HLA Fusion v3.5 Install Guide_EN

HLA Fusion v3.5 Install Guide_EN
Installation Guide
HLA Fusion™ Software
Version 3.5 Service Pack
Catalog #: FUSPGR
CE-IVD: For In Vitro Diagnostic Use.
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
All of One Lambda software products are designed to assist personnel experienced in HLA analysis by suggesting
typing results. However, any clinical or diagnostic results must be carefully reviewed by a person qualified in HLA
typing to assure correctness. This software may be used to aid in suggesting results, but should not be used as the
sole method for determining reportable results. This software is meant as a laboratory aid, not as a source of
definitive results. The software design does not mitigate hazards associated with the software. The laboratory
director or technologist trained in histocompatibility testing is required to review all data to detect any problems with
the software. Please note that this document was prepared in advance of the HLA Fusion software release.
Therefore, you may notice slight differences in the content of the actual application screens.
21001 Kittridge Street,
Canoga Park, CA 91303-2801
Tel: 818.702.0042 • Fax: 818.702.6904
www.onelambda.com
HLAF-INSTALL-v3.5.0-EN-01 Rev 0 (HLA Fusion Version 3.5 Service Pack Installation Guide)
ii
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
© 2015 Thermo Fisher Scientific Inc. All rights reserved. Windows and WinZip are trademarks of Microsoft Corporation. All other trademarks are the property of
Thermo Fisher Scientific and its subsidiaries. Specifications, terms and pricing are subject to change. Not all products are available in all countries. Please consult
your local sales representative for details.
HLAF-INSTALL-v3.5.0-EN-01 Rev 0 (HLA Fusion Version 3.5 Service Pack Installation Guide)
iii
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
Table of Contents
Installing the HLA Fusion™ Software v3.5 Service Pack .................................................................................... 1
Installation Notes.................................................................................................................................................. 1
Installing HLA-SP 3.5 ........................................................................................................................................... 2
Installation Steps for the DATABASE portion of HLA-SP 3.5 .............................................................................. 4
Verify the correct installation of the service pack update..................................................................................... 7
Desktop Icons ...................................................................................................................................................... 8
Version History ..................................................................................................................................................... 8
HLAF-INSTALL-v3.5.0-EN-01 Rev 0 (HLA Fusion Version 3.5 Service Pack Installation Guide)
iv
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
Installing the HLA Fusion™ Software v3.5 Service Pack
The HLA Fusion™ Software v3.5 Service Pack (HLA-SP 3.5) is available for users who have already installed
the HLA Fusion 3.0, 3.2, 3.2 Hot Fix 1, 3.3, or 3.4 version of the software. This service pack includes all the
changes made since version 3.0 was released.
Installation Notes
1. Back up your HLA Fusion 3.0, 3.2, 3.2 Hot Fix 1, 3.3 or 3.4 database using the Database Utility. Refer to
the HLA Fusion Database Utility User Manual for instructions on using the database backup function.
2. Make sure that all users log off and close HLA Fusion software before installing HLA-SP 3.5.
3. Install HLA-SP 3.5 on each individual workstation running HLA Fusion software that you want updated. You
must have administrator privileges on the computer in order to install HLA-SP 3.5.
NOTE: After HLA-SP 3.5 has been successfully installed, the InstallShield Wizard screen will indicate that
you have successfully installed version 3.0 of HLA Fusion.
4. IMPORTANT: You must update your Fusion database to version 3.5 after HLA-SP 3.5 has been installed
or Fusion will refuse to operate. Use the function Upgrade prior versions of HLA Fusion database to 3.5
in the Database Utility, as described below.
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
1
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
Installing HLA-SP 3.5
NOTE: The screen shots captured below represent the most common installation scenario. Some screens may not
appear, and others that are not captured in this Install Guide may display. If you have any questions, please see
your administrator.
1. Download the HLA-SP 3.5 Service Pack file HLA Fusion 3.5.zip (or .rar) here:
http://download.onelambda.com/pub/tray_info/Windows/HLA_Fusion_Catalogs/Document/HLA_Fusion IVD 3_5/
2. Open the .zip (or .rar) file to find the installer, “HLA Fusion 3.5.exe” (shown below):
3. Locate the file HLA Fusion 3.5.exe on your computer using Windows Explorer.
4. Double click the HLA Fusion 3.5.exe file to begin the update process. This may take a few moments.
During this time you will see a screen similar to this one:
The service pack setup process will now locate the HLA Fusion 3.0 installation directory on your computer.
The following screen appears:
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
2
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
5. Press Update to continue. Depending on whether your computer runs Windows XP or Windows 7, you will
see one of the following screens (or similar):
Click Allow or Yes (as shown above) to continue with the update.
6. You will then see a screen similar to this one:
If the setup process is successful, the following screen appears:
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
3
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
7. Click Finish to complete the setup.
Note: Steps 1 – 5 must be repeated on all computers running HLA Fusion 3.0, 3.2, 3.2 Hot Fix 1, 3.3, or
3.4 software that you wish to update with HLA-SP 3.5.
Installation Steps for the DATABASE portion of HLA-SP 3.5
1. Launch the Database Utility 3.0 from one of the workstations. You must have an administrator user ID and
password to login.
The following screen appears:
a. If the computer where the service pack update is being installed already has a local instance of the
Fusion database, (local)\Fusion, but it fails to populate when you launch the HLA Fusion Database
Utility, you need to check the computer’s SQL Server Browser properties.
i. On the Start menu, right-click My Computer, and then click Manage.
ii. In Computer Management, expand Services and Applications, then click Services.
iii. In the list of services, double-click SQL Server Browser.
iv. If the Service Status in the SQL Server Browser Properties window is stopped, click Start
and enter (local)/Fusion in the SQL Server field on the Fusion Database login screen.
Note: You may need to make sure the Startup type is set to Automatic to start the
service, or the Start button may be greyed out.
2. Click OK to continue.
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
4
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
The following screen now appears:
3. Select Upgrade prior versions of HLA Fusion Database to 3.5 under Data Migration.
4. Select a Database to upgrade from the dropdown menu, and click Upgrade:
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
5
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
While the database is upgrading, the following screen appears:
Once the database has been successfully upgraded, the following screen appears:
5. Click Yes to continue. The following screen appears:
6. Click OK to complete the upgrade process. You will be returned to the Database Utility screen.
7. Click Exit to exit the Database Utility.
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
6
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
Verify the correct installation of the service pack update
1. Launch HLA Fusion software from one of the workstations where you have installed HLA-SP 3.5.
2. Verify that the version number on the Security Login screen is 3.5.6.13925:
3. Verify that the version number on the Home Screen is 3.5.6.13925:
4. Click HELP on the HLA Fusion Home Screen toolbar.
5. Select About HLA Fusion™ from the drop-down menu.
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
7
One Lambda, Inc. | A Thermo Fisher Scientific Brand
HLA Fusion Version 3.5 Service Pack Installation Guide
6. Verify that the Build No. on the “About HLA Fusion” screen is 3.5.6.13925:
If the file version is not 3.5.6.13925 after the service pack update, please contact One Lambda technical
support for assistance.



Call: 800-822-8824 from the United States, outside of the greater Los Angeles area.
Call: 818-702-0042 from the greater Los Angeles area.
E-mail: [email protected]
Desktop Icons
Installing HLA Fusion automatically places two shortcut icons on your desktop, a program and a database icon,
both with the HLA Fusion 3.0 label. We recommend that you do not re-name these icons. If you re-name these
icons, please be aware that if you later re-install HLA Fusion, the program won’t recognize the icons under the new
names and will install another set with the 3.0 label.
Version History
Revision
Date
0
11/03/2015
Revision Description
Original release
™ HLA
Fusion is a trademark of One Lambda, Inc., now part of Thermo Fisher Scientific.
is a registered trademark of Microsoft Corporation.
© Copyright by One Lambda, Inc., now part of Thermo Fisher Scientific. All rights reserved. October, 2015
® Windows
HLAF-INSTALL-v3.5.0-EN-01 Rev. 0
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement