Led Spot 200 User Manual

Led Spot 200 User Manual
USER MANUAL
Please read the instruction carefully before use
CONTENTS
1. Safety Instructions .................................................................................................. 2
2. Technical Specifications .......................................................................................... 3
3. How To Control The Unit ........................................................................................ 4
3.1 Control Panel .................................................................................................... 4
3.2 Main Function .................................................................................................. 5
3.3 Home Position Adjust ..................................................................................... 10
4. How To Control The Unit ...................................................................................... 10
4.1 Master/Slave Built In Preprogrammed Function ............................................. 11
4.2 Easy Controller ............................................................................................... 11
4.3 DMX Controller............................................................................................... 12
4.4 DMX 512 Configuration .................................................................................. 13
4.5 DMX512 Connection ...................................................................................... 14
5. Troubleshooting ................................................................................................... 15
6. Cleaning and Maintenance ................................................................................... 16
1A
1. Safety Instructions
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.
WARNING
 Please keep this User Guide for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using the unit.
 Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
 Disconnect main power before replacement or servicing.
 Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
 Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but always by
taking its base.
 Maximum ambient temperature is Ta: 40℃. Don’t operate it where the temperature is higher
than this.
 Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during its
operation. Turn off the power and allow about 15 minutes for the unit to cool down before
replacing or serving.
 In the event of serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center. Always use the same type
spare parts.
 Do not touch any wire during operation as high voltage might be causing electric shock.
Warning
 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
2A
moisture.
 Do not open the unit within five minutes after switching off.
 The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to
which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the
touch of people and has no one pass by or under it
2. Technical Specifications
The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together in
master/slave connection, as many as required and run by built-in program chase sequences
automatically or by sound activation through an internal microphone to create an intelligent
effect.
• It can be operated by DMX 512 control or can be used as an individual unit without a controller.
• Features different preprogrammed chase patterns.
• Please use a cable when connecting units together.
• Accurate focusable optics system and ultra smooth stepping motors, Fan cooled.
• Pan: 540 deg. Tilt: 270 deg.
• Power Voltage:AC 230V~50Hz
• Power Consumption: 60W
• Light source: 1×25W LED
3A
• Dimension: 248x 228 x 329mm
• Weight: 5.1 kg
3. How To Control The Unit
3.1 Control Panel
4A
○,1 Display:
To show the various menus and the selected functions
○,2 LED:
DMX
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
On
Sound Mode
○,3Button:
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
○,4 Fuse (T 2A):
Protect the unit from damage of over current
○,5 Mains input:
Connect to the power supply
○,6 Only for remote control:
Connecting whit CA-8 to control the unit for Stand by, Function and Mode function
○,7 DMX input:
For DMX512 link, use 5-pin XLR plug cable to input DMX signal
○,8 DMX output:
For DMX512 link, use 5-pin XLR plugs cable to link the next unit
○,9 Sensitivity:
Adjust the sensitivity
3.2 Main Function
To select any of the given functions, press the MENU button up to when the required one is
showing on the display. Select the function by ENTER button and the display will blink. Use DOWN
and UP button to change the mode. Once the required mode has been selected, press the ENTER
5A
button to setup or it will automatically return to the main functions without any change after
idling 8 seconds. To go back to the functions without any change press the MENU button. The
main functions are showing below:
6A
DMX 512 Address Setting
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the
address has been selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without any change
press the MENU button again.
Show Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(show 2) or
(show 3) or
(show 1) or
(show 4) mode. Once the mode has been selected, press
the ENTER button to setup or automatically return to the main functions without any change after
8 seconds. To go back to the functions without any change press the MENU button again.
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, the spot is always projecting
to the audience’s direction; i.e. in front of the stage. Pan movement angel (left to right to left):
160°. Tilt movement angel:
90° (60° above horizon; 30° below horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angel (left to right to left):160°.
Tilt movement angel: 90°
(vertically, front 75°; back 15°)
Slave Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(normal) or
(2
light show) mode. Once the mode has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to the
functions without any change press the MENU button again.
7A
Sound Mode
Press the MENU button until the
is showing on the display. Pressing ENTER button and the
display will blink. Use DOWN and UP button to select the
(sound on) or
(sound off)
mode. Once the mode has been selected, press the ENTER button to setup or automatically return
to the main functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Blackout Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(yes blackout) or
(no blackout) mode. Once the mode has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to the
functions without any change press the MENU button again.
Pan Inversion
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(normal) or
(pan
inversion) mode. Once the mode has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to the
functions without any change press the MENU button again.
Tilt Inversion
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(normal) or
(tilt
inversion) mode. Once the mode has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to the
functions without any change press the MENU button again.
8A
Led Display
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(Led on) or
(Led
off) mode. Once the mode has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
when the
is blinking on the display. Use the ENTER button to change to the mode
(display normal), It will automatically store after 8 seconds. Or press the ENTER button again
return to the mode
(display inversion). To go back to the functions press the MENU
button.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
Focus Adjust
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button to
change orientation of the light, then you can turn the plastic lens manually to adjust the focus of
the unit. To go back to the functions press the MENU button again.
Self-Test
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button
and the unit will run self-test by built-in program. To go back to the functions press the MENU
button again.
Temperature Test
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button
9A
and the display will show the temperature of the unit. To go back to the functions press the MENU
button again.
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button
and the display will show the number of working hours of the unit. To go back to the functions press
the MENU button again.
Software version
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button
and the display will show the version of software of the unit. To go back to the functions press the
MENU button again.
Reset
Press the MENU button up to when the
is blinking on the display. Pressing ENTER button
and all channels of the unit will return to their standard position. To go back to the functions
without any change press the MENU button again.
3.3 Home Position Adjust
In the main functions, hold Enter button for at least 3 seconds into offset mode, when the
is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP
button to adjust the home position. Once the position has been selected, press the ENTER button
to setup, hold the MENU button for about 3 seconds or wait for 8 seconds to back to the main
functions without any change.
4. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
10A
3. By universal DMX controller
No need to turn the unit off when you change the DMX address, as new DMX address setting
will be affected at once. Every time you turn the unit on, it will show
on the display and
move all the motors to their ‘home’ position and you may hear some noises for about 20 seconds.
After that the unit will be ready to receive DMX signal or run the built in programs.
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when you want
an instant show. You have to set the first unit in master mode
or
(show 2) or
(show 3) or
and select
(show 1)
(show 4) mode. Its DMX input jack will have
nothing plugged into it, and Its master LED will be constantly on and sound LED will flash to the
music. The other units will have to set in slave mode
and select
(normal) or
(2 light show) mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the
slave led lights will constantly on.
2-light show
In
(slave mode),
means the unit works normally and
order to create a great light show, you can set
means 2-light show. In
on the second unit to get contrast
movement to each other, even if you have two units only.
4.2 Easy Controller
The easy remote control is used only in master/slave mode. By connecting to the 1/4” microphone
jack of the first unit, you will find that the remote control on the first unit will control all the other
units functions press the MENU button again.
11A
Stand By
Blackout the unit
Function
1. Sync. Strobe
Show
1. Press to select color
2. Async strobe
1-4
2. Hold to select gobo
Show
LED ON
3. Sound Strobe
Mode
Sound (LED OFF)
(LED Slow Blinking)
4.3 DMX Controller
A universal DMX controller to control the units, you have to set DMX address from 1 to 512
channel so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the
address has been selected, press and keep ENTER button pressed up to when the display stops
blinking or storing automatically 8 seconds later. To go back to the functions without any change
press the MENU button again. If you use please refer to the following diagram to address your
DMX512 channel for the first 4 units:
12A
4.4 DMX 512 Configuration
13A
4.5 DMX512 Connection
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W
resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the
input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very
high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when
one of the units’ power is disconnected.
5. Each lighting unit needs to have an address set to receive the data sent by the controller. The
address number is between 0-511 (usually 0 & 1 are equal to 1).
14A
6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin 4/Pin 5: Not used.
5. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and DMX
polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the
fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause
damage or interference to DMX interface circuit.
C. Some fixtures don’t respond to the easy controller
1. Check the LED for the response of the master/ slave mode signal.
2. Check if the unit is receiving DMX signal and cut it off.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
15A
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
6. Cleaning and Maintenance
The cleaning must be carried out periodically to optimize light output. Cleaning frequency
depends on the environment in which the fixture operates: moist, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the fixture.

Clean with lint-free cloth using normal glass cleaning liquid.

Clean the surface at least every 30 days.

Never use alcohol or solvents.
16A
17A
Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 2004/108/EC.
EN55103-1: 2009 ; EN55103-2: 2009;
EN61000-3-2: 2006 + A1:2009 + A2:2009; EN61000-3-3: 2008.
&
Harmonized Standard
EN 60598-1:2008 + All:2009; EN 60598-2-17:1989 + A2:1991;
EN 62471:2008; EN 62493: 2010
Safety of household and similar electrical appliances
Part 1: General requirements
18A
Innovation, Quality, Performance
19A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement