VADT/VADR4900WDM A & E
B.
DIVISION 28 23 23
VAD7000 SERIES – FIBER OPTIC
TRANSMITTER AND RECEIVER
ENGINEERING SPECIFICATIONS
PART 1 - GENERAL
1.01 SUMMARY
A. Fiber Optic FM Video, Audio, and Data
Transceiver
1.02 SECTION INCLUDES
A. VAD7000 Series FM Video, Audio, and Data
Transceiver – Standalone
B. VAD7000 - R3 Series FM Video, Audio, and
Data Transceiver - Rack Mount
1.03 REFERENCES
A. Underwriters Laboratory (UL)
B. Underwriters Laboratory Canada (ULC)
C. European Union Compliance (CE)
1.04 SYSTEM DESCRIPTION
A. Performance Requirements: Provide a FM
Video, Audio, and Data Transceiver system that
transmits Bi-directional Video, Audio, Data.
1. The system shall utilize 850 nm optics
capable of simultaneous bi-directional
video, audio and data transmission on one
single mode optical fiber. (VAD7010-A)
2. The system shall utilize 850 nm optics
capable of simultaneous bi-directional
video, audio and data transmission on one
single mode optical fiber. (VAD7010-B)
3. The system shall utilize integrated WDM
optics operating at 850/1300nm capable of
simultaneous bi-directional video, audio and
data transmission on one single mode optical
fiber. (VAD7010WDM-A)
4. The system shall utilize integrated WDM
optics operating at 1300/850nm capable of
simultaneous bi-directional video, audio and
data transmission on one single mode optical
fiber. (VAD7010WDM-B)
1.05 SUBMITTALS
A. Product Data: Manufacturer’s printed product
data sheet for each type of Transmitter/Receiver
specified.
B. Detail Drawings: Electrical and optical connect
drawings. Product mounting template.
C. Manufacturer’s Installation and Operating
Manual: Printed installation and operating
information for each type of
Transmitter/Receiver specified.
D. Test Reports: Manufacturer’s Printed Test
Report via a Tektronics VM700A Video Test
Generator verifying product performance meets
or exceeds the specified product performance
referenced in Part 2.
E. Warranty: Manufacturer’s Printed Warranty
1.06 DELIVERY, STORAGE AND HANDLING
A. Deliver materials in unopened factory packaging
with Manufacturer’s bar coding to the job site.
Project name/project number/date
(Optional information, e.g., owner, A/E)
Inspect product upon delivery to assure that
specified products have been received.
C. Store in original packaging in a climate
controlled environment. Storage Temperature
not to exceed: -40˚ C to +85˚ C
1.07 PROJECT/SITE CONDITIONS
A. Temperature Requirements: Products shall
operate in an environment with an ambient
temperature range of –40˚ C to +74˚ C without
the assistance of fan-forced cooling.
B. Humidity Requirements: Products shall operate
in an environment with relative humidity of 0%
to 95% (non-condensing). If product is installed
in condensation conditions, unit shall have
conformal coating applied to the printed circuit
board.
1.08 WARRANTY
A. Standard International Fiber Systems
Comprehensive Lifetime Warranty: IFS
warrants the product to be free of factory defects
under manufacture’s Lifetime Warranty as
submitted under article 1.05 (E)
PART 2 - PRODUCTS
2.01 MANUFACTURER
A. Acceptable Manufacturer: International Fiber
Systems, Inc.; 16 Commerce Road, Newtown,
CT 06470 USA; Telephone: 203-426-1180; Fax
203-426-3326; Email: [email protected]; Internet:
www.ifs.com
B. Substitutions: Not Permitted
C. All fiber optic modules shall be supplied from a
single manufacturer.
2.02 MANUFACTURED UNITS
A. Model Number Descriptions: Reference Table
A: Product Number Descriptions
B. Model Compatibility Chart: Reference Table B:
Product Compatibility Chart
2.03 GENERAL SPECIFICATIONS
A. The FM Video, Audio, and Data Transceiver
system shall be an IFS VAD7000 series. The
module shall be capable of transmitting full color
video in real time in NTSC, PAL or SECAM
formats. The module shall support the
transmission of simplex or duplex audio as well
as RS-232 / RS-422 data. The module shall be
transparent to data protocols used by various
manufacturers, providing for universal
compatibility should future system expansion or
changes be required. The module shall require no
in-field electrical or optical adjustments or inline attenuators to ease installation. The module
shall transmit the video, audio and data signals
using frequency modulation of the optical signal.
The simultaneous video, audio and data
transmission shall utilize an integrated WDM for
increased stability and reliability of system
performance. The module shall provide power,
carrier detect, data transmit, data receive, audio
transmit, audio receive and video status
indicating LED’s for monitoring proper system
00000 - 1
Section Title
operation. The modules shall provide automatic
re-settable solid-state current limiters and
independent voltage regulators on each module
to reduce the chance of a single point failure of
the system. The module shall be hot swappable
in a rack mount system to reduce complete
system shut down during maintenance or repair.
The module shall have an MTBF of >100,000
hours and operate in an environment of –40˚ C to
+74˚ C and relative humidity between 0% to
95% (non-condensing). The module shall be UL
and ULC listed and CE marked. The circuit
board shall be UL 94 flame rated and meet all
PCI standards. All PC boards shall be designated
with part number, PC board number and show
appropriate revision number. Housing shall be of
all metal construction. All LED indicators and
both electrical and mechanical connections shall
be identified with silk-screened labels. The
module shall have a lifetime warranty to reduce
system life cycle cost in an event of a module
failure.
2.04 VIDEO SPECIFICATIONS
A. Input Video: 1 volt pk-pk (75 ohms)
B. Bandwidth: 5 Hz – 6.5 Mhz
C. Differential Gain: < 5 %.
D. Differential Phase: < 5°.
E. Tilt: <1%
F. Signal/Noise Ratio: >60dB
2.05 DATA SPECIFICATIONS
A. Data Interface: EIA RS-232, RS-422
B. Data Encoding: Unit shall be transparent to data
encoding (i.e. NRZ, NRZI, Manchester, Biphase)
C. Data Rate: DC-100 kbps (NRZ)
D. Operation Mode: Simplex or Full Duplex
2.05(B) AUDIO SPECIFICATIONS
E. Input/Output: 2.2 volts peak – to - peak
F. Bandwidth: 20 Hz – 20 kHz
G. Input/Output Impedance: 600
H. Total Harmonic Distortion: <1.0%
2.06 OPTICAL SPECIFICATIONS
A. IFS Model Number VAD7010
1. Optical Fiber: 62.5/125 micron Multimode
2. Number of Fibers Required: 2
3. Optical Wavelength: 850nm
4. Optical Power Budget: 14 dB
5. Optical Attenuation: No manual adjustments
required
B. IFS Model Number VAD7010WDM
1. Optical Fiber: 62.5 /125 micron Multimode
2. Number of Fibers Required: 1
3. Optical Wavelength: 850/1300nm
4. Optical Power Budget: 14 dB
5. Optical Attenuation: No manual adjustments
required
2.07 STATUS INDICATORS
A. Power: On/Red – Off/Off
B. Carrier Detect: Video Carrier Active/Yellow –
No Video Carrier/Off
Section Title
C. Data Transmit: Data Transmit/Green – No
Data/Off
D. Data Receive: Data Receive/Yellow – No
Data/Off
E. Audio Transmit: Audio Transmit/Green – No
Audio/Off
F. Audio receive: Audio Receive/Yellow – No
Audio/Off
G. Video In: Video In/Red – No Video/Off
2.08 CONNECTORS
A. Optical: ST
B. Power, Audio and Data: Terminal Block with
Screw Clamps
C. Video: BNC (Gold Plated Center-PIN)
2.09 ELECTRICAL SPECIFICATIONS
A. Power: 24 VAC CT
B. Current Protection: Automatic re-settable solidstate current limiters
C. Voltage Regulation: Solid-state, Independent on
each board
D. Circuit Board: UL 94 flame rated and meets all
PCI standards.
E. Rack mount Card: Shall be hot-swappable with
IFS Model Number R3 (EIA 19” card cage)
2.10 MECHANICAL SPECIFICATIONS
A. Surface Mount Dimensions:
VAD7010, VAD7010WDM: 7.” x 4.9” x 2.0”
(17.8 cm x 12.5 cm x 5.1 cm)
B. Rack Mount Dimensions:
VAD7010, VAD7010WDM: 7.7” x 5.0” x 2.0”
(19.6 cm x 12.7 cm x 5.1 cm)
C. Number of Rack Slots: 2
D. Finish: Module shall be constructed of a metal
enclosure with a powder coat finish model
Number F63B12 with all connections and
indicators silk-screened directly on unit. Rack
mount units shall be constructed of anodized
aluminum.
E. Weight: <2.0 lbs./1.0kg
2.11 ENVIRONMENTAL SPECIFICATIONS
A. MTBF: >100,000 Hours
B. Operating Temp: –40˚ C to +74˚ C
C. Storage Temp: -40˚ C to +85˚ C
D. Relative Humidity: 0% to 95% (noncondensing). If product is installed under
condensation conditions, unit shall have
conformal coating applied to the printed circuit
board. (Add –C to model number for conformal
coated printed circuit board)
2.12 REGULATORY AGENCIES/APPROVALS
AND LISTINGS
A. Underwriters Laboratory (UL) Listing Number:
I.T.E. 6D16
B. Underwriters Laboratory Canada (ULC) Listing
Number: I.T.E. 6D16
C. UL 94-flame rated PCB board: 94VO
D.
2.13 ACCESSORIES
00000 - 2
Project name/project number/date
(Optional information, e.g., owner, A/E)
A. Card Cage: IFS Model Number R3 (EIA 19”
card cage) shall be available to house and power
rack mount modules.
B. Blank Panels: IFS Model Number R3-BP shall
be available to cover unused rack slots.
PART 3 - EXECUTION
3.01 EXAMINATION
A. Inspect modules before installation.
B. Modules shall be free of any cosmetic defects or
damage.
C. All optical connectors shall be covered with dust
caps and remain on the module until installing
cable connectors to module.
D. Shipping box shall include the module, power
supply and operations manual.
3.02 PREPARATION
A. Standalone Module (Surface Mount)
1. Shall be mounted on a properly prepared
surface adequate for the size and weight of
module. The placement of the unit shall
allow provision for cable installation and
maintenance as indicated on the approved
detail drawings and in compliance with the
IFS mounting template and installation
manual.
B. Rack Mount Module (19” Rack)
1. Shall be installed in the IFS Model Number
R3 card cage. Ensure the card cage is
installed in a standard EIA 19” (482.6 mm)
rack or wall standoff bracket adequate for
the size and weight of the card cage. The
placement of the unit shall allow provision
for cable installation and maintenance as
indicated on the approved detail drawings
and in compliance with the IFS installation
manual.
C. Optical Fibers
1. Caution: NEVER look into the end of an
active optical fiber when using laser light
output. Eye damage can occur. Wear eye
protection when cleaving, terminating, and
splicing fiber.
2. The number and type (multimode or singlemode) of optical fiber shall meet the
requirements of the IFS model number in
article 2.06 used in the installation.
3. All optical fiber cables shall be properly
installed and terminated with the mating
optical connectors as submitted in article
2.08 (A).
4. The optical link shall be tested with either a
power meter, at a minimum, or OTDR to
Project name/project number/date
(Optional information, e.g., owner, A/E)
ensure the link budget (overall path loss)
plus an added 3dB of optical safety margin
does not exceed the optical power budget as
submitted in article 2.06.
5. All optical connectors on cable shall be
cleaned in compliance to optical connector
manufactures specifications and covered
with dust caps until connection to the fiber
optic module.
3.03 INSTALLATION
A. General: Locate fiber optic modules as indicated
on the approved detail drawings and install
module in compliance with the IFS installation
and operations manual.
3.04 TESTING
A. Testing the Fiber Optic Video Link.
1. Verify that the coax and optic fibers are
properly connected.
2. Make sure that power is applied to all fiber
optic modules, camera, and video monitor or
other equipment used in the system.
3. The carrier detect indicator LED should be
lit confirming a presence of a carrier signal.
4. Successful video link operation should be
visible at this point as witnessed by a good
quality video picture on the monitor.
B. Testing the Fiber Optic Audio Link
1. Verify that the audio leads and optical fibers
are properly connected.
2. Make sure that power is applied to all fiber
optic modules, Pre-amplifiers, amplifiers or
other equipment used in the system.
3. Successful audio link operation should be
confirmed at this point.
C. Testing the Fiber Optic Data Link.
4. Verify that the data leads and optical fibers
are properly connected.
5. Make sure that power is applied to all fiber
optic modules, controllers, and receiver
drivers or other equipment used in the
system.
6. Successful data link operation should be
confirmed at this point by using the
controller to pan, tilt, and zoom the camera
or communicate with other equipment.
3.05 CLEANING
A. Follow all instructions for proper use of solvents
and adhesives used for termination and splicing.
B. At completion of the installation, dispose of all
fiber scraps properly.
00000 - 3
Section Title
MANUFACTURED UNITS REFERENCE TABLES
Table A: Product Number Descriptions
VAD7000 SERIES
VAD7010
DESCRIPTION
MAX. DISTANCE*
MM Video / Audio / Data – 850 <> Video / Audio /
2.5 Miles (4KM)
Data – 850, 2 Fibers
VAD7010-R3
MM Video/ Audio / Data – 850 <> Video / Audio /
2.5 Miles (4KM)
Data – 850, 2 Fibers, Rack Mount
VAD7010WDM-A
MM Video / Audio / Data – 850 <> Video / Audio /
2.5 Miles (4KM)
Data – 1300, 1 Fiber
VAD7010WDM-A-R3
MM Video/ Audio / Data – 850 <> Video / Audio /
2.5 Miles (4KM)
Data – 1300, 1 Fiber, Rack Mount
VAD7010WDM-B
MM Video / Audio / Data – 1300 <> Video / Audio / 2.5 Miles (4KM)
Data – 850, 1 Fiber
VAD7010WDM-B-R3
MM Video/ Audio / Data – 1300 <> Video / Audio / 2.5 Miles (4KM)
Data – 850, 1 Fiber, Rack Mount
* Maximum distance is limited to optical loss of the fiber and any additional loss by connectors, splices and patch
panels.
Table B: Product Compatibility Chart
TRANSCEIVER
VAD7010
VAD7010-R3
VAD7010WDM-A
VAD7010WDM-A-R3
VAD7010WDM-B
VAD7010WDM-B-R3
COMPATIBLE TRANSCEIVER
VAD7010, VAD7010-R3
VAD7010, VAD7010-R3
VAD7010WDM-B, VAD7010WDM-B-R3
VAD7010WDM-B, VAD7010WDM-B-R3
VAD7010WDM-A, VAD7010WDM-A-R3
VAD7010WDM-A, VAD7010WDM-A-R3
END OF SECTION
Section Title
00000 - 4
Project name/project number/date
(Optional information, e.g., owner, A/E)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement