hd-010c digital drum user`s manual - huaxin

hd-010c digital drum user`s manual - huaxin
HD-010C DIGITAL DRUM
USER’S MANUAL
CAUTION
CAUTION
Any changes or modifications in construction of this device which are not expressly approved by
the party responsible for compliance could void the user’s authority to operate the equipment.
WARNING
When using electrical products, basic safety precautions should always be followed, including the
following:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
Also, this equipment has been tested and found to comply with the limits for following standard:
EN55022-2006
EN55024:1998/+A1:2001/+A2:2003
EN55013:2001/+A1:2003/+A3:2006
EN55020:2007
EN61000-3-2:2006
EN61000-3-3:1995/+A1:2001/+A2:2003
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
TAKING CARE OF YOUR DRUM
!
DO NOT ATTEMPT TO OPEN THE UNIT OR MAKE ANY CHANGE IN THE CIRCUITS OR
PARTS OF THE UNIT.
SERVICE AND MODIFICATION
This product should be serviced by qualified
service personnel when,
w the power supply cord or the plug has
been damaged,
w liquid has been spattered into the unit or it
has been exposed to rain,
w the instrument does not appear to operate
normally or exhibits a marked change in
performance,
w the instrument has been dropped or the
cabinet has been damaged.
w Do not attempt to open the unit or make
any change in the circuits or parts of the
unit.
HANDLING AND TRANSPORT
w Never apply excessive force to the
controls, connectors, pads or other parts
of the instrument.
w Always unplug cables by gripping the plug
firmly, not by pulling on the cable.
w Physical shocks caused by dropping,
bumping, or placing heavy objects on the
instrument can result in scratches and/or
more serious damage.
w Carefully check the amplifier volume
control before stating to play. Excessive
volume can cause permanent hearing
loss.
CLEANING
w Clean the unit with a dry or light-wet soft
cloth. Do not use paint thinner or petrochemical based polishes.
LOCATION
Do not expose the drum to the following conditions to avoid deformation, discoloration, or
more serious damage,
w direct sunlight (near a window),
w high temperatures (near a heat source,
outside, or in a car during the daytime),
w excessive humidity,
w excessive dust,
w strong vibration.
w The drum contains digital circuitry and
may cause interference if placed too
close to radio or television receivers. If
interference occurs, move the drum
further away from the affected
equipment.
POWER
w Turn the power switch off when the
drum is not in use.
w To avoid damage to the drum and other
devices to which it is connected, turn
the power switches of all related devices off prior to connection or disconnection of audio cables.
w Turn the power off if the main cable is
damaged or the instrument is spattered
with liquid.
w Do not switch the unit on and off in quick
succession, this places an undue load
on the electronic components.
w Unplug the AC power cord during an
electrical storm.
w Avoid plugging the AC adaptor into the
same AC outlet as appliances with high
power consumption, such as electric
heaters or ovens.
CONTENTS TABLE
INSTALLATION .................... .....1
SOUND MODULE ..................... .....5
C o n t r o l P a n e l . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . 5
B a c k P a n e l . . . . . . . . . . . . . . . . . . . . . . ...... . . . . . 6
PLAYI N PAD .. .. ... .. ... ... .. ... .. .......... . . .. 7
VOLUME CONTROL ....................................8
DRUM KIT ................................ . . . ... .9
SONG ...............................10
Demo Song .....................................10
User Song ................................11
METRONOME ........................12
Metronome ...........................12
Tempo .... .... .... .... .... .... ......... .12
DRUM KIT EDIT ..........................13
S e l e ct k i t f o r e di t i n g . . . . . . . . . . . . . . . . . . 1 3
Ent er the Edit Mode .. . . .. . . . .. . ..... . .. . 14
S e l e c t p a r t t o e d i t . .. . ... . . . ... . ... . . . . 1 4
Select parameter to edit ..........14
Edit the parameter .................15
Edit another parameter o r p a r t . . ....15
Edit other parameter in the current part..15
Edit anot her par t .. .. .. . .. .. .. .. . .. .. .. .15
Complete the edit ...................16
STRIKING COUNT ..................17
SETUP .............................18
Accompaniment Volume........18
Percussion Volume for Demo Play ...18
Ma ster Tu ne .... ... ... .... ....... .. 18
Count Sesitivity ..................18
Local .........................18
Equalizer...........................19
Advanced Parameter .........19
Sesitivity ..... . . . . . ... . ....20
Headroom .......................20
Trigger Corve ...........................20
Cross Talk ...........................21
Hi-Hat pedal setup ................21
Reset ............................23
RECORD ......................................24
Preparing ..........................24
Record ............................24
Pl ay b ac k Use r So ng . . .......... . . . 2 5
E r a s e U s e r S o n g . . . . . . ........ . . . . 2 5
M I D I & U S B . . . . . . . . . . . . . ......... . . . . . . 2 6
KIT LIST .........................28
V O I C E L I S T . . . . . . . . . . .. . . ........ . . . . . . 2 9
S P E C I F I C A T I O N S . . . ......... . . . . . . 3 2
INSTALLATION
CRASH1
CRASH 2
B-12 Cymbal-edg
B-12 Cymbal-edg
TOM1
HI-HAT
B-8 Tom
A-8 Hi-Hat
TOM2
B-8 Tom
SOUND MODULE
RIDE
HD-010B
B-14 Cymbal-edg-Bell
SNARE
B-8 Snare
TOM3
B-8 Tom
TOM4
B-8 Tom
KICK
B-8 Kick
RACK SYSTEM
HI-HAT CONTROL PEDAL
RACK C
B-HH Ctrl
KICK PEDAL
P-6B Kick Pedal
* KICK PEDAL IS OPTIONAL ACCESORY
The diagram shows complete drum kit after installation.
Each drum pad, cymbal pad and Hi-Hat control pedal has its part number underneath the part name
for your reference in installation. The part number is printed in part packing box.
Power adaptor and connection cables are not shown in the diagram.
1
INSTALLATION
RACK INSTALLATION - 1
Wing nut
These clamps are in the CLAMP box
You can find all components in package.
All pipes with clamp kit attached are in RACK SYSTEM box, except right , left lag and snare arm
without clamp kit, which is in CLAMP box.
Take off all parts from package. Insert pipes into relevant clamp as shown in the daigram, fasten wing
nut to secure them.
2
INSTALLATION
RACK INSTALLATION - 2
Please note: Hi-Hat rod is different
from ride/crash rod.
3 Loosen wing nuts in
the clamp. Rotate the LRod and cymbal support
rod to proper position, then
tighten the wing nuts
2 Loosen wing nut in the
clamp. Move the cross
beam to proper location,
then tighten the wing nuts
1 Loosen wing nuts in the clamp,
adjust the position of the arm and
legs, then tighten the wing nuts
Adjust arm, leg and cross beam to proper position. Insert L-rods and cymbal support rods into relevant clamp as shown in the diagram, then adjust their positions.
3
INSTALLATION
COMPONENTS INSTALLATION
Hi-Hat Installation
1. Remove the wing nut,
washer and felt pad from the
top of the rod.
2 2. Put the Hi-Hat into the
rod, then place back parts
removed in the step 1. Retighten the wing nut.
3. Loosen the side wing nut,
adjust the angle of the rod
then re-tighten the wing nut.
3
4. Loosen the wing nut on the
clamp, adjust the height of
4
the rod then re-tighten the
wing nut.
1
1
2
3
4
Snare Installation
1. Loosen the wing nut,
place the snare on the
snare installation snare
L-Rod.
2. Adjust the angle and height of the
snare pad then tighten the wing nut.
Kick Installation
1. Align holes in the support 1 and stand 2
then insert bolts and fasten with attached
2. Insert tongue 4 of the kick stand into slot of
the pedal 3
3. Align holes in the tongue and the pedal, then
insert bolts and fasten with attached key. .
1
4
Crash and Ride Installation
1. Remove the wing nut,
washer and felt pad from the
top of the rod.
2. Put the cymbal pad into the
rod, then place back parts removed in the stet 1. Fasten
the wing nut but not too tightly.
It allows the pad a little bit wobb li ng li ke r e a l ac o us t i c
cymbal.
3. Loosen the side wing nut,
adjust the angle of the rod
then re-tighten the wing nut.
4. Loosen the wing nut on the
clamp, adjust the height of the
rod then re-tighten the wing
nut.
Tom Installation
1. Loosen the wing nut,
place the tom pad on
the installation L-Rod.
2. Adjust the angle and
height of the tom pad
then tighten the wing
nut.
2
3
P-6B
Sound module Installation
1. Align holes in the sound module and the model mount then insert
screws and fasten it.
2. Insert rod of the model mount into the clamp, then tighten the wing
nut.
Finalizing the Installation
After install all components, fine adjust the arm, clamps and rods to
the best position you desire.
Electronic Connection
Please refer to the SOUND MODULE Chapter for electronic connection.
4
SOUND MODULE
CONTROL PANEL
13
1
12
5
2
11
6
10
3
7
9
14
8
4
(1)
LCD Display: Information display such as Kit number and name, Song name etc.
(2) KIT Button: Enter the Drum kit screen and select kit
(3) SONG Button: Enter the Song mode to play demo or User songs
(4) Sequencer Buttons:
Record Button, Press it to enter the record window
Play/Stop Button
The Play/Stop button is used in both Song and Record operations. Please refer to relevant chapters for detailed information.
(5) COUNT Button: Enter the Count mode to test how fast you can strike
(6) CLICK Button: Metronome switch and edit
(7) TEMPO Button: Change metronome tempo
(8) DATA +/- Knob: Rotate the knob to change data for all operations. The knob is with push
switch, when push the knob down, the switch will be on. Press the knob down then rotate it to
adjust master volume in the Kit Selection and Song window. Pushing down the knob can function
as ENTER button.
(9) ENTER Button: Confirm your operating
(10) EXIT Button: Exit to the previous window or return to the Kit Selection window
(11) SETUP Button: Enter the Setup mode and set parameters
(12) EDIT Button: Enter the Kit Edit mode and edit parameters
(13) MODE Button: Change Demo playing mode
(14) Pad Select Buttons: Select a pad and its part for edit in the Edit mode. These are dualfunction buttons. In the Kit Select mode, they are used for kit quick selection.
5
SOUND MODULE
BACK PANEL
9
10
7
6
4
3
2
1
8
5
(1) Power Switch: Turn On/Off the sound module
Note: When you turn the power off, do not turn it on immediately. Wait at least five seconds to turn
the power on so that the electronic circuits can properly reset.
(2)
Power In Jack: Plug in the DC cable of the attached adaptor
(3) USB Jack: The USB connector allows you to connect the drum directly to your computer’s
USB port. The USB interface is compatible with Windows XP/Vista, Windows 7 and MAC. The
computer will recognize the drum as Audio Device. Please see the MIDI & USB chapter of this
manual for details
(4) MIDI Jack: MIDI jacks allow communication with other products equipped with MIDI
interfaces. Please see the MIDI & USB chapter of this manual for details
(5) Headphone Jack: The drum has stereo headphone jack. You can play in total silence without
disturbing others in the room by plugging a set of headphones into the jack.
(6)
Headphone Volume Knob: Rotate it to adjust the headphone volume
(7) Line In Jack: Line In stereo audio input jack will mix the supplied signal with the internal drum
sound. It can be used to hook up items such as CD players, MP3 player etc.
(8) Line Out Jack: There is no built-in speaker in the drum. Line Out stereo audio output supplies
the drum output signal to external amplification, such as home stereo, PA system or other stand
alone amplifiers. If you connect with external mono system, use L/MONO output and stereo/mono
adapter is recommended.
(9) Pad Trigger Connector: Each pad and Hi-Hat control pedal has labeled cable. All cables are
merged into a single connector. Plug in the cable into jack of corresponding component, Then, plug in
the connector here.
(10) Expanded Pad Trigger Jack: Plug in the cable of the Tom4 into the AUX1 and the Ride into the
AUX2.
6
PLAYIN PAD
TURN ON THE POWER
Playing Cymbal Bell
(1) Adjust volume of external audio device
Strike the bell at the large ride cymbal make
connected with the drum to lower level.
symbal bell sound.
(2) Press the POWER button while don’t strike
pad or press the Hi-Hat control pedal.
(3) Turn on external devices connected.
(4) Strike pad and adjust the volume to proper
level.
PLAYING PADS
All pads have striking force sensitivity feature.
Strike the pad harder to make higher volume
and strike the pad softer to make lower
volume.
Playing Tom Drum
Strike the central position (head) of the pad to
make head sound, strike the rim of the pad to
make rim sound.
Head
Playing Snare Drum
Strike the central position (head) of the pad to
make head sound, strike the rim of the pad to
make rim sound. There are two rim portions with
different rim sound. Also, there is a mark on the
pad to indicate the portion.
Mark
Rim 1
Rim
Head
Rim 2
Playing Hi-Hat
(1) Strike the Hi-Hat pad without pressing the HiHat control pedal to make open Hi-Hat sound.
Playing Cymbal
(2) Strike the Hi-Hat pad with fully pressing the
Strike the central position (bow) of the cymbal
Hi-Hat control pedal to make close Hi-Hat sound.
to make cymbal bow sound, strike the edge of (3) Strike the Hi-Hat pad while pressing the Hithe cymbal to make edge shot sound.
Hat control pedal gradually to make consecutive
open to close Hi-Hat sound.
Bow
Edge (4) Press the Hi-Hat pedal down quickly to make
Hi-Hat pedal sound.
Cymbal Choke
Strike a cymbal, its sound will sustain. Then
squeeze the edge portion to mute the sound.
Please note that the Hi-Hat has no choke
feature.
Playing Kick Drum
Press the Kick drum pedal to make kick
drum sound.
7
VOLUME CONTROL
MASTER VOLUME
In the Kit and Song window, push the DATA knob to
enter the Master Volume control window. The current
volume level will be blinking. Rotate the DATA knob to
change the master volume ranged 0 - 127. Press the
EXIT button, or after about 5 seconds without any
adjustment, it will return to the previous window.
HEADPHONE VOLUME
Adjust the headpnone volume by rotating the HEADPHONE VOLUME knob in the back panel.
8
Master
Volume
115
Volume indicator Master volume
+
DRUM KIT
There are 55 preset drum kits and 35 User Kits. The kit is combination of different instrument voice
assigned to each pad which has unitary style for performance. All the kits are for your choice. Any
kit could be edited and saved as your own User Kit.
After power on and display initial information, it’ll enter the kit selection mode automatically while the
KIT button indicator will light up. The kit number and its name will be displayed.
In some other operation modes, you may press
Kit number
the KIT button to enter the kit select operation
mode.
KIT
01
PRESET KIT
Standard
The preset kit number is ranged 01 - 55.
Rotate the Data knob to select a kit you desire.
Kit name
Rotate the knob clockwise to increase the kit
number and anticlockwise to decrease the kit
+
number. All preset kit number and name are listed
in the Appendix KIT LIST.
Kit number
Note: Normally, striking the drum pad makes
single sound. When you play the Tom rim or Kick
with Kit 22/23/24/25/26, an additional voice will
be added to the basic drum sound. The additional
sound is composed in a sequencer for these specific kits. Each time you play the pad, the additional sound will change in sequence.
Kit
UserKit01
56
User Kit name
+
USER KIT
You can create your own user kit by edit function.
Click the KIT button repeatedly will switch the
Preset Kit and User Kit selection. The User Kit
number is 56 - 90; the User Kit name is UserKit01
- UserKit30.
Rotate the Data knob to select an user kit you
desire in the same way above.
The factory setting for all User Kits is the same
as preset kit 01. You could call them even if you
don’t create your own user kit. Of course, you
could replace it by editing. Please see <EDIT>
Chapter in this manual for details.
QUICK SELECTION
In the Kit mode, ten pad selection buttons are defined as quick kit selection buttons. Each one is
assigned to a most common use kit. Simply press
a button to select kit directly. The default quick
selection assignment is listed in the Appendix
<KIT LIST>.
After you select a kit, you can assign it to a quick
10
9
8
7
6
5
4
3
2
1
Note: These buttons are dual-function buttons. When use them as
quick kit select buttons, the indicator of the EDIT button must be off,
Please see <EDIT> Chapter in this
manual for details.
selection button by pressing and holding down
the KIT button then pressing a pad button.
Your assignment is nonvolatile even the
power turns off.
9
SONG
Press the SONG button and its indicator will
lights up. The song window will appear. There are
two types of song: Demonstration song and User
Song which is recorded by yourself.
1. DEMO SONG
Playing status
Tempo
Time Signature
SONG ■ 100 2/4
01 Baiao De2
(1) Select and Play Demo Song
There are many demo songs built in. The name
and number of demo song, playing status, tempo
and time signature appear on the display. Rotate
the DATE knob to choose a song.
Then press the
button to start play; the button
indicator lights up.
When the demo song is playing, press the
button again to stop the playing, the
indicator
turns off.
Demo Song Number Song Name
Playing status
Tempo
Time Signature
SONG u 102 4/4
28 TangoDance
(2) Demo Song Playing Mode
There are four modes to play song:
PLAY 1 - Playing selected song once
REPEAT 1 - Playing selected song repeatedly
PLAY ALL - Play all songs
REPEAT ALL - Playing all songs repeatedly
Press the SONG button twice to enter the play
mode window. Rotate the DATE knob to change
the playing mode.
The screen will turn back to the previous window
automatically after about 3 seconds, or press the
EXIT button to exit immediately.
Demo Song Number Song Name
+
PLAY MODE
PLAY ALL
(3) Practice with Demo Song
You may practice your own performance with the
demo song.
There are three practice modes for yourchoice:
FULL - When press the
button, you will hear
complete song
DRUM ONLY - When press the
button, you
will hear drum sound only. It helps you to get idea
how to perform drum.
DRUM MUTE - When press the
button, you
will hear background music without drum sound.
Then, you can play drums by yourself.
Press the MODE button repeatedly to change the
practice mode.
The screen will turn back to the previous window
automatically after about 3 seconds, or press the
EXIT button to exit immediately.
The current playing mode
PLAY
PART
DRUM MUTE
The current practice mode
Tip: Volume of drum and background music is
adjustable. Please refer to the Chapter <SETUP>
for more information.
10
SONG
2. USER SONG
Playing status
You can record your performance and save it as
User song. When select song by the DATE knob,
after the last preset demo song, the next song followed will be the first User song. HD-010C can
record 15 User songs.
Tip: You may rotate the t he DATE knob
anticlockwise to reach User Song faster.
SONG ■
UserSong01
User song name
+
The display will show song name and playing status.
If there is no user song recorded, it will show
“*Free*”.
The way of the User song playing is the same as
Demo song playing. The playing mode is also available for User song.
11
METRONOME
1. METRONOME
Tempo Time signature
Press the CLICK button to switch the metronome
On/Off while the current tempo, time signature and
On/Off status will be displayed. After about 5
seconds, this window will exit automatically.
CLICK
In the metronome window, press the ENTER
button or push down the Date knob to enter the
metronome setting window. There are 3 parameters
can be edited, they are metronome volume, time
signature and metronome sound. Rotate the
DATA knob to choose a parameter to edit then
press the [ENTER] to confirm. The parameters are
listed below.
NOTE: Push the Data knob as a button can
implement the same function as press the
ENTER button in many occasions. This is an
easier way to enter your setting. In this
manual, press the [ENTER] means press
either the ENTER button or the DATA knob.
096
On/Off status
CLICK
VOLUME
Parameter
+
CLICK
VOLUME
Rotate the DATA knob to change the setting as
listed below. Press the EXIT button to exit the
and back to the metronome parameter select
window; press the EXIT button again to exit the
metronome window.
4/4
ON
Parameter
102
Setting
Metronome Parameters:
+
VOLUME - Metronome volume ranged 0 - 127, the default setting is 100
TIME SIGNATURE - 1-12/2, 1-12/4, 1-12/8, 1-12/16, The default setting is 4/4
SOUND - Metronome sound, ENG represents English, CHN represents Chinese, MET represents
click sound. The default setting is MET
2. TEMPO
Press the TEMPO button, the current tempo value
will blink. Rotate the DATA knob to change the
tempo ranged 40 - 260. The default is 96.
After about 3 seconds, it will return to the previous window automatically.
TEMPO
096
+
12
DRUM KIT EDIT
A drum kit consists of drum pads, cymbals pads and Hi-Hat pedal physically, which generate sound
in different way such as by striking head or rim of drum pad, striking cymbal bow or edge, pressing Hi-Hat pedal. We call the source to generate sound as Part, for example, the part generating
sound by striking the head of Tom 1 pad is displayed on the screen as Tom1, the part generating
sound by Hi-Hat control pedal is displayed on the screen as Pedal Hi-Hat etc. The detailed
description is listed in Table 1 below.
Each part has multi parameters to determine its sound characteristics such as voice, volume,
reverb level and pan etc. These parameters are listed In Table 2.
Table 1
Tom1 - Head of Tom1
Crash - Head of Crash
Tom1-R - Rim of Tom1
Crash-R - Edge of Crash
Tom2 - Head of Tom2
Ride - Head of Ride
Tom2-R - Rim of Tom2
Ride-R - Edge of Ride
Tom3 - Head of Tom3
Ride-B - Bell of Ride
Tom3-R - Rim of Tom3
Open HiHat - Hi-Hat open
Tom4 - Head of expended Tom
Snare-R1 - Rim1 of Snare
Close HiHat - Hi-Hat close
Pedal HiHat - Hi-Hat Pedal
Kick - Kick
Snare-R2 - Rim2 of Snare
Crash2 - Head of expended Crash
Snare - Head of Snare
Crash2-R - Edge of expended Crash
Tom4-R - Rim of expended Tom
!
The edit feature is to set parameter for each part, partly or for all parts in a kit. Obviously, assigning
voice to the part is most impotant function. This drum has totally 492 voices can be select and
assigned with this function.
This feature makes it possible to change the currently selected drum kit setting. In this way, you
may create your own drum kit and save it as UserKit.
The edit procedure is the same for every parameter, after you are familiar with the operation of
voice assignment; it’ll be easy to edit other parameters.
The following section is the edit procedure taking example how to change voice for a pad.
1. Select kit for editing
Select a kit for editing in the same way explained in the DRUM KIT chapter. The display shows the
kit number and kit name.
KIT
Standard
13
01
DRUM KIT EDIT
2. Enter the Edit Mode
Press EDIT button to engage the edit mode. The indicator will light up.
3. Select part to edit
Press a pad selection button to select a pad. Some
pads have two or more parts, for example, the snare
have head, rim1 and rim2 parts. The default part for a
pad is head or bow.
Press the pad selection button repeatedly and the part
will switch within valid parts one by one. For example,
press the SNARE button once, the part is Snare
(Head); press the SNARE button twice, the part
changes to Snare-R1; press the SNARE button again,
the part will change to Snare-R2. The part name will
apear on the first row of the display. Please refer to
Table 1 for details.
!
Note: Use the EXPAND button to select Tom4
and the Ride. Press the EXPAND button repeatedly,
the part name will change one by one until the part
you desire appears. Please refer to Table 1 for details.
Or, simply strike the proper portion of a pad with normal strenth to select the part directly. Select the HiHat control pedal by pressing it down to the bottom.
4. Select parameter to edit
The current parameter is blinking. Rotate the Data knob
to select a parameter to edit. In this example, select
VOICE.
Press the ENTER button or push down the Date knob
to confirm you choice. The current value/contents of
this parameter will blink.
NOTE: Push the Data knob as a button can
implement the same function as press the ENTER
button in many occasions. This is an easier way
to enter your setting. In this manual, press the
[ENTER] means press either the ENTER button or
the DATA knob.
Edit
Mode
Part Name (Snare head)
Snare
VOICE
Part Name (Tom4 Rim)
Tom4-R
VOICE
Part Name (Snare Rim2)
Snare-R2
VOICE
Parameter name
Snare pad
Part Name (Snare Rim2)
Snare-R2
VOICE Snare-s 1
1
Parameter to edit
+
14
DRUM KIT EDIT
5. Edit the parameter
Rotate the Data knob to change value/contents of
the parameter. In this example, you’ll change voice
assigned to Snare-R2. Any parameter has its own
range to set. For example, there are 492 voices
can be selected to assign to a part, referring to
Appendix VOICE LIST.
Note: When you edit the voice for the Tom rim or
Kick with Kit 22/23/24/25/26, the additional voice
in the sequencer will not be changed.
Part Name (Rim2 for Snare)
Snare-R2
VOICE Snare-S 2
Parameter name
parameter
+
Part Name (Rim2 for Snare)
Snare-R2
VOLUME
110
6. Edit another parameter or part
Now, the first parameter (the VOICE in this
example) editing for a selected part is finished. You
may continue to edit other parameters for this part
or change part to edit.
Parameter to edit
+
(1) Edit other parameter in the current part
Press the EXIT button, the screen will back to the parametr selection window with the parameter
name blinking. Then, select a part by rotating the DATA knob. Then, edit parameters in the same way
above.
Parameters can be edited are listed below:
Table 2
PARAMETER
VOICE
VOLUME
PAN
PITCH
REVERB
DESCRIPTION
Voice assigned to the part
Volume of the part
Stereo pan of the part
Pitch of the part
Reverb effect level of the part
EDIT RANGE
1 – 492
0~127, 127 refers to the highest
volume
-64~63, 0 refers to centre position, -64 to
the most left and 63 to the most right
position
-10~10, 0 refers to standard pitch, -10 to
the lowest and 10to the highest pitch
0~127, 127 refers to the highest level
(2) Edit another part
Press the one of the pad selection button and its indicator will light up. The part name will display on
the screen. The current parameter to edit will keep no change. In this way, you could edit the same
parameter (it is Voice in this example) for each part. Press the same button repeatedly to switch to
another part, if necessary.
Or, simply strike the proper portion in the real pad to select the part directly.
The drum kit still keeps no change in all operations above.
15
DRUM KIT EDIT
7. Complete the edit
After finish all editing for the current drum kit, no matter single or multiple part/parameter, you can terminate the edit.
Press the EXIT button repeatedly until “Save Setups
to ” on the screen. Then, you have two choices:
Save Setups to
56 UserKit01
(1) Save edited drum kit as your own user kit: Rotate
the Date knob to select an user kit number ranged
56 UserKit 01 to 90 UserKit 35. Press [ENTE] to
confirm. The edited results are saved as desired User
kit then exit the edit mode and return to the Kit window.
Save Setups to
58 UserKit03
The user kit setting is nonvolatile even the power turns
off.
(2) Press the EXIT button to exit the edit mode and
return to the Kit window. All the edited results will be
discarded.
16
Select a User kit to save
your edit results
+
STRIKING COUNT
This feature allows you to test how fast you
can strike pad. Press the COUNT button
to enter the striking count window.
COUNT
Time
The examination time could be 1 minute, 2
minutes or 3 minutes. Rotate the DATE
knob to select time.
2Min
Examination time
+
The count will start as soon as you strike
any pad. Count and remaining time will be
displayed on screen. When time is over,
You’ll hear reminding sound for about one
second and the remaining time is 0. Then
you can check the results.
COUNT
1:50
Press the EXIT button to exit this function.
Remaining time
17
100
Striking count
SETUP
Press the SETUP button to enter the setup mode and
its indicator lights up. The Setup window will appear
with the item to be setup and its current value. The
item name will blink. Rotate the DATA knob to select
one of the 8 items below, press the [ENTER] to confirm.
The item name will stop blink and its parameter value
will start blink. Then, you can change parameter value.
Press the [ENTER] to confirmyour setting and turn to
the next item, or press the EXIT button to cancel the
setting and back to the item selection window.
In the SETUP item selection window, press the EXIT
button to turn to the Kit window..
1 Accompaniment Volume
When play demo song, you’ll hear percussion performance accompanied by background music. The parameter for the accompaniment volume is BACK
VOLUME. Rotate the DATE knob to change the volume ranged 0 - 24.
2. Percussion Volume for Demo Playing
When play demo song, the parameter for the volume
of percussion section performance is KIT VOLUME.
Rotate the DATE knob to change the volume ranged
0 - 24.
3. Master Tune
This parameter affects sound pitch globally. In the
“MASTER TUNE window, Rotate the DATE knob to
change the master tuning ranged -50 - 50. 0 refers to
standard 440 Hz frequency for A4 note.
4. Count Sensitivity
The parameter for the sensitivity of the striking count
test is COUNT SENS. Rotate the DATE knob to
change the sensitivity ranged 0 - 24. It is suggested
to set the sensitivity lower than your normal
performance.
5. Local
When Local is On, you can hear sound by headphone
or external speaker. When it is Off, built-in sound engine is turned off; therefore you cannot hear sound
but the drum transmits MIDI message of your playing.
Rotate the DATE knob to switch On/Off status. The
default setting is On.
SETUP
BACK VOLUME 14
Parameter name
+
SETUP
BACK VOLUME 16
Change the volume
+
SETUP
KIT VOLUME 18
Change the volume
+
SETUP
MASTER
TUNE 00
Change the tuning
+
SETUP
COUNT
SENS 16
Chang the count sensitivity
+
SETUP
LOCAL
On
Local status
+
18
SETUP
6. Equalizer
Tone of the drum can be adjusted globally by builtin Equalizer. There are 10 types of preset equalizer listed below.The parameter for select the
equalizer type is EQ. Rotate the DATE knob to
change the type code of the equalizer ranged 1 10.
No.
EQUALIZER TYPE
No.
SETUP
EQUALIZER
004
Change equalizer type
+
EQUALIZER TYPE
1
Normal 1
6
Bright Mid
2
Normal 2
7
Bright
3
Bass Boost
8
Bright High
4
Bass Mid
9
Moderate 2
5
Moderate
10
Bright Mid 2
Press the EXIT button to turn back to the item
selection window.
7. Advanced Parameter Setup
Chapter DRUM KIT EDIT introduces the sound edit procedure. The purpose of the sound edit is to
change sound characteristics such as voice, volume, pan etc. The objects of advanced parameter
edit are physical characteristics of pad such as sensitivity, trigger curve etc.
Any parameter is assigned for each pad individually. You must select a pad to edit. The default pad
is Tom1. You can select pad to setup by pressing the pad select button or striking the pad directly.
Note:
1. There is no alternative part such as rim, edge can be selected. It is different from part selection
procedure in DRUM KIT EDIT. Also, you can select pad by hitting any part of the pad.
2. The procedure of the Hi-Hat control pedal setting is introduced in Hi-Hat Pedal Setting section
separately.
Pad name
After ADVANCED item is selected by the DATA knob
and press the [ENTER] to confirm, you can select pad
to setup by pressing the pad select button or striking
the pad directly.
Press the [ENTER] to confirm your pad selection. The
advanced parameter will appear and blink.The default
parameter is Sensitivity.
Rotate the DATA knob to select parameter. Press the
[ENTER] to confirm. Its current value will appear and
blink. Then, edit the parameter value by rotating the
DATA knob. Press the [ENTER] to confirm your setting and turn to the next parameter. Press the EXIT
button to give up current operation and back to Advanced parameter select window.
Tip: You can try setting results in real time.
19
Snare
ADVANCED
Advanced Mode
Pad name
Snare ADVANCED
Sensitivity
Parameter name
SETUP
Pad name
Snare ADVANCED
Sensitivity 50
There are 4 advanced parameters can be setup in
the way described above.
Parameter name
Parameter value
Sensitivity
The pad sensitivity is ranged 1-127. Rotate the
DATA knob to change it. The higher value represents the higher sensitivity. Please note that if the
sensitivity is too high, it’ll cause unexpected sound
even if you don’t strike the pad.
Snare ADVANCED
Sensitivity 50
Headroom
This feature allows you to set playing strength for
reaching the maximum volume, to accommodate your
personal taste of performance. Strike the pad with
strength, with which you want to get the maximum
volume.The value will appear automatically per your
striking, the Max. value is 127.
Snare ADVANCED
Headroom
64
Trigger Curve
The trigger curve refers to how trigger signal’s
dynamic response relates to your pad striking. This
feature allows you select a proper curve from 6
preset curves to control the relation between the
striking strength and volume change. Change the
curve until the response feels as natural as
possible.
Rotate the DATA knob to choose a curve. The corves
you may select are Linear, Exp1, Exp2, Log1, Log2
and Spline. The default curve is Linear.
Snare ADVANCED
Trigger LINEAR
Strength
Linear
Strength
Exp
Volume
Volume
Volume
Volume
Diagram of 4 types of the curve
Strength
Log
20
Strength
Spline
SETUP
Source pad of Xtalking
Cross Talk
When strike a pad, other pad(s) may sound
occasionally. It is called cross talk. This feature alSnare ADVANCED
lows you to eliminate the cross interference among
Xtalk TOM1 030
the pads. The pad desplayed in the first row of the
screen is source of the cross talk which cross-fire
other pad(s), i.e. when strike this pad, other pad(s)
Pad affected by Xtalking
Xtalking coefficient
will sound. This pad is that you selected for setup.
The procedure of eliminating the cross talk is:
- Select a pad which is affected by cross talking by pressing a pad select button or strike a pad with
middle strenth.
- Rotate the DATA knob to change the cross talk coefficient ranged 0 - 127. The larger value will
reduce unexpected cross talking sound, but too large value will cause sound missing. You should
balance it carefully.
- Press the [ENTER] to confirm your setting. The display will stay on the Cross Talk setting for the
current source pad. You could select another pad which is also affected by the current pad and
continue your setting.
- Press the EXIT button to exit current operation and back to Advanced parameter select window.
Hi-Hat Pedal Setting
Strike the Hi-Hat pad without pressing the Hi-Hat control pedal to make open Hi-Hat sound (voice No.
286 - 304).
The Hi-Hat pedal has two zones of sound control, which is divided by Close Threshold point. Strike
the Hi-Hat pad while pressing the Hi-Hat control pedal gradually to make consecutive open to close
Hi-Hat sound when pedal pressing position is higher than closs threshold. When pedal position is
lower than close threshold, striking the Hi-Hat pad makes close Hi-Hat sound (voice No. 249 - 285).
When press the pedal quickly and reach the pedal threshold point, it'll make Hi-Hat pedal sound
(voice No. 305 - 316) even don’t strike the Hi-Hat pad. The pressing pedal is quicker, the volume is
higher. This bottom position is called Pedal Threshold.
The scale of Hi-Hat pedal movement is 0 - 127. The top position of the pedal is defines as 127 and
bottom is 0.
This feature allows you to set thresholds per your comfortable pressing strength.
The Hi-Hat pedal setting is different from other pads.
When select Sensitivity paramete, press the H.PEDAL
button, the pad name will be Pedal. The first parameter is Closs THR and its current closs threshold
value will be shown and blinking.
21
Hi-Hat Pedal setup
PEDAL
Close
ADVANCED
THR
48
Close THR value
SETUP
Then, press the pedal to position you desire as closs threshold while the real threshold value will be
shown and blinking.
Press the ENTER button to confirm and turn to the bottom threshold setting; the parameter is Pedal
THR.
Then, set the Pedal threshold in the same way above.
Press the ENTER button to confirm.
Press the EXIT button to exit current operation and
back to Advanced parameter select window.
Hi-Hat Pedal setup
PEDAL
Pedal
ADVANCED
THR
30
Pedal THR value
In the Advanced parameter select window, press the EXIT button to back to the SETUP item
selection window. If you did some changes during the Advanced setting, the changes will be saved
automatically. The display will say “Saving...”.
The settings saved is nonvolatile even the power turns off.
22
SETUP
8. Reset
After setup, kit editing and recording, all of changes
are saved in the unit. This feature allows you to recover the factory settings.
Select PARAMETER RESET in the SETUP parameter selection window then press [ENTER]. The reset
window will appear.
SETUP
PARAMETER RESET
+
There are four reset modes:
Kits - Reset sound parameters in all User kits which
changed during the kit editing.
Parameter - Reset changes in Setup operation, except Advanced setting
UserSong - Erase all songs recorded by user
All - Besides reset all items above, it also reset physical parameters changed during the Advanced setting.
Paramter
ALL
Reset
Select Reset type
Rotate the DATA knob to select mode then press
[ENTER]. The dialog screen will appear.
Press the ENTER button to confirm or press the EXIT
button to cancel the reset operation and back to the
Advanced parameter select window.
+
NOTE: Don not strike any pad after press the ENTER button until the KIT indicator lights up. It needs
couple of second.
Are You Sure
[ENTER]or[EXIT]
In the Reset mode selection window, press the EXIT button to back to the Advanced parameter
select window.
In the Advanced parameter select window, press the EXIT button to turn to the SETUP item select
window.
23
RECORD
Press the
button to enter the record window.
The indicator will blink and the current tempo, time
signature and record status are shown on the screen.
Now, it is ready for recording. You may start record
right now by pressing the
button. Or, you could
make necessary setup for your record. If you want to
start record with the current setting, please skip the
step 1 “Preparing”.
Record status
REC.
096
4/4
Tempo Time signature
1. Preparing
As soon as you rotate the DATA knob, setup item will
appear and blink. Roate the DATA knob to select item
you want to setup, then press the [ENTER] to confirm.
The value of the parameter will blink. Items can be
setup are as follws.
REC.
(1) TEMPO - It is the tempo for recording ranged 20 260. Rotate the DATA knob to change it.
TEMPO
(2) P-TEMPO - It is the tempo for playing back your
recording ranged 20 - 260. It makes it possible that
play with slower speed when recording and playback
with faster tempo. Rotate the DATA knob to change
it.
Select Item
(3) TIME-SIG - The time signature for the metronome.
Rotate the DATE knob to choose one you desire.
Please refer to the <METRONOME> chapter of this
manual.
096
4/4
96
+
REC.
TEMPO
096
4/4
120
Set the value
(4) M-SOUND - The metronome sound. Rotate the
DATE knob to choose one you desire. Please refer
to the <METRONOME> chapter in this manual.
+
(5) METRO - Metronome On or Off during the record.
Rotate the DATE knob to switch On and Off.
Tip: If you don’t need to set some items, simply press
the [ENTER] to jump to the next item.
After seting, press the EXIT button to back to the preparing window. Press the EXIT button again to the
record window. You can start record under both
windows.
2. Record
Press the
button to start record. The indicator will stop blinking and keep lighting.
After 4 beats count-in, the record starts immediately,
no matter you start play or not. The record
measure count will appear on the display. Also,
the current beat in the measure will be displayed
with numbers of “----” mark.
Record status
REC.
120
001____
Measure Beat
24
4/4
RECORD
Press the
button again to stop the recording.
The screen will go to the save window. The Max
measure can be recorded is 255, When the
measure counter reaches the Max, the screen
also goes to the save window.
In the save window, a song name for saving your
record will blink. You may rotate the DATE knob
to choose song name. Press the [ENTER] to save
recorded song, press the EXIT button to turn to the
Kit window without saving.
Save the Song
UserSong01
Song name for saving the record
If the song name was already used for the previous recording, it’ll ask you do you want to replace it
with the new recording? Press the [ENTER] to
save it the turn to the Kit window, or press the
EXIT button to back to the previous window
for selecting another song name.
Cover UserSong?
[ENTER]or[exit]
HD-010C can record 15 User songs.
3. Play back User Song
In the saving window, press the
playback your recording. Press the
again to stop the playback.
button to
button
In the Song window, you could also select recorded user song to playback. Please refer to
the <SONG> chapter in this Manual.
4. Erase User Song
Press the SONG button to enter the Song window.
Select a recorded User song then press the
[ENTER] to enter the User Song Delete window.
The User Song name will blink. Press the [ENTER]
to erase the song and “Free” will appear to indicate
that this song is erased successfully.
Or, press the EXIT button to cancel the delete operation and turn to the Kit window.
Delete User Song
UserSong01
The User Song will be erased
The User Song is erased
SONG
*Free*
UserSong01
25
MIDI & USB
MIDI refers to Musical Instrument Digital Interface. This is a world wide standard communication
interface that enables electronic musical instruments and computers to communicate each other
so that musical message can pass between them. This exchange of information makes it possible
to create a system of MIDI instruments and devices that offers far greater versatility and control
than is available with isolated instruments. Whether you interface with computers, sequencers,
expanders or other equipment your musical horizons will be greatly enhanced. For instance, you
can edit your playing in computer or playback MIDI song from computer while play the drum.
MIDI - The MIDI connector allows you to connect the drum directly to another MIDI divice.
1.
MIDI In: This terminal receives MIDI data from an external MIDI device.
2.
MIDI Out: This terminal transmits data from this instrument to other MIDI devices. The
transmitted data includes the note and touch velocity produced while playing on the drum,
as well as voice changes and recorded playback. Demo songs not transmitted.
USB - The USB connector allows you to connect the drum directly to your computer. It can
connected without driver installation under the Windows XP, Windows Vista, Windows 7 &
MAC OSX environment. The drum will be recognized as USB Audio device to receive and
transmit the same MIDI messages described above.
26
MIDI & USB
MIDI APPLICATION CHART
Function
Transmitted
Recognized
Basic Channel
10
1-16
Note Number
0-127
0-127
1-127
64
1-127
0-127
Major Controls:
B9h 04h xxh
Bxh 79h 00h
Bxh 7Bh 00h
Yes
Yes
Yes
X
Yes
Yes
Program Change
X
Yes *
System Exclusive
Yes
Yes **
RPN
X **
Yes **
NRPN
Yes
Yes **
Velocity:
Note ON
Note OFF
Remarks
Hi-Hat pedal control
Reset All Controller
All Notes OFF
* Chanel 10 supports Bank 0 only
** If you need detailed information about Exclusive, RPN and NRPN, please contact your
vender
Note: Transmited note through chanel 10 for each pad if fixed as below:
PAD
NOTE
PAD
NOTE
Tom1
48
Crash2
57
Tom1 Rim
62
Crash2 Edge
52
Tom2
45
Ride
51
Tom2 Rim
63
Ride Edge
59
Tom3
41
Ride Bell
53
Tom3 Rim
64
Hi-Hat Open
46
Tom4
Tom4 Rim
43
76
Hi-Hat Close
Hi-Hat Pedal
42
44
Snare
38
Kick
36
Snare Rim1
37
Ride Mute
6
Snare Rim2
40
Crash Mute
7
Crash
55
Crash2 Mute
5
Crash Edge
49
!
27
KIT LIST
1
Standard
31
Bloom
U06
UserKit06
2
Rock
32
Power Jazz
U07
UserKit07
3
4
Jazz
Wood DJ
33
34
Pop Rock
Boxer
U08
U09
UserKit08
UserKit09
5
HipHop
35
Moby
U10
UserKit10
6
Sand Bag
36
Pop Blue
U11
UserKit11
7
B-Box
37
Walker
U12
UserKit12
8
1-std Drum
38
Joy
U13
UserKit13
9
10
Room Drum
Chinese
39
40
Comet
BrushDrum
U14
U15
UserKit14
UserKit15
11
12
13
Funky
2-std Drum
DoubleBass
41
42
43
Pop Brush
Asian
Run
U16
U17
U18
UserKit16
UserKit17
UserKit18
14
15
16
E-Drum
BigLud
Mass
44
45
46
Largeamb
Slap
MotoDrum1
U19
U20
U21
UserKit19
UserKit20
UserKit21
17
18
19
POWlay
March
Jama
47
48
49
MotoDrum2
OrcDrum
MadDrum
U22
U23
U24
UserKit22
UserKit23
UserKit24
20
21
Latin
Who
50
51
Power Roll
Brtap
U25
U26
UserKit25
UserKit26
22
23
24
25
JoJo
Real Drum
Elec Drum
TR808 Drum
52
53
54
55
DcBass
E-Box
LudNa
Elec DJ
U27
U28
U29
U30
UserKit27
UserKit28
UserKit29
UserKit30
26
27
28
TexBlues
TR909 Drum
PennyRo
U01
U02
U03
UserKit01
UserKit02
UserKit03
U31
U32
U33
UserKit31
UserKit32
UserKit33
29
30
Power Elec
Crush
U04
U05
UserKit04
UserKit05
U34
U35
UserKit34
UserKit35
QUICK SELECTION
BUTTON No.
1
2
KIT No.
1
KIT NAME
Standard
3
9
12
Room Drum
2-std Drum
4
5
6
15
23
25
BigLud
Real Drum
TR808 Drum
7
36
Pop Blue
8
9
37
49
Walker
Mad Drum
10
50
Power Roll
28
Note: Default assignment for
all User Kits is Standard
VOICE LIST
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Name
GM1
GM2
GM3
GM4
GM5
GM6
GM7
GM8
GM9
GM10
GM11
GM12
GM13
GM14
GM15
GM16
GM17
GM18
GM19
GM20
GM21
GM22
GM23
GM24
GM25
GM26
GM27
GM28
GM29
GM30
GM31
GM32
GM33
GM34
GM35
GM36
GM37
GM38
GM39
GM40
GM41
GM42
GM43
GM44
GM45
No.
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Name
GM46
GM47
GM48
GM49
GM50
GM51
GM52
GM53
GM54
GM55
GM56
GM57
GM58
GM59
GM60
GM61
Kick 1
Kick 2
Kick 3
Kick 4
Kick 5
Kick 6
Kick 7
Kick 8
Kick 9
Kick 10
Kick 11
Kick 12
Kick 13
Kick 14
Kick 15
Kick 16
Kick 17
Kick 18
Snare-S 1
Snare-S 2
Snare-S 3
Snare-S 4
Snare-S 5
Snare-S 6
Snare-S 7
Snare-S 8
Snare-S 9
Snare-S 10
Snare-S 11
No.
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
29
Name
Snare-S 12
Snare-S 13
Snare-S 14
Snare-S 15
Snare-S 16
Snare 1
Snare 2
Snare 3
Snare 4
Snare 5
Snare 6
Snare 7
Snare 8
Snare 9
Snare 10
Snare 11
Snare 12
Snare 13
Snare 14
Snare 15
Snare 16
Snare 17
Snare 18
Snare-R 1
Snare-R 2
Snare-R 3
Snare-R 4
Snare-R 5
Snare-R 6
Snare-R 7
Snare-R 8
Snare-R 9
Snare-R 10
Snare-R 11
Snare-R 12
Snare-R 13
Snare-R 14
Snare-R 15
Snare-R 16
Snare-R 17
Tom-Fl 1
Tom-Fl 2
Tom-Fl 3
Tom-Fl 4
Tom-Fl 5
No.
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
Name
Tom-Fl 6
Tom-Fl 7
Tom-Fl 8
Tom-Fl 9
Tom-Fl 10
Tom-Fl 11
Tom-Fl 12
Tom-Fl 13
Tom-Fl 14
Tom-Fl 15
Tom-Fl 16
Tom-Fl 17
Tom-Fl-R1
Tom-Fl-R2
Tom-Fl-R3
Tom-Fl-R4
Tom-Lo 1
Tom-Lo 2
Tom-Lo 3
Tom-Lo 4
Tom-Lo 5
Tom-Lo 6
Tom-Lo 7
Tom-Lo 8
Tom-Lo 9
Tom-Lo 10
Tom-Lo 11
Tom-Lo 12
Tom-Lo 13
Tom-Lo 14
Tom-Lo 15
Tom-Lo 16
Tom-Lo 17
Tom-Lo-R1
Tom-Lo-R2
Tom-Lo-R3
Tom-Lo-R4
Tom-Mi 1
Tom-Mi 2
Tom-Mi 3
Tom-Mi 4
Tom-Mi 5
Tom-Mi 6
Tom-Mi 7
Tom-Mi 8
VOICE LIST
No.
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
Name
Tom-Mi 9
Tom-Mi 10
Tom-Mi 11
Tom-Mi 12
Tom-Mi 13
Tom-Mi 14
Tom-Mi 15
Tom-Mi 16
Tom-Mi 17
Tom-Mi-R1
Tom-Mi-R2
Tom-Mi-R3
Tom-Mi-R4
Tom-Hi 1
Tom-Hi 2
Tom-Hi 3
Tom-Hi 4
Tom-Hi 5
Tom-Hi 6
Tom-Hi 7
Tom-Hi 8
Tom-Hi 9
Tom-Hi 10
Tom-Hi 11
Tom-Hi 12
Tom-Hi 13
Tom-Hi 14
Tom-Hi 15
Tom-Hi 16
Tom-Hi 17
Tom-Hi-R1
Tom-Hi-R2
Tom-Hi-R3
Tom-Hi-R4
HH-Clo 1
HH-Clo 2
HH-Clo 3
HH-Clo 4
HH-Clo 5
HH-Clo 6
HH-Clo 7
HH-Clo 8
HH-Clo 9
HH-Clo 10
HH-Clo 11
No.
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
Name
HH-Clo 12
HH-Clo 13
HH-Clo 14
HH-Clo 15
HH-Clo 16
HH-Clo 17
HH-Ped 1
HH-Ped 2
HH-Ped 3
HH-Ped 4
HH-Ped 5
HH-Ped 6
HH-Ped 7
HH-Ped 8
HH-Ped 9
HH-Ped 10
HH-Ped 11
HH-Ped 12
HH-Ped 13
HH-Ped 14
HH-Ped 15
HH-Ped 16
HH-Op 1
HH-Op 2
HH-Op 3
HH-Op 4
HH-Op 5
HH-Op 6
HH-Op 7
HH-Op 8
HH-Op 9
HH-Op 10
HH-Op 11
HH-Op 12
HH-Op 13
HH-Op 14
HH-Op 15
HH-Op 16
HH-Op 17
HH-Op 18
Crash1-E 1
Crash1-E 2
Crash1-E 3
Crash1-E 4
Crash1-E 5
No.
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
3930
Name
Crash1-E 6
Crash1-E 7
Crash1-E 8
Crash1-E 9
Crash1-E 10
Crash1-E 11
Crash1-E 12
Crash1-E 13
Crash1-E 14
Crash1-E 15
Crash1-E 16
Crash1-E 17
Crash 1
Crash 2
Crash 3
Crash 4
Crash 5
Crash 6
Crash 7
Crash 8
Crash 9
Crash 10
Crash 11
Crash 12
Crash 13
Crash 14
Crash 15
Crash 16
Crash 17
Crash 18
Crash 19
Crash 20
Crash 21
Crash 22
Crash 23
Crash 24
Crash 25
Crash 26
Ride-B 1
Ride-B 2
Ride-B 3
Ride-B 4
Ride-B 5
Ride-B 6
Ride-B 7
No.
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
Name
Ride-B 8
Ride-B 9
Ride-B 10
Ride-B 11
Ride-B 12
Ride-B 13
Ride-B 14
Ride-B 15
Ride-B 16
Ride-B 17
Ride-B 18
Ride 1
Ride 2
Ride 3
Ride 4
Ride 5
Ride 6
Ride 7
Ride 8
Ride 9
Ride 10
Ride 11
Ride 12
Ride 13
Ride 14
Ride 15
Ride-E 1
Ride-E 2
Ride-E 3
Ride-E 4
Ride-E 5
Ride-E 6
Ride-E 7
Ride-E 8
Ride-E 9
Ride-E 10
Ride-E 11
Ride-E 12
Ride-E 13
EFX 1
EFX 2
EFX 3
EFX 4
EFX 5
EFX 6
VOICE LIST
No.
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
Name
EFX 7
EFX 8
EFX 9
EFX 10
EFX 11
EFX 12
EFX 13
EFX 14
EFX 15
EFX 16
EFX 17
EFX 18
EFX 19
EFX 20
EFX 21
EFX 22
EFX 23
EFX 24
EFX 25
EFX 26
EFX 27
EFX 28
EFX 29
EFX 30
EFX 31
No.
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
Name
EFX 32
EFX 33
EFX 34
EFX 35
EFX 36
EFX 37
EFX 38
EFX 39
EFX 40
EFX 41
EFX 42
EFX 43
EFX 44
EFX 45
EFX 46
EFX 47
EFX 48
EFX 49
EFX 50
EFX 51
EFX 52
EFX 53
EFX 54
EFX 55
EFX 56
No.
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
Name
EFX 57
EFX 58
EFX 59
EFX 60
EFX 61
EFX 62
EFX 63
EFX 64
EFX 65
EFX 66
EFX 67
EFX 68
EFX 69
EFX 70
EFX 71
EFX 72
EFX 73
EFX 74
EFX 75
EFX 76
EFX 77
EFX 78
EFX 79
EFX 80
EFX 81
No.
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
Name
EFX 82
EFX 83
EFX 84
EFX 85
EFX 86
EFX 87
EFX 88
EFX 89
EFX 90
EFX 91
EFX 92
EFX 93
EFX 94
EFX 95
EFX 96
EFX 97
EFX 98
EFX 99
EFX 100
EFX 101
EFX 102
Snare I
Snare Side
Snare Rim
INDEX
Voice Number
1 - 61
62 - 79
80- 95
96 - 113
114 - 130
131- 147
148 - 151
152 - 168
169 - 172
173 - 189
190 - 193
Category
Voice
Category
Number
194 - 210
211 - 214
215 - 231
232- 247
248 - 265
266 - 282
283 - 308
309 - 326
327 - 341
342 - 354
355 - 456
457 - 459
GM Kit
Kick
Snare Side Stick
Snare Head
Snare Rim-Shot
Floor Tom
Floor Tom Rim
Tom Low Head
Tom Rim-Shot
Tom Mid Head
Tom Mid Rim-Shot
31
Category
Tom High Head
Tom Hi Rim-Shot
Hi-Hat Close
Hi-Hat Pedal
Hi-Hat Open
Crash Edge
Crash Bow
Ride Bell
Ride Bow
Ride Edge
EFX
Additional Snare
Category
SPECIFICATIONS
Configuration
Voice
Drum Kit
Demo Song
Sound Effects
Equalizer
Metronome
Count Exercise
Pad Edit
Setup Menu
Record
Display
Power
Aux. Socket
4 X 8” Tom (with rim), 8” Snare (double rims), 2 X12” Crash cymbal l
(with Edge & choke), 14” Ride cymbal l (with Edge, Bell & choke), 8”
Hi-Hat, 8” Kick, Hi-Hat pedal
459
55 preset kits and 35 user kits
74, Full, Drum Only and Mute mode
Reverb effect with professional DSP processor
10 preset types
Tempo, Time signature, Sound
1 – 3 minutes
Voice, Volume, Pan, Pitch, Reverb level
Accomp & Drum volume for Demo, Master tuning, count sensitivity,
Equalizer, Advanced (Sensitivity, Dynamic range, Velocity Curve,
Cross talk, Hi-Hat Pedal), Reset
15 Songs
Back-light LCD, 2 Row X 16 Characters
9V DC
Headphone, Line In/Out, MIDI In/Out, USB, Power In
All specifications are subject to change without notice
32
HD-010C DIGITAL DRUM
USER
’S MANUAL
Shanghai Huaxin Musical Instrument Co., Ltd.
35 Lao Shan Yi Cun
Shanghai 200120
China
Tel: +86-21-58820000
Fax: +86-21-58783113
Email: [email protected]
www.huaxin-music.com
Rev. 1.02C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement