Star Micronics NX 1500 printer User's Manual

PDF

Dokument

Reklama

MULTI-FONT

NX-1500

Federal Communications Commission

Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. This limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular instalIation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or reloate the receiving antenna.

- Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radiofI’V technician for help.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

The

above stafements apply only IO prin!ers marketed in the U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class B limits for radionoise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le present appareil numerique n’6men pas de bruits radi&lecttiques depassant les limites applicables aux appareils numeriques de la classe B prescrites dans le Rkglement sur le brouillage radio&crrique

CdictC par le minisere des Communications du Canada.

The above statement applies only lo printers markeled in

Canada.

Trademark Acknowlidgements

NX-1500, ND-lo&S, NR-10115: Star Micronics Co., Ltd.

IBM PC, PC-AT, PC-XT, Proprinter XL, Proprinter II, PC-DOS: International Business Machines

Corp.

Microsoft BASIC, MS-DOS: Microsoft Co oration

FX-1050, EX-1000, FX86e, FX286e: Seiko T pson Corp.

WordStar:

MicroPro International Corporation

NOTICE

STAR’s express permission is forbidden.

The contents of this manual are subject to change without notice. l l

Ail efforts have been made to ensure. the accuracy of the contents of this manual at the time of press. However, should any errors be detected, STAR would greatly appreciate being informed of them.

The above not with standing, STAR can assume no responsibility for any errors in this manual.

HOW TO USE THIS MANUAL

This manual is organized into nine chapters. To learn how to make the best use of your printer you are urged to read through chapters 1 through 3. The remaining chapters may be treated as a reference guide for programming operations, etc. It assumes a degree of acknowledge off the operation of computers (for instance, it assumes you know about hexadecimal numbers).

The chapters are as follows:

Chapter 1 - Setting up the printer

This chapter explains how to get the printer unpacked and set up. Read this chapter before you do anything else.

Chapter 2 - Control panel operations

There are a number of controls on the front panel which perform various functions related to paper handling, print modes and font selection.

After getting set up, read this chapter and try out the procedures in it to find out how the printer works.

Chapter 3 - DIP switch settings

This chapter explains how to set the DIP switches to make system settings on the printer.

Chapter 4 - Printer control commands

This chapter explains the different emulations provided by your printer, and the software commands used to drive it. This section is of use if you are writing or modifying programs to take advantage of the printer’s features.

Chapter 5 - Download characters

This chapter explains the procedures to create your own characters.

Chapter 6 - MS-DOS and your printer

Since the PC or PC-AT family of computers running under MS-DOS is currently the most popular configuration of microcomputer, we have included a few hints and tips to help you use your printer with such systems.

Since virtually all PCs are sold with a Microsoft BASIC interpreter, we have also included some hints, and a sample program in this language to demonstrate the capabilities of the printer.

Chapter 7 - Troubleshooting and maintenance

This section gives a checklist of points to check if your printer is not working in the expected way. It also includes details of some routine maintenance operations you can carry out yourself. It is not, however, a complete service manual. Call a qualified service engineer if you are unsure of your ability to carry out any maintenance or servicing operations.

Chapter 8 - Specifications

This section gives the specifications of your printer.

Chapter 9 - Character sets

These charts give the different character sets available, and the differences between national character sets (as set up with the DIP switches).

FEATURES OF THE PRINTER

This printer is aconvenient, monochrome printerwithout frills but with a full complement of features, making it an excellent partner for a personal computer. It supports the IBM/Epson printer commands and character sets, enabling it to print just about anything your computer can generate, both text and graphics. Some of its main features are the following: l

Extensive software support

Since it is compatible with the Epson and IBM printers, it works with any software that supports those printers. That includes most word-processing and graphics programs, spread-sheets, and integrated software packages. l

Easy operation

Clearly understandable indicator displays and beep tones provide immediate feedback when you press the buttons on the control panel. The five buttons can operate in combinations to perform a surprising variety of functions, including micro-alignment. l

Easy care and maintenance

The ribbon cartridge can be replaced in seconds the print head in a few minutes. l

Versatile paper handling

Single sheets, fanfold forms, and multi-copy forms (up to triple-ply) are all accepted, and you can use either tractor or friction feed. A special feature enables you to keep fanfold forms parked in readiness while printing on other paper. l

Large variety of type styles and sizes

The printer has one draft style and four NLQ styles (Courier, Sanserif, and

Orator with small capitals or lower case), plus italics for all styles, plus condensed print, bold print, double-sized print, quadruple-sized print.

Locating the Printer .......................................................................... 1

Unpacking and Inspection ................................................................ 2

Check the carton contents ........................................................ 2

Parts name of the printer .......................................................... 3

Setting Up ........................................................................................ .4

Mount the platen knob ............................................................. 4

Install the ribbon cartridge ....................................................... 5

Connection ...............................................................................

Loading Single Sheets ...................................................................... 8

Automatic loading .................................................................... 8

Manual loading ...................................................................... 10

Loading and Parking Fanfold Forms

.............................................. 11

Loading the paper from the rear of the printer.. ..................... 11

Loading the paper from the bottom of the printer.. ............... .13

Paper parking ......................................................................... 15

Paper unparking ..................................................................... 15

Adjusting the Printing Gap ............................................................. 16

Buttons and Indicators ................................................................... .17

ON LINE button .................................................................... 18

PAPER FEED button ............................................................. 19

SET/EJECT PARK button ..................................................... 19

PRINT PITCH button ........................................................... .19

NLQ TYPE STYLE button .................................................... 20

Power-Up Functions ....................................................................... 21

Short test mode ..................................................................... .21

Long test mode ...................................................................... .22

Print area test mode ................................................................ 22

Stay in panel pitch ................................................................. .22

Stay in panel style .................................................................. 23

Stay in panel pitch and style .................................................. 23

Hexadecimal dump ................................................................ 23

Switch Combination Functions ..................................................... .26

Form feed ............................................................................... 26

Top of form ............................................................................ 27

Forward micro-feed .............................................................. .27

Reverse micro-feed ............................................................... .27

Clearing the buffer ................................................................. 28

r

Chapter 3 DIP SWITCH SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Location of the DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Functions of the DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 4 PRINTER CONTROL COMMANDS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Font Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Character Set Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Character Size and Pitch Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Vertical Position Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Horizontal Position Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Graphics Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Download Character Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Macro Instruction Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Other Printer Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Chapter 5 DOWNLOAD CHARACTERS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Designing Your Own Draft Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Defining the attribute data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Assigning the character data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Sample program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Defining Your Own NLQ Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Chapter 6 MS-DOS AND YOUR PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Installing Application Software with Your Printer . . . . . . . . . . . . . . . . . . . . . . . . 77

Embedding Printer Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Programming the Printer with DOS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Programming with BASIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..~. 82

How the program works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Modifications for IBM mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Chapter 7 TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . 89

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Paper feeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Replacing the Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Replacing the Print Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Chapter 8 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Chapter 9 CHARACTER SETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

103

Standard Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

IBM Character Set #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

IBM Character Set #l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

IBM Special Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

International Character Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

111

COMMAND SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

114

Chapter I

Subjects covered in Chapter 1 include -

Locating the printer l

Unpacking and inspection (names of parts) l

Setting up and connection l

Loading single sheets l

Loading and parking fanfold forms l

Adjusting the printing gap

LOCATING THE PRINTER

Before you start unpacking and setting up your printer, make sure that you have a suitable place on which to locate it. By “a suitable place”, we mean: l

A firm, level surface which is fairly vibration-free l

Away from excessive heat (such as direct sunlight, heaters, etc) l

Away from excessive humidity l

Away from excessive dust l

Supply it “clean” electricity. Don’t connect it to the same circuit as a large, noise-producing appliance such as a refrigerator. l

Make sure the line voltage is within 10% of the voltage specified on the identification plate. l

A location with sufficient space to locate the printer and any paper to be fed into it, as well as the printed paper coming out. l

If you are using a parallel connection to your computer, make sure that it is within 2m (6ft) of the printer (an RS-232 connection using the optional

RS-232 interface can be made over longer distances).

UNPACKING AND INSPECTION

Check the carton contents

Now unpack the contents of the printer shipping carton, and check each item in the box against Figure l- 1 to make sure that you have everything (there should be five items).

If any of these items are missing, contact your supplier.

Figwe 7-7. Check to make sure you have all five items: 1) Printer, 2) Paper guide, 3) Platen knob, 4) Ribbon cartridge, and 5) User’s manual.

The optional accessories which you may have ordered with your printer are: l

Serial (RS-232) interface board l

Automatic sheet feeder l

Pull tractor unit

Parts name of the printer

Make an external inspection of the printer. Note the locations of the following parts:

Entry slot

Rear mver lever

Power

Connector

Figure 1-Z. The printer’s external parts

Bail lever:

Release lever

Top cover:

Rear cover:

opens and closes the paper bail which holds the paper against the platen. releases the platen. This lever must be down for printing on single sheets, and up for fanfold forms. protects the print head and other parts. protects the sprocket feed mechanism.

Entry slot:

for inserting single sheets of paper.

Control panel: controls various printer functions.

Power switch: switches power on and off.

Connector:

for connecting the computer to the printer.

SETTING UP

Place the printer in the position where it is going to be permanently sited, and remove all packing material from inside the top cover. This packing material is intended to prevent damage to the printer in transit. You may like to keep this packing with the printer carton if you intend transporting the printer for use at a different location.

Mount the platen knob

The platen knob is packed into a recess of the white foam packing material which held your printer inside the printer carton. Be careful to remove the knob before disposing of the packing.

Mount the platen knob on the shaft on the right-hand side of the printer. Turn the knob on the shaft before pushing the knob fully into position.

Platen knob

Figure 1-3. Mounting the platen knob

Install the ribbon cartridge

Remove the top cover by lifting the front (using the two grips at the side), and pulling towards you. Now install the ribbon.

I 4

1. Use the tensioning knob on the ribbon cartridge to tighten the ribbon if it is slack (turn clockwise).

2. Use the grips on the side of the ribbon cartridge to help locate the cartridge (squeeze them inwards gently), and make sure that the spindles on the cartridge holder fit into the sockets on the cartridge itself.

Figure

1-5. Installing the ribbon cartridge

3. The ribbon should pass between the print head and the print head shield

(see Figure l-6).

Figure 7-6. Pass the ribbon between the print head and print head shield

Now, hold the top cover upright and engage the tabs at the back. Then swing the front edge down until the cover is closed.

Leave the top cover closed during normal operation. It keeps out dust and dirt and reduces the printer’s operating sounds. Open the cover only to change the ribbon or make an adjustment.

Connection

Connect the printer to your computer, using a standard parallel-type cable.

On a PC or PC/AT-type computer, this means that you use the 25way D- type connector at the computer end, and the Amphenol-type 36-way connector at the printer end. The pinouts of the printer’s connector are given in Chapter 8 if you need a cable for connection to another computer.

Plug the printer into a suitable mains outlet. However, DO NOT turn on the power switch at the front of the printer yet.

Figure 1-7. Connecting the interface cable

If you want to use the optional serial interface, slide out the parallel interface board by gripping the flips on both sides. Then insert the optional serial interface board all the way, as shown in Figure l-8.

Figure 1-8. Replacing the interface board

LOADING SINGLE SHEETS

This section will take you through the procedures for loading single sheets of paper.

If you are using the optional automatic sheet feeder (ASF), read the ASF instruction booklet.

Automatic loading

Single sheets can be loaded manually with power off, or automatically with power on. We will start the easy way with automatic loading.

1. Place the paper guide in position, locating the lugs on the bottom of the assembly into the slots on the rear cover of the printer.

Fjgure 1-9. Mounting the paper guide for single sheets

2. Make sure that the release lever is down. button to park the paper, then move the release lever downwards.

3. Adjust the paper guides to match the size of paper you will be using (re- membering that printing will start some distance from the left-hand edge of the carriage).

4. Place a single sheet between the guides, placing the side on which you want to print towards the back of the printer. Gently push the paper down in the guides until you feel it stop.

Figure l-10. Loading a single sheet

5. Turn on the power using the switch at the front of the printer. The printer will beep, indicating that no paper is in position for printing. The orange

POWER indicator also flashes to show this.

6. Now press the ( s~&$~#F ) button. The paper bail will move clear of the paper, and the paper will be fed and adjusted past the print head to a position ready for printing. The paper bail will be moved back to grip the paper against the platen, and the print head will move to the start position.

Manual loading

It is also possible to load paper manually while the printer’s power is off. The procedure is:

1. Place the paper guide in position, locating the lugs on the bottom of the assembly into the slots on the rear cover of the printer.

2. Check that printer power is off and the release lever at the back of the printer is down.

3. Open the top cover, then move the bail lever on top of the printer forward to open the paper bail.

4. Adjust the paper guides to match the size of paper you will be using (re- membering that printing will start some distance from the left-hand edge -- of the carriage).

5. Place a single sheet between the guides, placing the side on which you want to print towards the back of the printer. Gently push the paper down in the guides until you feel it stop.

6. Turn the platen knob clockwise until the front edge of the paper comes out from under the top cover.

7. If the paper is not straight, move the release lever to me up position, straighten the paper by hand, then move the release lever back down.

8. Move the bail lever back to close the paper bail.

LOADING AND PARKING FANFOLD FORMS

Fanfold forms have holes along the sides and perforations between the sheets. They are also called sprocket forms, punched forms, or

just

plain

“computer paper”. This printer accepts forms up to 16” wide. Fanfold forms are loaded, parked, and unparked as explained next.

Loading the paper from the rear of the printer

You can load the fanfold paper either from the rear or from the bottom of the printer. If you are going to load the paper from the bottom read the next section.

1. Place a stack of fanfold paper behind and at least one page-length below the printer.

2. Turn the printer’s power OFF.

3. Push the release lever to the upward position. This has the effect of releasing the paper from the platen roller, and engaging the tractor,feed.

4. Remove the paper guide and put it aside for the moment.

5. Remove the rear cover. Grip it by its rear edge and lift upwards and backwards as in Figure 1- 11. q

Figure l-11. Opening the rear cover

6. With the sprocket covers open, thread the paper over the sprockets, aligning holes with the pins on the sprockets.

7. Adjust the spacing of the sprockets by sliding them along the bar, using the clamp lever at the back of each sprocket to release and lock the sprocket in positin (when the lever is down, the sprocket may be moved, and when it is up, the sprocket is locked).

Sprocket cover

Clamp lever

Figure I-12. Thread the fanfold paper over the sprockets.

8. Now close the sprocket covers, again making sure that the paper sprocket holes are aligned with the pins on the sprockets. If they are not aligned properly, you will have problems with paper feeding, possibly resulting in tearing and jamming of the paper.

9. Turn on the printer using the switch at the front of the printer. The printer will beep (indicating that the paper is not yet fully loaded). This is also confirmed by the orange

POWER indicator flashing. the paper, and the paper will be fed and adjusted past the print head to a position ready for printing. The paper bail will be moved back to grip the paper against the platen, and the print head will move to the start position.

11. Remount the rear cover. Hold it tilted upward and insert the four tabs at the front into their slots. Then rotate the cover downwards, pressing down on the thumb pads on the left and right to snap it into place.

12. Mount the paper guide in the horizontal position shown in Figure 1 - 13, so that it will separate the printed from the unprinted paper.

Figure I-13. Mounting the paper guide for fanfold forms

Loading the paper from the bottom of the printer

You can load the fanfold paper from the bottom of the printer by using the optional pull tractor unit.

1. Remove the top cover, then move the bail lever on top of the printer forward to open the paper bail.

2. Mount the optional pull tractor unit onto the printer. Grip the lock levers on both side and push the unit downwards onto the platen roller shaft to fit the tractor grips, as shown in Figure 1-14.

3. Place a stack of fanfold paper below the printer.

4. With the sprocket covers open, thread the paper over the sprockets from the bottom of the printer, aligning holes with the pins on the sprockets.

5. Adjust the spacing of the sprockets by sliding them along the bar, using the clamp lever at the back of each sprocket to release and lock the sprocket in positin (when the lever is up, the sprocket may be moved, and when it is down, the sprocket is locked).

Platen roller shaft

Pull tractor unit

Figure I-14. Mounting the optional pull tractor unit

‘guru 1-75. Thread the fanfold paper over the sprodtets from the bottom of the printer.

6. Now close the sprocket covers, againmaking sure that the paper sprocket holes are aligned with the pins on the sprockets. If they are not aligned properly, you will have problems with paper feeding, possibly resulting in tearing and jamming of the paper.

7. Mount the new top cover.

Paper parking

After loading fanfold paper from the rear of the printer, you do not have to unload it when you want to print on a single sheet. The printer will “park” it for you if you follow the procedure below.

1. Paper parking starts with power ON, fanfold paper loaded in printing position, the release lever up.

2. Press the (

ON LINE

> button on the control panel to set the printer off- line

(ON LINE indicator off).

3. Tear off the printed form at the last perforation, leaving not more than about half a page showing above the top cover. If necessary, press the

(PAPER FEED)

button to feed paper forward until a perforation is located just above the top cover, and tear there.

4. Press the ( sE&~&FT )button on the control panel.

The printer will automatically feed the fanfold form backward until the paper is completely free of the platen.

5. Move the release lever to the down position.

6. Mount the paper guide in the upright position.

Now you can load single sheets either automatically or manually, as cx- plained previously. The fanfold paper remains parked at the back of the printer.

Paper unparking

When you want to resume using fanfold paper, the procedure is as follows.

1. Remove all single sheets from the printer.

2. Mount the paper guide in the horizontal position.

3. Move the release lever to the up position.

4. Press the ( s~&!&$F ) button. The printer will automatically feed the parked fanfold paper into position for printing.

ADJUSTING THE PRINTING GAP

The distance between the print head and the platen can be adjusted to accommodate different paper thicknesses. To make this adjustment, remove the top cover. The adjustment lever is located near the right end of the paper bail. Pulling the adjustment lever upwards narrows the gap; pushing it downwards widens the gap.

There are five positions; you can feel the lever clicking into each position.

The second position from the top is the one most commonly used for single sheets of paper. Try different positions until you get the best printing results. i-

Figure I-16. Adjusting for different thicknesses of paper

Chapter 2 CONTROL PANEL OPERATIONS

The control panel buttons can be pressed singly to perform the operations indicated by their names. Other functions can be obtained by holding these buttons down when you turn the printer’s power on. Still further functions can be executed by pressing the control panel buttons in combination.

This chapter explains all the button and indicator functions. l

Pause printing l

Feed paper (fast and slow, forward and reverse) l

Park fanfold forms l l

Set the top-of-form position

Select the print pitch l l

Select a font style

Print test patterns l

Prevent software from changing the panel pitch and font selections l

Print a hexadecimal dump l

Clear the printer’s buffer

BUTTONS AND INDICATORS

The printer is equipped with five buttons on the control panel: from right to left they are,(

ON LINE ],(PAPER FEED>

and( SEX&CT )(largerbuttons), and (PITCH) and (3VEJ (smaller buttons).

The following is a brief guide to the buttons and indicators on the control panel.

Figure 2-1. Control panel

ON LINE button

The (

ON LINE

) button sets the printer on-line and off-line. The state changes each time you press the button.

In the on-line state the printer receives data from the computer and prints the data. In the off-line state the printer stops printing and sends the computer a signal indicating that it cannot accept data.

The printer powers up in the on-line state if paper is present. If paper is not present, the printer powers up off-line with the

POWER indicator flashing.

When you load paper the

POWER indicator stops flashing, but the printer remains off-line. To start printing you must press the (

ON LINE

) button go on-line.

The three main times when you will want to press the(

ON LINE

)button are: l

Before and after any other panel operation

The other panel buttons operate only in the off-line state. First press the

( ON LINE

)button to go off-line, then perform the panel operation, then press the

( ON LINE

) button again to go back on-line. l

To pause during printing

If you press the

( ON LINE

) button during printing, the printer stops printing and goes off-line, allowing you to check the printout or change a control panel setting. Printing resumes when you press the

( ON LINE >

button again to go back on-line. l

To cut fanfold forms at the end of printing

When using fanfold forms, if you hold the

( ON LINE

)button down for one second, in addition to go off-line the printer feeds the paper about two inches forward, allowing you to cut it off just below the last line printed.

When you press the

( ON LINE

)button again to go back on-line, the paper feeds backward about one inch, stopping in the right place to resume printing.

I

PAPER FEED button

If you press this button in off-line, the paper feeds forward. If you hold this button down, the printer performs consecutive line feeds.

While you are feeding lines, if you

also

press the

(

ON LINE

> button, the paper will feed to the top of the next page. This is explained later.

SET/EJECT PARK button

Pressing this button causes the printer to execute paper loading if the paper has not loaded while in the off-line state.

If the paper has been loaded, this button causes the printer in different functions depending on the release lever position.

If the release lever is set to the upward position for the fanfold forms, this button operates to park the fanfold forms to the backward position.

If the release lever is set to the downward position for the single sheets, pressing this button ejects the paper.

This button has no effect if the optional pull tractor unit is mounted.

PRINT PITCH button

This button selects the print pitch that will be printed. Remember that the printer must be off-line for you to do this. Successive presses of this button will illuminate (and select) the following options in this order:

Pitch

Pica

Elite

Condensed pica

Condensed elite

Pica proportional

Elite proportional

Indicator(s)

PICA

ELITE

PICA, COND

ELITE, COND

PICA, PROP

ELITE, PROP

Holding down this button will cycle continuously between these options.

q

NLQ TYPE STYLE button

This button selects the font style to be printed. Draft style is always selected at power-up. To change to one of the NLQ (near letter quality) styles, set the beside the desired selection illuminate. The selections cycle in the following order:

Font style

Draft

Courier

Courier italic

Sanserif

Sanserif italic

Orator

Orator italic

Indicator(s)

(all indicators off)

COURIER

COURIER, ITALIC

SANSERIF

SANSERIF, ITALIC

ORATOR

ORATOR, ITALIC

-I

Holding down this button will cycle continuously between these options.

The Orator style is unique in two ways. First, it is a lot larger (higher) than the other styles. This makes it a good choice for labels and other text requiring high visibility. A little extra line spacing helps when Orator is used. Second, there are two versions of the Orator font style: one prints small capitals in place of lower-case letters; the other prints lower-case letters, but without descenders. The other font styles do not have a small-capitals option. Lower case always prints as lower case.

You get the small capitals when you select Orator from the control panel.

The font style can also be selected by printer commands given in Chapter 4.

Printer commands enable you to select both Orator styles, and also draft italic, which cannot be selected from the control panel.

POWER-UP FUNCTIONS

In addition to their normal functions, all the control panel buttons have special functions that operate if you hold them down while switching power on.

--F-A

Sray in p&d pitch

igure 2-2. Power-up functions of control panel

If the printer is turned on while the (

ON LINE

) button is pressed, the printer will enter the short self-test mode. The printer will start printing as soon as the (

ON LINE

) button is released, and will print the version number of the printer’s ROM, followed by six lines of the character set.

Each line will be offset by one character from the one before it. The final result will be something like the following.

Figure Z-3. Short self-test

Since the test print occupies the whole width of the carriage, it is recommended that the printer is loaded with continuous stationery to avoid possible damage to the print head and/or platen.

Long test mode

If the printer is turned on while the

(PAPER FEED)

button is pressed, the printer will enter the long self-test mode. The printer will start printing as soon as the

(PAPER FEED)

button is released, and will print the version number of the printer’s ROM, followed by the whole character set printed in each font styles and pitch available.

The test cycles endlessly. To stop the test you must switch power off.

Since the test print occupies the whole width of the carriage, it is recommended that the printer is loaded with continuous stationery to avoid possible damage to the print head and/orplaten. In addition, the total number of lines printed is considerable, more than can be accomodated on a single sheet, so fanfold paper is certainly suggested for this test.

Print area test mode

If you want to know how many lines on your paper can be printed, try to run up, the printer will enter the print area test mode. The printer will print the first line message, then prints the last line message on your single sheet after feeding the paper to the bottom of the paper.

If you have loaded the fanfold paper, the printer shows only the first line.

Stay in panel pitch

By holding the (PITCH) button down during power-up, you can prevent software interference with the print pitch selected from the control panel.

You will hear an acknowledging beep as power comes on.

After the beep tone, you can set the printer off-line, select a print pitch, then return to on-line and start printing. The pitch you selected will not be reset or otherwise changed by any commands your software may issue.

Stay in panel style

ference with the font style selected from the control panel. There will be an acknowledging beep, after which you can set the printer off-line, select a font style, then return to the on-line state and start printing. The selected font style will not be changed by any commands sent by software.

Stay in panel pitch and style

If you want to protect both the pitch and font style settings from software be a little long acknowledging beep.

Pressing these buttons during power-up does not prevent you from making any number of changes later from the control panel.

Hexadecimal dump

This feature is useful for programmers who are debugging printing programs and want to see the actual codes the printer is receiving. (Some computers change the codes the programmer intended.)

In this mode, all received data will be printed in a hexadecimal dump format, rather than the control codes being acted on as command codes.

This mode is accessed with the following procedure:

1. Holding

both the (PAPER FEED)

and ( sE?X&cT ) buttons down, turn power ON. A beep tone will be heard.

2. Start printing. In place of the usual printout you will get a formatted dump showing exactly what data the printer receives. Each line presents sixteen characters, their hexadecimal codes to the left and printable characters printed on the right.

3. At the end of the hexadecimal dump, set the printer off-line with the

(

ON LINE

Ibutton. This is necessary to print the last line.

The following BASIC program is a simple test you can run in hexadecimal mode:

10 FOR I=0 TO 255

20 LPRINT CHR$(I);

30 NEXT I

40 LPRINT

50 END

If your system passes the codes directly to the printer without changing them, you will get a printout like Figure 2-4.

00 01 02 QT 1:,4 e:,9 I:,6 0,

11 12 1: 14 15 16 17

21j :1 22 23 24 25 26 27

3,:) 51 32 33 34 75 36 :7

41.1 41 42 4: 44 45 46 47

50 51 52 53 54 55 56 57

60 61 62 6? 64 65 66 67

70 71 72 73 74 75 76 77

80 Et1 82

83 84 85 86 87

90 91 92 93 94 95 96 97

Ai> Al A2 A3 A4 A5 cl6 A7

HO Hl H2 B3 R4 H5 H.6 87

C2 Cz: C4 C5 C6 C7

DO Dl D2 D3 D4 D5 D6 07

El:,

E2 ET E4 E5 Eb E7

Fl F2 F3 F4 F5 Fb F7

OD OA

08 09 0.4 OB cc OD OE OF

16 19 1A 1B 1C 1D 1E 1F

28 29 ?A 2R 2C 2D 2E 2F

38 39 JA 3B 3C 3D 3E .JF

48 49 4A 4B 4C 4D 4E 4F

58 59 5A 5B 5C 5D 5E 5F

68 69 6A 6B 6C 6D 6E 6F

78 79 7A 78 7C 7D 7E 7F

88 89 8A 8P 8C ED 8E BF

98 99 9& 9H 9C 9D 9E 9F

638 A9 AA AH PC AD AE AF

R8 H9 BA BH BC BD BE BF

C8 C9 CA CH CC CD CE CF

DB D9 DA DB DC DD DE QF

E8 E9 EA EB EC ED EE EF

FB F9 FA FB FC FD FE FF

. . . . . . . . . . . . . . . .

‘“XB%b’ot+.-./

0123456789: ; <=.‘.‘?

B&BCDEFGHI JK.LM’qO

PQRSTUVWXYZC\1’-

.abcdefghlJklmno pqrstuvwxyz~~ I >‘.

................

. .

Figure 2-4. Sample hexadecimal dump

Most BASICS, however, are not quite that straightforward. For example, the

IBM-PC prints the following.

630 01 02 03 04 05 06 07

10 11 12 13 14 15 16

20 2 1 22 23 24 25 26 27

30 31 32 33 34 35 36 37

40 41 42 43 44 45 46 47

50 51 52 53 54 55 56 57

60 61 62 63 64 65 66 67

70 71 72 73 74 75 76 77

80 El 82 83 84 a5

86 87

90 91 92 93 94 95 96 97

AC1 Al A2 A3 A4 A5 Ah A7

BO Hl n2 H3 B4 85 B6 87

CO Cl C2 CT C4 C5 C6 C7

DO Di D2 D; D4 D5 D6 D7

E2 E: E4 ES E6 E7

FO Fl

OD OA

F2 F: F4 F5 F6 F7

08 09

OA OB DC OD OPI OE

17 1E 19 18 1C 1D 1E 1F

28 29 2A 28 2C 2D 2E 2F

38 39 3A 3B 3C 3D 3E 3F

48 49 4A 48 4C 4D 4E 4F

58 59 5A 55 SC

5D 5E 5F

68 69 6A 6R 6C 6D 6E

78 79 7@ 7B 7C 7D 7E 7F

88 89 86 ER 8C 8D BE 8F

9B 99 9A 98 9C 9D 9E 9F

W A9 AFI FIB AC AD AE AF

BE B9

HA RH I3C HD BE

C8 C9 CCI CB CC CD CE

DB D9 DA DB DC DD DE DF

EEI E9 EA EB EC ED EE EF

FB F9 FA FB FC FD FE FF

. . . . . . . . . . . . . . . .

! “#*%L’ () :+, -. /

01234567E9:;<=>?

BABCDEFWIIJKLMNO

PQRSTUVWXYZC\l*-

‘abcdefghi jklmna pqrstuvwxyzC I >*.

. . . . . . . . . . . . . . . .

. .

When the IBM-PC BASIC interpreter sends hex code OD (carriage return) it adds an extra hex OA (iine feed). Hex code 1A (end-of-file) also gets special treatment: the interpreter does not send it at all. This can cause problems that generate graphics or download character data, but there is a solution. Try changing line 20 in the preceding program and adding the coding shown below.

Coding for IBM-PC with monochrome display:

20 GOSUB 100

100 O=INP(&H379)

110 OUT &H378.1

120 RETURN

:IF 0<128 THEN 100

:OUT &H37A,5 :OUT GH37A.4

Coding for IBM-PC with color adapter:

20 GOSUB 100

100 O=INP(&H3BD)

110 OUT &H3BC,I

12 0 RETURN

: IF 0<128 THEN 100

:OUT &H3BE,5 :OUT LH3BE.4

SWITCH COMBINATION FUNCTIONS

Several additional functions can be obtained by pressing the control panel buttons in combinations.

-FF-A

Top of form

Clearing the buffer

If you are using single sheets, this operation ejects the current page. If you are using fanfold forms, it feeds to the top of the next page.

1. Press the (

ON LINE

) button to set the printer off-line.

2. Press the

(PAPER FEED)

button and hold it down. The printer will start performing successive line feeds.

3. Still holding the

(PAPER FEED)

button down, press the (

ON LINE )

button, then release both buttons. The printer will smoothly eject the current page.

Top of form

When you turn on printer power, the top-of-form position is automatically set to the current position. If this is not where you want the top of the page to be, you can change the top-of-form position as follows.

1. Press the (

ON LINE

> button to set the printer off-line.

2. Move the paper to the desired top-of-form position by pressing the

(PAPER FEED]

button, orbyperforming a forward or reverse micro-feed.

3. Press and hold the (

ON LINE

> button.

4. Press and hold the (PITCH) button.

5. Release both buttons at the same time. The printer will beep to indicate that the top-of-form position has been set.

Forward micro-feed

For line alignment, you can feed the paper forward in very small increments as follows:

1. Press the (

ON LINE

) button to set the printer off-line.

2. Press the (

ON LINE

) button again and hold it down.

3. Press the

(PAPER FEED)

button. The paper will start advancing in a series of small steps. When you want to stop, release both buttons.

Reverse micro-feed

You can also feed the paper in small increments in reverse, to return to a higher position on the same page.

Note:With fanfold forms, do not try to return to a previous page. The perforation may catch inside the printer.

Press the

( ON LINE

1 button to set the printer off-line.

2. Press the (

ON LINE

) button again and hold it down.

3. Press the ( s~&/A@~ )button. The paper will start moving backwards in a series of small steps. When you want to stop, release both buttons.

Clearing the buffer

When DIP switch 2-l is ON, the printer stores received data in a large memory buffer. This creates a problem when you want to abandon a printing job and restart: the printer may be holding much more data in its buffer than it has actually printed, and this unprinted data must be cleared out before restarting. Turning power off is one way to clear the buffer, but there is another way:

1. Halt the printing program on the computer. If printing stops immediately, the buffer is clear and the rest of this procedure is unnecessary. If printing does not stop, continue as follows:

2. Press the (

ON LINE

) button to set the printer off-line. Printing will now stop, but there may be data remaining in the buffer.

3. Press and hold the

( ON LINE

) button. down. In about three seconds you will hear a beep tone signaling that the buffer has been cleared.

5. Release these buttons, make any necessary control panel settings, then set the printer back on-line.

It is essential to halt the printing program on the computer before you go off- line. Otherwise, when you go back on-line the computer will start sending data again and the printer will continue printing, with missing data where the buffer was cleared.

Chapter 3 D/P SWITCH SETTINGS

The bank of DIP (Dual In-line Package) switches inside the printer is used for various functions.

This chapter explains where the DIP switches are located, and how to use them.

. .._

LOCATION OF THE DIP SWITCHES

When you remove the printer’s cover and look inside, you will see on the green board at the bottom of the printer two groups of small white switches marked DSWl and DSW2. These are the printer’s DIP switches. DSWl has eight switches, named l- 1 to l-8 from left to right. DS W2 has four switches named 2-l to 2-4.

Figure 3-7. DIP switches

For all switches, the ON position is towards the back of the printer and the

OFF position is towards the front. To set a DIP switch, use a ballpoint pen or other small implement to move the switch to the ON or OFF position.

The printer’s power should be off when you set the DIP switches. Settings made while power is on do not take effect until power is switched off, then on again, because the printer reads the DIP switches only at power-up.

FUNCTIONS OF THE DIP SWITCHES

The printer is delivered with all DIP switch set to the ON position. These are the standard settings. By changing the settings, you can alter various printer functions to match your requirements. The following questions will help you make the right settings.

2-2

2-3

2-4

International character set

Switch l-l:

Is the page length of your paper 11 inches or 12 inches?

Leave this switch ON if you will be using 1 l-inch forms. Move it to the OFF position if you will be using 12-inch forms.

Switch 1-2:

Do you want an automatic carriage return?

Leave this switch ON. The printer will automatically perform a carriage return by moving to the left margin at each line feed. Even if your software sends a separate carriage-return code, an extra carriage return does no harm because two consecutive carriage returns are the same as one. Very few programs require this switch to be OFF.

Switch 1-3: Which type of printing area format do you want to use for single sheets?

This printer can use two types of printing area format for single sheets. By putting the switch ON (“A type”), the top of the first line of printing will start to one inch from the top of the paper, and the printed area will end to print one inch from the bottom of the paper.

By putting the switch OFF (“B type”), the top of the first line of printing will start l/6 inch from the top of the paper, and the printed area will end l/3 inch from the bottom of the paper.

Switch 1-4: Are you going to use the automatic sheet feeder (ASF)?

To use the automatic sheet feeder, move this switch to the OFF position.

Otherwise leave it ON.

Switch 1-5: Do you want the printer to stop printing at the end of the paper, or to keep printing?

Leave this switch ON except when you need to print very close to the end of the paper. When this switch is OFF the printer ignores the paper-out detector and prints down to (and beyond) the bottom edge.

Switch 1-6: Do you want to use the printer in standard mode or IBMmode?

Select the mode compatible with your computer and software. In standard mode the printer operates like the Epson FX- 1050. In IBM mode it operates like the IBM Proprinter XL. The ON position selects standard mode. The

OFF position selects IBM mode.

Switch 1-7: The action of this switch depends on the mode chosen with switch 1-6.

If you selected standard mode, do you want italics or graphic char- actes?

Leave this switch ON to print italics in the standard character set. If you set this switch to the OFF position, in place of italics you will get the graphic characters, international characters, and mathematical symbols of IBM character set #2. See Chapter 9, character codes 128 to 254.

If you selected IBM mode, do you want IBM character set #l or #2?

ON selects character set #2, which is for computers with an E-bit interface

(the most common kind). OFF sclccts character set #l, for computers with a 7-bit interface.

Switch 1-8: Do you want an automatic line feed?

If you leave this switch at the ON position, a separate line-feed code is required to obtain a line feed.

If you move this switch to the OFF position, the printer performs both a carriage return and line feed each time it receives a carriage-return code.

Most computer systems send a line feed code, or both a carriage return and line feed, at the end of each line, so this switch should be left ON.

If you get double line spacing when you expect single spacing, or if lines overprint each other, try changing the setting of this switch.

Switch 2-1: Does your software download new characters to the printer?

To download characters this switch must be OFF. The printer then uses its

RAM memory for storing character patterns and provides only a one-line print buffer. If you leave this switch ON the printer uses its RAM memory as an input buffer, allowing the computer to send data faster than the printer prints.

Switches 2-2 to 2-4: Do you want an international character set?

International character sets differ in their assignment of 14 character codes.

See the character tables at the back of this manual. With the DIP switches you can select one of eight character sets as follows:

* Denmark/Norway when switch l-6 is OFF and switch l-7 is ON.

Chapter 4 PRINTER CONTROL COMMANDS

The printer has two emulation modes: Standard mode and IBM mode.

In standard mode, the printer emulates the functions of the Epson FX- 1050.

In IBM mode, the printer emulates the IBM Proprinter XL. Additional command codes are included as a superset of these emulations.

The emulation is changed by means of DIP switch 1-6. When ON, the printer will be in standard mode, and when OFF, the printer will be in IBM emulation mode (see Chapter 3). It is not possible to change the emulation mode by means of software control or the front control panel.

This chapter describes the printer’s control commands. Some commands are common to both the standard and IBMmodes. In the descriptions of the commands, all commands will be given by function. The name of each command is followed by a table like the one below:

Mode

ASCII

Both

<ESC> “x”

“1”

Decimal

27 120 49

27 120 1

Hexadecimal

1B 78 31

18 78 01

Mode:

Indicates the mode in which the command is rccog- nized.

Std. Standard mode (DIP switch l-6 on)

IBM IBM mode (DIP switch l-6 off)

Both Both standard and IBM modes

ASCII:

Indicates the ASCII coding of the command.

Control characters are enclosed in pointed brackets: For example, CO> means character code 0.

Gives the command in decimal character codes.

Decimal:

Hexadecimal: Gives the command in hexadecimal character codes.

Parameters for which values must be supplied are indicated by italic letters such as n.

Many commands have alternative forms. Some commands use <ESC>

(character code 27) in Standard mode and <FS> (character code 28) in IBM mode. Other commands have parameters that can be specified as either character codes or digit characters, like the parameter 1 in the sample command above.

FONT CONTROL COMMANDS

Select draft quality characters

Mode

Both

IBM

ASCII

‘L ( “ ‘SF’ “)”

<ESC> “x1’ “0”

<ES3 “I” “0”

Decimal Hexadecimal

“)” “y.

40 40 70 41 41 57 28 28 46 29 29 39

27 120 48 1B 78 30

27 120 0

1 27 73 40

12773 0

1B 78 00

1 1B 49 30

1 1B 49 00

Changes from near letter quality to draft quality. Ignored if the

(3TViT) button was pressed during power-up.

Select draft elite characters

Mode

IBM

ASCII

<ESC> “I” “1”

Decimal

27 73 49

27 73 1

Hexadecimal

1B 49 31

1B 49 01

Changes to draft quality characters with elite pitch (12 cpi). Ignored

Select NLQ characters

Mode

Both

ASCII

<ESC> “x” “1”

Decimal

27 120 49

27 120 1

Hexadecimal

1B 78 31

1B 78 01

Changes from draft quality to near letter quality. The initial NLQ type style is Courier unless a different style has been selected by a during power-up.

Select NLQ type style

Mode

Both

ASCII

<ESC> “k” n

Decimal

27 107 n

Hexadecimal

IB 6B n

Selects an NLQ type style according to the value of n. In draft mode, this command remains dormant and takes effect later when NLQ is selected by <ES0 “x” 1. Ignored if the (m) button was pressed during power-up. n Type style

0 Courier (initial value)

1 Sanserif

2 Orator with small capitals

3 Orator with lower case

Select Courier characters

Mode ASCII

Decimal Hexadecimal

Both "(" "(" 9"' ")" 'I)" "0" 40 40 70 41 41 48 28 28 46 29 29 30

<ESC> “I” “3”

27 73 51 1B 49 33

IBM

<ESC>

"I" <3>

<ESC> “I" "7"

<ESC>

"I" <7>

27 73 3

27 73 55

27 73 7

1B 49 03

1B 49 37

1B 49 07

pressed during power-up.

Select Sanserif characters

Mode ASCII Decimal

Hexadecimal

Both “(” “(” “F” “)” “)” “1”

40 40 70 41 41 49 28 28 46 29 29 31

IBM <ESC>

<ESC>

“I” “2”

"I" <2>

27 73 50

Mode

Both

ASCII

<ESC> “E”

Decimal

27 69

Hexadecimal

1B 45

Causes subsequent draft characters to be emphasized by adding extra thickness to vertical strokes.

Cancel emphasized printing

Mode

Both

ASCII

<ESC> “F”

Cancels emphasized printing.

Decimal

27 70

Double-s trike printing

Hexadecimal

1B 46

Mode

Both.

ASCII

“ .‘ 6‘ ‘6 “B” “)” “)” “1”

( (

<ESC> “G”

Decimal Hexadecimal

40 40 66 41 41 49 28 28 42 29 29 31

27 71 1B 47

Causes subsequent characters to be printed in double-strike mode with a slight vertical paper motion in between, causing a thickening of horizontal strokes.

For bold print, use of double-strike is recommended in NLQ mode, and combined use of emphasized and double-strike is rccom- mended in draft mode.

Double-strike cannot be used with superscripts or subscripts.

Cancel double-strike printing

Mode

Both

ASCII

L‘ 6‘

(

“B”

<ESC>

“H”

“)”

“0”

Cancels double-strike printing.

Decimal

Hexadecimal

40 40 66 41 41 48 28 28 42 29 29 30

27 72

Start underlining

Mode

Both

ASCII

6. ( <‘ “_.. “)”

<EfjC> “-” “1”

<ESC> “-”

<l>

Decimal Hexadecimal

“)” “1”

40 40 45 41 41 49 28 28 2~ 29 29 31

27 45 49

27 45 1

1B 2D 31

18 20 01

Causes subsequent characters to be underlined. IBM block graphics characters and spaces skipped by horizontal tabulation are not underlined.

Stop underlining

Mode

Both

ASCII

‘, ( L‘ ‘6

‘.-.. “)”

<ESC> “-” “0”

Stops underlining.

Start overlining

Decimal Hexadecimal

“)” “0”

40 40 45 41 41 48 28 28 2D 29 29 30

27 45 48

1B 2D 30

27 45 0

1B 2D 00

Mode

Both

ASCII

<ESC> “

“ “1”

<ESC>

” _“ <l>

Decimal

27 95 49

27 95 1

Hexadecimal

1B 5F 31

1B 5F 01

Causes subsequent characters to be overlined. Spaces skipped by horizontal tabulation are not overlined.

Stop 0 verlining

Mode

Both

ASCII

<ESC>

*‘_“

“0”

<ESC> “

“ <O>

Stops overlining.

Superscript

Decimal

27 95 48

27 95 0

Hexadecimal

1B 5F 30

1B 5F OO

Mode

ASCII

Both .

<ESC> “S” “0”

Decimal

27 83 48

27 83 0

Hexadecimal

1B 53 30

18 53 00

Causes subsequent characters to be printed as superscripts. Does not change the character pitch.

Subscript

Mode

Both

ASCII

<ESC>

“S” “1”

Decimal

27 83 49

27 83 1

Hexadecimal

1B 53 31

1B 53 01

Causes subsequent characters to be printed as subscripts. Does not change the character pitch.

Cancel superscript or subscript

Mode

Both

ASCII

<ESC> “7”

Selects character set #l .

Select character set #2

Mode

Both

ASCII

<ESC> “6”

Selects character set #2.

Decimal

27 54

Hexadecimal

1B 36

Select international character set

Mode

Std.

IBM

ASCII cESC> “R” n

<FS> “R”

Decimal

27 82 n

28 82 n

Hexadecimal

IB 52 n

1C 52 n

Selects an international character set according to the value of n. n Character set

0 U.S.A

1 France

2 Germany

3 England

4 Denmark I

5 Sweden

6 Italy n Character set

7 Spain I

8 Japan

9 Norway

10 Denmark II

11 Spain II

12 Latin America

13 Denmark/Norway

The first eight of these character sets (from U.S.A. to Spain I) can be selected as power-up defaults by DIP switches 2-2 to 2-4.

Enable printing of all character codes

Mode

IBM

ASCII

<ESC> ‘I” nl n2

Decimal

27 92 nl n2

Hexadecimal

IB 5C nl n2

Enables printing of all characters in the IBM character set, including those assigned to character codes which are normally considered control codes. This command remains in effect for the next nl + n2 x 256 characters, where nl and n2 are numbers between 0 and 255.

During this interval no control functions are executed. If a code with no assigned character is received, the printer prints a space.

Enable printing of all character codes on next character

IMode 1 ASCII

1 IBM 1 <ESC> ” * ”

1 Decimal

1 27 94

1 Hexadecimal

1 IB 5E

This command operates like <ES0 ‘Y’ except that it remains in effect for only one character.

Select slash zero

Mode

Both

ASCII

<ESC> “ a “ “1”

Decimal

27 126 49

27 126 1

Hexadecimal

1B 7E 31

1B 7E 01

Causes subsequent zero characters to be overprinted with a slash

@Il.

Select normal zero

Mode

Both

ASCII

<Sb

<ESC> <Sb

Decimal

27 15

Hexadecimal

In Standard mode, changes from pica to condensed pica (17 cpi) or from elite to condensed elite (20 cpi). In IBM mode, changes from either pica or elite to condensed (17 cpi). Ignored if the (PITCH) button was pressed during power-up.

Cancel condensed printing

Mode

Both

ASCII

<DC2>

Decimal

Hexadecimal

In Standard mode, changes from condensed pica to normal pica or from condensed elite to normal elite. In IBM mode, always changes to normal pica. Ignored if the (PITCH) button was pressed during power-up.

Expanded printing

Mode

Both

ASCII

<ESC> ‘TV” “1”

Decimal

27 87 49

27 87 1

Hexadecimal

1B 57 31

1B 57 01

Causes subsequent characters to be expanded to double width.

Cancel expanded printing

Mode

Both

ASCII

<ESC> “W” “0”

<ESC>

Both

IBM

ASCII cESC>

<ESC>

“p”

“1”

<l>

Decimal

27 112 49

27 112 1

27 80 1

Hexadecimal

1B 70 31

16 70 01

1B 50 01

Causes subsequent characters to be proportionally spaced. Ignored

Select fixed spacing

Mode

Both

ASCII

<ESC> “p” “0”

IBM 1 <ESC> “p” <O>

Decimal

27 112 48

27 112 0

12780 0

Hexadecimal

1B 70 30

1B 70 00

( 1B 50 00

Causes subsequent characters to be printed with fixed character spacing. Ignored if the@iTBT)button was pressed during power-up.

Select master print mode

Mode

Both

ASCII

<ESC> “!” n

Decimal

27 33

Hexadecimal

1B 21

Selects a combined print mode according to the value of n. The value of n is the sum of the values given below for the desired char- acteristics.

Examples: n = 1 gives elite; n = 9 (1 + 8) gives emphasized elite; n

= 137 (1 + 8 + 128) gives underlined emphasized elite.

Function

Underline

Italic [*l]

Expanded

Double strike

Emphasized

Condensed [ *2]

Proportional [ *2]

Elite [*2] n value

128

[*l] Ignored if the (STYLE)button was pressed during power-up.

[*2] Ignored if the (PITCH) button was pressed during power-up.

Increase character spacing

Mode

Std.

ASCII

<ESC> <SP> n

Decimal

27 32

Hexadecimal

1B 20

Increases the space between characters by n/240 inches, where n is a number from 0 to 127. Used in microjustification.

Select double or quadruple size

Mode

Both

ASCII

<ESC> “h” n

Decimal

27 104

Hexadecimal

1B 66

Selects the size of subsequent characters as shown below. Extra- high characters align along the cap-line of normal characters, with the base line temporarily moving down. Line spacing is temporarily doubled when n = 1,5 or 6 and quadrupled when n = 2. To print correctly when n = 3,4,5 or 6, set the line spacing to 24/216 (l/9)

of an inch with <ES0 “3” <24>, and print the same characters twice, upper half on one line, lower half on the next. For accurate alignment of the two halves, select unidirectional printing with

<ESC> “U” <l>. n Effect

0 Normal size

1 Double-high, double-wide

2 Quadruple-high, quadruple-wide

3 Double-high, double-wide (Lower half only)

4 Double-high, double-wide (Upper half only)

5 Quadruple-high, quadruple-wide (Lower half only)

6 Quadruple-high, quadruple-wide (Upper half only)

Select character size

Mode

ASCII

Both “(” “(” “S” “)” 6.)” n

Decimal

Hexadecimal

40 40 a3 41 41 n 28 28 53 29 29 n

Selects a combinationof characterheight and width according to the value of n, as below. Does not move the base line. n Character width

0 Single width

1 Double width

2 Single width

3 Double width

Character height

Single height

Double height

Double-height characters are always printed at near letter quality.

Double height printing temporarily cancels the super/subscript and condensed printing modes, but these modes resume when the printer returns to normal height.

Print double-height characters

Mode

Both

ASCII

<ESC> “w” “1”

Decimal

27 119 49

27 119 1

Hexadecimal

1B 77 31

1B 77 01

Prints subsequent characters at double height without moving the base line, and without changing the line spacing. Temporarily cancels super/subscript and condensed printing modes.

4.5

Return to normal height

Mode

Both

ASCII

<ESC> “w” “0”

<ESC> “w" <0>

Decimal

27 119 48

27 119 0

Hexadecimal

1B 77 30

1B 77 00

Terminates double-height printing and prints subsequent characters at normal height. Resumes super/subscript and condensed printing if these modes were in effect-before double height was selected.

Select character height, width, and line spacing

1 ASCII

CO> CO>

n m

1 Decimal

1 Hexadecimal 1

27 91 64 4 0 1B 58 40 04 00

Onm OOOOnm

Selects a combination of character height, width, and line spacing according to the value of n and m, as below. Does not move the base line.

- n

Line spacing Character height

- m

Unchanged

Single

Double

Unchanged

Single height

Double height

Unchanged

Single height

Double height

Unchanged

Single height

Double height

Character width r

Single width (same as cESC> “W” 0)

Double width (same as <ES0 “W” 1)

Double-height characters are always printed at near letter quality.

Double height printing temporarily cancels the super/subscript and condensed printing modes, but these modes resume when the printer returns to normal height.

‘-

VERTICAL POSITION COMMANDS

Set line spacing to l/8 inch

Mode

Both

ASCII

<ESC> “0”

Decimal

27 48

Hexadecimal

1B 30

Sets the distance the paper advances or reverses in subsequent line feeds to l/8 inch.

Set line spacing to 7172 inch

Mode

Both

ASCII

<ESC> “1”

Decimal

27 49

Hexadecimal

1B 31

Mode

IBM

ASCII

<ESC> “2”

Decimal

27 50

Hexadecimal

1B 32

Sets the line spacing to the value defined by the last preceding

<ESC> “A” command. Sets the line spacing to l/6 inch if there is no preceding <ES0 “A” command.

Line feed

Mode

ASCII

Both 1 <LF>

Decimal

I 10

Hexadecimal

1 OA

Prints the current line and feeds the paper to the next line. If DIP switch l-2 is ON, also moves the next print position to the left margin. See the preceding commands for the line spacing.

Reverse line feed

Mode

Both

ASCII

Decimal

27 10

Hexadecimal

1B OA

Prints the current line and feeds the paper in the reverse direction to the preceding line. If DIP switch l-2 is ON, also moves the next print position to the left margin. See the preceding commands for the line spacing. Ignored when friction feed is used.

Perform one w’2164nch line feed

Mode

Both

ASCII

<ESC>

“J-’ n

Decimal

27 74 n

Hexadecimal

1B 4A n

Feeds the paper once by n/2 16 inches, where n is between 1 and 255.

Does not move the print position right or left when DIP switch l-2 is OFF. Does not change the line-spacing setting.

Perform one n/2164nch reverse line feed

Mode

Both

ASCII

<ESC> “‘j”

Decimal

27 106 n

Hexadecimal

1B 6A n

Feeds the paper once by n/2 16 inches in the reverse direction, where

n is between 1 and 255. Does not move the print position right or left when DIP switch l-2 is OFF. Does not change the line-spacing setting.

Feed paper n lines

Mode

Both

ASCII

<ESC> “f’

“1” n

<ES&

“f’ <l> n

Decimal

27 102 49 n

27 102 1 n

Hexadecimal

1B 66 31 n

1B 66 01 n

Feeds the paper n lines from the current line, where

is between 0 and 127.

Set top of page at current position

Mode

Both

ASCII

<ESC> “0”

Decimal

27 79

Hexadecimal

IB 4F

Cancels both the top margin and the bottom margin.

Form feed

Mode

Both

ASCII

<FF>

Decimal

Hexadecimal

Feeds the paper to the top of the next page according to the current page length, and moves the print position to the left margin. When the automatic sheet feeder (ASF) is selected (DIP switch l-4 is

OFF), this command ejects the current page.

Return to top of current page

Mode

Both

ASCII

Decimal

27 12

Hexadecimal

IB OC

Feeds the paper backward to the top of the current page. Ignored when friction feed is used.

Disable paper-out detector

Mode

Both

ASCII

<ESC> “8”

Decimal

27 56

Hexadecimal

18 38

Causes the printer to disregard the signal sent by the paper-out detector, enabling printing to the bottom of the paper. Overrides the setting of DIP switch 1-5.

Enable paper-out detector

Mode

Both

ASCII

<ESC> “9”

Decimal

27 57

Hexadecimal

iB 39

Causes the printer to stop printing before the end of the paper.

Overrides the setting of DIP switch 1-5.

Set vertical tab stops

1 Decimal 1 Hexadecimal

Both 1 <ESC> “B” nl n2 . . . CO> 27 66 nl n2 . . . 0

1B 42

n2 .

Cancels all current vertical tab stops and sets new vertical tab stops at lines nl, n2, etc., where

nl,

n2, etc. are numbers between 1 and

255. A maximum of 16 vertical tab stops can be set. The tab stops must be specified in ascending order, any violation of ascending order terminates the tab stop list. Standard termination is by the <O> control code. The vertical tab stops are set in terms of the current line spacing and do not move if the line spacing is changed later.

Set vertical tab stops every

lines

Mode

Both

ASCII

<ESC> “e” “1”

<ESC> “e” -A> n

Decimal

27 101 49

27 101 1

n n

Hexadecimal

18 65 31

1B 65 01 n

Cancels all current vertical tab stops and sets new tab stops every

lines, where

is between 1 and 127.

Set vertical tab stops in channel

Mode

Both

ASCII

<ESC> “b” n0

n2 nl

. . . <o>

Decimal

27 98

n0 nl n2 . . . 0

Hexadecimal

1B 62 nO

F7.2 . . . 00

Cancels all current vertical tab stops in channel

n0,

(where

is between 0 and 7) and sets new vertical tab stops in this channel. (A channel is a set of vertical tab stops selected by the cESC> “/” command.) See <ESC> “B” for parameters

nl, n2, . . . -CO>.

Select vertical tab channel

Mode

Both

ASCII

<ESC> “f’ n0

Decimal

27 47

Hexadecimal

1B 2F n0

Selects a set of vertical tab stops designated by a channel number

(n0)

from 0 to 7. The tab stops in each channel are set by cESC> “b”.

Vertical tab

Mode

Both

ASCII

<VT>

Decimal

Hexadecimal

Feeds the paper to the next vertical tab stop and moves the print position to the left margin. Performs a line feed if no vertical tabs arc set, as at power-up. Feeds to the top of the next page if vertical tabs are set but the current line is at or below the last vertical tab stop.

HORIZONTAL POSITION COMMANDS

Set left margin

Mode

Both

ASCII

<ESC> “1”

Decimal

27 108 n

Hexadecimal

IB 6C n

Sets the left margin at column

(where

is between 0 and 255) in the current character pitch (pica pitch if proportional spacing is selected). The left margin does not move if the character pitch is changed later. The left margin must be at least two columns to the left of the right margin and within the limits below:

Pica

Elite

Condensed pica

Condensed elite

Expanded pica

Expanded elite

Expanded condensed pica

Expanded condensed elite

Olnl

132

0 5 n I 158

0 I n I 226

0 I n I 255

OInI66

O<n579

OInS

Olnl

112

132

Set right margin

Mode

Std.

IBM

ASCII

<ES6

<FS>

“Q” n

Decimal

27 01

28 81

n n

Hexadecimal

18 51

1C 51

n n

“Q” n

Sets the right margin at column

in the current character pitch (pica pitch if proportional spacing is currently selected). Column n becomes the last character position in the line. The right margin does not move if the character pitch is changed later. The right margin must be within the limits below:

Pica

Elite

Condensed pica

Condensed elite

Expanded pica

Expanded elite

Expanded condensed pica

Expanded condensed elite

I n I

136

5 In5163

7 I n I 233

8 5 n I 255

2In168

31n181

41n1116

41ns136

Set left and right margins

Mode

Both

ASCII

<ESC> “X” nl n2

Decimal

27 88

Hexadecimal

1B 58

Sets the left margin at column

and the right margin at column n2.

See the preceding commands for margin restrictions and other notes.

Mode

Both

ASCII

CBS>

Decimal

Hexadecimal

Moves the print position one column to the left. Ignored if the print position is at the left margin. This command can be used to overstrike or combine characters.

Left justify

Mode

Both

ASCII

<ESC> “a” “0”

Decimal

27 97 46

27 97 0

Hexadecimal

1B 61 30

1B 61 00

Aligns subsequent text with the left margin, leaving the right margin ragged.

Center text

IMode 1 ASCII

Both <ESC> “a” “1”

I Decimal

1 27 97 49

1 27 97 1

I Hexadecimal

1B 61 31

1 1B 61 01

Centers subsequent text between the left and right margins.

Right justify

Mode

Both

ASCII

<ESC> “a” “2”

Decimal

27 97 50

27 97 2

Hexadecimal

1B 61 32

1B 61 02

Aligns subsequent text with the right margin, leaving the left margin ragged.

Set horizontal tab stops

Mode ASCII

Both <ESC> “D” nl

n2 .

Decimal

-CO>

27 68

n? .

Hexadecimal nl n2

Cancels all current horizontal tab stops and sets new tab stops at columns

nl, n2,

etc. in the current character pitch (pica pitch if proportional spacing is currently selected), where nl,

n2,

etc. are numbers between 1 and 255. The maximum number of horizontal tab stops allowed is 32 in Standard mode and 28 in IBM mode. The tab stops must be specified in ascending order; any violation of ascending order terminates the tab stop list. Standard termination is by the <O> control code. To clear all tab stops, specify <ES0 “D” co>.

Set horizontal tab stop every

columns

Mode

Both

ASCII

<ESC> “e” “0” n

<ES6 “e” <O> n

Decimal

27 101 48

27 101 0

Hexadecimal

1B 65 30

1B 65 00

Cancels all current horizontal tab stops and sets new tab stops every - n columns, where

is between 1 and 127.

Reset a// tab stops

Mode

IBM

ASCII

<ESC> “R”

Decimal

27 62

Hexadecimal

1B 52

Resets the horizontal tab stops to their power-up values in which a tab stop is set every 8 column starting at column 9. Also clears all vertical tab stops.

Horizontal tab

Mode

Both

ASCII

<HT>

Decimal

Hexadecimal

Moves the print position to the next horizontal tab stop. Ignored if there is no next horizontal tab stop in the current line. Note that when underlining is selected, spaces skipped by horizontal tabulation are not underlined.

Relative horizontal tab

Mode

Std.

IBM

ASCII

<ESC> ‘T’ nl n2

<FS> ‘T’ nl n2

Decimal

27 92

nl n2

28 92

712

Hexadecimal

1B 5C

nl n2

1C 5C

Moves the print position right or left a specified distance (maximum

13.6 inches). Ignored if the resulting position is beyond the right or left margin. The formulas for the distance and direction are as follows:

is between 0 and 63, the print head moves right by

(nl + n2 x

256)/120 inches.

If n2 is between 64 and 127, the print head moves left by

(nl + [n2-

641 x 256)/120 inches.

nZ + n2 x 256.

Dots beyond the right margin are ignored. At the end of bit-image printing the printer returns automatically to character mode.

Print double-density g-bit graphics

Mode

Both

Mode

Both

ASCII

<ESC> “*” n0

nl n2 ml m2 . . .

Decimal

27 42 n0 nl

n2 ml m2 . . .

Hexadecimal

1B 2A n0

nl n2 ml m2 . . .

Selects one of eight graphics modes depending on the value of

and prints bit-image graphics in this mode. See <ESD “K” for information on

nl, n2, ml, rid?, . . . nO

Graphics mode

Normal-density

Double-density

Double-density, double-speed

(60 dots per inch)

(120 dots per inch)

Quadruple-density

CRT graphics, mode I

Plotter graphics

CRT graphics, mode II

(240 dots per inch)

(80 dots per inch)

(72 dots per inch)

(90 dots per inch)

Double-density plotter graphics (144 dots per inch)

Convert graphics density

Mode

Both

ASCII

<ESC> “?”

n m

Decimal

27 63

n m

Hexadecimal

1B 3F

n m

Converts graphics defined by subsequent <ES0 “K”, <ES0 “L”,

<ES0 “Y” or <ES0 “Z” commands to a density mode defined by

<ES0 “*“.

is “K”, “L”, “Y” or “Z”, indicating the mode to be converted.

is a code from CO> to <7> indicating one of the modes of <ES0 “*“.

Print g-pin graphics

Mode

Std.

ASCII

<ESC> ‘LA ” n0 nl n2 ml m?

Decimal

27 94 n0 nl n2 ml mi? . . .

Hexadecimal

IB 5E n0 nl n2 ml mz . . .

. . .

Prints bit-image graphics at 60 dots per inch if nO = 0 or 120 dots per inch if

= 1. The graphics image is 9 dots high and

nl + n2

256

dots wide. Maximum width is 13.6 inches. Dots beyond the right margin are ignored.

ml, m2, . . .

are byte pairs representing 9 vertical dots each. In the leftmost position, the most significant bit of

is the top dot; the least significant bit of

is the second dot from the bottom; the most significant bit of

is the bottom dot; and the other bits of

are ignored. Other byte pairs are similar. The number of data bytes must be 2 x

(nl

x 256). At the end of bit-image printing the printer returns automatically to character mode.

DOWNLOAD CHARACTER COMMANDS

Copy standard characters from ROM into RAM

Mode

Std.

IBM

ASCII

<ESC> l

<FS>

“? <o> <o> <o>

Decimal Hexadecimal

27 58 0 0 0 18 3A 00 00 00

28 58 0 0 0 1C 3A 00 00 00

Copies alI the standard characters to the corresponding download character RAM area, overwriting any download data already present. Ignored when DIP switch 2-l is ON.

Define draft download characters

Mode

Both

ASCII

<ESC> “&” <O> nl n2

m0 ml m2 m? . . . ml1

Decimal

27 38

0 nl n2mOmlm2 m3 . . . ml1

Hexadecimal

1B 26 00 nl

n2mOmlm2 m3 . . . ml1

Defines one or more new draft characters and stores them in RAM for later use. DIP switch 2-l must be OFF; otherwise RAM is used as an input buffer, not for downloading characters, and this command is ignored. Draft mode must be selected before this command is executed.

nl is the character code of the first character defined and n2 is the character code of the last character defined. nl and n2 must both be between 32 and 127 or both be between 160 and 255. nl must be equal to or less than n2. Use of character codes 32 (space) and 127

(delete code) should be avoided if possible.

Each character is defined by an attribute byte (m0) and 11 data bytes

m2, . mll).

The most significant bit of the attribute byte is 1 if the character is an ascender (positioned entirely above the baseline) or 0 if it is a descender (descending below the baseline). The attribute byte also indicates the amount of white space to the left of the character (0 to

7 dots, specified by bits 4 to 6). and the width of the character cell, including this space (4 to 15 dots, specified by bits 0 to 3). The left space and cell width attributes are used only in proportional spacing.

Each data byte indicates eight vertical dots, with the MSB being the top dot and the LSB the bottom dot. These correspond to pins 1 to

8 or 2 to 9 of the print head, depending on whether the character is an ascender or descender.

For further details, please refer to the Chapter 5.

Define NL Q download characters

Mode

Both

ASCII

<ESC> “8~” <O> nl n2 m0 ml m2

ml . . . m46

Decimal

27 38 0 nl n2mOmlm2

rd . . . m46

Hexadecimal

IB 26 00

nl n2mOmlm2 m3 . . . m46

Defines one or more new NLQ characters and stores them in RAM for later use. DIP switch 2-l must be OFF. NLQ mode must be selected before this command is executed. The parameters are the same as for the draft download character command except that the attribute byte specifies right space instead of character width and the dot density is doubled in each direction, so each character consists of 16 dots vertically and 23 dots horizontally and requires 46 data bytes. Dots defined by ml to m23 are printed on the first pass of the head. Dots defined by m24 to m46 are printed on the second pass, the paper being scrolled up half a dot between the two passes. For further details, please refer to the Chapter 5.

Define download characters

Mode

IBM

ASCII

<ES& “=”

n2 <Dc4>

al a2 ml m2 . . . ml1

Decimal Hexadecimal

27 61 0

20 1B 3D 00

a0 al a2 ml m2 . . . ml1 a0 al a2 ml m2 . . . ml1

Defmes one or more new draft characters and stores them in RAM for later use. Draft mode must be selected before this command is executed. nl and n2 give the number of bytes of character data that will follow. a0 is the character code of the first character defined. al and a2 are attributes bytes. ml to mZZ are the character data, and are the same as in <ES0 “W. The attribute byte al indicates whether the character is an ascender (not using the lowest of the nine vertical dots) or a descender (not using the highest dot) and whether it has a downward extension to 12 dots.

The attribute byte a2 gives proportional-spacing information. Bit 7 is ignored. Bits 4 to 6 specify the offset to the first byte printed (0 to 7), enabling leading spaces in the character to be ignored. Bits 0 to 3 specify the width of the character cell (maximum 11 dots). The character will be followed by a mandatory blank dot column which is not included in this width.

Characters defined by this command can be selected by <ESC>“%”

1, <ES0 “I” 4, <ES0 “I” 5, or <ES0 “I” 6. This command is ignored when DIP switch 2-1 is ON.

Select download character set

Mode

Both

ASCII

&SC> “%” “1”

Decimal

27 37 49

27 37 1

Hexadecimal

1B 26 31

18 25 01

Selects the download character set. Ignored when DIP switch 2- 1 is

ON.

Select draft download character set

Mode

IBM

ASCII

<ES0 “I” “4”

<ESC>

"I" <4>

Decimal

27 73 52

27 73 4

Hexadecimal

1B 49 34

1B 49 04

Selects the download character set and draft quality. Ignored if the

(.3WE) button was pressed during power-up or if DIP switch 2- 1 is

ON.

Select draft elite download character set

Wade

ASCII

IBM _

<ESC> “I” “5”

Decimal

27 73 53

27 73 5

Hexadecimal

1B 49 35

1B 49 05

Selects the download character set, draft quality, and elite pitch (12 if DIP switch 2-1 is ON.

Select NLQ download character set

Mode

IBM

ASCII

<ESC>

“I” “6”

<ESC>

"I" <6>

Decimal

27 73 54

27 73 6

Hexadecimal

1B 49 36

1B 49 06

Selects the download character set and near letter quality. Ignored

2-l is ON.

Select ROM character set

Mode

Both

ASCII

<ESC> “Q” “0”

<ESC>

“%” CO>

Decimal

27 37 46

27 37 0

Hexadecimal

18 25 30

1B 25 00

Stops using the download character set and returns to the built-in

ROM character set. Ignored when DIP switch 2-l is ON.

MACRO INSTRUCTION COMMANDS

Define macro instruction

Mode

Both

ASCII

Decimal

27 43 30

Hexadecimal

18 28 .~ 1E

Cancels any existing macro instruction and replaces it with the defined instruction. The defined macro instruction consists of the characters between the “+” and <RS>. These can be any printable characters or control characters except cRS>, up to a maximum of

16 characters.

Execute macro instruction

IModel ASCII

1 Both 1 <ESC> “+” cl>

) Decimal

12743 1

1 Hexadecimal

IlB2BOl

Executes a previously defined macro instruction.

OTHER PRINTER CONTROL COMMANDS

Set MSB to I

Mode

Both

ASCII

<ESC> “>I’

Decimal

27 62

Hexadecimal

1B 3E

Sets the most significant bit of each subsequent byte received to 1, allowing users with a 7-bit interface to access characters with ASCII codes greater than 127.

Set MSB to 0

Mode

Std.

IBM

ASCII

<ESC> “=”

<FS> “C”

Decimal

27 61

26 61

Hexadecimal

1B 3D

1C 3D

Sets the most significant bit of each subsequent byte received to 0.

Accept MSB as is

Mode

Both

ASCII

<ESC> “#”

Decimal

27 35

Hexadecimal

1B 23

Cancels the preceding commands and accepts the most significant bit as it is sent to the printer.

Delete last character sent

Mode

Std.

ASCII

<DEL>

Decimal

127

Hexadecimal

Deletes the last character received. Ignored if the last character received has already been printed, or if the last character received was all or part of a command.

Cancel last line

Mode

Both

ASCII

<CAN>

Decimal

Hexadecimal

Deletes the last line currently present in the print buffer.

lmmedia te print

[Mode 1 ASCII

<p-C> “i” “1”

Both

1 Decimal

27 105 49

27 105 1

[ Hexadecimal

1B 69 31

1B 69 01

Selects the immediate print mode, in which the printer prints each character as soon as received. At every pause in the incoming data stream the printer scrolls the paper up about 2 inches so that the current line can be seen. When the next character is received the paper is scrolled back down and printing continues. This command is ignored when friction feed is used.

Cancel immediate print

Mode

Both

ASCII

<ESC> “i” “0”

Decimal

27 105 48

27 105 0

Hexadecimal

1B 69 30

1B 69 00

Cancels the immediate print mode. The printer waits for each line to be completed before printing it, and does not scroll the paper up and down. This command is ignored when friction feed is used.

Set printer off-line

blade

Std.

IBM

ASCII

<DC3>

Decimal

27 81 22

Hexadecimal

1B 51 16

Sets the printer off-line. The printer disregards all subsequent characters and commands except <DCl>, which returns it to the on- line state. The printer’s

ON LINE

indicator does not go off.

Set printer on-line

Mode

Both

ASCII

<Da>

Mode

Both

ASCII

<ESC> “<“

Decimal

27 60

Hexadecimal

1B 3C

Immediately returns the print head to the left margin, then prints the remainder of the line from left to right. Normal bidirectional printing resumes on the next line.

Manual feed

Mode

Both

ASCII Decimal

Hexadecimal

27 25 0

1B 19 00 sac, ,,(.. <so" ,sr as)" 40 40 48 41 41 20 28 30 29 29

Selects manual sheet feeding even when the optional automatic sheet feeder is mounted. Ignored if DIP switch l-4 is ON (ASF inactive).

Auto feed

Mode

Bo*

ASCII

,,(,, .‘(.,

"4"

Decimal Hexadecimal

27 25 4

19 04

")" ")" 40 40 52 41 41 28 28 34 29 29

Selects the automatic sheet feeder. Ignored if DIP switch l-4 is ON

(ASF inactive).

Eject paper from ASF

Mode

Both

ASCII

<ESC> “R” a(” ..(”

"R"

Decimal Hexadecimal

27 25 02

18 19 52

")" ")" 40 40 82 41 41 20 20 52 29 29

Ejects the current page. Ignored if DIP switch l-4 is ON (ASF inactive).

Set print start position on ASF

Mode

Bo*

ASCII

Decimal Hexadecimal

<ESC>

“T” n

“(”

27 25 84

1B 19 54 n

“(”

"T" ")" ")" n 40 40 84 41 41

n 20 28 54 29 29 n

Skips

n/6

inches at the top of the page, where n is equal to or greater than 1. Ignored if DIP switch l-4 is ON (ASF inactive).

Reset printer

Mode

Both

ASCII

<ESC> “@”

Decimal

27 64

Hexadecimal

1B 40

Reinitializes the printer. Clears the print buffer and returns settings to their power-up values. Does not clear the input buffer or change

ASF selections.

Chapter 5 DOWNLOAD CHARACTERS

With this printer you can create new characters and symbols, download their dot data, and have them printed in place of selected characters in the regular character set. Characters that can be generated in this way range from simple but useful symbols like the check mark through complex Chinese or

Japanese characters.

Regular characters are permanently stored in the printer’s ROM, but characters you design are downloaded and stored in RAM for use.

DESIGNING YOUR OWN DRAFT CHARACTERS

Designing and printing your own characters has two requirements: firstly, designing the shape of the character, calculating the data necessary to make the shape, and sending that data to the printer, and secondly, sending the command to print the downloaded characters instead of the regular characters. There are a number of design constraints for download draft quality characters: l

The matrix or grid on which you design the characters is six boxes wide by nine boxes high. l

Horizontally, dots may be centered in a box, ormay straddle a line, making the actual character grid 11 dots wide by 9 dots high. Vertically, dots can only be centered in a box. See Figure 5-l.

Figure 5-l. Dots can be inside boxes or straddle the vertical lines of the grid

The minimum width of a character is five dots. l

The user-defined characters may use eight dots vertically. l

Dots cannot overlap - that is, you may not have a dot inside a box next to one that is on a line. l

You may define any position in the ASCII table, except the block graphics area when you are downloading in the IBM mode.

Photocopy the grid inFigure 5-2 to help design your new characters. We will use a tiny representation of a car-shaped symbol for our example.

128

ASCII Code:

Descender:

Left space:

Last column: m0 = Descender x I28

+ (Left x 16)

+ Last

Figure 5-Z Use this grid (or one similar to it) to define your own draft characters

Defining the attribute data

Before you start the definition, you will need to decide exactly where in the regularASCI1 set you want to place your characters. After downloading, you access your new character by sending the code for the character you replaced.

ml ~13 m5 m7 m9 ml1 m2 m4 m6 m8 ml0

128

724 66 64 76 76 0

0 4 36 2 72

ASCII Code:

Descender: I

Left space: 0

Last column: 77

mO = Descender x 128

+ (Left x 16)

+ Last

Figure 5-3. Add the values of the dots in each column and write the sum of each mlumn at the bottom

Next you must choose whether to make the car symbol an ascender or a descender. This determines how the character is seated on the line:

Ascender: (:;I:&

Descender: C:l I:-:

We decided that our car symbol will not be a “descender”, so a figure “1” is written next to Descender on the grid. If your character is a descender, write a “0” next to Descender.

Next, you must specify the left space and the last print column of the character.

Being able to specify the width of the character allows you to specify the precise area inside the grid that the character will occupy, so that narrow characters will look attractive next to wide ones.

Acceptable values for the left space are 0 to 7, and the last print column are from 4 to 11.

Our character will occupy from column 1 to column 11, so the left space is

0 and the character width data is 11.

Assigning the character data

Now, we calculate the vertical numerical values of the columns of dots, and enter them underneath the grid. For example, looking at Figure 5-3, we see that in the left-most column there are five dots, and they are sitting in the “64” box, “32”box, “16” box, “8” box, and “4”box. Thus its vertical value is 124.

In the next column, there is no dot straddling the vertical line; its value is recorded as 0. define the character, you wiil substitute your value for each of these letters.

Sample program

To demonstrate how to use the download characters, let’s use the “car” character and some other user-defined characters to print a small graph. This program will do just that:

1000

LPRINT CHR$(27);“&“;CHR$(O);

1010

LPRINT CHR$(60);CHR$(62);

1020 FOR N=60 TO 62

1030 FOR M=O TO 11

1040 READ MM

1050 LPRINT CHR$(MM);

1060 NEXT M

1070 NEXT N

1080 LPRINT

1090 DATA 139, 2. 5, 8,241,

1100

DATA 0,241,

1110 DATA 139,124,

66.

1120

DATA 36. 16. 2, 16, 12. 0

1130

DATA 139. 46, 16, 2, 60, 0

1140

DATA 48, 0, 48, 0, 48, 0

1150 LPRINT CHR$(27) ;“D”;CHR$(ll)

1160 LPRINT CHR$(27) ;“h”;CHR$(l);

1170 LPRINT ” U. S . EXPORTS”

1180 LPRINT CHR$(27) ;“h”;CHR$(O);

;CHR$fO);

1190 LPRINT CHR$(27);“%“;CHR$(l);

1200

LPRINT “AUTOS”;CHR$(9);

1210

FOR I=.4 TO 9.3 STEP .4

1220 LPRINT CHR$(61);

1230

NEXT I

1240 LPRINT

-’

1250 LPRINT "CHEMICALS";CHR$(9);

1260 FOR I=.4 TO 8.7 STEP .4

1270 LPRINT CHR$(60);

1280 NEXT I

1290 LPRINT

1300 LPRINT "GUNS";CHR$(9);

1310 FOR I=.4 TO 1.4 STEP .4

1320 LPRINT CHR$(62);

1330 NEXT I

1340 LPRINT

1350 LPRINT CHR$(9);"+--";

1360 SCALE$="--+--'I

1370 FOR I=2 TO 8 STEP 2

1380 LPRINT SCALE$;

1390 NEXT I

1400 LPRINT "---+'I

1410 LPRINT CHR$(9);" ";

1420 FOR I=2 TO 8 STEP 2

1430 LPRINT u

'I; I;

1440 NEXT I

1450 LPRINT CHR$(27);"%";CHR$(O)

1460 LPRINT CHR$(27);"S";CHR$(O);

1470 LPRINT CHR$(9);

"MILLIONS OF DOLLARS"

1480 LPRINT CHR$(27);"T"

1490 END

DEFINING YOUR OWN NLQ CHARACTERS

As you probably noticed, NLQ characters are printed by two passes of the print head. Half of the character is printed on the first pass, and the remainder on the second pass. The paper is rolled up half a dot height in between passes to let the print head print dots on the second pass that overlap the previous dots, in order to fill in the spaces and produce denser characters. Addition- ally, the print head speed is halved, and the dots are printed at double the density of draft characters. For this reason, NLQ characters can contain up to 23 dots in the horizontal direction.

Fundamentally, the process to define and print downloaded NLQ character is the same as for draft characters, except that you must supply about four times as much character data, and you must design the character with the two passes of the print head in mind. There are small differences in the way the attribute information is processed also.

In the draft quality mode the attribute byte carries the descender data, and specifies the left space and the character width. In the NLQ mode, the first bit also carries the descender data, and the next three bits describe the character’s left space as with the draft characters, but the last four bits describe the right space. Appropriate allocation of data in these seven bits lets you place the character where you like within the grid, with the restriction that the character must be at least 9 dots wide.

Use the grid in Figure 5-4 to help plot the data. Due to the two-pass process,

NLQ characters can contain up to 16 dots vertically. ml to m23 are the data for the first pass, and m24 to m46 are the data for the second pass.

To make the character data easier to calculate, put the first pass dots inside the boxes on the grid when you are designing your characters, and the second pass dots on the lines. Remember that adjacent dots may not overlap on the same pass; in other words, if one dot is in a box, its adjacent dot on the same pass may not be on a line. Therefore, to make smooth characters, put the dots needed to overlap any spaces in a character in the appropriate places in the second pass grid.

If we plot our car-shaped symbol for NLQ, the grid data will look like Figure

5-5.

The defining process is the same as for draft characters, except that you must select NLQ mode, and you must define 46 data. If you wish to print your

NLQ characters with the regular character set, the remarks regarding the

simultaneous use of regular and download characters in the draft character section apply equally to NLQ characters. ml

(1st) n124....

I28

..m23

ASCII Code:

Descender:

Left apace:

Right space: nrO = Descender x I78

+ (Left x 16)

+ Right

2nd:

‘gore 5-4. Use this grid (or one similar to it) to define your own NLQ characters

(1st)

12x ml

..m23

(2nd)

128

I st: 74 38 70 70 726 0 0 0 9 9

8 0

76 7 ? 0 0 70 38 22 6 6

2nd: 28 74 74 74 724 0 64 32 76 0

0 0

32 64 0 0 0 72 72 74 74

74 72

ASCII Code:

Descender: 7

Left space: 0

Right space:

0 nr0 = Descender x 12X

+ (Left x 16) igure 5-5. Add the values of the dots in the boxes first, and then add the value on the lines

MEMO

3

Chapter 6 MS-DOS AND YOUR PRINTER

When using your printer with an IBM PC, PC-XT, or PC-AT or compatible, you will probably be using PC-DOS or MS-DOS as an operating system. A number of software tricks may be useful here. This chapter is not, however, a substitute for the operating system manuals supplied with your computer.

To learn how to print files, etc. it is best to read the relevant parts of these manuals.

INSTALLING APPLICATION SOFTWARE WITH

YOUR PRINTER

When installing application software, you may find that your printer is not specifically mentioned in the lists of printers given for installation. How- ever, this should pose no problem. Read this section, and guidelines provided with your software on printer installation.

If you have your printer set up in standard mode, then choose an Epson FX-

10.50 or EX-1000 as your printer to be selected.

If neither of these are mentioned, choose one of the following (in order of preference): Star NR-10/15, Star ND-10/15, Epson FX86e, Epson FX286e.

If you have your printer set up with the DIP switches to emulate an IBM

Proprinter XL, simply choose this from the list of printers available in the application software list.

If the IBM Proprinter XL is not mentioned, use Proprinter II or Proprinter.

If your software package does not mention printers by name, but asks instead what features your printer is capable of, the most common questions are:

“Can your printer perform a backspace?” and “Can it do a hardware form feed?“. You should answer “Yes” to both these questions.

Other software packages may well allow you to install specific features.

Spreadsheet programs will often ask for the maximum number of columns to be printed. This is given below.

Number of columns

Pica

Elite

Condensed pica

Condensed elite

Proportional

CPI

136

163

17.1 233

20 272

Variable

Sometimes the software installation will ask you for an initialization sequence to return to the default settings. The command for your printer is

<ES0 @.

Make sure that the DIP switches are set for the right printer emulation, and that you have selected the appropriate character set using the DIP switches.

If you are in doubt about the configration of your application software, seek expert advice. Your software supplier will probably be your most conve- nient reference.

EMBEDDING PRINTER COMMANDS

Many word-processors and other software lack commands for changing type style, or printing double-size characters, and some do not even support bold printing or italics. Your printer therefore has commands that can be embedded in documents to control these functions without software help.

The commands consist of a capital letter enclosed in double parentheses, followed by a digit:

Type style (Font):

((F))O

((F))l

m-9)2

W))3 c(P))9

Courier

Sanserif

Orator with small capitals

Orator with lower case

Draft

Size:

(WXJ

((S)) 1

KS)P

C(S))3

Standard size

Double width

Double height

Double width and height

Bold:

Italic:

W)O

NW) 1

((I))0

((1)) 1

Non-bold

Bold

Non-italic

Italic

If you want to print a title in double-size Orator with small capitals, then change to regular-size Courier for some text that includes italics, you can use these commands as follows:

File as seen on computer screen:

((F))2

Printer

((S))3

Commands t(F) 10 ((S) )O

Type style,

((1))lItalic size, bold print,

((1))Ocommands

((1))lanywhere ((1))Oin can and a document. be embedded

Printout:

PRINTER CC~MMANDS

Type style, size, bold print,

Italic

commands can be embedded

anywhere

in a document. and

When you use these commands there are several points to note: l

The type style (0;)) and italic ((I)) commands are ignored if the (m) button was held down when power was switched on. l

The bold command ((B))l gives double-strike printing. In draft mode you may prefer to use emphasized printing, which requires a software command or escape sequence. l

A line consisting of commands alone prints as a blank line. l

Software does not cannot trust your software to give you the correct line width. The printed line may be considerably shorter than the line on the screen; the missing space is the space that was occupied by the commands.

One way to handle the last problem is to prepare your document without the commands, then insert them as a final step, with the margins released. The find, replace, and copy functions of word-processing software can be helpful here.

If you do not use these commands or the panel controls, the printer will print standard-size, draft, non-bold, non-italic characters.

The printer supports various commands in addition to the above, such as quadruple-size printing.

Most of these other commands consist of the escape code followed by one or more letters or numbers.

If your software enables you to place the escape code in your files, or if you were able to define this as a user option during installation, you can also embed these escape sequences.

PROGRAMMING THE PRINTER WITH DOS

COMMANDS

If your system includes the file PRINT.COM you can use the main DOS printing command. Simply type the word PRINT followed by the name of the file you want to print. To print a file named README.DOC, for example, type:

A>PRINT README.DOC

The computer may respond with the following message, asking which printer to use:

Name of list device

IPRNI:

If your computer is connected to only one printer, press RETURN to select the default choice (PRN). Printing will begin and the A> prompt will reappear. You can execute other commands or programs while the file is being printed.

A single PRINT command can print two or more files. List the file names consecutively on the same line, or use wild-card characters (* and ?). Each file will be printed starting on a new page. The PRINT command also has control options. For example, you can terminate a printing job in progress with the /‘I option. (The printer may not stop printing immediately it may have considerable data stored ahead in its buffer.) For the /r option, type:

A>PRINT/T

See your DOS manual for further information about the PRINT command.

If your system does not include PRINT.COM, you can print files by using the PRN device name in COPY or TYPE commands such as the following:

AXOPY README.DOC PRN

A>TYPE README.DOC >PRN

i i

COPY and TYPE do not permit you to execute other commands while the file is printing.

If you want a particular font style, or print pitch, you

make

from the control panel before you start printing. See Chapter 2.

If you print from the DOS command level very often, it will be advantageous to create a printer setup file. Then instead of setting font style etc. manually each time, you can complete the setup with a single command from your computer. For example, you can create a file containing printer commands to select nearletterquality, and select elite pitch. You can find the commands in Chapter 4. We suggest the following: l

Near letter quality l

Elite pitch

<ESC> “x” “1”

<ES0 “!”

<l>

<ESC> “!” cl> is a powerful command that, in addition to selecting elite pitch, cancels unwanted features such as underlining which might be left from previous commands. The angle brackets around the <l> indicate character code 1, which is a control code, not the printable digit “1”.

You may want to place additional commands in this file, such as left and right margins, line spacing and bottom margin commands. Or you may want to create a variety of setup files with a different set of commands in each.

To avoid excess line feeds, you should place the commands on one line in the setup file. You may or may not be able to generate a setup file with word- processing software; it depends on whether your software lets you enter control codes. If your system includes the file EDLIN.COM, however, you can easily create a setup file with the DOS line editor.

An appropriate name for this setup file would be NLQELITE.DAT. To use the DOS line editor, type the command EDLIN NLQELITE.DAT, then type the underlined parts of the following display. Press RETURN at the end of each line. Don’t type the symbol “*“. This symbol means to hold the CTRL key down while pressing the next key: for example, “V means to type CTRL-

V. AC means to type CTRL-C, which indicates the end of the input.

A >EDLIN

New file

81

*V indicates that the following character is a control code. “V[ enters the

<ES0 code. <ESC> has character code 27, and “[” is the 27th character in

ASCII sequence from A. Similarly, “VA enters the control code cl>. See your DOS manual if you need further information about EDLIN.

You can now set up the printer by sending it the file NLQELITEDAT. To avoid unnecessary logging of commands, switch hard-copy output off (by pressing CTRL-PRTSC ifhard copy is on). To print the file README.DOC in NLQ elite type, give the following two commands:

AXOPY NLQELITE.DAT FRN

A>PRINT README.DOC

For greater convenience you can make a batch file that will set up the printer and print any specified file with a single command. To create such a batch file with the name NLQPRINT.BAT, type in the first four lines shown next.

“Z means to press the CTRL and Z keys simultaneously. To use this file to print README.DOC, type the fifth line.

AXOFY CON NLQPRINT.BAT

COPY NLQELTTE.DAT PRN

PRINT %1

^Z

A>NLQELITE README.DOC

The first above line is a copy command from the CONsole screen to a file named NLQPRINT.BAT. The next two lines are the contents of this file. The

% 1 is a dummy parameter: whatever file name you type after NLQPRINT will be substituted for %l and printed.

PROGRAMMING WITH BASIC

As an example of programming the printer on Microsoft BASIC, we have listed the program for the IBM-PC. This program runs in the printer’s

Standard mode, and the downloadable condition (DIP switch l-6 ON and

DIP switch 2-l OFF).

1000 ’ set control codes _-_--.-_____---____-_~.--------___

1010 E$=CHR$(27) 'Escape code

'Draft quality 1020 D$=E$+"x"+CHR$(O)

1030 N$=E$+"x"+CHR$(l)

1040 C$=E$+"kO"+N$

1050 S$=E$+"kl"+N$

1060 Ol$=E$+"k2"+N$

1070 02$=E$+"k3"+N$

1080 H$=CHR$(9)

'Near letter quality

'Courier characters

'Sanserif characters

'Orator with small capitals

'Orator with lower case

'Horizontal tab

82

1090 P$=E$t"P"

1100 ' Start printing

'Pica pitch

____________________

1110 WIDTH "LPT1:",255

1120 LPRINT E$;"D";CHR$(3):CHR$(25);CHR$[Ol

-.--

'Set HT

----

1130 LPRINT C$;"Type styles are:"

1140 LPRINT H$;D$;"Draft characters,"

1150 LPRINT H$;C$;"Courier characters,"

1160 LPRINT H$;S$;"Sanserif characters,"

1170 LPRINT H$;Ol$;"Orator with small capitals. or"

1180 LPRINT H$;02$;" with lower case characters,"

'Select italics

1200 LPRINT H$;02$;"and ";Ol$;"italics ";S$;"for 'I;

1210 LPRINT C$;"all ";D$;"styles."

1220 LPRINT E$;"5"

'Cancel italics

1230 LPRINT C$;"Print pitches are:"

1240 LPRINT H$;P$: "Pica pitch

(10 CPI),";

1250 LPRINT H$;E$;"M";"Elite pitch (12 CPI)."

1260 LPRINT H$;CHR$(15); 'Condensed pitch

1270 LPRINT P$;"Condensed pica pitch (17 CPI).";

1280 LPRINT H$;E$;"M";"Condensed

1290 LPRINT P$; elite pitch (20 CPI).";

'Pica pitch

1300 LPRINT CHR$(18)

'Cancel condensed print

1310 LPRINT H$;E$;"pl";

'Select proportional spacing

1320 LPRINT "proportional spacing for all pitches,"

1330 LPRINT E5;"pO"

'Cancel proportional spacing

1340 LPRINT H$;E5;"W1";"Expanded,";E$;"WO";

1350 LPRINT H$;E$;"wl";"Double-height, ";E$;"wO"

1360 LPRINT H$;E$;"h";CHR5(1);"Doub1e-sized,"

1370 LPRINT H$;E$;"h";CHR5(2);"Quad-sized.";

1380 LPRINT E$;"h";CHR$(O)

1390 LPRINT :LPRINT

1400 LPRINT E$;"Q";CHR5(49)

'Set right margin

1410 LPRINT C$;"Various line and character spacings:"

1420 LPRINT E5;"al"

1430 FOR I=1 TO 7

'Center text

1440 LPRINT E$;"A";CHR$(I);

'Set line spacing

1450 LPRINT E5;" ";CHR$(I);

'Increase

1460 LPRINT "THE SPACINGS ARE CHANGED" character space

1470 NEXT I

1480 FOR I=7 TO 1 STEP -1

1490 LPRINT E$;"A";CHR$(I);

1500 LPRINT E$;" ";CHR$(I);

1510 LPRINT "THE SPACINGS ARE CHANGED"

1520 NEXT I

1530 LPRINT E5;"aO" 'Left justify

1540 LPRINT E5;"3";CHR5(36);

1550 LPRINT E$;" ";CHR$(O);

'Set l/6" line spacing

'Normal character space

1560 LPRINT :LPRINT

1570 LPRINT C5;"Other features:"

1580 LPRINT H5;E5;"E";"Emphasized";E5;"F";", 1:;

1590 LPRINT E5; "G";"Double-strike";E$;"H";",

1600 LPRINT E$; "-I"; “Underlining”;E$;

"-0"; ",'I

;

1610 LPRINT H$;E$;"-l";"Overlining";E5;"~O";", :I;

1620 LPRINT E$; "SO";"SUPERSCRIPT";E5;"T";" and ;

1630 LPRINT E5;"S1";"SUBSCRIPT";E5;"T"

1640 GOSUB 2100

1650 LPRINT H$;C$.;"Download characters: 'I;

1660 LPRINT D$;E$:"%l";

1670 FOR I=1 TO 5

'Select download character

'Print downloaded character

1680 LPRINT CHR5(60);

1690 NEXT I

1700 LPRINT D$;E$;"%O":

1710 GOSUB 2180

'Select normal character

1720 LPRINT C$;E$;"%l";

1730 FOR I=1 TO 5

1740 LPRINT CHR$(60);

1750 NEXT I

'Select download

'Print downloaded character character

1760 LPRINT D$;E$;"%O" 'Select normal character

1770 LPRINT H$;C$;"Various dot graphic densities:"

1780 DIM LOG05(4)

1790 RESTORE 2370

1800 FOR ROW=1 TO 4

1810 FOR COL=l TO 65

1820 READ-DG

1830 LOGO5~ROW)=LOGO5(ROW)+CHR5~DG)

1840 NEXT COL

1850 NEXT ROW

'Set 8/72" line spacing

1860 LPRINT E$;"A";CHR$(8);

1870 FOR ROW=1 TO 4

1880 LPRINT H5;"

1890 FOR B=O TO 4

1900 IF B=2 THEN 1940

1910 LPRINT E$;"*";CHR$(B);

'Select dot grapgics

1920 LPRINT CHR5(65);CHR$(O);LOGO$(ROW); mode

1930 LPRINT " 'I;

1940 NEXT B

1950 LPRINT

1960 NEXT ROW

1970 LPRINT

1980 FOR ROW=1 TO 4

1990 LPRINT H5;" ";

2000 FOR B=5 TO 7

2010 LPRINT E$;"*";CHR$(B); 'Select dot grapgics mode

2020 LPRINT CHR5(65);CHR5(O);LOGO$(ROW);

2030 LPRINT " ":

2040 NEXT B

2050 LPRINT

2060 NEXT ROW

2070 LPRINT E$;"@"

2080 END

'Initialize printer

2100 ' Define draft download character -----------.----.----------

2110 LPRINT D$;E$;"&";CHR5(0);CHR$(60);CHR5~6D~;

2120 RESTORE 2280

2130 FOR M=O TO 11

2140 READ MM

2150 LPRINT CHR$(MM):

2160 NEXT M

2170 RETURN

2180 ' Define NLQ download character -------.--------------

2190 LPRINT C$:E$;"&";CHR5(0~:CHR5~60);CHR$(60~;

2200 RESTORE 2310

2210 FOR M=O TO 46

2220 READ MM

2230 LPRINT CHR$(MM);

2240 NEXT M

2250 RETURN

I DATA ___________-----------------------------------

2260

2270 0 Draft download character .

2280 DATA 139,124, 0, 66, 4. 64, 36, 16, 2. 16, 12, 0

2290 I

2300 3 NLQ down~oa,j ,-haracter --___-_--_------------------

2310 DATA 128, 14. 16, 38. 1. 70. 1. 70, 0,126, 0. 0

2320 DATA 70. 0. 38, o, 22, 9. 6. 9. 6, 8, 6. 0

2330 DATA 28, 32, 14. 64, 14. 0. 14. 0,124, 0. 0, 12

2340 DATA 64, 12, 32, 14, 16. 14. 0. 14. 0, 12. 0

2350 '

2360 ' Dot graphics ---

2370 DATA 0. 0. 0, 0, 1, 3. 7. 7. 7. 15, 14, 14

2380 DATA 14, 14. 14, 7, 7. 3, 3, 15. 15, 15, 0. 0

2390 DATA

2400 DATA

2410 DATA

2420 DATA

2430 DATA

2440 DATA

2450 DATA

2460 DATA

2470 DATA

0, 0. 6, 7, 7. 7, 7. 7. 7. 7. 7. 6

6, 0, 0, 7, 7. 7. 7. 7. 7, 7. 7. 7

7, 7. 0, 0. 7. 7. 7. 7. 7. 7. 7. 7

7. 7. 0. 0. 0

0. 0, 60,255,255,255.255.255.143, 15, 7, 7

7, 7. 3. 3. 3,131,193,241,240,240, 0. 0

0. 0. 0, 0,224,255,255.255,255,255.

0. 0. 1. 3, 31.255.255.255.255.255.255.

31, 0

0, 0, 0, 1, 7, 31.255.252.240.192.128. 0

2480 DATA

2490 DATA

0, 0. 0. 0. 0

0. 31, 31. 3,129,128,1.92.192.192.192.192.224

2500 DATA 224,224,224,240.255,255.255.255.255.127.

2510 DATA 0, 0. 0. 0. 0,192,255,255,255.255.255.

2520 DATA 15, 63,252,240,192,

0.240.255.255.255.255.255

2530 DATA 7, 15,127,252,240.192. 0. 0, 0, 0. 0. 0

2540 DATA

2550 DATA

0. 0. 0. 0, 0

0,248,248,240.224.224.112.112. 56, 56. 56. 56

2560 DATA 56,120,120,240,240.224.224.192,128~

2570 DATA 0, 0. 0. 0, 0,

0, 0.

0,128,248,248,248,248,240

2580 DATA 192. Cl, 0, 0. 0. 0,240,248,248.248.248.240

2590 DATA 192, 0. 0. 0, 0, 0. 0. 0. 0, 0. 0, 0

2600 DATA 0. 0. 0, 0. 0

How the program works

This program begins by assigning a number of printer commands to BASIC string variables (lines 1000 to 1090). You can find most of these commands near the beginning of chapter 4.

The WIDTH “LPTl:” 255 statement in line 1110 means infinite line width.

It prevents the IBM-PC from inserting unwanted carriage returns and line feeds in graphics data.

Actual printing begins in line 1120. Using the preassigned commands, the program prints samples of its different font styles, including a line showing all styles in italics, followed by samples of the print pitches, then some double and quadruple-sized printing.

Next comes the central attraction of the program: a line of text printed fourteen times in expanding and contracting loops to give a barrel effect. The work is done by four printer commands: a command setting the right margin

(line 1400); a centering command (line 1420); a command to vary the line spacing (lines 1440 and 1490); and a command to micro-adjust the space between characters (lines 1450 and 1500).

Next the program returns to normal spacing and gives a demonstration of the printer’s word-processing abilities: bold printing, underlining, subscripts, etc.

The row of automobiles in the next printed line is created by downloading two new character patterns, which are printed in place of the character “c“

(character 60). Details can be found in Chapter 5.

The final part of the program uses dot graphics to print some “SW” logos with various densities. The dot pattern of the logo was originally laid out on graph paper, then converted to the data in lines 2370 to 2600 with the help of a calculator. Each number represents eight vertical dots. (See “Graphics commands” in Chapter 4 for details.)

The pattern is printed in four rows, each eight dots high and 65 dots wide.

Lines 1800 to 1850 read the dot data into a string array variable named

LOGO$. Line 1860 sets the line spacing to 8/72 inch so that the rows will connect vertically. The loop in lines 1870 to 1960 does the printing in four passes of the print head.

Type styles are: i !. “, / ,:, , !. j <‘:‘;j

Courier characters,

Sanser if characters,

ORATOR WI-TH SMALL CAPITALS, OR

with lower case characters,

ITS Gf- a ! 1 ' i..

Print pitches

Pica pit.ch

proportional

are:

(10

WI),

Elite

pitch (12 CPI

1, elite pitch (20 CPII, spacing for all pitches.

Various line and character spacings:

Other features:

Emphasized,

Double-strike,

&Jnderl ininq.

SUPERSCR1PT and SURSCFIIPT

Dt::wn 1 odd characters : ) ..: ;i i .J::.&&W&

Var10us dot graphic densities:

Modifications for IBM mode

This program can also be run in IBM mode (DIP switch l-6 OFF) if you change a few of the lines as shown below to allow for difference in some of the commands. You will get a cylinder instead of a barrel effect, becuase the

IBM mode does not have any command to micro-adjust the character spacing.

1090 P$=CHR$(lB)

1190 LPRINT CHR$(28):"4";

1220 LPRINT CHR$(28);"5"

'Pica pitch

'Select italics

'Cancel italics

1280 ' LPRINT H$;E$;"M": "Condensed elite pitch (20 CPI).";

1400 LPRINT CHR$(28);"Q";CHR$(49)

'Set right margin

1440 LPRINT E$;"A";CHR$(I);E$;"2":

'Set line spacing

1450 ' LPRINT E$;" ";CHR$(I):

'Increase character space

1490 LPRINT E$;"A";CHR$(I);E$;"2";

1500 ' LPRINT E$;" ":CHR$(I);

1550 ' LPRINT E$;" ";CHR$(O);

'Normal character spdce

1860 Lp~1N-r E$;"A";CHR$(8);E$;"2"; 'Set 8/72" line spacing

Chapter 7 TROUBLESHOOTING

AND MAINTENANCE

The following section on troubleshooting and maintenance is intended only as a brief guide to these functions. Remember that your printer is a highly sophisticated electronic device, which also contains high voltage inside. For that reason, only carry out those operations described in this chapter.

CAUTION: Any attempt to carry out operations other than those described here may result in electric shock and/or damage to the printer.

When carrying out any repairs or maintenance, always follow the instructions carefully.

TROUBLESHOOTING

Your printer is a reliable piece of precision machinery, which should not cause you any trouble, provided it is used and treated sensibly. However, the few elementary tips below should avoid you having to make unnecessary service calls. The following table gives you ideas on where to look in this section if you experience faults:

Remember - it is better not to attempt operations or repairs above your level of competence. Otherwise, you run the risk of damaging the printer.

Power supply

If the

POWER

indicator does not illuminate, check the following:

Possible remedy ,

Turn off the printer ensure the power cable is securely connected, and then turn the printer back on.

Turn off the printer, unplug it, and try with another appliance to determine if electricity is being supplied to that outlet.

Check the bottom panel of your printer to ensure that the outlet voltage corresponds to the voltage required by the printer. If they do not match, DO NOT try to operate the printer. Contact your supplier.

Printing

If your printer does not print, or suddenly stops printing, check the following:

Check

Is the interface cable connected securely?

Is the

ON LINE indicator illuminated?

Is the POWER indicator flashing?

Is the paper caught up inter- nally?

Possible remedy

Check both ends of the cable - printer and computer to make sure that the connector is firmly in position.

If itisnot,press thee

ON LINE

Jbutton tosettheprinter on-line.

If it is, the paper has run out. Load more paper.

Is the ribbon caught up around the print head?

Is the software you are using properly installed for your minter?

Can the printer perform self- test operations?

Turn off the power, remove the jammed paper, replace, tumontheprinter, andcontinueprinting.Makesurethat the leading edge of the paper is smooth and uncreased.

Turn off the power, remove the ribbon, retension it, and replace it. This problem occurs most frequently with a worn ribbon, so you may need to replace the ribbon.

Check the installation settings in your software, and reinstall if necessary.

Turn the printer off, and turn it on again, holding down one of the buttons to perform a self-test. If these do not work, contact your dealer.

If the print is faint, or uneven, check the following:

Check

Is the ribbon properly installed?

Is the ribbon worn out?

Possible remedy

Check and reinstall if necessary.

The ribbon has a long life, but evenLually will need replacing. Fit a new ribbon cartridge if necessary.

If dots are missing in the printing, check the following:

Check

Are dots missing at random in the printing?

Possible remedy

The ribbon has become slack. causing it to get caught up. Stop printing, remove the ribbon cartridge, retension and replace it.

The print head is damaged. Stop printing, and contact your supplier for a new print head.

Is a line of dots missing con- sistently throughout the printing?

If your application software cannot print the fonts or characters selected, check the following:

Check

Is your application software properly installed?

Are fonts not being selected properly?

Are characters other than those expected being printed?

Possible remedv

Check the software installation, and re-install the software if necessary.

Check the software installation, and insert the commands necessary for font changes into the software.

Either you are using the wrong International Character

Set (reset with DIP switches or software commands), or you have the wrong character set selected (for example if characters other than IBM block graphic characters are being printed). Correct this with DIP switches or the appropriate software sequences. i

If the printout is not what is expected:

Check

Is the printer installed correctly?

Is the printer not printing anything that you are expect- ing?

Possible remedv

Your software may think that it is driving a different emulation to the one actually set. Check the DIP switch settings to make sure you have the right emulation.

Use the Hex Dump mode to analyze the output from the computer to the printer. This will enable you to determine that the right escape sequences, etc are being transmitted.

Paper feeding

If cut sheet paper (without the ASF) is not feeding smoothly, check the following:

Check

Is the paper release lever pushed back (to the b position)?

Is the paper guide in place and vertical?

Are the left and right guides too close together?

Possible remedy

Set the release lever to the C position.

The paper guide should be in place vertically for cut sheets to feed smoothly.

If the left and right guides are too close together, the paper will not feed smoothly. Move them a little further apart to allow the paper to feed freely.

If it is, then deselect it. Is the ASF selected with the

DIP switch settings?

Are you trying to feed paper using the front panel buttons while the

LINE indicator is illuminated?

Is the paper too thick?

You can only feed paper in this way when the printer is off-line. Set the printer off-line and then feed paper.

Are forms jamming between printing surface and the platen?

There are limits to the thickness of paper that can be fed in thii way. Try with thinner paper.

Clean the surface of the platen roller with a cloth barely dampended with a little alcohol.

If fanfold (continuous) paper is not being fed correctly using the tractor feed, check the following:

Possible remedy

Makesurethereleaseleverispushed to the b position.

Check

Is the paper lever pushed to the & position?

Is the paper guide in the vertical position?

Are the holes on each side of the paper aligned with regard to each other in the sprockets?

Are the sprockets too close or too far apart?

Are the sprockets locked in position and the covers closed?

When using the tractor feed, the paper guide should be horizontal.

If the two sides of the paper are out of alignment, realign them so that the sprocket holes match up.

Misalignment of the sprockets, making the paper too loose or too tight, will prevent a smooth paper feed.

Correct this if necessary.

Check

Is the paper feeding freely into the printer?

Possible remedy

The paper should not be too far from the printer (less than 1 meter/ 3 feet), and there should be no cables or other obstacles obstructing its path. The paper should also be feeding straight into the printer, and an angled feed may cause jams and blockages.

You can only feed paper in this way when the printer is off-line. Set the printer off-line and then feed paper.

Are you trying to feed paper using the front panel buttons whilet.heONLlNEindicatoris illuminated?

Is the paper too thick?

There are limits to the thickness of paper that can be fed in this way (one top copy and two NCR copies). Try with thinner paper.

If the ASF is not operating or is not feeding paper correctly, check the following:

Check

Has the ASF option been selected with the DIP switch?

Is the release lever set to the b position?

Is the ASF correctly mounted?

Is paper caught up neaT the print head?

Are the left and right guides too close together?: -

1 Possible remedy

Select this option

The release lever should be set to the single-sheet position.

Make sure that the ASF is properly seated on the printer.

Stop printing, remove the jammed sheet (you may have to remove the ASF for this), and continue.

If the left and right guides are too close together, the paper will not feed smoothly. Move them a little further

Is there too much paper in the paper feed hopper or stacker?

Was the paper fanned before being fed into the ASF?

Has the paper been used already or is it creased?

Are you trying to feed paper using the front panel buttons whiletheONLlNEindicatoris illuminated?

Is the paper too thick or too thin?

The ASF’s paper feed hopper and stacker can hold 120 sheets each. Make sure that there is no more paper than this in either the hopper or stacker.

If this is not done, paper jams may occur. Remove the stack of paper from the ASF and fan it before reinsert- ing.

Only new, uncreased paper should be used with the

ASF.

You can only feed paper in this way when the printer is off-line. Set the printer off-line and then feed paper.

There are limits to the thickness of paper that can be fed in this way. Try with different paper.

If the paper park facility does not appear to be working correctly, check the following:

Check

Is the paper release lever in the C position?

Has the fanfold paper been properly parked?

Possible remedy

The paper release lever must be set to the & position after the fanfold paper has been parked.

Make sure that the

POWER indicator comes on flashing after the fanfold paper has been parked.

If text is being printed all on one line, or with extra blank lines, check the following:

Check

Is the text all on the same line?

Is text being printed with extra blank lines?

Possible remedy

Carriage returns are not being expanded to

<CR> + <LF> pairs. Check the DIP switch setting and correct.

Two line feeds are being printed. Either make your software print just a carriage return or (if this is not possible), set the AUTO LF to OFF with the DIP switch setting.

If the page length and margins are not what is expected, check the following:

Use the Micro Feed facility to adjust the print position

Use the DIP switch to set up the correct page length, or

MAINTENANCE

Essentially, your printer is a robust piece of equipement, but should be treated with a modicum of care in order to avoid malfunctions. For example: l

Keep your printer in a “comfortable” environment. Roughly speaking, if you are comfortable, then the environment is suitable for your printer, too

(see Chapter 1). l

Do not subject the printer to physical shocks or excessive vibration. l

Avoid over-dusty environments. Dust is the enemy of all precision mechanical devices. l

To clean the exterior of the printer, use a barely damp cloth (use either water with a little detergent or a little alcohol), but do not allow any liquid to fall inside the printer. l

The interior of the printer may be cleaned with a small vacuum cleaner or a compressed-air aerosol (sold for this purpose). When performing this operation, be sure not to bend or damage any cable connections or electronic components.

REPLACING THE PRINT HEAD

This is not a job which you will need to do very often. The print head has been designed to give a life about 100 million characters. In normal everyday use, this will mean years of lift. However, if the print quality is faint, even after I you have changed the ribbon or you have adjusted the gap between the print head and the platen (see Chapter l), the print head will need replacement.

Only use a replacement print head as recommended by your supplier.

1. Turn OFF the printer, and unplug the power cord.

2. Remove the top cover and ribbon cartridge.

3. If the printer has been in operation immediately before this operation, the print head will be hot. Allow time for the print head to cool before attemping to work on it.

4. Move the print head carriage toward the right until you can see the connector cover. Remove the connector cover and pull the cable free from the connector.

5. Unscrew the two screws that hold the print head in place and set them aside.

Figure 7-7. Replacmg the print head

Screws

6. Disengage the cable from the tabs holding it down, then remove the print head.

7. For easy installation of the new print head, move the carriage toward the left end of the rail.

8. Place the new print head on its support, seating it on the two pins.

9. Thread the new cable the same way as the old, securing it under the three tabs on the print head carriage.

10. Plug the cable into the connector, inserting it as far as it will go.

11. Fasten the print head down with the two screws.

12. Move the carriage back toward the right and replace the connector cover.

Slide the connector cover to the left until it locks into place.

13. Replace the ribbon cartridge and top cover, and plug the power cord back in.

MEMO

Chapter 8 SPECIFICATIONS

Printing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Impact Dot-matrix

Printing speed ..,............................. 150 cps (Draft pica)

37.5 cps (NLQ pica)

Print direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bidirectional, logic-seeking

Unidirectional, logic-seeking

(selectable)

Number of print pins . . . . . . . . . . . . . . . . . . . . . . 9

Line spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . l/6, l/8,

n/72,

n/216 inches

Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASCII

International

IBM special

IBM block graphic

Download

14 sets (*)

111

255

* USA, France, Germany, England, Denmark I, Sweden, Italy, Spain I,

Japan, Norway, Denmark II, Spain II, Latin America, Denmark/

Norway

Number of columns . . . . . . . . . . . . . . . . . . . . . . . CPI

Pica 10

Elite 12

Condensed pica

Condensed elite

Proportional

17.1

136

163

233

272

Variable

Character dot matrix . . . . . . . . . . . . . . . . . . . . . . 9 x 11 (Draft) l8x23(NLQ)

Bit image dot-matrix . . . . . . . . . . . . . . . . . . . . . . DPI

8-pin normal 60

8-pin double

8-pin high-speed double*

120

8-pin quadruple

8-pin CRT I

8-pin CRT II

8-pin plotter

8-pin double-plotter g-pin single g-pin double

240

144

120

8 x 816

8 x 1632

8 x 3264

8 x 1088

8 x 1224

8 x 979

8 x 1958

9 x 816

9 x 1632

* It is impossible to print adjacent dots in the mode marked with an asterisk c*>.

Paper feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Friction and push tractor (standard)

Pull tractor (option)

Paper feed speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 inches/second max

Paper width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cut sheet 6”-16.5”

Fanfold (continuous)

4”-16”

Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Original +2 copies

Maximum buffer size . . . . . . . . . . . . . . . . . . . . . Without Download

With Download

15kB

1 line

Emulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Epson mode

IBM Proprinter mode

Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centronics parallel (standard)

RS-232C serial (option)

Ribbon type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . On-carriage, dedicated

Black

Ribbon life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 million characters (draft pica)

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...590(~) x 332(d) x 127(h) mm

23.2(w) x 13.1(d) x S(h) in

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Skg (18.71b)

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120VAC, 220VAC, 240VAC, 50/60Hz

(varies according to the country of pur- chase)

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic sheet feeder

RS-232C interface

Pull tractor feed

The following describes the pinout of the parallel (Centronics-type) interface connector (signals which are low when active are overlined):

34,35

EXT GND

N/C

SELECT IN

External ground

Always high

102

chapter 9 CHARACTER SETS

This chapter gives tables of the printer’s standard and IBM character sets.

The decimal character code of each character is shown in an inset to the lower right of the character.

The hexadecimal code can be found by reading the entries at the top and left edges of the table. for example, the character “A” is in column 4 and row 1, so its hexadecimal character code is 4 1. this is equivalent (4 x 16 + 1 = 65) to decimal 65, the number in the inset.

Control codes recognized by this printer are indicated by abbreviations inside pointed brackets.< >.

B a g

- r

- s

Hexadecimal value

(IOV” order)

103

STANDARD CHARACTER SET

1 641 1 sol

1 9hl

1112)

104

1 41

I

1 201

-0

1 361

I 6el

(

1 e41

IlOOl

II16

+=

1 11 27

(FT)

(CR) j--E- 1

1 131

1 291

I 43

._.

1 451

‘..,

I 59 I 75 1 91

1 611

1 771

160 l-76 1 iv 1

1 931

1 107

1 123

m

II091

I1251

(DEL?

126

105

IBM CHARACTER SET #2

106

(DC2)

3 t

/--T

(Dc4) s

”

B c

A v

1-l

h

1

/-iG

e5

r

t f

84

j-iii

”

1 01

1 241 I 401

I 561

1 721

(ESC)

1 -+

I ;

1 581

IK 1 n m

106

c

1 I ii

t-3

9 !2

E

(1441

n d

I 1601

El

:::

::: -

11761

c

I1921

D

ll.

I2081

E

F

224

240

107

IBM CHARACTER SET #1

Other characters are identical to character set #2.

The duplication of control codes enables systems with a 7-bit interface to obtain control functions when the most significant bit is set to 1 by the

<ESC> “>” command.

108

IBM SPECIAL CHARACTER SET

Additional characters can be printed by special commands.

I

109

INTERNATIONAL CHARACTER SETS

When an international character set is selected DIP switches 2-2 to 2-4 or by a command from software, the following changes are made in the character set:

U.S.A.

64 91 92 93 94 96 123

124 125 126 155 157

# $ @ [ 1, I ^ - { I } -. t’ Y

See Chapter 3 for the DIP switch settings.

The commands for selecting the international character sets are:

Standard mode: <ES0 “R” n IBM mode: cFS> “R” n

Where n means character code n, i.e. CHR$(n) in BASIC. The values of II are:

0 U.S.A.

1 France

2 Germany

5 Sweden

6 Italy

7 Spain I

10 Denmark II

11 Spain II

12 Latin America

3 England 8 Japan

4 Denmark I 9 Norway

13 Denmark/Norway

110

1NDEX

El

Absolute horizontal tab, 57

Ascender, 6 1,7 1

Auto feed, 67

Automatic carriage return, 30

Automatic line feed, 32,55

Automatic sheet feeder, 8,31,67, 101

IBI

Backspace, 55

Bail lever, 3, 10, 13

BASIC, 24,72-73,82

Beeper, 66

Bidirectional printing, 67

Bit-image printing, 58-60,86

Bold printing, 37

Bottom feed, 13

Bottom margin, 50

Buffer, 28,32, 100

Cancel command, 65

Carriage return, 54

Centering, 55

Channels of vertical tab stops, 52

Character codes, printing of all, 40

Character set commands, 39-41

Character sets, 99,104-l 10

Character size and pitch commands,

41-46

Character spacing, 44

Cleaning, 95

Column width, 99

Condensed pitch, 19,42

Connector, 3,6

Control panel, 17

Courier type style, 20,35

IDI

DIP switches, 29-32,78

Delete, 65

Descender, 61,7 1

Dimensions of printer, 101

Dot matrix size, 100

Double-size characters, 44,46

Double-strike printing, 37

Download character commands, 60-63

Download characters, 32,69-75

Draft quality, 20,34,60,63,69-73

Elite pitch, 19,34,41,63

Emphasized printing, 36

Emulation, 3 1,77, 100

Entry slot, 3

Environmental requirements, 1

Escape sequence, 33

Expanded printing, 42

IFI

Fanfold forms: loading, 11 parking, 15 specifications, 102 unparking, 15

Fixed spacing, 43

Font control commands, 34-39

Font style, 35

Form feed, 26,5 1

Gap, 16

Graphics, 86

Graphics commands, 58-60

111

El

Hexadecimal dump, 23-25

Horizontal position commands, 53-57

Horizontal tabulation, 57

/I/

IBM character sets, 39, 106-109

IBM mode, 31,88

IBM-PC, 25

Immediate print, 65

Interface: signals, 102 specifications, 100

International characters, 32,40, 110

Italic printing, 20,36 ccl

Justification, 55

IL/

Left margin, 53

Line feed, 48

Line spacing, 4748,99

Locating the printer, 1

/M/

Macro instruction, 64

Maintenance, 95

Manual feed, 67

Margins: bottom, 50 left, 53 right, 54 top, 50

Master print mode, 44

Micro-feed, 27

Microjustification, 44

Most significant bit, 64

/NI

Near letter quality, 20,34,61,63,74-

NLQ Type Style button, 20,23

Off-line, 18,66

On Line button, 18,21,66

Orator type style, 20,36

Overlining, 38

Page feed, 5 1

Page length, 30,50

Page width, 99

Panel pitch, 22

Panel style, 23

Paper Feed button, 19,22,26,27

Paper feed, 100

Paper feeding, 92

Paper guide, 8,15

Paper specifications, 100

Paper-out detector, 3 1,5 1

Parking, 15

Pause, 18

Pica pitch, 19,4 1

Pitch, 19,22,41,99

Platen knob, 3,4

Power supply, 90

Power switch, 3

Printing, 90

Print Pitch button, 19,23

Print head, 96,99

Printer commands, 33,81

Printing gap adjusement, 16

Printing mechanism, 99

Programming, 80-88

Proportional pitch, 19,43

Pull tractor, 13

112

I

Quadruple-size characters, 44

Rear cover, 3,11

Release lever, 3,8, 11

Reset printer, 67

Reverse line feed, 48

Reverse micro-feed, 27

Ribbon cartridge, 4,100

Right margin, 54

ROM character set, 63

Sanserif type style, 20,35

Self tests, 21-22

Set/Eject Park button, 19

Setting up, 4

Single sheets: automatic loading, 8 manual loading, 10 specifications, 100

Slash zero, 4 1

Small capitals, 20

Specifications, 99-102

Sprocket feed, 11-14, 100

Standard character set, 31, 39, 104-

105

Standard mode, 3 1,86

Subscripts, 38

Superscripts, 38

ITI

Tabulation, 52

Test patterns, 21

Top cover, 3,4

Top margin, 50

Top of form, 27

Tractor feed, ll-14,100

Troubleshooting, 89-94

Type style, 20,99

ml

Underlining, 37 ,

Unidirectional printing, 67

Unpacking and inspection, 2

Unparking, 15

m

Vertical position commands, 47-53

Vertical tabulation, 53

Zero (slash and normal), 41

113

COMMAND SUMMARY

PAGE MODE CONTROL CODE FUNCTION

<BEL>

<BS>

<HTs

<LF>

<VT>

<FF>

<CR>

<so>

<SI>

<DCI>

Std. <DC2>

IBM <DC2>

Std. <DC3> cDC4>

<CAN>

Bell

Backspace

Horizontal tab

Line feed

Vertical tab

Fomt feed

Carriage return

Expanded printing for one line

Condensed printing

Set printer on-line

Cancel condensed printing

Pica pitch

Set printer off-line

Cancel one-line expanded printing

Cancel last line

<ESC> <OS

<ESC> <4> cESC> “R”

<ES& “T” n

Reverse line feed

Return to top of current page

Expanded printing for one line

Condensed printing

Manual feed

Auto feed

Eject paper from ASF

Set pnnt start position on ASF

Std. <ESC> <SP> n

<ESC> “!” n

<ESC> “W

<ESC> “$” nl n2

<ESC> “%” “0”

<ESC> “%” “1”

Increase character spacing

Select master print mode

Act t MSB as is

Select ROM character set

Select download character set

Select ROM character set

Select download character set

<ESC> “&” <0> nl n2 m0 ml m2 d

ml 1

Define draft download character

Std.

IBM <ES& “2”

<ESC> “3” n

Std.

IBM

Std.

<ESC> “&” <O> nl n2 m0 ml m2 ml.. .m46

Define NLQ download character

<ESC> “*” n0 nl n2 ml m2

<ESC> I‘-” <(h

Select graphics mode

Execute macro instruction

Define macro instruction

Stop underlining

<ESC> ‘I-”

<ESC> “-‘I “I-J’

<ESC> “-” “1”

<ESC> “p’ n0

<ESC> “0”

<ESC> “1”

<ES& “2”

<ESC> “4”

<ESC> “4”

<ESC> “5”

Start underlining

Stop underlining

Start underlining

Select vertical tab channel

Set line spacing to l/8 inch

Set line snacine to 7fl2 inch

Set line spa& to l/6 inch

Execute <ES& “A”

Set line spacing to nn16 inch

Select italic characters

Set top of page at current position

Select upright characters

114

MODE CONTROL CODE

FUNCTION

PAGE

Std.

IBM

Std.

IBM

Std.

IBM <ESC> “5” <l>

IBM <ESC> “5” <o,

<ESC> “6”

<ESC> “7”

Set automatic line feed

Cancel automatic line feed

Select character set #2

Select character set #l z;

IBM

<ESC> “8”

<ESC> “9”

<ESC> “:‘*

Disable paper-out detector

Enable paper-out detector

Elite pitch

Std.

<ES0 “<”

Std.

<ESC> “=*’

Copy standard characters from ROM into RAM

One-line unidirectional

Set MSB to 0

IBM <ESC7 ‘k” nl n2 <DC4> a0 al a2 ml m2

ml1

printing

Define download characters

Set MSB to 1 <ESC> “>”

<ESCs “?” n m

<ESC> “@”

<ESC> “A” n

Convert graphics density

Reset printer

Set line spacing to n/72 inch

Set vertical tabstops <ESC7 “B” nl n2 . ~07

<ESC7 “c” n

Set page length to n lines

Set page length to n inches

Set horizontal tab stops

Emphasized printing <ESCs “E”

<ESC>

“F”

<ESC7 “G” rnM

<ESC> “II”

<O>

IBM <ESC> “I”

<17

IBlM <ESC> “I” <2>

IBM <ESC> “I”

<37

IBM

<ESCs “I”

<47

<ESC7 “I” <57

<ESC> “I” <67

<ESC> “I”

<77

&SC> “I” “0”

<ESC> “I” “1”

<ESC> “I” “2”

<ESC> “I” “3”

<E‘J-> “I” “4”

Cancel emphasized printing

Double-strike printing

Cancel double-strike printing

Select draft aualitv characters

Select draft ilite characters

Select Sanserif characters

Select Courier characters

Select draft download character set

Select draft elite download character set

Select NLQ download character set

Select Courier characters

Select draft quality characters

Select draft elite characters

Select Sanserif characters

Select Courier characters

Select draft download character set

<ESC> “I” “5”

<ESC> “I” “6”

&SC- “I” “7”

Select draft elite download character set

Select NLQ download character set

Select Courier characters

Perform one n/216-inch line feed

Print normal-density g-bit graphics

Print double-density g-bit aranhics cESC7 “J” n

<ESCs “K” nl n2 ml m2

<ESC7 “L”

n2 ml m2

<ESC> “M”

<ESC7 “N” n

<ESC7 “0”

<ESC> “p”

<ESC> “P’

<17

<ESC7 “Q” n

<ESC> “Q”

<SYN7

<ESC7

“R”

<ESC7

“R” R

<ESC>

“s” <07

<ESC>

“s”

<l>

<ESC> “S” “0”

<E-g-> “S” “1”

<ESC7

“T’

<ESC>

“U”

<o>

<ESC> “U” <l>

<ESC- “u” “0”

Elite pitch

Set bottom margin

Cancel top and bottom margins

Pica pitch

Select fixed spacing

Select proportional

Set right margin

Set printer off-line

Reset all tab stops

Select international

Superscript

Subscript

Superscript

Subscript

- spacing

- - character set

Cancel superscript or subscript

;y.i;;;;~;~~;;;g

Bidirectional printing

115

MODE CONTROL CODE

FUNCTION PAGE

<ESC> ““” “1”

<ESC> “W” <17

<ESC> “w” “0”

<ESC- “w” “1”

Unidirectional printing

Cancel expanded printing

Expanded printing

Cancel expanded printing

Expanded printing

<ESC7 “x” nl n2

<ESC7 “Y” nl n2 ml m2 .

Std.

<ESC7 “[” “@” <47 -co> <07 <07 n m

<ESC7 ‘T’ nl n2

Select character height, width, and line spacing

Relative horizontal Lb

IBM <ESCs ‘9” nl n2

Enable printing of all character codes

IBM <ES& “*”

Enable printing of all character codes on next

Std.

<ES& “z” nl n2 ml m2 . . .

<ESC7 “A” n0 nl n2 ml m2 . .

Print quadruple-density g-bit graphics character

Print 9-pin graphics

Stop ov&niig

Start overlining

<ESC> ‘I-‘* <17

<ESC> .G?’ “1”

<ESC> “ ” “1”

Stop overlining

Start overlining

Set left and right margins 54

Print double-density, double-speed g-bit graphics 58

<ESC7 “a” ~17

<ESC7 “a” ~27

<ESC> “a” “0”

<ESC7 “a” “1”

<ESC7 “a” “2”

<ESC7 “b” n0 nl n2

<ESC7 “co n

<ESC7 “e” co7 n

Left justify

Center text

Right justify

Left justify

Center text

Right justify

Set vertical tab stops in channel

Set top margin

<ESC7 “e” ~17 n

<ESC7 “e” “0” n

<ESC7 “e” “ 1” n

<ESC7 “f’ ~07 n

<ESC7 “f’ ~17 n

<ESC7 “f’ “0” n

4SC7

<ESC7 “h” n

<ESC> “i” “0”

<ESC> ‘Ii” “1”

&SC7

“f’ “1” n

“j” n

<ESC7 “k”n

<ESC> “1” n

<ESC> “p” “0”

. . .

<o>

Set horizontal tab stop every n columns

Set vertical tab stops every n lines

Set horizontal tab stop every n columns

Set vertical tab stops every n lines

Absolute horizontal tab in columns

Feed paper n lines

Absolute horizontal tab in columns

Feed paper n lines

Select double or quadruple size

Cancel immediate print

Immediate print

Cancel immediate print

Immediate print

Perform one nf216-inch reverse lie feed

Select NLQ type style

Set left margin

Select fixed spacing

Select proportional spacing

Select fixed spacing

<ESC> “p” ” 1”

<ESC> “t” <17

<ESC> “1” “0”

<ESC- “t”” 1”

<ESC> “w” <Is

<ESC> “w” “0”

<ESC> “w” “1”

<ESC> “x” <17

<ES& ‘ax” “0”

<ESC> ‘4x” “1”

Select proportional spacing

Select standard character set

Select IBM character set

Select standard character set

Select IBM character set

Return to normal height

Print double-height characters

Return to normal height

Print double-height characters

Select draft quality characters

Select NLQ characters

Select draft quality characters

Select NLQ characters

Select normal zero

Select slash zero

116

MODE CONTROL CODE

<ESC> ‘L” “0”

<ESC> ‘a-” “ 1”

IBM <FS> “4”

IBM cFS> “5”

IBM <FS> “:” <o> <O> <o>

IBM <FS> “=”

IBM <FS> “Q” n

IBM <FS> “R” n

IBM <FS> ‘T’ nl n2

“(” “(” ‘L-0 “)” “)” “o”

“(” “(” ‘L-0 “)” “)” “l”

“(” “(” “0” “)” “)”

“(” “(” ‘a4” “)” “)”

“(” “(3. “B” “)” “)” “0”

“(” “(” “B” “)” “)” “1”

“(” “(” “F” “)” “)” “0”

“(” “(” “F” “)” “)” “1”

“(” “(I, “F” “)” u)” “2”

“(” “(” “F” “)” “)” “3”

“(” “(” “F” “)” u)” “y

“(” “(” “I” “)” C‘)” “0”

“(.I “(” “I” “)” “)” “1”

“(” “(” “R” “)” “)”

“(” “(” “S” “)” “)” n

FUNCTION PAGE

Select normal zero

Select slash zero

Select italic characters

Select upright characters

41 i:,

Copy standard characters from ROM into RAM 60

Set MSB to 0

Set right margin

Select international character set

Relative horizontal tab

Stop underlining i!:

Start underlining

Manual feed

Auto feed

Cancel double-strike printing

Double-strike printing

Select Courier characters

Select Sanserif characters

Select Orator characters with small capitals

Select Orator characters with lower case

Sclcct draft quality characters

Select upright characters

Select italic characters

Eject paper from ASF

Select character size

2 ii

3.5

117

Witaj! Jestem chatbotem AI specjalnie przeszkolonym, aby pomóc Ci w obsłudze Star Micronics NX 1500 printer User's Manual. Dokładnie przejrzałem dokument i mogę pomóc Ci zlokalizować dokładne informacje, których potrzebujesz, lub wyjaśnić treść w jasny i prosty sposób. Niezależnie od tego, czy szukasz wskazówek dotyczących konkretnych funkcji, kroków rozwiązywania problemów, czy ogólnego użytkowania, możesz zadawać pytania. Im więcej szczegółów podasz na temat swoich obaw lub potrzeb, tym dokładniej i skuteczniej mogę Ci pomóc!

Asystent pisze

Asystent jest niedostępny. Spróbuj ponownie później.

Wygląda na to, że dotarłeś do dokumentu napisanego w wielu językach, w tym w języku, który nie jest Twoim językiem ojczystym. Możesz użyć poniższych linków, aby tymczasowo ukryć strony bez preferowanego języka.

Reklama

MULTI-FONT

HOW TO USE THIS MANUAL

FEATURES OF THE PRINTER

TABLE OF CONTENTS

r

Chapter I

LOCATING THE PRINTER

UNPACKING AND INSPECTION

Check the carton contents

Parts name of the printer

SETTING UP

Mount the platen knob

Install the ribbon cartridge

Connection

LOADING SINGLE SHEETS

Automatic loading

Manual loading

LOADING AND PARKING FANFOLD FORMS

Loading the paper from the rear of the printer

Loading the paper from the bottom of the printer

Paper parking

Paper unparking

ADJUSTING THE PRINTING GAP

Chapter 2

CONTROL PANEL OPERATIONS

BUTTONS AND INDICATORS

ON LINE button

I

PAPER FEED button

SET/EJECT PARK button

PRINT PITCH button

q

NLQ TYPE STYLE button

POWER-UP FUNCTIONS

Long test mode

Print area test mode

Stay in panel pitch

Stay in panel style

Stay in panel pitch and style

Hexadecimal dump

SWITCH COMBINATION FUNCTIONS

Top of form

Forward micro-feed

Reverse micro-feed

Clearing the buffer

Chapter 3

D/P SWITCH SETTINGS

LOCATION OF THE DIP SWITCHES

FUNCTIONS OF THE DIP SWITCHES

Chapter 4

PRINTER CONTROL COMMANDS

FONT CONTROL COMMANDS

Select draft quality characters

Select draft elite characters

Select NLQ characters

Select NLQ type style

Select Courier characters

Select Sanserif characters

Select Orator characters with small capitals

Select Orator characters with lower case

Select italic characters

Select upright characters

Emphasized printing

Cancel emphasized printing

Double-s trike printing

Cancel double-strike printing

Start underlining

Stop underlining

Start overlining

Stop 0 verlining

Superscript

Subscript

Cancel superscript or subscript

CHARACTER SET COMMANDS

Select standard character set

Select IBM character set

Select character set #I

Select character set #2

Select international character set

Enable printing of all character codes