PRODUCTION RANGE www.affri.com HARDNESS

PRODUCTION RANGE www.affri.com HARDNESS
PRODUCTION RANGE
HARDNESS
TESTERS
www.affri.com
AFFRI
®
ISO 9001:2000 REGISTERED
AFFRI
uces
d
o
r
t
I in
R
F
F
atic
A
m
o
t
em
u
an a ster syst
esste uture
n
d
r
ha
he f
for t
®
Since 1964 AFFRI ® has being producing hardness
testers combining test loads together with innovative
devices which, together, make up the AFFRI SYSTEM®.
The power supply can be mechanical, electromechanical, hydro-mechanical or pneumo-mechanical.
The AFFRI SYSTEM® has long surpassed the traditional
philosophies using dead-weights and elevating screws
found in conventional hardness testers.
The novel AFFRI SYSTEM ® is protected by patents
registered over the years.
An increase in operational performance had already
been obtained using closed-loop load control (Patent
AFFRI® N. 1175158), however, even this improvement is
moderate in comparison with the high qualitative and
practical performance levels reached by the AFFRI
SYSTEM®.
A further improvement in performance was achieved
when AFFRI ® made the hardness tester, working in
Rockwell and Brinell tests,truly automatic: a single
initiation starts and performs the continous test
sequence comprising positioning ,automatic contact and
measurement.
The fully automatic control ensures that the speed
throughout the entire test cycle remains unchanged even
in the load-cell version due to the leading technology of
the AFFRI SYSTEM® (patent pending).
Head office (Induno Olona Italy)
Manufacturing unit (Induno Olona - Italy)
Northern Europe sales and service (Brussells- Belgium)
®
AFFRI® instruments conform to International Standards
and are fully certified by International Calibration Laboratory.
Certification by direct and indirect method
STEELS AND CAST IRON
R
o
l
l
s
B
R
I
N
E
L
L
HB30
497
485
475
462
450
440
433
423
413
405
395
387
377
368
359
350
341
332
323
314
306
298
290
283
276
269
262
256
250
244
239
234
225
216
210
205
200
195
190
185
180
176
172
169
165
162
159
156
153
150
146
144
141
139
137
135
132
130
127
125
123
121
119
117
116
112
110
108
107
106
104
103
101
100
98
97
95
94
92
90
89
88
86
84
83
81
80
N.mm2 Kg/mm2 HV30 HB30
AFFRI
R
O
C
K
W
E
L
L
C
S
H
O
R
E
D
68
67
105
66
104
65
103
64
101
63
99
62
97
61
94
60
92
59
90
58
87
57
84
56
81
55
79
54
77
53
76
52
74
51
72
50
70
49
69
48
68
47
67
46
65
45
64
44
63
43
61
42
59
41
58
40
56
39
55
38
54
37
53
36
52
35
51
34
50
33
49
32
48
31
46
30
45
29
44
28
43
27
42
26
41
25
40
24
39
23
38
22
21
37
20
36
35 18.5
34 16.5
15
33
14
32
- 12.5
11
31
9.5
8
S
7
H
6
O
4.5
R
3
E
2
D
0
R
O
C
K
W
E
L
L
D
R
O
C
K
W
E
L
L
A
77
76
75.5
74.5
74
73
72.5
71.5
71
70
69
68.5
67.5
67
66
65.5
64.5
64
63
62
61.5
60.5
60
59
58.5
57.5
57
56
55.5
54.5
54
53
52.5
51.5
50.5
50
49
48.5
47.5
47
46
45.5
44.5
44
43
42.5
41.5
41
40
85.5
85
84.5
84
83.5
83
82.5
81.5
81
80.5
80
79.5
79
78.5
78
77.5
77
76.5
76
75.5
74.4
74
73.5
73
72.5
72
71.5
71
70.5
70
69.5
69
68.5
68
67.5
67
66.5
66
65.5
65
64.5
64
63.5
63
62.5
62
61.5
61
60
D
A
S
U
P
E
R
S
U
P
E
R
R
R
R
O
O
O
C
C
C
K
K
K
W
W
W
E
E
E
L
L
L
L
L
L
45 N 30 N 15 N
75.5
74.5
73
72
71
70
69
67.5
66.5
65.5
64
63
62
61
59.5
58.5
57.5
56
55
54
52.5
51.5
50
49
48
46.5
45.5
44.5
43
42
41
39.5
38.5
37
36
35
33.5
32.5
31.5
30
29
28
26.5
25.5
24
23
22
20.5
19.5
84.5
83.5
83
82
81
80
79
78.5
77.5
76.5
75.5
75
74
73
72
71
70.5
69.5
68.5
67.5
66.5
66
65
64
63
62
61.5
60.5
59.5
58.5
57.5
56.5
56
55
54
53
52
51.5
50.5
49.5
48.5
47.5
47
46
45
44
43
42
41.5
SCALE
93.3
93
92.5
92
91.5
91
90.5
90
89.5
89
88.5
88
87.5
87
86.5
86
85.5
85
84.5
84
83.5
83
82.5
82
81.5
81
80.5
80
79.5
79
78.5
78
77
76.5
76
75.5
75
74.5
74
73.5
72.5
72
71.5
71
70.5
70
69.5
TEST METHOD
ROCKWELL indenter
HR15N
HR30N
HR45N
HR15T
HR30T
HR45T
LOAD
N
∇ 120°
∇ 120°
∇ 120°
Ø 1/16”
Ø 1/8”
Ø 1/16”
Ø 1/16”
Ø 1/8”
HRC
HRA
HRD
HRB
HRE
HRF
HRG
HRK
1471
588
981
981
981
588
1471
1471
Superficial Rockwell
∇ 120°
∇ 120°
∇ 120°
Ø 1/16”
Ø 1/16”
Ø 1/16”
HB 10/3000
HB 5/750
HB 2.5/187.5
HB 2.5/62.5
HB 10/500
HB 5/125
HB 2.5/31.2
BRINELL
Ø 10 (HB 30)
Ø 5 (HB 30)
Ø 2.5 (HB 30)
Ø 2.5 (HB 10)
Ø 10 (HB 5)
Ø5
(HB 5)
Ø 2.5 (HB 5)
HV10
HV15
HV30
HV60
VICKERS
136
136
136
136°
ball
S
U
P
E
R
F
o
r
HARDNESS
CONVERSION
TABLE FOR
METALS
147
294
441
147
294
441
29430
7357
1839
613
4905
1226
306
981
147
294
588
diamond
V
I
C
K
E
R
S
HV30
1710
1663
1556
1478
1400
1323
1245
1160
1076
1004
940
903
870
840
813
787
762
738
715
693
672
652
632
T
T
612
E
E
593
N
N
575
S
S
558
I
I
542
L
L
526
510
σ
N.mm2 Kg/mm2 495
480
466
157
1540
453
150
1471
440
146
1432
428
143
1402
416
140
1373
404
136
1334
392
133
1304
381
130
1275
370
127
1245
360
124
1216
350
120
1177
341
117
1147
332
114
1118
323
111
1088
314
108
1059
306
105
1030
298
102
1000
290
99
971
283
97
951
276
94
922
269
92
902
262
89
873
256
87
853
250
85
833
244
84
824
239
82
804
234
80
784
225
77
755
216
74
725
210
72
706
205
70
686
200
68
667
195
67
657
190
65
637
185
63
618
180
62
608
176
60
588
172
59
578
169
57
559
165
56
549
162
55
539
159
54
529
156
53
519
153
52
510
150
51
500
146
50
490
144
141
48
470
139
137
135
47
461
132
130
45
441
127
125
43
421
123
121
42
412
119
117
41
402
116
112
110
39
382
108
107
106
37
362
104
103
101
35
343
100
98
97
33
323
95
94
92
90
31
304
89
88
86
30
294
84
83
29
284
81
80
28
274
45 N 30 N 15 N
Minimum thickness measurable
ROCKWELL ∇ Diam
F
HRC
20
HR15N
HR30N
HR45N
HRA
HRC
0.41
0.69
0.91
1.0
1.8
METALTESTER 0.38
C
30
40
50
60
70
0.33
0.58
0.77
0.9
1.6
0.32
0.26
0.47
0.63
0.8
1.4
0.26
0.19
0.36
0.50
0.7
1.2
0.20
0.14
0.26
0.37
0.6
1.0
0.14
0.09
0.17
0.25
0.5
0.8
0.08
300
400
500
Minimum thickness measurable
BRINELL
ø
F
mm
N
HB
40
60
2.5 1839 (HB / 30)
5 1226 2.0
1.3
10 9810 8.0
5.3
10 29430 (HB / 30)
METALTESTER
80
1.0
4.0
Scale 80-500 0.63
0.53 0.42
0.32
100
150
2.40
0.80
3.2
9.6
0.53
0.27
1.60 1.20 0.80 0.60 0.48
0.53
(HB / 5)
2.1
1.6
(HB / 10)
6.3
4.8
3.2
2.4 1.9
0.42 0.32 0.22 0.16 0.10
0.15 0.10
Scale 40 - 200
Minimum thickness measurable
200
VICKERS ∇ Diam
F
Kg
20
50
100
200
300
HV
400
600
800 1000
HV0.200
HV1
HV2
HV5
HV10
METALTESTER
METALTESTER/2
0.19
0.43
0.62
1.0
1.4
0.70
0.65
0.12
0.28
0.39
0.62
0.87
0.60
0.55
0.09
0.19
0.28
0.44
0.62
0.50
0.45
0.06
0.14
0.19
0.31
0.43
0.37
0.30
0.05
0.12
0.16
0.25
0.36
0.32
0.28
0.04
0.10
0.14
0.22
0.31
0.26
0.20
0.04
0.08
0.12
0.18
0.25
0.18
0.10
0.03
0.07
0.10
0.15
0.22
0.08
0.06
0.03
0.06
0.09
0.14
0.19
0.06
0.05
AFFRI ® Via M. Tagliaferro, 8 • 21056 INDUNO OLONA • VARESE - ITALIA
Tel. +39 0332.201533 / +39 0332.206289 • Fax +39 0332.203621
E-Mail [email protected] • www.affri.com
NON FERROUS METALS
R
O
C
K
W
E
L
L
G
V
I
C
K
E
R
S
HV
B
R
I
N
E
L
L
HB 5
198
195
191
188
185
182
179
176
173
171
168
165
163
160
157
156
153
151
149
147
145
142
140
138
136
134
132
131
129
126
125
124
122
120
118
117
115
114
113
112
111
109
108
107
106
105
104
103
102
101
100
98
97
96
95
94
93
92
91
90
88
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
69
67
65
64
63
61
59
58
56
55
53
52
51
50
48
47
45
44
42
41
40
38
37
36
33
31
28
26
23
21
19
16
HV
195
189
184
179
175
171
167
163
160
157
154
151
148
145
142
140
137
135
133
130
128
126
124
122
120
118
116
114
112
110
109
107
106
104
102
101
99
98
96
95
94
92
91
90
89
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
54
53
52
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
28
26
24
22
21
20
18
16
14
12
HB 5
92
91
90
89
88
87
86
85
82
81
79
77
76
72
74
71
69
67
66
65
62
61
59
57
56
54
52
51
49
47
46
44
42
41
39
G
S
U
P
E
R
R
O
C
K
W
E
L
L
K
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
K
R
O
C
K
W
E
L
L
B
R
O
C
K
W
E
L
L
A
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
B
61
60
59.5
59
58
57.5
57
56.5
56
55.5
55
54
53.5
53
52.5
52
51
50.5
50
49.5
49
48.5
48
47
46.5
46
45.5
45
44.5
44
43.5
43
42.5
42
41.5
41
40.5
40
39.5
39
38.5
38
37.5
37
36.5
36
35.5
35
34.5
34
33.5
33
32.5
32
31.5
31
30.5
30
29.5
29
28.5
28
27.5
27
26.5
26
25.5
25
24.5
24
23.5
23
22.5
22
21.5
21
20.5
20
A
R
O
C
K
W
E
L
L
E
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
54
52
51
50
48
46
44
42
40
38
36
33
30
27
24
21
17
14
E
R
O
C
K
W
E
L
L
F
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
54
52
51
50
49
47
46
44
42
40
38
36
32
29
26
23
19
16
F
R
O
C
K
W
E
L
L
45 T
72
71
70
69
68
67
66
65.5
64.5
63.5
62
61
60.5
59.5
58.5
58
57
56
55
54
53
52
51
50
49
48.5
47
46.5
45.5
44
43
42.5
41.5
40.5
39.5
38.5
37.5
36.5
35.5
34.5
33.5
32
31
30
29
28
27
26
25
24
23
22
20.5
19.5
18.5
17
16
15.5
14.5
13.5
12.5
11
10
9
S
U
P
E
R
R
O
C
K
W
E
L
L
30 T
82
81.5
81
80.5
80
79
78.5
78
77.5
77
76
75.5
75
74.5
74
73.5
73
72
71.5
71
70
69.5
69
68
67.5
67
66
65.5
65
64
63.5
62.5
62
61.5
60.5
60
59.5
58.5
58
57
56.5
56
55
54.5
54
53
52.5
51.5
51
50.5
49.5
49
48.5
47.5
47
46
45.5
45
44
43.5
43
42
41.5
40.5
40
45 T 39.5
38.5
38
37.5
36.5
36
35.5
34.5
34
33
32.5
32
31
30.5
29.5
29
28.5
27.5
27
26
25.5
25
24
23.5
23
22.3
21.5
20.4
20
S
U
P
E
R
R
O
C
K
W
E
L
L
15 T
93
92.3
92
91.5
91
90.5
90
89.5
89
88.5
88
87.5
87
86.5
86
85.5
85
84
64
83.5
83
82.5
82
81.5
81
80.5
80
79.5
79
78.5
78
77.5
77
76.5
76
75.5
75
74.5
74
73.5
73
72.5
72
71.5
71
70.5
70
69.5
69
68.5
68
67.5
67
66.5
66
65.5
64
63.5
30 T 15 T
R O C K W E L L
SCALE
SYMBOL
PENETRATOR
MINOR LOAD MAJOR LOAD
N
N
HRA
CONE 120°
98
588
Hardened Metals, cementation layers, thin sheet (>0.4 mm)
HRB
BALL 1/16”
98
981
Non-ferrous metals, construction steel
HRC
CONE 120°
98
1471
HRD
CONE 120°
98
981
Cementated surface with a medium layer of cementation
HRE
BALL 1/8”
98
981
Cast iron, alloy magnesium aluminium, anti-friction metals, plastic (ASTM D785-60T)
HRF
BALL 1/16”
98
588
Alloy copper, sheet (> 0.6 mm.)
HRG
BALL 1/16”
98
1471
HRH
BALL 1/8”
98
588
HRK
BALL 1/8”
98
1471
HRL
BALL 1/4”
98
588
Like HRK, hard rubber (AS TM D 530-59 T) synthetic materials (ASTM D 785-60 T)
HRM
BALL 1/4”
98
981
Like HRK and HRL, chipboard panels (ASTM D 805-52)
HRP
BALL 1/4”
98
1471
Like HRK, HRL, HRM
HRR
BALL 1/2”
98
588
Like HRK, HRL, HRM
HRS
BALL 1/2”
98
981
Like HRK, HRL, HRM
HRV
BALL 1/2”
98
1471
R O C K W E L L
HR30N
S U P E R F I C I A L
HR15N
HR30W
CONE 120°
V I C K E R S
294
HR15T
147
BALL 1/16”
29.4
294
HR45T
441
HR15W
147
BALL 1/8”
29.4
294
HR45W
441
HR15X
147
BALL 1/4”
29.4
294
HR45X
441
HR15Y
147
HR30Y
BALL 1/2”
HR45Y
B R I N E L L
29.4
441
HR30X
Tempered, cemented, hardened and quenched Steel
Phosphorous bronze, beryllium copper, medium hardness tempered cast iron
Aluminium, zinc, lead abrasive stone
Anti-friction metals and reduced hardness metals
Like HRK, HRL, HRM, HRP, HRR, HRS
147
HR45N
HR30T
FIELD OF APPLICATION
29.4
147
Like HRA, HRC, HRD but for layers or thin sheet (> 0.15 mm)
Like HRB, HRF, HRG but for thin sheet (> 0.25 mm)
Softer metals, in thin layers eg thin anti-friction metal covering
Sinterised metals (ASTM B 347-59 T)
Like HRX
441
HV3
PIRAMID 136°
29.4
All metals (hard and soft)
HV10
PIRAMID 136°
98
All metals (hard and soft)
HV15
PIRAMID 136°
147
All metals (hard and soft)
HV30
PIRAMID 136°
294
All metals (hard and soft)
HV60
PIRAMID 136°
588
All metals (hard and soft)
HB T 30 C
2.5 Carbide ball
1839
Cast iron, steel with hardness above 400 HB
HB T 30 S
2.5 Carbide ball
1839
Cast iron, steel with hardness below 400 HB
HB T 10
2.5 Carbide ball
613
Aluminium, bronze, copper, brass
HB 2.5
2.5 Carbide ball
153
Aluminium, bronze, copper, brass
HB 5
2.5 Carbide ball
306
Aluminium, bronze, copper, brass
HB 2.5
5 Carbide ball
1226
Aluminium, bronze, copper, brass
HB 1.25
10 Carbide ball
1226
Aluminium, bronze, copper, brass
HB 30
2.5 Carbide ball
1839
Steel, cast iron
AFFRI
INDEX
page
REFERENCE HARDNESS TESTER .............................................................................................. 2
AUTOMATIC ROCKWELL - BRINELL
3302 MRS........................................................................................ 4
3332 MRS / MRS A......................................................................... 5
250 MRS.......................................................................................... 6
330 RSD / 330 RS-SD ................................................................... 6
330 RS / 330 RS-S ......................................................................... 7
270 RSD / 270 RS-S....................................................................... 7
270 RS / 270 RS-S ......................................................................... 8
331 RSD / 331 RS-SD..................................................................... 8
331 RS / 331 RS-S ......................................................................... 9
206 RSD DIGITRONIC 206 RS-SD DIGITRONIC.............................. 9
206 RS / 206 RS-S ....................................................................... 10
ROCKWELL - BRINELL
206 RT / 206 RTS ......................................................................... 11
206 RTD / 206 RTSD..................................................................... 11
206 EX / 206 EXS ........................................................................... 12
250 DRM ......................................................................................... 13
206 MX / 206 MXS......................................................................... 13
PORTABLES
HARD TEST-I.................................................................................... 14
HARD TEST-II .................................................................................. 14
METALTESTER MKII ........................................................................ 15
METALTEST...................................................................................... 16
MICROTESTER................................................................................. 16
EDA300............................................................................................ 17
HT-1000 / HT-2000......................................................................... 18
MICRO VICKERS
DM-8................................................................................................ 19
DM-2................................................................................................ 20
DM-2 AUTO and DM-8 AUTO - TEST REPORT ............................... 21
DM-5................................................................................................ 22
UNIVERSAL ROCKWELL - VICKERS - BRINELL
INTEGRAL 6 ..................................................................................... 23
INTEGRAL ........................................................................................ 24
INTEGRAL - E .................................................................................. 25
270 VRSD / 270 VRSA.................................................................... 26
270 VRSTV ...................................................................................... 26
251 VRSD / 251 VRSA.................................................................... 27
251 VRSTV ...................................................................................... 27
LD 250 ............................................................................................. 28
LD 3000 ......................................................................................... 29
VIDEO MEASUREMENT
ACCESSORIES FOR MISURE BRINELL - VICKERS ......................... 30
EASY BRINELL................................................................................. 30
AUTOMATIC BRINELL
CK3000............................................................................................ 31
AUTO3000 ....................................................................................... 31
AUTOMATIC ROCKWELL - BRINELL HIGH SPEED
330 PRS .......................................................................................... 32
IN-LINE CUSTOM SOLUTIONS
MATRIX............................................................................................ 33
AUTO BRINELL- ROCKWELL ........................................................... 34
AUTO GM ......................................................................................... 34
AUTO PRS ........................................................................................ 35
AUTOMATIC BOLTS ......................................................................... 35
CUSTOMIZED SOLUTION
HB TWIN .......................................................................................... 36
GAS BOTTLE .................................................................................... 36
HB AUTO TUBE ................................................................................ 37
AUTOMATIC BRINELL “RADIAL”..................................................... 37
HB OPTI ........................................................................................... 38
METALTESTER F1............................................................................ 38
3302 R............................................................................................. 38
FOR PLASTIC MATERIALS
SHORE SERIES ................................................................................ 39
ELECTRONIC HARDNESS TESTER .................................................. 40
IRHD................................................................................................. 41
PJ 0-100 ......................................................................................... 41
ACCESSORIES
DIAMOND INDENTERS .................................................................... 42
STANDARD TEST BLOCKS............................................................... 44
HOW TO READ AFFRI’S CATALOGUE
P
M
RS
S
D
RT
Motorized pneumatic action
Motorized electrical action
Rockwell semiautomatic« AFFRI SYSTEM » inside
Superficial Rockwell
Digital
Traditional Rockwell system (manual cycle)
EX
MX
V
TV
VM
Economic Rockwell manual cycle
Economic Rockwell motorized cycle
Vickers
Vision trough camera
Vickers Micro
®
AFFRI
REFERENCE HARDNESS TESTER
®
Reference Hardness Tester for calibration laboratories
This highly accurate Hardness Tester is designed for laboratories calibrating Test Blocks. It includes Affri System technology and a fully automatic system to perform calibration in accordance with the International Standards ASTM, EN ISO-JIS .
• Integral AFFRI System
• Absolute measurement
• The Start button initiates an uninterrupted test sequence comprising:
- approach the piece
- clamping
- impression of reference surface
- complete measurement cycle with subsequent release
• The result is not influenced by deflections during the test cycle
• Large and fixed table supporting test pieces
Designed for different applications: A) EN ISO 6508-3 for Rockwell; B) EN ISO 6508-3 for Super Rockwell; C) EN ISO 6506-3 for Brinell; D) EN ISO 6507-3 for Vickers
The excellent accuracy and repeatability fully meet the requisite standards. A table of practical results obtained on AFFRI machines and another reference machine shows
AFFRI’s high comparable performance (➀):
The integral Affri system of this machine operates on the same principle as that adopted in the regular production machines shown this catalogue.
Values obtained with Master reference hardness tester and with Affri
reference hardness tester using the same indenter and test blocks for
the range (26 HRC, 44 HRC, 65 HRC)
➀
Nominal Hardness
26 HRC
Nominal Hardness
65 HRC
Master
AFFRI
Master
AFFRI
Master
AFFRI
Reference Reference Reference Reference Reference Reference
Tester
Tester
Tester
Tester
Tester
Tester
(HRC)
(HRC)
(HRC)
(HRC)
(HRC)
(HRC)
AUTO CONTACT WITH TEST PIECE AND
AUTOMATIC TEST CYCLE
Average
Standard
deviation
2
Nominal Hardness
44 HRC
26.05
26.13
26.20
26.32
26.34
26.34
26.64
26.25
26.18
26.21
44.27
44.28
44.29
44.25
44.24
44.31
44.34
44.32
44.32
44.32
64.99
65.04
65.11
65.07
65.16
65.17
65.12
65.16
65.20
65.16
26.21
0.12
26.32
0.19
44.27
0.02
44.32
0.01
65.07
0.07
65.16
0.03
REFERENCE HARDNESS TESTER VICKERS-BRINELL
AFFRI
Measure of the geometry on Rockwell, Vickers
indenters as per ISO 6508-3 ISO 6507-3
Reference Hardness Tester for calibration laboratories
This highly accurate Hardness Tester is designed for laboratories calibrating Test Blocks. It
includes Affri System technology and a fully automatic system to perform calibration in
accordance with the International Standards ASTM, EN ISO-JIS.
Designed for Vickere and Brinell as per ISO 6507-3, ISO 6506-3 Standards
• Integral AFFRI System
• Absolute measurement
• The Start button initiates an uninterrupted test
sequence comprising:
- approach the piece
- clamping
- impression of reference surface
- complete measurement cycle with subsequent
release
• The result is not influenced by deflections during the
test cycle
• Large and fixed table supporting test pieces
Automatic measure on Rockwell indenter profile
includine radium
Meaure of Vickers indenter profile and
coincidence at edge point
AUTO CONTACT WITH TEST PIECE AND
AUTOMATIC TEST CYCLE
3
®
AFFRI
AUTOMATIC ROCKWELL, BRINELL
®
AFFRI SYSTEM IS THE NEW GENERATION OF HARDNESS TESTERS
A SINGLE INPUT TO START in automatic sequence without interruption applies the minor and major load and measure the Rockwell
indentation automatically. All test operations are managed through a single start command to reduce operator fatigue and to increase test
repeatability and accuracy to the maximum.
AUTOMATIC CONTACT WITH THE TEST PIECE. The AFFRI® system can perform automatic contact with the test piece surface without moving
the piece. It automatically moves the indenter and the measuring system until contact is made, the piece is clamped, the force applied and
indentation is measured automatically on Rockwell, Vickers or Brinell procedure.
- The system is capable of measuring accurately even if the test piece deflects up to 50 mm during measurement. This automatic compensation
provide accurate results under adverse test conditions.
- External source of vibration don’t create any influence on result.
- The test piece is CLAMPED AUTOMATICALLY and locked in position before the test force (20 to 400 Kgf) is applied.
- The test forces are controlled test by test trough load cell and closed loop Affri system to assure high performance conform to ISO-JIS Standards.
- Perfect and effective measurments even at the first test with AFFRI® system inside
- Accuracy is stable in every condition
- No need to be levelled when installed
- It can be utilised by everybody also not schooling people only one start input and wait for test result
- An emergency push button is also included
3302 MRS
Technical characteristics (code 1404)
Preload
Rockwell loads
SuperRockwell loads
(10 Kgf) 98.07 N - (3 Kgf) 29.4 N
(10 60 100 150 Kgf) 98.10 588.60 981 1471.50 N
(3 15 30 45 Kgf) 29.43 147.15 294.30 441.45 N
Brinell loads
(5 6.25 10 15.6 25 30 31.2 62.5 125 187.5 Kgf - on request extra 250 Kgf)
49.05 61.3 98.1 153.23 245 294.43 306.5 613 1226 1839 N (on request 2452)
Vickers Knoop loads
(3 5 10 15 20 30 60 100 Kgf)
29.43 49.05 98.1 147.15 196 294.3 588.6 981 N
Optional test loads
49 132 358 961 N (for plastic, rubber as per EN-ISO 2039 std)
(250 Kgf) 2452.5 N Brinell
A-B-C-D
Shore
Accuracy: Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 - EN-ISO 2039 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Superficial Rockwell HRN+HRT
Brinell HB 30, HB 10, HB 5, HB 2.5; Break Nmm2
Vickers (indentations only)
EN-ISO 2039
Mode of operation
automatic with load cell and closed loop Affri patent
Only one start input moves down head to reach and clamp the test surface from 0 to 400 mm distance and
Action automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece
from 0 to 400 mm
Mobile Indenter
100 N
Self clamping
Self aligning to test surface from 0 to 400 mm
Automatic compensation of deflection piece from 0 to 400 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Digital reading
Rockwell - Brinell (Vickers conversion) Resolution: 0.1 HR - 0.1HB ( 0.01 HR unit, at request)
Total height capacity
400 mm motorized (more upon request)
Total depth capacity
200 mm
330x390 mm
Dimension of base
Max load of test piece
2000 Kg
Power supply
220V 50÷60Hz - 200VA
Fields of application: for all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastics
Net weight
120 Kg
Packing weight
160 Kg
70x72xH190
Packing measurements
4
AFFRI
AUTOMATIC ROCKWELL, BRINELL
3332 MRS / MRS A
Technical characteristics: 3332 MRS (code 1403)
3332 MRS A (code 1409)
Preload
Rockwell loads
SuperRockwell loads
(10 Kgf) 98.07 N - (3 Kgf) 29.4 N
(10 60 100 150 Kgf) 98.10 588.60 981 1471.50 N
(3 15 30 45 Kgf) 29.43 147.15 294.30 441.45 N
Brinell loads
(5 6.25 10 15.6 25 30 31.2 62.5 125 187.5 Kgf - on request extra 250 Kgf)
49.05 61.3 98.1 153.23 245 294.43 306.5 613 1226 1839 N (on request 2452)
Vickers Knoop loads
Optional test loads
Shore
Accuracy
(3 5 10 15 20 30 60 100 Kgf) 29.43 49.05 98.1 147.15 196 294.3 588.6 981 N
49 132 358 961 N (for plastic, rubber as per EN-ISO 2039 std) (250 Kgf) 2452.5 N Brinell
A-B-C-D
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 - EN-ISO 2039 / JIS
Rockwell HRC A D B F G L M R Brinell HB 30, HB 10, HB 5, HB 2.5; Break Nmm2
Superficial Rockwell HRN+HRT EN-ISO 2039
Mode of operation
automatic with load cell and closed loop Affri patent
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
Action
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece
from 0 to 50 mm
from 0 to 500 mm
Mobile Indenter
Self clamping
200 ÷ 4000 N
100 N
Self aligning to test surface from 0 to 50 mm
from 0 to 500 mm
Automatic compensation of deflection piece from 0 to 400 mm
Operativity
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Temperature range
+ 5° to + 50° C
Rockwell - Brinell (Vickers conversion) Resolution: 0.1 HR - 0.1HB ( 0.01 HR unit, at request)
Digital reading
from 0 to 50 mm multiples, till 400 mm
from 0 to 500 mm without break including test cycle
Floating head
400 mm (more upon request) manual
500 mm (more upon request) motorized
Total height capacity
200 mm
Total depth capacity
Dimension of base
330x390 mm
Max load of test piece
2000 Kg
Power supply
220V 50÷60Hz - 200VA
Fields of application: For all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastics
Net weight
100 Kg
140 Kg
Packing weight
Packing measurements
70x72xH100
Feasible tests
Twin
250 MRS
Technical characteristics (code 1405)
Preload
Rockwell loads
SuperRockwell loads
(10 Kgf) 98.07 N - (3 Kgf) 29.4 N
(10 60 100 150 Kgf) 98.10 588.60 981 1471.50 N
(3 15 30 45 Kgf) 29.43 147.15 294.30 441.45 N
Brinell loads
(5 6.25 10 15.6 25 30 31.2 62.5 125 187.5 Kgf - on request extra 250 Kgf)
49.05 61.3 98.1 153.23 245 294.43 306.5 613 1226 1839 N (on request 2452)
Vickers Knoop loads
Optional test loads
Shore
Accuracy
(3 5 10 15 20 30 60 100 Kgf) 29.43 49.05 98.1 147.15 196 294.3 588.6 981 N
49 132 358 961 N (for plastic, rubber as per EN-ISO 2039 std)
(250 Kgf) 2452.5 N Brinell
A-B-C-D
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 - EN-ISO 2039 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Superficial Rockwell HRN+HRT
Brinell HB 30, HB 10, HB 5, HB 2.5; Break Nmm2
EN-ISO 2039
automatic with load cell and closed loop Affri patent
Mode of operation
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
Action
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece
from 0 to 50 mm
Mobile Indenter
200 ÷ 4000 N
Self clamping
Self aligning to test surface from 0 to 50 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Digital reading
Rockwell - Brinell (Vickers conversion) Resolution: 0.1 HR - 0.1 HB - 0.1 HV (0.01 HR unit, at request)
Total height capacity
215 mm
Total depth capacity
190 mm
Max load of test piece
1000 Kg
Power supply
220V 50÷60Hz - 200VA
Fields of application: For all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastics
Net weight
75 Kg
Packing weight
90 Kg
Packing measurements
37x60x100 cm
5
®
AFFRI
AUTOMATIC ROCKWELL, BRINELL
®
AFFRI SYSTEM IS THE NEW GENERATION OF HARDNESS TESTERS
A SINGLE INPUT TO START in automatic sequence without interruption applies the minor and major load and measure the Rockwell
indentation automatically. All test operations are managed through a single start command to reduce operator fatigue and to increase test
repeatability and accuracy to the maximum.
AUTOMATIC CONTACT WITH THE TEST PIECE. The AFFRI® system can perform automatic contact with the test piece surface without moving
the piece. It automatically moves the indenter and the measuring system until contact is made, the piece is clamped, the force applied and
indentation is measured automatically on Rockwell, Vickers or Brinell procedure.
- The system is capable of measuring accurately even if the test piece deflects up to 50 mm during measurement. This automatic compensation
provide accurate results under adverse test conditions.
- External source of vibration don’t create any influence on result.
- The test piece is CLAMPED AUTOMATICALLY and locked in position before the test force (20 to 400 Kgf) is applied.
- The test forces are controlled test by test trough load cell Affri system to assure high performance conform to ISO-JIS Standards.
- Perfect and effective measurments even at the first test with AFFRI® system inside
- Accuracy is stable in every condition
- No need to be levelled when installed
- It can be utilised by everybody also not schooling people only one start input and wait for test result
330 RSD / 330 RS-SD
Technical characteristics: 330 RSD (code 1104)
330 RS-SD (code 1109)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN+HRT
Brinell HB 30; HB 5; HB 2.5
Manual
Mode of operation
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and automaAction tically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece; clamping of the
piece; activation of reference surface; entire test cycle performance and release of piece.
Mobile Indenter
from 0 to 50 mm multiples till 400 mm
Mobile clamping
from 0 to 50 mm multiples till 400 mm
Self aligning to test surface from 0 to 50 mm multiples till 400 mm
Automatic compensation of deflection piece from 0 to 50 mm
Operativity
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Temperature range
+ 5° to + 50° C
digital Rockwell+Brinell+R N N/mm2
Reading
digital Rockwell superficial
0.1 HRC - 0.1 HB
Reading resolution
0.1 HRN
400 mm (more upon request)
Total height capacity
200 mm
Total depth capacity
330x390 mm with T slots
Base
2000 Kg
Max load of test piece
200 ÷ 4000 N
Self clamping
Power supply
220V 50÷60Hz - 200VA
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with depth
Fields of application
brass, aluminium, copper, metal alloys, hard and
less to 0.6 mm
soft plastics with a higher thickness than 0.6 mm
100 Kg
Net weight
110 Kg
Packing weight
54x54x99 cm
Packing measurements
6
AFFRI
AUTOMATIC ROCKWELL, BRINELL
330 RS / 330 RS-S
Technical characteristics: 330 RS (code 1004)
330 RS-S (code 1008)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN+HRT
Brinell
Vickers
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm multiples till 400 mm
Mobile Indenter
from 0 to 50 mm multiples till 400 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm multiples till 400 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Read out
analogous automatic zeroing
Reading resolution
0.5 HRC
0.5 HRN
Total height capacity
400 mm (more upon request)
Total depth capacity
200 mm
Base
330x390 mm with T slots
Max load of test piece
2000 Kg
Self clamping
200 ÷ 4000 N
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with
Fields of application
brass, aluminium, copper, metal alloys, hard and
depth less to 0.6 mm
soft plastics with a higher thickness than 0.6 mm
100 Kg
Net weight
110 Kg
Packing weight
54x54x99 cm
Packing measurements
Action
270 RSD / 270 RS-SD
Technical characteristics: 270 RSD (code 1103)
270 RS-SD (code 1108)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN+HRT
Brinell HB 30; HB 5; HB 2.5
manual
Mode of operation
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
Action
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm multiples till 270 mm
Mobile Indenter
from 0 to 50 mm multiples till 270 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm multiples till 270 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
digital Rockwell+Rockwell+Break Nmm2
Reading
digitale Rockwell/Brinell
Reading resolution
0.1 HRC
0.1 HRN
Total height capacity
270 mm
Total depth capacity
170 mm
Base
270x330 mm
Max load of test piece
2000 Kg
Self clamping
200 ÷ 4000 N
220V 50÷60Hz - 200VA
Power supply
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with
brass, aluminium, copper, metal alloys, hard and soft
Fields of application
depth less to 0.6 mm
plastics with a higher thickness than 0.6 mm
Net weight
80 Kg
Packing weight
90 Kg
Packing measurements
54x54x99 cm
7
®
AFFRI
AUTOMATIC ROCKWELL, BRINELL
®
270 RS / 270 RS-S
Technical characteristics: 270 RS (code 1003)
270 RS-S (code 1007)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Rockwell sup. HRN+HRT
Feasible tests
Rockwell HRC A D B F G L M R
Brinell
Brinell HB 30; HB 10; HB 5; Break Nmm2
Twin
Vickers
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
Action
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm multiples till 270 mm
Mobile Indenter
from 0 to 50 mm multiples till 270 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm multiples till 270 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Read out
analogous
Reading resolution
0.5 HRC
0.5 HRN
Total height capacity
270 mm
Total depth capacity
170 mm
Base
270x330 mm with T slots
Max load of test piece
2000 Kg
Self clamping
200 ÷ 4000 N
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with
Fields of application
brass, aluminium, copper, metal alloys, hard and soft
depth less to 0.6 mm
plastics with a higher thickness than 0.6 mm
80 Kg
Net weight
90 Kg
Packing weight
54x54x99 cm
Packing measurements
331 RSD / 331 RS-SD
Technical characteristics: 331 RSD (code 1110)
331 RS-SD (code 1111)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN+HRT
Brinell HB 30; HB 5; HB 2.5
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm multiples till 270 mm
Mobile Indenter
from 0 to 50 mm multiples till 270 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm multiples till 270 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Read out
digital Rockwell/Brinell
digital Rockwell+Rockwell+R N N/mm2
Reading resolution
0.1 HRN
0.1 HRC
Total height capacity
270 mm
Total depth capacity
170 mm
Base
120x120 mm
Max load of test piece
2000 Kg
Self clamping
200 ÷ 4000 N
Power supply
220V 50÷60Hz - 200VA
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with depth
brass, aluminium, copper, metal alloys, hard and soft
Fields of application
less to 0.6 mm
plastics with a higher thickness than 0.6 mm
Net weight
100 Kg
110 Kg
Packing weight
Packing measurements
54x54x99 cm
Action
8
AFFRI
AUTOMATIC ROCKWELL, BRINELL
331 RS / 331 RS-S
Technical characteristics: 331 RS (code 1112)
331 RS-S (code 1113)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN+HRT
Brinell HB 30; HB 5; HB 2.5
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm multiples till 270 mm
Mobile Indenter
from 0 to 50 mm multiples till 270 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm multiples till 270 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Read out
analogous
Reading resolution
0.5 HRN
0.5 HRC
270 mm
Total height capacity
170 mm
Total depth capacity
Base
120x120 mm
2000 Kg
Max load of test piece
200 ÷ 4000 N
Self clamping
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with
brass, aluminium, copper, metal alloys, hard and soft
Fields of application
depth less to 0.6 mm
plastics with a higher thickness than 0.6 mm
100 Kg
Net weight
110 Kg
Packing weight
54x54x99 cm
Packing measurements
Action
206 RSD DIGITRONIC
206 RS-SD DIGITRONIC
Technical characteristics: 206 RSD DIGITRONIC (code 1102)
206 RS-SD DIGITRONIC (code 1107)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN + HRT
Brinell HB 30; HB 5; HB 2.5
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm
Mobile Indenter
from 0 to 50 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm
Automatic compensation of deflection piece from 0 to 50 mm
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
0.1 HRC
0.1HR N
Reading resolution
215 mm
Total height capacity
190 mm
Total depth capacity
1000 Kg
Max load of test piece
200 ÷ 4000 N
Self clamping
Piece selection transmission included
220V 50÷60Hz - 200VA
Power supply
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with
Fields of application
brass, aluminium, copper, metal alloys, hard and
depth less to 0.6 mm
soft plastics with a higher thickness than 0.6 mm
Net weight
68 kg
Packing weight
88 kg
Packing measurements
34x54x99 cm
Action
9
®
AFFRI
AUTOMATIC ROCKWELL, BRINELL
®
206 RS / 206 RS-S
Technical characteristics: 206 RS (code 1002)
206 RS-S (code 1006)
Preload
(10 Kgf) 98.07 N
(3 Kgf) 29.4 N
Test loads
(60-100-150 kgf) Rockwell 588-980-1471 N
(10-60-100 kgf) Vickers 98.07-588-980 N
(62.5-125-187.5 kgf) Brinell 612-1225-1839 N
(15-30-45 kgf) Rockwell 147-294-441 N
(3-15-30 kgf) Vickers 29-147-294 N
(15.6-31.2 kgf) Brinell 153-306 N
Accuracy
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Brinell HB 30; HB 10; HB 5; Break Nmm2
Rockwell sup. HRN + HRT
Brinell HB 30; HB 5; HB 2.5
Only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and
automatically starts the hardness cycle in automatic succession without breaking a phase: approach to the piece;
clamping of the piece; activation of reference surface; entire test cycle performance and release of piece.
from 0 to 50 mm
Mobile Indenter
from 0 to 50 mm
Mobile clamping
Self aligning to test surface from 0 to 50 mm
Automatic compensation of deflection piece from 0 to 50 mm
Operativity
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Temperature range
+ 5° to + 50° C
Analogic
Read out
0.5 HR
Reading resolution
0.5 HR
215 mm
Total height capacity
190 mm
Total depth capacity
1000 Kg
Max load of test piece
200 ÷ 4000 N
Self clamping
For all metals: iron, steel, tempered steel, cast iron,
Nitriding, cementation, hard facing with depth
brass, aluminium, copper, metal alloys, hard and soft
Fields of application
less to 0.6 mm
plastics with a higher thickness than 0.6 mm
68 kg
Net weight
88 kg
Packing weight
34x54x99 cm
Packing measurements
Action
10
AFFRI
ROCKWELL, BRINELL
How to use: Acting the hand wheel on the base will be performed indenter approach to the test block and acting up lever
will act load force for test cycle.
Force:
the test force is directly to the indenter axis and acted by mechanical dynamometer load cell inside.
Accuracy conform to ISO-JIS standards.
Performance: it can be utilised by everybody in a simple action
206 RT / 206 RTS
Technical characteristics: 206 RT (code 1001)
(10 kgf) 98.07 N
Test loads
(60-100-150kgf) Rockwell 588-980-1471N
(15-30-45kgf) Rockwell superficiale 147-294-441N
(10-60-100kgf) Vickers 98.07-588-980N
(3-15-30kgf) Vickers 29-147-294N
(62.5-125-187.5kgf) Brinell 612-1225-1839N (15.6-31.2kgf) Brinell 153-306N
Mode of operation
manual
Feasible tests
Twin
Rockwell HRC A-D-B-F-G-L-M-R
Brinell HB 30; HB 10; HB 5
Reading resolution
Accuracy
Operativity
Temperature range
Height capacity
Depth capacity
Diameter of column
Diameter of anvil
Max load of test piece
0.5 HR
0.5 HR
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
+ 5° to + 50° C
215 mm
190 mm
60 mm
60 mm
1000 Kg
For all metals, steel, hard steel, cast iron,
Nitriding, cementation, hard facing with
brass, aluminium over 0.6 mm, plastics, soft
depth less to 0.6 mm
and hard rubber
65 kg
85 kg
37x60x102 cm
Fields of application
Net weight
Packing weight
Packing measurements
206 RTD / 206 RTSD
206 RTS (code 1005)
Preload
Technical characteristics: 206 RTD (code 1101)
(3 kgf ) 29.4 N
Rockwell sup. HRN + HRT
Brinell HB 30; HB 5; HB 2.5 - HV - 3 - HV - 15
206 RTSD (code 1106)
Preload
(10 kgf) 98.07 N
Test loads
(60-100-150kgf) Rockwell 588-980-1471N
(15-30-45kgf) Rockwell superficiale 147-294-441N
(10-60-100kgf) Vickers 98.07-588-980N
(3-15-30kgf) Vickers 29-147-294N
(62.5-125-187.5kgf) Brinell 612-1225-1839N (15.6-31.2kgf) Brinell 153-306N
Mode of operation
manual
Feasible tests
Twin
Rockwell + Brinell + Vickers
Reading resolution
Accuracy
Operativity
Temperature range
Height capacity
Depth capacity
Diameter of column
Diameter of anvil
Max load of test piece
Fields of application
Net weight
Packing weight
Packing measurements
(3 kgf ) 29.4 N
Rockwell superficial + Brinell + Vickers
0.1 HR
0.2 HR
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
+ 5° to + 50° C
215 mm
190 mm
60 mm
60 mm
1000 Kg
For all metals, steel, hard steel, cast iron,
Nitriding, cementation, hard facing with
brass, aluminium over 0.6 mm, plastics, soft
depth less to 0.6 mm
and hard rubber
65 kg
85 kg
37x60x102 cm
11
®
AFFRI
ROCKWELL, BRINELL
®
206 EX / 206 EXS
Technical characteristics: 206 EX (code 1114)
(10 kgf) 98.07 N
29.4N (3 Kgf)
Test Load
588-980-1471 N Rockwell (60-100-150 Kgf)
98.07-588 N Vickers (10-60 Kgf)
147-294 - 441N Superficial Rockwell (15-30-45 Kgf)
29-147-294 N Vickers (3-15-30 Kgf)
Mode of operation
Feasible Tests
Twin
Reading
Reading resolution
Accuracy
Operativity
Temperature range
Height capacity
Depth capacity
Diameter of anvil
Max load of test piece
Data output
Power supply
Fields of application
Net weight
Packing weight
Packing measurements
12
206 EXS (code 1115)
Preload
Manual
Rockwell:
HRA; HRB; HRC; HRD; HRE; HRF; HRG; HRH; HRK
Superficial Rockwell:
Vickers: HV10; HV60; HV100 only indentation
HRA; HRB; HRC; HRD; HRE; HRF; HRG; HRH; HRK
Brinell (at your request):
Vickers: HV10; HV60; HV100
HB 2.5/62.5; HB2.5/187.5; HB 5/125
HBT 2.5/62.5; HBT 2.5/187.5; HBT 5/125
Rockwell 9 scale (HBT on request)
Rockwell 6 scale
0.2 HR (0.2 HB)
0.1 HR (0.1 HB)
Conformation standards EN-ISO 6508-2 / 6506-2 / JIS
it can works if not levelled, inclined or near to vibration area, without loosing accuracy
+ 5° to + 50° C
215 mm
190 mm
60 mm
1000 Kg
RS 232C optional
100÷240V 50÷60 Hz 12VA
For all metals, steel, hard steel, cast iron,
Nitriding, cementation, hard facing with
brass, aluminium over 0.6mm, plastics, soft
depth less to 0.6 mm
and hard rubber
65 kg
85 kg
37x60x102 cm
*
AFFRI
ROCKWELL, BRINELL
How to use:
Acting the hand wheel on the base will be performed indenter approach to the test block and in few
seconds the result will appear.
Force:
the test force is selected and applied through load cell inside directly connected to the indenter axis and
closed loop control inside. Accuracy conforms to ISO-JIS standards.
Performance: it can be utilised by everybody in a simple action
- no need to be levelled when installed
- can work also near to vibration
250 DRM
Technical characteristics (code 1503)
Preload
(10 Kgf) 98.07 N - (3 Kgf) 29.4 N
Vickers Knoop loads
(3 5 10 15 20 30 60 100 Kgf)
29.43 49.05 98.1 147.15 196 294.3 588.6 981 N
Rockwell loads
SuperRockwell loads
(10 60 100 150 Kgf) 98.10 588.60 981 1471.50 N
(3 15 30 45 Kgf) 29.43 147.15 294.30 441.45 N
Brinell loads
(5 6.25 10 15.6 25 30 31.2 62.5 125 187.5 Kgf)
49.05 61.3 98.1 153.23 245 294.43 306.5 613 1226 1839 N
Mode of operation
automatic with load cell and closed loop Affri patent
Feasible tests
Twin
Rockwell HRC A D B F G L M R
Superficial Rockwell HRN+HRT
Brinell HB 30, HB 10, HB 5, HB 2.5; Break Nmm2
Vickers (3 5 10 20 30 50 100 Kgf) 29.43 49.05 98.10 196.20 294.30 490.50 981 N only indentation
Digital reading
Accuracy
Operativity
Temperature range
Total height capacity
Total depth capacity
Max load of test piece
Data output
Power supply
Fields of application
Net weight
Packing weight
Packing measurements
206 MX / 206 MXS
Rockwell - Brinell - Vickers - Resolution: 0.1 HR - 0.1HB - 0.1 HV (0.01 HR unit, at request)
Conformation standards EN-ISO 6506-2 / 6507-2 / 6508-2 / ASTM-E18 / JIS
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
+ 5° to + 50° C
215 mm
190 mm
1000 Kg
RS 232 C
220V 50÷60Hz - 200VA
For all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing
75 Kg
90 Kg
37x60x100 cm
Technical characteristics: 206 MX (code 1116)
206 MXS (code 1117)
Preload
(10 Kgf) 98.07 N
29.4N (3 Kgf)
Test Load
588-980-1471N Rockwell (60-100-150Kgf)
98.07-588N Vickers (10-60Kgf)
147-294-441N Superficial Rockwell (15-30-45Kgf)
29-147-294N Vickers (3-15-30Kgf)
Mode of operation
Feasible Tests
Twin
Reading resolution
Accuracy
Operativity
Temperature range
Height capacity
Depth capacity
Diameter of anvil
Max load of test piece
Data output
Power supply
Fields of application
Net weight
Packing weight
Packing measurements
Motorized load application - Electronic control
Motorized load application - Electronic control
Rockwell:
Superficial Rockwell:
HRA; HRB; HRC; HRD; HRE; HRF; HRG; HRH; HRK HR15N; HR30N; HR45N; HR15T; HR30T; HR45T
Vickers: HV10; HV60; HV100 only indentation
Vickers: HV3; HV15; Hv30
Brinell (on request):
Brinell (on request):
HB 2.5/62.5; HB2.5/187.5; HB 5/125
HB 2.5/15.625; HB 2.5/31.25
HBT 2.5/62.5; HBT 2.5/187.5; HBT 5/125
HBT 2.5/15.625; HBT 2.5/31.25
0.1 HR - 0.1 HB
0.2 HR - 0.2 HB
Conformation standards EN-ISO 6508-2 / 6506-2 / JIS
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
+ 5° to + 50° C
215 mm
190 mm
60 mm
1000 Kg
RS 232 C optional
100÷240V 50÷60 Hz 12VA
For all metals, steel, hard steel, cast iron,
Nitriding, cementation, hard facing with depth
brass, aluminium over 0.6mm, plastics, soft
less to 0.6 mm
and hard rubber
65 kg
85 kg
37x60x102 cm
*
*
13
®
AFFRI
®
PORTABLES
HARD TEST-I
Conform with standard DIN 50157
A new combined tester for Hardness and sigma break tests in one instrument: quick and accurate for production departments
without requiring laboratory inspection.
DIRECT DIGITAL READOUT ON 10 HARDNESS SCALES
QUICK: in only 2 seconds the hardness and sigma are measured on large range of metallic products
UNIVERSAL: designed to check sheets, metal rolls, shaped parts, tubes, on aluminium, brass, copper and steel
ACCURATE: products and surfaces down to 0.08 mm thick can be checked. It works using the innovative Affri system which measures the real indentation depth
applying constant incremental load rates through a minor and major load ( as in laboratory machines).
14
AFFRI
PORTABLES
HARD TEST-II
Conform with standard DIN 50157
Cod. 23631 handwheel for Metaltester.
Automatic clamping and testing cycle for metals parts.
Capacity 30x30 mm.
For fast accurate hardness on production department.
METALTESTER MKII
-
Conform with standard DIN 50157
For every kind of metal both very hard and soft
Suitable for flat, round and irregular pieces
No need to adjust it
Accuracy ± 0.5 HRC
For thin surfaces: up to 0.08 mm thickness and large parts
Technical characteristics
Min. thickness measurable
Principle of operation
Fields of application
Mod 2102= 0.08mm Mod 2102/2=0.06 mm at 65HRC
Load with electronic control
for all metals
Digital scale read out
(other scales on request)
Rockwell HRA (20...92); HRB (26...100); HRC (0...80);
HR15N (69...93); HR30T (16...83)
Brinell HB5 (5.. .205); HB30 (66...884) Knoop (25...97)
Vickers (13...1865)
Tensile Module R (226.. .2898) HZA (0...250)
Webster B 0 – 20 (on request)
Barcol 0 – 100 (on request)
Display resolution
Repeatability
Memory of test results
Data transmission
Statistic of results
Display
0.1 Unit
± 0.5% on reference test block HRC
500 tests
RS 232 C
mean of resulfs
LCD
Printer (option)
20 column termic paper
measures: (15 x 10 x 4 cm)
Power supply
Operating time
Automatic shut off
Dimension of probe
Dimension of electronic box
Weight
Dimension of case
rechargeable battery 6V
1000 tests
After a pause of 2 minutes. Restart by button
body: ø 40 mm x 90 mm - base ø 20 min.
160 x 90 x 50h mm
300 gr. probe - 980 gr. digital box - 2.5 Kg with case
30x20x15 cm
Interchangeable
test heads are
designed for a
wide range of
metal applications
and surfaces.
Test on
small area
15
®
AFFRI
PORTABLES
®
METALTEST
Conform with standard DIN 50157
Portable hardness tester compact and easy to use in every position with immediate result on HRC, HRB, HRA, HB, HV, Nmm2, HR 15N units
No limit on thickness can be tested, thin materials as coating surface of 0.08 mm can be accurately measured.
- For every kind of metal both very hard and soft
- Suitable for flat, round and irregular pieces
- No need for adjustment if used inclined or inverted
- No affected by thickness of sample
- For thin surfaces: down to 0.08 mm thickness and large parts
- 10 different scales on the display
- Memory of the results 100 values (each scale)
- Average of the stored results.
- Repeatability + / - 0,5 HR on test block
Applicable accessories for all portables models:
Optional: Art. 2315
For irregular surfaces
Coils
Optional: Art. 2316 V long base
Easy test on long screws
MICROTESTER
Conform with standard DIN 50157
Applicable electronic processor:
Large LCD display and user friendly keypad make the
microtester easy to operate
Advanced graphic LCD and
software multifunctions
Bench instrument
Cod. 2312 including anvils for 2102 is
ideal for testing small samples
16
AFFRI
PORTABLES
EDA300
Motorized stand for MKII
- Conform with standard DIN 50157
- Accurate rapid and reproduceable results from mesurement of penetration depth and low constant force the most repatable instrument in the
world + / - 0,5 HRC
- Direct reasult in 10 different hardness scales and N mm2 sigma range to measure from 10 HRB to 1800 HV
- A single start input to activate without interruption phase: move down head indenter to take the conatct with test surface, clamp sample and
execute the test and goes back
- A test is perfomed in only 3 seconds independently from every distance of test sample
Technical characteristics
Total height capacity
Minimum thickness measurable
Ø measurable
Total depth capacity
from 0 to 170 mm
0.08 mm 600 Vickers
from 0.5 mm to 150 mm
75 mm
17
®
AFFRI
PORTABLES
®
HT-1000 / HT-2000
Extension probe Ø4 mm
Printer is included
on HT-2000
Portable rebound hardness tester with
data output to send data to the printer
for all metals.
Direct digital readout on crystal liquid display in the following scales: HV HRC HRB HB HL
or HSD. It work on all metals, very rapid and easy to use with only a touch of
the button.
SPECIFICATION:
Display: 4 digit LCD with switch able backlight
Calendar, data, hour programmable
Inclination of probe programmable
Statistic, visible on display and printable.
MEASUREMENT RANGE:
Leeb: 50 to 1000 HL
Shore: 32.5 to 99.5HS
Brinell 45 to 700HB
Vickers: 32 to 900HV
Rockwell C: 20 to 68.8 HRC
Rockwell B : 4 to 100 HRB
Power supply: AA 1.5V x 2 Batteries
Weight: Approx 100g
Operating temp: 10°C to 50°C
Interface: Infrared for printer and computer
HT-1000 PACKAGE INCLUDES:
- HT-1000 hardness Tester
- Standard Test Block
- Support Ring .79” (20 mm)
- Support Ring .53” (13 mm)
- Plastic Carrying Case
- Tube Cleaning Brush
- CR-2330 Lithium Batteries (2)
- Operating Manual
HT-2000 PACKAGE INCLUDES:
- HT-2000 hardness Tester + printer infrared
- Standard Test Block
- Support Ring .79” (20 mm)
- Support Ring .53” (13 mm)
- HP 82240B Infrared Printer
- CR-2330 Lithium Batteriers (2)
- 1.5V AA Alkaline Batteriers (4)
- Plastic Carrying Case
- Tube Cleaning Brush
- Operating Manual
OPTIONAL ACCESSORIES:
- extension probe Ø4 mm, L=50 mm
- set of rings for various surface round
Caratteristiche tecniche:
Calendar, data, hour programmable (only for HT2000), Inclination of probe programmable, Statistic, visible on display and printable
Display
4 digit LCD with switchable backlight
Measurement Range
Leeb: 50 to 1000 HL
Shore: 30 to 100 HS
Brinell: 75 to 700 HB
Vickers: 75 to 1000 HV
Rockwell C: 20 to 70 HRC
Rockwell B: 35 to 100 HRB
Scales
HL, HV, HB, HRC, HSD, HRB
Accuracy
+/- 4 HL
Testing direction
Vertically / Down / 45° Down / Horizontal
Materials
Low carbon steel, High alloy steel
Operating Temperature
Operating: 10 °C to 40 °C
Storage: - 20 °C to 50 °C
Power supply
AA 1.5V x 2 batteries
Batteries
Tester: Two, 3V Lithium CR2330 batteries
Printer: Four, 1.5V Alkaline AA batteries
Battery life
Tester: Work Life 40 hours continuous (2.500 test results) - Shelf Life 2 Year
Printer
6.000 print lines infrared (only for HT2000)
Data Storage
Automatic recording up to 200 test results including readings, conversions, average values, hardness scale, material, direction, date and time.
Time and date
Real time and date with a 10 year calendar
Interface
infrared for printer and computer (only for HT2000)
Tester dimensions
165x28x28 mm
Contact Dia.
20 and 13.5 mm
Weight
120 gr
18
AFFRI
MICRO VICKERS
DM8
Very large colour touch screen with integrated
functions.
The most complete system in the world. Multi
objective and multi indenters.
Ideal for factory and laboratory use.
It indicates load force applied, load time, Diagonal
1 and Diagonal 2, hardness results, number of
measurements stored, averages, statistics.
Self conversion data. HV and HK Knoop test can
be calculated just by selecting switch and applying
extra Knoop indenter.
Autoturret multi step 3 or 6 positions to install
till to 4 objectives and + 2 indenters
Technical characteristics (code 7101)
DM-8 A and B
Auto-turret
2 Indenters + 4 Objectives
Max. height of specimen
120 mm
Max. depth of specimen
160 mm
Reading
Digital - Touch panel
mN
49.03 98.07 245.2 490.3 980.7 1961
DM-8A
(gf)
5
10
25
50 100 200
mN 9.807 29.42 49.03 98.07 245.2 490.3 980.7 1961 2942
DM-8B
(gf)
1
3
5
10 25
50 100 200 300
2942
300
4903
500
Measuring
microscope
Max. measuring length
Min. graduation
Min. measuring unit
Loading mechanism
Load applying speed
Dwell time
LCD type touch panel
256 data memory
Hardness conversion
OK/NG criteria
Data editing
Data output
Accuracy
Photographic device
Dimensions
Weight
Power supply
Automatic loading and releasing method
50 µm/sec
5~60 sec
Yes
Yes
Possible in compliance with ASTM (E-140),JIS
Yes
Yes
RS232C
According to ASTM E-384, ISO 6507-2 and JIS B 7734
Possible to mount at anytime (camera sleeve:optional)
Main body only: W220xD400xH500
28 kg
Single phase AC100~240V 50/60Hz available
4903 9807
500 1000
9807 19614
1000 2000
250 µm
0.01 µm
0.01 µm
19
®
AFFRI
DM2
MICRO VICKERS
®
CCD camera transmits the image to the computer and
EASYDUR® Software for fast and automatic Vickers
measurements it eliminates human errors, saves
data, performs statistics, prints out results (optional).
Auto turret to select indenter
and objective.
Software for quick or automatic
Vickers measure (optional)
Control panel integrated with
ergonomic touch key board.
2 digital large LED indicate load force
applied, Load time, Diagonal 1 and
Diagonal 2, Hardness results, number
of measurements stored, average,
statistics. HV and HK (Knoop test can
be calculated just by selecting switch
and applying extra Knoop indenter).
STANDARD ACCESSORIES
- Manual X-Y table 100x100mm,
range 25x25 mm div 0.01 mm
- Precision vice 15 mm
- Test block HV 700
- Test block HV 400
- Diamond indenter for HV
- Measuring microscope electronic type
- Measuring microscope mechanical type
Case depth diagram
-
Object lens (Built in) x10
Object lens (Built in) x40
Level adjusting leg
Light source bulb (12V 18W)
Auxiliary tools
Instruction manual
Accessories box
Automatic conversion: Vickers - Rockckwell
Technical characteristics
Test load
( mN ) N
( gf ) Symbol
Dwell time
Measuring microscope
Read out
Data output
Magnification
Max. height of specimen
Max. depth of specimen
Dimensions main body only
Weight
Load applying speed
Auto-turret
Loading mechanism
Accuracy
Photographic device
Power supply
20
Max. measuring length
Min. graduation
Min. measuring unit
DM-2 A
DM-2 D
( 98.07 245.2 490.3 980.7 1961 2942 4903 9807 )
( 10
25
50 100 200 300 500 1000 )
5~40sec.
5~60 sec
250 µm
0.5 µm
0.1 HV
250 µm
0.1 µm
0.1 HV
Analogic
-
Digital
Centronics
100x - 400x
95 mm
100 mm
W220xD400xH500 mm
28 kg
50 µm/sec
Yes
Automatic loading and releasing method
According to JIS B 7734 and ASTM E-384 / JIS
Possible to mount at anytime (camera sleeve:optional)
Single phase AC100~240V 50/60Hz available
OPTIONAL
- Knoop indenter
- Knoop test block
- Printer
- Motorized X-Y table
- Software Semi Auto for easy Vickers measure
- X-Y table motorized, programmable step
- Software AUTO for automatic Vickers measure
- Digital micrometer div 0.001 mm TESA
AFFRI
MICRO VICKERS
DM2 AUTO
DM8 AUTO
Multi sample function
DM8 AUTO
X-Y table action with joystick
Multiple Samples Holder
sample holders have unique design, allowing users to analyze mounted or un mounted samples.
Holding multiple samples, some holders accommodate a test block, allowing users to validate the
calibration of the micro hardness tester at any time without to remove the sample. The samples
can be remove easily or inserted with a simple slide-in drawer system.
Example of scanning area
DM8 AUTO - DM2 AUTO includes: X-Y-Z axis auto focus fully motorized and camera, software
to manage the cycle and auto-measure, table area 100x100mm or 200x90 mm, with excellent
accuracy 1 µm;
Mosaic Feature
DM8 AUTO is the first hardness tester to offer a complete, high definition image of a sample,
no matter its size. This innovative feature provides an “aerial view” of the sample, offering sharp
close-ups as well as global views. The Mosaic Image makes it possible to position as many as
99 traverses – to within a few micron
Traverse positioned in the middle of the branch and paralleled to the edge
21
®
AFFRI
VICKERS DIGITAL MOTORIZED
®
DM5
CCCD camera for vision of indentations
and connection to PC and software for
automatic Vickers measure
Software Taurus: Automatic Vickers measure, store data, create case depth diagram, test report
Easy and simple action.
STANDARD ACCESSORIES
- 136° Vickers indenter
- HV test block
- Anvil flat 50 mm
- V face anvil 50 mm
- Spare bulb
- Eyepiece 10x
- Obiective 10x
- User’s manual
- Cable cord
- Certificate of calibration
OPTIONAL ACCESSORIES
n. 1 Motorized turret for DM5A
n. 1 Objective 20x (for DM5A only)
n. 1 X - Y table 100 x 100 mm 25 x 25 mm travel 0.01 mm division
n. 1 Software Taurus for automatic Vickers measure and case depth diagram
n. 1 CCD camera adapter
n. 1 Vice 25 mm capacity.
Fast selection of test load trough knob
Digital display of load, dwell time, Vickers result, number of test
conversion result to Rockwell, Brinell scale
Conform to the ISO 6507.2 , ASTM E 384 JISB 7734
Automatic turret to select indenter and objective
Technical data
Test loads
Digital Display
Out data
Objective
Magnifications
Field of vision
Division
Switch objective/indenter
Eyepiece
Table
Camera connection
Height capacity
Depth capacity
Digital display
Digital display
Digital display
Light
Power source
Weight
Dimension
22
DM-5 A
DM-5 B
0.3 0.5 1 3 5 10 20 30
1 2 3 5 10 20 30 50
Vickers, Brinell, Rockwell C
RS32 C
10x
10x - 20x
100x
100x - 200x
900µm (100x)
900µm (100x); 450 µm (200x)
0.5µm (100x)
0.5µm (100x); 0.1 µm (200x)
manual turret
manual turret (option motorized)
digital encoder 10x
X - Y 100x100 travel 25x25 division 0.01 mm
special adaptor optional
max 210 mm w. flat anvil
160 mm
of programmed load
dwell time 1 to 99 sec. programmable
No. of tests
adjustable by key board
220 240 V single phase
55 Kg
55 x 30 x 700H cm
Turret to self switch in indenter objective
(2 obiectives for DM5A 1 objective for DM5B)
MOTORIZED X-Y TABLE connected with CNC computer for
automatic tests
AFFRI
ROCKWELL, BRINELL, VICKERS, KNOOP, ISO 2039, SHORE
INTEGRAL 6
➁ Motorized turret at 5 - 3 - 2 steps
self switch indenter – objectives
- Fully Automatic Universal Hardnss Tester
- Automatic Rockwell, Brinell, Vickers, Knoop,
ISO 2039, SHORE measures
- Thanks to the Affri system Closed loop technologies
inside the Autofocus for Vickers and Brinell is easy
and automatic
- Color touch screen TFT 17” inclinable 180°
- Large base for heavy parts 400 x 400 mm
- Sliding indenter stroke from 300 to 0 mm self
touching surface
- Automatic clamping for Rockwell tests (Brinell at
request)
- One single start input to activate without interruption:
(self touch surface to be tested, self load -un-load
self switching indenter, optic, self focus and self
measure,self goes up to free sample)
- The first test is valid, non need to repeat. Absolute
measure
- Insensible to external vibrations sources
- Insensible to deflections during test cycle
- Insensible to change of temperature ( 5 to + 50°C)
- It can be operative also if is not leveled or if inclined
OPTION
- Clamping system combinet to the high technology of
Affri System assure perfect clamping also on unstable or flexible parts
- Rotating turret at 6 positions for automatic switch to
several indenters and objectives ➁
- Motorized X-Y axis table 200 x 100mm division
0.01 mm combined to automatic start test cycle for
hardness case depth. The axis are independently or
combined programmed ➂.
- Large vision filed optic camera for automatic sample
border or bar code recognizing
- Martens hardness cicle
➂ Motorized X Y table for series of Vickers
test and auto recognize zero point
Automatic Vickers measure
Automatic check-up correct objective
and indenter installed on
Complete statistic and test report
on Excel® format
Martens hardness
Available models Rockwell, Brinell, VICKERS, KnOop, ISO 2039, SHORE
- INTEGRAL 6 (loads from 0.3 to 30) Micro Vickers + Superficial Rockwell + Brinell
Micro Vickers - Knoop 0.3 0.5 1 2 5 10 20 30 kgf (2,94 4,9 9,81 19,6 49,05 98,1 196 294,3 N)
Superficial Rockwell 15 30 45 kgf (147 294 441,45 N)
Shore A B C D O OO
Brinell 1 5 10 30 31.2 kgf (9,81 49,05 98,1 294 306 N)
ISO 2039
Martens max 30 kgf (294 N)
Technical characteristics
Measures
Automatic Brinell - Vickers / Rockwell / Knoop / ISO 2039 / SHORE
Automatic
Focus
HDTL function
Permits checking the case depth of hardness treathment from 0.15 to 1.5 mm at 525 - 550 - 600 HV1
Test height
max 300 min 0 mm self adjusting acting the Test start input
Depth
170 mm (other on request)
Action: Only one start input moves down head and indenter to take test surface contact, self load -un-load self switching indenter, optic, self focus and self measure,self goes up to free sample
Load forces
controlled by internal load cell and closed loop Affri system patent
Automatic turret
self switching 1 indenter + 1 objective (optional 5 steps 3 indenters + 2 objectives)
Resolution
0.1 HB / 0.1 HR / 0.1 HV / 0.1 HK / 0.1 SH
Net work
wire connection for technical assistance auto diagnosis
Knoop ISO 4545
Brinell
EN-ISO 6506-2
Rockwell EN-ISO 6508-2
Accuracy: Conformation standards
Vickers EN-ISO 6507-2
Plastic DIN EN 53456, EN-ISO 2039-2
Shore A B C D O OO ISO 7619 - ISO 868
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
from 0 to 300 mm
Self aligning to test surface
Max. weight allowed for the specimen to be tested 2000 Kg
400x400 mm
Base
Fields of application
For all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastic
Size
600x400x800h
Net weight
150 Kg
Packing weight
200 Kg
Power supply
220V 50÷60Hz - 200VA - Air compressed 5 ATM
JIS
23
®
AFFRI
UNIVERSAL ROCKWELL, BRINELL, VICKERS
®
INTEGRAL
Automatic Vickers measure
Automatic check-up correct objective
and indenter installed on
➀ Clamping system for long parts
Complete statistic and test report
on Excel® format
➁ Motorized turret at 5 - 3 - 2 steps
self switch indenter – objectives
➃ Automatic case depth measurement
without cut the sample HDTL principle
➂ Motorized X Y table for
series of Vickers test and auto
recognize zero point
- Fully Automatic Universal Hardnss Tester
- Automatic Brinell, Vickers, Rockwell measures
- Thanks to the Affri system Closed loop technologies inside the Autofocus for Vickers and Brinell is
easy and automatic
- It can measures automatically the case depth surface of heat treatment from 0.15 to 1.5 mm thickness directly up the surface without cutting the
sample (HDTL) cycle. It is not a destructive test.
- Color touch screen TFT 17” inclinable 180°
- Large base for heavy parts 400 x 400 mm
- Sliding indenter stroke from 500 to 0 mm self
touching surface
- Automatic clamping for Rockwell tests (Brinell at
request)
- One single start input to activate without interruption: (self touch surface to be tested, self load -unload self switching indenter, optic, self focus and
self measure,self goes up to free sample)
- The first test is valid, non need to repeat. Absolute
measure
- Insensible to external vibrations sources
- Insensible to deflections during test cycle
- Insensible to change of temperature ( 5 to + 50°C)
- It can be operative also if is not leveled or if inclined
OPTION
- Clamping system combinet to the high technology
of Affri System assure perfect clamping also on
unstable or flexible parts ➀
- Rotating turret at 6 positions for automatic switch to
several indenters and objectives ➁
- Motorized X-Y axis table 200 x 100mm division
0.01 mm combined to automatic start test cycle
for hardness case depth. The axis are independently or combined programmed ➂.
- Large vision filed optic camera for automatic sample border or bar code recognizing.
- HDTL for case depht ➃.
Available models
- INTEGRAL 1 (loads from 15.6 to 3000) Brinell
- INTEGRAL 4 (loads from 1 to 50) Brinell + Vickers + Shore
Brinell 15.6 31.2 62.5 125 187.5 250 500 750 1000 3000.
Brinell 1 5 10 30 31.2 50, Vickers 1 2 3 5 10 15 30 50, Rockwell 15N/T 30N/T 45N/T
ISO 2039 tests for plastic
- INTEGRAL 2 (loads from 1 to 250) Rockwell+Brinell + Vickers + Shore
Brinell 1 5 10 15 15.6 30 31.2 62.5 125 187.5 250 .
- INTEGRAL 5 (loads from 10 to 3000) Rockwell + Brinell + Vickers
Vickers 1 2 3 5 10 15 30 50 60 100
Brinell 10 30 31.2 62.5 125 187.5 250 500 750 1000 3000.
Rockwell 15N/T 30N/T 45N/T 60 100 150 HRC A D B F G L M R S T V X Z
Vickers 10 15 30 50 60 100 120
ISO 2039 tests for plastic
Rockwell 60 100 150 HRC A D B F G L M R S T V X Z
HDTL case depth test
- INTEGRAL 3 (loads from 3 to 1000) Brinell + Vickers + Rockwell +Superficial
Rockwell + Case depth
- INTEGRAL 6 (loads from 0.3 to 30) Micro Vickers + Superficial Rockwell + Brinell
Brinell: 3 5 10 15.5 31.2 62.5 125 187.5 250 500 1000; Vickers: 3 5 10 15 30 60 100 120
Micro Vickers 0.3 0.5 1 2 5 10 20 30, Brinell 1 5 10 30 31.2, Superficial Rockwell 15 30 45
Rockwell: 60 100 150; Superficial Rockwell: 15 30 45
HDTL case depth automatic HV 525 - 550 – 600 (at request)
Technical characteristics
Measures
Automatic Brinell, Vickers, Rockwell and case depth treatment (depend to the models)
Automatic
Focus
HDTL function
Permits checking the case depth of hardness treathment from 0.15 to 1.5 mm at 525 - 550 - 600 HV1
Test height
max 500 min 50 mm self adjusting acting the Test start input
Depth
170 mm (other on request)
Action: Only one start input moves down head and indenter to reach test surface self touch surface to be tested, self load -un-load self switching indenter, optic, self focus and self measure,self goes up to free sample
controlled by internal load cell and closed loop Affri system patent
Load forces
Automatic turret
self switching 1 indenter + 1 objective (optional 5 steps 3 indenters + 2 objectives)
Resolution
0.1 unit (0.01 mm case depth)
Net work
wire connection for technical assistance auto diagnosis
Plastic DIN EN 53456, EN-ISO 2039-2
Brinell
EN-ISO 6506-2
Knoop
Accuracy: Conformation standards
Vickers EN-ISO 6507-2
Rockwell EN-ISO 6508-2
JIS
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
from 0 to 500 mm
Self aligning to test surface
Max. weight allowed for the specimen to be tested 2000 Kg
400x400 mm
Base
Fields of application
For all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastic
Size
600x1000x1800h
Net weight
500 Kg
Packing weight
600 Kg
Power supply
220V 50÷60Hz - 200VA - Air compressed 5 ATM
24
AFFRI
UNIVERSAL ROCKWELL, BRINELL, VICKERS
INTEGRAL - E
Automatic Vickers measure
➁ Motorized turret at 5 - 3 - 2 steps
self switch indenter – objectives
Automatic check-up correct objective
and indenter installed on
- Fully Automatic Universal Hardness Tester
- It can measures automatically the case depth surface of heat treatment from 0.15 to 1.5 mm thickness directly up the surface without
cutting sample (HDTL) cycle. It is not a destructive test.
- Automatic Brinell, Vickers, Rockwell measures
- Thanks to the Affri system Closed loop technologies inside the
Autofocus for Vickers and Brinell is easy and automatic
- Color touch screen TFT 17”
- Elevating screw columns base for fast adjustments
- Sliding indenter stroke from 50 to 0 mm self touching surface
- Automatic clamping for Rockwell tests (Brinell at request)
- One single start input to activate without interruption: (self touch surface to be tested, self load -un-load self switching indenter, optic,
self focus and self measure,self goes up to free sample)
- The first test is valid, non need to repeat. Absolute measure
- Insensible to external vibrations sources
- Insensible to change of temperature ( 5 to + 50°C)
- Insensible to deflections during test cycle
- It can be operative also if is not leveled or if inclined
Exampe of test report for case depth:
TEST REPORT
Test report for
AFFRI - HDTL
case depth HDTL
Hardness Depth Treatment Loads
measurement
Product Code
............
Operator
............ Date of test
............ Vickers
depth measured
HV 525
0.27 mm
HV 550
0.31 mm
HV 600
0.34 mm
Superficial Hardness detected HRC 54.46
Complete statistic and test report
on Excel® format
➀ Automatic case depth measurement
without cut the sample HDTL principle
OPTION
- Clamping system combinet to the high technology of Affri System
assure perfect clamping also on unstable or flexible parts ➀
- Rotating turret at 6 positions for automatic switch to several indenters and objectives ➁
- Motorized X-Y axis table 200 x 100mm division 0.01 mm combined
to automatic start test cycle for hardness case depth. The axis are
independently or combined programmed ➂.
- Large vision filed optic camera for automatic sample border or bar
code recognizing.
- HDTL for case depht ➃.
Available models
- INTEGRAL - E 1 (loads from 15.6 to 3000) Brinell
- INTEGRAL - E 4 (loads from 1 to 50) Brinell + Vickers + Shore
Brinell 15.6 31.2 62.5 125 187.5 250 500 750 1000 3000.
Brinell 1 5 10 30 31.2 50, Vickers 1 2 3 5 10 15 30 50, Rockwell 15N/T 30N/T 45N/T
ISO 2039 tests for plastic
- INTEGRAL - E 2 (loads from 1 to 250) Rockwell+Brinell + Vickers + Shore
Brinell 1 5 10 15 15.6 30 31.2 62.5 125 187.5 250 .
- INTEGRAL - E 5 (loads from 10 to 3000) Rockwell + Brinell + Vickers
Vickers 1 2 3 5 10 15 30 50 60 100
Brinell 10 30 31.2 62.5 125 187.5 250 500 750 1000 3000.
Rockwell 15N/T 30N/T 45N/T 60 100 150 HRC A D B F G L M R S T V X Z
Vickers 10 15 30 50 60 100 120
ISO 2039 tests for plastic
Rockwell 60 100 150 HRC A D B F G L M R S T V X Z
HDTL case depth test
- INTEGRAL - E 3 (loads from 3 to 1000) Brinell + Vickers + Rockwell +Superficial
Rockwell + Case depth
- INTEGRAL - E 6 (loads from 0.3 to 30) Micro Vickers+Superficial Rockwell+Brinell
Micro Vickers 0.3 0.5 1 2 5 10 20 30
Brinell: 3 5 10 15.5 31.2 62.5 125 187.5 250 500 1000; Vickers: 3 5 10 15 30 60 100 120
Brinell 1 5 10 30 31.2
Rockwell: 60 100 150; Superficial Rockwell: 15 30 45
Superficial Rockwell 15 30 45
HDTL case depth automatic HV 525 - 550 – 600 (at request)
Technical characteristics
Measures
Automatic Brinell, Vickers, Rockwell and case depth treatment (depend to the models)
Resolution
0.1 HR 0.01 mm case depth
HDTL function
Permits checking the case depth of hardness from 0.15 to 1.5 mm range at 525 - 550 - 600 HV1
Load force
Controlled in closed loop load cell inside Affri patent
Test height
max 400 min 0 mm self adjusting in step of 50 mm acting the Test start input and Handweel for long stroke
200 mm (others on request)
Depth
Action: Only one start input moves down head and indenter to reach test surface self touch surface to be tested, self load -un-load self switching indenter, optic, self focus and self measure,self goes up to free sample
Automatic turret
self switching 1 indenter + 1 objective (optional 5 steps 3 indenters + 2 objectives)
wire connection for technical assistance auto diagnosis
Net work
Operativity
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Temperature range
+ 5° to + 50° C
from 0 to 50 mm
Self aligning to test surface
From 0 to 50 mm range
Compensation of deflection
Knoop
Rockwell EN-ISO 6508-2
Plastic DIN EN 53456, EN-ISO 2039-2
JIS
Accuracy: Conformation standards
Brinell EN-ISO 6506-2
Vickers EN-ISO 6507-2
Max. weight allowed for the specimen to be tested
Base
Fields of application
Size
Net weight
Packing weight
Power supply
200 Kg
Anvils set applicables
For all metals: iron, steel, tempered steel, brass, aluminium and nitriding, cementation, hard facing, plastic
400x600x1700h
380 Kg
450 Kg
220V 50÷60Hz - 200VA - Air compressed 5 ATM
25
®
AFFRI
®
270 VRSD
270 VRSA
UNIVERSAL ROCKWELL, BRINELL, VICKERS
770 VRSD
Fully motorized up/down head
from 0 to 700 mm
270 VRSTV
Optional screen combined
with camera and software
Semi auto or auto measure
VRSA
Digital reading
through data
entering
ALL OPERATIONS ARE MANAGED
BY A SINGLE DRIVE INCLUDING AUTOMATIC
RESEARCH OF TEST PIECE
- Pushing the Start button, head moves down to reach the test surface from
distance multiples of 50 mm and automatically starts the hardness test cycle in
automatic succession without breaking a phase:
- approach to the piece;
- clamping of the piece;
- activation of reference surface;
- entire test cycle performance and release of piece.
Sleading table (optional)
cod. 13601 large anvil V face
Clamping base for big or
unstable pieces (optional)
Technical characteristics
270 VRSTV VM VICKERS (code 6112)
270 VRSD VM VICKERS (code 6111)
270 VRSA VM VICKERS (code 6110)
Vickers force
(0.3 0.5 1 2 2.5 3 5 10 15 20 30 50 Kgf) 2.94 4.9 9.81 19.6 24.5 29.43 49.05 98.1 147.15 196 294.3 490 N
Super Rockwell force 15 30 45 HRN - HRT
270 VRSTV (code 6102)
270 VRSD (code 6101)
270 VRSA (code 6100)
Vickers Knoop loads (1 2 2.5 3 5 10 15 20 30 60 100 Kgf) 9.81 19.6 24.5 29.43 49.05 98.1 147.15 196 294.3 588.6 981 N
(10 60 100 150 Kgf) 98.10 588.60 981 1471.50 N
Rockwell loads
SuperRockwell loads (3 15 30 45 Kgf) 29.43 147.15 294.30 441.45 N
(5 6.25 10 15.6 25 30 31.2 62.5 125 187.5 Kgf - on request extra 250 Kgf) 49.05 61.3 98.1 153.23 245 294.43 306.5 613 1226 1839 N (on request 2452)
Brinell loads
49 132 358 961 N (for plastic, rubber as per EN-ISO 2039 std) (250 Kgf) 2452.5 N Brinell
Optional test loads
Shore
A-B-C-D
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
Temperature range + 5° to + 50° C
Self aligning to test surface from 0 to 400 mm
Fix cup optional
Clamping
Action: only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and automatically starts the hardness cycle in automatic succession without breaking a phase
from 0 to 50 mm multiple till 400 mm
Mobile Indenter
from 0 to 50 mm multiple till 400 mm
Mobile clamping
75x 150x 225x 300x
Magnification
Automatic compensation of deflection piece from 0 to 50 mm
0.1 HR-HB-HV ( 0.01 HR unit, at request) - (0.1 micron mm) Vickers Brinell
Reading resolution
Digital encoder for Brinell - Vickers
Reading
Drum scale + digital readout
CCD camera + computer
Total depth capacity 190 mm
270x330 mm
Working table
375 mm (700 mm for model 770 VRSD fully motorized)
Working height
Max. weight allowed for the specimen to be tested: 2000 Kg
RS 232 C
Data output
220V 50÷60Hz - 200VA
Power supply
95 Kg (150 Kg for 770 VRSD)
Net weight
120 Kg (190 Kg for 770 VRSD)
Packing weight
80x80x150 cm
Packing measure
CCD camera
High resolution, Vickers semi auto / Auto measure
26
AFFRI
UNIVERSAL ROCKWELL, BRINELL, VICKERS
251 VRSD / 251 VRSA
251 VRSTV
Optional screen combined
with camera and software
Software and camera for quick
Vickers and Brinell measures
Auto measurements (optional)
Clamping base for big or
unstable pieces (optional)
ALL OPERATIONS ARE MANAGED BY A SINGLE DRIVE INCLUDING AUTOMATIC RESEARCH OF TEST PIECE
Pushing the Start button, head moves down to reach the test surface from distance multiples of 50 mm and automatically starts the hardness test cycle in
automatic succession without breaking a phase:
- approach to the piece; - activation of reference surface; - clamping of the piece; - entire test cycle performance and release of piece.
Technical characteristics
Vickers force
Super Rockwell force
251 VRSD VM VICKERS (code 6212)
(0.3 0.5 1 2 2.5 3 5 10 15 20 30 50 Kgf)
15 30 45 HRN - HRT
Vickers Knoop loads
Rockwell loads
SuperRockwell loads
251 VRSD (code 6202)
251 VRSA (code 6201)
251 VRSTV (code 6203)
(1 2 2.5 3 5 10 15 20 30 60 100 Kgf) 9.81 19.6 24.5 29.43 49.05 98.1 147.15 196 294.3 588.6 981 N
(10 60 100 150 Kgf) 98.10 588.60 981 1471.50 N
(3 15 30 45 Kgf) 29.43 147.15 294.30 441.45 N
Brinell loads
251 VRSA VM VICKERS (code 6211)
2.94 4.9 9.81 19.6 24.5 29.43 49.05 98.1 147.15 196 294.3 490 N
251 VRSTV VM VICKERS (code 6213)
(5 6.25 10 15.6 25 30 31.2 62.5 125 187.5 Kgf - on request extra 250 Kgf)
49.05 61.3 98.1 153.23 245 294.43 306.5 613 1226 1839 N (on request 2452)
49 132 358 961 N (for plastic, rubber as per EN-ISO 2039 std) (250 Kgf) 2452.5 N Brinell
Optional test loads
A-B-C-D
Shore
it can work if not levelled, inclined or near to vibration area, without loosing accuracy
Operativity
+ 5° to + 50° C
Temperature range
Self aligning to test surface from 0 to 50 mm
Clamping
Fix cup optional
Action: only one start input moves down head to reach and clamp the test surface from distance multiple of 50 mm and automatically starts the hardness cycle in automatic succession without breaking a phase
Mobile Indenter
from 0 to 50 mm
Mobile clamping
from 0 to 50 mm
Magnification
75x 150x 220x 300x
Automatic compensation of deflection piece from 0 to 50 mm
0.1 HR-HB-HV ( 0.01 HR unit, at request) - 0.1 micron mm
Reading resolution
Reading
Digital encoder for Brinell - Vickers
Drum scale + digital readout
CCD camera + computer
190 mm
Total depth capacity
200 mm
Working height
Data output
RS 232 C
220V 50÷60Hz - 200VA
Power supply
Net weight
75 Kg
95 Kg
Packing weight
Packing measurements 50x50x100 cms
CCD camera
High resolution, Vickers semi auto / Auto measure
27
®
AFFRI
®
UNIVERSAL ROCKWELL, BRINELL, VICKERS, KNOOP
LD 250
- A single initiation runs the automatic test cycle and presents the result.
- The LD 250 is a very practical and robust instrument designed to perform Vickers, Brinell, Rockwell, Super Rockwell
and Knoop Hardness tests conforming to the ISO 6506,6507,6508 and ISO 2039 standards
- Over the load range from 9.81N to 2452 N. The patented internal Affri system assures high performance automatic
load tests and automatic measurement on every scale
- Automatic selection of test load, indenter and objective plus automatic measurement cycle.
- Self start test load self switch indenter to objective self measure.
- High resolution video image via camera with auto adjustment of the iris to match the surface reflection and assure
perfect results on Vickers and Brinell measurements even if the surfaces are not highly polished.
- The test force is closed loop load control using an electronic load cell connected to the indenter eliminating friction
and error under all conditions.
- The ABSOLUTE control of loads assures infinite precision even in poor environments near sources of mechanical
vibration, or if the machine is not levelled or inclined and even if the test piece is not stable during the test.
- The first test is valid, non need to repeat. Absolute measure
- Automatic switching of indenter and objective
- One single start input to activate without interruption: (self touch surface to be tested, self load -un-load self switching
indenter, optic, self focus and self measure,self goes up to free sample)
- Touch screen colour TFT and full Windows system for easy use of the machine with information on a single screen
Technical data
Hardness scale
Vickers, Brinell, Rockwell, SuperRockwell, Knoop
Standard
Vickers ISO 6507, ASTM E 384,Rockwell ISO 6508, ASTM E 18, Knoop ISO 4545
Brinell ISO 6506, ASTM E 18, Rockwell for plastic ISO 2039, Shore ISO 7619 - ISO 868
Vickers loads
1 2 3 5 10 20 30 50 60 100 120
(9.81 19.6 29.43 49.05 98.1 196 294.3 490.5 588.6 981 1177.2 N)
Brinell loads
1 2.5 5 6.25 10 15 15.6 25 30 31.25 62.5 125 187.5 250
(9.81 24.5 49.05 61.3 98.1 147.15 153.23 245 294.3 306.5 613 1226 1839 2452 N)
15 30 45 (147.15 294.3 441.45 N)
Super Rockwelll loads
60 100 150 (588.60 981 1471.50 N)
Rockwelll loads
HBT 2,5 / 62,5 - 5 / 125 - 2,5/187,5
Automatic Brinell
Optics: real objective with predefined magnification. Pre-calibrated and combined with camera and video measurement software
Precision of the loads
0.1 %
Division on video measurements: 0.1 HB HV HRC HRN HK
Light source
Self adjusting with self iris
Indenters: Diamond Rockwell 120°, diamond Vicker 136°, diamond knoop 172°, ball 1/16”, 1/8”, ½” Rockwell, 1- 2,5 - 5 -10 mm W Brinell
(0,1 to 99,9 seconds) for minor and major load independently
Dwell time selectable
USB (RS 232C,LAN, wireless upon request)
Data transmission
300 mm (other on request)
Max capacity
160 mm (other on request)
Max depth
2000 KG
Max weight of test piece
220 240 V 50 60 Hz
Power supply
500 KG
Weight
28
Automatic
Brinell
measure
Automatic
Vickers
measure
Manual
Brinell, Vickers
and Knoop
measures
Complete
statistic and
test report
on Excel®
format
Automatic
check-up
correct
objective and
indenter
installed on
Scrolling menu on
touch screen
fast and easy use
AFFRI
UNIVERSAL ROCKWELL, BRINELL, VICKERS
LD 3000
The LD 3000 hardness tester is a very practical and strong instrument designed to perform Brinell hardness tests at 3000 kg
and other loads starting from 10Kg and also to perform Vickers tests. The integral AFFRI system assures high performance using
automatic selection and application of loads through a simple touch panel. Digital readout of load force and dwell time help the
operator during the test. The test force is closed loop controlled through an electronic load cell connected to the indenter. All
errors linked to weight systems are eliminated, the test is fast and there is an absolute increase in accuracy in every condition.
It includes a clamping cap for secure stability of large parts. The indenter moves through 30 mm into auto contact with the
sample. The operator is required only to push the twin start buttons to initiate the complete test sequence: auto contact with
the test surface ,clamping, application of the test loads, release of sample. At the end of the cycle, the operator can easily
measure the indentation in different systems:
Four different measurement systems
- Through the microscope we supply, in order to obtain Brinell Vickers values (standard).
- AUTOSCAN, which is the electronic microscope for automatic measure (option).
- Integrated automatic measure, without a microscope for fast and serial tests HBT system (option)
- Integrated optical direct readout through camera system and automatic Brinell (option).
It can be operated in areas subject to vibration.
No need to level.
It can work even if inclined.
It can be operated at different temperature ranges from 0 to 50°C.
Technical data (code 4206)
Programmed test forcethrough touch panel and closed loop and load cell inside:
BRINELL loads:
98.1- 147-294-306-613-1226-1839-2452-4905-7357-9810-29430 N
(10-15-30-31.2-62.5-187.5-250-500-750-1000-3000 Kg)
VICKERS loads:
Rockwell (option)
Dwell Time forces
Digital display
Cycle
Clamping
Measure
Field of use
Test height /Test width
Dimensions / Weight
Alimentazione
98.1 - 147 -294 - 490.5 - 981 N Vickers (10 - 15 - 30 - 50 - 100 Kg)
60 100 150 ( 588 981 1471N)
from 5 to 60 seconds programmable
of the selected force, selected test time
only one single start input including travel of indenter and self loading
movable cup and adjustable clamping force till 4000N
Through the microscope; Easy Brinell; Integrated automatic measure; Integrated optical direct readout
all metals from 10 to 600 HB 10 to 2600 HV
300 mm / 160 mm
45 x 70 x 90 h cm / 350 Kg
220 240 V 50 60 Hz
Standard Equipment included in the price
Instruction manual, calibration certificate, dust cover, conversion table, warrantee certificate, electrical connection cable
220V50/60Hz. 0.01 mm high resolution microscope with 6 mm drum scale for Vickers Brinell indentations
Optional: Easy Brinell
(Automatic Optical measure
through autoscan Probe)
Optional accessory: Clamping
base for large or unstable pieces
Optional: Automatic Brinell measure, for
fast test on production department, it
doesn’t need any microscope
Extra accessories
- Clamping base for secure lock samples
- Big flat anvil 150 mm
- Large square table 400 x 300
- Indenter 10 mm
- Indenter 5 mm
- Indenter 2.5 mm
- HRC indenter
- HRB Indenter
- Flat anvil 60 mm diameter for medium pieces
- “V” anvil 60 mm diameter for round pieces
- Test block HB W - 3000 Kg
- Test block HB W - 750 Kg
- Test block HB W - 187.5 Kg
- HRC test block
- HRB Test block
- Vickers 136° Indenter
- Vickers Test block HV 30
- Automeasure
- Automatic HBT Brinell measure
- Easy Brinell
- Integrated screen automeasure
- Autofocus
- Integrated screen and automatic Brinell measure
- Through camera and software to measure in fast
and automatic procedure the brinell and Vickers
indentations
- Objective 20x for load 187.5 - 250
- Obiettive 44x for load 30 - 187.5
- Obiettive 70x for loads 10 - 30
29
®
AFFRI
VIDEO MEASUREMENT
®
ACCESSORIES FOR MISURE BRINELL - VICKERS
1216 MICROSCOPE
• Portable handly microscope
• The most accurate!!
• 0.01 mm division - 20x magnification
• External scale for easy measure
• Not stressing on the eyes
• Scale 6 mm division 0.01 mm
EASY BRINELL
Electronic microscope for automatic Brinell indentation measurement.
Easy:
Put the probe on tested piece and press button.
Brinell result will appear automatically.
Adapt for all type of hardness testers.
Accurate +/- 0.5%
Auto light
Magnetic foot
Can be installed on every PC
Technical characteristics
Programmable for ball
2.5 - 5 - 10 mm diameters
loads 62.5 ÷ 3000 Kg
Division of readout
Repetability
Computer
Conversion table
Weight of probe
Cable
0.1 HB unit
depends on surface roughness +/- 0.5%
minimum configuration Pentium 4, Windows XP, 4 giga HD, 128 mega Ram
inside
0.5 Kg
2 meters
30
AUTOMATIC BRINELL
AFFRI
CK3000
ALL OPERATIONS ARE MANAGED BY A SINGLE DRIVE INCLUDING AUTOMATIC
RESEARCH OF TEST PIECE
- By activating the single Start input button, CK3000 head moves to reach the test surface and automatically starts the hardness test cycle in automatic succession without breacking a phase:
- approach to the piece;
- clamping of the piece;
- activation of reference surface;
- entire test cycle performance and piece releasing.
- It does not require elevating screws
- It meets all laboratory requirements
- Full operation even in presence of vibrations, sudden changes in temperature or dusty environments.
Digital panel
AUTOMATIC BRINELL HARDNESS TESTER
- Performs the HBT measure
ABSOLUTE MEASURE
- The measurement is accurate at the first test and does not require a second test to confirm the result
- No difference of accuracy between stable and unstable test pieces
- Adapts to test forging, cast iron and large components
Optional:
- Its does not require polished surface
Roll supportings for
- Its does not require optical reading
easy movement of
large parts
4207)
Technical characteristics (code
Digital read-out
Test loads
Total height capacity
Depth
Base
Accuracy
Power supply
Measures
Weight
HBWT-500 - HBWT-750 - HBWT-1000 - HBWT-3000
4905 7357 9810 29430N
500 mm - Other on request
250 mm - Other on request
400 x 400 mm
Conformation standards EN-ISO 6506 / JIS
220V 50÷60Hz - 200VA
80x100x200 cm
500 Kg
AUTO3000
•
•
•
•
•
Automatic Brinell tester
Digital Brinell read-out
Test load automatically programmable (4900-7350-9800-29400 N)
Ball indenter 5-10 mm
The head rotates 360°, slides to easily clamp the test piece and automatically executes
Brinell test (HBT)
31
®
AFFRI
AUTOMATIC ROCKWELL - BRINELL HIGH SPEED
®
330 PRS
- High speed hardness tester for fast tests in production departments.
Just one start input and it self executes a complete hardness test including automatically clamping the piece. Up to 1000 tests per hour can be performed.
- Direct readout in Rockwell or Brinell hardness scales programmable in our factory before shipping the machine (others on request)
- Programmable tolerance and electrical data output for fast tested Piece selection
in 3 classes Ok - Hi - Lo
- Very easy to integrate into a conveyor line. The full research of test
sample and automatic cycle including long stroke head and automatic clamping
of the AFFRI® system permits easy connection of the 330 PRS to an existing conveyor line. In addition, a full conveyor line and automatic selector line can be also
studied and created by our company based on customer’s specifications.
VERY HIGH PERFORMANCE
- Unaltered operation even in extreme conditions.
ALL OPERATIONS ARE MANAGED BY A SINGLE DRIVE INCLUDING
AUTOMATIC RESEARCH OF TEST PIECE ➀
- Pushing the Start button, 330 PRS head moves down to reach the test surface
from distance multiples of 50 mm and automatically starts the hardness test
cycle in automatic succession without breaching a phase:
- approach to the piece;
- clamping of the piece;
- activation of reference surface;
- entire test cycle performance and release of piece.
Applicable accessories
Rockwell
- Rockwell C indenter
- Rockwell B indenter
- Rockwell test blocks C-B
Brinell
- Ball penetrator 2.5 - 5 mm
- Brinell test block for ball 2.5 - 5 mm
Technical characteristics (code 1301)
Preload
(10 Kgf) 98.07 N
Test loads
on request
(60 100 150 Kgf) Rockwell 588-980-1471 N
(62.5-125-187.5 Kgf) Brinell 612-1225-1839 N
Feasible tests
Rockwell HRC A D B F G L M R
Brinell HB 30, HB 10, HB 5, R Kgmm2
Mode of operation
automatic
Rockwell+Brinell
Digital reading
0.1 HRC
Reading resolution
Accuracy: Conformation standards EN-ISO 6506 / 6507 / 6508 / ASTM-E18 / JIS
50 mm motorized
Floating head
from 0 to 400 mm
Total height capacity
200 mm
Total depth capacity
Dimension of base
330x390 mm
2000 Kg
Max load of test piece
from 20 to 500 Kgf (from 196 to 4905) N
Clamping pressure of piece
included
Clamping of piece
RS 232 C
Data output
Piece selection
Hard + Soft + Ok
220V 50÷60Hz - 200VA / Pneumatic 4 bar
Power supply
Fields of application
For all metals: iron, steel, tempered steel, bronze, aluminium.
Thickness over 0.6 mm
Net weight
Packing weight
Packing measurements
110 Kg
125 Kg
72x72xH190 cm
32
IN-LINE CUSTOM SOLUTIONS
AFFRI
MATRIX
This hardness tester is endowed with movement on 3 independent axis
and rotation of 360° to allow an easy location of the testing point.
Perfect and effective measurements even at the first test.
SLIM INDENTER
Only one control to operate the movement for test preparing and for the
entire test cycle performance, including the piece clamping phase. It follows that every result is correct even the first test result is accurate and
reliable, so this increases the repeatability of the machine that offers test
accuracy and reading reliability.
With this instrument you can perform tests directly during the manufacturing process, so that the annealing oven staff can be informed about the
test result in real time.
The output qualitative level can be increased without any added cost.
The interesting price of the entire instrument permits a very quick write off
in one year of work.
AUTOMATIC RESEARCH OF TEST PIECE
- If you press Start button, MATRIX moves to reach the test surface and
automatically starts the hardness test cycle in automatic succession
without breaching a phase.
- It does not require elevating screws
- It meets all laboratory requirements
- Full operation even in presence of vibrations, sudden changes in temperature or dusty environments.
MODULAR STRUCTURE
The machine is made with a modular structure so that it can easily fit different test pieces sizes.
EASY DISPLACEMENTS
All movements are on guides with recirculating screws to grant accurate
and easy movement of the test head that accurately places itself in the
different testing points both on crankshaft in supporting diameters and on
connecting rods and camshafts.
AUTOCENTERING
The location of the precise testing point through centering is carried out
automatically by moving head-supporting carriage that centres itself in a
precise and reliable way thanks to an exclusive system.
Technical characteristics
Reading scales
Reading division
Reading
Data output
Setting
Test loads
Accuracy
Test time
Working Depth
Working Height
Machine weight
Power supply
Pneumatic power
HRC or HRN or HV Vickers
0.1 HRC 0.1 HRN 0.1 HV
Digital, with memory
RS 232 C for connection to printer or computer
min. and max. tolerance limits
kg 150 for HRC; kg 30 for HRN; kg 30 for HV
Conformation standards EN-ISO 6508 / JIS
5 second (adjustable)
1000 mm (different on request)
400 mm (different on request)
800 kg ~
220V 50÷60Hz - 200VA
4 BAR
33
®
AFFRI
®
AUTO BRINELL- ROCKWELL
Automatic Brinell-Rockwell tester for tubes, bottles
including: grinding of test area, indentation, automatic
measure and automatic selection of tested piece.
AUTO GM
Automatic system for high speed test for car components “steering pars” to G.M.
On Rockwell Scale, automatic loader, automatic test, automatic sorter: GO - high - low.
1500 pcs per hour.
34
IN-LINE CUSTOM SOLUTIONS
AFFRI
IN-LINE CUSTOM SOLUTIONS
AUTO PRS
Automatic in-line testing system for SKF bearing test.
HRC scale, automatic loader, automatic test, automatic sorter: GO - high - low.
1000 pcs per hour.
Option: light signal for
fast selection go-no go
AUTOMATIC BOLTS
Automatic high speed hardness tester for nuts, bolts, Rockwell C
scale, automatic loader, automatic test, automatic sorter: GO high - low.
1000 pcs per hour.
35
®
AFFRI
CUSTOMIZED SOLUTION
®
HB TWIN
Twin Brinell test: measure with two
different positions simultaneously
with auto alignment HB 10.3000
GAS BOTTLE
Fully automatic system including grinding – Brinell indentation and
automatic optic measurement and movement of gas bottle.
Programmable cycle and step.
36
AFFRI
CUSTOMIZED SOLUTION
HB AUTO TUBE
Fully automatic system with grinding test surface and
Brinell automatic hardness test on cylinders, tubes and
bottle, at high temperatures till 350°.
Load 2.5-187.5 / 10-3000 or Rockwell HRC.
Automatic selection go/no go
AUTOMATIC BRINELL “RADIAL”
Load cell and Cloased Loop Affri system 1839 – 29430N
Capacity 1500 x 1500 mm fully motorized
Table 1500 x 1000 mm
Touch screen 17”
37
®
AFFRI
CUSTOMIZED SOLUTION
®
HB OPTI
Brinell test on casting parts, optical and digital Brinell read-out
10/3000 - 5/750 - 5/250
METALTESTER F1
Vickers tests on crankshaft for Formula 1 (F1)
3302 R
Equipped with sliding table on x-y axes and 360° rotation for test on crankshafts
of scale HRC – HRN.
38
AFFRI
FOR PLASTIC MATERIALS
®
SERIE SHORE
HARDNESS TESTER
In compliance with ASTM 2240, ISO R.868, ISO 7619, DIN 53505, JIS K7215 specifications. For rubber,
plastic, medical components, paper, sponges using Shore A, B, C, D, O, OO, E, M, 000, 000-S scales.
With slim nose to ensure exact measurement even on small components.
For laboratory use connect it with bench stand 13.
Type
Fields of application
3001 - Shore A
3011 - Shore B
3004 - Shore C
3002 - Shore D
- For soft, flexible rubber, plastic, PVC, polyester, neoprene, leather, thiokol, nitril rubbers, tyres, etc.
- As A scale for high values
- As D scale for low values
- Scale for hard and rigid surfaces synthetic materials, acrilics, plexiglass, printing rolls,
cellulose, acetates, densified wood, nylon, derling
3010 - Shore DO
- As B and C
3009 - Shore O
- As A scale for low values
3008 - Shore OO
- For sponges, natural rubber and silicon
3013 - Shore E
- ASTM D 2240 - 02 a
3014 - Shore M
- ASTM D 2240 - 02 a
3015 - Shore 000 - ASTM D 2240 - 02 a
3016 - Shore 000-S - ASTM D 2240 - 02 a
HARDNESS TESTER
In compliance with ASTM 2240, ISO R.868, ISO 7619, DIN 53505, JIS K7215 specifications. For
rubber, plastic, medical components, paper, sponges using Shore A scale.
Easy to use, supplied with clamping system to apply a constant and centered pressure on any sample, even on curved
surfaces, assuring accurate results similar to those obtained through the test with bench support. Suitable for testing
tyres, adapt to test tyres, roll.
Type
Fields of application
3003 - Shore A
- For soft, flexible rubber, plastic, PVC, polyester, neoprene, leather, thiokol,
nitril rubbers, tyres, etc.
Accessories
Second pointer
to memorise the
measurement
(optional)
ART 14
ART 13
ART 16
ART 13
Bench stand for use with analog or digital portable units, it ensures exact and
centered use of the unit on test samples and with a constant pressure.
ART 14
Supplementary weight for Shore C - D - DO models.
ART 16
Set of clamping holders for bench connection in compliance with ASTM 1414 for
precise O-Ring testing (section Ø 1.72 - 2.54 - 3.43 - 5.21 - 6.83 mm)
39
AFFRI
FOR PLASTIC MATERIALS
®
ELECTRONIC
HARDNESS TESTER
Technical characteristics (code 3104)
Hardness Scales each probe
Shore A, D, B, C, O, OO, E, M, OOO, OOO-S, Micro
Standards
DIN 53505 –ISO 868 – 7619 – NFT 51109 – ASTM D 2240 BS 903 Part. A26
Dimensions
Electronic processor: 112 x 180 x 70 mm
Probe diameter 40 foot diameter 16mm
Height 108 mm + Cable
Data transmission
Resolution
Power source
RS 232 C
0.1 unit
6 V CC 250 mA
Fields of applications
all products tested through Shore system
(plastic, rubber, paper, Silicon, PVC, ABS NYLON ….)
Weight
Packing weight
Packing measurements
0.5 Kg probe - 1.4 Kg all complete with processor
4 Kg
470 x 400 x 150 mm in a portable bag
Till 6 probes can be connected and auto calibration
RS232C or USB output data
Art. A078.A1.080
MICRO PROBE A SCALE
for easy inside test
Min 45 mm Ø
Art. A078.A1.080
MICRO PROBE A SCALE
Test on tyres
23631
Clamping handwheel
DMG 03
Motorized Bench support
Height capacity 75 mm
ART. 16
For test on O-ring
Complete Kit bag Including printer
40
AFFRI
FOR PLASTIC MATERIALS
IRHD
Technical characteristics (code 3401)
Working
motorized trough load cell closed loop managed by computer
17” Colour LCD display
Conformation to the Standards
Stroke
Depth
Base for sample
Dimension of machine
Weight
Output data
Power
Packing measures
G.W.
ISO 48 / 7318 / ASTM 1415
50 self research surface sample and max 200 mm
170 mm
60 mm interchangeable
60 x 30 x 80h cm
60 Kg
USB
220 /240 V 15V upon request
100x 100 x 100h cm
90 Kg
Hardness tester for all plastics and rubbers
composit products in accordance to IRHD
PJ 0-100
• Portable tester for PJ tests for paper, roll paper,
paperboard in accordance to P.J. procedure
• Ball indenter included
• Easy and immediate measure on digital display
• Can be utilised directly on roll paper thanks to the self
aligning foot or on flat surfaces
PJ for roll paper
Technical characteristics (code 3200)
The hardness tester is composed by:
- Structure with metal base provided with inlet to place the sample to test, column to support the probe which is adjustable in highness to accept samples of different sizes;
- Electric probe with digital indication of read-out division 0.01 mm., provided with electronic data output for connection to a printer.
- The base to support the sample has adjustable feet and optic level for the levelling of the instrument; to execute test on cylinders of different diameter especially on gummed rolls.
- Handle to transport the instrument to execute tests of hardness directly on big pieces such as gummed rolls.
41
®
AFFRI
ACCESSORIES
®
DIAMOND INDENTERS FOR EVERY TYPE
OF HARDNESS TESTERS
Hardness Test Diamonds according to Rockwell (Rc)
Nr.
Type
Testing appliance
11
Origin. Rockwell 120°
z.B. Frank
12
Testor 120°
Wolpert - Wilson - Time - Mitutoyo
13
Briro UVN 120°
Reicherter
14
Testor-Automat 120°
Wolpert
Nr. 11
Nr. 12
Nr. 13
Nr. 14
Hardness Test Diamonds according to Vickers
Nr.
Type
Testing appliance
15
Origin. Vickers 136°
Vickers - Tukon
16
Vickers 136°
Frank
17
Dia-Testor 136°
Wolpert - Wilson - Time - Mitutoyo
18
Brivisor 3000H 136°
Reicherter
19
VHT 5 136°
Reicherter
Nr. 15
42
Nr. 16
Nr. 17
Nr. 18
Nr. 19
AFFRI
ACCESSORIES
Hardness Test Diamonds according to Vickers
Nr.
Type
Testing appliance
20
Zwick 1 136°
Zwick
21
Zwick 2 136°
Zwick
22
Briviskop 187.5 136°
Reicherter
23
Spare indenter for item 22
Reicherter
24
Testor-Automat 136°
Wolpert
Nr. 20
Nr. 21
Nr. 22
Nr. 23
Nr. 24
Diamonds for Micro hardness Test
Nr.
Type
Testing appliance
25
Mikro 136°
Leitz
26
Mikro-Testor 136°
Wolpert
27
Vickers 136°
Frank
28
Knoop
*
Nr. 25
Nr. 26
Nr. 27
Nr. 28
Shape of Knoop-Diamond
* Knoop-Diamond for all Testing
Appliances
43
®
AFFRI
ACCESSORIES
®
STANDARD TEST BLOCKS
STANDARD TEST BLOCKS WITH UKAS - DKD CERTIFICATE
FOR CALIBRATING HARDNESS TESTERS
A certificate UKAS or DKD is included.
AFFRI CERTIFIED TEST BLOCK TRACEABLE TO UKAS - DKD - SIT
44
AFFRI
ACCESSORIES
NOTES:
The information and technical data present in this catalogue are subject to changes. AFFRI® has the right to modify the current data, at any time, in function of
the evolution of raw material and new technology.
The installation of the products must be executed following the international standards. AFFRI® and its representatives will not accept any responsability due
to incorrect use, connections or installation. Respect of standards, laws and environments where the products are to be used are under the full responsablity of
the installer.
AFFRI®and its representatives will not accept any responsibility for direct or indirect damage caused to persons or things by the products or by
consequences of their use.
45
®
08.01-PR
Sede:
AFFRI® Via M. Tagliaferro, 8 • I - 21056 INDUNO OLONA • CEE - VARESE - ITALIA
Tel. +39 0332 201533 / +39 0332 206289 • Fax +39 0332 203621 • E-Mail [email protected] • www.affri.com
Nord Europe: Sales & Service
AFFRI Testing Instruments BVBA Sprl NIEUWSTRAAT 28 B-3360 KORBEEK-LO
Tel + 32.16.60.66.53 • Fax +32.2.759.90.73 • E-Mail [email protected] • www.affri.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement