User Manual

User Manual
LED-275 D
User Manual
Innovation, Quality, Performance
15-
Please read the instructions carefully before use
EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN 55103-1:1996, EN 55103-2:1996, EN 61000-3-2:2006,
EN 61000-3-3:1995+A1:2001+A2:2005
&
Harmonized Standard
EN 60598-2-17:1989+A2:1991, EN 60598-1:2008
EN62471:2008
Safety of household and similar electrical appliances
Part 1: General requirements
1-
14-
9. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
TABLE OF CONTENTS
y Always dry the parts carefully.
y Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
1. Safety Instructions
2. Technical Specifications
3. Installation
4. How To Set The Fixture
5. How To Control The Fixture
6. DMX 512 Configuration
7. DMX 512 Connections
8. Troubleshooting
9. Fixture Cleaning
13-
2-
1. Safety Introductions
8. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
Please read the instructions carefully which includes important
suggestions for easy troubleshooting:
information about the installation, operation and maintenance.
A. The fixture does not work, no light
WARNING
y
Please keep this User Manual for future consultation. If you sell the unit to another user,
1. Check the connection of power and main fuse.
be sure that they also receive this instruction booklet.
2. Measure the mains voltage on the main connector.
y
Unpack and check carefully there is no transportation damage before using the unit.
y
Before operating, ensure that the voltage and frequency of power supply match the
B. Not responding to DMX controller
power requirements of the unit.
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
2. If the DMX LED is on and no response to the channel, check the address settings and
y
shock.
DMX polarity.
y
The unit is for indoor use only and use only in a dry location.
y
The unit must be installed in a location with adequate ventilation, at least 50cm from
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the fixture or the previous one.
adjacent surfaces. Be sure that no ventilation slots are blocked.
4. Try to use another DMX controller.
y
Disconnect mains power before fuse replacement or servicing.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
y
Replace fuse only with the same type.
y
Make sure there are not flammable materials close to the unit while operating as it is fire
cause damage or interference to DMX interface circuit.
hazard.
C. Some fixtures don’t respond to the easy controller
y
Use safety cable when fixes this unit.
1. Check the LED for the response of the master/ slave mode signal.
y
Maximum ambient temperature is TA: 40℃ and don’t operate it where the temperature
2. Check if the unit is receiving DMX signal and cut it off.
y
Unit surface temperature may reach up to 60℃. Don’t touch the housing bare-hand
D. No response to the sound
during its operation. Turn the power off and wait for 15 minutes for cool down before
1. Make sure the fixture does not receive DMX signal.
replacing bulb or serving.
2. Check microphone to see if it is good by tapping the microphone.
is higher than this.
y
There are no user serviceable parts inside the fixture. Do not open the housing or
attempt any repairs by yourself. In the unlikely event your fixture may require service,
E. One of the channels is not working well
please contact the nearest authorized technical assistance center and always use the
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
same type spare parts. .
2. The motor’s drive IC on the PCB might be out of condition.
y
Don’t connect the device to any dimmer pack or power pack.
y
Do not look directly at the LED light beam while the fixture is on.
y
The housing must be replaced if they are visibly damaged.
y
Do not touch any wire during operation as high voltage might be causing electric shock.
y
Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.
3-
12-
7. DMX512 Connections
Direct sunlight can cause heat to build up inside of the unit, which will seriously damage
unit.
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
For power supply, do not connect in series much more than 37 units, use
another mains supply for next 37 units.
2. Technical Specifications
y
It can be operated by DMX512 control or can be used as an individual unit without
controller.
y
It can be linked together as many as required in master/slave mode, and perform the
great built-in programmed lighting shows triggered by music.
y
Please use a 3 pin XLR cable/plug when connecting them together.
y
4 Channels
Channel 1 = Shutter&Strobe
Channel 2 = Gobo
1.
Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the
Channel 3 = Rotation
fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”
Channel 4 = Dimmer
cable. Inadequate or damaged cables, soldered joints or corroded connectors can
2.
3.
4.
5.
easily distort the signal and shut down the system
y
Voltage:100V~240V 50/60Hz
The DMX output and input connectors are pass-through to maintain the DMX circuit
y
LED: 1 x 10W white
when one of the units’ power is disconnected.
y
Power consumption:16W
At last fixture, the DMX cable has to be terminated with a terminator to reduce signal
y
Fuse: T 6.3A
errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a
y
Dimension: 213 x 291 x 183mm
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
y
Weight: 3.1KG
Each lighting fixture needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
3. Installation
3 pin XLR connectors are more popular than 5 pins XLR.
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
to which you are attaching the unit is secure and is able to support a weight of 10 times of
Pin4/5: not used
the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the
unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
11-
4-
4. How To Set The Fixture
4.1 Control Panel
5.3 DMX Controller
Use universal DMX controller to control the units, you have to set DMX address from 1 to
512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 30 seconds later. To go back to the
functions without any change press the MENU button again. If you use please refer to the
following diagram to address your DMX512 channel for the first 4 units.
1 Display: To show the various menus and the selected functions
○
4 channels:
2 LED:
○
DMX
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
SOUND
Flashing
Sound activation
6. DMX512 Configuration
3 Button:
○
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
4 Safety Ring: Keep the installation safe
○
5 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal
○
6 DMX output: For DMX512 link, use 3-pin XLR plug cable to link the next unit.
○
7 Microphone: Receive music for the sound active.
○
8 Mains output: Connect to supply mains power for the next unit.
○
9 Mains input: Connect to supply mains power.
○
10 CA-9 connector: Connect and control the unit via CA-9.
○
11 CA-8 connector: Connect and control the unit via CA-8.
○
5-
10-
2. By easy controller
4.2 Main Function
3. By DMX controller
To select any functions, press MENU button until the required one is shown on the display.
No need to turn the unit off when you change the DMX address, as new DMX address
Select the function by ENTER button and the display will blink. Use DOWN and UP button to
setting will be effected at once. Every time you turn the unit on, it will show “275d” on the
change the mode. Once the required mode has been selected, press ENTER button to
display and move all the motors to their ‘home’ position. After that the unit will be ready to
setup or it will automatically return to the main functions without any change after idling 30
receive DMX signal or run the built in programs.
seconds. Back to the functions without any change press MENU button. The main functions
are shown below:
5.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when you
want an instant show. You have to set the first unit in master mode
(show 1) or
(show 2) or
(show 3) …or
and select
(show 6) mode. Its
DMX input jack will have nothing plugged into it, and Its master LED will be constantly on
and sound LED will flash to the music. The other units will have to set in slave mode
and select
(normal) or
(2 light show) mode, Their DMX cables plugged into
the DMX input jacks (daisy chain) and the slave led lights will constantly on.
2-light show
In
(slave mode),
means the unit works normally and
means
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
5.2. Easy Controller (by CA-8/CA-9)
The easy remote control is used only in master/slave mode. By
connecting to connector of the first unit, you will find that the remote
controller on the first unit will control all the other units for Stand by,
Function and Mode selection
DMX 512 Address Setting
Blackout
Blackout the unit
Function
1. Synchronous Strobe
2. Two light Strobe
3. Sound Strobe
Select
Show 1-6
Select Gobo
Mode
Sound/Strobe
(LED OFF)
Show
(LED ON)
Gobo
(LED blinking)
is shown on the display. Pressing ENTER
Press the MENU button up to when the
9-
button and the display will blink. Use DOWN and UP button to change the DMX 512 address.
Once the address has been selected, press ENTER button to setup or automatically exit
menu mode without any change after 30 seconds. Back to the previous functions without
any change press MENU button.
6-
MENU button again.
Slave Mode
Press the MENU button up to when the
button, Use DOWN and UP button to select the
(master) or
(slave 1) or
(Slave 2) mode. Once select, press the ENTER button to setup or automatically exit
menu mode without any change after 30 seconds. To go back to the functions without any
change press the MENU button
select
(normal) or
is blinking on the display. Use DOWN and UP button to
(inverse), press ENTER button to setup. Back to the
functions without any change press MENU button.
Press the MENU button up to when the
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button, Use DOWN and UP button to select the
(Show 2) or … or
Press MENU button until
Self-Test
Show Mode
1) or
Display Inverse
is shown on the display. Pressing ENTER
(Random show) or
(show
(show 6). Once select, press ENTER button to
setup or automatically exit menu mode without any change after 30 seconds. To go back to
is blinking on the display. Pressing ENTER
button and the unit will run the built-in programmer for self-test. To go back to the functions
press the MENU button.
Temperature Test
Press the MENU button up to when the
the functions without any change press the MENU button
is blinking on the display. Pressing ENTER
button and the temperature of the unit will show on the display. To go back to the functions
Sound Mode
press the MENU button.
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button, Use DOWN and UP button to select the
(sound on) or
(sound off).
Fixture Hours
Once select, press ENTER button to setup or automatically exit menu mode without any
Press the MENU button up to when the
change after 30 seconds. To go back to the functions without any change press the MENU
button and the display will show the number of working hours of the unit. To go back to the
is blinking on the display. Pressing ENTER
button
functions press the MENU button.
Software version
Blackout mode
is shown on the display. Pressing ENTER
Press the MENU button up to when the
button, Use DOWN and UP button to select the
(blackout) or
(normal).
Once select, press ENTER button to setup or automatically exit menu mode without any
change after 30 seconds. To go back to the functions without any change press the MENU
button
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the version of software of the unit. To go back to the
functions press the MENU button.
Reset
Press the MENU button up to when the
LED display
is blinking on the display. Press ENTER
button to reset the unit.
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select
(display on) or
(display off) mode. Once select, press ENTER button to setup or exit menu mode
without any change after 30 seconds. Back to the functions without any change press
7-
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
8-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement