MPC-2190 Hardware Manual

Add to my manuals
70 Pages

advertisement

MPC-2190 Hardware Manual | Manualzz

MPC-2190 Panel Computer Hardware

Manual

Second Edition, March 2015 www.moxa.com/product

© 2015 Moxa Inc. All rights reserved.

MPC-2190 Panel Computer Hardware

Manual

The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement.

Copyright Notice

© 2015 Moxa Inc. All rights reserved.

Trademarks

The MOXA logo is a registered trademark of Moxa Inc.

All other trademarks or registered marks in this manual belong to their respective manufacturers.

Disclaimer

Information in this document is subject to change without notice and does not represent a commitment on the part of

Moxa.

Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time.

Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use.

This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication.

Technical Support Contact Information

Moxa Americas

Toll-free: 1-888-669-2872

Tel:

Fax:

+1-714-528-6777

+1-714-528-6778

Moxa Europe

Tel: +49-89-3 70 03 99-0

Fax: +49-89-3 70 03 99-99

www.moxa.com/support

Moxa China (Shanghai office)

Toll-free: 800-820-5036

Tel:

Fax:

+86-21-5258-9955

+86-21-5258-5505

Moxa Asia-Pacific

Tel: +886-2-8919-1230

Fax: +886-2-8919-1231

Table of Contents

1.

Introduction ...................................................................................................................................... 1-1

Overview ........................................................................................................................................... 1-2

Ordering Information .......................................................................................................................... 1-2

Package Checklist ............................................................................................................................... 1-2

Product Features ................................................................................................................................ 1-3

MPC-2190 Hardware Specifications ....................................................................................................... 1-3

MPC-2190 Available Option Table .................................................................................................. 1-5

Hardware Block Diagram ..................................................................................................................... 1-6

2.

Hardware Introduction...................................................................................................................... 2-1

Appearance ........................................................................................................................................ 2-2

Front View .................................................................................................................................. 2-2

Bottom View ............................................................................................................................... 2-2

Dimensions ........................................................................................................................................ 2-3

SavvyTouch Display Control Buttons ..................................................................................................... 2-3

Real Time Clock .................................................................................................................................. 2-4

3.

Hardware Connection Description ..................................................................................................... 3-1

Placement Notes ................................................................................................................................. 3-2

Desktop Mounting ....................................................................................................................... 3-3

Wall Mounting ............................................................................................................................. 3-3

VESA Mounting ........................................................................................................................... 3-5

Wiring Requirements ........................................................................................................................... 3-6

Temperature Requirements .................................................................................................................. 3-6

Important Safety Precaution ......................................................................................................... 3-6

Grounding the MPC-2190 Series ........................................................................................................... 3-6

Powering on/off the MPC-2190 Series .................................................................................................... 3-7

SavvyTouch Display Control Buttons .............................................................................................. 3-7

Extending the Displays ........................................................................................................................ 3-8

Connecting Data Transmission Cables ................................................................................................... 3-9

Connecting to a Network .............................................................................................................. 3-9

Connecting to a Serial Device ..................................................................................................... 3-10

Connecting to NMEA 0183 Devices .............................................................................................. 3-12

Connecting to a Speaker or a Headphone ............................................................................................ 3-12

Connecting a PS/2 Keyboard and Mouse .............................................................................................. 3-12

Connecting to USB Devices ................................................................................................................ 3-12

Installing a SATA HDD or SSD ............................................................................................................ 3-13

4.

Display Resolution and Touch Calibration ......................................................................................... 4-1

Installing the VGA Driver ..................................................................................................................... 4-2

Adjusting Display Resolution ................................................................................................................ 4-6

Installing the Touchscreen Driver .......................................................................................................... 4-7

Screen Calibration ............................................................................................................................ 4-12

5.

BIOS Setup ........................................................................................................................................ 5-1

Entering the BIOS Setup Utility ............................................................................................................ 5-2

Main Information ................................................................................................................................ 5-3

Advanced Settings .............................................................................................................................. 5-3

Boot Configuration....................................................................................................................... 5-4

HDC Configuration ....................................................................................................................... 5-4

Video Configuration ..................................................................................................................... 5-5

Chipset Configuration................................................................................................................... 5-7

Hardware Monitor ........................................................................................................................ 5-8

Security Settings ................................................................................................................................ 5-8

Set Supervisor Password .............................................................................................................. 5-9

Power Settings ................................................................................................................................... 5-9

Boot Settings ................................................................................................................................... 5-10

Boot Type ................................................................................................................................. 5-10

PXE Boot to LAN ........................................................................................................................ 5-10

Add Boot Options ...................................................................................................................... 5-10

USB Boot ................................................................................................................................. 5-10

EFI Device First ......................................................................................................................... 5-10

Boot Delay Time ........................................................................................................................ 5-11

Legacy ..................................................................................................................................... 5-11

Exit Settings .................................................................................................................................... 5-12

Exit Saving Changes .................................................................................................................. 5-12

Save Change Without Exit .......................................................................................................... 5-12

Exit Discarding Changes ............................................................................................................. 5-12

Load Optimal Defaults ................................................................................................................ 5-12

Load Custom Defaults ................................................................................................................ 5-12

Save Custom Defaults ................................................................................................................ 5-13

Discard Changes ....................................................................................................................... 5-13

Upgrading the BIOS .......................................................................................................................... 5-13

6.

Display Control Interface .................................................................................................................. 6-1

Connecting to the Console Interface ...................................................................................................... 6-2

Display Control Interface Command Format ........................................................................................... 6-4

Command Format Description ....................................................................................................... 6-4

Downloading RGB Files ........................................................................................................................ 6-7

A.

Regulatory Approval Statement ........................................................................................................ A-1

B.

Display Control Interface Commands ................................................................................................ B-1

Display Control Interface Commands ..................................................................................................... B-2

BRI (Brightness Minimum Value) ................................................................................................... B-2

BRL (Set LED Brightness of Touch Keypad) ..................................................................................... B-2

BRM (Brightness Maximum Value) ................................................................................................. B-2

BRT (User Brightness Control) ...................................................................................................... B-2

BRU (Glass Display Control-Brightness Button) ............................................................................... B-2

BZZ (Buzzer Control) ................................................................................................................... B-3

DLN (Download ECDIS RGB Package) ............................................................................................ B-3

DL? (ECDIS RGB Package Query) .................................................................................................. B-3

ETC (Elapsed Time Counter Query) ................................................................................................ B-3

GMB (Glass Display Control - Minimum Brightness) ......................................................................... B-4

POT (Potentiometer Control) ......................................................................................................... B-4

SWI (Scalar Firmware Version Query) ............................................................................................ B-4

SWK (Touch Keypad Firmware Version Query) ................................................................................ B-4

ADF (AC Input Power Detect Function) ........................................................................................... B-4

AD? (Query AC Input Power Detect Function Status) ........................................................................ B-5

BLI (Brightness Control) ............................................................................................................... B-5

DUF (Disable UART Command Function) ......................................................................................... B-5

EMS (ECDIS Mode Select) ............................................................................................................ B-5

1

1.

Introduction

In this chapter, we give a general introduction to the features and specifications of MPC-2190 panel computers.

The following topics are covered in this chapter:

Overview

Ordering Information

Package Checklist

Product Features

MPC-2190 Hardware Specifications

MPC-2190 Available Option Table

Hardware Block Diagram

MPC-2190 Hardware Introduction

Overview

MPC-2190 panel computers feature advanced Intel processors—3rd generation Ivy Bridge Core or

Celeron—matched to 4 GB of system memory, to deliver a reliable, high-performance platform of wide versatility for use in industrial marine environments. With its RS-232/422/485 serial, NMEA 0183, and Gigabit

Ethernet LAN ports, the MPC-2190 panel computer supports a wide variety of serial- and marine-specific interfaces alongside high speed IT communications, all with native network redundancy.

The MPC-2190 series comes with a range of standard display enhancements useful in industrial environments

(including 0 to 100% full range dimming, 178°/178° wide viewing angles, optional optical bonding, and/or multi-touch screen), as well as Moxa’s innovative SavvyTouch display controls.

MPC-2190 panel computers are compliant with several industrial marine standards, such as IEC 60945 4th, IEC

61174, IEC 61162, DNV2.4, and IACS E10, verifying their resilient durability in marine operations. An optional

IP65-rated unibody shell provides strong additional protection against the harsh conditions found in marine environments. The MPC-2190 delivers a rugged, type approved, high-performance and user-friendly panel computer perfect for ECDIS navigation systems and other marine IBS applications.

Ordering Information

The MPC-2190 series includes the following models:

MPC-2190X: 19-inch fanless panel computer with Intel Celeron 1047UE 1.4 GHz processor, NMEA 0183,

RS-232/422/485 serial ports, Gigabit Ethernet LAN ports, USB 2.0 ports, dual AC/DC power inputs, and tape bonding

MPC-2190Z: 19-inch fanless panel computer with Intel Celeron 1047UE 1.4 GHz processor, NMEA 0183,

RS-232/422/485 serial ports, Gigabit Ethernet LAN ports, USB 2.0 ports, dual AC/DC power inputs, and tape bonding, projected capacitive touchscreen

MPC-2197X: 19-inch fanless panel computer with Intel Core i7 2610UE 1.5 GHz processor, NMEA 0183,

RS-232/422/485 serial ports, Gigabit Ethernet LAN ports, USB 2.0 ports, dual AC/DC power inputs, and tape bonding

The following optional accessory packages are available on request:

• Desktop mounting kit

• Wall mounting clamps

• VESA mounting kit

Package Checklist

The MPC-2190 panel computer is shipped with the following items:

• 1 MPC-2190 series panel computer

• 1 terminal block for DC power input

• 4 5-pin Euroblock terminals for NMEA 0183 v2 interfaces

• 2 HDD installation brackets

• Documentation and driver DVD

• Quick installation guide (printed)

• Warranty card

NOTE

Notify your sales representative if any of the above items are missing or damaged.

1-2

MPC-2190 Hardware Introduction

Product Features

The MPC-2190 series panel computer has the following features:

• 19-inch panel

• Color calibrated for ECDIS compliance

• Fanless design

• SavvyTouch display controls

• 3rd Generation Intel® Core™ or Celeron® processor (default: Celeron® 1047UE, 1.40 GHz with Intel® HD

Graphics)

• Built-in NMEA 0183 and software selectable RS-232/422/485 interfaces (DI/DO and LPT available on request)

• Dual AC/DC power supply units

• Optically bonded and touch panel models available on request

MPC-2190 Hardware Specifications

Computer

CPU: lntel Celeron® Processor 1047UE (2M Cache, 1.4 GHz)

OS: Windows 7 Professional, Windows Embedded Standard 7, Windows XP Embedded, Windows XP SP3

(models with OS pre-installed available on request)

System Chipset: Intel BD82HM65 platform controller hub

System Memory: 4 GB pre-installed: 1 slots of 4 GB DDR3-1066 204 pin SO-DIMM SDRAM

USB: USB 2.0 hosts x 4, type A connectors, supporting system boot up

Storage: 2 SATA-III connectors

BIOS: 64 Mbit Flash BIOS SPI type, ACPI function supported

Graphics Controller: Intel HM65 Express chipset built-in

Video Output: DVI-D x 1, VGA x 1 (female)

Digital Input/Output: 4 DIs, 4 DOs, or 8 DIs, 8 DOs (optional)

LPT Port: 1 (available on request)

Buzzer: 75 to 85 db (IEC 60945 complied)

Other Peripherals

Audio: Line-in and line-out interface, with 3.5 mm mini jack

KB/MS: 2 PS/2 interface supporting standard PS/2 keyboard and mouse

Display

Panel Size: 19 inch wide viewable image size

Panel Type: MVA

Aspect Ratio: 5:4

Pixels: 1280 x 1024 (SXGA)

Response Time: 20 ms

Contrast Ratio: 2000:1

Light Intensity: 300 cd/m^2

Viewing Angles: 178°/178°

Active Display Area: 376.32 (H) x 301.06 (V) mm

Max Colors: 16.7M (8 bits/color)

Display Interface: Dual channel LVDS

Resolution:

• VGA: 640 x 480

• SVGA: 800 x 600

• XGA: 1024 x 768

• SXGA: 1280 x 1024

Ethernet Interface

1-3

MPC-2190 Hardware Introduction

LAN: 2 auto-sensing 10/100/1000 Mbps ports (RJ45)

Magnetic Isolation Protection: 1.5 kV built-in

Serial Interface

Serial Standards: 2 RS-232/422/485 ports, software-selectable (DB9 male)

Serial Communication Parameters

Data Bits: 5, 6, 7, 8

Stop Bits: 1, 1.5, 2

Parity: None, Even, Odd, Space, Mark

Flow Control: RTS/CTS, XON/XOFF, ADDC® (automatic data direction control) for RS-485

Baudrate: 50 bps to 115.2 Kbps (supports non-standard baudrates; see user’s manual for details)

Serial Signals

RS-232: TxD, RxD, DTR, DSR, RTS, CTS, DCD, GND

RS-422: TxD+, TxD-, RxD+, RxD-, GND

RS-485-4w: TxD+, TxD-, RxD+, RxD-, GND

RS-485-2w: Data+, Data-, GND

NMEA Interface

Serial Standards: 4 NMEA 0183 ports

Base Serial Standard: RS-422

Optical Isolation Protection: ±6kV contact discharge, ±8kV air discharge

Voltage Differential: -15 V to + 15 V

Baudrate: 4800 bps

Data Bits: 8

Stop Bits: 1, 1.5, 2

Parity: None

Handshake: None

LEDs

System: Storage, Power

LAN: 100M/Link x 2, 1000M/Link x 2 (on connector)

Front Panel

LEDs: MENU, Brightness, INFO, ECDIS, Day/Dusk/Night, Storage

Smart OSD: Yes

Physical Characteristics

Housing: Aluminum sheet metal

Weight: 7.8 kg

Dimensions: 429 x 387 x 74.5 mm (16.89 x 15.24 x 2.93 in)

Mounting: Flush mounting

System Cooling: Fanless thermal design

Environmental Limits

Operating Temperature: -15 to 55°C (5 to 131°F)

Storage Temperature: -20 to 60°C (-4 to 140°F)

Ambient Relative Humidity: 5 to 95% (non-condensing)

IP Rating:

• Front: IP 54

• Rear: IP 22

Anti-Vibration:

• 0.7 g @ DNV 2.4 (Class A), sine wave, 2-100 Hz, 1 Oct./min., 1.5 hr per axis

• 1 g @ DNV 2.4, random wave, 3-100 Hz, 2.5 hr per axis

• 1 g @ DNV 2.4 (Class C), sine wave, 2-50 Hz, 1 Oct./min., 1.5 hr per axis

Power Requirements

Input Voltage: 115 to 230 VAC, 50/60 Hz, 24 VDC

Power Consumption: 40 W to 125 W (max.)

Standards and Certifications

Safety: UL 60950-1, CCC

1-4

MPC-2190 Hardware Introduction

EMC: EN 55022 Class B, EN 55024-4-2, EN 55024-4-3, EN 55024-4-4, FCC Part 15 Subpart B Class A

Marine Standard: IEC-60945 4th, IEC-61162, IEC-61174

Marine Type Approval: DNV 2.4 and IACS E10, ABS, MR-A003

Green Product: RoHS, cRoHS, WEEE

Reliability

MTBF (mean time between failures): 202,309 hrs

Automatic Reboot Trigger: Built-in WDT (watchdog timer) supporting 1-255 levels for time interval system reset, software programmable

Warranty

Warranty Period: 1 year

Details: See www.moxa.com/warranty

MPC-2190 Available Option Table

The MPC-2190 can be customized with different hardware specifications. Refer to the following table for details.

CPU

RAM

OS

Factory

Options

Default

Options

Default

Option lntel Celeron® processor 1047UE (2M Cache, 1.40GHz), TDP 17 watts lntel Core™ i3 processor 3217UE (3M Cache, 1.60GHz), TDP 17 watts lntel Core™ i7 processor 3517UE (4M Cache, 2.80GHz), TDP 17 watts

4 GB

8 GB (max.)

Default

Options

N/A

Windows 7 Professional

Windows XP Embedded

Windows Embedded Standard 7

Windows XP SP3

Linux Debian 7

Projected capacitive touch screen (multi-touch, USB interface)

Optical bonding

Customized options for SSD drives

1-5

MPC-2190 Hardware

Hardware Block Diagram

Introduction

1-6

2

2.

Hardware Introduction

The MPC-2190 Series computer is compact, well-designed, and ruggedized for marine applications. The intelligent SavvyTouch display control buttons allow you to indicate control buttons easily in low light environment and identify system hardware failure easily. Multiple serial ports allow you to connect different devices for data operation, and the reliable and stable hardware platform lets you devote your attention to developing your applications.

The following topics are covered in this chapter:

Appearance

Front View

Bottom View

Dimensions

SavvyTouch Display Control Buttons

Real Time Clock

MPC-2190 Hardware

Appearance

Front View

Hardware Introduction

Bottom View

2-2

MPC-2190 Hardware

Dimensions

Hardware Introduction

SavvyTouch Display Control Buttons

The MPC-2190 comes with SavvyTouch display control buttons located at the lower right corner of the front surface. These intelligent buttons will light up automatically when your fingers draw near. Refer to the following table for the function of each button.

Name

Power

Displayed

Color

Green

Red

Off

Brightness White

Control Function / Color Legend

Computer is powered on and functioning normally

Power standby and system shut down

Power is off.

+: To increase brightness of panel

-: To decrease brightness of panel

System functioning normally

System hardware error

Info Off

Red

Storage

Display mode

Red (on) Storage drive is functioning properly

Red (blinking) Drive is accessing or writing data

Off Drive is offline.

White Displays the brightness mode

Off Panel brightness out of ECDIS standard range

2-3

MPC-2190 Hardware Hardware Introduction

Real Time Clock

The computer’s real-time clock is powered by a lithium battery. We strongly recommend that you NOT replace the lithium battery on your own. If the battery needs to be changed, please contact the Moxa RMA service team.

ATTENTION

There is a risk of explosion if the wrong type of battery is used. To avoid this potential danger, always be sure to use the correct type of battery. Contact the Moxa RMA service team if you need to replace your battery.

2-4

3

3.

Hardware Connection Description

In this chapter, we show how to connect the panel computer to the network and to various devices.

The following topics are covered in this chapter:

Placement Notes

Desktop Mounting

Wall Mounting

VESA Mounting

Wiring Requirements

Temperature Requirements

Important Safety Precaution

Grounding the MPC-2190 Series

Powering on/off the MPC-2190 Series

SavvyTouch Display Control Buttons

Extending the Displays

Connecting Data Transmission Cables

Connecting to a Network

Connecting to a Serial Device

Connecting to NMEA 0183 Devices

Connecting to a Speaker or a Headphone

Connecting a PS/2 Keyboard and Mouse

Connecting to USB Devices

Installing a SATA HDD or SSD

MPC-2190 Hardware Hardware Connection Description

Placement Notes

Before installing and mounting the MPC-2190 panel computer, please read the following notes:

1. The MPC-2190 series is designed for various installation or mounting methods, for example: desktop mounting, wall mounting, and VESA mounting. Please refer to the relevant mechanical drawings in the next sections before attempting to mount the panel.

2. It is advised that good ventilation is necessary to prolong the computer’s lifespan. The chassis’ heat-sink area MUST be kept clear from other heat generating items, as this may damage the system motherboard.

The minimal distance is 150 mm.

3. Allow sufficient physical space for proper ventilation, cable connectors, wiring passage, and pracitcal maintenance purposes.

4. DO NOT install the unit in a horizontal position (laying down), as the heat inside of the unit is not dissipated effectively and will damage the LCD panel. It is recommended to install the unit in a vertical position (±30 degrees) for better heat dissipation.

5. Exposure to extreme direct sunlight may cause a considerable increase in the temperature of the unit, and under certain circumstances might lead to overheating. Please take this point into consideration when the bridge equipment is being planned (sun shades, distance from the windows, ventilation, etc.)

6. Exposure to strong vibration or acoustic noise might affect the functionality and expected lifetime of the computer. Take consideration of these factors during system assembly and installation, to ensure the mounting position avoids exposure to strong vibrations.

7. For maximum safety, at least two persons should work together to lift, place, and fasten the computer to its mounting point. Before you lift or move the computer, first verify the computer is disconnected from any power source, and turned off. In addition, make sure you have prepared the correct screws for a wall mounting.

3-2

MPC-2190 Hardware Hardware Connection Description

Desktop Mounting

The MPC-2190 comes with optional brackets that allow you to temporarily install the panel computer on a horizontal surface, such as a desktop. Three round screws are required for each bracket. See the figure below for detailed screw specifications and their torque value.

Desktop mounting of this sort is intended as a temporary workaround when configuring or testing the computer before permanent installation. The desktop mounting brackets should not be used for permanent installations.

Place your MPC-2190 Series panel computer on a clean, flat, well-ventilated desktop. For better ventilation, leave some space between the MPC-2190 Series and other equipment. Do not place equipment or objects on top of the MPC-2190 Series panel computer, as this might damage the computer’s internal components.

Wall Mounting

The MPC-2190 Series comes with 14 optional clamp mounts that allow for installation onto a wall (where space has been cut out to accommodate the rest of the hardware) or into computing stations where a flush mount is desired. The maximum thickness of the surface to which the computer will be clamped is 11 mm. For a secure mounting, all 14 clamps must be used. The clamp arms are fastened into slots on all four sides of the

MPC-2190. Use the short M4 SUS (stainless) screws to fasten the clamp arms to the MPC-2190 mounting slots, as shown in the magnified inset in the diagram at the top of the next page. Next, use the clamps to fasten the computer to its mounting point; please note the torque value that is shown in the figure inset below.

3-3

MPC-2190 Hardware Hardware Connection Description

3-4

MPC-2190 Hardware Hardware Connection Description

VESA Mounting

The MPC-2190 also comes with an optional VESA mounting kit. Six flat screws and four round screws are required to fasten the VESA mounting bracket. See the figure below for detailed screw specifications and torque values.

An additional four screws (not included in the kit) are required to mount the computer on a VESA rack. For this purpose, use M6 screws with a length between 10 and 12 mm.

3-5

MPC-2190 Hardware Hardware Connection Description

Wiring Requirements

This section describes how to connect peripheral devices to the panel computer.

You should read and follow these common safety precautions before proceeding with the installation of any electronic device:

• Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point.

NOTE

Do not run signal or communication wiring together with power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.

• Use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.

• Keep input wiring and output wiring separate.

• It is advisable to label the wiring to all devices in the system.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or wiring your MPC-2190 Series.

Wiring Caution!

Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equipment.

Temperature Requirements

Be careful when handling the unit. When the unit is plugged in, the internal components generate heat, and consequently the outer casing may feel hot to the touch.

We recommend taking the following precautions to minimize heat build-up within the display:

• Position the display within ±40° of the vertical.

• Install an external fan to increase airflow upwards through the display if (a) the display is not positioned within ±40° of the vertical, (b) the ambient temperature exceeds 25°C, or (c) the display is used in a location with minimal ventilation.

Important Safety Precaution

Even though the display is rated to operate within the IEC 60945 standard of -15 to 55°C for marine applications, it is best to ensure that the ambient temperature does not exceed 25°C. Doing so will increase the life of your display and minimize service costs.

Grounding the MPC-2190 Series

Before you power on the MPC-2190 Series, please ground the MPC-2190 as grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting the power.

3-6

MPC-2190 Hardware Hardware Connection Description

ATTENTION

This product is intended to be mounted to a well-grounded mounting surface, such as a metal panel.

Grounding: See the figure shown below for the location of the grounding connector. Connect the grounding wire to an appropriate grounded metal surface.

Powering on/off the MPC-2190 Series

To power on the MPC-2190 Series you may connect the Terminal Block to Power Jack Converter to the

MPC-2190 Series DC terminal block (located on the bottom surface) and then connect a power adapter; or, alternatively, you may power the device using the AC power cord. Touch the MENU button (in the lower right corner of the display panel) for 1 second to turn on the computer. It takes about 10 to 30 seconds for the system to boot up.

To power off the MPC-2190 Series, touch the MENU button for 4 seconds; depending on your OS’s power management settings you may enter standby, hibernation, or system shutdown mode. If you encounter technical problems, touch the MENU button again this time for 10 seconds to force a hard shutdown of the system.

NOTE: If the MPC-2190 is powered using a DC converter the INFO dialog will display an Error message as the

AC power status. This will not affect the MPC-2190’s operation.

SavvyTouch Display Control Buttons

The MPC-2190 Series comes with five SavvyTouch display control buttons located on the front surface. These intelligent controls will light up with the your hand draws near over the area of the screen where they are located.

MENU

The MENU button operates like a power button, with which users may start up or shut down the computer.

Holding the button for 1 second will power on the system, and the button will light up a solid green. To power off the MPC-2190, press and hold the Menu button for 4 seconds to enter standby, hibernation, or system

3-7

MPC-2190 Hardware Hardware Connection Description

shutdown mode, depending on the power management settings you have set in your operating system. If a hard shutdown is required because of technical problems, press and hold the Menu button for 10 seconds to forcibly power off the system.

Brightness

Two brightness buttons are available for brightness control. Press the + button to increase the brightness of the panel, and the button to decrease the brightness.

INFO

The INFO button returns the current system status for various components, such as power for AC input and main board, CPU, memory, chipset and VGA output. Pass will indicate that the subsystem is working well. An error message will be shown when the system is not working. CPU, memory, chipset and VGA output will be detected only at the bootup stage; any changes or failures that occur after that will not be registered by the system. The AC power and mainboard power (Main Board Power) options will be continuously detected, even after the computer has been booted up.

ECDIS

Touch the button to switch between DAY, DUSK, and NIGHT display modes.

Upon touching the ECDIS button, the brightness configuration will be overwritten to day, dusk, or night modes.

NOTE

(Storage)

A storage icon can also be found on the panel. When data access occurs, it will display a blinking red status.

The display of the MPC-2190 can also be controlled with a series of commands. For a list of the available commands and their uses, refer to Appendix B: Display Control Interface Commands for details

Extending the Displays

The MPC-2190 comes with both standard VGA (DB15) and DVI-D (DB24) interfaces on the bottom surface.

They may be used simultaneously to extend the display across two monitors. See the following figures and tables for the location and pin assignments for the display outputs.

3-8

MPC-2190 Hardware Hardware Connection Description

DB15 Female Connector

3

4

5

6

Pin No. Signal Definition Pin No. Signal Definition

1

2

Red

Green

9

10

VCC

GND

7

8

Blue

NC

GND

GND

GND

GND

11

12

13

14

15

NC

DDC2B Data

HSYNC

VSYNC

DDC2B Clock

DVI-D Connector

Pin Signal Definition

1 T.M.D.S. Data2-

2 T.M.D.S. Data2+

3 T.M.D.S. Data2 Shield

4 N/C

5 N/C

6 DDC Clock

7 DDC Data

8 N/C

9 T.M.D.S. Data1-

10 T.M.D.S. Data1+

11 T.M.D.S. Data1 Shield

12 N/C

Pin Signal Definition

13 N/C

14 +5V Power

15 Ground (return for +5V,

HSync, and VSync)

16 Hot Plug Detect

17 T.M.D.S. Data0-

18 T.M.D.S. Data0+

19 T.M.D.S. Data0 Shield

20 N/C

21 N/C

22 T.M.D.S. Clock Shield

23 T.M.D.S. Clock+

24 T.M.D.S. Clock-

Connecting Data Transmission Cables

This section describes how to connect the MPC-2190 panel computer to a network, or serial devices.

Connecting to a Network

Plug an Ethernet cable into the MPC-2190’s Ethernet port. The other end of the cable should be plugged into your Ethernet network. When the cable is properly connected, the LEDs on the panel computer’s Ethernet port will glow to indicate a valid connection. See the following figure for the location of the Ethernet ports.

3-9

MPC-2190 Hardware Hardware Connection Description

The 10/100/1000 Mbps Ethernet LAN port uses 8-pin RJ45 connectors. The following diagram shows the pinouts and the descriptions for these ports.

LAN

(on connectors)

Green

Yellow

Off

100 Mbps Ethernet mode

1000 Mbps (Gigabit) Ethernet mode

No activity or 10 Mbps Ethernet mode

Pin 100 Mbps 1000 Mbps

1 ETx+ TRD(0)+

2 ETx-

3 ERx+

TRD(0)-

TRD(1)+

4 –

5 –

6 ERx-

TRD(2)+

TRD(2)-

TRD(1)-

7 –

8 –

TRD(3)+

TRD(3)-

Connecting to a Serial Device

Use a serial cable to plug your serial device into the MPC-2190’s serial port. Serial ports 1 and 2 have male DB9 connectors and can be configured for RS-232, RS-422, or RS-485 communication by software. See the following figure for the location of the serial ports.

The pin assignments are shown in the table at the top of the next page:

3-10

MPC-2190 Hardware

DB9 Male Port

Hardware Connection Description

4

5

6

7

8

1

2

3

RS-232/422/485 Pinouts

Pin RS-232 RS-422

DCD

RxD

TxD

DTR

GND

DSR

RTS

CTS

TxDA(-)

TxDB(+)

RxDB(+)

RxDA(-)

GND

RS-485

(4-wire)

TxDA(-)

TxDB(+)

RxDB(+)

RxDA(-)

GND

RS-485

(2-wire)

DataB(+)

DataA(-)

GND

Configuring RS-232/422/485 Serial Ports

For configuring the RS-232/422/485 serial port, please go to the following path and find the configuration example.

For the Windows 32-bit platform:

<Software DVD>\example\MPC-2190\Release\UartMode

For the Windows 64-bit platform

<Software DVD>\example\MPC-2190\x64\Release\UartMode

Select 1 to get the current UART mode; select 2 to configure the UART mode.

Enter the port number you want to configure, and then enter the mode. For RS-232 mode, enter 0; for

RS-485-2W mode, enter 1, for RS-422/RS-485-4W mode, enter 1.

3-11

MPC-2190 Hardware Hardware Connection Description

Connecting to NMEA 0183 Devices

The MPC-2190 comes with eight NMEA 0183 ports on the bottom surface. Check the following figures for the location of these ports and the pin assignments.

Connecting to a Speaker or a Headphone

The MPC-2190 comes with line-in and line-out interfaces for connecting a microphone and either speakers or headphones. See the following figure for the location.

Connecting a PS/2 Keyboard and Mouse

Your MCP-2190 computer comes with two PS/2 connectors to connect to a PS/2 keyboard (upper connector) and PS/2 mouse (lower connector). See the following figure for the locations.

Connecting to USB Devices

The MPC-2190 comes with 4 USB 2.0 ports on the computer. The ports can be used for an external flash disk or hard drive for data storage expansion. You can also use these USB ports to connect to a keyboard or a mouse.

3-12

MPC-2190 Hardware Hardware Connection Description

Installing a SATA HDD or SSD

The MPC-2190 has an optional HDD/SSD installation kit. To install the 2.5-inch SATA storage, follow these instructions. For better system reliability, we suggest you use a solid state disk (SSD).

1. Remove the seven screws on the back of the MPC-2190.

2. Remove the back cover of the MPC-2190, and find the installation area.

3-13

MPC-2190 Hardware Hardware Connection Description

3. Install the HDD or SSD into the bracket, and fasten four screws onto two sides of the bracket.

4. Place the HDD or SSD into the installation area inside the MPC-2190. Fasten the four bracket screws (shown below, in the red circles), and connect the SATA cable to the HDD or SSD.

NOTE

5. Replace the cover of the MPC-2190, and fasten the screws to finish.

For fastening the screws on the cover of the MPC-2190 panel computer, we suggest you use the T10 Trox (Star) screwdriver with a torque of 4.5kg.

3-14

4

4.

Display Resolution and Touch Calibration

This chapter describes how to install the VGA driver and the touch driver for the touchscreen models. After installing the drivers, you may use the tools described below to adjust the display resolution and the touch response of your panel computer.

The following topics are covered in this chapter:

Installing the VGA Driver

Adjusting Display Resolution

Installing the Touchscreen Driver

Screen Calibration

MPC-2190 Hardware Display Resolution and Touch Calibration

Installing the VGA Driver

The MPC-2190 comes with a stock VGA driver for Windows Embedded Standard 7. Follow these steps to install.

1. On the product CD go to the Driver folder and select Win7. Select either 32-bit or 64-bit, according to your platform, then select 2.VGA folder.

2. Double-click Win32_15319 to continue.

4-2

MPC-2190 Hardware Display Resolution and Touch Calibration

3. The installation wizard will be launched; click Next to continue.

4. Click Next to start the installation.

5. Click Yes to accept the license agreement.

4-3

MPC-2190 Hardware

6. Click Next to continue.

Display Resolution and Touch Calibration

7. The installation will begin. Wait until it finishes.

4-4

MPC-2190 Hardware

8. Click Next to continue.

Display Resolution and Touch Calibration

9. Select Yes, and then click Finish to complete the VGA driver installation.

10. The MPC-2190 will restart, and you may now adjust the display resolution with the tool provided by Intel.

4-5

MPC-2190 Hardware Display Resolution and Touch Calibration

Adjusting Display Resolution

Follow these steps to adjust the display resolution.

1. Right-click the Intel HD Graphics Control Panel icon on the right down corner of the screen, and select

Graphics Properties.

2. Select Display.

3. You can now adjust the resolution, refresh rate, and the display rotation. Select Maintain Display Scaling, to maximize the display so it fits the screen. Click Apply when finished.

4-6

MPC-2190 Hardware Display Resolution and Touch Calibration

4. If you want to adjust the display size, select Customize Aspect Ratio, and adjust by pulling the bars on the right.

5. Click Apply when finished.

Installing the Touchscreen Driver

For touchscreen models, you need to install the touchscreen driver. Follow these steps.

1. In the Driver folder, select 7.Touch folder.

2. Select eGalaTouch_7_Vista_XP_2K_5.11.0.9126 folder.

4-7

MPC-2190 Hardware

3. Select eGalaxTouch_5.11.0.9126 folder.

Display Resolution and Touch Calibration

4. Select setup in the folder for the installation.

5. Click Next to continue.

4-8

MPC-2190 Hardware Display Resolution and Touch Calibration

6. You do not need to check Install PS/2 interface drive. Click Next to continue.

7. Check Install RS232 interface drive. Click Next to continue.

8. You may select the time to do touch screen calibration and then click Next to continue.

4-9

MPC-2190 Hardware Display Resolution and Touch Calibration

9. If you want this computer to be a touchscreen interface, click OK to continue.

10. You may check Support Mulit-Monitor System, and then click Next to continue.

11. You may select the destination folder by clicking Browse, and then click Next.

12. Click Next to continue.

4-10

MPC-2190 Hardware Display Resolution and Touch Calibration

13. You may Create an eGalaxTouch Utility shortcut on desktop by clicking the appropriate box. Click

Next to continue.

14. The installation will start, and wait until it finishes.

15. When finished, click Yes. You can do the 4 point calibration for the touch function.

16. Click the circle in the corner until it shows OK.

4-11

MPC-2190 Hardware

17. Click OK to complete.

Display Resolution and Touch Calibration

Screen Calibration

Please note that you need to do 4 point calibration whenever you change the display resolution, to maintain touchscreen accuracy. Follow these steps.

1. Run eGalaxTouch by double-clicking the icon on the desktop.

2. Select Tools tab, and click 4 Points Calibration item.

3. Click the circle in the corner until it shows OK.

4-12

MPC-2190 Hardware

4. Click OK to complete.

Display Resolution and Touch Calibration

4-13

5

5.

BIOS Setup

This chapter describes the BIOS settings of the MPC-2190 Series computer. The BIOS is a set of input/output control routines for peripherals. The BIOS is used to initialize basic peripherals and helps boot the operating system before the operating system is loaded. The BIOS setup allows the user to modify the system configurations of these basic input/output peripherals. All of the configurations will be stored in the battery backed up CMOS RAM, which retains the system information after system reboots or the power is removed.

The following topics are covered in this chapter:

Entering the BIOS Setup Utility

Main Information

Advanced Settings

Boot Configuration

HDC Configuration

Video Configuration

Chipset Configuration

Hardware Monitor

Security Settings

Set Supervisor Password

Power Settings

Boot Settings

Boot Type

EFI Device First

Boot Delay Time

Legacy

Exit Settings

Exit Saving Changes

Save Change Without Exit

Exit Discarding Changes

Load Optimal Defaults

Load Custom Defaults

Save Custom Defaults

Discard Changes

Upgrading the BIOS

MPC-2190 Hardware BIOS Setup

Entering the BIOS Setup Utility

To enter the BIOS setup utility, press the “F2” key while the system is booting up. The main BIOS Setup screen will appear. Select SCU to enter the BIOS configuration.

NOTE

The projected capacitive touch screen function is not supported in BIOS, connect a keyboard to the MPC-2190 for BIOS configuration.

A basic description of each function key is listed at the bottom of the screen. Refer to these descriptions to learn how to use them.

F1: General Help

F5/F6: Change Values

F9: Setup Defaults

F10: Save and Exit

↑↓

: Select Item

: Select Menu

ESC: Exit

ENTER: Select or go to Submenu.

5-2

MPC-2190 Hardware BIOS Setup

Main Information

The main page indicates the system information, such as model name, BIOS version, and CPU type. User may view the basic system hardware information in the page.

Advanced Settings

The “Advanced Features” screen will appear when choosing the “Advanced” item from the main menu.

5-3

MPC-2190 Hardware

Boot Configuration

This item allows users to configure the default value of Numlock.

BIOS Setup

Option: On (default), Off

HDC Configuration

The host drive controller may be configured for IDE (legacy default), or AHCI mode.

When the legacy IDE mode is selected, the following screen will appear.

HDD Detect Delay Time

This setting allows you to configure the delaying time value before detecting the hard disks.

5-4

MPC-2190 Hardware

Option: 0 (default), 1, 2, 3 seconds.

Serial ATA Port 0 to 1

This setting allows you to display information about the installed drives.

BIOS Setup

AHCI SALP

Please note that AHCI SALP will only appear when AHCI mode is selected. This item allows you to enable

Aggressive Link Power Management (SALP) in AHCI. SALP enables the host bus adapter to conserve power by directly detecting when a SATA drive is no longer processing information and then immediately shifting it into suspended or sleep modes without waiting for software processes to initiate power-down processes.

Host Capability Register bit 26.

Options: Enabled (default), Disabled

SATA Port 0 to 1 - HotPlug

This item allows you to enable/disable hotplug capabilities (the ability to remove the drive while the computer is running) for installed storage drives.

Options: Disable (default), Enabled

Video Configuration

This item allows you to configure the integrated graphics device (IGD) for things like memory allocation (DVMT) and monitor types (Boot Type).

Internal Graphics Device

This option allows you to enable/disable the internal graphics device.

Options: Enable (default), Disable

5-5

MPC-2190 Hardware BIOS Setup

IGD—DVMT Pre-Allocated

This item allows you to configure pre-allocated memory capacity for the IGD. Pre-allocated graphics memory is invisible to the operating system.

Options: 64 MB (default), 32 MB, 96 MB, 128 MB, 256 MB, 512 MB

DVMT is a BIOS solution where “the optimum amount of memory is dynamically allocated and de-allocated as needed for balanced graphics and system performance, through Intel® Direct AGP and a highly efficient memory utilization scheme. DVMT ensures the most efficient use of available system memory resources for maximum 2D/3D graphics performance.

IGD—DVMT Size

This item allows you to configure the maximum amount of memory DVMT will use when allocating additional memory for the internal graphics device.

Options: 256 MB (default), 128 MB, Max

IGD – Boot Type

This item allows you to select the video device which will be activated during POST.

Options: VBIOS Default (default), VGA, DVI-D2, DVI-D1

5-6

MPC-2190 Hardware

Chipset Configuration

This item allows you to configure the chipset settings.

BIOS Setup

Power ON after Power Fail

This item allows you to enable/disable the computer form automatically powering up after a system crash.

Options: ON (default), OFF, Last State

5-7

MPC-2190 Hardware BIOS Setup

Hardware Monitor

This item allows you to view stats like CPU and system temperature, voltage levels, and other chipset information.

Security Settings

This section allows users to configure security settings with a supervisor password and user password.

5-8

MPC-2190 Hardware BIOS Setup

Set Supervisor Password

This item allows you set the supervisor password. Select and then enter the password, and then confirm the password again.

To delete the password, enter Set Supervisor Password and then enter the old password; then, leave the new password fields blank, and press enter.

Power Settings

The section allows users to configure power settings.

5-9

MPC-2190 Hardware

Boot Settings

The section allows users to configure boot settings.

BIOS Setup

Boot Type

This item allows you to enable/disable quick boot function.

Options: Dual Boot Type (default), Legacy Boot Type, UEFI Boot Type.

PXE Boot to LAN

This item allows you to enable/disable PXE boot to LAN function.

Options: Disabled (default), Enabled

Add Boot Options

This item allows you to add the boot order options for shell, network and Removables.

Options: Last (default), First

USB Boot

This item allows you to enable/disable USB boot function..

Options: Enabled (default), Disabled

EFI Device First

This item allows you to determine EFI device first or legacy device first. If enabled, EFI device will be the first; if disabled, legacy device will be the first.

5-10

MPC-2190 Hardware BIOS Setup

Options: Disabled (default), Enabled

Boot Delay Time

This item allows you to configure the delay time value for users to input hot key during POST time.

Options: 0 Second (default), 3 Seconds, 5 Seconds, 10 Seconds

Legacy

Normal Boot Menu

This item allows you to configure the boot menu.

Options: Normal (default), Advance

Boot Type Order

This item allows you to select the boot order. Use F5/F6 to change values.

Options: Hard Disk Drive (default), CD/DVD-ROM Drive, USB, Others

Hard Disk Drive/USB Drive

This item allows you to view installed devices such as hard disk drives, USB drives, or CD-ROMs. For example, if you have inserted a USB drive into the computer, it will appear here.

5-11

MPC-2190 Hardware

Exit Settings

The section allows users to exit the BIOS environment.

BIOS Setup

Exit Saving Changes

This item allows you to exit the BIOS environment and save the values you have just configured.

Options: Yes (default), No

Save Change Without Exit

This item allows you to save changes without exiting the BIOS environment.

Options: Yes (default), No

Exit Discarding Changes

This item allows you to exit without saving any changes that might have been made to the BIOS.

Options: Yes (default), No

Load Optimal Defaults

This item allows you to revert to the factory default BIOS values.

Options: Yes (default), No

Load Custom Defaults

This item allows you to load custom default values for the BIOS settings.

Options: Yes (default), No

5-12

MPC-2190 Hardware BIOS Setup

Save Custom Defaults

This item allows you to save the current BIOS values as a “custom default” that may be reverted to at any time by the “load custom defaults” selection just above.

Options: Yes (default), No

Discard Changes

This item allows you to discard all settings you have just configured.

Options: Yes (default), No

Upgrading the BIOS

This section describes how to upgrade the BIOS. However, please note that it is easy to permanently damage the computer when upgrading the BIOS. We strongly recommend that you contact Moxa’s technical support staff for assistance in order to obtain all necessary tools and the most current advice before attempting to upgrade the BIOS on any Moxa device.

Step 1: Create a Bootable USB Disk

Before upgrading the BIOS every user should first create a bootable USB RAM drive as a system rescue device.

You may use any software that can create a bootable USB drive. In this section, we use Rufus, which may then be downloaded and used to create a bootable RAM drive, as an example. Do the following steps to create a bootable USB disk by using Rufus.

1. Start the Rufus and in Device drop-down list select the

USB device that you want to use as a bootable disk.

2. Select MBR partition scheme for BIOS or UEFI

computers, let it can boot from legacy BIOS or UEFI.

3. Select FAT (Default) from File system drop-down list.

4. Select 16 kilobytes (Default) for Cluster size.

5. Enter a drive name in New volume label.

6. Check Quick format, Create a bootable disk using

FreeDOS, and Create extended label and icon

files.

7. Click Start to format and create the bootable USB drive.

ATTENTION

We suggest you use a USB drive with under 2 GB in disk space, as larger USB drives may not support FAT file format and consequently fail to boot.

5-13

MPC-2190 Hardware BIOS Setup

Step 2: Prepare the Upgrade File

You must use the BIOS upgrade installation file to upgrade the BIOS. Contact Moxa’s technical department for assistance.

1. Get the BIOS upgrade installation file. The file name should have following format: 200xxSx.exe (xx refers to version numbers).

2. Copy the file to the Bootable USB Disk.

Step 3: Run the upgrade program on the MPC-2190 Series Panel Computer

1. Reboot the computer, press F2 while booting up to go to the Boot Manager

2. Select USB Disk as the first boot source. Press Enter to continue.

3. When boot up finishes, DOS screen will show up. Go to the directory where the upgrade file is located. For example, if the upgrade file is stored in the MPC2190 folder, type cd MPC2190.

C:\cd MPC2190

4. Run the upgrade program by typing 20011S02.exe. Please note that the upgrade filename may vary depending on the versions.

C:\MPC2190>20011S02.exe

5. The upgrade program will be automatically performed. Please wait until the procedure to be finished.

5-14

MPC-2190 Hardware BIOS Setup

6. When the upgrade is finished, the computer will automatically reboot. You may check the BIOS version in

Main page of the BIOS Setup

ATTENTION

Do NOT switch off the power supply during the BIOS upgrade, since doing so may cause the system to crash.

5-15

6

6.

Display Control Interface

This chapter describes how to use the display’s control interface commands over the console.

The following topics are covered in this chapter:

Connecting to the Console Interface

Display Control Interface Command Format

Command Format Description

Downloading RGB Files

MPC-2190 Hardware Display Control Interface

Connecting to the Console Interface

If you want to use the commands in Appendix B to adjust the display settings, you need to connect to the display using the console interface. The following steps describe how.

The console interface is listed as the COM3 interface within the operating system. To communicate with the display over COM3, we suggest you use terminal emulator for Telnet, like Moxa’s PComm.

When launching the PComm Terminal Emulator, configure the following settings:

1. Select Port Manager, and then select Open.

2. Configure the Property settings:

Protocol: Serial

Serial Parameters: COM3

Baud rate: 9600

Data bits: 8

Parity: None

Stop bits: 1

RTS state: ON

DTR state: ON

When finished, click OK.

6-2

MPC-2190 Hardware

3. After successfully connecting, select the Send pattern tab.

Display Control Interface

Now you can enter a command in the HEX field, and click Start Send to send the command. For example, you may send 07FF5357490006, which queries the firmware version number (a scalar).

6-3

MPC-2190 Hardware Display Control Interface

You will now see the firmware version displayed in the terminal (1.0, in the screenshot above). For details about the available commands and how they are used, refer to Appendix B: Display Control Interface

Commands.

Display Control Interface Command Format

Each command conforms to the following packet structure:

Byte # 0

ATTN

1

ADDR

2,3,4

CMD

5

LEN

6

IHCHK

The minimal command size is 7 bytes, and the maximal command size is 82 bytes.

7, etc

DATA

7+LEN

IDCHK

Command Format Description

ATTN (Attention)

This byte is used to identify a start of command, and it can be one of three values:

ATTN Description

0x07

0x06

Command (ASCII BELL)

Acknowledge (ASCII ACK)

0x15

Negative Acknowledge (ASCII NAK)

A device shall send a command using the 0x07 Attention Code. The unit will respond to the command with either an ACK if the command completed successfully, or a NAK if the command failed.

6-4

MPC-2190 Hardware Display Control Interface

ADDR (Address)

This byte is used to specify a particular unit to receive a command and to identify the unit responding (ACK or NAK) to a command. Please note that MPC-2190 only supports broadcast address. The Address field shall have the following values:

ADDR

0xFF

Description

Broadcast - Addressed to all units

6-5

MPC-2190 Hardware Display Control Interface

CMD (Message Commands and Queries)

0x42

0x42

0x44

0x44

0x45

0x47

0x50

0x53

0x53

The command can be one of the following values. For details, refer to Appendix B: Display Control Interface

Commands.

CMD 0 CMD 1 CMD 2 ASCII Description

0x42

0x42

0x42

0x42

0x52

0x52

0x52

0x52

0x49

0x4C

0x4D

0x54

“BRI”

“BRL”

“BRM”

“BRT”

Brightness Minimum Value

Set LED Brightness of Touch Keypad

Brightness Maximum Value

User Brightness Control

0x41

0x41

0x42

0x44

0x45

0x52

0x5A

0x4C

0x4C

0x54

0x4D

0x4F

0x57

0x57

0x44

0x44

0x4C

0x55

0x4D

0x55

0x5A

0x4E

0x3F

0x43

0x42

0x54

0x49

0x4B

0x46

0x3F

0x49

0x46

0x53

“BRU”

“BZZ”

“DLN”

“DL?”

“ETC”

“GMB”

“POT”

“SWI”

“SWK”

“ADF”

“AD?”

“BLI”

“DUF”

“EMS”

Glass Display Control - Brilliance Button

Buzzer Control

Download ECDIS RGB package

ECDIS RGB package Query

Elapsed Time Counter Query

Glass Display Control - Minimum Brightness

Potentiometer Control

Scalar Firmware Version Query

Touch Keypad Firmware Version Query

AC Input Power Detect Function

Query AC Input Power Detect Function Status

Brightness Control

Disable UART Command Function

ECDIS Mode Select

LEN (Data Length)

This byte defines the length of data in the message in bytes. The maximal value for this field is 74 bytes, and the minimal value is 0 byte.

IHCHK (Inverse Header Checksum)

This is a simple 8-bit checksum of the header data, message bytes 0 to 5. The 8-bit sum (without carry) of bytes 0, 1, 2, 3, 4, 5, and 6 shall be 0xFF.

If a message is received with an incorrect checksum, the display will replay with the attention code set to NAK.

DATA (Data Field)

The data field shall only be transmitted if LEN is larger than 0. This field depends on the CMD transmitted.

IDCHK (Inverse Data Checksum)

These bytes shall be only transmitted if LEN is larger than 0. This is a simple 8-bit checksum of the data field, message bytes 7 to 7+ (LEN-1).

The 8-bit sum (without carry) of bytes 7 through 7+LEN inclusive shall be 0xFF. The receiver will reply to any message that the checksum has failed with the attention code set to NAK.

6-6

MPC-2190 Hardware Display Control Interface

Downloading RGB Files

Use the following commands for downloading RGB files.

Commands

DL?

DLN

Description

Data: none (0 byte)

ACK: Total packet numbers (1 byte)

Data: Appointed packet (1 byte)

ACK: File content (30 bytes maximum, except for the last packet)

The command DL? will send a request to the micro controller and ask how many packets that need to be downloaded. The reply from the micro controller shall be used when using the command DLN to download the specific packets. Refer to the following section for detailed descriptions of the DL? and DLN.

Command DL?

Byte

Number

Hex

ASCII

Byte 0

0x7

Command DLN

Byte 1

0xFF

Byte 2

0x44

D

Byte 3

0x4C

L

Byte 4

0x3F

?

Byte 5

0x0

Byte 6

0x2A

Byte

Number

Hex

ASCII

Byte 0

0x7

Byte 1

0xFF

Byte 2

0x44

D

Byte 3

0x4C

L

Byte 4

0x4E

N

Here is the example of downloading the RGB file package 0:

Command to read package 0.

0x07 0xFF 0x44 0x4C 0x4E 0x01 0x1A

ACK the package 0 of the first RGB file

0x06 0xFF 0x44 0x4C 0x4E 0x20

Data should be the real value of the RGB file package 0.

0xFC

Byte 5

0x1

0x00

0x00

0xFF

-

Byte 6

0x1A

Byte 7 Byte 8

0x50

Data

0xAF

IDCHK

6-7

A

A.

Regulatory Approval Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Class A: FCC Warning! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

European Community

Warning:

This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take compensatory measures.

B

B.

Display Control Interface Commands

This chapter defines the serial data format and the serial communication protocol so that engineers can use them to program the MPC-2190 panel computer..

This appendix explains how to use the display control interface commands.

The following topics are covered:

Display Control Interface Commands

BRI (Brightness Minimum Value)

BRL (Set LED Brightness of Touch Keypad)

BRM (Brightness Maximum Value)

BRT (User Brightness Control)

BRU (Glass Display Control-Brightness Button)

BZZ (Buzzer Control)

DLN (Download ECDIS RGB Package)

DL? (ECDIS RGB Package Query)

ETC (Elapsed Time Counter Query)

GMB (Glass Display Control - Minimum Brightness)

POT (Potentiometer Control)

SWI (Scalar Firmware Version Query)

SWK (Touch Keypad Firmware Version Query)

ADF (AC Input Power Detect Function)

AD? (Query AC Input Power Detect Function Status)

BLI (Brightness Control)

DUF (Disable UART Command Function)

EMS (ECDIS Mode Select)

MPC-2190 Hardware Display Control Interface Commands

Display Control Interface Commands

This section describes the display control interface commands that can be used to configure the display. See the following descriptions.

BRI (Brightness Minimum Value)

This command is to set the brightness minimum value. The range starts from 0x00 to 0x31 (0% - 100%).

LEN=one data byte.

Example:

Command to set 30% brightness.

0x07 0xFF 0x42 0x52 0x49 0x01 0x1B 0x10 0xEF

BRL (Set LED Brightness of Touch Keypad)

This command is to set led brightness value of touch keypad. The range starts from 0x00 to 0x31 (0% - 100%).

The default brightness value of the touch keypad will be changed in the ratio of the panel backlight brightness.

You can send ? to query the current value of the led brightness value. LEN=one data byte.

Example:

Command to set 100% Brightness.

0x07 0xFF 0x42 0x52 0x4C 0x01 0x18 0x31 0xCE

BRM (Brightness Maximum Value)

This command is to set the brightness maximum value. The range starts from 0x00 to 0xFF (0% - 100%).

LEN=one data byte.

Example:

Command to set 88% Brightness.

0x07 0xFF 0x42 0x52 0x4D 0x01 0x17 0xE0 0x1F

BRT (User Brightness Control)

This command is to set maximum brightness of the panel. The range starts from 0x00 to 0xFF (0% - 100%).

The default value is 0xFF.

Please note whenever the MPC-2190 has been restarted, the BRT value will be reset to 100%.If the BRT value has been changed (the BRT value does not equal to 0xff), the ECDIS function will not be supported and the

ECDIS function keys will be disabled and turned off.

If the data and data checksum of sending are incorrect, the data field of replying is the current BRT value.

LEN=one date byte.

Example:

Command to set 40% Brightness.

0x52 0x54 0x01 0x10 0x66 0x99 0x07 0xFF 0x42

ACK was set to 40% Brightness

0x06 0xFF 0x42 0x52 0x54 0x01 0x11 0x66 0x99

NAK was default Brightness 100%

0x15 0xFF 0x42 0x52 0x54 0x01 0x02 0xFF 0x00

BRU (Glass Display Control-Brightness Button)

This command is to set led brightness value of the touch keypad. The range starts from 0x00 to 0xFF (0% -

100%). The default brightness value of the touch keypad will be changed in the ratio of the panel backlight brightness.

B-2

MPC-2190 Hardware Display Control Interface Commands

You can send ? to query the current value of the led brightness value. LEN=one data byte.

Example:

Command to set 100% Brightness.

0x07 0xFF 0x42 0x52 0x55 0x01 0x0F 0xFF 0x00

BZZ (Buzzer Control)

The default value for the buzzer is OFF. Users can send this command to turn on/off the buzzer.

If the data and data checksum of sending are incorrect, the data field of replying is current buzzer status.

LEN=one byte.

0x00

0xFF

Turn the buzzer OFF

Turn the buzzer ON

Example:

Turn the buzzer ON.

0xFF 0x42 0x5A 0x5A 0x01 0x02 0xFF 0x00 0x07

ACK

0x06 0xFF 0x42 0x5A 0x5A 0x01 0x03 0xFF 0x00

DLN (Download ECDIS RGB Package)

Before sending this command, use DL? to know how many available packets in each ECDIS table. This command cannot be used if the MPC-2190 has not been calibrated. Every packet has a head (Byte 7 and Byte

8), Byte 7 is this packet number and Byte 8 is "-" with ASCII, and after the Bytes are data. If packet is full the data is Byte 9 to Byte 38. LEN=one date byte.

Data length is 32. The first byte is package num., the second byte is “-” and the other 30 byte is data.

Example:

Command to read package 0.

0x07 0xFF 0x44 0x4C

ACK the package 0 of the first RGB file

0x4E

0x06 0xFF 0x44 0x4C 0x4E

0x01

0x20

0x1A

0xFC

0x00

0x00

0xFF

- Data IDCHK

DL? (ECDIS RGB Package Query)

Use DL? to know how many available packets in each ECDIS table. This command cannot be used if the

MPC-2190 has not been calibrated. Total package num = Size of ECDIS RGB file/30 bytes per package.

Example:

Send DL? command to query total package num. of the first RGB file.

0x44 0x4C 0x3F 0x00 0x2A 0x07 0xFF

ACK 255 packages

0x06 0xFF 0x44 0x4C 0x3F 0x01 0x2A 0xFF 0x00

ETC (Elapsed Time Counter Query)

This command is to query the elapsed time that the MPC-2190 has been operated. The MCP-2190 will reply to this command with an ACK attention code. The largest byte will be transmitted first.

The maximum indicator for this function is 99999 hours (defined into 5 bytes, numbers 0 to 9 each), equivalent to 11 years. If this number is reached, the ETC will stop counting, and the ETC command will always reply with maximum number of hours (99999).

Example:

Send ETC to query elapsed time:

0x07 0xFF 0x45 0x54 0x43 0x00 0x1D

B-3

MPC-2190 Hardware Display Control Interface Commands

ACK 99999 hours

06 FF 45 54 43 05 19 39 39 39 39 39 E2

GMB (Glass Display Control - Minimum Brightness)

This command is to set the minimum value limit for the brightness of touch keypad LED to make sure that the

LED indicators are still visible if they was previously adjusted down to a very low value. The range starts from

0x00 to 0x31 (0% - 100%). LEN=one date byte.

Example:

Command to set 30% Brightness.

0x07 0xFF 0x47 0x4D 0x42 0x01 0x22 0x10 0xEF

POT (Potentiometer Control)

The BR+/BR- key default value is Enable. Users can send this command to disable/enable BR+/BR- key. If the data and data checksum of sending are incorrect, the data field of replying is current control status. LEN=one date byte.

0x00

0xFF

Example:

Brightness +/Brightness - Key Disable

Brightness +/Brightness - Key Enable

Disable the BR+/BR- Key.

0x07 0xFF 0x50

ACK

0x06 0xFF 0x50

0x4F

0x4F

0x54

0x54

0x01

0x01

0x05

0x06

0x00

0x00

0xFF

0xFF

SWI (Scalar Firmware Version Query)

This command is to query the scalar firmware version.

Example:

Query Scalar Firmware Version

0x07 0xFF 0x53 0x57 0x49 0x00 0x06

SWK (Touch Keypad Firmware Version Query)

This command is to query the touch keypad firmware version.

Example:

Query Touch Keypad Firmware Version

0x07 0xFF 0x53 0x57 0x4B 0x00 0x04

ADF (AC Input Power Detect Function)

This default value of this function is OFF. If the MPC-2190 supports AC power input, users can turn on this function to detect AC input power when the MPC-2190 has connected to the AC power. LEN=one date byte.

0x00 AC Input Power Detect is OFF

AC Input Power Detect is ON 0xFF

Example:

Set “OFF”.

0x07

ACK

0x06

0xFF

0xFF

0x41

0x41

0x44

0x44

0x46

0x46

0x01

0x01

0x2D

0x2E

0x00

0x00

0xFF

0xFF

B-4

MPC-2190 Hardware Display Control Interface Commands

AD? (Query AC Input Power Detect Function Status)

If the MPC-2190 supports AC power input, users can use command is to query AC Input Power Detect Function

Status.

0x00

0xFF

Example:

AC Input Power Detect is OFF

AC Input Power Detect is ON

Send AD? command to Query AC Input Power Detect Function Status

0x07

ACK

0xFF 0x41 0x44 0x3F

0x06 0xFF 0x41 0x44 0x3F 0x01 0x35

0x00

0x00

0x35

0xFF

BLI (Brightness Control)

This command is to set the panel brightness. Brightness range is from 0x00 to 0xFF. Default Brightness is 160.

LEN=one date byte.

Example:

Set brightness to 255(0xFF)

0x49 0x01 0x21 0xFF 0x00 0x07

ACK

0xFF 0x42

0x06 0xFF 0x42

Query current brightness value

0x07 0xFF 0x42

0x4C

0x4C 0x49

0x4C

0x01

0x49

0x22

0x00

0xFF 0x00

0x22

ACK

0x06 0xFF 0x42 0x4C 0x49 0x01 0x22 0xFF 0x00

DUF (Disable UART Command Function)

Users can use this command to disable related command control. LEN=one date byte.

DATA

0x00

IDCHK

0xFF

Function description

Disable all command control

0x01

0x02

0x04

0x08

0x10

0x20

0x40

Example:

0xFE

0xFD

0xFB

0xF7

0xEF

0xDF

0xBF

Disable BRI control

Disable BRL control

Disable BRM control

Disable BZZ control

Disable ETC control

Disable GMB control

Disable POT control

Disable all command control

0x07 0xFF 0x44

ACK

0x06 0xFF 0x44

NACK

0x15 0xFF 0x44

0x55

0x55

0x55

0x46

0x46

0x46

0x01

0x01

0x01

0x19

0x1A

0x0B

0x00

0x00

0x00

0xFF

0xFF

0xFF

EMS (ECDIS Mode Select)

For the ECDIS models, users can use this command to switch DAY, DUSK and NIGHT mode. LEN=one date byte.

DATA IDCHK

B-5

MPC-2190 Hardware

DAY

DUSK

NIGHT

Example:

Switch to DUSK mode

0x07

ACK

0xFF

0xFF 0x06

NACK

0x15 0xFF

0x45

0x45

0x45

0x00

0x01

0x02

0x4D

0x4D

0x4D

0x53

0x53

0x53

Display Control Interface Commands

0xFF

0xFE

0xFD

0x01

0x01

0x01

0x13

0x14

0x0B

0x01

0x01

0x01

0xFE

0xFE

0xFE

B-6

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents