Available online and in the app store:
Instruction
Manual
For use with Breezeboard PRO models:
How to build your buggy...
Please check the contents of your box before beginning to build your Breezeboard PRO Buggy...
1 Seat (1)
2 Arms (2)
3 Arm Holders (2)
4 Velcro Straps (2)
5 Seat Platform (1)
6 Chassis Extender (1)
7 Rubber Protector Pads (4)
8 Short Screws (4)
9 Long Screws (4)
10 Nuts (4)
11 Spanner (1)
12 Allen Key (1)
Chassis
Length
Adjustment
Screw
Washers and bolts
5
2
3
4
6
1
Foot Pad
Length
Adjustment
Screws
8
7
9
10
11
Need Help? We’ve made a “Build your buggy” video guide for you...
Please visit: www.breezeboardpro.com/knowledge-base/ to view it.
OK, lets build your buggy...
1
Attach the 4 Rubber
Protector Pads to end of Arm Holders.
2
Add Velcro Straps to the Arm Holders through the Rubber
Protector Pads.
3
Nut
12
Use the 4 Long Screws to attach the Arms to the
Arm Holders & secure in place using the 4 Nuts with the Spanner & Allen Key.
Please ensure Nut i s on the outside.
Add Seat to the Seat
Platform using the 4 Short
Screws . No nuts required.
Tighten using the Allen Key .
5 6 7
4
Add Chassis Extender to the Seat Platform adjust to the correct length then tighten using the Chassis Length
Adjustment Screw.
With buggy upside down, add your
Breezeboard PRO to
Seat Platform and tighten Velcro Straps .
Flip the buggy back over and tighten the Foot
Pad Length Adjustment
Screws for each side to complete your
Breezeboard PRO buggy.
General Safety Information
Note: If the item is not assembled following the above instructions there could be risks of accident. Users ride at their own risk.
Learn to ride in a safe place on flat ground and away from obstacles. Stop completely before getting off. Ride on even ground. Ride in a safe and responsible manner. Do not attempt wheelies or tricks that could result in injury. Be aware of pedestrians, obstacles and uneven ground. Keep your Breezeboard PRO and Buggy clean, dry and free from debris. Be patient and take the time to practice before you ride in a congested environment. Be considerate to others when using your Breezeboard PRO & Buggy. Please make sure you wear a helmet, protective clothing such as elbow pads, knee pads and wrist guards and also gloves to protect your hands and fingers when riding.
Don’t ride through puddles. Don’t allow untrained riders to ride your Breezeboard PRO Buggy. Don’t ride in a careless manner as serious injury could occur from misuse or worse you could break your Breezeboard PRO Buggy. Don’t ride on sand or mud, it wont handle and we dont advise it. Don’t ride at full speed for prolonged periods as this can make it difficult for the Breezeboard PRO Buggy to maintain balance as well as cause unnecessary strain on the Breezeboard PRO components as well as risk your safety. It is not designed for high speeds. Only one person on the buggy at any one time. Please take your time to understand the controls of the Breezeboard PRO when the buggy is attached. Maintain safe stopping distances at all times. Maximum load 150kg. Users ride at their own risk.
Breezeboard PRO Limited, Unit 4 Chillfactore, Trafford Quays Leisure Village, Trafford Way, Manchester M41 7JA
Model: Buggy-01 Year of Manufacture: 2017 More information at: www.breezeboardpro.com
How to ride!
Before sitting on the buggy make sure the Breezeboard PRO is switched OFF.
After that sit on the seat making sure you are in a comfortable position.
Then raise the arms to the neutral position where the breezeboard is set horizontal to the ground. Then switch on the Breezeboard and you are ready to go! Always read the General Safety
Information first before riding and learn controls in a wide open space.
CONTROLS:
Push both handle bars down to go forward.
Pull both handle bars back to slow down, stop or reverse.
To turn, push one side down.
