Model : PUMA/B - Fuji Electric
-- In cases where damage or problems with this equipment may lead to serious
accidents, install appropriate external protective circuits.
-- To prevent damage and failure of the equipment, provide the rated power voltage.
-- To prevent electric shock and equipment failure, do not turn the power ON until all
wiring is complete.
-- Before turning the power ON, confirm that clearance space has been secured to
prevent shock or fire.
-- Do not touch the terminal while the machine is ON. Doing so risks shock or
equipment errors.
-- Never disassemble, convert, modify or repair this equipment. Doing so risks abnormal
operation, shock or fire.
Instruction Manual (Installation)
Multi-loop module type Temperature Controller
Control Module
Model : PUMA/B
INP-TN1PUMAa-E
1-2
Thank you for purchasing the Fuji module type temperature controller.
Once you have confirmed that this is the product you ordered, please use it in
accordance with the following instructions.
For detailed information on operating this equipment, please refer to the separate
user's manual.
In addition, please keep this instruction manual within easy reach of the actual person
using this equipment.
-- When installing or removing the equipment, turn the power OFF. Otherwise, shock,
operational errors or failures may be caused.
-- Periodic maintenance is recommended for continuous and safe use of this
equipment.
-- Some parts installed on this equipment have a limited life and/or may deteriorate with
age.
-- The warranty period for this unit (including accessories) is one year, if the product is
used properly.
CAUTION
The contents of this manual are subject to change without notice.
This manual is complied with possible care for the purpose of accuracy, however,
Fuji Electric shall not be held liable for any damages, including indirect damage,
caused by typographical errors,
absence of information or use of information in this manual.
Confirming Specifications and Accessories
Before using the product, confirm that it
matches the type ordered.
(For model code, please refer to page 4.)
Confirm that all of the following
accessories are included.
Temperature Controller Control Module 1 Unit
Instruction Manual
1 copy
I/V unit (250 ohm resistance)
1 unit per voltage/current input
Related Information
Material
name
Specification Catalog
Operating
Control
instruction
module
User's
manual
Tool
PUM
parameter
loader
Material No.
ECNO 1162
INPTN5A0198-E
INPTN5A0201-E
Please Read First (Safety Warnings)
Improper use of the equipment may result in death or serious injuries.
Warning
Improper use of the equipment may cause injury to the user or property
damage.
1
Warning
1-1
Installation and Wiring
-10 to 50 degree C
Ambient humidity
90% RH or below (with no condensation)
Vibration
10 to 70Hz less than 9.8m/s² (1G)
Warm-up time
30 min. or more
Installation category
IEC1010-1: class II
Pollution level
IEC1010-1: degree 2
Creepage Space [mm]
0.2
1.2
0.2
1.4
0.5
1.6
1.5
3.0
Please consult our distributor
• For the above, if voltage exceeds 50Vdc (called danger voltage), basic insulation is
required between the earth and all terminals of the equipment.
Note that the insulation class for this equipment is as follows. Before installing,
please confirm that the insulation class for the equipment meets usage requirements.
Power
PV1 Input
Loader communication port
RS-485 communication port
CT Input (CT1A, B - CT4A,B)
PV2 Input
2-4
PV4 Input
OUT1 (SSR drive, current)
OUT2 (relay contact output)
OUT2 (SSR drive, current)
OUT3 (relay contact output)
OUT3 (SSR drive, current)
OUT4 (relay contact output)
OUT4 (SSR drive, current)
Cautions for Wiring
Error Operation
-- The alarm function does not work properly when an error occurs unless the settings
are made correctly. Always verify its setting before operation.
-- In case of error input, PWR LED will flash. When replacing the sensor, make sure to
turn the power OFF.
PV3 Input
OUT1 (relay contact output)
Cautions when Mounting to Cabinets / DIN rails
-- For thermocouple input, use the designated compensation lead. For resistance bulb
input, use wires with small lead wire resistance and without any resistance difference
among three wires.
-- To avoid the influence of inductive noise, input signal wires should be separated from
electric power lines or load lines.
-- Input signal wire and output signal wire should be separated from each other. And
both should be shielded.
-- If the output operation frequency is high, selecting a SSR/SSC drive output type is
recommended.
[Proportionate cycles] Relay output: 30 sec. or more, SSR/SSC drive output: 1sec.
or more
-- When inductive loads such as magnetic opening/closing equipment, etc. as relay
output equipment are connected, use of "Z-trap," manufactured by Fuji Electric
Device Technology Co., Ltd., is recommended in order to protect the contacts against
opening/closing surges and to ensure long-term use.
Model names :ENE241D-07A (For 100V power
21
11
voltage)
22
12
: ENE471D-07A (For 200V power
23
13
voltage)
24
14
Attachment position:Please connect between the
25
15
relay control output contacts.
26
16
-- To comply with CE marking (EMC), we recommend to
27
17
attach ferrite core to communication cable and power
28
18
cable.
29
19
-- For wiring to the terminal block, apply crimp type
30
20
terminals size M3.
Screw size
:M3 x 7 (with square washer)
Z-trap connecting diagram
Screw tightening torque:0.78N-m (8kgf-cm)
• Between the temperature sensor and the location where the voltage reaches or
generates the values described below, secure clearance space and creepage
distance as shown in the table below.
If such space cannot be secured, the EN61010 safety compliance may become
invalid
Basic insulation (1500Vac)
Functional insulation (1000Vac)
Functional insulation (500Vac)
Cautions when Installing
2-3
Ambient temperature
Clearance Space [mm]
2-1
-- In case of mounting the temperature controllers to DIN rails, remember to push up
the locking tabs to fasten the controllers onto DIN rail.
-- To connect controllers, first release all locking tabs. Then, connect controllers and
push up all locking tabs. Make sure that all locking tabs are fastened.
-- Never fail to turn the power OFF, before detaching the terminal block or removing the
main unit from the base part.
-- In order to aid heat dissipation, do not block the top and the bottom of the equipment.
-- When mounting / dismounting controllers to / from DIN rails, 30mm of clearance
above and under the controllers should be provided.
-- Use terminal screws in this product only.
• This equipment is intended to be used under the following conditions.
Voltage used or generated
by any assemblies
Up to 50 Vrms or Vdc
Up to 100 Vrms or Vdc
Up to 150 Vrms or Vdc
Up to 300 Vrms or Vdc
Above 300 Vrms or Vdc
Caution
2-2
Please read this section thoroughly before using and observe the mentioned safety
warnings fully.
Safety warnings are categorized as "Warning" or "Caution".
Caution
2
Please avoid installing in the following locations.
-- Locations in which the ambient temperature falls outside the range of 0 to 50 degrees
C when equipment is in use.
-- Locations in which the ambient humidity falls outside the range of 45 to 85% RH
when equipment is in use.
-- Locations with rapid temperature changes, leading to dew condensation
-- Locations with corrosive gases (especially sulfide gas, ammonia, etc.) or flammable
gases.
-- Locations with vibration or shock directly.
-- Locations in contact with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, there is a risk of electric shock or fire, so have it
inspected by Fuji distributor.)
-- Locations with high concentrations of atmospheric dust, salt or iron particles.
-- Locations with large inductive interference, resulting in static electricity, magnetic
fields or noise.
-- Locations in direct sunlight.
-- Locations that build up heat from radiant heat sources, etc.
Refer to "Module Type Temperature
Controller Control Module User's Manual"
for details about the items described in
this manual.
Content
Maintenance
-1-
Mounting
Others
-- Please do not wipe the equipment with organic solvents such as alcohol or benzene,
etc. If wiping is necessary, use a neutral cleaning agent.
-- Do not use mobile phones near this equipment (within 50cm). Otherwise a
malfunction may result.
-- Malfunctions may occur if the equipment is used near a radio, TV, or wireless device.
-- This equipment requires approx. 20 seconds before it starts to output.
-- Before installing and wiring, take necessary measures for electrostatic discharge
(ESD).
--Dimensions
Front screw terminal cover
(optional)
Terminal block
(when detached from the main unit)
30
Part names and Functions
Mounting screw hole
345
Module connector
(Connect controllers
laterally)
(8)
Module connector
Mounting screw hole
See [Mounting]
When locking tab is released
(when mounting /
dismounting to / from DIN rails)
RS-485 terminal block
See [Wiring]
Locking tab
Operational condition
Illuminated
green
Normal operation
(Slave station of internal communication)
Blinking
green
Normal operation
(Master station of internal communication)
Illuminated
red
System fault
(A/D converter error, internal communication
error)
Blinking
red
Input error
Illuminated
green
RS-485 receiving
Illuminated
orange RS-485 transmitting
30 or more
Color
Illuminated
green
Corresponding channel outputting
Illuminated
red
Corresponding channel input error
[mm]
--Mounting to DIN rails
-- Actions to be displayed for COM and OUT1 -4 can be allocated by programming.
1. Pull down the locking tab of the
base part. Hook the back of the
controller onto the upper part of
DIN rail.
2. Push the controller in the
direction of arrow 2.
Setting
--Setting Station No.
Hook the back
of controller
DIN rail
Set Station No. of each controller before mounting.
Apply a fine tip flat-head screwdriver to turn the Station No. configuration switch.
9
10
A
11
B
12
C
13
D
14
E
15
F
16
OUT3
OUT4
STATION
345
Station No.
Configuration switch
--Attaching end plates
When mounting controllers to DIN rails, we recommend to attach side connecting
terminal covers (right and left 1set), then end plates (optional) to the ends of the
rightmost and leftmost controllers.
-- Each of connected controllers must have a different Station No. from other
controllers. Duplicate Station No. may cause malfunction of the equipment.
DIN rail mounting
end plate
PWR
PUM-A
PWR
LOADER
COM
COM
OUT1
OUT2
PUM-E
PWR
LOADER
COM
STATION
PUM-E
PWR
LOADER
COM
STATION
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
PUM-E
PWR
LOADER
COM
STATION
345
Side connecting terminal cover
(right & left 1 set)
-2-
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
PUM-E
LOADER
STATION
345
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
345
7 8 9A
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
345
6
Do1
Do2
Do3
Do4
Do5
Do6
Do7
Do8
7 8 9A
Di1
Di2
Di3
Di4
Di5
Di6
Di7
Di8
6
345
7 8 9A
OUT4
STATION
6
OUT3
F012
9
F012
8
OUT2
E
8
LOADER
OUT1
F012
7
COM
3. Push up the locking tab to fasten
the controller onto DIN rail.
-- When connecting controllers after
mounting to DIN rail, push up the
locking tab after doing so.
E
7
789A
6
6
PUM-A
6
5
PWR
F012
5
E
4
Locking tab
F012
4
E
3
3
BCD
2
2
BCD
1
1
BCD
Station No.
0
BCD
Rotary SW setting
E
OUT1 - 4
LED Status
F012
COM
[mm]
30 or more
PWR
Main unit
(when detached from the base part)
Cautions when mounting
In order to aid heat dissipation, 30mm of clearance (50mm recommended) above and
under the controllers should be provided.
LED indicator
Six LED lamps indicate the following operational conditions.
LED
Terminal
Screw size M3
E
BCD
Power terminal block
See [Wiring]
Input/output
terminal block
See [Wiring]
DIN rail
Terminal
Screw size M3
6.1
Station No.
Configuration switch
See [Setting]
5
E
7 8 9A
F012
STATION
6
OUT4
Loader communication port
6
50
1.5
OUT4
(30)
LOADER
COM
OUT3
STATION
OUT3
100
PUM-A
PWR
OUT2
LOADER
COM
OUT2
--Base part
OUT1
PUM-A
PWR
OUT1
CT connector
See [Wiring]
LED indicator
Base part
(when detached from
the main unit)
85
BCD
--Main unit
(10)
BCD
2-5
DIN rail mounting
end plate
Wiring
--Fixing with screws
When mounting controllers inside a cabinet with screws, connect the base parts of
controllers first.
-- Fixing screws are not included. Please prepare screws as required.
1. Refer to the figure below for the mounting screw hole
(30)
size to decide the mounting position.
2-M3
--Front terminal block (1ch type / 2ch)
9±0.2
LOADER
OUT1
OUT2
STATION
F012
E
BCD
21
11
22
12
3. Connect base parts. Push up to fasten all the locking tabs.
23
13
4. Fixate the base parts onto the mounting position inside the cabinet with screws.
5. Attach the main unit to the base parts.
24
14
25
15
26
16
27
17
28
18
29
19
30
20
+0.2
30+0.7
(3)
2. Remove the main unit from the base part.
See [How to detach the base part]
[mm]
--Connecting controllers
PWR
LOADER
F012
F012
E
12
12
Voltage/Current
input*
13
14
14
14
15
15
15
Relay contact
output
Current
output
SSR drive
output
16
16
16
17
17
17
Thermocouple Resistance
input
bulb input
18
18
Voltage/Current
input*
18
19
19
19
20
20
20
*In case of currenet input, attach I/V unit which comes with the controller to the voltage input terminal.
345
7 8 9A
OUT4
12
LOADER
STAT ION
6
OUT3
7 8 9A
BCD
OUT4
OUT2
345
11
CH2
PUM-A
COM
OUT1
STATION
6
OUT3
2. Connect controllers with each other using
side connectors.
PUM-A
COM
OUT2
E
PWR
OUT1
BCD
1. Check that locking tabs are pulled down
(released).
11
Thermocouple Resistance
input
bulb input
13
13
7 8 9A
OUT4
345
6
OUT3
11
Process value
input 1
PUM-A
COM
Control output 2
PWR
Current
output
SSR drive
output
Process value
input 2
(100)
88.5 ±0.2
Relay contact
output
Control output 1
CH1
--Front terminal block (3ch, 4ch)
PUM-A
PWR
PUM-A
COM
LOADER
COM
LOADER
OUT4
OUT1
STAT ION
2
3456
OUT2
OUT3
OUT4
Control output 3
OUT3
F01
A
F01
OUT2
BCDE
3456
STAT ION
2
3456
789
2
F01
OUT1
STATION
789
BCDE
OUT4
A
OUT3
BCDE
OUT2
A
OUT1
4. All connected controllers are connected
to power supply and RS-485 via side
connectors if one of controllers is directly
connected to them.
22
23
23
23
SSR drive
output
24
Current
output
24
25
OUT2
OUT4
25
Control output 4
Process value
input 4
CH4
How to detach the base part
1. Press the lock lever on the top of the
main unit.
Lock lever
2. Pull down the upper part of main unit.
Voltage/Current
input*
26
Resistance
bulb input
26
STATION
OUT3
Relay contact
output
24
25
LOADER
F012
22
PUM-A
COM
Thermocouple
input
26
345
E
PWR
LOADER
22
PWR
OUT1
7 8 9A
PUM-A
COM
Thermocouple
input
21
6
PWR
789
21
11
22
12
23
13
24
14
25
15
26
16
27
27
27
27
17
28
28
28
28
18
29
19
30
20
SSR drive
output
Current
output
29
29
30
Relay contact
output
29
30
30
*In case of currenet input, attach I/V unit which comes with the controller to the voltage input terminal.
3. Detach the cutout on the lower end of
back of main unit from the projection
on the base part.
--Base part (power terminal, RS-485 terminal)
-- When attaching the main unit to the
base part, take the reverse procedure
to removing the main unit from the
base part.
-- Make sure that the lock lever of the
main unit is fitted into the base part.
Power terminal
RS-485 terminal
DC 24V (-)
B (-)
DC 24V (+)
A (+)
All connected controllers are connected to power supply and RS-485 via side connectors
if one of controllers is directly connected to them.
--CT input terminal
CN1
Main unit
PWR
PUM-A
COM
LOADER
CN2
Terminal
layout
OUT1
OUT3
STATION
2
3456
789
OUT4
F01
OUT2
BCDE
Projection
Terminal
layout
A
3. After mounting controllers onto DIN rail,
make sure to push up all locking tabs.
Controllers are fastened to DIN rail and to
each other.
Locking tab
Resistance
bulb input
21
BCD
Side
connector
Process value
input 3
CH3
Voltage/Current
input*
21
*Pin No. 2,4, 6,8 of CN1 and CN2 are connected inside the equipment.
*CN2 cannot be used for PUMB.
-3-
SG
Specification
Crimp terminal size
Please prepare power cables and crimp terminals of the size indicated below.
Power cable
General Specification
Cable type
Size
Thermocouple (Compensation lead wire)
Power supply
1.25mm2 or less
1.25mm2 or less
Crimp terminal
Screw tightening torque
0.8Nm
Process value input
No. of input
: 2 or 4 points (1point/channel)
Input signal
: Thermocouple K, J, T, E, R, B, S, N, PL-II
Resistance bulb Pt100, JPt100
DC voltage or DC current
: 0 to 5Vdc, 0 to 10Vdc, 2 to 10Vdc,
0 to 20mAdc, 4 to 20mAdc
Input impedance
: Thermocouple input, voltage input : 1M ohm or more
- Voltage input (V)
: Approx. 1M ohm
- Current input
: 250 ohm
Signal source resistance - Thermocouple
: 0.3%FS ± 1 digit per 100 ohm
- Voltage input (V)
: 0.3%FS ± 1 digit per 500 ohm
Allowable wiring resistance- Resistance bulb input
: 10 ohm or less per wire
Ring crimp terminal
Y crimp terminal
Model code
Control module (4ch)
1
2
3
4
5
6
7
P U M
8
9 10 11 12 13
1 - 0
0 0
A
T
A
Heater break detector (CT) input
No. of input
: 4 or 8 points (2 points/control channel)
Input type
: Single-phase type CT/point
1 to 30A : CTL-6-S-H
20 to 50A : CTL-12-S36-8
Connection method
: Special connector for Heater break detector (optional)
C
A
C
E
Control output
A
C
E
No. of output
: 2 points (1 point/control channel) or 4 points (2 points/control channel)
Control output behavior : Heat (reverse action) or Cool (direct action)
or Heat/cool (control output 2points/control channel required)
Output type
a)Relay contact output
- Proportion cycle
: 1 to 150 sec.
- Contact structure
: SPST contact
- Contact capacity
: 220Vac / 30Vdc, 3A (resistance load)
220Vac / 30Vdc, 1A (inductive load)
- Minimum switching current
: 100mA (24Vdc)
- Mechanical life
: 20,000,000 switching
or more (100/min.)
- Electric life
: 100,000 switching
or more (rated load)
b)SSR/SSC drive output
- Proportion cycle
: 1 to 150 sec.
- Minimum resolution
: 5ms
- ON Voltage
: 10Vdc (8 to 12Vdc)
- OFF Voltage
: 0.5Vdc or less
- Maximum Current
: 20mAdc (per point)
- Load resistance
: 500 ohm or more
c)Current output (4-20mAdc, 0-20mAdc)
- Actual output range
: 0mA to 20.6mAdc
- Accuracy
: ±0.3%FS (1mA or less : ±5%FS)
- Linearity
: ±0.3%FS (1mA or less : ±5%FS)
- Resolution
: 5000 or more
- Ripple current
: P-P0.3mA or less
- Load resistance
: 300 ohm or less
A
B
Y
C
Description
Module type
4ch control module
Input type
Thermocouple / resistance bulb [all channels]
Voltage / current [all channels]
Thermocouple / resistance bulb [ch1,2],
voltage / current [ch3,4]
OUT1,2 output type
Relay output
SSR drive output
Current output
OUT3,4 output type
Relay output
SSR drive output
Current output
Operation Manual
Japanese
English
Option 1
Not fitted
CT input (8 points)
Control module (2ch)
1
2
3
4
5
6
7
P U M
8
9 10 11 12 13
1 - 0
0 0
B
T
A
A
C
E
Y
A
C
E
A
B
Analog re-transmission output
No. of output
Output type
3.2mm
3.2mm
Cable size
0.25 to 1.25mm2
6.0mm or less
Ambient humidity
: DC24V±10%
: Maximum 3.2W (135mA) [when DC24V is applied]
: 30 (W)×100 (H)×85 (D) mm (excluding terminal cover and projection)
: Approx.200g
: DIN rail mounting or mounting inside a cabinet with M3 screws
: -10 to 50 degrees C
* "Ambient temperature" is the temperature underneath the controller
inside the equipment or the cabinet where the controller is installed.
: 90% RH or less (non condensing)
6.0mm or less
Power Supply
Power Consumption
Dimensions
Weight
Installation method
Ambient temperature*
Y
C
: 2 points (OUT3, OUT4 applied)
: Current output (4-20mAdc, 0-20mAdc)
Description
Module type
2ch control module
Input type
Thermocouple / resistance bulb [all channels]
Voltage / current [all channels]
OUT1,2 output type
Relay output
SSR drive output
Current output
OUT3,4 output type
Not fitted
Relay output
SSR drive output
Current output
Operation Manual
Japanese
English
Option 1
Not fitted
CT input (4 points)
Accessories (optional)
Communication functions
RS-485 interface
Communication standard : RS-485
Communication, synchro
method
: Two-wire, half-duplex, asynchronous cycle
Communication speed
: 9.6k, 19.2k, 38.4k, 115.2kbps
Data form
: data bit ; 8, parity ; even/odd/none
Communication distance : 1km (38.4kbps or less), 250m (115.2kbps)
Connectable units
: 33 units (both master and slave units included)
(32 units if any modules other than PUM series is included in slaves)
Protocol
: Modbus RTU compatible
Loader (RS-232C) interface
Communication standard : RS-232C
Communication, synchro
method
: Half-duplex, asynchronous cycle
Communication speed
: 19.2kbps (fixed)
Data form
: data bit 8, no parity
Protocol
: Modbus RTU compatible
Protocol
: Modbus RTU compatible
1
2
3
4
5
P U M Z *
6
7
8
A
A
A
A
L
C
C
C
C
C
0
0
0
0
0
0
0
0
T
T
1
2
3
4
1
1
3
5
1
2
International Sales Div
Sales Group
Description
RS-485 terminating resistance
DIN rail mounting end plate
Side conneting terminal cover (right & left 1 set)
Front face screw terminal cover
Loader connecting cable (RS-232C)
CT input terminal cable (for 4 points) [l=1m]
CT input terminal cable (for 4 points) [l=3m]
CT input terminal cable (for 4 points) [l=5m]
CT for 1 to 30A (CTL-6-S-H)
CT for 2 to 50A (CTL-12-S36-8)
Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome,
Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fujielectric.com
Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425
http://www.fujielectric.com/products/instruments/
-4-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement