EGO HT2410E 56 Volt Lithium-Ion Cordless Hedge Trimmer User Manual

OPERATOR'S MANUAL
56 VOLT LITHIUM-ION
CORDLESS HEDGE TRIMMER
MODEL NUMBER HT2410E/HT2000E
WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
MNL_EGO_HT2410E / HT2000E_AV01.01_210518
A
1. Hanging hole
4. Hand guard
3. Blade
5. Front handle
2. Tip protector
6. Lock-off button
7. Rear handle
8. Battery-release button
9. Latch
10. Electric contacts
11. Battery-mounting slot
14. Front switch lever
15. Hanging hole 16. Sheild
B
13. Rear switch lever
12. Battery-ejection mechanism
C
1
2
D
E
F
G
H
I
Cutter Tooth
Guard Tooth
J
READ ALL INSTRUCTIONS!
READ OPERATOR’S MANUAL
Residual risk! People with electronic devices, such
as pacemakers, should consult their physician(s) before
using this product. Operation of electrical equipment
in close proximity to a heart pacemaker could cause
interference or failure of the pacemaker.
XX
WARNING: To ensure safety and reliability, all
repairs and replacements should be performed by a
qualified service technician.
SAFETY SYMBOLS
WARNING, or CAUTION. May be used in conjunction with
other symbols or pictographs.
WARNING: The operation of any power tools can
result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power
tool operation, always wear safety goggles or safety glasses
with side shields and a full face shield when needed. We
recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
SAFETY INSTRUCTIONS
This page depicts and describes safety symbols that may
appear on this product. Read, understand, and follow
all instructions on the machine before attempting to
assemble and operate.
4
Read
Operator’s
Manual
To reduce the risk of injury,
user must read operator’s
manual.
Noise
Guaranteed sound power
level.
Wear Eye
Protection
Always wear safety goggles
or safety glasses with side
shields and a full face shield
when operating this product.
Do Not
Expose To
Rain
WARNING: Do not use in the
rain or leave outdoors while it
is raining.
Keep
hands and
feet away
from the
cutting
tool
WEEE
Waste electrical products
should not be disposed of
with household waste. Take
to an authorized recycler.
Ingress
Protection
Degree
Protection from splashing
water
Volt
Voltage
min-1
Direct
Current
Per Minute
Type or a characteristic of
current
Revolutions per minute
mm
millimeter
Length or size
cm
Centimeter
Length or size
n0
No Load
Speed
Rotational speed, at no load
WARNING: Be sure to read and understand all
safety instructions in this Operator’s Manual, including all
safety alert symbols such as “DANGER,” “WARNING,”
and “CAUTION” before using this tool. Failure to follow all
instructions listed below may result in electric shock, fire,
and/or serious personal injury.
SAFETY ALERT SYMBOL: Indicates DANGER,
Indicates a potential personal
injury hazard.
Never attempt to operate your
power tool with one hand.
Loss of control of the power
tool resulting in serious or fatal
injury may result. To reduce
the risk of cut injuries, keep
hands and feet away from
the cutting tool. Never attach
a moving cutting tool with
your hand or any other part of
your body.
The purpose of safety symbols is to attract your attention
to possible dangers. The safety symbols and the
explanations with them deserve your careful attention
and understanding. The symbol warnings do not, by
themselves, eliminate any danger.
The instructions and warnings they give are no substitutes
for proper accident prevention measures.
SYMBOL MEANING
Safety Alert
IPX4
V
XX
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings,
instructions, illustrations and specifications provided
with this pool tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
Save all warnings and instructions for future reference.
◾
Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
◾
Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
◾
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
◾
Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
◾
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
devices can reduce dust-related hazards.
◾
Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
WORK AREA SAFETY
◾
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
◾
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
◾
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
◾
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
◾
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
◾
Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
◾
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
◾
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
◾
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
PERSONAL SAFETY
◾
◾
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
POWER TOOL USE AND CARE
◾
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and more safely at the rate for which
it was designed.
◾
Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
◾
Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
◾
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of
untrained users.
◾
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
5
◾
◾
◾
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
is maintained.
◾
HEDGE TRIMMER SAFETY WARNINGS
◾
Keep all parts of the body away from the cutter
blade. Do not remove cut material or hold material
to be cut when blades are moving. Make sure
the switch is off when clearing jammed material.
A moment of inattention while operating the hedge
trimmer may result in serious personal injury.
◾
Carry the hedge trimmer by the handle with the
cutter blade stopped. When transporting or storing
the hedge trimmer always fit the cutting device cover.
Proper handling of the hedge trimmer will reduce
possible personal injury from the cutter blades.
◾
When transporting or storing the hedge trimmer,
always fit the blade cover. Proper handling of the
hedge trimmer will decrease the risk of personal injury
from the blades.
◾
When clearing jammed material or servicing the
unit, make sure all power switches are off and the
power cord is disconnected. Unexpected actuation of
the hedge trimmer while clearing jammed material or
servicing may result in serious personal injury.
◾
Hold the power tool by insulated gripping surfaces
only, because the cutter blade may contact hidden
wiring. Cutter blades contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
◾
Keep all power cords and cables away from cutting
area. Power cords or cables may be hidden in hedges or
bushes and can be accidentally cut by the blade.
BATTERY TOOL USE AND CARE
◾
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
◾
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
◾
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
◾
◾
◾
◾
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contacts
accidentally occurs, flush with water. If liquid
contact eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may
exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 100 °C may cause explosion.
IMPORTANT SAFETY INSTRUCTIONS
◾
◾
◾
Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
SERVICE
◾
ave your power tool serviced by a qualified
H
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
6
Never service damaged battery pack. Service
of battery packs should only be performed by the
manufacturer or authorised service providers.
◾
Do not use the battery-operated hedge trimmer in rain.
Do not charge the battery pack in rain or in wet locations.
Use only with the battery packs and chargers listed
below:
BATTERY PACK
CHARGER
HT2410E ONLY: BA1120E,
BA2240E, BA3360,
HT2410E/HT2000E:BA1400,
BA2800, BA4200, BA1400T,
BA2800T,BA4200T, BA5600T
CH5500E,
CH2100E
Do not grasp the exposed cutting blades or cutting
edges when picking up or holding the hedge trimmer.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
◾
◾
◾
◾
◾
Do not use on a ladder, rooftop, tree, or other unstable
support. Stable footing on a solid surface enables
better control of the hedge trimmer in unexpected
situations.
SPECIFICATIONS
Model
HT2410E
HT2000E
Never allow children to operate the hedge trimmer.
Voltage
Never remove or tamper with safety devices. Check
their proper operation regularly. Never do anything to
interfere with the intended function of a safety device
or to reduce the protection provided by a safety device.
No-Load Speed
56V
1500/min
56V
1500/min
Never operate the hedge trimmer without proper guards,
plates, or other safety protective devices in place.
Check damaged parts before further use of the hedge
trimmer. A guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorised service center unless indicated
elsewhere in this manual.
Blade Length
61cm
51cm
Cutting Capacity
26mm
25mm
Weight (without battery pack)
Recommended Operating
Temperature
Recommended Storage
Temperature
Guaranteed sound power level
3.1kg
2.9kg
0°C-40°C
0°C-40°C
-20°C-70°C -20°C-70°C
92dB(A)
PACKING LIST
PART NAME
QUANTITY
Hedge Trimmer
1
Check the blade and motor mounting bolts at frequent
intervals for proper tightness. Also, visually inspect
blade for damage (e.g., bent, cracked, and worn).
Replace the blade only with a blade from EGOTM.
Shield
1
Operator’s manual
1
◾
Replace the blade if it is bent or cracked. An
unbalanced blade causes vibration that could damage
the motor drive unit or cause personal injury.
DESCRIPTION
◾
If the equipment should start to vibrate abnormally,
stop the motor and check immediately for the cause.
Vibration is generally a warning of trouble.
◾
The trimmer shall be used to cut stems less than
26mm (HT2410E) / 25mm (HT2000E) thick.
◾
◾
Trim only in daylight or in good artificial light.
◾
Do not wash with a hose; avoid getting water in motor
and electrical connections.
◾
When servicing use only identical replacement parts
listed in this manual. Use of parts which do not meet
the original equipment specifications may lead to
improper performance and compromised safety.
◾
Follow instructions for lubricating and changing
accessories.
◾
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan this tool to someone else, also loan these
instructions to them to prevent misuse of the product
and possible injury.
◾
Remove or disconnect battery before servicing,
cleaning, or removing material from the hedge trimmer.
SAVE THESE INSTRUCTIONS!
KNOW YOUR HEDGE TRIMMER (Fig. A)
1. Hanging hole
2. Tip protector
3. Blade
4. Hand guard
5. Front handle
6. Lock-off button
7. Rear handle
8. Battery-release button
9. Latch
10. Electric contacts
11. Battery-mounting slot
12. Batter-ejection mechanism
13. Rear switch lever
14. Front switch lever
15. Hanging hole
16. Sheild
WARNING: This product has been shipped
completely assembled. The hand guard shall never
be removed during use. Once damaged, replace it
immediately by a qualified service technician.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
7
WARNING: The safe use of this product requires an
understanding of the information on the tool and in this
operator’s manual, as well as knowledge of the project
you are attempting. Before use of this product, familiarise
yourself with all operating features and safety rules.
OPERATION
WARNING: Do not allow familiarity with this product
to make you careless. Remember that a careless fraction of
a second is sufficient to inflict serious injury.
WARNING: Always wear eye protection with side
shields, along with hearing protection. Failure to do so could
result in objects being thrown into your eyes and other
possible serious injuries.
WARNING: To prevent accidental starting that
could cause serious personal injury, always remove the
battery pack from the tool when assembling parts, making
adjustments, cleaning, or when not in use.
WARNING: Do not use any attachments or
accessories not recommended by EGO . The use of
attachments or accessories not recommended can result
in serious personal injury.
HOLDING THE HEDGE TRIMMER (Fig. D, E & F)
The unit has both a front and rear handle. With the blade
directed away from you, hold the unit by both handles.
The switch lever in the front handle can be activated on
any of the three sides, giving you many choices for a
comfortable grip when performing cutting operations.
WARNING: Always keep both hands on the hedge
trimmer handles. Never hold shrubs with one hand while
operating the hedge trimmer with the other hand. Failure
to heed this warning may result in serious injury.
STARTING/STOPPING THE HEDGE TRIMMER
Before operating, remove the shield and hold the trimmer
with both hands, one hand on the rear handle and the
other on the front handle. Then check for balanced
footing, upright standing and a proper cutting distance.
To Start
1.
Install the battery pack.
2.
Depress and hold the switch lever in the front handle
with one hand.
3.
Press and hold the lock-off button with the thumb of
your other hand, then squeeze the rear switch lever
with your fingers to start the hedge trimmer. Release
the lock-off button and continue to squeeze the
trigger for continued operation.
TM
Before each use, inspect the entire product for damaged,
missing, or loose parts, such as screws, nuts, bolts, caps, etc.
Tighten securely all fasteners and caps and do not operate
this product until all missing or damaged parts are replaced.
To Stop
APPLICATION
Move the hedge trimmer away from the cutting area and
release the rear switch lever to stop the hedge trimmer.
You may use this product for trimming the hedges, shrubs
and bushes with a branch diameter of less than 26mm
(HT2410E) / 25mm (HT2000E).
NOTICE: The tool is to be used only for its prescribed
purpose. Any other use is deemed to be a case of misuse.
INSTALLING/REMOVING THE BATTERY PACK
Charge before first use.
To Install (Fig. B)
Align the battery ribs with the mounting slots and press
the battery pack down until you hear a “click”.
To Remove (Fig. C)
Depress the battery-release button and pull the battery
pack out.
WARNING: Always be aware for the location of your
feet, children, or pets when pressing the battery-release
button. Serious injury could result if the battery pack falls.
NEVER remove the battery pack at a high location.
8
WARNING: Always remove the battery pack from
the hedge trimmer during work breaks and after finishing
work.
USING THE HEDGE TRIMMER
WARNING: If the blade jams on any electrical cord
or line, DO NOT TOUCH THE BLADE! IT CAN BECOME
ELECTRICALLY LIVE AND VERY DANGEROUS. Continue
to hold the hedge trimmer by the insulated rear handle
or lay it down and away from you in a safe manner.
Disconnect the electrical service to the damaged line or
cord before attempting to free the blade from the line or
cord. Failure to heed this warning will result in serious
personal injury or possible death.
WARNING: To prevent serious personal injury, keep
hands away from blades. Do not attempt to remove cut
material or hold material to be cut when the blades are
moving. Make sure that the blades have totally stopped
and the battery pack is removed before clearing jammed
material from blades. Do not grasp the exposed cutting
blades or cutting edges when picking up or holding the unit.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
WARNING: Clear the area to be cut before each use.
Remove all objects, such as cords, lights, wire, or string
which can become entangled in the cutting blade and
create a risk of serious personal injury.
WARNING: Avoid trimming too much at one time or
through the heavy shrubbery. This can cause the blades to
bind and slow, reducing the cutting efficiency.
NOTICE: For new growth, a wide sweeping is suitable
for the stems fed directly into the cutting blade. For older
growth, a sawing movement is good for trimming the
thicker stems. A non-powered hand saw or pruning saw is
suggested for trimming the large stems first.
Top Cutting
SHARPENING THE CUTTING BLADE
1.
Start and stop your hedge trimmer until the cutter
blade and the guard are slightly offset, as shown in
Fig. I. This will allow clearance for the file between
cutter teeth and guard teeth.
2.
Remove the battery pack from your hedge trimmer.
3.
Clamp the blade assembly in a vise and file the
exposed cutting surface of each blade tooth. Remove
as little material as possible. Be sure to retain the
original angle of each tooth when filing.
4.
Remove the hedge trimmer from the vise; restart it
and stop it to expose the unsharpened edges of the
blade teeth.
5.
Remove the battery pack and repeat the sharpening
procedure above.
Use a wide sweeping motion. A slight downward tilt of the
cutting blades in the direction of motion gives the best
cutting results. For better cutting effect, you might as well
use the string to guide the hedge level as Fig. G shown.
NOTICE: Do not operate your hedge trimmer with dull or
damaged cutting blades. This may cause overload and
will give unsatisfactory cutting results.
Side Cutting
LUBRICATING THE BLADE (Fig. J)
When trimming the sides of the hedge, begin at the
bottom and cut upwards as Fig. H shown. Trim the side of
a hedge so that it will be slight narrower at the top. This
shape will expose more of the hedge to sunlight, resulting
in a more uniform growth.
For best operation and longer blade life, lubricate the
hedge trimmer blade with light weight machine oil after
every 50 hours operation.
MAINTENANCE
NOTICE: For extended using period, oil the blade during
cutting operation.
WARNING: When servicing, use only identical
replacement parts. Use of any other parts may create a
hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified
service technician.
running.
WARNING: To avoid serious personal injury, always
remove the battery pack from the product when cleaning
or performing any maintenance.
CLEANING
◾
Use a soft brush to remove debris from all air intakes
and cutting blade.
◾
To remove pitch and other sticky residue, spray the
blades with resin solvent. Run the motor briefly so that
the solvent is evenly distributed.
◾
Wipe the surface with a dry cloth.
WARNING: Never use water for cleaning your
trimmer. Avoid using solvents when cleaning plastic
parts. Most plastics are susceptible to damage from
various types of commercial solvents. Use clean clothes to
remove dirt, dust, oil, grease, etc.
Remove the battery pack and lay the trimmer onto a flat
surface. Apply the oil along the edge of the top blade.
WARNING: Do not oil while the hedge trimmer is
TRANSPORTING AND STORING
◾
Always place the shield on the blade before storing or
transporting the hedge trimmer. Use caution to avoid
the sharp teeth of the blade.
◾
◾
Clean the hedge trimmer thoroughly before storing.
◾
Keep away from corrosive agents such as garden
chemicals and deicing salts.
Store the hedge trimmer indoors, in a dry place that is
inaccessible to children.
WARNING: Blades are sharp. When handling the
blade assembly, wear non-slip, heavy-duty protective
gloves. Do not place your hand or fingers between blades
or in any position where they could get pinched or cut.
NEVER touch blades or service the unit with battery pack
installed.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
9
Protecting the environment
Do not dispose of electrical appliances as
unsorted municipal waste, use separate
collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in
landfills or dumps, hazardous substances
can leak into the groundwater and get into
the food chain, damaging your health and
well-being.
10
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
TROUBLESHOOTING
PROBLEM
Hedge trimmer
doesn’t work.
Excessive
vibration or
noise.
CAUSE
SOLUTION
◾
The battery pack is not attached to
the hedge trimmer.
◾
Attach the battery pack to the hedge trimmer.
◾
No electrical contact between the
trimmer and battery
◾
Remove battery, check contacts and reinstall the
battery pack.
◾
◾
The battery pack is depleted.
Charge the battery pack.
The battery pack is too hot.
◾
◾
◾
The hedge trimmer is too hot.
◾
Release both switch levers; allow the trimmer
to cool until the temperature drops to normal
temperature.
◾
The front and rear switch levers are
not depressed simultaneously.
◾
Press the lock-off button first and then press
the switch levers in the front and rear handle
simultaneously.
◾
The blade is jammed.
◾
Remove the battery pack from the tool, remove the
obstruction carefully, then reinsert the battery and
restart the tool.
◾
Dry or corroded blades.
◾
Lubricate the blades, following the section
“LUBRICATING THE BLADE” in this manual.
◾
Blades or blade support is bent.
◾
Replace with a new blade or support. Contact EGO
service center for blade or support replacement
service.
◾
Bent or damaged teeth.
◾
Replace with a new blade. Contact EGO service
center for blade replacement service.
◾
Loose blade bolts.
◾
Tighten the blade bolts. Using a wrench, turn the
bolt clockwise to tighten.
Remove the battery pack from the tool and allow it
to cool until the temperature drops below 67°C.
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E
11
WARRANTY
EGO WARRANTY POLICY
5 year warranty on EGO outdoor power equipment and 3 year warranty on EGO Power+ System battery packs and
chargers.
Please contact EGO customer service on Australia 1300 000 EGO(1300 000 346),
New Zealand 0508 000 EGO (0508 000 346) any time you have questions or warranty claims.
LIMITED SERVICE WARRANTY
FOR FIVE YEARS from the date of original retail purchase, this EGO product is warranted against defects in material or
workmanship. Defective product will receive free repair.
FOR THREE YEARS from the date of original retail purchase, the EGO Power+ System battery pack and charger are
warranted against defects in material or workmanship. Defective product will receive free repair.
This warranty does not cover routine maintenance parts and consumables that can wear out from normal use within the
warranty period.
◾
◾
◾
◾
◾
This warranty applies only to the original purchaser at retail and may not be transferred.
◾
T his warranty does not cover normal deterioration of the exterior finish, including but not limited to scratches, dents,
paint chips, or to any corrosion or discoloring by heat, abrasive and chemical cleaners.
The warranty period for any EGO product or part used for industrial, professional or commercial purpose is one year.
This warranty is void if the product has been used for rental purpose.
This warranty does not cover the damage resulting from modification, alteration or unauthorised repair.
T his warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect
resulting from misuse, abuse (including overloading of the product beyond capacity and exposure to water or rain),
accidents, neglect or lack of proper installation, and improper maintenance or storage.
HOW TO OBTAIN SERVICE
For warranty service, please contact EGO customer service on Australia 1300 000 EGO(1300 000 346),
New Zealand 0508 000 EGO (0508 000 346). When requesting warranty service, you must present the original dated
sales receipt. An authorised service center will be selected to repair the product according to the stated warranty terms.
ADDITIONAL LIMITATIONS
Chervon Australia Pty Ltd ABN 36 165 077 501(“Chervon”) warrants to the original domestic purchaser that this
product will be free from defects in materials and workmanship for 5 years from date of purchase, and any battery or
charger will be free from defects in materials and workmanship for 3 years from date of purchase. To make a claim,
return the faulty item together with proof of purchase directly to your closest service agent or to the place of purchase.
Any handling and transportation costs (and other expenses incurred in claiming this warranty) are not covered by this
warranty and will not be borne by Chervon. The replacement product or part or repaired product will be made available
for your collection at an address nominated by Chervon. Where a valid warranty claim is made, Chervon will replace the
defective product or repair the fault. Where the product is repaired, Chervon may use refurbished parts. This warranty
does not cover normal wear and tear, misuse or abuse. This warranty may also be further limited or voided as
specifically detailed in the product Manual. Chervon has no other liability under this warranty.The benefits to you given
by this warranty are in addition to other rights and remedies imposed by State and Federal legislation that cannot be
excluded. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. Chervon Australia Pty Ltd, Unit 14, 5 Kelletts Road, Rowville, VIC 3178.
Phone Number: Australia 1300 000 EGO(1300 000 346), New Zealand 0508 000 EGO (0508 000 346).
Email address: [email protected].
12
56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER— HT2410E / HT2000E

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project