English - Hitachi Digital Media Group

English - Hitachi Digital Media Group
USER’S MANUAL
USER’S MANUAL
MANUEL UTILISATEUR
BEDIENUNGSANLEITUNG
MANUAL DEL USUARIO
MANUALE D’USO
BRUKSANVISNING
BRUKERHÅNDBOK
KÄYTTÖOPAS
BRUGERVEJLEDNING
GEBRUIKSAANWIJZING
ǼīȋǼǿȇǿǻǿȅ ȋȇǾȈȉǾ
UŽIVATELSKÁ PěÍRUýKA
PODRĉCZNIK UĩYTKOWNIKA
FELHASZNÁLÓI KÉZIKÖNYV
Colour LCD Monitor
Model Name
UT32MH70U
UT32MH70E
UT37MX70U
UT37MX70E
UT42MX70U
UT42MX70E
Model UT32MH70U is depicted.
READ THE ENCLOSED INSTRUCTIONS CAREFULLY.
KEEP THIS USER’S MANUAL FOR FUTURE REFERENCE.
Record the serial number of your monitor for future reference.
SERIAL NO.
This serial number is located on the back of the monitor.
Ver. 1
ENGLISH
USER’S MANUAL
Thank you for purchasing the Hitachi LCD Monitor.
Please read this user’s manual carefully before
operating this product.
To ensure proper operation, please read and follow ALL
the instructions, especially the “IMPORTANT SAFETY
INSTRUCTIONS” and “SAFETY PRECAUTIONS”.
Please keep this user’s manual for future reference.
Ver. 1
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .............1
INTRODUCTION................................................2
About This Manual ...................................................... 2
Trademark Credits ...................................................... 2
Software...................................................................... 2
Information for users applicable in European
Union countries ........................................................... 2
Features...................................................................... 2
SAFETY PRECAUTIONS ...................................3
Important for United Kingdom ..................................... 3
Explanation of the Symbols ........................................ 3
Cleaning and Maintenance ......................................... 7
Main Unit Installation .................................................. 8
Anti-tumble Measures ................................................. 8
ABOUT LCD PANEL ..........................................9
Common Characteristics of the LCD Panel ................ 9
SUPPLIED ACCESSORIES (including option)...10
COMPONENT NAMES .....................................11
Main Unit................................................................... 11
Remote Control......................................................... 12
PREPARATION ................................................13
Remote Control Battery Installation .......................... 13
Handling the Remote Control ................................... 13
Caution When Moving the Main Unit ........................ 13
CONNECTION .................................................14
1. Connect Power Cord to the Rear Panel ............... 14
2. Connect your External Equipment (if any)
to the Unit ............................................................. 14
Connecting Equipment with HDMI or
DVI Output Terminal........................................... 14
Connecting to Equipment with Video
Output Terminal.................................................. 15
Connecting to PC ............................................... 16
3. Attach Cushion, Secure with Clamps and Fit
Terminal Cover...................................................... 16
4. Connect the Power Plug into the Wall Socket ...... 17
BASIC OPERATION .........................................18
Power On/Off ............................................................ 18
Volume Up/Down ...................................................... 19
Mute .......................................................................... 19
Input Switching to HDMI and RGB ........................... 20
Input Signal Screen Display...................................... 20
SETUP OPERATION ........................................21
How to Use the On-Screen Display (OSD) System... 21
Select Language ....................................................... 21
Main Menu List ......................................................... 22
Watching Images from HDMI/Composite Input ........ 23
Setting Picture Adjustment .................................... 23
Reducing Noise ..................................................... 25
Making the Moving Image Smooth ........................ 26
Advanced Setting .................................................. 27
Viewing Images from a PC ....................................... 28
Setting Picture Adjustment .................................... 28
Advanced Setting .................................................. 29
FUNCTION ......................................................30
Size Switching .......................................................... 30
HDMI/Composite Signal Input ............................... 30
Display Size ....................................................... 30
Position Adjustment ........................................... 31
RGB Signal Input................................................... 31
Display Size ....................................................... 31
Power Save Mode .................................................... 32
When HDMI/Composite Input is Selected ............. 32
When RGB Input is Selected................................. 32
TROUBLESHOOTING ......................................33
When the Following Messages Appear
on the Screen ........................................................... 33
Symptom and Checklist ............................................ 33
PRODUCT SPECIFICATIONS ..........................36
Signal Input ............................................................... 37
Recommended Signal List ........................................ 38
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions thoroughly.
Please retain these instructions for future reference.
Heed all warnings and cautions to prevent potential danger.
Follow all instructions. Improper handling could cause personal injury and/or serious damage to the unit that may
shorten its service lifetime.
Do not block any ventilation openings.
Install the product in accordance with the manufacturer’s instructions.
If problems occur during installation or operation of the product, before calling for technical support or service
technicians, please read “TROUBLESHOOTING” ( 33 ~ 35 ) to determine the symptoms.
If serious problems occur (such as smoke or an abnormal odor from the unit), unplug the power cord, and then,
contact your local dealer immediately.
1
INTRODUCTION
ENGLISH
Thank you for purchasing the Hitachi LCD Monitor. We hope that you will enjoy the peak performance of this product.
This LCD Monitor has been designed to comply with international standards. However, it could cause personal injury
and property damage if improperly handled. In order to prevent potential danger and obtain maximum benefit from
your set, please observe the following instructions when installing, operating, and cleaning the product.
Keep this manual for future reference and record the serial number of your set in the space provided on the front
cover page of this manual.
About This Manual
The information in this manual is subject to change without notice.
This manual has been produced with the utmost care. If you have any comments or questions regarding this
manual, please contact your local dealer or our Customer Service Centre.
Before operating the set, please fully understand the prerequisites such as specifications or constraints for the
hardware and software. We are not responsible and accept no liability for any loss, damage or injury as a result of
misuse.
Reproduction, copying, utilization, modification and/or transmission in whole or in part of this manual are prohibited
except by prior written consent.
All other products and company names used in this manual are trademarks or registered trademarks of their
respective owners.
Trademark Credits
VGA and XGA are trademarks of International Business Machines Corporation.
VESA is a registered trademark of the Video Electronics Standard Association.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Even if no special note has been made of company or product trademarks, these trademarks have been fully
respected.
Software
It is illegal for you to alter, decompile, disassemble, decrypt, or otherwise reverse-engineer the software installed in
this product.
Information for users applicable in European Union countries
This symbol on the product or on its packaging means that your electrical and electronic equipment
should be disposed at the end of life separately from your household wastes. There are separate
collection systems for recycling in EU.
For more information, please contact the local authority or the dealer where you purchased the product.
Features
Ultra-slim-line LCD monitor.
Large-screen and high-definition LCD.
Enjoy high resolution display.
(32 inch model: 1366 (H) x 768 (V) pixels, the other size model: 1920 (H) x 1080 (V) pixels)
Improved digital signal processor.
High quality sound with deeper, richer and dynamic bass tones.
Accepts a digital input device with HDMI terminal.
Enjoy the image from your PC with a large, high-definition LCD screen.
Easy-to-use On-Screen Display system operated by remote control.
Low power consumption with power saving feature.
2
SAFETY PRECAUTIONS
For your safety, please read the following precautions carefully before using this product. Improper use would cause
serious personal injury and/or damage to your property or the product.
Important for United Kingdom
IMPORTANT FOR UNITED KINGDOM
WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS
The mains lead on this equipment is supplied with a molded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable
never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of
the plug. Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to
reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
WARNING: THIS EQUIPMENT MUST BE EARTHED
IMPORTANT
Green & Yellow
to Earth
The wires in the mains lead are coloured in accordance with the following code :
Green and Yellow = Earth, Blue = Neutral, Brown = Live.
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed
as follows:
Brown to Live
The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked
with the letter E or by the earth symbol
or coloured GREEN or GREEN and YELLOW.
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or
BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured
BROWN or RED.
Fuse
Cord Clamp
Blue to Neutral
Explanation of the Symbols
The following are the symbols used in this manual and affixed to the unit itself. Please fully understand the meanings
of the symbols before reading the instructions in this section.
WARNING
Never ignore the instruction. There are risks of serious or fatal injury to the user.
CAUTION
Do not ignore the instruction. There are risks of personal injury and/or property damage.
Other Symbols
The triangle with illustration is intended to alert the users that there are risks of fire, explosion, or high temperature if
the product is handled improperly.
Each illustration within the triangle specifies the contents in detail. (The figure on the left is an example.)
The circle with diagonal line and illustration indicates a prohibited action (the symbol to the left indicates that
dismantling is prohibited).
This symbol indicates a compulsory action.
The contents are clearly indicated in or adjacent to an illustration (the symbol to the left indicates that the power plug
should be disconnected from the power outlet).
3
SAFETY PRECAUTIONS (continued)
ENGLISH
WARNING
There is a risk of fire, electric shock, or serious injury.
ʄ If serious problems occur, unplug the power cord immediately.
Serious problems such as:
Smoke, abnormal odor or noise emitted from the product.
No picture, no sound or distorted picture on the display.
Foreign matter (such as water, metals etc.) entered the unit.
Do not continue using the product under these abnormal conditions.
Unplug the power cord, and contact your dealer immediately.
For your safety, never try to repair the product yourself.
Disconnect the
plug from the
power outlet.
ʄ Do not allow liquids or any foreign matter (such as metals or flammable items) to enter the unit.
If this does occur, unplug the power cord, and contact your dealer immediately.
Exercise special caution when young children are around the unit.
ʄ Do not remove covers, or modify the product.
High-voltage components are installed inside of the unit. Removing covers can expose you to high
-voltage electric shock, and other hazardous conditions.
Contact your local dealer to perform servicing such as inspection, adjustment or repair work.
Do not
dismantle.
ʄ Install the unit in a proper location where it does not expose anyone to danger.
If you bump against the edges of the unit, you could be injured.
ʄ Do not place any objects on top of the unit.
Objects such as:
Liquid containers (vase, fish tank, flowerpot, cosmetics or liquid medicine).
If water or any liquid spills onto the unit, it may cause short-circuiting and result in fire or electric shock.
If this occurs, unplug the power cord, and contact your dealer immediately.
Do not place anything heavy on top of the unit.
Do not climb on or hang from the unit.
Do not allow your pets to get on top of the unit.
ʄ Do not install the unit in an unsuitable location.
This could cause a malfunction or in extreme cases danger of electric shock. Locations where high
moisture is likely, such as bathrooms or shower rooms, close to windows, or outside where rain, snow
or other inclement conditions could occur, should be avoided. Please also avoid installing the unit in a
location where fumes from hot springs could come into contact with it.
4
SAFETY PRECAUTIONS (continued)
WARNING
There is a risk of fire, electric shock or serious injury.
ʄ Unplug the unit in the event of a lightning storm.
To reduce the risk of electric shock, do not touch the product when lightning occurs.
Disconnect the
plug from the
power outlet.
ʄ Do not do anything that may damage the power cord.
Do not damage, modify, twist, forcibly bend, heat, or pull excessively on the power cord.
Do not place heavy objects (including the unit itself) on top of the power cord.
If the power cord is damaged, contact your dealer for repairs or exchange.
ʄ Use only with designated power supply voltage.
To prevent the risk of fire and electric shock, operate the product only with the power supply voltage indicated on the
unit.
ʄ Be careful not to drop or allow any impact to affect the unit.
Take extra care whilst moving the unit.
There is no protection glass on the surface of the LCD panel. Therefore do not press the panel surface with your fingers
or hands. Also do not hit any objects against the monitor. These actions would damage the LCD cells or the panel
surface and could cause failure or personal injury.
In the event that you drop the unit or the cabinet is damaged, unplug the power cord and contact your local dealer
immediately.
Continuing use of the product under the above conditions may cause fire or electric shock.
ʄ Clean dust or metals from on or around the pins of the power plug regularly.
Continuing use of the product under the above conditions may cause fire or electric shock.
Always unplug the power cord first, then clean the pins using a dry cloth.
ʄ Do not place the unit on an unstable surface.
Unstable surfaces such as:
Tilted surface or shaky shelving, table, stand or trolley.
If the unit falls down, this could cause personal injury.
5
SAFETY PRECAUTIONS (continued)
ENGLISH
CAUTION
ʄ Do not place or use the unit in a dusty location.
This could cause a malfunction.
ʄ Do not cover or block any ventilation holes on the product.
The unit would overheat and this could cause fire or damage to the product which may shorten its service lifetime.
Install the product in accordance with the instructions in this manual.
Do not place the unit with the ventilation side downward.
Do not install the unit on carpeting or bedding.
Do not cover the unit with table cloths etc.
ʄ Be sure to ground the earth cable correctly.
Especially when you use a power cord adapter, be sure to connect the earth cable to the ground terminal. Incorrect
connection could cause fire or electric shock.
For your safety, always make sure to unplug the power cord before connecting or disconnecting the earth cable.
Connect the
earth cable.
ʄ Observe the anti-tumble measures described in this manual.
If the unit tumbles over, there is a risk of personal, possibly fatal injury. Also, this would damage the product seriously.
ʄ Do not install the unit near to medical devices.
To prevent malfunction of medical devices, do not use the product and medical devices in the same room.
ʄ Do not place a CRT-based television near the speakers of the LCD Monitor.
This could cause partial discoloration or blurring of the image on the CRT-based television.
Please install it away from the speakers of the unit.
ʄ Disconnect all of the external connection cables and detach the anti-tumble measures before
moving the unit.
Otherwise fire, electric shock or personal injury may result.
ʄ Connect the power plug securely.
Improper connection will cause overheating and may result in fire.
Do not touch the pins of the plug whilst connecting it to the wall socket. This could cause electric shock.
If the plug is not suitable for the wall socket, contact your dealer for replacement.
ʄ Do not handle the power cord with wet hands.
This could result in electric shock.
ʄ Do not pull the cord when you unplug the power cord.
This may damage the cord and could result in fire or electric shock.
Grip the plug when disconnecting it.
ʄ Unplug the power cord when you do not intend to use the product for long periods of time.
ʄ Handle the batteries properly.
Improper or incorrect use of the batteries may cause corrosion or battery leakage, which could cause fire, personal
injury or damage to property.
Use only the types of batteries which are indicated in this manual.
Do not replace batteries with used ones.
Install the batteries correctly by observing the polarity (+ and -) indications on the battery compartment.
Do not dispose of used batteries as domestic waste. Dispose of them in accordance with the local regulations.
6
SAFETY PRECAUTIONS (continued)
PRECAUTIONS
ʄ Do not install the unit in locations where it will be subjected to high temperature.
This could damage the cabinet or components of the product.
Do not install near any heat sources such as radiators, heating grilles, stoves, or other apparatus that produce heat.
Keep the unit out of direct sunlight. Otherwise the resulting increase in temperature of the unit may cause a malfunction.
ʄ Viewing Advice
The lighting of the environment in which the product is used should be appropriate. Too bright/dark environments are not good for
your eyes.
Take time to relax your eyes occasionally.
When you use the product, view from a distance equal to 3 to 7 times the height of the screen. This is the best viewing distance in
order to protect your eyes against eyestrain.
Adjust the volume to an appropriate level, especially during the nighttime.
ʄ Transporting the product
When the product needs to be transported due to moving or repair, use the carton box and buffer material that came with
the product.
Always transport the product upright; otherwise this could damage the panel glass or degrade the phosphors of the panel.
ʄ Keep radios away from the unit whilst in use.
The unit is designed to meet the international EMI standards to prevent radio interference. However, the unit
may generate noise in the radio.
If noise is heard on the radio, please try the following actions.
Adjust the direction of the radio antenna in order not to receive interference from the unit.
Keep the radio away from the unit.
ʄ Infrared communication devices
Infrared communication devices such as cordless microphones or cordless headphones may not operate properly around the unit.
This is because of communication failure. Please note that this is not a malfunction.
ʄ When you dispose of the product at the end of its service lifetime, follow the regulations in your residential area.
For more information, contact the local authority or the dealer where you purchased the product.
Cleaning and Maintenance
Please make sure to unplug the power cord before cleaning the unit.
ʄ How to clean the LCD panel of the unit.
Wipe the panel with a lint-free and dry cloth in order to prevent damage to the panel surface.
Do not use a chemical cloth or cleaners. Depending on the ingredients, these may cause discoloration and damage to the panel
surface.
Do not wipe with a rough cloth or rub hard. This may damage the panel surface.
In case of greasy dirt such as fingerprints, wipe the panel surface with a lint-free cloth moistened with a diluted neutral detergent
solution (dilute 1 part of detergent to 100 parts of water), and then wipe with a soft and dry cloth.
Do not use a spray cleaner. This could cause a malfunction.
ʄ How to clean the cabinet of the unit.
The following may cause cracking, deformation and peeling of paint.
Do not wipe the cabinet with benzene, thinners and other chemical products.
Do not spray volatile solutions such as insecticide over the cabinet.
Do not leave the cabinet in prolonged contact with plastic or rubber materials.
Do not use a chemical cloth, cleaner or wax. Depending on the ingredients, these may cause cracking and deformation.
Use a lint-free cloth (e.g. cloth for cleaning glasses) to clean the cabinet and control panel of the unit. In case of the excessive dirt,
wipe with a soft cloth moistened with a diluted neutral detergent solution and then wipe with a soft and dry cloth.
Never use the following detergents. They could cause cracking, discoloration and scratching.
Acidic/alkaline detergents, alcoholic detergents, abrasive cleaners, soap powder, OA cleaner, car wax, glass cleaner, etc.
7
SAFETY PRECAUTIONS (continued)
ENGLISH
Main Unit Installation
When installing the main unit, be sure to use the specified mounting units in order to obtain maximum performance
and maintain safety.
We assume no responsibility nor liability for personal injuries or property damage caused by use of other mounting
units or improper installation.
With respect to installation of the Tabletop stand, be sure to use the supplied Tabletop stand TS70T32KE for
UT32MH70U/E, TS70T37KE for UT37MX70U/E or TS70T42KE for UT42MX70U/E. Please read User’s manual
for the Tabletop stand very carefully before installation.
*The Tabletop stand is attached to the monitor in pictures in this User’s manual.
If using Wall or Ceiling Mounting units, contact your local dealer and ask for an approved installation specialist to
set up the unit. Never attempt to install it yourself. That could cause injury or damage.
Please make sure that there is adequate space around
the unit to prevent overheating.
Make sure not to block any ventilation holes.
Do not install the unit in a small space such as inside a
cabinet, closet or box.
Leave at least 10cm of clearance from each side of the
unit and 30cm from the top of the unit to ceiling.
10cm
or more
30cm
or more
10cm
or more
10cm
or more
10cm
or more
Anti-tumble Measures
Install in a stable location and take safety precautions against to ensure that the monitor does not fall.
Securing to a table
Please secure to a table after installing the Tabletop stand.
Fasten the fastening strap to a table using the wood screw provided.*
*The fastening strap and the wood screw are packed with the
Tabletop stand.
Wood screw
(4 x 20 screw) : 1 pc.
NOTE
Attach the fastening strap to the Tabletop stand before installing
the Tabletop stand to the monitor.
See User’s manual for the Tabletop stand about the procedure for
attaching.
Securing to ceiling or wall
Use the specified mounting unit to secure the set to a ceiling or wall.
NOTE
For more information regarding mounting of the unit, please contact your dealer.
Please install the unit in a proper location where it does not expose anyone to the danger of bumping themselves
(for example their hands, head or face, etc) against the edges of the unit and causing personal injury.
8
ABOUT LCD PANEL
Common Characteristics of the LCD Panel
The following are common phenomena occurring when operating the LCD Panel, due to its structural characteristics.
Please note that these are not malfunctions.
Defective Spots on Panel
The LCD panel is manufactured with high-precision technology. However, there might be some spots that are not
illuminated, or are brighter than others, or are in different colours, etc.
Surface on Panel
The LCD panel displays images by the fluorescent lamps internally. This can raise the temperature of the display
surface.
In addition, do not allow any heavy impact to affect the surface of the panel because the LCD panel is made using
fine processing glass.
Use Under Low Temperature Conditions
Because of the structural characteristics of the LCD panel, the response speed of the LCD panel becomes slower
when the ambient temperature around the monitor becomes too low. In some cases, this may result in a residual
image.
The residual image will disappear of its own accord as the temperature rises again to a normal level.
9
SUPPLIED ACCESSORIES (including option)
User’s Manual
Remote Control
12 13
ENGLISH
Check the supplied accessories before installation. In case of missing or damaged, please contact your dealer
immediately.
AA Size
Battery X 2
13
Quick Guide/
Translation of On-Screen
Display (OSD)
Power Cord
14 17
UK only
Except UK
* The type of power plug provided is different depending
on the model.
HDMI Cable
HDMI Cushion
The Control Panel Label
14 16 17
16
11
Terminal Cover
17
Tabletop Stand
TS70T32KE
(for UT32MH70U/E model),
TS70T37KE
(for UT37MX70U/E model)
or
TS70T42KE
(for UT42MX70U/E model)
Option:
D-sub15 pin - composite
cable (TP-RGBCV02 S)
Option:
D-sub15 pin - extension
cable (TP-ATRGB02)
15
16
Please read User’s
manual for tabletop stand
regarding installation.
10
COMPONENT NAMES
Main Unit
Front Panel
q
w
y
e
r
t
u
q
w
e
r
t
y
u
Cabinet
Panel
Remote Control Receiver
Indicating Lamp
Speaker
Illumination Lamp
Tabletop Stand
Control panel (on the underside)
[Example: 32 inch model]
l
;
(
i
o
a
s
d
f
)(
kj h g f
d s
a
o
i
OK) (Ż) (Ź) (ź) (Ÿ)
Power switch
Control Terminal*
Service use only
PC (RGB)/DVI Analogue Audio Input Terminal
PC Connection Terminal (D-sub 15 Pin)
Reset button (See 33 )
g
h
j
k
l
;
Ÿ button
ź button
Volume Up/Ź button
Volume Down/Ż button
Input Select/OK button
Menu/Return button
* The Control Terminal allows linked operation with a Hitachi Media Box which equips a control terminal with
logo.
The Control Panel Label
The supplied Control Panel Label will help you to recognise the function of each button on the Control Panel more
easily should you require it.
q Face the front panel of the monitor and peel the Control Panel Label from the back of the sheet but be careful
not to stick it to the monitor until you are sure of the correct position.
w Align the label with the bottom of the cabinet and slide it to adjust so that each marking on the label meets the
position of each button on the Control panel, and then press firmly to attach. Refer to the above diagram of the
Control panel about the position.
11
COMPONENT NAMES (continued)
ENGLISH
Main Unit (continued)
Rear Panel
q Power Cord Socket
w HDMI Input Terminal
wq
Please refer to
14 ~ 17
for detailed information regarding the connections.
Remote Control
Power On/Off
Press this button to switch
monitor On or Off standby.
Power Off
Press this button to switch
monitor Off standby.
RGB Input Select
Press this button to select
RGB (/Composite) input.
Menu
Cursor
Power On
Press this button to switch
monitor On.
Volume Up/Down
Mute
HDMI Input Select
Press this button to select
HDMI input.
Recall
Press this button to show the
input signal status.
OK
Input Select
Press this button to change
input mode.
HDMI
RGB (/Composite)
Auto Adjust
Press this button to adjust the
picture automatically in RGB
mode.
Return
Press this button to return to
the previous menu.
Picture Mode
Picture mode can be changed
each time pressed in the
following sequence.
Dynamic
Natural
Cinema
Size
Press this button to change
picture size.
12
PREPARATION
Remote Control Battery Installation
The remote control operates on 2 “AA” batteries.
1. Open the battery compartment cover
Slide open the battery compartment cover on the backside
in the direction of the arrow, and remove the cover.
Handling the Remote Control
Use the remote control within a distance of
about 5m from the front of the unit’s remotecontrol sensor and within an angle of about
30 degrees on both sides.
2. Install the batteries
Install 2 “AA” batteries (included)
making sure the polarities match
the indication inside the
compartment.
3. Close the battery
compartment cover
Within 30
degrees
Within 30
degrees
About 3m
About 3m
Make sure the projections
locate in the corresponding
holes and slide the
compartment cover until it
clicks shut.
About 5m
CAUTION
Risk of corrosion or battery leakage possibly resulting in physical injury
and/or property damage including fire.
Never mix used and new batteries in the device.
Replace all the batteries in the device at the same time.
Remove the batteries if the remote control is not going to be used for an extended period of time.
To avoid possible malfunction, read the following instructions and handle
the remote control correctly.
Do not drop or allow impact to affect the remote control.
Do not spill water or any liquid on the remote control.
Do not place the remote control on a wet surface.
Do not place the remote control under direct sunlight or near sources of excessive heat.
Caution When Moving the Main Unit
Whenever the unit is moved, two people are required to transport it safely.
Whenever the unit is moved,
it should be lifted forwards
by holding the top and base
on both sides of the unit for
stability.
13
CONNECTION
ENGLISH
The unit is suitable for various kinds of connections. Make a connection in the following steps. Be sure to unplug the
power cord from the wall socket first when connecting external equipment.
1. Connect power cord to the rear panel.
2. Connect your external equipment (if any) to the unit.
3. Attach cushion, secure with clamps and fit terminal cover.
4. Connect the power plug to the wall socket.
1. Connect Power Cord to the Rear Panel
Connect the power cord to the unit.
Do not connect the power plug to the wall socket until all other connections are completed.
2. Connect your External Equipment (if any) to the Unit
Connecting to Equipment with HDMI or DVI Output Terminal
The HDMI terminal can be connected to devices with HDMI output.
If the external device has a DVI output, this can be connected using an HDMI-DVI cable. If the HDMI-DVI cable is
used, connect analogue audio signal to the PC (RGB)/DVI Analogue Audio Input terminal.
Please be sure to attach the supplied cushion around the HDMI cable when connecting. See 16 .
[Example]
DVD-Player
IN
OUT
Set-Top Box
HDMI
[Example: 32 inch model]
AUDIO
(HDMI)
or
(HDMI)
(HDMI)
Camcorder
(DVI)
Home video game system
AUDIO
Information
The HDMI (High Definition Multimedia Interface) is a multimedia I/O interface. Only one cable is used to transmit all
video/audio/control signals, thus facilitating easy connection.
Moreover, the digital signals can produce high quality data without any degradation.
If your external device has an HDMI terminal, HDMI connection is recommended for higher quality picture and sound.
NOTE
PC (RGB)/DVI Analogue Audio Input terminal
This terminal can be used in either one of the following cases only.
q The external device is connected to the PC Connection
terminal of the unit.
w The DVI output of an external device is connected to the
HDMI terminal using an HDMI-DVI cable.
Make sure that the video and audio terminals are connected to
the same external device.
For details of the output format of an external device, refer to
“Recommended Signal List” on 38 .
We do not guarantee that all images from DVI connection can
be displayed properly.
HDMI terminal
PC (RGB)/DVI
Analogue Audio
Input terminal
PC Connection
terminal
14
CONNECTION (continued)
2. Connect your External Equipment (if any) to the Unit (continued)
Connecting to Equipment with HDMI or DVI Output Terminal (continued)
HDMI-Interfaced System
With “HDMI Control” function, you can interface the connected equipment through the HDMI terminal automatically
if the connected equipment meets an industry standard “HDMI CEC (Consumer Electronics Control)”.
1. Press the
button.
Function
HDMI Control
Auto Input Change Off
System Standby
Off
2. Select “Function” menu.
3. Select “HDMI Control”.
4. Select “Auto Input Change” or “System Standby”.
Select
Return
Exit
Condition: whilst the monitor is in Standby mode.
When the connected equipment starts (such as DVD
playback and Disc insertion), the monitor is automatically
turned On and switches the picture and audio to HDMI input.
Off
Auto Input Change
On
Condition: whilst the monitor is On.
When the monitor is switched off or set to Standby mode, the
connected equipment is also turned off or in Standby mode.
Off
System Standby
On
NOTE
If an HDMI-DVI cable is used, this HDMI-interfaced system is not available.
There may be a slight operation delay (e.g. switch On/Off the monitor or the connected equipment) when using
this “HDMI Control” function.
Please check if the connected equipment supports HDMI CEC and ensure that this operation is activated in the
connected equipment before using this “HDMI Control” function.
Connecting to Equipment with Video Output Terminal
The unit can be connected to equipments having video output using the optional D-sub 15 pin - composite cable.
[Example]
IN
OUT
*
VCR
DVD player
D-sub 15 pin
AUDIO
Set-Top Box
AUDIO
or
Camcorder
*Optional D-sub 15 pin - composite cable
[Example: 32 inch model]
Home video game system
NOTE
Refer to
15
27
for details of switching between RGB and Composite input.
CONNECTION (continued)
ENGLISH
2. Connect your External Equipment (if any) to the Unit (continued)
Connecting to PC
The PC connection terminal (D-sub 15 pin) + the PC (RGB)/DVI Analogue Audio Input terminal are connected
to the PC, allowing an analogue RGB signal.
IN
OUT
[Example]
D-sub 15 pin
AUDIO
AUDIO
or
[Example: 32 inch model]
How to connect from terminals on the Control panel (on the underside) to external equipment
To insert D-sub 15 pin, tilt the monitor forward and bring the terminals into view. 2 people are required to hold the
monitor and insert D-sub 15 pin safely. Be careful not to damage the panel.
*
*
[Example: 32 inch model]
[Example: Connecting to PC]
* You may wish to leave an optional D-sub 15 pin extension cable connected to this terminal to make future
connections easier.
3. Attach Cushion, Secure with Clamps and Fit Terminal Cover
1
Attach the supplied cushion around the HDMI cable.
Cushion
(supplied
accessory)
HDMI cable
2
Attach the cushion around
the HDMI cable so as not
to leave any clearance.
Unfasten 2 clamps, and then connect the HDMI cable and power cord
to the monitor through open clamps.
Clamp
HDMI cable
Power cord
16
CONNECTION (continued)
3. Attach Cushion, Secure with Clamps and Fit Terminal Cover (continued)
3
4
Secure the HDMI cable and power cord with clamps.
Clamp
Fit the terminal cover onto the monitor.
Insert the hook first to fit the terminal cover.
NOTE
When removing the terminal cover
Hook
Terminal Cover
Put your fingers into the terminal
cover and pull it up towards you.
4. Connect the Power Plug into the Wall Socket
Connect the power cord after completing all other connections.
(For some countries the type of plug is different that depicted.)
UK only
Except UK
CAUTION
Use only the power cord provided.
Do not use a power supply voltage other than that indicated (AC220-240V, 50Hz). It may cause fire or electric shock.
For the LCD monitor, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure
to connect the power cord to a three-pin grounded outlet and make sure that the cord is properly grounded. If you use
a power source converter plug, use an outlet with a ground terminal and screw down the ground line.
Ensure that both ends of the power cord are easily accessible.
If you have to change the power cord, please use a certified power cord that meets your region’s safety standards.
17
BASIC OPERATION
ENGLISH
Power On/Off
Turn On the power of the unit.
Illumination Lamp
To turn On the power to the unit:
Indicating Lamp
1. Press the Power switch on the unit.
The Indicating Lamp illuminates in Green, and the
Illumination Lamp turns into Blue.
The image will display on screen.
2. Once the Power switch is on, you can turn On/Off by
pressing the Power (On/Off, On, Off) button on the remote
control.
Power Switch
(on the underside)
To turn Off the power to the unit:
Front
1. Press the Power (On/Off, Off) button on the remote control.
The image disappears from the screen. The Indicating
Lamp turns into Red (Standby mode), and the Illumination
Lamp turns off.
2. Press the Power switch on the unit to completely turn Off
the power to the unit.
Rear
Power On/Off button
Power Off button
NOTE
Power On button
Whilst the Indicating Lamp illuminates in Red (Standby mode),
you can turn On/Off by pressing the Power (On/Off, On, Off)
button on the remote control.
The Indicating Lamp/Illumination Lamp Status
Indicating
Lamp
Illumination
Lamp
Power Status
Remark
Off
–
Off
–
Red
–
Standby mode
–
Green
Blue
On
Orange
–
Power Save mode
–
Refer to
32
and
33
for the condition.
NOTE
Whenever the monitor receives signal from the remote control, the indicating lamp blinks in green.
If the image does not appear on the screen at all, or if there is any problem with it, see “TROUBLESHOOTING” on
33 ~ 35 . This may help you to solve the problems.
After turning On, it takes about 6 seconds until the monitor starts up. Please note that buttons on the remote control
and the unit (such as the Power button) do not work during this period of time.
Do not switch the power On/Off repeatedly within a short period of time. It could cause a malfunction.
If a power cut occurs during use of the unit, to avoid sudden surges of electricity when the power comes back on,
unplug the power cord before leaving home.
18
BASIC OPERATION (continued)
Volume Up/Down
1. To increase the sound volume, press the Volume Up button
on the remote control or control panel.
The Volume Indicator value on the screen will shift to the
right.
Volume Up/Down
button
Mute button
2. To decrease the sound volume, press the Volume Down
button on the remote control or control panel.
The Volume Indicator value on the screen will shift to the
left.
Mute
1. To mute sounds, press the
button on the remote control.
The sound of the unit is temporarily turned Off.
The colour of the Volume Indicator will turn into grey
whilst muting the volume.
2. To turn the sound back on, press the
button again, or
press the Volume Up button on either the remote control or
control panel.
The colour of the Volume Indicator will turn back to blue.
NOTE
You can decrease the volume by pressing the Volume Down
button whilst the sound is muted.
19
Volume Up/Down button
20
BASIC OPERATION (continued)
ENGLISH
Input Switching to HDMI and RGB
By pressing the Input Select button, you can switch the input to display
the image outputting from the external equipment connected to each
terminal (HDMI and RGB (/Composite)).
HDMI Input
Select button
<From Remote Control>
Press the
button on the remote control.
RGB Input
Select button
Each time this button is pressed, the screen displays the
corresponding mode in the following sequence.
HDMI
Press the
or
Menu button
RGB (/Composite)
button to directly select the input mode.
<From Control panel>
The Input modes can also be switched using the Input Select button on
the control panel.
Each time this button is pressed, the screen displays the corresponding
mode in the following sequence.
HDMI
Input Select
button
RGB (/Composite)
NOTE
Menu button
Switching between RGB and Composite Input.
Input Select button
When pressing the
button, you will see the image from either RGB or Composite input.
You can set up the mode in advance if necessary.
1. Press the
button.
2. Select “Setup” menu in RGB or Composite mode.
3. Select “RGB Input”.
Select “Composite” to display the image from video output via the optional D-sub 15 pin – composite cable.
Select “RGB” to display the image from PC.
See 27 and 29 for details of “RGB Input” menu.
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the
The display will go out in approximately 6 seconds.
HDMI mode
RGB mode
Composite
mode
HDMI
DVI
720R
RGB
H : 48.4kHz
V : 60.0 Hz
Composite
button on the remote control.
Input mode
*HDMI - DVI connection only
Signal mode
Input mode
Input horizontal
frequency
Input vertical
frequency
Recall
button
Input mode
20
SETUP OPERATION
How to Use the On-Screen Display (OSD) System
You can use the On-Screen Display system to access the various kinds of the features and functions.
Basic Operation
Picture
Audio
Function
Setup
Language
Select OK Set
◄►
1. Press the
button on the remote control or the Menu button on the
control panel of the unit. The Main Menu is displayed on the screen as
shown on the right.
2. To select the item, press the
button.
The selected item will be highlighted in Yellow.
<Main Menu>
◄►
3. Press the OK button to set your selection.
The selected menu page will be displayed on the screen.
4. Use the
Press the
5. Use the
button to choose the item on the menu page.
OK
◄►
Press the
Menu button
button to set your selection.
button to adjust the item values or choose options.
OK
button to set your selection.
6. To exit from the menu, press the
button.
NOTE
The OSD menu screen will be closed automatically when no operation has
been made for about one minute.
If the item on the menu is shown in grey, it means that it cannot be selected
or adjusted.
Menu button
Select Language
Select the language from the list so that the OSD menu can be displayed in the selected language.
How to set Language
2. Select your preferred language from the list using the
The selected item will be highlighted in Yellow.
◄►
1. Enter the “Language” menu from the Main Menu.
button.
3. Press the OK button to set your selection.
The mark on the left turns into a double circle when the selection is fixed.
4. Press the
21
button to exit from the entire OSD menu.
Language
‫ޓޓޓޓޓ‬English
‫ޓޓޓޓޓ‬English (US)
‫ޓޓޓޓޓ‬Français
‫ޓޓޓޓޓ‬Español
‫ޓޓޓޓޓ‬Deutsch
‫ޓޓޓޓޓ‬ᣣᧄ⺆
‫ޓޓޓޓޓޓ‬૕ਛᢥ
‫❥ޓޓޓޓޓ‬㜚ਛᢥ ‫ޓޓޓޓޓ‬
Select
OK Set
Return
SETUP OPERATION (continued)
ENGLISH
Main Menu List
• Please refer to supplied “Translation of On-Screen Display (OSD)” to check translation of menu items.
Menu
Picture
(HDMI/Composite)
Picture (RGB)
Audio
Function
Select between 3 picture modes according to the lighting condition.
Contrast
Adjust to increase or decrease the picture contrast.
23
Brightness
Adjust to brighten or darken the picture.
23
Colour
Adjust to increase or decrease the colour density.
23
Sharpness
Adjust to sharpen or soften the picture.
23
Hue
Adjust to obtain natural skin colour.
23
Colour Temperature
Select between 3 settings according to your preferred colour tone.
23
Back Light
Adjust to increase or decrease the brightness of back light on LCD panel.
23
Reset
Reset each item on the menu screen to the factory setting.
23
Deep Colour
Enhance the colour depth of picture.
24
Select between 3 contrast modes to suit your preference.
24
3D Colour Management
Adjust the suitable tint, colour density, and brightness on image.
24
Black Enhancement
Adjust the black level compensation.
24
DNR
Reduce noise for picture signal.
25
MPEG NR
Reduce mosquito noise in the picture.
25
Cross Colour NR
Reduce noise caused by colour mixture of adjacent pixels.
25
Game Mode
Reduce the time-lag of speed on the moving image during TV game play.
15
Film Mode
Adjust to make the moving image smooth.
26
3D Comb Filter
Reduce the colour blurring to reproduce purer colour.
24
Reset
Reset each item on the menu screen to the factory setting.
24
Colour Temp. Adjust
Set specific adjustment in each of 3 colour temperature modes.
24
Contrast
Adjust to increase or decrease the picture contast.
28
Brightness
Adjust to brighten or darken the picture.
28
Colour
Adjust to increase or decrease the colour density.
28
Hue
Adjust to obtain natural skin colour.
28
Colour Temperature
Select between 3 settings according to your preferred colour tone.
28
Colour Temp. Adjust
Set specific adjustment in each of 3 colour temperature modes.
28
Back Light
Adjust to increase or decrease the brightness of back light on LCD panel.
28
Reset
Reset each item on the menu screen to the factory setting.
28
Treble
Adjust to increase or decrease the level of treble. (-15~+15)
-
Bass
Adjust to increase or decrease the level of bass. (-15~+15)
-
Balance
Adjust the balance of sound from the bottom right and left speakers. (-10~+10)
-
Surround
Select surround-sound. (Off/On)
-
Bass Boost
Enhance bass sounds. (Off/On)
-
Clear Voice
Select clearer and more realistic sounds. (Off/On)
-
Perfect Volume
Adjust sound volume appropriately. (Off/On)
-
Speakers
Select if using internal speakers. (Off/On)
-
Reset
Reset each item on the menu screen to the factory setting.
-
System
This function is not available.
-
Auto Input Change
HDMI Control
System Standby
Setup (RGB)
Language
23
Contrast Mode
Video Power Save
Setup
(HDMI/Composite)
Page
Picture Mode
In response to the connected equipment (such as DVD) through HDMI cable, the
monitor is automatically turned On and switched to HDMI input.
In response to the monitor, the connected equipment (such as DVD) through HDMI
cable is automatically turned Off (standby mode).
15
15
Save power consumption when no signal can be input in HDMI/Composite input mode.
32
RGB Input
Select the effective signal.
27
Colour System
Select colour system.
27
Auto Adjust
Adjust Horizontal Position, Vertical Position, Horizontal Clock, and Clock Phase
automatically.
29
Horizontal Position
Adjust the display position horizontally.
29
Vertical Position
Adjust the display position vertically.
29
Horizontal Clock
Minimize the vertical stripes on the screen.
29
Clock Phase
Minimize the blurring of the letters and stripes on horizontal row.
29
Reset
Reset each item on the menu screen to the factory setting.
29
Frequency Display
Set On for PC signal frequency information to be displayed on the Input Signal Screen
Display.
29
WXGA Mode
Select the resolution when WXGA signal is received.
29
RGB Input
Select the effective signal.
29
-
21
NOTE
Some of the menus’ contents are different depending on the model. Please refer to “Setup hint” on the following pages.
The menu setting can be stored for each of inputs except “Picture Mode”.
22
SETUP OPERATION (continued)
Watching Images from HDMI/Composite Input
1. Connect to external equipment. (See
14
and
15
for details.)
2. Press the
or
button to switch to HDMI mode.
Press the
or
button to switch to composite mode.
3. Press the
button.
Setting Picture Adjustment
You can adjust the display condition such as colour settings.
Select “Picture” from Menu list.
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Back Light
Reset
Select OK Set
Picture
Dynamic
+31
–31
0
+15
0
Normal
+20
Reset
Return
Dynamic
Deep Colour
Contrast Mode
3D Colour Management
Black Enhancement
DNR
MPEG NR
Cross Colour NR
Game Mode
Film Mode
3D Comb Filter
Reset
Select OK Set
Picture
Colour Temp. Adjust
Off
Normal
Off
Off
Off
Off
Off
Off
Off
Off
Reset
Return
Select
OK Set
Dynamic
Return
* The OSD screen may be different depending on the model.
Selected Items
Setup hint
Dynamic
Picture Mode
Natural
Cinema
Contrast
-31~+31
(+32~+40)
This adjusts the contrast to meet the surrounding
brightness by using the ◄► button.
The maximum value is extended up to [+40] by pressing
button for more than 2 seconds at [+31]. The
the
value between [+32] ~ [+40] appears in magenta. This is
the special feature for dark images, so it is recommended
to set the value less than [+31] under normal conditions.
Brightness
-31~+31
Adjust brightness according to personal preference by
using the ◄► button.
Colour
-31~+31
Adjust colour according to personal preference by using
the ◄► button.
Sharpness
-15~+15
Preferred sharpness can be adjusted by pressing the
button for softer image or the
button for sharper image.
Hue
-31~+31
Pressing the
button enhances red and weakens green,
whilst pressing the
button weakens red and enhances
green. The setup hint is to adjust for realistic skin colour.
Cool
Colour Temperature
Normal
Warm
Back Light
Reset
23
You can make the best selection from 3 modes depending
on the lighting condition and intended use.
Dynamic: Suitable for brighter conditions.
Natural : Suitable for normal lighting conditions.
Cinema : Suitable for watching movies.
-20~+20
You can select from 3 settings depending on the colour
condition using the ◄► button.
This is not available when “Deep Colour” is “On” in HDMI
mode.
Adjust the brightness of the Back Light for maximum
visibility.
Each item on this menu screen can be restored to the
factory settings by pressing the
OK
button.
SETUP OPERATION (continued)
ENGLISH
Watching Images from HDMI/Composite Input (continued)
Setting Picture Adjustment (continued)
Selected Items
Setup hint
Off
Deep Colour
On
Dynamic
Normal
Contrast Mode
Linear
Off
3D Colour Management
On
Enhance the colour depth of picture during HDMI input.
This is not available for UT32MH70U/E model.
Please check if the connected equipment supports Deep
Colour and ensure that this operation is activated in the
connected equipment before using this function.
It allows you to choose from 3 modes.
Dynamic: Sharpen the gradation to improve the contrast
feeling.
Normal : Improve the contrast feeling to reproduce a
faithful gradation.
Linear : Reproduce as faithful gradation as possible.
This is not available when “Deep Colour” is “On” in HDMI
mode.
On : It automatically adjusts the suitable tint, colour density,
and brightness on images.
Off : Set it off if the image does not look natural.
This is not available when “Deep Colour” is “On” in HDMI
mode.
Off
Low
Black Enhancement
Middle
Adjusts the black level compensation.
This is not available when “Deep Colour” is “On” in HDMI
mode.
High
Off
Game Mode
On
Off
Low
3D Comb Filter
Middle
High
This is available only when using D-sub 15 pin - composite
cable.
This reduces the dot and colour blurring in minute scales
so that it can reproduce purer colour.
This is not available for NTSC4.43, PAL60, SECAM,
PAL-N and PAL-M system.
This is available only when receiving NTSC/PAL
composite signal.
Each item on this menu screen can be restored to the
factory settings by pressing the OK button.
Reset
Amplitude
Red
Green
Colour Temp. Adjust
During TV game play, you can reduce the time-lag of
speed on the moving image.
This function is not available for UT32MH70U/E.
On
Blue
Cut Off
Red
Green
Blue
Off
On: When you want to set specific adjustments in each of
the 3 Colour Temperature modes. You can adjust on
the Amplitude and Cut Off. The settings reflect on the
Colour Temperature.
Amplitude: Subdue the colours (Red/Green/Blue) on
the brighter parts (-63~0).
Cut Off : Subdue the colours (Red/Green/Blue) on
the darker parts (-31~+31).
Off: Remains as default setting.
This is not available when “Deep Colour” is “On” in HDMI
mode.
24
SETUP OPERATION (continued)
Watching Images from HDMI/Composite Input (continued)
Picture
Reducing Noise
Deep Colour
Contrast Mode
3D Colour Management
Black Enhancement
DNR
MPEG NR
Cross Colour NR
Game Mode
Film Mode
3D Comb Filter
Reset
Select OK Set
You can reduce the unwanted picture noise.
Select “Picture” from the Menu list.
Dynamic
Off
Normal
Off
Off
Off
Off
Off
Off
Off
Off
Reset
Return
* The OSD screen may be different depending on the model.
Selected Items
Setup hint
Off
DNR
Low
Middle
This is a noise reduction system for picture signals.
High
Off
MPEG NR
Low
This is a noise reduction system for MPEG picture signals.
(e.g. against mosquito noise and block noise.)
High
Off
Cross Colour NR
Low
High
25
This reduces noise caused by colour mixture of adjacent
pixels.
This is not available when “Game Mode” is On.
This is not available for UT32MH70U/E model.
SETUP OPERATION (continued)
Picture
Making the Moving Image Smooth
Using this function helps to make the moving image smooth.
Select “Picture” from the Menu list.
Deep Colour
Contrast Mode
3D Colour Management
Black Enhancement
DNR
MPEG NR
Cross Colour NR
Game Mode
Film Mode
3D Comb Filter
Reset
Select OK Set
ENGLISH
Watching Images from HDMI/Composite Input (continued)
Dynamic
Off
Normal
Off
Off
Off
Off
Off
Off
Off
Off
Reset
Return
* The OSD screen may be different depending on the model.
For UT32MH70U/E:
Selected Items
Setup hint
Off
Film Mode
On
On: Automatically identifies if it is a movie and faithfully
reproduces the original film images.
Off: Set to Off if the image does not look natural.
This is available only when receiving NTSC, 480i, PAL,
SECAM, 576i, or 1080i input signals.
For UT··MX70U/E:
Selected Items
Setup hint
Off
Original
Film Mode
Smooth1
Smooth2
NOTE
This helps to make the moving image smooth.
Original: Automatically identifies the source of movie (3:2
pulldown, 2:2 pulldown) and faithfully reproduces
the original film images.
Smooth1: Automatically identifies the source of movie (3:2
pulldown, 2:2 pulldown) and reproduces the
smooth motion.
Smooth2: Reproduces the clear moving image when the
input signal is 50Hz or 60Hz.
Off: Set to Off if the image does not look natural.
This is not available in the following cases.
OSD is displayed.
“Game Mode” is On.
About “Film Mode”
The image might not look natural depending on the image contents.
Phenomena such as
q When switched to the subtitles of a film or images, the image displays fine horizontal streak lines.
w When switched to scenes such as commercial and animation, the image displays fine horizontal streak lines.
e When displaying a ticker or subtitle, the text on the image becomes rough (aliasing).
r When watching the image in Composite mode, which is connected to any external equipment, the OSD of
external equipment displays fine horizontal streak lines.
These phenomena occur due to the method of converting the image. Please note that this is not a malfunction. In
the event that this is disturbing, please set to Off.
In addition, the effect of this menu might vary depending on the size setting (See 30 ).
Also, this might be ineffective depending on the scene of the image.
26
SETUP OPERATION (continued)
Watching Images from HDMI/Composite Input (continued)
Setup
Video Power Save
RGB Input
Colour System
Advanced Setting
Select “Setup” from the Menu list.
Select
On/Off
Off
Composite
Auto
Return
VC143-141 06-0
[Example]
Selected Items
Setup hint
Off
Video Power Save
On
See
32
for details.
RGB
RGB Input
Select the effective signal.
Composite
Auto
PAL
SECAM
NTSC 4.43
Colour System
NTSC 3.58
PAL60
Selects the colour system depending on the input signal.
Generally, select [Auto] to receive all signals.
If the input signal has too much noise, the signal level is
too low or the operation is unstable in [Auto], select the
system according to the colour system of the input signal.
Composite input only.
PAL-M
PAL-N
NOTE
Watching through the optional D-sub 15 pin - composite cable
If your external equipment does not have an HDMI terminal or a DVI terminal, you can watch images from your
external equipment through the optional D-sub 15 pin - composite cable.
1. Connect to your external equipment with the optional D-sub 15 pin - composite cable. (See
2. Switch to RGB input by pressing the
3. Press the
or
15 )
button.
button and select “Setup” from the menu list.
4. Select “Composite” in “RGB Input”.
NOTE
Checking software version
The software version is displayed on Setup (HDMI/Composite) menu.
Setup
Video Power Save
RGB Input
Colour System
Select
On/Off
Off
Composite
Auto
Return
VC143-141 06-0
Software version
[Example]
27
SETUP OPERATION (continued)
1. Connect to the PC. (See
16
for details of connection to PCs.)
2. Switch to RGB input by pressing the
3. Press the
ENGLISH
Viewing Images from a PC
or
button.
button.
Setting Picture Adjustment
You can adjust the display condition such as position adjustment and colour settings.
q “Picture” Menu
Select “Picture” from the Menu list.
Picture
Contrast
+31
Brightness
–31
Colour
0
Hue
+31
Colour Temperature Normal
Colour Temp. Adjust
Back Light
+20
Reset
Reset
Select
Selected Items
Return
Setup hint
-31~+31
(+32~+40)
Contrast
OK Set
This adjusts the contrast to meet the surrounding
brightness using the ◄► button.
The maximum value is extended up to [+40] by pressing
the
button for more than 2 seconds at [+31]. Values
between [+32] ~ [+40] appear in magenta. This is the
special feature for dark images, so it is recommended to
set the value less than [+31] under normal conditions.
Brightness
-31~+31
Adjust the brightness according to personal preference
using the ◄► button.
Colour
-31~+31
Adjust the colour according to personal preference using
the ◄► button.
Hue
-31~+31
Pressing the
button enhances red and weakens green,
whilst pressing the
button weakens red and enhances
green. These adjustments are for realistic skin colour.
Cool
Colour Temperature
Normal
You can select from 3 settings with the
◄►
button.
Warm
Colour Temp. Adjust
On
Amplitude
Red
Green
Blue
Cut Off
Red
Green
Blue
Off: Remains as default setting.
Off
Back Light
Reset
On: When you want to set specific adjustments in each
of the 3 colour temperature modes. You can adjust
the Amplitude and Cut Off. The settings reflect on the
Colour Temperature.
Amplitude: Subdues the colours (Red, Green, Blue) on
the brighter parts (-63~0).
Cut Off : Subdues the colours (Red, Green, Blue) on
the darker parts (-31~+31).
-20~+20
Adjusts the brightness of Back Light for maximum visibility.
Each item in the “Picture” Menu can be restored to the
factory setting by pressing the OK button.
28
SETUP OPERATION (continued)
Viewing Images from a PC (continued)
Setting Picture Adjustment (continued)
Setup
Auto Adjust
Adjust
Horizontal Position
0
Vertical Position
+31
Horizontal Clock
–20
Clock Phase
+10
Reset
Reset
w “Setup” Menu
Select “Setup” from the Menu list.
Select
Selected Items
Return
Exit
Setup hint
Adjusts Horizontal Position, Vertical Position, Horizontal
Clock, and Clock Phase automatically.
Press the OK button to start automatic adjustment as
necessary. The message “Auto Adjusting” is displayed.
The image might not be adjusted to its optimum condition
depending on the types of signals. In that case, adjust
each item manually.
Auto Adjust
Horizontal Position
-63~+63
Adjusts the display position horizontally.
When the value exceeds a possible range, it will be
displayed in magenta.
Vertical Position
-31~+31
Adjusts the display position vertically.
When the value exceeds a possible range, it will be
displayed in magenta.
Horizontal Clock
-31~+31
Minimizes vertical stripes on the screen.
Clock Phase
0~+63
Minimizes the blurring of letters and stripes on horizontal
row.
Be sure to adjust Horizontal Clock before adjusting Clock
Phase.
When the value exceeds a possible range, it will be
displayed in magenta.
Each item in “Setup” Menu can be restored to the factory
setting by pressing the OK button.
Reset
Setup
Frequency Display
WXGA Mode
RGB Input
Advanced Setting
Select “Setup” from the Menu list and skip to the second page.
Select
Off
Off
RGB
On/Off
Return
* The OSD screen may be different depending on the model.
Selected Items
Frequency Display
Setup hint
Off
On
Set to On for PC signal frequency information to be
displayed on the Input Signal Screen Display.
Off
WXGA Mode
1280X768
Selects the resolution when a WXGA signal is received.
1360X768
RGB
RGB Input
Selects the effective signal.
Composite
29
FUNCTION
ENGLISH
Size Switching
Each time the
button of the remote control is pressed, the screen display size is
switched in sequence, and the status will be displayed at the bottom of the screen.
HDMI/Composite Signal Input
Size button
Display Size
Watching Standard Definition Pictures (480i, 480p, 576i, 576p, Composite)
4:3
Panoramic 1
Panoramic 2
Zoom 1
Full
Zoom 2
Watching High Definition Pictures (720p, 1080i, 1080p)
Full 1
Full 2
Zoom
You can display the image at its optimum condition by selecting display size depending on the current output image
as shown below.
Input Signal
Display
Screen
Display Size
To display suitable screen as follows.
When Watching Standard Definition Pictures:
4:3
Plays a 4:3 image on screen faithfully. Blanking occurs on
both sides.
Panoramic 1
Plays a 4:3 image which enlarges horizontal and vertical size of
the middle in equal scales, and displays both sides appearing
much wider.
Panoramic 2
The vertical size of Panoramic1 is reduced so that you can
see the whole image, including any subtitles, that might
otherwise not be fully visible on the screen.
Zoom 1
Plays a 16:9 image in 4:3 frame (Vista size) faithfully.
*In some cases, slight blanking may remain at the top and
bottom.
Zoom 2
Plays a 21:9 image in 4:3 frame (Cinema size) expanding
vertically.
*In some cases, slight blanking may remain at the top and
bottom.
(4:3 Signal)
(Vista)
(Cinema)
Full
Plays a 4:3 image faithfully in the standard vertical size and
horizontally squeezed.
(Squeeze)
When Watching High Definition Pictures:
(16:9 Signal)
(4:3 Image in
16:9 Frame)
Full 1
Plays a 16:9 image faithfully showing 95% of the size.
Full 2
Plays a 16:9 image faithfully showing 100% of the size.
*In some cases, the screen display has unnecessary
blanking or noise at the edges.
Zoom
Plays a 4:3 image in 16:9 frame by enlarging a 4:3 image to fill
the 16:9 screen.
30
FUNCTION (continued)
Size Switching (continued)
HDMI/Composite Signal Input (continued)
Position Adjustment
1. Press the
◄►
Vertical picture position can be adjusted for Panoramic 1, Zoom 1 and Zoom 2 mode as follows.
button whilst operating the picture size display.
◄►
2. “Position” display will appear.
3. Adjust the position using the
button.
The adjustment ranges of each picture size are as shown below.
Display Size
Adjustable Range
Panoramic 1
-12~+12
Zoom 1, Zoom 2
-31~+31
Position + 31
Position - 31
PressŸ
Pressź
CAUTION
Using a wide-screen monitor
The monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain
software, such as a TV programme, the image would appear different from the original. Take this into
consideration when making screen mode choices.
Use of the wide feature displaying enlarged pictures in coffee shops, hotel and other establishments for commercial
or public viewing purposes could infringe on the copyright holder’s rights, which are protected by Copyright Law.
When a normal 4:3 image (not wide screen) is displayed over the entire screen in the Panoramic mode, the
peripheral image may disappear partly and/or appear distorted in some cases. Use 4:3 mode to view the image
reflecting the original intention.
RGB Signal Input
Display Size
You can select a suitable size depending on the resolution.
Normal
Full
Real*
* Real mode gives the image with same shapes as that of a
computer monitor (neither compression nor stretching). This
mode is not available if the input signal is 1280 x 1024 (SXGA)
in the UT32MH70U/E model.
Display Area Selection Diagram
Resolution
Display
640 X 480 (VGA)
800 X 600 (SVGA)
1024 X 768 (XGA)
1280 X 1024 (SXGA)
640 X 400 (VGA)
1280 X 768 (WXGA)
1360 X 768 (WXGA)
31
Input signal
Full display
Full
Circular display
Normal
Real*
FUNCTION (continued)
ENGLISH
Power Save Mode
When HDMI/Composite Input is Selected
You are provided the function to save power consumption when no signal is
detected in HDMI/Composite input. Set to On in “Video Power Save” from the
Setup Menu, which leads to the power save mode.
1. Press the
Setup
Video Power Save
RGB Input
Colour System
Select
button when in HDMI/Composite input.
2. Select the “Setup” menu and press the
OK
On/Off
Off
Composite
Auto
Return
button.
3. Select “Video Power Save”.
Off
On
Video Power Save
When no signal is detected
Condition
Indicating Lamp
When signal is input during
On in “Video Power Save”
Power Save
Orange
Turns On automatically.
When RGB Input is Selected
When the unit is connected to a VESA DPMS computer, the Power Save mode (Operation mode: Off) can be set to
be activated automatically when the computer is not being used, in order to reduce the power consumption of the
unit.
RGB sync signal
Horizontal
Yes
No
Yes
No
Vertical
Yes
Yes
No
No
PC signal
Active (normal display)
Operation mode
On
Blank (no display)
Off
Indicating lamp
Lights green
Lights orange
To return to operating status, operate the personal computer, or press either the Input Select button on the control
panel or the
or
button on the remote control.
32
TROUBLESHOOTING
Before calling a service technician, check the following tables first. If the problem cannot be solved with the
suggested procedures, contact your local dealer. For your safety, NEVER try to repair the product yourself.
When the Following Messages Appear on the Screen
Message
Condition / Action
Power Save
This indicates it is in Power Save mode. (in HDMI/RGB/Composite input)
This message appears 5 seconds before Power Save mode starts.
The indicating lamp lights in orange.
No Sync. Signal
The unit cannot detect any signals from any input terminals.
Check if the cable is connected correctly and firmly.
Check if the power of any external equipment is ON.
Check if the input selection matches the connection terminal.
Check if the PC is in Power Save mode or not.
Invalid Scan Freq.
The unit receives unsupported signals.
Check if the cable is connected correctly and firmly.
Check if the input signal is compatible with the specification of the monitor.
Not Available
This shows when the selected operation is not available.
Auto Adjusting
This indicates that it is in the process of auto adjusting. (in RGB mode)
Page
32
14
~
16
32
36 , 38
29
Symptom and Checklist
Symptoms
Checklist
No picture - no sound
Check the Indicating lamp status (Off, Red, Green, or Orange).
Check the connection of the power cord and/or other cables.
Check if the power of the unit or external equipment is ON.
Check if the correct mode is selected.
Check if the unit is in “Standby mode” or “Power Save mode”.
Adjust the values in “Picture” menu and “Audio” menu.
Multiple images-normal sound
Check the connections to external equipment.
Intermittent interference
Check if the source of interference is shielded correctly.
Move these kinds of electrical devices away from the unit.
Page
14
~
18
20 , 32
14
~
16
Check the volume level.
Normal picture, but no sound
Check if the
button has been pressed or not.
Check the connections to external equipment.
Connect to PC (RGB)/DVI Analogue Audio Input terminal if
the input signal screen display shows “DVI” by pressing the
19 , 20
button.
Check if “Speakers” in “Audio” menu is set to On.
No picture - normal sound
Check the value level of “Brightness” and “Contrast” in
“Picture” menu.
Check the connections to external equipment.
Check the setting of “RGB Input” in “Setup” menu in RGB
or Composite input.
The remote control does not work.
Check if the batteries are installed correctly.
The batteries might be exhausted. Replace them with new
ones.
Remove all obstructions from in front of the sensor window
on the unit.
Check if the buttons on the control panel are working.
The buttons both on the remote
control and control panel do not
work.
33
Unplug and Connect the power cord again.
Hold down the Reset button on the control panel for over a
second.
14
~
16
23
27
~
29
12 , 13
11
TROUBLESHOOTING (continued)
Symptoms
Checklist
ENGLISH
Symptom and Checklist (continued)
Page
14
~
16 ,
No colour-normal sound
Check the connections to external equipment.
Check “Colour System” in Composite input.
No picture
The Indicating lamp ĺ Off
Check if the power cord is plugged into the socket securely.
Check if the power switch on the unit is on.
No picture
The Indicating lamp ĺ Orange
It means that the unit is in “Power Save
mode”.
Check if all the cables to external equipment are connected correctly
and securely.
Check if the power to the external equipment is ON.
Check if the HDMI mode has been selected correctly.
Check if the PC is in Power Save mode or not.
Refer to “Power Save Mode” and “When the Following Messages
Appears on the Screen”.
No picture
The indicating lamp ĺ Green
Check if the signal cable is connected correctly and securely.
Adjust the level of “Brightness” and “Contrast” lower.
The top of the unit and surface of the
panel heat up.
This may occur if you use the unit for a long time. Unplug the power cord
for a while. Please note that this is not a malfunction.
36 , 38
Some screen display sizes cannot be
switched in.
button on the remote
Check the signal status by pressing the
control. The available screen display size is different depending on the
current signal status.
30 , 31
Image cannot be displayed from HDMI
input.
Check if the cables are connected correctly.
Check the output format of the equipment.
(Please refer to “CONNECTION” and “Recommended Signal List”.)
The image and audio are mismatched
when in RGB or HDMI-DVI mode.
Check if the PC (RGB)/DVI Analogue Audio Input terminal is connected
to the same external device.
27
17 , 18
32
14
~
16
20 ,
14 ,
36
~
38
14 , 16
34
TROUBLESHOOTING (continued)
Symptom and Checklist (continued)
Symptoms
Checklist
The image on the screen is moving in
an oblique direction.
(RGB input mode only)
Adjust “Horizontal Clock” and “Clock Phase”.
29
The coarse horizontal stripes can be
seen in full-display mode.
(RGB input mode only)
Adjust “Horizontal Clock”.
29
Part of the image is missing.
(RGB input mode only)
AAAAA
The horizontal stripes are moving
vertically with flickering screen.
(RGB input mode only)
When the characters are displayed
on the whole screen, the vertical
stripes appear and some of the
characters are blurred.
(RGB input mode only)
Try “Auto Adjust” or press the
button on the remote
control.
Check if the input signal is compatible with the signals on
“Recommended Signal List”.
Check if “WXGA Mode” is set correctly.
29 , 38
Check the signal status of the PC by pressing the
button on the remote control.
Try “Auto Adjust” or press the
button on the remote
control.
If the display condition is not improved with “Auto Adjust”,
adjust “Horizontal Clock”.
29
Try “Auto Adjust” or press the
button on the remote
control.
If the condition is not improved with “Auto Adjust”, adjust
“Clock Phase” until you get the clearest image.
29
When small patterns are displayed
on the screen, the entire screen is
flickering.
(RGB input mode only)
Try “Auto Adjust” or press the
button on the remote
control.
If the condition is not improved with “Auto Adjust”, adjust
“Clock Phase” until you get a flicker-free display.
29
Image cannot be displayed in the
correct position.
(RGB input mode only)
Press the
button to check if the input signal of
the displayed image is compatible with the specification of the
unit.
When the letter string is displayed in
full-screen, all of the characters on
the screen are blurred.
(RGB input mode only)
35
Page
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
20 , 36
38
PRODUCT SPECIFICATIONS
Display dimensions
Approx. 32 inches (698 (H) x 392 (V) mm, diagonal 801mm)
Resolution
1366 (H) x 768 (V) pixels
ENGLISH
SPECIFICATION
Panel
including Stand: 814 (W) x 587 (H) x 249 (D) mm
excluding Stand: 814 (W) x 538 (H) x 39* (D) mm
*thinnest part: 35mm
Net dimension
including Stand: 13.5kg
Net Weight
excluding Stand: 10.9kg
UT32MH70U/E
Temperature
Operating: 5ºC to 35ºC
Relative humidity
Operating: 20% to 80%
Ambient conditions
Power supply
AC220-240V, 50Hz
Power consumption/ at stand by
132W/<0.8W
Audio output
speaker 6W + 6W
Display dimensions
Approx. 37 inches (820 (H) x 461 (V) mm, diagonal 941mm)
Resolution
1920 (H) x 1080 (V) pixels
Panel
Net dimension
including Stand: 936 (W) x 657 (H) x 310 (D) mm
excluding Stand: 936 (W) x 607 (H) x 39* (D) mm
*thinnest part: 35mm
Net Weight
including Stand: 17.4kg
excluding Stand: 14.6kg
UT37MX70U/E
Temperature
Operating: 5ºC to 35ºC
Relative humidity
Operating: 20% to 80%
Ambient conditions
Power supply
AC220-240V, 50Hz
Power consumption/ at stand by
171W/<0.8W
Audio output
speaker 6W + 6W
Display dimensions
Approx. 42 inches (930 (H) x 523 (V) mm, diagonal 1067mm)
Resolution
1920 (H) x 1080 (V) pixels
Panel
Net dimension
including Stand: 1036 (W) x 728 (H) x 310 (D) mm
excluding Stand: 1036 (W) x 678 (H) x 39* (D) mm
*thinnest part: 35mm
Net Weight
including Stand: 20.9kg
excluding Stand: 18.0kg
UT42MX70U/E
Temperature
Operating: 5ºC to 35ºC
Relative humidity
Operating: 20% to 80%
Ambient conditions
Power supply
AC220-240V, 50Hz
Power consumption/ at stand by
234W/<0.8W
Audio output
speaker 6W + 6W
(HDMI input)
Input terminals
HDMI: HDMI input terminal
Audio input terminal (Mini-pin)*
Input signals
HDMI: VGA/60, 480i, 576i, 480p, 576p, 720p/50, 720p/60, 1080i/50, 1080i/60,
1080p/50, 1080p/60, 1080p/24
(RGB/Composite input)
Input terminals
Analogue RGB input terminal (D-sub 15 pin)
Audio input terminal (Mini-pin)*
Input signals
0.7 Vp-p, analogue RGB (Recommended Signal)
Composite video: PAL, SECAM, NTSC3.58, NTSC4.43, PAL60, PAL-M, PAL-N
Sync signals
H/V separate, TTL level [2KŸ]
The unit takes at least 30 minutes to attain the status of optimal picture quality.
* This Analogue Audio Input terminal can be used for PC (RGB) or HDMI-DVI.
36
PRODUCT SPECIFICATIONS (continued)
Signal Input
RGB terminal (D-sub 15 pin connector)
Pin
Input signal
1
R
2
G/Composite
3
B
4
No connection
5
No connection
6
R.GND
7
G.GND/Composite.GND
8
B.GND
9
+5V
10
GND
11
No connection
12
[SDA]
13
H.sync
14
V.sync.
15
[SCL]
HDMI connector pin specifications
37
Pin
Input signal
Pin
Input signal
1
TMDS Data2+
11
TMDS Clock Shield
2
TMDS Data2 Shield
12
TMDS Clock-
3
TMDS Data2-
13
CEC
4
TMDS Data1+
14
Reserved(N.C. on device)
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
DDC/CEC Ground
7
TMDS Data0+
17
8
TMDS Data0 Shield
18
+5V Power
9
TMDS Data0-
19
Hot Plug Detect
10
TMDS Clock+
PRODUCT SPECIFICATIONS (continued)
ENGLISH
Recommended Signal List
With HDMI input
Signal mode
No.
Signal
Name
Resolution
Vertical
frequency (Hz)
Horizontal
frequency
(kHz)
Dot clock
frequency
(MHz)
1
2
3
4
5
6
7
8
9
10
11
12
VGA
576i
480i
576p
480p
1080i/50
1080i/60
720p/50
720p/60
1080p/50
1080p/60
1080p/24
640 X 480
720(1440) X 576
720(1440) X 480
720 X 576
720 X 480
1920 X 1080
1920 X 1080
1280 X 720
1280 X 720
1920 X 1080
1920 X 1080
1920 X 1080
59.94
50.00
59.94
50.00
59.94
50.00
60.00
50.00
60.00
50.00
60.00
24.00
31.47
15.63
15.73
31.25
31.47
28.13
33.75
37.50
45.00
56.25
67.50
27.00
25.18
27.00
27.00
27.00
27.00
74.25
74.25
74.25
74.25
148.50
148.50
74.25
Remarks
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
CEA-861D
With RGB input
Timing Name
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Sync
Polarity
(H/V)
Remarks
640 x 400 @ 70Hz
640 x 480 @ 60Hz
800 x 600 @ 60Hz
1024 x 768 @ 60Hz
1280 x 768 @ 60Hz
1280 x 1024 @ 60Hz
1360 x 768 @ 60Hz
31.469
31.469
37.879
48.363
47.776
63.981
47.712
70.086
59.940
60.317
60.004
59.870
60.020
60.015
25.175
25.175
40.000
65.000
79.500
108.000
85.500
-/+
-/+/+
-/-/+
+/+
+/+
VGA
VGA
VESA
VESA
VESA / WXGA Mode: 1280 x 768
VESA
VESA / WXGA Mode: 1360 x 768
The type of video board or the connecting cable used may not allow for correct displays adjustment of Horizontal
Position, Vertical Position, Horizontal Clock and Clock Phase.
The unit differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and
vertical sync signal polarities. Note that different signals having all these elements alike may be handled as the
same signal.
For UT32MH70U/E model, the image with 1280 x 1024 @ 60Hz is degraded vertically.
38
Thank you for purchasing this Hitachi LCD Monitor.
In the unlikely event that this product should develop a fault, we undertake to
repair or replace any part of the product which fails due to a manufacturing
defect within 12 months of the date of purchase provided that ...
1. the product has been installed and used only in accordance with the
instructions supplied with the product.
2. the product has not been repaired, maintained, or modified by any person
other than a Hitachi authorized dealer.
3. the product serial number has not been removed or altered.
•This guarantee does not apply to a product acquired second hand or for
commercial or communal use.
•This guarantee does not cover the replacement of exhausted batteries or the
adjustment of user controls.
•Any parts replaced under this guarantee shall become the property of
Hitachi Europe Ltd.
•Please note that evidence of the date of purchase will be required before any
service under this guarantee is carried out.
Use the boxes provided below to record your LCD Monitor’s Model and Serial Number these are found on the rating plate located on the rear of the LCD Monitor. Also, record
where and when you purchased this LCD Monitor. This information will help any future
queries you may have and should be used in all correspondence with Hitachi service centres.
MODEL
SERIAL NUMBER
DEALER/STORE
DATE
PURCHASED
This guarantee does not affect your statutory rights.
In all cases of difficulty,
please consult your Hitachi dealer.
39
Hitachi Ltd.
Consumer Business Group
Shin-Otemachi Bldg 5f, 2-1, Otemachi 2-Chome,
Chiyoda-Ku, Tokyo 100-0004 Japan
HITACHI EUROPE LTD.
Consumer Affairs Department
PO Box 3007
Maidenhead
Berkshire SL6 8ZE
UNITED KINGDOM
Te l : 0870 405 4405
Email: [email protected]
HITACHI EUROPE S.A.
364, Kifissias Ave. & 1, Delfon Str.
152 33 Chalandri
Athens
GREECE
Te l : 210 6837200
Fax: 210 6835694
Email: [email protected]
HITACHI EUROPE GmbH
Munich Office
Dornacher Strasse 3
D-85622 Feldkirchen bei München
GERMANY
Te l : 089-991 80-0
Fax: 089-991 80-224
Hotline: 0180-551 25 51 (12ct/min.)
Email: [email protected]
HITACHI EUROPE S.A.
Gran Via Carles III, 86 Planta 5a
Edificios Trade - Torre Este
08028 Barcelona
SPAIN
Te l : 93 409 2550
Fax: 93 491 3513
Email: [email protected]
HITACHI EUROPE S.r.l.
Via T. Gulli n.39
20147 MILAN
ITALY
Te l : 02 487861
Fax: 02 48786381
Servizio Clienti
Te l . 02 38073415
Email: [email protected]
HITACHI EUROPE S.A.S
Lyon Office
Digital Media Group
94 Quai Charles de Gaulles, 69006 Lyon
FRANCE
Te l : 04 72 14 29 70
Fax: 04 72 14 29 99
Email: [email protected]
HITACHI EUROPE LTD.
Benelux Branche Office
Bergensesteenweg 421
1600 Sint-Pieters-Leeuw
BELGIUM
Tel : 0032/2 363 99 01
Fax: 0032/2 363 99 00
Email : [email protected]
HITACHI EUROPE LTD.
Kodaňská 46
101 00 Praha 10
CZECH REPUBLIC
Tel
: 234 064 512
Fax: 234 064 213
Email : [email protected]
HITACHI EUROPE AB
Box 77
S-164 94 KISTA
SWEDEN
Te l : 08 562 711 00
Fax: 08 562 711 11
Email: [email protected]
HITACHI EUROPE AB
(Norway Branch Nuf)
Strandveien 18
1366 Lysaker
NORWAY
Te l : 67519030
Fax: 67519032
Email [email protected]
HITACHI EUROPE AB
Egebækvej 98
2850 Nærum
DENMARK
Te l : 43 43 60 50
Fax: 43 43 60 51
Email [email protected]
HITACHI EUROPE AB
Lars Sonckin kaari 16
FIN-02600 ESPOO
FINLAND
Te l : 010-8503085
Fax: 010-8503086
Email [email protected]
www.hitachidigitalmedia.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement