Telstra T165i HSDPA Multi band 3G Mobile Phone User Manual

Telstra T165i HSDPA Multi band 3G Mobile Phone User Manual
Telstra T165i
HSDPA Multi band 3G Mobile Phone
User Manual
1
PC Software Requirements
Join Me PC Software included supports Microsoft Vista (only 32 bit), Windows 2000 with Service Pack 4 or
Windows XP with Service Pack 2 only. A limited version of Join Me is provided that supports MAC. 64 Bit
systems are NOT supported.
Warnings and Safety Notices
Please read all the safety notices in section 1.2 and 16 before using this device.
Copyright © 2008 ZTE Corporation All rights reserved.
2nd Edition November 2008
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE
Corporation.
ZTE Corporation operates a policy of continuous development. ZTE Corporation reserves the right to make
changes and improvements to any of the products described in this document without prior notice.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages
resulting from or arising out of or in connection with using this product, whether or not ZTE had been
advised, knew or should have known the possibility of such damages. The user should refer to the
enclosed warranty card for full warranty and service information.
2
RF Safety Information
The handset has an external antenna located at the top of the phone. For optimum performance with
minimum power consumption always extend the antenna during a call and do not cover the antenna
area with your hand. Hold the handset between thumb and finger in the middle of the device.
Covering the antenna affects call quality, may cause the handset to operate at higher power level
than needed, and may shorten talk and idle times.
Radio Frequency Energy
The handset is a low-power radio transmitter and receiver. When switched on it intermittently
transmits radio frequency (RF) energy (radio waves). The transmit power level is optimized for best
performance and automatically reduces when there is good quality reception. Maximum power is
only used at the edge of network coverage so under most circumstances the power output is very low.
Under poor network conditions the phone will transmit at a higher power, may get hot and will have
a significantly shorter battery life.
Declaration of Conformity
We declare under our sole responsibility that the product(s) detailed in this manual, and in
combination with our accessories, conform with the essential requirements of The Radio
Communications Standard (Electro-magnetic Radiation Human Exposure) 2003 and the Australian
Communications and Media Authority Section 376 of the Telecommunications Act 1997.
N14945
3
1
Contents
Welcome
1.1
1.2
1.3
1.4
1.5
2
17
Getting Started
2.1
2.2
2.3
2.4
2.5
2.6
2.7
3
How do I insert the USIM Card?
How do I insert the Battery?
How do I switch the phone On or Off?
How do I connect the charger?
Tips about charging and battery life
How do I set the time and date?
How do I lock the keypad?
4
How do I make a voice call?
How do I answer an incoming call?
How do I send a Text Message (SMS)?
How do I navigate the Menus?
21
21
21
22
23
Contacts
4.1
4.2
4.3
4.4
4.5
4.6
17
18
19
19
20
20
20
21
Basic Operation
3.1
3.2
3.3
3.4
9
10
11
13
14
15
How to use the manual
Handset Overview
Keypad Functions
Information Bar Icons
Menu Quick Reference Guide
How do I enter my Contacts?
How do I copy all Contacts from a USIM card?
How do I search my Contacts?
How do I add a Contact from a received call number?
How do I add a Contact from a received SMS (Text Message)?
How do I set a dedicated ringtone or image to a Contact?
4
23
23
23
24
24
24
4.7
4.8
4.9
4.10
5
How do I set Speed Dial numbers?
How do I make a call using Speed Dial?
How do I update an existing Contact?
Advanced Contact Options
27
Calls
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
5.17
6
How do I make a Voice Call?
How do I make a Voice Call from my Contacts?
How do I view and make a Voice Call from my Call History?
Call options during an active Voice Call
How do I activate Speakerphone?
How do I answer a Call?
How do I make a Video Call?
Call options during an active Video Call
How do I answer a Video Call?
How do I make Emergency Calls?
Videophone Setting
Call Divert
Call Waiting
Call Barring
Send my number
Missed Calls Alert
Call Options when Connected to a Bluetooth device
27
27
27
28
28
29
29
30
30
31
32
32
32
33
33
34
34
35
Messages and Emails
6.1
6.2
6.3
6.4
25
25
25
26
How do I send a Text Message (SMS)?
How do I view a received Text Message (SMS)?
How do I use Predictive Text?
How do I add words to the built in Dictionary (My Words)?
5
35
35
36
37
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
7
Special Characters and SMS Message Length
How do I send a Multimedia Message (MMS)?
How do I receive a Multimedia Message (MMS)?
MMS Settings
WAP Push Messages
How do I send an Email?
How do I receive an Email?
How do I set up automatic Email Retrieval?
Pushmail Settings
41
How to Personalise the Phone
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
8
Change the Profiles
Change the Shortcut Keys (Arrow keys)
Change the Background Screen (Wallpaper)
Change the default Ringtones
Enable Vibrate Mode
Engage Meeting Mode with a single key press
Switch the Keytones off
Change the Screen Brightness
Change the Display Backlighting
Set the Keypad backlighting
Add a Greeting and Owner name
What is the PIN Code?
What is the Handset Code?
Additional notes on PIN Codes
41
42
42
43
43
43
43
44
44
44
44
45
45
45
46
File Manager and External Memory
8.1
8.2
37
38
38
38
39
39
40
40
40
File Manager
Installing Additional Memory - microSD card
6
46
47
8.3
8.4
9
Access the T-Flash card (microSD) using File Manager
File Manager and T-Flash Options Table
10
Set Alarms
Set Appointments using the Calendar
12
13
51
52
53
How to use the Camera
How to use the Video Camera
Viewing pictures and videos
54
Music
11.1
11.2
11.3
FM Radio
Browse and play music files from File Manager
Create a new Playlist
54
54
55
56
57
Assisted-GPS
Connectivity
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
13.10
13.11
13.12
49
50
51
Imaging - Pictures and Videos
10.1
10.2
10.3
11
49
Alarms and Appointments
9.1
9.2
48
48
Use Join Me to connect the phone to a computer
Installing Join Me
Use Join Me to copy photos to your computer
Use Join Me to transfer music from a computer
Enter Contacts using Join Me
Copy Contacts from the phone to the computer
Import Contacts from Microsoft Outlook
Import Calendar events from Microsoft Outlook
Use Join Me to connect to the Internet
Connect to a Bluetooth Device
Dial Up Networking using USB or Bluetooth
PC Connection
7
57
58
59
61
63
64
65
66
66
67
69
71
13.13
14
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
14.9
14.10
14.11
14.12
14.13
14.14
14.15
14.16
14.17
15
71
72
72
73
73
73
74
74
74
75
75
75
75
76
76
76
77
77
78
Browser
Stopwatch
Calculator
World Time
Currency Conversion
PocketNews
Games and Applications
Voice Recorder
Slide Show
Streaming URL
Connections
Access Point Settings
Restore default settings
Auto Keylock
Download Location
Network Settings
CTM
Technical, Support and Warranty Information
15.1
15.2
15.3
15.4
15.5
16
17
Synchronize with a network server (SyncML)
Other Facilities
79
79
81
82
83
83
Troubleshooting and FAQ’s
Error Messages
Technical Parameters
Support Information
Warranty Information
Environmental Statement
General Safety and Maintenance Information
8
84
85
1
Welcome
Congratulations on choosing the Telstra T165i handset. Please take a few minutes to read the
user guide to help you get the most from your new mobile phone
Operation
Quick Reference
Handset overview, keypad and information bar
Section 1 – Introduction
Making a call
Section 2 – Getting Started
Quick introduction to key features, Calls and SMS
Section 3 – Basic Operation
Store a list of contact names and phone numbers
Section 4 – Contacts
View calls received, dialled and missed
Section 5 – Calls
Text messages – sending and receiving
Section 6 – Messages and Emails
Personalise your phone, e.g. ringtone, screen saver
Section 7 – Personalise
Managing handset files and content
Section 8 – File Manager
Setting alarms and reminders
Section 9 – Alarms and Appointments
Using the camera – take photos, record a video
Section 10 – Imaging
FM radio, MP3’s and access to music libraries
Section 11 – Music
Using GPS
Section 12 – Assisted GPS
Connecting to a PC to copy pictures and music
Section 13 – Connectivity
Calculator, Stopwatch and more
Section 14 – Other Facilities
Accessing the internet, BigPond, Whereis®, etc
See your Telstra Next G guide
9
1.1
How to use the manual
The following conventions are used in the manual:
Instruction
Press the Left Arrow ◄
Press OK
Press the Right Soft Key
Long press
Menu > Tools
•
•
•
•
•
Description
Press the left directional key on the four way controller
Press the OK key in the centre of the four way controller
Press the
key just below the screen.
Press and hold the key for 2 seconds.
Go to the Main Menu (press OK) select Tools and press OK to open
The functions for the OK and Soft keys change depending on where you are in the menu.
The functions are always described at the bottom of the handset display.
The End or Exit key
is used to exit the menus, end a Call and switch the handset On or
Off. From within a sub-menu the Exit key takes you back to the main menu
Long press the
key to switch the handset On and Off.
The C key is used to go back one step in menus, and to clear text in text edit modes. In text
edit mode press once for backspace, press and hold to clear all the text.
The
symbol shows useful tips.
Menu and setting choices on the handset are shown in bold grey text in the manual.
Quickly find the answer to any question you may have, check the Contents at the front
of the manual or visit the Index at the back of the manual.
There is a copy of the manual and quick start guide provided on your CD
10
1.2
Handset Overview
1. Extendable Antenna
2. Earpiece
3. Four way controller Arrow Keys(◄►▲▼)
4. Left Soft Key (LSK)
5. Call Key, show Call History
6. Video Call Key
7. Keypad
8. Microphone
9. Clear Key *
10. End / Exit / Power Key
11. Right Soft Key (RSK)
12. OK Key
13. Camera for video calling
1
2
13
3
12
4
5
6
11
10
9
* The C key is used to go back one step in menus, 7
and to clear text in text edit modes.
In text modes press once for backspace,
press and hold to clear all the text.
8
11
Handset Overview
External Antenna port
(must be open for
car-kit insertion)
Speaker
Camera
Volume keys
microSD Port
Charger / USB /
Headset port
(Slide to open)
Camera key
Left
Rear
12
Right
1.3
Key
Keypad Functions
Corresponding Functions
1
1 | punctuation marks | voicemail
2
2 | abc | ABC
3
3 | def | DEF
4
4 | ghi | GHI
5
5 | jkl | JKL
6
6 | mno | MNO
7
7 | pqrs | PQRS
8
8 | tuv | TUV
9
9 | wxyz | WXYZ
0
0 | Space
Key
Corresponding Functions
Long press for keylock
*
Special characters in text modes
Press twice for the international prefix ‘+’
Press three times for the pause character ‘P’
#
Call
Toggle text modes. Long press for Silent
Open All Calls list
Call a dialled or selected number
End
End a call.
Exit a menu
Long press to power ON / OFF
13
1.4
Information Bar Icons
3G Signal Strength
Battery Level Indicator
GSM Signal Strength
Alarm is set
Signal Strength of the EDGE Network
Missed Call
New SMS or MMS Message
Missed Video Call
SMS or MMS Memory is Full
Silent Mode
New E-mail
Vibrate mode enabled
E-mail Memory is Full
Call Forward is Active
New Wap Push Message
GPRS Attach
Wap Push Message Memory is Full
PDP Context Established (Data)
Headset and Vibrate Mode
High speed data, HSDPA mode
Headset Mode
Roaming
Bluetooth is ON
Car kit attached
A-GPS is ON
14
1.5
Menu Quick Reference Guide
1) BigPond
2) Messages
1 New Message
2 Inbox (0/0)
3 Outbox (0)
4 Drafts (0)
5 Sent (0)
6 User folders
7 (U)SIM Inbox
8 Settings
9 Memory info.
4) Camera
3) Calls
> E-mail
1 New Email
2 Inbox (0/0)
3 Outbox (0)
4 Drafts (0)
5 Sent (0)
6 User folders
7 Settings
A. Call log
1 All calls
2 Missed calls
3 Received calls
4 Dialled calls
>
B. Calls Info.
Call duration
8 Memory info.
5) My Place
6) Multimedia
7) STK (SIM Tool Kit)
1 BigPond
1 Camera
Pocket News
2 FOXTEL
2 Video camera
> My Favorites
3 Yellow
3 FM Radio
> News
4 Scan Code
4 Media player
5 My Email
5 Playlist
6 Call 1234
6 Slide show
7 Music
7 Streaming URL
8 Whereis
8 Voice recorder
9 Blog&Photo
9 Games & Apps
10 Downloads
11 My Account
15
> Finance
> Weather
> Horoscope
> Sport Scores
> Surf Report
8) Contacts
All
> USIM
> Family
> Friends
> Work
> VIP
> Unclassified
#) Settings
A. Screen
1 Wallpaper
2 Display Backlighting
3 Set brightness
4 Keypad Backlighting
5 Owner name
6 Greeting
*)Calendar
9) Tools
1 Browser
2 Alarm
3 Stopwatch
4 Calculator
5 World Time
6 Bluetooth
7 Syncml
8 Currency Conversion
9 GPS
B. Handset
1 Language
2 Time and date
3 Network settings
4 Own phone number
5 Shortcut keys
6 Connections
7 Access point settings
8 Restore default settings
9 Keylock
10 Network time
11 Download location
12 PC Connection
13 CTM
14 Missed calls alert
0) File Manager
Photos
View appointments.
Audios
Add a
Videos
Meeting
Others
Memo or
Reminder
> TFlash Card
C. Profiles
E. Call
1 General
1 Videophone settings
2 Meeting
2 Call divert
3 Outdoor
3 Call waiting
4 Silent
4 Call barring
5 Car kit
5 Send my number
D. Security
1 Activate security codes
2 Change security codes
3 Fixed dial numbers
4 FDN list
16
2
2.1
Getting Started
How do I insert the USIM Card?
The USIM card (UMTS Subscriber Interface Module) is the small plastic smart-card with gold contacts.
It holds personal information such as names and phone numbers. It can be moved between different
phones if required. The USIM card must be inserted before using the handset.
•
Insert the USIM card with the gold contacts facing down and the bevelled edge on the left hand
side as shown. Carefully slide it under the metal bar observing the correct orientation.
If your handset displays: “No (U)SIM detected” please check the USIM is inserted correctly.
“Enter PUK code” please contact your Service Provider.
“Enter Unlock code” please contact your Service Provider.
17
2.2
How do I insert the Battery?
Insert the battery as shown with the contacts located against the gold springs. The battery will only
fit one way.
Close the case by locating the plastic cover horizontally into the grooves and sliding the cover up to
close it. Do NOT force the cover down by pressing on it. This can damage the cover.
Slide the cover up gently
Locate the cover into the grooves horizontally and slide up gently.
18
2.3
How do I switch the phone On or Off?
Press and hold the
key for two seconds to switch the phone ON or OFF.
The start up screen below is referred to throughout the manual as the Idle Screen:
The Information bar
The Idle Screen
2.4
How do I connect the charger?
Slide the charger port to open. Charge before initial use. The charger lead only fits one way. The plug is
marked with an arrow. Always insert the charger lead carefully with the arrow facing the top of the
phone as shown:
Do NOT use excessive force which may damage the USB socket.
Physical damage to the USB port is NOT covered by warranty.
The phone can also be charged by connecting it to a
computer using the USB lead supplied.
If the phone is off after charging long press the End
19
Key to switch it back on.
2.5
Tips about charging and battery life
• Only use the AC charger and USB lead supplied.
• Insert the charger lead carefully with the arrow facing the top of the phone.
• Normal charge time is 2-3 hours. Do not leave on charge for more than 24hrs
• When not using the phone for long periods remove the battery.
• Charge the battery between 0°C~50°C. Charge the battery promptly when flat.
• With poor network conditions (less than 2 bars) battery life is reduced.
• To maximize battery life turn off Bluetooth when not in use and limit multimedia functions.
• The phone can be charged in the ON or OFF state. When the phone is OFF you will see the Charging
Battery animation. When the phone is ON the battery icon will animate.
• If charging in the OFF state turn the phone ON by long pressing the
2.6
key.
How do I set the time and date?
The time and date is set automatically from the network. It takes a few seconds to update when the
phone is first switched on. Select 12 or 24 hr format in the Network Time menu. To manually set the
time it is necessary to switch Network Time off: Menu > Settings > Handset > Network Time > State Off
then set the time and date manually: Menu > Settings > Handset > Time and date.
2.7
How do I lock the keypad?
Manual keylock: Long press the * key then press the right soft key to engage or disengage keylock.
Auto keylock: Menu > Settings > Handset > Keylock Set your desired time to lock the keypad. See 14.14.
20
3
Basic Operation
How do I make a voice call?
3.1
• Enter the number on the keypad and press the
key to make the call.
• Press OK to activate Handsfree (speakerphone) mode
• Press the
key to end the call.
How do I answer an incoming call?
3.2
• Press
or OK to answer the call.
• Press
or Reject to end the call.
If Voicemail is active pressing Reject will forward the call to Voicemail.
3.3
How do I send a Text Message (SMS)?
• Press the Right Arrow ► for Messages
• Press OK for New Message. Press OK for Text Message
• Enter the phone number directly or press OK to select from Contacts
• Select the Contact then press OK for Done. The Contact number will be displayed, press OK
• Press the Down Arrow ▼ twice to move the cursor into the text field
• Type the message using the letter keys on the keypad (see Chapter 6 on Texting)
• Press the OK to send the message.
21
3.4
How do I navigate the Menus?
The Main Menu is a grid of icons that are used to access key features on the phone.
From the Idle Screen press OK to access the Main Menu. Use the Arrow Keys ▲▼◄►to move to the
desired icon. The icons are described at the bottom of the screen.
OK
Shortcuts
From the idle screen the Arrow Keys launch the Shortcuts as shown:
My Place
Email
Messages
Contacts
To change default shortcuts: Menu > Settings > tab right to Handset > Shortcut keys
From sleep mode (dark screen) press the key once to wake up the handset, press the key again
to perform the required function.
Use the number keys to select icons from the grid. ie Press Menu > 1 to select BigPond
22
4
4.1
•
•
•
•
Contacts
How do I enter my Contacts?
From the Idle Screen enter the phone number on the keypad, press the Left Soft Key to Save.
Press OK to create a New Contact or press the Down Arrow ▼to Update existing contact
Using the keypad, enter a name for the new Contact or modify an existing contact
Press OK to Save. The default save location is the USIM card. Change if required.
4.2
How do I copy all Contacts from a USIM card?
All USIM Contacts are automatically read by the handset.
To copy Contacts into the handset memory follow the steps below:
• Insert the USIM card you wish to copy contacts from. Switch the phone on.
• From the idle screen press the Down Arrow ▼ for Contacts.
• Press the Right Arrow ►once for USIM to show the list of Contacts on the USIM card.
• Press the Left Soft Key for Options then use the arrow keys to select, Copy > Copy all > OK > Yes to
confirm.
4.3
How do I search my Contacts?
From the idle screen press the Down Arrow ▼ for Contacts. To find the Contact ‘John’ press the 5 key
once for ‘J’. All names starting with ‘J’ will be displayed.
Refine the search by entering a subsequent letter that can occur anywhere in the name.
Eg. ‘Jn’ will find ‘John’ and ‘Julian’ but not ‘James’ whereas ‘Ja’ will find Julian and James but not John
23
4.4
How do I add a Contact from a received call number?
After receiving a call you can add the caller’s number to the Contacts list:
• Press the
key to display All Calls
• The last call received will be at the top of the list
• Press the Left Soft Key > Options > Save > New Contact or Update to modify a contact > OK
• Enter or modify the contact details and press OK to Save.
4.5
How do I add a Contact from a received SMS (Text Message)?
Menu > Messages > Inbox
• Select the required message and press OK to View
• Press Options > Use highlight object to save the number
• Choose New Contact to create a new contact from the received SMS number.
4.6
How do I set a dedicated ringtone or image to a Contact?
The contact needs to be stored on the handset in order to set a dedicated ring or image. See 4.2
Menu > Contacts (Shortcut = Down Arrow ▼)
• Use the arrow keys ▼▲ to find the required contact (must be stored on the handset)
• Press OK to View > Edit > Options > Add ring and photo. Select the required feature
• Press Add then navigate to the folder where the Ringtone or Picture is stored.
• Press OK to Save your choices when complete
24
4.7
How do I set Speed Dial numbers?
Having Speed Dials set makes it quicker to call selected contacts.
Menu > Contacts > Select the Contact > Options > Scroll down ▼ > Set Speed Dial > Setup
• Assign the chosen contact to the next available number
• Speed dials 1, 2 and 3 are preset and cannot be changed
• Press the OK Key to Setup the speed dial or press OK Key again to cancel
• Press the
4.8
key to exit when finished.
How do I make a call using Speed Dial?
• From the Idle screen press and hold the required number key to call that Contact
• E.g. A long press on the 1 key will automatically dial the Voicemail service.
4.9
How do I update an existing Contact?
• Edit the existing contact: Menu > Contacts > View > Edit. Press Save when finished
• Contacts are normally stored in the default Group, All
• You can move contacts into other Groups: Family, Friends, Work, and VIP.
• Search for a contact by pressing the letter keys that correspond to the contact name
• Refine the search by entering a subsequent letter that can occur anywhere in the name.
Eg. ‘Jn’ will find ‘John’ and ‘Julian’ but not ‘James’; ‘Ja’ will find Julian and James but not John
25
4.10
Advanced Contact Options
Menu > Contacts > Options
Option
Description or subsequent options
Call
Make a Voice Call or Video Call to the selected contact
Send
Send an SMS, MMS or E-mail to the selected contact
New Contact
Create a new contact
Edit Contact
Edit the selected contact
Delete
Delete contact, Delete all (Phone), Delete all (USIM), Delete all (Both)
Copy
Copy to phone, Copy all
Send Bus. Card
Send a business card via SMS, MMS, E-mail or Bluetooth
Default Memory
Default save location for contacts, USIM card or Phone
Service Dial number
Preset Voicemail and Video-mail message bank numbers
Speed dial
Assign a speed dial to the selected contact
Manage Contact
Set Group parameters (eg Ringtone and photo), Speed dial info and check
the memory status
26
Calls
5
5.1
How do I make a Voice Call?
• Enter the number on the keypad and press the
key to make a voice call.
• Press OK to activate Handsfree or Speakerphone (Loudsp.)
• Press the
5.2
key to end the call.
How do I make a Voice Call from my Contacts?
• Press the Down Arrow ▼(default shortcut) for the Contacts menu.
• Use the Arrow Keys ▼▲ to scroll to the chosen contact.
• Search Contacts using the letter keys – eg. press ‘J’ to find John
• Press the
key to make the call.
• Press the
key to end the call.
5.3
How do I view and make a Voice Call from my Call History?
• Press the
key to bring up All Calls. Press
again for Last Number Redial
• Use the Arrow Keys ▼▲ to choose a number from the All calls list
• Press the
key to make the call.
• Press the
key to end the call.
27
5.4
Call options during an active Voice Call
Press the Left Soft Key for Options during a voice call. Use the End key to return to the call menu
Hold:
End call:
Record:
DTMF Off/On:
Message:
Contacts:
Browser:
5.5
Puts the current call on hold
End the call
Record the current call. The audio file is saved to the My Audios folder
Enable or disable sending DTMF tones. Default is ON
Switch to SMS interface during a call
Switch to Contacts interface during a call
Launch the web browser
How do I activate Speakerphone?
Handsfree or Speakerphone is activated by pressing OK (Loudsp.) during a call
• To dial an International number press the star key twice for the International Prefix ‘+’
• To call a number received within a message highlight the number then press the Call key
• The microphone is on the base of the handset. Be careful not to block it with your hands
• During a call change the volume using the side Volume keys
• The number of rings before the phone diverts to Voicemail is set by your Service Provider.
The default is 6 rings. Contact your Service Provider to change this setting.
• To enable international roaming please contact your Service Provider.
28
5.6
How do I answer a Call?
When you receive an incoming call:
• The phone will light up, the call alert will sound and the phone will vibrate depending on the
current profile setting.
• You will receive an incoming call notification displayed on the screen
• Press
or OK to initiate Speakerphone (Loudsp.) to answer the call.
to Reject the call.
• Press
• Press Silence to mute the incoming ring if required. This feature is useful to silence the incoming
ring without answering the call. The other party hears ring tone until the call ends.
5.7
How do I make a Video Call?
3G coverage is required to make and receive video calls.
• Enter the phone number using the keypad or from the Contacts list as already described
• Press
• Press
to make a video call.
to end the call.
If the call is not successful you will be asked if you want to try a voice call instead.
29
5.8
Call options during an active Video Call
Press the Left Soft Key for the following Options during a video call:
Hold / Retrieve
Send a still picture instead of your own image and the voice is muted
Start recording video
Record video from the other party (i.e. received video stream)
Block/Send my picture
Block / Send your own image to the other party
Use back/front camera
Select the back/front camera
Brightness
Adjust the brightness
Zoom
Change the magnification of your own image
PIP off / on
Hide or show your own picture on the local screen
Exchange PIP
Reverses the Picture in Picture display, ie. the initiator of the call will
now appear larger
New text message
Send SMS during a video call
Contacts
Switch to Contacts interface
5.9
How do I answer a Video Call?
3G coverage is required to make and receive video calls. If a video call is received when browsing or
using multimedia functions, the browser, media player or FM radio will be suspended.
When receiving an incoming Video call:
• When receiving an incoming video call the phone will ring, vibrate and illuminate depending on the
current profile setting,
• Press the Video call key to accept the video call,
• Press the End key to end the video call.
30
5.10
How do I make Emergency Calls?
To make an emergency call during normal use
•
Ensure that the handset is switched on and in service.
•
Press the
•
•
Enter the emergency number for the present location using the keypad, (eg 000).
Press the
key to call the number. Follow instructions received and do not end the call until
told to do so.
If the keypad is locked it is possible to dial the Emergency Numbers without having to unlock the
keypad. Press the numbers as required then press the Call key.
•
key repeatedly to return to the Idle Screen.
Emergency calls can be made without a USIM Card (Phone PIN not required)
When the USIM card is not inserted or registered it is possible to dial the emergency services.
Enter the emergency number and press
or OK to make the call.
• Advise the operator which emergency service you require
• Give your position and remain stationary to get the best coverage
• Due to the nature of the cellular system the connection of emergency calls cannot be
guaranteed
• Never rely solely on any wireless device for essential communications ie. medical emergencies
• The Emergency Number 112 is used internationally.
31
Advanced Call Settings
5.11
Videophone Setting
Menu > Settings > tab right to Call > Videophone settings
All the fields are preset by your Service Provider. If you change Service Providers you may need to
update these settings. Contact your Service Provider for more details.
5.12
Call Divert
Menu > Settings > tab right to Call > Call divert
This service enables incoming calls to be diverted to another number. Choose the Call divert function
required from the menu list. From the functions listed select the feature you wish to Activate,
Deactivate or Check status.
5.13
Call Waiting
Menu > Settings > tab right to Call > Call Waiting
This feature allows an incoming call to be answered while already on a call. Answering the incoming
call will automatically place the first call on hold. The handset displays a table showing the Active call
and call on Hold. Pressing Options allows the switching between the ‘Active’ and ‘Hold’ calls.
Press Options to switch calls between Hold and Active:
03991234xx
Active
Press Options > Hold to switch calls
03996543xx
Hold
Press Options > Active to switch calls
32
5.14
Call Barring
Menu > Settings > tab right to Call > Call barring
Call barring is a network feature. The barring password is provided by your service provider. The service
needs to be enabled on your account. To obtain your PIN number contact your Service Provider.
Bar all outgoing calls:
Calls cannot be made.
Bar outgoing calls (international):
International calls cannot be made.
Outgoing International Calls except
for calls to the home country
Restricts international calls except to your home country
Bar all incoming calls:
Calls cannot be received.
Bar incoming calls when roaming
Calls cannot be received when you are overseas
Cancel all call barring
Cancels all barring settings
Change password
Set password to activate or erase call barring.
5.15
Send my number
Menu > Settings > tab right to Call > Send my number
Send or hide your number when making calls. Switch it on or off. The default set by the network is On.
33
5.16
Missed Calls Alert
Menu > Settings > tab right to Handset > Missed calls alert
After missing a call, the missed call icon
will be displayed on the information bar.
When the Missed call alert is set the reminder tones will sound at your specified interval for 5 times or
until the on screen message is acknowledged.
to display the All Calls list.
After a missed call press the green call key
Press the green call key
again to dial the last number.
5.17
Call Options when Connected to a Bluetooth device
If the handset is connected to a Bluetooth accessory such as a car kit or a wireless headset then an
incoming call is forwarded to the Bluetooth device. Press the Call key on the Bluetooth device to
answer the call. When idle press the call key on the Bluetooth device to initiate Last Number Redial on
the handset. The handset does not support Contacts over Bluetooth. See Section 13.10 for more details
An active call can be switched between the Bluetooth device and the handset by pressing:
Options > Switch to Handset / Switch to Bluetooth.
34
6
6.1
Messages and Emails
How do I send a Text Message (SMS)?
Right Arrow ►New Message > Text Message or
Menu > Messages > New Message > Text Message
• Press the OK Key to select from Contacts (Cont.) or enter the number manually.
• Scroll to the chosen contact and press OK twice (once to select and once to confirm)
• Press the Down Arrow ▼ twice (once to add extra contacts, once again to enter the text area)
• The default text mode is Predictive Text indicated by the En symbol
• Enter text by pressing the corresponding keys once for each required letter eg. 43556 for ‘hello’. The
system updates the display to show the most probable entry. See Section 6.3 for more details.
• Select the desired word from the available list and press OK to confirm or choose Spell Word? to add
a new word to the My Words dictionary.
• Press Options for the My Words dictionary
• Press the # key to toggle between En, 123, ABC and abc text modes.
• When completed press the OK Key to Send the message.
6.2
How do I view a received Text Message (SMS)?
• The envelope icon
will appear on the information bar to indicate a received message. The
message alert tone and vibrate activate depending on the current profile setting. Press OK to View
the message.
• Navigate to the Inbox (Menu > Messages > Inbox > OK to Select) to view all received messages.
Scroll to the desired message and press OK to View.
35
6.3
How do I use Predictive Text?
Predictive text allows words to be entered more efficiently using a single keypress for each letter, as
opposed to multiple keypresses in multi-tap text mode. Compare how to write the word ‘the’:
Traditional multi-tap text mode (ABC, abc)
Press 8 (tuv) once to select ‘t’
Press 4 (ghi) twice to select ‘h’
Press 3 (def) twice to select ‘e’
•
•
•
•
•
•
•
•
•
•
•
•
Predictive Text Mode (En)
Press 8 once for ‘t’
Press 4 once for ‘h’
Press 3 once for ‘e’
The default text mode is predictive text indicated by En in the top right corner of the display.
Press the # key to toggle between different modes En, abc, ABC, 123
It is not possible to disable predictive text mode or to change the initial mode
Predictive text uses a built-in dictionary to generate words from the sequence of letters pressed.
When a word is highlighted press the C key to delete the word, press the # key to change to capitals
as follows: dave, Dave, DAVE
Select the desired word from the available list using the ▲▼keys and press OK to confirm or
choose Spell Word? to save to My Words (See 6.4). Unknown words default to Spell Word?
If the next letter is on the same key, wait until the cursor appears or press the Right arrow ►to
move the cursor on
To insert a space press the 0 key. Press the C key once to delete single letters, hold to clear all text
Press the 1 key for common punctuation marks. Press the * key for special characters
ABC, abc are multi tap modes. Press the key once for the first letter, twice for the second letter etc.
In text input screens (eg SMS, MMS and E-Mail) you can add your own words to the built-in
Dictionary which is called My Words
Press the Options key to access My Words to Add new words to the available lists.
36
6.4
•
•
•
•
•
How do I add words to the built in Dictionary (My Words)?
From predictive text mode enter words directly by choosing Spell Word?
From the text entry screen press the Options key and select My Words
The first time you use My Words press OK to Add a new word
Type the new word using the ABC or abc modes then press OK to Save it
In My Words you can press the Options key to Edit, Delete or Delete all words.
6.5
Special Characters and SMS Message Length
The underlined characters in the above chart are Unicode Characters. This means that they are not
part of the standard SMS character set and they require 2 SMS characters to transmit them. Normal
SMS message length is 160 characters. If exceeded, the message will be sent by two SMS’. When the
underlined characters are used the message length is limited to 70 characters. When 70 characters is
exceeded the message is sent by two SMS’.
37
6.6
How do I send a Multimedia Message (MMS)?
Use a Multimedia Message to send pictures, music or video files to your friends.
Menu > Messages > New Message > Multimedia Message
•
•
•
•
•
•
Enter the phone number or press OK for Contacts to select a number
Press the down arrow ▼and enter text in the title field (if required)
Press the down arrow ▼to enter the text area (main message body)
From the text area press OK to Insert an Image, Audio or Video file
Browse the folders to select the required file. Press OK
When finished press the Right Soft Key to Send
Each ‘page’ can only contain one image, one audio, and one video file. To add more than one
file of the same type, select Options to add a new page.
6.7
How do I receive a Multimedia Message (MMS)?
Menu > Messages > Inbox
• When receiving an MMS you get a standard message alert. Press OK to View.
• Press Retrieve to download the message attachment.
• When the attachment has downloaded press the Left Soft Key for Options.
• Choose Use Highlight Object to Save the file into File Manager
6.8
MMS Settings
Menu > Messages > ▼ Settings > Mul. Msg. Settings
The MMS settings are preset by your Service Provider. If using an alternate Service Provider the MMS
Settings will need to be modified.
38
6.9
WAP Push Messages
Menu > Messages > ▼ Settings > Mul. Msg Settings > Push Messages – Accept or Reject
A WAP push message is a formatted SMS that displays a message to the user, giving the option of
connecting directly to a particular URL via the mobile phone’s WAP browser.
• WAP Push Messages are indicated by the
Icon on the main display.
• Use the Browser to view Push Messages. Set to Reject to disable Push Messages
6.10
How do I send an Email?
Menu > Messages > tab right to Email > Settings > Mailbox Settings > Options > Edit
• The default Email client is configured for BigPond
• Add your BigPond username, password and email address
• The username should be the full address: [email protected]
• It is possible to Add other providers under Mailbox Settings
• Configure the POP Server details, SSL settings, IP Address etc. by reference to the other provider.
Sending an Email
Menu > Messages > tab right to Email > New E-mail
• Enter the sender address e.g. [email protected]
• Press the down arrow ▼ to access the Copy To Field
• Press the down arrow ▼ to access the Title Field
• Press the down arrow ▼ to enter the Text Field
• Press OK to Insert attachments if required
• Browse to the appropriate folder to add the attachment
• When you are finished press the Right Soft Key to Send.
39
6.11
How do I receive an Email?
Configure the Email Client with your personal settings to enable receiving Emails.
Menu > Messages > tab right to Email > Settings > Mailbox Settings > Options > Edit
• The default Email client is configured for BigPond
• Add your BigPond username, password and email address
• The username should be the full address: [email protected]
• It is possible to Add other providers under Mailbox Settings
• Configure the POP Server details, SSL settings, IP Address etc. by reference to the other provider.
Send an SMS, MMS or Email to up to 10 recipients
Receiving an Email
Menu > Messages > tab right to Email > Inbox > Options > Retrieve
New Email messages will be delivered to the handset
6.12
How do I set up automatic Email Retrieval?
Menu > Messages > tab right to Email > Settings > Automatic Retrieval
Set your required polling time interval to check the server for new Email messages.
6.13
Pushmail Settings
Menu > Messages > tab right to E-mail > Settings > Pushmail Settings > Receive Pushmail
Pushmail denotes an automatic email retrieval service that is Always On. New emails arriving on your
server are ‘pushed’ to your handset. This feature depends on network support and it is not provided
automatically by a POP3 server.
40
7
How to Personalise the Phone
There are many ways to customise the handset such as changing the profiles, wallpaper, ringtones,
setting up shortcuts etc.
7.1
Change the Profiles
Menu > Settings > tab right to Profiles > Edit the required Profile
From the idle screen long press the # key to engage Meeting Mode (silent with vibrate)
Profiles are used to control the preferred ringing mode, keys tones etc. The pre-defined profiles are:
General
Meeting
Outdoor
Silent
Car Kit
Keytones ON, Ringing ON, Vibrate OFF
Keytones OFF, Ringing OFF, Vibrate ON
Keytones ON, Ringing ON, Vibrate ON, Ringing FULL volume
Keytones OFF, Ringing OFF, Vibrate OFF
Keytones OFF, Ringing ON, Vibrate OFF, Auto answer and Backlighting Always on
The following profile settings can be customised using Edit
Voicecall ringtone
Videocall ringtone
Ring volume
Ring type (vibrate etc)
Message tone
Keytones
Warning Tone
Earpiece volume
The Car Kit profile is only engaged when the device is installed in a car kit and provides 2 extra
features, Auto Answer and Backlighting Always on.
41
7.2
Change the Shortcut Keys (Arrow keys)
The four arrow keys (▲▼◄►) can be customised to launch preferred features quickly from the idle
screen.
Menu > Settings > tab right to Handset > Shortcut Keys > OK
• Set each key in turn to the preferred setting
• Scroll to the chosen feature and press OK to assign the shortcut key.
Example Shortcut Setting:
File Manager
▲
Calendar ◄
► Messages
▼
Contacts
7.3
Change the Background Screen (Wallpaper)
Menu > Settings > Screen > Wallpaper
• Browse to the required folder eg Photos > My Pictures
• Choose the required picture and press Set to confirm
See Connectivity to import pictures
See Imaging to take photos on the camera
42
7.4
Change the default Ringtones
Menu > Settings > tab right to Profiles > Edit
• Edit the current profile to change the default Ringtones for all incoming calls
• Press OK to Modify the Voicecall ringtone (scroll down to select Videocall ringtone)
• Browse to Audios, Ring to see the available built in tones.
• See Connectivity to import your own music files.
7.5
Enable Vibrate Mode
Menu > Settings > tab right to Profiles > Edit
• Edit the current profile to enable the Vibrate function
• Scroll down▼ to Ringing Type and press OK to Modify
• Select the required mode and press OK to confirm.
• The vibrate icon
will be displayed on the Information Bar
7.6
Engage Meeting Mode with a single key press
• Mute the handset and switch it to vibrate mode by long pressing the # key from the Idle Screen:
• Press and hold the # key to engage and disengage Meeting Mode
• The vibrate icon
and mute symbol will be displayed on the Information Bar
7.7
Switch the Keytones off
Menu > Settings > tab right to Profiles > Edit
• Scroll down ▼ to Keytones and switch them off.
43
7.8
Change the Screen Brightness
Menu > Settings > Set Brightness
• Use the Up and Down ▲▼ keys to set the desired level.
7.9
Change the Display Backlighting
Menu > Settings > Display backlighting
• Screen full-light is the main screen lighting. After the set time the screen goes to half light
• Screen half-light, the screen is partially lit for the specified time
7.10
Set the Keypad backlighting
Menu > Settings > Keypad backlighting
Duration 30 secs
The keys remain illuminated for 30 seconds after the last key press
Always On
The keypad backlighting is enabled for the Duration specified
Customise
The keypad is only illuminated between the times set
Keypad backlighting is unnecessary during the day so a customised setting will improve
battery life
7.11
Add a Greeting and Owner name
Menu > Settings > Owner name
Menu > Settings > Greeting
• The Owner name is permanently displayed on the idle screen
• The Greeting is displayed during the start up sequence
44
7.12
What is the PIN Code?
Menu > Settings > Security > Activate Security Codes > Pin Code
• The PIN code is stored on the USIM card and protects your account against unwanted use
• Select On or Off and enter the PIN number to confirm. The original PIN number is provided by your
service provider but can be changed if required
• To change the PIN Code select Change Security Codes
• If you forget the PIN code it can be reset by your service provider.
7.13
What is the Handset Code?
Menu > Settings > Security > Activate Security Codes > Handset Code
• The Handset Code is stored on the handset and protects against unwanted use. If the handset is
lost or stolen it cannot be switched on without the handset lock code. This provides a greater level
of protection than the PIN code which protects the USIM card only. The default code is 0000
• Select On or Off and enter the Handset code, 0000.
• To change the Handset Code select Change Security Codes and enter a new code of your choice
• It is important to remember this code as it cannot be reset if it is forgotten.
7.14
•
•
•
•
Additional notes on PIN Codes
The PIN and PUK Codes are provided by your Service Provider
If you enter the PIN number incorrectly three times the phone will be PUK locked
Contact your service provider to get the PIN Unlocking Key (PUK code)
PIN2 Code is an additional PIN on the USIM card and is not generally used.
45
8
File Manager and External Memory
All user files and downloaded content are stored in the File Manager.
8.1
File Manager
Menu > Tools > File Manager
The file manager is separated into four folders, Photos, Audios, Videos and Others as shown:
Folder
Contents
Description
Photos
Top Animations, Latest Animations
Link to BigPond
Top Pics, Latest Pics
Link to BigPond
Wallpapers
Background screens for the handset
Audios
Videos
Others
My Pictures
Default directory for handset pictures
Latest Tones, Top Tones
Link to BigPond
Tone of the week
Link to BigPond
Ring
Pre-loaded handset Ring Tones
My Audios
Storage for your own Audio files (MP3 etc)
Top Videos, Music Videos
Link to BigPond
My Videos
Default directory for handset videos
Downloaded Internet files, Java apps etc.
46
8.2
Installing Additional Memory - microSD card
Handset memory can be increased by inserting a microSDHC card up to 4GB.
microSD cards up to 2GB are supported (FAT 16 format)
microSDHC (high capacity) cards up to 4GB are supported (FAT 32 format).
•
•
•
•
Open the microSD port cover on the right hand edge of the phone
Carefully insert the microSD card as shown above
Close the side cover
The external memory is accessed through the File Manager application described below.
With the microSD card inserted the default storage location for user photos and videos is the
External Memory. You can set this under Menu > Settings > Handset > Download Location
Always handle memory cards with care and avoid static discharge
47
8.3
Access the T-Flash card (microSD) using File Manager
Menu > Tools > File Manager > tab right to T-Flash Card
• All the folders and files that are stored on the card are displayed
8.4
File Manager and T-Flash Options Table
Depending on your location within File Manager, there are different Options (Left soft key) available as
shown in the table below:
Folder Options
File Options
Search
Mark
Mark Options
Mark all files
New folder
Send
Unmark all
Delete
Set as ringtone / wallpaper
Add to playlist / slide
Delete all
Add to playlist / slide
Move to
Rename
Move to
Copy to
Folder information
Copy to
Delete
Space information
Rename
Delete all
Delete
Play marked files
Delete all
Space information
Mark all files
New folder
File information
Space information
New folder
Press the Options to Mark files to perform the function to multiple file selections.
48
9
9.1
Alarms and Appointments
Set Alarms
Menu > Tools > Alarm > Add
Configure the alarm as required using the Alarm Setup Screen:
• Daily Alarm goes off every day
• Workday Alarm goes off Mon – Fri only (Rest days can be set under Options)
• Weekly Alarm will go off at the same time each week
• Once Alarm will only go off once
• Snooze can be set to be Off, 5, 10, 15 or 30 minute intervals
• Snooze will repeat for six times or until you Stop the alarm by pressing the OK key
• The Alarm Tone is preset by the Ringfile Press Edit to change if required
• If the Alarm time has passed it cannot be saved
• If the phone is switched off the Alarm will automatically switch on the handset.
Alarm Summary Table
Alarm type
Daily, Workday, Weekly, Once
Alarm date
Available with Weekly and Once
Alarm time
Set as required
Snooze
Off, 5, 10, 15, 30 minutes
Ringtone
On / Off
Ringfile
Alarm.mid, press Edit to change
Status
Enable / Disable
Alarm remark
Optional
49
9.2
Set Appointments using the Calendar
Menu > Tools > Calendar > Add
•
•
•
•
•
•
•
Add a Meeting, Memo or Reminder. The memo function does not include an alarm
Use the Meeting function to set repeat events such as Weekly Meetings and Anniversaries
Follow the prompts on screen to configure the event, see the examples in the table below
Events are shown by a highlighted box on the event day
Use Options to see the Week view and to change default behaviour under Settings
If the Alarm time has passed or is after the event time you cannot save the appointment
If the phone is switched off the Alarm will automatically switch on the handset.
Examples of different uses for the Calendar > Meeting function
Daily Reminder
Meeting with alarm
Repeat Meeting
Anniversary
Check mail
Appointment
Weekly Team
John’s Birthday
Dentist
Office
Start time
10.00am
11.00am
10.00am
08.00am
End time
10.00am
01.00pm
11.00am
08.00am
Start date
28/9/08
30/10/2008
29/9/2008
29/03/2009
Alarm set
On
On
On
On
Alarm time
09.45am
10.00am
09.45am
08.00am
Alarm date
28/9/08
30/10/2008
29/9/2008
29/3/09
Repeat set
Daily
Not repeated
Weekly
Yearly
Repeat until
28/10/08
N/A
29/9/2012
29/03/2030
Subject
Location
50
10 Imaging - Pictures and Videos
10.1
How to use the Camera
Menu > Multimedia > Camera
Shortcuts: Press and hold the side camera key to activate the camera.
The camera key activates the shutter and if pressed again will Save the image.
From Still mode press ►to change to Video mode as shown by the icon in the top right
hand corner.
• Use the Up and Down arrows to control the zoom*
• Press the Options button to:
¾ Change the Photo Size**
¾ Change the Photo Quality
¾ Change the Brightness
¾ Change the Contrast
¾ Apply an Effect (Normal, B&W or Sepia)
¾ Change the Shutter sound
¾ Save to – Handset memory or External Memory (SD card if fitted)
¾ Use the front / back camera
¾ Switch to Video Camera
* Zoom is not available on 1200 x 1600 as the screen is at maximum resolution.
** The default photo size is small to enable easy sending by MMS and Email.
To increase the size : Menu > Multimedia > Camera > Options > Photo Size
51
10.2
How to use the Video Camera
Menu > Multimedia > Video Camera
Shortcut: Press and hold the side camera key to activate the camera, press ►to switch
to video mode.
From Video mode press the ◄to change to Still mode as shown by the icon in the top right
hand corner.
• Use the Up and Down arrows to control the zoom
• Press the Options button to change the following:
¾ Video size, default is 15 seconds. Change this if required.
¾ Video Quality
¾ Brightness
¾ Contrast
¾ Effect (Normal, B&W or Sepia)
¾ Video sound
¾ Video format, MP4 or 3GP
¾ Save to – Handset memory or External memory (SD card if fitted)
¾ Use the front / back camera
¾ Switch to Camera
Press My Vids to view your saved video files
When viewing a video press Full Screen to view in Landscape.
52
10.3
Viewing pictures and videos
1. View the file directly from file manager
Menu > Tools > File Manager > Photos > My Pictures or
Menu > Tools > File Manager > Videos > My Videos
Scroll down the list to your chosen picture, Press Open to view the image.
2. Create a slide show to view pictures in sequence
Menu > Multimedia > Slide Show > Add > Photos > My Pictures
Select your required photos using Options > Mark and then Save the slide show
Press Start to automatically view the pictures sequentially.
3. View My Pics or My Vids from Camera mode
Menu > Multimedia > Camera > My Pics
Menu > Multimedia > Video Camera > My Vids
Press the Right Soft Key to select My Pics or My Vids to view your saved photos.
Additional features when viewing Pictures and Videos
Still Pictures
Videos
Full Screen
Right Soft Key
Full Screen, Landscape
Right Soft Key
Zoom in and out
Up and Down Arrows
Volume up and down
Up and Down Arrows
Rotate the image
1,3 keys
Brightness
2,8
Move the image
2,4,6,8
53
11 Music
To import music files onto the handset see the following sections:
• Import music files from your computer using JoinME (See Connectivity)
• Import music files from your computer or other device using Bluetooth (See Connectivity)
• Download music from BigPond Music: Menu > Games and Applications > Downloads
11.1
FM Radio
Menu > Multimedia > FM Radio
•
•
•
•
•
•
•
Insert the personal hands free kit (PHF). The headset acts as the antenna for the FM radio.
Tune the required station using the◄► keys or Options > Auto Search or Set Channel
Auto Search scans automatically for channels.
Use Set Channel to enter the frequency using the keypad and * key to access the decimal point
Remember to Save the new channel.
Press Options > Rename to personalize the channel name eg ABC
If an incoming call is received, the radio will be suspended while you answer the call.
11.2
Browse and play music files from File Manager
Menu > Tools > File manager > Audios > My Audios
• Press Open to play the desired music file.
Warning – At high volumes, prolonged listening to audio devices can damage hearing.
54
11.3
Create a new Playlist
Method 1: Create a Playlist from File Manager
Menu > Tool > File Manager > Audios > My Audios
• Scroll through the files and press Options > Mark (or Mark all files) to select files then Press OK
• Press Options > Add to Playlist > OK (for existing Playlist) or Add / New (to create a playlist)
• The selected song or songs will be added to an existing or new playlist
• Menu > Multimedia > Playlist > Scroll to select, OK to Play
Method 2: Create a playlist in Multimedia
Menu > Multimedia > Playlist > Add > Playlist name > OK > Audios > My Audios
• Scroll through the tracks and press Options > Mark to add the selected files to the playlist
• Press OK to save the Playlist, Press OK again to begin playing it
• Once a Playlist has been saved press Options > Edit to add or delete tracks and press Options to
rename, delete etc.
• Press Options to set the Repeat Setting; no repeat, all repeat or shuffle
• Use the side volume keys to adjust the volume
• Use ▲▼ keys to select tracks from your playlist
• Press the ◄► keys to skip tracks
• Press and hold the ◄► keys to forward or rewind through tracks
It is possible to create up to six different playlists.
55
12 Assisted-GPS
A-GPS is an advanced positioning system developed for mobile phone applications. The complex
calculations performed by a GPS receiver are carried out on an external server. Assistance information
is sent to the handset over the cellular system and is dependant on cellular coverage. The handset
contains an antenna and receiver specifically for A-GPS signals and this enables the handset to
calculate its position in terms of longitude, latitude and altitude.
• Stand alone GPS is a limited service pre-installed in the handset, that in good conditions will
provide a decimal location position.
• Full functionality requires additional applications to be installed or supplied by third parties. Please
contact your service provider for more information.
• The GPS receiver requires signals from at least three satellites and can take several minutes to
acquire.
• Reception is reduced in city areas, best reception is achieved with a clear view of the whole sky.
• The signal strength may be reduced in a vehicle, indoors or in overcast weather conditions.
• The antenna is in the top of the phone. Avoid blocking it with your hand to maximize reception
• It is not recommended to utilise stand alone GPS for mission critical applications.
• To switch GPS On or Off go to Tools, GPS Status. Perform a search under GPS Location. Results will
be dependant on the above conditions.
• Regular use of GPS positioning will increase battery consumption.
56
13 Connectivity
13.1
Use Join Me to connect the phone to a computer
Join Me is a program to connect the phone to a computer. After installation Join Me is used to manage
contacts, messages and calendar functions. It is also used to connect to the internet and transfer
music / picture files.
Compatibility
• The software is only compatible with Windows* XP Service Pack 2, Windows* 2000 SP 4 Windows
Vista*, MAC OS 10.5 and 10.4. However Join Me cannot be guaranteed to run on these systems.
• It is not compatible with Windows* ME, 98, 95 or with any 64 bit systems.
• The software may not run in all PC environments, or in conjunction with other software.
• Multi-boot systems are not supported.
• The software should be installed and run under the Administrator login.
Installation
• The following procedures and examples are only applicable to the PC Version of Join Me
• Please follow the installation steps carefully.
• If the installation fails please see the ReadMe file on the CD or consult our web site for more help.
www.zte.com.au.
*Windows, Vista, XP, 2000 and ME are registered trademarks of the Microsoft Corporation.
57
13.2
Installing Join Me
Please install the Join Me CD before connecting the phone to the computer.
• Insert the CD provided into the computer
• The CD will auto-start after a few seconds
• If auto run does not start then run Setup.exe from the CD
• The installation shield will launch and guide you through the installation
• Please follow the prompts to install the software
• When the installation is complete plug the handset into the computer using the USB lead supplied
• The USB lead is unique and should not be used for other devices (It is not the same as digital
camera leads)
• When the handset is plugged in the computer will automatically install the drivers. If this fails
consult our website for more help or access Windows Device Manager to update the drivers. See
www.zte.com.au for instructions
Note
If the phone is connected to the computer before installing the CD then the drivers will not be installed
correctly.
• Unplug the phone, un-install then re-install Join Me
• Press the Help Icon to access the built in Help menu.
• See www.zte.com.au for more assistance
58
13.3
Use Join Me to copy photos to your computer
Transfer photos from the handset to your computer using Join Me:
• Make sure the phone is switched on, connected to the computer and Join Me has been installed.
• The PC Connection on the handset needs to be set to USB
Menu > Settings > Handset > PC Connection > USB
• Connect the phone to the computer using the USB lead supplied
• Double-click the Join Me icon on the desktop.
• Select the phone type and press Connect.
• Select the Media tab
as shown on the next page
• Double click on My Phone in the bottom left hand corner
• Double click on Photos to expand the folder structure
• Double click on My Pictures to see the picture files on the right hand side.
• Drag* the required file from the file list and Drop* it into the required destination folder on the PC.
• The file will be copied to the destination folder (Desktop in the example below).
• Files can only be transferred into Folders.
The default picture size is very small when viewed on the computer.
See section 10.1 to change the image size.
*
Drag and Drop is a method of copying files. Click on the file, hold down the left mouse button,
move the mouse pointer to the required destination and release the left mouse button to Drop
the file to that location. Alternatively right click on the file and use Copy and Paste from the
menu.
59
Copy files (eg Photos) from the phone to the computer using JoinME
1. Select the Media Tab
2. Select My Pictures folder on My Phone
3. Drag the picture from My Pictures
to a folder on the PC
4. Alternatively right click on the file and
use Copy and Paste from the menu
Files can only be copied into Folders
60
13.4
Use Join Me to transfer music from a computer
Music files can be transferred onto the phone using Join Me.
• Make sure the phone is switched on, connected to the computer and Join Me has been installed.
• The PC Connection on the handset needs to be set to USB
Menu > Settings > Handset > PC Connection > USB
• Double click the Join Me icon on the desktop.
• Select the phone type and press Connect.
• Select the Media tab as shown in the picture on the next page.
• Double click My Phone in the bottom left hand corner.
• Double click Audios to open up the Audios folder.
• Locate the music files on the computer by browsing through the Windows file structure in Join Me.
• Drag the required file from the top half (computer) and drop it into My Audios on the phone.
• The file is copied to the destination folder (as shown below). Files can only be copied into Folders.
• Alternatively Right Click on the file, choose Copy, then go to the destination folder and Paste.
MP3, WAV, WMA and MIDI Files are supported but MP3 is preferable due to smaller file size.
61
Copy files (eg Music) from the Computer to the handset using JoinME
Use drag and drop to copy the
selected file from the computer to
the My Audios folder on the handset.
Alternatively select the file, right click
to Copy the file, select the destination
folder (on the handset) and choose Paste.
Files can only be transferred into user folders
on the handset. Eg. Transfer music files into
My Audios, pictures into My Pictures and Java
games and applications into the Others folder.
All other folders are write protected.
62
13.5
Enter Contacts using Join Me
Use Join Me to enter new contacts into the phone.
.
On the phonebook tab enter
contacts directly using the PC.
Select
“New
Contact”
then
complete the required fields.
Select the Save Position; Local,
Phone ,(U)SIM or All.
The save position ‘Local’ refers to the computer. Remember to change this if you want to save
contacts directly to the handset or use the copy function to copy contacts from Local to Phone.
There is less storage available on the USIM card so some of the fields are greyed out.
63
13.6
Copy Contacts from the phone to the computer
2. ‘Select all’ by checking the
box at the top of the list.
3. Drag and drop the complete
list to Local.
This will copy all the USIM
contacts to the PC (Local)
You can also select an
individual contact to copy it in
either direction.
1. Select the USIM card to
copy contacts from the
USIM to the PC.
You can also right click on the
Contacts grid and Import from
Outlook. See 13.7 below…
Copy one or all of the contacts from Local to Phone using the same method
64
13.7
Import Contacts from Microsoft Outlook
• Launch Microsoft Outlook, load Join Me and connect your handset to the computer.
• Note, at the end of the import process Outlook can shut down. Please save any information
beforehand.
• Select the PhoneBook tab in Join Me, see image in 13.6 above.
• Click on the
button and select Import contacts from Outlook.
• Select one of the 3 listed options, Replace with new items, Allow Duplicates or Do not create
duplicates and click OK.
• Only contacts in the root folder (Contacts) of Outlook will be copied
• The following fields are imported from Outlook to Join Me as below:
Outlook
Join Me
Full Name
Name
Mobile Telephone Number
Home mobile
Home Telephone Number
Home phone
Business Telephone Number
Work mobile
Company Main Telephone Number
Work phone
Other Telephone Number
Other mobile
Company Name
Company
Profession
Notes
Web Page
Web
65
13.8
Import Calendar events from Microsoft Outlook
• Launch Microsoft Outlook, load Join Me and connected your handset to the computer.
• Note, at the end of the import process Outlook can shut down. Please save any information
beforehand.
• Make sure you are on the Calendar tab in Join Me
• Click on the
button and select Import Calendar from Outlook.
• All calendar entries are copied into Join Me
• Select the required entries, or select All
• Copy the imported entries from Local to Phone
13.9
Use Join Me to connect to the Internet
You can use the mobile phone as a dial up modem to connect a computer o the internet.
• Make sure the phone is switched on and connected to the computer and Join Me has been
installed.
• The PC Connection on the handset needs to be set to USB
Menu > Settings > Handset > PC Connection > USB
• Double click the Join Me icon on the desktop.
• Select the Internet tab as shown below
• Press Connect to go online
The default APN is Telstra.internet. Please check with your service provider to confirm the
correct APN if required.
66
13.10 Connect to a Bluetooth Device
Bluetooth is used as a wireless connection for headsets, hands free car kits and computers. Not all
applications or devices are supported. Bluetooth is an open forum and manufacturers choose which
functions to implement.
The handset supports Bluetooth 1.2 with Handsfree, Headset, FTP and DUN profiles.
Consult the other device for compatibility, connection issues and to find the pairing password.
Please follow the process carefully. Connecting to a Bluetooth device first time around requires
authentication where both devices share a password.
When the devices are paired and connected the process is more automatic.
Connect to a Bluetooth Device
Menu > Tools > Bluetooth > Bluetooth Manager
• Press the Left or Right Arrow Key to switch Bluetooth on.
• Go down to Visible then press the Left or Right Arrow Key to select Show. The phone name can be
customised if required. Press OK to confirm.
• Go to My Devices and press OK. Press Search to look for Bluetooth devices nearby.
• The chosen device must be switched on and in pairing mode.
• Available devices are listed in the device list. Select the required device and press OK to Connect.
• Enter the pass code, usually 0000 or 1234. Consult the device for more information.
• If you are connecting to a PC or another mobile enter the same password when requested on that
device.
• Once the password has been shared and accepted by both devices they are paired.
67
Send files from the handset to another device
Menu > Tools > File Manager
• Browse through the folders to the chosen file
• Press the Left Soft Key for Options
• Choose Send then select Bluetooth and press the OK Key
• If no devices are shown press Search
• Select the required device to send the file to
• Enter a pass code and use the same pass code on the other device (eg 0000).
Receive files from another device
• When another device sends you a file press Yes to authorise the connection
• Press Yes to accept the file
Connect to a Bluetooth Car Kit or Personal Headset
Follow the manufacturer’s instructions carefully to enable Pairing Mode on the other device.
It is not possible to connect the phone to the other device unless Pairing Mode is enabled.
Select the required device, share a pass code and press Connect.
Menu > Tools > Bluetooth > Bluetooth Manager > Turn On, Show > OK
• Make sure Bluetooth is On and in Show mode and the other device is in Pairing Mode
• On the handset go to Bluetooth: Menu > Tools > Bluetooth > My Devices
• Press the Right Soft Key to Search
• From the list of available devices select the required device and press OK to Connect
• Enter the pass code specified in the user guide of the far end device (eg 0000 or 1234)
• When the devices are paired the handset will report the device has been added
68
• In My Devices go to the new device and press OK to Connect
• The devices are now Connected
• When connected, incoming calls are sent to the Bluetooth device automatically. Press the call
button to answer.
• During a call press Options > Switch to Handset to return the call to the handset
13.11 Dial Up Networking using USB or Bluetooth
Dial Up Networking (DUN) is a method to connect your PC or MAC to the internet using the handset as
a modem.
1.Dial up Networking over USB using the Windows Wizard
Make sure Join Me is installed, the handset is on and connected to the PC using the USB lead supplied.
Example for Windows XP
On the PC go Start > Accessories > Communications > New Connection Wizard and follow the prompts:
Connect to the internet > Set up my connection manually > Connect using a dial up modem
Select the ZTE USB Modem and uncheck any other modems
The ISP Name can be any name you like eg. T165i Handset
Set the Phone number to *99# > The Username and Password must be blank >
‘Make this the default Internet connection’ can be unchecked (optional) >
‘Add a shortcut to this connection to my Desktop’ can be checked (optional) > Finish
Press Dial to test the connection
The PC will open an internet connection using the handset as a high speed modem
69
2. Dial Up Networking over Bluetooth
Bluetooth can be considered as a wireless replacement for the USB connection and is compatible with
any DUN enabled Bluetooth device. Use Bluetooth to connect the handset to a PC or MAC and use Dial
Up Networking to create an internet connection.
a) Both devices must have Bluetooth ON
Handset: Menu > Tools > Bluetooth > Bluetooth Manager > Turn On, Show > OK
PC or MAC: Enable Bluetooth using the appropriate hardware or software settings
b) Set the handset PC Connection to Bluetooth
Menu > Settings > Handset > PC Connection > Bluetooth
c) Create a New Connection on the PC or MAC
Launch the Bluetooth manager software on your PC or MAC. This varies depending on your platform,
hardware and software. Create a new connection and enter the same password, when prompted, on
each device. Select the T165i Handset, the Dial Number is *99# and the Username and Passwords are
blank.
When the Bluetooth manager opens a connection to the handset, accept the incoming connection by
pressing Yes when prompted.
The PC or MAC can now connect to the internet via the handset.
The features described are dependant on external suppliers’ hardware and software and vary between
platforms and components. Consult your system supplier for more information.
70
13.12 PC Connection
Menu > Settings > Handset > PC Connection > Bluetooth
PC Connection specifies how the handset initiates data connections to the PC. It can be set to be via
Bluetooth or via the USB cable. Join Me requires the USB connector, other transfers can operate via
Bluetooth if supported by your system.
If PC Connection > Bluetooth is selected then Join Me will not connect to the handset.
Restore the PC Connection to USB to re-enable Join Me.
13.13 Synchronize with a network server (SyncML)
Use SyncML to enhance your Personal Information Management by synchronizing Contacts and
Calendar information on the handset with those on a network server.
Menu > Tools > SyncML
• Complete the Sync settings before synchronizing the contacts and calendar
• Select to use Two-way fast sync or Two-way slow sync
• Use Query log to view the SyncML info
• SyncML requires network support and may require an additional subscription
• Contact your Service Provider for more details.
71
14 Other Facilities
14.1
Browser
Menu > Tools > Browser
Home
the home page is set by your Service Provider
New Link
enter a web address manually using the keypad
Bookmark
Link to a previously saved page
History
Display pages visited
Saved Page
View a local copy of a previously saved page
Settings
Display browser settings (see below)
Version
Display current browser version
Menu > Tools > Browser> Settings > Advanced Settings
Connection settings
Sets the APN, preset by your service provider
Advanced settings
Customise the browser display modes, sound, cache, cookies etc
Clear cache
Clears all cache data
Clear Cookies
Deletes all cookie information
Clear autofill list
Deletes all input history items
Certificate
List the root and CA certificates on the handset
72
14.2
Stopwatch
Menu > Tools > Stopwatch
• Press OK Key to Start timing.
• Press OK to Stop timing. The screen will display the event time.
• Press OK to continue timing.
• Press Right Soft Key to reset.
14.3
Calculator
Menu > Tools > Calculator
•
•
•
•
Press 0~9 keys to enter numbers, Decimal to enter the decimal point.
Press ▲▼▲▼ for +, –, ×, ÷
Press the End key to clear last digit and results.
Press OK to show the result
14.4
World Time
Menu > Tools > World Time
•
•
•
•
The world time function provides time information on major cities worldwide.
Scroll to the desired city by using the Left / Right keys.
Select the required city then press the OK Key to save the selected city as the local time zone.
Note changing time zones changes the current time setting.
73
14.5
Currency Conversion
Menu > Tools > Currency Conversion
•
•
•
•
•
Convert currencies quickly and easily
The exchange rate stays set after you close the function
Use the ▲▼arrows to highlight the required field
Press Decimal to use a decimal point
The result is displayed in local or foreign currency automatically
14.6
PocketNews
Menu > Tools > Pocket News
Select the required feature from the available menus. The information is regularly updated by your
service provider and is be sent to your handset by SMS.
14.7
Games and Applications
Menu > Games and Applications
• Download the latest games from your service provider or other specialist websites
• Note that DRM Protected files (Games, Music and Images) cannot be copied to other devices
• The handset supports Java Midlet 2.0
• Use Join Me to copy other games from your computer (see Connectivity)
• Games and applications are saved into the Others folder
• Select Open to install the game.
74
14.8
Voice Recorder
Menu > Multimedia > Voice Recorder
• Press OK to Start recording the voice memo
• Press OK to Pause / Continue (Contin.) recording
• Press the Right Soft Key to Stop recording
• Press OK to Save. The file will be saved to My Audios
• Press Right Soft Key to Discard the voice memo
• Press Left Soft Key to Send the memo via MMS, Email or Bluetooth.
14.9
Slide Show
Menu > Multimedia > Slide Show
• Add pictures by pressing Add or Options > New Slide
• Browse to My Pictures and Mark the pictures you want. Press OK to finish, Play to play.
• Use Options to Edit, create New slide, Rename, Delete, Delete all, and View the image info.
14.10 Streaming URL
Menu > Multimedia > Streaming URL
Streaming URL are links to audio or video streaming content over the internet. The content is only
available while connected to the server and depends on your network provider.
14.11 Connections
Menu > Settings > Handset > Connections
Connections are pre-defined by your service provider and enable the handset to connect to the
internet via WAP and to send multi media messages (MMS). When using an alternate carrier, Add a
new Connection setting as defined by your service provider.
75
14.12 Access Point Settings
Menu > Settings > Handset > Access point settings
Access Point Settings (also called APN) are pre-defined by your service provider and enable the
handset to connect to the internet via WAP and to send multi media messages (MMS). When using an
alternate carrier, Add a new Connection setting as defined by your service provider.
14.13 Restore default settings
Menu > Settings > tab right to Handset Settings > Restore Default Settings > 0000
If the handset is not working as normal, restore the handset to default factory settings. The default
Handset Lock Code is 0000. User content will not be erased.
14.14 Auto Keylock
Menu > Settings > Handset > Keylock
Auto keylock can be set to automatically lock the keypad after a predetermined time. Set your desired
time from the available choices. Press * followed by the Right Soft Key to lock or unlock the keypad.
Emergency numbers can still be dialled while the keypad is in the locked state.
Enter the emergency number on the keypad then press the green Call Key.
76
14.15 Download Location
Menu > Settings > Handset > Download Location
When a microSD card is installed the default save location for user photos and videos changes to the
External Memory. This refers to the microSD card.
14.16 Network Settings
Menu > Settings > tab right to Handset Settings > Network Settings
Preferred mode: Lock the handset to GSM or UMTS (3G) Networks
Preferred Band: Lock the handset to certain bands, U = UMTS, G = GSM
Preferred selection: Choose which network to register with from a list of available networks.
Manual Network Selection overrides the Preferred Mode and Band settings.
The handset will stay on the chosen network and related band. Eg. If you choose a GSM
Network, the Preferred Mode will switch to GSM and remain in GSM-only mode. Further
searches performed by Preferred Selection > Manual mode will only detect networks from the
GSM band. To return to normal mode set Preferred Mode and Preferred band to Automatic.
77
14.17 CTM
Menu > Settings > tab right to Handset > CTM
CTM (Cellular Text Telephone Modem) is a text based communications protocol to offer support to
hearing and speech impaired people. Hearing or speech impaired persons can communicate using a
teletype (TTY) terminal connected to the mobile phone via a CTM Modem. The TTY signals are sent
alongside speech so it is possible to configure the system to enable speaking and hearing as well as
typing or receiving text to the TTY device. See below for the options available:
CTM Mode
Description
Full
Text entered on the terminal is sent to the other party. Received text from the
Talk & Read
Received text is displayed on the terminal, Voice is relayed to the other party.
Write & Hear
Text entered on the terminal is sent to the other party with incoming speech
other party is displayed on the terminal.
heard from the other party.
Off
All CTM is disabled, use the phone as normal.
• If you are using a TTY terminal the terminal baud rate must be set to 45.45 bps
• If you are using a termina with a built in CTM modem then select CTM Off on the handset
78
15 Technical, Support and Warranty Information
15.1
Troubleshooting and FAQ’s
Please check the manual thoroughly before contacting your service provider
Symptom
Solution
No incoming ring
or alarm tone
Check the ring tone and ring volume settings under Profiles
Check the handset is not muted (Long press the # Key)
(No) keytones when
pressing keys
Check the key tone settings in the current profile.
See 7.1 Change the Profiles
A phone number cannot
be dialled
Check for network coverage
Check whether any call restrictions are set. See Call Barring
Short messages cannot be
sent or received
See Text Message Settings and check the SMS centre number is
correct. Contact your service provider for more details.
MMS messages cannot be
sent or received
Your subscription does not include data services. Check with your
service provider.
How do I switch off
Predictive Text?
The # key is used to toggle between different modes.
See Chapter 6 for details.
I cannot connect to
FOXTEL or BigPond
Your subscription is not provisioned for data services. Check with
your service provider.
I cannot connect to
Join Me
Check: Menu > Settings > Handset > PC Connection > USB
Uninstall and re-install the CD software
See FAQ’s at www.zte.com.au for more assistance
79
Symptom
Resolution
My phone is slow to
respond, handset storage
problems
Restart your phone every day to refresh the memory
Delete or archive old SMS messages and other content
Restore default settings:
Menu > Settings > Handset > Restore Default > 0000 > Yes
The battery discharges
quickly
Possible network coverage issue. Check the signal strength. With
only 1 or 2 bars, the battery has to work harder to maintain
network contact. Limit multi-media and Bluetooth usage to save
power. The battery may be worn out and needs to be replaced.
I cannot charge the phone
Confirm the charger is properly inserted. Remove the battery, clean
the contacts using a dry cloth, and check it is inserted correctly. The
battery may be worn out and needs to be replaced.
Tip: Charge the phone using the supplied USB cable.
How do I enter text in an
SMS?
From the phone number field press the down arrow twice to move
into the text area. Use predictive text or abc mode to manually
type words. See chapter 6 for details.
How do I change the
Ringtone?
Edit the current profile and select a new tune from the Audios
directory. See chapter 7 for details.
The handset switches off
after charging.
The handset is charging in the off state. Press and hold the Red key
to switch the handset ON or charge it in the ON state
The handset switches on
automatically
An alarm or calendar event will switch the handset on
automatically.
80
Symptom
Resolution
My phone is not able to
connect to other Bluetooth
devices
Turn Bluetooth on. Set visibility to Show. Possible compatibility
issues. Manufacturers incorporate different Bluetooth profiles. Not
all functionality is supported.
How do I transfer pictures
via Bluetooth to a photo
printer (eg Kodak)?
This is not supported due to different Bluetooth profiles. Copy
photos using Join Me or a T-Flash card
15.2
Error Messages
Message
Solution
No (U)SIM detected
Check a valid USIM card is inserted
See 2.1 How do I insert the USIM Card?
Enter PIN code
Enter the correct PIN code supplied by your service provider
Enter PUK code
Contact your service provider to get the PUK code
Enter 16 digit unlock code
Please contact your service provider
Enter handset lock code
The default handset lock code is 0000
81
15.3
Technical Parameters
Network
3G WCDMA 850, 1900, 2100 MHz with HSDPA data up to 7.2 Mbps
Compatibility
2G GSM 850, 900, 1800, 1900MHz with EDGE data up to 236.8Kpbs
Dimensions L×W×H
Approx 117mm x 51mm x 16mm
Weight
Approx 119g (Including standard battery)
Features
MP4 video, MP3 audio, 2.0/0.3MPixel camera, Video Phone, USB, FM
Radio, A-GPS, Java MIDP 2.0, 2.0” 262K colour LCD display, 240 x 320
pixels, MMS, E-mail, Calendar, Speakerphone, Voice Recorder, Bluetooth
1.2 Stereo, Supports 4GB microSDHC, CTM.
Battery
1300mA hours, Lithium ion (Li-ion)
Continuous idle
Up to 250 hours
time*
Continuous talk
180 minutes on GSM network, 180 minutes on WCDMA network,
time*
Video call >70 minutes
Charge time
Approximately 3 hours
Battery Life
Approximately 400 charge cycles
Supported Files
JPG, BMP, GIF, MP3, WAV, MID, WMA, MMF, AMR, MP4, 3GP, TXT
*The phone’s talk and idle time are based on ideal working environments. The use of extended
backlighting, browser, and network conditions can reduce battery life and talk/idle time.
82
15.4
Support Information
• For Warranty Service directions please consult the ZTE website at http://www.zte.com.au
• All calls for PIN number enquiries, Network problems, Next G Services, BigPond account information,
Web Access, Account and Billing Information, USIM card registration and general enquiries should
be directed to your Service Provider.
15.5
Warranty Information
The warranty does not apply to defects or errors in the product caused by:
(a) Reasonable abrasion.
(b) Misuse including mishandling, physical damage, improper installation, unauthorized
disassembly of the product.
(c)
Water, exposure to solvents or any other liquid damage.
(d) Any unauthorized repair or modification.
(e) Power surges, lightning damage, fire, flood or other events outside ZTE’s reasonable control.
(f)
Use of the product with any unauthorized third party products such as generic chargers.
(g) Any other cause beyond the range of normal usage for products.
The End User shall have no right to reject, return, or receive a refund for any product from ZTE under
the above-mentioned situations.
Note: Consult the warranty card for full information
83
16 Environmental Statement
The ZTE handset is made using the latest manufacturing techniques and environmental standards to
reduce waste and hazards to the environment. However at the end of life of the equipment the
manufacturer recommends that you return the handset and accessories to the nearest re-cycling
depot or send it to our recycling agent below. Valuable materials such as gold, silver, and copper can
be recovered from the handset. Any toxic materials will be prevented from entering the environment
and the waste materials will be recycled.
At the end of life of the equipment please send the handset, batteries and charger to:
MRI (Australia) Pty Ltd
or
20-24 Dennis St
MRI Sydney
1 – 4 Bentley Street
Campbellfield
Wetherill Park
VIC 3061
NSW 2164
www.mri.com.au
MRI Australia recycles every part of the equipment and diverts over 90% of the materials from landfill
for re-use.
84
17 General Safety and Maintenance Information
The handset contains delicate electronic circuitry, magnets and battery systems. You should treat it
with care and pay attention to the following points:
may be affected by the handset.
• Handle the handset with care. Do not drop or
• Take care not to allow metal objects such as
throw the handset down roughly.
coins or keys to come into contact with the
• Do not immerse in any liquid. The handset
battery terminals.
contains a liquid detection sticker and the
• Do not dispose of batteries in a fire.
warranty will be voided by any liquid
• Do not throw used batteries into household
damage.
rubbish, return them to a recycling point.
• Do not place the handset near computer
• Do not connect the handset to any other
disks, credit cards, and other magnetic media.
chargers or cigarette lighter chargers.
The information contained on disks or cards
• Only use the supplied charger.
may be erased or damaged.
• Be careful not to pierce the battery with
• Do not leave the handset or battery in direct
sharp objects and do not use damaged
sunlight or near other heat sources where
batteries.
temperatures could exceed 45°C.
• Do not disassemble or modify the battery.
• Keep the handset, battery, charger and other
• Stop using the battery if abnormal heat,
accessories away from children.
odour, discolouration, deformation, or
• In the unlikely event of a battery leak avoid
abnormal condition is detected during use,
contact with your eyes or skin. Flush with
charge, or storage.
water and consult a doctor.
• Do not put the battery in your mouth.
• Observe and obey warning signs at petrol
• Only use original replacement batteries.
stations, airports and hospitals.
• Do not attempt to dismantle the handset or
• The operation of some medical electronic
any of its accessories.
devices, such as hearing aids and pacemakers,
85
• Do not place the handset close to the edge of
a table in case it moves when set on vibrate
mode.
• Do not put the handset into a microwave
oven, dryer, or high-pressure container.
• Don’t use the handset immediately after a
sudden temperature change eg. from an air
conditioned
environment
to
high
temperature and humidity outside. In such
cases there could be condensing moisture
inside the handset which can cause internal
damage. Switch off and leave for 30 minutes
before use.
• Do not use the handset while driving or
operating other machinery.
• Do not use the handset where blasting is in
progress.
• Switch the phone off when boarding aircraft.
• Do not leave the handset at the bottom of a
bag where it may be damaged by sharp
objects.
• Do not use your phone or accessories at
refuelling points, near fuel or chemicals or
store it in the same compartment as
flammable gas, liquid or explosives.
• At high volume, prolonged listening to audio
devices can cause hearing loss.
• Do not leave the handset discharged or
disconnected for a long time, otherwise your
personal data may be lost.
• Remember to make backup copies of all
important data on the handset.
• Take care when the phone is in your pocket.
Sitting down may damage the handset.
• It is normal for the handset to become warm
while the battery is being charged.
• Under poor network conditions battery life is
considerably reduced.
• When the battery is thrown away cover the
terminals with insulating tape.
• Please recycle the packaging and all parts.
• Emergency service coverage is dependant on
network availability and battery status.
• It is always good practice to switch off the
handset regularly.
• Do not expose the handset to oils or solvents.
• If you have an alarm set the handset will
switch on at the prescribed time.
86
Index
Advanced Call Settings
Answer a Call
32
Dictionary
21, 29
Download Location
36
47, 77
Appointments
49
DTMF
Background Screen
42
E-Mail
39
Backlight Duration
44
Emergency Calls
31
35
28
Battery
18, 20
En
Bluetooth
67, 68
Environmental
84
68
FAQ’s
79
Calculator
73
File Manager
46
Calendar
50
FM radio
54
Call Divert
32
Handsfree
28
Call History
27
International Dialling
28
Call options
28, 30
Bluetooth Car Kit
Camera
Java Games
74
51
Join Me
CD
58
Key Tones
43
Change PIN Numbers
45
Last Number Redial
27
Charger
19
Main Menu
22
Charging
20
Make a Call
21
Contacts
23, 25
Make a Voice Call
27
57, 58
Copy photos
60
Make Videos
52
CTM Set
78
Meeting Mode
43
Dial Up Networking (DUN)
69
Microsoft Outlook
65
87
MP3 Player
54
Shortcut
42
Multimedia Message
38
Silent Mode
43
Music Player
54
SIM card
17
My Words
37
Slide Show
75
77
SMS Message Length
37
Snooze
49
Network Settings
PC
58, 61
PIN Codes
45
Speakerphone
28
Playlist
55
Speed Dial
25
Predictive Text
36
Stopwatch
73
Preferred mode
77
Streaming URL
71
Preferred selection
77
SyncML
71
Profiles
41
Take Pictures
51
Push Messages
39
Technical Parameters
82
Receive a Text Message
35
Troubleshooting
79
Restore default settings
76
USB
19
3
Using T-Flash cards
47
3
Vibrate Mode
43
RF Energy
RF Safety Information
Ringtone
43
Video Call
29
Safety Information
85
Voice Recorder
75
44
Wallpaper
42
Screen Brightness
Send a Text Message
21, 35
WAP
39
Set Alarms
49
Warranty
83
Set the Time
20
World Time
73
88
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement