box.

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 71

(3) Operation to back up all data in the SRAM user area

1.

To back up data in the SRAM user area to a drive

Select the drive where the data is to be stored, and then touch the [Backup all area] button.

2.

The dialog box shown left appears.

Check the description of the dialog box. To back up all data in the SRAM user area, touch the [OK] button.

To cancel the backup, touch the [Cancel] button.

3.

When touching the [OK] button in , the dialog box shown left appears for recheck.

Touching the [OK] button start the backup.

Touching the [Cancel] button cancels the backup.

4.

When the file, whose name is the same, exists in the destination folder, the dialog box shown left appears without starting the backup.

Touching [OK] button overwrites the file.

Touching the [Cancel] button cancels the backup.

5.

The completion dialog box appears when the restoration is completed.

Touching the [OK] button closes the dialog box.

13 - 72

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13.2.11 GOT data package acquisition

„

GOT data package acquisition function

The GOT data package acquisition copies the installed OS or data in the GOT main unit to the SD card or USB memory.

• OS (Boot OS, standard monitor OS, communication driver, extended function OS, option OS)

• Special data

• Project data

The copied data can be utilized for backup or creating the same GOT system by installing the data.

For installation function of the GOT, refer to the following.

16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory

„

Display operation of GOT data package acquisition

(

Main menu

9.3 Utility Display)

Program/Data control

9

10

11

12

Touch

[Program/data control]

Touch

[GOT data package acquisition]

GOT data package acquisition

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 73

„

Display example of GOT data package acquisition

Number

(1)

(2)

Select drive

Copy

Item Description

Displays the drive where OS and data can be copied.

The [A: Built-in SD card] is not displayed when SD card is not installed.

If the USB memory is not installed, [E: USB drive] is not displayed.

Touching the button starts copying.

„

GOT data package acquisition operation

(1) Display operation of GOT data package acquisition

The GOT data package acquisition copies the installed OS or data in the GOT main unit to the SD card or USB memory.

(This item explains using the A drive.)

1.

Touching the drive name below [Select Drive] inverts the touched drive name.

Touching the [Copy] button starts copying.

2.

The display depends on the status of copy destination and setup.

Operate with following the displayed dialog box.

3.

After copying OS and data, the dialog box for notifying the completion appears.

Touching the [OK] button closes the dialog box.

13 - 74

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

9

Estimation of processing time

The time required for the processing depends on conditions such as OS, data capacity, and file structure.

(Reference value)

• When the capacity is 4 Mbytes: Around 6 seconds

• When the capacity is 12 Mbytes: Around 18 seconds

(2) Precautions for operation

(a) Copying project data

If the Boot source drive and copy destination drive for project data is the same, the project data cannot be copied.

If the drives are the same, cancel the setup.

(b) When project data are copied to the GOT

If OS or project data is copied to the GOT using the SD card or USB memory created with GOT data package acquisition, the utility setting is also copied.

Check each utility setting after copying to the GOT and change the setting according to need.

(c) SD card or USB memory to be used

When performing GOT data package acquisition, do not store other data to the SD card or USB memory.

If doing so, the previous data will be unavailable.

10

11

12

13

14

15

16

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

13 - 75

13 - 76

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

13.2 Various Data Control

14. GOT SELF CHECK (DEBUG AND

SELF CHECK)

The GOT can display the screen for debugging and self-checking.

The following describes the functions available as the debugging and self checking functions.

Item

Debug

Self check

System alarm display

GOT start time

Description

System monitor, A list editor, FX list editor, Backup/restoration

Memory check, Display check, Touch panel check, I/O check

GOT error, CPU error

GOT start time

Reference

14-1

14-3

14-17

14-19

10

11

14.1 Debug

In this manual, the overview of the debugging function is described.

For display contents and operation procedure of debugging, refer to the following manual.

GOT1000 Series Extended/Option Functions Manual for GT Works3

The following describes the functions available as the debugging function.

Item

System monitor

A list editor

FX list editor

Backup/restoration

Description

The device of PLC CPU and buffer memory of intelligent function module can be monitored or tested.

The sequence program of ACPU can be list edited.

The sequence program of FXCPU can be list edited.

Data can be backed up/restored from the controller to GOT, or backup data can be deleted.

12

Reference

14-1

14-1

14-1

14-2

13

9

14.1.1 System monitor

System monitor allows monitoring and changing the devices in controllers.

For display contents and operation procedure, refer to the following manual.

GOT1000 Series Extended/Option Functions Manual for GT Works3

14.1.2 A list editor

MELSEC-A list editor allows changing the sequence programs in ACPU/QCPU (A mode).

For display contents and operation procedure, refer to the following manual.

GOT1000 Series Extended/Option Functions Manual for GT Works3

14.1.3 FX list editor

FX list editor allows changing the sequence programs in an FX PLC.

For display contents and operation procedure, refer to the following manual.

GOT1000 Series Extended/Option Functions Manual for GT Works3

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.1 Debug

14 - 1

14

15

16

14.1.4 Backup/restoration

„

Display operation of Backup/restoration

(

Main Menu

9.3 Utility Display)

Debug & self check

Touch

[Debug]

Touch

[Debug & self check]

Backup/restoration function

Debug

Touch

[Backup/restoration]

„

Operation of Backup/restoration

Backup/restore data from the controller to GOT, or delete backup data with the backup/restoration.

GOT data package acquisition is also possible.

For details of backup/restoration, refer to the following manuals.

GOT1000 Series Extended/Option Functions Manual for GT Works3

14 - 2

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.1 Debug

14.2 Self Check

The following describes the functions available as the self check function.

Item Description

Carries out write/read check of the SD card, USB memory, built-in flash memory, or internal SRAM.

Memory check

[Password]

5 9 2 0

Drawing check

Font check

Touch panel check

I/O check

Carries out missing bit check, color check and drawing check.

Displays the character data on the screen to check visually.

Checks whether there are no dead zone area in the Touch key minimum unit (2 dots 2 dots).

Carries out RS-232, RS-422/485 connecting target confirmation and self-loopback check.

9

Reference

14-3

14-6

14-10

14-12

14-14

10

14.2.1 Memory check

„

Memory check function

Memory check function carries out the write/read check of A drive (Built-in SD Card), C drive (Flash Memory), D drive

(Internal SRAM) and E drive (USB memory).

Function

A drive memory check

C drive memory check

D drive memory check

E drive memory check

Description

Checks whether the memory (Built-in SD card) of the A drive can be read/written normally.

Checks whether the memory (Flash Memory) of the C drive can be read/written normally.

Checks whether the memory (Internal SRAM) of the D drive can be read/written normally.

Checks whether the memory (USB memory) of the E drive can be read/written normally.

„

Display operation of Memory check

11

12

13

(

Main Menu

9.3 Utility Display)

Debug & self check

Self check

Touch

[self check]

Touch

[Memory check]

Touch

[Debug & self check]

14

Memory check

15

Select the memory to check and touch [Check].

16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 3

„

Memory check operation

Carries out write/read check of memory.

When drive is not displayed

When the drive (memory) to check is not displayed, confirm the mounting procedure or memory type with reference to the following.

8.1 SD Card

8.2 USB Memory

When no faults are found in mounting, etc, a memory failure may be arisen.

Replace the SD card or USB memory or built-in flash memory (C drive).

For details of built-in flash memory, contact your local Mitsubishi (Electric System) Service.

The following example explains about Memory Check using built-in flash memory (C drive).

For the Built-in SD card (A drive) memory check, install the SD card before carrying out the same key operations as built-in flash memory. For the USB drive (E drive) memory check, install the USB memory before carrying out the check operations.

1.

Select a drive to check in the Select Drive screen in

Memory check and touch [Check] button.

2.

Touching [Check] button displays the dialog box on the left.

Selecting [OK] button displays the numeric keyboard window.

Selecting [Cancel] button returns to the initial menu.

3.

Touch to input password (

[Enter] key.

5 9 2 0

) and touch

Touching [Enter] key executes read/write check for the built-in flash memory, which is completed in around 10 seconds.

14 - 4

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

(1) Password change

The password cannot be changed.

When input password error, the cancel dialog box is displayed.

Touching [OK] returns to the Memory check screen.

(2) When error is found in memory

When error is found by memory check, the dialog box indicating the area in which the error occurred is displayed.

In case of error, contact your local Mitsubishi (Electric

System) Service.

Touching [OK] returns to the Memory check screen.

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 5

13

14

15

11

12

9

10

16

14.2.2 Drawing check

„

Drawing check function

The drawing check function carries out display checks as missing bit check, color check, basic figure display check, move check among screens.

„

Display operation of drawing check

(

Main Menu

9.3 Utility Display)

Debug & self check

Self check

Touch

[Self check]

Touch

[Display check]

Touch

[Debug & Self check]

Drawing check

Display check

Touch

[Drawing check]

Notes on drawing check

Missing bits is occurred in the following cases.

• There are parts drawn in different color with the filled color.

• There are parts of basic figure and drawing patterns which are not drawn according to the layout and procedures described in "

14.2.2

■

Display operation of drawing check".

When missing bits occurs, contact your local Mitsubishi (Electric System) Service.

14 - 6

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

„

Drawing check operation

The screen for drawing check can be displayed by touching [Drawing check] on the Display check menu.

(1) Before execute drawing check

Touching the upper right part of the screen proceeds to the next check in each step during drawing check.

Touching the upper left part of the screen returns to the

[Display check] screen.

For GT1455-Q (65536 colors), the screen is displayed in color (blue, black, red, purple, green, light blue, yellow and white).

Also, for GT1450-Q (monochrome 16 scales), the screen color is reduced to monochrome 16 scales and displayed.

This section explains in the case of GT1455-Q (65536 colors).

Upper-left touch position

Upper-right touch position

9

10

11

(a) Missing bit, Color Check

By touching the upper-right part of the screen, the entire screen color changes in the following order: blue

black red purple green light blue yellow white.

Check missing bit and color visually.

12

Blue Black Red Purple Green Light blue Yellow White

To (b) Basic figurecheck screen

Touching the upper right part of the screen at the final color (white screen) displays the following (b) Basic figure check screen.

(b) Basic figure check

Check whether there is no shape transformation of basic figure or display losses.

The basic figure drawn has 4 types: 1. Filled circle, 2. Line, 3. Rectangle, 4. Ellipse.

13

14

To Pattern 1 of (c) Move check among screen

15

16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 7

(c) Move check among screens

• Pattern 1: Shape transformation, color check

The drawn figures are displayed in order and at regular intervals.

If the shape and color are displayed visually in order, it is normal

To Pattern 2

Pattern 1

• Pattern 2: Shape transformation, color check

The drawn figures are displayed in order and at regular intervals.

If the shape and color are displayed visually in order, it is normal.

To Pattern 3

Pattern 2

14 - 8

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

• Pattern 3: Shape transformation, color check

The overlapped shapes of pattern 1 and pattern 2 are displayed.

If the shape and color are displayed visually in order, it is normal.

To Pattern 4

• Pattern 4: Shape check

The drawn figures are displayed in order and at regular intervals.

If the shape and interval are displayed visually in order, it is normal.

Touching the upper right part of the screen returns to the [Display check] screen.

To [Display check]

The main screen image after the screen information read and write is executed

13

14

15

11

12

9

10

16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 9

14.2.3 Font check

„

Font check function

The font check is a function which confirms fonts installed in GOT. The character data of the font is displayed on the upper left part of the screen one by one.

„

Display operation of Font check

Main Menu

(

9.3 Utility Display)

Debug & self check

Self check

Touch

[Self check]

Touch

[Display check]

Touch

[Debug & Self check]

Font check

Display check

Touch

[Font check]

Notes on Font Check

Judged as normal if the following characters are correctly displayed. (UNICODE)

• Alphabetic characters etc.

: 0x0000 to 0x04F9 (From basic Latin to Kirill)

• Hangul characters

• Kanji

: 0xAC00 to 0xD7A3 (Hangul / Hangul auxiliary)

: 0x4E00 to 0x9FA5 (CJK integrated Kanjis)

If the characters above are not displayed correctly, the fonts may not be installed. Install the standard monitor OS again.

14 - 10

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

9

„

Font check operation

Font check starts by touching [Font Check] in the [Display check] screen.

The character data of the built-in font (in the built-in flash memory) can be checked visually to confirm the font drawings by displaying the character data serially on the screen.

(1) Before execute font check

Touching the upper right part of the screen proceeds to the next check in each step during Font check.

Touching the upper left part of the screen returns to the

[Display check] screen.

Upper-left touch position

Upper-right touch position

10

11

The installed font data is displayed by touching the upper right part of the screen.

Font data

12

13

Option fonts

To display optional fonts, the option font installation is required.

The option fonts are displayed at the end.

14

15

16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 11

14.2.4 Touch panel check

„

Touch panel check function

Touch panel check function checks whether there are no dead zone area in 2 dots 2 dots.

„

Display operation of Touch panel check

(

Main menu

9.3 Utility Display)

Debug & self check

Self check

Touch

[Self check]

Touch

[Touch panel check]

Touch

[Debug & self check]

Touch panel check

Touch

[OK]

Notes on Touch panel check

If the touched part is not filled with yellow color, there are the following two possible causes.

1. Display part failure

2. Touch panel failure

In that case, contact your local Mitsubishi (Electric System) Service.

14 - 12

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

„

Touch panel check operations

Touching [Touch panel check] of self-check displays a black-filled screen over the entire screen area.

1.

Touch a part of the screen.

The touched part becomes a yellow-filled display.

9

10

Black-filled screen

Yellow color

11

2.

Touching the upper left part returns to the self-check.

12

Upper-left touch position

13

Checking the upper left part of the screen

Only the upper left part of the screen cannot be filled with yellow.

If returns to the self-check by touching the upper left part, judge that the upper left area operates normally.

14

15

16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 13

14.2.5 I/O check

„

I/O check function

The I/O check is a function which checks whether GOT and PLC can communicate with each other.

If I/O check ends normally, the communication interface and the connection cable hardware are normal.

To execute I/O check, the communication driver has to be installed in GOT in advance from GT Designer3.

Note that the GOT restarts when this function is performed.

For the details related to the installation of the communication driver, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

(1) Communication drivers inapplicable to I/O check

When the following communication drivers are used, the I/O check cannot be executed.

Connection type

Connection to MITSUBISHI PLC

Connection to YASKAWA PLC

Connection to YOKOGAWA PLC

Connection to ALLEN-BRADLEY PLC

Connection to SIEMENS PLC

Microcomputer connection

Inverter connection

Ethernet connection

MODBUS(R)/TCP connection

Connection to YAMATAKE temperature controller

Connection to RKC temperature controller

Communication driver

Ethernet(MELSEC), Q17nNC, CRnD-700

YASKAWA GL/CP9200(SH/H)/CP9300MS, Ethernet (YASKAWA)

YOKOGAWA FA500/FA-M3/STARDOM, Ethernet (YOKOGAWA)

EtherNet/IP(AB)

SIEMENS S7, SIEMENS S7-200, SIEMENS S7-300/400

Computer

FREQROL 500/700

MODBUS/TCP

YAMATAKE SDC/DMC

RKC SR Mini HG (MODBUS)

„

Display operation of I/O Check

(

Main menu

9.3 Utility Display)

Debug & self check

Self check

Touch

[Debug & self check]

Touch

[Self check]

Touch

[I/O check]

I/O check

14 - 14

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

9

„

I/O check operation

(1) Connecting target confirmation

Touching [CPU] button carries out the connecting target confirmation communication check.

1.

After the CPU communication starts normally, the dialog box mentioned left notifying that it is on checking, until the connecting target confirmation communication ends normally.

10

2.

When the connecting target confirmation communication ends, its result is notified by dialog box.

If the connecting target confirmation communication ends normally, the dialog box notifying of the normal termination mentioned left is displayed. Touching [OK] button after confirming the result returns to [I/O check].

11

If the dialog box mentioned left is displayed after selecting connecting target confirmation or during CPU communication check, confirm the following.

• No misconnection with CPU

( GOT1000 Series Connection Manual for GT

Works3)

• No missettings of parameter

(

10.2 Communication Detail Setting)

• No hardware error.

(

18. TROUBLESHOOTING)

Touching [OK] button after confirming the result returns to [I/O check].

12

13

14

(2) Self-loopback

Touching [Self] carries out the hardware check of RS-232 interface.

GT14 (Rear face)

1.

For preparation for the self-loopback communication check, insert the connector for self-loopback check

(Customer purchased) shown in the diagram left in the RS-232 interface.

For this connector, short 2 and 3 pins, 7 and 8 pins and 4 and 6 pins, respectively.

Self-loopback check connector

In the communication setting of the GOT utility, set the channel number for the RS-232 interface to 0

([None]).

4 3 2

15

16

8 7 6

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14 - 15

2.

After selecting [Self], the transferred data and received data are verified through the self-loopback connector. When the GOT cannot receive the data during the data transmission, the dialog box shown left appears and the GOT restarts in five seconds.

When the dialog box shown left appears, check the following.

• Check if the pins of the connector for self-loopback check are incorrectly shorted.

• Check if the channel number for the RS-232 interface is set to 0 ([None]) in the communication setting of the GOT utility.

(

10.1.3 Communication setting contents)

• Check if the hardware has no problems.

(

18. TROUBLESHOOTING)

3.

During check, the dialog box shown left is displayed.

4.

When the all checks ended normally, the dialog box shown left is displayed. And the GOT restarts in five seconds.

5.

When an error occurs, the dialog box that shows the

GOT abnormal termination and the byte with the error appears, and then the GOT restarts in five seconds.

When the dialog box shown left appears, check the following.

• Check if the hardware has no problems.

(

18. TROUBLESHOOTING)

14 - 16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.2 Self Check

14.3 System Alarm Display

„

System alarm function

System alarm is the function to display error code and error message when an error occurs in GOT, controller or network.

System alarms can be reset on the System alarm display screen.

For details of system alarm, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

„

Display operation of System alarm display

(

Main menu

9.3 Utility Display)

Debug & self check

9

10

11

Touch

[System alarm display]

12

Touch

[Debug & self check]

System alarm display

Touching [Reset] resets the system alarm display in the

GOT error.

13

14

15

16

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.3 System Alarm Display

14 - 17

„

Operation of system alarm display

(1) System alarm display resetting

1.

Eliminate each cause of the system alarm being occurred.

Error causes can be identified by the error code, error message and channel No. displayed on the

(

System alarm screen.

18. TROUBLESHOOTING)

Touch

2.

A method for resetting system alarm depends on an error.

• GOT error

Touch [Reset] button to reset system alarms.

• CPU error and Network error

The system alarm is automatically reset after its cause is eliminated.

(1) Before resetting the system alarm display in the GOT error

Eliminate the system alarm cause before resetting the system alarm display in the GOT error.

If not eliminated, the system alarm display in the GOT error will not be reset even after the reset operation.

(2) Processings with reset operation

The following data in the system information are also reset.

• GOT error code (Write device)

• GOT error detection signal (System Signal 2-1.b13)

14 - 18

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.3 System Alarm Display

14.4 GOT start time

„

GOT start time function

GOT start time is the function to display the following date and time.

• Start time of GOT

• Current time of GOT

• Operating hours of GOT

„

Display operation of GOT start time

(

Main Menu

9.3 Utility Display)

Touch

[

Debug & self check

]

Start time

Debug & self check

Touch

[

GOT start time

]

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.4 GOT start time

14 - 19

13

14

15

11

12

9

10

16

„

Display of GOT start time

Start Time

Current Time

Item

Operating hours

Description

Displays the time when the GOT was powered on or reset-restarted (OS installation, communication setting change).

Displays the current time.

Displays operating hours of the GOT.

The displayed operating hours is the accumulated time while GOT is powered on or reset-restarted (OS installation, communication setting change).

When powering off or reset-restarting the GOT, the operating hours is cleared.

(1) To display correct time

Set the clock of GOT. (

12.1.1 Time setting and display functions)

When the clock has not been set, the correct time is not displayed at [Start Time] and [Current Time].

(2) Time displayed at [Operating hours]

[Operating hours] is displayed irrespective of [Start Time] and [Current Time].

When changing the clock of the GOT, [Operating hours] does not match with the difference between [Current

Time] and [Start Time].

([Operating hours] is not the time calculated from [Current Time] and [Start Time].)

The time displayed at [Operating hours] is a reference for the accumulated time while GOT is powered on or reset-restarted (OS installation, communication setting change).

14 - 20

14. GOT SELF CHECK (DEBUG AND SELF CHECK)

14.4 GOT start time

15. CLEANING DISPLAY SECTION

(CLEAN)

In utility, the screen can be set as not to be effected by touching the screen when clean with clothes.

To clean the GOT, wipe the dirty part with a soft cloth using neutral detergent.

10

Precautions for cleaning

Do not use chemicals such as thinner, organic solvents and strong acids, since they may cause the protective sheet to be deformed or the dissolvable paint on the surface to peel off.

In addition, do not use spray solvents since they may cause the electrical failure of the GOT and peripheral devices.

„

Display operation of Clean

(

Main Menu

9.3 Utility Display)

Clean

11

12

9

Touch [Clean]

13

14

Even if touch points other than the upper left corner and upper right corner of the screen, the GOT does not operates.

„

Operation of Clean

After cleaning the screen, touch the screen following the instruction displayed.

After touching the screen, the screen returns to the Main Menu.

The following screen is displayed.

15

16

15. CLEANING DISPLAY SECTION (CLEAN)

15 - 1

15 - 2

15. CLEANING DISPLAY SECTION (CLEAN)

16. INSTALLATION OF COREOS,

BOOTOS AND STANDARD MONITOR

OS

10

For executing the GOT utility, install the BootOS and standard monitor OS on the C drive (built-in flash memory) of the

GOT, or set the OS boot drive to [A: Standard SD card] and insert the SD card with OS files into the GOT.

(BootOS is installed in the GOT at factory shipment. It is not necessary to install BootOS when upgrading of it is unnecessary.)

This chapter explains the installation using GOT.

GT Designer3 SD card/ GOT

USB memory

Write

OS file

BootOS or standard monitor OS installation

When GOT is remote, installed easily using the CF card/

USB memory

Install the SD card in GOT

GT Designer3

SD card/USB memory

*1

The GOT can starts without an

OS installed.

Write

OS file

Set the OS boot drive to [A: Standard

SD Card].

SD card

GOT SD card/ GOT

USB memory

OS file upload

*1

Install the SD card in GOT

BootOS or standard monitor OS installation

Install OS from GOT to GOT using CF card/USB memory.

SD card/USB memory

*1

Install the SD card/USB memory in GOT

When execute installation with USB memory, standard monitor OS has to be installed in GOT in advance.

For the writing of OS in GT Designer3, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

11

12

13

14

9

CoreOS

In 16.1 to 16.4 of this chapter, only BootOS and standard monitor OS are described.

For CoreOS, refer to the following.

16.5 CoreOS

15

16

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16 - 1

16.1 BootOS and Standard Monitor OS Required for

Installation

Under-mentioned BootOS and Standard monitor OS are necessary to execute utility.

OS name

BootOS

Standard monitor

OS

Function overview Storage location

Built-in flash memory

C: \G1BOOT\ Required for the control of GOT and the communication between PC and GOT.

Installed at factory shipment.

(BootOS can be installed from GT Designer3 or the SD card. When installed from GT Designer3 or the

SD card, GOT is initialized to be the factory shipment status.)

SD card that stores data with

OS boot drive set to the A drive

A: \G1BOOT\

Required for the GOT operation as the monitoring function of GOT, installation and deletion of the OS file or project data, touch key control or display function of the screen and guidance.

System screen data

System screen management information file

TrueType numerical font

12-dot standard font (Gothic)

16-dot standard font (Mincho)

16-dot standard font (Gothic)

Required for display and operation of the usercreated screen and utility screen.

Not installed in GOT at factory shipment.

Install it from GT Designer3, or the SD card or

USB memory.

At installation, select [Mincho] or [Gothic] for the 16-dot standard font.

Built-in flash memory

C: \G1SYS\

SD card that stores data with

OS boot drive set to the A drive

A: \G1SYS\

16 - 2

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.1 BootOS and Standard Monitor OS Required for Installation

16.2 Prior Preparations for Installing BootOS and

Standard Monitor OS

9

For the installation using GOT, the SD card or USB memory storing BootOS or standard monitor OS is required.

For the method of writing BootOS and standard monitor OS in the SD card or USB memory, the following three methods are available.

(1) [To Memory Card] from GT Designer3

GT Designer3 Version1 Screen Design Manual (Fundamentals)

(2) Uploading from other GOT (BootOS or standard monitor OS has been installed)

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

(3) Using SD card that stores data with OS boot drive set to A drive

GT Designer3 Version1 Screen Design Manual (Fundamentals)

10

11

Precautions on writing BootOS, standard monitor OS in SD card or USB memory

When writing BootOS, standard monitor OS, etc. in the SD card or USB memory, be sure to execute by the utility of other GOT, GT Designer3.

The installation is not executed properly with the SD card or USB memory to which uploaded from the utility of GOT or copied by software other than GT Designer3.

Note the available capacity of the SD card or USB memory.

The available capacity of BootOS and standard monitor OS can be confirmed by [To Memory Card] of GT

Designer3.

12

13

Capacity of standard monitor OS

Available space of the SD card or USB memory

14

15

16

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.2 Prior Preparations for Installing BootOS and Standard Monitor OS

16 - 3

16.3 BootOS and Standard Monitor OS Installation Using

SD card or USB Memory

There are the following two types for the BootOS, standard monitor OS installation using the SD card or USB memory.

(1) Installing when starting the GOT

(

16.3.1 Installing when starting the GOT)

All the OS and project data stored in the SD card or USB memory are transferred to the GOT when powering on the GOT. This installing method is effective in the following cases.

• The GOT utility cannot be displayed.

• The standard monitor OS is not installed.

(2) Installing using the data control function (Utility)

(

16.3.2 Installing using the program/data control function (Utility))

By operating the utility, select OS or project data stored in the SD card or USB memory and transfer them to the

GOT.

Precautions on installing BootOS, standard monitor OS

(1) Installing both BootOS and standard monitor OS

After completing BootOS installation, install standard monitor OS. When installing BootOS, the built-in flash memory in the GOT is initialized and goes to the status at factory shipment. (All OS and project data are erased.)

BootOS is installed in the GOT at factory shipment.

It is not necessary to install BootOS when not upgrading it.

(2) Copying project data using SD card or USB memory

After installing BootOS, standard monitor OS, and other OS, download the project data.

At this time, match the version of the standard monitor OS in the GOT with the version of the standard monitor

OS with which the project data was created.

(3) When OS and project data are in the SD card or USB memory (when using GT Designer3)

When installing by pressing the upper left corner of the GOT screen, project data is downloaded after completion of OS installation.

When installing with the utility, install the OS and download the project data from their respective operation screens.

(4) Installation cannot be interrupted.

Do not perform any of the following during a BootOS or standard monitor OS installation.

Failure to do so may result in installation failure, causing the GOT malfunction.

• Powering off the GOT

• Pressing the reset button of the GOT

• Turning off the SD card access switch of the GOT

• Removing the SD card or USB memory

If the installation failure and the GOT malfunction occur, take the following action.

• If BootOS installation failed: Install CoreOS.

(

16.5.1 Installing the CoreOS)

• If standard monitor OS installation failed: Install BootOS.

(

16.3.1 Installing when starting the GOT)

16 - 4

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory

16.3.1 Installing when starting the GOT

The displayed message is different depending on the installation condition of standard monitor OS. When the screen requesting operation is displayed, operate the GOT according to the instructions on the screen.

„

Operation procedure

(1) When installing with SD card

Now installing BootOS.

Reboot.

1.

Power OFF the GOT, switch the SD card access switch to OFF, and install the SD card where the

BootOS, standard monitor OS or project data is stored in the SD card interface of the GOT.

2.

Switch ON the SD card access switch of GOT.

3.

Power on the GOT while pressing upper left corner of the GOT screen. (1-point press installation function)

4.

The BootOS or standard monitor OS is installed in the built-in flash memory.

The SD card access LED is lit during the install execution.

Do not pull out the SD card or power off the GOT while the SD card access LED is lit.

5.

The GOT restarts automatically after the installation is completed.

(When the standard monitor OS is already installed, the GOT restarts by touching the [OK] button.)

6.

After confirming normal restart, switch off the SD card access switch of the GOT. Confirm that the card access LED is not lit, and remove the SD card from the SD card interface of the GOT.

9

10

11

12

13

14

15

16

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory

16 - 5

(2) When installing with USB memory

Now installing BootOS.

Reboot.

1.

Power off the GOT, and install the USB memory where the BootOS, standard monitor OS or project data is stored in the USB interface of the GOT.

The BootOS cannot be stored in the USB memory where the standard monitor OS or project data is stored.

2.

Power on the GOT while pressing upper left corner of the GOT screen. (1-point press installation function)

3.

The BootOS or standard monitor OS is installed in the built-in flash memory.

Do not pull out the USB memory or power off the

GOT while install execution.

4.

The GOT restarts automatically after the installation is completed.

(When the standard monitor OS is already installed, the GOT restarts by touching the [OK] button.)

5.

After confirming normal restart, remove USB memory from the USB interface of the GOT.

For removing methods of the USB memory, refer to the following.

13.2.9 USB device status display

(1) Drives to be used

When installing OS at power-on, use the A or E drive.

(2) Installation by pressing upper left corner of the GOT screen

When the OS boot drive is set to the A or E drive, installation by pressing upper left corner of the GOT screen is not available.

16 - 6

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory

16.3.2 Installing using the program/data control function (Utility)

For details on program/data control function, refer to the following.

13. FILE DISPLAY AND COPY (PROGRAM/DATA CONTROL)

9

10

Precaution on executing program/data control function

When execute program/data control function, standard monitor OS has to be installed in GOT in advance. Thus, this function cannot be used for the initial installation of standard monitor OS after purchasing GOT.

Install standard monitor OS by the following two methods.

(1) GT Designer3

(2) Installing when starting the GOT

„

Operation procedure

(1) When installing with SD card

1.

Power OFF the GOT. After SD card access LED is off, install the SD card in which BootOS, standard monitor OS or project data is stored in the SD card interface of GOT.

2.

Switch ON the SD card access switch of GOT.

3.

Display the program/data control function screen (Utility) on the GOT, and install BootOS, standard monitor OS from the SD card to GOT.

11

12

13

Touch [Install]

Now installing BootOS.

Reboot.

4.

The SD card access LED is lit during the install execution.

Do not pull out the SD card or power off the GOT while the SD card access LED is lit.

5.

The GOT restarts automatically after the installation is completed.

6.

After confirming normal restart, switch off the SD card access switch of the GOT. Confirm that the card access LED is not lit, and remove the SD card from the SD card interface of the GOT.

14

15

16

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory

16 - 7

(2) When installing with USB memory

1.

Install the USB memory in which BootOS, standard monitor OS or project data is stored in the USB interface of GOT.

2.

Display the data control function screen (Utility) on the GOT, and install BootOS, standard monitor OS.

Touch [Install]

Now installing BootOS.

Reboot.

3.

Do not pull out the USB memory or power off the

GOT while install execution.

4.

The GOT restarts automatically after the installation is completed.

5.

After confirming normal restart, display the USB device status screen and remove the USB memory from the USB interface of GOT.

13.2.9 USB device status display

16 - 8

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.3 BootOS and Standard Monitor OS Installation Using SD card or USB Memory

16.4 When Installing the Different Version of BootOS,

Standard Monitor OS

„

BootOS installation

When installing BootOS, GOT compares the version of the BootOS to be installed with the version of BootOS which is already installed.

If the major version of BootOS to be installed is old, execute the following operations to prevent it from being rewritten.

(When installing from GT Designer3, a message is displayed on the PC screen. Follow the instructions in that message.)

(1) When only BootOS is stored in the SD card or USB memory

1.

The message indicating disabled installation is displayed.

2.

Touch the [OK] button to cancel installation.

After canceling installation, restart the GOT.

9

10

11

12

(2) When BootOS, standard monitor OS, and other OS are stored in the SD card or USB memory

1.

Skip the BootOS installation and install standard monitor OS and other OS.

If the standard monitor OS is already stored on the

GOT, the following message is displayed.

2.

Touching the [OK] button executes installation.

Touching the [Cancel] button cancels installation.

After executing or canceling installation, restart the

GOT.

13

14

(3) When the version is the same or newer regardless of the data stored in the SD card or USB memory

(conditions (1) and (2) above)

1.

The version information and a dialog for selecting whether or not to continue installation are displayed.

2.

Touching the [OK] button executes installation.

Touching the [Cancel] button cancels installation.

After executing or canceling installation, restart the

GOT.

15

16

(GOT screen when BootOS is installed from SD card or USB memory)

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.4 When Installing the Different Version of BootOS, Standard Monitor OS

16 - 9

„

Standard monitor OS installation

Match the version of each OS file when installing standard monitor OS.

Standard monitor OS cannot be installed if the version of each OS file does not match.

(When the installation process is discontinued.)

Standard monitor OS : 1. .

Communication driver : 2. .

Optional function OS : 2. .

(When the installation process is normally executed.)

Standard monitor OS : 2. .

Communication driver : 2. .

Optional function OS : 2. .

Please match the number.

Checking method of BootOS, standard monitor OS version

• Check the version of BootOS or standard monitor OS installed in GOT at [OS information] of the utility.

For details, refer to the following.

13.2.1 OS information

• Check the version of BootOS installed in GOT at product shipment on the rating plate on GOT rear face.

When the Boot OS version is 2 digits, only the lower digit is printed.

AA

BootOS version

HD

BootOS

Version

Example H/W version: H

Boot OS version: AD

Rating plate: HD

16 - 10

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.4 When Installing the Different Version of BootOS, Standard Monitor OS

16.5 CoreOS

Install CoreOS only when the GOT will not be the status of factory shipment even when BootOS is installed.

Normally, the CoreOS has not to be installed.

9

Precautions for installing CoreOS

When executing the CoreOS installation once, it cannot be canceled on the way.

Do not attempt the following to cancel the installation on the way. The GOT may not operate.

• Powering off the GOT

• Pressing the reset button of the GOT

If the GOT does not operate, please consult your local Mitsubishi (Electric System) Service center or representative.

10

11

If the GOT does not recover even when installing the CoreOS, the error may be caused by a hardware failure.

Please consult your local Mitsubishi (Electric System) Service center or representative.

12

16.5.1 Installing the CoreOS

„

Before installing the CoreOS

(1) Installing procedure

The CoreOS can be installed only when using a SD card.

Installation via USB memory/USB/Ethernet is not available.

(2) Boot OS

When installing the CoreOS, the latest BootOS is also installed automatically.

(Operation by the user is not required.)

13

14

15

16

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.5 CoreOS

16 - 11

„

Installing the CoreOS

1.

Write the CoreOS from GT Designer3 to the SD card.

For details of GT Designer3 operation, refer to the following manual.

GT Designer3 Version1 Screen Design

Manual (Fundamentals)

2.

After confirming that the GOT is powered off, install the SD card in the GOT. After installing, switch the

SD card access switch on.

3.

Powering the GOT on displays the screen on the left.

To cancel the installation, power the GOT off and remove the SD card.

4.

Turning the SD card access switch off executes

CoreOS installation.

5.

When the installation is completed, the dialog as shown on the left is displayed.

(The POWER LED of the GOT blinks (green/ orange) at the installation completion.)

6.

Confirm that the message is displayed and power the GOT off.

7.

Remove the SD card after powering the GOT off.

8.

Powering the GOT on again displays the screen as shown on the left.

(The GOT goes to the status of factory shipment.)

Install OS (Standard monitor OS, communication driver, etc.) or download project data as required.

16 - 12

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.5 CoreOS

16.5.2 When the CoreOS cannot be installed

When the CoreOS cannot be installed, confirm the following item.

If the CoreOS cannot be installed even after checking the following item, the error may be caused by a hardware failure.

Please consult your local Mitsubishi (Electric System) Service center or representative.

The message is displayed on the GOT

GOT error.

Error

The CoreOS installation is not executed even when installing the SD card in the GOT.

Contact your local sales office.

SD card error.

Check whether the SD card can be used.

Installation will be cancelled.

GOT type and OS version do not match.

Installation will be cancelled.

The version of OS is not acceptable to this GOT.

Installation will be cancelled.

Confirm the version of OS.

Memory card access switch is off.

Installation will be cancelled.

Turn on the switch and restart the GOT.

Action

(1) Check whether the SD card access switch of the GOT is on.

If the switch is off, switch it on.

(2) The writing from the GT Designer3 to the SD card may not have been completed normally.

Execute the writing from the GT Designer3 to the SD card again.

The GOT main unit is broken.

Please consult your local Mitsubishi (Electric System) Service center or representative.

The SD card is defective.

(1) Format the SD card and re-execute.

(2) Replace the SD card.

The GOT type selected at [Core OS write] of the GT Designer3 is not correct.

Confirm the GOT type and perform [Core OS write] again.

Install CoreOS from the latest GT Designer3.

The SD card access switch is off. Turn the switch on and restart the GOT.

9

10

11

12

13

14

15

16

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.5 CoreOS

16 - 13

16 - 14

16. INSTALLATION OF COREOS, BOOTOS AND STANDARD MONITOR OS

16.5 CoreOS

17. MAINTENANCE AND INSPECTION

17

[STARTUP AND MAINTENANCE

PRECAUTIONS]

DANGER

• When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

• Connect the battery correctly.

Do not discharge, disassemble, heat, short, solder or throw the battery into the fire.

Incorrect handling may cause the battery to generate heat, burst or take fire, resulting in injuries or fires.

• Before starting cleaning or terminal screw retightening, always switch off the power externally in all phases.

Not doing so can cause the unit to fail or malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

[STARTUP AND MAINTENANCE

PRECAUTIONS]

CAUTION

• Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

• Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

• The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault.

• When unplugging the cable connected to the unit, do not hold and pull the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable connection fault.

• Before touching the unit, always touch grounded metal, etc. to discharge static electricity from human body, etc.

Not doing so can cause the unit to fail or malfunction.

[DISPOSAL PRECAUTIONS]

CAUTION

• When disposing of the product, handle it as industrial waste.

18

The GOT does not include consumable components that will cause the shorten life.

However, the battery, liquid crystal display screen and backlight have each life length.

It is recommended to replace the battery periodically.

(For the replacement of the liquid crystal screen and backlight, please consult your nearest sales office or FA center.)

For the life of the liquid crystal display screen or backlight, refer to the following.

3.2 Performance Specifications

17. MAINTENANCE AND INSPECTION

17 - 1

17.1 Daily Inspection

„

Daily inspection items

No.

Inspection Item

1 Installation status of GOT

Inspection Method

Check for loose mounting screws.

Retighten screws with screwdriver.

Criterion

Securely mounted

Action

Retighten screws within the specified torque range.

2

Loose terminal screws

Connection status

Proximate solderless terminals

Loose connectors

Visual check

Not loose

Proper intervals

Retighten terminal screws.

Correct.

Visual check Not loose Retighten connector fixing screws.

3

Dirt on protection sheet Visual check Not outstanding Replace with new one.

Usage status

Foreign material attachment

Visual check No foreign matter sticking Remove, clean.

For the model names of the protection sheet or the replacement procedure, refer to the following.

8.4 Protective Sheet

17.2 Periodic Inspection

„

Yearly or half-yearly inspection items

The following inspection should also be performed when equipment has been moved or modified or the wiring changed.

No.

Inspection Item Inspection Method Criterion

Display section

0 to 50

Action

1

Ambient temperature

Surrounding environment

Ambient humidity

Atmosphere

Make measurement with thermometer or hygrometer.

Measure corrosive gas.

Other portions

10 to 90%RH

No corrosive gas

0 to 55

For use in control panel, temperature inside control panel is ambient temperature.

2 Power supply voltage check

24VDC Measure voltage across terminals.

20.4 to 26.4VDC

Change supply power.

Move module.

Should be mounted firmly.

Retighten screws.

3

4

Looseness

Mounting status

Connection status

Foreign material attachment

Loose terminal screws

Proximate solderless terminals

Loose connectors

Visual check

Retighten screws with screwdriver.

Visual check

No foreign matter sticking

Not loose

Proper intervals

Remove, clean.

Retighten terminal screws.

Correct.

Retighten connector fixing screws.

5 Battery

Visual check Not loose

Check GOT internal battery voltage status in [Time Setting & Display] of the

Utility.

(

12.1.1 Time setting and display functions)

No alarm displayed

Replace with new battery when the current battery has reached the specified life span, even if battery voltage is not displayed.

17 - 2

17. MAINTENANCE AND INSPECTION

17.1 Daily Inspection

17.3 Cleaning Method

Use the GOT always in a clean condition.

To clean the GOT, wipe the dirty part with a soft cloth using neutral detergent.

For the display operation of the [Clean] screen, refer to the following.

15. CLEANING DISPLAY SECTION (CLEAN)

Clean

17

18

Precautions for cleaning

Do not use chemicals such as thinner, organic solvents and strong acids, since they may cause the protective sheet to be deformed or the dissolvable paint on the surface to peel off.

In addition, do not use spray solvents since they may cause the electrical failure of the GOT and peripheral devices.

17. MAINTENANCE AND INSPECTION

17.3 Cleaning Method

17 - 3

17.4 Battery Voltage Low Detection and Battery

Replacement

„

Low battery voltage detection and replacement

Battery contains the data for notifying the maintenance timing and current time.

It is recommended that you replace battery periodically.

For the replacement procedure, refer to the following.

8.3 Battery

The battery voltage low detection can be confirmed by the utility screen and system alarm.

For details of the battery status display by the utility screen, refer to the following.

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

By using system alarm, the message that notifies the battery voltage has decreased can be displayed at the battery voltage low on the screen of the GOT.

To display the message in the system alarm, set [Battery alarm display] to on.

11.1.1 Function of Display

System alarm

500 Warning! Built-in battery voltage is low.

For details of the system alarm display, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

Battery replacement timing

When detecting voltage low, replace the battery immediately.

Data can be saved for about one month after the battery voltage low detection and cannot be saved after that.

If it exceeds a month from the voltage low detection to battery replacement, the clock data or D-drive (Internal

SRAM) data may become indefinite.

Adjust the clock and format the D drive (Internal SRAM).

17 - 4

17. MAINTENANCE AND INSPECTION

17.4 Battery Voltage Low Detection and Battery Replacement

17

Example of alarm output to external device (lamp, buzzer, etc.)

The following describes an example of outputting the battery voltage low signal from a FX series PLC to an external device with system information.

Condition: The Write Device is "D20" and all data is used (the button is clicked on the setting screen of drawing software) for the system information assignment.

D36 b12: Battery voltage low (System Signal 2-2)

Turned on upon a battery voltage drop.

Used as shown below in the sequence program.

RUN monitor

M8000

MOV D36 K4M20

Battery voltage low

M32

Y***

Output to external device of PLC

Activated the output upon battery voltage low detection.

"*" indicates the output number at which the external device is connected.

For details of system information, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

18

17. MAINTENANCE AND INSPECTION

17.4 Battery Voltage Low Detection and Battery Replacement

17 - 5

„

Handling of Batteries and Devices with Built-in Batteries in EU Member States

This section describes the precautions for disposing of waste batteries in EU member states and exporting batteries and/or devices with built-in batteries to EU member states.

(1) Disposal precautions

In EU member states, there is a separate collection system for waste batteries. Dispose of batteries properly at the local community waste collection/recycling center.

The following symbol is printed on the batteries and packaging of batteries and devices with built-in batteries used for Mitsubishi Graphic Operation Terminal (GOT).

Symbol

This symbol is for EU member states only.

The symbol is specified in the new EU Battery Directive (2006/66/EC) Article 20 "Information for end-users" and

Annex II.

The symbol indicates that batteries need to be disposed of separately from other wastes.

(2) Exportation precautions

The new EU Battery Directive (2006/66/EC) requires the following when marketing or exporting batteries and/or devices with built-in batteries to EU member states.

• To print the symbol on batteries, devices, or their packaging

• To explain the symbol in the manuals of the products

(a) Labeling

To market or export batteries and/or devices with built-in batteries, which have no symbol, to EU member states on September 26, 2008 or later, print the symbol shown in (1) on the GOT or their packaging.

(b) Explaining the symbol in the manuals

To export devices incorporating Mitsubishi Graphic Operation Terminal to EU member states on September

26, 2008 or later, provide the latest manuals that include the explanation of the symbol.

If no Mitsubishi manuals or any old manuals without the explanation of the symbol are provided, separately attach an explanatory note regarding the symbol to each manual of the devices.

The requirements apply to batteries and/or devices with built-in batteries manufactured before the enforcement date of the new EU Battery Directive (2006/66/EC).

17 - 6

17. MAINTENANCE AND INSPECTION

17.4 Battery Voltage Low Detection and Battery Replacement

17.5 Backlight Shutoff Detection

17

The backlight is built into GOT for the liquid crystal display.

When GOT detects backlight shutoff, the POWER LED blinks green/orange alternately.

The brightness of the backlight decreases with the lapse of usage period. When backlight shutoff is detected or the display becomes unclear, replace the backlight. (GT14 requires LED replacement.)

For replacement of the backlight, contact your nearest sales office or FA Center.

(1) Life of backlight

The usable duration of backlight can be extended by setting to "Screen saving backlight off" in the utility of GOT

(GOT set up). For details, refer to the following.

11. DISPLAY AND OPERATION SETTINGS (GOT SET UP)

17.5.1 Backlight shutoff detection and external alarm

18

When the GOT detects a backlight shutoff, the system information set with drawing software is turned on.

You can issue a backlight shutoff of the GOT from the PLC to external devices (such as the lamp or buzzer), using system information.

To avoid any screen touch operation by the user who misunderstands it is in screen saving mode, install an external alarm and interlock the loads that would cause danger.

For details of the system information, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

Example of alarm output to external device (lamp, buzzer, etc.)

The following provides an example of outputting the backlight shutoff detection signal from a FX Series PLC to an external device, using system information.

Condition: The Write Device is "D20" and all data is used (the button is clicked on the setting screen of drawing software) for the system information assignment.

D36 b14: Backlight shutoff detection (System Signal 2-2)

Turned on upon a backlight shutoff.

Used as shown below in the sequence program.

RUN monitor

M8000

MOV D36 K4M20

Backlight shutoff detection

M34

Y***

Output to external device of PLC

Activated the output upon backlight shutoff detection.

"*" indicates the output number at which the external device is connected.

Precautions for the backlight shutoff status

In the backlight shutoff status, the touch key operates.

Early replacement of backlight is recommended.

17. MAINTENANCE AND INSPECTION

17.5 Backlight Shutoff Detection

17 - 7

17 - 8

17. MAINTENANCE AND INSPECTION

17.5 Backlight Shutoff Detection

18. TROUBLESHOOTING

17

This chapter explains the GOT restoration sheet and the error message/system alarm list.

18.1 GOT Restoration Sheet

This section provides restoration methods for the case the GOT does not operate normally, which are listed in check sheets.

The following explains how to use each sheet.

(1) When the GOT does not operate or malfunctions (GOT status check sheet)

When the GOT does not operate or malfunctions, identify the cause of the malfunction etc. with GOT status check sheet and take corrective action.

When the GOT is restored, see the status for a while.

(2) When the wiring status needs to be improved (GOT installation status check sheet)

When the noise caused by the GOT wiring status is considered to have caused the malfunction, etc. based on the check result of (1) above, take corrective action for wiring using GOT installation status check sheet.

When the GOT is restored, see the status for a while.

(3) When corrective action other than (1) and (2) above is required (System configuration check sheet)

If malfunction etc. occurs even after checking with (1) and (2) above, please contact your local Mitsubishi

(Electric System) Service after filling out System configuration check sheet with details about your system.

When sending a troubled product, attach the GOT restoration sheets (GOT status check sheet, GOT installation status check sheet, System configuration check sheet) checked in this section.

Please keep copies of the restoration sheets.

18

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

18 - 1

„

GOT status check sheet

Check the GOT starting from (1) GOT status.

Proceed as instructed by "Action".

(1) GOT status

Phenomenon Cause/status

(a) Frequency when the GOT does not operate, an error occurs on the screen, etc.

Occurs always.

Occurs sometimes.

Occurrence frequency:

( )

Example: Once a month

(b) Checking of the displayed error code (system alarm)

Proceed to (1)-(b).

Action

Can be checked.

Error code (system alarm):

( )

Example: 460 Communication unit error

Take the action for the error code (system alarm) or error message checked.

If the status does not change after the action is taken, proceed to (1)-(c).

Proceed to (1)-(c).

Cannot be checked.

(c) POWER LED

Lit in green

Lit in orange

Blinks in green/orange

Not lit

The power is supplied normally.

Screen saving is being performed.

The read device of the system information may have been turned ON when the device was set, and the screen was switched to the forced screen saving status.

Proceed to (1)-(d).

Check the setting of the read device.

When no problem is found in the setting, proceed to (1)-(d).

The backlight has run out.

Replace the backlight.

If the GOT is not restored, proceed to (1)-

(d).

The power is not supplied.

When the power is supplied, the GOT hardware may be faulty.

Check if the power is supplied. If the GOT is not restored, proceed to (5) Troubled product investigation.

(d) Screen display

The screen is completely black.

The screen is completely white.

A line is displayed on the screen.

Other faulty displays

The liquid crystal display or BootOS may be faulty.

The GOT hardware may be faulty.

Perform the following in order.

1) Reinstalling BootOS

2) Reinstalling standard monitor OS

If the GOT is not restored by 1) and 2), perform the following.

3) Reinstalling CoreOS and then standard monitor OS

If the GOT is not restored by the above operations, proceed to (5) Troubled product investigation.

Proceed to (5) Troubled product investigation.

The GOT hardware may be faulty.

Example: A vertical line is displayed.

Proceed to (5) Troubled product investigation.

The screen freezes.

The screen display is not updated and any operation is not allowed.

Proceed to (1)-(e).

18 - 2

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

Phenomenon

(e) Buzzer sound

Does not sound.

Continues to beep randomly.

Continues to beep in a particular pattern.

Beeps continuously.

Cause/status Action

Buzzer sound:

( )

Example: The rhythm as three beeps, one beep, and then two beeps is repeated.

Proceed to (2) Status of the GOT when it freezes.

The read device of the system information may have turned ON when the device was set, turning

ON the Buzzer output signal.

Check the setting of the read device.

When the Buzzer output signal has no error, proceed to (2) Status of the GOT when it freezes.

(2) Status of the GOT when it freezes (screen operation stopped)

Phenomenon Cause/status

(a) Switching to the utility

Action

Enabled

Error code (system alarm):

( )

Example: 460 Communication unit error

When the system alarm display function can be used, take the action for the error code

(system alarm) displayed.

If the action cannot be taken, proceed to (2)-

(b).

Disabled

The system alarm display function cannot be used.

(b) Executing of I/O check from the GOT utility

Communication error

No error

Display details:

( )

Example: A message indicating the cause may be a connection error was displayed.

The hardware such as a communication interface has no error.

(c) Objects not displayed on the monitor screen

Proceed to (2)-(c).

Proceed to (2)-(c).

Proceed to (3) Status of the PLC CPU.

Found

Not found

Details:

( )

Example: The numerical display object is not displayed.

Proceed to (3) Status of the PLC CPU.

(3) Status of the PLC CPU

Phenomenon

(a) PLC failure

Occurs always.

Cause/status

An error such as CONTROL-BUS. ERROR or SP.

UNIT LAY. ERROR may have occurred.

Error code (system alarm):

( )

Example: 1204 CPU H/W fault

The PLC CPU may be influenced by noise or the hardware may be faulty.

Action

Proceed to the following.

18.1

Occurs sometimes.

Operates normally.

Occurrence frequency:

( )

Example: Once a month

Error code (system alarm):

( )

Example: 1204 CPU H/W fault

-

Proceed to (4) GOT restoration procedure.

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

18 - 3

17

18

(4) GOT restoration procedure

Follow the procedures below starting from (a) and in order to check if the GOT is restored.

If the GOT is not restored, proceed to the next item.

Cause Action Check item

(a) Press the GOT reset switch.

Restored

Not restored (Proceed to (b).)

(b) Power the GOT ON/OFF.

*1

Restored

Not restored (Proceed to (c).)

(c) Reset or power ON/OFF the PLC

CPU.

Restored

Not restored (Proceed to (d).)

(d) Power the GOT and PLC CPU ON/

OFF simultaneously.

Restored

Not restored (Proceed to (e).)

(e) Connect the cable again.

Restored

Not restored (Proceed to (f).)

(f) Reinstall the project data.

Restored

Not restored (Proceed to (g).)

(g) Reinstall the OS.

Restored

Not restored (Proceed to (h).)

(h) Take the action described in the

"Action" column.

Restored

Not restored (Proceed to (i).)

(i) The GOT is not restored even by performing (a) to (h).

The GOT may have malfunctioned temporarily due to noise.

The cable connection may be faulty.

Data may have been destroyed by an action such as powering the GOT OFF during the installation of project data or

OS.

The GOT may have malfunctioned temporarily due to noise.

-

Take the action of (4)-(h).

Securely connect the cable.

If an error occurs again, proceed to (5)

Troubled product investigation.

Do not power the GOT OFF while transferring data.

If an error occurs again, proceed to (5)

Troubled product investigation.

Take the action with referring to GOT installation status check sheet.

Proceed to (5) Troubled product investigation.

*1 When powering the GOT ON again (OFF ON), power OFF the PLC before that.

(5) Troubled product investigation

When malfunction of the GOT is not improved, please contact your local Mitsubishi (Electric System) Service.

Depending on the problem details, we may ask you to return the troubled product to us.

In that case, please attach the GOT status check sheet, GOT installation status check sheet, and the system configuration check sheet filled out with details of your system.

18 - 4

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

„

GOT installation status check sheet

Check the current installation status of the GOT you are using against the GOT installation status described in the upper column of items (1) to (7).

When the measure described in the lower column is needed, take the measure for the current status.

When the measure is taken, check the result, "Effective" or "Ineffective".

(1) Panel inside wiring

17

18

NFB

Current status

The power line connected to the power or servo amplifier and the communication cable are mixed in the duct.

Mixed

Not mixed

MC MC RA RA

Measure for the cables mixed

NFB

MC MC RA RA

Wiring the power line and communication cable in the panel without mixing them in the duct can reduce the influence of noise.

Effective

Ineffective

(2) Panel outside wiring

Current status

Fig. A

Measure for the cables installed together

Fig. B

Power line

The power line and communication cable are installed together.

Installed together

Not installed together

Communication cable

Power line

100mm or more

Power line

Communication cable

Wiring duct

Signal line

Power line

Separator

Communication cable

Leading the power line and communication cable outside the panel at separate places can make the communication cable less influenced by noise from the power line. Installing the communication cable apart from the power line or using a separator (made of metal) in the duct as shown in Fig. B can make the communication cable less influenced by noise.

Effective

Ineffective

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

18 - 5

(3) Wiring of GOT's FG cable and power line

GOT

Current status

FG

The FG cable and power line of the GOT are installed together.

Installed together

Not installed together

Power for the power equipment

GOT

Measure for the cables installed together

FG

Separating the FG cable and power line of the GOT in wiring reduces the influence of noise.

Effective

Ineffective

(4) Surge measures

Current status

PLC

Output

Power for the power equipment

AC

C

R

L

A surge suppressor is used for the wiring of the load such as MCCB, electromagnetic contactor, relay, solenoid valve, or induction motor.

(When a surge suppressor is used, fill out the entry area below with the surge suppressor model name and the name of the equipment for which the surge suppressor is used.)

Used

Not used

Measure for the equipment without a surge suppressor used

PLC

Output

C

R

L

AC

The surge suppressor must be attached close to the load

Attaching the surge suppressor on the cable close to the load can reduce the influence of surge on the GOT.

Entry area

Model name of the surge suppressor Equipment name

Effective

Ineffective

18 - 6

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

Current status

17

(5) Grounding status

Servo

CN1A CN1B

CN2 CN3

FG

LG

PLC

FG a

Panel grounding

Connection cable

GOT

FG

Panel grounding

The FG cables of the control equipment (such as PLC) and the power equipment (such as servo amplifier) are connected as shown by "a".

Connected

Not connected

18

Measure for the FG cables connected

Fig. A

Fig. B

Servo

CN1A CN1B

CN2 CN3

FG

FG

LG

PLC

Connection cable

Terminal block

Panel grounding

GOT

FG

Terminal block

Panel grounding

Grounding for power system

Grounding for power system

Servo

CN1A CN1B

CN2 CN3

FG

FG

PLC

LG

Panel grounding

Connection cable

GOT

FG

Panel grounding

Perform independent grounding at two places as shown in Fig. A.

Independent grounding can reduce the influence of noise.

If independent grounding is not allowed, be sure to perform shared grounding as shown in Fig. B.

Effective

Ineffective

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

18 - 7

(6) Grounding status of the panel on which the GOT is installed

Connection cable

GOT

Current status Ground cable led from the panel having the control equipment

FG

A single ground cable is led from the panel having the control equipment such as PLC to the panel having the

GOT.

Led

Not led

Fig. A

Ground cable

Use a short and thick wire as possible.

Connection cable

GOT

FG

Ground to the panel.

Measure for the ground cable led

Fig. B

Ground cable

Connection cable

GOT

FG

Ground to the panel.

Connection cable

Fig. C

Ground cable

Use a short and thick wire as possible.

GOT

FG

Ferrite core

Ground to the panel.

Fig. D Ground cable

Connection cable

GOT

FG

Ferrite core

Ground to the panel.

Connecting the ground cable to the panel having the GOT as shown in

Fig. A to reduce the potential difference may prevent the malfunction.

When wiring as shown in Fig. A is difficult, perform wiring as shown in

Fig.B.

Effective

Ineffective

Attaching the ferrite core to the ground cable connected to the panel having the GOT as shown in Fig. C reduces the influence of noise.

When wiring as shown in Fig. C is difficult, perform wiring as shown in

Fig. D.

Effective

Ineffective

18 - 8

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

(7) Power supply system

Current status

Main power

AC200V

PLC power

PLC

GOT

I/O power

Main circuit power

I/O equipment

Power equipment

The power from the same system is used for the GOT, I/O equipment (such as relay), and power equipment (such as servo amplifier).

Used

Not Not used

Measure for the equipment for which the power from the same system is used

Main power

AC200V

Isolation transformer

PLC power

PLC

GOT

I/O power

Main circuit power

I/O equipment

Power equipment

Connecting an isolation transformer as well as separating the wiring of the GOT power from that of the power of the I/O equipment and power equipment reduces the influence of noise.

Effective

Ineffective

17

18

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

18 - 9

„

System configuration check sheet

Fill in the brackets with the unit/module name.

(1) System configuration of the GOT

(a) GOT main unit

(b) Communication interface

(c) Cable between the PLC and GOT

(d) Cable length

(2) System configuration of the PLC

(a) Power supply module

(b) CPU module

(c) Serial communication unit/computer link module

(d) Network module

(e) Interrupt module

(f) Positioning module

Used

Not used

Used

Not used

Used

Not used

Used

Not used

(g) Number of extension stages

(h) If any other module etc. is used, please describe it.

[ ]

[ ]

[ ]

[ m]

[ ]

[ ]

[ ]

[ ]

[ ]

[ ]

[ stages]

Entry area for recurrence (when the malfunction occurred after the action is taken)

(3) Describe the operation situation when freezing of the screen or faulty display of the GOT has reoccurred.

18 - 10

18. TROUBLESHOOTING

18.1 GOT Restoration Sheet

18.2 Error Message and System Alarm

17

This chapter describes the error message and system alarm displayed in the GOT.

As the error code and error message displaying functions when an error occurs at the GOT, controller or network, there are two kinds: system alarm and advanced system alarm.

For details of the system alarm and advanced system alarm, refer to the following.

GT Designer3 Version1 Screen Design Manual (Functions)

18

Error code and channel No.

• Error codes can also be confirmed in the error code storage area of the system information function.

• The channel No. where an error is occurring can be confirmed with the GOT special register (GS262 to 264).

For details of the system information and GOT special register, refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

18.2.1 Error contents display

This section describes the example for displaying error code and error message on GOT.

„

Popup-displaying the error code and error message (Advanced alarm popup display

(System alarm))

If an error occurs, the error code and error message can be popup-displayed on the front of the monitor screen.

As alarms are popup-displayed regardless of the screen type, the error occurred will not be overlooked.

A 1254

B 348

A 1254

B 348

04/6/1 13:20 Power module

Pop up generated alarms regardless of the screen.

„

Displaying error code and error message in a list (Advanced system alarm display)

If error has occurred, error code and error message can be displayed on the list set with the screen.

Multiple errors can be displayed, or the history of display can be recorded.

Occurred

04/6/1 10:25

04/6/1 8:05

Message

Temp. error

Fuse error

Restore Check

11:25 10:45

Create a screen to display alarms, and confirm the details of the alarms and take measures.

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

18 - 11

„

Checking error messages with the utility (Utility)

The error code and error message can be checked with the system alarm display of the utility when the object is not set.

14.3 System Alarm Display

Error code and reference manual

Error source

Controller

GOT

*5

Network

CPU

Motion controller

CNC C70

Robot controller

Servo amplifier

*3

Error code Description

Channel No. storage destination

*1

0 to 99

(Value of D9008)

Error code of CPU (for ACPU)

100 to 299

300 to 399

400 to 499

500 to 699

800 to 999

1000 to 10000

(Value of SD0)

10001 to 10999

11000 to 11999

12000 to 12999

Error code of the following controllers

FXCPU

*2

Third party PLC

Temperature controller

(OMRON temperature controller only)

Error code of the GOT main unit function

Error code of the GOT communication function

Error code of the GOT main unit function

Error code of network

Error code of CPU

(for QCPU, QnACPU)

Error code of Motion controller

(Q173DCPU/Q172DCPU)

Error code of CNC (Q173NCCPU)

Error code of Robot controller

(Q172DRCPU)

GS263

GS262

*4

GS264

GS263

20016 to 20237 Error code of servo amplifier

Reference

User's manual of the ACPU connected with GOT

User's manual of the controller connected with the GOT

Deal with errors according to the error messages.

18.2 Error Message and System Alarm

User's manual of the QCPU and QnACPU connected with

GOT

User's manual of the Motion controller connected with GOT

User's manual of the CNC C70 connected with GOT

User's manual of the Robot controller connected with GOT

User's manual of the servo amplifier connected with GOT

*1 For details of GOT special registers (GS262 to 264), refer to the following manual.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

*2 The assigned error code for FXCPU is 100 to 109, which displays the status of M8060 to M8069.

(Example) When the error code (100) error occurs, correct the error according to the M8060 description.

*3 The error code displayed on GOT is calculated by changing the error code (Hexadecimal) displayed on the servo amplifier to the decimal number and adding 20000 to it.

*4

When referring to the manual of servo amplifier by the error code displayed as a GOT system alarm, subtract 20000 from the

GOT error code and change its lower three digits to the hexadecimal number.

(Example: When GOT system alarm is 20144, the error code of servo amplifier becomes 90

H

.)

Channel No. will not be stored depending on the error code.

For channel No. storage availability for each error code, refer to the following.

18.2.2 List of error message/system alarm

*5 An alarmed drive cannot be confirmed in the system alarm regarding file access; however, it can be specified by confirming the file access error signal (b7 to 10) of system signal 2-2.

18 - 12

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

18.2.2 List of error message/system alarm

The system alarm detected with GOT is shown below.

Error code

Error message

303

Set monitor points too large.

Decrease setting points.

Action

Decrease the number of objects from the displayed screen.

For the number of maximum objects for 1 screen, refer to the following.

GT Designer3 Version1 Screen Design Manual (Fundamentals)

304

306

307 Monitor device not set

308

309

No comment data.

Download comment.

Device reading error.

Correct device.

310

Project data does not exist or out of range.

311

312

315

316

317

320

322

Set trigger points too large.

Decrease setting points.

No project data.

Download screen data.

No. of alarm has exceeded upper limit.

Delete restored alarm.

No. of sampling has exceeded upper limit.

Delete collected data.

Device writing error.

Correct device.

Cannot display or input operation value.

Review expression.

Too high frequency of data collection.

Review conditions.

Specified object does not exist or out of range.

Dedicated device is out of range.

Confirm device range.

The number of objects using Sampling/Cycle during ON/Cycle during

OFF exceeds 100.

Decrease the number of objects.

The project data is not downloaded or the screen data is not sufficient.

Download the project data or screen data.

The monitor device of the object is not set.

Set the monitor device of the object.

The comment file does not exist.

Create the comment file and download to GOT.

The error occurred when reading a continuous device.

Correct the device.

• Specified base screen / window screen does not exist in the project data.

• Specified base screen / window screen is out of the permissible area.

Specify the existing base screen / window screen.

The number of alarm histories that can be observed by the alarm history display function has exceeded the maximum points.

Delete the restored history to decrease the number of alarm histories.

The collection frequency exceeded the upper limit when "Store Memory" and "Accumulate/Average" were set in the scatter graph.

• Approve "Clear trigger" setup in the scatter graph.

• Set the "Operation at frequency over time" to "Initialize and Continue" in scatter graph.

Error occurred while writing in the device.

Correct the device.

In indirect specification of comment/parts number, the data operation result exceeded the range in which device type can be expressed.

Review the data operational expression, in order not exceeding the range in which the device type can be expressed.

Data of an object, to which [Collect data only when trigger conditions are satisfied] is set, are collected too frequently, or the number of objects has exceeded the number of objects collectable simultaneously.

Set a longer cycle for trigger occurrence to each object.

Make the settings so that 257 or more display triggers of objects, to which

[Collect data only when trigger conditions are satisfied] is set, do not occur simultaneously.

The part file does not exist.

Create the part file and download to GOT.

The monitored device No. is out of the permissible area of the targeted

PLC CPU.

Set the device within the range that can be monitored by the monitored

PLC CPU and parameter settings.

Channel No.

storage

17

18

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

18 - 13

Error code

330

331

Error message

Memory card not installed or

MCARD switched OFF

332 Memory media is not formatted.

333

334

337

345

351

Insufficient memory media capacity.

Confirm M-card capacity.

Unable to overwrite. Memory card is write-protected.

Memory media error.

Replace memory media.

File output failed.

Confirm output file path.

BCD/BIN conversion error

Correct data

Recipe file error.

Confirm content of recipe file.

Action

Available memory of the SD card is insufficient.

Confirm the available memory of the SD card.

The available memory can be confirmed by system information screen, which is described in GT Designer3 Version1 Screen Design Manual

(Fundamentals).

The SD card is not installed or in the drive access switch is OFF in drive.

• Install the SD card in the specified drive.

• Turn ON the access switch.

SD card is not formatted or formatted incorrectly.

Format the SD card.

SD card is write-protected.

Cancel the write-protection of SD card.

SD card is faulty.

Replace the SD card.

Either of the following folder or file with the name same as the file to be created exists in the storage destination SD card or USB memory.

• Folder storing data

• Write-protect file

Delete the above folder or file, or change the name of the file to be created.

Any value that cannot be converted to a BCD/BIN value is being displayed/input.

• Change the device data to be displayed to the BCD value.

• Correct the input value to the 4 digits integer.

The contents of the recipe file are not normal.

• Confirm the contents of the recipe files in the SD card or USB memory.

• Reboot the GOT after deleting the recipe file in the SD card or USB memory (format).

352

Recipe file make error.

Reboot GOT after inserting memory card.

Failed to generate recipe file.

Reboot the GOT after installing the SD card or USB memory.

353

354 Recipe file write error

355 Recipe file read error

356

357

Unable to write Recipe file.

Confirm memory card is inserted.

File system error occurred in

PLC.

Confirm file register.

Error in specified PLC drive

Confirm PLC drive.

Failed to write in the recipe file.

• Confirm the write-protection of the SD card or USB memory.

• Confirm the contents of the SD card or USB memory.

• Do not pull out the SD card or USB memory while recipe is operating.

Error occurred while writing in the recipe file.

Do not pull out the SD card or USB memory while recipe is operating.

Error occurred while reading in the recipe file.

• Do not pull out the SD card or USB memory while recipe is operating.

• Confirm the contents (device value) of the recipe file in the SD card or

USB memory.

Error occurred in the specified file register when executing the recipe function by specifying the file register name.

• Execute the recipe function again after confirming the file register name.

• Execute the recipe function again after formatting the PC memory in the specified PLC CPU drive with GX Developer.

When executing the recipe function specifying the file register name, error occurred in PLC CPU drive.

• Execute the recipe function again after confirming the specified PLC

CPU drive.

• Execute the recipe function again after formatting the PC memory in the specified PLC CPU drive with GX Developer.

18 - 14

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

Channel No.

storage

Error code

Error message Action

358

359

360

361

362

PLC file access failure.

Confirm PLC drive.

Processing from another peripheral device.

Execute it after.

0 divisor division error.

Confirm operation expression.

Specified device No. is out of range.

Invalid device value in time action setting

370

Upper and lower limit value error.

Confirm value setting.

380

381

Insufficient USB drive capacity.

Confirm the drive capacity.

USB drive is not installed or in a removable state.

382 USB drive is not formatted.

383

384

402

403

406

Unable to overwrite. USB drive is write-protected.

USB drive error. Replace USB drive.

Communication timeout.

Confirm communication pathway or modules.

SIO status error.

Confirm communication pathway or modules.

Specified station access is out of range.

Confirm station no.

When the recipe function is executed specifying the file register name,

PLC CPU file register could not be accessed.

• Execute the recipe function again after confirming the specified PLC

CPU drive / file register name. (When you specify drive 0, execute the recipe function again after changing to other drives.)

• Confirm whether the SD card or USB memory are write-protected, and execute the recipe function again.

When the recipe function is executed specifying the file register name, other peripherals carry out the process to the file register.

Wait until the processing of other peripherals end, and execute the recipe function again.

Zero division occurred by the data operational expression.

Review the data operational expression so that the divisor should not become 0.

The entered file number is out of range.

Check the entered file number, and enter a valid value (1 to 9999).

When controllers are controlled with the GOT's time action function, the set No. is our of range, or the set device values regarding the operation settings are out of range or invalid.

Set valid values.

The setting of lower/upper limit value is [Upper limit < Lower limit].

Correct the setting so as to be "Upper limit &inequalityLEM Lower limit".

Available memory of the USB memory is insufficient.

Confirm the available memory of the USB memory, and increase the memory if it is low.

If the USB memory is not installed, install it.

If the USB memory is ready to be removed, install it again.

Memory card is not formatted or in a format not conformed by a GOT.

Reformat the USB memory.

USB memory is write-protected.

Cancel the write-protection of USB memory.

USB memory is faulty.

Replace the USB memory.

The time-out error occurred during communicating.

• Confirm the cable omission and status of the PLC.

Channel No. is not displayed in error code or error message in the case an error occurs when using the multi-channel function.

Refer to the following manual to identify the channel No. in error.

• This error may occur when the load of the PLC CPU becomes heavier when accessing other stations. In such a case, transfer the data of the other stations to the host station PLC CPU and monitor them at the host.

• Put COM instruction when the PLC scanning is long.

Either of the overrun error, parity bit error or flaming error was generated when the RS-422 / RS-232 communication was received.

Confirm the cable omission, status of the PLC.and the transmission speed of the computer link.

Channel No. is not displayed in error code or error message in the case an error occurs when using the multi-channel function.

• Station numbers other than master/local station are specified at the

CC-Link connection (via G4).

• A PLC CPU other than QCPU is accessed.

• Confirm the station number of the project data.

Channel No.

storage

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

18 - 15

17

18

Error code

Error message Action

407

410

Accessed other network.

Change network setting.

Cannot perform operation because of PLC run mode.

stop the PLC.

• When monitoring other networks

Reconfigure the [Routing Information Setting] of GT Designer3 or the

[Routing parameters] of GX Developer.

The operation, which could not be performed during RUN of PLC CPU, was performed.

Stop the PLC CPU.

The memory cassette installed in the PLC CPU is EPROM or E

2

PROM, and it is in a protected status.

Confirm the memory cassette installed in PLC CPU.

411

Memory cassette is writeprotected.

Check the memory cassette.

412

Cannot read/write device protected by keyword.

Remove keyword.

The key word is set in PLC CPU.

Cancel the key word.

420 E71 specification is ASCII.

421

422

423

424

Not communicating between

CPU and E71. Confirm CPU error.

Same sta. on GOT & project data. Review communication parameter.

425

A duplicate IP address has been detected. Confirm the setting.

448

E71 is set as read-only.

Clear setting.

Insufficient network table information. Add station no.

PLC cannot handle as requested. Correct devices.

[ASCII code] is selected in [Ethernet operations] of the PLC side setting.

Select [Binary code].

The Ethernet module on the PLC side is set in read-only.

Set the Ethernet module on the PLC side to write-enabled.

PLC CPU error. Communication between PLC CPU and the PLC side

Ethernet module impossible.

Confirm whether there is error in PLC CPU by GX Developer etc.

(Confirm buffer memory)

The station number set in the project data and the station number set in the switching station No. device do not exist in the Ethernet setting of GT

Designer3.

• Add the station number set in the project data to the Ethernet setting of

GT Designer3.

• When using the station No. switching function, check the data of the switching station No. device.

When the station number specified in the switching station No. device is not set in the Ethernet setting, add the station number to the

Ethernet setting.

When the station number does not exist in the system, change the data of the switching station No. device.

(Set the station number so that it becomes the same as the station number of the PLC side Ethernet module set in the parameter setting of GX Developer.)

The station number set in the GOT's utility is the same as the station number set in the Ethernet setting of GT Designer3 or GT Designer2 (the station number of the PLC side Ethernet module) or in the project data.

Check the following contents so that the multiple station numbers should not be the same.

• Check the GOT's station number in the GOT's utility.

• Check the station number set in the project data.

• Check the station number set in the Ethernet setting.

(Set the station number so that it becomes the same as the station number of the PLC side Ethernet module set in the parameter setting of GX Developer.)

• When using the station No. switching function, check the data of the switching station No. device.

The IP address of the GOT is the same as that of the controller.

Change the IP address of the GOT or the controller.

A device outside the range of PLC file registers and the buffer memory was specified.

Correct the monitor device by setting file register of the PLC CPU.

Channel No.

storage

18 - 16

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

Error code

Error message

449

Dedicated device is out of range.

Confirm device range.

450

451

460 Communication unit error

480

Path has changed or timeout occurred in redundant system.

Q redundant system settings and current config. do not match.

Communication channel not set.

Set channel number on Utility.

Action

Set the address for the special function module in the GOT monitor available range. Set the device in the GOT monitor available range.

The path has been switched or timeout occurred in the redundant system.

• Check the PLC CPU to know if the path has been switched.

• Check the cable connection status and the PLC CPU status.

• This error may occur when the load of the PLC CPU becomes heavier when accessing other stations. In such a case, transfer the data of the other stations to the host station PLC CPU and monitor them at the host.

• Perform one of the following operations if the PLC scanning time is long: COM instruction/Extension of END processing/Setting of the number of processing times for general data/Data update batch processing.

Change the Q redundant setting in accordance with the actual Q redundant CPU system.

• Reset the power of the GOT.

• Replace the unit.

Channel (CH.No.1 to 2) to communicate with a controller is not set.

• After setting the Communication Settings on the GT Designer3, download it to the GOT.

• Change the channel assignment in the Communication Setting on the utility.

487

Please turn on the PLC and the

GOT again.

Turn the power of the PLC and GOT on again.

489

500

510 Clock data input out of range

520 Insufficient Flash ROM capacity

521

522

524

525

Inactive channel has been selected at Communication

Settings.

Warning! Built-in battery voltage is low.

Insufficient user memory (RAM) capacity

Unnecessary file deleted to create new file.

Device writing error.

Correct device.

Unable to read/write alarm log files under different projects.

526 File conversion failed.

Inactive channel No. has been set in the project data.

• Check whether any unnecessary channel No. has been set in the project data.

• Check whether channel Nos. set in the project data are set in the

Communication Settings.

The voltage of the GOT built-in battery is decreased.

Replace the GOT built-in battery.

The value that is input as clock data is out of the input enabled range.

In this case, the input value is not accepted.

Confirm the input range of the value to be input as clock data, and input the proper value again.

The capacity for the buffering area is insufficient in the build in flash memory

• Confirm whether there are no mistakes in specified buffering area size.

The capacity for the buffering area is insufficient in the user memory

(RAM)

• Confirm whether there are no mistakes in specified buffering area size.

The old file of different contents has been deleted and a new file has been created.

Note that the old file is deleted and the new file is created if the file of the same name with different contents exists when creating files.

Error occurred while writing in the device.

Correct the device.

Unable to read the alarm log file saved by the different project.

Confirm where to store the alarm log file and alarm log file.

The file specified for the file conversion does not exist.

Check the settings for specifying a file to be converted.

Channel No.

storage

*1

*1

17

18

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

18 - 17

Error code

Error message Action

528

529

530

535 Cannot open image file.

536

540

570 Recipe device points too large.

571

Capacity shortage of user memory (RAM)

581 Abnormal Advanced recipe file

582

583

Cannot generate Advanced recipe file.

Unable to save device value to

Advanced recipe file.

584 Advance recipe file save error

585 Advanced recipe file upload error

586

587

588

Error in SRAM. Failed to write data.

Data error in SRAM.

Check the battery life.

Improper monitor device.

Confirm monitor channel.

Image file error or invalid file format.

Auto repeat error. Confirm system information.

Specified Advanced recipe number does not exist.

Specified record number does not exist.

Cannot save recipe data to read only record.

The error may be caused by a failure in the GOT main unit. Please consult your local Mitsubishi (Electric System) Service center or representative.

Error in SRAM data due to battery voltage low, etc.

Confirm the battery status.

The channel of the specified monitor target does not exist or the channel is not the monitor target.

Confirm the monitor target channel of the screen data.

Confirm whether any file exists in the SD card or USB memory.

• Confirm whether image files in the SD card or USB memory are normal.

• Confirm whether any image file of invalid format is stored.

Error occurred while executing the auto repeat function of the touch switch object.

Confirm the following.

• Confirm that the other system error has not occurred during auto repeat.

• Confirm that any error information is not stored in the system information/GS during auto repeat.

The number of the set points of the recipe device exceeds the specified range.

Put the number of the set points of the recipe device within the specified range.

There is no empty area/space in D drive.

Format the D drive in the memory to secure free area.

Advanced Recipe cannot be executed for advanced recipe file with incorrect contents. Delete the advanced recipe file from the SD card or

USB memory.

Cannot generate advanced recipe file. Confirm the following and execute recipe processing again.

• Confirm whether the SD card or USB memory is installed.

• Confirm whether the SD card access switch of the GOT is ON.

• Confirm the available memory of the SD card or USB memory.

Unable to save device value to advanced recipe file.

• Confirm the write-protection of the SD card or USB memory.

• Confirm whether the attribute of saving file is for reading only.

An error has occurred during the advanced recipe file writing.

Do not pull out the SD card or USB memory while the Advanced Recipe is operating.

An error has occurred during the advanced recipe file reading.

Do not pull out the SD card or USB memory while the Advanced Recipe is operating.

The advanced recipe of non-existing number is about to be executed.

Execute advanced recipe of existing number.

The advanced record of non-existing number is about to be executed.

Execute record of existing number.

Saving recipe is about to be executed to the record of which recipe device value cannot be edited.

Make the recipe device value of the record editable with Advanced

Recipe Setting of GT Designer3 or specify the record of which recipe device value can be edited.

Channel No.

storage

18 - 18

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

Error code

Error message Action

589

Recipe device save error. Recipe file does not exist.

590

591

595 Logging file error.

596

Logging setting does not exist or setting value error.

605 USB device I/F error

611

612

613 Error in writing logfile

614 Error in reading logfile

615

Recipe device upload error.

Recipe device value does not exist.

Advanced Recipe error. Check recipe data.

Improper job files.

Confirm job setting.

Cannot access Logging Files

Check the memory card

Cannot connect to MES Server.

Check the Server.

616

Cannot connect to SNTP Server.

Check the Server.

640

An error occurred in a FTP client process.

800 Abnormal module status

801 Abnormal baton passing status

802

Abnormal cyclic transmission status

803 Transient error

Saving recipe is about to be executed to the advanced recipe setting that is set for not using file.

Specify the advanced recipe setting that uses file.

Loading recipe is about to be executed to the record of which recipe device value is not set.

Specify the record of which recipe device value is set.

The advanced recipe setting is not correct.

Confirm the advanced recipe setting of the project data and download it to the GOT again.

Logging file error.

When collecting data again, delete logging files and management files.

The logging setting specified in the historical trend graph setting does not exist.

Review the historical trend graph setting and specify a logging setting that exists.

The error may be caused by a failure in the GOT. Please consult your local Mitsubishi (Electric System) Service center or representative.

The contents for job files are unmatched with the settings for job files.

Check if there are mistakes in the settings on the setting screen.

• Insert a SD card or USB memory.

• Turn on the SD card access switch.

• If the SD card or USB memory have unnecessary files, delete the files.

• Insert a SD card or USB memory.

• Turn on the SD card access switch.

• Check if the SD card or USB memory is writable.

• Insert a SD card or USB memory.

• Turn on the SD card access switch.

• Check if the SD card or USB memory is readable.

The server does not work normally or the connection path to the server is made up incorrectly.

• Check the operating conditions of the server.

• Check the network to the server.

The settings for the SNTP server are wrong or the network to the SNTP server is made up incorrectly.

• Check the operating conditions of the STNP server.

• Check the network to the SNTP server.

Reconfigure the GOT (FTP client) setting.

Check the operating status and network line of the FTP server.

For the error details, check the GOT special register GS989 (FTP communication error notification).

Refer to explanations of SB0020 on the applicable network manual.

Refer to explanations of SB0047 on the applicable network manual.

Refer to explanations of SB0049 on the applicable network manual.

850 CC-Link switch setting error

Refer to explanations of SB00EE on the applicable network manual.

• Check if the switch settings have no error.

• Check error codes stored in SW006A.

• Refer to explanations of SB006A on the applicable network manual

Channel No.

storage

17

18

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

18 - 19

Error code

Error message Action

851

Abnormal cyclic transmission status

852 Abnormal host line status

• Check if terminating resistors are connected.

• Check error codes for the PLC CPU.

• Check the parameter for the PLC CPU on the master station.

• Check the error status of the master station.

• Refer to explanations of SB006E on the applicable network manual.

• Check if the cable is unplugged or not.

• Refer to explanations of SB0090 on the applicable network manual.

853 Transient error

*1

• Check the transient error occurrence status for each station stored in

SW0094 to SW0097.

• Refer to explanations of SB0094.

When an error occurs, "FF

H

" is stored to the channel No.

Channel No.

storage

18 - 20

18. TROUBLESHOOTING

18.2 Error Message and System Alarm

APPENDICES

Appendix.1 External Dimensions

„

External dimensions of GT14

22

(0.87")

164(6.46")

120(4.73")

23(0.91")

#4-40UNC

(Inch screw type)

M2.6

(Metric screw type)

22

(0.87")

120(4.73")

152(5.99")

„

External dimensions of stand

For angle of 75

153(6.03")

220(8.67")

Panel thickness:

2mm 4mm(0.08" 0.16") or less

Unit: mm (inch)

260(10.24")

Unit: mm (inch)

APPENDICES

Appendix.1 External Dimensions

App - 1

17

18

„

External dimensions of serial multi-drop connection unit

Protective cover is installed Protective cover is removed

57(2.25")

65(2.56")

2- 4.5

„

External dimensions of connector conversion adapter

Unit : mm (inch)

36(1.42")

22

(0.87")

Unit : mm (inch)

App - 2

APPENDICES

Appendix.1 External Dimensions

„

External dimensions of RS-232/485 signal conversion adapter

36(1.42") 17

(0.67")

Unit : mm (inch)

17

18

APPENDICES

Appendix.1 External Dimensions

App - 3

„

External dimensions of communication cable

GT01-C30R4-25P

16

(0.63")

50(1.97") 30000(1181.1")

7

(0.28")

53(2.09")

GT01-C

16

(0.63")

R4-25P

50(1.97")

M2.6

M2.6

L

7

(0.28")

M2.6

Value of

100

200

300

GT01-C

16

(0.63")

R4-8P

50(1.97") L

6

16

(0.63")

53(2.09")

M2.6

Length L mm (inch)

10000

20000

30000

25×33

(0.99") (1.3")

40(1.58")

Unit: mm (inch)

13

(0.52")

16

(0.63")

M2.6

Value of

10

30

100

200

300

Length L mm (inch)

1000

3000

10000

20000

30000

App - 4

APPENDICES

Appendix.1 External Dimensions

GT01-C30R2-25P

16

(0.63")

50(1.97") 30000(1181.1") 53(2.09")

GT01-C30R2-9S

16

(0.63")

50(1.97")

#4-40UNC

M2.6

30000(1181.1")

φ6

#4-40UNC

6

#4-40UNC

GT01-C30R2-6P

16

(0.63")

50(1.97")

50(1.97")

30000(1181.1")

7

(0.28")

20×28

(0.79") (1.11")

40(1.58")

#4-40UNC

16

(0.63")

16

(0.63")

13

(0.52")

17

18

APPENDICES

Appendix.1 External Dimensions

App - 5

App - 6

APPENDICES

Appendix.1 External Dimensions

Appendix.2 Usage Condition of Utility Function

17

The function which can be used differs according to the GOT type.

Moreover, there are the function which can be set with drawing software and the function which cannot be set.

Communication setting

GOT setup

Item

Communication setting

Ethernet setting

Display

Operation

Transparent mode

Backup/restoration

Behavior of duplicate IPs

OS information

Alarm information

Project information

Hard copy information

Functions overview

: Applicable : Not applicable -: Not required

GT14 GT11

Refere nce

Assigning channel numbers and communication drivers to communication interfaces

Setting communication parameters

Setting or deleting sequence program protection key words, canceling sequence program protection status (When connecting to FX series CPU)

Displaying the contents of Ethernet setting, changing the host

Switching message languages

Setting the startup screen display time and screen saving time

Setting the backlight to ON or OFF during screen saving

Setting the battery alarm display to ON or OFF

Adjusting brightness and contrast

Inverting colors

Setting the buzzer volume and window move buzzer

Setting the key sensitivity and key reaction speed

Changing security levels

Setting the utility call keys

Adjusting the touch panel

Setting the USB mouse and keyboard

Setting the channel No. to be used for the communication for the FA transparent function

Setting the storage locations for backup data and backup settings, and setting the maximum number of backup data

Trigger backup settings

Setting the GOT operation when a device with the same IP address as that of the GOT is added to the network afterwards

Installing or uploading OS, displaying OS property, checking OS data

Deleting or copying alarm log files

Converting alarm log files in G1A format CSV or TXT format

Downloading, uploading, deleting or copying project files, displaying project file property, checking project file data

Deleting or copying hard copy files, changing hard copy file names

Program/ data control

Advanced Recipe information

Logging information

Memory card format

Memory information

Converting advanced recipe files in G1P format CSV or TXT format

Converting advanced recipe files in CSV or TXT format G1P format

Deleting, copying or moving advanced recipe files, creating a new advanced recipe file

Deleting or moving advanced recipe folders, changing advanced recipe folder names, creating a new advanced recipe folder

Writing, reading or matching record data and deleting device values with the advanced recipe record list

Converting logging files in G1L format CSV or TXT format

Deleting, copying or moving logging files, changing logging file names

Deleting logging folders or creating a new logging folder

Formatting a SD card or USB memory, internal SRAM

Displaying the available memory of the GOT

USB device status display

SRAM control

Displaying the status of USB device

Back up, restoring and initializing of the SRAM user area

GOT data package acquisition Copying the OS, special data, and project data to a CF card or USB memory

18

APPENDICES

Appendix.2 Usage Condition of Utility Function

App - 7

Time setting & display

Item

Debug

Debug & self check

Self check

System alarm display

GOT start time

Clean

Functions overview

: Applicable : Not applicable -: Not required

GT14 GT11

Refere nce

Selecting a base clock

Displaying and setting the clock current time

Displaying the battery status

System monitor

FX list editor

A list editor

Backup/restoration

Memory check

Drawing check

Font check

Touch panel check

I/O check

Displaying error code and error message

Displaying GOT start date and time, current time, accumulated operating hours

Displaying the screen for cleaning the display

App - 8

APPENDICES

Appendix.2 Usage Condition of Utility Function

Appendix.3 Transportation Precautions

17

When transporting lithium batteries, make sure to treat them based on the transport regulations.

Appendix.3.1 Relevant models

The battery for the GOT1000 series is classified as shown in the table below.

Product name

Battery for GOT1000 series

Model name

GT11-50BAT

Description

Lithium battery

Handled as

Non-dangerous goods

Appendix.3.2 Transportation guidelines

Products are packed properly in compliance with the transportation regulations prior to shipment. When repacking any of the unpacked products to transport it to another location, make sure to observe the IATA Dangerous Goods Regulations,

IMDG Code and other local transportation regulations.

For details, please consult your transportation company.

18

APPENDICES

Appendix.3 Transportation Precautions

App - 9

App - 10

APPENDICES

Appendix.3 Transportation Precautions

INDEX

[A]

A list editor........................................................... 14-1

ABBREVIATIONS AND GENERIC TERMS ........ A-15

Adjusting the touch panel position..................... 11-13

Advanced recipe information ............................. 13-33

Alarm information .............................................. 13-11

[B]

Backlight Shutoff Detection ................................. 17-7

Backup/restoration............................................... 14-2

Backup/Restoration Setting ............................... 11-18

Battery ........................................................... 8-4,17-4

Battery alarm display ................................... 11-1,11-4

Behavior of Duplicate IPs .................................. 11-21

BootOS ................................................................ 16-1

Brightness, contrast..................................... 11-1,11-5

Buzzer volume setting ................................. 11-6,11-8

[C]

Clean ........................................................... 15-1,17-3

Cleaning of display section.................................. 15-1

Communication Detail Setting ............................. 10-8

Communication setting ........................................ 10-1

Connector Conversion Adapter ........................... 8-11

CoreOS.............................................................. 16-11

[D]

Daily Inspection ................................................... 17-2

Data type and storage location............................ 13-1

Debug .................................................................. 14-1

Display Setting..................................................... 11-1

Drawing check ..................................................... 14-6

[E]

Error Message ......................................... 18-11,18-13

Ethernet Setting................................................. 10-15

External Dimensions.......................................... App-1

[F]

FILE DISPLAY AND COPY ................................. 13-1

Font check ......................................................... 14-10

FX list editor......................................................... 14-1

[G]

GOT data package acquisition .......................... 13-73

GOT internal battery voltage status..................... 12-3

GOT Restoration Sheet ....................................... 18-1

GOT start time ................................................... 14-19

[H]

Hard copy information ....................................... 13-27

[I]

I/O check............................................................ 14-14

INSTALLATION ..................................................... 6-1

[K]

Key sensitivity setting .................................. 11-6,11-8

[L]

Language..................................................... 11-1,11-3

Logging information ........................................... 13-53

[M]

MAINTENANCE AND INSPECTION ................... 17-1

Memory card format........................................... 13-63

Memory check ..................................................... 14-3

Memory information ........................................... 13-65

[O]

Opening screen time.................................... 11-1,11-4

OS information..................................................... 13-5

OS version confirmation ...................................... 13-3

[P]

Panel Cutting Dimension ....................................... 6-2

Panel-Mounted USB Port Extension.................... 8-14

PARTS NAME ....................................................... 4-1

Back Panel ......................................................... 4-2

Front Panel......................................................... 4-1

Rear Face .......................................................... 4-3

Periodic Inspection .............................................. 17-2

Project Information............................................. 13-17

Protective Cover for Oil.......................................... 8-7

Protective Sheet .................................................... 8-6

[R]

RS-232/485 signal conversion adapter................ 8-16

[S]

Screen save backlight.................................. 11-1,11-4

Screen save time ......................................... 11-1,11-4

SD Card ................................................................. 8-1

Security level change........................................... 11-9

Self Check ........................................................... 14-3

Serial Multi-Drop Connection Unit ....................... 8-12

SPECIFICATIONS................................................. 3-1

General Specifications ....................................... 3-1

Performance Specifications ............................... 3-2

Power Supply Specifications.............................. 3-3

SRAM control..................................................... 13-68

Stand ................................................................... 8-10

Standard monitor OS ........................................... 16-1

System Alarm .......................................... 18-11,18-13

System Alarm Display........................................ 14-17

SYSTEM CONFIGURATION................................. 2-1

Overall Configuration ......................................... 2-1

Index-1

System Equipment ............................................. 2-1

System monitor.................................................... 14-1

[T]

Time Setting and Display..................................... 12-1

Clock display .................................................... 12-3

Clock setting..................................................... 12-2

Touch panel check ............................................ 14-12

Transparent Mode Setting ................................. 11-17

Transportation Precautions ............................... App-9

TROUBLESHOOTING ........................................ 18-1

[U]

USB device status display ................................. 13-66

USB Environmental Protection Cover ................... 8-9

USB memory ......................................................... 8-3

USB mouse/keyboard setting ............................ 11-15

Utility Call Key Setting ....................................... 11-11

UTILITY FUNCTION....................................9-1,App-7

Display ............................................................... 9-4

Function List....................................................... 9-2

[W]

Window move buzzer volume setting .......... 11-6,11-8

WIRING ................................................................. 7-1

Power Supply Wiring.......................................... 7-2

Wiring inside....................................................... 7-5

Wiring outside .................................................... 7-5

Index-2

REVISIONS

Print Date

Oct., 2011

Jan., 2012

Jan., 2012

* Manual Number

JY997D44801

JY997D44801

JY997D44801

* The manual number is given on the bottom left of the back cover.

Sub

Number

A

B

C

Revision

First edition

Compatible with GT Works3 Version1.40S

• GT14-RS2T4-9P type RS-232/485 signal conversion adaptor compatible

Compatible with GT Works3 Version1.40S

• UL, cUL Standards supported

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric

Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.

© 2011 MITSUBISHI ELECTRIC CORPORATION

REVISIONS - 1

REVISIONS - 2

WARRANTY

Please confirm the following product warranty details before using this product.

1. Gratis Warranty Term and Gratis Warranty Range

If any faults or defects (hereinafter "Failure") found to be the responsibility of Mitsubishi occurs during use of the product within the gratis warranty term, the product shall be repaired at no cost via the sales representative or Mitsubishi Service Company.

However, if repairs are required onsite at domestic or overseas location, expenses to send an engineer will be solely at the customer's discretion. Mitsubishi shall not be held responsible for any re-commissioning, maintenance, or testing on-site that involves replacement of the failed module.

[Gratis Warranty Term]

The gratis warranty term of the product shall be for thirty-six (36) months after the date of purchase or delivery to a designated place.

Note that after manufacture and shipment from Mitsubishi, the maximum distribution period shall be six (6) months, and the longest gratis warranty term after manufacturing shall be forty-two (42) months. The gratis warranty term of repair parts shall not exceed the gratis warranty term before repairs.

[Gratis Warranty Range]

(1) The customer shall be responsible for the primary failure diagnosis unless otherwise specified.

If requested by the customer, Mitsubishi Electric Corporation or its representative firm may carry out the primary failure diagnosis at the customer’s expense.

The primary failure diagnosis will, however, be free of charge should the cause of failure be attributable to Mitsubishi Electric

Corporation.

(2) The range shall be limited to normal use within the usage state, usage methods and usage environment, etc., which follow the conditions and precautions, etc., given in the instruction manual, user's manual and caution labels on the product.

(3) Even within the gratis warranty term, repairs shall be charged for in the following cases.

1. Failure occurring from inappropriate storage or handling, carelessness or negligence by the user. Failure caused by the user's hardware or software design.

2. Failure caused by unapproved modifications, etc., to the product by the user.

3. When the Mitsubishi product is assembled into a user's device, Failure that could have been avoided if functions or structures, judged as necessary in the legal safety measures the user's device is subject to or as necessary by industry standards, had been provided.

4. Failure that could have been avoided if consumable parts designated in the instruction manual had been correctly serviced or replaced.

5. Replacing consumable parts such as the battery, backlight and fuses.

6. Failure caused by external irresistible forces such as fires or abnormal voltages, and Failure caused by force majeure such as earthquakes, lightning, wind and water damage.

7. Failure caused by reasons unpredictable by scientific technology standards at time of shipment from Mitsubishi.

8. Any other failure found not to be the responsibility of Mitsubishi or that admitted not to be so by the user.

2. Onerous repair term after discontinuation of production

(1) Mitsubishi shall accept onerous product repairs for seven (7) years after production of the product is discontinued.

Discontinuation of production shall be notified with Mitsubishi Technical Bulletins, etc.

(2) Product supply (including repair parts) is not available after production is discontinued.

3. Overseas service

Overseas, repairs shall be accepted by Mitsubishi's local overseas FA Center. Note that the repair conditions at each FA Center may differ.

4. Exclusion of loss in opportunity and secondary loss from warranty liability

Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation to damages caused by any cause found not to be the responsibility of Mitsubishi, loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi products, special damages and secondary damages whether foreseeable or not, compensation for accidents, and compensation for damages to products other than Mitsubishi products, replacement by the user, maintenance of on-site equipment, start-up test run and other tasks.

5. Changes in product specifications

The specifications given in the catalogs, manuals or technical documents are subject to change without prior notice.

6. Product application

(1) In using the Mitsubishi graphic operation terminal, the usage conditions shall be that the application will not lead to a major accident even if any problem or fault should occur in the graphic operation terminal device, and that backup and fail-safe functions are systematically provided outside of the device for any problem or fault.

(2) The Mitsubishi graphic operation terminal has been designed and manufactured for applications in general industries, etc.

Thus, applications in which the public could be affected such as in nuclear power plants and other power plants operated by respective power companies, and applications in which a special quality assurance system is required, such as for Railway companies or Public service purposes shall be excluded from the graphic operation terminal applications.

In addition, applications in which human life or property that could be greatly affected, such as in aircraft, medical applications, incineration and fuel devices, manned transportation equipment for recreation and amusement, and safety devices, shall also be excluded from the graphic operation terminal range of applications.

However, in certain cases, some applications may be possible, providing the user consults the local Mitsubishi representative outlining the special requirements of the project, and providing that all parties concerned agree to the special circumstances, solely at our discretion.

In some of three cases, however, Mitsubishi Electric Corporation may consider the possibility of an application, provided that the customer notifies Mitsubishi Electric Corporation of the intention, the application is clearly defined and any special quality is not required.

GOT is a registered trademark of Mitsubishi Electric Corporation.

Microsoft, Windows, Windows NT, Windows Vista, Windows 7 are registered trademarks or trade marks of Microsoft

Corporation in the United States and other countries.

Adobe and Adobe Reader are registered trademarks of Adobe Systems Incorporated.

Pentium and Celeron are a registered trademarks of Intel Corporation in the United States and other countries.

Ethernet is a trademark of Xerox Co., Ltd. in the United States.

MODBUS is a trademark of Schneider Electric SA.

Other company and product names herein are either trademarks or registered trademarks of their respective owners.