AMP03
INSTRUCTION MANUAL
PA Mixing Amplifier
AMP03
1.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
To reduce the risk of electric shock do not remove cover (or back panel). No
user serviceable parts inside. Refer servicing to qualified personnel only.
WARNING:
To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture.
This symbol is intended to alert the user of the presence of uninsulated
dangerous voltage within the product enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user of the presence of important operating
and maintenance (servicing) instruction in the literature accompanying the
appliance. Please carefully read the owner’s manual.
INSTRUCTIONS:
All safety and operating instructions should be read before the product is operated.
Retain these instructions:
All safety and operating instructions should be retained for future reference.
This owner’s manual should be considered as a part of the product and it must accompany it
every time, and delivered to the new user when this product is sold. In this way the new owner will
be aware of all the installations, operating and safety instructions.
Heed all warnings:
All warnings on the product and in owner’s manual should be adhered to.
Heed all warnings.
Follow all instructions:
All operating and user’s instructions must be followed.
Sentences preceded by
symbol contain important safety instruction. Please read it carefully.
DETAILED SAFETY INSTRUCTIONS.
Water and moisture:
This apparatus should not be used near water (i.e. bathtub, kitchen sink, swimming pools,
etc.)
Ventilation:
This apparatus should be placed in a position that doesn’t interfere with correct ventilation.
This unit, for example, should not be placed on a bed, sofa cover o similar surfaces that could
cover ventilation openings, or placed in a built-in installation, such a bookcase or a cabinet
that could block air flow trough ventilation openings.
Heat:
This apparatus should be placed away from heat sources, like radiators, heat registers, stoves
or other products (including amplifiers) that produce heat.
Power sources:
•
This apparatus should be connected only to power source type specified in this owner’s
manual or on the unit.
•
If the supplied AC power cable plug is different from wall socket, please contact an
electrician to change the AC power plug.
Grounding or Polarization:
•
All precautions must be observed in order to avoid grounding or polarization defeating.
•
Unit metal parts are grounded through the AC power cord.
•
If the AC power outlet doesn’t have grounding, consult an electrician for outlet grounding.
Power cord protection:
The power cord should be routed in a way it will not be walked on or pinched by items placed
upon or against it, paying particular attention to cords at plugs, convenience receptacles and
wall outlet.
Cleaning:
•
You can clean the unit with a compressed air flow or a wet cloth.
•
Don’t clean the unit using solvents like trichloroethylene, thinners, alcohol, or other fluids
with very strong volatility and flammability.
Non use periods:
The unit AC power cord should be unplugged from the outlet if it’s unused for a long period.
Objects or liquid entry inside the unit:
Be careful that no objects fall or liquid is spilled inside the unit through ventilation openings.
Safe power line use:
•
Keep firmly the plug and the wall outlet while disconnecting the unit from AC power.
•
When the unit will not be used for a long period of time, please unplug the power cord
from AC power outlet.
•
To avoid unit power cord damaging, please don’t strain the AC power cable and don’t
bundle it.
•
To avoid unit power cord damaging, please be sure that the power cord is not walked on
or pinched by heavy objects.
Unit relocation:
Before any unit relocation please control the unit is turned off. Power cord must be unplugged
by the wall outlet, and all the connections wires should be disconnected as well.
Don’t open this unit:
Don’t attempt to open or to repair by yourself this unit. For any problem solution not described
in this owner’s manual, please refer to qualified personnel only or consult us or your National
Distributor. Any improper operation could result in fire or electric shock.
Damages requiring services:
•
Don’t attempt to do operations not described in this user’s manual.
•
In the following cases please refer to an authorized maintenance center or skilled
personnel:
- When the unit works improperly or it doesn’t work at all.
- If power cord or plug are damaged.
- If liquid has spilled, or objects have fallen into the unit.
- The unit has been exposed to rain.
- The unit doesn’t operate normally or it exhibits a marked change in performance.
- If the product has dropped or it has been damaged in any way.
Maintenance:
The user shouldn’t attempt maintenance operation not described in this user’s manual. Every
maintenance operation should be done by qualified personnel only.
IMPORTANT SAFETY INSTRUCTIONS:
•
Install this unit following owner’s manual instructions.
•
Don’t install, connect or disconnect power supply when the unit is powered, otherwise
there’s an high risk of electric shock.
•
Don’t open the unit, there are no user serviceable parts inside.
•
If you detect a particular smell from the unit, please immediately turn it off and disconnect
the AC power cord.
•
Don’t block the unit ventilation openings.
•
Avoid to use this unit in overload for a long period.
•
Don’t force commands (switches, controls, etc.)
•
To obtain good speakers wire contacts, please tighten the screw terminals firmly.
•
For safety reason, don’t defeat the grounding connection. Grounding is useful for user
safety.
Use only connectors and accessories suggested by the manufacturer. .
This unit should be placed in a rack (see INSTALLATION) and kept far from:
Wet places
Direct exposure to heat sources (like sun light)
Non properly ventilated places
Disconnect the power cord during storms or when the unit is not used.
•
•
•
•
•
In order to prevent fire and electric shock risks, it’s necessary to keep the unit far
from sprinkling and drops. Please don’t put cups, vases or other object containing liquids
over the unit. In case of interferences from source signal, THD value will raise over 10%.
Don’t place this unit in a bookshelf o in other places with small room.
PROEL S.P.A. is not responsible for any damage that occurs due to a wrong unit
installation.
Thank you for choosing one of Proel products, and for your confidence towards
our brand, synonymous of professionalism, accuracy, high quality and reliability.
All our products are CE approved and designed for continuous use in
professional installation systems.
1. DESCRIPTION
This unit is designed for speech, music, paging and sound reinforcement
applications.
FEATURES
• Two MIC inputs.
• One PHONO input and one AUX input switch selectable.
• LED power indicator.
• Master output level.
• PHONO and AUX level controls.
• MIC1 level control.
• MIC2 level control.
• Bass, Middle and Treble tone controls.
• Grounding terminal.
• Four outputs – three constant impedance outputs (4Ω, 8Ω, and
16Ω) – one constant voltage output (100 V).
• Priority function.
2. FRONT PANEL DESCRIPTION
fig.1
1) Power On/Off switch.
2) MASTER output volume control.
3) High frequency tone control (6 KHz).
4) Middle frequency tone control (1 KHz).
5) Low frequency tone control (150 Hz).
6) PHONO/AUX volume control.
7) MIC2 volume control.
8) MIC1 volume control.
4. REAR PANEL DESCRIPTION
fig.2
1) Fuse-holder.
2) AC power cord (220 V AC).
3) Priority function terminals.
4) Speakers output terminals (4Ω, 8Ω, 16Ω, 100 V).
5) AUX or PHONO switch.
6) MIC2 1/4" jack input.
7) MIC1 1/4" jack input.
8) PHONO input (RCA connectors).
9) AUX/CD input (RCA connectors).
10)Grounding terminal.
5. INSTALLATION
1. Input connections
• MICROPHONE CONNECTION:
Please always use a shielded cable to connect every kind of
microphone. To obtain a good sound quality, we suggest to use
microphones cables up to 10-20 meters (32-64 feet). This value is
strictly correlated to microphones specifications.
Microphones inputs are unbalanced. We suggest to use unbalanced
low impedance microphones (30 – 600Ω ).
Unbalanced wiring of a balanced low impedance microphone:
Unbalanced low impedance microphone wiring:
• AUX /PHONE
CD players, cassette decks, tuners, mixers and other external line level
output equipment may be connected to AUX input.
The selector switch allows to choose input signal AUX and PHONO.
Note: AUX and PHONO cannot be used simultaneously.
2. Output connections
Attention
To prevent the risk of electric shock, never touch amplifier outputs
when the amplifier is turned on.
To access to speaker connection terminals (fig. 2 ref. 4) remove the
protection cover unscrewing the screws.
This amplifier may be used both with constant impedance speakers (4,
8, and 16 Ω) and with constant voltage speakers (100V).
CONSTANT IMPEDANCE LINE.
To use this amplifier with a constant impedance line, please connect
the COM terminal to the negative post of your speaker, and connect
the positive terminal to desired positive post (4, 8, 16Ω) (fig. 2 ref.
4).
• To obtain the best performances, the total speakers impedance
connected to the line, should be equal to the amplifier output
impedance.
•
•
Speakers power sum should not be lower than the amplifier
output power.
We suggest you to don’t use long cables. Anyhow, for longer
distances application use a thicker cable.
CONSTANT VOLTAGE LINE.
If you’re using a constant voltage line, connect either the 100V to the “+”
side of speaker system, and connect COM to “-“ side of the speaker
(fig. 2 ref. 4).
• Speakers should have a transformer of the same voltage
developed by the amplifier.
• Speakers power sum should not be higher than the amplifier
maximum output power.
3. Priority Function
When PRIORITY (fig.2 rif.3) terminals are in short-circuit, MIC2, AUX
and PHONO inputs are muted and MIC1 has output priority.
6. OPERATIONS:
a. Pressing the POWER switch the unit turns on, and its LED is lit.
Pressing it again the unit turns off.
b. BASS (150Hz) control modifies signal lower frequencies output (up to
10 dB of boost or cut). Set this control level by personal taste and
ambient acoustic character.
c. MIDDLE (1kHz) control modifies signal lower frequencies output (up to
10 dB of boost or cut). Set this control level by personal taste and
ambient acoustic character.
d. HIGH (6kHz) control modifies signal lower frequencies output (up to 10
dB of boost or cut). Set this control level by personal taste and ambient
acoustic character.
e. MIC 1, MIC 2 and AUX/PHONO inputs have their own independent
volume control. These controls allows to set their level in order to listen
to each program source at the desired level.
f. Turning clockwise the MASTER volume control, the playback level will
raise, turning it counter clockwise it will be lower.
7. Technical specifications
Model
Output RMS / MAX power
Constant voltage output
Constant impedance outputs
AMP03
30 W / 60 W
100V
4Ω, 8Ω, 16Ω
MIC1, MIC2: 30 - 600Ω Unbalanced ¼” jack
Inputs connectors
AUX /PHONE: 10 KΩ RCA
4Ω, 8Ω, 16Ω on terminal board
Output connectors
100V on terminal board
Frequency response
100Hz – 18KHz
Harmonic distortion
< 1%
Signal to noise ratio (@ 1 KHz) > 55 dB
MIC1, MIC2: -55dB ± 2 dB
Inputs sensitivity
AUX : -20dB ± 2 dB
PHONE: -55dB ± 2 dB
AC power
220 V A.C.
Dimensions (W x H x D)
320 x 190 x 80 mm. – 12.6 x 7.4 x 3.2 in.
Weight
5Kg – 11 lbs.
The product is in compliance with Directive 89/336/EEC (Electromagnetic Compatibility)
and following modifications 92/31/EEC and 93/68/EEC, as the following standards:
EN 50082-1:1997, EN 55013:1990, EN 55020:1994
it is also in compliance with Directive 73/23/EEC (Low Voltage)
and following modifications 93/68/EEC, as the following standard:
EN 60065:1998
Proel SpA pursue a policy of continuous research and development. Proel SpA reserve the right to modify
product circuitry and appearance at any moment, without prior notice.
PROEL S.p.A.
(World Headquarters - Factory)
Via alla Ruenia 37/43
64027 Sant’Omero (Te) – Italy
Tel: +39 0861 811241
Fax: +39 0861 887862
E-mail: [email protected]
installation.proelgroup.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement