Acer Veriton C630 User manual

Acer Veriton C630 User manual
Veriton Series
User Guide
VT002
Copyright © 2012.
All Rights Reserved.
Veriton Series User Guide
Original Issue: 04/2012
Veriton Series Desktop Computer
Model number: __________________________________
Serial number: ___________________________________
Purchase date: ___________________________________
Place of purchase: ________________________________
Visit http://registration.acer.com and discover the benefits of being an Acer customer.
iii
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future reference. Follow
all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
Warnings
•
•
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable operation of
the product and to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This product should never
be placed near or over a radiator or heat register, or in a built-in installation
unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind onto or into the product.
To avoid damage of internal components and to prevent battery leakage, do
not place the product on a vibrating surface.
Using electrical power
•
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult your
dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this product
where people will walk on the cord.
If an extension cord is used with this product, make sure that the total ampere
rating of the equipment plugged into the extension cord does not exceed the
extension cord ampere rating. Also, make sure that the total rating of all
products plugged into the wall outlet does not exceed the fuse rating.
Do not overload a power outlet, strip or receptacle by plugging in too many
devices. The overall system load must not exceed 80% of the branch circuit
rating. If power strips are used, the load should not exceed 80% of the power
strip's input rating.
iv
•
This product's AC adapter is equipped with a three-wire grounded plug. The
plug only fits in a grounded power outlet. Make sure the power outlet is
properly grounded before inserting the AC adapter plug. Do not insert the plug
into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power
outlet that is not properly grounded may result in electric shock
and/or injury.
Note: The grounding pin also provides good protection from
unexpected noise produced by other nearby electrical devices that
may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to
replace the power cord set, make sure that the new power cord meets the
following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
The power cord or plug is damaged, cut or frayed.
•
•
•
•
•
Liquid was spilled into the product.
The product was exposed to rain or water.
The product has been dropped or the case has been damaged.
The product exhibits a distinct change in performance, indicating a need for
service.
The product does not operate normally after following the operating
instructions.
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
v
Telephone line safety
•
•
Disconnect all telephone lines from the equipment when not in use and/or
before servicing.
To avoid the remote risk of electric shock from lightning, do not connect the
telephone line to this equipment during lightning or thunderstorms.
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global environment,
please recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
http://www.acer-group.com/public/Sustainability/sustainability04.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org.
ENERGY STAR
ENERGY STAR qualified products save you money by reducing
energy cost and protecting the environment without sacrificing
features or performance. Acer is proud to offer our customers
products with the ENERGY STAR mark.
What is ENERGY STAR?
Products that are ENERGY STAR qualified use less energy and
prevent greenhouse gas emissions by meeting strict energy efficiency guidelines
set by the U.S. Environmental Protection Agency. Acer is committed to offer
products and services worldwide that help customers save money, conserve energy
and improve the quality of our environment. The more energy we can save through
higher energy efficiency, the more we reduce greenhouse gases and the risks of
climate change. More information refers to www.energystar.gov.
vi
Note: The statement above is applicable only to Acer system with an
ENERGY STAR sticker.
Acer ENERGY STAR qualified products:
•
•
•
•
Produce less heat and reduce cooling loads, and warmer climates.
Automatically go into "display sleep" and "computer sleep" mode after
10 and 30 minute of inactivity respectively.
Wake the computer from sleep mode by pushing keyboard or moving
mouse.
Computers will save more than 80% energy at "sleep" mode.
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks
Tips and information for comfortable use
Computer users may complain of eyestrain and headaches after prolonged use.
Users are also at risk of physical injury after long hours of working in front of a
computer. Long work periods, bad posture, poor work habits, stress, inadequate
working conditions, personal health and other factors greatly increase the risk of
physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome, tendonitis,
tenosynovitis or other musculoskeletal disorders. The following symptoms may
appear in the hands, wrists, arms, shoulders, neck or back:
•
•
•
•
•
Numbness, or a burning or tingling sensation.
Aching, soreness or tenderness.
Pain, swelling or throbbing.
Stiffness or tightness.
Coldness or weakness.
If you have these symptoms, or any other recurring or persistent discomfort and/or
pain related to computer use, consult a physician immediately and inform your
company's health and safety department.
The following section provides tips for more comfortable computer use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor, using a
footrest, or raising your sitting height to achieve maximum comfort. Observe the
following tips:
•
•
•
•
•
•
Refrain from staying too long in one fixed posture.
Avoid slouching forward and/or leaning backward.
Stand up and walk around regularly to remove the strain on your leg muscles.
Take short rests to relax your neck and shoulders.
Avoid tensing your muscles or shrugging your shoulders.
Install the external display, keyboard and mouse properly and within
comfortable reach.
vii
•
If you view your monitor more than your documents, place the display at the
center of your desk to minimize neck strain.
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive
room lighting, poorly focused screens, very small typefaces and low-contrast
displays could stress your eyes. The following sections provide suggestions on how
to reduce eyestrain.
Eyes
•
•
•
Rest your eyes frequently.
Give your eyes regular breaks by looking away from the monitor and focusing
on a distant point.
Blink frequently to keep your eyes from drying out.
Display
Keep your display clean.
Keep your head at a higher level than the top edge of the display so your eyes
point downward when looking at the middle of the display.
•
Adjust the display brightness and/or contrast to a comfortable level for
enhanced text readability and graphics clarity.
•
Eliminate glare and reflections by:
•
•
•
•
•
Placing your display in such a way that the side faces the window or any
light source.
•
Minimizing room light by using drapes, shades or blinds.
•
Using a task light.
•
Changing the display's viewing angle.
•
Using a glare-reduction filter.
•
Using a display visor, such as a piece of cardboard extended from the
display's top front edge.
Avoid adjusting your display to an awkward viewing angle.
Avoid looking at bright light sources, such as open windows, for extended
periods of time.
Developing good work habits
Develop the following work habits to make your computer use more relaxing and
productive:
•
Take short breaks regularly and often.
•
Perform some stretching exercises.
•
Breathe fresh air as often as possible.
•
Exercise regularly and maintain a healthy body.
Warning! We do not recommend using the computer on a couch
or bed. If this is unavoidable, work for only short periods, take
breaks regularly, and do some stretching exercises.
viii
Safety instructions
Disposal instructions
Tips and information for comfortable use
iii
iii
v
vi
1 System tour
1
Front panel
Rear panel
Optical drive
2
2
4
Taking care of your optical discs
4
2 Setting up your computer
5
Arranging a comfortable work area
6
Positioning your monitor
Positioning your keyboard
Positioning your mouse
Connecting peripherals
Connecting your mouse and keyboard
USB interface
PS/2 interface
Connecting a monitor
Connecting the power cable
6
6
7
7
7
7
7
7
8
Turning on your computer
Turning off your computer
8
8
3 Upgrading your computer
9
Installation precautions
ESD precautions
Preinstallation instructions
Post-installation instructions
Opening your computer
To remove the computer cover
To replace the computer cover
Upgrading your computer
To remove a memory DIMM
To install a memory DIMM
To reconfigure your computer
Replacing the hard disk
Installing an expansion card
10
10
10
10
11
11
11
11
12
13
13
13
14
Contents
Information for your safety and comfort
4 Frequently asked questions
15
Frequently asked questions
16
5 Regulations and safety notices
19
FCC notice
Modem notices
Laser compliance statement
Digital audio output statement
Radio device regulatory notice
Canada — Low-power license-exempt radio
communication devices (RSS-210)
Federal Communications Commission
Remark: All images are for reference purposes only.
Actual configuration may vary.
20
21
23
23
23
24
27
1 System tour
English
2
1 System tour
Front panel
The front panel of your computer has the following:
Icon
Description
Microphone-in jack (front)
Headphone jack
USB ports
USB 3.0
USB 3.0 ports (selected models only)
Recovery button
Network / hard disk drive indicators
Power button
Rear panel
The rear panel of your computer has the following:
Icon
Description
PS/2 mouse port
PS/2 keyboard port
Serial port
VGA port
USB ports
3
Description
USB 3.0
USB 3.0 ports (selected models only)
English
Icon
Network port
Kensington lock slot
DP
Display port (selected models only)
SPDIF
SPDIF port (selected models only)
HDMI port (selected models only)
DC-in jack (selected models only)
DVI port (for selected models only)
The table below indicates the functions of the audio jacks on the rear panel:
Color/use
Headphone
Stereo
Blue
Green
Pink
Quadraphonic
5.1 CH
Rear
Rear
Headphone
Front
Front
Front
Mic-in
Mic-in
Mic-in
Center/
woofer
English
4
1 System tour
Optical drive
Your computer may come with a CD-ROM, DVD-ROM, DVD/CD-RW Combo, DVDDual or DVD-Super multi drive. This drive is located at the front of your computer. A
CD-ROM allows you to play different types of compact discs (CD). A DVD drive can
read CDs, CD-I discs, video-CDs and digital video discs (DVD). CD-RW, DVD-Dual
and DVD-Super multi drives can record (burn) recordadable and rewritable discs.
Caution: Optical discs are fragile and should be handled with care.
To insert an optical disc into your computer’s optical drive:
1
Push the eject button on the front panel.
2
When the tray slides open, place the disc on the tray, maling sure that the label
side faces up.
3
Push the tray gently to close it.
Taking care of your optical discs
Optical discs must be kept free of fingerprints, dirt and scratches. Any dirt or
damage can render data on the disc unreadable or damage the reading lens in the
drive.
•
Keeps discs in their cases when not in use.
•
Hold discs by their edges to avoid getting fingerprints or scratches on the data
surface.
•
When cleaning discs, use a soft, dust-free cloth and wipe the disc in a straight
line from the center to the edge. Do not wipe in a circular motion.
•
Clean your optical drive periodically. Cleaning kits can be purchased from any
computer or electronics shop.
Note: Please refer to the cleaning kit instructions.
2 Setting up your
computer
English
6
2 Setting up your computer
Arranging a comfortable work area
Take note of the following when selecting a location for your computer:
•
Do not put your computer near any equipment that might cause
electromagnetic or radio frequency interference, such as radio transmitters,
televisions, copy machines or heating and air-conditioning equipment.
•
Avoid dusty areas and extremes of temperature and humidity.
•
You may place your computer beside your desk or under your table, as long as
it does not block the space you need for working and moving.
•
To place your PC in a vertical position (for selected models) :
•
Rotate the plastic stabilizers on the side of your computer.
•
Ensure the plastic stabilizers are extended completely.
CAUTION: Please use the stabilizers when placing your PC in the
upright position.
Positioning your monitor
Place your monitor at a comfortable viewing distance, usually 50 to 60 cm away
from you. Adjust the display in such a way that the top of the screen is at or slightly
below eye level.
Positioning your keyboard
The location of the keyboard is a very important factor for your posture. Placing it
too far away will make your body lean forward, forcing you to sit in an unnatural
position. Placing it too high will add tension to your shoulder muscles.
•
The keyboard should be placed just above your lap. Adjust the keyboard
height by flipping the folding stands located under the keyboard.
•
Keep your lower arms parallel to the floor as you type. Your upper arms and
shoulders should be relaxed. Then try typing with a light touch. If you feel any
shoulder or neck strain, stop for a while and check your posture.
•
Position your keyboard in front of your monitor. Putting your keyboard beside
your monitor will make you turn your head while you type which could add
tension to your neck muscles.
7
•
The mouse should be placed on the same surface as your keyboard so that
you can reach it with ease.
•
Adjust its position to allow enough space for movement without making you
stretch or lean over.
•
Use your arm to move the mouse. Do not rest your wrist on the table when
moving the mouse.
Connecting peripherals
Setting up your computer is easy. For the most part, you only have four things to
connect: the mouse, keyboard, monitor and power cable.
Note: The peripherals shown in the connections below are for your
reference only. Actual device models may vary in select countries.
Connecting your mouse and keyboard
USB interface
Plug your USB mouse or keyboard cable into any of the USB ports
the front and rear panels of your computer.
located on
PS/2 interface
Plug the PS/2 keyboard cable into the PS/2 keyboard (purple) port on the rear panel
of your computer. Plug the PS/2 mouse cable into the PS/2 mouse (green) port on
the rear panel of your computer.
Connecting a monitor
To connect a monitor, simply plug the monitor cable into the video port on the rear
panel of your computer .
Note: When a VGA card is added to the PCI Express slot, the monitor
should be connected to the add-on card and the onboard VGA will be
disabled.
Note: Refer to the monitor manual for additional instructions
and information.
English
Positioning your mouse
English
8
2 Setting up your computer
Connecting the power cable
Caution: Before you proceed, check the voltage range in your area.
Make sure that it matches your computer's voltage setting. If they
don't match, change your computer's voltage setting according to
your area's voltage range.
Set the voltage selector switch to the voltage range applicable to your area. Plug
the power cable into the power cable socket located on the rear panel of your
computer. Then plug the other end of the power cable into a power outlet.
Turning on your computer
After connecting the necessary peripherals and plugging in the power cable, you
are now ready to turn the computer on and get to work.
To turn on your computer:
1
Turn on all peripherals connected to your computer, such as the monitor,
printer, speakers, etc.
2
On the front panel of your computer, press the power button.
Important: Make sure that the power cable is properly plugged into
an electrical outlet. If you are using a power strip or an AVR (AutoVoltage Regulator), make sure that it is plugged in and turned on.
Turning off your computer
If you cannot shut down your computer normally, press and hold the power button
for at least four seconds. Quickly pressing the button may put the computer in
suspend mode only.
3 Upgrading
your
computer
English
10
3 Upgrading your computer
Installation precautions
Before you install any computer component, we recommend that you read the
following sections. These sections contain important ESD precautions along with
preinstallation and post-installation instructions.
ESD precautions
Electrostatic discharge (ESD) can damage your processor, disk drives, expansion
boards, and other components. Always observe the following precautions before
you install a computer component:
1
Do not remove a component from its protective packaging until you are ready
to install it.
2
Wear a wrist grounding strap and attach it to a metal part of the computer
before handling components. If a wrist strap is not available, maintain contact
with the computer throughout any procedure requiring ESD protection.
Preinstallation instructions
Always observe the following before you install any component:
1
Turn off your computer and all the peripherals connected to it before opening
it. Then unplug all cables from the power outlets.
2
Open your computer according to the instructions on page 11.
3
Follow the ESD precautions described above before handling a computer
component.
4
Remove any expansion boards or peripherals that block access to the DIMM
sockets or component connectors.
5
See the following sections for specific instructions on the component you wish
to install.
Warning! Not turning off the computer properly before you start
installing the components may cause serious damage. Do not
attempt the procedures described in the following sections
unless you are a qualified service technician.
Post-installation instructions
Observe the following after installing a computer component:
1
See to it that the components are installed according to the step-by-step
instructions in their respective sections.
11
Replace any expansion boards or peripherals that you removed earlier.
3
Replace the side panels.
4
Connect the necessary cables and turn on your computer.
Opening your computer
Caution: Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read the
"Preinstallation instructions" on page 10.
You need to open your computer before you can install additional components. See
the following section for instructions.
To remove the computer cover
1
Turn off your computer and unplug all cables.
2
Place your computer on a flat, steady surface. If your computer is in the
vertical position, rotate the plastic stabilizers and lay your computer on its
side.
3
Turn the screws counterclockwise to release the cover.
4
Hold the sides of the cover with both hands.
5
Slide it back about an inch and then gently lift it upward to detach it.
To replace the computer cover
1
Align the cover's hinges to the housing frame; then gently push it in to slide it
back into place.
2
Secure the cover with the screws.
Upgrading your computer
Certain components of your computer are upgradeable, such as the memory, the
hard disk, the CPU and the expansion cards. You need to observe the "Installation
precautions" on page 10 when installing or removing a computer component.
However, for safety purposes, we do not recommend that you perform these
upgrades yourself. If you want to replace or upgrade any of these components,
contact your dealer or a qualified service technician for assistance.
English
2
English
12
3 Upgrading your computer
To remove a memory DIMM
Note: The memory DIMM has only one notch located toward the
center of the module.
1
Remove the side panel.
2
Locate the memory DIMM socket on the mainboard.
3
Press the holding clips on both sides of the memory DIMM socket outward to
release the memory DIMM (a). Gently pull the memory DIMM out of the socket
(b).
13
1
Locate the memory DIMM socket on the mainboard.
2
Align the memory DIMM with the socket (a). Press the memory DIMM into the
socket until the clips lock onto the memory DIMM (b).
Note: The memory DIMM sockets are slotted to ensure proper
installation. If you insert a memory DIMM but it does not fit easily into
the socket, turn the memory DIMM around and try to insert it again.
To reconfigure your computer
Your computer automatically detects the amount of memory installed. Run the
BIOS utility to view the new value for total system memory and make a note of it.
Replacing the hard disk
Follow these steps to replace your computer's hard disk:
1
Remove the computer cover.
2
Detach all cables connected to the hard disk and pull the hard disk out.
3
Remove the drive rails that hold the hard disk to the disk frame and detach the
hard disk. Set the drive rails aside.
4
Insert the new hard disk into the frame and secure it with drive rails.
5
Reattach all cables to the new hard disk.
English
To install a memory DIMM
English
14
3 Upgrading your computer
Note: Make sure that the other ends of the disk cables are securely
connected to their corresponding connectors on the mainboard.
6
Reinstall the metal bracket frame to the housing.
7
Replace the computer cover.
Installing an expansion card
To install an expansion card:
1
Remove the computer cover.
2
Locate an empty PCI Express or PCI slot on the mainboard.
3
Remove the bracket lock that holds the bracket to the computer. Save the
lock.
4
Pull out the bracket on the housing opposite the selected empty slot.
5
Remove the expansion card from its protective packaging.
6
Align the card in the empty bracket and then insert it into the slot. Make sure
that the card is properly seated.
7
Secure the card to your computer with the bracket lock you removed earlier.
8
Replace the computer cover.
When you turn on the computer, BIOS automatically detects and assigns resources
to the newly installed devices.
Note: If you want to replace or upgrade any of these components,
contact your dealer or a qualified service technician for assistance.
4 Frequently
asked
questions
English
16
4 Frequently asked questions
Frequently asked questions
The following questions indicate possible situations that may arise during the use of
your computer and each is followed by easy answers and solutions.
I pressed the power switch but the system did not boot up.
Check the LED located above the power switch.
If the LED is not lit, no power is being applied to the system. Try the following:
•
Check if the voltage selector switch located on the rear panel of the computer
is set to the correct voltage.
•
Check if you properly plugged the power cable into an electrical outlet.
•
If you are using a power strip, make sure it is plugged in and turned on.
If the LED is lit, check the following:
•
Is a nonbootable (nonsystem) disc in a drive? If yes, remove or replace it with a
system disc and press <Ctrl> + <Alt> + <Del> to restart your computer.
Nothing appears on the screen.
•
Check that the cable is correctly attached to the computer and the monitor.
Your computer's power management function automatically blanks the screen to
save power. Just press any key to turn the display back on.
If pressing a key does not work, you can restart your computer. If restarting your
computer does not work, contact your dealer or technical support center for
assistance.
The printer does not work.
Do the following:
•
Make sure the printer is connected to a power outlet and that it is turned on.
•
Make sure the printer cable is connected securely to the correct ports on the
computer and the printer.
•
For additional information concerning the printer, refer to the printer's
documentation.
17
Check the following:
•
The volume may be muted. Look for the Volume icon on the taskbar. If it is
crossed-out, click on the icon and deselect the Mute option. You can also
press the volume control/mute knob on your USB keyboard to toggle from
mute to sound on.
•
If headphones, earphones or external speakers are connected to the line-out
jack of your computer, the internal or built-in speakers are automatically turned
off.
System cannot read diskette, hard disk, CD or DVD information.
Check the following:
•
Make sure you are using the correct type of disk.
•
Make sure the CD or DVD is inserted into the drive correctly.
•
Check if the CD or DVD is clean and unscratched.
•
Check your drive by using a good (undamaged) disk. If your drive can not read
the information on the good disk there may be a problem with the drive.
Contact your dealer or technical support center for assistance.
System cannot write data on the hard disk or CD-R/CD-RW.
Check the following:
•
Make sure the hard disk is not write-protected.
•
Make sure you are using the correct type of disc.
English
No sound comes out from the computer.
English
18
4 Frequently asked questions
5 Regulations
and safety
notices
English
20
5 Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
device generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the device and receiver.
•
Connect the device into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to
maintain compliance with FCC regulations. In compliance with FCC regulations,
use shielded cables to connect to other computing devices. A dual-link cable is
recommended for DVI output.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply
with the Class B limits may be attached to this equipment. Operation with noncertified peripherals is likely to result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void
the user's authority, which is granted by the Federal Communications Commission,
to operate this computer.
21
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Hereby, Acer, declares that this PC series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian / Ukraine regulatory certification
Modem notices
Notice for USA
This equipment complies with Part 68 of the FCC rules. Located on the modem is a
label that contains, among other information, the FCC Registration Number and
Ringer Equivalence Number (REN) for this equipment. Upon request, you must
provide this information to your telephone company.
If your telephone equipment causes harm to the telephone network, the telephone
company may discontinue your service temporarily. If possible, they will notify you
in advance. But, if advance notice is not practical, you will be notified as soon as
possible. You will also be informed of your right to file a complaint with the FCC.
English
Operation conditions
English
22
5 Regulations and safety notices
Your telephone company may make changes in its facilities, equipment, operations,
or procedures that could affect the proper functioning of your equipment. If they do,
you will be notified in advance to give you an opportunity to maintain uninterrupted
telephone service.
If this equipment should fail to operate properly, disconnect the equipment from the
phone line to determine if it is causing the problem. If the problem is with the
equipment, discontinue use and contact your dealer or vendor.
Caution: To reduce the risk of fire, use only No. 26 AWG or larger
UL Listed or CSA Certified Telecommunication Line Cord.
TBR 21
This equipment has been approved [Council Decision 98/482/EC - "TBR 21"] for
single terminal connection to the Public Switched Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in different
countries, the approval does not, of itself, give an unconditional assurance of
successful operation on every PSTN termination point. In the event of problems,
you should contact your equipment supplier in the first instance.
Notice for Australia
For safety reasons, only connect headsets with a telecommunications compliance
label. This includes customer equipment previously labelled permitted or certified.
Notice for New Zealand
1
The grant of a Telepermit for any item of terminal equipment indicates only that
Telecom has accepted that the item complies with minimum conditions for
connection to its network. It indicates no endorsement of the product by
Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item of
Telepermitted equipment of a different make or model, nor does it imply that
any product is compatible with all of Telecom's network services.
2
This equipment is not capable, under all operating conditions, of correct
operation at the higher speeds for which it is designed. Telecom will accept no
responsibility should difficulties arise in such circumstances.
3
Some parameters required for compliance with Telecom's Telepermit
requirements are dependent on the equipment (PC) associated with this
device. The associated equipment shall be set to operate within the following
limits for compliance with Telecom's Specifications:
a
There shall be no more than 10 call attempts to the same number
within any 30 minute period for any single manual call initiation,
and
23
The equipment shall go on-hook for a period of not less than 30
seconds between the end of one attempt and the beginning of
the next call attempt.
4
Some parameters required for compliance with Telecom's Telepermit
requirements are dependent on the equipment (PC) associated with this
device. In order to operate within the limits for compliance with Telecom's
specifications, the associated equipment shall be set to ensure that automatic
calls to different numbers are spaced such that there is not less than
5 seconds between the end of one call attempt and the beginning of another.
5
This equipment shall not be set up to make automatic calls to Telecom's 111
Emergency Service.
6
This device is equipped with pulse dialing while the Telecom standard is DTMF
tone dialing. There is no guarantee that Telecom lines will always continue to
support pulse dialing.
7
Use of pulse dialing, when this equipment is connected to the same line as
other equipment, may give rise to bell tinkle or noise and may also cause a
false answer condition. Should such problems occur, the user should NOT
contact the telecom Fault Service.
8
This equipment may not provide for the effective hand-over of a call to another
device connected to the same line.
9
Under power failure conditions this appliance may not operate. Please ensure
that a separate telephone, not dependent on local power, is available for
emergency use.
Laser compliance statement
The CD or DVD drive used with this computer is a laser product.
The CD or DVD drive's classification label (shown below) is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE
TO BEAM.
Digital audio output statement
The optical connector contains no laser or light emitting diode (LED) more than
Class I.
Radio device regulatory notice
Note: Below regulatory information is for models with wireless LAN
and/or Bluetooth only.
English
b
English
24
5 Regulations and safety notices
List of applicable countries
This device must be used in strict accordance with the regulations and constraints
in the country of use. For further information, please contact local office in the
country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm for
the lastest country list.
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject to
licensing.
25
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. Easy Lai, e-mail:[email protected]
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921, Fax: +39-02 9399-2913, www.acer.it
Hereby declare that:
Product:
Trade Name:
Model Number:
SKU Number:
Personal Computer
Acer
AcerSystem
XXX-xxx (“x” = 0~9, a ~ z, A ~ Z or Blank)
Is compliant with the essential requirements and other relevant provisions of the
following EC directives, and that all the necessary steps have been taken and are in
force to assure that production units of the same product will continue comply with
the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following
harmonized standards:
-. EN55022, AS/NZS CISPR22, Class B
-. EN55024
-. EN55013 (Applicable to product built with TV tuner module)
-. EN55020 (Applicable to product built with TV tuner module)
-. EN61000-3-2 Class D
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
-. EN60950-1
-. EN60065 (Applicable to product built with TV tuner module)
Council Decision 98/482/EC (CTR21):
-. (Applicable to product with pan- European single terminal connection
to the Public Switched Telephone Network (PSTN).)
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous
Substances in Electrical and Electronic Equipment
-. The maximum concentration values of the restricted substances by
weight in homogenous material are:
Lead
0.1%
Polybrominated Biphenyls (PBB’s)
0.1%
Mercury
0.1%
Polybrominated Diphenyl Ethers (PBDE’s)
0.1%
Hexavalent 0.1%
Cadmium
0.01%
Chromium
English
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,
New Taipei City 221, Taiwan
English
26
Directive 2009/125/EC with regard to establishing a framework for the setting
of ecodesign requirements for energy-related product.
The standards listed below are applied to the product if built with WLAN
module or wireless keyboard and mouse.
R&TTE Directive 1999/5/EC as attested by conformity with the following
harmonized standard:
• Article 3.1(a) Health and Safety
-. EN60950-1
-. EN62311
• Article 3.1(b) EMC
-. EN301 489-1
-. EN301 489-3 (Applicable to non-bluetooth wireless keyboard mouse
set).
-. EN301 489-17
• Article 3.2 Spectrum Usages
-. EN300 440-2 (Applicable to non-bluetooth wireless keyboard mouse
set).
-. EN300 328
-. EN301 893 (Applicable to 5GHz high performance RLAN).
Year to begin affixing CE marking 2011.
Feb. 18, 2011
Easy Lai /Manager
Regulation Center, Acer Inc.
Date
27
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:
Product:
Personal Computer
Trade Name:
Acer
Model Number:
AcerSystem
SKU Number:
XXX-xxx,
("x" = 0~9, a ~ z, A ~ Z or Blank)
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
English
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Remark: All images are for reference purposes only.
Actual configuration may vary.
V12A2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement