Esi EDV-SLD Slider Assembly Guide
PDF
Download
Document
Advertisement
Advertisement
Evolve Universal assembly and operation instructions Monitor arm series Evolve Universal assembly guide Caution • The monitors should not be positioned behind the mounting location of the base. • If the monitor arm is installed ona desk or table with open space behind the arms, it is recommended to install the 180º lockout screws. • Hand tighten screws only. Do not use power tools. 2 Evolve Table of contents Basic components Basic components.................................................................. 4 Configurations F - Fixed / FS - Fixed Slider EVOLVE1-F (SINGLE)............................................... 6 EVOLVE1-FS (SINGLE).............................................. 6 EVOLVE2-F (DUAL)................................................... 6 EVOLVE2-FS (DUAL)................................................. 6 M - Motion / MS - Motion Slider EVOLVE1-M (SINGLE)................................................7 EVOLVE1-MS (SINGLE)..............................................7 EVOLVE2-M (DUAL)...................................................7 EVOLVE2-MS (DUAL).................................................7 FF - Fixed Fixed / FFS - Fixed Fixed Slider EVOLVE1-FF (SINGLE).............................................. 8 EVOLVE1-FFS (SINGLE)............................................ 8 EVOLVE2-FF (DUAL)................................................. 8 EVOLVE2-FFS (DUAL).............................................. 8 EVOLVE3-FF (TRIPLE).............................................. 8 EVOLVE3-FFS (TRIPLE)............................................ 8 FM - Fixed Motion / FMS - Fixed Motion Slider EVOLVE1-FM (SINGLE)............................................. 9 EVOLVE1-FMS (SINGLE).......................................... 9 EVOLVE2-FM (DUAL)................................................ 9 EVOLVE2-FMS (DUAL)............................................. 9 EVOLVE3-FM (TRIPLE)............................................. 9 EVOLVE3-FMS (TRIPLE).......................................... 9 Assembly steps 1. 2. 3. 4. 5. 6. 7. 8. Pole mount........................................................................10 Arm stems.........................................................................13 Attach arms.......................................................................14 Display mounts................................................................16 Attach display...................................................................18 Adjust tension..................................................................19 Lock features...................................................................20 Cable management.......................................................22 Other Allen key storage..................................................................23 Notes For quad and six display configurations, a 28" pole is required. QUAD DISPLAYS: Repeat the DUAL ASSEMBLY (EVOLVE2) on the 28" pole. EVOLVE4-M EVOLVE4-FF EVOLVE4-FM EVOLVE4-MS EVOLVE4-FFS EVOLVE4-FMS SIX DISPLAYS: Repeat the TRIPLE ASSEMBLY (EVOLVE3) on the 28” pole. EVOLVE6-FF EVOLVE6-FM EVOLVE6-FFS EVOLVE6-FMS 3 Evolve Basic components Pole mounts Desk clamp Grommet mount Motion arm Profile view Angle view Profile view Angle view Fixed arm 4 Evolve Basic components Arm stem 1. Rotation tension adjustment 2. Secure arms 3. 180º lock-out Profile view Angle view VESA mount Slider mount Display mount Standard bushing Preinstalled on stem arm & fixed arm Display mount Small bushing Reducer bushing For VESA & slider mounts For VESA & slider mounts 5 Evolve1-F Evolve1-FS Evolve2-F Evolve2-FS More complete instructions for part assembly can be found on the page numbers listed below. This may include, but is not limited to, screws, adjustment knobs, bushings and surface protection. Pole mount (PG. 10) Secure pole mount to worksurface. Arm stem (PG. 13) Slide stem arm over pole and secure in place with the 5mm Allen key. Fixed arm (PG. 14) Insert fixed arm to arm stem. slider or VESA stem fixed arm stem VESA plate (PG. 18) Attach VESA plate to back of monitor. reducer bushing reducer bushing fixed arm Dual (PG. 13) For dual display configurations, reverse the second stem arm on the pole, then repeat configuration on second stem arm. slider or VESA VESA or slider (PG. 17) Attach reducer bushing to vesa or slider. Insert vesa or slider to fixed arm. Quick release (PG. 18) Attach displays using the quick release feature. Tension (PG. 19) Adjust tension on VESA or slider. 6 BUILD 1ST BUILD 2ND Completes Evolve1-F assembly or Completes Evolve1-FS assembly Completes Evolve2-F assembly or Completes Evolve2-FS assembly Evolve1-M Evolve1-MS Evolve2-M Evolve2-MS More complete instructions for part assembly can be found on the page numbers listed below. This may include, but is not limited to, screws, adjustment knobs, bushings and surface protection. Pole mount (PG. 10) Secure pole mount to worksurface. Arm stem (PG. 13) Slide stem arm over pole and secure in place with the 5mm Allen key. Small bushing Small bushing motion arm motion arm Dual (PG. 13) For dual display configurations, reverse the second arm stem on the pole. then, repeat configuration on second stem arm. slider or VESA VESA or slider (PG. 17) Attach reducer bushing to vesa or slider. Insert VESA or slider to motion arm. slider or VESA Motion arm (PG. 14) Insert motion arm to arm stem. stem stem VESA plate (PG. 18) Attach VESA plate to back of monitor. Quick release (PG. 18) Attach displays using the quick release feature. Tension (PG. 19) Adjust tension on VESA or slider. BUILD 1ST BUILD 2ND Completes Evolve1-M assembly or Completes Evolve1-MS assembly Completes Evolve2-M assembly or Completes Evolve2-MS assembly 7 Evolve1-FF Evolve2-FF Evolve3-FF Evolve1-FFS Evolve2-FFS Evolve3-FFS More complete instructions for part assembly can be found on the page numbers listed below. This may include, but is not limited to, screws, adjustment knobs, bushings and surface protection. (pg. 16) Attach reducer bushing to vesa and insert vesa to third stem arm. VESA plate (PG. 18) Attach VESA plate to back of monitor. Quick release (PG. 18) Attach displays using the quick release feature. Tension (PG. 19) Adjust tension on VESA and/or slider. 8 stem fixed arm Triple (PG. 13) For triple display configurations, reverse the second stem arm on the pole, then add a third stem arm. reducer bushing reducer bushing stem stem Dual (PG. 13) For dual display configurations, reverse the second stem arm on the pole. then, repeat configuration on second stem arm. VESA reducer bushing fixed arm VESA or slider (PG. 17) Attach reducer bushing to VESA or slider. Insert VESA or slider to fixed arm. BUILD 3RD fixed arm Fixed arm (PG. 15) Insert fixed arm to fixed arm. Completes Evolve3-FFS assembly or Completes Evolve3-FF assembly fixed arm Fixed arm (PG. 14) Insert fixed arm to stem arm. slider or VESA Stem arm (PG. 13) Slide stem arm over pole and secure in place with the 5mm Allen key. slider or VESA Pole mount (PG. 10) Secure pole mount to worksurface. BUILD 1ST BUILD 2ND Completes Evolve1-FF assembly or Completes Evolve1-FFS assembly Completes Evolve2-FF assembly or Completes Evolve2-FFS assembly Evolve1-FM Evolve2-FM Evolve3-FM Evolve1-FMS Evolve2-FMS Evolve3-FMS More complete instructions for part assembly can be found on the page numbers listed below. This may include, but is not limited to, screws, adjustment knobs, bushings and surface protection. Fixed arm (PG. 14) Insert fixed arm to stem arm. Motion arm (PG. 15) Insert motion arm to fixed arm. slider or VESA Stem arm (PG. 13) Slide stem arm over pole and secure in place with the 5mm Allen key. slider or VESA Pole mount (PG. 10) Secure pole mount to worksurface. Completes Evolve3-FMS assembly or Completes Evolve3-FM assembly BUILD 3RD small bushing small bushing VESA reducer bushing (PG. 16) Attach reducer bushing to VESA and insert VESA to third stem arm. motion arm stem fixed arm fixed arm Triple (PG. 13) For triple display configurations, reverse the second stem arm on the pole, then add a third stem arm. BUILD 1ST Completes Evolve1-FM assembly or Completes Evolve1-FMS assembly stem Dual (PG. 13) For dual display configurations, reverse the second stem armon the pole. Then, repeat configuration on second stem arm. motion arm Vesa or Slider (PG. 17) Attach small bushing to VESA or slider. Insert VESA or slider to motion arm. BUILD 2ND Completes Evolve2-FM assembly or Completes Evolve2-FMS assembly VESA plate (PG. 18) Attach VESA plate to back of monitor. Quick release (PG. 18) Attach displays using the quick release feature. Tension (PG. 17) Adjust tension on motion arm. Adjust tension on VESA and/or slider. 9 Step #1 Pole mount You will receive parts to accommodate either the desk clamp mount or the grommet mount. Option 1 Grommet mount (PG. 12) Secure pre-assembled desk clamp mount to work surface. Convert the desk clamp mount to a grommet mount For worksurfaces between 0.6" - 2.99" thick. 10 Option 2 Desk clamp (PG.11) For worksurfaces up to 1.5” thick. Desk clamp assembly Step 1 Adhere the adhesive pad underneath the base to protect the worksurface. For worksurface 0.66”- 2.2” Optional adjustment for thicker worksurfaces 1.38”‑2.99” Step 2 (optional) Adjust clamp positioning to accommodate a thicker worksurface. Step 3 Slide onto worksurface to desired position. Step 4 Twist to tighten the desk clamp on the worksurface. Step 2A Remove the clamping component from the upper position with the 4mm Allen key. Step 2B Replace the clamping component in the lower position and secure with the 4mm Allen key. 11 Grommet mount assembly Step 1 Remove the 3 screws with the 4mm Allen key. For worksurface up to 1.5” Step 2 Insert the large screw to the grommet plate and reattach the 3 screws with the 4mm Allen key. 4mm Allen key (Included) Step 3 Adhere the adhesive pad underneath the base to protect the worksurface. Step 4 Complete the grommet mount assembly with the remaining components. (bolt should be visible under worksurface) bolt plate washer 14 mm nut 14 mm nut 14 mm wrench (Included) 12 Step #2 Stem arm Each diagram/step may not applicable to your product configuration. Single display configuration Step 1 Slide stem arm over pole and secure with the 5mm Allen key. 5 mm Allen key (Included) Dual display configuration Step 2 Reverse the second stem arm over pole as shown and secure with the 5mm Allen key. NOTE Stem arm is reversed for even alignment Triple display configuration Step 3 Slide VESA stem arm over pole and secure with the 5mm Allen key. NOTE: arm Stems must be secured to pole before attaching additional components Stem arm is stacked on top to hold center monitor. 13 Step #3 Attach arms Each diagram/step may not applicable to your product configuration. Insert a motion arm or fixed arm into a stem arm. motion arm Step 1 Insert motion arm or fixed arm to stem arm. Step 2 Secure the screw using the 2mm Allen key. F fixed arm 1. Rotation tension adjustment 2. Secure arms 2mm Allen key (included) 14 Step #3 Attach arms Insert a motion arm or fixed arm into a fixed arm motion arm Step 1 Insert motion arm or fixed arm to fixed arm. Step 2 Secure the screw using the 2mm Allen key. fixed arm 1. Rotation tension adjustment 2. Secure arms 2mm Allen key (included) 15 Step #4 Display mounts Insert VESA to a stem arm. Step 1 Attach reducer bushing onto VESA mount. For detailed instructions on how to attach the reducer bushing please reference the slider mount instructions. 16 Step 2 Insert VESA mount to arm stem. Step 3 Secure the screw using the 2mm Allen key. Step #4 Display mounts Insert VESA or slider to a motion or fixed arm. reducer bushing small bushing Fixed arm Motion arm Step 1 Attach bushing onto VESA or slider. Step 2 Insert slider mount to motion arm or fixed arm. Step 3 Secure the screw using the 2mm Allen key. 17 Step #5 Attach display VESA plate is pre-drilled to accommodate varying monitor standards. Step 1 Pull the tab to release the quick release VESA plate. 100mm Two options of pre-drilled holes to accommodate varying monitor standards Step 2 Pull the quick release VESA plate upward to detach. 75mm Step 3 Place the monitor face down on a flat surface. Align the VESA plate holes with the back of the monitor and attach using the screws provided. Step 4 With the monitor attached, reinsert the quick release VESA plate. Ensure the monitor “clicks” securely in place. monitor (face down) 18 Step #6 Adjust tension Adjusting the tension on your motion arm allows for smooth adjustments. Tension adjustment supports monitors weighing 6.6 - 17.6 lbs. Adjust motion arm tension Step 1 Use the 5mm Allen key to adjust the tension to correspond to the weight of the monitor. Adjust mount tilt tension Step 2 Use the 4mm Allen key to adjust the tension to correspond to the weight of the monitor. Twist the Allen key in a clockwise direction for heavier monitors; counterclockwise for lighter monitors. 19 Step #7 Lock features Optional features 180° lock monitor arm The 180º lock-out feature allows 90º rotation towards the user, but prevents 90º rotation away from the user. Step 1 Fasten the screw with the 2mm Allen key on the arm stem and then move the Allen key backward one circle motion to limit arm rotation. loosen tighten 20 Step #7 Lock features If desired, the slider mount can be secured to prevent the slider function. This will lock a monitor in position. Lock slider plate lock screw lock screw Prevent VESA mount quick release Step 1 To prevent the quick release function, insert the screw to the back of the VESA mount. 21 Step #8 Cable management Optional features Step 1 Slide cable tray outward to detach from fixed arm. Step 2 Route cables through fixed arm tray and reattach. pole clips Step 1 Detach pole clip and route cables. Step 2 Route cables through cable clip and reattach to pole. 22 Step 1 Squeeze clip then pull to detach the clip from the motion arm. Step 2 Route cables through clip and reattach. Other Additional features Allen key storage Once assembly is complete, place the Allen keys in the slots located on the back side of the VESA and slider mounts. Insert the two smaller Allen keys simultaneously. 23 Evolve Monitor arm series Please contact Customer Service with any questions or comments at 800.833.3746 or visit our website at esiergo.com LIMITED WARRANTY ESI warrants this product to be free from defects in manufacturing for a period of 15 years from the date of original purchase. This warranty extends only to the original purchaser, and does not apply if the product has been damaged or fails to function properly as a result of misuse, abuse, modification, alteration, or improper cleaning or maintenance. This warranty does not apply to damage in shipment caused by carriers, damage caused during installation, normal wear and tear, or excessive use (meaning consistent use in excess of an eight hour shift). ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE. ESI’s sole obligation under this warranty or any implied warranty, and the purchaser’s sole remedy, is limited to the repair or replacement, at ESI’s option, of the product or any defective part. Costs (such as installation, labor fees or express shipping) incurred due to replacement of products are not covered under warranty. IN NO EVENT SHALL FELLOWES, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR SPECIAL DAMAGES. To make a warranty claim, contact ESI at 800-833-3746 or [email protected]. You must provide proof of purchase, such as the original purchase order number. The duration, terms and conditions of this warranty are valid worldwide, except where different limitations, restrictions or conditions may be required by local law. © 2018 Fellowes, Inc. PS Rev A 07/2018 ">

Public link updated
The public link to your chat has been updated.
Advertisement